Here is the big staging driver pull request for 4.5-rc1. Lots of
cleanups and fixes here, not as many as some releases, but 800+ isn't
that bad. Full details in the shortlog. All of these have been in
linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlaV0VgACgkQMUfUDdst+ykvAwCeIN/Ot3OuWD/d1RQrcUzh028H
rlUAn3YOHCFlQhAnUI+9KMNjH0CwAJKp
=Oij1
-----END PGP SIGNATURE-----
Merge tag 'staging-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big staging driver pull request for 4.5-rc1.
Lots of cleanups and fixes here, not as many as some releases, but
800+ isn't that bad. Full details in the shortlog. All of these have
been in linux-next for a while"
* tag 'staging-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (843 commits)
Revert "arm64: dts: Add dts files to enable ION on Hi6220 SoC."
staging: gdm724x: constify tty_port_operations structs
staging: gdm72xx: add userspace data struct
staging: gdm72xx: Replace timeval with ktime_t
iio: adc: ina2xx: Fix incorrect report of data endianness to userspace.
iio: light: us5182d: Refactor read_raw function
iio: light: us5182d: Add interrupt support and events
iio: light: us5182d: Fix enable status inconcistency
iio: Make IIO value formating function globally available.
staging: emxx_udc: use list_first_entry_or_null()
staging/emxx_udc: fix 64-bit warnings
STAGING: COMEDI: Using kernel types in plx9080.h
STAGING: COMEDI: Added spaces around binary operators in plx9080.h
STAGING: COMEDI: Fixed format of comments in plx9080.h
staging: comedi: comedilib.h: Coding style warning fix for block comments
staging: comedi: s526: add macros for counter control reg values
staging: comedi: s526: replace counter mode bitfield struct
staging: comedi: check for more errors for zero-length write
staging: comedi: simplify returned errors for comedi_write()
staging: comedi: return error on "write" if no command set up
...
Pull networking updates from Davic Miller:
1) Support busy polling generically, for all NAPI drivers. From Eric
Dumazet.
2) Add byte/packet counter support to nft_ct, from Floriani Westphal.
3) Add RSS/XPS support to mvneta driver, from Gregory Clement.
4) Implement IPV6_HDRINCL socket option for raw sockets, from Hannes
Frederic Sowa.
5) Add support for T6 adapter to cxgb4 driver, from Hariprasad Shenai.
6) Add support for VLAN device bridging to mlxsw switch driver, from
Ido Schimmel.
7) Add driver for Netronome NFP4000/NFP6000, from Jakub Kicinski.
8) Provide hwmon interface to mlxsw switch driver, from Jiri Pirko.
9) Reorganize wireless drivers into per-vendor directories just like we
do for ethernet drivers. From Kalle Valo.
10) Provide a way for administrators "destroy" connected sockets via the
SOCK_DESTROY socket netlink diag operation. From Lorenzo Colitti.
11) Add support to add/remove multicast routes via netlink, from Nikolay
Aleksandrov.
12) Make TCP keepalive settings per-namespace, from Nikolay Borisov.
13) Add forwarding and packet duplication facilities to nf_tables, from
Pablo Neira Ayuso.
14) Dead route support in MPLS, from Roopa Prabhu.
15) TSO support for thunderx chips, from Sunil Goutham.
16) Add driver for IBM's System i/p VNIC protocol, from Thomas Falcon.
17) Rationalize, consolidate, and more completely document the checksum
offloading facilities in the networking stack. From Tom Herbert.
18) Support aborting an ongoing scan in mac80211/cfg80211, from
Vidyullatha Kanchanapally.
