[Why]
The variable mismatch assignment error.
[How]
To use uint32_t replace it.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP spec requires 1000 symbols delay between the end of link training
and enabling FEC in the stream. Currently we are using 1 miliseconds
delay which is not accurate.
[how]
One lane RBR should have the maximum time for transmitting 1000 LL
codes which is 6.173 us. So using 7 microseconds delay instead of
1 miliseconds.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before was using HW counter value to determine the dprefclk. Which
take into account ss, but has large variation, not good enough for
generating audio dto. Also, the bios parser code to get the ss
percentage was not working.
[How]
After this change, dprefclk is hard coded, same as on RV. We don't
expect this to change on Renoir. Modified bios parser code to get
the right ss percentage.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new sr and pstate latencies are optimized for the case when we are not
using lpddr4 memory
[How]
have two different wm tables, one for the lpddr case and one for
non lpddr case
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When video_memory_type bw_params->vram_type
is assigned, wedistinguish between Ddr4MemType and LpDdr4MemType.
Because of this we will never report that we are using
LpDdr4MemType and never re-purpose WM set D
[How]
populate bios integrated info for renoir by adding the
revision number for renoir and use that integrated info
table instead of of asic_id to get the vram type
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On dcn21 this is programmed for tracebuffer support but isn't being
programmed on dcn20.
DMCUB execution hits an undefined address 65000000 on tracebuffer
access.
[How]
Program CW5.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Not having support for autoload isn't an error. If the DMUB firmware
doesn't support it then don't return DMUB_STATUS_INVALID.
[How]
Return DMUB_STATUS_OK when ->is_auto_load_done is NULL.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The wait for PHY init won't finish if the firmware doesn't support it.
[How]
Only hook this functionality up on DCN21 and move it out of DCN20.
For ASIC without support then this should return OK so we don't hang
while waiting in DC.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Black screen seen after display is disabled then re-enabled.
Caused by difference in link settings when
switching between different resolutions.
[How]
In PnP case, or whenever the display is
still enabled but the driver is unloaded,
disable link before re-enabling with new link settings.
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Link training failed randomly when plugging USB-C display in/out.
[How]
If link training failed, reset PHY in link re-training.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong guards were causing the debug option not to run.
[How]
Changed the guard to the correct one, matching the rq, ttu, dlg regs struct
members that need to be guarded. Also log a message when validation starts.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pstate_latency_us never gets updated from the hard coded value
in rn_clk_mgr.c
[how]
update the wm table's values before we do calculations with them
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On ASICs where number of DSCs is the same as OPPs there's no need
for DSC resource management. Mappping 1-to-1 fixes mode-set- or S3-
-related issues for such platforms.
[how]
Map DSC resources 1-to-1 to pipes only if number of OPPs is the same
as number of DSCs. This will still keep other ASICs working.
A follow-up patch to fix mode-set issues on those ASICs will be
required if testing shows issues with mode set.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Dali is currently being misinterpreted as Renoir,
as a result uses wrong clk mgr constructor
[HOW]
Add check to init Dali as Raven2 before it can be misidentified
Clean up & fix Raven2 & Dali ASIC checks
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some function pointers in the hwss function pointer table are
meant to be hw sequencer entry points to be called from dc.
However some of those function pointers are not meant to
be entry points, but instead used as a code reuse/inheritance
tool called directly by other hwss functions, not by dc.
Therefore, we want a more clear separation of which functions
we determine to be interface functions vs the functions we
use within hwss.
[How]
DC interface functions will be stored in:
struct hw_sequencer_funcs
Functions used within HWSS will be stored in:
struct hwseq_private_funcs
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
First, to make code more consistent
Second, to get rid of those scenario where we create a second
local pointer to dc when it's already passed in.
[How]
Rename core_dc to dc
Remove duplicate local pointers to dc
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers.
[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV10/14 has released. Its time to get NV10/14 bounding box
directly from code.
[How]
Retrieve NV10/14 bounding box data directly from code.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV14 is using its own ip params that's different from other
DCN2.0 ASICs.
[How]
Add ASIC revision check to make sure NV14 gets correct
ip params.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV14 IP Parameters are missing.
[How]
Add IP Parameters in.
Signed-off-by: Zhan liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
"num_vmid" and "num_dsc" are missing within NV14's resource caps structure.
[How]
Add the missing parts.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable v_total is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The msg_id field is being assigned twice. Fix this by replacing the second
assignment with an assignment to msg_size.
Addresses-Coverity: ("Unused value")
Fixes: 11a00965d2 ("drm/amd/display: Add PSP block to verify HDCP2.2 steps")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV14 is using its own ip params that's different from other
DCN2.0 ASICs.
[How]
Add ASIC revision check to make sure NV14 gets correct
ip params.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV14 IP Parameters are missing.
[How]
Add IP Parameters in.
Signed-off-by: Zhan liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't use this upstream in the Linux kernel.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
"num_vmid" and "num_dsc" are missing within NV14's resource caps structure.
[How]
Add the missing parts.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This line of code was modified. However, comments
remained unchanged. As a result, comments and code are
mismatching.
[How]
Modifying comments to reflect code. At the same time,
explaining why the value was changed from 200ms to
3000ms.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
previously event_property_validate was only called after we enabled the display.
But after "Refactor HDCP to handle multiple displays per link" this function
can be called at any time. In certain cases we don't have a aconnector
[How]
Null check aconnector and exit early. This is ok because we only need to check the
ENABLED->DESIRED transition if a connector exists.
Fixes: b1abe5586f ("drm/amd/display: Refactor HDCP to handle multiple displays per link")
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dm_pp_get_clock_levels_by_type needs to add the default clocks
to the powerplay case as well. This was accidently dropped.
Fixes: b3ea88fef3 ("drm/amd/powerplay: add get_clock_by_type interface for display")
Bug: https://gitlab.freedesktop.org/drm/amd/issues/906
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
drivers/gpu/drm/amd/amdgpu/../display/modules/hdcp/hdcp_psp.c: In function mod_hdcp_hdcp2_enable_encryption:
drivers/gpu/drm/amd/amdgpu/../display/modules/hdcp/hdcp_psp.c:633:77: warning: variable msg_out set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/modules/hdcp/hdcp_psp.c: In function mod_hdcp_hdcp2_enable_dp_stream_encryption:
drivers/gpu/drm/amd/amdgpu/../display/modules/hdcp/hdcp_psp.c:710:77: warning: variable msg_out set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:1965:26: warning:
expression which evaluates to zero treated as a null pointer constant of
type 'struct dc_dsc_config *' [-Wnon-literal-null-conversion]
update->dsc_config = false;
^~~~~
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:1971:25: warning:
expression which evaluates to zero treated as a null pointer constant of
type 'struct dc_dsc_config *' [-Wnon-literal-null-conversion]
update->dsc_config = false;
^~~~~
2 warnings generated.
Fixes: f6fe4053b9 ("drm/amd/display: Use a temporary copy of the current state when updating DSC config")
Link: https://github.com/ClangBuiltLinux/linux/issues/777
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dm_pp_get_clock_levels_by_type needs to add the default clocks
to the powerplay case as well. This was accidently dropped.
Fixes: b3ea88fef3 ("drm/amd/powerplay: add get_clock_by_type interface for display")
Bug: https://gitlab.freedesktop.org/drm/amd/issues/906
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1c42591591.
S/G display is not stable with the IOMMU enabled on some
platforms.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205523
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous patch allowed to initialize debugfs entries on both MST
and SST connectors, but MST connectors get registered much later
which exposed an issue of debugfs entries being initialized in the
same folder.
[how]
Return SST debugfs entries' initialization back to where it was.
For MST connectors we should initialize debugfs entries in connector
register function after the connector is registered.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add codes to print the detail EDC info for the subblock of mmhub
v2: Move the EDC_CNT registers' defintion from mmhub_9_4 header
files to mmhub_1_0 ones. Add mmhub_v1_0_ prefix for the local
static variable and function.
v3: squash in DC fix
Signed-off-by: Dennis Li <dennis.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1c42591591.
S/G display is not stable with the IOMMU enabled on some
platforms.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205523
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
For MST connector atomic check we have to check a new CRTC state
instead of an old one, when checking if CRTC is disabled to
release VCPI slots allocated.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
static analysis throws the error below
Out-of-bounds read (OVERRUN)
Overrunning array of 5 bytes at byte offset 7 by dereferencing pointer
(uint64_t *)hdcp->auth.msg.hdcp1.bksv.
var n is going to contain r0p and bcaps. if they are non-zero the count
will be wrong
How]
Use memcpy instead to avoid this.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we share rxstatus between HDMI and DP, so we use 16bits
The drm defines work with 1bytes at a time. So we need to
split the HDMI rxstatus into 2bytes before we can use drm defines
[How]
-create rxstatus for dp and hdmi. rxstatus for hdmi is split into bytes
using arrays.
-use drm_hdcp defines for the remaining structs
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm already has this define
[How]
drm Mask is 0x08 vs 0x0800. The reason is because drm mask
works on a byte. ^^
=======||
||
Since the first byte is always zero we can ignore it and only check the
second byte.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These defines/macros exist already no need to redefine them
[How]
Use the defines/macros from drm_hdcp.h
-we share the rxstatus between HDMI and DP (2 bytes), But upstream
defines/macros for HDMI are for 1 byte. So we need to create a separate
rxstatus for HDMI
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The old way was to poll PSP and update the properties. But due to a
limitation in the PSP interface this doesn't work for MST.
[How]
According to PSP if set_encryption return success, the link is encrypted
and the only way it will not be is if we get a link loss(which we handle
already).
So this method should be good enough to report HDCP status.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before we had a disable_type1 flag, this forced HDCP 2.2 to type0
There was no way to force type1.
[How]
Remove disable_type1 flag and instead add a flag to force type0/1.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to do this to support HDCP over MST
Currently we save a display per link, in a MST case we need to save
multiple displays per link.
[How]
We can create an array per link to cache the displays, but it
complicates the design. Instead we can use the module to cache the
displays.
Now we will always add all the displays to the module, but we use the
adjustment flag to disable hdcp on all of them before they are added.
When we want to enable hdcp we just query the display(cache), remove
it then add it back with different adjustments. Its the similar for
disable.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP 2.2 uses type0 and type1 content type. This is passed to the receiver
to stream the proper content.
For example, in a MST case if the main
device is HDCP2.2 capable but the secondary device is only 1.4 capabale
we can use Type0
Type0 content: use HDCP 1.4 or HDCP2.2 type0
Type1 content: Only use HDCP 2.2 type1
[How]
We use the "hdcp content type" property in drm. We use the
disable_type1 flag in hdcp module to select the type based on the
properties.
For updating the property we use the same logic as 1.4, but now we
consider content_type as well and update the property if the
requirements are met
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP 2.2 was disabled, we need to enable it
[How]
-Update display topology to support 2.2
-Unset hdcp2.disable in update_config
-Change logic of event_update_property, now we set the property to be
ENABLED for any level of encryption (2.2 or 1.4).
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP is a bit finicky so we try it 3 times, this leads to a case where
if we fail the first time and pass the second time the error is still
shown in dmesg for the first failed attempt.
This leads to false positive errors.
[How]
Change the logging from ERROR to WARNING. Warnings are still shown in dmesg
to know what went wrong.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to log the state changes for 2.2
This patch extends the existing logging functions to handle
HDCP2.2.
[How]
We do this by adding if/else in the defines, and output the log
based on the hdcp version
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The module works like a state machine
+-------------+
------> | Execution.c | ------
| +-------------+ |
| V
+----+ +--------+ +--------------+
| DM | -----> | Hdcp.c | <------------ | Transition.c |
+----+ <----- +--------+ +--------------+
This patch adds the execution and transition files for 2.2
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need these to read and write to aux/i2c, during
authentication
[How]
Create read/write functions for all the steps
(Eg, h_prime, paring_info etc)
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All the HDCP transactions should be verified using PSP
[How]
This patch adds the psp calls we need to verify the steps
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need some extra dmub_cmd_type for NV10
[How]
Add command table functions in DMUB firmware.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Xiong Yan <Xiong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to be able to enable native 422 for debugging purposes.
[How]
Add new dc_debug_options bool and check it in the get_dsc_enc_caps
function.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When updating DSC config, a new config has to be validated before proceeding
with applying the update. Validation, however, modifies the current state.
This means DSC config validation would affect pipe re-assignment, causing
intermittent screen corruption issues when ODM is required for DSC.
[how]
- Use a copy of the current state for modified DSC config validation
- Set the update type to FULL_UPDATE to correctly validate and set the
actual state used for committing the streams
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN will hang if we access registers before PHY init is done.
So we need to spin or abort.
[How]
On hardware with DMCUB running and working we shouldn't time out
waiting for this to finish and we shouldn't hit the spin cycle.
If there's no hardware support then we should exit out of the function
early assuming that PHY init was already done elsewhere.
If we hit the timeout then there's likely a bug in firmware or software
and we need to debug - add errors and asserts as appropriate.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need validation that we are programming the expected values (rq, ttu, dlg)
from DML. This debug feature will output logs if we are programming
incorrect values and may help differentiate DAL issues from HW issues.
[How]
Dump relevant registers for each pipe with active stream. Compare current
reg values with the converted DML output. Log mismatches when found.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is becoming increasingly hard to figure out which
function is called on the different DCN versions
[How]
1. Make function pointer table init in its own init.c file
2. Remove other scenarios in hwseq.c file that need to
include headers of other DCN versions. (If needed,
it should have been done via the function pointers)
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's an interface violation to use infinite loops within DMUB
service functions and we'll lock up the kernel by doing so.
[How]
Revert the function back to its intended functionality.
Move the infinite loops into DC/DM as necessary.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There can be a conflict between OS HDR multiplier and 3dlut HDR
multiplier, which are both sent to DC.
[HOW]
Instead of having dc determine which HDR multiplier to use, make the
decision in dm and send only the intended value in a surface update.
Store the current OS HDR multiplier and determine whether to use it or
the 3dlut's multiplier before sending the surface update to dc. Send
multiplier to dc in fixed31_32 format, dc then converts it to hw format.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
need to send immediate SDP message via debugfs on Navi board.
[how]
hook up the DCN1x encoder function of sending immediate sdp
message to DCN2.
Signed-off-by: David (Dingchen) Zhang <dingchen.zhang@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. Add trace code enum for easy debugging.
2. Add trace during uC boot up, including loading phy FW
and dmcu FW.
3. Change cache memory type back to write back,
since write through has issue when resume from S0i3 100% hang after
3.2ms.
4. Change CW3 base address to hard code value to avoid memory overlap
with cw1.
5. Change polling phy init done to infinite loop to avoid dcn hang when
dmcub uC stalled.
6. Add dmcub FW dis-assembly file to repositatory for debug purpose.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a case where the margin is between 50 and 60, but applying the
workaround causes a hang. By increasing the threshold, we are blocking more
cases from switching p-state during active, but those cases will fall back
to switching during blank, which is fine.
[How]
- increase required margin from 50 to 60
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In the TEST_MSIC dpcd register field definition, the test equipment
has the option to choose between YCbCr601 or YCbCr709.
We will apply corresponding YCbCr coefficient based on this test
request.
[how]
Add a new input parameter in dc_link_dp_set_test_pattern to allow the
selection between different color space.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Too many construct functions which makes searching
difficult, especially on some debuggers.
[How]
Append all construct and destruct functions with dcn
number and object type to make each construct function
name unique
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous patch allowed to initialize debugfs entries on both MST
and SST connectors, but MST connectors get registered much later
which exposed an issue of debugfs entries being initialized in the
same folder.
[how]
Return SST debugfs entries' initialization back to where it was.
For MST connectors we should initialize debugfs entries in connector
register function after the connector is registered.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hanging on RV for DTN driver verifier
[How]
Roll back change and investigate further
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In SST mode no idle pattern will be generated after link training if
DIG FE is not connected to DIG BE.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We were missing debugfs files on MST connectors as the files
weren't initialized.
[how]
Move connector debugfs initialization into connoctor's
init helper function so it will be called by both SST and MST
connectors. Also move connector registration so it will be
registered before we create the entries.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
By default we shouldn't be trying to write secure registers during
DMUB hardware init.
[How]
Add a parameter to control whether we put the DMCUB into secure reset
and attempt to load CW0/CW1.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to avoid reprogramming the cache window when possible.
We don't need to worry about it for S3 but we *do* need to worry about
it for S4 resume.
DM can check whether hardware should be reinitialized or store software
state when going to S4 to know whether we need to reprogram hardware.
[How]
Add helpers to the DMUB service to check hardware initialization state.
DM will hook it up later.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes in dc to allow for different cases where full update is
required.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When sending DCC with Stereo, DCC gets enabled but the meta addresses
are 0. This happens momentarily before the meta addresses are populated
with a valid address.
[How]
Add call validate_dcc_with_meta_address() in
copy_surface_update_to_plane() to check for surface address and DCC
change.
When DCC has changed, check if DCC enable is true but meta address is 0.
If so, we turn DCC enable to false. When surface address has changed, we
check if DCC enable is false but meta address is not 0. If so, we turn
DCC enable back to true. This will restore DCC enable to the proper
setting once the meta address is valid.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDMI 2.0 HF-VSDB in EDID defines supported color depths in YCBCR420 modes.
But we did not honor these bit masks when choosing pixel encoding.
HDMI 2.0 compliance tests with deep color and YCBCR420 failed as a result.
[How]
Cap color depth based on y420_dc_modes from EDID.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Background color only takes effect in bottommost mpcc.
[How]
Update background color in bottommost mpcc.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debug purpose, we need to check HUBP_CLOCK_ENABLE in DTN
log debugfs on Navi.
[How]
Add related register read in dcn20_hubp.c.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before we were reading registers specific to luma size, which caused a black line
to appear on the screen from time to time, as although the luma row height
is generally the same as the chroma row height for the video case, it will sometimes
be one more
[how]
Read the register specific for the chroma size
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
we want to increase the pte row plus 1 line if chroma viewport
height is integer multiple of the pte row height
[how]
instead of ceiling viewport height, we floor it. this allows
us to accommodate both cases: those where the chroma viewport
height is integer multiple of the pte row height and those where
it is not
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An old display with no audio may not have an EDID with a CEA block, or
it may simply be too old to support audio. This is not a driver error,
so don't flag it as such.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112140
References: ae2a349597 ("drm/amd: be quiet when no SAD block is found")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/modules/color/color_gamma.c: In function build_freesync_hdr:
drivers/gpu/drm/amd/display/modules/color/color_gamma.c:830:20: warning: variable min_content set but not used [-Wunused-but-set-variable]
It is not used since commit 50575eb5b3 ("drm/amd/display:
Only use EETF when maxCL > max display")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/bios/bios_parser.c: In function bios_get_board_layout_info:
drivers/gpu/drm/amd/display/dc/bios/bios_parser.c:2743:22: warning: variable bp set but not used [-Wunused-but-set-variable]
It is introduced by commit 1eeedbcc20 ("drm/amd/display:
get board layout for edid emulation"), but never used,
so remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/bios/bios_parser2.c: In function bios_get_board_layout_info:
drivers/gpu/drm/amd/display/dc/bios/bios_parser2.c:1826:22: warning: variable bp set but not used [-Wunused-but-set-variable]
It is introduced by commit 1eeedbcc20 ("drm/amd/display:
get board layout for edid emulation"), but never used,
so remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c: In function dm_determine_update_type_for_commit:
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c:6516:36: warning: variable old_plane_crtc set but not used [-Wunused-but-set-variable]
It is introduced by commit a87fa99387 ("drm/amd/display:
Build stream update and plane updates in dm"), but never used,
so remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c: In function get_pbn_from_timing:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:2364:11: warning:
variable bpc set but not used [-Wunused-but-set-variable]
It is not used since commit e49f69363a ("drm/amd/display: use
proper formula to calculate bandwidth from timing"), this also
remove get_color_depth(), which is only used here.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c: In function dp_wa_power_up_0010FA:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:2320:35: warning:
variable ds_port set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the static keyword to the front of declarations.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is comparison expression that is duplicated and hence one
of the expressions can be removed. Remove it.
Addresses-Coverity: ("Same on both sides")
Fixes: 12e2b2d4c6 ("drm/amd/display: add dcc programming for dual plane")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are spelling mistakes in a DC_ERROR message and a comment.
Fix these.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Variable status is redundant, it is being initialized with a value
that is over-written later and this is being returned immediately
after the assignment. Clean up the code by removing status and
just returning the value returned from the call to function
dc->hwss.dmdata_status_done.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dm_dcn_crtc_high_irq() is only used when CONFIG_DRM_AMD_DC_DCN is set.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since dcn20 and dcn21 are under dcn1 it doesnt make sense to
have it named dcn1.
Change it to "dcn" to make it generic
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN21 is stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup Renoir definitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN21 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN2 and DSC are stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup NV defninitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN2 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* dce/dce_dmcu.c: dcn20_*lock_phy()
* dce/dce_dmcu.c: dcn20_funcs
* dce/dce_dmcu.c: dcn20_dmcu_create()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On DCN hardware, the crtc_high_irq handler makes vupdate_high_irq
handler redundant.
All the vupdate handler does is handle vblank events, and update vrr
for DCE hw (excluding VEGA, more on that later). As far as usermode is
concerned. vstartup happens close enough to vupdate on DCN that it can
be considered the "same". Handling vblank and updating vrr at vstartup
effectively replaces vupdate on DCN.
Vega is a bit special. Like DCN, the VRR registers on Vega are
double-buffered, and swapped at vupdate. But Unlike DCN, it lacks a
vstartup interrupt. This means we can't quite remove the vupdate handler
for it, since delayed user events due to vrr are sent off there.
[How]
Remove registration of vupdate interrupt handler for DCN. Disable
vupdate interrupt if asic family DCN, enable otherwise.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DCN hardware, the crtc_high_irq handler is assigned to the vstartup
interrupt. This is different from DCE, which has it assigned to vblank
start.
We'd like to send vblank and user events at vstartup because:
* It happens close enough to vupdate - the point of no return for HW.
* It is programmed as lines relative to vblank end - i.e. it is not in
the variable portion when VRR is enabled. We should signal user
events here.
* The pflip interrupt responsible for sending user events today only
fires if the DCH HUBP component is not clock gated. In situations
where planes are disabled - but the CRTC is enabled - user events won't
be sent out, leading to flip done timeouts.
Consequently, this makes vupdate on DCN hardware redundant. It will be
removed in the next change.
[How]
Add a DCN-specific crtc_high_irq handler, and hook it to the VStartup
signal. Inside the DCN handler, we send off user events if the pflip
handler hasn't already done so.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1-Read lttpr caps in 5-bytes
2-Parse caps
3-Validate caps and set lttpr_mode
4-Use hw default timeout when lttpr is disabled.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The aux timeout value is not default before reading link cap.
Setting it to default when lttpr is not enabled causes some monitor
not to light up.
[How]
Read the aux engine timeout value before setting it to extended.
Set the aux engine timeout to its previous value if no lttpr.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1-If at least one repeater is present in the link and we are in non
transparent mode, perform clock recovery then channel equalization
with all repeaters one by one before training DPRX.
2-Mark the end of LT with a repeater by setting training pattern 0
at the end of channel equalization with each repeater.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1-Grant extended timeout request. Done once after detection
2-Configure lttpr mode based on lttpr support before LT
3-Account for lttpr cap when determining max link settings
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
LTTPR was introduced after DP1.2. Reading LTTPR registers 0xFXXXX
on some DP 1.2 display is causing an unexpected behavior.
[How]
Make sure that we don't read any lttpr registers on 1.2 displays.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
When reading link, update the procedure as follows:
1-Set aux timeout to extended: 3.2ms
2-Start with reading lttpr caps
3-Determine if lttpr support should be enabled. Reset aux timeout to
400us if no repeater is found.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We want to guarantee integer ratio scaling for all scaling modes.
[how]
Treat centered, fullscreen, preserve aspect ratio the same: scale
the view as many times as possible, and fill in the rest with a black
border.
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need it for some OEM I2C devices in Nv10
[how]
Link up code to parse OEM table and expose DC interface
to access the pins
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debug purpose, we need to check the following hardware status
in DTN log debugfs:
1.dpp & hubp clock enable;
2.crtc blank enable;
3.link phy status;
[How]
Add the upper information in the amdgpu_dm_dtn_log debugfs.
For CRTC blanked status, since DCN2 and greater reports it on the OPP
instead of OTG, we patch it in after calling optc1_read_otg_states.
Ideally, this should be done in the DCN version specific function hooks.
It has been left as a TODO item.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System is unable to enter S0i3 due to DISPLAY_OFF_MASK not asserted
in SMU.
[How]
Optimized bandwidth should be called paired and to resolve unplug
display underflow issue, optimize bandwidth after commit streams is
moved to next page flip, in case of S0i3, there is a change for no
flip coming causing display count is 1 in SMU side.
Add optimize bandwidth after commit stream.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It has been a useful option in debugging GFXOFF and P.State Change issues.
May be required as for platform specific workaround.
[HOW]
Create option in enum dc_debug_options, "disable_vactive_clock_change".
When it is set, dm_dram_clock_change_vactive, will translate into
p_state_change_support: false.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is confusing to sinks if we send VSC SDP only on some format. Today we
signal colorimetry format using MSA while in formats like sRGB.
But when we switch to BT2020 we set the bit to ignore MSA colorimetry and
instead use the colorimetry information in the VSC SDP.
But if sink supports signaling of colorimetry via VSC SDP we should always
set the MSA MISC1 bit 6, instead of doing so selectively.
[How]
If sink supports signaling of colorimetry via VSC SDP, and we are sending
the colorimetry info via VSC SDP with packet revision 05h, then always
set MSA MISC1 bit 6.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If acquire/release DSC resource sequence is affected by a regression,
it can happen that the already-in-use DSC HW block is being wrongly
re-used for a different pipe. The reverse is also possible, i.e.
already-disabled DSC HW block could be disabled from other context.
[how]
Read back the enable state of DSC HW and report an error if duplicate
enable or disable was attempted.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently made a change where disable_output is called using signal_type.
Using actual signal_type when calilng disable_output in power_down_encoders
would make DP to HDMI dongle not light up on boot. As it would have signal_type
SIGNAL_TYPE_DISPLAY_PORT.
[HOW]
Set signal_type to SIGNAL_TYPE_NONE unless it is eDP.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For unknown reason, immediate flip with host VM translation on NV12
surface will underflow on last row of PTE.
[How]
Hack chroma viewport height to make fetch one more row of PTE.
Note that this will cause hubp underflow on all video underlay
cases, but the underflow is not user visible since it is in
blank region.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
V.Active dram clock change workaround need a small modification for DMLv2
to ensure that the dummy p-state check doesn't fail.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Support for DMUB only depends on support for DC. It doesn't use floating
point so we don't need to guard it by any specific DCN revision.
[How]
Drop the guards and cleanup the newlines around each one.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC can utilize the DMUB server to send commands to the DMUB but it's
the DM responsibility to pass it the service to use.
[How]
Create the dc_dmub_srv after we finish initializing the dmub_srv.
Cleanup the dc_dmub_srv before destroying the dmub_srv or dc.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC will use DMUB for command submission and flow control during
initialization.
Register offloading as well as submitting some BIOS commands are part
of the DC internal interface but are guarded behind debug options.
It won't be functional in amdgpu_dm yet since we don't pass the
DMUB service to DC for use.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need DMCUB on Renoir to support DMCU and PHY initialization.
The DMUB service provides a mechanism to load the DMCUB.
[How]
Include the DMUB service in amdgpu_dm.
Frontdoor loading of the DMCUB firmware needs to happen via PSP. To
pass the firmware to PSP we need to hand it off to the firmware list
in the base driver during software initialization.
Most of the DMUB service can technically be initialized at this point
in time, but we don't want to be allocating framebuffer memory for
hardware that doesn't support the DMCUB and in order to check that we
need to be able to read registers - something DM helpers aren't setup
to do in software initialization.
So everything but the service creation itself will get deferred to
hardware initialization.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSP version format is AB.CD.EF.GH, where CD and GH is the main version.
current psp version check for dmcub loading dmcu check 0x00110029, in
case of some psp version eg: 0x00110227 which main version should be
0x00110027, will result in unexpeceted dmcub loading dmcu FW.
[How]
Add psp version mask 0x00FF00FF for checking version.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The DMUB service is the interface to the DMCUB.
It's required to support Renoir features so it will be enabled and
compiled automatically when the Renoir display engine is enabled via
CONFIG_DRM_AMD_DC_DCN2_1.
DMUB code will initially be guarded by CONFIG_DRM_AMD_DC_DMUB and later
switched to CONFIG_DRM_AMD_DC_DCN2_1 with the config option dropped.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The interface to the DMCUB won't be through DC itself. DC will instead
call into the DMUB interface introduced with a future change.
The CONFIG_DRM_AMD_DC_DMUB defines will still be used for now but will
be dropped at the end of the series.
Since this define was never configurable in the first place this code
wasn't used.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently pointer aconnector is being dereferenced by the call to
to_dm_connector_state before it is being null checked, this could
lead to a null pointer dereference. Fix this by checking that
aconnector is null before dereferencing it.
Addresses-Coverity: ("Dereference before null check")
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Adding encoder atomic check to find vcpi slots for a connector
- Using DRM helper functions to calculate PBN
- Adding connector atomic check to release vcpi slots if connector
loses CRTC
- Calculate PBN and VCPI slots only once during atomic
check and store them on crtc_state to eliminate
redundant calculation
- Call drm_dp_mst_atomic_check to verify validity of MST topology
during state atomic check
v2: squashed previous 3 separate patches, removed DSC PBN calculation,
and added PBN and VCPI slots properties to amdgpu connector
v3:
- moved vcpi_slots and pbn properties to dm_crtc_state and dc_stream_state
- updates stream's vcpi_slots and pbn on commit
- separated patch from the DSC MST series
v4:
- set vcpi_slots and pbn properties to dm_connector_state
- copy porperties from connector state on to crtc state
v5:
- keep the pbn and vcpi values only on connnector state
- added a void pointer to the stream state instead on two ints,
because dc_stream_state is OS agnostic. Pointer points to the
current dm_connector_state.
v6:
- Remove new param from stream
v7:
- Fix error with using max capable bpc
v8:
- squash in fix from Gustavo A. R. Silva
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl3IqJQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGOiUH+gOEDwid5OODaFAd
CggXugdFIlBZefKqGVNW5sjgX8pxFWHXuEMC8iNb6QXtQZdFrI6LFf9hhUDmzQtm
6y1LPxxEiTZjObMEsBNylb7tyzgujFHcAlp0Zro3w/HLCqmYTSP3FF46i2u6KZfL
XhkpM4X7R7qxlfpdhlfESv/ElRGocZe6SwXfC7pcPo5flFcmkdu9ijqhNd/6CZ/h
Nf9rTsD/wEDVUelFbgVN+LJzlaB0tsyc4Zbof07n8OsFZjhdEOop8gfM/kTBLcyY
6bh66SfDScdsNnC/l8csbPjSZRx+i+nQs67DyhGNnsSAFgHBZdC4Tb/2mDCwhCLR
dUvuYZc=
=1N6F
-----END PGP SIGNATURE-----
Merge v5.4-rc7 into drm-next
We have the i915 security fixes to backmerge, but first
let's clear the decks for other drivers to avoid a bigger
mess.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the ddc pointer provided by the generic connector.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <40293fa4e619d1d1af213a076b1d03440e50c56c.1566845537.git.andrzej.p@collabora.com
This reverts commit 967a3b85ba.
Reason for revert: Root cause of this issue is found. The workaround is not needed anymore.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Navi10 has 6 PHY, but Navi14 only has 5 PHY, that is
because there is no ENGINE_ID_DIGD in Navi14. Without
this patch, many HDMI related issues (e.g. HDMI S3
resume failure, HDMI pink screen on boot) will be
observed.
[How]
If "eng_id" is larger than ENGINE_ID_DIGD, then
add "eng_id" by 1.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Neil Mayhew <neil@neil.mayhew.name>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 385857adb8.
Reason for revert: Root cause of this issue is found. The workaround is not needed anymore.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Navi10 has 6 PHY, but Navi14 only has 5 PHY, that is
because there is no ENGINE_ID_DIGD in Navi14. Without
this patch, many HDMI related issues (e.g. HDMI S3
resume failure, HDMI pink screen on boot) will be
observed.
[How]
If "eng_id" is larger than ENGINE_ID_DIGD, then
add "eng_id" by 1.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
-dma-buf: Introduce and revert dma-buf heap (Andrew/John/Sean)
Cross-subsystem Changes:
- None
Core Changes:
-dma-buf: add dynamic mapping to allow exporters to choose dma_resv lock
state on mmap/munmap (Christian)
-vram: add prepare/cleanup fb helpers to vram helpers (Thomas)
-ttm: always keep bo's on the lru + ttm cleanups (Christian)
-sched: allow a free_job routine to sleep (Steven)
-fb_helper: remove unused drm_fb_helper_defio_init() (Thomas)
Driver Changes:
-bochs/hibmc/vboxvideo: Use new vram helpers for prepare/cleanup fb (Thomas)
-amdgpu: Implement dma-buf import/export without drm helpers (Christian)
-panfrost: Simplify devfreq integration in driver (Steven)
Cc: Christian König <christian.koenig@amd.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Steven Price <steven.price@arm.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Sean Paul <seanpaul@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHF6rntfJ3enn8gh8cywAJXLcr3kFAl27NYYACgkQcywAJXLc
r3k7SQgAy7MbT7MHg1NkObnWFKwbNxA0FuRV7HVuQ5AiVA5fbehGECNVI1hFZE3D
kCyL5zRgzfrbBjI9zqclonXPmjPbD//f+ufUZJ2EaWHfE5k7LUYIEunpgWlCEgUR
qqeuqjvx2+NY3gLZW6D8BIrUW79cKbggBvDa9QeE4aoMiI7/F3lpNog5LNo7TWCQ
4SGgpDqtcJ2eSBneX80zLLVnI1CKfCSiWheZVoqCTRN5bfUftGwhbXb3N/JipG37
cCblVR7D8FR7z0MQUtq2ql76tCn5SJJqloujkmUU06quYBHR5K1deB5BP+8HI1Fw
/XMqWHFo0uX7h4hFIt1MVIJ92U+b+w==
=ViNo
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-10-31' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.5:
UAPI Changes:
-dma-buf: Introduce and revert dma-buf heap (Andrew/John/Sean)
Cross-subsystem Changes:
- None
Core Changes:
-dma-buf: add dynamic mapping to allow exporters to choose dma_resv lock
state on mmap/munmap (Christian)
-vram: add prepare/cleanup fb helpers to vram helpers (Thomas)
-ttm: always keep bo's on the lru + ttm cleanups (Christian)
-sched: allow a free_job routine to sleep (Steven)
-fb_helper: remove unused drm_fb_helper_defio_init() (Thomas)
Driver Changes:
-bochs/hibmc/vboxvideo: Use new vram helpers for prepare/cleanup fb (Thomas)
-amdgpu: Implement dma-buf import/export without drm helpers (Christian)
-panfrost: Simplify devfreq integration in driver (Steven)
Cc: Christian König <christian.koenig@amd.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Steven Price <steven.price@arm.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031193015.GA243509@art_vandelay
A final attempt at enabling sse2 for GCC users.
Orininally attempted in:
commit 1011745073 ("drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines")
Reverted due to "reported instability" in:
commit 193392ed9f ("Revert "drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines"")
Re-added just for Clang in:
commit 0f0727d971 ("drm/amd/display: readd -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines")
The original report didn't have enough information to know if the GPF
was due to misalignment, but I suspect that it was. (The missing
information was the disassembly of the function at the bottom of the
trace, to see if the instruction pointer pointed to an instruction with
16B alignment memory operand requirements. The stack trace does show
the stack was only 8B but not 16B aligned though, which makes this a
strong possibility).
Now that the stack misalignment issue has been fixed for users of GCC
7.1+, reattempt adding -msse2. This matches Clang.
It will likely never be safe to enable this for pre-GCC 7.1 AND use a
16B aligned stack in these translation units.
This is only a functional change for GCC 7.1+ users, and should be boot
tested.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=109487
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GCC earlier than 7.1 errors when compiling code that makes use of
`double`s and sets a stack alignment outside of the range of [2^4-2^12]:
$ cat foo.c
double foo(double x, double y) {
return x + y;
}
$ gcc-4.9 -mpreferred-stack-boundary=3 foo.c
error: -mpreferred-stack-boundary=3 is not between 4 and 12
This is likely why the AMDGPU driver was ever compiled with a different
stack alignment (and thus different ABI) than the rest of the x86
kernel. The kernel uses 8B stack alignment, while the driver was using
16B stack alignment in a few places.
Since GCC 7.1+ doesn't error, fix the ABI mismatch for users of newer
versions of GCC.
There was discussion about whether to mark the driver broken or not for
users of GCC earlier than 7.1, but since the driver currently is
working, don't explicitly break the driver for them here.
Relying on differing stack alignment is unspecified behavior, and
brittle, and may break in the future.
This patch is no functional change for GCC users earlier than 7.1. It's
been compile tested on GCC 4.9 and 8.3 to check the correct flags. It
should be boot tested when built with GCC 7.1+.
-mincoming-stack-boundary= or -mstackrealign may help keep this code
building for pre-GCC 7.1 users.
The version check for GCC is broken into two conditionals, both because
cc-ifversion is currently GCC specific, and it simplifies a subsequent
patch.
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The x86 kernel is compiled with an 8B stack alignment via
`-mpreferred-stack-boundary=3` for GCC since 3.6-rc1 via
commit d9b0cde91c ("x86-64, gcc: Use -mpreferred-stack-boundary=3 if supported")
or `-mstack-alignment=8` for Clang. Parts of the AMDGPU driver are
compiled with 16B stack alignment.
Generally, the stack alignment is part of the ABI. Linking together two
different translation units with differing stack alignment is dangerous,
particularly when the translation unit with the smaller stack alignment
makes calls into the translation unit with the larger stack alignment.
While 8B aligned stacks are sometimes also 16B aligned, they are not
always.
Multiple users have reported General Protection Faults (GPF) when using
the AMDGPU driver compiled with Clang. Clang is placing objects in stack
slots assuming the stack is 16B aligned, and selecting instructions that
require 16B aligned memory operands.
At runtime, syscall handlers with 8B aligned stack call into code that
assumes 16B stack alignment. When the stack is a multiple of 8B but not
16B, these instructions result in a GPF.
Remove the code that added compatibility between the differing compiler
flags, as it will result in runtime GPFs when built with Clang. Cleanups
for GCC will be sent in later patches in the series.
Link: https://github.com/ClangBuiltLinux/linux/issues/735
Debugged-by: Yuxuan Shui <yshuiv7@gmail.com>
Reported-by: Shirish S <shirish.s@amd.com>
Reported-by: Yuxuan Shui <yshuiv7@gmail.com>
Suggested-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc.c:583:null check is needed after using kzalloc function
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: zhongshiqi <zhong.shiqi@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This patch is for fixing Navi14 HDMI display pink screen issue.
[How]
Call stream->link->link_enc->funcs->setup twice. This is setting
the DIG_MODE to the correct value after having been overridden by
the call to transmitter control.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
i2c_read is called to differentiate passive DP->HDMI and DP->DVI-D dongles
The call is expected to fail in DVI-D case but pass in HDMI case
Some HDMI dongles have a chance to fail as well, causing misdetection as DVI-D
[HOW]
Retry i2c_read to ensure failed result is valid
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There's a use case for inverted gamma
and it's been confirmed that negative slopes are ok.
[how]
Remove code for blocking non-monotonically increasing gamma
Signed-off-by: Aidan Yang <Aidan.Yang@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A display that supports DRR can never really be considered
"synchronized" with any other display because we can dynamically
enable DRR (i.e. without modeset). this will cause their
relative CRTC positions to drift and lose sync. this will disrupt
features such as MCLK switching that assume and depend on
their permanent alignment (that can only change with modeset)
[how]
check for ignore_msa in stream when considered synchronizability
this ignore_msa is basically actually implemented as "supports drr"
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DWB (Display Writeback) flag needs to be enabled as 1, or system
will throw out a few warnings when creating dcn20 resource pool.
Also, Navi14's dwb setting needs to match Navi10's,
which has already been set to 1.
[How]
Change value of num_dwb from 0 to 1.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:2520:42:
error: implicit conversion from enumeration type 'enum transmitter' to
different enumeration type 'enum physical_phy_id'
[-Werror,-Wenum-conversion]
psr_context->smuPhyId = link->link_enc->transmitter;
~ ~~~~~~~~~~~~~~~~^~~~~~~~~~~
1 error generated.
As the comment above this assignment states, this is intentional. To
match previous warnings of this nature, add a conversion function that
explicitly converts between the enums and warns when there is a
mismatch.
See commit 828cfa2909 ("drm/amdgpu: Fix amdgpu ras to ta enums
conversion") and commit d9ec5cfd5a ("drm/amd/display: Use switch table
for dc_to_smu_clock_type") for previous examples of this.
v2: use PHYLD_UNKNOWN for the default case.
Fixes: e0d08a40a6 ("drm/amd/display: Add debugfs entry for reading psr state")
Link: https://github.com/ClangBuiltLinux/linux/issues/758
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kfree has taken null pointer into account. hence it is safe to remove
the unnecessary check.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
* Handle UP requests asynchronously in the DP MST helpers, fixing
hotplug notifications and allowing us to implement suspend/resume
reprobing
* Add basic suspend/resume reprobing to the DP MST helpers
* Improve locking for link address reprobing and connection status
request handling in the DP MST helpers
* Miscellaneous refactoring in the DP MST helpers
* Add a Kconfig option to the DP MST helpers to enable tracking of
gets/puts for topology references for debugging purposes
Driver Changes:
* nouveau: Resume hotplug interrupts earlier, so that sideband
messages may be transmitted during resume and thus allow
suspend/resume reprobing for DP MST to work
* nouveau: Avoid grabbing runtime PM references when handling short DP
pulses, so that handling sideband messages in resume codepaths with the
DP MST helpers doesn't deadlock us
* i915, nouveau, amdgpu, radeon: Use detect_ctx for probing MST
connectors, so that we can grab the topology manager's atomic lock
Note: there's some amdgpu patches that I didn't realize were pushed
upstream already when creating this topic branch. When they fail to
apply, you can just ignore and skip them.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a74c6446bc960190d195a751cb6d8a00a98f3974.camel@redhat.com
drm-next-5.5-2019-10-25:
amdgpu:
- BACO support for CI and VI asics
- Quick memory training support for navi
- MSI-X support
- RAS fixes
- Display AVI infoframe fixes
- Display ref clock fixes for renoir
- Fix number of audio endpoints in renoir
- Fix for discovery tables
- Powerplay fixes
- Documentation fixes
- Misc cleanups
radeon:
- revert a PPC fix which broke x86
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191025221020.203546-1-alexander.deucher@amd.com
Fix sparse warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:963:6:
warning: symbol 'calculate_integer_scaling' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc.c:583:null check is needed after using kzalloc function
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: zhongshiqi <zhong.shiqi@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/display/dc/dce/dce_aux.c: In function dce_aux_configure_timeout:
drivers/gpu/drm/amd/display/dc/dce/dce_aux.c: warning: variable timeout set but not used [-Wunused-but-set-variable]
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some LED panel drivers might not like fractional PWM. In such cases,
backlight flickering may be observed.
[How]
Add a DC feature mask to disable fractional PWM, and associate it with
the preexisting dc_config flag.
The flag is only plumbed through the dmcu firmware, so plumb it through
the driver path as well.
To disable, add the following to the linux cmdline:
amdgpu.dcfeaturemask=0x4
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204957
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Lukáš Krejčí <lskrejci@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DWB (Display Writeback) flag needs to be enabled as 1, or system
will throw out a few warnings when creating dcn20 resource pool.
Also, Navi14's dwb setting needs to match Navi10's,
which has already been set to 1.
[How]
Change value of num_dwb from 0 to 1.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Adding psr mask to dc features allows selectively disable/enable psr.
Current psr implementation may not work with non-pageflipping application.
Until resolved it should be disabled by default.
[How]
Add dcfeaturemask for psr enablement. Disable by default.
To enable set amdgpu.dcfeaturemask=0x8 in grub kernel command line.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With this cleanup, the APIs from amdgpu_smu.c will map to
ASIC specific ones directly. Those can be shared around
all SMU V11/V12 ASICs will be put in smu_v11_0.c and
smu_v12_0.c respectively.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a quick and low risk fix. Those APIs which
are exposed to other IPs or to support sysfs/hwmon
interfaces or DAL will have lock protection. Meanwhile
no lock protection is enforced for swSMU internal used
APIs. Future optimization is needed.
