During port creation the driver instructs the device to advertise all
the supported link modes queried from the device.
Since cited commit not all the link modes supported by the device are
supported by the driver. This can result in the device negotiating a
link mode that is not recognized by the driver causing ethtool to show
an unsupported speed:
$ ethtool swp1
...
Speed: Unknown!
This is especially problematic when the netdev is enslaved to a bond, as
the bond driver uses unknown speed as an indication that the link is
down:
[13048.900895] net_ratelimit: 86 callbacks suppressed
[13048.900902] t_bond0: (slave swp52): failed to get link speed/duplex
[13048.912160] t_bond0: (slave swp49): failed to get link speed/duplex
Fix this by making sure that only link modes that are supported by both
the device and the driver are advertised.
Fixes: b97cd89126 ("mlxsw: Remove 56G speed support")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions related to nested interface infrastructure such as
netdev_walk_all_{ upper | lower }_dev() pass both private functions
and "data" pointer to handle their own things.
At this point, the data pointer type is void *.
In order to make it easier to expand common variables and functions,
this new netdev_nested_priv structure is added.
In the following patch, a new member variable will be added into this
struct to fix the lockdep issue.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Module temperature warning events are enabled for modules that have a
temperature sensor and configured according to the temperature
thresholds queried from the module.
When a module is unplugged we are guaranteed not to get temperature
warning events. However, when a module is plugged in we need to
potentially update its current settings (i.e., event enablement and
thresholds).
Register to port module plug/unplug events and update module's settings
upon plug in events.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The overheat counter is a per-module counter, but it is exposed as part
of the corresponding netdev's statistics. It should therefore be
presented to user space relative to the netdev's lifetime.
Query the counter just before registering the netdev, so that the value
exposed to user space will be relative to this initial value.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MTWE (Management Temperature Warning Event) is triggered when module's
temperature is higher than its threshold.
Register for MTWE events and increase the module's overheat counter when
its corresponding sensor goes above the configured threshold.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the internal buffer is currently calculated in the SPAN module.
Logically it belongs to the spectrum_buffers module, where it should be
moved. However, that being a chip-specific operation, it needs dynamic
dispatch. There currently is a chip-specific structure for description of
shared buffer values, struct mlxsw_sp_sb_vals. However placing ops into
this structure would be confusing. Therefore introduce a new per-chip
structure, currently empty, and initialize the ops pointer as appropriate.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the headroom code to the spectrum_buffers module, where it
belongs.
Rename mlxsw_sp_pg_buf_threshold_get() and mlxsw_sp_pg_buf_pack() to
..._hdroom_... to match the naming convention of the new headroom code.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ETS handler performs the headroom configuration in three steps: first
it resizes the buffers and adds any new ones. Then it redirects priorities
to the new buffers. And finally it sets the size of the now-unused buffers
to zero. This way no packet drops are introduced.
This sort of careful approach will also be useful for configuring port
buffer sizes and priority map by hand, through dcbnl_setbuffer. Therefore
move the code from the DCB handler to the generic headroom function.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split mlxsw_sp_port_headroom_set() to three functions.
mlxsw_sp_hdroom_bufs_reset_sizes() changes the sizes of the individual PG
buffers, and mlxsw_sp_hdroom_configure_buffers() will actually apply the
configuration. A third function, mlxsw_sp_hdroom_bufs_fit(), verifies that
the requested buffer configuration matches total headroom size
requirements.
Add wrappers, mlxsw_sp_hdroom_configure() and __..., that will eventually
perform full headroom configuration, but for now, only have them verify the
configured headroom size, and invoke mlxsw_sp_hdroom_configure_buffers().
Have them take the `force` argument to prepare for a later patch, even
though it is currently unused.
Note that the loop in mlxsw_sp_hdroom_configure_buffers() only goes through
DCBX_MAX_BUFFERS. Since there is no logic to configure the control buffer,
it needs to keep the values queried from the FW. Eventually this function
should configure all the PGs.
Note that conversion of __mlxsw_sp_dcbnl_ieee_setets() is not trivial. That
function performs the headroom configuration in three steps: first it
resizes the buffers and adds any new ones. Then it redirects priorities to
the new buffers. And finally it sets the size of the now-unused buffers to
zero. This way no packet drops are introduced.
