Earlier, memblock_find_in_range() was not used to find the memory to
be reserved for FADump as bottom up allocation mode was not supported.
But since commit 79442ed189 ("mm/memblock.c: introduce bottom-up
allocation mode") bottom up allocation mode is supported for memblock.
So, use it to find the memory to be reserved for FADump.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821364211.5656.14336025460336135194.stgit@hbathini.in.ibm.com
Make OPAL call to indicate that the dump is processed and the metadata
area in OPAL can be cleared/released. Also, setup/initialize FADump
for re-registration.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821356046.5656.12270927048195494911.stgit@hbathini.in.ibm.com
During kexec boot, metadata address needs to be reset to avoid running
into errors interpreting stale metadata address, in case the kexec'ed
kernel crashes before metadata address could be setup again.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821346629.5656.10783321582005237813.stgit@hbathini.in.ibm.com
OPAL allows registering address with it in the first kernel and
retrieving it after MPIPL. Setup kernel metadata and register its
address with OPAL to use it for processing the crash dump.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821345011.5656.13567765019032928471.stgit@hbathini.in.ibm.com
Except for Reserved dump area (see Documentation/powerpc/firmware-
assisted-dump.rst) which is permanent reserved, all memory above boot
memory size, where boot memory size is the memory required for the
kernel to boot successfully when booted with restricted memory (memory
for capture kernel), is released when the dump is invalidated. Make
this a bit more explicit in the code.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821336092.5656.1079046285366041687.stgit@hbathini.in.ibm.com
Move platform specific register/un-register code, the RTAS calls, to
register/un-register callback functions. This would also mean moving
code that initializes and prints the platform specific FADump data.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821332856.5656.16380417702046411631.stgit@hbathini.in.ibm.com
Introduce callback functions for platform specific operations like
register, unregister, invalidate & such. Also, define place-holders
for the same on pSeries platform.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821330286.5656.15538934400074110770.stgit@hbathini.in.ibm.com
Currently, FADump is only supported on pSeries but that is going to
change soon with FADump support being added on PowerNV platform. So,
move rtas specific definitions to platform code to allow FADump
to have multiple platforms support.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821328494.5656.16219929140866195511.stgit@hbathini.in.ibm.com
Add helper functions to setup & free CPU notes buffer and to find if a
given memory area is contiguous. Also, use boolean as return type for
the function that finds if boot memory area is contiguous. While at
it, save the virtual address of CPU notes buffer instead of physical
address as virtual address is used often.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821318971.5656.9281936950510635858.stgit@hbathini.in.ibm.com
Though asm/fadump.h is meant to be used by other components dealing
with FADump, it also has macros/definitions internal to FADump code.
Move them to a new header file used within FADump code. This also
makes way for refactoring platform specific FADump code.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821313134.5656.6597770626574392140.stgit@hbathini.in.ibm.com
This slightly improves the prom_init_check rule.
[1] Avoid needless check
Currently, prom_init_check.sh is invoked every time you run 'make'
even if you have changed nothing in prom_init.c. With this commit,
the script is re-run only when prom_init.o is recompiled.
[2] Beautify the build log
Currently, the O= build shows the absolute path to the script:
CALL /abs/path/to/source/of/linux/arch/powerpc/kernel/prom_init_check.sh
With this commit, it is always a relative path to the timestamp file:
PROMCHK arch/powerpc/kernel/prom_init_check
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190912074037.13813-1-yamada.masahiro@socionext.com
Some of the templates used for KVM patching are only used on certain
platforms, but currently they are always built-in, fix that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190911115746.12433-4-mpe@ellerman.id.au
All the code in kvm.c can be marked __init. Most of it is already
inlined into the initcall, but not all. So instead of relying on the
inlining, mark it all as __init. This saves ~280 bytes of text for my
configuration.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190911115746.12433-3-mpe@ellerman.id.au
In some configurations of KVM, guests binary patch themselves to
avoid/reduce trapping into the hypervisor. For some instructions this
requires replacing one instruction with a sequence of instructions.
For those cases we need to write the sequence of instructions
somewhere and then patch the location of the original instruction to
branch to the sequence. That requires that the location of the
sequence be within 32MB of the original instruction.
The current solution for this is that we create a 1MB array in BSS,
write sequences into there, and then free the remainder of the array.
This has a few problems:
- it confuses kmemleak.
- it confuses lockdep.
- it requires mapping kvm_tmp executable, which can cause adjacent
areas to also be mapped executable if we're using 16M pages for the
linear mapping.
- the 32MB limit can be exceeded if the kernel is big enough,
especially with STRICT_KERNEL_RWX enabled, which then prevents the
patching from working at all.
We can fix all those problems by making kvm_tmp just a region of
regular .text. However currently it's 1MB in size, and we don't want
to waste 1MB of text. In practice however I only see ~30KB of kvm_tmp
being used even for an allyes_config. So shrink kvm_tmp to 64K, which
ought to be enough for everyone, and move it into .text.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190911115746.12433-1-mpe@ellerman.id.au
The build breaks when STACKTRACE=n, eg. skiroot_defconfig:
arch/powerpc/kernel/eeh_event.c:124:23: error: implicit declaration of function 'stack_trace_save'
Fix it with some ifdefs for now.
Fixes: 25baf3d816 ("powerpc/eeh: Defer printing stack trace")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If watchpoint exception is generated by larx/stcx instructions, the
reservation created by larx gets lost while handling exception, and
thus stcx instruction always fails. Generally these instructions are
used in a while(1) loop, for example spinlocks. And because stcx
never succeeds, it loops forever and ultimately hangs the system.
Note that ptrace anyway works in one-shot mode and thus for ptrace
we don't change the behaviour. It's up to ptrace user to take care
of this.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190910131513.30499-1-ravi.bangoria@linux.ibm.com
Right now powerpc provides an implementation to read elf files
with the kexec_file_load() syscall. Make that available as a public
kexec interface so it can be re-used on other architectures.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Helge Deller <deller@gmx.de>
One fix for a boot hang on some Freescale machines when PREEMPT is enabled.
Two CVE fixes for bugs in our handling of FP registers and transactional memory,
both of which can result in corrupted FP state, or FP state leaking between
processes.
Thanks to:
Chris Packham, Christophe Leroy, Gustavo Romero, Michael Neuling.
-----BEGIN PGP SIGNATURE-----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=C+wa
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a boot hang on some Freescale machines when PREEMPT is
enabled.
Two CVE fixes for bugs in our handling of FP registers and
transactional memory, both of which can result in corrupted FP state,
or FP state leaking between processes.
Thanks to: Chris Packham, Christophe Leroy, Gustavo Romero, Michael
Neuling"
* tag 'powerpc-5.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/tm: Fix restoring FP/VMX facility incorrectly on interrupts
powerpc/tm: Fix FP/VMX unavailable exceptions inside a transaction
powerpc/64e: Drop stale call to smp_processor_id() which hangs SMP startup
Add an interface to debugfs for generating an EEH event on a given device.
This works by disabling memory accesses to and from the device by setting
the PCI_COMMAND register (or the VF Memory Space Enable on the parent PF).
This is a somewhat portable alternative to using the platform specific
error injection mechanisms since those tend to be either hard to use, or
straight up broken. For pseries the interfaces also requires the use of
/dev/mem which is probably going to go away in a post-LOCKDOWN world
(and it's a horrific hack to begin with) so moving to a kernel-provided
interface makes sense and provides a sane, cross-platform interface for
userspace so we can write more generic testing scripts.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-14-oohall@gmail.com
Detecting an frozen EEH PE usually occurs when an MMIO load returns a 0xFFs
response. When performing EEH testing using the EEH error injection feature
available on some platforms there is no simple way to kick-off the kernel's
recovery process since any accesses from userspace (usually /dev/mem) will
bypass the MMIO helpers in the kernel which check if a 0xFF response is due
to an EEH freeze or not.
If a device contains a 0xFF byte in it's config space it's possible to
trigger the recovery process via config space read from userspace, but this
is not a reliable method. If a driver is bound to the device an in use it
will frequently trigger the MMIO check, but this is also inconsistent.
To solve these problems this patch adds a debugfs file called
"eeh_dev_check" which accepts a <domain>:<bus>:<dev>.<fn> string and runs
eeh_dev_check_failure() on it. This is the same check that's done when the
kernel gets a 0xFF result from an config or MMIO read with the added
benifit that it can be reliably triggered from userspace.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-13-oohall@gmail.com
I am the RAS team. Hear me roar.
Roar.
On a more serious note, being able to locate failed devices can be helpful.
Set the attention indicator if the slot supports it once we've determined
the device is present and only clear it if the device is fully recovered.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-12-oohall@gmail.com
Currently we print a stack trace in the event handler to help with
debugging EEH issues. In the case of suprise hot-unplug this is unneeded,
so we want to prevent printing the stack trace unless we know it's due to
an actual device error. To accomplish this, we can save a stack trace at
the point of detection and only print it once the EEH recovery handler has
determined the freeze was due to an actual error.
Since the whole point of this is to prevent spurious EEH output we also
move a few prints out of the detection thread, or mark them as pr_debug
so anyone interested can get output from the eeh_check_dev_failure()
if they want.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-6-oohall@gmail.com
When a device is surprise removed while undergoing IO we will probably
get an EEH PE freeze due to MMIO timeouts and other errors. When a freeze
is detected we send a recovery event to the EEH worker thread which will
notify drivers, and perform recovery as needed.
In the event of a hot-remove we don't want recovery to occur since there
isn't a device to recover. The recovery process is fairly long due to
the number of wait states (required by PCIe) which causes problems when
devices are removed and replaced (e.g. hot swapping of U.2 NVMe drives).
To determine if we need to skip the recovery process we can use the
get_adapter_state() operation of the hotplug_slot to determine if the
slot contains a device or not, and if the slot is empty we can skip
recovery entirely.
One thing to note is that the slot being EEH frozen does not prevent the
hotplug driver from working. We don't have the EEH recovery thread
remove any of the devices since it's assumed that the hotplug driver
will handle tearing down the slot state.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-5-oohall@gmail.com
If a device is torn down by a hotplug slot driver it's marked as removed
and marked as permaantly failed. There's no point in trying to recover a
permernantly failed device so it should be considered un-actionable.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-4-oohall@gmail.com
When hot-adding devices we rely on the hotplug driver to create pci_dn's
for the devices under the hotplug slot. Converse, when hot-removing the
driver will remove the pci_dn's that it created. This is a problem because
the pci_dev is still live until it's refcount drops to zero. This can
happen if the driver is slow to tear down it's internal state. Ideally, the
driver would not attempt to perform any config accesses to the device once
it's been marked as removed, but sometimes it happens. As a result, we
might attempt to access the pci_dn for a device that has been torn down and
the kernel may crash as a result.
To fix this, don't free the pci_dn unless the corresponding pci_dev has
been released. If the pci_dev is still live, then we mark the pci_dn with
a flag that indicates the pci_dev's release function should free it.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-3-oohall@gmail.com
When the last device in an eeh_pe is removed the eeh_pe structure itself
(and any empty parents) are freed since they are no longer needed. This
results in a crash when a hotplug driver is involved since the following
may occur:
1. Device is suprise removed.
2. Driver performs an MMIO, which fails and queues and eeh_event.
3. Hotplug driver receives a hotplug interrupt and removes any
pci_devs that were under the slot.
4. pci_dev is torn down and the eeh_pe is freed.
5. The EEH event handler thread processes the eeh_event and crashes
since the eeh_pe pointer in the eeh_event structure is no
longer valid.
Crashing is generally considered poor form. Instead of doing that use
the fact PEs are marked as EEH_PE_INVALID to keep them around until the
end of the recovery cycle, at which point we can safely prune any empty
PEs.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-2-oohall@gmail.com
CONFIG_SHELL falls back to sh when bash is not installed on the system,
but nobody is testing such a case since bash is usually installed.
So, shell scripts invoked by CONFIG_SHELL are only tested with bash.
It makes it difficult to test whether the hashbang #!/bin/sh is real.
For example, #!/bin/sh in arch/powerpc/kernel/prom_init_check.sh is
false. (I fixed it up)
Besides, some shell scripts invoked by CONFIG_SHELL use bash-extension
and #!/bin/bash is specified as the hashbang, while CONFIG_SHELL may
not always be set to bash.
Probably, the right thing to do is to introduce BASH, which is bash by
default, and always set CONFIG_SHELL to sh. Replace $(CONFIG_SHELL)
with $(BASH) for bash scripts.
If somebody tries to add bash-extension to a #!/bin/sh script, it will
be caught in testing because /bin/sh is a symlink to dash on some major
distributions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When in userspace and MSR FP=0 the hardware FP state is unrelated to
the current process. This is extended for transactions where if tbegin
is run with FP=0, the hardware checkpoint FP state will also be
unrelated to the current process. Due to this, we need to ensure this
hardware checkpoint is updated with the correct state before we enable
FP for this process.
Unfortunately we get this wrong when returning to a process from a
hardware interrupt. A process that starts a transaction with FP=0 can
take an interrupt. When the kernel returns back to that process, we
change to FP=1 but with hardware checkpoint FP state not updated. If
this transaction is then rolled back, the FP registers now contain the
wrong state.
The process looks like this:
Userspace: Kernel
Start userspace
with MSR FP=0 TM=1
< -----
...
tbegin
bne
Hardware interrupt
---- >
<do_IRQ...>
....
ret_from_except
restore_math()
/* sees FP=0 */
restore_fp()
tm_active_with_fp()
/* sees FP=1 (Incorrect) */
load_fp_state()
FP = 0 -> 1
< -----
Return to userspace
with MSR TM=1 FP=1
with junk in the FP TM checkpoint
TM rollback
reads FP junk
When returning from the hardware exception, tm_active_with_fp() is
incorrectly making restore_fp() call load_fp_state() which is setting
FP=1.
The fix is to remove tm_active_with_fp().
tm_active_with_fp() is attempting to handle the case where FP state
has been changed inside a transaction. In this case the checkpointed
and transactional FP state is different and hence we must restore the
FP state (ie. we can't do lazy FP restore inside a transaction that's
used FP). It's safe to remove tm_active_with_fp() as this case is
handled by restore_tm_state(). restore_tm_state() detects if FP has
been using inside a transaction and will set load_fp and call
restore_math() to ensure the FP state (checkpoint and transaction) is
restored.
This is a data integrity problem for the current process as the FP
registers are corrupted. It's also a security problem as the FP
registers from one process may be leaked to another.
Similarly for VMX.
A simple testcase to replicate this will be posted to
tools/testing/selftests/powerpc/tm/tm-poison.c
This fixes CVE-2019-15031.
Fixes: a7771176b4 ("powerpc: Don't enable FP/Altivec if not checkpointed")
Cc: stable@vger.kernel.org # 4.15+
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190904045529.23002-2-gromero@linux.vnet.ibm.com
When we take an FP unavailable exception in a transaction we have to
account for the hardware FP TM checkpointed registers being
incorrect. In this case for this process we know the current and
checkpointed FP registers must be the same (since FP wasn't used
inside the transaction) hence in the thread_struct we copy the current
FP registers to the checkpointed ones.
This copy is done in tm_reclaim_thread(). We use thread->ckpt_regs.msr
to determine if FP was on when in userspace. thread->ckpt_regs.msr
represents the state of the MSR when exiting userspace. This is setup
by check_if_tm_restore_required().
Unfortunatley there is an optimisation in giveup_all() which returns
early if tsk->thread.regs->msr (via local variable `usermsr`) has
FP=VEC=VSX=SPE=0. This optimisation means that
check_if_tm_restore_required() is not called and hence
thread->ckpt_regs.msr is not updated and will contain an old value.
This can happen if due to load_fp=255 we start a userspace process
with MSR FP=1 and then we are context switched out. In this case
thread->ckpt_regs.msr will contain FP=1. If that same process is then
context switched in and load_fp overflows, MSR will have FP=0. If that
process now enters a transaction and does an FP instruction, the FP
unavailable will not update thread->ckpt_regs.msr (the bug) and MSR
FP=1 will be retained in thread->ckpt_regs.msr. tm_reclaim_thread()
will then not perform the required memcpy and the checkpointed FP regs
in the thread struct will contain the wrong values.
The code path for this happening is:
Userspace: Kernel
Start userspace
with MSR FP/VEC/VSX/SPE=0 TM=1
< -----
...
tbegin
bne
fp instruction
FP unavailable
---- >
fp_unavailable_tm()
tm_reclaim_current()
tm_reclaim_thread()
giveup_all()
return early since FP/VMX/VSX=0
/* ckpt MSR not updated (Incorrect) */
tm_reclaim()
/* thread_struct ckpt FP regs contain junk (OK) */
/* Sees ckpt MSR FP=1 (Incorrect) */
no memcpy() performed
/* thread_struct ckpt FP regs not fixed (Incorrect) */
tm_recheckpoint()
/* Put junk in hardware checkpoint FP regs */
....
< -----
Return to userspace
with MSR TM=1 FP=1
with junk in the FP TM checkpoint
TM rollback
reads FP junk
This is a data integrity problem for the current process as the FP
registers are corrupted. It's also a security problem as the FP
registers from one process may be leaked to another.
This patch moves up check_if_tm_restore_required() in giveup_all() to
ensure thread->ckpt_regs.msr is updated correctly.
A simple testcase to replicate this will be posted to
tools/testing/selftests/powerpc/tm/tm-poison.c
Similarly for VMX.
This fixes CVE-2019-15030.
Fixes: f48e91e87e ("powerpc/tm: Fix FP and VMX register corruption")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190904045529.23002-1-gromero@linux.vnet.ibm.com
While the default ->mmap and ->get_sgtable implementations work for the
majority of our dma_map_ops impementations they are inherently safe
for others that don't use the page allocator or CMA and/or use their
own way of remapping not covered by the common code. So remove the
defaults if these methods are not wired up, but instead wire up the
default implementations for all safe instances.
Fixes: e1c7e32453 ("dma-mapping: always provide the dma_map_ops based implementation")
Signed-off-by: Christoph Hellwig <hch@lst.de>
This avoids 3 loads in the radix page fault case, 1 load in the
hash fault case, and 2 loads in the hash miss page fault case.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-37-npiggin@gmail.com
It is clever, but the small code saving is not worth the spaghetti of
jumping to a label in an expanded macro, particularly when the label
is just a number rather than a descriptive name.
So expand the INT_COMMON macro twice, once for the stack and no stack
cases, and branch to those. The slight code size increase is worth
the improved clarity of branches for this non-performance critical
code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-35-npiggin@gmail.com
This better reflects the order in which the code is executed.
No generated code change except BUG line number constants.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-34-npiggin@gmail.com
Move DAR and DSISR saving to pt_regs into INT_COMMON. Also add an
option to expand RECONCILE_IRQ_STATE.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-33-npiggin@gmail.com
Merge EXCEPTION_PROLOG_COMMON_3 into EXCEPTION_PROLOG_COMMON_2.
No generated code change except BUG line number constants.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-29-npiggin@gmail.com
Replace the 4 variants of cpp macros with one gas macro.
No generated code change except BUG line number constants.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-27-npiggin@gmail.com
All other virt handlers have the prolog code in the virt vector rather
than branch to the real vector. Follow this pattern in the denorm virt
handler.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-25-npiggin@gmail.com
EXCEPTION_PROLOG_0 and _1 have only a single caller, so expand them
into it.
Rename EXCEPTION_PROLOG_2_REAL to INT_SAVE_SRR_AND_JUMP and
EXCEPTION_PROLOG_2_VIRT to INT_VIRT_SAVE_SRR_AND_JUMP, which are
more descriptive.
No generated code change except BUG line number constants.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-24-npiggin@gmail.com
This creates a single macro that generates the exception prolog code,
with variants specified by arguments, rather than assorted nested
macros for different variants.
The increasing length of macro argument list is not nice to read or
modify, but this is a temporary condition that will be improved in
later changes.
No generated code change except BUG line number constants and label
names.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-23-npiggin@gmail.com
This vector is not used by any supported processor, and has been
implemented as an unknown exception going back to 2.6. There is
nothing special about 0xb00, so remove it like other unused
vectors.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-22-npiggin@gmail.com
The perf virt handler uses EXCEPTION_PROLOG_2_REAL rather than _VIRT.
In practice this is okay because the _REAL variant is usable by virt
mode interrupts, but should be fixed (and is a performance win).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-21-npiggin@gmail.com
Add EXC_HV_OR_STD and use it to consolidate the 0x500 external
interrupt.
Executed code is unchanged.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-20-npiggin@gmail.com
The head-64.h code should deal only with the head code sections
and offset calculations.
No generated code change except BUG line number constants.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-19-npiggin@gmail.com
This buglet goes back to before the 64/32 arch merge, but it does not
seem to have had practical consequences because bad_page_fault does
not use the 2nd argument, but rather regs->dar/nip.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-18-npiggin@gmail.com
Short forward and backward branches can be given number labels,
but larger significant divergences in code path a more readable
if they're given descriptive names.
Also adjusts a comment to account for guest delivery.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-17-npiggin@gmail.com
machine_check_early_common now branches to machine_check_handle_early
which is its only caller.
Move interleaving code out of the way, and remove the branch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-16-npiggin@gmail.com
Similarly to the previous change, all callers of the unrecoverable
handler run relocated so can reach it with a direct branch. This makes
it easy to move out of line, which makes the "normal" path less
cluttered and easier to follow.
MSR[ME] manipulation still requires the rfi, so that is moved out of
line to its own function.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-15-npiggin@gmail.com
machine_check_handle_early_common can reach machine_check_handle_early
directly now that it runs at the relocated address, so just branch
directly.
The rfi sequence is required to enable MSR[ME] but that step is moved
into a helper function, making the code easier to follow.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-14-npiggin@gmail.com
Following convention, move the tramp code (unrelocated) above the
common handlers (relocated).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-13-npiggin@gmail.com
Follow the pattern of sreset and HMI handlers more closely: use
EXCEPTION_PROLOG_COMMON_1 rather than open-coding it, and run the
handler at the relocated location.
This helps later simplification and code sharing.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-12-npiggin@gmail.com
The powernv machine check handler copes with taking a MCE from one of
three contexts, guest, kernel, and user. In each case the early
handler runs first on a special stack, then:
- The guest case branches to the KVM interrupt handler (via standard
interrupt macros).
- The user case will run the "late" handler which is like a normal
interrupt that runs in virtual mode and uses the regular kernel
stack.
- The kernel case queues the event and schedules it for processing
with irq work.
The last case is important, it must not enable virtual memory because
the MMU state may not be set up to deal with that (e.g., SLB might be
clear), it must not use the regular kernel stack for similar reasons
(e.g., might be in OPAL with OPAL stack in r1), and the kernel does
not expect anything to touch its stack if interrupts are disabled.
The pseries handler does not do this queueing, but instead it always
runs the late handler for host MCEs, which has some of the same
problems.
Now that pseries is using machine_check_events, change it to do the
same as powernv and queue events for kernel MCEs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-11-npiggin@gmail.com
The common machine_check_event data structures and queues are mostly
platform independent, with powernv decoding SRR1/DSISR/etc., into
machine_check_event objects.
This patch converts pseries to use this infrastructure by decoding
fwnmi/rtas data into machine_check_event objects.
This allows queueing to be used by a subsequent change to delay the
virtual mode handling of machine checks that occur in kernel space
where it is unsafe to switch immediately to virtual mode, similarly
to powernv.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix implicit fallthrough warnings in mce_handle_error()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-10-npiggin@gmail.com
Re-use the code introduced in pseries to save and dump the contents
of the SLB in the case of an SLB involved machine check exception.
This patch also avoids allocating the SLB save array on pseries radix.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-9-npiggin@gmail.com
Bare metal machine checks run an "early" handler in real mode before
running the main handler which reports the event.
The main handler runs exactly as a normal interrupt handler, after the
"windup" which sets registers back as they were at interrupt entry.
CFAR does not get restored by the windup code, so that will be wrong
when the handler is run.
Restore the CFAR to the saved value before running the late handler.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-8-npiggin@gmail.com
This label has only one caller, so unwind the branch and move it
inline. The location of the comment is adjusted to match similar
one in system reset.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-7-npiggin@gmail.com
Now that pseries with fwnmi registered runs the early machine check
handler, there is no good reason to special case the non-fwnmi case
and skip the early handler. Reducing the code and number of paths is
a top priority for asm code, it's better to handle this in C where
possible (and the pseries early handler is a no-op if fwnmi is not
registered).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-6-npiggin@gmail.com
The host kernel delivery case for powernv does RFI_TO_USER_OR_KERNEL,
but should just use RFI_TO_KERNEL which makes it clear this is not a
user case.
This is not a bug because RFI_TO_USER_OR_KERNEL deals with kernel
returns just fine.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-5-npiggin@gmail.com
The machine_check_handle_early hypervisor guest test is skipped if
!HVMODE or MSR[HV]=0, which is wrong for PR or nested hypervisors
that could be running a guest in this state.
Test HSTATE_IN_GUEST up front and use that to branch out to the KVM
handler, then MSR[PR] alone can test for this kernel's userspace.
This matches all other interrupt handling.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-4-npiggin@gmail.com
User space might want to know it's running in a secure VM. It can't do
a mfmsr because mfmsr is a privileged instruction.
The solution here is to create a cpu attribute:
/sys/devices/system/cpu/svm
which will read 0 or 1 based on the S bit of the current CPU.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820021326.6884-12-bauerman@linux.ibm.com
A new kernel deserves a clean slate. Any pages shared with the hypervisor
is unshared before invoking the new kernel. However there are exceptions.
If the new kernel is invoked to dump the current kernel, or if there is a
explicit request to preserve the state of the current kernel, unsharing
of pages is skipped.
NOTE: While testing crashkernel, make sure at least 256M is reserved for
crashkernel. Otherwise SWIOTLB allocation will fail and crash kernel will
fail to boot.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820021326.6884-11-bauerman@linux.ibm.com
LPPACA structures need to be shared with the host. Hence they need to be in
shared memory. Instead of allocating individual chunks of memory for a
given structure from memblock, a contiguous chunk of memory is allocated
and then converted into shared memory. Subsequent allocation requests will
come from the contiguous chunk which will be always shared memory for all
structures.
While we are able to use a kmem_cache constructor for the Debug Trace Log,
LPPACAs are allocated very early in the boot process (before SLUB is
available) so we need to use a simpler scheme here.
Introduce helper is_svm_platform() which uses the S bit of the MSR to tell
whether we're running as a secure guest.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820021326.6884-9-bauerman@linux.ibm.com
Helps document what the hard-coded number means.
Also take the opportunity to fix an #endif comment.
Suggested-by: Alexey Kardashevskiy <aik@linux.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820021326.6884-8-bauerman@linux.ibm.com
Make the Enter-Secure-Mode (ESM) ultravisor call to switch the VM to secure
mode. Pass kernel base address and FDT address so that the Ultravisor is
able to verify the integrity of the VM using information from the ESM blob.
Add "svm=" command line option to turn on switching to secure mode.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
[ andmike: Generate an RTAS os-term hcall when the ESM ucall fails. ]
Signed-off-by: Michael Anderson <andmike@linux.ibm.com>
[ bauerman: Cleaned up the code a bit. ]
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820021326.6884-5-bauerman@linux.ibm.com
Introduce CONFIG_PPC_SVM to control support for secure guests and include
Ultravisor-related helpers when it is selected
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820021326.6884-3-bauerman@linux.ibm.com
When an SVM makes an hypercall or incurs some other exception, the
Ultravisor usually forwards (a.k.a. reflects) the exceptions to the
Hypervisor. After processing the exception, Hypervisor uses the
UV_RETURN ultracall to return control back to the SVM.
The expected register state on entry to this ultracall is:
* Non-volatile registers are restored to their original values.
* If returning from an hypercall, register R0 contains the return value
(unlike other ultracalls) and, registers R4 through R12 contain any
output values of the hypercall.
* R3 contains the ultracall number, i.e UV_RETURN.
* If returning with a synthesized interrupt, R2 contains the
synthesized interrupt number.
Thanks to input from Paul Mackerras, Ram Pai and Mike Anderson.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Claudio Carvalho <cclaudio@linux.ibm.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190822034838.27876-8-cclaudio@linux.ibm.com
In PEF enabled systems, some of the resources which were previously
hypervisor privileged are now ultravisor privileged and controlled by
the ultravisor firmware.
This adds FW_FEATURE_ULTRAVISOR to indicate if PEF is enabled.
The host kernel can use FW_FEATURE_ULTRAVISOR, for instance, to skip
accessing resources (e.g. PTCR and LDBAR) in case PEF is enabled.
Signed-off-by: Claudio Carvalho <cclaudio@linux.ibm.com>
[ andmike: Device node name to "ibm,ultravisor" ]
Signed-off-by: Michael Anderson <andmike@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190822034838.27876-4-cclaudio@linux.ibm.com
The ultracalls (ucalls for short) allow the Secure Virtual Machines
(SVM)s and hypervisor to request services from the ultravisor such as
accessing a register or memory region that can only be accessed when
running in ultravisor-privileged mode.
This patch adds the ucall_norets() ultravisor call handler.
The specific service needed from an ucall is specified in register
R3 (the first parameter to the ucall). Other parameters to the
ucall, if any, are specified in registers R4 through R12.
Return value of all ucalls is in register R3. Other output values
from the ucall, if any, are returned in registers R4 through R12.
Each ucall returns specific error codes, applicable in the context
of the ucall. However, like with the PowerPC Architecture Platform
Reference (PAPR), if no specific error code is defined for a particular
situation, then the ucall will fallback to an erroneous
parameter-position based code. i.e U_PARAMETER, U_P2, U_P3 etc depending
on the ucall parameter that may have caused the error.
Every host kernel (powernv) needs to be able to do ucalls in case it
ends up being run in a machine with ultravisor enabled. Otherwise, the
kernel may crash early in boot trying to access ultravisor resources,
for instance, trying to set the partition table entry 0. Secure guests
also need to be able to do ucalls and its kernel may not have
CONFIG_PPC_POWERNV=y. For that reason, the ucall.S file is placed under
arch/powerpc/kernel.
If ultravisor is not enabled, the ucalls will be redirected to the
hypervisor which must handle/fail the call.
Thanks to inputs from Ram Pai and Michael Anderson.
Signed-off-by: Claudio Carvalho <cclaudio@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190822034838.27876-3-cclaudio@linux.ibm.com
Add the PowerPC name and the PPC_ELFNOTE_CAPABILITIES type in the
kernel binary ELF note. This type is a bitmap that can be used to
advertise kernel capabilities to userland.
This patch also defines PPCCAP_ULTRAVISOR_BIT as being the bit zero.
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Claudio Carvalho <cclaudio@linux.ibm.com>
[ maxiwell: Define the 'PowerPC' type in the elfnote.h ]
Signed-off-by: Maxiwell S. Garcia <maxiwell@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190829155021.2915-2-maxiwell@linux.ibm.com
As now we have xchg_no_kill/tce_kill, these are not used anymore so
remove them.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190829085252.72370-6-aik@ozlabs.ru
At the moment updates in a TCE table are made by iommu_table_ops::exchange
which update one TCE and invalidates an entry in the PHB/NPU TCE cache
via set of registers called "TCE Kill" (hence the naming).
Writing a TCE is a simple xchg() but invalidating the TCE cache is
a relatively expensive OPAL call. Mapping a 100GB guest with PCI+NPU
passed through devices takes about 20s.
Thankfully we can do better. Since such big mappings happen at the boot
time and when memory is plugged/onlined (i.e. not often), these requests
come in 512 pages so we call call OPAL 512 times less which brings 20s
from the above to less than 10s. Also, since TCE caches can be flushed
entirely, calling OPAL for 512 TCEs helps skiboot [1] to decide whether
to flush the entire cache or not.
This implements 2 new iommu_table_ops callbacks:
- xchg_no_kill() to update a single TCE with no TCE invalidation;
- tce_kill() to invalidate multiple TCEs.
This uses the same xchg_no_kill() callback for IODA1/2.
This implements 2 new wrappers on top of the new callbacks similar to
the existing iommu_tce_xchg().
This does not use the new callbacks yet, the next patches will;
so this should not cause any behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190829085252.72370-2-aik@ozlabs.ru
The existing code uses bunch of hardcoded values from the PCI Bus
Binding to IEEE Std 1275 spec; and it does so in quite non-obvious
way.
This defines fields from the cell#0 of the "reg" property of a PCI
device and uses them for parsing.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[mpe: Unsplit some 80/81 char lines, space the code with some newlines]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190829084417.71873-1-aik@ozlabs.ru
There is support for the kernel to execute the 'sc 0' instruction and
make a system call to itself. This is a relic that is unused in the
tree, therefore untested. It's also highly questionable for modules to
be doing this.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190827033010.28090-3-npiggin@gmail.com
Commit 3033f14ab7 ("clone: support passing tls argument via C rather
than pt_regs magic") introduced the HAVE_COPY_THREAD_TLS option. Use it
to avoid a subtle assumption about the argument ordering of clone type
syscalls.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190827033010.28090-2-npiggin@gmail.com
The code which fixups the DAR on TLB errors for dbcX instructions
has a self-modifying code alternative that has never been used.
Drop it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b095e12c82fcba1ac4c09fc3b85d969f36614746.1566417610.git.christophe.leroy@c-s.fr
Prior to commit 1bd98d7fbaf5 ("ppc64: Update BUG handling based on
ppc32"), BUG() family was using BUG_ILLEGAL_INSTRUCTION which
was an invalid instruction opcode to trap into program check
exception.
That commit converted them to using standard trap instructions,
but prom/prom_init and their PROM_BUG() macro were left over.
head_64.S and exception-64s.S were left aside as well.
Convert them to using the standard BUG infrastructure.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/cdaf4bbbb64c288a077845846f04b12683f8875a.1566817807.git.christophe.leroy@c-s.fr
Today LOAD_REG_IMMEDIATE() is a basic #define which loads all
parts on a value into a register, including the parts that are NUL.
This means always 2 instructions on PPC32 and always 5 instructions
on PPC64. And those instructions cannot run in parallele as they are
updating the same register.
Ex: LOAD_REG_IMMEDIATE(r1,THREAD_SIZE) in head_64.S results in:
3c 20 00 00 lis r1,0
60 21 00 00 ori r1,r1,0
78 21 07 c6 rldicr r1,r1,32,31
64 21 00 00 oris r1,r1,0
60 21 40 00 ori r1,r1,16384
Rewrite LOAD_REG_IMMEDIATE() with GAS macro in order to skip
the parts that are NUL.
Rename existing LOAD_REG_IMMEDIATE() as LOAD_REG_IMMEDIATE_SYM()
and use that one for loading value of symbols which are not known
at compile time.
Now LOAD_REG_IMMEDIATE(r1,THREAD_SIZE) in head_64.S results in:
38 20 40 00 li r1,16384
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/d60ce8dd3a383c7adbfc322bf1d53d81724a6000.1566311636.git.christophe.leroy@c-s.fr
ppc_md.ioremap() is only used for I/O workaround on CELL platform,
so indirect function call can be avoided.
This patch reworks the io-workaround and ioremap() functions to
use the global 'io_workaround_inited' flag for the activation
of io-workaround.
When CONFIG_PPC_IO_WORKAROUNDS or CONFIG_PPC_INDIRECT_MMIO are not
selected, the I/O workaround ioremap() voids and the global flag is
not used.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/5fa3ef069fbd0f152512afaae19e7a60161454cf.1566309262.git.christophe.leroy@c-s.fr
Add support for disabling the kernel implemented spectre v2 mitigation
(count cache flush on context switch) via the nospectre_v2 and
mitigations=off cmdline options.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christopher M. Riedl <cmr@informatik.wtf>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190524024647.381-1-cmr@informatik.wtf
We still treat devices without a DMA mask as defaulting to 32-bits for
both mask, but a few releases ago we've started warning about such
cases, as they require special cases to work around this sloppyness.
Add a dma_mask field to struct platform_device so that we can initialize
the dma_mask pointer in struct device and initialize both masks to
32-bits by default, replacing similar functionality in m68k and
powerpc. The arch_setup_pdev_archdata hooks is now unused and removed.
Note that the code looks a little odd with the various conditionals
because we have to support platform_device structures that are
statically allocated.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20190816062435.881-7-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a PCI device is removed during eeh_pe_report_edev(), between the
calls to device_lock() and device_unlock(), edev->pdev will change and
cause a crash as the wrong mutex is released.
To correct this, hold the PCI rescan/remove lock while taking a copy
of edev->pdev and performing a get_device() on it. Use this value to
release the mutex, but also pass it through to the device driver's EEH
handlers so that they always see the same device.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/3c590579a0faa24d20c826dcd26c739eb4d454e6.1565930772.git.sbobroff@linux.ibm.com
Convert existing messages, where appropriate, to use the eeh_edev_*
logging macros.
The only effect should be minor adjustments to the log messages, apart
from:
- A new message in pseries_eeh_probe() "Probing device" to match the
powernv case.
- The "Probing device" message in pnv_eeh_probe() is now generated
slightly later, which will mean that it is no longer emitted for
devices that aren't probed due to the initial checks.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ce505a0a7a4a5b0367f0f40f8b26e7c0a9cf4cb7.1565930772.git.sbobroff@linux.ibm.com
Now that struct eeh_dev includes the BDFN of it's PCI device, make use
of it to replace eeh_edev_info() with a set of dev_dbg()-style macros
that only need a struct edev.
With the BDFN available without the struct pci_dev, eeh_pci_name() is
now unnecessary, so remove it.
While only the "info" level function is used here, the others will be
used in followup work.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f90ae9a53d762be7b0ccbad79e62b5a1b4f4996e.1565930772.git.sbobroff@linux.ibm.com
Preparation for removing pci_dn from the powernv EEH code. The only
thing we really use pci_dn for is to get the bdfn of the device for
config space accesses, so adding that information to eeh_dev reduces
the need to carry around the pci_dn.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[SB: Re-wrapped commit message, fixed whitespace damage.]
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/e458eb69a1f591d8a120782f23a8506b15d3c654.1565930772.git.sbobroff@linux.ibm.com
Now that EEH support for all devices (on PowerNV and pSeries) is
provided by the pcibios bus add device hooks, eeh_probe_devices() and
eeh_addr_cache_build() are redundant and can be removed.
Move the EEH enabled message into it's own function so that it can be
called from multiple places.
Note that previously on pSeries, useless EEH sysfs files were created
for some devices that did not have EEH support and this change
prevents them from being created.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/33b0a6339d5ac88693de092d6fba984f2a5add66.1565930772.git.sbobroff@linux.ibm.com
On PowerNV and pSeries, devices currently acquire EEH support from
several different places: Boot-time devices from eeh_probe_devices()
and eeh_addr_cache_build(), Virtual Function devices from the pcibios
bus add device hooks and hot plugged devices from pci_hp_add_devices()
(with other platforms using other methods as well). Unfortunately,
pSeries machines currently discover hot plugged devices using
pci_rescan_bus(), not pci_hp_add_devices(), and so those devices do
not receive EEH support.
Rather than adding another case for pci_rescan_bus(), this change
widens the scope of the pcibios bus add device hooks so that they can
handle all devices. As a side effect this also supports devices
discovered after manually rescanning via /sys/bus/pci/rescan.
Note that on PowerNV, this change allows the EEH subsystem to become
enabled after boot as long as it has not been forced off, which was
not previously possible (it was already possible on pSeries).
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/72ae8ae9c54097158894a52de23690448de38ea9.1565930772.git.sbobroff@linux.ibm.com
The EEH address cache is currently initialized and populated by a
single function: eeh_addr_cache_build(). While the initial population
of the cache can only be done once resources are allocated,
initialization (just setting up a spinlock) could be done much
earlier.
So move the initialization step into a separate function and call it
from a core_initcall (rather than a subsys initcall).
This will allow future work to make use of the cache during boot time
PCI scanning.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0557206741bffee76cdfff042f65321f6f7a5b41.1565930772.git.sbobroff@linux.ibm.com
The EEH_DEV_NO_HANDLER flag is used by the EEH system to prevent the
use of driver callbacks in drivers that have been bound part way
through the recovery process. This is necessary to prevent later stage
handlers from being called when the earlier stage handlers haven't,
which can be confusing for drivers.
However, the flag is set for all devices that are added after boot
time and only cleared at the end of the EEH recovery process. This
results in hot plugged devices erroneously having the flag set during
the first recovery after they are added (causing their driver's
handlers to be incorrectly ignored).
To remedy this, clear the flag at the beginning of recovery
processing. The flag is still cleared at the end of recovery
processing, although it is no longer really necessary.
Also clear the flag during eeh_handle_special_event(), for the same
reasons.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b8ca5629d27de74c957d4f4b250177d1b6fc4bbd.1565930772.git.sbobroff@linux.ibm.com
The pcibios_init() function for PowerPC 64 currently calls
pci_bus_add_devices() before pcibios_resource_survey(). This means
that at boot time, when the pcibios_bus_add_device() hooks are called
by pci_bus_add_devices(), device resources have not been allocated and
they are unable to perform EEH setup, so a separate pass is needed.
This patch adjusts that order so that it will become possible to
consolidate the EEH setup work into a single location.
The only functional change is to execute pcibios_resource_survey()
(excepting ppc_md.pcibios_fixup(), see below) before
pci_bus_add_devices() instead of after it.
Because pcibios_scan_phb() and pci_bus_add_devices() are called
together in a loop, this must be broken into one loop for each call.
Then the call to pcibios_resource_survey() is moved up in between
them. This changes the ordering but because pcibios_resource_survey()
also calls ppc_md.pcibios_fixup(), that call is extracted out into
pcibios_init() to where pcibios_resource_survey() was, so that it is
not moved.
The only other caller of pcibios_resource_survey() is the PowerPC 32
version of pcibios_init(), and therefore, that is modified to call
ppc_md.pcibios_fixup() right after pcibios_resource_survey() so that
there is no functional change there at all.
The re-arrangement will cause very few side-effects because at this
stage in the boot, pci_bus_add_devices() does very little:
- pci_create_sysfs_dev_files() does nothing (no sysfs yet)
- pci_proc_attach_device() does nothing (no proc yet)
- device_attach() does nothing (no drivers yet)
This leaves only the pci_final_fixup calls, D3 support, and marking
the device as added. Of those, only the pci_final_fixup calls have the
potential to be affected by resource allocation.
The only pci_final_fixup handlers that touch resources seem to be one
for x86 (pci_amd_enable_64bit_bar()), and a PowerPC 32 platform driver
(quirk_final_uli1575()), neither of which use this pcibios_init()
function. Even if they did, it would almost certainly be a bug, under
the current ordering, to rely on or make changes to resources before
they were allocated.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4506b0489eabd0921a3587d90bd44c7683f3472d.1565930772.git.sbobroff@linux.ibm.com
If we take a UE on one of the instructions with a fixup entry, set nip
to continue execution at the fixup entry. Stop processing the event
further or print it.
Co-developed-by: Reza Arbab <arbab@linux.ibm.com>
Signed-off-by: Reza Arbab <arbab@linux.ibm.com>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820081352.8641-6-santosh@fossix.org
The function doesn't get used outside this file, so make it static.
Signed-off-by: Reza Arbab <arbab@linux.ibm.com>
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820081352.8641-4-santosh@fossix.org
The current code would fail on huge pages addresses, since the shift would
be incorrect. Use the correct page shift value returned by
__find_linux_pte() to get the correct physical address. The code is more
generic and can handle both regular and compound pages.
Fixes: ba41e1e1cc ("powerpc/mce: Hookup derror (load/store) UE errors")
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[arbab@linux.ibm.com: Fixup pseries_do_memory_failure()]
Signed-off-by: Reza Arbab <arbab@linux.ibm.com>
Tested-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820081352.8641-3-santosh@fossix.org
rtas_cpu_state_change_mask() potentially operates on scores of cpus,
so explicitly allow rescheduling in the loop body.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802192926.19277-3-nathanl@linux.ibm.com
The LPAR migration implementation and userspace-initiated cpu hotplug
can interleave their executions like so:
1. Set cpu 7 offline via sysfs.
2. Begin a partition migration, whose implementation requires the OS
to ensure all present cpus are online; cpu 7 is onlined:
rtas_ibm_suspend_me -> rtas_online_cpus_mask -> cpu_up
This sets cpu 7 online in all respects except for the cpu's
corresponding struct device; dev->offline remains true.
3. Set cpu 7 online via sysfs. _cpu_up() determines that cpu 7 is
already online and returns success. The driver core (device_online)
sets dev->offline = false.
4. The migration completes and restores cpu 7 to offline state:
rtas_ibm_suspend_me -> rtas_offline_cpus_mask -> cpu_down
This leaves cpu7 in a state where the driver core considers the cpu
device online, but in all other respects it is offline and
unused. Attempts to online the cpu via sysfs appear to succeed but the
driver core actually does not pass the request to the lower-level
cpuhp support code. This makes the cpu unusable until the cpu device
is manually set offline and then online again via sysfs.
Instead of directly calling cpu_up/cpu_down, the migration code should
use the higher-level device core APIs to maintain consistent state and
serialize operations.
Fixes: 120496ac2d ("powerpc: Bring all threads online prior to migration/hibernation")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802192926.19277-2-nathanl@linux.ibm.com
If a page is already mapped RW without the DIRTY flag, the DIRTY
flag is never set and a TLB store miss exception is taken forever.
This is easily reproduced with the following app:
void main(void)
{
volatile char *ptr = mmap(0, 4096, PROT_READ | PROT_WRITE, MAP_SHARED | MAP_ANONYMOUS, -1, 0);
*ptr = *ptr;
}
When DIRTY flag is not set, bail out of TLB miss handler and take
a minor page fault which will set the DIRTY flag.
Fixes: f8b58c64ea ("powerpc/603: let's handle PAGE_DIRTY directly")
Cc: stable@vger.kernel.org # v5.1+
Reported-by: Doug Crawford <doug.crawford@intelight-its.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/80432f71194d7ee75b2f5043ecf1501cf1cca1f3.1566196646.git.christophe.leroy@c-s.fr
copy_page() and clear_page() expect page aligned destination, and
use dcbz instruction to clear entire cache lines based on the
assumption that the destination is cache aligned.
As shown during analysis of a bug in BTRFS filesystem, a misaligned
copy_page() can create bugs that are difficult to locate (see Link).
Add an explicit WARNING when copy_page() or clear_page() are called
with misaligned destination.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204371
Link: https://lore.kernel.org/r/c6cea38f90480268d439ca44a645647e260fff09.1565941808.git.christophe.leroy@c-s.fr
When KASAN is selected, the definitive hash table has to be
set up later, but there is already an early temporary one.
When KASAN is not selected, there is no early hash table,
so the setup of the definitive hash table cannot be delayed.
Fixes: 72f208c6a8 ("powerpc/32s: move hash code patching out of MMU_init_hw()")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: Jonathan Neuschafer <j.neuschaefer@gmx.net>
Tested-by: Jonathan Neuschafer <j.neuschaefer@gmx.net>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b7860c5e1e784d6b96ba67edf47dd6cbc2e78ab6.1565776892.git.christophe.leroy@c-s.fr
On 8xx, breakpoints stop after executing the instruction, so
stepping/emulation is not needed. Move it into a sub-function and
remove the #ifdefs.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f8cdc3f1c66ad3c43ebc568abcc6c39ed4676284.1561737231.git.christophe.leroy@c-s.fr
At the moment we create a small window only for 32bit devices, the window
maps 0..2GB of the PCI space only. For other devices we either use
a sketchy bypass or hardware bypass but the former can only work if
the amount of RAM is no bigger than the device's DMA mask and the latter
requires devices to support at least 59bit DMA.