V2: strip the lock protection for all swSMU internal APIs
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This workaround was put in dcn2 DMLv1, and now we need it in DMLv2.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fix the programming of DCHUBBUB_ARB_REFCYC_PER_TRIP_TO_MEMORY_A.
Was not filled in.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are currently incorrectly processing avoid split at highest
voltage level.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In Hybrid Graphics, dcn2_1_soc struct stays alive through PnP.
This causes an issue on dc init where dcn2_1_soc which has been
updated by update_bw_bounding_box gets put into dml->soc.
As update_bw_bounding_box is currently incorrect for dcn2.1,
this makes dml calculations fail due to incorrect parameters,
leading to a crash on PnP.
[How]
Comment out update_bw_bounding_box call for now.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We want to use maximum space on display to show source
[how]
For Centered Mode: Replicate source as many times as possible to use
maximum of display active space add borders.
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Signal is update to EDP when driver disable first encoder. The
following encoder using SIGNAL_TYPE_EDP to handle other
device. When encoder signal is HDMI, driver will detect it is dp
and release phy. It cause hw hang.
[How]
Take signal type from link->connector_signal.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
* Clk Mgr DTO update point did not cover all needed updates, as it included a
check for plane_state which does not exist yet when the updater is called on
driver startup
* This resulted in another update path in the pipe programming sequence, based
on a dppclk update flag
* However, this alternate path allowed for stray DTO updates, some of which would
occur in the wrong order during dppclk lowering and cause underflow
[How]
* Remove plane_state check and use of plane_res.dpp->inst, getting rid
of sequence dependencies (this results in extra dto programming for unused
pipes but that doesn't cause issues and is a small cost)
* Allow DTOs to be updated even if global clock is equal, to account for
edge case exposed by diags tests
* Remove update_dpp_dto call in pipe programming sequence (leave update to
dppclk_control there, as that update is necessary and shouldn't occur in clk
mgr)
* Remove call to optimize_bandwidth when committing state, as it is not needed
and resulted in sporadic underflows even with other fixes in place
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
BT.2390 EETF is used for tone mapping/range reduction.
Say display is 0.1 - 500 nits.
The problematic case is when content is 0-400. We apply EETF because
0<0.1 so we need to reduce the range by 0.1.
In the commit, we ignore the bottom range. Most displays map 0 to min and
then have a ramp to 0.1, so sending 0.1 is actually >0.1.
Furthermode, HW that uses 3D LUT also assumes min=0.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU does not keep the wm table across S3, S4, need to re-send
the table. Also defer sending the cable to after DCN bave initialized
[How]
Send table at end of init hw
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A display that supports DRR can never really be considered
"synchronized" with any other display because we can dynamically
enable DRR (i.e. without modeset). this will cause their
relative CRTC positions to drift and lose sync. this will disrupt
features such as MCLK switching that assume and depend on
their permanent alignment (that can only change with modeset)
[how]
check for ignore_msa in stream when considered synchronizability
this ignore_msa is basically actually implemented as "supports drr"
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When aux engine acquire fails, we missed populating the operation_result
that describes the failure reason.
[How]
Set operation_result to new type:
AUX_CHANNEL_OPERATION_FAILED_ENGINE_ACQUIRE
in the case aux engine acquire has failed.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
force_single_disp_pipe_split is a debug flag for use on DCN1
but isn't necessary otherwise as DCN2+ splits by default
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
i2c_read is called to differentiate passive DP->HDMI and DP->DVI-D dongles
The call is expected to fail in DVI-D case but pass in HDMI case
Some HDMI dongles have a chance to fail as well, causing misdetection as DVI-D
[HOW]
Retry i2c_read to ensure failed result is valid
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The enum value for TRANSMITTER_UNIPHY_G is 9. In resource dc_xx_resource
file structure link_enc_regs[], the TRANSMITTER_UNIPHY_G registers are
initialized at index 6. Due to this mismatch, if monitor is attached to
port using TRANSMITTER_UNIPHY_G then the monitor blanks out.
[How]
add function map_transmitter_id_to_phy_instance() and use the function
to map enum transmitter to link regs.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
SLT tests require that diag can drive eDP even if nothing is connected, this is not
typical production use case, so we need to add flag
[how]
add flag, and this flag supercedes "should destroy" logic
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are specific to dcn21 and should not be increased for
reuse on other asics.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
vm should be enabled by default for rn to get
right dml.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There's a use case for inverted gamma
and it's been confirmed that negative slopes are ok.
[how]
Remove code for blocking non-monotonically increasing gamma
Signed-off-by: Aidan Yang <Aidan.Yang@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV12 has lower min dcfclk
[How]
Add update in update_bounding_box
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some systems, we need to check the dcn version in runtime
system, not in compile time.
[How]
Stub in dcn version parameter to find_first_free_audio
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DML is incorrectly initialized with 4 pipes on 3 pipe configs
RequiredDPPCLK is halved on unsplit pipe due to an incorrectly handled 3 pipe
case, causing underflow with 2 planes & pipe split (MPO, 8K + 2nd display)
[HOW]
Set correct number of DPP/OTGs for dml init to generate correct DPP topology
Double RequiredDPPCLK after clock is halved for pipe split
and find_secondary_pipe fails to fix underflow
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This value will be needed by dml and therefore should be externally
accessible.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
One of odm variables was not initialized in dml.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Split a large function into smaller, reusable chunks.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In diags environment we are not programming the DPP DTO
correctly.
[How]
Populate the dpp refclk in dccg so it can be used to correctly
program DPP DTO.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR (Panel Self-Refresh) is a power-saving feature for eDP panels.
The feature has support in DMCU (Display MicroController Unit).
DMCU/driver communication is implemented in DC.
DM can use existing DC PSR interface to use PSR feature.
[How]
- Read psr caps via dpcd
- Send vsc infoframe if panel supports psr
- Disable psr before h/w programming (FULL_UPDATE)
- Enable psr after h/w programming
- Disable psr for fb console
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For upcoming PSR stupport it's useful to have debug entry
to verify psr state.
[How]
- Enable psr dc api for Linux
- Add psr_state file to eDP connector debugfs
usage e.g.: cat /sys/kernel/debug/dri/0/DP-1/psr_state
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit hints are unnecessary after front end programming redesign.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For loop below the assert already checks for the number of instances to
create. ASSERT is meaningless and causing spam.
[How]
dd
Signed-off-by: Jordan Lazare <Jordan.Lazare@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Optimized gamma22 assumes fixed point distribution which is not true
for eetf true.
[how]
Use long calculation for eetf.
Signed-off-by: Aidan Yang <Aidan.Yang@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System hang during S0i3 if DP only connected due to clk is disabled when
doing link training.
During S0i3, clk is disabled while the clk state is updated when ini_hw
called, and at the moment clk is still disabled which indicating a wrong
state for next time trying to enable clk.
[How]
Add an unknown state and initialize it during int_hw, make sure enable clk
command be sent to smu.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Hard to determine if pipe combine is done with MPC or ODM
[how]
Add new visual confirm type, this will mark each MPCC tree
with a different color
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While setting hdmi_vic, hv_frame.vic is not initialized and might
assign a wrong value to hdmi_vic. Cause to send out VSIF with
abnormal value.
[How]
Initialize hv_frame and avi_frame
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're leaking memory by not freeing the gamma used to calculate the
transfer function for legacy gamma.
[How]
Release the gamma after we're done with it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This patch is for fixing Navi14 HDMI display pink screen issue.
[How]
Call stream->link->link_enc->funcs->setup twice. This is setting
the DIG_MODE to the correct value after having been overridden by
the call to transmitter control.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-next-5.5-2019-10-09:
amdgpu:
- Additional RAS enablement for vega20
- RAS page retirement and bad page storage in EEPROM
- No GPU reset with unrecoverable RAS errors
- Reserve vram for page tables rather than trying to evict
- Fix issues with GPU reset and xgmi hives
- DC i2c over aux fixes
- Direct submission for clears, PTE/PDE updates
- Improvements to help support recoverable GPU page faults
- Silence harmless SAD block messages
- Clean up code for creating a bo at a fixed location
- Initial DC HDCP support
- Lots of documentation fixes
- GPU reset for renoir
- Add IH clockgating support for soc15 asics
- Powerplay improvements
- DC MST cleanups
- Add support for MSI-X
- Misc cleanups and bug fixes
amdkfd:
- Query KFD device info by asic type rather than pci ids
- Add navi14 support
- Add renoir support
- Add navi12 support
- gfx10 trap handler improvements
- pasid cleanups
- Check against device cgroup
ttm:
- Return -EBUSY with pipelining with no_gpu_wait
radeon:
- Silence harmless SAD block messages
device_cgroup:
- Export devcgroup_check_permission
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010041713.3412-1-alexander.deucher@amd.com
This allows blocking for BOs to become available
in the memory management.
Amdgpu is doing this for quite a while now during CS. Now
apply the new behavior to all drivers using TTM.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/332878/
Finally! For a very long time, our MST helpers have had one very
annoying issue: They don't know how to reprobe the topology state when
coming out of suspend. This means that if a user has a machine connected
to an MST topology and decides to suspend their machine, we lose all
topology changes that happened during that period. That can be a big
problem if the machine was connected to a different topology on the same
port before resuming, as we won't bother reprobing any of the ports and
likely cause the user's monitors not to come back up as expected.
So, we start fixing this by teaching our MST helpers how to reprobe the
link addresses of each connected topology when resuming. As it turns
out, the behavior that we want here is identical to the behavior we want
when initially probing a newly connected MST topology, with a couple of
important differences:
- We need to be more careful about handling the potential races between
events from the MST hub that could change the topology state as we're
performing the link address reprobe
- We need to be more careful about handling unlikely state changes on
ports - such as an input port turning into an output port, something
that would be far more likely to happen in situations like the MST hub
we're connected to being changed while we're suspend
Both of which have been solved by previous commits. That leaves one
requirement:
- We need to prune any MST ports in our in-memory topology state that
were present when suspending, but have not appeared in the post-resume
link address response from their parent branch device
Which we can now handle in this commit by modifying
drm_dp_send_link_address(). We then introduce suspend/resume reprobing
by introducing drm_dp_mst_topology_mgr_invalidate_mstb(), which we call
in drm_dp_mst_topology_mgr_suspend() to traverse the in-memory topology
state to indicate that each mstb needs it's link address resent and PBN
resources reprobed.
On resume, we start back up &mgr->work and have it reprobe the topology
in the same way we would on a hotplug, removing any leftover ports that
no longer appear in the topology state.
Changes since v4:
* Split indenting changes in drm_dp_mst_topology_mgr_resume() into a
separate patch
* Only fire hotplugs when something has actually changed after a link
address probe
* Don't try to change port->connector at all on ports, just throw out
ports that need their connectors removed to make things easier.
Cc: Juston Li <juston.li@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191022023641.8026-14-lyude@redhat.com
Since we're going to be reprobing the entire topology state on resume
now using sideband transactions, we need to ensure that we actually have
short HPD irqs enabled before calling drm_dp_mst_topology_mgr_resume().
So, do that.
Changes since v3:
* Fix typo in comments
Cc: Juston Li <juston.li@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191022023641.8026-13-lyude@redhat.com
Currently, every single piece of code in amdgpu that loops through
connectors does it incorrectly and doesn't use the proper list iteration
helpers, drm_connector_list_iter_begin() and
drm_connector_list_iter_end(). Yeesh.
So, do that.
Cc: Juston Li <juston.li@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191022023641.8026-12-lyude@redhat.com
This is a complicated one. Essentially, there's currently a problem in the MST
core that hasn't really caused any issues that we're aware of (emphasis on "that
we're aware of"): locking.
When we go through and probe the link addresses and path resources in a
topology, we hold no locks when updating ports with said information. The
members I'm referring to in particular are:
- ldps
- ddps
- mcs
- pdt
- dpcd_rev
- num_sdp_streams
- num_sdp_stream_sinks
- available_pbn
- input
- connector
Now that we're handling UP requests asynchronously and will be using some of
the struct members mentioned above in atomic modesetting in the future for
features such as PBN validation, this is going to become a lot more important.
As well, the next few commits that prepare us for and introduce suspend/resume
reprobing will also need clear locking in order to prevent from additional
racing hilarities that we never could have hit in the past.
So, let's solve this issue by using &mgr->base.lock, the modesetting
lock which currently only protects &mgr->base.state. This works
perfectly because it allows us to avoid blocking connection_mutex
unnecessarily, and we can grab this in connector detection paths since
it's a ww mutex. We start by having drm_dp_mst_handle_up_req() hold this
when updating ports. For drm_dp_mst_handle_link_address_port() things
are a bit more complicated. As I've learned the hard way, we can grab
&mgr->lock.base for everything except for port->connector. See, our
normal driver probing paths end up generating this rather obvious
lockdep chain:
&drm->mode_config.mutex
-> crtc_ww_class_mutex/crtc_ww_class_acquire
-> &connector->mutex
However, sysfs grabs &drm->mode_config.mutex in order to protect itself
from connector state changing under it. Because this entails grabbing
kn->count, e.g. the lock that the kernel provides for protecting sysfs
contexts, we end up grabbing kn->count followed by
&drm->mode_config.mutex. This ends up creating an extremely rude chain:
&kn->count
-> &drm->mode_config.mutex
-> crtc_ww_class_mutex/crtc_ww_class_acquire
-> &connector->mutex
I mean, look at that thing! It's just evil!!! This gross thing ends up
making any calls to drm_connector_register()/drm_connector_unregister()
impossible when holding any kind of modesetting lock. This is annoying
because ideally, we always want to ensure that
drm_dp_mst_port->connector never changes when doing an atomic commit or
check that would affect the atomic topology state so that it can
reliably and easily be used from future DRM DP MST helpers to assist
with tasks such as scanning through the current VCPI allocations and
adding connectors which need to have their allocations updated in
response to a bandwidth change or the like.
Being able to hold &mgr->base.lock throughout the entire link probe
process would have been _great_, since we could prevent userspace from
ever seeing any states in-between individual port changes and as a
result likely end up with a much faster probe and more consistent
results from said probes. But without some rework of how we handle
connector probing in sysfs it's not at all currently possible. In the
future, maybe we can try using the sysfs locks to protect updates to
connector probing state and fix this mess.
So for now, to protect everything other than port->connector under
&mgr->base.lock and ensure that we still have the guarantee that atomic
check/commit contexts will never see port->connector change we use a
silly trick. See: port->connector only needs to change in order to
ensure that input ports (see the MST spec) never have a ghost connector
associated with them. But, there's nothing stopping us from simply
throwing the entire port out and creating a new one in order to maintain
that requirement while still keeping port->connector consistent across
the lifetime of the port in atomic check/commit contexts. For all
intended purposes this works fine, as we validate ports in any contexts
we care about before using them and as such will end up reporting the
connector as disconnected until it's port's destruction finalizes. So,
we just do that in cases where we detect port->input has transitioned
from true->false. We don't need to worry about the other direction,
since a port without a connector isn't visible to userspace and as such
doesn't need to be protected by &mgr->base.lock until we finish
registering a connector for it.
For updating members of drm_dp_mst_port other than port->connector, we
simply grab &mgr->base.lock in drm_dp_mst_link_probe_work() for already
registered ports, update said members and drop the lock before
potentially registering a connector and probing the link address of it's
children.
Finally, we modify drm_dp_mst_detect_port() to take a modesetting lock
acquisition context in order to acquire &mgr->base.lock under
&connection_mutex and convert all it's users over to using the
.detect_ctx probe hooks.
With that, we finally have well defined locking.
Changes since v4:
* Get rid of port->mutex, stop using connection_mutex and just use our own
modesetting lock - mgr->base.lock. Also, add a probe_lock that comes
before this patch.
* Just throw out ports that get changed from an output to an input, and
replace them with new ports. This lets us ensure that modesetting
contexts never see port->connector go from having a connector to being
NULL.
* Write an extremely detailed explanation of what problems this is
trying to fix, since there's a _lot_ of context here and I honestly
forgot some of it myself a couple times.
* Don't grab mgr->lock when reading port->mstb in
drm_dp_mst_handle_link_address_port(). It's not needed.
Cc: Juston Li <juston.li@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191022023641.8026-7-lyude@redhat.com
Fix sparse warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:746:6:
warning: symbol 'dc_link_detect_helper' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds handling of dp is usb-c, it is not tested but is
needed to support dp over usb-c
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use requested_dispclk_khz / 1000 directly
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU fixed this issue after version 0x370c00
[How]
enable smu send message to set dcfclk after smu version 0x370c00
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Should always MP0_BASE for any register definition from MP per-IP header files.
I belive the reason the linux version of MP1_BASE works is The 0th element of the 0th table
of that is identical to the corrisponding value of MP0_BASE in the renoir offset header file.
The reason we should only use MP0_BASE is There is only one set of per-IP headers MP
that includes all register definitions related to SMU IP block. This IP includes MP0, MP1, MP2
and an ecryption engine that can be used only by MP0. As a result all register definitions from
MP file should be based only on MP0_BASE data.
[How]
Change MP1_BASE to MP0_BASE
Signed-off-by: joseph gravenor <joseph.gravenor@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Handle the case where we don't get a valid table. Also fixes compiler
warning for variable potentially used before assignment.
[How]
If the entire table has no valid fclk, reject the table and use our own
hard code.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
dprefclk is improperly read due to incorrect units used.
Causes an audio clock to be improperly set, making audio
non-functional and videos play back too fast
[HOW]
Scale dprefclk value from MHz to KHz (multiply by 1000)
to ensure that dprefclk_khz is in correct units
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Handle 18 DecimalBPP like other cases
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previously 8k30 worked with dsc and odm combine due to a workaround that ran
the formula a second time with dsc support enable should dsc validation fail.
This worked when clocks were low enough for formula to enable odm to lower
voltage, however now broke due to increased clocks.
This change updates the ODM combine policy within the formula to properly
reflect our current policy within DC, only enabling ODM when we have to, as
well as adding a check for viewport width when dsc is enabled.
As a side effect the redundant call to dml when odm is required is now
unnecessary.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously only dummy functions were added in Diags for FPGA.
On silicon, this would lead to a segmentation fault on silicon diags.
[How]
Check if diags silicon and if so, add dummy functions.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DPM level is 8 these were incorrect before. Fix them
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The values for bounding box and res_caps were incorrect. So
Fix them
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
use dcn20 common regs define to share some regs with dcn20
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Detile buffer size affects dcc caps, it was already added for
dcn2. Now add it for dcn21
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1 vmid limitation only exists for HOSTVM which is a custom
use case anyway.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Renoir is gfx9, same as dcn10, not dcn20.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Renoir can use vm contexes as long as HOSTVM is off so
this should be initialized.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Watermarks not propagated to DCHUBP after it is powered on
[How]
Add temoprary function apply_DEDCN21_147_wa to apply wm settings for Renoir
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Incorrect page table address and programming sys aperture for
stutter gather, so fix it.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enabling hostvm when ROIMMU is not active seems to break GPUVM.
This fixes the issue by not enabling hostvm if ROIMMU is not
activated.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
driver updateis the dcn2_1_soc into dml before call update_bw_bounding_box
[How]
Move the patch function before calculate wm.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Signed-off-by: joseph graveno <joseph.gravenor@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
it allows us to do urgent latency programming
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN20 and DCN21 have different phy programming sequences.
[How]
Create a separate dcn21_link_encoder for Renoir
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds renoir hw_seq, needed to do renoir
specific hw programing
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Earlier changes to support configurable aux timeout
caused dc init failure on vega due to missing reg defs.
Needs to be disabled until implemented for vega.
[How]
Set extended aux timeout cap for vega to false.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-By: abdoulaye berthe <abdoulaye.berthe@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1-add configurable timeout support to aux engine.
2-add timeout support field to dc_caps
3-add reg_key to override extended timeout support
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1-add timeout length and multiplier fields to aux_control1 register
2-update access mechanism from macro constructed name to uint32_t
defined addresses.
3-define registers and field per asic family
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when CONFIG_DRM_AMD_DC_DCN2_1 is not enable in .config,
there is build error. struct dpm_clocks shoud not be
guarded.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
enable dc get dmp clock table and set dcn watermarks
via pplib.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
there are two paths for renoir dc access smu.
one dc access smu directly using bios smc
interface: set disply, dprefclk, etc.
another goes through pplib for get dpm clock
table and set watermmark.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the dcn21 functions in dcn21_resource.c and make the
dcn20 functions static since they are only used in
dcn20_resource now.
Cc: bhawanpreet.lakha@amd.com
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mostly a cocci-job, but it flat out refused to remove the
declaration in drivers/gpu/drm/amd/display/dc/core/dc.c so
had to do that part manually.
@swap@
identifier TEMP;
expression A,B;
@@
- TEMP = A;
- A = B;
- B = TEMP;
+ swap(A, B);
@@
type T;
identifier swap.TEMP;
@@
(
- T TEMP;
|
- T TEMP = {...};
)
... when != TEMP
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Doing this allows us to split it for diffrent asics. This design will
be helpful for future Asciis.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously SMU was giving us 0s for the clock table. Now they have valid
clock table. We should use theirs. Also, need to send SMU watermark
ranges for selecting optimal watermarks.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Without a check for virtual links, every link's DIG was getting
checked for enabled or disabled. If link was virtual, since it
did not have a DIG, this would cause issues.
[HOW]
Skip DIG Enable check if link is virtual and add virtual link to
to display count.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDMI 2.0 requires scrambling under specific conditions. We refer to
stream property LTE_340MCSC_SCRAMBLE to determine whether en/dis
scrambling.
While creating stream for sink, we setup LTE_340MCSC_SCRAMBLE by
referring to edid_caps. However, dm_helpers_parse_edid_caps()
doesn't construct HDMI Forum block data for edid_caps.
Moreover, fill_stream_properties_from_drm_display_mode() aslo
unconsciously clear the LTE_340MCSC_SCRAMBLE flag.
[How]
Drm already provides drm_display_info to refer HDMI Forum vsdb info.
Set stream LTE_340MCSC_SCRAMBLE by drm_display_info and remove
memset in fill_stream_properties_from_drm_display_mode()
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
During detection:
function: get_active_converter_info populates link->dpcd_caps.dongle_caps
only when dpcd_rev >= DPCD_REV_11 and DWN_STRM_PORTX_TYPE is
DOWN_STREAM_DETAILED_HDMI or DOWN_STREAM_DETAILED_DP_PLUS_PLUS.
Otherwise, it is not cleared, and stale information remains.
During mode validation:
function: dp_active_dongle_validate_timing reads
link->dpcd_caps.dongle_caps->dongle_type to determine the maximum
pixel clock to support. This information is now stale and no longer
valid.
[HOW]
dp_active_dongle_validate_timing should be using
link->dpcd_caps->dongle_type instead.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Static ramp to max refresh rate does not have capability check on
calculated v_total. Programming a lower v_total_min and max than the
total causes continuous spurious HPDs.
[How]
Add a capability check after v_total calculation similar to calculate
v_total helper functions.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
1. defer delay and sw start delay has been mixed up, defer delay was
programmed to AUX_SW_CONTROL:AUX_SW_START_DELAY.
2. There's no delay for defer
[how]
1. Set aux sw start to 0
2. Add delay for defer scenario
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
use vbios message to call smu for dpm level
also only program dmdata in vsyncflip as HW requirement.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Compiling with GCC 9.1.0 gives the following warning (I have
warnings-as-errors enabled):
drivers/gpu/drm/amd/amdgpu/../dal-dev/dc/core/dc.c: In function 'dc_validate_seamless_boot_timing':
drivers/gpu/drm/amd/amdgpu/../dal-dev/dc/core/dc.c:1180:8: error: 'se' may be used uninitialized in this function [-Werror=maybe-uninitialized]
1180 | if (!se->funcs->dp_get_pixel_format(
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1181 | se,
| ~~~
1182 | &hw_crtc_timing.pixel_encoding,
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1183 | &hw_crtc_timing.display_color_depth))
[How]
Initialize se to NULL.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
we found using an active DP to HDMI panel that we weren't validating
dp_pixel_format and hardware timing v_front_porch, causing screen to
blank and/or corrupt while attempting a seamless boot.
[how]
added checks during dc_validate_seamless_boot_timing for these values
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Dongle 0x00E04C power down all internal circuits including
AUX communication preventing reading DPCD table.
Encoder will skip DP RX power down on disable output
to keep receiver powered all the time.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Number of audio endpoints wasn't updated from dcn20's 6 when created
[HOW]
Changed num_audio to 4 to match the correct sbios value
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dp_48m_refclk_driver_pwdn is persistent through S3 and S5.
This was worked arround in SMU FW 55.21.0. Earlier FW don't have this fix
so we will hang on reboot
[how]
add a guard for smu versions before SMU FW 55.21.0
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The SMU message to enable this feature looks at argument. Previous code
didn't send right argument. This change will allow the feature to be
be enabled.
[How]
Fixed one issue where SMU message to enable the feature was sent without
setting the parameter.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If 48mhz refclk is turned off during PSR, we will have issue doing
link training during detection.
[How]
Get out of PSR before detection
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When diags adds a DWB via a stream update, we calculate MMHUBBUB
paramaters, but dc->current_state has not yet been updated
when the DWB programming happens. This leads to overflow on
high bandwidth tests since the incorrect MMHUBBUB arbitration
parameters are programmed.
[How]
Pass the updated context down to the (enable|update)_writeback functions
so that they can use the correct watermarks when programming MMHUBBUB.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
dpp2_get_optimal_number_of_taps is incorrect, and dcn2 should be using
dpp1_get_optimal_number_of_taps instead
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a bug when determining if link training should be retried when
HPD is low in dp_verify_link_cap_with_retries.
[How]
Correctly, fail dp_verify_link_cap_with_retries without retry when
HPD is low.
Signed-off-by: Sivapiriyan Kumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the driver sends a pipe set command to the DMCU FW, it does not wait
for the command to complete. This can lead to unpredictable behavior if,
for example, the driver were to request a pipe disable to the FW via MCP,
then power down some hardware before the firmware has completed processing
the command.
[How]
Wait for the DMCU FW to finish processing set pipe commands
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Output bitrate was mistakenly left out, causing corruption on some
DSC low resolution (such as 800x600) modes.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some displays rely on the SPD verticle frequency maximum value.
Must round the calculated refresh rate to the nearest integer.
[How]
Round the nominal calculated refresh rate to the nearest whole
integer.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This function was mistakenly reverted as part of a legitimate revert. The
old version that was reverted to has bad logic, and is causing situations
where p-state change support is being toggled when it shouldn't be,
resulting in hangs.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Type-c PHY config is not align with dpcd lane count.
When those values didn't match, it cause driver do
link training with 4 lane but phy only can output 2 lane.
The link trainig always fail.
[How]
1. Modify get_max_link_cap function. According DPALT_DP4
to update max lane count.
2. Add dp_mst_verify_link_cap to handle MST case because
we didn't call dp_mst_verify_link_cap for MST case.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Didn't send VSIF infopacket when it's 4k mode defined in HDMI 1.4b.
For HDMI 1.4b, While displaying 4k modes, it should send VSP.
[How]
Call mod_build_hf_vsif_infopacket() function to build info frame
and send it.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The register CM_TEST_DEBUG_DATA is used in dpp1_program_input_csc, which is
called from dpp2_cnv_setup, but the shifts and masks for the fields of that
register are not initialized for dcn2. This causes all reads of that register
to return 0.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
memcmp is vulnerable to regression due to dc_clocks structures not being
organized properly (not "current" clock related structures being at the beginning
of the structure) and causes unnecessary setting of the optimize bit
[how]
add a dcn sepcific comparator, implement for dcn2
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The vendor specific infoframe is needed for HDMI while displaying
specific modes.
DC supports sending it, but we aren't currently building it
[How]
Add mod_build_hf_vsif_infopacket() to build the vendor specific
info packet.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HPD is not suppressed when we lower
clocks on renoir. B/c of this we do link
training when the 48mhz refclk is off, which
will cause ASIC hang.
[how]
Exit optimized power state for detection purpose.
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently pipe split may steal an existing ODM pipe depending on stream
sequence. This change prevents that from happening as easily.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Gary Kattan <Gary.Kattan@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When planes are added or removed from a stream, the change
in pipe usage from dynamic MPC combine can cause a second
stream using ODM combine to pick a different pipe to combine with.
In this scenario, a different OPP is connected to the ODM without
programming its FMT.
[How]
Reprogram the FMT in dcn20_program_pipe whenever a pipe is
newly enabled, or when its opp changes.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If VSTARTUP changes due to bandwidth requirements, we must
recalculate and update VLINE2 as well for proper flip reporting.
[How]
After all calls to program_global_sync which reconfigures
VSTARTUP, also make sure to update V_UPDATE (i.e. VLINE2 on DCNx).
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A recent bug showed that logging would be useful in debugging
various gamma issues.
[How]
Fix formatting for easier graphing.
Prevent performance hit when doing diag.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Virtual signal means there is no display attached.
In this case we will assign a virtual signal type to the stream.
We should only enable the front end of the stream but not the back end.
[how]
When stream is enabling with virtual signal type, skip backend programming.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While displaying 4k modes defined in HDMI1.4b, should set VIC to 0
and use VSP HDMI_VIC to indicate the mode.
[How]
Use functions defined in drm to set up the VIC correspondingly.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To compare the crc of the framebuffer data at input of
display pipeline with the crc of the otg, we need to
disable pixel formatter's dynamic expansion feature during
crc capture and keep it enable in the normal operation.
[HOW]
Expose a new interface in DM and dc for pixel formatter
(fmt dynamic bitdepth expansion control). Interface control
the FMT_DYNAMIC_EXP_EN bit, during crc capture keep
it disabled.
Signed-off-by: Robin Singh <robin.singh@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
-Colorspace: Expose different prop values for DP vs. HDMI (Gwan-gyeong Mun)
-fourcc: Add DRM_FORMAT_MOD_ARM_16X16_BLOCK_U_INTERLEAVED (Raymond)
-not_actually: s/ENOTSUPP/EOPNOTSUPP/ in drm_edid and drm_mipi_dbi. This should
not reach userspace, but adding here to specifically call that out (Daniel)
-i810: Prevent underflow in dispatch ioctls (Dan)
-komeda: Add ACLK sysfs attribute (Mihail)
-v3d: Allow userspace to clean up after render jobs (Iago)
Cross-subsystem Changes:
-MAINTAINERS:
-Add Alyssa & Steven as panfrost reviewers (Rob)
-Add Jernej as DE2 reviewer (Maxime)
-Add Chen-Yu as Allwinner maintainer (Maxime)
-staging: Make some stack arrays static const (Colin)
Core Changes:
-ttm: Allow drivers to specify their vma manager (to use gem mgr) (Gerd)
-docs: Various fixes in connector/encoder/bridge docs (Daniel, Lyude, Laurent)
-connector: Allow more than 3 possible encoders for a connector (José)
-dp_cec: Allow a connector to be associated with a cec device (Dariusz)
-various: Fix some compile/sparse warnings (Ville)
-mm: Ensure mm node removals are properly serialised (Chris)
-panel: Specify the type of panel for drm_panels for later use (Laurent)
-panel: Use drm_panel_init to init device and funcs (Laurent)
-mst: Refactors and cleanups in anticipation of suspend/resume support (Lyude)
-vram:
-Add lazy unmapping for gem bo's (Thomas)
-Unify and rationalize vram mm and gem vram (Thomas)
-Expose vmap and vunmap for gem vram objects (Thomas)
-Allow objects to be pinned at the top of vram to avoid fragmentation (Thomas)
Driver Changes:
-various: Include drm_bridge.h instead of relying on drm_crtc.h (Boris)
-ast/mgag200: Refactor show_cursor(), move cursor to top of video mem (Thomas)
-komeda:
-Add error event printing (behind CONFIG) and reg dump support (Lowry)
-Add suspend/resume support (Lowry)
-Workaround D71 shadow registers not flushing on disable (Lowry)
-meson: Add suspend/resume support (Neil)
-omap: Miscellaneous refactors and improvements (Tomi/Jyri)
-panfrost/shmem: Silence lockdep by using mutex_trylock (Rob)
-panfrost: Miscellaneous small fixes (Rob/Steven)
-sti: Fix warnings (Benjamin/Linus)
-sun4i:
-Add vcc-dsi regulator to sun6i_mipi_dsi (Jagan)
-A few patches to figure out the DRQ/start delay calc on dsi (Jagan/Icenowy)
-virtio:
-Add module param to switch resource reuse workaround on/off (Gerd)
-Avoid calling vmexit while holding spinlock (Gerd)
-Use gem shmem helpers instead of ttm (Gerd)
-Accommodate command buffer allocations too big for cma (David)
Cc: Rob Herring <robh@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Raymond Smith <raymond.smith@arm.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mihail Atanassov <Mihail.Atanassov@arm.com>
Cc: Lowry Li <Lowry.Li@arm.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Iago Toral Quiroga <itoral@igalia.com>
Cc: David Riley <davidriley@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHF6rntfJ3enn8gh8cywAJXLcr3kFAl2d9h8ACgkQcywAJXLc
r3ms5gf9HIFpqwJ16CqaRukSnpcBcDoYUM8DGrOic+vw2bw14BQwFqvEOqrCkKL4
V6h/OCJlNFPtOcc1LvU/jeXxYf4AQWh/2qZeg+oee7HAGX5x8Y3f08GsEjO8+55t
QvSVxCKVti04M1ErPRfKrM7KPVE+IC+KdY26nO8Bf5zDGeCAkiPIDrdh2aZGMRdC
Eer0DJ96cgWW9LrhseCdj5nKwcR78DlbWa79zuPAss4LaBBbXqThNXYYzg/mZMKB
+VYgzs48tGYKK1NXXJ6biVI3brHrM52bqv5JpIncD5HepF1oIartWOMnbAO7MAqh
h/tgJWxL+4bnl9aqY87by1BtyVgl3w==
=kaOE
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-10-09-2' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.5:
UAPI Changes:
-Colorspace: Expose different prop values for DP vs. HDMI (Gwan-gyeong Mun)
-fourcc: Add DRM_FORMAT_MOD_ARM_16X16_BLOCK_U_INTERLEAVED (Raymond)
-not_actually: s/ENOTSUPP/EOPNOTSUPP/ in drm_edid and drm_mipi_dbi. This should
not reach userspace, but adding here to specifically call that out (Daniel)
-i810: Prevent underflow in dispatch ioctls (Dan)
-komeda: Add ACLK sysfs attribute (Mihail)
-v3d: Allow userspace to clean up after render jobs (Iago)
Cross-subsystem Changes:
-MAINTAINERS:
-Add Alyssa & Steven as panfrost reviewers (Rob)
-Add Jernej as DE2 reviewer (Maxime)
-Add Chen-Yu as Allwinner maintainer (Maxime)
-staging: Make some stack arrays static const (Colin)
Core Changes:
-ttm: Allow drivers to specify their vma manager (to use gem mgr) (Gerd)
-docs: Various fixes in connector/encoder/bridge docs (Daniel, Lyude, Laurent)
-connector: Allow more than 3 possible encoders for a connector (José)
-dp_cec: Allow a connector to be associated with a cec device (Dariusz)
-various: Fix some compile/sparse warnings (Ville)
-mm: Ensure mm node removals are properly serialised (Chris)
-panel: Specify the type of panel for drm_panels for later use (Laurent)
-panel: Use drm_panel_init to init device and funcs (Laurent)
-mst: Refactors and cleanups in anticipation of suspend/resume support (Lyude)
-vram:
-Add lazy unmapping for gem bo's (Thomas)
-Unify and rationalize vram mm and gem vram (Thomas)
-Expose vmap and vunmap for gem vram objects (Thomas)
-Allow objects to be pinned at the top of vram to avoid fragmentation (Thomas)
Driver Changes:
-various: Include drm_bridge.h instead of relying on drm_crtc.h (Boris)
-ast/mgag200: Refactor show_cursor(), move cursor to top of video mem (Thomas)
-komeda:
-Add error event printing (behind CONFIG) and reg dump support (Lowry)
-Add suspend/resume support (Lowry)
-Workaround D71 shadow registers not flushing on disable (Lowry)
-meson: Add suspend/resume support (Neil)
-omap: Miscellaneous refactors and improvements (Tomi/Jyri)
-panfrost/shmem: Silence lockdep by using mutex_trylock (Rob)
-panfrost: Miscellaneous small fixes (Rob/Steven)
-sti: Fix warnings (Benjamin/Linus)
-sun4i:
-Add vcc-dsi regulator to sun6i_mipi_dsi (Jagan)
-A few patches to figure out the DRQ/start delay calc on dsi (Jagan/Icenowy)
-virtio:
-Add module param to switch resource reuse workaround on/off (Gerd)
-Avoid calling vmexit while holding spinlock (Gerd)
-Use gem shmem helpers instead of ttm (Gerd)
-Accommodate command buffer allocations too big for cma (David)
Cc: Rob Herring <robh@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Raymond Smith <raymond.smith@arm.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mihail Atanassov <Mihail.Atanassov@arm.com>
Cc: Lowry Li <Lowry.Li@arm.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Iago Toral Quiroga <itoral@igalia.com>
Cc: David Riley <davidriley@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 10 Oct 2019 01:00:47 AM AEST
# gpg: using RSA key 732C002572DCAF79
# gpg: Can't check signature: public key not found
# Conflicts:
# drivers/gpu/drm/i915/gem/i915_gem_execbuffer.c
# drivers/gpu/drm/i915/i915_drv.c
# drivers/gpu/drm/i915/i915_gem.c
# drivers/gpu/drm/i915/i915_gem_gtt.c
# drivers/gpu/drm/i915/i915_vma.c
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009150825.GA227673@art_vandelay
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c: In function dce110_enable_audio_stream:
drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c:949:23: warning: variable pp_smu set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c: In function dce110_disable_audio_stream:
drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c:983:23: warning: variable pp_smu set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c: In function dce110_program_front_end_for_pipe:
drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c:2429:19: warning: variable old_pipe set but not used [-Wunused-but-set-variable]
'pp_smu' is not used since commit 170a2398d2 ("drm/amd/display:
make clk_mgr call enable_pme_wa")
'old_pipe' is not used since commit 65d38262b3 ("drm/amd/display:
fbc state could not reach while enable fbc")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dpp.c: In function dpp2_get_optimal_number_of_taps:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dpp.c:359:11: warning: variable pixel_width set but not used [-Wunused-but-set-variable]
It is not used since commit f7de96ee8b ("drm/amd/display:
Add DCN2 DPP")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dwb_scl.c: In function dwb_program_horz_scalar:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dwb_scl.c:725:11: warning: variable h_ratio_chroma set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dwb_scl.c: In function dwb_program_vert_scalar:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dwb_scl.c:806:11: warning: variable v_ratio_chroma set but not used [-Wunused-but-set-variable]
They are not used since commit 345429a67c ("drm/amd/display:
Add DCN2 DWB")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/dsc/rc_calc.c: In function calc_rc_params:
drivers/gpu/drm/amd/display/dc/dsc/rc_calc.c:180:6: warning: variable source_bpp set but not used [-Wunused-but-set-variable]
It is not used since commit 97bda0322b ("drm/amd/display:
Add DSC support for Navi (v2)")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix sparse warnings:
drivers/gpu/drm/amd/display/dc/core/dc_link.c:687:6: warning: symbol 'wait_for_alt_mode' was not declared. Should it be static?
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
rivers/gpu/drm/amd/amdgpu/../display/modules/freesync/freesync.c:
In function mod_freesync_get_settings:
drivers/gpu/drm/amd/amdgpu/../display/modules/freesync/freesync.c:984:24:
warning: variable core_freesync set but not used [-Wunused-but-set-variable]
It is not used since commit 98e6436d3a ("drm/amd/display: Refactor FreeSync module")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
p and g are switched in 'amdpgu_dm'
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix sparse warnings:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_hdcp.c:32:6: warning: symbol 'lp_write_i2c' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_hdcp.c:42:6: warning: symbol 'lp_read_i2c' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_hdcp.c:52:6: warning: symbol 'lp_write_dpcd' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_hdcp.c:59:6: warning: symbol 'lp_read_dpcd' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in the macros H1_A45_AUTHENICATED and
D1_A4_AUTHENICATED, fix these by adding the missing T.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We haven't done any backmerge for a while due to the merge window, and it
starts to become an issue for komeda. Let's bring 5.4-rc1 in.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The type definition for 'uint' clashes with the generic kernel
headers:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn21/display_mode_vba_21.c:43:22: error: redefinition of typedef 'uint' is a C11 feature [-Werror,-Wtypedef-redefinition]
include/linux/types.h:92:23: note: previous definition is here
Just remove this type and use plain 'unsigned int' consistently,
as it is already use almost everywhere in this file.
Fixes: b04641a3f4 ("drm/amd/display: Add Renoir DML")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are supposed to be atomic after all. We'll need this in a moment for
the next commit.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kfree() checks this automatically.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, every single piece of code in amdgpu that loops through
connectors does it incorrectly and doesn't use the proper list iteration
helpers, drm_connector_list_iter_begin() and
drm_connector_list_iter_end(). Yeesh.
So, do that.
Cc: Juston Li <juston.li@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since we're going to be reprobing the entire topology state on resume
now using sideband transactions, we need to ensure that we actually have
short HPD irqs enabled before calling drm_dp_mst_topology_mgr_resume().
So, do that.
Changes since v4:
* Fix typo in comments
Cc: Juston Li <juston.li@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In dcn*_create_resource_pool the allocated memory should be released if
construct pool fails.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's apparently needed in some configurations.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We had a couple of missing definitions and formatting errors.
v2: Fix 'notifying' type
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without CONFIG_DEBUG_FS, we get a warning for an unused
variable:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:6020:33: error: unused variable 'source' [-Werror,-Wunused-variable]
Hide the variable in an #ifdef like its only users.
Fixes: 14b2584636 ("drm/amd/display: add functionality to grab DPRX CRC entries.")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Laptops with AMD APU doesn't restore display backlight brightness after
system resume.
This issue started when DC was introduced.
Let's use BL_CORE_SUSPENDRESUME so the backlight core calls
update_status callback after system resume to restore the backlight
level.
Tested on Dell Inspiron 3180 (Stoney Ridge) and Dell Latitude 5495
(Raven Ridge).
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP is not fully finished, so we need to be able to
build and run the driver without it.
[How]
Add a Kconfig to toggle it
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We don't support HDCP for pre RAVEN asics
[How]
Check if we are RAVEN+. Use this to attach the content_protection
property, this way usermode can't try to enable HDCP on pre DCN asics.
Also we need to update the module on hpd so guard it aswell
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to use HW state to set content protection to ENABLED.
This way we know that the link is encrypted from the HW side
[How]
Create a workqueue that queries the HW every ~2seconds, and sets it to
ENABLED or DESIRED based on the result from the hardware
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This is needed for DP as DP can send us info using irq.
[How]
Check if irq bit is set on short pulse and call the
function that handles cpirq in amdgpu_dm_hdcp
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to manage the content protection property changes for
different usecase, once cp is DESIRED we need to maintain the
ENABLED/DESIRED status for different cases.
[How]
1. Attach the content_protection property
2. HDCP enable (UNDESIRED -> DESIRED)
call into the module with the correct parameters to start
hdcp. Set cp to ENABLED
3. HDCP disable (ENABLED -> UNDESIRED)
Call the module to disable hdcp.
3. Handle Special cases (Hotplug, S3, headless S3, DPMS)
If already ENABLED: set to DESIRED on unplug/suspend/dpms,
and disable hdcp
Then on plugin/resume/dpms: enable HDCP
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need this to enable HDCP on linux, as we need events to interact
with the hdcp module
[How]
Add work queue to display manager and handle the creation and destruction
of the queue
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to read and write specific i2c and dpcd messages.
[How]
Created static functions for packing the dpcd and i2c messages for hdcp.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to interact with the hdcp module from the DM, the module
has to be interacted with in terms of events
[How]
Create the files needed for linux hdcp. These files manage the events
needed for the dm to interact with the hdcp module.
We use the kernel work queue to process the events needed for
the module
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update the hdcp display parameter whenever the link is
updated, so the next time there is an update to hdcp we have the
latest display info
[How]
Create a callback, and use this anytime there is a change in the link. This will
be used later by the dm.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All the HDCP transactions should be verified using PSP.