So after invoking mlxsw_sp_hdroom_bufs_reset_sizes(), tweak the
configuration to keep the old sizes of PG buffers for those buffers whose
size was set to zero.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, port buffers were always autoconfigured. When dcbnl_setbuffer
callback is implemented, it will allow the user to change the buffer size
configuration by hand. The sizes therefore need to be a configuration
parameter, not always deduced, and therefore belong to struct
mlxsw_sp_hdroom, where the configuration routine should take them from.
Update mlxsw_sp_port_headroom_set() to update these sizes. Have the
function update the sizes even for the case that a given buffer is not
used.
Additionally, change the loop iteration end to DCBX_MAX_BUFFERS instead of
IEEE_8021QAZ_MAX_TCS. The value is the same, but the semantics differ.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Client-side configuration has lossiness as an attribute of a priority.
Therefore add a "lossy" attribute to struct mlxsw_sp_hdroom_prio.
To a Spectrum ASIC, lossiness is a feature of a port buffer. Therefore add
struct mlxsw_sp_hdroom_buf, which in the following patches will get more
attributes, but right now only use it to track port buffer lossiness.
Instead of passing around the primary indicators of PFC and pause_en, add a
function mlxsw_sp_hdroom_bufs_reset_lossiness() to compute the buffer
lossiness from the priority map and priority lossiness. Change
mlxsw_sp_port_headroom_set() to take the buffer lossy flag from the
headroom configuration. Have the PFC and pause handlers configure priority
lossiness in mlxsw_sp_hdroom, from where it will propagate.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mapping from priorities to buffers determines which buffers should be
configured. Lossiness of these priorities combined with the mapping
determines whether a given buffer should be lossy.
Currently this configuration is stored implicitly in DCB ETS, PFC and
ethtool PAUSE configuration. Keeping it together with the rest of the
headroom configuration and deriving it as needed from PFC / ETS / PAUSE
will make things clearer. To that end, add a field "prios" to struct
mlxsw_sp_hdroom.
Previously, __mlxsw_sp_port_headroom_set() took prio_tc as an argument, and
assumed that the same mapping as we use on the egress should be used on
ingress as well. Instead, track this configuration at each priority, so
that it can be adjusted flexibly.
In the following patches, as dcbnl_setbuffer is implemented, it will need
to store its own mapping, and it will also be sometimes necessary to revert
back to the original ETS mapping. Therefore track two buffer indices: the
one for chip configuration (buf_idx), and the source one (ets_buf_idx).
Introduce a function to configure the chip-level buffer index, and for now
have it simply copy the ETS mapping over to the chip mapping.
Update the ETS handler to project prio_tc to the ets_buf_idx and invoke the
buf_idx recomputation.
Now that there is a canonical place to look for this configuration,
mlxsw_sp_port_headroom_set() does not need to invent def_prio_tc to use if
DCB is compiled out.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MTU influences sizes of auto-allocated buffers. Make it a part of port
buffer configuration and have __mlxsw_sp_port_headroom_set() take it from
there, instead of as an argument.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a priority is marked as lossless using DCB PFC, or when pause frames
are enabled on a port, mlxsw adds to port buffers an extra space to cover
the traffic that will arrive between the time that a pause or PFC frame is
emitted, and the time traffic actually stops. This is called the delay. The
concept is the same in PFC and pause, however the way the extra buffer
space is calculated differs.
In this patch, unify this handling. Delay is to be measured in bytes of
extra space, and will not include MTU. PFC handler sets the delay directly
from the parameter it gets through the DCB interface.
To convert pause handler, move MLXSW_SP_PAUSE_DELAY to ethtool module,
convert to bytes, and reduce it by maximum MTU, and divide by two. Then it
has the same meaning as the delay_bytes set by the PFC handler.
Keep the delay_bytes value in struct mlxsw_sp_hdroom introduced in the
previous patch. Change PFC and pause handlers to store the new delay value
there and have __mlxsw_sp_port_headroom_set() take it from there.
Instead of mlxsw_sp_pfc_delay_get() and mlxsw_sp_pg_buf_delay_get(),
introduce mlxsw_sp_hdroom_buf_delay_get() to calculate the delay provision.
Drop the unnecessary MLXSW_SP_CELL_FACTOR, and instead add an explanatory
comment describing the formula used.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port headroom handling is currently strewn across several modules and
tricky to follow: MTU, DCB PFC, DCB ETS and ethtool pause all influence the
settings, and then there is the completely separate initial configuraion in
spectrum_buffers. A following patch will implement the dcbnl_setbuffer
callback, which is going to further complicate the landscape.