This extends the default DMA window to the maximum size possible to allow
a wider DMA mask than just 32bit. The default window size is now limited
by the the iommu_table::it_map allocation bitmap which is a contiguous
array, 1 bit per an IOMMU page.
This increases the default IOMMU page size from hard coded 4K to
the system page size to allow wider DMA masks.
This increases the level number to not exceed the max order allocation
limit per TCE level. By the same time, this keeps minimal levels number
as 2 in order to save memory.
As the extended window now overlaps the 32bit MMIO region, this adds
an area reservation to iommu_init_table().
After this change the default window size is 0x80000000000==1<<43 so
devices limited to DMA mask smaller than the amount of system RAM can
still use more than just 2GB of memory for DMA.
This is an optimization and not a bug fix for DMA API usage.
With the on-demand allocation of indirect TCE table levels enabled and
2 levels, the first TCE level size is just
1<<ceil((log2(0x7ffffffffff+1)-16)/2)=16384 TCEs or 2 system pages.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190718051139.74787-5-aik@ozlabs.ru
POWER8 and newer support a bypass mode which maps all host memory to
PCI buses so an IOMMU table is not always required. However if we fail to
create such a table, the DMA setup fails and the kernel does not boot.
This skips the 32bit DMA setup check if the bypass is selected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190718051139.74787-3-aik@ozlabs.ru
All the way back to introducing dma_common_mmap we've defaulted to mark
the pages as uncached. But this is wrong for DMA coherent devices.
Later on DMA_ATTR_WRITE_COMBINE also got incorrect treatment as that
flag is only treated special on the alloc side for non-coherent devices.
Introduce a new dma_pgprot helper that deals with the check for coherent
devices so that only the remapping cases ever reach arch_dma_mmap_pgprot
and we thus ensure no aliasing of page attributes happens, which makes
the powerpc version of arch_dma_mmap_pgprot obsolete and simplifies the
remaining ones.
Note that this means arch_dma_mmap_pgprot is a bit misnamed now, but
we'll phase it out soon.
Fixes: 64ccc9c033 ("common: dma-mapping: add support for generic dma_mmap_* calls")
Reported-by: Shawn Anastasio <shawn@anastas.io>
Reported-by: Gavin Li <git@thegavinli.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> # arm64
These aren't used by modular code, nor should they be.
Fixes: 120496ac2d ("powerpc: Bring all threads online prior to migration/hibernation")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190718162214.5694-1-nathanl@linux.ibm.com
Mark switch cases where we are expecting to fall through.
Fixes errors such as below, seen with mpc85xx_defconfig:
arch/powerpc/kernel/align.c: In function 'emulate_spe':
arch/powerpc/kernel/align.c:178:8: error: this statement may fall through
ret |= __get_user_inatomic(temp.v[3], p++);
^~
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190730141917.21817-1-mpe@ellerman.id.au
Wire up the new clone3 syscall added in commit 7f192e3cd3 ("fork:
add clone3").
This requires a ppc_clone3 wrapper, in order to save the non-volatile
GPRs before calling into the generic syscall code. Otherwise we hit
the BUG_ON in CHECK_FULL_REGS in copy_thread().
Lightly tested using Christian's test code on a Power8 LE VM.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Christian Brauner <christian@brauner.io>
Link: https://lore.kernel.org/r/20190724140259.23554-1-mpe@ellerman.id.au
from the massive RST conversion; a few other small fixes as well.
-----BEGIN PGP SIGNATURE-----
iQFCBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl07C9gPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YQrgH+L7kPaRWcH+lorh7WxiIhlAvqFsR4xjRKTZV
qZwlv3+87qjPu86DBdjRlos8PsoIkdD4+jH0u+7swYtZ5hsS8DYcfZ42i+nHqP7D
k/XwVPW71ikpoi4vQVsO9zrwaOKPyL8AoNzlj+VpiVGAu/PYApGUfdkdOD0xxlOW
hst6GKNAKrsoQ8fW3AIuCVi4oEEYru2FHMKLcpHBFDZtR7zgC4dEgs7UqEttAzHU
559nkH2LKekya4pQaFMdSb6Wgj+JeIkI2XzujXES6QEdmf8vrvjkkvHeByoOYjNY
NNdKNGhPUWrEUMfyzRQpEIcF+Dk3lYtBEDQO8+XCh6mpa9h7kQ==
=BUU+
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3-1' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"This is mostly a set of follow-on fixes from Mauro fixing various
fallout from the massive RST conversion; a few other small fixes as
well"
* tag 'docs-5.3-1' of git://git.lwn.net/linux: (21 commits)
docs: phy: Drop duplicate 'be made'
doc:it_IT: translations in process/
docs/vm: transhuge: fix typo in madvise reference
doc:it_IT: rephrase statement
doc:it_IT: align translation to mainline
docs: load_config.py: ensure subdirs end with "/"
docs: virtual: add it to the documentation body
docs: remove extra conf.py files
docs: load_config.py: avoid needing a conf.py just due to LaTeX docs
scripts/sphinx-pre-install: seek for Noto CJK fonts for pdf output
scripts/sphinx-pre-install: cleanup Gentoo checks
scripts/sphinx-pre-install: fix latexmk dependencies
scripts/sphinx-pre-install: don't use LaTeX with CentOS 7
scripts/sphinx-pre-install: fix script for RHEL/CentOS
docs: conf.py: only use CJK if the font is available
docs: conf.py: add CJK package needed by translations
docs: pdf: add all Documentation/*/index.rst to PDF output
docs: fix broken doc references due to renames
docs: power: add it to to the main documentation index
docs: powerpc: convert docs to ReST and rename to *.rst
...
An assortment of non-regression fixes that have accumulated since the start of
the merge window.
A fix for a user triggerable oops on machines where transactional memory is
disabled, eg. Power9 bare metal, Power8 with TM disabled on the command line, or
all Power7 or earlier machines.
Three fixes for handling of PMU and power saving registers when running nested
KVM on Power9.
Two fixes for bugs found while stress testing the XIVE interrupt controller
code, also on Power9.
A fix to allow guests to boot under Qemu/KVM on Power9 using the the Hash MMU
with >= 1TB of memory.
Two fixes for bugs in the recent DMA cleanup, one of which could lead to
checkstops.
And finally three fixes for the PAPR SCM nvdimm driver.
Thanks to:
Alexey Kardashevskiy, Andrea Arcangeli, Cédric Le Goater, Christoph Hellwig,
David Gibson, Gautham R. Shenoy, Michael Neuling, Oliver O'Halloran,, Satheesh
Rajendran, Shawn Anastasio, Suraj Jitindar Singh, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----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=Yc9T
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"An assortment of non-regression fixes that have accumulated since the
start of the merge window.
- A fix for a user triggerable oops on machines where transactional
memory is disabled, eg. Power9 bare metal, Power8 with TM disabled
on the command line, or all Power7 or earlier machines.
- Three fixes for handling of PMU and power saving registers when
running nested KVM on Power9.
- Two fixes for bugs found while stress testing the XIVE interrupt
controller code, also on Power9.
- A fix to allow guests to boot under Qemu/KVM on Power9 using the
the Hash MMU with >= 1TB of memory.
- Two fixes for bugs in the recent DMA cleanup, one of which could
lead to checkstops.
- And finally three fixes for the PAPR SCM nvdimm driver.
Thanks to: Alexey Kardashevskiy, Andrea Arcangeli, Cédric Le Goater,
Christoph Hellwig, David Gibson, Gautham R. Shenoy, Michael Neuling,
Oliver O'Halloran, Satheesh Rajendran, Shawn Anastasio, Suraj Jitindar
Singh, Vaibhav Jain"
* tag 'powerpc-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/papr_scm: Force a scm-unbind if initial scm-bind fails
powerpc/papr_scm: Update drc_pmem_unbind() to use H_SCM_UNBIND_ALL
powerpc/pseries: Update SCM hcall op-codes in hvcall.h
powerpc/tm: Fix oops on sigreturn on systems without TM
powerpc/dma: Fix invalid DMA mmap behavior
KVM: PPC: Book3S HV: XIVE: fix rollback when kvmppc_xive_create fails
powerpc/xive: Fix loop exit-condition in xive_find_target_in_mask()
powerpc: fix off by one in max_zone_pfn initialization for ZONE_DMA
KVM: PPC: Book3S HV: Save and restore guest visible PSSCR bits on pseries
powerpc/pmu: Set pmcregs_in_use in paca when running as LPAR
KVM: PPC: Book3S HV: Always save guest pmu for guest capable of nesting
powerpc/mm: Limit rma_size to 1TB when running without HV mode
On systems like P9 powernv where we have no TM (or P8 booted with
ppc_tm=off), userspace can construct a signal context which still has
the MSR TS bits set. The kernel tries to restore this context which
results in the following crash:
Unexpected TM Bad Thing exception at c0000000000022fc (msr 0x8000000102a03031) tm_scratch=800000020280f033
Oops: Unrecoverable exception, sig: 6 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 0 PID: 1636 Comm: sigfuz Not tainted 5.2.0-11043-g0a8ad0ffa4 #69
NIP: c0000000000022fc LR: 00007fffb2d67e48 CTR: 0000000000000000
REGS: c00000003fffbd70 TRAP: 0700 Not tainted (5.2.0-11045-g7142b497d8)
MSR: 8000000102a03031 <SF,VEC,VSX,FP,ME,IR,DR,LE,TM[E]> CR: 42004242 XER: 00000000
CFAR: c0000000000022e0 IRQMASK: 0
GPR00: 0000000000000072 00007fffb2b6e560 00007fffb2d87f00 0000000000000669
GPR04: 00007fffb2b6e728 0000000000000000 0000000000000000 00007fffb2b6f2a8
GPR08: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR12: 0000000000000000 00007fffb2b76900 0000000000000000 0000000000000000
GPR16: 00007fffb2370000 00007fffb2d84390 00007fffea3a15ac 000001000a250420
GPR20: 00007fffb2b6f260 0000000010001770 0000000000000000 0000000000000000
GPR24: 00007fffb2d843a0 00007fffea3a14a0 0000000000010000 0000000000800000
GPR28: 00007fffea3a14d8 00000000003d0f00 0000000000000000 00007fffb2b6e728
NIP [c0000000000022fc] rfi_flush_fallback+0x7c/0x80
LR [00007fffb2d67e48] 0x7fffb2d67e48
Call Trace:
Instruction dump:
e96a0220 e96a02a8 e96a0330 e96a03b8 394a0400 4200ffdc 7d2903a6 e92d0c00
e94d0c08 e96d0c10 e82d0c18 7db242a6 <4c000024> 7db243a6 7db142a6 f82d0c18
The problem is the signal code assumes TM is enabled when
CONFIG_PPC_TRANSACTIONAL_MEM is enabled. This may not be the case as
with P9 powernv or if `ppc_tm=off` is used on P8.
This means any local user can crash the system.
Fix the problem by returning a bad stack frame to the user if they try
to set the MSR TS bits with sigreturn() on systems where TM is not
supported.
Found with sigfuz kernel selftest on P9.
This fixes CVE-2019-13648.
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9
Reported-by: Praveen Pandey <Praveen.Pandey@in.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190719050502.405-1-mikey@neuling.org
The refactor of powerpc DMA functions in commit 6666cc17d7
("powerpc/dma: remove dma_nommu_mmap_coherent") incorrectly
changes the way DMA mappings are handled on powerpc.
Since this change, all mapped pages are marked as cache-inhibited
through the default implementation of arch_dma_mmap_pgprot.
This differs from the previous behavior of only marking pages
in noncoherent mappings as cache-inhibited and has resulted in
sporadic system crashes in certain hardware configurations and
workloads (see Bugzilla).
This commit restores the previous correct behavior by providing
an implementation of arch_dma_mmap_pgprot that only marks
pages in noncoherent mappings as cache-inhibited. As this behavior
should be universal for all powerpc platforms a new file,
dma-generic.c, was created to store it.
Fixes: 6666cc17d7 ("powerpc/dma: remove dma_nommu_mmap_coherent")
# NOTE: fixes commit 6666cc17d7 released in v5.1.
# Consider a stable tag:
# Cc: stable@vger.kernel.org # v5.1+
# NOTE: fixes commit 6666cc17d7 released in v5.1.
# Consider a stable tag:
# Cc: stable@vger.kernel.org # v5.1+
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Shawn Anastasio <shawn@anastas.io>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190717235437.12908-1-shawn@anastas.io
Convert docs to ReST and add them to the arch-specific
book.
The conversion here was trivial, as almost every file there
was already using an elegant format close to ReST standard.
The changes were mostly to mark literal blocks and add a few
missing section title identifiers.
One note with regards to "--": on Sphinx, this can't be used
to identify a list, as it will format it badly. This can be
used, however, to identify a long hyphen - and "---" is an
even longer one.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> # cxl
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXSxgkQAKCRCRxhvAZXjc
opJ3AP9TWIWhEC0dzbNmzh0STj/Vyl5KYEpdMbi7HNeAmIEAfQD6A3HI4bVJbN08
jH44U7DLzHJyHefKlB8jHEKEVYJWqgo=
=74Bg
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190715' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd and clone3 fixes from Christian Brauner:
"This contains a bugfix for CLONE_PIDFD when used with the legacy clone
syscall, two fixes to ensure that syscall numbering and clone3
entrypoint implementations will stay consistent, and an update for the
maintainers file:
- The addition of clone3 broke CLONE_PIDFD for legacy clone on all
architectures that use do_fork() directly instead of calling the
clone syscall itself. (Fwiw, cleaning do_fork() up is on my todo.)
The reason this happened was that during conversion of _do_fork()
to use struct kernel_clone_args we missed that do_fork() is called
directly by various architectures. This is fixed by making sure
that the pidfd argument in struct kernel_clone_args is correctly
initialized with the parent_tidptr argument passed down from
do_fork(). Additionally, do_fork() missed a check to make
CLONE_PIDFD and CLONE_PARENT_SETTID mutually exclusive just a
clone() does. This is now fixed too.
- When clone3() was introduced we skipped architectures that require
special handling for fork-like syscalls. Their syscall tables did
not contain any mention of clone3().
To make sure that Arnd's work to make syscall numbers on all
architectures identical (minus alpha) was not for naught we are
placing a comment in all syscall tables that do not yet implement
clone3(). The comment makes it clear that 435 is reserved for
clone3 and should not be used.
- Also, this contains a patch to make the clone3() syscall definition
in asm-generic/unist.h conditional on __ARCH_WANT_SYS_CLONE3. This
lets us catch new architectures that implicitly make use of clone3
without setting __ARCH_WANT_SYS_CLONE3 which is a good indicator
that they did not check whether it needs special treatment or not.
- Finally, this contains a patch to add me as maintainer for pidfd
stuff so people can start blaming me (more)"
* tag 'for-linus-20190715' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
MAINTAINERS: add new entry for pidfd api
unistd: protect clone3 via __ARCH_WANT_SYS_CLONE3
arch: mark syscall number 435 reserved for clone3
clone: fix CLONE_PIDFD support
Notable changes:
- Removal of the NPU DMA code, used by the out-of-tree Nvidia driver, as well
as some other functions only used by drivers that haven't (yet?) made it
upstream.
- A fix for a bug in our handling of hardware watchpoints (eg. perf record -e
mem: ...) which could lead to register corruption and kernel crashes.
- Enable HAVE_ARCH_HUGE_VMAP, which allows us to use large pages for vmalloc
when using the Radix MMU.
- A large but incremental rewrite of our exception handling code to use gas
macros rather than multiple levels of nested CPP macros.
And the usual small fixes, cleanups and improvements.
Thanks to:
Alastair D'Silva, Alexey Kardashevskiy, Andreas Schwab, Aneesh Kumar K.V, Anju
T Sudhakar, Anton Blanchard, Arnd Bergmann, Athira Rajeev, Cédric Le Goater,
Christian Lamparter, Christophe Leroy, Christophe Lombard, Christoph Hellwig,
Daniel Axtens, Denis Efremov, Enrico Weigelt, Frederic Barrat, Gautham R.
Shenoy, Geert Uytterhoeven, Geliang Tang, Gen Zhang, Greg Kroah-Hartman, Greg
Kurz, Gustavo Romero, Krzysztof Kozlowski, Madhavan Srinivasan, Masahiro
Yamada, Mathieu Malaterre, Michael Neuling, Nathan Lynch, Naveen N. Rao,
Nicholas Piggin, Nishad Kamdar, Oliver O'Halloran, Qian Cai, Ravi Bangoria,
Sachin Sant, Sam Bobroff, Satheesh Rajendran, Segher Boessenkool, Shaokun
Zhang, Shawn Anastasio, Stewart Smith, Suraj Jitindar Singh, Thiago Jung
Bauermann, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=3dBZ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Removal of the NPU DMA code, used by the out-of-tree Nvidia driver,
as well as some other functions only used by drivers that haven't
(yet?) made it upstream.
- A fix for a bug in our handling of hardware watchpoints (eg. perf
record -e mem: ...) which could lead to register corruption and
kernel crashes.
- Enable HAVE_ARCH_HUGE_VMAP, which allows us to use large pages for
vmalloc when using the Radix MMU.
- A large but incremental rewrite of our exception handling code to
use gas macros rather than multiple levels of nested CPP macros.
And the usual small fixes, cleanups and improvements.
Thanks to: Alastair D'Silva, Alexey Kardashevskiy, Andreas Schwab,
Aneesh Kumar K.V, Anju T Sudhakar, Anton Blanchard, Arnd Bergmann,
Athira Rajeev, Cédric Le Goater, Christian Lamparter, Christophe
Leroy, Christophe Lombard, Christoph Hellwig, Daniel Axtens, Denis
Efremov, Enrico Weigelt, Frederic Barrat, Gautham R. Shenoy, Geert
Uytterhoeven, Geliang Tang, Gen Zhang, Greg Kroah-Hartman, Greg Kurz,
Gustavo Romero, Krzysztof Kozlowski, Madhavan Srinivasan, Masahiro
Yamada, Mathieu Malaterre, Michael Neuling, Nathan Lynch, Naveen N.
Rao, Nicholas Piggin, Nishad Kamdar, Oliver O'Halloran, Qian Cai, Ravi
Bangoria, Sachin Sant, Sam Bobroff, Satheesh Rajendran, Segher
Boessenkool, Shaokun Zhang, Shawn Anastasio, Stewart Smith, Suraj
Jitindar Singh, Thiago Jung Bauermann, YueHaibing"
* tag 'powerpc-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (163 commits)
powerpc/powernv/idle: Fix restore of SPRN_LDBAR for POWER9 stop state.
powerpc/eeh: Handle hugepages in ioremap space
ocxl: Update for AFU descriptor template version 1.1
powerpc/boot: pass CONFIG options in a simpler and more robust way
powerpc/boot: add {get, put}_unaligned_be32 to xz_config.h
powerpc/irq: Don't WARN continuously in arch_local_irq_restore()
powerpc/module64: Use symbolic instructions names.
powerpc/module32: Use symbolic instructions names.
powerpc: Move PPC_HA() PPC_HI() and PPC_LO() to ppc-opcode.h
powerpc/module64: Fix comment in R_PPC64_ENTRY handling
powerpc/boot: Add lzo support for uImage
powerpc/boot: Add lzma support for uImage
powerpc/boot: don't force gzipped uImage
powerpc/8xx: Add microcode patch to move SMC parameter RAM.
powerpc/8xx: Use IO accessors in microcode programming.
powerpc/8xx: replace #ifdefs by IS_ENABLED() in microcode.c
powerpc/8xx: refactor programming of microcode CPM params.
powerpc/8xx: refactor printing of microcode patch name.
powerpc/8xx: Refactor microcode write
powerpc/8xx: refactor writing of CPM microcode arrays
...
In commit 4a7b06c157a2 ("powerpc/eeh: Handle hugepages in ioremap
space") support for using hugepages in the vmalloc and ioremap areas was
enabled for radix. Unfortunately this broke EEH MMIO error checking.
Detection works by inserting a hook which checks the results of the
ioreadXX() set of functions. When a read returns a 0xFFs response we
need to check for an error which we do by mapping the (virtual) MMIO
address back to a physical address, then mapping physical address to a
PCI device via an interval tree.
When translating virt -> phys we currently assume the ioremap space is
only populated by PAGE_SIZE mappings. If a hugepage mapping is found we
emit a WARN_ON(), but otherwise handles the check as though a normal
page was found. In pathalogical cases such as copying a buffer
containing a lot of 0xFFs from BAR memory this can result in the system
not booting because it's too busy printing WARN_ON()s.
There's no real reason to assume huge pages can't be present and we're
prefectly capable of handling them, so do that.
Fixes: 4a7b06c157a2 ("powerpc/eeh: Handle hugepages in ioremap space")
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190710150517.27114-1-oohall@gmail.com
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXSMhUgAKCRCRxhvAZXjc
okkiAQC3Hlg/O2JoIb4PqgEvBkpHSdVxyuWagn0ksjACW9ANKQEAl5OadMhvOq16
UHGhKlpE/M8HflknIffoEGlIAWHrdwU=
=7kP5
-----END PGP SIGNATURE-----
Merge tag 'pidfd-updates-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd updates from Christian Brauner:
"This adds two main features.
- First, it adds polling support for pidfds. This allows process
managers to know when a (non-parent) process dies in a race-free
way.
The notification mechanism used follows the same logic that is
currently used when the parent of a task is notified of a child's
death. With this patchset it is possible to put pidfds in an
{e}poll loop and get reliable notifications for process (i.e.
thread-group) exit.
- The second feature compliments the first one by making it possible
to retrieve pollable pidfds for processes that were not created
using CLONE_PIDFD.
A lot of processes get created with traditional PID-based calls
such as fork() or clone() (without CLONE_PIDFD). For these
processes a caller can currently not create a pollable pidfd. This
is a problem for Android's low memory killer (LMK) and service
managers such as systemd.
Both patchsets are accompanied by selftests.
It's perhaps worth noting that the work done so far and the work done
in this branch for pidfd_open() and polling support do already see
some adoption:
- Android is in the process of backporting this work to all their LTS
kernels [1]
- Service managers make use of pidfd_send_signal but will need to
wait until we enable waiting on pidfds for full adoption.
- And projects I maintain make use of both pidfd_send_signal and
CLONE_PIDFD [2] and will use polling support and pidfd_open() too"
[1] https://android-review.googlesource.com/q/topic:%22pidfd+polling+support+4.9+backport%22https://android-review.googlesource.com/q/topic:%22pidfd+polling+support+4.14+backport%22https://android-review.googlesource.com/q/topic:%22pidfd+polling+support+4.19+backport%22
[2] aab6e3eb73/src/lxc/start.c (L1753)
* tag 'pidfd-updates-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
tests: add pidfd_open() tests
arch: wire-up pidfd_open()
pid: add pidfd_open()
pidfd: add polling selftests
pidfd: add polling support
When CONFIG_PPC_IRQ_SOFT_MASK_DEBUG is enabled (uncommon), we have a
series of WARN_ON's in arch_local_irq_restore().
These are "should never happen" conditions, but if they do happen they
can flood the console and render the system unusable. So switch them
to WARN_ON_ONCE().
Fixes: e2b36d5917 ("powerpc/64: Don't trace code that runs with the soft irq mask unreconciled")
Fixes: 9b81c0211c ("powerpc/64s: make PACA_IRQ_HARD_DIS track MSR[EE] closely")
Fixes: 7c0482e3d0 ("powerpc/irq: Fix another case of lazy IRQ state getting out of sync")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190708061046.7075-1-mpe@ellerman.id.au
- Improve the handling of shared ACPI power resources in the PCI
bus type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec
into account as appropriate and avoid polling devices in D3cold
for PME (Mika Westerberg).
- Fix some corner case issues in ACPI device power management and
in the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210,
and armada-37xx cpufreq drivers (David Arcari, Florian Fainelli,
Paweł Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black).
-----BEGIN PGP SIGNATURE-----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=aBN3
-----END PGP SIGNATURE-----
Merge tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update PCI and ACPI power management (improved handling of ACPI
power resources and PCIe link delays, fixes related to corner cases,
hibernation handling rework), fix and extend the operating performance
points (OPP) framework, add new cpufreq drivers for Raspberry Pi and
imx8m chips, update some other cpufreq drivers, clean up assorted
pieces of PM code and documentation and update tools.
Specifics:
- Improve the handling of shared ACPI power resources in the PCI bus
type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec into
account as appropriate and avoid polling devices in D3cold for PME
(Mika Westerberg).
- Fix some corner case issues in ACPI device power management and in
the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210, and
armada-37xx cpufreq drivers (David Arcari, Florian Fainelli, Paweł
Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black)"
* tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (57 commits)
ACPI: PM: Make acpi_sleep_state_supported() non-static
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Unexport acpi_device_get_power()
Documentation: ABI: power: Add missing newline at end of file
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
cpufreq: Avoid calling cpufreq_verify_current_freq() from handle_update()
cpufreq: Consolidate cpufreq_update_current_freq() and __cpufreq_get()
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
cpufreq: Don't skip frequency validation for has_target() drivers
PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete()
PCI / ACPI: Add _PR0 dependent devices
ACPI / PM: Introduce concept of a _PR0 dependent device
PCI / ACPI: Use cached ACPI device state to get PCI device power state
ACPI: PM: Allow transitions to D0 to occur in special cases
ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold
cpufreq: Use has_target() instead of !setpolicy
...
Pull force_sig() argument change from Eric Biederman:
"A source of error over the years has been that force_sig has taken a
task parameter when it is only safe to use force_sig with the current
task.
The force_sig function is built for delivering synchronous signals
such as SIGSEGV where the userspace application caused a synchronous
fault (such as a page fault) and the kernel responded with a signal.
Because the name force_sig does not make this clear, and because the
force_sig takes a task parameter the function force_sig has been
abused for sending other kinds of signals over the years. Slowly those
have been fixed when the oopses have been tracked down.
This set of changes fixes the remaining abusers of force_sig and
carefully rips out the task parameter from force_sig and friends
making this kind of error almost impossible in the future"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (27 commits)
signal/x86: Move tsk inside of CONFIG_MEMORY_FAILURE in do_sigbus
signal: Remove the signal number and task parameters from force_sig_info
signal: Factor force_sig_info_to_task out of force_sig_info
signal: Generate the siginfo in force_sig
signal: Move the computation of force into send_signal and correct it.
signal: Properly set TRACE_SIGNAL_LOSE_INFO in __send_signal
signal: Remove the task parameter from force_sig_fault
signal: Use force_sig_fault_to_task for the two calls that don't deliver to current
signal: Explicitly call force_sig_fault on current
signal/unicore32: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from ptrace_break
signal/nds32: Remove tsk parameter from send_sigtrap
signal/riscv: Remove tsk parameter from do_trap
signal/sh: Remove tsk parameter from force_sig_info_fault
signal/um: Remove task parameter from send_sigtrap
signal/x86: Remove task parameter from send_sigtrap
signal: Remove task parameter from force_sig_mceerr
signal: Remove task parameter from force_sig
signal: Remove task parameter from force_sigsegv
...
Pull SMP/hotplug updates from Thomas Gleixner:
"A small set of updates for SMP and CPU hotplug:
- Abort disabling secondary CPUs in the freezer when a wakeup is
pending instead of evaluating it only after all CPUs have been
offlined.
- Remove the shared annotation for the strict per CPU cfd_data in the
smp function call core code.
- Remove the return values of smp_call_function() and on_each_cpu()
as they are unconditionally 0. Fixup the few callers which actually
bothered to check the return value"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp: Remove smp_call_function() and on_each_cpu() return values
smp: Do not mark call_function_data as shared
cpu/hotplug: Abort disabling secondary CPUs if wakeup is pending
cpu/hotplug: Fix notify_cpu_starting() reference in bringup_wait_for_ap()
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new XAFLAG
and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the 'arm_boot_flags'
introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
-----BEGIN PGP SIGNATURE-----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=0TDT
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new
XAFLAG and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the
'arm_boot_flags' introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
perf: arm_spe: Enable ACPI/Platform automatic module loading
arm_pmu: acpi: spe: Add initial MADT/SPE probing
ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens
ACPI/PPTT: Modify node flag detection to find last IDENTICAL
x86/entry: Simplify _TIF_SYSCALL_EMU handling
arm64: rename dump_instr as dump_kernel_instr
arm64/mm: Drop [PTE|PMD]_TYPE_FAULT
arm64: Implement panic_smp_self_stop()
arm64: Improve parking of stopped CPUs
arm64: Expose FRINT capabilities to userspace
arm64: Expose ARMv8.5 CondM capability to userspace
arm64: defconfig: enable CONFIG_RANDOMIZE_BASE
arm64: ARM64_MODULES_PLTS must depend on MODULES
arm64: bpf: do not allocate executable memory
arm64/kprobes: set VM_FLUSH_RESET_PERMS on kprobe instruction pages
arm64/mm: wire up CONFIG_ARCH_HAS_SET_DIRECT_MAP
arm64: module: create module allocations without exec permissions
arm64: Allow user selection of ARM64_MODULE_PLTS
acpi/arm64: ignore 5.1 FADTs that are reported as 5.0
arm64: Allow selecting Pseudo-NMI again
...
* pm-sleep:
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
PM: sleep: Update struct wakeup_source documentation
drivers: base: power: remove wakeup_sources_stats_dentry variable
PM: suspend: Rename pm_suspend_via_s2idle()
PM: sleep: Show how long dpm_suspend_start() and dpm_suspend_end() take
PM: hibernate: powerpc: Expose pfn_is_nosave() prototype
To increase readability/maintainability, replace hard coded
instructions values by symbolic names.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Fix R_PPC64_ENTRY case, the addi reads from r2 not r12]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To increase readability/maintainability, replace hard coded
instructions values by symbolic names.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PPC_HA() PPC_HI() and PPC_LO() macros are nice macros. Move them
from module64.c to ppc-opcode.h in order to use them in other places.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Clean up formatting in new code, drop duplicates in ftrace.c]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The comment here is wrong, the addi reads from r2 not r12. The code is
correct, 0x38420000 = addi r2,r2,0.
Fixes: a61674bdfc ("powerpc/module: Handle R_PPC64_ENTRY relocations")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On most arches having function flush_dcache_range(), including PPC32,
this function does a writeback and invalidation of the cache bloc.
On PPC64, flush_dcache_range() only does a writeback while
flush_inval_dcache_range() does the invalidation in addition.
In addition it looks like within arch/powerpc/, there are no PPC64
platforms using flush_dcache_range()
This patch drops the existing 64 bits version of flush_dcache_range()
and renames flush_inval_dcache_range() into flush_dcache_range().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pseries platform uses the PCI_PROBE_DEVTREE method of PCI probing
which reads "assigned-addresses" of every PCI device and initializes
the device resources. However if the property is missing or zero sized,
then there is no fallback of any kind and the PCI resources remain
undiscovered, i.e. pdev->resource[] array remains empty.
This adds a fallback which parses the "reg" property in pretty much same
way except it marks resources as "unset" which later make Linux assign
those resources proper addresses.
This has an effect when:
1. a hypervisor failed to assign any resource for a device;
2. /chosen/linux,pci-probe-only=0 is in the DT so the system may try
assigning a resource.
Neither is likely to happen under PowerVM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The commit 8617a5c5bc ("powerpc/dma: handle iommu bypass in
dma_iommu_ops") merged direct DMA ops into the IOMMU DMA ops allowing
SWIOTLB as well but only for mapping; the unmapping and bouncing parts
were left unmodified.
This adds missing direct unmapping calls to .unmap_page() and
.unmap_sg().
This adds missing sync callbacks and directs them to the direct DMA
hooks.
Fixes: 8617a5c5bc ("powerpc/dma: handle iommu bypass in dma_iommu_ops")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the dma_get_mask() helper from dma-mapping.h instead, as they are
functionally identical.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If you compile with KVM but without CONFIG_HAVE_HW_BREAKPOINT you fail
at linking with:
arch/powerpc/kvm/book3s_hv_rmhandlers.o:(.text+0x708): undefined reference to `dawr_force_enable'
This was caused by commit c1fe190c06 ("powerpc: Add force enable of
DAWR on P9 option").
This moves a bunch of code around to fix this. It moves a lot of the
DAWR code in a new file and creates a new CONFIG_PPC_DAWR to enable
compiling it.
Fixes: c1fe190c06 ("powerpc: Add force enable of DAWR on P9 option")
Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Minor formatting in set_dawr()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit c1fe190c06 ("powerpc: Add force enable of DAWR on P9
option") the following piece of code was added:
smp_call_function((smp_call_func_t)set_dawr, &null_brk, 0);
Since GCC 8 this triggers the following warning about incompatible
function types:
arch/powerpc/kernel/hw_breakpoint.c:408:21: error: cast between incompatible function types from 'int (*)(struct arch_hw_breakpoint *)' to 'void (*)(void *)' [-Werror=cast-function-type]
Since the warning is there for a reason, and should not be hidden behind
a cast, provide an intermediate callback function to avoid the warning.
Fixes: c1fe190c06 ("powerpc: Add force enable of DAWR on P9 option")
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This makes it clear to the caller that it can only be used on POWER9
and later CPUs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Use "ISA_3_0" rather than "ARCH_300"]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Branch to the relocated 0xc000 address early (still in real mode), to
simplify subsequent branches. Have the virt mode handler avoid just
'windup' and redo the exception from scratch, rather than branching
back to the trampoline.
Rearrange the stack setup instruction location to match the system
reset handler (e.g., right before EXCEPTION_PROLOG_COMMON).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Follow convention and move tramp ahead of common.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The idle wake up code in the system reset interrupt is not very
optimal. There are two requirements: perform idle wake up quickly;
and save everything including CFAR for non-idle interrupts, with
no performance requirement.
The problem with placing the idle test in the middle of the handler
and using the normal handler code to save CFAR, is that it's quite
costly (e.g., mfcfar is serialising, speculative workarounds get
applied, SRR1 has to be reloaded, etc). It also prevents the standard
interrupt handler boilerplate being used.
This pain can be avoided by using a dedicated idle interrupt handler
at the start of the interrupt handler, which restores all registers
back to the way they were in case it was not an idle wake up. CFAR
is preserved without saving it before the non-idle case by making that
the fall-through, and idle is a taken branch.
Performance seems to be in the noise, but possibly around 0.5% faster,
the executed instructions certainly look better. The bigger benefit is
being able to drop in standard interrupt handlers after the idle code,
which helps with subsequent cleanup and consolidation.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fixup BE by using DOTSYM for idle_return_gpr_loss call]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The bad stack test in interrupt handlers has a few problems. For
performance it is taken in the common case, which is a fetch bubble
and a waste of i-cache.
For code development and maintainence, it requires yet another stack
frame setup routine, and that constrains all exception handlers to
follow the same register save pattern which inhibits future
optimisation.
Remove the test/branch and replace it with a trap. Teach the program
check handler to use the emergency stack for this case.
This does not result in quite so nice a message, however the SRR0 and
SRR1 of the crashed interrupt can be seen in r11 and r12, as is the
original r1 (adjusted by INT_FRAME_SIZE). These are the most important
parts to debugging the issue.
The original r9-12 and cr0 is lost, which is the main downside.
kernel BUG at linux/arch/powerpc/kernel/exceptions-64s.S:847!
Oops: Exception in kernel mode, sig: 5 [#1]
BE SMP NR_CPUS=2048 NUMA PowerNV
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted
NIP: c000000000009108 LR: c000000000cadbcc CTR: c0000000000090f0
REGS: c0000000fffcbd70 TRAP: 0700 Not tainted
MSR: 9000000000021032 <SF,HV,ME,IR,DR,RI> CR: 28222448 XER: 20040000
CFAR: c000000000009100 IRQMASK: 0
GPR00: 000000000000003d fffffffffffffd00 c0000000018cfb00 c0000000f02b3166
GPR04: fffffffffffffffd 0000000000000007 fffffffffffffffb 0000000000000030
GPR08: 0000000000000037 0000000028222448 0000000000000000 c000000000ca8de0
GPR12: 9000000002009032 c000000001ae0000 c000000000010a00 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: c0000000f00322c0 c000000000f85200 0000000000000004 ffffffffffffffff
GPR24: fffffffffffffffe 0000000000000000 0000000000000000 000000000000000a
GPR28: 0000000000000000 0000000000000000 c0000000f02b391c c0000000f02b3167
NIP [c000000000009108] decrementer_common+0x18/0x160
LR [c000000000cadbcc] .vsnprintf+0x3ec/0x4f0
Call Trace:
Instruction dump:
996d098a 994d098b 38610070 480246ed 48005518 60000000 38200000 718a4000
7c2a0b78 3821fd00 41c20008 e82d0970 <0981fd00> f92101a0 f9610170 f9810178
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the system reset interrupt began to use its own stack, and
machine check interrupts have done so for some time, r1 can be
changed without clearing MSR[RI], provided no other interrupts
(including SLB misses) are taken.
MSR[RI] does have to be cleared when using SCRATCH0, however.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Although the 0x1500 interrupt only applies to bare metal, it is better
to just use the standard macro for scratch save.
Runtime code path remains unchanged (due to instruction patching).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Restore all SPRs and CR up-front, these are longer latency
instructions. Move register restore around to maximise pairs of
adjacent loads (e.g., restore r0 next to r1).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Duplicate the hmi windup code for both cases, rather than to put a
special case branch in the middle of it. Remove unused label. This
helps with later code consolidation.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move in_mce decrement earlier before registers are restored (but
still after RI=0). This helps with later consolidation.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All supported 64s CPUs support mtmsrd L=1 instruction, so a cleanup
can be made in sreset and mce handlers.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move SPR reads ahead of writes. Real mode entry that is not a KVM
guest is rare these days, but bad practice propagates.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
syscall / hcall entry unnecessarily differs between KVM and non-KVM
builds. Move the SMT priority instruction to the same location
(after INTERRUPT_TO_KERNEL).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No generated code change. Final vmlinux is changed only due to change
in bug table line numbers.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Generally, macros that result in instructions being expanded are
indented by a tab, and those that don't have no indent. Fix the
obvious cases that go contrary to style.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After the previous cleanup, it becomes possible to consolidate some
common code outside the runtime alternate patching. Also remove
unused labels.
This results in some code change, but unchanged runtime instruction
sequence.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Many of these macros just specify 1-4 lines which are only called a
few times each at most, and often just once. Remove this indirection.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
More cases of code insertion via macros that does not add a great
deal. All the additions have to be specified in the macro arguments,
so they can just as well go after the macro.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The aim is to reduce the amount of indirection it takes to get through
the exception handler macros, particularly where it provides little
code sharing.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Conditionally expand the skip case if it is specified.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Conditionally expand the soft-masking test if a mask is passed in.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than pass in the soft-masking and KVM tests via macro that is
passed to another macro to expand it, switch to usig gas macros and
conditionally expand the soft-masking and KVM tests.
The system reset with its idle test is open coded as it is a one-off.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The sreset handler KVM test theoretically should not depend on P7.
In practice KVM now only supports P7 and up so no real bug fix, but
this change is made now so the quirk is not propagated through
cleanup patches.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Re-name the macros to _REAL and _VIRT suffixes rather than no and
_RELON suffix.
- Move the macro definitions together in the file.
- Move RELOCATABLE ifdef inside the _VIRT macro.
Further consolidation between variants does not buy much here.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Switch to a gas macro that conditionally expands the RI clearing
instruction.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace all instances of this with gas macros that test the hsrr
parameter and use the appropriate register names / labels.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Remove extraneous 2nd check for 0xea0 in SOFTEN_TEST]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The opening comment mark "/**" is reserved for kernel-doc comments, so
it will generate a warning with "make W=1".
arch/powerpc/kernel/eeh_cache.c:37: warning: cannot understand function
prototype: 'struct pci_io_addr_range
Since this is not a kernel-doc for the struct below, but rather an
overview of this source eeh_cache.c, just use the free-form comments
kernel-doc syntax instead.
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The protocol for suspending or migrating an LPAR requires all present
processor threads to enter H_JOIN. So if we have threads offline, we
have to temporarily bring them up. This can race with administrator
actions such as SMT state changes. As of dfd718a2ed ("powerpc/rtas:
Fix a potential race between CPU-Offline & Migration"),
rtas_ibm_suspend_me() accounts for this, but errors out with -EBUSY
for what almost certainly is a transient condition in any reasonable
scenario.
Callers of rtas_ibm_suspend_me() already retry when -EAGAIN is
returned, and it is typical during a migration for that to happen
repeatedly for several minutes polling the H_VASI_STATE hcall result
before proceeding to the next stage.
So return -EAGAIN instead of -EBUSY when this race is
encountered. Additionally: logging this event is still appropriate but
use pr_info instead of pr_err; and remove use of unlikely() while here
as this is not a hot path at all.
Fixes: dfd718a2ed ("powerpc/rtas: Fix a potential race between CPU-Offline & Migration")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch into next, this brings in a number of commits
that fix bugs we don't want to hit in next, in particular the fix for
CVE-2019-12817.
One fix for a regression in my commit adding KUAP (Kernel User Access
Prevention) on Radix, which incorrectly touched the AMR in the early machine
check handler.
Thanks to:
Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----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=I22i
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.2-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"One fix for a regression in my commit adding KUAP (Kernel User Access
Prevention) on Radix, which incorrectly touched the AMR in the early
machine check handler.
Thanks to Nicholas Piggin"
* tag 'powerpc-5.2-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s/exception: Fix machine check early corrupting AMR
The early machine check runs in real mode, so locking is unnecessary.
Worse, the windup does not restore AMR, so this can result in a false
KUAP fault after a recoverable machine check hits inside a user copy
operation.
Fix this similarly to HMI by just avoiding the kuap lock in the
early machine check handler (it will be set by the late handler that
runs in virtual mode if that runs). If the virtual mode handler is
reached, it will lock and restore the AMR.
Fixes: 890274c2dc ("powerpc/64s: Implement KUAP for Radix MMU")
Cc: Russell Currey <ruscur@russell.cc>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The return value is fixed. Remove it and amend the callers.
[ tglx: Fixup arm/bL_switcher and powerpc/rtas ]
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.kernel.org/r/20190613064813.8102-2-namit@vmware.com
Seven fixes, all for bugs introduced this cycle.
The commit to add KASAN support broke booting on 32-bit SMP machines, due to a
refactoring that moved some setup out of the secondary CPU path.
A fix for another 32-bit SMP bug introduced by the fast syscall entry
implementation for 32-bit BOOKE. And a build fix for the same commit.
Our change to allow the DAWR to be force enabled on Power9 introduced a bug in
KVM, where we clobber r3 leading to a host crash.
The same commit also exposed a previously unreachable bug in the nested KVM
handling of DAWR, which could lead to an oops in a nested host.
One of the DMA reworks broke the b43legacy WiFi driver on some people's
powermacs, fix it by enabling a 30-bit ZONE_DMA on 32-bit.
A fix for TLB flushing in KVM introduced a new bug, as it neglected to also
flush the ERAT, this could lead to memory corruption in the guest.
Thanks to:
Aaro Koskinen, Christoph Hellwig, Christophe Leroy, Larry Finger, Michael
Neuling, Suraj Jitindar Singh.
-----BEGIN PGP SIGNATURE-----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=Ju1y
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.2-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"This is a frustratingly large batch at rc5. Some of these were sent
earlier but were missed by me due to being distracted by other things,
and some took a while to track down due to needing manual bisection on
old hardware. But still we clearly need to improve our testing of KVM,
and of 32-bit, so that we catch these earlier.
Summary: seven fixes, all for bugs introduced this cycle.
- The commit to add KASAN support broke booting on 32-bit SMP
machines, due to a refactoring that moved some setup out of the
secondary CPU path.
- A fix for another 32-bit SMP bug introduced by the fast syscall
entry implementation for 32-bit BOOKE. And a build fix for the same
commit.
- Our change to allow the DAWR to be force enabled on Power9
introduced a bug in KVM, where we clobber r3 leading to a host
crash.
- The same commit also exposed a previously unreachable bug in the
nested KVM handling of DAWR, which could lead to an oops in a
nested host.
- One of the DMA reworks broke the b43legacy WiFi driver on some
people's powermacs, fix it by enabling a 30-bit ZONE_DMA on 32-bit.
- A fix for TLB flushing in KVM introduced a new bug, as it neglected
to also flush the ERAT, this could lead to memory corruption in the
guest.
Thanks to: Aaro Koskinen, Christoph Hellwig, Christophe Leroy, Larry
Finger, Michael Neuling, Suraj Jitindar Singh"
* tag 'powerpc-5.2-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries
powerpc: enable a 30-bit ZONE_DMA for 32-bit pmac
KVM: PPC: Book3S HV: Only write DAWR[X] when handling h_set_dawr in real mode
KVM: PPC: Book3S HV: Fix r3 corruption in h_set_dabr()
powerpc/32: fix build failure on book3e with KVM
powerpc/booke: fix fast syscall entry on SMP
powerpc/32s: fix initial setup of segment registers on secondary CPU
When the firmware does PCI BAR resource allocation, it passes the assigned
addresses and flags (prefetch/64bit/...) via the "reg" property of
a PCI device device tree node so the kernel does not need to do
resource allocation.
The flags are stored in resource::flags - the lower byte stores
PCI_BASE_ADDRESS_SPACE/etc bits and the other bytes are IORESOURCE_IO/etc.
Some flags from PCI_BASE_ADDRESS_xxx and IORESOURCE_xxx are duplicated,
such as PCI_BASE_ADDRESS_MEM_PREFETCH/PCI_BASE_ADDRESS_MEM_TYPE_64/etc.
When parsing the "reg" property, we copy the prefetch flag but we skip
on PCI_BASE_ADDRESS_MEM_TYPE_64 which leaves the flags out of sync.
The missing IORESOURCE_MEM_64 flag comes into play under 2 conditions:
1. we remove PCI_PROBE_ONLY for pseries (by hacking pSeries_setup_arch()
or by passing "/chosen/linux,pci-probe-only");
2. we request resource alignment (by passing pci=resource_alignment=
via the kernel cmd line to request PAGE_SIZE alignment or defining
ppc_md.pcibios_default_alignment which returns anything but 0). Note that
the alignment requests are ignored if PCI_PROBE_ONLY is enabled.
With 1) and 2), the generic PCI code in the kernel unconditionally
decides to:
- reassign the BARs in pci_specified_resource_alignment() (works fine)
- write new BARs to the device - this fails for 64bit BARs as the generic
code looks at IORESOURCE_MEM_64 (not set) and writes only lower 32bits
of the BAR and leaves the upper 32bit unmodified which breaks BAR mapping
in the hypervisor.
This fixes the issue by copying the flag. This is useful if we want to
enforce certain BAR alignment per platform as handling subpage sized BARs
is proven to cause problems with hotplug (SLOF already aligns BARs to 64k).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Shawn Anastasio <shawn@anastas.io>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Based on 1 normalized pattern(s):
gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 58 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.556988620@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this source code is licensed under the gnu general public license
version 2 see the file copying for more details
this source code is licensed under general public license version 2
see
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 52 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.449021192@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
powerpc hardware triggers watchpoint before executing the instruction.