[How]
This patch calls psp with the correct inputs to verify the steps
of authentication.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This module manages HDCP for amdgpu driver. The module behaves as a
state machine which handles the different authentication states of HDCP
The module is divided into 3 major components
+--------+
| Hdcp.c |
+--------+
Manages the state machine, sends the events to be executed and communicates
with the dm
+-----------+
|Execution.c|
+-----------+
This executes events based on the current state. Also generates
execution results as transition inputs
+------------+
|Transition.c|
+------------+
Decides the next state based on the input and makes requests to
hdcp.c to handle.
+-------------+
------> | Execution.c | ------
| +-------------+ |
| V
+----+ +--------+ +--------------+
| DM | -----> | Hdcp.c | <------------ | Transition.c |
+----+ <----- +--------+ +--------------+
v2: Drop unused function definitions
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There can be some unsynchronized frames when entering/exiting
LFC. This may cause tearing or stuttering at such transitions.
[How]
Add a enter/exit margin to algorithm to smoothly transition into
and out of LFC without desynchronizing frames.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Reza Amini <Reza.Amini@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Detile buffer size affects dcc caps and therefore needs to be
corrected for each ip.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
tg_inst may be used uninitialized, so initialize it to 0.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When more than 2 displays are connected to the graphics card,
only the minimum memory clock is needed. However, when more
displays are connected, the minimum memory clock is not
sufficient enough to support the overwhelming bandwidth.
System will hang under this circumstance.
Also, the old code didn't address HBM cards, which has 2
pseudo channels. We need to add the HBM part here.
[How]
When graphics card connects to 2 or more displays,
switch to high memory clock. Also, choose memory
multiplier based on whether its regular DRAM or HBM.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
seamless boot didn't work for non edp's before
[how]
removed edp-specific code, made dp read uefi-set link settings. Also fixed
a hubbub code line to be consistent with usage of function.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previously 8k30 worked with dsc and odm combine due to a workaround that ran
the formula a second time with dsc support enable should dsc validation fail.
This worked when clocks were low enough for formula to enable odm to lower
voltage, however now broke due to increased clocks.
This change updates the ODM combine policy within the formula to properly
reflect our current policy within DC, only enabling ODM when we have to, as
well as adding a check for viewport width when dsc is enabled.
As a side effect the redundant call to dml when odm is required is now
unnecessary.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Presently, there is no way for clocks to be lowered, only raised.
[HOW]
Compare clock status against previous known clock status, and optimize
if different.
This requires re-ordering the layout of the dc_clocks structure, as the
current ordering allows identical clock states to appear different.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some ODM-related register settings are inconsistently updated by VBIOS, causing
the state in DC to be invalid, which would then end up crashing in certain
use-cases (such as disable/enable device).
[how]
Check the enabled status of the second pipe when determining the number of
OPTC sources. If the second pipe is disabled, set the number of sources to 1
regardless of other settings (that may not be updated correctly).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A lot of the time, the backlight characteristic curve maps min backlight
to a non-zero value.
But there are cases where we want the curve to intersect at 0.
In this scenario even if OS never asks to set 0% backlight, the ABM
reduction can result in backlight being lowered close to 0.
This particularly can cause problems in some LED drivers, and in
general just looks like backlight is completely off.
[How]
Add default cap to disallow backlight from dropping below 1%
even after ABM reduction is applied.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This change was made because DTO programming was double-buffered, which
is itself an issue. After deactivating the DTO double buffer, this
change becomes unnecessary.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When changing DPP global ref clock, DTO adjustments must take effect
immediately, or else underflow may occur.
It appears the original decision to double-buffer DTO adjustments was made to
prevent underflows that occur when raising DPP ref clock (which is not
double-buffered), but that same decision causes similar issues when
lowering DPP global ref clock. The better solution is to order the
adjustments according to whether clocks are being raised or lowered.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Just like all the other variants, this one passes invalid
compile-time options with clang after the new code got
merged:
clang: error: unknown argument: '-mpreferred-stack-boundary=4'
scripts/Makefile.build:265: recipe for target 'drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.o' failed
Use the same variant that we have for dcn20 to fix compilation.
Fixes: eced51f9ba ("drm/amd/display: Add hubp block for Renoir (v2)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without CONFIG_DEBUG_FS, we get a warning for an unused
variable:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:6020:33: error: unused variable 'source' [-Werror,-Wunused-variable]
Hide the variable in an #ifdef like its only users.
Fixes: 14b2584636 ("drm/amd/display: add functionality to grab DPRX CRC entries.")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The type definition for 'uint' clashes with the generic kernel
headers:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn21/display_mode_vba_21.c:43:22: error: redefinition of typedef 'uint' is a C11 feature [-Werror,-Wtypedef-redefinition]
include/linux/types.h:92:23: note: previous definition is here
Just remove this type and use plain 'unsigned int' consistently,
as it is already use almost everywhere in this file.
Fixes: b04641a3f4 ("drm/amd/display: Add Renoir DML")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
core:
- Some cleanups and fixes in the self-refresh helpers
- Some cleanups and fixes in the atomic helpers
amdgpu:
- Fix a 64 bit divide
- Prevent a memory leak in a failure case in dc
- Load proper gfx firmware on navi14 variants
- Add more navi12 and navi14 PCI ids
- Misc fixes for renoir
- Fix bandwidth issues with multiple displays on vega20
- Support for Dali
- Fix a possible oops with KFD on hawaii
- Fix for backlight level after resume on some APUs
- Other misc fixes
panfrost:
- Multiple panfrost fixes for regulator support and page fault handling
-----BEGIN PGP SIGNATURE-----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=yCyF
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-09-27' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Fixes built up over the past 1.5 weeks or so, it's two weeks of
amdgpu, some core cleanups and some panfrost fixes. I also finally
figured out why my desktop was slow to do a bunch of stuff (someone
gave it an IPv6 address which can't reach anything!).
core:
- Some cleanups and fixes in the self-refresh helpers
- Some cleanups and fixes in the atomic helpers
amdgpu:
- Fix a 64 bit divide
- Prevent a memory leak in a failure case in dc
- Load proper gfx firmware on navi14 variants
- Add more navi12 and navi14 PCI ids
- Misc fixes for renoir
- Fix bandwidth issues with multiple displays on vega20
- Support for Dali
- Fix a possible oops with KFD on hawaii
- Fix for backlight level after resume on some APUs
- Other misc fixes
panfrost:
- Multiple panfrost fixes for regulator support and page fault
handling"
* tag 'drm-next-2019-09-27' of git://anongit.freedesktop.org/drm/drm: (34 commits)
drm/amd/display: prevent memory leak
drm/amdgpu/gfx10: add support for wks firmware loading
drm/amdgpu/display: include slab.h in dcn21_resource.c
drm/amdgpu/display: fix 64 bit divide
drm/panfrost: Prevent race when handling page fault
drm/panfrost: Remove NULL checks for regulator
drm/panfrost: Fix regulator_get_optional() misuse
drm: Measure Self Refresh Entry/Exit times to avoid thrashing
drm: Fix kerneldoc and remove unused struct member in self_refresh helper
drm/atomic: Rename crtc_state->pageflip_flags to async_flip
drm/atomic: Reject FLIP_ASYNC unconditionally
drm/atomic: Take the atomic toys away from X
drm/amdgpu: flag navi12 and 14 as experimental for 5.4
drm/kms: Duct-tape for mode object lifetime checks
drm/amdgpu: add navi12 pci id
drm/amdgpu: add navi14 PCI ID for work station SKU
drm/amdkfd: Swap trap temporary registers in gfx10 trap handler
drm/amd/powerplay: implement sysfs for getting dpm clock
drm/amd/display: Restore backlight brightness after system resume
drm/amd/display: Implement voltage limitation for dali
...
drm-fixes-5.4-2019-09-25:
amdgpu:
- Fix a 64 bit divide
- Prevent a memory leak in a failure case in dc
- Load proper gfx firmware on navi14 variants
drm-fixes-5.4-2019-09-19:
amdgpu:
- Add more navi12 and navi14 PCI ids
- Misc fixes for renoir
- Fix bandwidth issues with multiple displays on vega20
- Support for Dali
- Fix a possible oops with KFD on hawaii
- Fix for backlight level after resume on some APUs
- Other misc fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925213500.3490-1-alexander.deucher@amd.com
- Some cleanups and fixes in the self-refresh helpers
- Some cleanups and fixes in the atomic helpers
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXYjuIAAKCRDj7w1vZxhR
xfNKAP9dlMLleLnjvAnCpI/Q2YZAktGCC9mIvqSzXJz52mwXNQEA5avYLerwa2+J
P5xmO7mr2/9gzeeeWE1xaufQwZnYrwY=
=Z99W
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2019-09-23' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
- Multiple panfrost fixes for regulator support and page fault handling
- Some cleanups and fixes in the self-refresh helpers
- Some cleanups and fixes in the atomic helpers
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923160946.nvaqiw5j7fpcdhc7@gilmour
In dcn*_create_resource_pool the allocated memory should be released if
construct pool fails.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's apparently needed in some configurations.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- add modpost warn exported symbols marked as 'static' because 'static'
and EXPORT_SYMBOL is an odd combination
- break the build early if gold linker is used
- optimize the Bison rule to produce .c and .h files by a single
pattern rule
- handle PREEMPT_RT in the module vermagic and UTS_VERSION
- warn CONFIG options leaked to the user-space except existing ones
- make single targets work properly
- rebuild modules when module linker scripts are updated
- split the module final link stage into scripts/Makefile.modfinal
- fix the missed error code in merge_config.sh
- improve the error message displayed on the attempt of the O= build
in unclean source tree
- remove 'clean-dirs' syntax
- disable -Wimplicit-fallthrough warning for Clang
- add CONFIG_CC_OPTIMIZE_FOR_SIZE_O3 for ARC
- remove ARCH_{CPP,A,C}FLAGS variables
- add $(BASH) to run bash scripts
- change *CFLAGS_<basetarget>.o to take the relative path to $(obj)
instead of the basename
- stop suppressing Clang's -Wunused-function warnings when W=1
- fix linux/export.h to avoid genksyms calculating CRC of trimmed
exported symbols
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=VGqV
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- add modpost warn exported symbols marked as 'static' because 'static'
and EXPORT_SYMBOL is an odd combination
- break the build early if gold linker is used
- optimize the Bison rule to produce .c and .h files by a single
pattern rule
- handle PREEMPT_RT in the module vermagic and UTS_VERSION
- warn CONFIG options leaked to the user-space except existing ones
- make single targets work properly
- rebuild modules when module linker scripts are updated
- split the module final link stage into scripts/Makefile.modfinal
- fix the missed error code in merge_config.sh
- improve the error message displayed on the attempt of the O= build in
unclean source tree
- remove 'clean-dirs' syntax
- disable -Wimplicit-fallthrough warning for Clang
- add CONFIG_CC_OPTIMIZE_FOR_SIZE_O3 for ARC
- remove ARCH_{CPP,A,C}FLAGS variables
- add $(BASH) to run bash scripts
- change *CFLAGS_<basetarget>.o to take the relative path to $(obj)
instead of the basename
- stop suppressing Clang's -Wunused-function warnings when W=1
- fix linux/export.h to avoid genksyms calculating CRC of trimmed
exported symbols
- misc cleanups
* tag 'kbuild-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (63 commits)
genksyms: convert to SPDX License Identifier for lex.l and parse.y
modpost: use __section in the output to *.mod.c
modpost: use MODULE_INFO() for __module_depends
export.h, genksyms: do not make genksyms calculate CRC of trimmed symbols
export.h: remove defined(__KERNEL__), which is no longer needed
kbuild: allow Clang to find unused static inline functions for W=1 build
kbuild: rename KBUILD_ENABLE_EXTRA_GCC_CHECKS to KBUILD_EXTRA_WARN
kbuild: refactor scripts/Makefile.extrawarn
merge_config.sh: ignore unwanted grep errors
kbuild: change *FLAGS_<basetarget>.o to take the path relative to $(obj)
modpost: add NOFAIL to strndup
modpost: add guid_t type definition
kbuild: add $(BASH) to run scripts with bash-extension
kbuild: remove ARCH_{CPP,A,C}FLAGS
kbuild,arc: add CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3 for ARC
kbuild: Do not enable -Wimplicit-fallthrough for clang for now
kbuild: clean up subdir-ymn calculation in Makefile.clean
kbuild: remove unneeded '+' marker from cmd_clean
kbuild: remove clean-dirs syntax
kbuild: check clean srctree even earlier
...
It's the only flag anyone actually cares about. Plus if we're unlucky,
the atomic ioctl might need a different flag for async flips. So
better to abstract this away from the uapi a bit.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190903190642.32588-3-daniel.vetter@ffwll.ch
Laptops with AMD APU doesn't restore display backlight brightness after
system resume.
This issue started when DC was introduced.
Let's use BL_CORE_SUSPENDRESUME so the backlight core calls
update_status callback after system resume to restore the backlight
level.
Tested on Dell Inspiron 3180 (Stoney Ridge) and Dell Latitude 5495
(Raven Ridge).
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
we only want the lowest voltage to be available for dali.
[How]
Use the get_highest_allowed_voltage_level function
to return 0 for dali
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dali is a new asic revision based on raven2
Add the ID and ASICREV_IS_DALI define
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When more than 2 displays are connected to the graphics card,
only the minimum memory clock is needed. However, when more
displays are connected, the minimum memory clock is not
sufficient enough to support the overwhelming bandwidth.
System will hang under this circumstance.
Also, the old code didn't address HBM cards, which has 2
pseudo channels. We need to add the HBM part here.
[How]
When graphics card connects to 2 or more displays,
switch to high memory clock. Also, choose memory
multiplier based on whether its regular DRAM or HBM.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1. OUTSTANDING_REQUEST_LIMIT update from 0xFF to 0x1F (HW doc update)
2. using memory type to convert UMC's MCLK to Yclk.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With stutter mode enabled, NMI prints frequently.
Disable stutter for the moment because NMI warning storm, and will
enable it back till the issue is addressed
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The earlier patch "Hook up calls to do stereo mux and dig programming..."
doesn't include update for dcn21.
[How]
Align dcn21 gpio settings with updated stereo control interface.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Separating the hardware initialization from the creation of the
dc structures gives greater flexibility to the dm to override
options for debugging.
[How]
Move the hardware initialization call to a new function,
dc_hardware_init. No functional change is intended.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I2C write command always send mot = true will cause sink state incorrect.
[How]
1. Remove default i2c write mot = true.
2. Deciding mot flag by is_end_of_payload flag.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new implementation changed the behavior to allow process setMode
to DAL when DAL returns empty mode query for unplugged display.
This will trigger additional disable_link().
When unplug HDMI from MST dock, driver will update stream->signal to
"Virtual". disable_link() will call disable_output() if the signal type
is not DP and induce other displays on MST dock show black screen.
[How]
Don't need to process disable_output() if the signal type is virtual.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn20_calculate_dlg_params was incorrectly indexing pipe src and
dst structs when extracting global sync params.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Global sync update was missing vtg update resulting in underflow if
vstartup decreased a significant amount.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Even if YUV420 is available for video mode, YUV444 is still
automatically selected. This poses a problem for compliance tests.
[How]
Add a per-connector debugfs entry "force_yuv420_output" to force
selection of YUV420 mode.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Surface dchub/dpp update would not trigger if a stream update was the
only cause. This change now allows stream flags to trigger this update.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
A function to adjust DPP clocks with DTO already exists; function code
is identical to the code replaced here
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The issue is specific for linux, as on timings such as 8K@60
or 4K@144 DSC should be working in combination with ODM Combine
in order to ensure that we can run those timings. The validation
for those timings was passing, but when pipe split was happening
second pipe wasn't being programmed.
[how]
Rebuild mapped resources if we split stream for ODM.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current configuration 0 is just a placeholder, and final parameters needed.
Also, configuration 1 is expected to emulate ABM 2.1 but is too aggressive.
[How]
Redefine configuration 0 with the finalized parameters, and increase the
contrast gain of configuration 1 so that it properly emulates ABM 2.1.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Secondary viewport dimension/position registers are not programmed,
which can cause issues in some stereo configurations.
[How]
Add register definitions and register programming.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently we restrict the number of encoders that can be linked to
a connector to 3, increase it to match the maximum number of encoders
that can be initialized(32).
To more effiently do that lets switch from an array of encoder ids to
bitmask.
v2: Fixing missed return on amdgpu_dm_connector_to_encoder()
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: dri-devel@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190913232857.389834-2-jose.souza@intel.com
It is fine for displays without audio functionality to not provide
any SAD block in their EDID. Do not log an error in that case,
just return quietly.
This fixes half of bug fdo#107825:
https://bugs.freedesktop.org/show_bug.cgi?id=107825
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in the variable name eanble,
rename it to enable.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
we only want the lowest voltage to be available for dali.
[How]
Use the get_highest_allowed_voltage_level function
to return 0 for dali
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dali is a new asic revision based on raven2
Add the ID and ASICREV_IS_DALI define
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DP1.2 LL CTS test failure.
[How]
The failure is caused by not verify stream link is equal
to link, only check stream and link is not null.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1. OUTSTANDING_REQUEST_LIMIT update from 0xFF to 0x1F (HW doc update)
2. using memory type to convert UMC's MCLK to Yclk.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Edid Utility wishes to include DSC module from driver instead
of doing it's own logic which will need to be updated every time
someone modifies the driver logic.
[How]
Modify some functions such that we dont need to pass the entire
DC structure as parameter.
-Remove DC inclusion from module.
-Filter out problematic types and inclusions
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Underflow occurs on some display setups(repro'd on 3x4K HDR) on boot,
mode set, and hot-plugs with. Underflow occurs because mem clk
is not set high after disabling pstate switching. This behaviour occurs
because some calculations assumed displays were synchronized.
[How] Add a condition to check if timing sync is disabled so that
synchronized vblank can be set to false.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc_destroy should only clean up SW, this is because GPUs may be
removed before driver unload, leading to HW to be unavailable.
[how]
remove GPIO close as part of GPIO destroy, this is unnecessary because
GPIO is not shared, and GPIOs are generally closed after being opened
Add tracking to HW access during destructor to make future issues
easier to pinpoint, and block access to prevent hangs.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New behaviour will track global updates and update any hw that isn't
related to current stream being updated.
This should fix any issues caused by pipe split pipes being taken
by other streams.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Need to add missing surface address register definitions.
- RGBE+A does not work in a stereo configuration because
surface addresses are no programmed correctly.
[How]
Added the register definitions and surface address programming.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's sometimes useful to have this option when debugging
[how]
Add a config flag. If the flag is not set, use driver default policy.
If the flag is set, use the value from the flag as the starting DSC slice
height.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The requirement has been clarified and only DSC 4:2:2 Native has to
be disabled.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We should not allocate payloads if the link is lost until the link is retrained.
Some displays require this.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Driver defaults to 1-tap subsample mode for 4:2:2.
DCE11.2 added 3-tap. The policy is:
DCE8-DCE11 - change to 2-tap, it's better than 1-tap.
DCE11.2+ - use 3-tap
Note that 4:2:0 was added in DCE11.2 and already uses 3-tap always.
Note 2 is that DCE not covered on Linux, only DCN+
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When user mode use i2c over aux through ADL or DDI, the function
dal_ddc_service_query_ddc_data will be called. There are two issues.
1. When read/write length > 16byte, current always return false because
the DEFAULT_AUX_MAX_DATA_SIZE != length.
2. When usermode only need to read data through i2c, driver will write
mot = true at the same address and cause i2c sink confused. Therefore
the following read command will get garbage.
[How]
1. Add function dal_dcc_submit_aux_command to handle length > 16 byte.
2. Check read size and write size when query ddc data.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML diags tests are failing because the struct contents get
clobbered by a memcpy.
[How]
Remove the memcpy call.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The earlier patch "Hook up calls to do stereo mux and dig programming..."
doesn't include update for dcn21.
[How]
Align dcn21 gpio settings with updated stereo control interface.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With stutter mode enabled, NMI prints frequently.
Disable stutter for the moment because NMI warning storm, and will
enable it back till the issue is addressed
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-next-5.4-2019-08-30:
amdgpu:
- Add DC support for Renoir
- Add some GPUVM hw bug workarounds
- add support for the smu11 i2c controller
- GPU reset vram lost bug fixes
- Navi1x powergating fixes
- Navi12 power fixes
- Renoir power fixes
- Misc bug fixes and cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830212650.5055-1-alexander.deucher@amd.com
Kbuild provides per-file compiler flag addition/removal:
CFLAGS_<basetarget>.o
CFLAGS_REMOVE_<basetarget>.o
AFLAGS_<basetarget>.o
AFLAGS_REMOVE_<basetarget>.o
CPPFLAGS_<basetarget>.lds
HOSTCFLAGS_<basetarget>.o
HOSTCXXFLAGS_<basetarget>.o
The <basetarget> is the filename of the target with its directory and
suffix stripped.
This syntax comes into a trouble when two files with the same basename
appear in one Makefile, for example:
obj-y += foo.o
obj-y += dir/foo.o
CFLAGS_foo.o := <some-flags>
Here, the <some-flags> applies to both foo.o and dir/foo.o
The real world problem is:
scripts/kconfig/util.c
scripts/kconfig/lxdialog/util.c
Both files are compiled into scripts/kconfig/mconf, but only the
latter should be given with the ncurses flags.
It is more sensible to use the relative path to the Makefile, like this:
obj-y += foo.o
CFLAGS_foo.o := <some-flags>
obj-y += dir/foo.o
CFLAGS_dir/foo.o := <other-flags>
At first, I attempted to replace $(basetarget) with $*. The $* variable
is replaced with the stem ('%') part in a pattern rule. This works with
most of cases, but does not for explicit rules.
For example, arch/ia64/lib/Makefile reuses rule_as_o_S in its own
explicit rules, so $* will be empty, resulting in ignoring the per-file
AFLAGS.
I introduced a new variable, target-stem, which can be used also from
explicit rules.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Hook up the DML changes for renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check for renoir first.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a kconfig option to enable renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable the building of dcn21 support.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing parameters, to make dcn21 compile
without errors
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the rev id for renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
call update_bw_bounding_box in DC construct
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hook up renoir support to KMS.
v2: squash in "Fixes for Renoir in amdgpu_dm"
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add Renoir DCN version in DC and handle it
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
rename VM_CONTEXT0 to MMVM_CONTEXT0 as that is the name defined in
the register files
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DML provides the display configuration validation as provided
by the hw teams.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Controls display clocks and interfaces with powerplay for
clock and power requirements.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Controls the display hw's interface to memory.
v2: rebase (Alex)
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are the registers used to program the hubbub hw.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This provides the interface to memory for the display hw.
v2: minor cleanup (Alex)
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Provides the interface to configure display interrrupts on renoir.
v2: rebase fix (Alex)
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This defines the interface for communicating requirements
between DC and powerplay.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are the registers used to for the hw sequences
for modesetting.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are the registers used to program the clock hw.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After commit a9f54ce3c6 ("drm/amd/display: Refactoring VTEM"),
there is no caller in tree.
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If CONFIG_DRM_AMD_DC_DSC_SUPPORT is not set, build fails:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_hwseq.c: In function dcn20_hw_sequencer_construct:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_hwseq.c:2099:28:
error: dcn20_dsc_pg_control undeclared (first use in this function); did you mean dcn20_dpp_pg_control?
dc->hwss.dsc_pg_control = dcn20_dsc_pg_control;
^~~~~~~~~~~~~~~~~~~~
dcn20_dpp_pg_control
Use CONFIG_DRM_AMD_DC_DSC_SUPPORT to guard this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8a31820b12 ("drm/amd/display: Make init_hw and init_pipes generic for seamless boot")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since reservation_object_wait_timeout_rcu is called with
interruptable set to false it's wrong to say
'or interrupted' in the error message.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pass the connector info to the CEC adapter. This makes it possible
to associate the CEC adapter with the corresponding drm connector.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20190814104520.6001-2-darekm@google.com
drm-next-5.4-2019-08-23:
amdgpu:
- Enable power features on Navi12
- Enable power features on Arcturus
- RAS updates
- Initial Renoir APU support
- Enable power featyres on Renoir
- DC gamma fixes
- DCN2 fixes
- GPU reset support for Picasso
- Misc cleanups and fixes
scheduler:
- Possible race fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823202620.3870-1-alexander.deucher@amd.com
[WHY] value of dchub_ref_clock is decided by dchubbub global timer
settings which is programmed by vbios command table disp_init.
for multi-GPU case, vbios is posted only for primary GPU. without
vbios posted for the secondary GPU, value of dchub_ref_clock is not
set properly. this value will affect dcn bandwidth calcuation and
cause underflow. user will see screen flicking during driver
installation for dual GPU case.
[HOW] dc init_hw always call vbios command table disp_init to
make sure dchubbub global timer is configured and enable.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The register LVTMA_PWRSEQ_CNTL is used to determine the power state of the
embedded display. Currently we do not actually read this register's values,
so during power down we think that this display is already off, so we skip
calling into VBIOS to actually turn it off.
[How]
- add relevant fields to shift / mask initialization
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous workaround to prevent a vsync flip to be converted
to immediate flip is no longer needed, and is risky because
there are cases where it can result in infinite loop.
[how]
Remove wait loop (which is potentially infinite) before locking
pipe
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should be using the ddc_num from res_caps. As the
pipe count != number of i2c resources.
[How]
Use ddc_num from res_cap instead of pipe count.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Existing HW Features, HW Diags test requested that the
registers be exposed.
[How]
Add V_TOTAL_MID to existing DC structures.
Make sure values are passed down throughout DC
Add Register definition.
Program the additional registers
Add additional Logic for V_TOTAL_CONTROL.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Calculating DCFCLK DS time requires calculating
delivery time for luma/chroma, but this value is
not calculated in DMLv2, it was inadvertently
removed when porting DMLv2
[how]
Add the calculation back
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DRM provides drm_dp_mst_dump_topology, which prints
useful information about MST devices
Hook this up to a debugfs file named amdgpu_mst_topology
Signed-off-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
OS will reserve HW state in UEFI mode.
Driver init_hw reset to RGB which caused HDMI green in YCbCr mode.
read HW blank_color based on acc_mode.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A recent bug showed that logging would be useful in debugging
various gamma issues.
[How]
Add logging in dc.
Fix formatting for easier graphing.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] HW rotation is not enabled. Calculations for cursor rotation
are wrong for the values passed to set_cursor_position.
[How] Swap Src rect and height and vertically mirror surface for
the correct surface rotation direction. Cursor position is rotated
according to angle. Offset calculations are tweaked for non-rotated
cursor hotspot and width/height.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to have the ability to to tell us set degamma on the cursor.
[How]
Pass a flag down to register programming that tells us if the
current surface format needs cursor degamma.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update bw validation to use prev and next odm pipe pointers
for populating dml inputs.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to memset all odm pipes when calling dc_remove_stream_from_ctx
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn20 requires special casing for odm.
This change treats odm as alternative to mpc tree on dcn20.
This is planned to be fixed in a future refactor
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
num_slices_h was not being checked
[How]
Fix the typo and check num_slices_h
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ODM next and prev pipe were missing from dc_copy_state
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In newer hardware MANUAL_FLOW_CONTROL is not a trigger bit. Due to this
front porch is fixed and in these hardware freesync does not work.
[How]
Change the programming to generate a pulse so that the event will be
triggered, front porch will be cut short and freesync will work.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With visual confirm enabled, displays where ODM combine is enabled
has a test pattern stuck on the right half of the display even
though the display is unblanked.
[how]
Add a condition to not show the colour ramp test pattern when the
display is unblanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Video Timing Extended Metadata packet (VTEM) is not
specific to freesync. So move it out of freesync module
[How]
- Moved VTEM from freesync module to info_packet module
- Created new structure for VTEM parameters that can be used for VRR
and FVA
Signed-off-by: Ahmad Othman <ahmad.othman@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Ahmad Othman <Ahmad.Othman@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This function is not being used, it was left in
when introducing DCN2
[How]
Remove the function
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
during a refactor a redundant code that has unknown behaviour was added.
[how]
removed old bad code
Fixes: 8a31820b12 ("drm/amd/display: Make init_hw and init_pipes generic for seamless boot")
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How] Allocate memory for default page and program memory block addr
into default page addr register.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
IEEE OUI will now be used while referring to certain vendors.
instead of normal index
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before a statically allocated PPS data structure, that did
get zeroed-out at startup, had been re-used for making packed PPS
SDP. With S3 fix, using a non-initialized PPS data structure was
introduced, while wrongly assuming it'd get initialized before it's
populated. As a consequence 'vbr_enable' and perhaps some other
fields are left uninitialized when making packed PPS SDP. This can
affect 'simple_422' as well because of the way PPS SDP packing is
done (the fields are not masked first, only shifted). The behavior
will be different, depending on the content of uninitialized data.
[how]
Zero-out PPS data structure at initialization time before it's
populated
Fixes: 1a9e3d4569 ("drm/amd/display: Set DSC before DIG front-end is connected to its back-end")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add new function to get the voltage at the end of
dcn_validate_bandwidth, to check against the
highest voltage we allow.
Created a stub to allow for optimizations
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Sun peng Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding NULL checks to various parameters in log_tf, to avoid
nullptr errors
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Nikola Cornij <Nikola.Cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the writeback Hratio and Vratio in dml.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A previous odm change broke stream enable by always setting
n_multiply as if odm was on.
This fixes the check for odm by making sure opp count is >1
rather than not 0.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ABM 2.3 firmware expects information in iRAM that differs from previous
versions of ABM, so a mechanism is required to provide it with that
information.
[How]
Extend the existing iRAM definition to include parameters added by
ABM 2.3, and load it if DMCU is running ABM 2.3.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With Scatter Gather enabled, HUBP underflows during MPO enabled video
playback. hubp_init has a register write that fixes this problem, but
the register is cleared when HUBP gets power gated.
[how]
Make a call to hubp_init during enable_plane, so that the fix can
be applied after HUBP powers back on again.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Disable_audio_stream gets enum option as a paramenter which will decide
if we free acquired resources or not. However checks for the option is
guarded by the other condition which check if audio stream is getting
diabled more than once. With both conditions combined, if we attempt to
disable audio stream twice in a row, first with keep and second with
free as an option, we will never free any resources, which will make
system think there is audio endpoint connected even after we plug out
the device
[How]
Get rid of option as parameter to disable_audio_stream and move the part
of the code that free acquired resources to outside where to keep or to
free resources is actually determined
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dig_encoder_sel_to_atom will always return zero on any ASIC version
past DCE80 since programming of the FE selection is handled by
driver, but the translation code was left in the function, making
it look like a coding error.
[How]
Remove code that has no effect, and replace with a comment describing
why it returns zero.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm is handled using top_bottom pipe by special casing
the differing opps to differentiate from mpc combine.
Since top/bottom pipe list was made to track mpc muxing this creates
difficulties in adding a 4 pipe odm case support.
Rather than continue using mpc combine list, this change reworks odm
to use it's own linked list to keep track of odm combine pipes. This
also opens up options for using mpo with odm, if a practical use case
is ever found.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a dcfeaturemask flag for mclk switching. Disable by default;
enable once the feature has seen more testing.
Set amdgpu.dcfeaturemask=2 on the kernel command line in grub
to enable this.
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Properly set all_displays_in_sync so that when the data is
propagated to powerplay, it's set properly and we can enable
mclk switching when all monitors are in sync.
v2: fix logic, clean up
v3: check for blending chains, simplify logic
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was broken by a previous change switching to cached fw_info.
Fixed by inverting a valid bool check.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=111432
Fixes: 9adc8050bf ("drm/amd/display: make firmware info only load once during dc_bios create")
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the pointer init_data is dereferenced on the assignment
of fw_info before init_data is sanity checked to see if it is null.
Fix te potential null pointer dereference on init_data by only
performing dereference after it is null checked.
Addresses-Coverity: ("Dereference before null check")
Fixes: 9adc8050bf ("drm/amd/display: make firmware info only load once during dc_bios create")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In create_stream_for_sink, check for SST DP connectors
Parse DSC caps to DC format, then, if DSC is supported,
compute the config
DSC hardware will be programmed by dc_commit_state
Tested-by: Mikita Lipski <Mikita.Lipski@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 80e80ec817.
This commit fixed an issue with underscan commits not updating all
needed timing values, but through various refactors it is no longer
necessary. It causes corruption on odm combine by
overwriting the halved h_active in the stream timing
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 6c5be4ac63.
This commit was accidentally promoted twice
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit ec8763486d.
Re-enable enc2_dp_set_dsc_config. This function caused warnings
due to missing register definitions. With the registers added,
this now works
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 9e14d4f17e.
optc dsc config was causing warnings due to missing register
definitions. With the registers restored, the function can
be re-enabled
The reverted commit also disabled sanity checks and dsc
power gating. The sanity check warnings are not associated
with dsc, and power gating on dsc still has an issue on
non-dsc monitors where the dsc hardware block is never init
and so cannot respond to power gating requests. Therefore,
those are left as is
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When building arm32 allyesconfig:
ld.lld: error: undefined symbol: __aeabi_uldivmod
>>> referenced by dc_link.c
>>> gpu/drm/amd/display/dc/core/dc_link.o:(wait_for_alt_mode) in archive drivers/built-in.a
>>> referenced by dc_link.c
>>> gpu/drm/amd/display/dc/core/dc_link.o:(wait_for_alt_mode) in archive drivers/built-in.a
time_taken_in_ns is of type unsigned long long so we need to use div_u64
to avoid this error.
Fixes: b5b1f45549 ("drm/amd/display: Enable type C hotplug")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to ensure that we're holding the lock on the CRTC when setting
the CRC source since we're modifying the CRTC state directly.
We also need to wait for any outstanding non-blocking commits to finish
so they aren't reading state that's potentially being modified -
non-blocking commits don't hold the CRTC lock while doing commit tail
work.
[How]
Lock the CRTC using its mutex. While holding the lock check if there's
any commit active on the CRTC - if there is, it's non-blocking and
we should wait until it's finished by waiting for hw_done to be
signaled since that's the last point where we touch CRTC state.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Calling amdgpu_dm_crtc_set_crc_source in amdgpu_dm directly has the
consequence of adding additional vblank references or starting DPRX
CRC capture more than once without calling stop first.
Vblank references for CRC capture should be managed entirely by opening
and closing the CRC file from userspace.
Stream state also shouldn't be required on the CRC so we can close the
file after the CRTC has been disabled.
[How]
Do DC programming required for configuring CRC capture separately from
setting the source. Whenever we re-enable or reset a CRC this
programming should be reapplied.
CRC vblank reference handling in amdgpu_dm can be entirely dropped after
this.
Stream state also no longer needs to be required since we can just defer
the programming to when the stream is actually enabled.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change is a refactor in preparation for adding locking and removing
the requirement for a stream state on the CRTC for enabling CRC capture
to fix igt@kms_plane_multiple@* warnings.
[How]
We can get the aux by finding the matching connector for the CRTC
with the assumption that we're not doing cloning.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The call to drm_crtc_vblank_get can fail if vblank is disabled and
we try to increment the reference.
Since drm_crtc_vblank_get internally drops the reference when it fails
it means the subsequent drm_crtc_vblank_put(...) when closing the file
drops a zero reference.
This was found via igt@kms_plane@pixel-format-pipe-A-planes.
[How]
Check the return code and return it on failure.
We wouldn't have been able to enable CRC reading anyway since vblank
wasn't enabled.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The only place where state->max_bpc is updated on the connector is
at the start of atomic check during drm_atomic_connector_check. It
isn't updated when adding the connectors to the atomic state after
the fact. It also doesn't necessarily reflect the right value when
called in amdgpu during mode validation outside of atomic check.
This can cause the wrong bpc to be used even if the max_requested_bpc
is the correct value.
[How]
Don't rely on state->max_bpc reflecting the real bpc value and just
do the min(...) based on display info bpc and max_requested_bpc.
Fixes: 01933ba42d ("drm/amd/display: Use current connector state if NULL when checking bpc")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dma-buf: add reservation_object_fences helper, relax
reservation_object_add_shared_fence, remove
reservation_object seq number (and then
restored)
- dma-fence: Shrinkage of the dma_fence structure,
Merge dma_fence_signal and dma_fence_signal_locked,
Store the timestamp in struct dma_fence in a union with
cb_list
Driver Changes:
- More dt-bindings YAML conversions
- More removal of drmP.h includes
- dw-hdmi: Support get_eld and various i2s improvements
- gm12u320: Few fixes
- meson: Global cleanup
- panfrost: Few refactors, Support for GPU heap allocations
- sun4i: Support for DDC enable GPIO
- New panels: TI nspire, NEC NL8048HL11, LG Philips LB035Q02,
Sharp LS037V7DW01, Sony ACX565AKM, Toppoly TD028TTEC1
Toppoly TD043MTEA1
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXVqvpwAKCRDj7w1vZxhR
xa3RAQDzAnt5zeesAxX4XhRJzHoCEwj2PJj9Re6xMJ9PlcfcvwD+OS+bcB6jfiXV
Ug9IBd/DqjlmD9G9MxFxfSV946rksAw=
=8uv4
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-08-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.4:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dma-buf: add reservation_object_fences helper, relax
reservation_object_add_shared_fence, remove
reservation_object seq number (and then
restored)
- dma-fence: Shrinkage of the dma_fence structure,
Merge dma_fence_signal and dma_fence_signal_locked,
Store the timestamp in struct dma_fence in a union with
cb_list
Driver Changes:
- More dt-bindings YAML conversions
- More removal of drmP.h includes
- dw-hdmi: Support get_eld and various i2s improvements
- gm12u320: Few fixes
- meson: Global cleanup
- panfrost: Few refactors, Support for GPU heap allocations
- sun4i: Support for DDC enable GPIO
- New panels: TI nspire, NEC NL8048HL11, LG Philips LB035Q02,
Sharp LS037V7DW01, Sony ACX565AKM, Toppoly TD028TTEC1
Toppoly TD043MTEA1
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: fixup dma_resv rename fallout]
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190819141923.7l2adietcr2pioct@flea
[Why]
Previous SOC bounding box firmware loading logic was for NV10, when we
still had it in firmware. Now that it's brought into driver code, and
NV12 BB is in firmware, this logic needs to be repurposed for NV12.
[How]
Set SOC_BOUNDING_BOX_VALID to false, and add the dcn_2_0_nv12_soc BB
struct. In init_soc_bounding_box, load firmware to nv12 BB instead.
In addition, conditionally update and patch the BB, depending on ASIC
REV.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN10 performs color processing before MPC combination, causes color
shift in RGB colorspaces when positive brightness offset is applied
However, YCbCr is still unfixed and remains disabled
[How]
Add layerIndex to dc_plane_state and dc_plane_info structs
Re-enable MPO when brightness is adjusted and colorspace is not YCbCr
Set rear plane's brightness offset to 0 when front plane visible
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
disable_az_endpoint has been skipped because
dc->debug.az_endpoint_mute_only = true.
[how]
set dc->debug.az_endpoint_mute_only false when PPLIB’s PME notification function
pointer is not NULL at the dcn10_resource construct function,because right now
SMU/PPLIB and DAL all have the AZ D3 force PME notification implemented. AZ D3 should work.
Signed-off-by: yanyan kang <Yanyan.Kang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
During detection link training if a display is disconnected,
the current code will retry 3 times of link training
on disconnected link before giving up.
[how]
Before each retry check for HPD status, only retry
verify link cap when HPD is still high.
Also put a 10ms delay between each retry to improve
the chance of success.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable dcn_mem_pwr as golden setting updates
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the paremeters are extracted as if dml is calculating
using pipes as we pass them in. in reality, dml internally merges
pipes into planes if pipe split is detected.
This change adds reverse logic to dcn20_calculate_dlg_params so
that the global sync parameters can be correctly extracted for
all the pipes when pipe split is enabled.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some logs messages were not precise and some new log messages
were needed after "get packed PPS" function was introduced
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A recent bug showed that logging would be useful in debugging
various gamma issues.
[How]
Add logging in dc.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are repeated (but guarded) definitions of dwb_src enums. There are
also unused entires. Clean them up.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These are needed to send back DRM vblank events in the case where VRR
is on. Without the interrupt enabled we're deferring the events into the
vblank queue and userspace is left waiting forever to get back the
events they need.
Found using igt@kms_vrr - the test fails immediately due to vblank
timeout.
[How]
Register them the same way we're handling it for DCN1.
This fixes igt@kms_vrr for DCN2.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
OGAM_MEM_PWR could stay in light up when driver woke up to update gamma.
either disable MEM_LOW power feature or set to OGAM_bypass could make artificial color distortion goes away.
Easy reproduce after LOW_MEM Power feature enables and resume from S3.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Julian Parkin <jparkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A misleading message "Programming PPS" appears before both programming
and "query PPS" functions
[how]
Move the message from "log PPS" function to "program PPS" function
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not all ASIC types have this function implemented - check before
calling.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Julian Parkin <jparkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The type was changed previously to better reflect possible register
values.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A recent bug showed that logging would be useful in
debugging various gamma issues.
[How]
Add new log types and logging code to the color module.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If DSC is available, a higher picture quality is achieved by using
DSC with 4:4:4 format. Using 4:2:2 instead does not offer any benefit
and would only introduce loss of quality. Removing it reduces
maintenance and testing effort.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The vm config will be clear to 0 when system enter S4. It will
cause hubbub didn't know how to fetch data when system resume.
The flip always pending because earliest_inuse_address and
request_address are different.
[How]
Reprogram VM config when system resume
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and How]
We want to change where timing is done for alt mode.
Some of the commented out #ifs are needed for DCN20
so we enable them for that case.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Need to change interface function signature / add an enum
to reflect the available register field values
[How]
- Add a new enum and modify existing functions to use it instead
of bool
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current optc odm interface only accepts 2 opps, we need to
expand this to allow 4 to 1 odm combine.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to add DML struct members that were omitted in previous
DML implemenations.
[How]
- Add missing enum values
- Add missing struct members
- Set new input values in the fetch functions
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are currently two interfaces for exactly the same thing:
hupb_update_dchub in hupb and update_dchub in hubbub. The hubbub
version is currently unused past dcn10, largely because the call
from the dcn10 hardware sequencer does not call through the
interface, so the hupb interface was used instead. This is
confusing because of the duplicate code, the unused functions,
and the fact that more that one block currently owns this set
of registers.
[How]
Remove the hubp interface entirely, as well as the register
declarations that are not longer needed because of this. Change
the call site to always call the hubbub version through the
interface. Fix the update_dchub function in dcn20_hubbub.c to
program the correct registers for dcn20.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Resource mapping done in dcn20_validate_bandwidth has a flaw: When a full
update is performed, the HWSS will only update the MPCC tree for the stream
that is updated as opposed to all streams. This means that when mapping pipes
in validation, care must be taken to not change any existing mapping, otherwise it
leads to partial hw programming
[how]
it's not strictly necessary to track which stream/mpcc tree is being updated, but
rather it's sufficient to compare current and new state and just keep pipes that were
previously already mapped unchanged.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
At the time DIG FE is connected to its BE, the clocks in OTG are enabled and
PHY will also be set up. When DSC has to be used to fit the stream into the
available bandwidth, without DSC being set DIG could get exposed to the
higer bandwidth it (or link) could handle. This causes the HW to "reject"
video enable setup (the register shows that video enable was attempted, but
the status bit shows it as disabled).
[how]
- Separate DSC setup into DSC register config and DSC PPS SDP setup
- Move most of the DSC setup (register config) to before
dcn10_link_encoder_connect_dig_be_to_fe() is called
- Set up DSC PPS SDP after DIG FE is connected to its BE. This is because
setting DSC PPS SDP before that has no effect.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why] Minimum slice height is recommended by VESA DSC Spreadsheet user guide
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Support hlg OETF and EOTF based on BT.2100-2
Follow up is required.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous "less risky" implemenation of 3 tiered fallback is no longer necessary since
DMLv2 has gone through proper validation. v2 can now be used as the default and 1
level of fallback can be removed
[how]
remove previous workaround implemenation
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot (building SW state inheriting BIOS-initialized timing) was
enabled on DCN2, including fixes
[How]
Includes fixes for MPC, DPPCLK, and DIG FE mapping/OTG source select/
Pixel clock.