In order to simplify work with port buffers, the following patches are
going to centralize all port-buffer handling in spectrum_buffers. As a
first step, introduce a (currently empty) struct mlxsw_sp_hdroom that will
keep the configuration parameters, and allocate and free it in appropriate
places.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce devlink health reporter to report FW fatal events. Implement
the event listener using MFDE trap and enable the events to be
propagated using MFGD register configuration.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the fw flashing code was moved to core.c, move the param which is
related to it there as well. Remove unnecessary parentheses on the way.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the firmware flashing is not specific to Spectrum, move the code to
core.c and avoid one op call and 2 exported symbols. Also, this allows
to do flash before call of driver->init function and possibly do other
core calls in between.
Do some small renaming here and there on the way to be consistent with
the rest of core.c code.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBIB register configures the size of an internal buffer that the
Spectrum ASICs use when mirroring traffic on egress. This size should be
taken into account when validating that the port headroom buffers are not
larger than the chip can handle. Up until now this was not done, which is
incidentally not a problem, because the priority group buffers that mlxsw
auto-configures are small enough that the boundary condition could not be
violated.
However when dcbnl_setbuffer is implemented, the user has control over
sizes of PG buffers, and they might overshoot the headroom capacity.
However the size of the SBIB buffer depends on port speed, and that cannot
be vetoed. Therefore SBIB size should be deduced from maximum port speed.
Additionally, once the buffers are configured by hand, the user could get
into an uncomfortable situation where their MTU change requests get vetoed,
because the SBIB does not fit anymore. Therefore derive SBIB size from
maximum permissible MTU as well.
Remove all the code that adjusted the SBIB size whenever speed or MTU
changed.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum port speed depends on link modes supported by the port, and for
Ethernet ports is constant. The maximum speed will be handy when setting
SBIB, the internal buffer used for traffic mirroring. Therefore, keep it in
struct mlxsw_sp_port for easy access.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum port MTU depends on port type. On Spectrum, mlxsw configures
all ports as Ethernet ports, and the maximum MTU therefore never changes.
Besides checking MTU configuration, maximum MTU will also be handy when
setting SBIB, the internal buffer used for traffic mirroring. Therefore,
keep it in struct mlxsw_sp_port for easy access.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches will need to register different trap groups for
Spectrum-1 and Spectrum-2 onwards.
Enable that by invoking a per-ASIC operation during trap groups
initialization.
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose via devlink-resource the maximum number of single-rate policers
and their current occupancy. Example:
$ devlink resource show pci/0000:01:00.0
...
name global_policers size 1000 unit entry dpipe_tables none
resources:
name single_rate_policers size 968 occ 0 unit entry dpipe_tables none
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add common code to handle all policer-related functionality in mlxsw.
Currently, only policer for policy engines are supported, but it in the
future more policer families will be added such as CPU (trap) policers
and storm control policers.
The API allows different modules to add / delete policers and read their
drop counter.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RED qevents early_drop and mark can be offloaded under the following
fairly strict conditions:
- At most one filter is configured at the qevent block
- The protocol is "any"
- The classifier is matchall
- The action is trap, sample, or mirror with the same conditions as
with other SPAN offloads
- The hw_counters type is none
In this patchset, implement offload of mirror for early_drop qevent.
The ECN trigger is currently not implemented in the FW and therefore
the mark qevent is not supported.
The qevent notifications look exactly like regular block binding
notifications with a binder type that identifies them as qevents.
Therefore the details of processing this binding are fairly similar
to the matchall offload.
struct flow_block_offload.sch points at the qdisc in question. Use it to
figure out if the qdisc is offloaded at all and what TC it configures.
Bounce bindings on not-offloaded qdiscs.
Individual bindings are kept in a list so that several qevents can share
the same block and all binding points get configured as the configured
filters change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two RED qevents have been introduced recently. From the point of view of a
driver, qevents are simply blocks with unusual binder types. However they
need to be handled by different logic than ACL-like flows.
Thus rename mlxsw_sp_setup_tc_block() to mlxsw_sp_setup_tc_block_clsact()
and move the binder-type dispatch from there to spectrum.c into a new
function of the original name. The new dispatcher is easier to extend with
new binder types.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-ASIC SPAN operations are relevant to the SPAN module and
therefore should be implemented there and not in the main driver file.