To make trigger-after-execute behavior, kernel emulates the
instruction. If the instruction is 'load something into non-volatile
register', exception handler should restore emulated register state
while returning back, otherwise there will be register state
corruption. eg, adding a watchpoint on a list can corrput the list:
# cat /proc/kallsyms | grep kthread_create_list
c00000000121c8b8 d kthread_create_list
Add watchpoint on kthread_create_list->prev:
# perf record -e mem:0xc00000000121c8c0
Run some workload such that new kthread gets invoked. eg, I just
logged out from console:
list_add corruption. next->prev should be prev (c000000001214e00), \
but was c00000000121c8b8. (next=c00000000121c8b8).
WARNING: CPU: 59 PID: 309 at lib/list_debug.c:25 __list_add_valid+0xb4/0xc0
CPU: 59 PID: 309 Comm: kworker/59:0 Kdump: loaded Not tainted 5.1.0-rc7+ #69
...
NIP __list_add_valid+0xb4/0xc0
LR __list_add_valid+0xb0/0xc0
Call Trace:
__list_add_valid+0xb0/0xc0 (unreliable)
__kthread_create_on_node+0xe0/0x260
kthread_create_on_node+0x34/0x50
create_worker+0xe8/0x260
worker_thread+0x444/0x560
kthread+0x160/0x1a0
ret_from_kernel_thread+0x5c/0x70
List corruption happened because it uses 'load into non-volatile
register' instruction:
Snippet from __kthread_create_on_node:
c000000000136be8: addis r29,r2,-19
c000000000136bec: ld r29,31424(r29)
if (!__list_add_valid(new, prev, next))
c000000000136bf0: mr r3,r30
c000000000136bf4: mr r5,r28
c000000000136bf8: mr r4,r29
c000000000136bfc: bl c00000000059a2f8 <__list_add_valid+0x8>
Register state from WARN_ON():
GPR00: c00000000059a3a0 c000007ff23afb50 c000000001344e00 0000000000000075
GPR04: 0000000000000000 0000000000000000 0000001852af8bc1 0000000000000000
GPR08: 0000000000000001 0000000000000007 0000000000000006 00000000000004aa
GPR12: 0000000000000000 c000007ffffeb080 c000000000137038 c000005ff62aaa00
GPR16: 0000000000000000 0000000000000000 c000007fffbe7600 c000007fffbe7370
GPR20: c000007fffbe7320 c000007fffbe7300 c000000001373a00 0000000000000000
GPR24: fffffffffffffef7 c00000000012e320 c000007ff23afcb0 c000000000cb8628
GPR28: c00000000121c8b8 c000000001214e00 c000007fef5b17e8 c000007fef5b17c0
Watchpoint hit at 0xc000000000136bec.
addis r29,r2,-19
=> r29 = 0xc000000001344e00 + (-19 << 16)
=> r29 = 0xc000000001214e00
ld r29,31424(r29)
=> r29 = *(0xc000000001214e00 + 31424)
=> r29 = *(0xc00000000121c8c0)
0xc00000000121c8c0 is where we placed a watchpoint and thus this
instruction was emulated by emulate_step. But because handle_dabr_fault
did not restore emulated register state, r29 still contains stale
value in above register state.
Fixes: 5aae8a5370 ("powerpc, hw_breakpoints: Implement hw_breakpoints for 64-bit server processors")
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: stable@vger.kernel.org # 2.6.36+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously, only IBAT1 and IBAT2 were used to map kernel linear mem.
Since commit 63b2bc6195 ("powerpc/mm/32s: Use BATs for
STRICT_KERNEL_RWX"), we may have all 8 BATs used for mapping
kernel text. But the suspend/restore functions only save/restore
BATs 0 to 3, and clears BATs 4 to 7.
Make suspend and restore functions respectively save and reload
the 8 BATs on CPUs having MMU_FTR_USE_HIGH_BATS feature.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
One fix for a regression introduced by our 32-bit KASAN support, which broke
booting on machines with "bootx" early debugging enabled.
A fix for a bug which broke kexec on 32-bit, introduced by changes to the 32-bit
STRICT_KERNEL_RWX support in v5.1.
Finally two fixes going to stable for our THP split/collapse handling,
discovered by Nick. The first fixes random crashes and/or corruption in guests
under sufficient load.
Thanks to:
Nicholas Piggin, Christophe Leroy, Aaro Koskinen, Mathieu Malaterre.
-----BEGIN PGP SIGNATURE-----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=MXJI
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a regression introduced by our 32-bit KASAN support, which
broke booting on machines with "bootx" early debugging enabled.
A fix for a bug which broke kexec on 32-bit, introduced by changes to
the 32-bit STRICT_KERNEL_RWX support in v5.1.
Finally two fixes going to stable for our THP split/collapse handling,
discovered by Nick. The first fixes random crashes and/or corruption
in guests under sufficient load.
Thanks to: Nicholas Piggin, Christophe Leroy, Aaro Koskinen, Mathieu
Malaterre"
* tag 'powerpc-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/32s: fix booting with CONFIG_PPC_EARLY_DEBUG_BOOTX
powerpc/64s: __find_linux_pte() synchronization vs pmdp_invalidate()
powerpc/64s: Fix THP PMD collapse serialisation
powerpc: Fix kexec failure on book3s/32
Build failure was introduced by the commit identified below,
due to missed macro expension leading to wrong called function's name.
arch/powerpc/kernel/head_fsl_booke.o: In function `SystemCall':
arch/powerpc/kernel/head_fsl_booke.S:416: undefined reference to `kvmppc_handler_BOOKE_INTERRUPT_SYSCALL_SPRN_SRR1'
Makefile:1052: recipe for target 'vmlinux' failed
The called function should be kvmppc_handler_8_0x01B(). This patch fixes it.
Reported-by: Paul Mackerras <paulus@ozlabs.org>
Fixes: 1a4b739bbb ("powerpc/32: implement fast entry for syscalls on BOOKE")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Otherwise, the following warning is encountered:
WARNING: vmlinux.o(.text+0x3dc6): Section mismatch in reference from the variable start_here_multiplatform to the function .init.text:.early_setup()
The function start_here_multiplatform() references
the function __init .early_setup().
This is often because start_here_multiplatform lacks a __init
annotation or the annotation of .early_setup is wrong.
Fixes: 56c46bba9b ("powerpc/64: Fix booting large kernels with STRICT_KERNEL_RWX")
Cc: Russell Currey <ruscur@russell.cc>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use r10 instead of r9 to calculate CPU offset as r9 contains
the value from SRR1 which is used later.
Fixes: 1a4b739bbb ("powerpc/32: implement fast entry for syscalls on BOOKE")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch referenced below moved the loading of segment registers
out of load_up_mmu() in order to do it earlier in the boot sequence.
However, the secondary CPU still needs it to be done when loading up
the MMU.
Reported-by: Erhard F. <erhard_f@mailbox.org>
Fixes: 215b823707 ("powerpc/32s: set up an early static hash table for KASAN")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Allow external callers to force the cacheinfo code to release all its
references to cache nodes, e.g. before processing device tree updates
post-migration, and to rebuild the hierarchy afterward.
CPU online/offline must be blocked by callers; enforce this.
Fixes: 410bccf978 ("powerpc/pseries: Partition migration in the kernel")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The declaration for pfn_is_nosave is only available in
kernel/power/power.h. Since this function can be override in arch,
expose it globally. Having a prototype will make sure to avoid warning
(sometime treated as error with W=1) such as:
arch/powerpc/kernel/suspend.c:18:5: error: no previous prototype for 'pfn_is_nosave' [-Werror=missing-prototypes]
This moves the declaration into a globally visible header file and add
missing include to avoid a warning on powerpc.
Also remove the duplicated prototypes since not required anymore.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When booting through OF, setup_disp_bat() does nothing because
disp_BAT are not set. By change, it used to work because BOOTX
buffer is mapped 1:1 at address 0x81000000 by the bootloader, and
btext_setup_display() sets virt addr same as phys addr.
But since commit 215b823707 ("powerpc/32s: set up an early static
hash table for KASAN."), a temporary page table overrides the
bootloader mapping.
This 0x81000000 is also problematic with the newly implemented
Kernel Userspace Access Protection (KUAP) because it is within user
address space.
This patch fixes those issues by properly setting disp_BAT through
a call to btext_prepare_BAT(), allowing setup_disp_bat() to
properly setup BAT3 for early bootx screen buffer access.
Reported-by: Mathieu Malaterre <malat@debian.org>
Fixes: 215b823707 ("powerpc/32s: set up an early static hash table for KASAN.")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the old days, _PAGE_EXEC didn't exist on 6xx aka book3s/32.
Therefore, allthough __mapin_ram_chunk() was already mapping kernel
text with PAGE_KERNEL_TEXT and the rest with PAGE_KERNEL, the entire
memory was executable. Part of the memory (first 512kbytes) was
mapped with BATs instead of page table, but it was also entirely
mapped as executable.
In commit 385e89d5b2 ("powerpc/mm: add exec protection on
powerpc 603"), we started adding exec protection to some 6xx, namely
the 603, for pages mapped via pagetables.
Then, in commit 63b2bc6195 ("powerpc/mm/32s: Use BATs for
STRICT_KERNEL_RWX"), the exec protection was extended to BAT mapped
memory, so that really only the kernel text could be executed.
The problem here is that kexec is based on copying some code into
upper part of memory then executing it from there in order to install
a fresh new kernel at its definitive location.
However, the code is position independant and first part of it is
just there to deactivate the MMU and jump to the second part. So it
is possible to run this first part inplace instead of running the
copy. Once the MMU is off, there is no protection anymore and the
second part of the code will just run as before.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 63b2bc6195 ("powerpc/mm/32s: Use BATs for STRICT_KERNEL_RWX")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
While the TIF_SYSCALL_EMU is set in ptrace_resume independent of any
architecture, currently only powerpc and x86 unset the TIF_SYSCALL_EMU
flag in ptrace_disable which gets called from ptrace_detach.
Let's move the clearing of TIF_SYSCALL_EMU flag to __ptrace_unlink
which gets executed from ptrace_detach and also keep it along with
or close to clearing of TIF_SYSCALL_TRACE.
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Based on 1 normalized pattern(s):
distribute under gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.475576622@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation 51 franklin street fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 67 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141333.953658117@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A minor fix to our IMC PMU code to print a less confusing error message when the
driver can't initialise properly.
A fix for a bug where a user requesting an unsupported branch sampling filter
can corrupt PMU state, preventing the PMU from counting properly.
And finally a fix for a bug in our support for kexec_file_load(), which
prevented loading a kernel and initramfs. Most versions of kexec don't yet use
kexec_file_load().
Thanks to:
Anju T Sudhakar, Dave Young, Madhavan Srinivasan, Ravi Bangoria, Thiago Jung
Bauermann.
-----BEGIN PGP SIGNATURE-----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=ilhV
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A minor fix to our IMC PMU code to print a less confusing error
message when the driver can't initialise properly.
A fix for a bug where a user requesting an unsupported branch sampling
filter can corrupt PMU state, preventing the PMU from counting
properly.
And finally a fix for a bug in our support for kexec_file_load(),
which prevented loading a kernel and initramfs. Most versions of kexec
don't yet use kexec_file_load().
Thanks to: Anju T Sudhakar, Dave Young, Madhavan Srinivasan, Ravi
Bangoria, Thiago Jung Bauermann"
* tag 'powerpc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kexec: Fix loading of kernel + initramfs with kexec_file_load()
powerpc/perf: Fix MMCRA corruption by bhrb_filter
powerpc/powernv: Return for invalid IMC domain
On POWER9, if the hypervisor supports XIVE exploitation mode, the
guest OS will unconditionally requests for the XIVE interrupt mode
even if XIVE was deactivated with the kernel command line xive=off.
Later on, when the spapr XIVE init code handles xive=off, it disables
XIVE and tries to fall back on the legacy mode XICS.
This discrepency causes a kernel panic because the hypervisor is
configured to provide the XIVE interrupt mode to the guest :
kernel BUG at arch/powerpc/sysdev/xics/xics-common.c:135!
...
NIP xics_smp_probe+0x38/0x98
LR xics_smp_probe+0x2c/0x98
Call Trace:
xics_smp_probe+0x2c/0x98 (unreliable)
pSeries_smp_probe+0x40/0xa0
smp_prepare_cpus+0x62c/0x6ec
kernel_init_freeable+0x148/0x448
kernel_init+0x2c/0x148
ret_from_kernel_thread+0x5c/0x68
Look for xive=off during prom_init and don't ask for XIVE in this
case. One exception though: if the host only supports XIVE, we still
want to boot so we ignore xive=off.
Similarly, have the spapr XIVE init code to looking at the interrupt
mode negotiated during CAS, and ignore xive=off if the hypervisor only
supports XIVE.
Fixes: eac1e731b5 ("powerpc/xive: guest exploitation of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.20
Reported-by: Pavithra R. Prakash <pavrampu@in.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit eab00a208e ("powerpc: Move `path` variable inside
DEBUG_PROM") DEBUG_PROM sentinels were added to silence a warning
(treated as error with W=1):
arch/powerpc/kernel/prom_init.c:1388:8: error: variable ‘path’ set but not used [-Werror=unused-but-set-variable]
Rework the original patch and simplify the code, by removing the
variable ‘path’ completely. Fix line over 90 characters.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Based on 1 normalized pattern(s):
licensed under gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 99 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.163048684@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As synchronous exceptions really only make sense against the current
task (otherwise how are you synchronous) remove the task parameter
from from force_sig_fault to make it explicit that is what is going
on.
The two known exceptions that deliver a synchronous exception to a
stopped ptraced task have already been changed to
force_sig_fault_to_task.
The callers have been changed with the following emacs regular expression
(with obvious variations on the architectures that take more arguments)
to avoid typos:
force_sig_fault[(]\([^,]+\)[,]\([^,]+\)[,]\([^,]+\)[,]\W+current[)]
->
force_sig_fault(\1,\2,\3)
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
All of the remaining callers pass current into force_sig so
remove the task parameter to make this obvious and to make
misuse more difficult in the future.
This also makes it clear force_sig passes current into force_sig_info.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b6664ba42f ("s390, kexec_file: drop arch_kexec_mem_walk()")
changed kexec_add_buffer() to skip searching for a memory location if
kexec_buf.mem is already set, and use the address that is there.
In powerpc code we reuse a kexec_buf variable for loading both the
kernel and the initramfs by resetting some of the fields between those
uses, but not mem. This causes kexec_add_buffer() to try to load the
kernel at the same address where initramfs will be loaded, which is
naturally rejected:
# kexec -s -l --initrd initramfs vmlinuz
kexec_file_load failed: Invalid argument
Setting the mem field before every call to kexec_add_buffer() fixes
this regression.
Fixes: b6664ba42f ("s390, kexec_file: drop arch_kexec_mem_walk()")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Reviewed-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge yet more updates from Andrew Morton:
"A few final bits:
- large changes to vmalloc, yielding large performance benefits
- tweak the console-flush-on-panic code
- a few fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
panic: add an option to replay all the printk message in buffer
initramfs: don't free a non-existent initrd
fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going into workqueue when umount
mm/compaction.c: correct zone boundary handling when isolating pages from a pageblock
mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macro
mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macro
mm/vmalloc.c: keep track of free blocks for vmap allocation
One fix going back to stable, for a bug on 32-bit introduced when we added
support for THREAD_INFO_IN_TASK.
A fix for a typo in a recent rework of our hugetlb code that leads to crashes on
64-bit when using hugetlbfs with a 4K PAGE_SIZE.
Two fixes for our recent rework of the address layout on 64-bit hash CPUs, both
only triggered when userspace tries to access addresses outside the user or
kernel address ranges.
Finally a fix for a recently introduced double free in an error path in our
cacheinfo code.
Thanks to:
Aneesh Kumar K.V, Christophe Leroy, Sachin Sant, Tobin C. Harding.
-----BEGIN PGP SIGNATURE-----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=2265
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix going back to stable, for a bug on 32-bit introduced when we
added support for THREAD_INFO_IN_TASK.
A fix for a typo in a recent rework of our hugetlb code that leads to
crashes on 64-bit when using hugetlbfs with a 4K PAGE_SIZE.
Two fixes for our recent rework of the address layout on 64-bit hash
CPUs, both only triggered when userspace tries to access addresses
outside the user or kernel address ranges.
Finally a fix for a recently introduced double free in an error path
in our cacheinfo code.
Thanks to: Aneesh Kumar K.V, Christophe Leroy, Sachin Sant, Tobin C.
Harding"
* tag 'powerpc-5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/cacheinfo: Remove double free
powerpc/mm/hash: Fix get_region_id() for invalid addresses
powerpc/mm: Drop VM_BUG_ON in get_region_id()
powerpc/mm: Fix crashes with hugepages & 4K pages
powerpc/32s: fix flush_hash_pages() on SMP
Currently on panic, kernel will lower the loglevel and print out pending
printk msg only with console_flush_on_panic().
Add an option for users to configure the "panic_print" to replay all
dmesg in buffer, some of which they may have never seen due to the
loglevel setting, which will help panic debugging .
[feng.tang@intel.com: keep the original console_flush_on_panic() inside panic()]
Link: http://lkml.kernel.org/r/1556199137-14163-1-git-send-email-feng.tang@intel.com
[feng.tang@intel.com: use logbuf lock to protect the console log index]
Link: http://lkml.kernel.org/r/1556269868-22654-1-git-send-email-feng.tang@intel.com
Link: http://lkml.kernel.org/r/1556095872-36838-1-git-send-email-feng.tang@intel.com
Signed-off-by: Feng Tang <feng.tang@intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more vfs mount updates from Al Viro:
"Propagation of new syscalls to other architectures + cosmetic change
from Christian (fscontext didn't follow the convention for anon inode
names)"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
uapi: Wire up the mount API syscalls on non-x86 arches [ver #2]
uapi, x86: Fix the syscall numbering of the mount API syscalls [ver #2]
uapi, fsopen: use square brackets around "fscontext" [ver #2]
kfree() after kobject_put(). Who ever wrote this was on crack.
Fixes: 7e8039795a ("powerpc/cacheinfo: Fix kobject memleak")
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Wire up the mount API syscalls on non-x86 arches.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
CONFIG_DEBUG_KERNEL should not impact code generation. Use the newly
defined CONFIG_DEBUG_MISC instead to keep the current code.
Link: http://lkml.kernel.org/r/20190413224438.10802-3-okaya@kernel.org
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Florian Westphal <fw@strlen.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This prepares to move CONFIG_OPTIMIZE_INLINING from x86 to a common
place. We need to eliminate potential issues beforehand.
If it is enabled for powerpc, the following modpost warnings are
reported:
WARNING: vmlinux.o(.text.unlikely+0x20): Section mismatch in reference from the function .prom_getprop() to the function .init.text:.call_prom()
The function .prom_getprop() references the function __init .call_prom().
This is often because .prom_getprop lacks a __init annotation or the annotation of .call_prom is wrong.
WARNING: vmlinux.o(.text.unlikely+0x3c): Section mismatch in reference from the function .prom_getproplen() to the function .init.text:.call_prom()
The function .prom_getproplen() references the function __init .call_prom().
This is often because .prom_getproplen lacks a __init annotation or the annotation of .call_prom is wrong.
Link: http://lkml.kernel.org/r/20190423034959.13525-9-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights:
- Support for Kernel Userspace Access/Execution Prevention (like
SMAP/SMEP/PAN/PXN) on some 64-bit and 32-bit CPUs. This prevents the kernel
from accidentally accessing userspace outside copy_to/from_user(), or
ever executing userspace.
- KASAN support on 32-bit.
- Rework of where we map the kernel, vmalloc, etc. on 64-bit hash to use the
same address ranges we use with the Radix MMU.
- A rewrite into C of large parts of our idle handling code for 64-bit Book3S
(ie. power8 & power9).
- A fast path entry for syscalls on 32-bit CPUs, for a 12-17% speedup in the
null_syscall benchmark.
- On 64-bit bare metal we have support for recovering from errors with the time
base (our clocksource), however if that fails currently we hang in __delay()
and never crash. We now have support for detecting that case and short
circuiting __delay() so we at least panic() and reboot.
- Add support for optionally enabling the DAWR on Power9, which had to be
disabled by default due to a hardware erratum. This has the effect of
enabling hardware breakpoints for GDB, the downside is a badly behaved
program could crash the machine by pointing the DAWR at cache inhibited
memory. This is opt-in obviously.
- xmon, our crash handler, gets support for a read only mode where operations
that could change memory or otherwise disturb the system are disabled.
Plus many clean-ups, reworks and minor fixes etc.
Thanks to:
Christophe Leroy, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anton Blanchard, Ben Hutchings,
Bo YU, Breno Leitao, Cédric Le Goater, Christopher M. Riedl, Christoph
Hellwig, Colin Ian King, David Gibson, Ganesh Goudar, Gautham R. Shenoy,
George Spelvin, Greg Kroah-Hartman, Greg Kurz, Horia Geantă, Jagadeesh
Pagadala, Joel Stanley, Joe Perches, Julia Lawall, Laurentiu Tudor, Laurent
Vivier, Lukas Bulwahn, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu
Malaterre, Michael Neuling, Mukesh Ojha, Nathan Fontenot, Nathan Lynch,
Nicholas Piggin, Nick Desaulniers, Oliver O'Halloran, Peng Hao, Qian Cai, Ravi
Bangoria, Rick Lindsley, Russell Currey, Sachin Sant, Stewart Smith, Sukadev
Bhattiprolu, Thomas Huth, Tobin C. Harding, Tyrel Datwyler, Valentin
Schneider, Wei Yongjun, Wen Yang, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=cUkd
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.2-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Slightly delayed due to the issue with printk() calling
probe_kernel_read() interacting with our new user access prevention
stuff, but all fixed now.
The only out-of-area changes are the addition of a cpuhp_state, small
additions to Documentation and MAINTAINERS updates.
Highlights:
- Support for Kernel Userspace Access/Execution Prevention (like
SMAP/SMEP/PAN/PXN) on some 64-bit and 32-bit CPUs. This prevents
the kernel from accidentally accessing userspace outside
copy_to/from_user(), or ever executing userspace.
- KASAN support on 32-bit.
- Rework of where we map the kernel, vmalloc, etc. on 64-bit hash to
use the same address ranges we use with the Radix MMU.
- A rewrite into C of large parts of our idle handling code for
64-bit Book3S (ie. power8 & power9).
- A fast path entry for syscalls on 32-bit CPUs, for a 12-17% speedup
in the null_syscall benchmark.
- On 64-bit bare metal we have support for recovering from errors
with the time base (our clocksource), however if that fails
currently we hang in __delay() and never crash. We now have support
for detecting that case and short circuiting __delay() so we at
least panic() and reboot.
- Add support for optionally enabling the DAWR on Power9, which had
to be disabled by default due to a hardware erratum. This has the
effect of enabling hardware breakpoints for GDB, the downside is a
badly behaved program could crash the machine by pointing the DAWR
at cache inhibited memory. This is opt-in obviously.
- xmon, our crash handler, gets support for a read only mode where
operations that could change memory or otherwise disturb the system
are disabled.
Plus many clean-ups, reworks and minor fixes etc.
Thanks to: Christophe Leroy, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
Anton Blanchard, Ben Hutchings, Bo YU, Breno Leitao, Cédric Le Goater,
Christopher M. Riedl, Christoph Hellwig, Colin Ian King, David Gibson,
Ganesh Goudar, Gautham R. Shenoy, George Spelvin, Greg Kroah-Hartman,
Greg Kurz, Horia Geantă, Jagadeesh Pagadala, Joel Stanley, Joe
Perches, Julia Lawall, Laurentiu Tudor, Laurent Vivier, Lukas Bulwahn,
Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
Neuling, Mukesh Ojha, Nathan Fontenot, Nathan Lynch, Nicholas Piggin,
Nick Desaulniers, Oliver O'Halloran, Peng Hao, Qian Cai, Ravi
Bangoria, Rick Lindsley, Russell Currey, Sachin Sant, Stewart Smith,
Sukadev Bhattiprolu, Thomas Huth, Tobin C. Harding, Tyrel Datwyler,
Valentin Schneider, Wei Yongjun, Wen Yang, YueHaibing"
* tag 'powerpc-5.2-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (205 commits)
powerpc/64s: Use early_mmu_has_feature() in set_kuap()
powerpc/book3s/64: check for NULL pointer in pgd_alloc()
powerpc/mm: Fix hugetlb page initialization
ocxl: Fix return value check in afu_ioctl()
powerpc/mm: fix section mismatch for setup_kup()
powerpc/mm: fix redundant inclusion of pgtable-frag.o in Makefile
powerpc/mm: Fix makefile for KASAN
powerpc/kasan: add missing/lost Makefile
selftests/powerpc: Add a signal fuzzer selftest
powerpc/booke64: set RI in default MSR
ocxl: Provide global MMIO accessors for external drivers
ocxl: move event_fd handling to frontend
ocxl: afu_irq only deals with IRQ IDs, not offsets
ocxl: Allow external drivers to use OpenCAPI contexts
ocxl: Create a clear delineation between ocxl backend & frontend
ocxl: Don't pass pci_dev around
ocxl: Split pci.c
ocxl: Remove some unused exported symbols
ocxl: Remove superfluous 'extern' from headers
ocxl: read_pasid never returns an error, so make it void
...
Pull speculation mitigation update from Ingo Molnar:
"This adds the "mitigations=" bootline option, which offers a
cross-arch set of options that will work on x86, PowerPC and s390 that
will map to the arch specific option internally"
* 'core-speculation-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
s390/speculation: Support 'mitigations=' cmdline option
powerpc/speculation: Support 'mitigations=' cmdline option
x86/speculation: Support 'mitigations=' cmdline option
cpu/speculation: Add 'mitigations=' cmdline option
On TOD/TB errors timebase register stops/freezes until HMI error recovery
gets TOD/TB back into running state. On successful recovery, TB starts
running again and udelay() that relies on TB value continues to function
properly. But in case when HMI fails to recover from TOD/TB errors, the
TB register stay freezed. With TB not running the __delay() function
keeps looping and never return. If __delay() is called while in panic
path then system hangs and never reboots after panic.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
[mpe: Rebase since CURRENT_THREAD_INFO() removal]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PROM_SCRATCH_SIZE is same as sizeof(prom_scratch)
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This can be helpful for debugging problems with the security feature
flags, especially on guests where the flags come from the hypervisor
via an hcall and so can't be observed in the device tree.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
"Reconciling" in terms of interrupt handling, is to bring the soft irq
mask state in to synch with the hardware, after an interrupt causes
MSR[EE] to be cleared (while the soft mask may be enabled, and hard
irqs not marked disabled).
General kernel code should not be called while unreconciled, because
local_irq_disable, etc. manipulations can cause surprising irq traces,
and it's fragile because the soft irq code does not really expect to
be called in this situation.
When exiting from an interrupt, MSR[EE] is cleared to prevent races,
but soft irq state is enabled for the returned-to context, so this is
now an unreconciled state. restore_math is called in this state, and
that can be ftraced, and the ftrace subsystem disables local irqs.
Mark restore_math and its callees as notrace. Restore a sanity check
in the soft irq code that had to be disabled for this case, by commit
4da1f79227 ("powerpc/64: Disable irq restore warning for now").
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch drops__irq_offset_value which has not been used since
commit 9c4cb82515 ("powerpc: Remove use of CONFIG_PPC_MERGE")
This removes a sparse warning.
Fixes: 9c4cb82515 ("powerpc: Remove use of CONFIG_PPC_MERGE")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Compared to ifdefs, IS_ENABLED() provide a cleaner code and allows
to detect compilation failure regardless of the selected options.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use cpu_has_feature() instead of opencoding
Use IS_ENABLED() instead of #ifdef for CONFIG_TAU_AVERAGE
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CPU_FTR_ALTIVEC is only set when CONFIG_ALTIVEC is selected, so
the ifdef is unnecessary.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To avoid ifdefs, define a empty static inline mm_iommu_init() function
when CONFIG_SPAPR_TCE_IOMMU is not selected.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To avoid #ifdefs, define an static inline fadump_cleanup() function
when CONFIG_FADUMP is not selected
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No need to add dummy frames when calling trace_hardirqs_on or
trace_hardirqs_off. GCC properly handles empty stacks.
In addition, powerpc doesn't set CONFIG_FRAME_POINTER, therefore
__builtin_return_address(1..) returns NULL at all time. So the
dummy frames are definitely unneeded here.
In the meantime, avoid reading memory for loading r1 with a value
we already know.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As syscalls are now handled via a fast entry path, syscall related
actions can be removed from the generic transfer_to_handler path.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch implements a fast entry for syscalls.
Syscalls don't have to preserve non volatile registers except LR.
This patch then implement a fast entry for syscalls, where
volatile registers get clobbered.
As this entry is dedicated to syscall it always sets MSR_EE
and warns in case MSR_EE was previously off
It also assumes that the call is always from user, system calls are
unexpected from kernel.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch implements a fast entry for syscalls.
Syscalls don't have to preserve non volatile registers except LR.
This patch then implement a fast entry for syscalls, where
volatile registers get clobbered.
As this entry is dedicated to syscall it always sets MSR_EE
and warns in case MSR_EE was previously off
It also assumes that the call is always from user, system calls are
unexpected from kernel.
The overall series improves null_syscall selftest by 12,5% on an 83xx
and by 17% on a 8xx.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[text mostly copied from benh's RFC/WIP]
ppc32 are still doing something rather gothic and wrong on 32-bit
which we stopped doing on 64-bit a while ago.
We have that thing where some handlers "copy" the EE value from the
original stack frame into the new MSR before transferring to the
handler.
Thus for a number of exceptions, we enter the handlers with interrupts
enabled.
This is rather fishy, some of the stuff that handlers might do early
on such as irq_enter/exit or user_exit, context tracking, etc...
should be run with interrupts off afaik.
Generally our handlers know when to re-enable interrupts if needed.
The problem we were having is that we assumed these interrupts would
return with interrupts enabled. However that isn't the case.
Instead, this patch changes things so that we always enter exception
handlers with interrupts *off* with the notable exception of syscalls
which are special (and get a fast path).
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
EXC_XFER_TEMPLATE() is not called with COPY_EE anymore so
we can get rid of copyee parameters and related COPY_EE and NOCOPY
macros.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[splited out from benh RFC patch]
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All exceptions handlers know when to reenable interrupts, so
it is safer to enter all of them with MSR_EE unset, except
for syscalls.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[splited out from benh RFC patch]
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
syscalls are expected to be entered with MSR_EE set. Lets
make it inconditional by forcing MSR_EE on syscalls.
This patch adds EXC_XFER_SYS for that.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[splited out from benh RFC patch]
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
SPEFloatingPointException() is the only exception handler which 'forgets' to
re-enable interrupts. This patch makes sure it does.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Refactor exception entry macros by using the ones defined in head_32.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch splits NORMAL_EXCEPTION_PROLOG in the same way as in
head_8xx.S and head_32.S and renames it EXCEPTION_PROLOG() as well
to match head_32.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Unlike said in the comment, r1 is not reused by the critical
exception handler, as it uses a dedicated critirq_ctx stack.
Decrementing r1 early is then unneeded.
Should the above be valid, the code is crap buggy anyway as
r1 gets some intermediate values that would jeopardise the
whole process (for instance after mfspr r1,SPRN_SPRG_THREAD)
Using SPRN_SPRG_SCRATCH2 to save r1 is then not needed, r11 can be
used instead. This avoids one mtspr and one mfspr and makes the
prolog closer to what's done on 6xx and 8xx.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
6xx/8xx EXC_XFER_TEMPLATE() macro adds a i##n symbol which is
unused and can be removed.
40x and booke EXC_XFER_TEMPLATE() macros takes msr from the caller
while the 6xx/8xx version uses only MSR_KERNEL as msr value.
This patch modifies the 6xx/8xx version to make it similar to the
40x and booke versions.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As preparation for using head_32.h for head_40x.S, move
LOAD_MSR_KERNEL() there and use it to load r10 with MSR_KERNEL value.
In the mean time, this patch modifies it so that it takes into account
the size of the passed value to determine if 'li' can be used or if
'lis/ori' is needed instead of using the size of MSR_KERNEL. This is
done by using gas macro.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
EXCEPTION_PROLOG is similar in head_8xx.S and head_32.S
This patch creates head_32.h and moves EXCEPTION_PROLOG macro
into it. It also converts it from a GCC macro to a GAS macro
in order to ease refactorisation with 40x later, since
GAS macros allows the use of #ifdef/#else/#endif inside it.
And it also has the advantage of not requiring the uggly "; \"
at the end of each line.
This patch also moves EXCEPTION() and EXC_XFER_XXXX() macros which
are also similar while adding START_EXCEPTION() out of EXCEPTION().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reduce #ifdef mess by defining a helper to print
hash info at startup.
In the meantime, remove the display of hash table address
to reduce leak of non necessary information.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
KASAN requires early activation of hash table, before memblock()
functions are available.
This patch implements an early hash_table statically defined in
__initdata.
During early boot, a single page table is used.
For hash32, when doing the final init, one page table is allocated
for each PGD entry because of the _PAGE_HASHPTE flag which can't be
common to several virt pages. This is done after memblock get
available but before switching to the final hash table, otherwise
there are issues with TLB flushing due to the shared entries.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For KASAN, hash table handling will be activated early for
accessing to KASAN shadow areas.
In order to avoid any modification of the hash functions while
they are still used with the early hash table, the code patching
is moved out of MMU_init_hw() and put close to the big-bang switch
to the final hash table.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds KASAN support for PPC32. The following patch
will add an early activation of hash table for book3s. Until
then, a warning will be raised if trying to use KASAN on an
hash 6xx.
To support KASAN, this patch initialises that MMU mapings for
accessing to the KASAN shadow area defined in a previous patch.
An early mapping is set as soon as the kernel code has been
relocated at its definitive place.
Then the definitive mapping is set once paging is initialised.
For modules, the shadow area is allocated at module_alloc().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All files containing functions run before kasan_early_init() is called
must have KASAN instrumentation disabled.
For those file, branch profiling also have to be disabled otherwise
each if () generates a call to ftrace_likely_update().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 400c47d81c ("powerpc32: memset: only use dcbz once cache is
enabled"), memset() can be used before activation of the cache,
so no need to use memset_io() for zeroing the BSS.
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In kernel/cputable.c, explicitly use memcpy() instead of *y = *x;
This will allow GCC to replace it with __memcpy() when KASAN is
selected.
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When KASAN is active, the string functions in lib/ are doing the
KASAN checks. This is too early for prom_init.
This patch implements dedicated string functions for prom_init,
which will be compiled in with KASAN disabled.
Size of prom_init before the patch:
text data bss dec hex filename
12060 488 6960 19508 4c34 arch/powerpc/kernel/prom_init.o
Size of prom_init after the patch:
text data bss dec hex filename
12460 488 6960 19908 4dc4 arch/powerpc/kernel/prom_init.o
This increases the size of prom_init a bit, but as prom_init is
in __init section, it is freed after boot anyway.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch makes CONFIG_CMDLINE defined at all time. It avoids
having to enclose related code inside #ifdef CONFIG_CMDLINE
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_KASAN implements wrappers for memcpy() memmove() and memset()
Those wrappers are doing the verification then call respectively
__memcpy() __memmove() and __memset(). The arches are therefore
expected to rename their optimised functions that way.
For files on which KASAN is inhibited, #defines are used to allow
them to directly call optimised versions of the functions without
going through the KASAN wrappers.
See commit 393f203f5f ("x86_64: kasan: add interceptors for
memset/memmove/memcpy functions") for details.
Other string / mem functions do not (yet) have kasan wrappers,
we therefore have to fallback to the generic versions when
KASAN is active, otherwise KASAN checks will be skipped.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Fixups to keep selftests working]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In preparation of KASAN, move early_init() into a separate
file in order to allow deactivation of KASAN for that function.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No need to have this in asm/page.h, move it into asm/hugetlb.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 67fda38f0d ("powerpc/mm: Move slb_addr_linit to
early_init_mmu") moved slb_addr_limit init out of setup_arch().
Commit 701101865f ("powerpc/mm: Reduce memory usage for mm_context_t
for radix") brought it back into setup_arch() by error.
This patch reverts that erroneous regress.
Fixes: 701101865f ("powerpc/mm: Reduce memory usage for mm_context_t for radix")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a kernel crash that happens if rt_sigreturn() is called inside
a transactional block.
This crash happens if the kernel hits an in-kernel page fault when
accessing userspace memory, usually through copy_ckvsx_to_user(). A
major page fault calls might_sleep() function, which can cause a task
reschedule. A task reschedule (switch_to()) reclaim and recheckpoint
the TM states, but, in the signal return path, the checkpointed memory
was already reclaimed, thus the exception stack has MSR that points to
MSR[TS]=0.
When the code returns from might_sleep() and a task reschedule
happened, then this task is returned with the memory recheckpointed,
and CPU MSR[TS] = suspended.
This means that there is a side effect at might_sleep() if it is
called with CPU MSR[TS] = 0 and the task has regs->msr[TS] != 0.
This side effect can cause a TM bad thing, since at the exception
entrance, the stack saves MSR[TS]=0, and this is what will be used at
RFID, but, the processor has MSR[TS] = Suspended, and this transition
will be invalid and a TM Bad thing will be raised, causing the
following crash:
Unexpected TM Bad Thing exception at c00000000000e9ec (msr 0x8000000302a03031) tm_scratch=800000010280b033
cpu 0xc: Vector: 700 (Program Check) at [c00000003ff1fd70]
pc: c00000000000e9ec: fast_exception_return+0x100/0x1bc
lr: c000000000032948: handle_rt_signal64+0xb8/0xaf0
sp: c0000004263ebc40
msr: 8000000302a03031
current = 0xc000000415050300
paca = 0xc00000003ffc4080 irqmask: 0x03 irq_happened: 0x01
pid = 25006, comm = sigfuz
Linux version 5.0.0-rc1-00001-g3bd6e94bec12 (breno@debian) (gcc version 8.2.0 (Debian 8.2.0-3)) #899 SMP Mon Jan 7 11:30:07 EST 2019
WARNING: exception is not recoverable, can't continue
enter ? for help
[c0000004263ebc40] c000000000032948 handle_rt_signal64+0xb8/0xaf0 (unreliable)
[c0000004263ebd30] c000000000022780 do_notify_resume+0x2f0/0x430
[c0000004263ebe20] c00000000000e844 ret_from_except_lite+0x70/0x74
--- Exception: c00 (System Call) at 00007fffbaac400c
SP (7fffeca90f40) is in userspace
The solution for this problem is running the sigreturn code with
regs->msr[TS] disabled, thus, avoiding hitting the side effect above.
This does not seem to be a problem since regs->msr will be replaced by
the ucontext value, so, it is being flushed already. In this case, it
is flushed earlier.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Print more information about MCE error whether it is an hardware or
software error.
Some of the MCE errors can be easily categorized as hardware or
software errors e.g. UEs are due to hardware error, where as error
triggered due to invalid usage of tlbie is a pure software bug. But
not all the MCE errors can be easily categorize into either software
or hardware. There are errors like multihit errors which are usually
result of a software bug, but in some rare cases a hardware failure
can cause a multihit error. In past, we have seen case where after
replacing faulty chip, multihit errors stopped occurring. Same with
parity errors, which are usually due to faulty hardware but there are
chances where multihit can also cause an parity error. Such errors are
difficult to determine what really caused it. Hence this patch
classifies MCE errors into following four categorize:
1. Hardware error:
UE and Link timeout failure errors.
2. Probable hardware error (some chance of software cause)
SLB/ERAT/TLB Parity errors.
3. Software error
Invalid tlbie form.
4. Probable software error (some chance of hardware cause)
SLB/ERAT/TLB Multihit errors.
Sample output:
MCE: CPU80: machine check (Warning) Guest SLB Multihit DAR: 000001001b6e0320 [Recovered]
MCE: CPU80: PID: 24765 Comm: qemu-system-ppc Guest NIP: [00007fffa309dc60]
MCE: CPU80: Probable Software error (some chance of hardware cause)
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently all machine check errors are printed as severe errors which
isn't correct. Print soft errors as warning instead of severe errors.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When analysing sources of OS jitter, I noticed that doorbells cannot be
traced.
Signed-off-by: Anton Blanchard <anton@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 2bf1071a8d ("powerpc/64s: Remove POWER9 DD1 support") the
function __switch_to remove usage for 'dummy_copy_buffer'. Since it is
not used anywhere else, remove it completely.
This remove the following warning:
arch/powerpc/kernel/process.c:1156:17: error: 'dummy_copy_buffer' defined but not used
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently error return from kobject_init_and_add() is not followed by
a call to kobject_put(). This means there is a memory leak.
Add call to kobject_put() in error path of kobject_init_and_add().
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Towards the goal of removing cc-ldoption, it seems that --hash-style=
was added to binutils 2.17.50.0.2 in 2006. The minimal required
version of binutils for the kernel according to
Documentation/process/changes.rst is 2.20.
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reimplement Book3S idle code in C, moving POWER7/8/9 implementation
speific HV idle code to the powernv platform code.
Book3S assembly stubs are kept in common code and used only to save
the stack frame and non-volatile GPRs before executing architected
idle instructions, and restoring the stack and reloading GPRs then
returning to C after waking from idle.
The complex logic dealing with threads and subcores, locking, SPRs,
HMIs, timebase resync, etc., is all done in C which makes it more
maintainable.
This is not a strict translation to C code, there are some
significant differences:
- Idle wakeup no longer uses the ->cpu_restore call to reinit SPRs,
but saves and restores them itself.
- The optimisation where EC=ESL=0 idle modes did not have to save GPRs
or change MSR is restored, because it's now simple to do. ESL=1
sleeps that do not lose GPRs can use this optimization too.
- KVM secondary entry and cede is now more of a call/return style
rather than branchy. nap_state_lost is not required because KVM
always returns via NVGPR restoring path.
- KVM secondary wakeup from offline sequence is moved entirely into
the offline wakeup, which avoids a hwsync in the normal idle wakeup
path.
Performance measured with context switch ping-pong on different
threads or cores, is possibly improved a small amount, 1-3% depending
on stop state and core vs thread test for shallow states. Deep states
it's in the noise compared with other latencies.
KVM improvements:
- Idle sleepers now always return to caller rather than branch out
to KVM first.
- This allows optimisations like very fast return to caller when no
state has been lost.
- KVM no longer requires nap_state_lost because it controls NVGPR
save/restore itself on the way in and out.
- The heavy idle wakeup KVM request check can be moved out of the
normal host idle code and into the not-performance-critical offline
code.
- KVM nap code now returns from where it is called, which makes the
flow a bit easier to follow.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Squash the KVM changes in]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Using a jiffies timer creates a dependency on the tick_do_timer_cpu
incrementing jiffies. If that CPU has locked up and jiffies is not
incrementing, the watchdog heartbeat timer for all CPUs stops and
creates false positives and confusing warnings on local CPUs, and
also causes the SMP detector to stop, so the root cause is never
detected.
Fix this by using hrtimer based timers for the watchdog heartbeat,
like the generic kernel hardlockup detector.
Cc: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reported-by: Ravikumar Bangoria <ravi.bangoria@in.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reported-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This comes a bit late, but should be in 5.1 anyway: we want the newly
added system calls to be synchronized across all architectures in
the release.
I hope that in the future, any newly added system calls can be added
to all architectures at the same time, and tested there while they
are in linux-next, avoiding dependencies between the architecture
maintainer trees and the tree that contains the new system call.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Y7Kd
-----END PGP SIGNATURE-----
Merge tag 'syscalls-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull syscall numbering updates from Arnd Bergmann:
"arch: add pidfd and io_uring syscalls everywhere
This comes a bit late, but should be in 5.1 anyway: we want the newly
added system calls to be synchronized across all architectures in the
release.
I hope that in the future, any newly added system calls can be added
to all architectures at the same time, and tested there while they are
in linux-next, avoiding dependencies between the architecture
maintainer trees and the tree that contains the new system call"
* tag 'syscalls-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: add pidfd and io_uring syscalls everywhere
This helps in debugging. We can look at the dmesg to find out
different kernel mapping details.
On 4K config this shows
kernel vmalloc start = 0xc000100000000000
kernel IO start = 0xc000200000000000
kernel vmemmap start = 0xc000300000000000
On 64K config:
kernel vmalloc start = 0xc008000000000000
kernel IO start = 0xc00a000000000000
kernel vmemmap start = 0xc00c000000000000
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, our mm_context_t on book3s64 include all hash specific
context details like slice mask and subpage protection details. We
can skip allocating these with radix translation. This will help us to save
8K per mm_context with radix translation.
With the patch applied we have
sizeof(mm_context_t) = 136
sizeof(struct hash_mm_context) = 8288
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Avoid #ifdef in generic code. Also enables us to do this specific to
MMU translation mode on book3s64
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We want to switch to allocating them runtime only when hash translation is
enabled. Add helpers so that both book3s and nohash can be adapted to
upcoming change easily.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch implements Kernel Userspace Access Protection for
book3s/32.
Due to limitations of the processor page protection capabilities,
the protection is only against writing. read protection cannot be
achieved using page protection.
The previous patch modifies the page protection so that RW user
pages are RW for Key 0 and RO for Key 1, and it sets Key 0 for
both user and kernel.
This patch changes userspace segment registers are set to Ku 0
and Ks 1. When kernel needs to write to RW pages, the associated
segment register is then changed to Ks 0 in order to allow write
access to the kernel.
In order to avoid having the read all segment registers when
locking/unlocking the access, some data is kept in the thread_struct
and saved on stack on exceptions. The field identifies both the
first unlocked segment and the first segment following the last
unlocked one. When no segment is unlocked, it contains value 0.
As the hash_page() function is not able to easily determine if a
protfault is due to a bad kernel access to userspace, protfaults
need to be handled by handle_page_fault when KUAP is set.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Drop allow_read/write_to/from_user() as they're now in kup.h,
and adapt allow_user_access() to do nothing when to == NULL]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch prepares Kernel Userspace Access Protection for
book3s/32.
Due to limitations of the processor page protection capabilities,
the protection is only against writing. read protection cannot be
achieved using page protection.
book3s/32 provides the following values for PP bits:
PP00 provides RW for Key 0 and NA for Key 1
PP01 provides RW for Key 0 and RO for Key 1
PP10 provides RW for all
PP11 provides RO for all
Today PP10 is used for RW pages and PP11 for RO pages, and user
segment register's Kp and Ks are set to 1. This patch modifies
page protection to use PP01 for RW pages and sets user segment
registers to Kp 0 and Ks 0.
This will allow to setup Userspace write access protection by
settng Ks to 1 in the following patch.
Kernel space segment registers remain unchanged.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To implement Kernel Userspace Execution Prevention, this patch
sets NX bit on all user segments on kernel entry and clears NX bit
on all user segments on kernel exit.
