During suspend client MSIx vectors are freed while they are still
in use causing a crash on entering S3.
Fix this calling client close before freeing up its MSIx vectors.
Also update the client MSIx vectors on resume before client
open is called.
Fixes commit b980c0634f ("i40e: shutdown all IRQs and disable MSI-X
when suspended")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting link settings on backplane devices shouldn't be allowed.
This patch adds one more device id to the list which we check
that against.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_set_link_ksettings and i40e_get_link_ksettings use different
codepaths to check available and supported advertisement modes. This
creates scenarios where it's possible to set a mode that's not allowed,
resulting in a link down.
Fix setting advertisement in i40e_set_link_ksettings by calling
i40e_get_link_ksettings to check what modes are allowed.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we re-enable ATR we need to restore the input set for TCPv4
filters, in order for ATR to function correctly. We already do this for
the normal case of re-enabling ATR when disabling ntuple support.
However, when re-enabling ATR after the last TCPv4 filter is removed (but
when ntuple support is still active), we did not restore the TCPv4
filter input set.
This can cause problems if the TCPv4 filters from FDir had changed the
input set, as ATR will no longer behave as expected.
When clearing the ATR auto-disable flag, make sure we restore the TCPv4
input set to avoid this.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch overwrites number of ports for X722 devices with support
for OCP PHY mezzanine.
The old method with checking if port is disabled in the PRTGEN_CNF
register cannot be used in this case. When the OCP is removed, ports
were seen as disabled, which resulted in wrong calculation of partition
id, that caused WoL to be disabled on certain ports.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch needs to expand on the logic for re-enabling ATR. Doing
so would cause some code to break the 80-character line limit.
To reduce the level of indentation, factor out helper functions for
re-enabling ATR and SB rules.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When hardware has trouble with a particular filter, we delete it from
the list. Unfortunately, we did not properly update the per-filter
statistic when doing so.
Create a helper function to handle this, and properly reduce the
necessary counter so that it tracks the number of active filters
properly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VF requests adding of MAC filters the checking is done against number
of already present MAC filters not adding them at the same time. It makes
it possible to add a bunch of filters at once possibly exceeding
acceptable limit of I40E_VC_MAX_MAC_ADDR_PER_VF filters.
This happens because when checking vf->num_mac, we do not check how many
filters are being requested at once. Modify the check function to ensure
that it knows how many filters are being requested. This allows the
check to ensure that the total number of filters in a single request
does not cause us to go over the limit.
Additionally, move the check to within the lock to ensure that the
vf->num_mac is checked while holding the lock to maintain consistency.
We could have simply moved the call to i40e_vf_check_permission to
within the loop, but this could cause a request to be non-atomic, and
add some but not all the addresses, while reporting an error code. We
want to avoid this behavior so that users are not confused about which
filters have or have not been added.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We used to use the function i40e_vlan_rx_register as a way to hook
into the now defunct .ndo_vlan_rx_register netdev hook. This was
removed but we kept the function around because we still used it
internally to control enabling or disabling of VLAN stripping.
As pointed out in upstream review, VLAN stripping is only used in a
single location and the previous function is quite small, just inline
it into i40e_restore_vlan() rather than carrying the function
separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix for "Resource temporarily unavailable" problem when virsh is
trying to attach a device to VM. When the VF driver is loaded on
host and virsh is trying to attach it to the VM and set a MAC
address, it ends with a race condition between i40e_reset_vf and
i40e_ndo_set_vf_mac functions. The bug is fixed by adding polling
in i40e_ndo_set_vf_mac function For when the VF is in Reset mode.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_fcoe support was removed via commit 9eed69a914 ("i40e: Drop FCoE code from core driver files")
But this left files in place but un-compilable.
Let's finish the cleaning.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These two lines are indented too far.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function i40e_find_vsi_from_id can potentially return null, hence
VSI may be null, so defensively check it is non-null before
dereferencing it to check the seid.
Fixes: e284fc2804 ("i40e: Add and delete cloud filter")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_detect_recover_hung function uses the i40e_get_tx_pending
function to determine if there are packets stalled on the ring.
i40e_get_tx_pending calculates the pending packets using the head
writeback value and HW tail. If the queue is stopped and we lose the
interrupt to update our next_to_clean then we a) won't get another
interrupt to clean because queue is stopped b) we won't catch the
problem with i40e_detect_recover_hung because the HW values look like
there's no packets waiting to be transmitted. Using the SW values we
can catch the issue because next_to_clean will be out of sync with head
writeback.
