Adds support for handling of clocking relevant to the DCN3 block
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN3, which entails our
stream and link encoders.
HW Blocks:
+--------+
| DIO |
+--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dal side nv12 wa has a lot of side effects.
KMD side wa is used, so this should be remove.
[How]
Removed wa from dal side.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.
[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And only set to 400us if LTTPR is not present.
Before this piece of logic is interwined with LTTPR support.
Now we will default to 3.2ms aux timeout even if LTTPR support is not
enabled by driver.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We dropped the delay after changed the cursor functions locking the
entire pipe to locking just the CURSOR registers to fix page flip
stuttering - this introduced cursor stuttering instead, and an underflow
issue.
The cursor update can be delayed indefinitely if the cursor update
repeatedly happens right around VUPDATE.
The underflow issue can happen if we do a viewport update on a pipe
on the same frame where a cursor update happens around VUPDATE - the
old cursor registers are retained which can be in an invalid position.
This can cause a pipe hang and indefinite underflow.
[How]
The complex, ideal solution to the problem would be a software
triple buffering mechanism from the DM layer to program only one cursor
update per frame just before VUPDATE.
The simple workaround until we have that infrastructure in place is
this change - bring back the delay until VUPDATE before locking, but
with some corrections to the calculations.
This didn't work for all timings before because the calculation for
VUPDATE was wrong - it was using the offset from VSTARTUP instead and
didn't correctly handle the case where VUPDATE could be in the back
porch.
Add a new hardware sequencer function to use the existing helper to
calculate the real VUPDATE start and VUPDATE end - VUPDATE can last
multiple lines after all.
Change the udelay to incorporate the width of VUPDATE as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current odm/mpc combine logic to detect which pipes need to split
logically is flawed leading to incorrect pipe merge/split operations
being taken.
This change cleans up the logic and fixes the logical errors.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
What a mode change is requested for the same timing a full stream reset
can occur in some cases which causes monitor to blank for a few seconds.
[How]
Do not consider infoframe updates as needing a full stream reset as they
will be handled on the first flip after a modeset when surface
information is available.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
panel_cntl specific register should be access in panel_cntl object.
[How]
Move these register access from abm to panel_cntl.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current locking scheme for cursor can result in a flip missing
its vsync, deferring it for one or more vsyncs. Result is a
potential for stuttering when cursor is moved.
[How]
Use cursor update lock so that flips are not blocked while cursor
is being programmed.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add set backlight to hw sequencer, dmu communication will
be handled in hw sequencer for new asics.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
it doesn't represent panel specifically, it's more like the control
logic for the panel
[How]
change from panel to panel cntl to make it a bit more clear
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
panel power sequencer is currently just sitting in hwseq but it really
it tied to internal panels
[How]
make a new panel struct to contain power sequencer code
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Optc needs to know if timing is enabled with ODM or DSC before computing
crc. Otherwise value computed will be inaccurate. Before this change,
the CRC computed without ODM is not equal to the CRC computed with ODM
for the same timing. This is unexpected as we are driving the same
timing despite of the underlaying hardware setup to achieve it. This is
caused by missing hardware programming sequence to support it.
[how]
Add the new programming sequence based on hardware guide.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Set backlight calls to firmware are are being prevented by dmcu == null
check. Dmcu is expected to be null in this case.
[How]
Only prevent call if dmcu and abm are null. Also rename variable
'use_smooth_brightness' to 'fw_set_brightness' as it's more appropriate.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The HUBBUB watermark registers are in an area that cannot be power
gated, but the HUBP copies of the watermark values are in areas that can
be power gated. When we power on a pipe, it will not automatically take
the HUBBUB values, we need to force propagation by writing to a
watermark register.
[How]
- new HUBBUB function to re-write current value in a WM register
- touch WM register after enabling the plane in program_pipe
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dml merges mpc/odm combine pipes to do calculations. This merge is
imperfect if there is a viewport overlap. This change saves pre overlap
viewport for dml use.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On headless boot a DIG may be turned on by VBIOS on RN. This leads to
display_count being non-zero in hybrid graphics cases leading to SMU
DISPLAY_OFF message not being sent.