19) Use per-bucket spinlock for bpf hash facility, from Tom Leiming.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1375 commits)
net: bnxt: always return values from _bnxt_get_max_rings
net: bpf: reject invalid shifts
phonet: properly unshare skbs in phonet_rcv()
dwc_eth_qos: Fix dma address for multi-fragment skbs
phy: remove an unneeded condition
mdio: remove an unneed condition
mdio_bus: NULL dereference on allocation error
net: Fix typo in netdev_intersect_features
net: freescale: mac-fec: Fix build error from phy_device API change
net: freescale: ucc_geth: Fix build error from phy_device API change
bonding: Prevent IPv6 link local address on enslaved devices
IB/mlx5: Add flow steering support
net/mlx5_core: Export flow steering API
net/mlx5_core: Make ipv4/ipv6 location more clear
net/mlx5_core: Enable flow steering support for the IB driver
net/mlx5_core: Initialize namespaces only when supported by device
net/mlx5_core: Set priority attributes
net/mlx5_core: Connect flow tables
net/mlx5_core: Introduce modify flow table command
net/mlx5_core: Managing root flow table
...
Pull misc vfs updates from Al Viro:
"All kinds of stuff. That probably should've been 5 or 6 separate
branches, but by the time I'd realized how large and mixed that bag
had become it had been too close to -final to play with rebasing.
Some fs/namei.c cleanups there, memdup_user_nul() introduction and
switching open-coded instances, burying long-dead code, whack-a-mole
of various kinds, several new helpers for ->llseek(), assorted
cleanups and fixes from various people, etc.
One piece probably deserves special mention - Neil's
lookup_one_len_unlocked(). Similar to lookup_one_len(), but gets
called without ->i_mutex and tries to avoid ever taking it. That, of
course, means that it's not useful for any directory modifications,
but things like getting inode attributes in nfds readdirplus are fine
with that. I really should've asked for moratorium on lookup-related
changes this cycle, but since I hadn't done that early enough... I
*am* asking for that for the coming cycle, though - I'm going to try
and get conversion of i_mutex to rwsem with ->lookup() done under lock
taken shared.
There will be a patch closer to the end of the window, along the lines
of the one Linus had posted last May - mechanical conversion of
->i_mutex accesses to inode_lock()/inode_unlock()/inode_trylock()/
inode_is_locked()/inode_lock_nested(). To quote Linus back then:
-----
| This is an automated patch using
|
| sed 's/mutex_lock(&\(.*\)->i_mutex)/inode_lock(\1)/'
| sed 's/mutex_unlock(&\(.*\)->i_mutex)/inode_unlock(\1)/'
| sed 's/mutex_lock_nested(&\(.*\)->i_mutex,[ ]*I_MUTEX_\([A-Z0-9_]*\))/inode_lock_nested(\1, I_MUTEX_\2)/'
| sed 's/mutex_is_locked(&\(.*\)->i_mutex)/inode_is_locked(\1)/'
| sed 's/mutex_trylock(&\(.*\)->i_mutex)/inode_trylock(\1)/'
|
| with a very few manual fixups
-----
I'm going to send that once the ->i_mutex-affecting stuff in -next
gets mostly merged (or when Linus says he's about to stop taking
merges)"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
nfsd: don't hold i_mutex over userspace upcalls
fs:affs:Replace time_t with time64_t
fs/9p: use fscache mutex rather than spinlock
proc: add a reschedule point in proc_readfd_common()
logfs: constify logfs_block_ops structures
fcntl: allow to set O_DIRECT flag on pipe
fs: __generic_file_splice_read retry lookup on AOP_TRUNCATED_PAGE
fs: xattr: Use kvfree()
[s390] page_to_phys() always returns a multiple of PAGE_SIZE
nbd: use ->compat_ioctl()
fs: use block_device name vsprintf helper
lib/vsprintf: add %*pg format specifier
fs: use gendisk->disk_name where possible
poll: plug an unused argument to do_poll
amdkfd: don't open-code memdup_user()
cdrom: don't open-code memdup_user()
rsxx: don't open-code memdup_user()
mtip32xx: don't open-code memdup_user()
[um] mconsole: don't open-code memdup_user_nul()
[um] hostaudio: don't open-code memdup_user()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PA5/
-----END PGP SIGNATURE-----
Merge tag 'media/v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"The part of patches for Kernel 4.5. There's nothing really big here:
- driver-specific headers for media devices were moved to separate
directories, in order to make clear what headers belong to the core
kABI and require documentation
- Platform data for media drivers were moved from include/media to
include/linux/platform_data/media
- add a driver for cs3308 8-channel volume control, used on some
high-end capture boards
- lirc.h kAPI header were added at include/uapi/linux
- Driver cleanups, new board additions and improvements"
* tag 'media/v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
Pull vfs xattr updates from Al Viro:
"Andreas' xattr cleanup series.