This has the added benefit being less CPU intensive because we don't
need to reach into the hardware to get the values.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces new ethtool private flag used for
forcing true link state. Function i40e_force_link_state that implements
this functionality was added, it sets phy_type = 0 in order to
work-around firmware's LESM. False positive error messages were
suppressed.
The ndo_open() should not succeed if there were issues with forcing link
state to be UP.
Added I40E_PHY_TYPES_BITMASK define with all phy types OR-ed together in
one bitmask. Added after phy type definition, so it will be hard to
forget to include new phy types to the bitmask.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch provides support to add or delete cloud filter for queue
channels created for ADq on VF.
We are using the HW's cloud filter feature and programming it to act
as a TC filter applied to a group of queues.
There are two possible modes for a VF when applying a cloud filter
1. Basic Mode: Intended to apply filters that don't need a VF to be
Trusted. This would include the following
Dest MAC + L4 port
Dest MAC + VLAN + L4 port
2. Advanced Mode: This mode is only for filters with combination that
requires VF to be Trusted.
Dest IP + L4 port
When cloud filters are applied on a trusted VF and for some reason
the same VF is later made as untrusted then all cloud filters
will be deleted. All cloud filters has to be re-applied in
such a case.
Cloud filters are also deleted when queue channel is deleted.
Testing-Hints:
=============
1. Adding Basic Mode filter should be possible on a VF in
Non-Trusted mode.
2. In Advanced mode all filters should be able to be created.
Steps:
======
1. Enable ADq and create TCs using TC mqprio command
2. Apply cloud filter.
3. Turn-off the spoof check.
4. Pass traffic.
Example:
========
1. tc qdisc add dev enp4s2 root mqprio num_tc 4 map 0 0 0 0 1 2 2 3\
queues 2@0 2@2 1@4 1@5 hw 1 mode channel
2. tc qdisc add dev enp4s2 ingress
3. ethtool -K enp4s2 hw-tc-offload on
4. ip link set ens261f0 vf 0 spoofchk off
5. tc filter add dev enp4s2 protocol ip parent ffff: prio 1 flower\
dst_ip 192.168.3.5/32 ip_proto udp dst_port 25 skip_sw hw_tc 2
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch handles the request from ADq enabled VF to allocate
bandwidth to each traffic class which means for each VSI.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch takes care of freeing up all the VSIs, queues and
other ADq related software and hardware resources, when a user
requests for deletion of ADq on VF.
Example command:
tc qdisc del dev eth0 root
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables ADq and creates queue channels on a VF. An ADq
enabled VF can have up to 4 VSIs and each one of them represents
a traffic class and this is termed as a queue channel. Each of these
VSIs can have up to 4 queues. This patch services the request for
enabling ADq and adds queue channel based on the TC mqprio info
provided by the user in the VF.
Initially a check is made to see if spoof check is OFF, if not ADq
will not be enabled. PF notifies VF for a reset in order to complete
the creation of ADq resources i.e. creation of additional VSIs and
allocation of queues as per TC information, all in the reset path.
Steps:
======
1. Turn off the spoof check
2. Enable ADq using tc mqprio command with or without rate limit.
3. Pass traffic.
Example:
========
% ip link set dev eth0 vf 0 spoofchk off
% tc qdisc add dev $iface root mqprio num_tc 4 map\
0 0 0 0 1 1 1 1 2 2 2 2 3 3 3 3 queues\
4@0 4@4 4@8 4@8 hw 1 mode channel
Expected results:
=================
1. Total number of queues for the VF should be sum of queues of all TCs.
2. Traffic flow should be normal without errors.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC, FW Version and NPAR check used to determine
if shutting off the FW LLDP engine is supported is not
using the usual feature check mechanism.
This patch fixes the problem by moving the feature check
to i40e_sw_init in order to set a flag in pf->hw_features
that ethtool will use for priv_flags disable operation.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Broadcast filters can now cause overflow promiscuous to trigger when
adding "too many" VLANs to all the ports of a device and the driver
needs a way to exit overflow promiscuous once triggered.
Currently the driver looks to see if there are "too many" filters and/or
we have any failed filters to determine when it is safe to exit overflow
promiscuous. If we trigger overflow promiscuous with broadcast filters,
any new filters added will be "auto-failed" until we exit overflow
promiscuous. Since the user can't manually remove the failed broadcast
filters for VLANs (nor should we expect the user to do such), there is
no way to exit overflow promiscuous without reloading the driver.
The easiest way to do this is to remove the shortcut to "auto-fail"
filters in overflow promiscuous. If the user removes the VLANs, the
failed filters will be removed and since we're no longer "auto-failing"
new filters, we'll eventually get a good set of filters and exit
overflow promiscuous.