[HOW]
Power down hardware on boot
if seamless boot is not occurring
(power_down_display_on_boot == 1)
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver must pass abm config table to dmub fw. This provides various
parameters for abm functionality.
[How]
There is too much data to be passed in an inbox message, so we must pass
this data using an indirect buffer. Copy the table to cw7 via x86,
driver copies to fw_state structure.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
before update dpp DTO, we check dppclks in context to determine it is
changed or not, but dppclks in context will be updated anyways after
flip is done, so compare dppclks in context will always get an equal
result.
[How]
Add pipe dpp clks in dccg and compare values between dccg and context.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Causes regression with MST DSC displays not lighting up after DPMS
[how]
Revert commit 8cc426d79b ("drm/amd/display: Program DSC during timing programming")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When hotplug a HDMI monitor during entering S0i3 or DPMSOFF state due to
entering infinite loop when calling vbios to program pixel clocks. In
this scenario, pll is enabled but phy is not, and there is not a
programing guide for this case.
[How]
Before we having the proper programing guide, before disable pll, doing
a phy enable and disable to avoid the issue.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Link or DIG BE can't be exposed to a higher stream bandwidth than they
can handle. When DSC is required to fit the stream into the link
bandwidth, DSC has to be programmed during timing programming to ensure
this. Without it, intermittent issues such as black screen after S3 or a
hot-plug can be seen.
[how]
Move DSC programming from enabling stream on link to timing setup.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When combining two or more pipes in DSC mode, there will always be more
than 1 slice per line. In this case, as per DSC rules, the sink device
is expecting that the ICH is reset at the end of each slice line (i.e.
ICH_RESET_AT_END_OF_LINE must be configured based on the number of
slices at the output of ODM). It is recommended that software set
ICH_RESET_AT_END_OF_LINE = 0xF for each DSC in the ODM combine. However
the current code only set ICH_RESET_AT_END_OF_LINE = 0xF when number of
slice per DSC engine is greater than 1 instead of number of slice per
output after ODM combine.
[how]
Add is_odm in dsc config. Set ICH_RESET_AT_END_OF_LINE = 0xF if either
is_odm or number of slice per DSC engine is greater than 1.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When test pattern is enabled with ODM combine, test pattern is generated
by piecing multiple DPGs image together. The current code will program
all DPGs with horizontal offset of 0. This will cause all DPGs to output
the beginning of the pattern. Instead each DPG should program a
horizontal offset of its x position to form a continous pattern when
pieced together.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we have single channel memory, we can not light up 2 4k displays
with a 1080p edp, because we don't have enough bw by a small margin.
this small margin comes from dcc meta being too large. We however don't
have this dcc meta when we create fake planes so, before the flip we
will not filter out the mode for 2 4k displays with a 1080p edp
[how]
Change get_default_swizzle_mode to something more general so we don't
end up with a separate function for every missing field in the fake
plane. Add a reasonable dcc meta to the fake plane when it is filled in,
so we filter out modes that don't have enough bandwidth. To do this, we
take the screen width and align it to 1024(8k 60)
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some asics don't support FEC but FEC overhead is added into link
bandwidth calculation by mistake. This causes certain timing cannot be
validated.
[how]
Only include FEC overhead if both asic and display support FEC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow sometimes occurs during transition into MPO with stutter
enabled.
[How]
When transitioning into MPO, disable stutter. Re-enable stutter within
one frame.
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some display configuration like 1080P monitor playing a 1080P video,
if user use ALT+F4 to exit Movie and TV, there is a chance clocks are
same only water mark changed. Current clock optimization machanism will
result in water mark keeps high after exit Movie and TV app.
[How]
Return if watermark need to be optimized when doing program watermark,
perform the optimization after.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make panel backlight and power on/off functions into
hardware specific function pointers
[How]
Add function pointers for panel related hw functions
- is_panel_powered_on
- is_panel_backlight_on
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Add optimization to allow pstate change support when all displays
are off in DCN2.
[How]
Add clk_mgr_helper_get_active_plane_cnt() to sum plane_count for all
valid stream_status[]. If plane_count is 0, then there are no active
or virtual streams present. Use plane_count == 0 as extra condition to
enable p_state_change_support in dcn2_update_clocks().