This is part 2 of 2 for seamless boot NV10
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
underflow seen on certain monitor setups caused by making dcnxx_init_hw
generic
[How]
by moving dcn20_init_hw into dcn10, we added a dcn-specific clk_mgr
init (dc->clk_mgr->funcs->init_clocks()). Thus, put old clk_mgr
memset in an else statement so both memsets don't get set
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For seamless boot the init_hw sequence must be split into
actual hardware vs pipes, in order to defer pipe initialization to set mode
and skip of pipe-destructive sequences
[How]
made dcn10_init_hw and dcn10_init_pipes generic for future dcns to inherit
deleted dcn20 specific versions. This is part 1 of a 2 partimplementation
of seamless boot
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When planes are enabled, they must be enabled using VSYNC update (not immediate).
However, before the VUPDATE occurs, DM may call with an "immediate" flip which is address
only. This operation would normally be okay, but if the locking for immediate flip happens
to occur before the VUPDATE associated with the initial plane enablement, it will cause HW
to hang.
[how]
HWSS should enforce plane enable in HW to be synchronous with the call that enables the plane.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
if dynamic allocation fails during gpio_open, it will cause crash due to
page fault.
[how]
handle allocation when gpio object gets created and prevent from calling
gpio_open if allocation failed
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Auto Overclock Memory fails for some systems that don't support
p-state.
[How] Implement the workaround, and it's corresponding enable flag.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DC does not correct account for the fact that DPP DTO is double buffered while DPP ref is not.
This means that when DPP ref clock is lowered when it's "safe to lower", the DPP blocks that need
an increased divider will temporarily have actual DPP clock drop below minimum while DTO
double buffering takes effect. This results in temporary underflow.
[how]
To fix this, DPP clock cannot be programmed atomically, but rather be broken up into the DTO and the
ref. Each has a separate "safe to lower" logic. When doing "prepare" the ref and dividers may only increase.
When doing "optimize", both may decrease. It is guaranteed that we won't exceed max DPP clock because
we do not use dividers larger than 1.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently every time DC wants to access firmware info we make a call
into VBIOS. This makes no sense as there is nothing that can change
runtime inside fw info and can cause issues when calling unstable
bios during bringup.
This change eliminate this behavior by only calling bios once for fw
info and keeping it stored as part of dc_bios.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We require a method to perform synchronous link training.
[HOW]
Sync LT is broken into 3 basic steps.
"Begin" starts the state machine, and resets "preferred" link settings.
"Attempt" will attempt to train the link with a given set of training
parameters.
"End" stops the state machine, and will optionally disable the link phy.
Between "Begin" and "End" DPCD:600h must not be set to "2"
(D3:Powered Down).
Between "Begin" and "End", there may be multiple "Attempts" with different
training parameters.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DCN20 common register list that contains registers shared
between DCN20 generations.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Support degamma ROM and RAM based on hardware capabilities.
Some refactoring into color module
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Gary Kattan <Gary.Kattan@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The math on deciding on how many
"frames to insert" sometimes sent us over the max refresh rate.
Also integer overflow can occur if we have high refresh rates.
[How]
Instead of clipping the frame duration such that it doesn’t go below the min,
just remove a frame from the number of frames to insert. +
Use unsigned long long for intermediate calculations to prevent
integer overflow.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When endpoint is at the boundary of a region, such as at 2^0=1
we find that the last segment has a sharp slope and some points
are clipped at the top.
[How]
If end point is 1, which is exactly at the 2^0 region boundary, we
need to program an additional region beyond this point.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
hdmi data scramble and tmds rate is not reset during pipe reset.
[how]
reset hdmi tmds rate and data scramble on pipe reset
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
drr is still enabled after driver is unloaded causing black screen
[how]
disable drr during pipe reset.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add to clk_mgr_internal struct, for future use.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For use by future ASICs
Signed-off-by: Sung Lee <sung.lee@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Be more consistent with the naming of the other DMA-buf objects.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/323401/
This should be 'dce_audio_mask', not 'dce_aduio_mask'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's large and doesn't need contiguous memory. Fixes
allocation failures in some cases.
v2: kvfree the memory.
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This file was accidentally added to the driver during
Navi promotion
Nothing includes it. No makefile attempts to compile it, and
it would fail compilation if they tried
Remove it
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>w
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-next-5.4-2019-08-09:
Same as drm-next-5.4-2019-08-06, but with the
readq/writeq stuff fixed and 5.3-rc3 backmerged.
amdgpu:
- Add navi14 support
- Add navi12 support
- Add Arcturus support
- Enable mclk DPM for Navi
- Misc DC display fixes
- Add perfmon support for DF
- Add scatter/gather display support for Raven
- Improve SMU handling for GPU reset
- RAS support for GFX
- Drop last of drmP.h
- Add support for wiping memory on buffer release
- Allow cursor async updates for fb swaps
- Misc fixes and cleanups
amdkfd:
- Add navi14 support
- Add navi12 support
- Add Arcturus support
- CWSR trap handlers updates for gfx9, 10
- Drop last of drmP.h
- Update MAINTAINERS
radeon:
- Misc fixes and cleanups
- Make kexec more reliable by tearing down the GPU
ttm:
- Add release_notify callback
uapi:
- Add wipe memory on release flag for buffer creation
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: resolved conflicts with ttm resv moving]
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190809184807.3381-1-alexander.deucher@amd.com
UAPI Changes:
- HDCP: Add a Content protection type property
Cross-subsystem Changes:
Core Changes:
- Continue to rework the include dependencies
- fb: Remove the unused drm_gem_fbdev_fb_create function
- drm-dp-helper: Make the link rate calculation more tolerant to
non-explicitly defined, yet supported, rates
- fb-helper: Map DRM client buffer only when required, and instanciate a
shadow buffer when the device has a dirty function or says so
- connector: Add a helper to link the DDC adapter used by that connector to
the userspace
- vblank: Switch from DRM_WAIT_ON to wait_event_interruptible_timeout
- dma-buf: Fix a stack corruption
- ttm: Embed a drm_gem_object struct to make ttm_buffer_object a
superclass of GEM, and convert drivers to use it.
- hdcp: Improvements to report the content protection type to the
userspace
Driver Changes:
- Remove drm_gem_prime_import/export from being defined in the drivers
- Drop DRM_AUTH usage from drivers
- Continue to drop drmP.h
- Convert drivers to the connector ddc helper
- ingenic: Add support for more panel-related cases
- komeda: Support for dual-link
- lima: Reduce logging
- mpag200: Fix the cursor support
- panfrost: Export GPU features register to userspace through an ioctl
- pl111: Remove the CLD pads wiring support from the DT
- rockchip: Rework to use DRM PSR helpers, fix a bug in the VOP_WIN_GET
macro
- sun4i: Improve support for color encoding and range
- tinydrm: Rework SPI support, improve MIPI-DBI support, move to drm/tiny
- vkms: Rework of the CRC tracking
- bridges:
- sii902x: Add support for audio graph card
- tc358767: Rework AUX data handling code
- ti-sn65dsi86: Add Debugfs and proper DSI mode flags support
- panels
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191,
Boe Himax8279d, Sharp LD-D5116Z01B
- Conversion of the device tree bindings to the YAML description
- jh057n00900: Rework the enable / disable path
- fbdev:
- ssd1307fb: Support more devices based on that controller
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXUwPUAAKCRDj7w1vZxhR
xQ4lAQDK2ijx29YHeZspbOwP4Nwq95DFs1uQcSm5GvbRt1JSowD9EwkLeNfkPkel
Xv1Ts/Frgq7ckH2e2zkLPyCOFCHd0wA=
=rIUl
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-08-08' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.4:
UAPI Changes:
- HDCP: Add a Content protection type property
Cross-subsystem Changes:
Core Changes:
- Continue to rework the include dependencies
- fb: Remove the unused drm_gem_fbdev_fb_create function
- drm-dp-helper: Make the link rate calculation more tolerant to
non-explicitly defined, yet supported, rates
- fb-helper: Map DRM client buffer only when required, and instanciate a
shadow buffer when the device has a dirty function or says so
- connector: Add a helper to link the DDC adapter used by that connector to
the userspace
- vblank: Switch from DRM_WAIT_ON to wait_event_interruptible_timeout
- dma-buf: Fix a stack corruption
- ttm: Embed a drm_gem_object struct to make ttm_buffer_object a
superclass of GEM, and convert drivers to use it.
- hdcp: Improvements to report the content protection type to the
userspace
Driver Changes:
- Remove drm_gem_prime_import/export from being defined in the drivers
- Drop DRM_AUTH usage from drivers
- Continue to drop drmP.h
- Convert drivers to the connector ddc helper
- ingenic: Add support for more panel-related cases
- komeda: Support for dual-link
- lima: Reduce logging
- mpag200: Fix the cursor support
- panfrost: Export GPU features register to userspace through an ioctl
- pl111: Remove the CLD pads wiring support from the DT
- rockchip: Rework to use DRM PSR helpers, fix a bug in the VOP_WIN_GET
macro
- sun4i: Improve support for color encoding and range
- tinydrm: Rework SPI support, improve MIPI-DBI support, move to drm/tiny
- vkms: Rework of the CRC tracking
- bridges:
- sii902x: Add support for audio graph card
- tc358767: Rework AUX data handling code
- ti-sn65dsi86: Add Debugfs and proper DSI mode flags support
- panels
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191,
Boe Himax8279d, Sharp LD-D5116Z01B
- Conversion of the device tree bindings to the YAML description
- jh057n00900: Rework the enable / disable path
- fbdev:
- ssd1307fb: Support more devices based on that controller
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808121423.xzpedzkpyecvsiy4@flea
[Why]
Underflow can occur in the case where we change buffer pitch, DCC state,
rotation or mirroring for a plane while also performing an immediate
flip. It can also generate a p-state warning stack trace on DCN1 which
is typically observed during the cursor handler pipe locking because of
how frequent cursor updates can occur.
[How]
Store the update type on each CRTC - every plane will have access to
the CRTC state if it's flipping. If the update type is not
UPDATE_TYPE_FAST then the immediate flip should be disallowed.
No changes to the target vblank sequencing need to be done, we just
need to ensure that the surface registers do a double buffered update.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pitch, DCC, rotation and mirroring can result in updates that are not
UPDATE_TYPE_FAST but UPDATE_TYPE_MED instead. DC needs dc_plane_info
and dc_plane_size to make this determination and we aren't currently
passing this into DC during atomic check.
Underflow (visible or non-visible) can occur if we don't validate this
correctly. This also will generally trigger p-state warnings, typically
via the cursor handler when locking.
[How]
Get the framebuffer tiling flags and generate the required structures
for DC in dm_determine_update_type_for_commit.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing navi12 asic ids.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
They are used by DC to determine ASIC revs.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DRM private objects have no hw_done/flip_done fencing mechanism on their
own and cannot be used to sequence commits accordingly.
When issuing commits that don't touch the same set of hardware resources
like page-flips on different CRTCs we can run into the issue below
because of this:
1. Client requests non-blocking Commit #1, has a new dc_state #1,
state is swapped, commit tail is deferred to work queue
2. Client requests non-blocking Commit #2, has a new dc_state #2,
state is swapped, commit tail is deferred to work queue
3. Commit #2 work starts, commit tail finishes,
atomic state is cleared, dc_state #1 is freed
4. Commit #1 work starts,
commit tail encounters null pointer deref on dc_state #1
In order to change the DC state as in the private object we need to
ensure that we wait for all outstanding commits to finish and that
any other pending commits must wait for the current one to finish as
well.
We do this for MEDIUM and FULL updates. But not for FAST updates, nor
would we want to since it would cause stuttering from the delays.
FAST updates that go through dm_determine_update_type_for_commit always
create a new dc_state and lock the DRM private object if there are
any changed planes.
We need the old state to validate, but we don't actually need the new
state here.
[How]
If the commit isn't a full update then the use after free can be
resolved by simply discarding the new state entirely and retaining
the existing one instead.
With this change the sequence above can be reexamined. Commit #2 will
still free Commit #1's reference, but before this happens we actually
added an additional reference as part of Commit #2.
If an update comes in during this that needs to change the dc_state
it will need to wait on Commit #1 and Commit #2 to finish. Then it'll
swap the state, finish the work in commit tail and drop the last
reference on Commit #2's dc_state.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204181
Fixes: 004b3938e6 ("drm/amd/display: Check scaling info when determing update type")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
By passing through the dm_determine_update_type_for_commit for atomic
commits that can be done asynchronously we are incurring a
performance penalty by locking access to the global private object
and holding that access until the end of the programming sequence.
This is also allocating a new large dc_state on every access in addition
to retaining all the references on each stream and plane until the end
of the programming sequence.
[How]
Shift the determination for async update before validation. Return early
if it's going to be an async update.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We previously allowed framebuffer swaps as async updates for cursor
planes but had to disable them due to a bug in DRM with async update
handling and incorrect ref counting. The check to block framebuffer
swaps has been added to DRM for a while now, so this check is redundant.
The real fix that allows this to properly in DRM has also finally been
merged and is getting backported into stable branches, so dropping
this now seems to be the right time to do so.
[How]
Drop the redundant check for old_fb != new_fb.
With the proper fix in DRM, this should also fix some cursor stuttering
issues with xf86-video-amdgpu since it double buffers the cursor.
IGT tests that swap framebuffers (-varying-size for example) should
also pass again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using a static int array will cause errors if the given dm_pp_clk_type
is out-of-bounds. For robustness, use a switch table, with a default
case to handle all invalid values.
v2: 0 is a valid clock type for smu_clk_type. Return SMU_CLK_COUNT
instead on invalid mapping.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang warns:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_pp_smu.c:336:8:
warning: implicit conversion from enumeration type 'enum smu_clk_type'
to different enumeration type 'enum amd_pp_clock_type'
[-Wenum-conversion]
dc_to_smu_clock_type(clk_type),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_pp_smu.c:421:14:
warning: implicit conversion from enumeration type 'enum
amd_pp_clock_type' to different enumeration type 'enum smu_clk_type'
[-Wenum-conversion]
dc_to_pp_clock_type(clk_type),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
There are functions to properly convert between all of these types, use
them so there are no longer any warnings.
Fixes: a43913ea50 ("drm/amd/powerplay: add function get_clock_by_type_with_latency for navi10")
Fixes: e5e4e22391 ("drm/amd/powerplay: add interface to get clock by type with latency for display (v2)")
Link: https://github.com/ClangBuiltLinux/linux/issues/586
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We were previously forcing the uclk for every state to max and reducing
the switch time to prevent uclk switching from occuring. This workaround
was previously needed in order to avoid hangs + underflow under certain
display configurations.
Now that DC has the proper fix complete we can drop the hacks and
improve power for most display configurations.
[How]
We still need the function pointers hooked up to grab the real uclk
states from pplib. The rest of the prior hack can be reverted.
The key requirements here are really just DC support, updated firmware,
and support for disabling p-state support when needed in pplib/smu.
When these requirements are met uclk switching works without underflow
or hangs.
Fixes: 02316e963a ("drm/amd/display: Force uclk to max for every state")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to support uclk switching on NV10 the SOC bounding box
needs to be updated.
[How]
We currently read the constants from the gpu info FW, but supporting
workarounds in DC for different versions of the FW adds additional
complexity to the codebase.
NV10 has been released so it's cleanest to keep the bounding box and
source code in sync by embedding the bounding box like we do for
other ASICs.
Fixes: 02316e963a ("drm/amd/display: Force uclk to max for every state")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
provide the interface for DAL to disable uclk switch on navi10.
in this case, the uclk will be fixed to maximum.
this is a workaround when display configuration causes underflow issue.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some code was missing the CONFIG_DRM_AMD_DC_DSC_SUPPORT guard.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add restriction to dissallow GTT domain if the relevant BO
doesn't have USWC flag set to avoid the APU hang scenario.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
enables gpu_vm_support in dm and adds
AMDGPU_GEM_DOMAIN_GTT as supported domain
v2:
Move BO placement logic into amdgpu_display_supported_domains
v3:
Use amdgpu_bo_validate_uswc in amdgpu_display_supported_domains.
v4:
amdgpu_bo_validate_uswc moved to sepperate patch.
Signed-off-by: Shirish S <shirish.s@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the allocation of config may fail and a null pointer
dereference on config can occur. Fix this by added a null
check on a failed allocation of config.
Addresses-Coverity: ("Dereference null return")
Fixes: c2cd9d04ec ("drm/amd/display: Hook up calls to do stereo mux and dig programming to stereo control interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
arch/x86/Makefile disables SSE and SSE2 for the whole kernel. The
AMDGPU drivers modified in this patch re-enable SSE but not SSE2. Turn
on SSE2 to support emitting double precision floating point instructions
rather than calls to non-existent (usually available from gcc_s or
compiler_rt) floating point helper routines for Clang.
This was originally landed in:
commit 1011745073 ("drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines")
but reverted in:
commit 193392ed9f ("Revert "drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines"")
due to bugreports from GCC builds. Add guards to only do so for Clang.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=109487
Link: https://github.com/ClangBuiltLinux/linux/issues/327
Suggested-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hi Linus,
Please, pull the following patches that mark switch cases where we are
expecting to fall through. These patches are part of the ongoing efforts
to enable -Wimplicit-fallthrough. Most of them have been baking in linux-next
for a whole development cycle.
Also, pull the Makefile patch that globally enables the
-Wimplicit-fallthrough option.
Finally, some missing-break fixes that have been tagged for -stable:
- drm/amdkfd: Fix missing break in switch statement
- drm/amdgpu/gfx10: Fix missing break in switch statement
Notice that with these changes, we completely get rid of all the
fall-through warnings in the kernel.
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----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=J2sO
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull Wimplicit-fallthrough enablement from Gustavo A. R. Silva:
"This marks switch cases where we are expecting to fall through, and
globally enables the -Wimplicit-fallthrough option in the main
Makefile.
Finally, some missing-break fixes that have been tagged for -stable:
- drm/amdkfd: Fix missing break in switch statement
- drm/amdgpu/gfx10: Fix missing break in switch statement
With these changes, we completely get rid of all the fall-through
warnings in the kernel"
* tag 'Wimplicit-fallthrough-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
Makefile: Globally enable fall-through warning
drm/i915: Mark expected switch fall-throughs
drm/amd/display: Mark expected switch fall-throughs
drm/amdkfd/kfd_mqd_manager_v10: Avoid fall-through warning
drm/amdgpu/gfx10: Fix missing break in switch statement
drm/amdkfd: Fix missing break in switch statement
perf/x86/intel: Mark expected switch fall-throughs
mtd: onenand_base: Mark expected switch fall-through
afs: fsclient: Mark expected switch fall-throughs
afs: yfsclient: Mark expected switch fall-throughs
can: mark expected switch fall-throughs
firewire: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable -Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Implement late_register and early_unregister hooks for MST connectors.
Call drm helpers for MST connector registration, which registers the
AUX devices.
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190723232808.28128-10-sunpeng.li@amd.com
Set the connector's kernel device as the parent for the aux kernel
device. This allows udev rules to access connector attributes when
creating symlinks to aux devices.
For example, the following udev rule:
SUBSYSTEM=="drm_dp_aux_dev", SUBSYSTEMS=="drm", ATTRS{edid}=="*",
SYMLINK+="drm_dp_aux/by-name/$id"
Will create the following symlinks using the connector's name:
$ ls /dev/drm_dp_aux/by-name/
card0-DP-1 card0-DP-2 card0-DP-3
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190723232808.28128-6-sunpeng.li@amd.com
[Why]
In an effort to stop redundant calls to dce110_disable_audio_stream
the audio->enabled flag was added to the audio resource struct. While
this state probably shouldn't have been tracked on the audio struct
itself it still works fine for some sequences.
However, it does not work for cases where we're freeing the audio
resource (such as hotplugs) or when dynamic audio is enabled.
In these cases the pipe_ctx->stream_res.audio = NULL before we can
set audio->enabled = false. The next time we acquire the audio resource
such as on hotplug the audio will not be enabled for the stream since
DC thinks it's still enabled.
Audio state tracking should cover this sequence.
[How]
Set audio->enabled = false at the start as long as we have
pipe_ctx->stream_res.audio.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
Some active dongles have DP++ port and DP port at the same time. Current
code doesn't cover DP++ case and processes as default DVI case, in which
audio is disabled. Because of dual mode, DP case is also treat as DVI case
for the other port.
[How]:
According DP 1.4 spec, add DP++ procedure similar with HDMI case. Also
add None dongle type for DP case.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC configures the GSL group for the pipe when pipe_split is enabled
and we're switching flip types (buffered <-> immediate flip) on DCN2.
In order to record what GSL group the pipe is using DC stores it in
the pipe's stream_res. DM is not aware of this internal grouping, nor
is DC resource.
So when DM creates a dc_state context and passes it to DC the current
GSL group is lost - DM never knew about it in the first place.
After 3 immediate flips we run out of GSL groups and we're no longer
able to correctly perform *any* flip for multi-pipe scenarios.
[How]
The gsl_group needs to be copied to the new context.
DM has no insight into GSL grouping and could even potentially create
a brand new context without referencing current hardware state. So this
makes the most sense to have happen in DC.
There are two places where DC can apply a new context:
- dc_commit_state
- dc_commit_updates_for_stream
But what's shared between both of these is apply_ctx_for_surface.
This logic only matters for DCN2, so it can be placed in
dcn20_apply_ctx_for_surface. Before doing any locking (where the GSL
group is setup) we can copy over the GSL groups before committing the
new context.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersen.wu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a flag to dc_debug_options to determine if a disconnected edp link
should be destroyed.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For some platforms, we need to know SMU version for driver/SMU
compatibility. This change adds that field.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Existing support in DC for pstate only accounts for a single latency. This is sufficient when the
variance of latency is small, or that pstate support isn't necessary for correct ASIC functionality.
Newer ASICs violate both existing assumptions. PState support is mandatory of correct ASIC
functionality, but not all latencies have to be supported. Existing code supports a "full p state" which
allows memory clock to change, but is hard for DCN to support (as it requires very large buffers).
New code will now fall back to a "dummy p state" support when "full p state" cannot be support.
This easy p state support should always be allowed.
[how]
Define a new latency in socBB. Add fallback logic to support it. Note DML is also updated to ensure
that fallback will always work.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN2x asic, the MPCC status register definition changed, and
our logic for assert is incorrect. disabled is valid state,
where we should see idle and not busy, where as in not
disabled state, we should see not idle.
[How]
Change assert condition to be more sensible.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously assume eDP sink present if connector present. Do not
need to enforce this restriction. Fix issue where driver attempt
to read link setting even though no edp connected.
{How]
Only read link setting after reading connection status.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES)
but the max number of audio devices (num_audio) is 7. In some projects,
it will run out of audios array.
[How]
Incraese the audios array size to 7.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For boards that support eDP but do not have a physical eDP
display connected an ASSERT will be thrown. This is not a
critical failure and shouldn't be treated as such.
[How]
Drop the assertion.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In an effort to stop redundant calls to dce110_disable_audio_stream
the audio->enabled flag was added to the audio resource struct. While
this state probably shouldn't have been tracked on the audio struct
itself it still works fine for some sequences.
However, it does not work for cases where we're freeing the audio
resource (such as hotplugs) or when dynamic audio is enabled.
In these cases the pipe_ctx->stream_res.audio = NULL before we can
set audio->enabled = false. The next time we acquire the audio resource
such as on hotplug the audio will not be enabled for the stream since
DC thinks it's still enabled.
Audio state tracking should cover this sequence.
[How]
Set audio->enabled = false at the start as long as we have
pipe_ctx->stream_res.audio.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Code to enable DCN20 dynamic metadata feature is duplicated in two places
and was added to DCE110 enable stream.
[How]
Create DCN20 specific enable stream function for clarity, and add a hardware
sequencer function to program dynamic metadata to avoid the duplicate
code.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dm_helpers_parse_edid_caps, there is a corner case where no speakers
can be allocated even though the audio mode count is greater than 0.
Enabling audio when no speaker allocations exists can cause issues in
the video stream.
[How]
Add a check to not enable audio unless one or more speaker allocations
exist (since doing this can cause issues in the video stream).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is possible (but very unlikely) that constructing dc fails
before current_state is created.
We support 666 color depth in some scenarios, but this
isn't handled in get_norm_pix_clk. It uses exactly the
same pixel clock as the 888 case.
[How]
Check for non null current_state before destructing.
Add case for 666 color depth to get_norm_pix_clk to
avoid assertion.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
update_bounding_box calculates intermediate bb states based on clock relationship
however, the last state doesn't need to maintain a minimum relationship, but should
actually contain maximum of every clock. otherwise maximum clocks are not usable
[how]
once the calculated bb is built, override the last state with max values
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add dual plane dcc programming support for
surfaces.
Removes unions from plane size and dcc params as they
serve no practical purpose only making our code
more convoluted. This results in easy dual plane
dcc and surface size programming.
Temporary diags_dm code is used to handle the interface
change without breaking functionality as a diags change
needs to be applied after this one.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Users want to not have filtering when scaling by integer
multiples to native timing.
[HOW]
If timing is a multiple integer of view, we set number of taps
to 1 (effectivly closest neighbour).
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
need to verify the impact of spatial dithering on 8bpc bypass mode.
[How]
added CRC sources and configure dihter option from dc stream.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: Hanghong Ma <Hanghong.Ma@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows to set a minimum display and dpp clock on dcn2+ HW
by adjusting clocks used for dml calculations.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
This is for HW negative stress testing use.
force reset the dispclk and dppclk even the same clock already set in HW.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
id_to_offset does not point to the same reg offset that offset_to_id checks for,
causing unintended asserts
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add dc_set_clock
add dc_get_clock
this is for testing and diagnostics to get/set DPPCLK and DISPCLK.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver will create 0, 1, and 2 ddc engines for RV2,
but some platforms used 0, 1, and 3.
[How]
Still allocate 4 ddc engines for RV2.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Implementation of stereo mux register is complete, but unused. Need to
call functions to write relevant configs.
[How]
Add function to write stereo config for enable/disable case and call in
stereo control interface.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Alpha could be improperly applied (only affecting half the
frame) for some source pixel formats.
[How]
Change how alpha is enabled in MPC/DPP LB and change the
bottom plane blend mode in MPC.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For clarity, save the use_pitch_c logic to a bool
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <eric.bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add this register for future use
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
bypass CM block and MPC ogam for debug or triage use.
[How]
create a new flag cm_bypass_mode, which will set both CM_CONTROL
and MPCC_OGAM_MODE to bypass when set to 1.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Number of 3DLUT's in MPC are not equal to number of pipes.
Resource management is required.
Activate on FPGA entire tm solution which includes
the following :hdr multiplier, shaper, 3dlut.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Gary Kattan <Gary.Kattan@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want a debug option to disable timing sync for testing.
[How]
New dc debug option that must be false to call program_timing_sync
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
As a fail-safe, in case 'set FEC_READY' DPCD write fails, a HW shadow
register should be cleared and the internal FEC stat should be set to
'not ready'. This is to make sure HW settings will be consistent with
FEC_READY state on the RX.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
1. Stack usage is pretty high as fixed31_32 struct is 8 bytes and we
have functions with >30 vars on the stack.
2. Optimize gamma calculation by reducing number of calls to
dc_fixpt_pow Our X points are divided into 32 regions wth 16 pts each.
Each region is 2x the previous, meaning x[i] = 2*x[i-16] for i>=16.
Using (2x)^gamma = 2^gamma * x^gamma, we can recursively compute powers
of gamma, we just need first 16 pts to start it up. dc_fixpt_pow() is
expensive, it computes x^y by doing exp(y*logx) Exp is done by Taylor
series approximation, and log by Newton-like approximation that also
uses exp internally. In short, it's significantly heavier than
run-of-the-mill addition/subtraction/multiply.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot optimization removed proper front end power off sequence.
In driver disable enable case, this causes driver to power gate hubp
and dpp while there is still memory fetching going on, this can cause
invalid memory requests to be generated which will hang data fabric.
[How]
Put back proper front end power off sequence
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Right now we FEC_READY is set only before the final link training,
i.e. at mode set time. This means FEC_READY won't be set when doing
link training as a response to HPD. It also fails UCD400 FEC test in
DP compliance.
[how]
Move FEC_READY setup to link training.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use helper to determine if HDMI signal when processing avmute.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Logic & structures for generic regs does not exist in DC currently.
[How]
Implement register masks/shifts and relevant functions for generic mux,
similar to existing HPD and DDC objects.
V2: fix includes for kalloc/free (Alex)
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In pipe split issue occurs when we program immediate flip while vsync flip is pending
[how]
Don't program immediate flip until flip is no longer pending
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display's hsync width is lower than the minimum dcn20 is set
to support right now. This will cause optc1_validate_timing to fail which
eventually will result in wrong set mode. This was set to 8 as per
HW team's request for no valid reason.
[How]
Changing min_h_sync_width to 4 will let us validate timing for
preffered mode and light up the headset. This change was made
to Vega 10 before for a similar issue.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We initialize pp_smu twice
[how]
Remove second initialization of pp_smu
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dcn20_clk_mgr_construct was not initializing pp_smu, and PME call gets
filtered out by the null check
[how]
initialize pp_smu dcn20_clk_mgr_construct
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some platforms, the encoder id 3 is not populated. So the encoders
are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This
would cause encoders id 4 & id 5 to fail when finding corresponding
audio device, defaulting to the first available audio device. As result,
we cannot stream audio into two DP ports with encoders id 4 & id 5.
[How]
It need to create enough audio device objects (0 - 5) to perform matching.
Then use encoder engine id to find matched audio device.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
link_stream is never NULL here as we've dereferenced it a couple lines before
and have done so for a couple months now.
[How]
- Drop the NULL check.
- Initialize where we know link_stream is non-NULL
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Do not fill Null packet in the blank period for new packet gen
This is based on HW IP team recommended default setting change.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When the system is going into suspend, set_backlight gets called
after the eDP got blanked. Since smooth brightness is enabled,
the driver will make a call into the DMCU to ramp the brightness.
The DMCU would try to enable ABM to do so. But since the display is
blanked, this ends up causing ABM1_ACE_DBUF_REG_UPDATE_PENDING to
get stuck at 1, which results in a dead lock in the DMCU firmware.
[how]
Disable brightness ramping when the eDP display is blanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we recover from hang, we do not want to skip the audio enable call.
[How]
Disable audio in dc_reinitialize_hardware
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DSC should be powered-on only on as-needed basis, i.e. if the mode
requires it
[how]
Loop over all the DSCs at driver init time and power-gate each
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current default is sufficient for a flag that does not change.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When launch D10.2, driver will write DPCD 0x107 with 0x00
[How]
Read MAX_DOWNSPREAD (0x0003h) then keep in current
link settings
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A hubp pointer was being passed to DCN1 functions, which
expect the enclosing structure (for the purpose of container_of macros)
to be dcn10_hubp, but the actual type was dcn20_hubp.
[How]
Copy existing DCN1 functions and alter them slightly for use with
dcn20_hubp.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before accessing it's vtable, check that stream_encoder is non-null.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to implement register programming for HDR dynamic
metadata transmission and tests.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently we don't wait for blacklight programming completion in DMCU
when setting backlight level. Some sequences such as PSR static screen
event trigger reprogramming requires it to be complete.
[How]
Add generic wait for dmcu command completion in set backlight level.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to check the pipe crc source through debugfs for bypass mode test.
[How]
add implementation of amdgpu_dm_crtc_get_crc_sources and hook into drm_crtc
callback get_crc_sources.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to compare DPRX CRCs with framebuffer CRCs for digital bypass mode.
[How]
Hook into DRM to grab DP receiver CRCs through drm_dp_start_crc.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardware docs state that we must wait until the GPUVM context is ready
after programming it.
[How]
Poll until the valid bit of PAGE_TABLE_BASE_ADDR_LO32 is set to 1 after
programming it.
v2: fix include for udelay (Alex)
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Specifically to one panel,
TCON is able to accept active video signal quickly, but
the Source Driver requires 2-3 frames of extra time.
It is a Panel issue since TCON needs to take care of
all Sink requirements including Source Driver. But in
this case it does not.
Customer is asking to add fixed T7 delay as panel
workaround.
[How]
Add monitor specific patch to add T7 delay
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds EMP packet programming for enabling dsc with
hdmi. The packets are structured according to VESA HDMI 2.1x
r2 spec, section 10.10.2.2.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
for 2 purposes:
1. get raw register value dumped on the log, which will make it easier
to talk to other team who only knows about the register
2. enable other HW to be able to use the same interface as raven to log
clock register data
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current code will not wait for the entire frame
after global unlock.
This causes dsc dynamic target bpp update corruption when
there is a surface update immediately happens after this.
[how]
Wait for the entire whole frame after unlock before continuing
the rest of stream and surface update.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-Pass and use pixel clock in 100 Hz to Audio for HDMI
audio DTO for Audio wall clock programming so audio DTO gets
increased precision for timings with /1001 factor.
-For HDMI TMDS for N and CTS ACR tables are based on 10 KHz
units, these does not need to be modified as N and CTS values
are still valid using current tables.
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DCE110, DCE112 and DCE120 the max_clks_by_state for the clk_mgr are
copied from their respective table before the call to
dce_clk_mgr_construct, but then dce_clk_mgr_construct overwrites
these with the dce80_max_clks_by_state.
[How]
Copy these after we call dce_clk_mgr_construct so we're using the
right tables.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We reset the optimized_required in atomic_plane_disable
flag immediately after it is set in atomic_plane_disconnect, causing us to
never have flag set during next flip in UpdatePlanes.
[how]
Optimize directly after each time plane is removed.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
TRAINING_AUX_RD_INTERVAL (DPCD 000Eh) modifies the read interval
for the EQ training sequence. CR read interval should remain 100 us.
Currently, the CR interval is also being modified.
[HOW]
lt_settings->cr_pattern_time should always be 100 us.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are shared regs and code across DCN generations. Pull them out
into a shared common location.
Also, expose some dcn20 init functions.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fixes issue when we have a display connected using a passive
dongle and then emulate over it using a DP connection at 1 x 1.62 Ghz.
System hangs because register bus returns back 0xFFFFFFFF for all
register reads after setting register DIG_BE_CNTL in
dcn10_link_encoder_connect_dig_be_to_fe(). Hang occurs later
when trying to do a register read.
[How]
At the start of the emulation, dc_link_set_preferred_link_settings()
and dp_retrain_link_dp_test() is called, even though it is connected
using a passive dongle.
Add an extra condition in dp_retrain_link_dp_test() to check for
link->dongle_max_pix_clk > 0. This is the only way we know if the
connection is using passive dongle so we don't retrain DP.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently logical values are swapped in HW, causing
system aperture to be undefined, so VA and PA cannot co-exist
[how]
program values correctly
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
'second_line_offset_adj' was mistakenly left at zero, even though DSC spec
v1.2a recommends setting this field to 512 for 4:2:0.
[how]
Set 'second_line_offset_adj' to 512 for 4:2:0 and leave at zero otherwise
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We're not expected to enter the default case, but not returning a
default value here is incorrect.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unintentionally introduced behaviour change from previous refactor,
which causes clks to be 0 in no stream cases, which will cause
divide by 0.
[How]
Skip calculation of clocks when no stream. Which is the same as old
behaviour.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <tong.cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some parts of the DSC spec relating to 4.2.0 were not reflected in
drm_dsc_compute_rc_parameters, causing unexpected config failures
[How]
Add nsl_bpg_offset and rbs_min computation
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dce was re-arch'd, therefore adding aux tracing log into new dce
[How]
The porting from submit_channel_request/process_channel_reply of aux_engine_dce110.c
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <tong.cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.
[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching
[how]
Use existing override logic. If override not defined, then force
min = 507
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For better readability and reusability
[How]
Move snippets of BW calculation code into helpers.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A regression caused dsc to never get disabled in certain situations.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some values were not being converted or bit-shifted properly for
HW registers, causing black screen
[how]
Fix up the values before programming HW
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To add support for OS requirement to set preferred link training
parameters.
[HOW]
Create new structure of dp link training overrides. During link training
processes, these values should be used instead of the default training
parameters.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On some modes SMU will be in infinite loop state at boot, this is
because driver assumes p_state_support is false, but this is the
opposite of the assumed boot state by SMU. we optimize away
notifying SMU about no pstate, and so they will get stuck
[how]
when we init clk manager, init pstate to true, so it matches driver load
assumption
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
not needed for navi14 at the moment.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change the pipes to 5 if the asic is nv14
This is a temp patch, there was some refactor in the dml part of the code.
which is not in this branch. for now this is good, we can implement this
properly once we have an updated branch.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
Some active dongles have DP++ port and DP port at the same time. Current
code doesn't cover DP++ case and processes as default DVI case, in which
audio is disabled. Because of dual mode, DP case is also treat as DVI case
for the other port.
[How]:
According DP 1.4 spec, add DP++ procedure similar with HDMI case. Also
add None dongle type for DP case.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously assume eDP sink present if connector present. Do not
need to enforce this restriction. Fix issue where driver attempt
to read link setting even though no edp connected.
{How]
Only read link setting after reading connection status.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES)
but the max number of audio devices (num_audio) is 7. In some projects,
it will run out of audios array.
[How]
Incraese the audios array size to 7.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For boards that support eDP but do not have a physical eDP
display connected an ASSERT will be thrown. This is not a
critical failure and shouldn't be treated as such.
[How]
Drop the assertion.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dm_helpers_parse_edid_caps, there is a corner case where no speakers
can be allocated even though the audio mode count is greater than 0.
Enabling audio when no speaker allocations exists can cause issues in
the video stream.
[How]
Add a check to not enable audio unless one or more speaker allocations
exist (since doing this can cause issues in the video stream).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is possible (but very unlikely) that constructing dc fails
before current_state is created.
We support 666 color depth in some scenarios, but this
isn't handled in get_norm_pix_clk. It uses exactly the
same pixel clock as the 888 case.
[How]
Check for non null current_state before destructing.
Add case for 666 color depth to get_norm_pix_clk to
avoid assertion.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver will create 0, 1, and 2 ddc engines for RV2,
but some platforms used 0, 1, and 3.
[How]
Still allocate 4 ddc engines for RV2.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot optimization removed proper front end power off sequence.
In driver disable enable case, this causes driver to power gate hubp
and dpp while there is still memory fetching going on, this can cause
invalid memory requests to be generated which will hang data fabric.
[How]
Put back proper front end power off sequence
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In pipe split issue occurs when we program immediate flip while vsync flip is pending
[how]
Don't program immediate flip until flip is no longer pending
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display's hsync width is lower than the minimum dcn20 is set
to support right now. This will cause optc1_validate_timing to fail which
eventually will result in wrong set mode. This was set to 8 as per
HW team's request for no valid reason.
[How]
Changing min_h_sync_width to 4 will let us validate timing for
preffered mode and light up the headset. This change was made
to Vega 10 before for a similar issue.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some platforms, the encoder id 3 is not populated. So the encoders
are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This
would cause encoders id 4 & id 5 to fail when finding corresponding
audio device, defaulting to the first available audio device. As result,
we cannot stream audio into two DP ports with encoders id 4 & id 5.
[How]
It need to create enough audio device objects (0 - 5) to perform matching.
Then use encoder engine id to find matched audio device.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When the system is going into suspend, set_backlight gets called
after the eDP got blanked. Since smooth brightness is enabled,
the driver will make a call into the DMCU to ramp the brightness.
The DMCU would try to enable ABM to do so. But since the display is
blanked, this ends up causing ABM1_ACE_DBUF_REG_UPDATE_PENDING to
get stuck at 1, which results in a dead lock in the DMCU firmware.
[how]
Disable brightness ramping when the eDP display is blanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we recover from hang, we do not want to skip the audio enable call.
[How]
Disable audio in dc_reinitialize_hardware
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When launch D10.2, driver will write DPCD 0x107 with 0x00
[How]
Read MAX_DOWNSPREAD (0x0003h) then keep in current
link settings
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before accessing it's vtable, check that stream_encoder is non-null.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently we don't wait for blacklight programming completion in DMCU
when setting backlight level. Some sequences such as PSR static screen
event trigger reprogramming requires it to be complete.
[How]
Add generic wait for dmcu command completion in set backlight level.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardware docs state that we must wait until the GPUVM context is ready
after programming it.
[How]
Poll until the valid bit of PAGE_TABLE_BASE_ADDR_LO32 is set to 1 after
programming it.
v2: fix include for udelay (Alex)
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current code will not wait for the entire frame
after global unlock.
This causes dsc dynamic target bpp update corruption when
there is a surface update immediately happens after this.
[how]
Wait for the entire whole frame after unlock before continuing
the rest of stream and surface update.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DCE110, DCE112 and DCE120 the max_clks_by_state for the clk_mgr are
copied from their respective table before the call to
dce_clk_mgr_construct, but then dce_clk_mgr_construct overwrites
these with the dce80_max_clks_by_state.
[How]
Copy these after we call dce_clk_mgr_construct so we're using the
right tables.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We reset the optimized_required in atomic_plane_disable
flag immediately after it is set in atomic_plane_disconnect, causing us to
never have flag set during next flip in UpdatePlanes.
[how]
Optimize directly after each time plane is removed.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fixes issue when we have a display connected using a passive
dongle and then emulate over it using a DP connection at 1 x 1.62 Ghz.
System hangs because register bus returns back 0xFFFFFFFF for all
register reads after setting register DIG_BE_CNTL in
dcn10_link_encoder_connect_dig_be_to_fe(). Hang occurs later
when trying to do a register read.
[How]
At the start of the emulation, dc_link_set_preferred_link_settings()
and dp_retrain_link_dp_test() is called, even though it is connected
using a passive dongle.
Add an extra condition in dp_retrain_link_dp_test() to check for
link->dongle_max_pix_clk > 0. This is the only way we know if the
connection is using passive dongle so we don't retrain DP.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently logical values are swapped in HW, causing
system aperture to be undefined, so VA and PA cannot co-exist
[how]
program values correctly
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
'second_line_offset_adj' was mistakenly left at zero, even though DSC spec
v1.2a recommends setting this field to 512 for 4:2:0.
[how]
Set 'second_line_offset_adj' to 512 for 4:2:0 and leave at zero otherwise
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We're not expected to enter the default case, but not returning a
default value here is incorrect.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.
[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching
[how]
Use existing override logic. If override not defined, then force
min = 507
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A regression caused dsc to never get disabled in certain situations.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some values were not being converted or bit-shifted properly for
HW registers, causing black screen
[how]
Fix up the values before programming HW
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On some modes SMU will be in infinite loop state at boot, this is
because driver assumes p_state_support is false, but this is the
opposite of the assumed boot state by SMU. we optimize away
notifying SMU about no pstate, and so they will get stuck
[how]
when we init clk manager, init pstate to true, so it matches driver load
assumption
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] dc sw clock implementation of navi10 and raven are not exact the
same. dcccg, dchub reference clock initialization is done after dc calls
vbios dispcontroller_init table. for raven family, before
dispcontroller_init is called by dc, the ref clk values are referred
by sw clock implementation and program asic register using wrong
values. this causes dchub pstate error. This need provide valid ref
clk values. for navi10, since dispcontroller_init is not called,
dchubbub_global_timer_enable = 0, hubbub2_get_dchub_ref_freq will
hit aeert. this need remove hubbub2_get_dchub_ref_freq from this
location and move to dcn20_init_hw.
[HOW] for all asic, initialize dccg, dchub ref clk with data from
vbios firmware table by default. for raven asic family, use these data
from vbios, for asic which support sw dccg component, like navi10,
read ref clk by sw dccg functions and update the ref clk.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Workaround for now to avoid underflow.
The uclk switch time should really be bumped up to 404, but doing so
would expose p-state hang issues for higher bandwidth display
configurations.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang complains that 'false' is a not a pointer:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_resource.c:2428:10: error: expression which evaluates to zero treated as a null pointer constant of type 'struct pipe_ctx *' [-Werror,-Wnon-literal-null-conversion]
return false;
Changing it to 'NULL' looks like the right thing that will shut up
the warning and make it easier to read, while not changing behavior.
Fixes: 7ed4e6352c ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As previously fixed for dml in commit 4769278e5c ("amdgpu/dc/dml:
Support clang option for stack alignment") and calcs in commit
cc32ad8f55 ("amdgpu/dc/calcs: Support clang option for stack
alignment"), dcn20 uses an option that is not available with clang:
clang: error: unknown argument: '-mpreferred-stack-boundary=4'
scripts/Makefile.build:281: recipe for target 'drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_resource.o' failed
Use the same trick that we have in the other two files.
Fixes: 7ed4e6352c ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the clock is already logged, also log the voltage.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The drm_audio_component can be used to give pin ELD notifications
directly to the sound driver. This fixes audio endpoints disappearing
due to missing unsolicited notifications.