Note that powerpc 601 doesn't have the NX bit, so KUEP will not
work on it. A warning is displayed at startup.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds ASM macros for saving, restoring and checking
the KUAP state, and modifies setup_32 to call them on exceptions
from kernel.
The macros are defined as empty by default for when CONFIG_PPC_KUAP
is not selected and/or for platforms which don't handle (yet) KUAP.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
syscalls are from user only, so we can account time without checking
whether returning to kernel or user as it will only be user.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Kernel Userspace Access Prevention utilises a feature of the Radix MMU
which disallows read and write access to userspace addresses. By
utilising this, the kernel is prevented from accessing user data from
outside of trusted paths that perform proper safety checks, such as
copy_{to/from}_user() and friends.
Userspace access is disabled from early boot and is only enabled when
performing an operation like copy_{to/from}_user(). The register that
controls this (AMR) does not prevent userspace from accessing itself,
so there is no need to save and restore when entering and exiting
userspace.
When entering the kernel from the kernel we save AMR and if it is not
blocking user access (because eg. we faulted doing a user access) we
reblock user access for the duration of the exception (ie. the page
fault) and then restore the AMR when returning back to the kernel.
This feature can be tested by using the lkdtm driver (CONFIG_LKDTM=y)
and performing the following:
# (echo ACCESS_USERSPACE) > [debugfs]/provoke-crash/DIRECT
If enabled, this should send SIGSEGV to the thread.
We also add paranoid checking of AMR in switch and syscall return
under CONFIG_PPC_KUAP_DEBUG.
Co-authored-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some platforms (i.e. Radix MMU) need per-CPU initialisation for KUP.
Any platforms that only want to do KUP initialisation once
globally can just check to see if they're running on the boot CPU, or
check if whatever setup they need has already been performed.
Note that this is only for 64-bit.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch implements a framework for Kernel Userspace Access
Protection.
Then subarches will have the possibility to provide their own
implementation by providing setup_kuap() and
allow/prevent_user_access().
Some platforms will need to know the area accessed and whether it is
accessed from read, write or both. Therefore source, destination and
size and handed over to the two functions.
mpe: Rename to allow/prevent rather than unlock/lock, and add
read/write wrappers. Drop the 32-bit code for now until we have an
implementation for it. Add kuap to pt_regs for 64-bit as well as
32-bit. Don't split strings, use pr_crit_ratelimited().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds a skeleton for Kernel Userspace Protection
functionnalities like Kernel Userspace Access Protection and Kernel
Userspace Execution Prevention
The subsequent implementation of KUAP for radix makes use of a MMU
feature in order to patch out assembly when KUAP is disabled or
unsupported. This won't work unless there's an entry point for KUP
support before the feature magic happens, so for PPC64 setup_kup() is
called early in setup.
On PPC32, feature_fixup() is done too early to allow the same.
Suggested-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to implement KUAP (Kernel Userspace Access Protection) on
Power9 we will be using the AMR, and therefore indirectly the
UAMOR/AMOR.
So save/restore these regs in the idle code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Without restoring the IAMR after idle, execution prevention on POWER9
with Radix MMU is overwritten and the kernel can freely execute
userspace without faulting.
This is necessary when returning from any stop state that modifies
user state, as well as hypervisor state.
To test how this fails without this patch, load the lkdtm driver and
do the following:
$ echo EXEC_USERSPACE > /sys/kernel/debug/provoke-crash/DIRECT
which won't fault, then boot the kernel with powersave=off, where it
will fault. Applying this patch will fix this.
Fixes: 3b10d0095a ("powerpc/mm/radix: Prevent kernel execution of user space")
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a flag so that the DAWR can be enabled on P9 via:
echo Y > /sys/kernel/debug/powerpc/dawr_enable_dangerous
The DAWR was previously force disabled on POWER9 in:
9654153158 powerpc: Disable DAWR in the base POWER9 CPU features
Also see Documentation/powerpc/DAWR-POWER9.txt
This is a dangerous setting, USE AT YOUR OWN RISK.
Some users may not care about a bad user crashing their box
(ie. single user/desktop systems) and really want the DAWR. This
allows them to force enable DAWR.
This flag can also be used to disable DAWR access. Once this is
cleared, all DAWR access should be cleared immediately and your
machine once again safe from crashing.
Userspace may get confused by toggling this. If DAWR is force
enabled/disabled between getting the number of breakpoints (via
PTRACE_GETHWDBGINFO) and setting the breakpoint, userspace will get an
inconsistent view of what's available. Similarly for guests.
For the DAWR to be enabled in a KVM guest, the DAWR needs to be force
enabled in the host AND the guest. For this reason, this won't work on
POWERVM as it doesn't allow the HCALL to work. Writes of 'Y' to the
dawr_enable_dangerous file will fail if the hypervisor doesn't support
writing the DAWR.
To double check the DAWR is working, run this kernel selftest:
tools/testing/selftests/powerpc/ptrace/ptrace-hwbreak.c
Any errors/failures/skips mean something is wrong.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add support to hwpoison the pages upon hitting machine check
exception.
This patch queues the address where UE is hit to percpu array
and schedules work to plumb it into memory poison infrastructure.
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
[mpe: Combine #ifdefs, drop PPC_BIT8(), and empty inline stub]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With STRICT_KERNEL_RWX enabled anything marked __init is placed at a 16M
boundary. This is necessary so that it can be repurposed later with
different permissions. However, in kernels with text larger than 16M,
this pushes early_setup past 32M, incapable of being reached by the
branch instruction.
Fix this by setting the CTR and branching there instead.
Fixes: 1e0fc9d1eb ("powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs")
Signed-off-by: Russell Currey <ruscur@russell.cc>
[mpe: Fix it to work on BE by using DOTSYM()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add the io_uring and pidfd_send_signal system calls to all architectures.
These system calls are designed to handle both native and compat tasks,
so all entries are the same across architectures, only arm-compat and
the generic tale still use an old format.
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> (s390)
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A minor build fix for 64-bit FLATMEM configs.
A fix for a boot failure on 32-bit powermacs.
My commit to fix CLOCK_MONOTONIC across Y2038 broke the 32-bit VDSO on 64-bit
kernels, ie. compat mode, which is only used on big endian.
The rewrite of the SLB code we merged in 4.20 missed the fact that the 0x380
exception is also used with the Radix MMU to report out of range accesses. This
could lead to an oops if userspace tried to read from addresses outside the user
or kernel range.
Thanks to:
Aneesh Kumar K.V, Christophe Leroy, Larry Finger, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----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=pfZc
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.1-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A minor build fix for 64-bit FLATMEM configs.
A fix for a boot failure on 32-bit powermacs.
My commit to fix CLOCK_MONOTONIC across Y2038 broke the 32-bit VDSO on
64-bit kernels, ie. compat mode, which is only used on big endian.
The rewrite of the SLB code we merged in 4.20 missed the fact that the
0x380 exception is also used with the Radix MMU to report out of range
accesses. This could lead to an oops if userspace tried to read from
addresses outside the user or kernel range.
Thanks to: Aneesh Kumar K.V, Christophe Leroy, Larry Finger, Nicholas
Piggin"
* tag 'powerpc-5.1-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Define MAX_PHYSMEM_BITS for all 64-bit configs
powerpc/64s/radix: Fix radix segment exception handling
powerpc/vdso32: fix CLOCK_MONOTONIC on PPC64
powerpc/32: Fix early boot failure with RTAS built-in
Commit 48e7b76957 ("powerpc/64s/hash: Convert SLB miss handlers to C")
broke the radix-mode segment exception handler. In radix mode, this is
exception is not an SLB miss, rather it signals that the EA is outside
the range translated by any page table.
The commit lost the radix feature alternate code patch, which can
cause faults to some EAs to kernel BUG at arch/powerpc/mm/slb.c:639!
The original radix code would send faults to slb_miss_large_addr,
which would end up faulting due to slb_addr_limit being 0. This patch
sends radix directly to do_bad_slb_fault, which is a bit clearer.
Fixes: 48e7b76957 ("powerpc/64s/hash: Convert SLB miss handlers to C")
Cc: stable@vger.kernel.org # v4.20+
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit b5b4453e79 ("powerpc/vdso64: Fix CLOCK_MONOTONIC
inconsistencies across Y2038") changed the type of wtom_clock_sec
to s64 on PPC64. Therefore, VDSO32 needs to read it with a 4 bytes
shift in order to retrieve the lower part of it.
Fixes: b5b4453e79 ("powerpc/vdso64: Fix CLOCK_MONOTONIC inconsistencies across Y2038")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 2d4f567103 ("KVM: PPC: Introduce kvm_tmp framework") adds
kvm_tmp[] into the .bss section and then free the rest of unused spaces
back to the page allocator.
kernel_init
kvm_guest_init
kvm_free_tmp
free_reserved_area
free_unref_page
free_unref_page_prepare
With DEBUG_PAGEALLOC=y, it will unmap those pages from kernel. As the
result, kmemleak scan will trigger a panic when it scans the .bss
section with unmapped pages.
This patch creates dedicated kmemleak objects for the .data, .bss and
potentially .data..ro_after_init sections to allow partial freeing via
the kmemleak_free_part() in the powerpc kvm_free_tmp() function.
Link: http://lkml.kernel.org/r/20190321171917.62049-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Qian Cai <cai@lca.pw>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Qian Cai <cai@lca.pw>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 0df977eafc ("powerpc/6xx: Don't use SPRN_SPRG2 for storing
stack pointer while in RTAS") changes the code to use a field in
thread struct to store the stack pointer while in RTAS instead of
using SPRN_SPRG2. It therefore converts all places which were
manipulating SPRN_SPRG2 to use that field. During early startup, the
zeroing of SPRN_SPRG2 has been replaced by a zeroing of that field in
thread struct. But at least in start_here, that's done wrongly because
it used the physical address of the fields while MMU is on at that
time.
So the virtual address of the field should be used instead, but in
the meantime, thread struct has already been zeroed and initialised
so we can just drop this initialisation.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Fixes: 0df977eafc ("powerpc/6xx: Don't use SPRN_SPRG2 for storing stack pointer while in RTAS")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When I updated the spectre_v2 reporting to handle software count cache
flush I got the logic wrong when there's no software count cache
enabled at all.
The result is that on systems with the software count cache flush
disabled we print:
Mitigation: Indirect branch cache disabled, Software count cache flush
Which correctly indicates that the count cache is disabled, but
incorrectly says the software count cache flush is enabled.
The root of the problem is that we are trying to handle all
combinations of options. But we know now that we only expect to see
the software count cache flush enabled if the other options are false.
So split the two cases, which simplifies the logic and fixes the bug.
We were also missing a space before "(hardware accelerated)".
The result is we see one of:
Mitigation: Indirect branch serialisation (kernel only)
Mitigation: Indirect branch cache disabled
Mitigation: Software count cache flush
Mitigation: Software count cache flush (hardware accelerated)
Fixes: ee13cb249f ("powerpc/64s: Add support for software count cache flush")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Not only the 603 but all 6xx need SPRN_SPRG_PGDIR to be initialised at
startup. This patch move it from __setup_cpu_603() to start_here()
and __secondary_start(), close to the initialisation of SPRN_THREAD.
Previously, virt addr of PGDIR was retrieved from thread struct.
Now that it is the phys addr which is stored in SPRN_SPRG_PGDIR,
hash_page() shall not convert it to phys anymore.
This patch removes the conversion.
Fixes: 93c4a162b0 ("powerpc/6xx: Store PGDIR physical address in a SPRG")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Jakub Drnec reported:
Setting the realtime clock can sometimes make the monotonic clock go
back by over a hundred years. Decreasing the realtime clock across
the y2k38 threshold is one reliable way to reproduce. Allegedly this
can also happen just by running ntpd, I have not managed to
reproduce that other than booting with rtc at >2038 and then running
ntp. When this happens, anything with timers (e.g. openjdk) breaks
rather badly.
And included a test case (slightly edited for brevity):
#define _POSIX_C_SOURCE 199309L
#include <stdio.h>
#include <time.h>
#include <stdlib.h>
#include <unistd.h>
long get_time(void) {
struct timespec tp;
clock_gettime(CLOCK_MONOTONIC, &tp);
return tp.tv_sec + tp.tv_nsec / 1000000000;
}
int main(void) {
long last = get_time();
while(1) {
long now = get_time();
if (now < last) {
printf("clock went backwards by %ld seconds!\n", last - now);
}
last = now;
sleep(1);
}
return 0;
}
Which when run concurrently with:
# date -s 2040-1-1
# date -s 2037-1-1
Will detect the clock going backward.
The root cause is that wtom_clock_sec in struct vdso_data is only a
32-bit signed value, even though we set its value to be equal to
tk->wall_to_monotonic.tv_sec which is 64-bits.
Because the monotonic clock starts at zero when the system boots the
wall_to_montonic.tv_sec offset is negative for current and future
dates. Currently on a freshly booted system the offset will be in the
vicinity of negative 1.5 billion seconds.
However if the wall clock is set past the Y2038 boundary, the offset
from wall to monotonic becomes less than negative 2^31, and no longer
fits in 32-bits. When that value is assigned to wtom_clock_sec it is
truncated and becomes positive, causing the VDSO assembly code to
calculate CLOCK_MONOTONIC incorrectly.
That causes CLOCK_MONOTONIC to jump ahead by ~4 billion seconds which
it is not meant to do. Worse, if the time is then set back before the
Y2038 boundary CLOCK_MONOTONIC will jump backward.
We can fix it simply by storing the full 64-bit offset in the
vdso_data, and using that in the VDSO assembly code. We also shuffle
some of the fields in vdso_data to avoid creating a hole.
The original commit that added the CLOCK_MONOTONIC support to the VDSO
did actually use a 64-bit value for wtom_clock_sec, see commit
a7f290dad3 ("[PATCH] powerpc: Merge vdso's and add vdso support to
32 bits kernel") (Nov 2005). However just 3 days later it was
converted to 32-bits in commit 0c37ec2aa8 ("[PATCH] powerpc: vdso
fixes (take #2)"), and the bug has existed since then AFAICS.
Fixes: 0c37ec2aa8 ("[PATCH] powerpc: vdso fixes (take #2)")
Cc: stable@vger.kernel.org # v2.6.15+
Link: http://lkml.kernel.org/r/HaC.ZfES.62bwlnvAvMP.1STMMj@seznam.cz
Reported-by: Jakub Drnec <jaydee@email.cz>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
One fix to prevent runtime allocation of 16GB pages when running in a VM (as
opposed to bare metal), because it doesn't work.
A small fix to our recently added KCOV support to exempt some more code from
being instrumented.
Plus a few minor build fixes, a small dead code removal and a defconfig update.
Thanks to:
Alexey Kardashevskiy, Aneesh Kumar K.V, Christophe Leroy, Jason Yan, Joel
Stanley, Mahesh Salgaonkar, Mathieu Malaterre.
-----BEGIN PGP SIGNATURE-----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=6cp4
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix to prevent runtime allocation of 16GB pages when running in a
VM (as opposed to bare metal), because it doesn't work.
A small fix to our recently added KCOV support to exempt some more
code from being instrumented.
Plus a few minor build fixes, a small dead code removal and a
defconfig update.
Thanks to: Alexey Kardashevskiy, Aneesh Kumar K.V, Christophe Leroy,
Jason Yan, Joel Stanley, Mahesh Salgaonkar, Mathieu Malaterre"
* tag 'powerpc-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Include <asm/nmi.h> header file to fix a warning
powerpc/powernv: Fix compile without CONFIG_TRACEPOINTS
powerpc/mm: Disable kcov for SLB routines
powerpc: remove dead code in head_fsl_booke.S
powerpc/configs: Sync skiroot defconfig
powerpc/hugetlb: Don't do runtime allocation of 16G pages in LPAR configuration
Make sure to include <asm/nmi.h> to provide the following prototype:
hv_nmi_check_nonrecoverable.
Remove the following warning treated as error (W=1):
arch/powerpc/kernel/traps.c:393:6: error: no previous prototype for 'hv_nmi_check_nonrecoverable'
Fixes: ccd477028a ("powerpc/64s: Fix HV NMI vs HV interrupt recoverability test")
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add check for the return value of memblock_alloc*() functions and call
panic() in case of error. The panic message repeats the one used by
panicing memblock allocators with adjustment of parameters to include
only relevant ones.
The replacement was mostly automated with semantic patches like the one
below with manual massaging of format strings.
@@
expression ptr, size, align;
@@
ptr = memblock_alloc(size, align);
+ if (!ptr)
+ panic("%s: Failed to allocate %lu bytes align=0x%lx\n", __func__, size, align);
[anders.roxell@linaro.org: use '%pa' with 'phys_addr_t' type]
Link: http://lkml.kernel.org/r/20190131161046.21886-1-anders.roxell@linaro.org
[rppt@linux.ibm.com: fix format strings for panics after memblock_alloc]
Link: http://lkml.kernel.org/r/1548950940-15145-1-git-send-email-rppt@linux.ibm.com
[rppt@linux.ibm.com: don't panic if the allocation in sparse_buffer_init fails]
Link: http://lkml.kernel.org/r/20190131074018.GD28876@rapoport-lnx
[akpm@linux-foundation.org: fix xtensa printk warning]
Link: http://lkml.kernel.org/r/1548057848-15136-20-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Guo Ren <ren_guo@c-sky.com> [c-sky]
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390]
Reviewed-by: Juergen Gross <jgross@suse.com> [Xen]
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The memblock_alloc_base() function tries to allocate a memory up to the
limit specified by its max_addr parameter and panics if the allocation
fails. Replace its usage with memblock_phys_alloc_range() and make the
callers check the return value and panic in case of error.
Link: http://lkml.kernel.org/r/1548057848-15136-10-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com> [c-sky]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Juergen Gross <jgross@suse.com> [Xen]
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since only the virtual address of allocated blocks is used, lets use
functions returning directly virtual address.
Those functions have the advantage of also zeroing the block.
[rppt@linux.ibm.com: powerpc: remove duplicated alloc_stack() function]
Link: http://lkml.kernel.org/r/20190226064032.GA5873@rapoport-lnx
[rppt@linux.ibm.com: updated error message in alloc_stack() to be more verbose]
[rppt@linux.ibm.com: convereted several additional call sites ]
Link: http://lkml.kernel.org/r/1548057848-15136-3-git-send-email-rppt@linux.ibm.com
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com> [c-sky]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Juergen Gross <jgross@suse.com> [Xen]
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge more updates from Andrew Morton:
- some of the rest of MM
- various misc things
- dynamic-debug updates
- checkpatch
- some epoll speedups
- autofs
- rapidio
- lib/, lib/lzo/ updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (83 commits)
samples/mic/mpssd/mpssd.h: remove duplicate header
kernel/fork.c: remove duplicated include
include/linux/relay.h: fix percpu annotation in struct rchan
arch/nios2/mm/fault.c: remove duplicate include
unicore32: stop printing the virtual memory layout
MAINTAINERS: fix GTA02 entry and mark as orphan
mm: create the new vm_fault_t type
arm, s390, unicore32: remove oneliner wrappers for memblock_alloc()
arch: simplify several early memory allocations
openrisc: simplify pte_alloc_one_kernel()
sh: prefer memblock APIs returning virtual address
microblaze: prefer memblock API returning virtual address
powerpc: prefer memblock APIs returning virtual address
lib/lzo: separate lzo-rle from lzo
lib/lzo: implement run-length encoding
lib/lzo: fast 8-byte copy on arm64
lib/lzo: 64-bit CTZ on arm64
lib/lzo: tidy-up ifdefs
ipc/sem.c: replace kvmalloc/memset with kvzalloc and use struct_size
ipc: annotate implicit fall through
...
There are several early memory allocations in arch/ code that use
memblock_phys_alloc() to allocate memory, convert the returned physical
address to the virtual address and then set the allocated memory to
zero.
Exactly the same behaviour can be achieved simply by calling
memblock_alloc(): it allocates the memory in the same way as
memblock_phys_alloc(), then it performs the phys_to_virt() conversion
and clears the allocated memory.
Replace the longer sequence with a simpler call to memblock_alloc().
Link: http://lkml.kernel.org/r/1546248566-14910-6-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "memblock: simplify several early memory allocation", v4.
These patches simplify some of the early memory allocations by replacing
usage of older memblock APIs with newer and shinier ones.
Quite a few places in the arch/ code allocated memory using a memblock
API that returns a physical address of the allocated area, then
converted this physical address to a virtual one and then used memset(0)
to clear the allocated range.
More recent memblock APIs do all the three steps in one call and their
usage simplifies the code.
It's important to note that regardless of API used, the core allocation
is nearly identical for any set of memblock allocators: first it tries
to find a free memory with all the constraints specified by the caller
and then falls back to the allocation with some or all constraints
disabled.
The first three patches perform the conversion of call sites that have
exact requirements for the node and the possible memory range.
The fourth patch is a bit one-off as it simplifies openrisc's
implementation of pte_alloc_one_kernel(), and not only the memblock
usage.
The fifth patch takes care of simpler cases when the allocation can be
satisfied with a simple call to memblock_alloc().
The sixth patch removes one-liner wrappers for memblock_alloc on arm and
unicore32, as suggested by Christoph.
This patch (of 6):
There are a several places that allocate memory using memblock APIs that
return a physical address, convert the returned address to the virtual
address and frequently also memset(0) the allocated range.
Update these places to use memblock allocators already returning a
virtual address. Use memblock functions that clear the allocated memory
instead of calling memset(0) where appropriate.
The calls to memblock_alloc_base() that were not followed by memset(0)
are replaced with memblock_alloc_try_nid_raw(). Since the latter does
not panic() when the allocation fails, the appropriate panic() calls are
added to the call sites.
Link: http://lkml.kernel.org/r/1546248566-14910-2-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mark Salter <msalter@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Notable changes:
- Enable THREAD_INFO_IN_TASK to move thread_info off the stack.
- A big series from Christoph reworking our DMA code to use more of the generic
infrastructure, as he said:
"This series switches the powerpc port to use the generic swiotlb and
noncoherent dma ops, and to use more generic code for the coherent direct
mapping, as well as removing a lot of dead code."
- Increase our vmalloc space to 512T with the Hash MMU on modern CPUs, allowing
us to support machines with larger amounts of total RAM or distance between
nodes.
- Two series from Christophe, one to optimise TLB miss handlers on 6xx, and
another to optimise the way STRICT_KERNEL_RWX is implemented on some 32-bit
CPUs.
- Support for KCOV coverage instrumentation which means we can run syzkaller
and discover even more bugs in our code.
And as always many clean-ups, reworks and minor fixes etc.
Thanks to:
Alan Modra, Alexey Kardashevskiy, Alistair Popple, Andrea Arcangeli, Andrew
Donnellan, Aneesh Kumar K.V, Aravinda Prasad, Balbir Singh, Brajeswar Ghosh,
Breno Leitao, Christian Lamparter, Christian Zigotzky, Christophe Leroy,
Christoph Hellwig, Corentin Labbe, Daniel Axtens, David Gibson, Diana Craciun,
Firoz Khan, Gustavo A. R. Silva, Igor Stoppa, Joe Lawrence, Joel Stanley,
Jonathan Neuschäfer, Jordan Niethe, Laurent Dufour, Madhavan Srinivasan, Mahesh
Salgaonkar, Mark Cave-Ayland, Masahiro Yamada, Mathieu Malaterre, Matteo Croce,
Meelis Roos, Michael W. Bringmann, Nathan Chancellor, Nathan Fontenot, Nicholas
Piggin, Nick Desaulniers, Nicolai Stange, Oliver O'Halloran, Paul Mackerras,
Peter Xu, PrasannaKumar Muralidharan, Qian Cai, Rashmica Gupta, Reza Arbab,
Robert P. J. Day, Russell Currey, Sabyasachi Gupta, Sam Bobroff, Sandipan Das,
Sergey Senozhatsky, Souptick Joarder, Stewart Smith, Tyrel Datwyler, Vaibhav
Jain, YueHaibing.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcgRJlAAoJEFHr6jzI4aWAL9oP+gPlrZgyaAg/51lmubLtlbtk
QuGU8EiuJZoJD1OHrMPtppBOY7rQZOxJe58AoPig8wTvs+j/TxJ25fmiZncnf5U2
PC8QAjbj0UmQHgy+K30sUeOnDg9tdkHKHJ5/ecjJcvykkqsjyMnV7biFQ1cOA0HT
LflXHEEtiG9P9u7jZoAhtnfpgn1/l9mhTYMe26J1fqvC0164qMDFaXDTQXyDfyvG
gmuqccGMawSk7IdagmQxwXtwyfwOnarmGn+n31XKRejApGZ/pjiEA23JOJOaJcia
m76Jy3roao6sEtCUNpBFXEtwOy9POy3OiGy6yg/9896tDMvG84OuO6ltV1nFGawL
PmwE+ug63L4g/HWxZyAeb26T2oTTp/YIaKQPtsq4d286pvg/qr2KPNzFoAEhmJqU
yLrebv276pVeiLpLmCLPvcPj9t76vWKZaUm0FoE+zUDg7Rl7Alow8A/c4tdjOI6y
QwpbCiYseyiJ32lCZZdbN7Cy6+iM6vb3i1oNKc8MVqhBGTwLJnTU0ruPBSvCaRvD
NoQWO1RWpNu/BuivuLEKS9q3AoxenGwiqowxGhdVmI3Oc9jGWcEYlduR00VDYPVp
/RCfwtTY5NyC++h5cnbz8aLJ1hBXG5m79CXfprV+zPWeiLPCaMT6w9Y5QUS2wqA+
EZ734NknDJOjaHc4cGdZ
=Z9bb
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Enable THREAD_INFO_IN_TASK to move thread_info off the stack.
- A big series from Christoph reworking our DMA code to use more of
the generic infrastructure, as he said:
"This series switches the powerpc port to use the generic swiotlb
and noncoherent dma ops, and to use more generic code for the
coherent direct mapping, as well as removing a lot of dead
code."
- Increase our vmalloc space to 512T with the Hash MMU on modern
CPUs, allowing us to support machines with larger amounts of total
RAM or distance between nodes.
- Two series from Christophe, one to optimise TLB miss handlers on
6xx, and another to optimise the way STRICT_KERNEL_RWX is
implemented on some 32-bit CPUs.
- Support for KCOV coverage instrumentation which means we can run
syzkaller and discover even more bugs in our code.
And as always many clean-ups, reworks and minor fixes etc.
Thanks to: Alan Modra, Alexey Kardashevskiy, Alistair Popple, Andrea
Arcangeli, Andrew Donnellan, Aneesh Kumar K.V, Aravinda Prasad, Balbir
Singh, Brajeswar Ghosh, Breno Leitao, Christian Lamparter, Christian
Zigotzky, Christophe Leroy, Christoph Hellwig, Corentin Labbe, Daniel
Axtens, David Gibson, Diana Craciun, Firoz Khan, Gustavo A. R. Silva,
Igor Stoppa, Joe Lawrence, Joel Stanley, Jonathan Neuschäfer, Jordan
Niethe, Laurent Dufour, Madhavan Srinivasan, Mahesh Salgaonkar, Mark
Cave-Ayland, Masahiro Yamada, Mathieu Malaterre, Matteo Croce, Meelis
Roos, Michael W. Bringmann, Nathan Chancellor, Nathan Fontenot,
Nicholas Piggin, Nick Desaulniers, Nicolai Stange, Oliver O'Halloran,
Paul Mackerras, Peter Xu, PrasannaKumar Muralidharan, Qian Cai,
Rashmica Gupta, Reza Arbab, Robert P. J. Day, Russell Currey,
Sabyasachi Gupta, Sam Bobroff, Sandipan Das, Sergey Senozhatsky,
Souptick Joarder, Stewart Smith, Tyrel Datwyler, Vaibhav Jain,
YueHaibing"
* tag 'powerpc-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (200 commits)
powerpc/32: Clear on-stack exception marker upon exception return
powerpc: Remove export of save_stack_trace_tsk_reliable()
powerpc/mm: fix "section_base" set but not used
powerpc/mm: Fix "sz" set but not used warning
powerpc/mm: Check secondary hash page table
powerpc: remove nargs from __SYSCALL
powerpc/64s: Fix unrelocated interrupt trampoline address test
powerpc/powernv/ioda: Fix locked_vm counting for memory used by IOMMU tables
powerpc/fsl: Fix the flush of branch predictor.
powerpc/powernv: Make opal log only readable by root
powerpc/xmon: Fix opcode being uninitialized in print_insn_powerpc
powerpc/powernv: move OPAL call wrapper tracing and interrupt handling to C
powerpc/64s: Fix data interrupts vs d-side MCE reentrancy
powerpc/64s: Prepare to handle data interrupts vs d-side MCE reentrancy
powerpc/64s: system reset interrupt preserve HSRRs
powerpc/64s: Fix HV NMI vs HV interrupt recoverability test
powerpc/mm/hash: Handle mmap_min_addr correctly in get_unmapped_area topdown search
powerpc/hugetlb: Handle mmap_min_addr correctly in get_unmapped_area callback
selftests/powerpc: Remove duplicate header
powerpc sstep: Add support for modsd, modud instructions
...
Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they asked
me to do as the MEI driver is starting to interact with the i915 driver,
and it needed some coordination. All of those patches have been
properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+dPQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym1fACgvpZAxjNzoRQJ6f06tc8ujtPk9rUAnR+tCtrZ
9e3l7H76oe33o96Qjhor
=8A2k
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they
asked me to do as the MEI driver is starting to interact with the i915
driver, and it needed some coordination. All of those patches have
been properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time"
* tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (219 commits)
habanalabs: adjust Kconfig to fix build errors
habanalabs: use %px instead of %p in error print
habanalabs: use do_div for 64-bit divisions
intel_th: gth: Fix an off-by-one in output unassigning
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: use NULL to initialize array of pointers
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: soft-reset device if context-switch fails
habanalabs: print pointer using %p
habanalabs: fix memory leak with CBs with unaligned size
habanalabs: return correct error code on MMU mapping failure
habanalabs: add comments in uapi/misc/habanalabs.h
habanalabs: extend QMAN0 job timeout
habanalabs: set DMA0 completion to SOB 1007
habanalabs: fix validation of WREG32 to DMA completion
habanalabs: fix mmu cache registers init
habanalabs: disable CPU access on timeouts
habanalabs: add MMU DRAM default page mapping
habanalabs: Dissociate RAZWI info from event types
misc/habanalabs: adjust Kconfig to fix build errors
...
Merge misc updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (159 commits)
tools/testing/selftests/proc/proc-self-syscall.c: remove duplicate include
proc: more robust bulk read test
proc: test /proc/*/maps, smaps, smaps_rollup, statm
proc: use seq_puts() everywhere
proc: read kernel cpu stat pointer once
proc: remove unused argument in proc_pid_lookup()
fs/proc/thread_self.c: code cleanup for proc_setup_thread_self()
fs/proc/self.c: code cleanup for proc_setup_self()
proc: return exit code 4 for skipped tests
mm,mremap: bail out earlier in mremap_to under map pressure
mm/sparse: fix a bad comparison
mm/memory.c: do_fault: avoid usage of stale vm_area_struct
writeback: fix inode cgroup switching comment
mm/huge_memory.c: fix "orig_pud" set but not used
mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC
mm/memcontrol.c: fix bad line in comment
mm/cma.c: cma_declare_contiguous: correct err handling
mm/page_ext.c: fix an imbalance with kmemleak
mm/compaction: pass pgdat to too_many_isolated() instead of zone
mm: remove zone_lru_lock() function, access ->lru_lock directly
...
The VDSO is part of the kernel image and therefore the struct pages are
marked as reserved during boot.
As we install a special mapping, the actual struct pages will never be
exposed to MM via the page tables. We can therefore leave the pages
marked as reserved.
Link: http://lkml.kernel.org/r/20190114125903.24845-4-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Replace all open encodings for NUMA_NO_NODE", v3.
All these places for replacement were found by running the following
grep patterns on the entire kernel code. Please let me know if this
might have missed some instances. This might also have replaced some
false positives. I will appreciate suggestions, inputs and review.
1. git grep "nid == -1"
2. git grep "node == -1"
3. git grep "nid = -1"
4. git grep "node = -1"
This patch (of 2):
At present there are multiple places where invalid node number is
encoded as -1. Even though implicitly understood it is always better to
have macros in there. Replace these open encodings for an invalid node
number with the global macro NUMA_NO_NODE. This helps remove NUMA
related assumptions like 'invalid node' from various places redirecting
them to a common definition.
Link: http://lkml.kernel.org/r/1545127933-10711-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [ixgbe]
Acked-by: Jens Axboe <axboe@kernel.dk> [mtip32xx]
Acked-by: Vinod Koul <vkoul@kernel.org> [dmaengine.c]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Doug Ledford <dledford@redhat.com> [drivers/infiniband]
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code is dead. Just remove it.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As tglx points out, there are no in-tree module users of
save_stack_trace_tsk_reliable() and its x86 counterpart is not
exported, so remove the powerpc symbol export.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The __SYSCALL macro's arguments are system call number,
system call entry name and number of arguments for the
system call.
Argument- nargs in __SYSCALL(nr, entry, nargs) is neither
calculated nor used anywhere. So it would be better to
keep the implementaion as __SYSCALL(nr, entry). This will
unifies the implementation with some other architetures
too.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The recent commit got this test wrong, it declared the assembler
symbols the wrong way, and also used the wrong symbol name
(xxx_start rather than start_xxx, see asm/head-64.h).
Fixes: ccd477028a ("powerpc/64s: Fix HV NMI vs HV interrupt recoverability test")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The commit identified below adds MC_BTB_FLUSH macro only when
CONFIG_PPC_FSL_BOOK3E is defined. This results in the following error
on some configs (seen several times with kisskb randconfig_defconfig)
arch/powerpc/kernel/exceptions-64e.S:576: Error: Unrecognized opcode: `mc_btb_flush'
make[3]: *** [scripts/Makefile.build:367: arch/powerpc/kernel/exceptions-64e.o] Error 1
make[2]: *** [scripts/Makefile.build:492: arch/powerpc/kernel] Error 2
make[1]: *** [Makefile:1043: arch/powerpc] Error 2
make: *** [Makefile:152: sub-make] Error 2
This patch adds a blank definition of MC_BTB_FLUSH for other cases.
Fixes: 10c5e83afd ("powerpc/fsl: Flush the branch predictor at each kernel entry (64bit)")
Cc: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Handlers for interrupts that set DAR / DSISR, set MSR[RI] before those
SPRs are read. If a d-side machine check hits in this window, DAR /
DSISR will be clobbered silently, leading to random corruption.
Fix this by having handlers save those registers before setting MSR[RI].
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A subsequent fix for data interrupts (those that set DAR / DSISR)
requires some interrupt macros to be open-coded, and also requires
the 0x300 interrupt handler to be moved out-of-line.
This patch does that without changing behaviour, which makes the later
fix a smaller change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Code that uses HSRR registers is not required to clear MSR[RI] by
convention, however the system reset NMI itself may use HSRR
registers (e.g., to call OPAL) and clobber them.
Rather than introduce the requirement to clear RI in order to use
HSRRs, have system reset interrupt save and restore HSRRs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
HV interrupts that use HSRR registers do not enter with MSR[RI] clear,
but their entry code is not recoverable vs NMI, due to shared use of
HSPRG1 as a scratch register to save r13.
This means that a system reset or machine check that hits in HSRR
interrupt entry can cause r13 to be silently corrupted.
Fix this by marking NMIs non-recoverable if they land in HV interrupt
ranges.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some stack pointers used to also be thread_info pointers
and were called tp. Now that they are only stack pointers,
rename them sp.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that current_thread_info is located at the beginning of 'current'
task struct, CURRENT_THREAD_INFO macro is not really needed any more.
This patch replaces it by loads of the value at PACA_THREAD_INFO(r13).
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Add PACA_THREAD_INFO rather than using PACACURRENT]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that thread_info is similar to task_struct, its address is in r2
so CURRENT_THREAD_INFO() macro is useless. This patch removes it.
This patch also moves the 'tovirt(r2, r2)' down just before the
reactivation of MMU translation, so that we keep the physical address
of 'current' in r2 until then. It avoids a few calls to tophys().
At the same time, as the 'cpu' field is not anymore in thread_info,
TI_CPU is renamed TASK_CPU by this patch.
It also allows to get rid of a couple of
'#ifdef CONFIG_VIRT_CPU_ACCOUNTING_NATIVE' as ACCOUNT_CPU_USER_ENTRY()
and ACCOUNT_CPU_USER_EXIT() are empty when
CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not defined.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Fix a missed conversion of TI_CPU idle_6xx.S]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The table of pointers 'current_set' has been used for retrieving
the stack and current. They used to be thread_info pointers as
they were pointing to the stack and current was taken from the
'task' field of the thread_info.
Now, the pointers of 'current_set' table are now both pointers
to task_struct and pointers to thread_info.
As they are used to get current, and the stack pointer is
retrieved from current's stack field, this patch changes
their type to task_struct, and renames secondary_ti to
secondary_current.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
thread_info is not anymore in the stack, so the entire stack
can now be used.
There is also no risk anymore of corrupting task_cpu(p) with a
stack overflow so the patch removes the test.
When doing this, an explicit test for NULL stack pointer is
needed in validate_sp() as it is not anymore implicitely covered
by the sizeof(thread_info) gap.
In the meantime, with the previous patch all pointers to the stacks
are not anymore pointers to thread_info so this patch changes them
to void*
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch activates CONFIG_THREAD_INFO_IN_TASK which
moves the thread_info into task_struct.
Moving thread_info into task_struct has the following advantages:
- It protects thread_info from corruption in the case of stack
overflows.
- Its address is harder to determine if stack addresses are leaked,
making a number of attacks more difficult.
This has the following consequences:
- thread_info is now located at the beginning of task_struct.
- The 'cpu' field is now in task_struct, and only exists when
CONFIG_SMP is active.
- thread_info doesn't have anymore the 'task' field.
This patch:
- Removes all recopy of thread_info struct when the stack changes.
- Changes the CURRENT_THREAD_INFO() macro to point to current.
- Selects CONFIG_THREAD_INFO_IN_TASK.
- Modifies raw_smp_processor_id() to get ->cpu from current without
including linux/sched.h to avoid circular inclusion and without
including asm/asm-offsets.h to avoid symbol names duplication
between ASM constants and C constants.
- Modifies klp_init_thread_info() to take a task_struct pointer
argument.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add task_stack.h to livepatch.h to fix build fails]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure CURRENT_THREAD_INFO() is used with r1 which is the virtual
address of the stack, in order to ease the switch to r2 when we enable
THREAD_INFO_IN_TASK, as we have no register having the phys address of
current.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than using the thread info use task_stack_page() to initialise
paca->kstack, that way it will work with THREAD_INFO_IN_TASK.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update a few comments that talk about current_thread_info() in
preparation for THREAD_INFO_IN_TASK.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have a few places that use current_thread_info()->task to access
current. This won't work with THREAD_INFO_IN_TASK so fix them now.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A few places use CURRENT_THREAD_INFO, or the C version, to find the
stack. This will no longer work with THREAD_INFO_IN_TASK so change
them to find the stack in other ways.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The purpose of the pointer given to call_do_softirq() and
call_do_irq() is to point the new stack. Currently that's the same
thing as the thread_info, but won't be with THREAD_INFO_IN_TASK.
So change the parameter to void* and rename it 'sp'.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch renames THREAD_INFO to TASK_STACK, because it is in fact
the offset of the pointer to the stack in task_struct so this pointer
will not be impacted by the move of THREAD_INFO.
Also make it available on 64-bit, as we'll need it there when we
activate THREAD_INFO_IN_TASK.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Make available on 64-bit]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[text copied from commit 9bbd4c56b0
("arm64: prep stack walkers for THREAD_INFO_IN_TASK")]
When CONFIG_THREAD_INFO_IN_TASK is selected, task stacks may be freed
before a task is destroyed. To account for this, the stacks are
refcounted, and when manipulating the stack of another task, it is
necessary to get/put the stack to ensure it isn't freed and/or re-used
while we do so.
This patch reworks the powerpc stack walking code to account for this.
When CONFIG_THREAD_INFO_IN_TASK is not selected these perform no
refcounting, and this should only be a structural change that does not
affect behaviour.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Move try_get_task_stack() below tsk == NULL check in show_stack()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When moving to CONFIG_THREAD_INFO_IN_TASK, the thread_info 'cpu' field
gets moved into task_struct and only defined when CONFIG_SMP is set.
This patch ensures that TI_CPU is only used when CONFIG_SMP is set and
that task_struct 'cpu' field is not used directly out of SMP code.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since only the virtual address of allocated blocks is used,
lets use functions returning directly virtual address.
Those functions have the advantage of also zeroing the block.
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In __secondary_start() we load the thread_info of the idle task of the
secondary CPU from current_set[cpu], and then convert it into a stack
pointer before storing that back to paca->kstack.
As pointed out in commit f761622e59 ("powerpc: Initialise
paca->kstack before early_setup_secondary") it's important that we
initialise paca->kstack before calling the MMU setup code, in
particular slb_initialize(), because it will bolt the SLB entry for
the kstack into the SLB.
However we have already setup paca->kstack in cpu_idle_thread_init(),
since commit 3b5750644b ("[POWERPC] Bolt in SLB entry for kernel
stack on secondary cpus") (May 2008).
It's also in cpu_idle_thread_init() that we initialise current_set[cpu]
with the thread_info pointer, so there is no issue of the timing being
different between the two.
Therefore the initialisation of paca->kstack in __setup_secondary() is
completely redundant, so remove it.
This has the added benefit of removing code that runs in real mode,
and is therefore restricted by the RMO, and so opens the way for us to
enable THREAD_INFO_IN_TASK.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently in system_call_exit() we have an optimisation where we
disable MSR_RI (recoverable interrupt) and MSR_EE (external interrupt
enable) in a single mtmsrd instruction.
Unfortunately this will no longer work with THREAD_INFO_IN_TASK,
because then the load of TI_FLAGS might fault and faulting with MSR_RI
clear is treated as an unrecoverable exception which leads to a
panic().
So change the code to only clear MSR_EE prior to loading TI_FLAGS,
leaving the clear of MSR_RI until later. We have some latitude in
where do the clear of MSR_RI. A bit of experimentation has shown that
this location gives the least slow down.
This still causes a noticeable slow down in our null_syscall
performance. On a Power9 DD2.2:
Before After Delta Delta %
955 cycles 999 cycles -44 -4.6%
On the plus side this does simplify the code somewhat, because we
don't have to reenable MSR_RI on the restore_math() or
syscall_exit_work() paths which was necessitated previously by the
optimisation.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
kcov provides kernel coverage data that's useful for fuzzing tools like
syzkaller.
Wire up kcov support on powerpc. Disable kcov instrumentation on the same
files where we currently disable gcov and UBSan instrumentation, plus some
additional exclusions which appear necessary to boot on book3e machines.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Daniel Axtens <dja@axtens.net> # e6500
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On 8xx, large pages (512kb or 8M) are used to map kernel linear
memory. Aligning to 8M reduces TLB misses as only 8M pages are used
in that case. We make 8M the default for data.
This patchs allows the user to do it via Kconfig.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch implements handling of STRICT_KERNEL_RWX with
large TLBs directly in the TLB miss handlers.
To do so, etext and sinittext are aligned on 512kB boundaries
and the miss handlers use 512kB pages instead of 8Mb pages for
addresses close to the boundaries.
It sets RO PP flags for addresses under sinittext.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
setibat() and clearibat() allows to manipulate IBATs independently
of DBATs.
update_bats() allows to update bats after init. This is done
with MMU off.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_STRICT_KERNEL_RWX requires a special alignment
for DATA for some subarches. Today it is just defined
as an #ifdef in vmlinux.lds.S
In order to get more flexibility, this patch moves the
definition of this alignment in Kconfig
On some subarches, CONFIG_STRICT_KERNEL_RWX will
require a special alignment of _etext.
This patch also adds a configuration item for it in Kconfig
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the time being, initial MMU setup allows 24 Mbytes
of DATA and 8 Mbytes of code.
Some debug setup like CONFIG_KASAN generate huge
kernels with text size over the 8M limit and data over the
24 Mbytes limit.
Here is an 8xx kernel compiled with CONFIG_KASAN_INLINE for
one of my boards:
[root@po16846vm linux-powerpc]# size -x vmlinux
text data bss dec hex filename
0x111019c 0x41b0d4 0x490de0 26984528 19bc050 vmlinux
This patch maps up to 32 Mbytes code based on _einittext symbol
and allows 32 Mbytes of memory instead of 24.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
40x/booke have another path to reach 3f from transfer_to_handler,
make sure it also calls ACCOUNT_CPU_USER_ENTRY() when
CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is selected.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For pages without _PAGE_USER, PP field is 00
For pages with _PAGE_USER, PP field is 10 for RW and 11 for RO.
This patch sets _PAGE_USER to 0x002 and _PAGE_RW to 0x001
is order to simplify TLB handling by reducing amount of shifts.
The location of _PAGE_PRESENT and _PAGE_HASHPTE doesn't matter
as they are only SW related flags.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PAGE_ACCESSED is only needed for CONFIG_SWAP. When CONFIG_SWAP
is not set, just ignore it. If CONFIG_SWAP is set and PAGE_ACCESSED
is not, let's take a minor fault.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PP bits take user access into account, so no need to check _PAGE_USER
here. A DSI or ISI will be generated if needed.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PAGE_DIRTY corresponds to the C bit. If writing on
a page for which the C bit is not set, a DataStoreTLBMiss
is generated. No need to check it in DataLoadTLBMiss.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
_PAGE_RW and _PAGE_DIRTY do not matter for ITLB misses.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ITLB miss on kernel pages only occur with CONFIG_MODULES and
CONFIG_DEBUG_PAGEALLOC.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit c62ce9ef97 ("powerpc: remove remaining bits from
CONFIG_APUS"), tophys() has become a pure constant operation.
PAGE_OFFSET is known at compile time so the physical address
can be builtin directly.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use SPRN_SPRG2 to store the current thread PGDIR and
avoid reading thread_struct.pgdir at every TLB miss.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When calling RTAS, the stack pointer is stored in SPRN_SPRG2
in order to be able to restore it in case of machine check in RTAS.
As machine check is not a perfomance critical path, this patch
frees SPRN_SPRG2 by using a field in thread struct instead.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no reason to re-read each time the pointer at
location 0xf0 as it is fixed and known.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Looks like book3s/32 doesn't set RI on machine check, so
checking RI before calling die() will always be fatal
allthought this is not an issue in most cases.
Fixes: b96672dd84 ("powerpc: Machine check interrupt is a non-maskable interrupt")
Fixes: daf00ae71d ("powerpc/traps: restore recoverability of machine_check interrupts")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
MSR[RI] has already been cleared a few lines above.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When no machine description matches, display it clearly
before looping forever.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In cpufeatures_process_feature(), if a provided CPU feature is unknown and
enable_unknown is false, we erroneously print that the feature is being
enabled and return true, even though no feature has been enabled, and
may also set feature bits based on the last entry in the match table.
Fix this so that we only set feature bits from the match table if we have
actually enabled a feature from that table, and when failing to enable an
unknown feature, always print the "not enabling" message and return false.
