Add missing entries into i2c-i801 documentation and Kconfig about recently
added Intel DNV and Broxton.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In some cases, we could start a new i2c transfer with the RXRDY flag
set. It is not a clean state and it leads to print annoying error
messages even if there no real issue. The cause is only having garbage
data in the Receive Holding Register because of a weird behavior of the
RXRDY flag.
Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71 ("i2c: at91: fix a race condition when using the DMA controller")
Cc: stable@vger.kernel.org #4.1
Use timer API function setup_timer instead of init_timer to
initialize the timer.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although I2C mux devices are easily enumerated using ACPI (_HID/_CID or
device property compatible string match), enumerating I2C client devices
connected through an I2C mux needs a little extra work.
This change implements a method for describing an I2C device hierarchy that
includes mux devices by using an ACPI Device() for each mux channel along
with an _ADR to set the channel number for the device. See
Documentation/acpi/i2c-muxes.txt for a simple example.
To make this work the ismt, i801, and designware pci/platform devs now
share an ACPI companion with their I2C adapter dev similar to how it's done
in OF. This is done on the assumption that power management functions will
not be called directly on the I2C dev that is sharing the ACPI node.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
TWSI_ILCR & TWSI_IWCR registers are used to adjust clock rate
of standard & fast mode in pxa910/988; so this patch adds these two new
entries to "struct pxa_reg_layout" and "struct pxa_i2c".
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
[wsa: white space fixes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_* APIs to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The first part of the comment is wrong since November 2007, delete it.
The second part of the comment is related to I2C_PEC, not I2C_SLAVE, so
move it where it belongs.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ioctl is named I2C_RDWR for "I2C read/write". But references to it
were misspelled "rdrw". Fix them.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In prima2 and atlas7, due to some hardware design issue. we
need to adjust the divider ratio a little according to i2c
bus frequency ranges.
Since i2c is open drain interface that allows the slave to
stall the transaction by holding the SCL line at '0', the RTL
implementation is waiting for SCL feedback from the pin after
setting it to High-Z ('1'). This wait adds to the high-time
interval counter few cycles of the input synchronization
(depending on the SCL_FILTER_REG field), and also the time it
takes for the board pull-up resistor to rise the SCL line.
For slow SCL settings these additions are negligible, but they
start to affect the speed when clock is set to faster frequencies.
This patch is based on the actual tests, and it makes SCL more
accurate.
Signed-off-by: Guoying Zhang <Guoying.Zhang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to Documentation/i2c/fault-codes the response to a bus NACK
should be -ENXIO, so fix the error code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the SMBUS PCI ID of Intel Broxton.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel DNV SoC has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.
Add DNV PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
mt65xx i2c controller initial setting will be cleared after system suspend,
so we should init mt65xx i2c controller again when system resume.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc. This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc. This adapter is so simple that
it has no FIFO in it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The patch reverts commit a445900c90 (i2c: designware: Add support for
AMD I2C controller). It never worked anyhow because it did not register
a proper clkdev.
Since kernel 4.1 starts to support APD, there is no need to get freq
from id->driver_data for AMD0010. clkdev is supposed to be already
registered in APD.
So, revert old design and make AMD0010 looks like other ones.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In some cases a NACK interrupt may be pending in the Status Register (SR)
as a result of a previous transfer. However at91_do_twi_transfer() did not
read the SR to clear pending interruptions before starting a new transfer.
Hence a NACK interrupt rose as soon as it was enabled again at the I2C
controller level, resulting in a wrong sequence of operations and strange
patterns of behaviour on the I2C bus, such as a clock stretch followed by
a restart of the transfer.
This first issue occurred with both DMA and PIO write transfers.
Also when a NACK error was detected during a PIO write transfer, the
interrupt handler used to wrongly start a new transfer by writing into the
Transmit Holding Register (THR). Then the I2C slave was likely to reply
with a second NACK.
This second issue is fixed in atmel_twi_interrupt() by handling the TXRDY
status bit only if both the TXCOMP and NACK status bits are cleared.
Tested with a at24 eeprom on sama5d36ek board running a linux-4.1-at91
kernel image. Adapted to linux-next.
Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71 ("i2c: at91: fix a race condition when using the DMA controller")
Cc: stable@vger.kernel.org #4.1
Commit ("i2c: designware: Rename platform driver probe and PM
functions") introduced "'dw_i2c_plat_prepare' undeclared here" and
"'dw_i2c_plat_complete' undeclared here" build errors when
CONFIG_PM_SLEEP is not set.
Fix this by renaming NULL defined dw_i2c_prepare and dw_i2c_complete PM
hooks to dw_i2c_plat_prepare and dw_i2c_plat_complete since this was
obviously missing from the commit.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), Renesas R-Car SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to use platform data
anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[wsa: removed now unused ret value and cast to proper enum type]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. It is compitable to Gen2 SoCs, so
reuse the settings.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. I add a new type because this version
has new features (e.g. DMA) which will be added somewhen later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows using OpenCores I2C controller attached to its host in
native-endian mode with bi-endian CPUs. Example of such system is Xtensa
XTFPGA platform.