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's used by more than just DCN2.0. Fixes missing symbol when
amdgpu is built without DCN support.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] old panel has been enabled for window driver but not linux.
[How] enable oled panel support for linux. this patch is dc part.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Having watermark ranges saved inside clk_mgr to be
available for debug at all times would be useful.
Add it to the clk_mgr_internal struct for reference.
Only populated for Renoir, unused for other asics.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
new HW engine mapping requirment use in PSP
[how]
report stream_enc_inst
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Screen flickering when HDR switches between FP16 and ARGB2101010
[How]
Moved pipe_control_lock so stream update and plane update occur atomically
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Diagnostics team reported various issues found when enabling warnings as errors
[How]
Fix implicit conversions
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Eventually want to lock at a higher level in stack.
To do this, we need to be able to isolate the parts that need to be done
after pipe unlock.
[How]
Split out programming that is done post unlock.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to fix DML portability issues to enable SW unit testing around DML
[how]
Move calcs into dc include folder since multiple components reference it
Remove relative paths to external dependencies
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only need to do surface flip for video plane via dmcub.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dpcd cap mismatch in 2200 vs base
[How]
Add monitor patch which using based caps to overwrite 2200
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With different refresh rate panels, the PSR entry/exit time is
different since it is dependent on 2 frame entry time today
[How]
Make static screen num frame entry time to be calculated
such that entry time is within 30 ms instead of fixed num
frames.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recent double buffering changes for dcn2 use IX_REG_READ.
However, this macro returns the full register value, with the need to
manually shift and mask it to retrieve field data.
[How]
Create new IX_REG_GET macro that handles shift and mask.
Use this for double buffering reads instead of IX_REG_READ.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Moving PSR from DMCU to DMCUB.
[How]
Add driverside PSR changes required to send inbox messages to fw.
These changes are non-functional until the psr structure allocation
is uncommented.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting video brightness, screen tearing was observed.
This was due to overwritten values in ICSC registers. In dcn10, this issue had been
fixed by implementing double buffering via alternating ICSC modes.
However, the second register set used in dcn1 doesn't exist in dcn2.
[How]
Create new program_input_csc for dcn20.
Use ICSC_B registers instead of COMA registers as second set.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add warmup escape support, for diags, in a way that is possible to
choose a new or an existing sequence. For achieving this goal, this
commit adds separated MCIF buffer as VCN request.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need previously implemented chroma vp wa to work for rotation cases.
[How]
Implement rotation specific wa.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previous Renoir chroma viewport workaround fixed an MPO flicker by
increasing the chroma viewport size. However, when the MPO plane is
rotated 180 degrees, the viewport is read in reverse. Since the workaround
increases viewport size, when reading in reverse it causes a vertical
chroma offset.
[HOW]
Pass rotation value to viewport set functions
Temporarily disable the chroma viewport w/a when hubp is rotated 180 degrees
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before was using HW counter value to determine the dprefclk. Which
take into account ss, but has large variation, not good enough for
generating audio dto. Also, the bios parser code to get the ss
percentage was not working.
[How]
After this change, dprefclk is hard coded, same as on RV. We don't
expect this to change on Renoir. Modified bios parser code to get
the right ss percentage.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Link training failed randomly when plugging USB-C display in/out.
[How]
If link training failed, reset PHY in link re-training.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some function pointers in the hwss function pointer table are
meant to be hw sequencer entry points to be called from dc.
However some of those function pointers are not meant to
be entry points, but instead used as a code reuse/inheritance
tool called directly by other hwss functions, not by dc.
Therefore, we want a more clear separation of which functions
we determine to be interface functions vs the functions we
use within hwss.
[How]
DC interface functions will be stored in:
struct hw_sequencer_funcs
Functions used within HWSS will be stored in:
struct hwseq_private_funcs
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers.
[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need validation that we are programming the expected values (rq, ttu, dlg)
from DML. This debug feature will output logs if we are programming
incorrect values and may help differentiate DAL issues from HW issues.