It's a followup to his xattr work that went in last cycle; -0.5KLoC"
* 'work.xattr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
xattr handlers: Simplify list operation
ocfs2: Replace list xattr handler operations
nfs: Move call to security_inode_listsecurity into nfs_listxattr
xfs: Change how listxattr generates synthetic attributes
tmpfs: listxattr should include POSIX ACL xattrs
tmpfs: Use xattr handler infrastructure
btrfs: Use xattr handler infrastructure
vfs: Distinguish between full xattr names and proper prefixes
posix acls: Remove duplicate xattr name definitions
gfs2: Remove gfs2_xattr_acl_chmod
vfs: Remove vfs_xattr_cmp
Pull vfs RCU symlink updates from Al Viro:
"Replacement of ->follow_link/->put_link, allowing to stay in RCU mode
even if the symlink is not an embedded one.
No changes since the mailbomb on Jan 1"
* 'work.symlinks' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
switch ->get_link() to delayed_call, kill ->put_link()
kill free_page_put_link()
teach nfs_get_link() to work in RCU mode
teach proc_self_get_link()/proc_thread_self_get_link() to work in RCU mode
teach shmem_get_link() to work in RCU mode
teach page_get_link() to work in RCU mode
replace ->follow_link() with new method that could stay in RCU mode
don't put symlink bodies in pagecache into highmem
namei: page_getlink() and page_follow_link_light() are the same thing
ufs: get rid of ->setattr() for symlinks
udf: don't duplicate page_symlink_inode_operations
logfs: don't duplicate page_symlink_inode_operations
switch befs long symlinks to page_symlink_operations
* patchwork: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
Fix a number of build errors due to moving the phy_map and centralizing
interrupt allocation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio device patches moved the bus member in phy_device into a
substructure. This driver got missed. Fix it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Constifies tty_port_operations structure in
the tty code of the gdm724x driver since it
is not modified after its initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the sparse warnings about dereferencing a userspace pointer.
Once I updated the sparse annotations, I noticed a bug in
gdm_wimax_ioctl() where we pass a user space pointer to gdm_update_fsm()
which dereferences it. I fixed this.
Signed-off-by: Wim de With <nauxuron@wimdewith.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct sdu_stamp in the gdm_sdio.h is a timeval type.
'struct timeval now' is used for calculating elapsed time.
32-bit systems using 'struct timeval' will break in the year 2038,
so we have to replace that code with more appropriate types.
This patch changes the gdm72xx driver to use ktime_t.
ktime_get() is better than using do_gettimeofday(),
because it uses the monotonic clock. ktime_sub
are used to subtract two ktime variables.
Build tested this by saying Y to WIMAX_GDM72XX.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New driver features
- us5182
* Add interrupt support and rising / falling threshold events.
Cleanups / fixes to new stuff / minor additions
* Expose the IIO value formatting function for drivers to
make use of internally.
- ina2xx
* Fix wrong channel order
* Fix incorrect reporting of endianness
* Adding documentation of ABI unique to this device
- mma8452
* Drop an unused register description
* Use an enum for the channel index to aid readability
- sca3000
* Use standard NULL comparison style
- us5182
* fix an inconsistency in status of enable (a bug with no real effect until
above patches are applied)
* refactor the read_raw function to improve maintainability / readability.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aiE2
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of new stuff for IIO in the 4.5 cycle.
New driver features
- us5182
* Add interrupt support and rising / falling threshold events.
Cleanups / fixes to new stuff / minor additions
* Expose the IIO value formatting function for drivers to
make use of internally.