Coincidentally, some older gccs (<GCC 7), when invoked with
-fsanitize-coverage=trace-pc, cause a spurious uninitialised variable
warning in this function:
arch/powerpc/kernel/dt_cpu_ftrs.c: In function ‘cpufeatures_process_feature’:
arch/powerpc/kernel/dt_cpu_ftrs.c:686:7: warning: ‘m’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (m->cpu_ftr_bit_mask)
An upcoming patch will enable support for kcov, which requires this option.
This patch avoids the warning.
Fixes: 5a61ef74f2 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Reported-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[ajd: add commit message]
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
The xmon debugger IPI handler waits in the callback function while
xmon is still active. This means they don't complete the IPI, and the
initiator always times out waiting for them.
Things manage to work after the timeout because there is some fallback
logic to keep NMI IPI state sane in case of the timeout, but this is a
bit ugly.
This patch changes NMI IPI back to half-asynchronous (i.e., wait for
everyone to call in, do not wait for IPI function to complete), but
the complexity is avoided by going one step further and allowing new
IPIs to be issued before the IPI functions to all complete.
If synchronization against that is required, it is left up to the
caller, but current callers don't require that. In fact with the
timeout handling, callers must be able to cope with this already.
Fixes: 5b73151fff ("powerpc: NMI IPI make NMI IPIs fully sychronous")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The NMI IPI timeout logic is broken, if __smp_send_nmi_ipi() times out
on the first condition, delay_us will be zero which will send it into
the second spin loop with no timeout so it will spin forever.
Fixes: 5b73151fff ("powerpc: NMI IPI make NMI IPIs fully sychronous")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We weren't using SYSCALL_DEFINE for sys_switch_endian(), which means
it wasn't able to be traced by CONFIG_FTRACE_SYSCALLS.
By using the macro we create the right metadata and the syscall is
visible. eg:
# cd /sys/kernel/debug/tracing
# echo 1 | tee events/syscalls/sys_*_switch_endian/enable
# ~/switch_endian_test
# cat trace
...
switch_endian_t-3604 [009] .... 315.175164: sys_switch_endian()
switch_endian_t-3604 [009] .... 315.175167: sys_switch_endian -> 0x5555aaaa5555aaaa
switch_endian_t-3604 [009] .... 315.175169: sys_switch_endian()
switch_endian_t-3604 [009] .... 315.175169: sys_switch_endian -> 0x5555aaaa5555aaaa
Fixes: 529d235a0e ("powerpc: Add a proper syscall for switching endianness")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 8792468da5 "powerpc: Add the ability to save FPU without
giving it up" unexpectedly removed the MSR_FE0 and MSR_FE1 bits from
the bitmask used to update the MSR of the previous thread in
__giveup_fpu() causing a KVM-PR MacOS guest to lockup and panic the
host kernel.
Leaving FE0/1 enabled means unrelated processes might receive FPEs
when they're not expecting them and crash. In particular if this
happens to init the host will then panic.
eg (transcribed):
qemu-system-ppc[837]: unhandled signal 8 at 12cc9ce4 nip 12cc9ce4 lr 12cc9ca4 code 0
systemd[1]: unhandled signal 8 at 202f02e0 nip 202f02e0 lr 001003d4 code 0
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Reinstate these bits to the MSR bitmask to enable MacOS guests to run
under 32-bit KVM-PR once again without issue.
Fixes: 8792468da5 ("powerpc: Add the ability to save FPU without giving it up")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds a debugfs interface to force scheduling a recovery event.
This can be used to recover a specific PE or schedule a "special" recovery
even that checks for errors at the PHB level.
To force a recovery of a normal PE, use:
echo '<#pe>:<#phb>' > /sys/kernel/debug/powerpc/eeh_force_recover
To force a scan for broken PHBs:
echo 'hwcheck' > /sys/kernel/debug/powerpc/eeh_force_recover
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently when we detect an error we automatically invoke the EEH recovery
handler. This can be annoying when debugging EEH problems, or when working
on EEH itself so this patch adds a debugfs knob that will prevent a
recovery event from being queued up when an issue is detected.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a helper to find the pci_controller structure based on the domain
number / phb id.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To use this function at all #define DEBUG needs to be set in eeh_cache.c.
Considering that printing at pr_debug is probably not all that useful since
it adds the additional hurdle of requiring you to enable the debug print if
dynamic_debug is in use so this patch bumps it to pr_info.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Adds a debugfs file that can be read to view the contents of the EEH
address cache. This is pretty similar to the existing
eeh_addr_cache_print() function, but that function is intended to debug
issues inside of the kernel since it's #ifdef`ed out by default, and writes
into the kernel log.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The EEH address cache is used to map a physical MMIO address back to a PCI
device. It's useful to know when it's being manipulated, but currently this
requires recompiling with #define DEBUG set. This is pointless since we
have dynamic_debug nowdays, so remove the #ifdef guard and add a pr_debug()
for the remove case too.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's no need to the custom getter/setter functions so we should remove
them in favour of using the generic one. While we're here, change the type
of eeh_max_freeze to u32 and print the value in decimal rather than
hex because printing it in hex makes no sense.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
GCC 8 warns about the logic in vr_get/set(), which with -Werror breaks
the build:
In function ‘user_regset_copyin’,
inlined from ‘vr_set’ at arch/powerpc/kernel/ptrace.c:628:9:
include/linux/regset.h:295:4: error: ‘memcpy’ offset [-527, -529] is
out of the bounds [0, 16] of object ‘vrsave’ with type ‘union
<anonymous>’ [-Werror=array-bounds]
arch/powerpc/kernel/ptrace.c: In function ‘vr_set’:
arch/powerpc/kernel/ptrace.c:623:5: note: ‘vrsave’ declared here
} vrsave;
This has been identified as a regression in GCC, see GCC bug 88273.
However we can avoid the warning and also simplify the logic and make
it more robust.
Currently we pass -1 as end_pos to user_regset_copyout(). This says
"copy up to the end of the regset".
The definition of the regset is:
[REGSET_VMX] = {
.core_note_type = NT_PPC_VMX, .n = 34,
.size = sizeof(vector128), .align = sizeof(vector128),
.active = vr_active, .get = vr_get, .set = vr_set
},
The end is calculated as (n * size), ie. 34 * sizeof(vector128).
In vr_get/set() we pass start_pos as 33 * sizeof(vector128), meaning
we can copy up to sizeof(vector128) into/out-of vrsave.
The on-stack vrsave is defined as:
union {
elf_vrreg_t reg;
u32 word;
} vrsave;
And elf_vrreg_t is:
typedef __vector128 elf_vrreg_t;
So there is no bug, but we rely on all those sizes lining up,
otherwise we would have a kernel stack exposure/overwrite on our
hands.
Rather than relying on that we can pass an explict end_pos based on
the sizeof(vrsave). The result should be exactly the same but it's
more obviously not over-reading/writing the stack and it avoids the
compiler warning.
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Mathieu Malaterre <malat@debian.org>
Cc: stable@vger.kernel.org
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds an "in_guest" parameter to machine_check_print_event_info()
so that we can avoid trying to translate guest NIP values into
symbolic form using the host kernel's symbol table.
Reviewed-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no good reason for this helper, just opencode it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we've switched all the powerpc nommu and swiotlb methods to
use the generic dma_direct_* calls we can remove these ops vectors
entirely and rely on the common direct mapping bypass that avoids
indirect function calls entirely. This also allows to remove a whole
lot of boilerplate code related to setting up these operations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Switch the streaming DMA mapping and ownership transfer methods to the
functionally identical dma_direct_ versions. Factor the cache
maintainance helpers into the form expected by the common code for that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The generic code allows a few nice things such as node local allocations
and dipping into the CMA area. The lookup of the right zone for a given
dma mask works a little different, but the results should be the same.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The only user left is powerpc, but even there the generic dma-direct
version works just as well, given that we guarantee that the swiotlb
buffer must always be addressable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This function is largely identical to the generic version used
everywhere else. Replace it with the generic version.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This function is identical to the generic dma_direct_get_required_mask,
except that the generic version also takes the bus_dma_mask account,
which could lead to incorrect results in the powerpc version.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The coherent cache version of this function already is functionally
identicall to the default version, and by defining the
arch_dma_coherent_to_pfn hook the same is ture for the noncoherent
version as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the standard portable helper instead of the powerpc specific one,
which is about to go away.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of letting the architecture supply all of dma_set_mask just
give it an additional hook selected by Kconfig.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The max_direct_dma_addr duplicates the bus_dma_mask field in struct
device. Use the generic field instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pci_dma_dev_setup_swiotlb is only used by the fsl_pci code, and closely
related to it, so fsl_pci.c seems like a better place for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This function is only used by the Cell iommu code, which can keep track
if it is using the iommu internally just as good.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All iommu capable platforms now always use the iommu code with the
internal bypass, so there is not need for this magic anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ppc_md and pci_controller_ops methods are unused now and can be
removed. The dma_nommu implementation is generic to the generic one
except for using max_pfn instead of calling into the memblock API,
and all other dma_map_ops instances implement a method of their own.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This gets rid of a lot of clumsy code and finally allows us to mark
dma_iommu_ops const.
Includes fixes from Michael Ellerman.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a new iommu_bypass flag to struct dev_archdata so that the dma_iommu
implementation can handle the direct mapping transparently instead of
switiching ops around. Setting of this flag is controlled by new
pci_controller_ops method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
vio_dma_mapping_ops currently does a lot of indirect calls through
dma_iommu_ops, which not only make the code harder to follow but are
also expensive in the post-spectre world. Unwind the indirect calls
by calling the ppc_iommu_* or iommu_* APIs directly applicable, or
just use the dma_iommu_* methods directly where we can.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This series finally gets us to the point of having system calls with
64-bit time_t on all architectures, after a long time of incremental
preparation patches.
There was actually one conversion that I missed during the summer,
i.e. Deepa's timex series, which I now updated based the 5.0-rc1 changes
and review comments.
The following system calls are now added on all 32-bit architectures
using the same system call numbers:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
Each one of these corresponds directly to an existing system call
that includes a 'struct timespec' argument, or a structure containing
a timespec or (in case of clock_adjtime) timeval. Not included here
are new versions of getitimer/setitimer and getrusage/waitid, which
are planned for the future but only needed to make a consistent API
rather than for correct operation beyond y2038. These four system
calls are based on 'timeval', and it has not been finally decided
what the replacement kernel interface will use instead.
So far, I have done a lot of build testing across most architectures,
which has found a number of bugs. Runtime testing so far included
testing LTP on 32-bit ARM with the existing system calls, to ensure
we do not regress for existing binaries, and a test with a 32-bit
x86 build of LTP against a modified version of the musl C library
that has been adapted to the new system call interface [3].
This library can be used for testing on all architectures supported
by musl-1.1.21, but it is not how the support is getting integrated
into the official musl release. Official musl support is planned
but will require more invasive changes to the library.
Link: https://lore.kernel.org/lkml/20190110162435.309262-1-arnd@arndb.de/T/
Link: https://lore.kernel.org/lkml/20190118161835.2259170-1-arnd@arndb.de/
Link: https://git.linaro.org/people/arnd/musl-y2038.git/ [2]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IZVb
-----END PGP SIGNATURE-----
Merge tag 'y2038-new-syscalls' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull y2038 - time64 system calls from Arnd Bergmann:
This series finally gets us to the point of having system calls with 64-bit
time_t on all architectures, after a long time of incremental preparation
patches.
There was actually one conversion that I missed during the summer,
i.e. Deepa's timex series, which I now updated based the 5.0-rc1 changes
and review comments.
The following system calls are now added on all 32-bit architectures using
the same system call numbers:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
Each one of these corresponds directly to an existing system call that
includes a 'struct timespec' argument, or a structure containing a timespec
or (in case of clock_adjtime) timeval. Not included here are new versions
of getitimer/setitimer and getrusage/waitid, which are planned for the
future but only needed to make a consistent API rather than for correct
operation beyond y2038. These four system calls are based on 'timeval', and
it has not been finally decided what the replacement kernel interface will
use instead.
So far, I have done a lot of build testing across most architectures, which
has found a number of bugs. Runtime testing so far included testing LTP on
32-bit ARM with the existing system calls, to ensure we do not regress for
existing binaries, and a test with a 32-bit x86 build of LTP against a
modified version of the musl C library that has been adapted to the new
system call interface [3]. This library can be used for testing on all
architectures supported by musl-1.1.21, but it is not how the support is
getting integrated into the official musl release. Official musl support is
planned but will require more invasive changes to the library.
Link: https://lore.kernel.org/lkml/20190110162435.309262-1-arnd@arndb.de/T/
Link: https://lore.kernel.org/lkml/20190118161835.2259170-1-arnd@arndb.de/
Link: https://git.linaro.org/people/arnd/musl-y2038.git/ [2]
The system call tables have diverged a bit over the years, and a number
of the recent additions never made it into all architectures, for one
reason or another.
This is an attempt to clean it up as far as we can without breaking
compatibility, doing a number of steps:
- Add system calls that have not yet been integrated into all
architectures but that we definitely want there. This includes
{,f}statfs64() and get{eg,eu,g,p,u,pp}id() on alpha, which have
been missing traditionally.
- The s390 compat syscall handling is cleaned up to be more like
what we do on other architectures, while keeping the 31-bit
pointer extension. This was merged as a shared branch by the
s390 maintainers and is included here in order to base the other
patches on top.
- Add the separate ipc syscalls on all architectures that
traditionally only had sys_ipc(). This version is done without
support for IPC_OLD that is we have in sys_ipc. The
new semtimedop_time64 syscall will only be added here, not
in sys_ipc
- Add syscall numbers for a couple of syscalls that we probably
don't need everywhere, in particular pkey_* and rseq,
for the purpose of symmetry: if it's in asm-generic/unistd.h,
it makes sense to have it everywhere. I expect that any future
system calls will get assigned on all platforms together, even
when they appear to be specific to a single architecture.
- Prepare for having the same system call numbers for any future
calls. In combination with the generated tables, this hopefully
makes it easier to add new calls across all architectures
together.
All of the above are technically separate from the y2038 work,
but are done as preparation before we add the new 64-bit time_t
system calls everywhere, providing a common baseline set of system
calls.
I expect that glibc and other libraries that want to use 64-bit
time_t will require linux-5.1 kernel headers for building in
the future, and at a much later point may also require linux-5.1
or a later version as the minimum kernel at runtime. Having a
common baseline then allows the removal of many architecture or
kernel version specific workarounds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=s4wf
-----END PGP SIGNATURE-----
Merge tag 'y2038-syscall-cleanup' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull preparatory work for y2038 changes from Arnd Bergmann:
System call unification and cleanup
The system call tables have diverged a bit over the years, and a number of
the recent additions never made it into all architectures, for one reason
or another.
This is an attempt to clean it up as far as we can without breaking
compatibility, doing a number of steps:
- Add system calls that have not yet been integrated into all architectures
but that we definitely want there. This includes {,f}statfs64() and
get{eg,eu,g,p,u,pp}id() on alpha, which have been missing traditionally.
- The s390 compat syscall handling is cleaned up to be more like what we
do on other architectures, while keeping the 31-bit pointer
extension. This was merged as a shared branch by the s390 maintainers
and is included here in order to base the other patches on top.
- Add the separate ipc syscalls on all architectures that traditionally
only had sys_ipc(). This version is done without support for IPC_OLD
that is we have in sys_ipc. The new semtimedop_time64 syscall will only
be added here, not in sys_ipc
- Add syscall numbers for a couple of syscalls that we probably don't need
everywhere, in particular pkey_* and rseq, for the purpose of symmetry:
if it's in asm-generic/unistd.h, it makes sense to have it everywhere. I
expect that any future system calls will get assigned on all platforms
together, even when they appear to be specific to a single architecture.
- Prepare for having the same system call numbers for any future calls. In
combination with the generated tables, this hopefully makes it easier to
add new calls across all architectures together.
All of the above are technically separate from the y2038 work, but are done
as preparation before we add the new 64-bit time_t system calls everywhere,
providing a common baseline set of system calls.
I expect that glibc and other libraries that want to use 64-bit time_t will
require linux-5.1 kernel headers for building in the future, and at a much
later point may also require linux-5.1 or a later version as the minimum
kernel at runtime. Having a common baseline then allows the removal of many
architecture or kernel version specific workarounds.
This adds 21 new system calls on each ABI that has 32-bit time_t
today. All of these have the exact same semantics as their existing
counterparts, and the new ones all have macro names that end in 'time64'
for clarification.
This gets us to the point of being able to safely use a C library
that has 64-bit time_t in user space. There are still a couple of
loose ends to tie up in various areas of the code, but this is the
big one, and should be entirely uncontroversial at this point.
In particular, there are four system calls (getitimer, setitimer,
waitid, and getrusage) that don't have a 64-bit counterpart yet,
but these can all be safely implemented in the C library by wrapping
around the existing system calls because the 32-bit time_t they
pass only counts elapsed time, not time since the epoch. They
will be dealt with later.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
The time, stime, utime, utimes, and futimesat system calls are only
used on older architectures, and we do not provide y2038 safe variants
of them, as they are replaced by clock_gettime64, clock_settime64,
and utimensat_time64.
However, for consistency it seems better to have the 32-bit architectures
that still use them call the "time32" entry points (leaving the
traditional handlers for the 64-bit architectures), like we do for system
calls that now require two versions.
Note: We used to always define __ARCH_WANT_SYS_TIME and
__ARCH_WANT_SYS_UTIME and only set __ARCH_WANT_COMPAT_SYS_TIME and
__ARCH_WANT_SYS_UTIME32 for compat mode on 64-bit kernels. Now this is
reversed: only 64-bit architectures set __ARCH_WANT_SYS_TIME/UTIME, while
we need __ARCH_WANT_SYS_TIME32/UTIME32 for 32-bit architectures and compat
mode. The resulting asm/unistd.h changes look a bit counterintuitive.
This is only a cleanup patch and it should not change any behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This is the big flip, where all 32-bit architectures set COMPAT_32BIT_TIME
and use the _time32 system calls from the former compat layer instead
of the system calls that take __kernel_timespec and similar arguments.
The temporary redirects for __kernel_timespec, __kernel_itimerspec
and __kernel_timex can get removed with this.
It would be easy to split this commit by architecture, but with the new
generated system call tables, it's easy enough to do it all at once,
which makes it a little easier to check that the changes are the same
in each table.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of system calls that pass a time_t somewhere have an implementation
using a COMPAT_SYSCALL_DEFINEx() on 64-bit architectures, and have
been reworked so that this implementation can now be used on 32-bit
architectures as well.
The missing step is to redefine them using the regular SYSCALL_DEFINEx()
to get them out of the compat namespace and make it possible to build them
on 32-bit architectures.
Any system call that ends in 'time' gets a '32' suffix on its name for
that version, while the others get a '_time32' suffix, to distinguish
them from the normal version, which takes a 64-bit time argument in the
future.
In this step, only 64-bit architectures are changed, doing this rename
first lets us avoid touching the 32-bit architectures twice.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
'regno' is directly controlled by user space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
On PTRACE_SETREGS and PTRACE_GETREGS requests, user space passes the
register number that would be read or written. This register number is
called 'regno' which is part of the 'addr' syscall parameter.
This 'regno' value is checked against the maximum pt_regs structure size,
and then used to dereference it, which matches the initial part of a
Spectre v1 (and Spectre v1.1) attack. The dereferenced value, then,
is returned to userspace in the GETREGS case.
This patch sanitizes 'regno' before using it to dereference pt_reg.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When building a 32 bit powerpc kernel with Binutils 2.31.1 this warning
is emitted:
powerpc-linux-gnu-ld: warning: orphan section `.branch_lt' from
`arch/powerpc/kernel/head_44x.o' being placed in section `.branch_lt'
As of binutils commit 2d7ad24e8726 ("Support PLT16 relocs against local
symbols")[1], 32 bit targets can produce .branch_lt sections in their
output.
Include these symbols in the .data section as the ppc64 kernel does.
[1] https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commitdiff;h=2d7ad24e8726ba4c45c9e67be08223a146a837ce
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, eeh_pe_reset_full() will only attempt to reset a PE more
than once if activating the reset state and deactivating it both
succeed, but later polling shows that it hasn't become active.
Change this so that it will try up to three times for any reason other
than an unrecoverable slot error and adjust the message generation so
that it's clear weather the reset has ultimately succeeded or failed.
This allows the reset to succeed in some situations where it would
currently fail.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, the EEH recovery process considers passed-through devices
as if they were not EEH-aware, which can cause them to be removed as
part of recovery. Because device removal requires cooperation from
the guest, this may lead to the process stalling or deadlocking.
Also, if devices are removed on the host side, they will be removed
from their IOMMU group, making recovery in the guest impossible.
Therefore, alter the recovery process so that passed-through devices
are not removed but are instead left frozen (and marked isolated)
until the guest performs it's own recovery. If firmware thaws a
passed-through PE because it's parent PE has been thawed (because it
was not passed through), re-freeze it.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a parameter to eeh_clear_pe_frozen_state() that allows
passed-through PEs to be excluded. Update callers to always pass true
so that there is no change in behaviour.
This is to prepare for follow-up work for passed-through devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a parameter to eeh_pe_state_clear() that allows passed-through PEs
to be excluded. Update callers to always pass true so that there is no
change in behaviour.
Also refactor to use direct traversal, to allow the removal of some
boilerplate.
This is to prepare for follow-up work for passed-through devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_unfreeze_pe() performs two operations: unfreezing a PE (which may
cause firmware to unfreeze child PEs as well) and de-isolating the PE
and it's children.
To simplify this and support future work, separate out the
de-isolation and perform it at the call sites (when necessary).
There should be no change in behaviour.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 'clear_sw_state' parameter for eeh_pe_clear_frozen_state() is
redundant because it has no effect (except in the rare case of a
hardware error part way through unfreezing a tree of PEs, where it
would dangerously allow partial de-isolation before returning
failure).
It is passed down to __eeh_pe_clear_frozen_state(), and from there to
eeh_unfreeze_pe(), where it causes EEH_PE_ISOLATED to be removed
from the state of each PE during the traversal. However, when the
traversal finishes, EEH_PE_ISOLATED is unconditionally removed by a
call to eeh_pe_state_clear() regardless of the parameter's value.
So remove the flag and pass false to eeh_unfreeze_pe() (to avoid the
rare case described above, as it was before the flag was introduced).
Also, perform the recursion directly in the function and eliminate a
bit of boilerplate.
There should be no change in functionality, except as mentioned above.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To match its x86 counterpart, save_stack_trace_tsk_reliable() should
return -EINVAL in cases that it is currently returning 1. No caller is
currently differentiating non-zero error codes, but let's keep the
arch-specific implementations consistent.
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mostly cosmetic changes:
- Group common stack pointer code at the top
- Simplify the first frame logic
- Code stackframe iteration into for...loop construct
- Check for trace->nr_entries overflow before adding any into the array
Suggested-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The bottom-most stack frame (the first to be unwound) may be largely
uninitialized, for the "Power Architecture 64-Bit ELF V2 ABI" only
requires its backchain pointer to be set.
The reliable stack tracer should be careful when verifying this frame:
skip checks on STACK_FRAME_LR_SAVE and STACK_FRAME_MARKER offsets that
may contain uninitialized residual data.
Fixes: df78d3f614 ("powerpc/livepatch: Implement reliable stack tracing for the consistency model")
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ppc64 specific implementation of the reliable stacktracer,
save_stack_trace_tsk_reliable(), bails out and reports an "unreliable
trace" whenever it finds an exception frame on the stack. Stack frames
are classified as exception frames if the STACK_FRAME_REGS_MARKER
magic, as written by exception prologues, is found at a particular
location.
However, as observed by Joe Lawrence, it is possible in practice that
non-exception stack frames can alias with prior exception frames and
thus, that the reliable stacktracer can find a stale
STACK_FRAME_REGS_MARKER on the stack. It in turn falsely reports an
unreliable stacktrace and blocks any live patching transition to
finish. Said condition lasts until the stack frame is
overwritten/initialized by function call or other means.
In principle, we could mitigate this by making the exception frame
classification condition in save_stack_trace_tsk_reliable() stronger:
in addition to testing for STACK_FRAME_REGS_MARKER, we could also take
into account that for all exceptions executing on the kernel stack
- their stack frames's backlink pointers always match what is saved
in their pt_regs instance's ->gpr[1] slot and that
- their exception frame size equals STACK_INT_FRAME_SIZE, a value
uncommonly large for non-exception frames.
However, while these are currently true, relying on them would make
the reliable stacktrace implementation more sensitive towards future
changes in the exception entry code. Note that false negatives, i.e.
not detecting exception frames, would silently break the live patching
consistency model.
Furthermore, certain other places (diagnostic stacktraces, perf, xmon)
rely on STACK_FRAME_REGS_MARKER as well.
Make the exception exit code clear the on-stack
STACK_FRAME_REGS_MARKER for those exceptions running on the "normal"
kernel stack and returning to kernelspace: because the topmost frame
is ignored by the reliable stack tracer anyway, returns to userspace
don't need to take care of clearing the marker.
Furthermore, as I don't have the ability to test this on Book 3E or 32
bits, limit the change to Book 3S and 64 bits.
Fixes: df78d3f614 ("powerpc/livepatch: Implement reliable stack tracing for the consistency model")
Reported-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove linux/rtc.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The IPC system call handling is highly inconsistent across architectures,
some use sys_ipc, some use separate calls, and some use both. We also
have some architectures that require passing IPC_64 in the flags, and
others that set it implicitly.
For the addition of a y2038 safe semtimedop() system call, I chose to only
support the separate entry points, but that requires first supporting
the regular ones with their own syscall numbers.
The IPC_64 is now implied by the new semctl/shmctl/msgctl system
calls even on the architectures that require passing it with the ipc()
multiplexer.
I'm not adding the new semtimedop() or semop() on 32-bit architectures,
those will get implemented using the new semtimedop_time64() version
that gets added along with the other time64 calls.
Three 64-bit architectures (powerpc, s390 and sparc) get semtimedop().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Adopt nvram module to reduce code duplication. This means CONFIG_NVRAM
becomes available to PPC64 builds. Previously it was only available to
PPC32 builds because it depended on CONFIG_GENERIC_NVRAM.
The IOC_NVRAM_GET_OFFSET ioctl as implemented on PPC64 validates the
offset returned by pmac_get_partition(). Do the same in the nvram module.
Note that the old PPC32 generic_nvram module lacked this test.
So when CONFIG_PPC32 && CONFIG_PPC_PMAC, the IOC_NVRAM_GET_OFFSET ioctl
would have returned 0 (always). But when CONFIG_PPC64 && CONFIG_PPC_PMAC,
the IOC_NVRAM_GET_OFFSET ioctl would have returned -1 (which is -EPERM)
when the requested partition was not found.
With this patch, the result is now -EINVAL on both PPC32 and PPC64 when
the requested PowerMac NVRAM partition is not found. This is a userspace-
visible change, in the non-existent partition case, which would be in
an error path for an IOC_NVRAM_GET_OFFSET ioctl syscall.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch PPC32 kernels from the generic_nvram module to the nvram module.
Also fix a theoretical bug where CHRP omits the chrp_nvram_init() call
when CONFIG_NVRAM_MODULE=m.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the nvram_read_byte() and nvram_write_byte() declarations in
powerpc/include/asm/nvram.h and use the cross-platform static functions
in linux/nvram.h instead.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently in commit fbf508da74 ("powerpc: split compat syscall table
out from native table") we changed the layout of the system call
table. Instead of having two entries for each syscall number, one for
the regular entry point and one for the compat entry point, we now
have separate tables for regular and compat entry points.
This inadvertently broke syscall tracing (CONFIG_FTRACE_SYSCALLS),
because our implementation of arch_syscall_addr() knew about the
layout of the table (it did nr * 2).
We can fix it just by dropping our version of arch_syscall_addr() and
using the generic version which does:
return (unsigned long)sys_call_table[nr];
Fixes: fbf508da74 ("powerpc: split compat syscall table out from native table")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On Power9 machines (64-bit Book3S), we can be running with either the
Hash table or Radix tree MMU enabled. So add some text to the __die()
output to tell us which is enabled, for the case where all you have is
the oops output and no other information.
Example output:
kernel BUG at drivers/misc/lkdtm/bugs.c:63!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: kvm vmx_crypto binfmt_misc ip_tables x_tables
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The page size the kernel is built with is useful info when debugging a
crash, so add it to the output in __die().
Result looks like eg:
kernel BUG at drivers/misc/lkdtm/bugs.c:63!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: vmx_crypto kvm binfmt_misc ip_tables
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Using pr_cont() risks having our output interleaved with other output
from other CPUs. Instead print everything in a single printk() call.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the ld documentation under Builtin Functions:
BLOCK(exp)
This is a synonym for ALIGN, for compatibility with older linker scripts.
Clang's linker (lld) doesn't know about BLOCK so remove this use of
it.
Suggested-by: George Rimar <grimar@accesssoftek.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch_early_irq_init() does nothing different than the weak
arch_early_irq_init() in kernel/softirq.c
Fixes: 089fb442f3 ("powerpc: Use ARCH_IRQ_INIT_FLAGS")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use a CONSOLE_LOGLEVEL_DEBUG macro for console_loglevel rather
than a naked number.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit e1c3743e1a ("powerpc/tm: Set MSR[TS] just prior to recheckpoint")
moved a code block around and this block uses a 'msr' variable outside of
the CONFIG_PPC_TRANSACTIONAL_MEM, however the 'msr' variable is declared
inside a CONFIG_PPC_TRANSACTIONAL_MEM block, causing a possible error when
CONFIG_PPC_TRANSACTION_MEM is not defined.
error: 'msr' undeclared (first use in this function)
This is not causing a compilation error in the mainline kernel, because
'msr' is being used as an argument of MSR_TM_ACTIVE(), which is defined as
the following when CONFIG_PPC_TRANSACTIONAL_MEM is *not* set:
#define MSR_TM_ACTIVE(x) 0
This patch just fixes this issue avoiding the 'msr' variable usage outside
the CONFIG_PPC_TRANSACTIONAL_MEM block, avoiding trusting in the
MSR_TM_ACTIVE() definition.
Cc: stable@vger.kernel.org
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Fixes: e1c3743e1a ("powerpc/tm: Set MSR[TS] just prior to recheckpoint")
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 8c8c10b90d ("powerpc/8xx: fix handling of early NULL pointer
dereference") moved the loading of r6 earlier in the code. As some
functions are called inbetween, r6 needs to be loaded again with the
address of swapper_pg_dir in order to set PTE pointers for
the Abatron BDI.
Fixes: 8c8c10b90d ("powerpc/8xx: fix handling of early NULL pointer dereference")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".
The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:
#if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
# define HAVE_JUMP_LABEL
#endif
We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.
Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Including (in no particular order):
- Page table code for AMD IOMMU now supports large pages where
smaller page-sizes were mapped before. VFIO had to work around
that in the past and I included a patch to remove it (acked by
Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would
never work as modules anyway.
- Work to unify the the iommu-related pointers in
'struct device' into one pointer. This work is not finished
yet, but will probably be in the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DT9A
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
Mostly clean ups although whilst Doug's was chasing down a odd
lockdep warning he also did some work to improved debugger resilience
when some CPUs fail to respond to the round up request.
The main changes are:
* Fixing a lockdep warning on architectures that cannot use an NMI for
the round up plus related changes to make CPU round up and all CPU
backtrace more resilient.
* Constify the arch ops tables
* A couple of other small clean ups
Two of the three patchsets here include changes that spill over into
arch/. Changes in the arch space are relatively narrow in scope
(and directly related to kgdb). Didn't get comprehensive acks but
all impacted maintainers were Cc:ed in good time.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=Aqlc
-----END PGP SIGNATURE-----
Merge tag 'kgdb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"Mostly clean ups although while Doug's was chasing down a odd lockdep
warning he also did some work to improved debugger resilience when
some CPUs fail to respond to the round up request.
The main changes are:
- Fixing a lockdep warning on architectures that cannot use an NMI
for the round up plus related changes to make CPU round up and all
CPU backtrace more resilient.
- Constify the arch ops tables
- A couple of other small clean ups
Two of the three patchsets here include changes that spill over into
arch/. Changes in the arch space are relatively narrow in scope (and
directly related to kgdb). Didn't get comprehensive acks but all
impacted maintainers were Cc:ed in good time"
* tag 'kgdb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
kgdb/treewide: constify struct kgdb_arch arch_kgdb_ops
mips/kgdb: prepare arch_kgdb_ops for constness
kdb: use bool for binary state indicators
kdb: Don't back trace on a cpu that didn't round up
kgdb: Don't round up a CPU that failed rounding up before
kgdb: Fix kgdb_roundup_cpus() for arches who used smp_call_function()
kgdb: Remove irq flags from roundup
- Rework of the kprobe/uprobe and synthetic events to consolidate all
the dynamic event code. This will make changes in the future easier.
- Partial rewrite of the function graph tracing infrastructure.
This will allow for multiple users of hooking onto functions
to get the callback (return) of the function. This is the ground
work for having kprobes and function graph tracer using one code base.
- Clean up of the histogram code that will facilitate adding more
features to the histograms in the future.
- Addition of str_has_prefix() and a few use cases. There currently
is a similar function strstart() that is used in a few places, but
only returns a bool and not a length. These instances will be
removed in the future to use str_has_prefix() instead.
- A few other various clean ups as well.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXCawlBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhbcAQCFeT0fWWTUxofBQz5jqsHaRnVg21+9
X4sTldYRYEn4YgEAmWOyiwq7zvrsAu4ZwkNBMeqxn3tVymYHiGOGe3Y4BAw=
=u96o
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Rework of the kprobe/uprobe and synthetic events to consolidate all
the dynamic event code. This will make changes in the future easier.
- Partial rewrite of the function graph tracing infrastructure. This
will allow for multiple users of hooking onto functions to get the
callback (return) of the function. This is the ground work for having
kprobes and function graph tracer using one code base.
- Clean up of the histogram code that will facilitate adding more
features to the histograms in the future.
- Addition of str_has_prefix() and a few use cases. There currently is
a similar function strstart() that is used in a few places, but only
returns a bool and not a length. These instances will be removed in
the future to use str_has_prefix() instead.
- A few other various clean ups as well.
* tag 'trace-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
tracing: Use the return of str_has_prefix() to remove open coded numbers
tracing: Have the historgram use the result of str_has_prefix() for len of prefix
tracing: Use str_has_prefix() instead of using fixed sizes
tracing: Use str_has_prefix() helper for histogram code
string.h: Add str_has_prefix() helper function
tracing: Make function ‘ftrace_exports’ static
tracing: Simplify printf'ing in seq_print_sym
tracing: Avoid -Wformat-nonliteral warning
tracing: Merge seq_print_sym_short() and seq_print_sym_offset()
tracing: Add hist trigger comments for variable-related fields
tracing: Remove hist trigger synth_var_refs
tracing: Use hist trigger's var_ref array to destroy var_refs
tracing: Remove open-coding of hist trigger var_ref management
tracing: Use var_refs[] for hist trigger reference checking
tracing: Change strlen to sizeof for hist trigger static strings
tracing: Remove unnecessary hist trigger struct field
tracing: Fix ftrace_graph_get_ret_stack() to use task and not current
seq_buf: Use size_t for len in seq_buf_puts()
seq_buf: Make seq_buf_puts() null-terminate the buffer
arm64: Use ftrace_graph_get_ret_stack() instead of curr_ret_stack
...
checkpatch.pl reports the following:
WARNING: struct kgdb_arch should normally be const
#28: FILE: arch/mips/kernel/kgdb.c:397:
+struct kgdb_arch arch_kgdb_ops = {
This report makes sense, as all other ops struct, this
one should also be const. This patch does the change.
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: x86@kernel.org
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
When I had lockdep turned on and dropped into kgdb I got a nice splat
on my system. Specifically it hit:
DEBUG_LOCKS_WARN_ON(current->hardirq_context)
Specifically it looked like this:
sysrq: SysRq : DEBUG
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(current->hardirq_context)
WARNING: CPU: 0 PID: 0 at .../kernel/locking/lockdep.c:2875 lockdep_hardirqs_on+0xf0/0x160
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.0 #27
pstate: 604003c9 (nZCv DAIF +PAN -UAO)
pc : lockdep_hardirqs_on+0xf0/0x160
...
Call trace:
lockdep_hardirqs_on+0xf0/0x160
trace_hardirqs_on+0x188/0x1ac
kgdb_roundup_cpus+0x14/0x3c
kgdb_cpu_enter+0x53c/0x5cc
kgdb_handle_exception+0x180/0x1d4
kgdb_compiled_brk_fn+0x30/0x3c
brk_handler+0x134/0x178
do_debug_exception+0xfc/0x178
el1_dbg+0x18/0x78
kgdb_breakpoint+0x34/0x58
sysrq_handle_dbg+0x54/0x5c
__handle_sysrq+0x114/0x21c
handle_sysrq+0x30/0x3c
qcom_geni_serial_isr+0x2dc/0x30c
...
...
irq event stamp: ...45
hardirqs last enabled at (...44): [...] __do_softirq+0xd8/0x4e4
hardirqs last disabled at (...45): [...] el1_irq+0x74/0x130
softirqs last enabled at (...42): [...] _local_bh_enable+0x2c/0x34
softirqs last disabled at (...43): [...] irq_exit+0xa8/0x100
---[ end trace adf21f830c46e638 ]---
Looking closely at it, it seems like a really bad idea to be calling
local_irq_enable() in kgdb_roundup_cpus(). If nothing else that seems
like it could violate spinlock semantics and cause a deadlock.
Instead, let's use a private csd alongside
smp_call_function_single_async() to round up the other CPUs. Using
smp_call_function_single_async() doesn't require interrupts to be
enabled so we can remove the offending bit of code.
In order to avoid duplicating this across all the architectures that
use the default kgdb_roundup_cpus(), we'll add a "weak" implementation
to debug_core.c.
Looking at all the people who previously had copies of this code,
there were a few variants. I've attempted to keep the variants
working like they used to. Specifically:
* For arch/arc we passed NULL to kgdb_nmicallback() instead of
get_irq_regs().
* For arch/mips there was a bit of extra code around
kgdb_nmicallback()
NOTE: In this patch we will still get into trouble if we try to round
up a CPU that failed to round up before. We'll try to round it up
again and potentially hang when we try to grab the csd lock. That's
not new behavior but we'll still try to do better in a future patch.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
The function kgdb_roundup_cpus() was passed a parameter that was
documented as:
> the flags that will be used when restoring the interrupts. There is
> local_irq_save() call before kgdb_roundup_cpus().
Nobody used those flags. Anyone who wanted to temporarily turn on
interrupts just did local_irq_enable() and local_irq_disable() without
looking at them. So we can definitely remove the flags.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Fixed the following build warning:
powerpc-linux-gnu-ld: warning: orphan section `__btb_flush_fixup' from
`arch/powerpc/kernel/head_44x.o' being placed in section
`__btb_flush_fixup'.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for architectures
that have devices that perform DMA that is not cache coherent. Based
on the existing arm64 implementation and also used for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel data
leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script.
-----BEGIN PGP SIGNATURE-----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=in72
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
"A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for
architectures that have devices that perform DMA that is not cache
coherent. Based on the existing arm64 implementation and also used
for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel
data leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script"
* tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping: (73 commits)
dma-mapping: fix inverted logic in dma_supported
dma-mapping: deprecate dma_zalloc_coherent
dma-mapping: zero memory returned from dma_alloc_*
sparc/iommu: fix ->map_sg return value
sparc/io-unit: fix ->map_sg return value
arm64: default to the direct mapping in get_arch_dma_ops
PCI: Remove unused attr variable in pci_dma_configure
ia64: only select ARCH_HAS_DMA_COHERENT_TO_PFN if swiotlb is enabled
dma-mapping: bypass indirect calls for dma-direct
vmd: use the proper dma_* APIs instead of direct methods calls
dma-direct: merge swiotlb_dma_ops into the dma_direct code
dma-direct: use dma_direct_map_page to implement dma_direct_map_sg
dma-direct: improve addressability error reporting
swiotlb: remove dma_mark_clean
swiotlb: remove SWIOTLB_MAP_ERROR
ACPI / scan: Refactor _CCA enforcement
dma-mapping: factor out dummy DMA ops
dma-mapping: always build the direct mapping code
dma-mapping: move dma_cache_sync out of line
dma-mapping: move various slow path functions out of line
...
Notable changes:
- Mitigations for Spectre v2 on some Freescale (NXP) CPUs.
- A large series adding support for pass-through of Nvidia V100 GPUs to guests
on Power9.
- Another large series to enable hardware assistance for TLB table walk on
MPC8xx CPUs.
- Some preparatory changes to our DMA code, to make way for further cleanups
from Christoph.
- Several fixes for our Transactional Memory handling discovered by fuzzing the
signal return path.
- Support for generating our system call table(s) from a text file like other
architectures.
- A fix to our page fault handler so that instead of generating a WARN_ON_ONCE,
user accesses of kernel addresses instead print a ratelimited and
appropriately scary warning.
- A cosmetic change to make our unhandled page fault messages more similar to
other arches and also more compact and informative.
- Freescale updates from Scott:
"Highlights include elimination of legacy clock bindings use from dts
files, an 83xx watchdog handler, fixes to old dts interrupt errors, and
some minor cleanup."
And many clean-ups, reworks and minor fixes etc.
Thanks to:
Alexandre Belloni, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Arnd Bergmann, Benjamin Herrenschmidt, Breno Leitao, Christian Lamparter,
Christophe Leroy, Christoph Hellwig, Daniel Axtens, Darren Stevens, David
Gibson, Diana Craciun, Dmitry V. Levin, Firoz Khan, Geert Uytterhoeven, Greg
Kurz, Gustavo Romero, Hari Bathini, Joel Stanley, Kees Cook, Madhavan
Srinivasan, Mahesh Salgaonkar, Markus Elfring, Mathieu Malaterre, Michal
Suchánek, Naveen N. Rao, Nick Desaulniers, Oliver O'Halloran, Paul Mackerras,
Ram Pai, Ravi Bangoria, Rob Herring, Russell Currey, Sabyasachi Gupta, Sam
Bobroff, Satheesh Rajendran, Scott Wood, Segher Boessenkool, Stephen Rothwell,
Tang Yuantian, Thiago Jung Bauermann, Yangtao Li, Yuantian Tang, Yue Haibing.
-----BEGIN PGP SIGNATURE-----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=cr6s
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Mitigations for Spectre v2 on some Freescale (NXP) CPUs.
- A large series adding support for pass-through of Nvidia V100 GPUs
to guests on Power9.
- Another large series to enable hardware assistance for TLB table
walk on MPC8xx CPUs.
- Some preparatory changes to our DMA code, to make way for further
cleanups from Christoph.
- Several fixes for our Transactional Memory handling discovered by
fuzzing the signal return path.
- Support for generating our system call table(s) from a text file
like other architectures.
- A fix to our page fault handler so that instead of generating a
WARN_ON_ONCE, user accesses of kernel addresses instead print a
ratelimited and appropriately scary warning.
- A cosmetic change to make our unhandled page fault messages more
similar to other arches and also more compact and informative.
- Freescale updates from Scott:
"Highlights include elimination of legacy clock bindings use from
dts files, an 83xx watchdog handler, fixes to old dts interrupt
errors, and some minor cleanup."
And many clean-ups, reworks and minor fixes etc.
Thanks to: Alexandre Belloni, Alexey Kardashevskiy, Andrew Donnellan,
Aneesh Kumar K.V, Arnd Bergmann, Benjamin Herrenschmidt, Breno Leitao,
Christian Lamparter, Christophe Leroy, Christoph Hellwig, Daniel
Axtens, Darren Stevens, David Gibson, Diana Craciun, Dmitry V. Levin,
Firoz Khan, Geert Uytterhoeven, Greg Kurz, Gustavo Romero, Hari
Bathini, Joel Stanley, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Michal Suchánek, Naveen
N. Rao, Nick Desaulniers, Oliver O'Halloran, Paul Mackerras, Ram Pai,
Ravi Bangoria, Rob Herring, Russell Currey, Sabyasachi Gupta, Sam
Bobroff, Satheesh Rajendran, Scott Wood, Segher Boessenkool, Stephen
Rothwell, Tang Yuantian, Thiago Jung Bauermann, Yangtao Li, Yuantian
Tang, Yue Haibing"
* tag 'powerpc-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (201 commits)
Revert "powerpc/fsl_pci: simplify fsl_pci_dma_set_mask"
powerpc/zImage: Also check for stdout-path
powerpc: Fix HMIs on big-endian with CONFIG_RELOCATABLE=y
macintosh: Use of_node_name_{eq, prefix} for node name comparisons
ide: Use of_node_name_eq for node name comparisons
powerpc: Use of_node_name_eq for node name comparisons
powerpc/pseries/pmem: Convert to %pOFn instead of device_node.name
powerpc/mm: Remove very old comment in hash-4k.h
powerpc/pseries: Fix node leak in update_lmb_associativity_index()
powerpc/configs/85xx: Enable CONFIG_DEBUG_KERNEL
powerpc/dts/fsl: Fix dtc-flagged interrupt errors
clk: qoriq: add more compatibles strings
powerpc/fsl: Use new clockgen binding
powerpc/83xx: handle machine check caused by watchdog timer
powerpc/fsl-rio: fix spelling mistake "reserverd" -> "reserved"
powerpc/fsl_pci: simplify fsl_pci_dma_set_mask
arch/powerpc/fsl_rmu: Use dma_zalloc_coherent
vfio_pci: Add NVIDIA GV100GL [Tesla V100 SXM2] subdriver
vfio_pci: Allow regions to add own capabilities
vfio_pci: Allow mapping extra regions
...
single-stepping fixes, improved tracing, various timer and vGIC
fixes
* x86: Processor Tracing virtualization, STIBP support, some correctness fixes,
refactorings and splitting of vmx.c, use the Hyper-V range TLB flush hypercall,
reduce order of vcpu struct, WBNOINVD support, do not use -ftrace for __noclone
functions, nested guest support for PAUSE filtering on AMD, more Hyper-V
enlightenments (direct mode for synthetic timers)
* PPC: nested VFIO
* s390: bugfixes only this time
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcH0vFAAoJEL/70l94x66Dw/wH/2FZp1YOM5OgiJzgqnXyDbyf
dNEfWo472MtNiLsuf+ZAfJojVIu9cv7wtBfXNzW+75XZDfh/J88geHWNSiZDm3Fe
aM4MOnGG0yF3hQrRQyEHe4IFhGFNERax8Ccv+OL44md9CjYrIrsGkRD08qwb+gNh
P8T/3wJEKwUcVHA/1VHEIM8MlirxNENc78p6JKd/C7zb0emjGavdIpWFUMr3SNfs
CemabhJUuwOYtwjRInyx1y34FzYwW3Ejuc9a9UoZ+COahUfkuxHE8u+EQS7vLVF6
2VGVu5SA0PqgmLlGhHthxLqVgQYo+dB22cRnsLtXlUChtVAq8q9uu5sKzvqEzuE=
=b4Jx
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- selftests improvements
- large PUD support for HugeTLB
- single-stepping fixes
- improved tracing
- various timer and vGIC fixes
x86:
- Processor Tracing virtualization
- STIBP support
- some correctness fixes
- refactorings and splitting of vmx.c
- use the Hyper-V range TLB flush hypercall
- reduce order of vcpu struct
- WBNOINVD support
- do not use -ftrace for __noclone functions
- nested guest support for PAUSE filtering on AMD
- more Hyper-V enlightenments (direct mode for synthetic timers)
PPC:
- nested VFIO
s390:
- bugfixes only this time"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (171 commits)
KVM: x86: Add CPUID support for new instruction WBNOINVD
kvm: selftests: ucall: fix exit mmio address guessing
Revert "compiler-gcc: disable -ftracer for __noclone functions"
KVM: VMX: Move VM-Enter + VM-Exit handling to non-inline sub-routines
KVM: VMX: Explicitly reference RCX as the vmx_vcpu pointer in asm blobs
KVM: x86: Use jmp to invoke kvm_spurious_fault() from .fixup
MAINTAINERS: Add arch/x86/kvm sub-directories to existing KVM/x86 entry
KVM/x86: Use SVM assembly instruction mnemonics instead of .byte streams
KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()
KVM/MMU: Flush tlb directly in kvm_set_pte_rmapp()
KVM/MMU: Move tlb flush in kvm_set_pte_rmapp() to kvm_mmu_notifier_change_pte()
KVM: Make kvm_set_spte_hva() return int
KVM: Replace old tlb flush function with new one to flush a specified range.