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-au1550 driver has to program various setup and hold times
for the sda/scl signals by hand. The current values seem to be
working best when the driver is supplied with 50MHz, however on the
DB1300 board 48MHz is the closest we can get to it, and the timings
are a bit too tight for that, leading to the last bit of a transmission
sometimes being swallowed. This manifests itself in wrong readings
of the ne1619 sensor and inability to configure the wm8731 i2s codec.
With the relaxed timings, both the sensor and the i2s codec can now
be accessed more reliably over a wider range of I2C block input
frequencies.
Verified on DB1200, DB1300 and DB1550 boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This code is repeated in probe:
i2c_dev->adapter.algo = &tegra_i2c_algo;
Cc: Donglin Peng <pengdonglin137@163.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to "KeyStone Architecture Inter-IC Control Bus User Guide", fixed
additive part of frequency divisors (referred as "d" in the code and datasheet)
always equals to 6, independent of module clock prescaler.
module clock frequency
master clock frequency = ----------------------
(ICCL + 6) + (ICCH + 6)
It was not the case with original Davinci IP. Introduce new compatible property
"ti,keystone-i2c", which triggers special handling in the driver.
Without this change Keystone-based systems (having 204.8MHz input clock) choose
prescaler 29 (PSC=28). Using d=5 in this case leads to bus bitrate ~353kHz
instead of requested 400kHz. After correction, assuming d=6 bus rate is ~392kHz.
This gives ~11% transfer rate increase.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Hemanth Guruva Reddy <hemanth.guruva_reddy@nokia.com>
Tested-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Issue the warning in all error paths when unable to register MSI or its
handler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Propagate actual return code when requesting interrupt fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
struct pci_dev already has a flag to track if MSI is enabled or not. Use it
directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to repeat the work that is already done in the PCI driver
core. Remove suspend and resume callbacks.
Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
pcim_release() will release any requested region. There is no need to duplicate
this effort in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The way we currently scan I2C devices behind an I2C host controller does not
work in cases where the I2C device in question is not declared directly below
the host controller ACPI node.
This is perfectly legal according the ACPI 6.0 specification and some existing
systems are doing this.
To be able to enumerate all devices which are connected to a certain I2C host
controller we need to rework the current I2C scanning routine a bit. Instead of
scanning directly below the host controller we scan the whole ACPI namespace
for present devices with valid I2cSerialBus() connection pointing to the host
controller in question.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is some code duplication in i2c-designware-platdrv and
i2c-designware-pcidrv probe functions. What is even worse that duplication
requires i2c_dw_xfer(), i2c_dw_func() and i2c_dw_isr() i2c-designware-core
functions to be exported.
Therefore move common code into new i2c_dw_probe() and make functions above
local to i2c-designware-core.
While merging the code patch does following functional changes:
- I2C Adapter name will be "Synopsys DesignWare I2C adapter". Previously it
was used for platform and ACPI devices but PCI device used
"i2c-designware-pci".
- Using device name for interrupt name. Previous it was platform device name,
ACPI device name or "i2c-designware-pci".
- Error code from devm_request_irq() and i2c_add_numbered_adapter() will be
printed in case of error.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it easier to distinguish between i2c-designware-platdrv and
i2c-designware-core functions and to be consistent with
i2c-designware-pcidrv.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
dw_readl() and dw_writel() are not used outside of i2c-designware-core and
they are not exported so make them static and remove their forward
declaration.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_dw_is_enabled() became unused by the commit be58eda775
("i2c: designware-pci: Cleanup driver power management") and
i2c_dw_enable() by the commit 3a48d1c08f ("i2c: prevent spurious
interrupt on Designware controllers").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Device must not generate interrupts before registering the interrupt
handler so move i2c_dw_disable_int() before requesting it.
There are no known issues with this. The code has been here since commit
fe20ff5c7e ("i2c-designware: Add support for Designware core behind PCI
devices.").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to clear interrupts in i2c_dw_pci_probe() since only place
where interrupts are unmasked is i2c_dw_xfer_init() and there interrupts
are always cleared after commit 2a2d95e9d6 ("i2c: designware: always
clear interrupts before enabling them").
This allows to cleanup the code and replace i2c_dw_clear_int() in
i2c_dw_xfer_init() by direct register read as there are no other callers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The requested bit rate can be outside the range supported by the driver.
The maximum bit rate this driver supports at the moment is 400Khz.
If the requested bit rate is larger than the maximum supported by the
driver, set the bitrate to the maximum supported before bitrate_khz is
calculated.
Maximum speed supported by the driver can be increased to 1Mhz by
adding support for "fast plus mode" in the future.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clear line status and all generated interrupts from the interrupt
status register before starting a transfer, as we may have
unserviced interrupts from previous transfers that might be
handled in the context of the new transfer.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c->line_status accumulates the line status bits that have been seen
with each interrupt. As we're only interested in that bit from the
current interrupt, refer to line_status (the argument to img_i2c_auto)
instead of i2c->line_status.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, after determining the minimum value for the High period
(TCKH) the remainder of the internal clock pulses is set as the Low
period (TCKL). This causes the i2c clock duty cycle to be much less
than 50%.
Modify the starting position to TCKH and TCKL at 50% of the internal
clock, and adjusts the TCKH and TCKL values from there should the
minimum value for TCKL not be met. This results in duty cycles closer
to 50%.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using % can be slow depending on the architecture.
Using DIV_ROUND_UP is nicer and more efficient way to do it.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