- ina2xx
* Fix wrong channel order
* Fix incorrect reporting of endianness
* Adding documentation of ABI unique to this device
- mma8452
* Drop an unused register description
* Use an enum for the channel index to aid readability
- sca3000
* Use standard NULL comparison style
- us5182
* fix an inconsistency in status of enable (a bug with no real effect until
above patches are applied)
* refactor the read_raw function to improve maintainability / readability.
The big one here is the configfs support which has been a long time in the
works but should allow for cleaner ways to do instantiation of those elements
of IIO that aren't directly connected to specific hardware. Lots of cool new
stuff we can use this for in the works!
New core stuff (basically all configfs support related)
* Configfs support
- Core support (was waiting for a configfs patch that went in around 4.4rc2)
- A little fixlet to add a configfs.h to contain a reference to the
configfs_subsystem structure.
* Some infrastructure to simplify handling of software based triggers
(i.e. ones with no actual hardware associated with them)
* A high resolution timer based trigger. This has been around for years
but until the configfs support was ready we didn't have a sensible way
of instantiating instances of it (the method used for the sysfs_trigger
has never been really satisfactory)
New Device Support
* AMS iAQ Volatile Organic Compounds sensor support.
* Freescale imx7d ADC driver
* Maxim MAX30100 oximeter driver (note that for these devices most of the
smart stuff will be in userspace - effectively they are just light sensors
with some interesting led synchronization as far as the kernel is concerned).
* Microchip mcp3421 support added to the mcp3422 driver.
* TI adc124s021 support added to the adc128s052 driver.
* TI ina219, inda226 power monitors. Note that there is an existing hwmon driver
for these parts, the usecase is somewhat different so it is unclear at this
point if the hwmon driver will eventually be replaced by a bridge from
this driver. In the meantime the Kconfig dependencies should prevent both
from being built.
New driver functionality
* us8152d power management support.
Cleanups, fixups
* Use list_for_each_entry_safe instead of list_for_each_safe with the entry
bit coded longhand.
* Select IRQ_WORK for IIO_DUMMY_EVGEN. This is a fix that somehow got lost
when the driver was moved so lets do it again.
* st-accel - drop an unused define.
* vz89x, lidar - optimize i2c transactions by using a single i2c tranfers
instead of multiple calls where supported (fall back to smbus calls as
before if not).
* Use dev_get_platdata() in staging drivers: tsl2x7x, adcs and frequency
drivers instead of direct access to the structure element.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=54PR
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new drivers, functionality and cleanups for the 4.5 cycle.
The big one here is the configfs support which has been a long time in the
works but should allow for cleaner ways to do instantiation of those elements
of IIO that aren't directly connected to specific hardware. Lots of cool new
stuff we can use this for in the works!
New core stuff (basically all configfs support related)
* Configfs support
- Core support (was waiting for a configfs patch that went in around 4.4rc2)
- A little fixlet to add a configfs.h to contain a reference to the
configfs_subsystem structure.
* Some infrastructure to simplify handling of software based triggers
(i.e. ones with no actual hardware associated with them)
* A high resolution timer based trigger. This has been around for years
but until the configfs support was ready we didn't have a sensible way
of instantiating instances of it (the method used for the sysfs_trigger
has never been really satisfactory)
New Device Support
* AMS iAQ Volatile Organic Compounds sensor support.
* Freescale imx7d ADC driver
* Maxim MAX30100 oximeter driver (note that for these devices most of the
smart stuff will be in userspace - effectively they are just light sensors
with some interesting led synchronization as far as the kernel is concerned).
* Microchip mcp3421 support added to the mcp3422 driver.
* TI adc124s021 support added to the adc128s052 driver.
* TI ina219, inda226 power monitors. Note that there is an existing hwmon driver
for these parts, the usecase is somewhat different so it is unclear at this
point if the hwmon driver will eventually be replaced by a bridge from
this driver. In the meantime the Kconfig dependencies should prevent both
from being built.
New driver functionality
* us8152d power management support.
Cleanups, fixups
* Use list_for_each_entry_safe instead of list_for_each_safe with the entry
bit coded longhand.
* Select IRQ_WORK for IIO_DUMMY_EVGEN. This is a fix that somehow got lost
when the driver was moved so lets do it again.