Move them.
These operations will be extended later on.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all the input checks are done in driver.
After adding the split capability to devlink port, move the checks to
devlink.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, port attributes like flavour, port number and whether the port
was split are set when initializing a port.
Set the split ability of the port as well, based on port_mapping->width
field and split attribute of devlink port in spectrum, so that it could be
easily passed to devlink in the next patch.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, port attributes like flavour, port number and whether the
port was split are set when initializing a port.
Set the number of lanes of the port as well so that it could be easily
passed to devlink in the next patch.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
In a fashion similar to the other Spectrum systems, enforce a specific
firmware version for Spectrum-3 so that the driver and firmware are
always in sync with regards to new features.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This version comes with fixes to the following problems, among others:
- Wrong shaper configuration on Spectrum-1
- Bogus temperature reading on Spectrum-2
- Problems in setting egress buffer size after MTU change on Spectrum-2
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain ACL actions are only available on some Spectrum revisions. In
particular, L4_PORT_ACTION is not available on Spectrum-1. Introduce a
new ops struct intended to hold these differences, mlxsw_sp_rulei_ops.
Prime it with a sole member, act_mangle_field, meant for handling of
pedit mangles.
Create two ops structures, one for Spectrum-1, the other for Spectrum-2
and above. Add callbacks for act_mangle_field and dispatch to the common
handler.
Invoke mlxsw_sp_rulei_ops.act_mangle_field from the field mangler
instead of calling the common handler directly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second commit cited below performed a cast of 'u32 buffsize' to
'(u16 *)' when calling mlxsw_sp_port_headroom_8x_adjust():
mlxsw_sp_port_headroom_8x_adjust(mlxsw_sp_port, (u16 *) &buffsize);
Colin noted that this will behave differently on big endian
architectures compared to little endian architectures.
Fix this by following Colin's suggestion and have the function accept
and return 'u32' instead of passing the current size by reference.
Fixes: da382875c6 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Fixes: 60833d54d5 ("mlxsw: spectrum: Adjust headroom buffers for 8x ports")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Suggested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port's headroom buffers are used to store packets while they
traverse the device's pipeline and also to store packets that are egress
mirrored.
On Spectrum-3, ports with eight lanes use two headroom buffers between
which the configured headroom size is split.
In order to prevent packet loss, multiply the calculated headroom size
by two for 8x ports.
Fixes: da382875c6 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to other control traps, register ACL control traps
with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to layer 2 control traps, register layer 3 control
traps with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to other traps, register layer 2 control traps with
devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bidirectional Forwarding Detection (BFD) provides "low-overhead,
short-duration detection of failures in the path between adjacent
forwarding engines" (RFC 5880).
This is accomplished by exchanging BFD packets between the two
forwarding engines. Up until now these packets were trapped via the
general local delivery (i.e., IP2ME) trap which also traps a lot of
other packets that are not as time-sensitive as BFD packets.
Expose dedicated traps for BFD packets so that user space could
configure a dedicated policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 packets that need to be forwarded and have a link-local source IP are
dropped by the kernel and an ICMPv6 "Destination unreachable" is sent to
the sending host.
As such, change the trap group of such packets so that they do not
interfere with IPv6 management packets. In the future this trap will be
exposed as an exception via devlink-trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routed IP packets with the Router Alert option need to be trapped to
the CPU as they might need to be locally delivered to raw sockets with
the IP_ROUTER_ALERT / IPV6_ROUTER_ALERT socket option.
Move them to the same group with other packets that might need to be
trapped following route lookup.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To align with recent recommended values. Will be configurable by future
patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets with an IPv6 link-local destination (i.e., fe80::/10) should not
be forwarded and are therefore trapped to the CPU for local delivery.
Since these packets are trapped for the same logical reason as packets
hitting local routes, associate both traps with the same group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet enters the device it is classified to a filtering
identifier (FID) based on the ingress port and VLAN. The FID miss trap
is used to trap packets for which a FID could not be found.
In mlxsw this trap should only be triggered when a port is enslaved to
an OVS bridge and a matching ACL rule could not be found, so as to
trigger learning.
These packets are therefore completely unrelated to packets hitting
local routes and should be in a different group. Move them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