[How]
Send the notification via the audio component whenever we enable or
disable audio state on a stream. This matches what i915 does with
their drm_audio_component and what Takashi Iwai's proposed hack for
radeon/amdpgu did.
This is a bit delayed in when the notification actually occurs, however.
We wait until after all the programming is complete rather than sending
the notification mid sequence.
Particular care is needed for the get ELD callback since it can happen
outside the locking and fencing DRM does for atomic commits.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to give pin notifications to the sound driver from DM we need
to know whether audio is enabled on a stream and what pin it's using
from DC.
[How]
Expose the instance via stream status if it's a mapped resource for
the stream. It will be -1 if there's no audio mapped.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On 32-bit architectures, dividing a 64-bit integer in the kernel
leads to a link error:
ERROR: "__udivdi3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: "__divdi3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
Change the two recently introduced instances to a multiply+shift
operation that is also much cheaper on 32-bit architectures.
We can do that here, since both of them are really 32-bit numbers
that change a few percent.
Fixes: bedbbe6af4 ("drm/amd/display: Move link functions from dc to dc_link")
Fixes: f18bc4e53a ("drm/amd/display: update calculated bounding box logic for NV")
Acked-by: Slava Abramov <slava.abramov@amd.com>
Tested-by: Slava Abramov <slava.abramov@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without this header, we get a compiler error in some configurations:
.../dc/dcn20/dcn20_hwseq.c: In function 'dcn20_hwss_wait_for_blank_complete':
.../dc/dcn20/dcn20_hwseq.c:1493:3: error: implicit declaration of function 'udelay' [-Werror=implicit-function-declaration]
Note: the use of udelay itself may be problematic, as can occupy
the CPU for 200ms in a busy-loop here.
Fixes: 7ed4e6352c ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Reviewed-by: Christian König <Christian.Koenig@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All asics newer than vega10 use client ids, so simplify the
check.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are a couple of spelling mistakes in dm_error messages and
a comment. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The AVI infoframe is incorrectly programmed on DCN1/2 when enabling a
stream - causing the wrong pixel encoding to be used for display.
This is because the AVI infoframe is programmed before the DIG BE is
connected to the FE and turned on, so enabling the AFMT block doesn't
actually work and the registers subsequently can't be written to.
[How]
Program the infoframe *after* turning on the DIG FE. This was the
behavior previously used but it was incorrectly reverted
when adding the DCN2 HW sequencer code.
v2: Don't call update_info_frame twice
Fixes: 7ed4e6352c ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Inconsistent indentation and mixed use of brackets.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported by smatch:
amdgpu_dm.c:5637 amdgpu_dm_commit_planes() error: we previously assumed 'acrtc_state->stream' could be null
This seems to be checked for null pretty consistently elsewhere.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to protect the comments. The DCN1_01 config
was dopped anyway. Got accidently brought back with the
navi merge.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We may need to sleep for up to 80ms
(8ms per each of up to 10 loop iterations):
/* First DPCD read after VDD ON can fail if the particular board
* does not have HPD pin wired correctly. So if DPCD read fails,
* which it should never happen, retry a few times. Target worst
* case scenario of 80 ms.
*/
Switch udelay to msleep to avoid limits on arm.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
during navi10 bring up, dwb causes system hang.
to continue debug major issue, disable dwb by
set num-dwb = 0. the hang issue is not reproduced now
by enable num-dwb =1. dc source is shared by all os.
win needs num-dwb = 1.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before for raven and navi we are calling pp_smu functions for pme
[how]
refactor a code so we will call clk_mgr's enable_pme_wa function so we
can use pme_wa for future asics. This way we don't need to worry about
different ASIC since clk_mgr already have that information
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging underflow issues it can be useful to have asserts when the
underflow initially occurs.
[How]
Read the underflow status registers after actions that have a high risk
of causing underflow and assert that no underflow occurred. If underflow
occurred, clear the bit.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently vmid is decided internally inside dc. With the introduction
of new asics we are required to coordinate vmid use with external
components.
This change converts vmid logic to a DAL module allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
dcn2 use fixed clocks and not program DPP CLK or Disp_CLK.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
value commited to by HW team is going to be higher
than pre-silicon, and will cause underflow if driver not
updated
[how]
update hardcoded value, update pstate switching logic
to fix case where with long uclk time we won't allow switch
even when we should
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for the upcoming DRM plane color management properties
we need to correct a lot of wrong behavior and assumptions made for
CRTC color management.
The documentation added by this commit in amdgpu_dm_color explains
how the HW color pipeline works and its limitations with the DRM
interface.
The current implementation does the following wrong:
- Implicit sRGB DGM when no CRTC DGM is set
- Implicit sRGB RGM when no CRTC RGM is set
- No way to specify a non-linear DGM matrix that produces correct output
- No way to specify a correct RGM when a linear DGM is used
We had workarounds for passing kms_color tests but not all of the
behavior we had wrong was covered by these tests (especially when
it comes to non-linear DGM). Testing both DGM and RGM at the same time
isn't something kms_color tests well either.
[How]
The specifics for how color management works in AMDGPU and the new
behavior can be found by reading the documentation added to
amdgpu_dm_color.c from this patch.
All of the incorrect cases from the old implementation have been
addressed for the atomic interface, but there still a few TODOs for
the legacy one.
Note: this does cause regressions for kms_color@pipe-a-ctm-* over HDMI.
The result looks correct from visual inspection but the CRC no longer
matches. For reference, the test was previously doing the following:
linear degamma -> CTM -> sRGB regamma -> RGB to YUV (709) -> ...
Now the test is doing:
linear degamma -> CTM -> linear regamma -> RGB to YUV (709) -> ...
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This is meant to make it clearer that 0xf is not a valid OPP ID, and
that code making use of OPP IDs should not accept this value.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
expose this function for future use
Implementation of DCN3 DIO Link Encoder including
dpcs register headers.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add dwb stereo caps and ver for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add Alpha surface type for future use
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Existing behavior has overlapping ranges resulting in path
dependent SMU selection
[how]
Make ranges non-overlapping, resulting in non-path dependent
selection
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
According to the latest specs, the max_target bpp sink
can support is 16 bpp.
[how]
update dsc max_target_bpp to 16
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
required for new checks.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Current policy assumes virtual DPCD peer device as
an individual MST branch device with 1 input and 1 output.
However this is only true for virtual DP-to-DP peer device.
In general there are three types of virtual DP peer devices.
1. Sink peer device with virtual DPCD.
2. Virtual DP-to-DP Peer device with virtual DPCD.
3. Virtual DP-to-HDMI Protocol Converter Peer Device with
Virtual DPCD.
So we should break the assumption and handle all three types.
[how]
DP-to-DP peer device will have virtual DPCD cap upstream.
Sink peer device will have virtual DPCD on the logical port.
Dp to HDMI protocol converter peer device will have virtual DPCD
on its converter port.
For DSC capable Synaptics non VGA port we workaround by enumerating
a virutal DPCD peer device on its upstream
even if it doesn't have one.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
useful for debugging
[how]
plumb a debug option in dc
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Almost every function in DC that works with stream state expects that
the current state on the stream is the one that it should be writing
out. These functions are typically triggered by specifying a particular
stream update - but the actual contents of the stream update itself
are ignored, leaving it to the DM to actually update the stream state
itself.
The problem with doing this in DM is a matter of timing. On Linux
most of this is incorrectly done in atomic check, when we actually want
it to be done during atomic commit tail while access to DC is locked.
To give an example, a commit requesting to modify color management
state for DM could come in, be rejected, but still have modified
the actual system state for the stream since it's shared memory. The
next time color management gets programmed it'll use the rejected
color management info - which might not even still be around if it's
a custom transfer function.
So a reasonable place to perform this is within DC itself and this is
the model that's currently in use for surface updates. DC can even
compare the current system state to the incoming surface update to
determine update level, something that can't currnetly be done with the
framework for stream updates.
[How]
Duplicate the framework used for surface updates for stream updates
as well. Copy all the updates after checking the update type.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SwathWidthCThisState is expected to be an unsigned int array.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
when resetting pipes from 480p to dual-pipe 8k, modulo reg write for
video optimized rate updated one pipe without changing the other, causing
sync error
[how]
removed code from dcn2
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The output_bpp pipe parameter was assigned an incorrect value
(color depth enum), and subsequently used to overwrite
the OutputBpp parameter calculated by DML. Seems like this had no
effect except with DSC enabled, which would make DML produce
bad outputs.
[How]
Removed assignment to OutputBpp, fixed output_bpp assignment,
and properly set ForcedOutputLinkBPP instead of OutputBpp.
Also removed condition in DML that prevented forcing of
Output BPP with DSC enabled.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
VM implemenation is missing conversion from HW values in hubbub
DM not passing actual PTB during flip
[how]
add proper HW conversion from logical values
fix cases where we programmed VA even though we are in PA
plumb in PTB from DM
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes for the following:
- Incorrect pointer type (unsigned int instead of double)
- Incorrect DSC number of slices setting
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently DSC power gating is disabled by default because the power
transition doesn't happen, causing a crash on some systems
[how]
Fix the lack of power state transition and enable DSC power gating
by default.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Should do full update when display writeback is updated.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dsc adjustment is allowed via stream update sequence.
dsc enablement is only allowed via commit stream sequence.
with the current unified dsc set function, it is hard
to determine which sequence it is called by.
The solution is to decouple dsc adjustment out of enablement
sequence so we can handle them separately.
[how]
decouple dsc adjustment out of enablement.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
current DML logic uses currently trained setting for number
of dp lanes in DML calculations. this is obviously flawed since
just because 1 lane is in use doesn't mean only 1 lane can be used
this causes mode validation to fail depending on current state,
which is incorrect
[how]
DML should always assume 4 lanes are available. validation of
bandwidth is not supposed to be handled by DML, since we do
link validation without DML already
also, DML is expecting there to be a copy of the max state, this
state is removed when update_bounding_box is called to update
actual SKU clocks. fix this as well by duping last state.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN code should make as few references to DCE as possible
[HOW]
Copy DCE110 implementation of find_first_free_match_stream_enc_for_link
into DCN10
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
From DCE110 onward, we have the ability to assign DIG BE and FE
separately for any display connector type; before, we could only do this
for DP.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With DSC power gating enabled, one of the register reads times out occasionally,
causing a DSC test to fail.
[how]
Disable DSC power gating in Diags.
NOTE: This has to be reverted once the problems with DSC power gating are
resolved.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want a test pattern to show up on screen when we're blanked and have
visual confirm enabled, for debugging. Raven does this, it's a mistake that
Navi does not.
[How]
- in "blank_pixel_data", set appropriate DPG pattern for visual confirm
- refactor DPG calls out of "enable_stream_timing"
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
these enums/structs will be used more generically in the future
so moving it to dc_hw_types and dc_types
Signed-off-by: Tyler DiBattista <tyler.dibattista@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Reuse existent code path (dcn1+) and in order to do that apply de gamma
in 1D blender LUT and re use MPC OGAM.
Follow up is required.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Features that are desirable for minimizing the Global Sync Period:
DRR and lateflip
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In compute dsc bandwidth range there is an uninitialized variable
[how]
Initialize the variable to the correct value.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To send sdp message immediately from a single slot.
[How]
Modify the generic SDP message interface, and use GSP4 to send immediate
sdp message.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN2.0 LB BPP should be 48 or 16BPC and max cursor width should be 256.
Also use populate_dml_pipes as functions pointer instead of using it directly
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A regression was introduced when we set correct tile size
for the gfx9 swizzle mode. This resulted in incorrect
macro tile size.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Plane disable gets calls when we enable blank. On DCN2, we blank by using
DPG to display a black colour instead of using OTG blank. DPG runs off the
OPP clock, therefore we shouldn't disable the OPP clock when disabling the
plane. We do need to disable the OPP clock when disabling the entire pipe,
that will be addressed in a separate commit.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It looks like mpo isn't properly disabled during odm, this change is
meant to fix that.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dwb fixes.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
dcn20 has num_dwb =1 in the res cap, but not created.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GSL is being used to synchronize pipes when vsync is off but
on transition to vsync on during a mode change GSL is not
being reset correctly.
[How]
Disable GSL on any plane that is disabled.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A few of the new DSC DPCD caps were introduced by a DP 1.4a SCR in order
to give DSC branch decoders a chance to expose their maximum throughput
and maximum line width limitations.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If a set is done, DSC settings are zeroed out, leading to no DSC for the modes
that require ODM, such as 8k60.
This was a regression introduced by 5a4f26295176bbfc776c75aaf0f6dd8ccf806958.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Emulating passive dongle on USB-C port causes issue on some asics.
[How]
Check for DP_IS_USB_C flag in bios parser and propagate it to
encoder features flags. If DP_IS_USB_C flag is set and it is trying to
emulate passive dongle, then return fail.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DCHub arbiter has a mechanism to dynamically rate limit the DCHub
request stream to the fabric. If the memory controller is fully utilized
and the DCHub requestors are well ahead of their amortized schedule,
then it is safe to prevent the next winner from being committed and sent
to the fabric. The utilization of the memory controller is approximated
by ensuring that the number of outstanding requests is greater than a
threshold specified by the ARB_MIN_REQ_OUTSTANDING. To determine that
the DCHub requestors are well ahead of the amortized schedule, the slack
of the next winner is compared with the ARB_SAT_LEVEL in DLG RefClk
cycles.
[How]
The recommended settings to enable thise dynamic limiting for Navi is
180 requests.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It was missing, although defined in DP spec
[how]
- Add handling of this value to DSC code
- Also remove unused file dsc_helpers.c
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
This is for DC_I2c arbitration use between HW use/SW use and DMCU use.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
'Divide by zero' error happens when line size happens to be zero.
[how]
The code that makes sure line size minimum value can be 1 was already
present in DCN1 part of the driver, this is mearly a port to DCN2.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to ensure that incoming flips are latched and
complete immediately, we need to program the vupdate
interrupt to come during the back porch of each frame.
[How]
Program the vupdate start_line to be in the back porch
like it's done for DCN1.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The split condition is broken and will always activate
at the moment.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Different HW will need to init HUBP differently. For now, add a vtable
entry, and hook a NO-OP for DCN1 and DCN2.
In addition, future HW will need to access the HUBPREQ_DEBUG and
CUR_TTU_CNTL0 register for hubp_init. Add that here.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OPTC data format was left at its default value (444) when enabling
ODM combine. This caused issues with FPGA capture.
[How]
Write the OPTC_DATA_FORMAT field when enabling ODM combine.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the generic introduction of seamless boot, the display is no
longer blanked upon boot. However, this causes corruption on some
systems that does not lock the memory in the non-secure boot case,
resulting in brief corruption on boot due to garbage being written into
the frame buffer.
[How]
Add a flag, read during DC init, to determine whether display should be
blanked on boot. Default to true.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DSC target bpp precision is a decoder DPCD and an AMD encoder capability.
It must be taken into account when calculating target bitrate.
[how]
Add a DC DSC function that does this calculation.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ABM is currently not enabled on DCN2.
[How]
Update the register name list for DCN2 and un-comment the code that
creates the abm object.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current policy will always enable DSC to 12 bpp
regardless of if the current bandwidth is enough for MST displays.
This logic is not optimal because user will get lower quality output
if DSC compression is enabled.
This change to is to implement a DSC MST bandwidth fair share
algorithm so we will dynamically decide if DSC is needed and what
quality (target bpp) is needed to fairly destribute the MST bandwidth
in one MST topology. This will allow user to see the most optimal
image quality with the given bandwidth.
[how]
We will start with lowest bandwidth possible and run a
Max-Min fairness algorithm to fairly distribute the available
bandwidth. If there is still remaining bandwidth, we will try to fit
the timing without DSC compression.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There are ASICs that have fewer DSC engines than pipes, which makes
DSC a resource that should be used only if required.
[how]
Acquire DSC HW resource if required by stream and release when not
required anymore.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] system crash when initialize dwb
current linux driver does not support dwb.
disable this feature for now.
[HOW] set num_dwb = 0 to disable dwb for now
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] linux upstream already has interrupt vupdate for freesync
in dcn10. dcn20 interrupt shares the same source code as dcn10.
but dcn20 interrupt translator does not add vupdate interrupt.
this cause index of vupdate aarray be negative which causes
crash.
[HOW] add vupdate into dc interrupt transltor
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DSC resource has to be acquired before it can be used and simply copying
a reference to it is very likely to cause problems when accessing DSC.
[how]
Set DSC resource pointer to NULL to mark it as unused after primary pipe
resources were copied to the secondary ODM pipe.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some nightly tests are failing since the new value for fclk is a
bit too low. Also, a new test for the maximum downscale case was
needed.
[How]
Updated the default value for fclk to be 1.2GHz.
Signed-off-by: Tyler DiBattista <tyler.dibattista@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
when an update programming sequence requires both
front end and back end pipe to be updated synchronously,
a global update lock needs to be set to ensure that
we don't get a frame with only front end update but
not the back end update.
[how]
setup global lock parameters on enable_stream_timing.
enable global lock when pipe_control_lock_global is called.
disable global lock when pipe_control_lock is called.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some register fields are not needed.
[How]
remove them
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We used this change to investigate the performance of bandwidth validation,
it will be useful to have if we need to investigate further.
[How]
We use performance counter tick numbers to profile performance, they live
at dc->debug.bw_val_profile (set .enable in debugger to turn on measuring).
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can split validation into three parts: getting voltage level, getting
watermarks, and rq/dlg calculations. The voltage level is enough to answer
the question "do we support this state", and the rest of it is to determine
what hardware programming is needed to support the state. Most of the calls
to validate_bandwidth only care about the first part, so we added an early
return in that case
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
display_mode_vba is for DCN2 and up. When building for upstream (DCN1
enabled only), there will be a build error, since display_mode_vba.c/h
is stripped out.
Note that building DCN1 only with internal dal-dev is still fine, since
display_mode_vba.h is not stripped out internally - only in upstream.
The make directives therefore stll work, and so will any #include's.
[How]
Since subsequent generations require DCN2 enabled anyways, guard the
makefile directive for display_mode_vba.o with DCN2. Guard any includes
with DCN2. In addition, guard the entire contents of display_mode_vba.h
with DCN2, to simulate the file being stripped out in upstream.
A forward declaration for 'struct display_mode_lib' also needs to be
added in display_mode_lib.h. Previously, display_mode_vba.h contained
the forward declaration, and display_mode_lib.h in turn included it.
This won't work if mode_vba.h is stripped out, requring mode_lib.h to do
so itself.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Usage of this enum is DSC-only.
[How]
Guard it with CONFIG_DRM_AMD_DC_DSC_SUPPORT.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Can not turn on two displays at the same time with the asic having only one DSC.
DC_DSC_RESOURCE allocation failed.
[Solution]
Only add_dsc if the timing is dsc capable based on diag_dc and num_dsc
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If voltage level > 0, DCFCLK and SOCCLK could be 0 during DML
calculations, which ended up causing an assert.
[How]
Initialize dcfclk_mhz and socclk_mhz values according to the
voltage level.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Added some regs and exposed some functions for future use
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On at least some of the devices (e.g. Realtek scaler) we get a black screen if 1/16th
precision is used.
[how]
Work around it by reducing precision to 1/8th for N4:2:2 and 4:2:0 color formats. This
is a safe workaround and would have a very mild impact on the quality.
The issue is still to be root-caused and fixed correctly.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Global optic double buffer lock is currently disabled due to
incorrect programming sequence that affects non global lock.
[how]
Isolate global lock programming sequence out of non global lock
programming sequence, so it can be enabled without affecting
non global lock.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
This is now done in the original link bandwidth calculation and DSC
must not do this anymore.
[how]
Remove the line of code that should have been removed when transition
to correctly applying FEC overhead was made.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We shouldnt need overhead on top of dppclk when setting fclk.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Clean up some dsc legacy functions that are
no longer needed.
[how]
remove two dsc functions in dc_dsc, use dc_bandwidth_in_kbps_from_timing
instead of calc_required_bandwidth_for_timing.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn20_apply_ctx_for_surface can be called with 0 planes, which means we
should blank the display. In this case when we get down to
dcn20_setup_gsl_group_as_lock, pipe_ctx->plane_state is NULL, but we don't
check for it. However, this function is only called by
dcn20_pipe_control_lock, and in that function we alraedy have a local for
the immediate flip status, which is what we care about in the plane state.
[How]
- pass in immediate flip status as parameter
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently dsc is validated not taking the image width limitation into
mind.
This change addresses that, but due to previous design being limited
to non odm dsc validation additional sequence changes are made.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
u clk set request was being sent in units of mts, when it needed to be
in units of Mhz
[How]
add a division by 16 to convert from mts to Mhz
Signed-off-by: Aidan Wood <Aidan.Wood@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If num_states == 0 we did update_bound_box which doesn't updated any max
clocks if num_states == 0, therefore we need to do cap_soc_clocks
instead, also SMU cannot set DCF clock to a higher than or equal to freq
than SOC clock
[How]
Add a num_states != 0 check for update_bounding_box to be run, and after
we run get_maximum_sustainable_clocks we now check if the reported max
value of DCF is higher than SOC and if necessary set it to 1000
(becomes 1 after division by 1000) lower than SOC
Signed-off-by: Aidan Wood <Aidan.Wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently link bandwidth is calculated in various places using the same
multi-step formula. Doing this in one common place makes sure the same
formula will indeed be applied to all link bandwidth calculations.
It also makes it possible to apply link-setting-specific adjustments
that affect effective link bandwidth.
[how]
Replace all implementations of link bandwidth calculation with a call
to a function.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
When TM is enabled with 3dlut, we apply conversion to
dcip3 in gamut remap matrix, if source area less than
dcip3. If it is bigger, we remap to bt2020. The added
flags will be used to facilitate this logic.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently dcn2+ validation will unconditionally print a failure
reason before validation completes. This change categorizes the
failure reason as a warning log and only prints at the end of
validation resolving false positives.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
swath_bytes_horz_wc should be 256/64/64 for 2160p 32bpp surface
Signed-off-by: Bob Yang <Bob.Yang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn*_disable_plane() doesn't unlock the pipe anymore, making the extra
lock unnecessary.
In addition - during full plane updates - all necessary pipes should be
locked/unlocked together when modifying hubp to avoid tearing in
pipesplit setups.
[How]
Remove redundant locks, and add function to lock all pipes. If an
interdependent pipe update is required, lock down all pipes. Otherwise,
lock only the top pipe for the updated pipe tree.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A previous fix was done for DCN1 that needed to be ported to DCN2:
commit 60c677534e73 ("drm/amd/display: Disconnect mpcc when changing tg")
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why] we meet a bug when program dsc register even dsc mode is not
enabled. disable dsc config for now. we will re-visit this issue.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] dcn20 enable usb-c dp ALT mode in dmcu. There is bug
when enable abm feature which cause system crash. dal team
will debug this bug later.
[HOW] disable dcn abm feature for dcn20.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pstate allow/block is not being handled properly on DCN2
[how]
DML needs to be updated to calculate pstate support at both min and max
mpc combine rather than just min
clock manager needs to update current to new pstate support before
sending to pplib/smu
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding writeback_config enum to vba_vars_st, replacing old flag.
Initialize to dm_normal.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.
[How]
- Pull get_active_display_cnt out to clk_mgr.
- Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
DMUB is using DPREF CLK, but DMCU still use displayclk.
This is for updating DMCU wait_for_loop after display clock change.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Modern Standby may toggle display adapter state between D0
and D3 state unpredictably.
But events that cause transition to D0 are not always resulting
in a display light up scenario.
Modern eDP panels should be able to power on panel logic
quickly upon VDD going high. Based on spec, the T3 time
between VDD on and HPD high can be between 0 and 80 ms.
Doing any tricky sorts of optimization by powering on panel
VDD early during D0 transition on can negatively impact other
features due to unnecessary power drain and toggling when
final system state does not intend for the panel to be lit up.
We need OEMs to source higher end panels that have T3 time
close to 0 if they want quick S3/Modern Standby resume times.
[How]
Remove panel VDD power on in init_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
link-specific functions should reside in dc_link.c
[How]
Move them there.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Current calculation of bounding box will cause DML to increase voltage
state due to DPP or DISPCLK, this is unnecessary since from DML perspective
we can max DPP/DISP can be supported at DPM0. This is because
increasing voltage for DPP/DISP is done separately via actual minimum values
of DISP and DPP CLK
[how]
For each calculated state, DPP, DISP, PHY, and DSC clk should always be set to
maximum. FCLK, SOCCLK, and DCFCLK should be based of UCLK.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. DMCU is not running on some platform but driver still send ABM
command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable
[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.
[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
caller of pp_nv_set_pme_wa_enable pass incorrect pp_smu:
dc->res_pool->pp_smu. it should be dc->res_pool->pp_smu->nv_funcs.pp_smu.
with incorrect input, pp->dm = NULL. This causes system crash.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VTG has a parameter FP2, which is defined as:
if VSTARTUP is before VSYNC:
FP2 = number of lines in between VSTARTUP and VSYNC
else
FP2 = 0
Currently, FP2 is only programmed during "program_timing". However, the
position of VSTARTUP is affected by the prefetching requirements on all pipes,
so the position might change when we do memory request control on another pipe, so we need
to make sure that FP2 stays up-to-date whenever we adjust VSTARTUP.
[How]
- refactor VTG_CONTROL programming into a new function "set_vtg_params"
- call it after calling "program_global_sync"
- make sure it's called after because it relies on the cached dlg params
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
during bring up time, before window dc-ppplib interface
design, linux dc use raven dc-pplib interface.
now nvai10 dc-pplib-smu interface is changed and verified
under window, navi10 need its specific dc-pplib-smu
interface. todo: hook set_hard_min_uclk_by_freq,
get_maximum_sustainable_clocks
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program DCN2 VMID (Virtual Memory Support)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program DCN2 cursor (IPP)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 HUBP (Display to data fabric interface
pipe) and HUBBUB (DCN memory HUB interface)
HW Blocks:
+--------++------+
| HUBBUB || HUBP |
+--------++------+
|
v
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 DPP (Multiple pipe and plane combine)
HW Blocks:
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 MPC (Multiple pipe and plane combine)
HW Blocks:
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 OPP (Output Plane Processing)
HW Blocks:
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for handling of clocking relevant to the DCN2 block,
including programming of the DCCG (Display Controller Clock Generator)
block:
HW Blocks:
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN2, which entails our
stream and link encoders.
HW Blocks:
+--------+
| DIO |
+--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update DML (Display Mode Lib) to support DCN2
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program DCN2 IRQ handling
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding support to program GPIO HW block of DCN2
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding support to program DCN2 AUX and I2C HW.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN2.0 (Display Core Next) is the display block in Navi10.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We don't want to expose sensitive ASIC information before ASIC release.
[HOW]
Encode the soc_bounding_box in the gpu_info FW (for Linux) and read it
at driver load.
v2: fix warning when CONFIG_DRM_AMD_DC_DCN2_0 is not set (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add callback function get_clock_by_type_with_latency for navi10 asic
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit ebc8c6f18322ad54275997a888ca1731d74b711f.
There are still missing corner cases with cursor interaction and these
fast plane updates on Picasso and Raven2 leading to endless PSTATE
warnings for typical desktop usage depending on the userspace.
This change should be reverted until these issues have been resolved.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110949
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After clkmgr rework it gets initialized after resource pool.
The clkmgr is used in resource pool init for xgmi path.
That causes driver crash on Vega20 with xgmi due to NULL deref.
[How]
Move xgmi compensation code to dce121_clk_mgr_construct()
That also allows to make dce121_clock_patch_xgmi_ss_info()
internal static function.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Gj1MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGctkH/0At3+SQPY2JJSy8
i6+TDeytFx9OggeGLPHChRfehkAlvMb/kd34QHnuEvDqUuCAMU6HZQJFKoK9mvFI
sDJVayPGDSqpm+iv8qLpMBPShiCXYVnGZeVfOdv36jUswL0k6wHV1pz4avFkDeZa
1F4pmI6O2XRkNTYQawbUaFkAngWUCBG9ECLnHJnuIY6ohShBvjI4+E2JUaht+8gO
M2h2b9ieddWmjxV3LTKgsK1v+347RljxdZTWnJ62SCDSEVZvsgSA9W2wnebVhBkJ
drSmrFLxNiM+W45mkbUFmQixRSmjv++oRR096fxAnodBxMw0TDxE1RiMQWE6rVvG
N6MC6xA=
=+B0P
-----END PGP SIGNATURE-----
Merge v5.2-rc5 into drm-next
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The memory was set to zero already by a call of the function “kzalloc”.
Thus remove an extra call of the function “memset” for this purpose.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
"git diff" says:
\ No newline at end of file
after modifying the file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Add code to signal all dma-fences when freed with pending signals.
- Annotate reservation object access in CONFIG_DEBUG_MUTEXES
Core Changes:
- Assorted documentation fixes.
- Use irqsave/restore spinlock to add crc entry.
- Move code around to drm_client, for internal modeset clients.
- Make drm_crtc.h and drm_debugfs.h self-contained.
- Remove drm_fb_helper_connector.
- Add bootsplash to todo.
- Fix lock ordering in pan_display_legacy.
- Support pinning buffers to current location in gem-vram.
- Remove the now unused locking functions from gem-vram.
- Remove the now unused kmap-object argument from vram helpers.
- Stop checking return value of debugfs_create.
- Add atomic encoder enable/disable helpers.
- pass drm_atomic_state to atomic connector check.
- Add atomic support for bridge enable/disable.
- Add self refresh helpers to core.
Driver Changes:
- Add extra delay to make MTP SDM845 work.
- Small fixes to virtio, vkms, sii902x, sii9234, ast, mcde, analogix, rockchip.
- Add zpos and ?BGR8888 support to meson.
- More removals of drm_os_linux and drmP headers for amd, radeon, sti, r128, r128, savage, sis.
- Allow synopsis to unwedge the i2c hdmi bus.
- Add orientation quirks for GPD panels.
- Edid cleanups and fixing handling for edid < 1.2.
- Add runtime pm to stm.
- Handle s/r in dw-hdmi.
- Add hooks for power on/off to dsi for stm.
- Remove virtio dirty tracking code, done in drm core.
- Rework BO handling in ast and mgag200.
-----BEGIN PGP SIGNATURE-----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=4uQX
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add code to signal all dma-fences when freed with pending signals.
- Annotate reservation object access in CONFIG_DEBUG_MUTEXES
Core Changes:
- Assorted documentation fixes.
- Use irqsave/restore spinlock to add crc entry.
- Move code around to drm_client, for internal modeset clients.
- Make drm_crtc.h and drm_debugfs.h self-contained.
- Remove drm_fb_helper_connector.
- Add bootsplash to todo.
- Fix lock ordering in pan_display_legacy.
- Support pinning buffers to current location in gem-vram.
- Remove the now unused locking functions from gem-vram.
- Remove the now unused kmap-object argument from vram helpers.
- Stop checking return value of debugfs_create.
- Add atomic encoder enable/disable helpers.
- pass drm_atomic_state to atomic connector check.
- Add atomic support for bridge enable/disable.
- Add self refresh helpers to core.
Driver Changes:
- Add extra delay to make MTP SDM845 work.
- Small fixes to virtio, vkms, sii902x, sii9234, ast, mcde, analogix, rockchip.
- Add zpos and ?BGR8888 support to meson.
- More removals of drm_os_linux and drmP headers for amd, radeon, sti, r128, r128, savage, sis.
- Allow synopsis to unwedge the i2c hdmi bus.
- Add orientation quirks for GPD panels.
- Edid cleanups and fixing handling for edid < 1.2.
- Add runtime pm to stm.
- Handle s/r in dw-hdmi.
- Add hooks for power on/off to dsi for stm.
- Remove virtio dirty tracking code, done in drm core.
- Rework BO handling in ast and mgag200.
Tiny conflict in drivers/gpu/drm/amd/display/dc/clk_mgr/clk_mgr.c,
needed #include <linux/slab.h> to make it compile.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0e01de30-9797-853c-732f-4a5bd6e61445@linux.intel.com
I missed amdgpu in my connnector_helper_funcs->atomic_check conversion,
which is understandably causing compilation failures.
Fixes: 6f3b62781b ("drm: Convert connector_helper_funcs->atomic_check to accept drm_atomic_state")
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> [for rcar lvds]
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <karolherbst@gmail.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: dri-devel@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190614002713.141340-1-sean@poorly.run
this patch fixes below compilation error
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c: In
function ‘dcn10_apply_ctx_for_surface’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2378:3:
error: implicit declaration of function ‘udelay’
[-Werror=implicit-function-declaration]
udelay(underflow_check_delay_us);
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: hersen wu <hersenxs.wu@amd.com>
Cc: "Leo (Hanghong) Ma" <hanghong.ma@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Found issue in EDID Emulation where if we connect a display using
a passive HDMI-DP dongle, disconnect it and then try to emulate
a display using DP, we could not see 4K modes. This was because
on a disconnect, dongle_max_pix_clk was still set so when we
emulate using DP, in dc_link_validate_mode_timing(), it would
think we were still using a dongle and limit the modes we support.
[How]
In dc_link_detect(), set dongle_max_pix_clk to 0 when we detect
a hotplug out ( if new_connection_type = dc_connection_none ).
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
refactor a code so we will call clk_mgr's enable_pme_wa function so we
can use pme_wa for future asics. This way we don't need to worry about
different ASIC since clk_mgr already have that information
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
The spec does not allow POST_LT_ADJ_GRANTED to be set when TPS4 is used.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We incorrectly began powering down the display at boot/resume whenever
fast boot was not possible. This should not be done in the case where there
exists a stream for the eDP since this implies that we want to turn it on.
[How]
Add check for eDP stream to decide whether to power off edp.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
By the time output csc matrix is being programmed, stream connection to
OPP has been established, but this information has not been relayed back
to HUBP.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Our existing logic in deciding whether to use RAM or ROM
depends on whether we are dealing with an identity gamma ramp.
[How]
In addition to the is_identity flag
a new is_logical_identity flag has been
added. The is_identity flag now denotes
whether the OS gamma is an RGB256 identity
and the new logical identity will inidicate
that the given gamma ramp regardless of its
type is identity.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging underflow issues it can be useful to have asserts when the
underflow initially occurs.
[How]
Read the underflow status registers after actions that have a high risk
of causing underflow and assert that no underflow occurred. If underflow
occurred, clear the bit.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently vmid is decided internally inside dc. This makes it
difficult to use vmid use with external components.
This change moves vmid logic outside dc and allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBios sometimes reports incorrect object type as encoder instead of
connector
[How]
Change error message to debug message
Signed-off-by: Jordan Lazare <Jordan.Lazare@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are no longer needed, Also added RESERVED bits.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using this logic breaks driver unload, this is a temporary fix
a followup patch will properly fix this
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD not going to be high if Panel VDD is off
And all AUX transaction will fail :(
[How]
1. Power on VDD before attempting detection if it isn't already on
2. Improve the robustness by having a retry mechanism on the
first DPCD read after VDD on. If a particular board always holds
HPD high incorrectly, the AUX access may fail, so we can retry
in those scenarios. This change would only improve logic
since it prevents AUX failure leading to bad resolution on internal
panel.
3. We should never need to re-detect internal panel, so logic
is re-arranged a bit to skip earlier.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for the upcoming DRM plane color management properties
we need to correct a lot of wrong behavior and assumptions made for
CRTC color management.
The documentation added by this commit in amdgpu_dm_color explains
how the HW color pipeline works and its limitations with the DRM
interface.
The current implementation does the following wrong:
- Implicit sRGB DGM when no CRTC DGM is set
- Implicit sRGB RGM when no CRTC RGM is set
- No way to specify a non-linear DGM matrix that produces correct output
- No way to specify a correct RGM when a linear DGM is used
We had workarounds for passing kms_color tests but not all of the
behavior we had wrong was covered by these tests (especially when
it comes to non-linear DGM). Testing both DGM and RGM at the same time
isn't something kms_color tests well either.
[How]
The specifics for how color management works in AMDGPU and the new
behavior can be found by reading the documentation added to
amdgpu_dm_color.c from this patch.
All of the incorrect cases from the old implementation have been
addressed for the atomic interface, but there still a few TODOs for
the legacy one.
Note: this does cause regressions for kms_color@pipe-a-ctm-* over HDMI.
The result looks correct from visual inspection but the CRC no longer
matches. For reference, the test was previously doing the following:
linear degamma -> CTM -> sRGB regamma -> RGB to YUV (709) -> ...
Now the test is doing:
linear degamma -> CTM -> linear regamma -> RGB to YUV (709) -> ...
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This is meant to make it clearer that 0xf is not a valid OPP ID, and
that code making use of OPP IDs should not accept this value.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Add i2c_hw_Status check to make sure when HW i2c is in use.
2. Don't reset HW engine in is_hw_busy() and instead do this in
process_transaction() because SW i2c does not check if hw i2c is in use
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to assert just return
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Almost every function in DC that works with stream state expects that
the current state on the stream is the one that it should be writing
out. These functions are typically triggered by specifying a particular
stream update - but the actual contents of the stream update itself
are ignored, leaving it to the DM to actually update the stream state
itself.
The problem with doing this in DM is a matter of timing. On Linux
most of this is incorrectly done in atomic check, when we actually want
it to be done during atomic commit tail while access to DC is locked.
To give an example, a commit requesting to modify color management
state for DM could come in, be rejected, but still have modified
the actual system state for the stream since it's shared memory. The
next time color management gets programmed it'll use the rejected
color management info - which might not even still be around if it's
a custom transfer function.
So a reasonable place to perform this is within DC itself and this is
the model that's currently in use for surface updates. DC can even
compare the current system state to the incoming surface update to
determine update level, something that can't currnetly be done with the
framework for stream updates.
[How]
Duplicate the framework used for surface updates for stream updates
as well. Copy all the updates after checking the update type.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some panels return a link rate of 0 (unknown) in DPCD 0. In this case,
an appropriate mode cannot be set, and certain panels will show
corruption as they are forced to use a mode they do not support.
[HOW]
Read DPCD 10 in the case where supported link rate from DPCD 0 is
unknown, and pass that value on to the reported link rate.
This re-introduces behaviour present in previous versions that appears
to have been accidentally removed.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tao.Huang <Tao.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The module parameter to specify the default ABM level is now defined,
so hook it up in DM.
[How]
On connector reset specify the default level. DC will program this as
part of the modeset since it gets passed onto the stream in
dm_update_crtc_state.
It's only set for eDP connectors, but it doesn't matter if this is
specified for connectors or hardware that doesn't support ABM.
It's DC's responsibility to check that ABM can be set or adjusted, and
DC does check that the DMCU firmware is running and if there's backlight
control available.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever the a modeset is allowed (but not neccessarily required) we
currently recreate all the planes in the state. Most IGT tests and
legacy IOCTLs create atomic commits with this flag set, so the pipes
are often unnecessarily reprogrammed.
Poor performance and stuttering can occur when many of these commits
are frequently issued.
This flag was needed when the appropriate conditions for checking
whether the planes needed a reset were not in place, but
should_reset_plane should cover everything needed now.
[How]
Drop the check for state->allow_modeset in should_reset_plane.
All planes on a CRTC should reset in the following conditions:
- The CRTC needs a modeset
- The CRTC degamma changes
- Planes are added or removed to the CRTC
These conditions are all covered in should_reset_plane.
We still can't drop the format change check in should_reset_plane since
fill_dc_plane_info_and_addr isn't called when validating the state, so
we can't tell if a FULL update is needed or not.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The old logic for checking which output depth to use relied on using
the current connector state rather than the new proposed state. This
was a problem when performing atomic commits since we weren't verifying
it against the incoming max_requested_bpc.
But switching this to only use the new state and not the current state
breaks filtering modes - it'll always assume that the maximum bpc
supported by the display is in use, which will cause certain modes
like 1440p@144Hz to be filtered even when using 8bpc.
[How]
Still use the connector->state if we aren't passed an explicit state.
This will respect the max_bpc the user currently has when filtering
modes.
Also remember to reset the default max_requested_bpc to 8 whenever
connector reset is called to retain old behavior when using the new
property.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110845
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unlike our regular connectors, MST connectors don't start off with
an initial connector state. This causes a NULL pointer dereference to
occur when attaching the bpc property since it tries to modify the
connector state.
We need an initial connector state on the connector to avoid the crash.
[How]
Use our reset helper to allocate an initial state and reset the values
to their defaults. We were already doing this before, just not for
MST connectors.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This will be useful for verifying whether we enter the correct output
color depth from IGT.
[How]
Locks the connector and associated CRTC if available and outputs
the current and maximum output bpc values.
Example:
cat /sys/kernel/debug/dri/0/DP-1/output_bpc
Current: 8
Maximum: 10
v2: Drop unneeded connector status check
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN_VERSION_1_01 is no longer handled in the dal_hw_translate_init
switch since it was inadvertently dropped in the patch that removed the
unnecessary DCN1_01 guards.
This caused numerous regressions on DCN1_01 when loading the driver.
[How]
Add it back.
Fixes: 97df424fe7 ("drm/amd/display: Drop DCN1_01 guards")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching from vt to desktop with EDID emulation we can receive
an atomic commit such that we have a crtc where mode_changed = true.
During the dm_update_crtc_state disable pass we remove the stream from
the context and free it on the dm_new_crtc_state.
During the enable pass we compare the new provisional stream to the
dm_old_crtc_state->stream and determine that the stream is unchanged
and no scaling has been changed.
Following this, new_crtc_state->mode_changed is then set to false.
The connectors haven't changed and the CRTC active state hasn't changed
so drm_atomic_crtc_needs_modeset returns false, so we jump to
skip_modeset and we hit:
BUG_ON(dm_new_crtc_state->stream == NULL);
...since the old stream is gone from the context and the new stream is
also still NULL.
[How]
Ensure that we still a stream to reuse before checking if we can reuse
the old stream without a full modeset.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop all uses of drmP.h in drm/amd/display/.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-9-sam@ravnborg.org
Drop use of the deprecated drmP.h header file from
all amd header files.
This makes it a more smooth process to get rid of drmP.h
in the .c files.
Added include files and forwards as appropriate.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-7-sam@ravnborg.org
Drop use of the deprecated drmP.h header from atom.h
Fix fallout in various files.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-6-sam@ravnborg.org
Delete the unused drmP.h from amdgpu.h.
Fix fallout in various files.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-5-sam@ravnborg.org
Drop use of the deprecated drmP.h from display/dc/os_types.h
Fix all fallout after this change.
Most of the fixes was adding a missing include of vmalloc.h.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-4-sam@ravnborg.org
Fix so no files in drm/amd/ depends on the
deprecated drm_os_linux.h header file.
It was done manually:
- remove drm_os_linux.h from drmP.h
- fix all build errros
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-3-sam@ravnborg.org
amdgpu:
- Revert timeline support until KHR is ready
- Various driver reload fixes
- Refactor clock handling in DC
- Aux fixes for DC
- Bandwidth calculation updates for DC
- Fix documentation due to file rename
- RAS fix
- Fix race in late_init
ttm:
- Allow for better forward progress when there is heavy memory contention
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190606032537.6939-1-alexander.deucher@amd.com
These got added back by subsequent merges accidently.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
-----BEGIN PGP SIGNATURE-----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=GrAP
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6c43ffa9-11ff-5354-d772-c20fd4d1e3d9@linux.intel.com
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Calling drm_atomic_set_fb_for_plane() (which gets a reference of the new
fb and put the old fb) is not required, as it's taken care by
drm_mode_cursor_universal() when calling drm_atomic_helper_update_plane().
Cc: <stable@vger.kernel.org> # v4.20+
Fixes: 674e78acae ("drm/amd/display: Add fast path for cursor plane updates")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-3-helen.koike@collabora.com
[Why]
We can issue HDR static metadata as part of stream updates for
non-modesets as long as we force a modeset when entering or exiting HDR.
This avoids unnecessary blanking for simple metadata updates.
[How]
When changing scaling and abm for the stream also check if HDR has
changed and send the stream update. This will only happen in non-modeset
cases.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-3-nicholas.kazlauskas@amd.com
[Why]
For userspace to send static HDR metadata to the display we need to
attach the property on the connector and send it to DC.
[How]
The property is attached to HDMI and DP connectors. Since the metadata
isn't actually available when creating the connector this isn't a
property we can dynamically support based on the extension block
being available or not.
When the HDR metadata is changed a modeset will be forced for now.
We need to switch from 8bpc to 10bpc in most cases anyway, and we want
to fully exit HDR mode when userspace gives us a NULL metadata, so this
isn't completely unnecessary.