* st-accel - drop an unused define.
* vz89x, lidar - optimize i2c transactions by using a single i2c tranfers
instead of multiple calls where supported (fall back to smbus calls as
before if not).
* Use dev_get_platdata() in staging drivers: tsl2x7x, adcs and frequency
drivers instead of direct access to the structure element.
ARCH_SHMOBILE is coming to arm64, which creates new warnings in allmodconfig:
drivers/staging/emxx_udc/emxx_udc.c: In function '_nbu2ss_out_dma':
drivers/staging/emxx_udc/emxx_udc.c:843:45: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
_nbu2ss_writel(&preg->EP_DCR[num].EP_TADR, (u32)pBuffer);
This is clearly a mistake from confusing a dma_addr_t with a pointer,
so the fix is to use the correct types in two places.
The third warning of this kind is a check for an unaligned pointer,
which should be done by casting the pointer to uintptr_t, not int.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes plx9080.h use kernel types.
Signed-off-by: Moritz König <moritz.koenig@fau.de>
Signed-off-by: Fabian Lang <fabian.lang@fau.de>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds spaces around binary operators in plx9080.h.
Signed-off-by: Moritz König <moritz.koenig@fau.de>
Signed-off-by: Fabian Lang <fabian.lang@fau.de>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the format of comments in plx9080.h.
Signed-off-by: Moritz König <moritz.koenig@fau.de>
Signed-off-by: Fabian Lang <fabian.lang@fau.de>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to comedilib.h file that fixes up following warnings
reported by checkpatch.pl :
I) Block comments use * on subsequent lines.
Apart from it I have remove header file path by base file name as
suggested by community.
Signed-off-by: Jitendra Kumar Khasdev <jkhasdev@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver writes a couple of literal values to the counter
control/status register, 0x8000 to reset the counter, and 0x4000 to load
the counter from preload register 0. Add a bunch of macros to define
these values and other values for the register, based on the Sensoray
526 manual.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses `struct counter_mode_register_t` to describe the 16-bit
counter mode register as a sequence of bitfield members. The struct
appears as the type of one of the members of `union cmReg`, the other
member of which is of type `unsigned short`, so the driver can
manipulate the register value as a whole, or as individual fields.
Although this is fairly convenient, it's not that conventional. The
code also needs to define the bitfield members in ascending or
descending order of the physical bits, depending on whether bitfields
are little- or big-endian.
Rip all that out and replace it with a bunch of macros to set and mask
out bits of the register value, as that's the more conventional way to
do it. A bonus is that we get rid of a load of CamelCase definitions in
the process.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the "write" file operation handler, `comedi_write()` is passed 0 for
the amount to write, some error conditions are currently skipped and the
function just returns 0. Change it to check those error conditions and
return an error value if appropriate. The trickiest case is the check
for when the previously set up asynchronous command has terminated with
an error. In that case, `-EPIPE` is returned (as it is for a write of
non-zero length) and the subdevice gets marked as non-busy.
A zero-length write that returns 0 has no other effects, in particular,
it does not cause the subdevice to be marked as non-busy.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to perform a "write" file operation, an asynchronous COMEDI
command in the "write" direction needs to have been set up by the
current file object on the COMEDI "write" subdevice associated with the
file object. If there is a "write" subdevice, but a command has not
been set up by the file object (or is has been set-up in the wrong
direction), `comedi_write()` currently returns one of two error values
`-EINVAL` or `-EACCES`. `-EACCES` is returned if the command was set up
by a different subdevice, or somewhat randomly, if a COMEDI
"instruction" is currently being processed. `-EINVAL` is returned in
other cases. Simplify it by returning `-EINVAL` for all these cases.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "write" file operation handler, `comedi_write()` returns an error
for pretty much any condition that prevents a "write" going ahead. One
of the conditions that prevents a "write" going ahead is that no
asynchronous command has been set up, but that currently results in a
return value of 0 (unless COMEDI instructions are being processed or an
asynchronous command has been set up by a different file object).