This has the side benefit of making filter state more explicit in that
if a filter says it's failed we know for a fact it failed and not just
assuming it will if we're in overflow promiscuous. This is nice because
if the user removes some filters and then adds some, even if we're in
overflow promiscuous, the filter might succeed; we were just assuming it
won't because the user hasn't rectified other existing failed filters.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code here is quite complex and easy to screw up. Let's see if we
can't improve the readability and maintainability a bit. This refactors
out promisc_changed into two variables 'old_overflow' and 'new_overflow'
which makes it a bit clearer when we're concerned about when and how
overflow promiscuous is changed. This also makes so that we no longer
need to pass a boolean pointer to i40e_aqc_add_filters. Instead we can
simply check if we changed the overflow promiscuous flag since the
function start.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When adding a bunch of VLANs to all the ports on a device, it's possible
to run out of space for broadcast filters. The driver should trigger
overflow promiscuous in this circumstance to prevent traffic from being
unexpectedly dropped.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Could a Bad Person do Bad Things to a server if they found these
addresses printed in the log? Who knows? But let's not take that risk.
Remove pointers from a bunch of printks. In some cases, I was able to
adjust the message to indicate whether or not the value was null. In
others, I just removed the entire message as there was really no hope of
saving it.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warning:
drivers/net/ethernet/intel/i40e/i40e_main.c:5440:5: warning:
symbol 'i40e_get_link_speed' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces the existing mechanism for determining the correct
value to program for adaptive ITR with yet another new and more
complicated approach.
The basic idea from a 30K foot view is that this new approach will push the
Rx interrupt moderation up so that by default it starts in low latency and
is gradually pushed up into a higher latency setup as long as doing so
increases the number of packets processed, if the number of packets drops
to 4 to 1 per packet we will reset and just base our ITR on the size of the
packets being received. For Tx we leave it floating at a high interrupt
delay and do not pull it down unless we start processing more than 112
packets per interrupt. If we start exceeding that we will cut our interrupt
rates in half until we are back below 112.
The side effect of these patches are that we will be processing more
packets per interrupt. This is both a good and a bad thing as it means we
will not be blocking processing in the case of things like pktgen and XDP,
but we will also be consuming a bit more CPU in the cases of things such as
network throughput tests using netperf.
One delta from this versus the ixgbe version of the changes is that I have
made the interrupt moderation a bit more aggressive when we are in bulk
mode by moving our "goldilocks zone" up from 48 to 96 to 56 to 112. The
main motivation behind moving this is to address the fact that we need to
update less frequently, and have more fine grained control due to the
separate Tx and Rx ITR times.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is mostly prep-work for replacing the current approach to
programming the dynamic aka adaptive ITR. Specifically here what we are
doing is splitting the Tx and Rx ITR each into two separate values.
The first value current_itr represents the current value of the register.
The second value target_itr represents the desired value of the register.
The general plan by doing this is to allow for deferring the update of the
ITR value under certain circumstances. For now we will work with what we
have, but in the future I hope to change the behavior so that we always
only update one ITR at a time using some simple logic to determine which
ITR requires an update.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using the register value for the defines when setting up the
ring ITR we can just use the actual values and avoid the use of shifts and
macros to translate between the values we have and the values we want.
This helps to make the code more readable as we can quickly translate from
one value to the other.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The CLEARPBA bit in the dynamic interrupt control register actually has
no effect either way on the hardware. As per errata 28 in the XL710
specification update the interrupt is actually cleared any time the
register is written with the INTENA_MSK bit set to 0. As such the act of
toggling the enable bit actually will trigger the interrupt being
cleared and could lead to potential lost events if auto-masking is
not enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a further clean-up related to the change over to using
q_vector->reg_idx when accessing the ITR registers. Specifically the code
appears to have several other spots where we were computing the register
offset manually and this resulted in errors in a few spots.
Specifically in the i40evf functions for mapping queues to vectors it
appears we may have had an off by 1 error since (v_idx - 1) for the first
q_vector with an index of 0 would result in us returning -1 if I am not
mistaken.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in i40e_set_priv_flags we use new_flags to check for the
I40E_FLAG_DISABLE_FW_LLDP flag. This is an issue for a few a reasons.
DISABLE_FW_LLDP is persistent across reboots/driver reloads. This means
we need some way to detect if FW LLDP is enabled on init. We do this by
trying to init_dcb and if it fails with EPERM we know LLDP is disabled
in FW.
This could be a problem on older FW versions or NPAR enabled PFs because
there are situations where the FW could disable LLDP, but they do _not_
support using this flag to change it. If we do end up in this
situation, the flag will be set, then when the user tries to change any
priv flags, the driver thinks the user is trying to disable FW LLDP on a
FW that doesn't support it and essentially forbids any priv flag
changes.