The requirement can later be reduced to just entering and exiting HDR
or switching max bpc.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-2-nicholas.kazlauskas@amd.com
add ticket for display bo, so that it can preempt busy bo.
v2: fix stupid rebase error
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Issue:
Will have follow error when reload driver:
[ 3986.567739] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:07.0/drm_dp_aux_dev'
[ 3986.567743] CPU: 6 PID: 1767 Comm: modprobe Tainted: G OE 5.0.0-rc1-custom #1
[ 3986.567745] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 3986.567746] Call Trace:
......
[ 3986.567808] drm_dp_aux_register_devnode+0xdc/0x140 [drm_kms_helper]
......
[ 3986.569081] kobject_add_internal failed for drm_dp_aux_dev with -EEXIST, don't try to register things with the same name in the same directory.
Reproduce sequences:
1.modprobe amdgpu
2.modprobe -r amdgpu
3.modprobe amdgpu
Root cause:
When unload driver, it doesn't unregister aux.
v2: Don't use has_aux
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We only want to manual trigger end-of-frame when the bottom-most
pipe is flipped to prevent overlays from ending the frame too early.
[How]
Check that the manual trigger is only firing on bottom plane.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There's some unnecessary mem allocation for CS_TFM_ID. What's worse, it
depends on LUT size and since it's 4K for CS_TFM_1D, it is 16x bigger
than in regular case when it's actually needed. This leads to some
crashes in stress conditions.
[How]
Skip ramp combining designed for RGB256 and DXGI gamma with CS_TFM_1D.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For commits with allow_modeset=false and CRTC degamma changes the planes
aren't reset. This results in incorrect rendering.
[How]
Reset the planes when color management has changed on the CRTC.
Technically this will include regamma changes as well, but it doesn't
really after legacy userspace since those commit with
allow_modeset=true.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some backlight tests fail due to backlight settling
taking too long. This happens because the step
size used to change backlight levels is too small.
[How]
1. Change the size of the backlight gain step size
2. Change how DMCU firmware gets the step size value
so that it is passed in by driver during DMCU initn
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some displays take some time to power up AUX CH once they are
put into D3 state via write to DPCD 600h=2.
Interestingly enough, some display may simply NACK, but some might
also ACK with a bunch of 0s, which can cause issues with receiver
cap retrieval. Note that not all DPCD address return 0s, but in
particular it has been observed on some higher DPCD address such
as DPCD 2200h, etc.
[How]
Based on spec, receiver will monitor differential signal while in D3 and
AUX CH is in low power mode. When detected, it may allow up to
1 ms to power up AUX CH and reply.
If we read Sink power state D3, we should add 1 ms delay to satisfy
this spec requirement.
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description] This is cause by failing to read link caps from driver.
Signed-off-by: Daniel He <daniel.he@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding writeback_config enum to vba_vars_st, replacing old flag.
Initialize to dm_normal.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.
[How]
* Pull get_active_display_cnt out to clk_mgr.
* Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Value read from SMU is 16 bits, not 32.
[How]
Fix type, and add wm_type enum in preparation for future interfaces.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Modern Standby may toggle display adapter state between D0
and D3 state unpredictably.
But events that cause transition to D0 are not always resulting
in a display light up scenario.
Modern eDP panels should be able to power on panel logic
quickly upon VDD going high. Based on spec, the T3 time
between VDD on and HPD high can be between 0 and 80 ms.
Doing any tricky sorts of optimization by powering on panel
VDD early during D0 transition on can negatively impact other
features due to unnecessary power drain and toggling when
final system state does not intend for the panel to be lit up.
We need OEMs to source higher end panels that have T3 time
close to 0 if they want quick S3/Modern Standby resume times.
[How]
Remove panel VDD power on in init_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
during It's possible to call dcn_validate_bandwidth with no plane.
In that case, as we are only intersted in if output timing is supported or not,
even if we cannot support native resolution, we still want to support lower
resolution if it is valid
[how]
if there exist no surface, make viewport/rec_out size at max 1080p. It is
already known that 1080p x 6(max # of pipes) is supported, so if we fail
validation, it is because of the stream
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
by adding fast_validate flag, we are skipping some portion of
dcn_validate_bandwidth code that is not necessary for mode validation.
However we have a bug where it does not calculate
v->total_data_read_bandwidth, which is one of the factors determines the
result of the validation, and therefore report false positive during
mode validation.
[how]
add calculation of v->total_data_read_bandwidth outside of the region
that is guarded by fast_validate flag
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
link-specific functions should reside in dc_link.c
[How]
Move them there.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add min_dcfclk_mhz to bounding box overrides.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Better organization
[How]
Move clk_mgr files under dc/clk_mgr
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. DMCU is not running on some platform but driver still send ABM
command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable
[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.
[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GSL is a form of locking that can be used to synchronize pipes in a
pipe-split configurations when async flip is used. Add the registers
here.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously there were 2 consecutive calls being made to disable
audio stream. The first one disabled the audio stream, and the second
one went through and also tried to disable the audio stream causing
BACO entry issues due to the ASIC appearing busy.
[How]
1. Add a status field to the audio struct which stores enabled/disabled
info
2. In the calls to enable/disable audio stream check if we're already
in the desired state before executing the function
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
stream id should uniquely identify an instance of stream.
the copy constructor should be treated as a new
stream instance.
[how]
assign a new stream id in this copy constructor.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This macro is specificly used by RV1. Move it to the appropriate
location.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add vtable entries for de-alpha and bias color management interfaces.
Move piece-wise transfer function registers to a helper list for future
reuse.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can’t use hardcoded SRGB ROM for output TF if we have GAMMA_CS_TFM_1D
(unless we know 1D LUT is identity), so we never want to return here early.
We apply the LUT part of ColorTransform3x4 only in apply_lut_1d() which is
called near the end of that function.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
First step of refactoring clk mgr to better handle different
ways of handling clock operations. Clock operation policies are
soc specific and not just DCN vesion specific. It is not a hw resource,
should not be in the resource pool.
[How]
Change clock manager creation to be based on HW internal ID, rename
clock manager members to be more clear. Move clock manager out of
resource.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New stuff for 5.3:
- Add new thermal sensors for vega asics
- Various RAS fixes
- Add sysfs interface for memory interface utilization
- Use HMM rather than mmu notifier for user pages
- Expose xgmi topology via kfd
- SR-IOV fixes
- Fixes for manual driver reload
- Add unique identifier for vega asics
- Clean up user fence handling with UVD/VCE/VCN blocks
- Convert DC to use core bpc attribute rather than a custom one
- Add GWS support for KFD
- Vega powerplay improvements
- Add CRC support for DCE 12
- SR-IOV support for new security policy
- Various cleanups
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190529220944.14464-1-alexander.deucher@amd.com
dc_destroy should be called amdgpu_cgs_destroy_device,
as it will use cgs context to read or write registers.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are monitors which can have more than one preferred mode
set. There are chances in these monitors that if common modes are
added in function amdgpu_dm_connector_add_common_modes(), these
common modes can be calculated with different preferred mode than
the one used in function decide_crtc_timing_for_drm_display_mode().
The preferred mode can be different because after common modes
are added, the mode list is sorted and this changes the order of
preferred modes in the list. The first mode in the list with
preferred flag set is selected as preferred mode. Due to this the
preferred mode selected varies.
If same preferred mode is not selected in common mode calculation
and crtc timing, then during mode set instead of setting preferred
timing, common mode timing will be applied which can cause "out of
range" message in the monitor with monitor blanking out.
[How]
Sort the modes before adding common modes. The same sorting function
is called during common mode addition and deciding crtc timing.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The current state on the connector is queried when getting the max bpc
rather than the new state. This means that a new max bpc value can only
currently take effect on the commit *after* it changes.
The new state should be passed in instead.
[How]
Pass down the dm_state as drm state to where we do color depth lookup.
The passed in state can still be NULL when called from
amdgpu_dm_connector_mode_valid, so make sure that we have reasonable
defaults in place. That should probably be addressed at some point.
This change now (correctly) causes a modeset to occur when changing the
max bpc for a connector.
v2: Drop extra TODO.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The custom "max bpc" property was added to limit color depth while the
DRM one was still being merged. It's been a few kernel versions since
then and this TODO was still sticking around.
[How]
Attach the DRM max bpc property to the connector and drop all of our
custom property management. Set the max bpc to 8 by default since
DRM defaults to the max in the range which would be 16 in this case.
No behavioral changes are intended with this patch, it should just be
a refactor.
v2: Don't force 8bpc when no state is given
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When disable driver, OS will set backlight optimization
then do stop device. But this flag will cause driver to
enable ABM when driver disabled.
[How]
Send ABM disable command before destroy ABM construct
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
move the update of otg instance outside of hw programming logic,
since this is sw state, it should always be updated and should
never be optimized away.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The bit for flip addr is being set causing the determination for
FAST vs MEDIUM to always return MEDIUM when plane info is provided
as a surface update. This causes extreme stuttering for the typical
atomic update path on Linux.
[How]
Don't use update_flags->raw for determining FAST vs MEDIUM. It's too
fragile to changes like this.
Explicitly specify the update type per update flag instead. It's not
as clever as checking the bits itself but at least it's correct.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eryk Brol <Eryk.Brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DPRX should send the VCP extended colorimetry packet if the
sink supports DPCD rev1.4 and reports the extended colorimetry
bit.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN code should make as few references to DCE as possible
[HOW]
Copy DCE110 implementation of find_first_free_match_stream_enc_for_link
into DCN10
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
From DCE110 onward, we have the ability to assign DIG BE and FE
separately for any display connector type; before, we could only do this
for DP.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. No real HPD plug in/out but HPD happens,
the driver notifies OS connection changed.
2. No display in target.
When HPD goes low to high,
the driver should regard as HPD and enter setmode flow.
[How]
In this case, even stream didn't change but still retrain.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VTG has a parameter FP2, which is defined as:
if VSTARTUP is before VSYNC:
FP2 = number of lines in between VSTARTUP and VSYNC
else
FP2 = 0
Currently, FP2 is only programmed during "program_timing". However, the
position of VSTARTUP is affected by the prefetching requirements on all pipes,
so the position might change when we do memory request control on another pipe, so we need
to make sure that FP2 stays up-to-date whenever we adjust VSTARTUP.
[How]
- refactor VTG_CONTROL programming into a new function "set_vtg_params"
- call it after calling "program_global_sync"
- make sure it's called after because it relies on the cached dlg params
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Reuse existent code path and in order to do that apply de gamma
in 1D blender LUT and re use MPC OGAM.
Follow up is required.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DPMS state of a display should not impact whether we want to enable fast boot.
Currently fast boot is not enabled when resuming from S4 because of this.
[How]
Remove check for DPMS state when determining if fast boot
can be applied.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many IGT tests require CRC capture in order to confirm that the output
is visually correct.
These skip on dce120 because configure_crc and get_crc aren't set.
[How]
Hook up is_tg_enabled, configure_crc and get_crc functions on dce120's
timing generator.
The logic should be the same as DCE and DCN with some minor register
naming differences.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add these parameters for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These were only needed for bringup. They're not needed anymore.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some early Raven boards had a bad SBIOS that doesn't play nicely with
the DMCU FW. We thought the issues were fixed by ignoring errors on DMCU
load but that doesn't seem to be the case. We've still seen reports of
users unable to boot their systems at all.
[HOW]
Disable DMCU load on Raven 1. Only load it for Raven 2 and Picasso.
v2: Fix ifdef (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We only want to load DMCU FW on Picasso and Raven 2, not on Raven 1.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Fix the following sparse warnings:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:483:21: warning: symbol 'dce120_clock_source_create' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:506:6: warning: symbol 'dce120_clock_source_destroy' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:513:6: warning: symbol 'dce120_hw_sequencer_create' was not declared. Should it be static?
Fixes: b8fdfcc6a9 ("drm/amd/display: Add DCE12 core support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To send sdp message immediately from a single slot.
[How]
Modify the generic SDP message interface, and use GSP4 to send immediate
sdp message.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In fill_plane_buffer_attributes() we calculate chroma/luma
assuming that the surface_pixel_format is always valid.
If it's not the case, there's a risk of divide by zero error.
[How]
Check if format valid before calculating pixel format attributes
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Upon closer inspection, our previous implementation is missing
code for programming de-spread and DP DTO. Porting this logic
into driver is rather involved, as there are a lot of table
look ups. So for now move back to calling vbios cmd table
[How]
Go back to calling vbios cmd table for set dp_refclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This function needs to re-calculate the scaling on the pipe
that loses it's half.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are internal otg params and should be handled as such.
Thich change passes the params as function arguments.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It makes no logical sense being there
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
This is for HDMI 6Ghz mode before we load the driver, because VBIOS
not support HDMI (6Ghz mode)
Reset to redriver/retimer setting for the setting for below 340Mhz.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Part of HDMI 2.1 requires AVI InfoFrame version update
from current V2 to V4 for new colorimetry.
[How]
Define V4 AVI InfoFrame ACE0-ACE3 bit.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When x or y is negative we set the x and y values to 0 and compensate
with a positive cursor hotspot in DM since DC expects positive cursor
values.
When x or y is less than or equal to the maximum cursor width or height
the cursor hotspot is clamped so the hotspot doesn't exceed the
cursor size:
if (x < 0) {
xorigin = min(-x, amdgpu_crtc->max_cursor_width - 1);
x = 0;
}
if (y < 0) {
yorigin = min(-y, amdgpu_crtc->max_cursor_height - 1);
y = 0;
}
This incorrectly forces the cursor to be at least 1 pixel on the screen
in either direction when x or y is sufficiently negative.
[How]
Just disable the cursor when it goes far enough off the screen in one
of these directions.
This fixes kms_cursor_crc@cursor-256x256-offscreen.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
An assertion is thrown when using SURFACE_PIXEL_FORMAT_GRPH_RGB565
formats on DCE since the prescale_params->scale wasn't being filled.
Found by a dmesg-fail when running the
igt@kms_plane@pixel-format-pipe-a-planes test on Baffin.
[How]
Fill in the scale parameter.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Part of HDMI 2.1 requires AVI InfoFrame version update
from current V2 to V3 for new VICs, and V4 for
new colorimetry.
[How]
Implement V3 and V4 AVI InfoFrame.
If (C1, C0)=(1, 1) and (EC2, EC1, EC0)=(1, 1, 1),
the Source shall use 20 AVI InfoFrame Version 4.
If VIC >= 128, the Source shall use AVI InfoFrame Version 3
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Emulating passive dongle on USB-C port causes issue on some asics.
[How]
Check for DP_IS_USB_C flag in bios parser and propagate it to
encoder features flags. If DP_IS_USB_C flag is set and it is trying to
emulate passive dongle, then return fail.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
This is for DC_I2c arbitration use between HW use/SW use and DMCU use.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On some configurations, eDP from GPU is muxed with another GPU. DC does
not know state of mux, but DM has this knowledge. This flag allows DC to ignore
creating EDP link when DM informs DC that EDP mux is not connected.
[how]
Add flag to dc, populate flag in DM
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To simply logic for setting DCN specific clocks, we will send
SMU message directly through the VBIOS message box.
[How]
Add new structure in pp_smu to hold functions to set clocks
through vbios message box
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a scenario that causes eDP to become blank if
there are multiple displays connected, and the external
display is set as the primary display such that the first
flip comes to the external display.
In this scenario, we call our optimize function before
the eDP even has a chance to flip.
[How]
There is a check that prevents bandwidth optimize from
occurring before first flip is complete on the seamless boot
display.
But actually it assumed the seamless boot display is the
first one to flip. But in this scenario it is not.
Modify the check to ensure the steam with the seamless
boot flag set is the one that has completed the first flip.
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----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=4Wu/
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2019-05-24-1' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Nothing too unusual here for rc2. Except the amdgpu DMCU firmware
loading fix caused build breakage with a different set of Kconfig
options. I've just reverted it for now until the AMD folks can rewrite
it to avoid that problem.
i915:
- boosting fix
- bump ready task fixes
- GVT - reset fix, error return, TRTT handling fix
amdgpu:
- DMCU firmware loading fix
- Polaris 10 pci id for kfd
- picasso screen corruption fix
- SR-IOV fixes
- vega driver reload fixes
- SMU locking fix
- compute profile fix for kfd
vmwgfx:
- integer overflow fixes
- dma sg fix
sun4i:
- HDMI phy fixes
gma500:
- LVDS detection fix
panfrost:
- devfreq selection fix"
* tag 'drm-fixes-2019-05-24-1' of git://anongit.freedesktop.org/drm/drm: (32 commits)
Revert "drm/amd/display: Don't load DMCU for Raven 1"
drm/panfrost: Select devfreq
drm/gma500/cdv: Check vbt config bits when detecting lvds panels
drm/vmwgfx: integer underflow in vmw_cmd_dx_set_shader() leading to an invalid read
drm/vmwgfx: NULL pointer dereference from vmw_cmd_dx_view_define()
drm/vmwgfx: Use the dma scatter-gather iterator to get dma addresses
drm/vmwgfx: Fix compat mode shader operation
drm/vmwgfx: Fix user space handle equal to zero
drm/vmwgfx: Don't send drm sysfs hotplug events on initial master set
drm/i915/gvt: Fix an error code in ppgtt_populate_spt_by_guest_entry()
drm/i915/gvt: do not let TRTTE and 0x4dfc write passthrough to hardware
drm/i915/gvt: add 0x4dfc to gen9 save-restore list
drm/i915/gvt: Tiled Resources mmios are in-context mmios for gen9+
drm/i915/gvt: use cmd to restore in-context mmios to hw for gen9 platform
drm/i915/gvt: emit init breadcrumb for gvt request
drm/amdkfd: Fix compute profile switching
drm/amdgpu: skip fw pri bo alloc for SRIOV
drm/amd/powerplay: fix locking in smu_feature_set_supported()
drm/amdgpu/gmc9: set vram_width properly for SR-IOV
drm/amdgpu/soc15: skip reset on init
...
[WHY]
Some early Raven boards had a bad SBIOS that doesn't play nicely with
the DMCU FW. We thought the issues were fixed by ignoring errors on DMCU
load but that doesn't seem to be the case. We've still seen reports of
users unable to boot their systems at all.
[HOW]
Disable DMCU load on Raven 1. Only load it for Raven 2 and Picasso.
v2: Fix ifdef (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This reverts commit 55143dc23c.
This causes build breakags with some Kconfigs so revert for now.
Fixes: 55143dc23c ("drm/amd/display: Don't load DMCU for Raven 1")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
Some early Raven boards had a bad SBIOS that doesn't play nicely with
the DMCU FW. We thought the issues were fixed by ignoring errors on DMCU
load but that doesn't seem to be the case. We've still seen reports of
users unable to boot their systems at all.
[HOW]
Disable DMCU load on Raven 1. Only load it for Raven 2 and Picasso.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[WHY]
We only want to load DMCU FW on Picasso and Raven 2, not on Raven 1.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJc3MkNAAoJEAx081l5xIa+DpkP/2VhwTcnyumBi/cxG9/D/vRN
W0tZDaiR3jvdz5J0lbg03fJnzgbBIFREjS9/W3PmVbsAvzMfUTok9trlw1rht82a
NLbfK/Ge8e+OqmSRJ5kqMblixoWyqmM03/3/ms/nSfd86qywYpLy3ldZHK+WKdJq
BV3topSeuP6dUj35v4L7y69DZ0Q6ignOe8udjkJgUyq9HCU7PxXxiV1K/9wUeFq1
EL736LTnvm7djzseS0kOSIB2oguRnP+6czYkVvMwP2bxuDayklOjAL6s489pvX6e
36FkFXFksj7vvi3s9JfKQ6gmlE4GbWvFevI0cXzB+G9mWr53nrV+iinRvx9neA3C
YG263vD14Brm6Nfr4PCMAI7PgNLas9y0cpzc6LwjpJdWTmPiY/UhHmYbk81ZGEC5
s6Du8vt2PHvkbsyWdNglpPztZzGTKihCIoAtoDzH0TQTLVvoUsr8CKEk/w7wUtuQ
NZSoDnlxlRVVRx07H8/aSYzwDjY9R0J3zCPRCrkDhoPy2tGFJd4xv/d2c1uVV19v
VVqUZLHNhXdSJiu0RNRmyJktgQgnMsONRqaY6qsJq9O8sQrMVU5V+BRk9iBm/m21
xSw1nXJZsPYIqvxgF6+mmr98bIktu47htguV+Zp4rCUzAfO0YxBO5++vqBrLRPax
T97d8gQopoX5nnBI4pzN
=EfK4
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-16' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"A bunch of fixes for the merge window closure, doesn't seem to be
anything too major or serious in there.
It does add TU117 turing modesetting to nouveau but it's just an
enable for preexisting code.
amdgpu:
- gpu reset at load crash fix
- ATPX hotplug fix for when dGPU is off
- SR-IOV fixes
radeon:
- r5xx pll fixes
i915:
- GVT (MCHBAR, buffer alignment, misc warnings fixes)
- Fixes for newly enabled semaphore code
- Geminilake disable framebuffer compression
- HSW edp fast modeset fix
- IRQ vs RCU race fix
nouveau:
- Turing modesetting fixes
- TU117 support
msm:
- SDM845 bringup fixes
panfrost:
- static checker fixes
pl111:
- spinlock init fix.
bridge:
- refresh rate register fix for adv7511"
* tag 'drm-next-2019-05-16' of git://anongit.freedesktop.org/drm/drm: (36 commits)
drm/msm: Upgrade gxpd checks to IS_ERR_OR_NULL
drm/msm/dpu: Remove duplicate header
drm/pl111: Initialize clock spinlock early
drm/msm: correct attempted NULL pointer dereference in debugfs
drm/msm: remove resv fields from msm_gem_object struct
drm/nouveau: fix duplication of nv50_head_atom struct
drm/nouveau/disp/dp: respect sink limits when selecting failsafe link configuration
drm/nouveau/core: initial support for boards with TU117 chipset
drm/nouveau/core: allow detected chipset to be overridden
drm/nouveau/kms/gf119-gp10x: push HeadSetControlOutputResource() mthd when encoders change
drm/nouveau/kms/nv50-: fix bug preventing non-vsync'd page flips
drm/nouveau/kms/gv100-: fix spurious window immediate interlocks
drm/bridge: adv7511: Fix low refresh rate selection
drm/panfrost: Add missing _fini() calls in panfrost_device_fini()
drm/panfrost: Only put sync_out if non-NULL
drm/i915: Seal races between async GPU cancellation, retirement and signaling
drm/i915: Fix fastset vs. pfit on/off on HSW EDP transcoder
drm/i915/fbc: disable framebuffer compression on GeminiLake
drm/amdgpu/psp: move psp version specific function pointers to early_init
drm/radeon: prefer lower reference dividers
...
-----BEGIN PGP SIGNATURE-----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=YFiQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This has two exciting community drivers for ARM Mali accelerators.
Since ARM has never been open source friendly on the GPU side of the
house, the community has had to create open source drivers for the
Mali GPUs. Lima covers the older t4xx and panfrost the newer 6xx/7xx
series. Well done to all involved and hopefully this will help ARM
head in the right direction.
There is also now the ability if you don't have any of the legacy
drivers enabled (pre-KMS) to remove all the pre-KMS support code from
the core drm, this saves 10% or so in codesize on my machine.
i915 also enable Icelake/Elkhart Lake Gen11 GPUs by default, vboxvideo
moves out of staging.
There are also some rcar-du patches which crossover with media tree
but all should be acked by Mauro.
Summary:
uapi changes:
- Colorspace connector property
- fourcc - new YUV formts
- timeline sync objects initially merged
- expose FB_DAMAGE_CLIPS to atomic userspace
new drivers:
- vboxvideo: moved out of staging
- aspeed: ASPEED SoC BMC chip display support
- lima: ARM Mali4xx GPU acceleration driver support
- panfrost: ARM Mali6xx/7xx Midgard/Bitfrost acceleration driver support
core:
- component helper docs
- unplugging fixes
- devm device init
- MIPI/DSI rate control
- shmem backed gem objects
- connector, display_info, edid_quirks cleanups
- dma_buf fence chain support
- 64-bit dma-fence seqno comparison fixes
- move initial fb config code to core
- gem fence array helpers for Lima
- ability to remove legacy support code if no drivers requires it (removes 10% of drm.ko size)
- lease fixes
ttm:
- unified DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
panel:
- OSD070T1718-19TS panel support
- panel-tpo-td028ttec1 backlight support
- Ronbo RB070D30 MIPI/DSI
- Feiyang FY07024DI26A30-D MIPI-DSI panel
- Rocktech jh057n00900 MIPI-DSI panel
i915:
- Comet Lake (Gen9) PCI IDs
- Updated Icelake PCI IDs
- Elkhartlake (Gen11) support
- DP MST property addtions
- plane and watermark fixes
- Icelake port sync and VEBOX disable fixes
- struct_mutex usage reduction
- Icelake gamma fix
- GuC reset fixes
- make mmap more asynchronous
- sound display power well race fixes
- DDI/MIPI-DSI clocks for Icelake
- Icelake RPS frequency changing support
- Icelake workarounds
amdgpu:
- Use HMM for userptr
- vega20 experimental smu11 support
- RAS support for vega20
- BACO support for vega12 + fixes for vega20
- reworked IH interrupt handling
- amdkfd RAS support
- Freesync improvements
- initial timeline sync object support
- DC Z ordering fixes
- NV12 planes support
- colorspace properties for planes=
- eDP opts if eDP already initialized
nouveau:
- misc fixes
etnaviv:
- misc fixes
msm:
- GPU zap shader support expansion
- robustness ABI addition
exynos:
- Logging cleanups
tegra:
- Shared reset fix
- CPU cache maintenance fix
cirrus:
- driver rewritten using simple helpers
meson:
- G12A support
vmwgfx:
- Resource dirtying management improvements
- Userspace logging improvements
virtio:
- PRIME fixes
rockchip:
- rk3066 hdmi support
sun4i:
- DSI burst mode support
vc4:
- load tracker to detect underflow
v3d:
- v3d v4.2 support
malidp:
- initial Mali D71 support in komeda driver
tfp410:
- omap related improvement
omapdrm:
- drm bridge/panel support
- drop some omap specific panels
rcar-du:
- Display writeback support"
* tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm: (1507 commits)
drm/msm/a6xx: No zap shader is not an error
drm/cma-helper: Fix drm_gem_cma_free_object()
drm: Fix timestamp docs for variable refresh properties.
drm/komeda: Mark the local functions as static
drm/komeda: Fixed warning: Function parameter or member not described
drm/komeda: Expose bus_width to Komeda-CORE
drm/komeda: Add sysfs attribute: core_id and config_id
drm: add non-desktop quirk for Valve HMDs
drm/panfrost: Show stored feature registers
drm/panfrost: Don't scream about deferred probe
drm/panfrost: Disable PM on probe failure
drm/panfrost: Set DMA masks earlier
drm/panfrost: Add sanity checks to submit IOCTL
drm/etnaviv: initialize idle mask before querying the HW db
drm: introduce a capability flag for syncobj timeline support
drm: report consistent errors when checking syncobj capibility
drm/nouveau/nouveau: forward error generated while resuming objects tree
drm/nouveau/fb/ramgk104: fix spelling mistake "sucessfully" -> "successfully"
drm/nouveau/i2c: Disable i2c bus access after ->fini()
drm/nouveau: Remove duplicate ACPI_VIDEO_NOTIFY_PROBE definition
...
[Why]
The type of 'r' is uint32_t and the return codes for both:
- reservation_object_wait_timeout_rcu
- amdgpu_bo_reserve
...are signed. While it works for the latter since the check is
done on != 0 it doesn't work for the former since we check <= 0.
[How]
Make 'r' a long in commit planes so we're not doing any unsigned/signed
conversion here in the first place.
v2: use long instead of int (Christian)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pre-DCE12 needs special treatment for BTR / low framerate
compensation for more stable behaviour:
According to comments in the code and some testing on DCE-8
and DCE-11, DCE-11 and earlier only apply VTOTAL_MIN/MAX
programming with a lag of one frame, so the special BTR hw
programming for intermediate fixed duration frames must be
done inside the current frame at flip submission in atomic
commit tail, ie. one vblank earlier, and the fixed refresh
intermediate frame mode must be also terminated one vblank
earlier on pre-DCE12 display engines.
To achieve proper termination on < DCE-12 shift the point
when the switch-back from fixed vblank duration to variable
vblank duration happens from the start of VBLANK (vblank irq,
as done on DCE-12+) to back-porch or end of VBLANK (handled
by vupdate irq handler). We must leave the switch-back code
inside VBLANK irq for DCE12+, as before.
Doing this, we get much better behaviour of BTR for up-sweeps,
ie. going from short to long frame durations (~high to low fps)
and for constant framerate flips, as tested on DCE-8 and
DCE-11. Behaviour is still not quite as good as on DCN-1
though.
On down-sweeps, going from long to short frame durations
(low fps to high fps) < DCE-12 is a little bit improved,
although by far not as much as for up-sweeps and constant
fps.
v2: Fix some wrong locking, as pointed out by Nicholas.
v3: Simplify if-condition in vupdate-irq - nit by Nicholas.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The comparison of inserted_frame_duration_in_us against a
duration calculated from max_refresh_in_uhz is both wrong
in its math and not needed, as the min_duration_in_us value
is already cached in in_out_vrr for reuse. No need to
recalculate it wrongly at each invocation.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RGB565 support isn't restricted to just the primary plane in DC, so
also expose support for it on overlays.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Originally we did the amdgpu_dm_handle_vrr_transition call before
interrupts were enabled. After the interrupt toggling logic was
moved around for support enabling CRTCs with no primary planes
active this was no longer being called in the case where there
wasn't a modeset.
This fixes failures in igt@kms_vrr@* with error
"Timed out: Waiting for vblank event".
[How]
Shift them back into the loop that always ran before interrupts were
enabled.
Pull out the logic that updated VRR state into the same loop since
there's no reason these need to be split.
In the case where we're going from VRR off, no planes to VRR on, some
active planes we'll still be covered for having the VRR vupdate
handler enabled - vblank will be re-enabled at this point, it will
see that VRR is active and set the vupdate interrupt on there.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Refactor dp vendor parsing int to a new function, and call it before
get_active_converter_info().
Also, add a flag to skip parsing of Display ID 2.0. Some devices fail on
readind DID2, but we shouldn't fail EDID read because of it. Add this
flag to facilitate the logic.
Signed-off-by: John Barberiz <John.Barberiz@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Different HW will need to init HUBP differently. For now, add a vtable
entry, and hook a NO-OP for DCN1.
In addition, future HW will need to access the HUBPREQ_DEBUG register
for hubp_init. Add it to the reg list.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new interface now replaces the old interface for all known
configurations.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the generic introduction of seamless boot, the display is no
longer blanked upon boot. However, this causes corruption on some
systems that does not lock the memory in the non-secure boot case,
resulting in brief corruption on boot due to garbage being written into
the frame buffer.
[How]
Add a flag, read during DC init, to determine whether display should be
blanked on boot. Default to true.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Replace certain register writes with register sets that overwrites the
the entire register, instead of only a field within the register.
* Add program_watermarks() entry to hubbub vtable. Hook it up to
existing functions that program watermarks.
* Add additional watermark registers.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many userspace applications (and IGT) seem to expect that most drivers
can keep a CRTC active and enabled if there are no primary or overlay
planes.
DC is setup to handle this but only in the case where there are
absolutely no planes on the CRTC - no primary, cursor, or overlay.
[How]
Add a check to reject commits that have cursor planes enabled and
nothing else on CRTCs since we can't handle that. The new helper
does_crtc_have_active_cursor is used for this.
In atomic commit tail, we need to let DC know that there are zero
planes enabled when doing stream updates to let it disable and blank
pipes as appropriate.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When disabling all the pipes for a CRTC the page-flip interrupt also
gets disabled on Raven. We can't re-enable the page-flip interrupt
unless we give DC at least one active DC plane.
We currently enable interrupts after the call to dc_commit_state since
there's currently no valid sequence that should disable all the planes
or re-enable planes for a CRTC without first going through
dc_commit_state.
If we were to allow for a CRTC to be enabled with no primary plane this
would not be the case - the call to dc_commit_updates_for_stream would
enable the planes when going from zero to at least one active plane,
but manage_dm_interrupts would have been called too early.
This results in a page-flip timeout on any subsequent commits since we
think the page-flip are now enabled when they're actually disabled.
We need to enable interrupts after the call to
dc_commit_updates_for_stream.
[How]
Split enabling interrupts into two passes. One pass before
dc_commit_updates_for_stream and one after it.
Shifting all the interrupts to be strictly below the call doesn't
currently work even though it should in theory. We end up queuing
off the vblank event to be handle by the flip handler before it's
actually enabled in some cases, particularly:
old_crtc_state->active = false -> new_crtc_state->active = true
The framebuffer states haven't changed and we can technically still
do a "pageflip" in this case and send back the event.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We only currently drop the vblank reference when the stream is
being removed from the context. We should be dropping it whenever we
disable interrupts and reaquiring it after we re-enable them.
We also never get the extra reference correctly when re-enabling
interrupts, since grabbing the reference has the following condition:
if (!crtc_state->crc_enabled && enable)
drm_crtc_vblank_get(crtc);
This means that crc_enabled must be *false* in order to grab the extra
reference.
[How]
Always drop the ref whenever we're disabling interrupts.
Only disable CRC capture when the stream is being removed.
Always grab the ref by setting dm_new_crtc_state->crc_enabled = false
before the call to re-enable CRC capture.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can't do cursor programming after the planes have been disabled
since there won't be any pipes - leading to lock warnings and the wrong
cursor state being left in the registers.
When we re-enable the planes after the previous cursor state will also
remain if we don't have a cursor plane.
[How]
If we're disabling the planes then do the cursor programming first.
If we're not disabling the planes then do the cursor programming after.
Introduce the amdgpu_dm_commit_cursors helper to avoid code duplication
for both of these cases.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The vblank and pageflip interrupts should only be enabled for a CRTC
that's enabled and has active planes.
The current logic takes care of this, but isn't setup to handle the case
where the active plane count goes to zero but the stream remains
enabled.
We currently block this case since we don't allow commits that enable a
CRTC with no active planes, but shouldn't be any reason we can't support
this from a hardware perspective and many userspace applications expect
to be able to do it (like IGT).
[How]
The count_crtc_active_planes function fills in the number of
"active_planes" on the dm_crtc_state. This should be the same as
DC's plane_count on the stream_status but easier to access since we
don't need to lock the private atomic state with the DC context.
Add the "interrupts_enabled" flag to the dm_crtc_state and set it based
on whether the stream exists and if there are active planes on the
stream.
Update the disable and enable logic to make use of this new flag.
There shouldn't be any functional change (yet) with this patch.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently an allocation is being made but the allocation failure
check is being performed on another pointer. Fix this by checking
the correct pointer. Also use the normal kernel idiom for null
pointer checks.
Addresses-Coverity: ("Resource leak")
Fixes: 43e3ac8389 ("drm/amd/display: Add function to copy DC streams")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add the amdgpu specific bits for timeline support
- Add internal interfaces for xgmi pstate support
- DC Z ordering fixes for planes
- Add support for NV12 planes in DC
- Add colorspace properties for planes in DC
- eDP optimizations if the GOP driver already initialized eDP
- DC bandwidth validation tracing support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419150034.3473-1-alexander.deucher@amd.com
[why]
When DMCU interrupts x86, it leads to undefined phy programming
[how]
expand dmcu interface to support new PHY lock and unlock commands
if DMCU FW doesn't support these commands, they fail silently so its okay
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting with DCN1, the input_pixel_processor (ipp) struct has been
replaced by dpp struct (part of DAL3.1 SW architecture change).
Need to update logic to handle cases where ipp is never allocated.
[How]
Only skip cursor position programming if both ipp and dpp resources
are NULL.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Power down of PHY on eDP requires us to call eDP power
control to power on again
[How]
1. In the case link rates don't match, disable PHY
requires calling of eDP power control ON after
2. Link disable case limit to eDP path since
this is not really applicable to DP since we do
power down PHY as part of verify link cap
3. Move detection of eDP link settings to be
done even for S4 resume cases where other
dpcd cap read and edid read can be skipped
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some DMCU messages were being sent in cases where
there was no DMCU FW at all, which resulted in some wait
timeouts
[How]
Delay sending some of the DMCU messages after FW
init is called and DMCU is running.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We'll need the ability to copy a dc_stream_state for some features.
Implement it here.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Workaround was missing in one HW disable path,
meaning when all pipes are power gated, stutter was
not working
[How]
Add workaround for init_hw path for stutter
workaround
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Patch '5edb0c9b Fix deadlock with display during hanged ring recovery'
was accidentaly removed during one of DALs code merges.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't block others while waiting for the fences to finish, concurrent
submission is perfectly valid in this case and holding the lock can
prevent killed applications from terminating.
Signed-off-by: Christian König <ckoenig.leichtzumerken@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC and DM already support DRM_FORMAT_RGB565, it's just missing from the
list of valid formats.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We used this change to investigate the performance of bandwidth validation,
it will be useful to have if we need to investigate further.
[How]
We use performance counter tick numbers to profile performance, they live
at dc->debug.bw_val_profile (set .enable in debugger to turn on measuring).
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a fast_validate parameter in dc_validate_global_state for future use
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
As long as we have at least one non-cursor plane enabled on a CRTC then
the CRTC itself can remain enabled.
This will allow for commits where there's an overlay plane enabled but
no primary plane enabled.
[How]
Remove existing primary plane fb != NULL checks and replace them with
the new does_crtc_have_active_plane helper.
This will be called from atomic check when validating the CRTC.
Since the primary plane state can now potentially be NULL we'll need
to guard for that when accessing it in some of the cursor logic.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Surface scaling info updates can affect bandwidth and blocks. We need
to be checking these with global validation to avoid underflow or
corruption.
[How]
Drop the state->allow_modeset early exit in
dm_determine_update_type_for_commit. Most of those should be considered
fast now anyway.
Fill in scaling info and it to the surface update in atomic
check.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM thinks that the update type should be full whenever a stream or
plane is added or removed (including recreations).
This won't match in the case where DC thinks what looks like a fast
update to DM is actually a medium or full - like scaling changes that
affect bandwidth and clocks.
[How]
Drop this warning. DC knows better than the DM does for determining
cases like this.
The other warning can be kept for now since it would warn on a pretty
serious DC or DM bug.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC expects the surface memory address to identify the surface.
This doesn't work with what we're doing with the temporary surfaces,
it will always assume this is a full update because the surface
isn't in the current context.
[How]
Use the surface directly. This doesn't give us much improvement yet,
since we always create a new dc_plane_state when state->allow_modeset
is true.
The call into dc_check_update_surfaces_for_stream also needs to be
locked, for two reasons:
1. It checks the current DC state
2. It modifies the surface update flags
Both of which could be currently in the middle of commit work from
commit tail.
A TODO here is to pass the context explicitly into this function and
find a way to get the surface update flags out of it without modifying
the surface in place.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Planes have downscaling limits and upscaling limits per format and DM
is expected to validate these using DC caps. We should fail atomic
check validation if we aren't capable of doing the scaling.
[How]
We don't currently create store which DC plane maps to which DRM plane
so we can't easily check the caps directly. For now add basic
constraints that cover the absolute min and max downscale / upscale
limits for most RGB and YUV formats across ASICs.
Leave a TODO indicating that these should really be done with DC caps.
We'll probably need to subclass DRM planes again in order to correctly
identify which DC plane maps to it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM doesn't need to know which link cap is being retrieved ( verified
or preferred ). Let DC figure it out.
[How]
Change name.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We currently don't do DC validation for medium or full updates where
the plane state isn't created. There are some medium and full updates
that can cause bandwidth or clock changes to occur resulting in
underflow or corruption.
We need to be able to fill surface and plane info updates during
atomic commit for dm_determine_update_type for commit. Since we already
do this during atomic commit tail it would be good if we had the same
logic in both places for creating these structures.
[How]
Introduce fill_dc_scaling_info and fill_dc_plane_info_and_addr.
These two functions cover the following three update structures:
- struct dc_scaling_info
- struct dc_plane_info
- struct dc_plane_address
Cleanup and adapter the existing fill_plane_* helpers to work with
these functions.
Update call sites that used most of these sub helpers directly to work
with the new functions. The exception being prepare_fb - we just want
the new buffer attributes specifically in the case where we're
creating the plane. This is needed for dc_commit_state in the case
where the FB hasn't been previously been used.
This isn't quite a refactor, but functionally driver behavior should
be mostly the smae as before. The one exception is that we now check
the return code for fill_plane_buffer_attributes which means that
commits will be rejected that try to enable DCC with erroneous
parameters.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pitch was only calculated based on format whenever the plane state
was recreated. This could result in surface corruption due to the
incorrect pitch being programmed when the surface pitch changed during
commits where state->allow_modeset = false.
[How]
Recalculate pitch at the same time we update the buffer address and
other buffer attributes. This function was previously called
fill_plane_tiling_attributes but I've also renamed it to
fill_plane_buffer_attributes to clarify the actual intent of the
function now that it's handling most buffer related attributes.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The overlay will be incorrectly placed *below* the primary plane for
commits with state->allow_modeset = true because the primary plane
won't be removed and recreated in the same commit.
[How]
Add the should_reset_plane helper to determine if the plane should be
reset or not. If we need to add or force reset any plane in the context
then we'll need to do the same for every plane on the stream.
Unfortunately we need to do the remove / recreate routine for removing
planes as well since DC currently isn't well equipped to handle the
plane with the top pipe being removed with other planes still active.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Plane scaling parameters are not correctly filled or updated when
performing fast updates.
They're filled when creating the dc plane state and during atomic check.
While the atomic check code path happens for the plane even during fast
updates, the issue is that they're done in place on the dc_plane_state
directly. This dc_plane_state may be the current state plane state
being used by the hardware, so these parameters won't be correctly
programmed.
The new scaling parameters should instead be passed as an update
to the plane.
[How]
Update fill_rects_from_plane_state to not modify dc_plane_state
directly. Update the call sites that use this to fill in the appropriate
values.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unlike external DP panels, internal eDP does not perform
verify link caps because the panel connection is fixed.
So if GOP enabled the eDP at boot, we can retain its
trained link settings to optimize.
[How]
Read the lane count and link rate by reading this
information from DPCD 100h, 101h, 115h
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_stream_get_crtc_position can return false.
This was unhandled in delay_cursor_until_vupdate
[How]
If dc_stream_get_crtc_position returns false, something
is weird. Don't delay.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
there are some scaling capabilities such as fp16 which are known to be unsupported
on a given ASIC. exposing these static capabilities allows much simpler implementation
for OS interfaces which require to report such static capabilities to reduce the
number of dynamic validation calls
[how]
refactor the existing plane caps to be more extensible, and add fp16 and scaling
capabilities
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need DC's color space to match the color encoding and color space
specified by userspace to correctly render YUV surfaces.
[How]
Add the DRM color properties when the DC plane supports NV12.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardware can support video surfaces and DC tells us which planes are
suitable via DC plane caps.
[How]
The supported formats array will now vary based on what DC tells us,
so create an array and fill it dynamically based on plane types and
caps.
Ideally we'd query support for every format via DC plane caps, but for
the framework is in place to do so later with this.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some LED Driver might not like Fractional PWM especially at extreme
ranges near 0% or 100%.
For example, backlight flashing could be observed.
We want a way to switch fractional PWM on/off either for debug, or
possibly production.
[How]
Add DC code that can send new FW command to enable/disable
fractional PWM.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some compositors, with two monitors attached, VT terminal
switch can cause a graphical issue by the following means:
There are two streams, one for each monitor. Each stream has one
plane
current state:
M1:S1->P1
M2:S2->P2
The user calls for a terminal switch and a commit is made to
change both planes to linear swizzle mode. In atomic check,
a new dc_state is constructed with new planes on each stream
new state:
M1:S1->P3
M2:S2->P4
In commit tail, each stream is committed, one at a time. The first
stream (S1) updates properly, triggerring a full update and replacing
the state
current state:
M1:S1->P3
M2:S2->P4
The update for S2 comes in, but dc detects that there is no difference
between the stream and plane in the new and current states, and so
triggers a fast update. The fast update does not program swizzle,
so the second monitor is corrupted
[How]
Add a flag to dc_plane_state that forces full updates
When a stream undergoes a full update, set this flag on all changed
planes, then clear it on the current stream
Subsequent streams will get full updates as a result
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
AUX takes longer to reply when using active DP-DVI dongle on some asics
resulting in up to 2000+ us edid read (timeout).