Change it to return `-EINVAL` in this case.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`comedi_write()` copies data from the user buffer to the acquisition
data buffer, which is cyclic, using a single call to `copy_from_user()`.
It currently avoids having to deal with wraparound of the cyclic buffer
by limiting the amount it copies (and the amount returned to the user).
Change it to deal with the wraparound using two calls to
`copy_from_user()` if necessary.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At one point in `comedi_write()`, the variable `n` gets assigned to the
minimum of the parameter `nbytes` and the amount of writeable buffer
space. The way that is done currently is unsafe in the unlikely case
that `nbytes` exceeds `UINT_MAX`, so fix it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In `comedi_write()`, the `n` and `m` variables are of type `int`.
Change them to `unsigned int` as they are used to measure a positive
number of bytes. The `count` variable is also of type `int` and holds
the returned number of bytes written. Change it to type `ssize_t` to
match the function's return type.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`comedi_write()` is the handler for the "write" file operation for
COMEDI devices. It mostly runs without using the main mutex of the
COMEDI device, but uses the `attach_lock` rw_semaphore to protect
against the COMEDI device becoming "detached". A file object can write
data for a COMEDI asynchonous command if it initiated the command. The
COMEDI subdevice is marked as busy when the command is started. At some
point, the "write" handler detects that the command has terminated and
so marks the subdevice as non-busy.
In order to mark the subdevice as non-busy, the "write" handler needs to
release the `attach_lock` rw_semaphore and `acquire the main `mutex`.
There is a vulnerable point between the two, so it checks that the
device is still attached after acquiring the mutex. However, it does
not currently check that the conditions for becoming non-busy still
hold. Add some more checks that the subdevice is still busy with a
command initiated by the same file object, and that the command is in
the correct direction (in case the subdevice supports both "read" and
"write").
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rearrange the code in `comedi_write()` to reduce the amount of
indentation. The code never reiterates the `while` loop once `count`
has become non-zero, so we can check that in the `while` condition to
save an indentation level. (Note that `nbytes` has been checked to be
non-zero before entering the loop, so we can remove that check.) Move
the code that makes the subdevice "become non-busy" outside the `while`
loop, using a new flag variable `become_nonbusy` to decide whether it
needs to be done. This simplifies the wait queue handling so there is a
single place where the task is removed from the wait queue, and we can
remove the `on_wait_queue` flag variable.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the MODULE_DESCRIPTION to something more useful than the
generic "Comedi low-level driver".
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Description is a bit long winded and the same information is in
the Devices. Shorten the Description and tidy up the Devices.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is called as part of the pci_driver (*probe) before
doing the (*auto_attach) of the comedi driver. For aesthetics, move
the function to a more logical place in the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, move these defines after the register defines and rename
them to have namespace associated with the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, move this enum after the register defines and rename
it to have namespace associated with the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This member of the boardinfo is identical to the offset of the boardinfo
in the boardtypes array. It's also passed as the 'context' to the driver
(*auto_attach).
The 'cardtype' is only needed by the (*auto_attach) to determine which
PCI BAR to use and in pci_dio_reset() to handle the board specific code.
Remove the 'cardtype' member and use the 'context' value instead.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, use a common define for the interrupt control and status
registers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, rename this define and fix the alignment.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, replace these defines with a macro.
Refactor the switch in pci_dio_reset() to use common code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, replace these defines with some macros.
Refactor the switch in pci_dio_reset() to not require the fallthrough
comment.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These boards use the same offsets for the interrupt control registers.
For aesthetics, remove the current defines and use common ones.
Fix the switch() in pci_dio_reset() to use common code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These boards use the same offsets for the interrupt control registers.
For aesthetics, remove the current defines and use common ones.
Fix the switch() in pci_dio_reset() to use common code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, use a common comment for the switch() that disables and clears
interrupts.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, move the disable of the channel freeze for the PCI-1752
and PCI-1756 boards out of the switch used to disable and clear interrupts.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, use a default case in the switch (board->cardtype) used
to reset the various boards.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These defines are only used to initialize the diosubd_data 'addr' members
in the boardinfo. For aesthetics, just open-code the values and remove the
defines.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