KVM/MMU: Add tlb flush with range helper function
KVM/VMX: Add hv tlb range flush support
x86/hyper-v: Add HvFlushGuestAddressList hypercall support
KVM: Add tlb_remote_flush_with_range callback in kvm_x86_ops
KVM: x86: Disable Intel PT when VMXON in L1 guest
KVM: x86: Set intercept for Intel PT MSRs read/write
KVM: x86: Implement Intel PT MSRs read/write emulation
...
In the end, we ended up with quite a lot more than I expected:
- Support for ARMv8.3 Pointer Authentication in userspace (CRIU and
kernel-side support to come later)
- Support for per-thread stack canaries, pending an update to GCC that
is currently undergoing review
- Support for kexec_file_load(), which permits secure boot of a kexec
payload but also happens to improve the performance of kexec
dramatically because we can avoid the sucky purgatory code from
userspace. Kdump will come later (requires updates to libfdt).
- Optimisation of our dynamic CPU feature framework, so that all
detected features are enabled via a single stop_machine() invocation
- KPTI whitelisting of Cortex-A CPUs unaffected by Meltdown, so that
they can benefit from global TLB entries when KASLR is not in use
- 52-bit virtual addressing for userspace (kernel remains 48-bit)
- Patch in LSE atomics for per-cpu atomic operations
- Custom preempt.h implementation to avoid unconditional calls to
preempt_schedule() from preempt_enable()
- Support for the new 'SB' Speculation Barrier instruction
- Vectorised implementation of XOR checksumming and CRC32 optimisations
- Workaround for Cortex-A76 erratum #1165522
- Improved compatibility with Clang/LLD
- Support for TX2 system PMUS for profiling the L3 cache and DMC
- Reflect read-only permissions in the linear map by default
- Ensure MMIO reads are ordered with subsequent calls to Xdelay()
- Initial support for memory hotplug
- Tweak the threshold when we invalidate the TLB by-ASID, so that
mremap() performance is improved for ranges spanning multiple PMDs.
- Minor refactoring and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJcE4TmAAoJELescNyEwWM0Nr0H/iaU7/wQSzHyNXtZoImyKTul
Blu2ga4/EqUrTU7AVVfmkl/3NBILWlgQVpY6tH6EfXQuvnxqD7CizbHyLdyO+z0S
B5PsFUH2GLMNAi48AUNqGqkgb2knFbg+T+9IimijDBkKg1G/KhQnRg6bXX32mLJv
Une8oshUPBVJMsHN1AcQknzKariuoE3u0SgJ+eOZ9yA2ZwKxP4yy1SkDt3xQrtI0
lojeRjxcyjTP1oGRNZC+BWUtGOT35p7y6cGTnBd/4TlqBGz5wVAJUcdoxnZ6JYVR
O8+ob9zU+4I0+SKt80s7pTLqQiL9rxkKZ5joWK1pr1g9e0s5N5yoETXKFHgJYP8=
=sYdt
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 festive updates from Will Deacon:
"In the end, we ended up with quite a lot more than I expected:
- Support for ARMv8.3 Pointer Authentication in userspace (CRIU and
kernel-side support to come later)
- Support for per-thread stack canaries, pending an update to GCC
that is currently undergoing review
- Support for kexec_file_load(), which permits secure boot of a kexec
payload but also happens to improve the performance of kexec
dramatically because we can avoid the sucky purgatory code from
userspace. Kdump will come later (requires updates to libfdt).
- Optimisation of our dynamic CPU feature framework, so that all
detected features are enabled via a single stop_machine()
invocation
- KPTI whitelisting of Cortex-A CPUs unaffected by Meltdown, so that
they can benefit from global TLB entries when KASLR is not in use
- 52-bit virtual addressing for userspace (kernel remains 48-bit)
- Patch in LSE atomics for per-cpu atomic operations
- Custom preempt.h implementation to avoid unconditional calls to
preempt_schedule() from preempt_enable()
- Support for the new 'SB' Speculation Barrier instruction
- Vectorised implementation of XOR checksumming and CRC32
optimisations
- Workaround for Cortex-A76 erratum #1165522
- Improved compatibility with Clang/LLD
- Support for TX2 system PMUS for profiling the L3 cache and DMC
- Reflect read-only permissions in the linear map by default
- Ensure MMIO reads are ordered with subsequent calls to Xdelay()
- Initial support for memory hotplug
- Tweak the threshold when we invalidate the TLB by-ASID, so that
mremap() performance is improved for ranges spanning multiple PMDs.
- Minor refactoring and cleanups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (125 commits)
arm64: kaslr: print PHYS_OFFSET in dump_kernel_offset()
arm64: sysreg: Use _BITUL() when defining register bits
arm64: cpufeature: Rework ptr auth hwcaps using multi_entry_cap_matches
arm64: cpufeature: Reduce number of pointer auth CPU caps from 6 to 4
arm64: docs: document pointer authentication
arm64: ptr auth: Move per-thread keys from thread_info to thread_struct
arm64: enable pointer authentication
arm64: add prctl control for resetting ptrauth keys
arm64: perf: strip PAC when unwinding userspace
arm64: expose user PAC bit positions via ptrace
arm64: add basic pointer authentication support
arm64/cpufeature: detect pointer authentication
arm64: Don't trap host pointer auth use to EL2
arm64/kvm: hide ptrauth from guests
arm64/kvm: consistently handle host HCR_EL2 flags
arm64: add pointer authentication register bits
arm64: add comments about EC exception levels
arm64: perf: Treat EXCLUDE_EL* bit definitions as unsigned
arm64: kpti: Whitelist Cortex-A CPUs that don't implement the CSV3 field
arm64: enable per-task stack canaries
...
Freescale updates from Scott:
"Highlights include elimination of legacy clock bindings use from dts
files, an 83xx watchdog handler, fixes to old dts interrupt errors, and
some minor cleanup."
The structure of the ret_stack array on the task struct is going to
change, and accessing it directly via the curr_ret_stack index will no
longer give the ret_stack entry that holds the return address. To access
that, architectures must now use ftrace_graph_get_ret_stack() to get the
associated ret_stack that matches the saved return address.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
HMIs will crash the kernel due to
BRANCH_LINK_TO_FAR(hmi_exception_realmode)
Calling into the OPD instead of the actual code.
Fixes: 2337d20728 ("powerpc/64: CONFIG_RELOCATABLE support for hmi interrupts")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Use DOTSYM() rather than #ifdef]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
A couple of open coded iterating thru the child node names are converted
to use for_each_child_of_node() instead.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the watchdog timer is set in interrupt mode, it causes a
machine check when it times out. The purpose of this mode is to
ease debugging, not to crash the kernel and reboot the machine.
This patch implements a special handling for that, in order to not
crash the kernel if the watchdog times out while in interrupt or
within the idle task.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[scottwood: added missing #include]
Signed-off-by: Scott Wood <oss@buserror.net>
The powernv platform registers IOMMU groups and adds devices to them
from the pci_controller_ops::setup_bridge() hook except one case when
virtual functions (SRIOV VFs) are added from a bus notifier.
The pseries platform registers IOMMU groups from
the pci_controller_ops::dma_bus_setup() hook and adds devices from
the pci_controller_ops::dma_dev_setup() hook. The very same bus notifier
used for powernv does not add devices for pseries though as
__of_scan_bus() adds devices first, then it does the bus/dev DMA setup.
Both platforms use iommu_add_device() which takes a device and expects
it to have a valid IOMMU table struct with an iommu_table_group pointer
which in turn points the iommu_group struct (which represents
an IOMMU group). Although the helper seems easy to use, it relies on
some pre-existing device configuration and associated data structures
which it does not really need.
This simplifies iommu_add_device() to take the table_group pointer
directly. Pseries already has a table_group pointer handy and the bus
notified is not used anyway. For powernv, this copies the existing bus
notifier, makes it work for powernv only which means an easy way of
getting to the table_group pointer. This was tested on VFs but should
also support physical PCI hotplug.
Since iommu_add_device() receives the table_group pointer directly,
pseries does not do TCE cache invalidation (the hypervisor does) nor
allow multiple groups per a VFIO container (in other words sharing
an IOMMU table between partitionable endpoints), this removes
iommu_table_group_link from pseries.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This new memory does not have page structs as it is not plugged to
the host so gup() will fail anyway.
This adds 2 helpers:
- mm_iommu_newdev() to preregister the "memory device" memory so
the rest of API can still be used;
- mm_iommu_is_devmem() to know if the physical address is one of thise
new regions which we must avoid unpinning of.
This adds @mm to tce_page_is_contained() and iommu_tce_xchg() to test
if the memory is device memory to avoid pfn_to_page().
This adds a check for device memory in mm_iommu_ua_mark_dirty_rm() which
does delayed pages dirtying.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
System call table generation script must be run to gener-
ate unistd_32/64.h and syscall_table_32/64/c32/spu.h files.
This patch will have changes which will invokes the script.
This patch will generate unistd_32/64.h and syscall_table-
_32/64/c32/spu.h files by the syscall table generation
script invoked by parisc/Makefile and the generated files
against the removed files must be identical.
The generated uapi header file will be included in uapi/-
asm/unistd.h and generated system call table header file
will be included by kernel/systbl.S file.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The system call tables are in different format in all
architecture and it will be difficult to manually add or
modify the system calls in the respective files. To make
it easy by keeping a script and which will generate the
uapi header and syscall table file. This change will also
help to unify the implementation across all architectures.
The system call table generation script is added in
syscalls directory which contain the script to generate
both uapi header file and system call table files.
The syscall.tbl file will be the input for the scripts.
syscall.tbl contains the list of available system calls
along with system call number and corresponding entry point.
Add a new system call in this architecture will be possible
by adding new entry in the syscall.tbl file.
Adding a new table entry consisting of:
- System call number.
- ABI.
- System call name.
- Entry point name.
- Compat entry name, if required.
syscallhdr.sh and syscalltbl.sh will generate uapi header-
unistd_32/64.h and syscall_table_32/64/c32/spu.h files
respectively. File syscall_table_32/64/c32/spu.h is incl-
uded by syscall.S - the real system call table. Both *.sh
files will parse the content syscall.tbl to generate the
header and table files.
ARM, s390 and x86 architecuture does have similar support.
I leverage their implementation to come up with a generic
solution.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PowerPC uses a syscall table with native and compat calls
interleaved, which is a slightly simpler way to define two
matching tables.
As we move to having the tables generated, that advantage
is no longer important, but the interleaved table gets in
the way of using the same scripts as on the other archit-
ectures.
Split out a new compat_sys_call_table symbol that contains
all the compat calls, and leave the main table for the nat-
ive calls, to more closely match the method we use every-
where else.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the macro definition for compat_sys_sigsuspend from
asm/systbl.h to the file which it is getting included.
One of the patch in this patch series is generating uapi
header and syscall table files. In order to come up with
a common implimentation across all architecture, we need
to do this change.
This change will simplify the implementation of system
call table generation script and help to come up a common
implementation across all architecture.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a TM Bad Thing bug that can be caused when you return from a
signal context in a suspended transaction but with ucontext MSR[TS] unset.
This forces regs->msr[TS] to be set at syscall entrance (since the CPU
state is transactional). It also calls treclaim() to flush the transaction
state, which is done based on the live (mfmsr) MSR state.
Since user context MSR[TS] is not set, then restore_tm_sigcontexts() is not
called, thus, not executing recheckpoint, keeping the CPU state as not
transactional. When calling rfid, SRR1 will have MSR[TS] set, but the CPU
state is non transactional, causing the TM Bad Thing with the following
stack:
[ 33.862316] Bad kernel stack pointer 3fffd9dce3e0 at c00000000000c47c
cpu 0x8: Vector: 700 (Program Check) at [c00000003ff7fd40]
pc: c00000000000c47c: fast_exception_return+0xac/0xb4
lr: 00003fff865f442c
sp: 3fffd9dce3e0
msr: 8000000102a03031
current = 0xc00000041f68b700
paca = 0xc00000000fb84800 softe: 0 irq_happened: 0x01
pid = 1721, comm = tm-signal-sigre
Linux version 4.9.0-3-powerpc64le (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 SMP Debian 4.9.30-2+deb9u2 (2017-06-26)
WARNING: exception is not recoverable, can't continue
The same problem happens on 32-bits signal handler, and the fix is very
similar, if tm_recheckpoint() is not executed, then regs->msr[TS] should be
zeroed.
This patch also fixes a sparse warning related to lack of indentation when
CONFIG_PPC_TRANSACTIONAL_MEM is set.
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
CC: Stable <stable@vger.kernel.org> # 3.10+
Signed-off-by: Breno Leitao <leitao@debian.org>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Usually a TM Bad Thing exception is raised due to three different problems.
a) touching SPRs in an active transaction; b) using TM instruction with the
facility disabled and c) setting a wrong MSR/SRR1 at RFID.
The two initial cases are easy to identify by looking at the instructions.
The latter case is harder, because the MSR is masked after RFID, so, it is
very useful to look at the previous MSR (SRR1) before RFID as also the
current and masked MSR.
Since MSR is saved at paca just before RFID, this patch prints it if a TM
Bad thing happen, helping to understand what is the invalid TM transition
that is causing the exception.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As other exit points, move SRR1 (MSR) into paca->tm_scratch, so, if
there is a TM Bad Thing in RFID, it is easy to understand what was the
SRR1 value being used.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On a signal handler return, the user could set a context with MSR[TS] bits
set, and these bits would be copied to task regs->msr.
At restore_tm_sigcontexts(), after current task regs->msr[TS] bits are set,
several __get_user() are called and then a recheckpoint is executed.
This is a problem since a page fault (in kernel space) could happen when
calling __get_user(). If it happens, the process MSR[TS] bits were
already set, but recheckpoint was not executed, and SPRs are still invalid.
The page fault can cause the current process to be de-scheduled, with
MSR[TS] active and without tm_recheckpoint() being called. More
importantly, without TEXASR[FS] bit set also.
Since TEXASR might not have the FS bit set, and when the process is
scheduled back, it will try to reclaim, which will be aborted because of
the CPU is not in the suspended state, and, then, recheckpoint. This
recheckpoint will restore thread->texasr into TEXASR SPR, which might be
zero, hitting a BUG_ON().
kernel BUG at /build/linux-sf3Co9/linux-4.9.30/arch/powerpc/kernel/tm.S:434!
cpu 0xb: Vector: 700 (Program Check) at [c00000041f1576d0]
pc: c000000000054550: restore_gprs+0xb0/0x180
lr: 0000000000000000
sp: c00000041f157950
msr: 8000000100021033
current = 0xc00000041f143000
paca = 0xc00000000fb86300 softe: 0 irq_happened: 0x01
pid = 1021, comm = kworker/11:1
kernel BUG at /build/linux-sf3Co9/linux-4.9.30/arch/powerpc/kernel/tm.S:434!
Linux version 4.9.0-3-powerpc64le (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 SMP Debian 4.9.30-2+deb9u2 (2017-06-26)
enter ? for help
[c00000041f157b30] c00000000001bc3c tm_recheckpoint.part.11+0x6c/0xa0
[c00000041f157b70] c00000000001d184 __switch_to+0x1e4/0x4c0
[c00000041f157bd0] c00000000082eeb8 __schedule+0x2f8/0x990
[c00000041f157cb0] c00000000082f598 schedule+0x48/0xc0
[c00000041f157ce0] c0000000000f0d28 worker_thread+0x148/0x610
[c00000041f157d80] c0000000000f96b0 kthread+0x120/0x140
[c00000041f157e30] c00000000000c0e0 ret_from_kernel_thread+0x5c/0x7c
This patch simply delays the MSR[TS] set, so, if there is any page fault in
the __get_user() section, it does not have regs->msr[TS] set, since the TM
structures are still invalid, thus avoiding doing TM operations for
in-kernel exceptions and possible process reschedule.
With this patch, the MSR[TS] will only be set just before recheckpointing
and setting TEXASR[FS] = 1, thus avoiding an interrupt with TM registers in
invalid state.
Other than that, if CONFIG_PREEMPT is set, there might be a preemption just
after setting MSR[TS] and before tm_recheckpoint(), thus, this block must
be atomic from a preemption perspective, thus, calling
preempt_disable/enable() on this code.
It is not possible to move tm_recheckpoint to happen earlier, because it is
required to get the checkpointed registers from userspace, with
__get_user(), thus, the only way to avoid this undesired behavior is
delaying the MSR[TS] set.
The 32-bits signal handler seems to be safe this current issue, but, it
might be exposed to the preemption issue, thus, disabling preemption in
this chunk of code.
Changes from v2:
* Run the critical section with preempt_disable.
Fixes: 87b4e5393a ("powerpc/tm: Fix return of active 64bit signals")
Cc: stable@vger.kernel.org (v3.9+)
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For fadump to work successfully there should not be any holes in reserved
memory ranges where kernel has asked firmware to move the content of old
kernel memory in event of crash. Now that fadump uses CMA for reserved
area, this memory area is now not protected from hot-remove operations
unless it is cma allocated. Hence, fadump service can fail to re-register
after the hot-remove operation, if hot-removed memory belongs to fadump
reserved region. To avoid this make sure that memory from fadump reserved
area is not hot-removable if fadump is registered.
However, if user still wants to remove that memory, he can do so by
manually stopping fadump service before hot-remove operation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
fadump fails to register when there are holes in reserved memory area.
This can happen if user has hot-removed a memory that falls in the
fadump reserved memory area. Throw a meaningful error message to the
user in such case.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
[mpe: is_reserved_memory_area_contiguous() returns bool, unsplit string]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
One of the primary issues with Firmware Assisted Dump (fadump) on Power
is that it needs a large amount of memory to be reserved. On large
systems with TeraBytes of memory, this reservation can be quite
significant.
In some cases, fadump fails if the memory reserved is insufficient, or
if the reserved memory was DLPAR hot-removed.
In the normal case, post reboot, the preserved memory is filtered to
extract only relevant areas of interest using the makedumpfile tool.
While the tool provides flexibility to determine what needs to be part
of the dump and what memory to filter out, all supported distributions
default this to "Capture only kernel data and nothing else".
We take advantage of this default and the Linux kernel's Contiguous
Memory Allocator (CMA) to fundamentally change the memory reservation
model for fadump.
Instead of setting aside a significant chunk of memory nobody can use,
this patch uses CMA instead, to reserve a significant chunk of memory
that the kernel is prevented from using (due to MIGRATE_CMA), but
applications are free to use it. With this fadump will still be able
to capture all of the kernel memory and most of the user space memory
except the user pages that were present in CMA region.
Essentially, on a P9 LPAR with 2 cores, 8GB RAM and current upstream:
[root@zzxx-yy10 ~]# free -m
total used free shared buff/cache available
Mem: 7557 193 6822 12 541 6725
Swap: 4095 0 4095
With this patch:
[root@zzxx-yy10 ~]# free -m
total used free shared buff/cache available
Mem: 8133 194 7464 12 475 7338
Swap: 4095 0 4095
Changes made here are completely transparent to how fadump has
traditionally worked.
Thanks to Aneesh Kumar and Anshuman Khandual for helping us understand
CMA and its usage.
TODO:
- Handle case where CMA reservation spans nodes.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The main new feature this time is support in HV nested KVM for passing
a device that is emulated by a level 0 hypervisor and presented to
level 1 as a PCI device through to a level 2 guest using VFIO.
Apart from that there are improvements for migration of radix guests
under HV KVM and some other fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJcGFzEAAoJEJ2a6ncsY3GfKjoH/Azcf8QIO5ftyHrjazFZOSUh
5Lr24HZTYHheowp6obzuZWRAIyckHmflRmOkv8RVGuA8+Sp+m5pBxN3WTVPOwDUh
WanOWVGJsuhl6qATmkm7xIxmYhQEyLxVNbnWva7WXuZ92rgGCNfHtByHWAx/7vTe
q5Shr4fLIQ8HRzor8Xqqph1I0hQNTE9VsaK1hW/PxI0gsO8qjDwOR8SDpT/aaJrS
Sir+lM0TwCbJREuObDxYAXn1OWy8rMYjlb9fEBv5tmPCQKiB9vJz4tV+ahR9eJ14
PEF57MoBOGwzQXo4geFLuo/Bu8fDygKsKQX1eYGcn6tRGA4pnTxzYl0+dHLBkOM=
=3WkD
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
PPC KVM update for 4.21 from Paul Mackerras
The main new feature this time is support in HV nested KVM for passing
a device that is emulated by a level 0 hypervisor and presented to
level 1 as a PCI device through to a level 2 guest using VFIO.
Apart from that there are improvements for migration of radix guests
under HV KVM and some other fixes and cleanups.
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Report branch predictor state flush as a mitigation for
Spectre variant 2.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the user choses not to use the mitigations, replace
the code sequence with nops.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to protect against speculation attacks on
indirect branches, the branch predictor is flushed at
kernel entry to protect for the following situations:
- userspace process attacking another userspace process
- userspace process attacking the kernel
Basically when the privillege level change (i.e.the kernel
is entered), the branch predictor state is flushed.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to protect against speculation attacks on
indirect branches, the branch predictor is flushed at
kernel entry to protect for the following situations:
- userspace process attacking another userspace process
- userspace process attacking the kernel
Basically when the privillege level change (i.e. the
kernel is entered), the branch predictor state is flushed.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the command line argument is present, the Spectre variant 2
mitigations are disabled.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently for CONFIG_PPC_FSL_BOOK3E the spectre_v2 file is incorrect:
$ cat /sys/devices/system/cpu/vulnerabilities/spectre_v2
"Mitigation: Software count cache flush"
Which is wrong. Fix it to report vulnerable for now.
Fixes: ee13cb249f ("powerpc/64s: Add support for software count cache flush")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to protect against speculation attacks (Spectre
variant 2) on NXP PowerPC platforms, the branch predictor
should be flushed when the privillege level is changed.
This patch is adding the infrastructure to fixup at runtime
the code sections that are performing the branch predictor flush
depending on a boot arg parameter which is added later in a
separate patch.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the device tree doesn't reside in the memory which is declared
inside it, it has to be moved as well as this memory will not be
mapped by the kernel.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For this use case, completions and semaphores are equivalent,
but semaphores are an awkward interface that should generally
be avoided, so use the completion instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Combine the SYSCALL_EMU and SYSCALL_TRACE handling so that we only
call tracehook_report_syscall_entry() in one place.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
[mpe: Flesh out change log, s/cached_flags/flags/, reflow comments]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Powerpc has somewhat odd usage where ZONE_DMA is used for all memory on
common 64-bit configfs, and ZONE_DMA32 is used for 31-bit schemes.
Move to a scheme closer to what other architectures use (and I dare to
say the intent of the system):
- ZONE_DMA: optionally for memory < 31-bit (64-bit embedded only)
- ZONE_NORMAL: everything addressable by the kernel
- ZONE_HIGHMEM: memory > 32-bit for 32-bit kernels
Also provide information on how ZONE_DMA is used by defining
ARCH_ZONE_DMA_BITS.
Contains various fixes from Benjamin Herrenschmidt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The implemementation for the CONFIG_NOT_COHERENT_CACHE case doesn't share
any code with the one for systems with coherent caches. Split it off
and merge it with the helpers in dma-noncoherent.c that have no other
callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The unmap methods need to transfer memory ownership back from the
device to the cpu by identical means as dma_sync_*_to_cpu. I'm not
sure powerpc needs to do any work in this transfer direction, but
given that it does invalidate the caches in dma_sync_*_to_cpu already
we should make sure we also do so on unmapping.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[mpe: s/dir/direction in dma_nommu_unmap_page()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes early DEBUG messages in prom.c:
- Use %px instead of %p to see the addresses
- Cast memblock_phys_mem_size() with (unsigned long long) to
avoid build failure when phys_addr_t is not 64 bits.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 603 doesn't have a HASH table, TLB misses are handled by
software. It is then possible to generate page fault when
_PAGE_EXEC is not set like in nohash/32.
There is one "reserved" PTE bit available, this patch uses
it for _PAGE_EXEC.
In order to support it, set_pte_filter() and
set_access_flags_filter() are made common, and the handling
is made dependent on MMU_FTR_HPTE_TABLE
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit f21f49ea63 ("[POWERPC] Remove the dregs of APUS support from
arch/powerpc") removed CONFIG_APUS, but forgot to remove the logic
which adapts tophys() and tovirt() for it.
This patch removes the last stale pieces.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch sites and associated helpers to manage TLB handlers
patching instead of hardcoding.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of manually patching a blr at hash_page() entry in
MMU_init_hw(), this patch adds a features section in head_32.S
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch_site_addr() instead of hardcoding the
address calculation in machine_init()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch again, this has a couple of build fixes and also
a change to do_syscall_trace_enter() that will conflict with a patch we
want to apply in next.
Use the new function to replace the open-coded iommu check.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell Currey <ruscur@russell.cc>
Cc: Sam Bobroff <sbobroff@linux.ibm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The POWER9 radix mmu has the concept of quadrants. The quadrant number
is the two high bits of the effective address and determines the fully
qualified address to be used for the translation. The fully qualified
address consists of the effective lpid, the effective pid and the
effective address. This gives then 4 possible quadrants 0, 1, 2, and 3.
When accessing these quadrants the fully qualified address is obtained
as follows:
Quadrant | Hypervisor | Guest
--------------------------------------------------------------------------
| EA[0:1] = 0b00 | EA[0:1] = 0b00
0 | effLPID = 0 | effLPID = LPIDR
| effPID = PIDR | effPID = PIDR
--------------------------------------------------------------------------
| EA[0:1] = 0b01 |
1 | effLPID = LPIDR | Invalid Access
| effPID = PIDR |
--------------------------------------------------------------------------
| EA[0:1] = 0b10 |
2 | effLPID = LPIDR | Invalid Access
| effPID = 0 |
--------------------------------------------------------------------------
| EA[0:1] = 0b11 | EA[0:1] = 0b11
3 | effLPID = 0 | effLPID = LPIDR
| effPID = 0 | effPID = 0
--------------------------------------------------------------------------
In the Guest;
Quadrant 3 is normally used to address the operating system since this
uses effPID=0 and effLPID=LPIDR, meaning the PID register doesn't need to
be switched.
Quadrant 0 is normally used to address user space since the effLPID and
effPID are taken from the corresponding registers.
In the Host;
Quadrant 0 and 3 are used as above, however the effLPID is always 0 to
address the host.
Quadrants 1 and 2 can be used by the host to address guest memory using
a guest effective address. Since the effLPID comes from the LPID register,
the host loads the LPID of the guest it would like to access (and the
PID of the process) and can perform accesses to a guest effective
address.
This means quadrant 1 can be used to address the guest user space and
quadrant 2 can be used to address the guest operating system from the
hypervisor, using a guest effective address.
Access to the quadrants can cause a Hypervisor Data Storage Interrupt
(HDSI) due to being unable to perform partition scoped translation.
Previously this could only be generated from a guest and so the code
path expects us to take the KVM trampoline in the interrupt handler.
This is no longer the case so we modify the handler to call
bad_page_fault() to check if we were expecting this fault so we can
handle it gracefully and just return with an error code. In the hash mmu
case we still raise an unknown exception since quadrants aren't defined
for the hash mmu.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
One notable fix for our change to split pt_regs between user/kernel, we forgot
to update BPF to use the user-visible type which was an ABI break for BPF
programs.
A slightly ugly but minimal fix to do_syscall_trace_enter() so that we use
tracehook_report_syscall_entry() properly. We'll rework the code in next to
avoid the empty if body.
Seven commits fixing bugs in the new papr_scm (Storage Class Memory) driver.
The driver was finally able to be tested on the other hypervisor which exposed
several bugs. The fixes are all fairly minimal at least.
Fix a crash in our MSI code if an MSI-capable device is plugged into a non-MSI
capable PHB, only seen on older hardware (MPC8378).
Fix our legacy serial code to look for "stdout-path" since the device trees were
updated to use that instead of "linux,stdout-path".
A change to the COFF zImage code to fix booting old powermacs.
A couple of minor build fixes.
Thanks to:
Benjamin Herrenschmidt, Daniel Axtens, Dmitry V. Levin, Elvira Khabirova,
Oliver O'Halloran, Paul Mackerras, Radu Rendec, Rob Herring, Sandipan Das.
-----BEGIN PGP SIGNATURE-----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=wI/G
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One notable fix for our change to split pt_regs between user/kernel,
we forgot to update BPF to use the user-visible type which was an ABI
break for BPF programs.
A slightly ugly but minimal fix to do_syscall_trace_enter() so that we
use tracehook_report_syscall_entry() properly. We'll rework the code
in next to avoid the empty if body.
Seven commits fixing bugs in the new papr_scm (Storage Class Memory)
driver. The driver was finally able to be tested on the other
hypervisor which exposed several bugs. The fixes are all fairly
minimal at least.
Fix a crash in our MSI code if an MSI-capable device is plugged into a
non-MSI capable PHB, only seen on older hardware (MPC8378).
Fix our legacy serial code to look for "stdout-path" since the device
trees were updated to use that instead of "linux,stdout-path".
A change to the COFF zImage code to fix booting old powermacs.
A couple of minor build fixes.
Thanks to: Benjamin Herrenschmidt, Daniel Axtens, Dmitry V. Levin,
Elvira Khabirova, Oliver O'Halloran, Paul Mackerras, Radu Rendec, Rob
Herring, Sandipan Das"
* tag 'powerpc-4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/ptrace: replace ptrace_report_syscall() with a tracehook call
powerpc/mm: Fallback to RAM if the altmap is unusable
powerpc/papr_scm: Use ibm,unit-guid as the iset cookie
powerpc/papr_scm: Fix DIMM device registration race
powerpc/papr_scm: Remove endian conversions
powerpc/papr_scm: Update DT properties
powerpc/papr_scm: Fix resource end address
powerpc/papr_scm: Use depend instead of select
powerpc/bpf: Fix broken uapi for BPF_PROG_TYPE_PERF_EVENT
powerpc/boot: Fix build failures with -j 1
powerpc: Look for "stdout-path" when setting up legacy consoles
powerpc/msi: Fix NULL pointer access in teardown code
powerpc/mm: Fix linux page tables build with some configs
powerpc: Fix COFF zImage booting on old powermacs
While the dma-direct code is (relatively) clean and simple we actually
have to use the swiotlb ops for the mapping on many architectures due
to devices with addressing limits. Instead of keeping two
implementations around this commit allows the dma-direct
implementation to call the swiotlb bounce buffering functions and
thus share the guts of the mapping implementation. This also
simplified the dma-mapping setup on a few architectures where we
don't have to differenciate which implementation to use.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Arch code should use tracehook_*() helpers, as documented in
include/linux/tracehook.h, ptrace_report_syscall() is not expected to
be used outside that file.
The patch does not look very nice, but at least it is correct
and opens the way for PTRACE_GET_SYSCALL_INFO API.
Co-authored-by: Dmitry V. Levin <ldv@altlinux.org>
Fixes: 5521eb4bca ("powerpc/ptrace: Add support for PTRACE_SYSEMU")
Signed-off-by: Elvira Khabirova <lineprinter@altlinux.org>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
[mpe: Take this as a minimal fix for 4.20, we'll rework it later]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powerpc iommu code already returns (~(dma_addr_t)0x0) on mapping
failures, so we can switch over to returning DMA_MAPPING_ERROR and let
the core dma-mapping code handle the rest.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
The dma-direct code already returns (~(dma_addr_t)0x0) on mapping
failures, so we can switch over to returning DMA_MAPPING_ERROR and let
the core dma-mapping code handle the rest.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Memblock list is another source for usable system memory layout.
So move powerpc's arch_kexec_walk_mem() to common code so that other
memblock-based architectures, particularly arm64, can also utilise it.
A moved function is now renamed to kexec_walk_memblock() and integrated
into kexec_locate_mem_hole(), which will now be usable for all
architectures with no need for overriding arch_kexec_walk_mem().
With this change, arch_kexec_walk_mem() need no longer be a weak function,
and was now renamed to kexec_walk_resources().
Since powerpc doesn't support kdump in its kexec_file_load(), the current
kexec_walk_memblock() won't work for kdump either in this form, this will
be fixed in the next patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As this is running with MMU off, the CPU only does speculative
fetch for code in the same page.
Following the significant size reduction of TLB handler routines,
the side handlers can be brought back close to the main part,
ie in the same page.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch reworks the TLB Miss handler in order to not use r12
register, hence avoiding having to save it into SPRN_SPRG_SCRATCH2.
In the DAR Fixup code we can now use SPRN_M_TW, freeing
SPRN_SPRG_SCRATCH2.
Then SPRN_SPRG_SCRATCH2 may be used for something else in the future.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Today, on the 8xx the TLB handlers do SW tablewalk by doing all
the calculation in ASM, in order to match with the Linux page
table structure.
The 8xx offers hardware assistance which allows significant size
reduction of the TLB handlers, hence also reduces the time spent
in the handlers.
However, using this HW assistance implies some constraints on the
page table structure:
- Regardless of the main page size used (4k or 16k), the
level 1 table (PGD) contains 1024 entries and each PGD entry covers
a 4Mbytes area which is managed by a level 2 table (PTE) containing
also 1024 entries each describing a 4k page.
- 16k pages require 4 identifical entries in the L2 table
- 512k pages PTE have to be spread every 128 bytes in the L2 table
- 8M pages PTE are at the address pointed by the L1 entry and each
8M page require 2 identical entries in the PGD.
This patch modifies the TLB handlers to use HW assistance for 4K PAGES.
Before that patch, the mean time spent in TLB miss handlers is:
- ITLB miss: 80 ticks
- DTLB miss: 62 ticks
After that patch, the mean time spent in TLB miss handlers is:
- ITLB miss: 72 ticks
- DTLB miss: 54 ticks
So the improvement is 10% for ITLB and 13% for DTLB misses
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In preparation of making use of hardware assistance in TLB handlers,
this patch temporarily disables 16K pages and hugepages. The reason
is that when using HW assistance in 4K pages mode, the linux model
fit with the HW model for 4K pages and 8M pages.
However for 16K pages and 512K mode some additional work is needed
to get linux model fit with HW model.
For the 8M pages, they will naturaly come back when we switch to
HW assistance, without any additional handling.
In order to keep the following patch smaller, the removal of the
current special handling for 8M pages gets removed here as well.
Therefore the 4K pages mode will be implemented first and without
support for 512k hugepages. Then the 512k hugepages will be brought
back. And the 16K pages will be implemented in the following step.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to simplify time critical exceptions handling 8xx
specific SW perf counters, this patch moves the counters into
the beginning of memory. This is possible because .text is readable
and the counters are never modified outside of the handlers.
By doing this, we avoid having to set a second register with
the upper part of the address of the counters.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The purpose of this patch is to move platform specific
mmu-xxx.h files in platform directories like pte-xxx.h files.
In the meantime this patch creates common nohash and
nohash/32 + nohash/64 mmu.h files for future common parts.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a plan to build the kernel with -Wimplicit-fallthrough and these
places in the code produced warnings, but because we build arch/powerpc
with -Werror, they became errors. Fix them up.
This patch produces no change in behaviour, but should be reviewed in
case these are actually bugs not intentional fallthoughs.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of running with interrupts disabled, use a semaphore. This should
make it easier for backends that may need to sleep (e.g. EFI) when
performing a write:
|BUG: sleeping function called from invalid context at kernel/sched/completion.c:99
|in_atomic(): 1, irqs_disabled(): 1, pid: 2236, name: sig-xstate-bum
|Preemption disabled at:
|[<ffffffff99d60512>] pstore_dump+0x72/0x330
|CPU: 26 PID: 2236 Comm: sig-xstate-bum Tainted: G D 4.20.0-rc3 #45
|Call Trace:
| dump_stack+0x4f/0x6a
| ___might_sleep.cold.91+0xd3/0xe4
| __might_sleep+0x50/0x90
| wait_for_completion+0x32/0x130
| virt_efi_query_variable_info+0x14e/0x160
| efi_query_variable_store+0x51/0x1a0
| efivar_entry_set_safe+0xa3/0x1b0
| efi_pstore_write+0x109/0x140
| pstore_dump+0x11c/0x330
| kmsg_dump+0xa4/0xd0
| oops_exit+0x22/0x30
...
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Fixes: 21b3ddd39f ("efi: Don't use spinlocks for efi vars")
Signed-off-by: Kees Cook <keescook@chromium.org>
Commit 78e5dfea84 ("powerpc: dts: replace 'linux,stdout-path' with
'stdout-path'") broke the default console on a number of embedded
PowerPC systems, because it failed to also update the code in
arch/powerpc/kernel/legacy_serial.c to look for that property in
addition to the old one.
This fixes it.
Fixes: 78e5dfea84 ("powerpc: dts: replace 'linux,stdout-path' with 'stdout-path'")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The arch_teardown_msi_irqs() function assumes that controller ops
pointers were already checked in arch_setup_msi_irqs(), but this
assumption is wrong: arch_teardown_msi_irqs() can be called even when
arch_setup_msi_irqs() returns an error (-ENOSYS).
This can happen in the following scenario:
- msi_capability_init() calls pci_msi_setup_msi_irqs()
- pci_msi_setup_msi_irqs() returns -ENOSYS
- msi_capability_init() notices the error and calls free_msi_irqs()
- free_msi_irqs() calls pci_msi_teardown_msi_irqs()
This is easier to see when CONFIG_PCI_MSI_IRQ_DOMAIN is not set and
pci_msi_setup_msi_irqs() and pci_msi_teardown_msi_irqs() are just
aliases to arch_setup_msi_irqs() and arch_teardown_msi_irqs().
The call to free_msi_irqs() upon pci_msi_setup_msi_irqs() failure
seems legit, as it does additional cleanup; e.g.
list_del(&entry->list) and kfree(entry) inside free_msi_irqs() do
happen (MSI descriptors are allocated before pci_msi_setup_msi_irqs()
is called and need to be cleaned up if that fails).
Fixes: 6b2fd7efeb ("PCI/MSI/PPC: Remove arch_msi_check_device()")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function_graph_enter() function does the work of calling the function
graph hook function and the management of the shadow stack, simplifying the
work done in the architecture dependent prepare_ftrace_return().
Have powerpc use the new code, and remove the shadow stack management as well as
having to set up the trace structure.
This is needed to prepare for a fix of a design bug on how the curr_ret_stack
is used.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: stable@kernel.org
Fixes: 03274a3ffb ("tracing/fgraph: Adjust fgraph depth before calling trace return callback")
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Today we have:
config PPC_BOOK3S_32
bool "512x/52xx/6xx/7xx/74xx/82xx/83xx/86xx"
[depends on PPC32 within a choice]
config PPC_BOOK3S
def_bool y
depends on PPC_BOOK3S_32 || PPC_BOOK3S_64
config PPC_STD_MMU
def_bool y
depends on PPC_BOOK3S
config PPC_STD_MMU_32
def_bool y
depends on PPC_STD_MMU && PPC32
PPC_STD_MMU_32 is therefore redundant with PPC_BOOK3S_32.
In order to make the code clearer, lets use preferably PPC_BOOK3S_32.
This will allow to remove CONFIG_PPC_STD_MMU_32 in a later patch.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Today we have:
config PPC_BOOK3S_32
bool "512x/52xx/6xx/7xx/74xx/82xx/83xx/86xx"
[depends on PPC32 within a choice]
config PPC_BOOK3S
def_bool y
depends on PPC_BOOK3S_32 || PPC_BOOK3S_64
config 6xx
def_bool y
depends on PPC32 && PPC_BOOK3S
6xx is therefore redundant with PPC_BOOK3S_32.
In order to make the code clearer, lets use preferably PPC_BOOK3S_32.
This will allow to remove CONFIG_6xx in a later patch.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove directly accessing device_node.type pointer and use the
accessors instead. This will eventually allow removing the type
pointer.
Replace the open coded iterating over child nodes with
for_each_child_of_node() while we're here.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove directly accessing device_node.type pointer and use the
accessors instead. This will eventually allow removing the type
pointer.
In the process, the of_stdout pointer can be used instead of finding
the stdout node again.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no need to have the 'intoffset' variable static since new value
always be assigned before use it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When both `CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y` and `CONFIG_UBSAN=y`
are set, link step typically produce numberous warnings about orphan
section:
+ powerpc-linux-gnu-ld -EB -m elf32ppc -Bstatic --orphan-handling=warn --build-id --gc-sections -X -o .tmp_vmlinux1 -T ./arch/powerpc/kernel/vmlinux.lds --who
le-archive built-in.a --no-whole-archive --start-group lib/lib.a --end-group
powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_data393' from `init/main.o' being placed in section `.data..Lubsan_data393'.
powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_data394' from `init/main.o' being placed in section `.data..Lubsan_data394'.
...
powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_type11' from `init/main.o' being placed in section `.data..Lubsan_type11'.
powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_type12' from `init/main.o' being placed in section `.data..Lubsan_type12'.
...
This commit remove those warnings produced at W=1.
Link: https://www.mail-archive.com/linuxppc-dev@lists.ozlabs.org/msg135407.html
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function pci_ers_result_name() is a static function, although not declared
as such. This was detected by sparse in the following warning
arch/powerpc/kernel/eeh_driver.c:63:12: warning: symbol 'pci_ers_result_name' was not declared. Should it be static?
This patch simply declares the function a static.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Current powerpc security.c file is defining functions, as
cpu_show_meltdown(), cpu_show_spectre_v{1,2} and others, that are being
declared at linux/cpu.h header without including the header file that
contains these declarations.
This is being reported by sparse, which thinks that these functions are
static, due to the lack of declaration:
arch/powerpc/kernel/security.c:105:9: warning: symbol 'cpu_show_meltdown' was not declared. Should it be static?
arch/powerpc/kernel/security.c:139:9: warning: symbol 'cpu_show_spectre_v1' was not declared. Should it be static?
arch/powerpc/kernel/security.c:161:9: warning: symbol 'cpu_show_spectre_v2' was not declared. Should it be static?
arch/powerpc/kernel/security.c:209:6: warning: symbol 'stf_barrier' was not declared. Should it be static?
arch/powerpc/kernel/security.c:289:9: warning: symbol 'cpu_show_spec_store_bypass' was not declared. Should it be static?
This patch simply includes the proper header (linux/cpu.h) to match
function definition and declaration.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 4c2de74cc8 ("powerpc/64: Interrupts save PPR on stack rather
than thread_struct") changed sizeof(struct pt_regs) % 16 from 0 to 8,
which causes the interrupt frame allocation on kernel entry to put the
kernel stack out of alignment.
Quadword (16-byte) alignment for the stack is required by both the
64-bit v1 ABI (v1.9 § 3.2.2) and the 64-bit v2 ABI (v1.1 § 2.2.2.1).
Add a pad field to fix alignment, and add a BUILD_BUG_ON to catch this
in future.
Fixes: 4c2de74cc8 ("powerpc/64: Interrupts save PPR on stack rather than thread_struct")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some things that I missed due to travel, or that came in late.
Two fixes also going to stable:
- A revert of a buggy change to the 8xx TLB miss handlers.
- Our flushing of SPE (Signal Processing Engine) registers on fork was broken.
Other changes:
- A change to the KVM decrementer emulation to use proper APIs.
- Some cleanups to the way we do code patching in the 8xx code.
- Expose the maximum possible memory for the system in /proc/powerpc/lparcfg.
- Merge some updates from Scott: "a couple device tree updates, and a fix for a
missing prototype warning."
A few other minor fixes and a handful of fixes for our selftests.
Thanks to:
Aravinda Prasad, Breno Leitao, Camelia Groza, Christophe Leroy, Felipe Rechia,
Joel Stanley, Naveen N. Rao, Paul Mackerras, Scott Wood, Tyrel Datwyler.
-----BEGIN PGP SIGNATURE-----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=VCkW
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some things that I missed due to travel, or that came in late.
Two fixes also going to stable:
- A revert of a buggy change to the 8xx TLB miss handlers.
- Our flushing of SPE (Signal Processing Engine) registers on fork
was broken.
Other changes:
- A change to the KVM decrementer emulation to use proper APIs.
- Some cleanups to the way we do code patching in the 8xx code.
- Expose the maximum possible memory for the system in
/proc/powerpc/lparcfg.
- Merge some updates from Scott: "a couple device tree updates, and a
fix for a missing prototype warning"
A few other minor fixes and a handful of fixes for our selftests.
Thanks to: Aravinda Prasad, Breno Leitao, Camelia Groza, Christophe
Leroy, Felipe Rechia, Joel Stanley, Naveen N. Rao, Paul Mackerras,
Scott Wood, Tyrel Datwyler"
* tag 'powerpc-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (21 commits)
selftests/powerpc: Fix compilation issue due to asm label
selftests/powerpc/cache_shape: Fix out-of-tree build
selftests/powerpc/switch_endian: Fix out-of-tree build
selftests/powerpc/pmu: Link ebb tests with -no-pie
selftests/powerpc/signal: Fix out-of-tree build
selftests/powerpc/ptrace: Fix out-of-tree build
powerpc/xmon: Relax frame size for clang
selftests: powerpc: Fix warning for security subdir
selftests/powerpc: Relax L1d miss targets for rfi_flush test
powerpc/process: Fix flush_all_to_thread for SPE
powerpc/pseries: add missing cpumask.h include file
selftests/powerpc: Fix ptrace tm failure
KVM: PPC: Use exported tb_to_ns() function in decrementer emulation
powerpc/pseries: Export maximum memory value
powerpc/8xx: Use patch_site for perf counters setup
powerpc/8xx: Use patch_site for memory setup patching
powerpc/code-patching: Add a helper to get the address of a patch_site
Revert "powerpc/8xx: Use L1 entry APG to handle _PAGE_ACCESSED for CONFIG_SWAP"
powerpc/8xx: add missing header in 8xx_mmu.c
powerpc/8xx: Add DT node for using the SEC engine of the MPC885
...
When a memblock allocation APIs are called with align = 0, the alignment
is implicitly set to SMP_CACHE_BYTES.