[How]
Dump relevant registers for each pipe with active stream. Compare current
reg values with the converted DML output. Log mismatches when found.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is becoming increasingly hard to figure out which
function is called on the different DCN versions
[How]
1. Make function pointer table init in its own init.c file
2. Remove other scenarios in hwseq.c file that need to
include headers of other DCN versions. (If needed,
it should have been done via the function pointers)
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In the TEST_MSIC dpcd register field definition, the test equipment
has the option to choose between YCbCr601 or YCbCr709.
We will apply corresponding YCbCr coefficient based on this test
request.
[how]
Add a new input parameter in dc_link_dp_set_test_pattern to allow the
selection between different color space.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes in dc to allow for different cases where full update is
required.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since dcn20 and dcn21 are under dcn1 it doesnt make sense to
have it named dcn1.
Change it to "dcn" to make it generic
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN21 is stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup Renoir definitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN21 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN2 and DSC are stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup NV defninitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN2 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* dce/dce_dmcu.c: dcn20_*lock_phy()
* dce/dce_dmcu.c: dcn20_funcs
* dce/dce_dmcu.c: dcn20_dmcu_create()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1-Read lttpr caps in 5-bytes
2-Parse caps
3-Validate caps and set lttpr_mode
4-Use hw default timeout when lttpr is disabled.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The aux timeout value is not default before reading link cap.
Setting it to default when lttpr is not enabled causes some monitor
not to light up.
[How]
Read the aux engine timeout value before setting it to extended.
Set the aux engine timeout to its previous value if no lttpr.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1-If at least one repeater is present in the link and we are in non
transparent mode, perform clock recovery then channel equalization
with all repeaters one by one before training DPRX.
2-Mark the end of LT with a repeater by setting training pattern 0
at the end of channel equalization with each repeater.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need it for some OEM I2C devices in Nv10
[how]
Link up code to parse OEM table and expose DC interface
to access the pins
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debug purpose, we need to check the following hardware status
in DTN log debugfs:
1.dpp & hubp clock enable;
2.crtc blank enable;
3.link phy status;
[How]
Add the upper information in the amdgpu_dm_dtn_log debugfs.
For CRTC blanked status, since DCN2 and greater reports it on the OPP
instead of OTG, we patch it in after calling optc1_read_otg_states.
Ideally, this should be done in the DCN version specific function hooks.
It has been left as a TODO item.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is confusing to sinks if we send VSC SDP only on some format. Today we
signal colorimetry format using MSA while in formats like sRGB.
But when we switch to BT2020 we set the bit to ignore MSA colorimetry and
instead use the colorimetry information in the VSC SDP.
But if sink supports signaling of colorimetry via VSC SDP we should always
set the MSA MISC1 bit 6, instead of doing so selectively.
[How]
If sink supports signaling of colorimetry via VSC SDP, and we are sending
the colorimetry info via VSC SDP with packet revision 05h, then always
set MSA MISC1 bit 6.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Support for DMUB only depends on support for DC. It doesn't use floating
point so we don't need to guard it by any specific DCN revision.
[How]
Drop the guards and cleanup the newlines around each one.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC will use DMUB for command submission and flow control during
initialization.
Register offloading as well as submitting some BIOS commands are part
of the DC internal interface but are guarded behind debug options.
It won't be functional in amdgpu_dm yet since we don't pass the
DMUB service to DC for use.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU does not keep the wm table across S3, S4, need to re-send
the table. Also defer sending the cable to after DCN bave initialized
[How]
Send table at end of init hw
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This value will be needed by dml and therefore should be externally
accessible.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit hints are unnecessary after front end programming redesign.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Watermarks not propagated to DCHUBP after it is powered on
[How]
Add temoprary function apply_DEDCN21_147_wa to apply wm settings for Renoir
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
it allows us to do urgent latency programming
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds renoir hw_seq, needed to do renoir
specific hw programing
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1-add configurable timeout support to aux engine.
2-add timeout support field to dc_caps
3-add reg_key to override extended timeout support
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Doing this allows us to split it for diffrent asics. This design will
be helpful for future Asciis.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
use vbios message to call smu for dpm level
also only program dmdata in vsyncflip as HW requirement.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
we found using an active DP to HDMI panel that we weren't validating
dp_pixel_format and hardware timing v_front_porch, causing screen to
blank and/or corrupt while attempting a seamless boot.