[How]
1. Adjust AUX poll to match spec
2. Extend the SW timeout. This does not affect normal
operation since we exit the loop as soon as AUX acks.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Simply return true/false, don't iterate up the tree.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When deciding to add properties or expose formats on DRM planes we
should be querying the caps for the DC plane it's supposed to represent.
[How]
Pass plane caps down into plane initialization, refactoring overlay
plane initialization to have the overlay plane be represented by
the first overlay capable DC plane.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn*_disable_plane() doesn't unlock the pipe anymore, making the extra
lock unnecessary.
In addition - during full plane updates - all necessary pipes should be
locked/unlocked together when modifying hubp to avoid tearing in
pipesplit setups.
[How]
Remove redundant locks, and add function to lock all pipes. If an
interdependent pipe update is required, lock down all pipes. Otherwise,
lock only the top pipe for the updated pipe tree.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When entering S3, amdgpu first calls DRM to cache the current atomic
state, then commit the 'all-disabled' state. This sets dc->current_state
to point at the private atomic object's dm_atomic_state->context, as
any regular atomic commit would.
Afterwards, amdgpu_dm calls dc_set_power_state() with S3 power state.
This invalidates dc->current_state by wiping it to 0, consequently
wiping dm_atomic_state->context.
During resume, the cached atomic state is restored. When getting the
private object however, the dm_atomic_state - containing the wiped
context - is duplicated into the atomic state. This causes DC validation
to fail during atomic check, as necessary function pointers in dc_state
are now NULL.
[How]
Recreate the private object's dm_atomic_state->context during resume,
restoring any static values such as function pointers.
A TODO item is added to move static read-only values out of dc_state -
they shouldn't be there anyways.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Checking against a TF that is unused causes us to default to black
[How]
Check against PQ instead
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
New seamless boot sequence introduced a bug where front end is disabled
without blanking otg.
[How]
Adjust the condition of blanking otg to match seamless boot.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If link is already enabled at a different rate (for example 5.4 Gbps)
then calling VBIOS command table to switch to a new rate
(for example 2.7 Gbps) will not take effect.
This can lead to link training failure to occur.
[How]
If the requested link rate is different than the current link rate,
the link must be disabled in order to re-enable at the new
link rate.
In today's logic it is currently only impacting eDP since DP
connection types will always disable the link during display
detection, when initial link verification occurs.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some cases we want DC init to take in some config options
[How]
Init dc_config before rest of DC init
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In HDR configurations, the cursor - in SDR - needs to have it's white
level boosted.
[How]
Program the cursor boost in update_dchubp_dpp like the other cursor
attributes.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need DC's color space to match the color encoding and color space
specified by userspace to correctly render YUV surfaces.
[How]
Convert the DRM color encoding and color range properties to the
appropriate DC colorspace option and update the color space when
performing surface updates.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
when preferred link cap is set, we should always use
preferred in all validation.
we should not use preferred for some validation but use
verified for others.
[how]
create getter function that gets verified link cap.
if preferred is set, return preferred link settings instead.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Image brightness compensation for solid color full screen images is
expected to be optimal for ABM 2.2 at level 3. The min reduction that is
currently being enforced prevents this from being achieved.
[How]
Remove the min reduction for ABM 2.2 at level 3
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before it was returning false in the case of failure even though return type should be enum dc_status
[How]
Return DC_FAIL_UNSUPPORTED_1 instead
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The input color space for the plane was previously ignored even if it
was set.
If a limited range YUV format was given to DC then the
wrong color transformation matrix was being used since DC assumed that
it was full range instead.
[How]
Respect the given color_space format for the plane if it isn't
COLOR_SPACE_UNKNOWN. Otherwise, use the implicit default since DM
didn't specify.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently link bandwidth is calculated in two places, using the same
formula. They should be unified into calling one function.
[how]
Replace all implementations of link bandwidth calculation with a call
to a function.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clk_mgr is called dccg in dc_state, this change fixes that
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The existing calculation uses a wrong formula to
calculate bandwidth from timing.
[how]
Expose the existing proper function that calculates the bandwidth,
so dc_link can use it to calculate timing bandwidth correctly.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We are incorrectly using dp_hdmi_max_pixel_clk because the units are not clear.
[How]
Rename to dp_hdmi_max_pixel_clk_in_khz, and change mode timing validation to use
the value correctly.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC provides a few visual confirmation debug options that can be
dynamically changed at runtime to help debug surface programming issues
but we don't have any way to access it from userspace.
[How]
Add the amdgpu_dm_visual_confirm debugfs entry.
It accepts a string containing the DC visual confirm enum value using
the debugfs attribute helpers.
The debugfs_create_file_unsafe can be used instead of
debugfs_create_file as per the documentation.
v2: Use debugfs helpers for getting and setting the value (Christian)
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The brace initialization used here generates warnings on some
compilers. For example, on GCC 4.9:
[...] In function ‘dm_determine_update_type_for_commit’:
[...] error: missing braces around initializer [-Werror=missing-braces]
struct dc_stream_update stream_update = { 0 };
^
Use memset to make this more portable.
v2: Specify the compiler / diagnostic in the commit message (Paul)
Cc: Sun peng Li <Sunpeng.Li@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
v2: add hunk that got dropped accidently when this patch was originally
committed. (Alex)
Fixes: 0921c41e19 ("drm/amd/display: Fix negative cursor pos programming")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
the member sdr_white_level of struct dc_cursor_attributes was not
initialized, then the random value result that
dcn10_set_cursor_sdr_white_level() set error hw_scale value 0x20D9(normal
value is 0x3c00), this cause the black cursor issue.
[how]
just initilize the obj of struct dc_cursor_attributes to zero to avoid
the random value.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Tianci Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The actual position for the cursor on the screen is essentially:
x_out = x - x_plane - x_hotspot
y_out = y - y_plane - y_hotspot
The register values for cursor position and cursor hotspot need to be
greater than zero when programmed, but we also need to subtract off
the plane position to display the cursor at the correct position.
Since we don't want x or y to be less than zero, we add the plane
position as a positive value to x_hotspot or y_hotspot. However, what
this doesn't take into account is that the hotspot registers are limited
by the maximum cursor size.
On DCN10 the cursor hotspot regitsers are masked to 0xFF, so they have
a maximum value of 0-255. Values greater this will wrap, causing the
cursor to display in the wrong position.
In practice this means that for sufficiently large plane positions, the
cursor will be drawn twice on the screen, and can cause screen flashes
or p-state WARNS depending on what the wrapped value is.
So we need a way to remove the value from x_plane and y_plane without
exceeding the maximum cursor size.
[How]
Subtract as much as x_plane/y_plane as possible from x and y and place
the remainder in the cursor hotspot register.
The value for x_hotspot and y_hotspot can still wrap around but it
won't happen in a case where the cursor is actually enabled.
The cursor plane needs to intersect at least one pixel of the plane's
rectangle to be enabled, so the cursor position + hotspot provided by
userspace must always be strictly less than the maximum cursor size for
the cursor to actually be enabled.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DCN disabled builds, dc->dml is stripped out. Therefore, guard usage
in dc_create_state() with CONFIG_DRM_AMD_DC_DCN1_0.
It fixes the following error:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c: In function 'dc_create_state':
>> drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:1237:34: error: 'struct dc' has no member named 'dml'
memcpy(&context->bw_ctx.dml, &dc->dml, sizeof(struct display_mode_lib));
^~
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Multiple threads were writing back to one global VBA in DC resulting
in multiple threads overwriting eachother's data
[How]
Add an instance of DML (which contains VBA) to each context and
change all calls that used dc->dml to use context->dml. Created a
seperate copy constructor for linux in a case where there is no
access to DC.
Signed-off-by: Aidan Wood <Aidan.Wood@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want vblank counts and timestamps of flip completion as sent
in pageflip completion events to be consistent with the vblank
count and timestamp of the vblank of flip completion, like in non
VRR mode.
In VRR mode, drm_update_vblank_count() - and thereby vblank
count and timestamp updates - must be delayed until after the
end of front-porch of each vblank, as it is only safe to
calculate vblank timestamps outside of the front-porch, when
we actually know when the vblank will end or has ended.
The function drm_update_vblank_count() which updates timestamps
and counts gets called by drm_crtc_accurate_vblank_count() or by
drm_crtc_handle_vblank().
Therefore we must make sure that pageflip events for a completed
flip are only sent out after drm_crtc_accurate_vblank_count() or
drm_crtc_handle_vblank() is executed, after end of front-porch
for the vblank of flip completion.
Two cases:
a) Pageflip irq handler executes inside front-porch:
In this case we must defer sending pageflip events until
drm_crtc_handle_vblank() executes after end of front-porch,
and thereby calculates proper vblank count and timestamp.
Iow. the pflip irq handler must just arm a pageflip event
to be sent out by drm_crtc_handle_vblank() later on.
b) Pageflip irq handler executes after end of front-porch, e.g.,
after flip completion in back-porch or due to a massively
delayed handler invocation into the active scanout of the new
frame. In this case we can call drm_crtc_accurate_vblank_count()
to safely force calculation of a proper vblank count and
timestamp, and must send the pageflip completion event
ourselves from the pageflip irq handler.
This is the same behaviour as needed for standard fixed refresh
rate mode.
To decide from within pageflip handler if we are in case a) or b),
we check the current scanout position against the boundary of
front-porch. In non-VRR mode we just do what we did in the past.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In VRR mode, proper vblank/pageflip timestamps can only be computed
after the display scanout position has left front-porch. Therefore
delay calls to drm_crtc_handle_vblank(), and thereby calls to
drm_update_vblank_count() and pageflip event delivery, to after the
end of front-porch when in VRR mode.
We add a new vupdate irq, which triggers at the end of the vupdate
interval, ie. at the end of vblank, and calls the core vblank handler
function. The new irq handler is not executed in standard non-VRR
mode, so vblank handling for fixed refresh rate mode is identical
to the past implementation.
v2: Implement feedback by Nicholas and Paul Menzel.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For throttling to work correctly, we always need a baseline vblank
count last_flip_vblank that increments at start of front-porch.
This is the case for drm_crtc_vblank_count() in non-VRR mode, where
the vblank irq fires at start of front-porch and triggers DRM core
vblank handling, but it is no longer the case in VRR mode, where
core vblank handling is done later, after end of front-porch.
Therefore drm_crtc_vblank_count() is no longer useful for this.
We also can't use drm_crtc_accurate_vblank_count(), as that would
screw up vblank timestamps in VRR mode when called in front-porch.
To solve this, use the cooked hardware vblank counter returned by
amdgpu_get_vblank_counter_kms() instead, as that one is cooked to
always increment at start of front-porch, independent of when
vblank related irq's fire.
This patch allows vblank irq handling to happen anywhere within
vblank of even after it, without a negative impact on flip
throttling, so followup patches can shift the vblank core
handling trigger point wherever they need it.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During VRR mode we can not allow vblank irq dis-/enable
transitions, as an enable after a disable can happen at
an arbitrary time during the video refresh cycle, e.g.,
with a high likelyhood inside vblank front-porch. An
enable during front-porch would cause vblank timestamp
updates/calculations which are completely bogus, given
the code can't know when the vblank will end as long
as we are in front-porch with no page flip completed.
Hold a permanent vblank reference on the crtc while
in active VRR mode to prevent a vblank disable, and
drop the reference again when switching back to fixed
refresh rate non-VRR mode.
v2: Make sure transition is also handled if vrr is
disabled and stream gets disabled in the same
atomic commit by moving the call to the transition
function outside of plane commit.
Suggested by Nicholas.
v3: Trivial rebase onto previous patch.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need the VRR active/inactive state info earlier in
the commit sequence, so VRR related setup functions like
amdgpu_dm_handle_vrr_transition() know the final VRR state
when they need to do their hw setup work.
Split update_freesync_state_on_stream() into an early part,
that can run at the beginning of commit tail before the
vrr transition handling, and a late part that must run after
vrr transition handling inside the commit planes code for
enabled crtc's.
Suggested by Nicholas Kazlauskas.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu:
- Switch to HMM for userptr (reverted until HMM fixes land)
- New experimental SMU 11 replacement for powerplay for vega20 (not enabled by default)
- Initial RAS support for vega20
- BACO support for vega12
- BACO fixes for vega20
- Rework IH handling for page fault and retry interrupts
- Cleanly split CPU and GPU paths for GPUVM updates
- Powerplay fixes
- XGMI fixes
- Rework how DC interacts with atomic for planes
- Clean up and simplify DC/Powerplay interfaces
- Misc cleanups and bug fixes
amdkfd:
- Switch to HMM for userptr (reverted until HMM fixes land)
- Add initial RAS support
- MQD fixes
ttm:
- Unify DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
- Misc cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190402170820.22197-1-alexander.deucher@amd.com
Currently only top pipe gets output tf programmed. This change
makes all odm head pipes get output tf programmed.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Create a functions to return swizzle types for dml
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pass SDP splitting when setting stream attributes for future use
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Create dccg_init and init_clocks for future use
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
set_display_requirement, dcn1_pplib_apply_display_requirements
are no longer used and should be removed.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The resource constructor currently needs num_virtual_links from
init_data but will need access to other items provided by DM.
[HOW]
Pass init_data into DCN create_resource_pool functions.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When you have a SST branch device the driver, Even no sink device connected,
it also send HPD with a valid EDID. Driver will config it to DP sink.
Therefore, there're two displays in display setting.
DPCD 0x05, DFP_PRESENT = 1 (branch device),
DFP_TYPE = 00 (Display Port)
[How]
Driver determine DPCD 0x05 DFP_PRESENT = 1(branch) as an active dongle
And check DFP count.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
program default output gamma if no user specific gamma
parameters passed.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
existing logic finds "first free pipe from 5 -> 0" to split
this will cause certain sequences to require DC to move
an MPCC from one tree to another, which is unsupported
this leads to blackscreen
to mitigate this problem, we will always try to acquire the
"preferred" pipe, and each pipe has a unique preferred pipe
this means we avoid most of the scenarios where
pipe splitting leads to moving MPCC from one tree
to another
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBIOS will not post pixel rate > 340MHz.
If driver set pixel rate > 340MHz and do restart bottom, VBIOS can't
post HDMI monitor due to monitor is stay in HDMI2.0 state.
[How]
Program Scrambling_Enable and TMDS_Bit_Clock_Ratio when disable stream.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Black screens or artifacting can occur when enabling FreeSync outside
of the supported range of the monitor. This can happen since the
supported range isn't always the min/max vrefresh range available for
the monitor.
[How]
There was previously a fix that prevented this from happening in the
low range but it didn't cover the upper range. Expand the condition
to include both.
Cc: Sun peng Li <Sunpeng.Li@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leads to an undefined symbol otherwise.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want DRM planes to be initialized in the following order:
- primary planes
- overlay planes
- cursor planes
to support existing userspace expectations for plane z-ordering. This
means that we also need to register CRTCs after all planes have been
initialized since overlay planes can be placed on any CRTC.
So the only reason why we have the mode_info->planes list is to
remember the primary planes for use later when we need to register
the CRTC.
Overlay planes have no purpose being in this list. DRM will cleanup
any planes that we've registered for us, so the only planes that need to
be explicitly cleaned up are the ones that have failed to register.
By dropping the explicit free on every plane in the mode_info->planes
list this patch also fixes a double-free in the case where we fail to
initialize only some of the planes.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need arbitrary read/write over DP AUX DPCD
for debugging
[How]
Three debugfs entries
Set the target address by writing to
"aux_dpcd_address"
(The first four bytes written are used)
Set the transaction size in bytes by writing to
"aux_dpcd_size"
(The first four bytes written are used)
Start a transaction by reading/writing
"aux_dpcd_data"
Do note: there is no concerrency protection at all
Accessing these entries in quick succession can lead
to strange behaviour
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to add DP SDP message test debugfs to make sdp message test
more convenient and efficient.
[How]
Add sdp_message debugfs entry in amdgpu.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to add DP SDP message test debugfs to make sdp message test
more convenient and efficient.
[How]
Add a DM accessible SDP interface for custom data.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are issues removing surfaces/streams when odm is active.
This is a step to fix that
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A number of places opp programming was missing for odm second pipe.
This change fixes the oversight.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We fail to reset the second odm combine pipe. This change fixes
odm pointer management.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Releasing planes should not release the 2nd odm pipe right away,
this change leaves us with 2 pipes with null planes and same stream
when planes are released during odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Refactor setting bit fields. Correcting the offset of MD0.
Initializing the InfoPacket header fields. Defining the field offsets
and masks.
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain cases we do link training when we don't have a backend.
[How]
In dc_link_set_preferred_link_settings(), store preferred link settings
first and then verify that the link is DP and the link stream's backend is
enabled. If either is false, then we will not do any link retraining.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add these interfacese for future use
setup_global_lock()
lock_global()
pipe_control_lock_global()
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we are missing a few checks to see if HDR10 is allowed.
In particular we never check for the extended colorimetry bit (whether its
present or set to 1). Further we don't read in the dpcd block in DC that
would provide these bits.
[How]
- Added in DC code to read in the block containing the extended colorimetry
bit.
Signed-off-by: Harmanprit Tatla <Harmanprit.Tatla@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Somewhere in the atomic check reshuffle ABM got lost.
ABM is a crtc property (copied from a connector property).
It can change without a modeset, just like underscan.
[How]
In the skip_modeset branch of atomic check crtc updates,
copy over the abm property.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In HDMI plugfest, MTK report our EMP with VRR_EN bit = 0.
VRR_EN bit is EMP-MD0-bit 0. Currently driver set 1 to bit 3.
[How]
Programming correct VRR_EN bit in EMP-MD0-bit0.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Reza Amini <Reza.Amini@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There exist displays with EDIDs > 512 bytes, existing code
will cause us to ignore all extension blocks.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Audio was unmuted for HDMI only, need to do so for DP as well.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Flickering is observed on some displays when the number of inserted BTR
frames changes frequently.
[How]
Add in a margin of drift to prevent the inserted number of frames from
jumping around too frequently.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
when programming VID_TIMING, we were using the original VESA timing for DP_VIDM/N.
for YCbCr420 or compressed YCbCr422, using half rate as YCbCr444.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to set VID_N_MUL for 4:2:0 cases
[How]
Move setting to enc1_stream_encoder_dp_unblank and
ensure it is also set for non-4:2:0 cases.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move out of header to dc_helper.c, in preparation for future
implementations.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To help prevent plane state not being set to the correct default
value if any new properties are added in the future.
[How]
Use the drm helper - which seems to be the common solution among other
DRM drivers.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
we were only checking the return value in one place, thus changing
generic_reg_wait from int to void and reading the register instead of
getting it from generic_reg_wait, when we need the return value.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The plane_reset callback is subclassed but hasn't been updated since
the drm helper got updated to include resetting alpha related state
(state->alpha and state->pixel_blend_mode). The overlay planes
exposed by amdgpu_dm were therefore being rendered as invisible by
default ever since supported was exposed for alpha blending properties
on overlays.
This caused regressions in igt@kms_plane_multiple@atomic-tiling-none
and igt@kms_plane@plane-position-covered-pipe tests.
[How]
Reset the plane state values to their correct values as defined in
the drm helper.
This fixes the IGT test regression.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect hardcoded assumptions are made regarding luma and chroma
alignment. The actual values set for the DRM framebuffer should be used
when programming the address.
[How]
Respect the given pitch for both luma and chroma planes - it's not like
we can force the alignment to anything else at this point anyway.
Use the FB offset for the chroma planes directly. DRM already
provides this to us so there's no need to calculate it manually.
While we don't actually use the chroma surface size parameters on Raven,
these should have technically been fb->width / 2 and fb->height / 2
since the chroma plane is half size of the luma plane for NV12.
Leave a TODO indicating that those should be set based on the actual
surface format instead since this is only correct for YUV420 formats.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For new DC planes the correct plane address fields are filled based
on whether the plane had a graphics or video format.
However, when we perform stream and plane updates using DC we only ever
fill in the graphics format fields. This causing corruption and hangs
when using video surface formats like NV12 for planes.
[How]
Use the same logic everywhere we update dc_plane_address - always
fill in the correct fields based on the surface format type.
There are 3 places this is done:
- Atomic check, during DC plane creation
- Atomic commit, during plane prepare_fb
- Atomic commit tail, during amdgpu_dm_commit_planes
We use the fill_plane_tiling_attributes in all 3 locations and it
already needs the address to update DCC attributes, so the surface
address update logic can be moved into this helper.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor updates must acquire the pipe control lock to
prevent vupdate from triggering in the middle of cursor
programming. On DCN1 the pipe control lock prevents
pageflips from occurring. This means that a cursor update
right before vupdate can delay a pending pageflip
[How]
If the time until the next vupdate is less than a
conservative estimate of the cursor programming time,
wait until the vupdate has passed before locking.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We will not retry when EDID read failure using i2c over aux
[how]
treat i2c over aux failure the same as defer
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
"reference clock" is a very overloaded variable in DC and causes confusion
as there are multiple sources of reference clock, which may be different values
incorrect input values to DML will cause DCHUB to be programmed improperly
and lead to hard to debug underflow issues
[how]
instead of using ref clock everywhere, specify WHICH ref clock:
- xtalin
- dccg refclk
- dchub refclk
these are all distinct values which may not be equal
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DRM overlay planes DM exposes support RGBA formats but are currently
forced as fully opaque over whatever they overlay.
[How]
Expose DRM blending mode and alpha properties to userspace.
The overlays exposed support per-pixel pre-multiplied alpha along with
global plane opacity.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Actual breakdown of DPM level varies by SKU (for the same family)
DC needs some ability to ammend pre-silicon numbers
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Increased power savings are desired for ABM 2.2.
[How]
Reduce the minimum reduction level, the deviation gain and the contrast factor
to allow for more aggressive operation of the algorithm.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HDMI has TMDS and FRL signal types. Be specific about what is used.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Stream update will adjust both info packets and stream params,
need to make sure all things are applied togather.
[how]
add pipe lock during stream update
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
At 24 Hz, a frame is 41.7 ms, so a 30 ms wait can (and does often)
timeout.
[How]
Bump timeout from 30 ms to 50 ms.
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
field toggle write is actual field sequence write with the same
field name.
[How]
Use REG_UPDATE_SEQ_2 for both sequence write and toggle.
Rename REG_UPDATE_1by1_3 to REG_UPDATE_SEQ_3.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We have new bios capabilities enabling s0i2 entry on SMU interrupt. We want
this interrupt to be fired on PSR transitions such that we enter s0i2
when entering PSR active.
[HOW]
Add code to send the SMU interrupt with the appropriate
staticscreen flag when entering and exting PSR. Protect this
code with a config flag since it currently impacts BL PWM.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current reg update and reg set use same functions and
only delta is update reads reg value and call update function.
[How]
Refactor reg update and reg set functions.
1.Implement different functions for reg update and reg set.
2.Wrap same process to a help function, both reg update and
reg set will call it.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cross a TODO item off the list. Cleanup SIGNAL_TYPE_HDMI_FRL, it's
not currently supported.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Get rid of DV style dml init in favour of the cleaner DC
style.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Can happen on ASICs with 6 planes, but this isn't a bug since we haven't
written outside the array.
[How]
Use <= instead of <.
Cc: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reported-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
New DRM versions manage locking for private objects for us, so this
is no longer needed.
This also prevents a WARN_ON from occurring when the private object is
duplicated during the forced atomic commit that occurs from the HPD
handler.
The HPD handler calls drm_modeset_lock_all before the forced commit
and if the private object is duplicated then the
DEBUG_LOCKS_WARN_ON(ww_ctx->done_acquire) warning will be triggered
since we're trying to lock something when everything should have
already been locked.
[How]
Drop the lock and let DRM manage this.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we get any values equal to 0, and set to 1 if so.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
res_pool->pp_smu may be NULL. Check before use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
AUX transaction returns success, but data has invalid lane count and rate
which when passed to VBIOS command table causes it to soft hang
[How]
Do some sanity checking and fail if the DPCD caps are invalid.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Tiling and DCC attributes can change when swapping framebuffers but
these will only ever get updated on full commits where
state->allow_modeset is true. But for the page-flip IOCTL
state->allow_modeset = false so these aren't updated and DCC changes
aren't being programmed.
[How]
Split out updating the tiling and DCC attributes into its own function
that's called when creating the plane for the first time but also
called when switching framebuffers before commit stream updates.
These functions also don't modify the plane state directly since the
plane state being used as reference is often the current one
being used by the hardware.
DC needs to be able to compare plane_state to the stream update
structures to determine if the hardware programming should happen. If
it's modified in place then nothing will be programmed and we can run
into concurrency issues.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The dc_gamma_type CUSTOM_GAMMA is used to represent degamma
mappings passed in by drm. This type of gamma must be interpolated
into a transfer function by apply_1d_lut. The line in
mod_color_calculate_degamma_params that handled this case
was erroneously removed.
[How]
For CUSTOM_GAMMA degamma, calculate the lut as before.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 6bff1cc7780cca2fd2a775aa7b18b789e2a1b608.
[Description]
Revert since this will be checked at CP side.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
used to be unable to run 4:2:0 if using a dongle because 4k60 bandwidth
exceeded dongle caps
[How]
half pixel clock during comparison to dongle cap. *Could get stuck on black
screen on monitor that don't support 420 but will be selecting 420 as
preferred mode*
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Aidan Wood <Aidan.Wood@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
UEFI boot usually uses a boot profile that uses higher clocks
and watermark settings.
UEFI boot surface is less optimal, for example it uses linear surface
[How]
Before we finish our seamless boot sequence, keep the clock and
watermark settings from boot.
Update to optimal settings only after first flip away from UEFI
frame buffer.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
commit_planes is indented quite far
[How]
Move the pageflip code from an if statement to after a
continue
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IGT expects that pageflips can be triggered with the same
framebuffer before and after the commit
[How]
Expand the definition of pageflip to include any change
with an old framebuffer and a new framebuffer, even if they're
the same
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Raven has support for combining pipes for DRM_PLANE_TYPE_OVERLAY use
but no overlays are exposed to userspace.
[How]
Expose overlay planes based on DC plane caps.
If all the pipes are in use then the atomic commits can fail, but this
is expected behavior for userspace.
Only support RGB on overlays for now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Primary and underlay planes were previously exposed to DRM by using
max_planes and max_slave_planes.
The value for max_planes was always pipe_count + has_underlay.
If there was an underlay pipe, then max_slave_planes = 1.
Raven has pipe_count = 4, max_planes = 4, and max_slave_planes = 1.
So during plane initialziation it was actually "creating"
1 overlay plane and 3 primary planes... or it would be, had its
plane_type array not been dm_plane_type_default, which will only create
DRM_PLANE_TYPE_PRIMARY planes.
We can expose primary planes as supporting more than one CRTC at a time
to more closely resemble plane behavior on DCN but userspace doesn't
really expect planes to be used in this manner and will either
ignore the planes or crash.
Planes with index greater than max_streams are marked as supporting
all CRTCs. No ASIC currently has primary plane count greater than the
stream count but we shouldn't expose more than necessary.
[How]
Drop support for underlay planes. They aren't well tested and don't
fully work right at the moment.
Only create one primary plane per CRTC so we're not creating overlays.
Initialize plane types directly instead of referencing a misleading
array of plane types.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The current dc_caps doesn't provide the information needed to
determine the count and type of each plane to be exposed to userspace.
There are three types of DRM planes that are exposed to userspace:
1. Primary planes (can be used for modesetting)
2. Overlay planes (can be blended below or above a primary plane)
3. Cursor planes (blended topmost)
We need to know the number and type of each in amdgpu_dm to expose
to userspace.
Hardware supports blending planes below, above or both ways depending
on the ASIC. Alpha support is also ASIC dependent. Some hardware has
dedicated pipes for overlays and other hardware combines the pipes.
All of this should be exposed in a way that DM can query and use.
[How]
Introduce the dc_plane_cap structure that describes the capabilities
for the hw planes.
It describes:
- the type of the plane
- whether the plane can blend with planes below it
- whether the plane can blend with planes above it
- whether the plane supports per pixel alpha blending
- supported formats on the plane (partial list for now)
Pre DCN ASICs don't have their full capabilities described for now.
They can be updated as needed in the future.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The kms_plane@plane-position-covered-pipe-*-planes subtests can produce
a sequence of atomic commits such that neither active_changed nor
mode_changed but connectors_changed.
When this happens we remove the old stream from the context and add
a new stream but the new stream doesn't have mode_changed=true set.
This incorrect programming sequence causes CRC mismatches to occur in
the test.
The stream->mode_changed value should be set whenever a new stream
is created.
[How]
A new stream is created whenever drm_atomic_crtc_needs_modeset is true.
We previously covered the active_changed and mode_changed conditions
for the CRTC but connectors_changed is also checked within
drm_atomic_crtc_needs_modeset.
So just use drm_atomic_crtc_needs_modeset directly to determine the
mode_changed flag.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new aux implementation was not up to spec. This caused us to fail DP
compliance as well as introduced serious delays during system resume.
[How]
Make dce_aux_transfer_raw return the operation result
Make dce_aux_transfer_with_retries delay with udelay instead
of msleep, and only on invalid reply. Also fail on the second
invalid reply, third timeout, or first of any other error
Convert return values to drm error codes in amdgpu_dm
As the two aux transfer functions are now noticeably
different, change the names to better reflect their
functionality and document.
There was one last call to dc_link_aux_transfer that
should have retries, fix that
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In some cases we might need to do a full update. Add a commit_hints
struct for future use
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With special monitor combination on MST, the UP_REQ could come
after clear payload table. It makes the pending DOWN_REP fail
to be handled after link training and the new DOWN_REQ will be queued
until time out .
[How]
To move the current polling pending DOWN_REP procedure to after
clear payload table to make sure the pending DOWN_REP can be
done before enabling the link.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch implements inteferface to set watermarks table for clock ranges on
smu 11. It fills watermark table before it is written to SMC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds interface to notify smu enable pme restore register for display
and in smu v11 didn't have this implementation.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fills the amd_pp_clock_info data for display, it will get the current
info in that structure.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds interface to request display clock voltage, display will use it
to request current display clock voltage.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds inteface to get clock by type with voltage, display will use it
to get current clocks with voltage.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds get clock by type with latency, display will use it to get
current clocks with latency.
v2: fix the missed mutex lock before return.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds interface to get max high clocks for display and in smu v11
didn't have this implementation.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds get_clock_by_type interface for display, in smu v11 didn't have
the implementation.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds display configuration change function that creates the new path
with sw smu driver instead of powerplay.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Powerplay functions called from dm_pp_* functions tend to do a
mutex_lock which isn't safe to do inside a kernel_fpu_begin/end block as
those will disable/enable preemption.
Rearrange the dm_pp_get_clock_levels_by_type_with_voltage calls to make
sure they happen outside of kernel_fpu_begin/end.
Cc: stable@vger.kernel.org
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark McGarrity <mark.mcgarrity@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a dc_bounding_box_overrides struct to define bb overrides. It is
loaded in during DC init.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_commit_updates_for_stream is called twice per stream: once
with the flip data and once will all other data. This causes
problems when these DC calls have different numbers of planes
For example, a commit with a pageflip on plane A and a
non-pageflip change on plane B will first call
into DC with just plane A, causing plane B to be
disabled. Then it will call into DC with both planes,
re-enabling plane B
[How]
Merge flip and full into a single bundle
Apart from the single DC call, the logic should not be
changed by this patch
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP v1.4 allows panels to report link rates other than RBR/HBR/HBR2, that
may be more optimal for the panel's timing. Power can be saved by using
a link rate closer to the required bandwidth of the panel's timing.
[How]
Scan the table of reported link rates from the panel, and select the
minimum link rate that satisfies the bandwidth requirements of the panel's
timing. Include a flag to make the feature optional.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Will be used to signify if P-state change is supported.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The wait_for_vblank boolean in commit_tail was passed by reference
into each stream commit, and if that commit was an asynchronous
flip, it would disable vblank waits on all subsequent flips.
This made the behaviour depend on crtc order in a non-intuitive way,
although since the asynchronous pageflip flag is only used by the
legacy IOCTLs at the moment it is never an issue
[How]
Find wait_for_vblank before doing any stream commits
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When doing split pipe, if one pipe is pending on flip, the entire
plane's status should be flip pending, otherwise corruption can occur
when OS writes to a surface prematurely.
[HOW]
Clear the flip pending bit before checking pipes, then OR the flip
pending bits from all pipes together to create the flip pending status
of the entire plane.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <Eryk.Brol@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
AUX arbitration occurs between SW and FW components.
When AUX acquire fails, it causes engine->ddc to be NULL,
which leads to an exception when we try to release the AUX
engine.
[How]
When AUX engine acquire fails, it should return from the
function without trying to continue the operation.
The upper level will determine if it wants to retry.
i.e. dce_aux_transfer_with_retries will be used and retry.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot tries to reuse planes that were enabled for the first
commit applied.
In the case where Raven is booting with two monitors connected and the
first commit contains two streams the screen corruption would occur
because the second stream was trying to re-use a tg and plane that
weren't previously enabled.
The state on the first commit looks something like the following:
TG0: enabled=1
TG1: enabled=0
TG2: enabled=0
TG3: enabled=0
New state: pipe=0, stream=0, plane=0, new_tg=0
New state: pipe=1, stream=1, plane=1, new_tg=1
New state: pipe=2, stream=NULL, plane=NULL, new_tg=NULL
New state: pipe=3, stream=NULL, plane=NULL, new_tg=NULL
Only one plane/tg is setup before we enter accelerated mode so
we really want to disabling everything but that first plane.
[How]
Check if the stream is not NULL and if the tg is enabled before
deciding whether to skip the plane disable.
Also ensure we're also disabling on the current state's pipe_ctx so
we don't overwrite the fields in the new pending state.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change changes dc add plane logic to allow plane-less resource
reservation (pipe split).
If a free pipe_ctx (no plane_state attached) is the head pipe, and is
found with a bottom pipe attached, assign the plane to add on the bottom
pipe.
In addition, prepend dcn10 to dcn10-specific reset_back_end_for_pipe
and reset_hw_ctx_wrap
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver need to poll the SURFACE_INUSE register to determine when to
start the new task and write data to the checked surface.
Implement the wait functions, and add the necessary hubbub registers.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For later use by the DC VM implementation
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot code not working on all ASICs because of
some underflow issues caused by some uninitialized HW
state.
[How]
Keep some logical and power gating init code in hw_init.
Move some per pipe init code to enable accelerated mode
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM has impelemented new pp_smu interface. 'Else' is not longer needed.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Yongqiang Sun <yongqiang.sun@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This enum definition is shared, so move it to a shared location.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: mmcgarri <mark.mcgarrity@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make dml and integration with pplib clearer.
[How]
Change the way the dml formula is initialized to make its values more
clear. Restructure DC interface with pplib into rv_funcs.
Cap clocks received from pplib.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Added a "disable_tri_buf" DC debug option. When set to 1 feature will
be off.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In VRR mode, keep track of the vblank count of the last
completed pageflip in amdgpu_crtc->last_flip_vblank, as
recorded in the pageflip completion handler after each
completed flip.
Use that count to prevent mmio programming a new pageflip
within the same vblank in which the last pageflip completed,
iow. to throttle pageflips to at most one flip per video
frame, while at the same time allowing to request a flip
not only before start of vblank, but also anywhere within
vblank.
The old logic did the same, and made sense for regular fixed
refresh rate flipping, but in vrr mode it prevents requesting
a flip anywhere inside the possibly huge vblank, thereby
reducing framerate in vrr mode instead of improving it, by
delaying a slightly delayed flip requests up to a maximum
vblank duration + 1 scanout duration. This would limit VRR
usefulness to only help applications with a very high GPU
demand, which can submit the flip request before start of
vblank, but then have to wait long for fences to complete.
With this method a flip can be both requested and - after
fences have completed - executed, ie. it doesn't matter if
the request (amdgpu_dm_do_flip()) gets delayed until deep
into the extended vblank due to cpu execution delays. This
also allows clients which want to regulate framerate within
the vrr range a much more fine-grained control of flip timing,
a feature that might be useful for video playback, and is
very useful for neuroscience/vision research applications.
In regular non-VRR mode, retain the old flip submission
behavior. This to keep flip scheduling for fullscreen X11/GLX
OpenGL clients intact, if they use the GLX_OML_sync_control
extensions glXSwapBufferMscOML(, ..., target_msc,...) function
with a specific target_msc target vblank count.
glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will
not flip at the proper target_msc for a non-zero target_msc
if VRR mode is active with this patch. They'd often flip one
frame too early. However, this limitation should not matter
much in VRR mode, as scheduling based on vblank counts is
pretty futile/unusable under variable refresh duration
anyway, so no real extra harm is done.
According to some testing already done with this patch by
Nicholas on top of my tests, IGT tests didn't report any
problems. If fixes stuttering and flickering when flipping
at rates below the minimum vrr refresh rate.
Fixes: bb47de7366 ("drm/amdgpu: Set FreeSync state using drm VRR
properties")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Tested-by: Bruno Filipe <bmilreu@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In VRR mode, keep track of the vblank count of the last
completed pageflip in amdgpu_crtc->last_flip_vblank, as
recorded in the pageflip completion handler after each
completed flip.
Use that count to prevent mmio programming a new pageflip
within the same vblank in which the last pageflip completed,
iow. to throttle pageflips to at most one flip per video
frame, while at the same time allowing to request a flip
not only before start of vblank, but also anywhere within
vblank.
The old logic did the same, and made sense for regular fixed
refresh rate flipping, but in vrr mode it prevents requesting
a flip anywhere inside the possibly huge vblank, thereby
reducing framerate in vrr mode instead of improving it, by
delaying a slightly delayed flip requests up to a maximum
vblank duration + 1 scanout duration. This would limit VRR
usefulness to only help applications with a very high GPU
demand, which can submit the flip request before start of
vblank, but then have to wait long for fences to complete.
With this method a flip can be both requested and - after
fences have completed - executed, ie. it doesn't matter if
the request (amdgpu_dm_do_flip()) gets delayed until deep
into the extended vblank due to cpu execution delays. This
also allows clients which want to regulate framerate within
the vrr range a much more fine-grained control of flip timing,
a feature that might be useful for video playback, and is
very useful for neuroscience/vision research applications.
In regular non-VRR mode, retain the old flip submission
behavior. This to keep flip scheduling for fullscreen X11/GLX
OpenGL clients intact, if they use the GLX_OML_sync_control
extensions glXSwapBufferMscOML(, ..., target_msc,...) function
with a specific target_msc target vblank count.
glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will
not flip at the proper target_msc for a non-zero target_msc
if VRR mode is active with this patch. They'd often flip one
frame too early. However, this limitation should not matter
much in VRR mode, as scheduling based on vblank counts is
pretty futile/unusable under variable refresh duration
anyway, so no real extra harm is done.
According to some testing already done with this patch by
Nicholas on top of my tests, IGT tests didn't report any
problems. If fixes stuttering and flickering when flipping
at rates below the minimum vrr refresh rate.
Fixes: bb47de7366 ("drm/amdgpu: Set FreeSync state using drm VRR
properties")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Tested-by: Bruno Filipe <bmilreu@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlx8YYIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGs5MIAIiVVIH+C0St60vf
nzfGpVe+BETe199UveM4Ic2FWMk97ZhSk5Oj6HwYY9vnw4iwoRCZIO5B8Dna4nxY
8XjiwxpJRVLq+7Y1d61O6NHo6UjFHF0GMzyeJeNNUq+mCISxZdLsqzsszt9X09mA
GoJjZ0UMw2Tkz/s3Ie4MumKASc+y2CjJc0ZVEZlJsMaqMJLIfUn/CrTzHBivmuqJ
sV6ZkP4as6h87bI9mi79p8pzvVooCRJ10cg4A/DHG4t2bEAIlB4t5dfZRFzVMhVo
cCPRk9tiA9y4I3zBjcuAZMODcBpfdWoQK8TqYw2cDS3LEDMgnEdIH6snMYHr69z0
kZJjA2A=
=Qs0l
-----END PGP SIGNATURE-----
Merge v5.0 into drm-next
There is a really hairy resolution involving amdgpu fixes, that I'd rather confirm here.
Also some misc fixes are landed by me, but the pr has them as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Clang warns when an expression that equals zero is used as a null
pointer constant (in lieu of NULL):
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:4435:3:
warning: expression which evaluates to zero treated as a null pointer
constant of type 'const enum color_transfer_func *'
[-Wnon-literal-null-conversion]
TRANSFER_FUNC_UNKNOWN,
^~~~~~~~~~~~~~~~~~~~~
1 warning generated.
This warning is caused by commit bb47de7366 ("drm/amdgpu: Set FreeSync
state using drm VRR properties") and it could be solved by using NULL
instead of TRANSFER_FUNC_UNKNOWN or casting TRANSFER_FUNC_UNKNOWN as a
pointer. However, after looking into it, there doesn't appear to be a
good reason to pass app_tf by reference as it is never mutated along the
way. This is the only code path in which app_tf is used:
mod_freesync_build_vrr_infopacket ->
build_vrr_infopacket_v2 ->
build_vrr_infopacket_fs2_data
Neither mod_freesync_build_vrr_infopacket or build_vrr_infopacket_v2
modify app_tf's value and build_vrr_infopacket_fs2_data expects just
the value so we can avoid dereferencing anything by just passing in
app_tf's value to mod_freesync_build_vrr_infopacket and
build_vrr_infopacket_v2.
There is no functional change because build_vrr_infopacket_fs2_data
doesn't do anything if TRANSFER_FUNC_UNKNOWN is passed to it, the same
as not calling build_vrr_infopacket_fs2_data at all like before this
change when NULL was used for app_tf.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For MST, link not disabled until all streams disabled
[How]
Add check for stream_count before setting link_active = false for MST
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In VRR mode, keep track of the vblank count of the last
completed pageflip in amdgpu_crtc->last_flip_vblank, as
recorded in the pageflip completion handler after each
completed flip.
Use that count to prevent mmio programming a new pageflip
within the same vblank in which the last pageflip completed,
iow. to throttle pageflips to at most one flip per video
frame, while at the same time allowing to request a flip
not only before start of vblank, but also anywhere within
vblank.
The old logic did the same, and made sense for regular fixed
refresh rate flipping, but in vrr mode it prevents requesting
a flip anywhere inside the possibly huge vblank, thereby
reducing framerate in vrr mode instead of improving it, by
delaying a slightly delayed flip requests up to a maximum
vblank duration + 1 scanout duration. This would limit VRR
usefulness to only help applications with a very high GPU
demand, which can submit the flip request before start of
vblank, but then have to wait long for fences to complete.
With this method a flip can be both requested and - after
fences have completed - executed, ie. it doesn't matter if
the request (amdgpu_dm_do_flip()) gets delayed until deep
into the extended vblank due to cpu execution delays. This
also allows clients which want to regulate framerate within
the vrr range a much more fine-grained control of flip timing,
a feature that might be useful for video playback, and is
very useful for neuroscience/vision research applications.
In regular non-VRR mode, retain the old flip submission
behavior. This to keep flip scheduling for fullscreen X11/GLX
OpenGL clients intact, if they use the GLX_OML_sync_control
extensions glXSwapBufferMscOML(, ..., target_msc,...) function
with a specific target_msc target vblank count.
glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will
not flip at the proper target_msc for a non-zero target_msc
if VRR mode is active with this patch. They'd often flip one
frame too early. However, this limitation should not matter
much in VRR mode, as scheduling based on vblank counts is
pretty futile/unusable under variable refresh duration
anyway, so no real extra harm is done.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes for 5.1:
amdgpu:
- Fix missing fw declaration after dropping old CI DPM code
- Fix debugfs access to registers beyond the MMIO bar size
- Fix context priority handling
- Add missing license on some new files
- Various cleanups and bug fixes
radeon:
- Fix missing break in CS parser for evergreen
- Various cleanups and bug fixes
sched:
- Fix entities with 0 run queues
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221214134.3308-1-alexander.deucher@amd.com
[Why]
When a dce80 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
optimize_bandwidth was using dce100_prepare_bandwidth this is incorrect
[How]
change it to dce100_optimize_bandwidth
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current periodic interrupt start point calc in optc
is not clear.
[How]
1. DM convert delta time to lines number and dc will calculate the
start position as per lines number and interrupt type.
2. hwss calculates the start point as per line offset.