Implicit alignment is done deep in the memblock allocator and it can
come as a surprise. Not that such an alignment would be wrong even
when used incorrectly but it is better to be explicit for the sake of
clarity and the prinicple of the least surprise.
Replace all such uses of memblock APIs with the 'align' parameter
explicitly set to SMP_CACHE_BYTES and stop implicit alignment assignment
in the memblock internal allocation functions.
For the case when memblock APIs are used via helper functions, e.g. like
iommu_arena_new_node() in Alpha, the helper functions were detected with
Coccinelle's help and then manually examined and updated where
appropriate.
The direct memblock APIs users were updated using the semantic patch below:
@@
expression size, min_addr, max_addr, nid;
@@
(
|
- memblock_alloc_try_nid_raw(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_raw(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid_nopanic(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_nopanic(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid(size, SMP_CACHE_BYTES, min_addr, max_addr, nid)
|
- memblock_alloc(size, 0)
+ memblock_alloc(size, SMP_CACHE_BYTES)
|
- memblock_alloc_raw(size, 0)
+ memblock_alloc_raw(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from(size, 0, min_addr)
+ memblock_alloc_from(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_nopanic(size, 0)
+ memblock_alloc_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low(size, 0)
+ memblock_alloc_low(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low_nopanic(size, 0)
+ memblock_alloc_low_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from_nopanic(size, 0, min_addr)
+ memblock_alloc_from_nopanic(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_node(size, 0, nid)
+ memblock_alloc_node(size, SMP_CACHE_BYTES, nid)
)
[mhocko@suse.com: changelog update]
[akpm@linux-foundation.org: coding-style fixes]
[rppt@linux.ibm.com: fix missed uses of implicit alignment]
Link: http://lkml.kernel.org/r/20181016133656.GA10925@rapoport-lnx
Link: http://lkml.kernel.org/r/1538687224-17535-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make it explicit that the caller gets a physical address rather than a
virtual one.
This will also allow using meblock_alloc prefix for memblock allocations
returning virtual address, which is done in the following patches.
The conversion is done using the following semantic patch:
@@
expression e1, e2, e3;
@@
(
- memblock_alloc(e1, e2)
+ memblock_phys_alloc(e1, e2)
|
- memblock_alloc_nid(e1, e2, e3)
+ memblock_phys_alloc_nid(e1, e2, e3)
|
- memblock_alloc_try_nid(e1, e2, e3)
+ memblock_phys_alloc_try_nid(e1, e2, e3)
)
Link: http://lkml.kernel.org/r/1536927045-23536-7-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Notable changes:
- A large series to rewrite our SLB miss handling, replacing a lot of fairly
complicated asm with much fewer lines of C.
- Following on from that, we now maintain a cache of SLB entries for each
process and preload them on context switch. Leading to a 27% speedup for our
context switch benchmark on Power9.
- Improvements to our handling of SLB multi-hit errors. We now print more debug
information when they occur, and try to continue running by flushing the SLB
and reloading, rather than treating them as fatal.
- Enable THP migration on 64-bit Book3S machines (eg. Power7/8/9).
- Add support for physical memory up to 2PB in the linear mapping on 64-bit
Book3S. We only support up to 512TB as regular system memory, otherwise the
percpu allocator runs out of vmalloc space.
- Add stack protector support for 32 and 64-bit, with a per-task canary.
- Add support for PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP.
- Support recognising "big cores" on Power9, where two SMT4 cores are presented
to us as a single SMT8 core.
- A large series to cleanup some of our ioremap handling and PTE flags.
- Add a driver for the PAPR SCM (storage class memory) interface, allowing
guests to operate on SCM devices (acked by Dan).
- Changes to our ftrace code to handle very large kernels, where we need to use
a trampoline to get to ftrace_caller().
Many other smaller enhancements and cleanups.
Thanks to:
Alan Modra, Alistair Popple, Aneesh Kumar K.V, Anton Blanchard, Aravinda
Prasad, Bartlomiej Zolnierkiewicz, Benjamin Herrenschmidt, Breno Leitao,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Dan Carpenter, Daniel
Axtens, Finn Thain, Gautham R. Shenoy, Gustavo Romero, Haren Myneni, Hari
Bathini, Jia Hongtao, Joel Stanley, John Allen, Laurent Dufour, Madhavan
Srinivasan, Mahesh Salgaonkar, Mark Hairgrove, Masahiro Yamada, Michael
Bringmann, Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers, Oliver O'Halloran,
Paul Mackerras, Petr Vorel, Rashmica Gupta, Reza Arbab, Rob Herring, Sam
Bobroff, Samuel Mendoza-Jonas, Scott Wood, Stan Johnson, Stephen Rothwell,
Stewart Smith, Suraj Jitindar Singh, Tyrel Datwyler, Vaibhav Jain, Vasant
Hegde, YueHaibing, zhong jiang,
-----BEGIN PGP SIGNATURE-----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=I0pj
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A large series to rewrite our SLB miss handling, replacing a lot of
fairly complicated asm with much fewer lines of C.
- Following on from that, we now maintain a cache of SLB entries for
each process and preload them on context switch. Leading to a 27%
speedup for our context switch benchmark on Power9.
- Improvements to our handling of SLB multi-hit errors. We now print
more debug information when they occur, and try to continue running
by flushing the SLB and reloading, rather than treating them as
fatal.
- Enable THP migration on 64-bit Book3S machines (eg. Power7/8/9).
- Add support for physical memory up to 2PB in the linear mapping on
64-bit Book3S. We only support up to 512TB as regular system
memory, otherwise the percpu allocator runs out of vmalloc space.
- Add stack protector support for 32 and 64-bit, with a per-task
canary.
- Add support for PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP.
- Support recognising "big cores" on Power9, where two SMT4 cores are
presented to us as a single SMT8 core.
- A large series to cleanup some of our ioremap handling and PTE
flags.
- Add a driver for the PAPR SCM (storage class memory) interface,
allowing guests to operate on SCM devices (acked by Dan).
- Changes to our ftrace code to handle very large kernels, where we
need to use a trampoline to get to ftrace_caller().
And many other smaller enhancements and cleanups.
Thanks to: Alan Modra, Alistair Popple, Aneesh Kumar K.V, Anton
Blanchard, Aravinda Prasad, Bartlomiej Zolnierkiewicz, Benjamin
Herrenschmidt, Breno Leitao, Cédric Le Goater, Christophe Leroy,
Christophe Lombard, Dan Carpenter, Daniel Axtens, Finn Thain, Gautham
R. Shenoy, Gustavo Romero, Haren Myneni, Hari Bathini, Jia Hongtao,
Joel Stanley, John Allen, Laurent Dufour, Madhavan Srinivasan, Mahesh
Salgaonkar, Mark Hairgrove, Masahiro Yamada, Michael Bringmann,
Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers, Oliver
O'Halloran, Paul Mackerras, Petr Vorel, Rashmica Gupta, Reza Arbab,
Rob Herring, Sam Bobroff, Samuel Mendoza-Jonas, Scott Wood, Stan
Johnson, Stephen Rothwell, Stewart Smith, Suraj Jitindar Singh, Tyrel
Datwyler, Vaibhav Jain, Vasant Hegde, YueHaibing, zhong jiang"
* tag 'powerpc-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (221 commits)
Revert "selftests/powerpc: Fix out-of-tree build errors"
powerpc/msi: Fix compile error on mpc83xx
powerpc: Fix stack protector crashes on CPU hotplug
powerpc/traps: restore recoverability of machine_check interrupts
powerpc/64/module: REL32 relocation range check
powerpc/64s/radix: Fix radix__flush_tlb_collapsed_pmd double flushing pmd
selftests/powerpc: Add a test of wild bctr
powerpc/mm: Fix page table dump to work on Radix
powerpc/mm/radix: Display if mappings are exec or not
powerpc/mm/radix: Simplify split mapping logic
powerpc/mm/radix: Remove the retry in the split mapping logic
powerpc/mm/radix: Fix small page at boundary when splitting
powerpc/mm/radix: Fix overuse of small pages in splitting logic
powerpc/mm/radix: Fix off-by-one in split mapping logic
powerpc/ftrace: Handle large kernel configs
powerpc/mm: Fix WARN_ON with THP NUMA migration
selftests/powerpc: Fix out-of-tree build errors
powerpc/time: no steal_time when CONFIG_PPC_SPLPAR is not selected
powerpc/time: Only set CONFIG_ARCH_HAS_SCALED_CPUTIME on PPC64
powerpc/time: isolate scaled cputime accounting in dedicated functions.
...
- various swiotlb cleanups
- do not dip into the ѕwiotlb pool for dma coherent allocations
- add support for not cache coherent DMA to swiotlb
- switch ARM64 to use the generic swiotlb_dma_ops
-----BEGIN PGP SIGNATURE-----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=pI5p
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.20-1' of git://git.infradead.org/users/hch/dma-mapping
Pull more dma-mapping updates from Christoph Hellwig:
- various swiotlb cleanups
- do not dip into the ѕwiotlb pool for dma coherent allocations
- add support for not cache coherent DMA to swiotlb
- switch ARM64 to use the generic swiotlb_dma_ops
* tag 'dma-mapping-4.20-1' of git://git.infradead.org/users/hch/dma-mapping:
arm64: use the generic swiotlb_dma_ops
swiotlb: add support for non-coherent DMA
swiotlb: don't dip into swiotlb pool for coherent allocations
swiotlb: refactor swiotlb_map_page
swiotlb: use swiotlb_map_page in swiotlb_map_sg_attrs
swiotlb: merge swiotlb_unmap_page and unmap_single
swiotlb: remove the overflow buffer
swiotlb: do not panic on mapping failures
swiotlb: mark is_swiotlb_buffer static
swiotlb: remove a pointless comment
Fix a bug introduced by the creation of flush_all_to_thread() for
processors that have SPE (Signal Processing Engine) and use it to
compute floating-point operations.
>From userspace perspective, the problem was seen in attempts of
computing floating-point operations which should generate exceptions.
For example:
fork();
float x = 0.0 / 0.0;
isnan(x); // forked process returns False (should be True)
The operation above also should always cause the SPEFSCR FINV bit to
be set. However, the SPE floating-point exceptions were turned off
after a fork().
Kernel versions prior to the bug used flush_spe_to_thread(), which
first saves SPEFSCR register values in tsk->thread and then calls
giveup_spe(tsk).
After commit 579e633e76, the save_all() function was called first
to giveup_spe(), and then the SPEFSCR register values were saved in
tsk->thread. This would save the SPEFSCR register values after
disabling SPE for that thread, causing the bug described above.
Fixes 579e633e76 ("powerpc: create flush_all_to_thread()")
Signed-off-by: Felipe Rechia <felipe.rechia@datacom.com.br>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 8xx TLB miss routines are patched when (de)activating
perf counters.
This patch uses the new patch_site functionality in order
to get a better code readability and avoid a label mess when
dumping the code with 'objdump -d'
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 8xx TLB miss routines are patched at startup at several places.
This patch uses the new patch_site functionality in order
to get a better code readability and avoid a label mess when
dumping the code with 'objdump -d'
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 4f94b2c746.
That commit was buggy, as it used rlwinm instead of rlwimi.
Instead of fixing that bug, we revert the previous commit in order to
reduce the dependency between L1 entries and L2 entries
Fixes: 4f94b2c746 ("powerpc/8xx: Use L1 entry APG to handle _PAGE_ACCESSED for CONFIG_SWAP")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ARM:
- Improved guest IPA space support (32 to 52 bits)
- RAS event delivery for 32bit
- PMU fixes
- Guest entry hardening
- Various cleanups
- Port of dirty_log_test selftest
PPC:
- Nested HV KVM support for radix guests on POWER9. The performance is
much better than with PR KVM. Migration and arbitrary level of
nesting is supported.
- Disable nested HV-KVM on early POWER9 chips that need a particular hardware
bug workaround
- One VM per core mode to prevent potential data leaks
- PCI pass-through optimization
- merge ppc-kvm topic branch and kvm-ppc-fixes to get a better base
s390:
- Initial version of AP crypto virtualization via vfio-mdev
- Improvement for vfio-ap
- Set the host program identifier
- Optimize page table locking
x86:
- Enable nested virtualization by default
- Implement Hyper-V IPI hypercalls
- Improve #PF and #DB handling
- Allow guests to use Enlightened VMCS
- Add migration selftests for VMCS and Enlightened VMCS
- Allow coalesced PIO accesses
- Add an option to perform nested VMCS host state consistency check
through hardware
- Automatic tuning of lapic_timer_advance_ns
- Many fixes, minor improvements, and cleanups
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJb0FINAAoJEED/6hsPKofoI60IAJRS3vOAQ9Fav8cJsO1oBHcX
3+NexfnBke1bzrjIR3SUcHKGZbdnVPNZc+Q4JjIbPpPmmOMU5jc9BC1dmd5f4Vzh
BMnQ0yCvgFv3A3fy/Icx1Z8NJppxosdmqdQLrQrNo8aD3cjnqY2yQixdXrAfzLzw
XEgKdIFCCz8oVN/C9TT4wwJn6l9OE7BM5bMKGFy5VNXzMu7t64UDOLbbjZxNgi1g
teYvfVGdt5mH0N7b2GPPWRbJmgnz5ygVVpVNQUEFrdKZoCm6r5u9d19N+RRXAwan
ZYFj10W2T8pJOUf3tryev4V33X7MRQitfJBo4tP5hZfi9uRX89np5zP1CFE7AtY=
=yEPW
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.20-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"ARM:
- Improved guest IPA space support (32 to 52 bits)
- RAS event delivery for 32bit
- PMU fixes
- Guest entry hardening
- Various cleanups
- Port of dirty_log_test selftest
PPC:
- Nested HV KVM support for radix guests on POWER9. The performance
is much better than with PR KVM. Migration and arbitrary level of
nesting is supported.
- Disable nested HV-KVM on early POWER9 chips that need a particular
hardware bug workaround
- One VM per core mode to prevent potential data leaks
- PCI pass-through optimization
- merge ppc-kvm topic branch and kvm-ppc-fixes to get a better base
s390:
- Initial version of AP crypto virtualization via vfio-mdev
- Improvement for vfio-ap
- Set the host program identifier
- Optimize page table locking
x86:
- Enable nested virtualization by default
- Implement Hyper-V IPI hypercalls
- Improve #PF and #DB handling
- Allow guests to use Enlightened VMCS
- Add migration selftests for VMCS and Enlightened VMCS
- Allow coalesced PIO accesses
- Add an option to perform nested VMCS host state consistency check
through hardware
- Automatic tuning of lapic_timer_advance_ns
- Many fixes, minor improvements, and cleanups"
* tag 'kvm-4.20-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
KVM/nVMX: Do not validate that posted_intr_desc_addr is page aligned
Revert "kvm: x86: optimize dr6 restore"
KVM: PPC: Optimize clearing TCEs for sparse tables
x86/kvm/nVMX: tweak shadow fields
selftests/kvm: add missing executables to .gitignore
KVM: arm64: Safety check PSTATE when entering guest and handle IL
KVM: PPC: Book3S HV: Don't use streamlined entry path on early POWER9 chips
arm/arm64: KVM: Enable 32 bits kvm vcpu events support
arm/arm64: KVM: Rename function kvm_arch_dev_ioctl_check_extension()
KVM: arm64: Fix caching of host MDCR_EL2 value
KVM: VMX: enable nested virtualization by default
KVM/x86: Use 32bit xor to clear registers in svm.c
kvm: x86: Introduce KVM_CAP_EXCEPTION_PAYLOAD
kvm: vmx: Defer setting of DR6 until #DB delivery
kvm: x86: Defer setting of CR2 until #PF delivery
kvm: x86: Add payload operands to kvm_multiple_exception
kvm: x86: Add exception payload fields to kvm_vcpu_events
kvm: x86: Add has_payload and payload to kvm_queued_exception
KVM: Documentation: Fix omission in struct kvm_vcpu_events
KVM: selftests: add Enlightened VMCS test
...
Pull timekeeping updates from Thomas Gleixner:
"The timers and timekeeping departement provides:
- Another large y2038 update with further preparations for providing
the y2038 safe timespecs closer to the syscalls.
- An overhaul of the SHCMT clocksource driver
- SPDX license identifier updates
- Small cleanups and fixes all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
tick/sched : Remove redundant cpu_online() check
clocksource/drivers/dw_apb: Add reset control
clocksource: Remove obsolete CLOCKSOURCE_OF_DECLARE
clocksource/drivers: Unify the names to timer-* format
clocksource/drivers/sh_cmt: Add R-Car gen3 support
dt-bindings: timer: renesas: cmt: document R-Car gen3 support
clocksource/drivers/sh_cmt: Properly line-wrap sh_cmt_of_table[] initializer
clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines
clocksource/drivers/sh_cmt: Fixup for 64-bit machines
clocksource/drivers/sh_tmu: Convert to SPDX identifiers
clocksource/drivers/sh_mtu2: Convert to SPDX identifiers
clocksource/drivers/sh_cmt: Convert to SPDX identifiers
clocksource/drivers/renesas-ostm: Convert to SPDX identifiers
clocksource: Convert to using %pOFn instead of device_node.name
tick/broadcast: Remove redundant check
RISC-V: Request newstat syscalls
y2038: signal: Change rt_sigtimedwait to use __kernel_timespec
y2038: socket: Change recvmmsg to use __kernel_timespec
y2038: sched: Change sched_rr_get_interval to use __kernel_timespec
y2038: utimes: Rework #ifdef guards for compat syscalls
...
Pull security subsystem updates from James Morris:
"In this patchset, there are a couple of minor updates, as well as some
reworking of the LSM initialization code from Kees Cook (these prepare
the way for ordered stackable LSMs, but are a valuable cleanup on
their own)"
* 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
LSM: Don't ignore initialization failures
LSM: Provide init debugging infrastructure
LSM: Record LSM name in struct lsm_info
LSM: Convert security_initcall() into DEFINE_LSM()
vmlinux.lds.h: Move LSM_TABLE into INIT_DATA
LSM: Convert from initcall to struct lsm_info
LSM: Remove initcall tracing
LSM: Rename .security_initcall section to .lsm_info
vmlinux.lds.h: Avoid copy/paste of security_init section
LSM: Correctly announce start of LSM initialization
security: fix LSM description location
keys: Fix the use of the C++ keyword "private" in uapi/linux/keyctl.h
seccomp: remove unnecessary unlikely()
security: tomoyo: Fix obsolete function
security/capabilities: remove check for -EINVAL
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
Recently in commit 7241d26e81 ("powerpc/64: properly initialise
the stackprotector canary on SMP.") we fixed a crash with stack
protector on SMP by initialising the stack canary in
cpu_idle_thread_init().
But this can also causes crashes, when a CPU comes back online after
being offline:
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: pnv_smp_cpu_kill_self+0x2a0/0x2b0
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.19.0-rc3-gcc-7.3.1-00168-g4ffe713b7587 #94
Call Trace:
dump_stack+0xb0/0xf4 (unreliable)
panic+0x144/0x328
__stack_chk_fail+0x2c/0x30
pnv_smp_cpu_kill_self+0x2a0/0x2b0
cpu_die+0x48/0x70
arch_cpu_idle_dead+0x20/0x40
do_idle+0x274/0x390
cpu_startup_entry+0x38/0x50
start_secondary+0x5e4/0x600
start_secondary_prolog+0x10/0x14
Looking at the stack we see that the canary value in the stack frame
doesn't match the canary in the task/paca. That is because we have
reinitialised the task/paca value, but then the CPU coming online has
returned into a function using the old canary value. That causes the
comparison to fail.
Instead we can call boot_init_stack_canary() from start_secondary()
which never returns. This is essentially what the generic code does in
cpu_startup_entry() under #ifdef X86, we should make that non-x86
specific in a future patch.
Fixes: 7241d26e81 ("powerpc/64: properly initialise the stackprotector canary on SMP.")
Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
commit b96672dd84 ("powerpc: Machine check interrupt is a non-
maskable interrupt") added a call to nmi_enter() at the beginning of
machine check restart exception handler. Due to that, in_interrupt()
always returns true regardless of the state before entering the
exception, and die() panics even when the system was not already in
interrupt.
This patch calls nmi_exit() before calling die() in order to restore
the interrupt state we had before calling nmi_enter()
Fixes: b96672dd84 ("powerpc: Machine check interrupt is a non-maskable interrupt")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The recent module relocation overflow crash demonstrated that we
have no range checking on REL32 relative relocations. This patch
implements a basic check, the same kernel that previously oopsed
and rebooted now continues with some of these errors when loading
the module:
module_64: x_tables: REL32 527703503449812 out of range!
Possibly other relocations (ADDR32, REL16, TOC16, etc.) should also have
overflow checks.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, we expect to be able to reach ftrace_caller() from all
ftrace-enabled functions through a single relative branch. With large
kernel configs, we see functions outside of 32MB of ftrace_caller()
causing ftrace_init() to bail.
In such configurations, gcc/ld emits two types of trampolines for mcount():
1. A long_branch, which has a single branch to mcount() for functions that
are one hop away from mcount():
c0000000019e8544 <00031b56.long_branch._mcount>:
c0000000019e8544: 4a 69 3f ac b c00000000007c4f0 <._mcount>
2. A plt_branch, for functions that are farther away from mcount():
c0000000051f33f8 <0008ba04.plt_branch._mcount>:
c0000000051f33f8: 3d 82 ff a4 addis r12,r2,-92
c0000000051f33fc: e9 8c 04 20 ld r12,1056(r12)
c0000000051f3400: 7d 89 03 a6 mtctr r12
c0000000051f3404: 4e 80 04 20 bctr
We can reuse those trampolines for ftrace if we can have those
trampolines go to ftrace_caller() instead. However, with ABIv2, we
cannot depend on r2 being valid. As such, we use only the long_branch
trampolines by patching those to instead branch to ftrace_caller or
ftrace_regs_caller.
In addition, we add additional trampolines around .text and .init.text
to catch locations that are covered by the plt branches. This allows
ftrace to work with most large kernel configurations.
For now, we always patch the trampolines to go to ftrace_regs_caller,
which is slightly inefficient. This can be optimized further at a later
point.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If CONFIG_PPC_SPLPAR is not selected, steal_time will always
be NUL, so accounting it is pointless
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
scaled cputime is only meaningfull when the processor has
SPURR and/or PURR, which means only on PPC64.
Removing it on PPC32 significantly reduces the size of
vtime_account_system() and vtime_account_idle() on an 8xx:
Before:
00000000 l F .text 000000a8 vtime_delta
00000280 g F .text 0000010c vtime_account_system
0000038c g F .text 00000048 vtime_account_idle
After:
(vtime_delta gets inlined inside the two functions)
000001d8 g F .text 000000a0 vtime_account_system
00000278 g F .text 00000038 vtime_account_idle
In terms of performance, we also get approximatly 7% improvement on
task switch. The following small benchmark app is run with perf stat:
void *thread(void *arg)
{
int i;
for (i = 0; i < atoi((char*)arg); i++)
pthread_yield();
}
int main(int argc, char **argv)
{
pthread_t th1, th2;
pthread_create(&th1, NULL, thread, argv[1]);
pthread_create(&th2, NULL, thread, argv[1]);
pthread_join(th1, NULL);
pthread_join(th2, NULL);
return 0;
}
Before the patch:
Performance counter stats for 'chrt -f 98 ./sched 100000' (50 runs):
8228.476465 task-clock (msec) # 0.954 CPUs utilized ( +- 0.23% )
200004 context-switches # 0.024 M/sec ( +- 0.00% )
After the patch:
Performance counter stats for 'chrt -f 98 ./sched 100000' (50 runs):
7649.070444 task-clock (msec) # 0.955 CPUs utilized ( +- 0.27% )
200004 context-switches # 0.026 M/sec ( +- 0.00% )
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
scaled cputime is only meaningfull when the processor has
SPURR and/or PURR, which means only on PPC64.
In preparation of the following patch that will remove
CONFIG_ARCH_HAS_SCALED_CPUTIME on PPC32, this patch moves
all scaled cputing accounting logic into dedicated functions.
This patch doesn't change any functionality. It's only code
reorganisation.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
module_frob_arch_sections() is called before the module is moved to its
final location. The function descriptor section addresses we are setting
here are thus invalid. Fix this by processing opd section during
module_finalize()
Fixes: 5633e85b2c ("powerpc64: Add .opd based function descriptor dereference")
Cc: stable@vger.kernel.org # v4.16
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Like all other dma mapping drivers just return an error code instead
of an actual memory buffer. The reason for the overflow buffer was
that at the time swiotlb was invented there was no way to check for
dma mapping errors, but this has long been fixed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the recent commit 8b78fdb045 ("powerpc/time: Use
clockevents_register_device(), fixing an issue with large
decrementer") we changed the way we initialise the decrementer
clockevent(s).
We no longer initialise the mult & shift values of
decrementer_clockevent itself.
This has the effect of breaking PR KVM, because it uses those values
in kvmppc_emulate_dec(). The symptom is guest kernels spin forever
mid-way through boot.
For now fix it by assigning back to decrementer_clockevent the mult
and shift values.
Fixes: 8b78fdb045 ("powerpc/time: Use clockevents_register_device(), fixing an issue with large decrementer")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Back when I added -Werror in commit ba55bd7436 ("powerpc: Add
configurable -Werror for arch/powerpc") I did it by adding it to most
of the arch Makefiles.
At the time we excluded math-emu, because apparently it didn't build
cleanly. But that seems to have been fixed somewhere in the interim.
So move the -Werror addition to the top-level of the arch, this saves
us from repeating it in every Makefile and means we won't forget to
add it to any new sub-dirs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
do_exit() already includes a test to panic() is in_interrupt()
This patch removes powerpc one which is redundant.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When creating the boot-time FDT from an actual Open Firmware live
tree, let's generate "phandle" properties for the phandles instead
of the old deprecated "linux,phandle".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Unsplit warning printf()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
prom_init.c must not modify the kernel image outside
of the .bss.prominit section. Thus make sure that
prom_init.o doesn't have anything in any of these:
.data
.bss
.init.data
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This makes __prombss its own section, and for now store
it in .bss.
This will give us the ability later to store it elsewhere
and/or free it after boot (it's about 8KB).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As they are no longer used past the end of prom_init
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make the existing initialized definition constant and copy
it to a __prombss copy
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Initialize it dynamically instead of statically
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We removed support for running under any OPAL version
earlier than v3 in 2015 (they never saw the light of day
anyway), but we kept some leftovers of this support in
prom_init.c, so let's take it out.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This replaces all occurrences of __initdata for uninitialized
data with a new __prombss
Currently __promdata is defined to be __initdata but we'll
eventually change that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch implements support for discovering storage class memory
devices at boot and for handling hotplug of new regions via RTAS
hotplug events.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Fix CONFIG_MEMORY_HOTPLUG=n build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When printing the machine check cause, the cause appears on the
following line due to bad use of printk without \n:
[ 33.663993] Machine check in kernel mode.
[ 33.664011] Caused by (from SRR1=9032):
[ 33.664036] Data access error at address c90c8000
This patch fixes it by using pr_cont() for the second part:
[ 133.258131] Machine check in kernel mode.
[ 133.258146] Caused by (from SRR1=9032): Data access error at address c90c8000
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
slb_flush_and_rebolt() is misleading, it is called in virtual mode, so
it can not possibly change the stack, so it should not be touching the
shadow area. And since vmalloc is no longer bolted, it should not
change any bolted mappings at all.
Change the name to slb_flush_and_restore_bolted(), and have it just
load the kernel stack from what's currently in the shadow SLB area.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When switching processes, currently all user SLBEs are cleared, and a
few (exec_base, pc, and stack) are preloaded. In trivial testing with
small apps, this tends to miss the heap and low 256MB segments, and it
will also miss commonly accessed segments on large memory workloads.
Add a simple round-robin preload cache that just inserts the last SLB
miss into the head of the cache and preloads those at context switch
time. Every 256 context switches, the oldest entry is removed from the
cache to shrink the cache and require fewer slbmte if they are unused.
Much more could go into this, including into the SLB entry reclaim
side to track some LRU information etc, which would require a study of
large memory workloads. But this is a simple thing we can do now that
is an obvious win for common workloads.
With the full series, process switching speed on the context_switch
benchmark on POWER9/hash (with kernel speculation security masures
disabled) increases from 140K/s to 178K/s (27%).
POWER8 does not change much (within 1%), it's unclear why it does not
see a big gain like POWER9.
Booting to busybox init with 256MB segments has SLB misses go down
from 945 to 69, and with 1T segments 900 to 21. These could almost all
be eliminated by preloading a bit more carefully with ELF binary
loading.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This will be used by the SLB code in the next patch, but for now this
sets the slb_addr_limit to the correct size for 32-bit tasks.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add 32-entry bitmaps to track the allocation status of the first 32
SLB entries, and whether they are user or kernel entries. These are
used to allocate free SLB entries first, before resorting to the round
robin allocator.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch moves SLB miss handlers completely to C, using the standard
exception handler macros to set up the stack and branch to C.
This can be done because the segment containing the kernel stack is
always bolted, so accessing it with relocation on will not cause an
SLB exception.
Arbitrary kernel memory must not be accessed when handling kernel
space SLB misses, so care should be taken there. However user SLB
misses can access any kernel memory, which can be used to move some
fields out of the paca (in later patches).
User SLB misses could quite easily reconcile IRQs and set up a first
class kernel environment and exit via ret_from_except, however that
doesn't seem to be necessary at the moment, so we only do that if a
bad fault is encountered.
[ Credit to Aneesh for bug fixes, error checks, and improvements to
bad address handling, etc ]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Disallow tracing for all of slb.c for now.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PPR is the odd register out when it comes to interrupt handling, it is
saved in current->thread.ppr while all others are saved on the stack.
The difficulty with this is that accessing thread.ppr can cause a SLB
fault, but the SLB fault handler implementation in C change had
assumed the normal exception entry handlers would not cause an SLB
fault.
Fix this by allocating room in the interrupt stack to save PPR.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we've split the user & kernel versions of pt_regs we need to
be more careful in the ptrace code.
For now we've ensured the location of the fields in both structs is
the same, so most of the ptrace code doesn't need updating.
But there are a few places where we use sizeof(pt_regs), and these
will be wrong as soon as we increase the size of the kernel structure.
So flip them all to use sizeof(user_pt_regs).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We use a shared definition for struct pt_regs in uapi/asm/ptrace.h.
That means the layout of the structure is ABI, ie. we can't change it.
That would be fine if it was only used to describe the user-visible
register state of a process, but it's also the struct we use in the
kernel to describe the registers saved in an interrupt frame.
We'd like more flexibility in the content (and possibly layout) of the
kernel version of the struct, but currently that's not possible.
So split the definition into a user-visible definition which remains
unchanged, and a kernel internal one.
At the moment they're still identical, and we check that at build
time. That's because we have code (in ptrace etc.) that assumes that
they are the same. We will fix that code in future patches, and then
we can break the strict symmetry between the two structs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
_PAGE_PRIVILEGED corresponds to the SH bit which doesn't protect
against user access but only disables ASID verification on kernel
accesses. User access is controlled with _PMD_USER flag.
Name it _PAGE_SH instead of _PAGE_PRIVILEGED
_PAGE_HUGE corresponds to the SPS bit which doesn't really tells
that's it is a huge page but only that it is not a 4k page.
Name it _PAGE_SPS instead of _PAGE_HUGE
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to avoid multiple conversions, handover directly a
pgprot_t to map_kernel_page() as already done for radix.
Do the same for __ioremap_caller() and __ioremap_at().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Set PAGE_KERNEL directly in the caller and do not rely on a
hack adding PAGE_KERNEL flags when _PAGE_PRESENT is not set.
As already done for PPC64, use pgprot_cache() helpers instead of
_PAGE_XXX flags in PPC32 ioremap() derived functions.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In many places, ioremap_prot() and __ioremap() can be replaced with
higher level functions like ioremap(), ioremap_coherent(),
ioremap_cache(), ioremap_wc() ...
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Live Partition Migrations require all the present CPUs to execute the
H_JOIN call, and hence rtas_ibm_suspend_me() onlines any offline CPUs
before initiating the migration for this purpose.
The commit 85a88cabad
("powerpc/pseries: Disable CPU hotplug across migrations")
disables any CPU-hotplug operations once all the offline CPUs are
brought online to prevent any further state change. Once the
CPU-Hotplug operation is disabled, the code assumes that all the CPUs
are online.
However, there is a minor window in rtas_ibm_suspend_me() between
onlining the offline CPUs and disabling CPU-Hotplug when a concurrent
CPU-offline operations initiated by the userspace can succeed thereby
nullifying the the aformentioned assumption. In this unlikely case
these offlined CPUs will not call H_JOIN, resulting in a system hang.
Fix this by verifying that all the present CPUs are actually online
after CPU-Hotplug has been disabled, failing which we restore the
state of the offline CPUs in rtas_ibm_suspend_me() and return an
-EBUSY.
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently on POWER9 SMT8 cores systems, in sysfs, we report the
shared_cache_map for L1 caches (both data and instruction) to be the
cpu-ids of the threads in SMT8 cores. This is incorrect since on
POWER9 SMT8 cores there are two groups of threads, each of which
shares its own L1 cache.
This patch addresses this by reporting the shared_cpu_map correctly in
sysfs for L1 caches.
Before the patch
/sys/devices/system/cpu/cpu0/cache/index0/shared_cpu_map : 000000ff
/sys/devices/system/cpu/cpu0/cache/index1/shared_cpu_map : 000000ff
/sys/devices/system/cpu/cpu1/cache/index0/shared_cpu_map : 000000ff
/sys/devices/system/cpu/cpu1/cache/index1/shared_cpu_map : 000000ff
After the patch
/sys/devices/system/cpu/cpu0/cache/index0/shared_cpu_map : 00000055
/sys/devices/system/cpu/cpu0/cache/index1/shared_cpu_map : 00000055
/sys/devices/system/cpu/cpu1/cache/index0/shared_cpu_map : 000000aa
/sys/devices/system/cpu/cpu1/cache/index1/shared_cpu_map : 000000aa
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 SMT8 cores consist of two groups of threads, where threads in
each group shares L1-cache. The scheduler is not aware of this
distinction as the current sched-domain hierarchy has all the threads
of the core defined at the SMT domain.
SMT [Thread siblings of the SMT8 core]
DIE [CPUs in the same die]
NUMA [All the CPUs in the system]
Due to this, we can observe run-to-run variance when we run a
multi-threaded benchmark bound to a single core based on how the
scheduler spreads the software threads across the two groups in the
core.
We fix this in this patch by defining each group of threads which
share L1-cache to be the SMT level. The group of threads in the SMT8
core is defined to be the CACHE level. The sched-domain hierarchy
after this patch will be :
SMT [Thread siblings in the core that share L1 cache]
CACHE [Thread siblings that are in the SMT8 core]
DIE [CPUs in the same die]
NUMA [All the CPUs in the system]
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On IBM POWER9, the device tree exposes a property array identifed by
"ibm,thread-groups" which will indicate which groups of threads share
a particular set of resources.
As of today we only have one form of grouping identifying the group of
threads in the core that share the L1 cache, translation cache and
instruction data flow.
This patch adds helper functions to parse the contents of
"ibm,thread-groups" and populate a per-cpu variable to cache
information about siblings of each CPU that share the L1, traslation
cache and instruction data-flow.
It also defines a new global variable named "has_big_cores" which
indicates if the cores on this configuration have multiple groups of
threads that share L1 cache.
For each online CPU, it maintains a cpu_smallcore_mask, which
indicates the online siblings which share the L1-cache with it.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 6c1719942e ("powerpc/of: Remove useless register save/restore
when calling OF back") removed the saving of srr0 and srr1 when calling
into OpenFirmware. Commit e31aa453bb ("powerpc: Use LOAD_REG_IMMEDIATE
only for constants on 64-bit") did the same for rtas.
This means we don't need to save the extra stack space and can use
the common SWITCH_FRAME_SIZE.
There were already no users of _SRR0 and _SRR1 so we can remove them
too.
Link: https://github.com/linuxppc/linux/issues/83
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powerpc mobility code may receive RTAS requests to perform PRRN
(Platform Resource Reassignment Notification) topology changes at any
time, including during LPAR migration operations.
In some configurations where the affinity of CPUs or memory is being
changed on that platform, the PRRN requests may apply or refer to
outdated information prior to the complete update of the device-tree.
This patch changes the duration for which topology updates are
suppressed during LPAR migrations from just the rtas_ibm_suspend_me()
/ 'ibm,suspend-me' call(s) to cover the entire migration_store()
operation to allow all changes to the device-tree to be applied prior
to accepting and applying any PRRN requests.
For tracking purposes, pr_info notices are added to the functions
start_topology_update() and stop_topology_update() of 'numa.c'.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than mixing "if (state)" blocks and gotos, convert entirely to
"if (state)" blocks to make the state machine behaviour clearer.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The wait_state member of eeh_ops does not need to be platform
dependent; it's just logic around eeh_ops.get_state(). Therefore,
merge the two (slightly different!) platform versions into a new
function, eeh_wait_state() and remove the eeh_ops member.
While doing this, also correct:
* The wait logic, so that it never waits longer than max_wait.
* The wait logic, so that it never waits less than
EEH_STATE_MIN_WAIT_TIME.
* One call site where the result is treated like a bit field before
it's checked for negative error values.
* In pseries_eeh_get_state(), rename the "state" parameter to "delay"
because that's what it is.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, eeh_pe_state_mark() marks a PE (and it's children) with a
state and then performs additional processing if that state included
EEH_PE_ISOLATED.
The state parameter is always a constant at the call site, so
rearrange eeh_pe_state_mark() into two functions and just call the
appropriate one at each site.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pe_state_mark_with_cfg() just performs the work of
eeh_pe_state_mark() and then, conditionally, the work of
eeh_pe_state_clear(). However it is only ever called with a constant
state such that the condition is always true, so replace it by direct
calls.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the call to eeh_dev_to_pe() up, so that later it's clear that
"pe" isn't NULL.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change the name of the fields in eeh_rmv_data to clarify their usage.
Change "edev_list" to "removed_vf_list" because it does not contain
generic edevs, but rather only edevs that contain virtual functions
(which need to be removed during recovery).
Similarly, change "removed" to "removed_dev_count" because it is a
count of any removed devices, not just those in the above list.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instances of struct eeh_pe are placed in a tree structure using the
fields "child_list" and "child", so place these next to each other
in the definition.
The field "child" is a list entry, so remove the unnecessary and
misleading use of the list initializer, LIST_HEAD(), on it.
The eeh_dev struct contains two list entry fields, called "list" and
"rmv_list". Rename them to "entry" and "rmv_entry" and, as above, stop
initializing them with LIST_HEAD().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the unnecessary cast through void * on the first parameter and
remove the unused second parameter (always NULL).
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 'bus' member of struct eeh_dev is assigned to once but never used,
so remove it.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently a flag, EEH_POSTPONED_PROBE, is used to prevent an incorrect
message "EEH: No capable adapters found" from being displayed during
the boot of powernv systems.
It is necessary because, on powernv, the call to eeh_probe_devices()
made from eeh_init() is too early and EEH can't yet be enabled. A
second call is made later from eeh_pnv_post_init(), which succeeds.
(On pseries, the first call succeeds because PCI devices are set up
early enough and no second call is made.)
This can be simplified by moving the early call to eeh_probe_devices()
from eeh_init() (where it's seen by both platforms) to
pSeries_final_fixup(), so that each platform only calls
eeh_probe_devices() once, at a point where it can succeed.
This is slightly later in the boot sequence, but but still early
enough and it is now in the same place in the sequence for both
platforms (the pcibios_fixup hook).
The display of the message can be cleaned up as well, by moving it
into eeh_probe_devices().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_add_to_parent_pe() sometimes removes the EEH_PE_KEEP flag, but it
incorrectly removes it from pe->type, instead of pe->state.
However, rather than clearing it from the correct field, remove it.
Inspection of the code shows that it can't ever have had any effect
(even if it had been cleared from the correct field), because the
field is never tested after it is cleared by the statement in
question.
The clear statement was added by commit 807a827d4e ("powerpc/eeh:
Keep PE during hotplug"), but it didn't explain why it was necessary.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a device is removed during EEH processing (either by a driver's
handler or as part of recovery), it can lead to a null dereference
in eeh_pe_report_edev().
To handle this, skip devices that have been removed.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If an error occurs during an unplug operation, it's possible for
eeh_dump_dev_log() to be called when edev->pdn is null, which
currently leads to dereferencing a null pointer.
Handle this by skipping the error log for those devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently when we get an unknown RTAS event it prints the type as
"Unknown" and no other useful information. Add the raw type code to the
log message so that we have something to work off.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powerpc kernel uses setjmp which causes a warning when building
with clang:
In file included from arch/powerpc/xmon/xmon.c:51:
./arch/powerpc/include/asm/setjmp.h:15:13: error: declaration of
built-in function 'setjmp' requires inclusion of the header <setjmp.h>
[-Werror,-Wbuiltin-requires-header]
extern long setjmp(long *);
^
./arch/powerpc/include/asm/setjmp.h:16:13: error: declaration of
built-in function 'longjmp' requires inclusion of the header <setjmp.h>
[-Werror,-Wbuiltin-requires-header]
extern void longjmp(long *, long);
^
This *is* the header and we're not using the built-in setjump but
rather the one in arch/powerpc/kernel/misc.S. As the compiler warning
does not make sense, it for the files where setjmp is used.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
[mpe: Move subdir-ccflags in xmon/Makefile to not clobber -Werror]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
instructions_to_print var is assigned value 16 and there is no
way to change it.
This patch replaces it by a constant.
Reviewed-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When two processes crash at the same time, we sometimes encounter
interleaving in the middle of a line:
init[1]: segfault (11) at 0 nip 0 lr 0 code 1
init[1]: code: XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
init[74]: segfault (11) at 10a74 nip 1000c198 lr 100078c8 code 1 in sh[10000000+14000]
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
init[1]: code: XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
init[74]: code: 90010024 bf61000c 91490a7c 3fa01002 3be00000 7d3e4b78 3bbd0c20 3b600000
init[74]: code: 3b9d0040 7c7fe02e 2f830000 419e0028 <89230000> 2f890000 41be001c 4b7f6e79
This patch fixes it by preparing complete lines in a buffer and
printing it at once.
Fixes: 88b0fe1757 ("powerpc: Add show_user_instructions()")
Reviewed-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Use seq_buf_printf() not seq_buf_puts() which doesn't NULL terminate]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As spotted by sparse:
arch/powerpc/kernel/process.c:1302:6: warning: symbol 'show_user_instructions' was not declared. Should it be static?
Fixes: 88b0fe1757 ("powerpc: Add show_user_instructions()")
Reviewed-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes the following warnings, which are leftovers
from when __get_user() was replaced by probe_kernel_address().
arch/powerpc/kernel/process.c:1287:22: warning: incorrect type in argument 2 (different address spaces)
arch/powerpc/kernel/process.c:1287:22: expected void const *src
arch/powerpc/kernel/process.c:1287:22: got unsigned int [noderef] <asn:1>*<noident>
arch/powerpc/kernel/process.c:1319:21: warning: incorrect type in argument 2 (different address spaces)
arch/powerpc/kernel/process.c:1319:21: expected void const *src
arch/powerpc/kernel/process.c:1319:21: got unsigned int [noderef] <asn:1>*<noident>
Fixes: 7b051f665c ("powerpc: Use probe_kernel_address in show_instructions")
Reviewed-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the struct lsm_info table is not an initcall, we can just move it
into INIT_DATA like all the other tables.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Casey Schaufler <casey@schaufler-ca.com>
Reviewed-by: John Johansen <john.johansen@canonical.com>
Reviewed-by: James Morris <james.morris@microsoft.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
This adds a new hypercall, H_ENTER_NESTED, which is used by a nested
hypervisor to enter one of its nested guests. The hypercall supplies
register values in two structs. Those values are copied by the level 0
(L0) hypervisor (the one which is running in hypervisor mode) into the
vcpu struct of the L1 guest, and then the guest is run until an
interrupt or error occurs which needs to be reported to L1 via the
hypercall return value.
Currently this assumes that the L0 and L1 hypervisors are the same
endianness, and the structs passed as arguments are in native
endianness. If they are of different endianness, the version number
check will fail and the hcall will be rejected.
Nested hypervisors do not support indep_threads_mode=N, so this adds
code to print a warning message if the administrator has set
indep_threads_mode=N, and treat it as Y.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the 'regs' field was added to struct kvm_vcpu_arch, the code
was changed to use several of the fields inside regs (e.g., gpr, lr,
etc.) but not the ccr field, because the ccr field in struct pt_regs
is 64 bits on 64-bit platforms, but the cr field in kvm_vcpu_arch is
only 32 bits. This changes the code to use the regs.ccr field
instead of cr, and changes the assembly code on 64-bit platforms to
use 64-bit loads and stores instead of 32-bit ones.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When doing nested virtualization, it is only necessary to do the
transactional memory hypervisor assist at level 0, that is, when
we are in hypervisor mode. Nested hypervisors can just use the TM
facilities as architected. Therefore we should clear the
CPU_FTR_P9_TM_HV_ASSIST bit when we are not in hypervisor mode,
along with the CPU_FTR_HVMODE bit.
Doing this will not change anything at this stage because the only
code that tests CPU_FTR_P9_TM_HV_ASSIST is in HV KVM, which currently
can only be used when when CPU_FTR_HVMODE is set.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Four regression fixes.
A fix for a change to lib/xz which broke our zImage loader when building with XZ
compression. OK'ed by Herbert who merged the original patch.
The recent fix we did to avoid patching __init text broke some 32-bit machines,
fix that.
Our show_user_instructions() could be tricked into printing kernel memory, add a
check to avoid that.
And a fix for a change to our NUMA initialisation logic, which causes crashes in
some kdump configurations.
Thanks to:
Christophe Leroy, Hari Bathini, Jann Horn, Joel Stanley, Meelis Roos, Murilo
Opsfelder Araujo, Srikar Dronamraju.
-----BEGIN PGP SIGNATURE-----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=FxNJ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-4' of https://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Michael writes:
"powerpc fixes for 4.19 #4
Four regression fixes.
A fix for a change to lib/xz which broke our zImage loader when
building with XZ compression. OK'ed by Herbert who merged the
original patch.
The recent fix we did to avoid patching __init text broke some 32-bit
machines, fix that.
Our show_user_instructions() could be tricked into printing kernel
memory, add a check to avoid that.
And a fix for a change to our NUMA initialisation logic, which causes
crashes in some kdump configurations.
Thanks to:
Christophe Leroy, Hari Bathini, Jann Horn, Joel Stanley, Meelis
Roos, Murilo Opsfelder Araujo, Srikar Dronamraju."