[how]
added checks during dc_validate_seamless_boot_timing for these values
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If 48mhz refclk is turned off during PSR, we will have issue doing
link training during detection.
[How]
Get out of PSR before detection
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When diags adds a DWB via a stream update, we calculate MMHUBBUB
paramaters, but dc->current_state has not yet been updated
when the DWB programming happens. This leads to overflow on
high bandwidth tests since the incorrect MMHUBBUB arbitration
parameters are programmed.
[How]
Pass the updated context down to the (enable|update)_writeback functions
so that they can use the correct watermarks when programming MMHUBBUB.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This function was mistakenly reverted as part of a legitimate revert. The
old version that was reverted to has bad logic, and is causing situations
where p-state change support is being toggled when it shouldn't be,
resulting in hangs.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Type-c PHY config is not align with dpcd lane count.
When those values didn't match, it cause driver do
link training with 4 lane but phy only can output 2 lane.
The link trainig always fail.
[How]
1. Modify get_max_link_cap function. According DPALT_DP4
to update max lane count.
2. Add dp_mst_verify_link_cap to handle MST case because
we didn't call dp_mst_verify_link_cap for MST case.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
memcmp is vulnerable to regression due to dc_clocks structures not being
organized properly (not "current" clock related structures being at the beginning
of the structure) and causes unnecessary setting of the optimize bit
[how]
add a dcn sepcific comparator, implement for dcn2
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HPD is not suppressed when we lower
clocks on renoir. B/c of this we do link
training when the 48mhz refclk is off, which
will cause ASIC hang.
[how]
Exit optimized power state for detection purpose.
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To compare the crc of the framebuffer data at input of
display pipeline with the crc of the otg, we need to
disable pixel formatter's dynamic expansion feature during
crc capture and keep it enable in the normal operation.
[HOW]
Expose a new interface in DM and dc for pixel formatter
(fmt dynamic bitdepth expansion control). Interface control
the FMT_DYNAMIC_EXP_EN bit, during crc capture keep
it disabled.
Signed-off-by: Robin Singh <robin.singh@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update the hdcp display parameter whenever the link is
updated, so the next time there is an update to hdcp we have the
latest display info
[How]
Create a callback, and use this anytime there is a change in the link. This will
be used later by the dm.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This change was made because DTO programming was double-buffered, which
is itself an issue. After deactivating the DTO double buffer, this
change becomes unnecessary.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1. OUTSTANDING_REQUEST_LIMIT update from 0xFF to 0x1F (HW doc update)
2. using memory type to convert UMC's MCLK to Yclk.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Edid Utility wishes to include DSC module from driver instead
of doing it's own logic which will need to be updated every time
someone modifies the driver logic.
[How]
Modify some functions such that we dont need to pass the entire
DC structure as parameter.
-Remove DC inclusion from module.
-Filter out problematic types and inclusions
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New behaviour will track global updates and update any hw that isn't
related to current stream being updated.
This should fix any issues caused by pipe split pipes being taken
by other streams.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When user mode use i2c over aux through ADL or DDI, the function
dal_ddc_service_query_ddc_data will be called. There are two issues.
1. When read/write length > 16byte, current always return false because
the DEFAULT_AUX_MAX_DATA_SIZE != length.
2. When usermode only need to read data through i2c, driver will write
mot = true at the same address and cause i2c sink confused. Therefore
the following read command will get garbage.
[How]
1. Add function dal_dcc_submit_aux_command to handle length > 16 byte.
2. Check read size and write size when query ddc data.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing parameters, to make dcn21 compile
without errors
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
call update_bw_bounding_box in DC construct
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Controls display clocks and interfaces with powerplay for
clock and power requirements.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Existing HW Features, HW Diags test requested that the
registers be exposed.
[How]
Add V_TOTAL_MID to existing DC structures.
Make sure values are passed down throughout DC
Add Register definition.
Program the additional registers
Add additional Logic for V_TOTAL_CONTROL.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
OS will reserve HW state in UEFI mode.
Driver init_hw reset to RGB which caused HDMI green in YCbCr mode.
read HW blank_color based on acc_mode.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to have the ability to to tell us set degamma on the cursor.
[How]
Pass a flag down to register programming that tells us if the
current surface format needs cursor degamma.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