3. optc programs vertical interrupts register as per start point
and interrupt source.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The stream->mode_changed flag can persist in the following sequence
of atomic commits:
Commit 1:
Enable CRTC0 (mode_changed = true), Enable CRTC1 (mode_changed = true)
Commit 2:
Disable CRTC1 (mode_changed = false)
In this sequence we want to keep the exiting CRTC0 but it's not in the
atomic state for the commit since it hasn't been modified. In this case
the stream->mode_changed flag persists as true and we don't re-program
the planes for the existing stream.
[How]
The flag needs to be cleared and it makes the most sense to do it within
DC after the state has been committed. Nothing following dc_commit_state
should think that the stream's mode has changed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor updates used to happen after vblank/flip/stream updates before
the stream update refactor. They now happen before stream updates
which means that they're not going to be synced with fb changes
and that they're going to programmed for pipes that we're disabling
within the same commit.
[How]
Move them after stream updates.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever a stream or plane is added or removed from the context the
pointer will change from old to new. We set lock and validation
needed in these cases. But not all of these cases match update_type
from dm_determine_update_type_for_commit - an example being overlay
plane updates.
There are warnings for a few of these cases that should be fixed.
[How]
We can closer align to DC (and lock_and_validation_needed) by
comparing stream and plane pointers.
Since the old stream/old plane state is never freed until sometime
after the commit tail work finishes we are guaranteed to never get
back the same block of memory when we remove and create a stream or
plane state in the same commit.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This format isn't supported in DC and some IGT tests fail since we
expose support for it.
[How]
Remove it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If a commit updates an overlay plane via the legacy plane IOCTL
then the only plane in the state will be the overlay plane.
Overlay planes need to be added first to the DC context, but in the
scenario above the plane will be added last. This will result in wrong
z-order during rendering.
[How]
If any non-cursor plane has been updated then the rest of the
non-cursor planes should be added to the CRTC state.
The cursor plane doesn't need to be included for stream updates and
locking it will cause performance issues. It should be ignored.
DC requires that the surface count passed during stream updates
be the number of surfaces currently on the stream to enable fast
updates. This previously wasn't the case without this patch, so this
also allows this optimization to occur.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously, a change removed code that would send a pipe set command
to dmcu each time the backlight was set, as it was thought to be
superfluous. However, it is possible for the backlight to be set
before a valid pipe has been set, which causes DMCU to hang after a
DPMS restore on some systems.
[How]
Send a pipe set command to DMCU prior to setting the backlight.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain tests fail after a fresh reboot. This is caused by writing to
registers prior to ungating the stream we're trying to program.
[How]
Make sure the stream is ungated before writing to its registers.
This also enables power-gating plane resources before init_hw
initializes them.
Additionally, this does some refactoring to move gating/ungating
from enable/disable_plane functions to where stream resources are
enabled/disabled.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We are currently losing precision when we convert from
16 bit --> 8 bit --> 16 bit.
[How]
We shouldn't down convert unnecessarily and lose precision.
Keep values at 16 bit and use directly.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want boot to desktop to be seamless
[How]
During init pipes, avoid touching the pipes where GOP has already
enabled the HW to the state we want.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When stream is blanked, pipe set command is sent to dmcu to notify it
that the abm pipe is disabled. When stream is unblanked, no notification is
made to dmcu that the abm pipe has been enabled, resulting in abm not
being enabled in the firmware.
[How]
When stream is unblanked, send a pipe set command to dmcu.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual corruption due to low display clock value.
Observed on Carrizo 4K@60Hz.
[How]
There was earlier patch for dce_update_clocks:
Adding +15% workaround also to to dce11_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm_dp_mst_topology_mgr_suspend() is added into the new reboot
sequence, which disables the UP request at the beginning.
Therefore sideband messages are blocked.
[How]
Finish MST sideband message transaction before UP request is
suppressed.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge v5.0-rc7 into drm-next
Backmerging for nouveau and imx that needed some fixes for next pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
When ring hang happens amdgpu_dm_commit_planes during flip is holding
the BO reserved and then stack waiting for fences to signal in
reservation_object_wait_timeout_rcu (which won't signal because there
was a hnag). Then when we try to shutdown display block during reset
recovery from drm_atomic_helper_suspend we also try to reserve the BO
from dm_plane_helper_cleanup_fb ending in deadlock.
Also remove useless WARN_ON
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's useful to know the min and max vrr range for IGT testing.
[How]
Expose the min and max vfreq for the connector via a debugfs file
on the connector, "vrr_range".
Example usage: cat /sys/kernel/debug/dri/0/DP-1/vrr_range
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dal_gpio_open and dal_gpio_unlock_pin dereference hpd_gpio.
Check for NULL before calling those functions.
Fixes: ac627caf6b ("drm/amd/display: add gpio lock/unlock")
Reported-by: Przemek Socha <soprwa@gmail.com>
CC: Chiawen Huang <chiawen.huang@amd.com>
CC: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pipe related init is possible to optimized if we know what we
intend to program, and if we can determine it matches what is
already programmed for the pipe.
[How]
First step is to isolate the pipe related init code
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Keep enable_stream_timing programming only
timing related stuff.
[How]
Move DRR and static screen mask programming from
enable_stream_timing to outside in
apply_single_controller_ctx_to_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we determine the stream we are trying to commit
matches HW, we want to try to optimize.
[How]
Try to acquire the HW resources that are already enabled
and optimize.
Also skip backend reprogramming
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to understand whether link is active aside from stream state.
This could be used to check what links are enabled by GOP.
[How]
Store link_active state in link status and initialize it by checking
if the DIG is enabled.
Keep it updated on every link enable and disable
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
More clearly isolate the code that is involved in programming of
vupdate interrupt
[How]
Add function for programming of vupdate interrupt.
Call it after timing is programmed.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to figure out whether a timing we want to commit matches
something that GOP already programmed, in which case
we can decide to some optimizations
[How]
1. Add way to check for DIG FE
2. Add way to check for matching OTG timing
3. Add way to check for matching pixel clock (if possible)
- Currently only support DP for pixel clock, since it is easy to calc
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When moving mouse onto or off of pip plane,
screen would flash briefly due to garbage negative
pos values being programmed for cursor.
Also, text flashes due to PIP flips taking too long.
[How]
When negative pos value seen, default to 0 and adjust by modifying cursor hotspot.
For flip issue, only do post update when optimize required vs all the time.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current implementation that maps link_rate_set value to
actual link rate is incorrect.
[How]
Fix this implementation, such that link_rate_set indexes into
the supported_link_rate table.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VM_helper needs to be intialized with the dc struct in order to fix
an unallocated memory issue. System aperture settings should be
initialized to 0 and guarded with a check to make sure vm_config
is valid.
[How]
Allocate and free memory for vm_helper with other dc members.
Check whether the vm_config valid bit is set before initializing
aperture settings.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Bandwidth calculation formulas currently do not take Stereo 3D + Stutter
properly into account. Disable stutter feature when we detect a Stereo
3D mode as a temporary workaround.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to calcualte vline position in DC for DCN.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The dc_sink was released but the pointer on the aconnector was
not cleared.
[How]
Clear it.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are opt1c lock warnings and CRTC read timeouts when running the
"igt@kms_plane@plane-position-hole-dpms-pipe-*" tests. These are
caused by trying to reprogram planes that are not in the current
context.
DPMS off removes the stream from the context. In this case:
new_crtc_state->active_changed = true
new_crtc_state->mode_changed = false
The planes are reprogrammed before the stream is removed from the
context because stream_state->mode_changed = false.
For DPMS adds the stream and planes back to the context:
new_crtc_state->active_changed = true
new_crtc_state->mode_changed = false
The planes are also reprogrammed here before the stream is added to the
context because stream_state->mode_changed = true. They were not
previously in the current context so warnings occur here.
[How]
Set stream_state->mode_changed = true when
new_crtc_state->active_changed = true too.
This prevents reprogramming before the context is applied in DC. The
programming will be done after the context is applied.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove extraneous parentheses around the comparison
to silence this warning
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This fixes an mpc programming error for the following sequence of
atomic commits when pipe split is enabled:
Commit 1: CRTC0 (plane 4, plane 3)
Pipe 0: old_plane_state = A0, new_plane_state = A1, new_tg = T0
Pipe 1: old_plane_state = B0, new_plane_state = B1, new_tg = T0
Pipe 2: old_plane_state = A0, new_plane_state = A1, new_tg = T0
Pipe 3: old_plane_state = B0, new_plane_state = B1, new_tg = T0
Commit 2: CRTC0 (plane 3), CRTC1 (plane 2)
Pipe 0: old_plane_state = A1, new_plane_state = A2, new_tg = T0
Pipe 1: old_plane_state = B1, new_plane_state = B2, new_tg = T1
Pipe 2: old_plane_state = A1, new_plane_state = NULL, new_tg = NULL
Pipe 3: old_plane_state = B1, new_plane_state = NULL, new_tg = NULL
In the second commit the assertion for mpcc in use is hit because
mpcc disconnect never occurs for pipe 1. This is because the stream
changes for pipe 1 and the opp_list is empty.
This sequence occurs when running the
"igt@kms_plane_multiple@atomic-pipe-A-tiling-none" test with two
displays connected.
[How]
Expand the reset condition to include:
"old_pipe_ctx->stream_res.tg != new_pipe_ctx->stream_res.tg"
...but only when the plane state is non-NULL for both old and new.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It fixes the failure to create stream for sink in the scenario
when hotplug SST and MST in sequence, and disconnect MST.
[How]
Add the fake sink back after the majority of MST rework is done.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding a bit vector to allow forcing odm on specific otgs
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
in program_timing_sync, after all the pipes are
grouped, store timing sync info in dc_stream_status
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reduced backlight for ABM 2.2 at levels 1 and 2 is desired for
power savings.
[How]
Reduce the max reduction parameters for ABM 2.2
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When querying HPD via GPIO flow,
it will create a new gpio object then free in the end of query.
There is a irql issue for HPD querying at ISR level.
[How]
Therefore, creating the HPD gpio object in dc_link and set it as unlcok in default.
1. reducing unnecessary malloc/free when HPD querying.
2. reducing init GPIO flow.
3. add lock/unlock to prevent multi gpio service running.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
is_blanked is not a general indicator of if a pipe is synced
for all asics.
plane state is more accurate and applicable for all asics.
[how]
Remove is_blanked call and
add checking plane_state against NULL instead.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On HW that doesn't have input LUT, we may combine degamma with OS ramp
Problem here is that it assumes DGAM is inverse of PQ or SRGB. It doesn't
handle linear case, it would default to sRGB and always enable DGAM..
[How] Add handling for linear case. Also check for null ramp and instead of
blowing up, assume it's identity.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Setting monitor refresh rate below freesync range would cause the
monitor to go blank indefinitely with freesync enabled
[How]
Set vrr_supported and ignore_msa_timing_param according to whether
the refresh rate is above or below the minimum freesync frequency.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Second screen to clone/extend mode, driver will send ABM pipe
command to DMCU. Change mode from clone/extend to second
screen only, driver send ABM level command to disable ABM but
this command will not clear ABM pipe data. At this time, change
second screen to PC screen only, driver will send first command
"ABM_LEVEL", it will turn on ABM with incorrect ABM pile so that
DMCU is blocking.
[How]
When driver try to disable ABM, change command from "ABM LEVEL"
to "ABM PIPE" so that it will clear ABM pile data.
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The problem is that we accidentally stopped loading some of the IRAM bytes
used for the backlight ramping mechanism. This happened when we
started reserving some region of IRAM as DMCU FW write only.
[How]
This change will define a start+end region for the IRAM read only region.
So the parameters needed for the backlight operation will be loaded
since it will be defined outside of the read only region.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Different panel need different time from backlight disable to end of valid video data,
if the time is too short, panel will flash when dpms off
[How]
Add monitor patch to control the time from backlight disable to end of valid video data,
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This provides little debug value and creates a lot of dmesg noise.
[How]
Remove it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The stream_update struct is left unitialized but DC will access
its fields. This usually results in global state validation occur
during any atomic commit with state->allow_modeset = true.
[How]
Initialize the struct to zero for every stream we check.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The indenting for this function is a few levels too deep and can be
simplified a fair bit. This patch is in preparation for functional
changes that fix update type determination to occur less frequently
and more accurately.
[How]
Place checks early and exit/continue when possible. This isn't
a functional change.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We were always passing the first surface on the stream status for
flip updates when we should be using the surface associated with
the plane.
[How]
Use the dc_plane_state from the plane that's being updated.
FreeSync should also only keep track of updates from the primary
plane, so the check needed to be updated.
The acrtc->stream state doesn't need to be checked for NULL before
updating FreeSync either since there needs to be a stream to be
inside this function as a prerequisite.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Most surface updates weren't propagated onto the surface during
dc_commit_updates_for_stream. This makes it more difficult for DC to
determine the actual surface update type required.
[How]
Use copy_surface_update_to_plane to propagate the changes. The FreeSync
surface timing information update for BTR has been moved out of
amdgpu_dm.c into this function as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
"IRQ_HPD Pulse Length Test" DP compliance test
fails. Test complains that certain DPCD registers
are not read within 100 ms.
[How]
msleep is inaccurate for small values. Used udelay
instead for accuracy.
Signed-off-by: John Barberiz <John.Barberiz@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
FBC fails to get enabled when switched between LINEAR(console/VT)
and non-LINEAR(GUI) based rendering due to default value of
tiling info stored in the current_state which is used for deciding
whether or not to turn FBC on or off.
[How]
Use context structure's tiling information which is coherant with
the screen updates.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When CONFIG_DEBUG_FS isn't defined then amdgpu_dm_crtc_set_crc_source
is NULL. This causes a compilation error since it's being called
unconditionally.
[How]
Guard the call based on CONFIG_DEBUG_FS - CRC capture isn't supported
without this.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Fixes: 43a6a02eb3 ("drm/amd/display: Re-enable CRC capture following modeset")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:2314:38:
warning: suggest braces around initialization of subobject
[-Wmissing-braces]
struct dc_surface_dcc_cap output = {0};
^
{}
Previous efforts to fix this type of warning by adding or removing
braces have been met with some pushback in favor of using memset [1][2].
Do that here, mirroring commit 05794eff1a ("drm/amdgpu/gmc: fix
compiler errors [-Werror,-Wmissing-braces] (V2)") in this tree.
[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
Fixes: 7df7e505e8 ("drm/amd/display: Set requested plane state DCC params for GFX9")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:5089:60:
warning: suggest braces around initialization of subobject
[-Wmissing-braces]
struct dc_surface_update dummy_updates[MAX_SURFACES] = { 0 };
^
{}
Previous efforts to fix this type of warning by adding or removing
braces have been met with some pushback in favor of using memset [1][2].
Do that here, mirroring commit 05794eff1a ("drm/amdgpu/gmc: fix
compiler errors [-Werror,-Wmissing-braces] (V2)") in this tree.
[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
Fixes: 02d6a6fcdf ("drm/amd/display: Simplify underscan and ABM commit")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:50:57:
warning: suggest braces around initialization of subobject
[-Wmissing-braces]
union training_aux_rd_interval training_rd_interval = {0};
^
{}
1 warning generated.
Previous efforts to fix this type of warning by adding or removing
braces have been met with some pushback in favor of using memset [1][2].
Do that here, mirroring commit 05794eff1a ("drm/amdgpu/gmc: fix
compiler errors [-Werror,-Wmissing-braces] (V2)") in this tree.
[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
Fixes: 3cec41769d ("drm/amd/display: Fix use of uninitialized union")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP was missing in the checks for supported VRR connectors.
[How]
Attach the properties for eDP connectors too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202449
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- Split out some part of drm_crtc_helper.h into drm_probe_helper.h
- DRIVER_* flags improvements
- New tasks on the TODO-list
- Improvements to the documentation
Driver Changes:
- Continual of drmP.h removal in multiple drivers
- Removal of FBINFO_(FLAG_)DEFAULT in multiple drivers
- sun4i: Addition of the A23 support, multiple fixes for the tiled
formats
- atmel-hlcdc: Fix of clipping and rotation properties
- qxl: various BO-related improvements, prime and generic fbdev emulation
support
- dw-hdmi: Support for HDMI2.0 2160p modes and YUV420 output
- New Sitronix ST7701 panel driver
- New Kingdisplay KD097D04 panel driver
- New LeMaker BL035-RGB-002 panel driver
- New PDA 91-00156-A0 panel driver
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXFRb/wAKCRDj7w1vZxhR
xXj2AQDFAkH0/tksJ+T6yrHZXQE7q/6fAWTlrDXLo7Nb1hhfswEA1AyaHmZJA0Ar
u7S+4Gfzs/gisw9Jr4bqQaerEpYJxQA=
=qumD
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-02-01' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- Split out some part of drm_crtc_helper.h into drm_probe_helper.h
- DRIVER_* flags improvements
- New tasks on the TODO-list
- Improvements to the documentation
Driver Changes:
- Continual of drmP.h removal in multiple drivers
- Removal of FBINFO_(FLAG_)DEFAULT in multiple drivers
- sun4i: Addition of the A23 support, multiple fixes for the tiled
formats
- atmel-hlcdc: Fix of clipping and rotation properties
- qxl: various BO-related improvements, prime and generic fbdev emulation
support
- dw-hdmi: Support for HDMI2.0 2160p modes and YUV420 output
- New Sitronix ST7701 panel driver
- New Kingdisplay KD097D04 panel driver
- New LeMaker BL035-RGB-002 panel driver
- New PDA 91-00156-A0 panel driver
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190201144749.t3abxvguhstu6bcl@flea
[Why]
The earlier change 'Fix 6x4K displays' led to fclk value
idling at higher DPM level.
[How]
Apply the fix only to respective multi-display configuration.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New stuff for 5.1.
amdgpu:
- DC bandwidth formula updates
- Support for DCC on scanout surfaces
- Support for multiple IH rings on soc15 asics
- Fix xgmi locking
- Add sysfs interface to get pcie usage stats
- Simplify DC i2c/aux code
- Initial support for BACO on vega10/20
- New runtime SMU feature debug interface
- Expand existing sysfs power interfaces to new clock domains
- Handle kexec properly
- Simplify IH programming
- Rework doorbell handling across asics
- Drop old CI DPM implementation
- DC page flipping fixes
- Misc SR-IOV fixes
amdkfd:
- Simplify the interfaces between amdkfd and amdgpu
ttm:
- Add a callback to notify the driver when the lru changes
sched:
- Refactor mirror list handling
- Rework hw fence processing
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125231517.26268-1-alexander.deucher@amd.com
[Why]
The flip and full structures were allocated but never freed.
[How]
Free them at the end of the function. There's a small behavioral
change here with the function returning early if the allocation fails
but we wouldn't should be doing anything in that case anyway.
Fixes: c00e0cc0fdc0 ("drm/amd/display: Call into DC once per multiplane flip")
Fixes: ea39594e0855 ("drm/amd/display: Perform plane updates only when needed")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enhanced sync need to use vertical_interrupt1.
[How]
Add vertical_interrupt1 source to irq manger,
Implment setup vline interrupt interface.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During any modeset the CRTC stream is removed and a new stream is added.
This new stream doesn't carry over CRC capture state if it was
previously set.
[How]
Re-program the stream for CRC capture. The existing DRM callback can
be re-used here for the most part - the only modification needed is
additional locking now that it's called from within commit tail.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to read CRC events when CRC capture is enabled the vblank
interrput handler needs to be running for the CRTC. The handler is
enabled while there is an active vblank reference.
When running IGT tests there will often be no active vblank reference
but the test expects to read a CRC value. This is valid usage (and
works on i915 since they have a CRC interrupt handler) so the reference
to the vblank should be grabbed while capture is active.
This issue was found running:
igt@kms_plane_multiple@atomic-pipe-b-tiling-none
The pipe-b is the only one in the initial commit and was not previously
active so no vblank reference is grabbed. The vblank interrupt is
not enabled and the test times out.
[How]
Keep a reference to the vblank as long as CRC capture is enabled.
If userspace never explicitly disables it then the reference is
also dropped when removing the CRTC from the context (stream = NULL).
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On current design, driver cannot handle the interrupt for
down reply when link training is processing. The DOWN REQ
send before link training will keep in the pending DOWN REP
state in the queue.
It makes the next DOWN REQ be queued until time out.
[How]
To add a polling sequence before clear payload allocation table
to make sure the pending DOWN REP can be handled.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
arch/x86/Makefile disables SSE and SSE2 for the whole kernel. The
AMDGPU drivers modified in this patch re-enable SSE but not SSE2. Turn
on SSE2 to support emitting double precision floating point instructions
rather than calls to non-existent (usually available from gcc_s or
compiler_rt) floating point helper routines.
Link: https://gcc.gnu.org/onlinedocs/gccint/Soft-float-library-routines.html
Link: https://github.com/ClangBuiltLinux/linux/issues/327
Cc: stable@vger.kernel.org # 4.19
Reported-by: S, Shirish <Shirish.S@amd.com>
Reported-by: Matthias Kaehlcke <mka@google.com>
Suggested-by: James Y Knight <jyknight@google.com>
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] After call bios table crtc_source_select, dal will program fmt
again. The bios table program dig_source_select and other fmt register
for bios usage which is redundancy and uncessary.
[How] Program dig_soruce_select register directly
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previously we incorrectly skipped backlight control when stream is
present but dpms_off = true. This causes backlight to remain on in
the we boot up or resume into a external display only configuration
where VBIOS posted on the eDP.
[How]
Add dpms_off into the condition for edp need to turn off.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change causes regression for S4 resume where gamma is not
programmed. The change incorrectly updates the requested dpms_off
state.
This reverts commit d2b1d6bbc5.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Improved contrast in ABM 2.2 is desired
[How]
Increase the contrast factor for ABM levels 2, 3 and 4
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Our output TF calculation doesn't work if no user-specified gamma
correction. Normally, user provides this, but driver sohuld just assume
default (linear) gamma otherwise.
[How] Remove output TF dependency on user gamma being provided.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
An uninitialized variable would randomly initialize to a large
value. This caused enough delay to fail DP Compliance Test 400.2.1.
[How]
Initialize the variable.
Signed-off-by: John Barberiz <John.Barberiz@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need method of detecting which version of the DMCU FW is loaded and
load the appropriate iRAM.
[How]
Create definition for ABM 2.2 iRAM, and load it if the DMCU FW version
number matches the ABM 2.2 version; otherwise load ABM 2.1 iRAM.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current date based versioning doesn't tell us about feature version
and build version, and is not useful for debug.
[How]
Add versioning based on feature and build
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We were assuming that any commit with allow_modeset == false
was a pageflip. This was against drm intention and only
worked by sheer luck
[How]
A pageflip is the change from one framebuffer to another
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Our old logic: if pageflip, update freesync and plane address.
Otherwise, update everything.
This over-updated on non-pageflip cases, and it failed to
update if pageflip and non-pageflip changes occurred on
the same commit
[How]
Update flip_addrs on pageflips.
Update scaling_info when it changes.
Update color fields on color changes.
Updates plane_info always because we don't have a good way of
knowing when it needs to be updated.
Unfortunately, this means that every stream commit involves two
calls into DC. In particular, on pageflips there is a second,
pointless update that changes nothing but costs several
microseconds (about a 50% increase in time taken). The update is
fast, but there are comparisons and some useless programming.
Leave TODOs indicating dissatisfaction.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
amdgpu_dm_commit_planes was performing multi-plane
flips incorrectly:
It waited for vblank once per flipped plane
It prepared flip ISR and acquired the corresponding vblank ref
once per plane, although it closed ISR and put the ref once
per crtc
It called into dc once per flipped plane, duplicating some work
[How]
Wait for vblank, get vblank ref, prepare flip ISR, and call into
DC only once, and only if there is a pageflip
Make freesync continue to update planes even if vrr information
has already been changed
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underscan and ABM are connector properties but require updates
to DC stream state. Previously, on updates to these properties
the affected stream and all its planes were committed.
This is unnecessary; only a few fields on the stream need
to be changed.
[How]
If scaling or ABM have changed, change the stream and
create a stream update with those changes. Call
DC with only those fields.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC was assuming that any surface_update->scaling_info
meant the update was at least medium. However, if nothing
has changed there is no scaling to program, so there is
no problem with the update being fast
[How]
If every update flag is not set, the update is fast
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Virtual memory allows display to support flipping to surfaces which
are not allocated contiguously in memory with physical addresses,
instead a 1-4 level page table is used.
This is beneficial because it allows the scattering of large surfaces
to improve memory efficiency and security.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Change DCN10 hubbub to use hubbub as a base and allow all future DCN
hubbubs to do the same instead of using DCN10_hubbub. This increases
readability and doesn't require future hubbubs to inherit anything
other than the base hubbub struct.
[How]
Create separate DCN10_hubbub struct which uses the hubbub struct as
a base.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For fastboot, Bios will light up eDP before SW driver is loaded. SW
driver will check if eDP is lit by bios through reading the
BIOS_SCRATCH_3 register. If lit, SW driver will not power down eDP
power and phy to save time.
Definition of BIOS_SCRATCH_3 are missing for pre-raven asic. This
causes eDP fast boot to not work property. For some eDP panels, even
if dp tx sends NoVideoStream_flag =1 and dpcd 0x600=2, eDP rx may not
handle properly. This may cause a short flash on screen.
[How] Add definition of BIOS_SCRATCH_3 for all asic
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Yongqiang Sun <yongqiang.sun@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the gfxclk for SMU11 can have at most 16 discrete levels.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace kzalloc() function with its 2-factor argument form, kcalloc().
This patch replaces cases of:
kzalloc(a * b, gfp)
with:
kcalloc(a, b, gfp)
Also, improve the coding style and the use of sizeof during
allocation by changing sizeof(struct dc_surface_update) and
sizeof(struct dc_plane_state) to sizeof(*updates) and
sizeof(*surfaces), correspondingly.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes printing clock names in cases like:
[ 5.352311] [drm] DM_PPLIB: values for Invalid clock
[ 5.352313] [drm] DM_PPLIB: 400000 in kHz
[ 5.352313] [drm] DM_PPLIB: 933000 in kHz
[ 5.352314] [drm] DM_PPLIB: 1067000 in kHz
[ 5.352315] [drm] DM_PPLIB: 1200000 in kHz
[ 5.352317] [drm] DM_PPLIB: values for Invalid clock
[ 5.352318] [drm] DM_PPLIB: 300000 in kHz
[ 5.352318] [drm] DM_PPLIB: 600000 in kHz
[ 5.352319] [drm] DM_PPLIB: 626000 in kHz
[ 5.352320] [drm] DM_PPLIB: 654000 in kHz
(source: HP EliteBook 745 G5 w. RAVEN 0x1002:0x15DD 0x103C:0x83D5 0xD1)
On my system above "Invalid" names got replaced by "F" and "DCF".
The same problem was occurring on Huawei Matebook D with just 667000 kHz
instead of 400000 kHz.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check if crtc state is changed so that mode set is
required before trying to create new stream.
It deals with the MST hotplug use case when plug back to the
same connector where the failure to create new stream for the
inactive crtc on the old connector.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Having the probe helper stuff (which pretty much everyone needs) in
the drm_crtc_helper.h file (which atomic drivers should never need) is
confusing. Split them out.
To make sure I actually achieved the goal here I went through all
drivers. And indeed, all atomic drivers are now free of
drm_crtc_helper.h includes.
v2: Make it compile. There was so much compile fail on arm drivers
that I figured I'll better not include any of the acks on v1.
v3: Massive rebase because i915 has lost a lot of drmP.h includes, but
not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h
there was still one, which this patch largely removes. Which means
rolling out lots more includes all over.
This will also conflict with ongoing drmP.h cleanup by others I
expect.
v3: Rebase on top of atomic bochs.
v4: Review from Laurent for bridge/rcar/omap/shmob/core bits:
- (re)move some of the added includes, use the better include files in
other places (all suggested from Laurent adopted unchanged).
- sort alphabetically
v5: Actually try to sort them, and while at it, sort all the ones I
touch.
v6: Rebase onto i915 changes.
v7: Rebase once more.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: virtualization@lists.linux-foundation.org
Cc: etnaviv@lists.freedesktop.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: spice-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-tegra@vger.kernel.org
Cc: xen-devel@lists.xen.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
[Why]
Backlight is conceptually a property of links, not streams.
All backlight programming is done on links, but there is a
stream property bl_pwm_level that is used to restore backlight
on dpms on and s3 resume. This is unnecessary, as backlight
is already restored by hardware with no driver intervention.
[How]
Remove bl_pwm_level, and the stream argument to set_backlight
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=109375
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 923fe49512)
[Why]
The cursor vanishes when touching the top of edge of the screen for
Raven on Linux.
This occurs because the cursor height is not taken into account when
deciding to disable the cursor.
[How]
Factor in the cursor height into the cursor calculations - and mimic
the existing x position calculations.
Fixes: 94a4ffd1d4 ("drm/amd/display: fix PIP bugs on Dal3")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hotplug on raven results in REG_WAIT_TIMEOUT warning
due to failing attempt to lock disabled otg for the hubp
interdependent pipes programming.
[How]
Don't setup pipe interdependencies for disabled otg.
Also removed the unnecessary duplicate logic checks.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PPLIB not receive the PME when unplug.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This fixes a stuttering issue that occurs when moving a hardware cursor
when VRR is enabled.
Previously when VRR is enabled atomic check will grab the connector
state for every atomic update. This has to lock the connector in order
to do so. The locking is bad enough by itself for performance, but
it gets worse with what we do just below that - add all the planes
for the CRTC to the commit.
This prevents the cursor fast path from working - there's more than one
plane now. With state->allow_modeset = true on top of this, it also
adds and removes all the planes from the DC context triggering a full
(very slow) update in DC.
[How]
We need the connector state to get the VRR min/max capbilities, but we
only need them when there's a CRTC mode change or when VRR is toggled.
The condition has been updated accordingly.
Fixes: 3cc22f281318 ("drm/amdgpu: Set FreeSync state using drm VRR properties")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the DMCU's iRAM definition was moved to the newly created
power_helpers, a #pragma pack was lost, causing the iRAM to be misaligned
[How]
Restore the #pragma pack
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a follow up to:
e28e1490794d ("drm/amd/display: Remove i2caux folder")
Some files were still left, so delete all of them.
CC: David Francis <David.Francis@amd.com>
CC: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Wjy&How] Some stress test is causing unexpected memory allocation
failure. This prevents null dereference but there will likely be problems
later, hard to gracefully handle memalloc fail for critical objects.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if VERT_FILTER_INIT_BOT and BLACK_OFFSET registers
exists in the DCN SCL IP block before trying to access.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Modify freesync module to build VTEM infopackets when in HdmiVRR mode
Signed-off-by: Bayan Zabihiyan <Bayan.Zabihiyan@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On DCN1, there is an issue where on high BW config on single channel
systems, underflow will be observed if DCC is disabled. This issue
can be observed on several use cases. For this particular case,
it is observed when playing 4k video on 4k desktop with video downscaled
to a certain size.
[How]
Block MPO for this particular case, this will prevent extra BW consumed
from downscaling, working around the underflow.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DP compliance box shows wrong MSA data.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hotplug on raven results in REG_WAIT_TIMEOUT warning
due to failing attempt to lock disabled otg for the hubp
interdependent pipes programming.
[How]
Don't setup pipe interdependencies for disabled otg.
Also removed the unnecessary duplicate logic checks.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] clarify dal input parameters to pplib interface, remove
un-used parameters. dal knows exactly which parameters needed
and their effects at pplib and smu sides.
current dal sequence for dcn1_update_clock to pplib:
1.smu10_display_clock_voltage_request for dcefclk
2.smu10_display_clock_voltage_request for fclk
3.phm_store_dal_configuration_data {
set_min_deep_sleep_dcfclk
set_active_display_count
store_cc6_data --- this data never be referenced
new sequence will be:
1. set_display_count --- need add new pplib interface
2. set_min_deep_sleep_dcfclk -- new pplib interface
3. set_hard_min_dcfclk_by_freq
4. set_hard_min_fclk_by_freq
after this code refactor, smu10_display_clock_voltage_request,
phm_store_dal_configuration_data will not be needed for rv.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is huge, unmaintainable, needlessly layered, and obsolete
[How]
Remove it. All of it. Also remove the i2caux struct in
dc_context and the code that created and destructed it
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The aux_engine struct is needlessly complex and
is defined multiple times. It contains function pointers
that each have only one version and are called only from
inside dce_aux.
[How]
Replace aux_engine with a new struct called dce_aux.
Remove all function pointers and call functions directly.
Remove unused functions
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The old aux interface goes through i2caux and the aux_engine
and engine function pointers. The multiple layers of indirection
make it hard to tell waht is happening. The aux algorithm
does not need to be this complicated: attempt to submit the
request. If you get an ack (reply = 0), stop. Otherwise,
retry, up to 7 times.
[How]
Add a new helper function in dce_aux that performs aux retries
Move the plumbing of the aux calling code into dce_aux
Add functions in ddc that redirect directly to dce_aux
Make all aux calls use these functions
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
aux_payload should be the struct used inside dc to start
aux transactions. This will allow the old aux interface
to be seamlessly replaced.
[How]
Add three fields to aux_payload: reply, mot, defer_delay
This will mean that aux_payload has all data required
to submit a request. Shift dc_link to use this struct
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The cursor vanishes when touching the top of edge of the screen for
Raven on Linux.
This occurs because the cursor height is not taken into account when
deciding to disable the cursor.
[How]
Factor in the cursor height into the cursor calculations - and mimic
the existing x position calculations.
Fixes: 94a4ffd1d4 ("drm/amd/display: fix PIP bugs on Dal3")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If eDP ver >= 1.4,
the Source device must use LINK_RATE_SET.
[How]
Get LINK_RATE_SET by reading DPCD 10h-1fh,
then write DPCD 00115h before link training.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain scenarios the ramp parameter come in as NULL, which crashes
because this function doesn't guard properly in the early return.
[How]
- parameter mapUserRamp should be the guard (false means no ramp)
- remove checking ramp in early return
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Acked-by: Eryk Brol <Eryk.Brol@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To resume system before entering S0i3 completely will cause PSP not
reload DMCU FW since there is not HW power state change.
In this case, driver cannot get correct DMCU version from IRAM
since driver override it and DMCU didn't reload to update it.
It makes driver return false in dcn10_dmcu_init().
[how]
1.To redefine DMCU_SCRATCH to identify different DMCU state.
2.To reserve IRAM 0xF0~0xFF write by DMCU only.
3.To remove dcn10_get_dmcu_state
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PPLIB not receive the PME when unplug.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
separate register access from logic to allow us abstract register sequences
[how]
consolidate mask and value first then apply to register.
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 717276b925.
The reverted patch was a workaround that addressed an issue fixed by:
4364bcb2cd ("drm: Get ref on CRTC commit object when waiting for
flip_done")
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1-Test equipment does not reset test automation flag after completing
current test causing the next test to fail.
2.When test request is empty, we shouldn't ack the test.
[How]
1-Driver should always clear test equipment automation test request
when request is completed.
2-Driver should clear test equipement test automation if driver does
not complete the request.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the DMCU's iRAM definition was moved to the newly created
power_helpers, a #pragma pack was lost, causing the iRAM to be misaligned
[How]
Restore the #pragma pack
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The driver will crash on dce hardware due to a null function pointer.
[How]
- bring back "program_csc_matrix" functionality as "program_output_csc" for
dce110
- dce110 doesn't use the "opp_id" parameter, so use 0 when there's no hubp
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This fixes a stuttering issue that occurs when moving a hardware cursor
when VRR is enabled.
Previously when VRR is enabled atomic check will grab the connector
state for every atomic update. This has to lock the connector in order
to do so. The locking is bad enough by itself for performance, but
it gets worse with what we do just below that - add all the planes
for the CRTC to the commit.
This prevents the cursor fast path from working - there's more than one
plane now. With state->allow_modeset = true on top of this, it also
adds and removes all the planes from the DC context triggering a full
(very slow) update in DC.
[How]
We need the connector state to get the VRR min/max capbilities, but we
only need them when there's a CRTC mode change or when VRR is toggled.
The condition has been updated accordingly.
Fixes: 3cc22f281318 ("drm/amdgpu: Set FreeSync state using drm VRR properties")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To reduce indent in dm_update_crtcs, and to make it operate on single
instances.
[How]
Move iteration of plane states into atomic_check.
No functional change is intended.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To reduce indentation of dm_update_planes, and to make it operate on
single plane instances.
[How]
Move iteration of plane states into atomic_check.
No functional change is intended.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix boolean expression by using logical AND operator '&&'
instead of bitwise operator '&'.
This issue was detected with the help of Coccinelle.
Fixes: 6d04ee9dc1 ("drm/amd/display: Restructuring and cleaning up DML")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardware support for Delta Color Compression (DCC) decompression is
available in DC for GFX9 but there's no way for userspace to enable
the feature.
Enabling the feature can provide improved GFX performance and
power savings in many situations.
[How]
The GFX9 DCC parameters are passed to amdgpu_dm from AMDGPU via the
amdgpu_bo tiling_flags. The plane capability is queried and the
parameters are set accordingly.
The DCC address is given via a 256 byte aligned offset on the
framebuffer address. The DCC address is updated whenever the buffer
address changes.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
32-bit builds break when doing 64-bit division directly.
[How]
Use the div_u64() function instead to perform the division.
Fixes: https://lists.freedesktop.org/archives/dri-devel/2018-December/201008.html
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Initializing structures with { } is known to be problematic since
it doesn't necessararily initialize all bytes, in case of padding,
causing random failures when structures are memcmp().
This patch fixes the structure initialisation related compiler
error by memset.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For more informative debugging.
[How]
Add timing generator and PLL ids to output, to make it clear which pixel
clock is being set.
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove reg_helper.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove custom_float.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove custom_float.h which is included more than once
Acked-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are several variables that are defined and never used and hence can
be removed. Remove them. Cleans up clang -Wunused-const-variable warnings:
warning: ‘dvi_hdmi_dongle_signature_str’ defined but not used
warning: ‘dce11_one_lpt_channel_max_resolution’ defined but not used
warning: ‘ddc_hw_status_addr’ defined but not used
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function dc_commit_updates_for_stream had a parameter called
plane_states. It was never used. It was getting in the way
of some cleanup work
[How]
Remove it
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will allow us to program dscclk to required value
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PPLib has impelemented the new pp_smu interface
[How]
Use the new functions if available instead of the old interface
'set_display_requirement' and 'dcn1_pplib_apply_display_requirements'.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Su Chung <Su.Chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When XGMI is enabled, we need to adjust the dprefclk according to the
WAFL link's spread spectrum info. This is for VG20 (DCE121) only.
[How]
dce_clk_mgr already stores SS info, currently being used by audio clock.
Therefore, patch the clk_mgr's SS info with the xGMI SS info, if xGMI
is enabled. For display clock, adjust it during dce12_update_clocks()
before calling set_clock().
Since we rely on a mmhub register to reliably determine if xGMI is
enabled, the patching step needs to happen after resource_construct()
has initialized the hardware sequencer.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This fixes an regression introduced by:
drm/amd/display: add stream ID and otg instance in dc_stream_state
During driver initialization, a null pointer deref is raised. This is
caused by searching for a stream status in the dc->current_state before
the dc_state swap happens at the end of dc_commit_state_no_check().
Since the swap has not happened, the dc_state to be swapped in should
be searched, and not dc->current_state.
[How]
Add a function that searches for the stream status within the given
dc_state, instead of dc->current_state. Use that before the state swap
happens in dc_commit_state_no_check().
Also remove duplicate occurrences of this function in amdgpu_dm.c.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
context->bw.dce.dispclk_khz is being cached into unpatched_clock, then
restored at end of function call. This is needlessly complex
[How]
Instead, use a local patched_clock variable. Leave
context->bw.dce.dispclk_khz alone.
No functional change is intended.
Signed-off-by: David Francis <david.francis@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are different reasons for Validation failure error during
atomic_check
[How]
Add better logging of the reason for validation failure
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Users would like more accurate pixel clocks, especially for fractional
"TV" frame rates like 59.94 Hz.
[How]
Store and communicate pixel clocks with 100 Hz accuracy from
dc_crtc_timing through to BIOS command table setpixelclock call.
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There is an extra null check for fs_params in the
build_freesync_hdr function detected by Smatch.
[HOW]
1) Remove the extra null check since it is checked in the
caller.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's not being used anywhere.
[How]
Remove it.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ABM enablement testing can be automated if a way of reading
target and current hardware backlight is available
[How]
Expand debugfs interface with two new entries.
Hook directly into dc interface. Units are as
a fraction of 0x1000 = 100%
Use the built-in amdgpu function for creating
read-only debugfs files
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
stream ID allows DMs to avoid memory address comparisons to compare
stream equality.
otg_instance allows DC to more rigorously define when otg_instance
can change. specifically, it is now defined to be only mutable when dc_stream_state
changes. This is better than a "get status" function which prevents efficient
caching of otherwise very stable information.
[how]
stream ID follows similar pattern to sink ID, which is already implemented
otg_instance is an output which occurs on all dc_stream modification functions
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DV have made updates to DCN dml which we need to pull in
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Backlight is conceptually a property of links, not streams.
All backlight programming is done on links, but there is a
stream property bl_pwm_level that is used to restore backlight
on dpms on and s3 resume. This is unnecessary, as backlight
is already restored by hardware with no driver intervention.
[How]
Remove bl_pwm_level, and the stream argument to set_backlight
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
They're not being used, so remove them.
Signed-off-by: Imad Syed <imad.syed@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc_stream_state containing a pointer to sink is poor design.
Sink describes the display, and the specifications or capabilities
it has. That information is irrelevant for dc_stream_state, which describes
hardware state, and is generally used for hardware programming. It
could further be argued that dc_sink itself is just a convenience dc
provides, and DC should be perfectly capable of programming hardware
without any dc_sinks (for example, emulated sinks).
[how]
Phase 1:
Deprecate use of dc_sink pointer in dc_stream. Most references are trivial
to remove, but some call sites are risky (such as is_timing_changed) with
no obvious logical replacement. These will be removed in follow up change.
Add dc_link pointer to dc_stream. This is the typical reason DC really needed
sink pointer, and most call sites are replaced with this.
DMs also need minor updates, as all 3 DMs leverage stream->sink for
some functionality. this is replaced instead by a pointer to private data
inside dc_stream_state, which is used by DMs as a quality of life improvment
for some key functionality. it allows DMs to set pointers have to their own objects
which associate OS objects to dc_stream_states (such as DisplayTarget
and amdgpu_dm_connector). Without the private pointer, DMs would be
forced to perform a lookup for callbacks.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
So that we can adjust fclk for debugging purposes.
[How]
Add option to force adjust fclk request to pplib.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There was a recent fix in the BW spreadsheet to allow timing with very
large vblank. Need to be ported into driver.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We are not correctly handling the wrap around case.
VLine interrupt is relative to position of VUpdate interrupt.
Both VUpdate interrupt and VLine interrupt could possibly
be in front porch or back porch.
[How]
Fix wraparound case by checking for line number that is
greater than the VTOTAL of the OTG timing. In this case,
the interrupt should occur on the next frame.
Also fix some variable naming and remove some dead code.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver didn't check plane size and surface size is mismatch.
It will cause pitch data incorrect.
[How]
Add condition to check is plane change and update surface
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some components depend on dc to constuct
but need to assign callback functions to dc.
[how]
Instead of assigning dc callback functions in dc_create,
decouple the callback init to a standlone function after dc_create. This
is currently a no-op.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove braces around single-line conditionals
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To make sure future changes in DAL for SMU msgs will not change the current behaviour
and to make sure clock registeres are programmed correctly based on SMU msgs
that DAL sends.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Yongqiang Sun <yongqiang.sun@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1) Rename and make public definition of input CSC matrix struct.
2) Make wm_read_state() function an interface of hubbub, and check
if watermark registers exist before read/write to them.
3) Check if OTG_INTERLACE_CONTROL register exists before updating
4) Add dummy functions for set_input/output_transfer function to avoid
errors due to differences in CM registers.
5) Added missing register field definition in header file
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Expose this function for future use.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Shahin Khayyer <Shahin.Khayyer@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-next has been forwarded to 5.0-rc1, and we need it to apply the damage
helper for dirtyfb series from Noralf Trønnes.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Just like i915 and nouveau, it's a good idea for us to hold a malloc
reference to the port here so that we never pass a freed pointer to any
of the DP MST helper functions.
Also, we stop unsetting aconnector->port in
dm_dp_destroy_mst_connector(). There's literally no point to that
assignment that I can see anyway.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@redhat.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: Juston Li <juston.li@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190111005343.17443-12-lyude@redhat.com