* tag 'powerpc-4.19-4' of https://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/numa: Skip onlining a offline node in kdump path
powerpc: Don't print kernel instructions in show_user_instructions()
powerpc/lib: fix book3s/32 boot failure due to code patching
lib/xz: Put CRC32_POLY_LE in xz_private.h
Recently we implemented show_user_instructions() which dumps the code
around the NIP when a user space process dies with an unhandled
signal. This was modelled on the x86 code, and we even went so far as
to implement the exact same bug, namely that if the user process
crashed with its NIP pointing into the kernel we will dump kernel text
to dmesg. eg:
bad-bctr[2996]: segfault (11) at c000000000010000 nip c000000000010000 lr 12d0b0894 code 1
bad-bctr[2996]: code: fbe10068 7cbe2b78 7c7f1b78 fb610048 38a10028 38810020 fb810050 7f8802a6
bad-bctr[2996]: code: 3860001c f8010080 48242371 60000000 <7c7b1b79> 4082002c e8010080 eb610048
This was discovered on x86 by Jann Horn and fixed in commit
342db04ae7 ("x86/dumpstack: Don't dump kernel memory based on usermode RIP").
Fix it by checking the adjusted NIP value (pc) and number of
instructions against USER_DS, and bail if we fail the check, eg:
bad-bctr[2969]: segfault (11) at c000000000010000 nip c000000000010000 lr 107930894 code 1
bad-bctr[2969]: Bad NIP, not dumping instructions.
Fixes: 88b0fe1757 ("powerpc: Add show_user_instructions()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PPC_INVALIDATE_ERAT is slbia IH=7 which is a new variant introduced
with POWER9, and the result is undefined on earlier CPUs.
Commits 7b9f71f974 ("powerpc/64s: POWER9 machine check handler") and
d4748276ae ("powerpc/64s: Improve local TLB flush for boot and MCE on
POWER9") caused POWER7/8 code to use this instruction. Remove it. An
ERAT flush can be made by invalidatig the SLB, but before POWER9 that
requires a flush and rebolt.
Fixes: 7b9f71f974 ("powerpc/64s: POWER9 machine check handler")
Fixes: d4748276ae ("powerpc/64s: Improve local TLB flush for boot and MCE on POWER9")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If CONFIG_PPC_WATCHDOG is enabled we always cap the decrementer to
0x7fffffff:
if (IS_ENABLED(CONFIG_PPC_WATCHDOG))
set_dec(0x7fffffff);
else
set_dec(decrementer_max);
If there are no future events, we don't reprogram the decrementer
after this and we end up with 0x7fffffff even on a large decrementer
capable system.
As suggested by Nick, add a set_state_oneshot_stopped callback
so we program the decrementer with decrementer_max if there are
no future events.
Signed-off-by: Anton Blanchard <anton@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We currently cap the decrementer clockevent at 4 seconds, even on systems
with large decrementer support. Fix this by converting the code to use
clockevents_register_device() which calculates the upper bound based on
the max_delta passed in.
Signed-off-by: Anton Blanchard <anton@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add call to early_memtest() so that kernel compiled with
CONFIG_MEMTEST really perform memtest at startup when requested
via 'memtest' boot parameter.
Tested-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The comments in this file don't conform to the coding style so take
them to "Comment Formatting Re-Education Camp".
Suggested-by: Michael "Camp Drill Sergeant" Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Reflow some comments and add full stops, fix spelling of Sergeant.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The code in machine_check_exception excludes 64s hvmode when
incrementing the MCE counter only to call opal_machine_check to
increment it specifically for this case.
Remove the exclusion and special case.
Fixes: a43c159042 ("powerpc/pseries: Flush SLB contents on SLB MCE
errors.")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On a kernel TM Bad thing program exception, the Machine State Register
(MSR) is not being properly displayed. The exception code dumps a 32-bits
value but MSR is a 64 bits register for all platforms that have HTM
enabled.
This patch dumps the MSR value as a 64-bits value instead of 32 bits. In
order to do so, the 'reason' variable could not be used, since it trimmed
MSR to 32-bits (int).
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently msr_tm_active() is a wrapper around MSR_TM_ACTIVE() if
CONFIG_PPC_TRANSACTIONAL_MEM is set, or it is just a function that
returns false if CONFIG_PPC_TRANSACTIONAL_MEM is not set.
This function is not necessary, since MSR_TM_ACTIVE() just do the same and
could be used, removing the dualism and simplifying the code.
This patchset remove every instance of msr_tm_active() and replaced it
by MSR_TM_ACTIVE().
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is a patch that adds support for PTRACE_SYSEMU ptrace request in
PowerPC architecture.
When ptrace(PTRACE_SYSEMU, ...) request is called, it will be handled by
the arch independent function ptrace_resume(), which will tag the task with
the TIF_SYSCALL_EMU flag. This flag needs to be handled from a platform
dependent point of view, which is what this patch does.
This patch adds this task's flag as part of the _TIF_SYSCALL_DOTRACE, which
is the MACRO that is used to trace syscalls at entrance/exit.
Since TIF_SYSCALL_EMU is now part of _TIF_SYSCALL_DOTRACE, if the task has
_TIF_SYSCALL_DOTRACE set, it will hit do_syscall_trace_enter() at syscall
entrance and do_syscall_trace_leave() at syscall leave.
do_syscall_trace_enter() needs to handle the TIF_SYSCALL_EMU flag properly,
which will interrupt the syscall executing if TIF_SYSCALL_EMU is set. The
output values should not be changed, i.e. the return value (r3) should
contain the original syscall argument on exit.
With this flag set, the syscall is not executed fundamentally, because
do_syscall_trace_enter() is returning -1 which is bigger than NR_syscall,
thus, skipping the syscall execution and exiting userspace.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Moving TIF_32BIT to use bit 20 instead of 4 in the task flag field.
This change is making room for an upcoming new task macro
(_TIF_SYSCALL_EMU) which is preferred to set a bit in the lower 16-bits
part of the word.
This upcoming flag macro will take part in a composed macro
(_TIF_SYSCALL_DOTRACE) which will contain other flags as well, and it is
preferred that the whole _TIF_SYSCALL_DOTRACE macro only sets the lower 16
bits of a word, so, it could be handled using immediate operations (as load
immediate, add immediate, ...) where the immediate operand (SI) is limited
to 16-bits.
Another possible solution would be using the LOAD_REG_IMMEDIATE() macro
to load a full 64-bits word immediate, but it takes 5 operations instead of
one.
Having TIF_32BITS being redefined to use an upper bit is not a problem
since there is only one place in the assembly code where TIF_32BIT is being
used, and it could be replaced with an operation with right shift (addis),
since it is used alone, i.e. not being part of a composed macro, which has
different bits set, and would require LOAD_REG_IMMEDIATE().
Tested on a 64 bits Big Endian machine running a 32 bits task.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PPC64, as register r13 points to the paca_struct at all time,
this patch adds a copy of the canary there, which is copied at
task_switch.
That new canary is then used by using the following GCC options:
-mstack-protector-guard=tls
-mstack-protector-guard-reg=r13
-mstack-protector-guard-offset=offsetof(struct paca_struct, canary))
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This functionality was tentatively added in the past
(commit 6533b7c16e ("powerpc: Initial stack protector
(-fstack-protector) support")) but had to be reverted
(commit f2574030b0 ("powerpc: Revert the initial stack
protector support") because of GCC implementing it differently
whether it had been built with libc support or not.
Now, GCC offers the possibility to manually set the
stack-protector mode (global or tls) regardless of libc support.
This time, the patch selects HAVE_STACKPROTECTOR only if
-mstack-protector-guard=tls is supported by GCC.
On PPC32, as register r2 points to current task_struct at
all time, the stack_canary located inside task_struct can be
used directly by using the following GCC options:
-mstack-protector-guard=tls
-mstack-protector-guard-reg=r2
-mstack-protector-guard-offset=offsetof(struct task_struct, stack_canary))
The protector is disabled for prom_init and bootx_init as
it is too early to handle it properly.
$ echo CORRUPT_STACK > /sys/kernel/debug/provoke-crash/DIRECT
[ 134.943666] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: lkdtm_CORRUPT_STACK+0x64/0x64
[ 134.943666]
[ 134.955414] CPU: 0 PID: 283 Comm: sh Not tainted 4.18.0-s3k-dev-12143-ga3272be41209 #835
[ 134.963380] Call Trace:
[ 134.965860] [c6615d60] [c001f76c] panic+0x118/0x260 (unreliable)
[ 134.971775] [c6615dc0] [c001f654] panic+0x0/0x260
[ 134.976435] [c6615dd0] [c032c368] lkdtm_CORRUPT_STACK_STRONG+0x0/0x64
[ 134.982769] [c6615e00] [ffffffff] 0xffffffff
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PPC32 uses nonrecoverable_exception() while PPC64 uses
unrecoverable_exception().
Both functions are doing almost the same thing.
This patch removes nonrecoverable_exception()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commits:
5e46e29e6a ("powerpc/64s/hash: convert SLB miss handlers to C")
8fed04d0f6 ("powerpc/64s/hash: remove user SLB data from the paca")
655deecf67 ("powerpc/64s/hash: SLB allocation status bitmaps")
2e1626744e ("powerpc/64s/hash: provide arch_setup_exec hooks for hash slice setup")
89ca4e126a ("powerpc/64s/hash: Add a SLB preload cache")
This series had a few bugs, and the fixes are not all trivial. So
revert most of it for now.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A reasonably big batch of fixes due to me being away for a few weeks.
A fix for the TM emulation support on Power9, which could result in corrupting
the guest r11 when running under KVM.
Two fixes to the TM code which could lead to userspace GPR corruption if we take
an SLB miss at exactly the wrong time.
Our dynamic patching code had a bug that meant we could patch freed __init text,
which could lead to corrupting userspace memory.
csum_ipv6_magic() didn't work on little endian platforms since we optimised it
recently.
A fix for an endian bug when reading a device tree property telling us how many
storage keys the machine has available.
Fix a crash seen on some configurations of PowerVM when migrating the partition
from one machine to another.
A fix for a regression in the setup of our CPU to NUMA node mapping in KVM
guests.
A fix to our selftest Makefiles to make them work since a recent change to the
shared Makefile logic.
Thanks to:
Alexey Kardashevskiy, Breno Leitao, Christophe Leroy, Michael Bringmann,
Michael Neuling, Nicholas Piggin, Paul Mackerras,, Srikar Dronamraju, Thiago
Jung Bauermann, Xin Long.
-----BEGIN PGP SIGNATURE-----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=G6wq
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-3' of https://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Michael writes:
"powerpc fixes for 4.19 #3
A reasonably big batch of fixes due to me being away for a few weeks.
A fix for the TM emulation support on Power9, which could result in
corrupting the guest r11 when running under KVM.
Two fixes to the TM code which could lead to userspace GPR corruption
if we take an SLB miss at exactly the wrong time.
Our dynamic patching code had a bug that meant we could patch freed
__init text, which could lead to corrupting userspace memory.
csum_ipv6_magic() didn't work on little endian platforms since we
optimised it recently.
A fix for an endian bug when reading a device tree property telling
us how many storage keys the machine has available.
Fix a crash seen on some configurations of PowerVM when migrating the
partition from one machine to another.
A fix for a regression in the setup of our CPU to NUMA node mapping
in KVM guests.
A fix to our selftest Makefiles to make them work since a recent
change to the shared Makefile logic."
* tag 'powerpc-4.19-3' of https://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix Makefiles for headers_install change
powerpc/numa: Use associativity if VPHN hcall is successful
powerpc/tm: Avoid possible userspace r1 corruption on reclaim
powerpc/tm: Fix userspace r13 corruption
powerpc/pseries: Fix unitialized timer reset on migration
powerpc/pkeys: Fix reading of ibm, processor-storage-keys property
powerpc: fix csum_ipv6_magic() on little endian platforms
powerpc/powernv/ioda2: Reduce upper limit for DMA window size (again)
powerpc: Avoid code patching freed init sections
KVM: PPC: Book3S HV: Fix guest r11 corruption with POWER9 TM workarounds
Current we store the userspace r1 to PACATMSCRATCH before finally
saving it to the thread struct.
In theory an exception could be taken here (like a machine check or
SLB miss) that could write PACATMSCRATCH and hence corrupt the
userspace r1. The SLB fault currently doesn't touch PACATMSCRATCH, but
others do.
We've never actually seen this happen but it's theoretically
possible. Either way, the code is fragile as it is.
This patch saves r1 to the kernel stack (which can't fault) before we
turn MSR[RI] back on. PACATMSCRATCH is still used but only with
MSR[RI] off. We then copy r1 from the kernel stack to the thread
struct once we have MSR[RI] back on.
Suggested-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we treclaim we store the userspace checkpointed r13 to a scratch
SPR and then later save the scratch SPR to the user thread struct.
Unfortunately, this doesn't work as accessing the user thread struct
can take an SLB fault and the SLB fault handler will write the same
scratch SPRG that now contains the userspace r13.
To fix this, we store r13 to the kernel stack (which can't fault)
before we access the user thread struct.
Found by running P8 guest + powervm + disable_1tb_segments + TM. Seen
as a random userspace segfault with r13 looking like a kernel address.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Call force_sig_pkuerr directly instead of rolling it by hand
in _exception_pkey.
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Now that _exception no longer calls _exception_pkey it is no longer
necessary to handle any signal with any si_code. All pkey exceptions
are SIGSEGV with paired with SEGV_PKUERR. So just handle
that case and remove the now unnecessary parameters from _exception_pkey.
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The callers of _exception don't need the pkey exception logic because
they are not processing a pkey exception. So just call exception_common
directly and then call force_sig_fault to generate the appropriate siginfo
and deliver the appropriate signal.
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
It is brittle and wrong to populate si_pkey when there was not a pkey
exception. The field does not exist for all si_codes and in some
cases another field exists in the same memory location.
So factor out the code that all exceptions handlers must run
into exception_common, leaving the individual exception handlers
to generate the signals themselves.
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace user_single_step_siginfo with user_single_step_report
that allocates siginfo structure on the stack and sends it.
This allows tracehook_report_syscall_exit to become a simple
if statement that calls user_single_step_report or ptrace_report_syscall
depending on the value of step.
Update the default helper function now called user_single_step_report
to explicitly set si_code to SI_USER and to set si_uid and si_pid to 0.
The default helper has always been doing this (using memset) but it
was far from obvious.
The powerpc helper can now just call force_sig_fault.
The x86 helper can now just call send_sigtrap.
Unfortunately the default implementation of user_single_step_report
can not use force_sig_fault as it does not use a SIGTRAP si_code.
So it has to carefully setup the siginfo and use use force_sig_info.
The net result is code that is easier to understand and simpler
to maintain.
Ref: 85ec7fd9f8 ("ptrace: introduce user_single_step_siginfo() helper")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Firmware-Assisted Dump (FADump) needs to be registered again after any
memory hot add/remove operation to update the crash memory ranges. But
currently, the kernel returns '-EEXIST' if we try to register without
uregistering it first. This could expose the system to racing issues
while unregistering and registering FADump from userspace during udev
events. Spare the userspace of this and let it be taken care of in the
kernel space for a simpler interface.
Since this change, running 'echo 1 > /sys/kernel/fadump_registered'
would result in re-regisering (unregistering and registering) FADump,
if it was already registered.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Acked-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In prom_check_platform_support() we retrieve and parse the
"ibm,arch-vec-5-platform-support" property of the chosen node.
Currently we use a variable length array however to avoid this use an
array of constant length 8.
This property is used to indicate the supported options of vector 5
bytes 23-26 of the ibm,architecture.vec node. Each of these options
is a pair of bytes, thus for 4 options we have a max length of 8 bytes.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When performing partition migrations all present CPUs must be online
as all present CPUs must make the H_JOIN call as part of the migration
process. Once all present CPUs make the H_JOIN call, one CPU is returned
to make the rtas call to perform the migration to the destination system.
During testing of migration and changing the SMT state we have found
instances where CPUs are offlined, as part of the SMT state change,
before they make the H_JOIN call. This results in a hung system where
every CPU is either in H_JOIN or offline.
To prevent this this patch disables CPU hotplug during the migration
process.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When switching processes, currently all user SLBEs are cleared, and a
few (exec_base, pc, and stack) are preloaded. In trivial testing with
small apps, this tends to miss the heap and low 256MB segments, and it
will also miss commonly accessed segments on large memory workloads.
Add a simple round-robin preload cache that just inserts the last SLB
miss into the head of the cache and preloads those at context switch
time. Every 256 context switches, the oldest entry is removed from the
cache to shrink the cache and require fewer slbmte if they are unused.
Much more could go into this, including into the SLB entry reclaim
side to track some LRU information etc, which would require a study of
large memory workloads. But this is a simple thing we can do now that
is an obvious win for common workloads.
With the full series, process switching speed on the context_switch
benchmark on POWER9/hash (with kernel speculation security masures
disabled) increases from 140K/s to 178K/s (27%).
POWER8 does not change much (within 1%), it's unclear why it does not
see a big gain like POWER9.
Booting to busybox init with 256MB segments has SLB misses go down
from 945 to 69, and with 1T segments 900 to 21. These could almost all
be eliminated by preloading a bit more carefully with ELF binary
loading.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This will be used by the SLB code in the next patch, but for now this
sets the slb_addr_limit to the correct size for 32-bit tasks.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add 32-entry bitmaps to track the allocation status of the first 32
SLB entries, and whether they are user or kernel entries. These are
used to allocate free SLB entries first, before resorting to the round
robin allocator.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
User SLB mappig data is copied into the PACA from the mm->context so
it can be accessed by the SLB miss handlers.
After the C conversion, SLB miss handlers now run with relocation on,
and user SLB misses are able to take recursive kernel SLB misses, so
the user SLB mapping data can be removed from the paca and accessed
directly.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch moves SLB miss handlers completely to C, using the standard
exception handler macros to set up the stack and branch to C.
This can be done because the segment containing the kernel stack is
always bolted, so accessing it with relocation on will not cause an
SLB exception.
Arbitrary kernel memory may not be accessed when handling kernel space
SLB misses, so care should be taken there. However user SLB misses can
access any kernel memory, which can be used to move some fields out of
the paca (in later patches).
User SLB misses could quite easily reconcile IRQs and set up a first
class kernel environment and exit via ret_from_except, however that
doesn't seem to be necessary at the moment, so we only do that if a
bad fault is encountered.
[ Credit to Aneesh for bug fixes, error checks, and improvements to bad
address handling, etc ]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Since RFC:
- Added MSR[RI] handling
- Fixed up a register loss bug exposed by irq tracing (Aneesh)
- Reject misses outside the defined kernel regions (Aneesh)
- Added several more sanity checks and error handling (Aneesh), we may
look at consolidating these tests and tightenig up the code but for
a first pass we decided it's better to check carefully.
Since v1:
- Fixed SLB cache corruption (Aneesh)
- Fixed untidy SLBE allocation "leak" in get_vsid error case
- Now survives some stress testing on real hardware
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I only have POWER8/9 to test, so just remove it for those.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that other platforms also implements real mode mce handler,
lets consolidate the code by sharing existing powernv machine check
early code. Rename machine_check_powernv_early to
machine_check_common_early and reuse the code.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On pseries, as of today system crashes if we get a machine check
exceptions due to SLB errors. These are soft errors and can be fixed
by flushing the SLBs so the kernel can continue to function instead of
system crash. We do this in real mode before turning on MMU. Otherwise
we would run into nested machine checks. This patch now fetches the
rtas error log in real mode and flushes the SLBs on SLB/ERAT errors.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michal Suchanek <msuchanek@suse.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The tbl pointer is being derefenced by IOMMU_PAGE_SIZE prior the check
if it is not NULL.
Just moving the dereference code to after the check, where there will
be guarantee that 'tbl' will not be NULL.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch simply fix part of the documentation on the HTM code.
This fixes reference to old fields that were renamed in commit
000ec280e3 ("powerpc: tm: Rename transct_(*) to ck(\1)_state")
It also documents better the flow after commit eb5c3f1c86 ("powerpc:
Always save/restore checkpointed regs during treclaim/trecheckpoint"),
where tm_recheckpoint can recheckpoint what is in ck{fp,vr}_state
blindly.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we come into the softpatch handler (0x1500), we use r11 to store
the HSRR0 for later use by the denorm handler.
We also use the softpatch handler for the TM workarounds for
POWER9. Unfortunately, in kvmppc_interrupt_hv we later store r11 out
to the vcpu assuming it's still what we got from userspace.
This causes r11 to be corrupted in the VCPU and hence when we restore
the guest, we get a corrupted r11. We've seen this when running TM
tests inside guests on P9.
This fixes the problem by only touching r11 in the denorm case.
Fixes: 4bb3c7a020 ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Cc: <stable@vger.kernel.org> # 4.17+
Test-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Call Frame Information is used by gdb for back-traces and inserting
breakpoints on function return for the "finish" command. This failed
when inside __kernel_clock_gettime. More concerning than difficulty
debugging is that CFI is also used by stack frame unwinding code to
implement exceptions. If you have an app that needs to handle
asynchronous exceptions for some reason, and you are unlucky enough to
get one inside the VDSO time functions, your app will crash.
What's wrong: There is control flow in __kernel_clock_gettime that
reaches label 99 without saving lr in r12. CFI info however is
interpreted by the unwinder without reference to control flow: It's a
simple matter of "Execute all the CFI opcodes up to the current
address". That means the unwinder thinks r12 contains the return
address at label 99. Disabuse it of that notion by resetting CFI for
the return address at label 99.
Note that the ".cfi_restore lr" could have gone anywhere from the
"mtlr r12" a few instructions earlier to the instruction at label 99.
I put the CFI as late as possible, because in general that's best
practice (and if possible grouped with other CFI in order to reduce
the number of CFI opcodes executed when unwinding). Using r12 as the
return address is perfectly fine after the "mtlr r12" since r12 on
that code path still contains the return address.
__get_datapage also has a CFI error. That function temporarily saves
lr in r0, and reflects that fact with ".cfi_register lr,r0". A later
use of r0 means the CFI at that point isn't correct, as r0 no longer
contains the return address. Fix that too.
Signed-off-by: Alan Modra <amodra@gmail.com>
Tested-by: Reza Arbab <arbab@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently on P9N DD2.1 we end up taking infinite TM facility
unavailable exceptions on the first TM usage by userspace.
In the special case of TM no suspend (P9N DD2.1), Linux is told TM is
off via CPU dt-ftrs but told to (partially) use it via
OPAL_REINIT_CPUS_TM_SUSPEND_DISABLED. So HFSCR[TM] will be off from
dt-ftrs but we need to turn it on for the no suspend case.
This patch fixes this by enabling HFSCR TM in this case.
Cc: stable@vger.kernel.org # 4.15+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
At the moment the real mode handler of H_PUT_TCE calls iommu_tce_xchg_rm()
which in turn reads the old TCE and if it was a valid entry, marks
the physical page dirty if it was mapped for writing. Since it is in
real mode, realmode_pfn_to_page() is used instead of pfn_to_page()
to get the page struct. However SetPageDirty() itself reads the compound
page head and returns a virtual address for the head page struct and
setting dirty bit for that kills the system.
This adds additional dirty bit tracking into the MM/IOMMU API for use
in the real mode. Note that this does not change how VFIO and
KVM (in virtual mode) set this bit. The KVM (real mode) changes include:
- use the lowest bit of the cached host phys address to carry
the dirty bit;
- mark pages dirty when they are unpinned which happens when
the preregistered memory is released which always happens in virtual
mode;
- add mm_iommu_ua_mark_dirty_rm() helper to set delayed dirty bit;
- change iommu_tce_xchg_rm() to take the kvm struct for the mm to use
in the new mm_iommu_ua_mark_dirty_rm() helper;
- move iommu_tce_xchg_rm() to book3s_64_vio_hv.c (which is the only
caller anyway) to reduce the real mode KVM and IOMMU knowledge
across different subsystems.
This removes realmode_pfn_to_page() as it is not used anymore.
While we at it, remove some EXPORT_SYMBOL_GPL() as that code is for
the real mode only and modules cannot call it anyway.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Christoph Hellwig suggested a slightly different path for handling
backwards compatibility with the 32-bit time_t based system calls:
Rather than simply reusing the compat_sys_* entry points on 32-bit
architectures unchanged, we get rid of those entry points and the
compat_time types by renaming them to something that makes more sense
on 32-bit architectures (which don't have a compat mode otherwise),
and then share the entry points under the new name with the 64-bit
architectures that use them for implementing the compatibility.
The following types and interfaces are renamed here, and moved
from linux/compat_time.h to linux/time32.h:
old new
--- ---
compat_time_t old_time32_t
struct compat_timeval struct old_timeval32
struct compat_timespec struct old_timespec32
struct compat_itimerspec struct old_itimerspec32
ns_to_compat_timeval() ns_to_old_timeval32()
get_compat_itimerspec64() get_old_itimerspec32()
put_compat_itimerspec64() put_old_itimerspec32()
compat_get_timespec64() get_old_timespec32()
compat_put_timespec64() put_old_timespec32()
As we already have aliases in place, this patch addresses only the
instances that are relevant to the system call interface in particular,
not those that occur in device drivers and other modules. Those
will get handled separately, while providing the 64-bit version
of the respective interfaces.
I'm not renaming the timex, rusage and itimerval structures, as we are
still debating what the new interface will look like, and whether we
will need a replacement at all.
This also doesn't change the names of the syscall entry points, which can
be done more easily when we actually switch over the 32-bit architectures
to use them, at that point we need to change COMPAT_SYSCALL_DEFINEx to
SYSCALL_DEFINEx with a new name, e.g. with a _time32 suffix.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Link: https://lore.kernel.org/lkml/20180705222110.GA5698@infradead.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- An implementation for the newly added hv_ops->flush() for the OPAL hvc
console driver backends, I forgot to apply this after merging the hvc driver
changes before the merge window.
- Enable all PCI bridges at boot on powernv, to avoid races when multiple
children of a bridge try to enable it simultaneously. This is a workaround
until the PCI core can be enhanced to fix the races.
- A fix to query PowerVM for the correct system topology at boot before
initialising sched domains, seen in some configurations to cause broken
scheduling etc.
- A fix for pte_access_permitted() on "nohash" platforms.
- Two commits to fix SIGBUS when using remap_pfn_range() seen on Power9 due to
a workaround when using the nest MMU (GPUs, accelerators).
- Another fix to the VFIO code used by KVM, the previous fix had some bugs
which caused guests to not start in some configurations.
- A handful of other minor fixes.
Thanks to:
Aneesh Kumar K.V, Benjamin Herrenschmidt, Christophe Leroy, Hari Bathini, Luke
Dashjr, Mahesh Salgaonkar, Nicholas Piggin, Paul Mackerras, Srikar Dronamraju.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAlt//10THG1wZUBlbGxl
cm1hbi5pZC5hdQAKCRBR6+o8yOGlgLUGD/9y/MPrs+V2lNFhxP+l1jO4Ro0v8DPI
vARjqq06WfppgQgSS1dvWfzLaMFbGe8wPRfL0T1xMOXCZg8Ts/HrgxVBVFYcv6/Q
xBaU5bKztg6HKQbwwO+8B/gdTA3hO7yFVux6JGwsGO5Ebl8Q3UDOdbvYX6XTj3H8
rdiicle9LaI7qodC8bxlBo1Be0YKEW0O/ag179sxXzozzvoPIyFpeX6FL1sAft++
XlQS1MHu4hErSM2rbmyoFCm+SmyRt3CD0NTVmNd2cgw5XexPOBFlnsdgpaK1jJFc
CYu1chP83E91ol1/8NAPkcmPWvP6MGyoqOl75RghooY2D1IJ2GtLKoz2Dvc53ay2
ZlIpMyc2CYIa55Mj18tOV/NbGbh0Lf0Ta++BxqxbcCDt5fq0VxHkoDPqBgWh/tdp
Po7oQc7U2VTKKC3wiLr//nSHpgtSTAWtucDt7oT7GdP8+EMxUZ8teBFIfTkwfuD2
plroEmcYuRD3beI4FAG/iCp5POOCsnHLkKVDl7tyQPl3Yvu8hvyLY9gBS9RN4Unt
/z94YFJtz7UD+VP7jDaPiQS26y0WEJfW8ml0tNxMZVBdksZLPIPN0/EU/04V0jWf
GxynzKMhElxC67tK/Eb43EGiLEZAlbEnJxoOtiCnL1MK+OIJPjg6e7o6qlsmaa+Y
zkXVpxLtkq0OoQ==
=1AUa
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- An implementation for the newly added hv_ops->flush() for the OPAL
hvc console driver backends, I forgot to apply this after merging the
hvc driver changes before the merge window.
- Enable all PCI bridges at boot on powernv, to avoid races when
multiple children of a bridge try to enable it simultaneously. This
is a workaround until the PCI core can be enhanced to fix the races.
- A fix to query PowerVM for the correct system topology at boot before
initialising sched domains, seen in some configurations to cause
broken scheduling etc.
- A fix for pte_access_permitted() on "nohash" platforms.
- Two commits to fix SIGBUS when using remap_pfn_range() seen on Power9
due to a workaround when using the nest MMU (GPUs, accelerators).
- Another fix to the VFIO code used by KVM, the previous fix had some
bugs which caused guests to not start in some configurations.
- A handful of other minor fixes.
Thanks to: Aneesh Kumar K.V, Benjamin Herrenschmidt, Christophe Leroy,
Hari Bathini, Luke Dashjr, Mahesh Salgaonkar, Nicholas Piggin, Paul
Mackerras, Srikar Dronamraju.
* tag 'powerpc-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mce: Fix SLB rebolting during MCE recovery path.
KVM: PPC: Book3S: Fix guest DMA when guest partially backed by THP pages
powerpc/mm/radix: Only need the Nest MMU workaround for R -> RW transition
powerpc/mm/books3s: Add new pte bit to mark pte temporarily invalid.
powerpc/nohash: fix pte_access_permitted()
powerpc/topology: Get topology for shared processors at boot
powerpc64/ftrace: Include ftrace.h needed for enable/disable calls
powerpc/powernv/pci: Work around races in PCI bridge enabling
powerpc/fadump: cleanup crash memory ranges support
powerpc/powernv: provide a console flush operation for opal hvc driver
powerpc/traps: Avoid rate limit messages from show unhandled signals
powerpc/64s: Fix PACA_IRQ_HARD_DIS accounting in idle_power4()
On a shared LPAR, Phyp will not update the CPU associativity at boot
time. Just after the boot system does recognize itself as a shared
LPAR and trigger a request for correct CPU associativity. But by then
the scheduler would have already created/destroyed its sched domains.
This causes
- Broken load balance across Nodes causing islands of cores.
- Performance degradation esp if the system is lightly loaded
- dmesg to wrongly report all CPUs to be in Node 0.
- Messages in dmesg saying borken topology.
- With commit 051f3ca02e ("sched/topology: Introduce NUMA identity
node sched domain"), can cause rcu stalls at boot up.
The sched_domains_numa_masks table which is used to generate cpumasks
is only created at boot time just before creating sched domains and
never updated. Hence, its better to get the topology correct before
the sched domains are created.
For example on 64 core Power 8 shared LPAR, dmesg reports
Brought up 512 CPUs
Node 0 CPUs: 0-511
Node 1 CPUs:
Node 2 CPUs:
Node 3 CPUs:
Node 4 CPUs:
Node 5 CPUs:
Node 6 CPUs:
Node 7 CPUs:
Node 8 CPUs:
Node 9 CPUs:
Node 10 CPUs:
Node 11 CPUs:
...
BUG: arch topology borken
the DIE domain not a subset of the NUMA domain
BUG: arch topology borken
the DIE domain not a subset of the NUMA domain
numactl/lscpu output will still be correct with cores spreading across
all nodes:
Socket(s): 64
NUMA node(s): 12
Model: 2.0 (pvr 004d 0200)
Model name: POWER8 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 64K
L1i cache: 32K
NUMA node0 CPU(s): 0-7,32-39,64-71,96-103,176-183,272-279,368-375,464-471
NUMA node1 CPU(s): 8-15,40-47,72-79,104-111,184-191,280-287,376-383,472-479
NUMA node2 CPU(s): 16-23,48-55,80-87,112-119,192-199,288-295,384-391,480-487
NUMA node3 CPU(s): 24-31,56-63,88-95,120-127,200-207,296-303,392-399,488-495
NUMA node4 CPU(s): 208-215,304-311,400-407,496-503
NUMA node5 CPU(s): 168-175,264-271,360-367,456-463
NUMA node6 CPU(s): 128-135,224-231,320-327,416-423
NUMA node7 CPU(s): 136-143,232-239,328-335,424-431
NUMA node8 CPU(s): 216-223,312-319,408-415,504-511
NUMA node9 CPU(s): 144-151,240-247,336-343,432-439
NUMA node10 CPU(s): 152-159,248-255,344-351,440-447
NUMA node11 CPU(s): 160-167,256-263,352-359,448-455
Currently on this LPAR, the scheduler detects 2 levels of Numa and
created numa sched domains for all CPUs, but it finds a single DIE
domain consisting of all CPUs. Hence it deletes all numa sched
domains.
To address this, detect the shared processor and update topology soon
after CPUs are setup so that correct topology is updated just before
scheduler creates sched domain.
With the fix, dmesg reports:
numa: Node 0 CPUs: 0-7 32-39 64-71 96-103 176-183 272-279 368-375 464-471
numa: Node 1 CPUs: 8-15 40-47 72-79 104-111 184-191 280-287 376-383 472-479
numa: Node 2 CPUs: 16-23 48-55 80-87 112-119 192-199 288-295 384-391 480-487
numa: Node 3 CPUs: 24-31 56-63 88-95 120-127 200-207 296-303 392-399 488-495
numa: Node 4 CPUs: 208-215 304-311 400-407 496-503
numa: Node 5 CPUs: 168-175 264-271 360-367 456-463
numa: Node 6 CPUs: 128-135 224-231 320-327 416-423
numa: Node 7 CPUs: 136-143 232-239 328-335 424-431
numa: Node 8 CPUs: 216-223 312-319 408-415 504-511
numa: Node 9 CPUs: 144-151 240-247 336-343 432-439
numa: Node 10 CPUs: 152-159 248-255 344-351 440-447
numa: Node 11 CPUs: 160-167 256-263 352-359 448-455
and lscpu also reports:
Socket(s): 64
NUMA node(s): 12
Model: 2.0 (pvr 004d 0200)
Model name: POWER8 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 64K
L1i cache: 32K
NUMA node0 CPU(s): 0-7,32-39,64-71,96-103,176-183,272-279,368-375,464-471
NUMA node1 CPU(s): 8-15,40-47,72-79,104-111,184-191,280-287,376-383,472-479
NUMA node2 CPU(s): 16-23,48-55,80-87,112-119,192-199,288-295,384-391,480-487
NUMA node3 CPU(s): 24-31,56-63,88-95,120-127,200-207,296-303,392-399,488-495
NUMA node4 CPU(s): 208-215,304-311,400-407,496-503
NUMA node5 CPU(s): 168-175,264-271,360-367,456-463
NUMA node6 CPU(s): 128-135,224-231,320-327,416-423
NUMA node7 CPU(s): 136-143,232-239,328-335,424-431
NUMA node8 CPU(s): 216-223,312-319,408-415,504-511
NUMA node9 CPU(s): 144-151,240-247,336-343,432-439
NUMA node10 CPU(s): 152-159,248-255,344-351,440-447
NUMA node11 CPU(s): 160-167,256-263,352-359,448-455
Reported-by: Manjunatha H R <manjuhr1@in.ibm.com>
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
[mpe: Trim / format change log]
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 1bd6a1c4b8 ("powerpc/fadump: handle crash memory ranges array
index overflow") changed crash memory ranges to a dynamic array that
is reallocated on-demand with krealloc(). The relevant header for this
call was not included. The kernel compiles though. But be cautious and
add the header anyway.
Also, memory allocation logic in fadump_add_crash_memory() takes care
of memory allocation for crash memory ranges in all scenarios. Drop
unnecessary memory allocation in fadump_setup_crash_memory_ranges().
Fixes: 1bd6a1c4b8 ("powerpc/fadump: handle crash memory ranges array index overflow")
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the recent commit to add an explicit ratelimit state when showing
unhandled signals, commit 35a52a10c3 ("powerpc/traps: Use an
explicit ratelimit state for show_signal_msg()"), I put the check of
show_unhandled_signals and the ratelimit state before the call to
unhandled_signal() so as to avoid unnecessarily calling the latter
when show_unhandled_signals is false.
However that causes us to check the ratelimit state on every call, so
if we take a lot of *handled* signals that has the effect of making
the ratelimit code print warnings that callbacks have been suppressed
when they haven't.
So rearrange the code so that we check show_unhandled_signals first,
then call unhandled_signal() and finally check the ratelimit state.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Notable changes:
- A fix for a bug in our page table fragment allocator, where a page table page
could be freed and reallocated for something else while still in use, leading
to memory corruption etc. The fix reuses pt_mm in struct page (x86 only) for
a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but bring us in
to line with x86 behaviour and/or fix outright bugs. Thanks to Florian Weimer
for reporting many of these.
- A series to improve the hvc driver & related OPAL console code, which have
been seen to cause hardlockups at times. The hvc driver changes in particular
have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in use
anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM CPUs
(controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals to bring it
into line with other arches, including showing the offending VMA and dumping
the instructions around the fault.
Thanks to:
Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Alexey
Spirkov, Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
Arnd Bergmann, Bartosz Golaszewski, Benjamin Herrenschmidt, Bharat Bhushan,
Bjoern Noetel, Boqun Feng, Breno Leitao, Bryant G. Ly, Camelia Groza,
Christophe Leroy, Christoph Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt,
Darren Stevens, Dave Young, David Gibson, Diana Craciun, Finn Thain, Florian
Weimer, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel Stanley,
Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh Salgaonkar, Markus
Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues, Michael Hanselmann, Michael
Neuling, Michael Schmitz, Mukesh Ojha, Murilo Opsfelder Araujo, Nicholas
Piggin, Parth Y Shah, Paul Mackerras, Paul Menzel, Ram Pai, Randy Dunlap,
Rashmica Gupta, Reza Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff,
Scott Wood, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson,
Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat Rao
B, zhong jiang.
-----BEGIN PGP SIGNATURE-----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=PzRz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A fix for a bug in our page table fragment allocator, where a page
table page could be freed and reallocated for something else while
still in use, leading to memory corruption etc. The fix reuses
pt_mm in struct page (x86 only) for a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but
bring us in to line with x86 behaviour and/or fix outright bugs.
Thanks to Florian Weimer for reporting many of these.
- A series to improve the hvc driver & related OPAL console code,
which have been seen to cause hardlockups at times. The hvc driver
changes in particular have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
use anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX
instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM
CPUs (controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals
to bring it into line with other arches, including showing the
offending VMA and dumping the instructions around the fault.
Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
Rao, zhong jiang"
* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
powerpc/mm/book3s/radix: Add mapping statistics
powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
powerpc/mm/hash: Remove unnecessary do { } while(0) loop
powerpc/64s: move machine check SLB flushing to mm/slb.c
powerpc/powernv/idle: Fix build error
powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
powerpc/mm: remove warning about ‘type’ being set
powerpc/32: Include setup.h header file to fix warnings
powerpc: Move `path` variable inside DEBUG_PROM
powerpc/powermac: Make some functions static
powerpc/powermac: Remove variable x that's never read
cxl: remove a dead branch
powerpc/powermac: Add missing include of header pmac.h
powerpc/kexec: Use common error handling code in setup_new_fdt()
powerpc/xmon: Add address lookup for percpu symbols
powerpc/mm: remove huge_pte_offset_and_shift() prototype
powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
powerpc/fadump: handle crash memory ranges array index overflow
...
-----BEGIN PGP SIGNATURE-----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=2Dmn
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a
device below it (Myron Stowe)
- Simplify SHPC existence/permission checks (Bjorn Helgaas)
- Remove hotplug sample skeleton driver (Lukas Wunner)
- Convert pciehp to threaded IRQ handling (Lukas Wunner)
- Improve pciehp tolerance of missed events and initially unstable
links (Lukas Wunner)
- Clear spurious pciehp events on resume (Lukas Wunner)
- Add pciehp runtime PM support, including for Thunderbolt controllers
(Lukas Wunner)
- Support interrupts from pciehp bridges in D3hot (Lukas Wunner)
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph
Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is
supplied (Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum
(Jakub Kicinski)
- Set IRQCHIP_ONESHOT_SAFE for PCI MSI irqchips (Heiner Kallweit)
- Document ACPI description of PCI host bridges (Bjorn Helgaas)
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
- To avoid bus errors, enable PASID only if entire path supports
End-End TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD
Controller (Bjorn Helgaas)
- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
- Remove Aardvark outbound window configuration (Evan Wang)
- Fix Aardvark bridge window sizing issue (Zachary Zhang)
- Convert Aardvark to use pci_host_probe() to reduce code duplication
(Thomas Petazzoni)
- Correct the Cadence cdns_pcie_writel() signature (Alan Douglas)
- Add Cadence support for optional generic PHYs (Alan Douglas)
- Add Cadence power management ops (Alan Douglas)
- Remove redundant variable from Cadence driver (Colin Ian King)
- Add Kirin MSI support (Xiaowei Song)
- Drop unnecessary root_bus_nr setting from exynos, imx6, keystone,
armada8k, artpec6, designware-plat, histb, qcom, spear13xx (Shawn
Guo)
- Move link notification settings from DesignWare core to individual
drivers (Gustavo Pimentel)
- Add endpoint library MSI-X interfaces (Gustavo Pimentel)
- Correct signature of endpoint library IRQ interfaces (Gustavo
Pimentel)
- Add DesignWare endpoint library MSI-X callbacks (Gustavo Pimentel)
- Add endpoint library MSI-X test support (Gustavo Pimentel)
- Remove unnecessary GFP_ATOMIC from Hyper-V "new child" allocation
(Jia-Ju Bai)
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect
(Ray Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
- Fix mobiveil iomem/phys_addr_t type usage (Lorenzo Pieralisi)
- Fix mobiveil missing include file (Lorenzo Pieralisi)
- Add mobiveil Kconfig/Makefile support (Lorenzo Pieralisi)
- Fix mvebu I/O space remapping issues (Thomas Petazzoni)
- Use generic pci_host_bridge in mvebu instead of ARM-specific API
(Thomas Petazzoni)
- Whitelist VMD devices with fast interrupt handlers to avoid sharing
vectors with slow handlers (Keith Busch)
* tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (153 commits)
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI: Limit config space size for Netronome NFP5000
PCI/MSI: Set IRQCHIP_ONESHOT_SAFE for PCI-MSI irqchips
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Check for PCIe Link downtraining
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: mvebu: Drop bogus comment above mvebu_pcie_map_registers()
...
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is supplied
(Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum (Jakub
Kicinski)
* pci/misc:
PCI: Limit config space size for Netronome NFP5000
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Unify PCI and normal DMA direction definitions
PCI: Use IRQF_ONESHOT if pci_request_irq() called with no handler
PCI: Call dma_debug_add_bus() for pci_bus_type from PCI core
PCI: Mark fall-through switch cases before enabling -Wimplicit-fallthrough
# Conflicts:
# drivers/pci/hotplug/pciehp_ctrl.c
- verify depmod is installed before modules_install
- support build salt in case build ids must be unique between builds
- allow users to specify additional host compiler flags via HOST*FLAGS,
and rename internal variables to KBUILD_HOST*FLAGS
- update buildtar script to drop vax support, add arm64 support
- update builddeb script for better debarch support
- document the pit-fall of if_changed usage
- fix parallel build of UML with O= option
- make 'samples' target depend on headers_install to fix build errors
- remove deprecated host-progs variable
- add a new coccinelle script for refcount_t vs atomic_t check
- improve double-test coccinelle script
- misc cleanups and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VjfG
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- verify depmod is installed before modules_install
- support build salt in case build ids must be unique between builds
- allow users to specify additional host compiler flags via HOST*FLAGS,
and rename internal variables to KBUILD_HOST*FLAGS
- update buildtar script to drop vax support, add arm64 support
- update builddeb script for better debarch support
- document the pit-fall of if_changed usage
- fix parallel build of UML with O= option
- make 'samples' target depend on headers_install to fix build errors
- remove deprecated host-progs variable
- add a new coccinelle script for refcount_t vs atomic_t check
- improve double-test coccinelle script
- misc cleanups and fixes
* tag 'kbuild-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (41 commits)
coccicheck: return proper error code on fail
Coccinelle: doubletest: reduce side effect false positives
kbuild: remove deprecated host-progs variable
kbuild: make samples really depend on headers_install
um: clean up archheaders recipe
kbuild: add %asm-generic to no-dot-config-targets
um: fix parallel building with O= option
scripts: Add Python 3 support to tracing/draw_functrace.py
builddeb: Add automatic support for sh{3,4}{,eb} architectures
builddeb: Add automatic support for riscv* architectures
builddeb: Add automatic support for m68k architecture
builddeb: Add automatic support for or1k architecture
builddeb: Add automatic support for sparc64 architecture
builddeb: Add automatic support for mips{,64}r6{,el} architectures
builddeb: Add automatic support for mips64el architecture
builddeb: Add automatic support for ppc64 and powerpcspe architectures
builddeb: Introduce functions to simplify kconfig tests in set_debarch
builddeb: Drop check for 32-bit s390
builddeb: Change architecture detection fallback to use dpkg-architecture
builddeb: Skip architecture detection when KBUILD_DEBARCH is set
...
When idle_power4() hard disables interrupts then finds a soft pending
interrupt, it returns with interrupts hard disabled but without
PACA_IRQ_HARD_DIS set. Commit 9b81c0211c ("powerpc/64s: make
PACA_IRQ_HARD_DIS track MSR[EE] closely") added a warning for that
condition (since disabled).
Fix this by adding the PACA_IRQ_HARD_DIS for that case.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull perf update from Thomas Gleixner:
"The perf crowd presents:
Kernel updates:
- Removal of jprobes
- Cleanup and consolidatation the handling of kprobes
- Cleanup and consolidation of hardware breakpoints
- The usual pile of fixes and updates to PMUs and event descriptors
Tooling updates:
- Updates and improvements all over the place. Nothing outstanding,
just the (good) boring incremental grump work"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
perf trace: Do not require --no-syscalls to suppress strace like output
perf bpf: Include uapi/linux/bpf.h from the 'perf trace' script's bpf.h
perf tools: Allow overriding MAX_NR_CPUS at compile time
perf bpf: Show better message when failing to load an object
perf list: Unify metric group description format with PMU event description
perf vendor events arm64: Update ThunderX2 implementation defined pmu core events
perf cs-etm: Generate branch sample for CS_ETM_TRACE_ON packet
perf cs-etm: Generate branch sample when receiving a CS_ETM_TRACE_ON packet
perf cs-etm: Support dummy address value for CS_ETM_TRACE_ON packet
perf cs-etm: Fix start tracing packet handling
perf build: Fix installation directory for eBPF
perf c2c report: Fix crash for empty browser
perf tests: Fix indexing when invoking subtests
perf trace: Beautify the AF_INET & AF_INET6 'socket' syscall 'protocol' args
perf trace beauty: Add beautifiers for 'socket''s 'protocol' arg
perf trace beauty: Do not print NULL strarray entries
perf beauty: Add a generator for IPPROTO_ socket's protocol constants
tools include uapi: Grab a copy of linux/in.h
perf tests: Fix complex event name parsing
perf evlist: Fix error out while applying initial delay and LBR
...
The machine check code that flushes and restores bolted segments in
real mode belongs in mm/slb.c. This will also be used by pseries
machine check and idle code in future changes.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