The fix is simple, instead of checking if this flag is set, we should be
checking if the user is trying to _change_ the flag on unsupported FW
versions.
This patch also adds a comment explaining that the cmpxchg is the point
of no return. Once we put the new flags into pf->flags we can't back
out.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a warning message when the link-down-on-close flag is
setting on. The warning is printed only on MFP devices
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds necessary delay for 4.33 firmware to recover after
EMP reset. Without this patch driver occasionally reinitializes
structures too quickly to communicate with firmware after EMP reset
causing AdminQ to timeout.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The logic for dynamic ITR update is confusing at best as there were odd
paths chosen for how to find the rings associated with a given queue based
on the vector index and other inconsistencies throughout the code.
This patch is an attempt to clean up the logic so that we can more easily
understand what is going on. Specifically if there is a Rx or Tx ring that
is enabled in dynamic mode on the q_vector it is allowed to override the
other side of the interrupt moderation. While it isn't correct all this
patch is doing is cleaning up the logic for now so that when we come
through and fix it we can more easily identify that this is wrong.
The other big change made here is that we replace references to:
vsi->rx_rings[q_vector->v_idx]->itr_setting
with:
q_vector->rx.ring->itr_setting
The general idea is we can avoid the long pointer chase since just
accessing q_vector->rx.ring is a single pointer access versus having to
chase down vsi->rx_rings, and then finding the pointer in the array, and
finally chasing down the itr_setting from there.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rings are already split out into Tx and Rx rings so it doesn't make
sense to have any single ring store both a Tx and Rx itr_setting value.
Since that is the case drop the pair in favor of storing just a single ITR
value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'bufer' should be 'buffer'
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the number of queues per enabled TC and report available queues
to the kernel without having to limit them to the max RSS limit so
they are available to be mapped for XPS. This allows a queue per
processing thread available for handling traffic for the given
traffic class.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compared to ixgbe and other previous Intel drivers the i40e and i40evf
drivers actually reserve 2 additional descriptors in maybe_stop_tx for
cache line alignment. We need to update DESC_NEEDED to reflect this as
otherwise we are more likely to return TX_BUSY which will cause issues with
things like xmit_more.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch suppresses the message about invalid TC mapping and wrong
selected TX queue. The root cause of this bug was setting too many
TC queue pairs on huge multiprocessor machines. When quantity of the
TC queue pairs is exceeding MSI-X vectors count then TX queue number
can be selected beyond actual TX queues amount.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The drivers for i40e and i40evf had a reg_idx value stored in the q_vector
that was going completely unused. I can only assume this was copied over
from ixgbe and nobody knew how to use it.
I'm going to make use of the value to avoid having to compute the vector
and thus the register index for multiple paths throughout the drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 36777d9fa2 ("i40e: check current configured input set when
adding ntuple filters") some code was added to report the input set
mask for a given filter when reporting it to the user.
This code is necessary so that the reported filter correctly displays
that it is or is not masking certain fields.
Unfortunately the code was incorrect. Development error accidentally
swapped the mask values for the IPv4 addresses with the L4 port numbers.
The port numbers are only 16bits wide while IPv4 addresses are 32 bits.
Unfortunately we assigned only 16 bits to the IPv4 address masks.
Additionally we assigned 32bit value 0xFFFFFFF to the TCP port numbers.
This second part does not matter as the value would be truncated to
16bits regardless, but it is unnecessary.
Fix the reported masks to properly report that the entire field is
masked.
Fixes: 36777d9fa2 ("i40e: check current configured input set when adding ntuple filters")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our hardware does not allow situations where two filters might conflict
when matching. Essentially hardware only programs one filter for each
set of matching criteria. We don't support filters with overlapping
input sets, because each flow type can only use a single input set.
Additionally, different flow types will never have overlapping matches,
because of how the hardware parses the flow type before checking
matching criteria.
For this reason, we do not need or use the location number when
programming filters to hardware.
In order to avoid confusing scenarios with filters that match the same
criteria but program the flow to different queues, do not allow multiple
filters that match identical criteria to be programmed.
This ensures that we avoid odd scenarios when deleting filters, and when
programming new filters that match the same criteria.
Instead, users that wish to update the criteria for a filter must use
the same location id, or must delete all the matching filters first.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When implementing support for IP_USER_FLOW filters, we correctly
programmed a filter for both the non fragmented IPv4/Other filter, as
well as the fragmented IPv4 filters. However, we did not properly
program the input set for fragmented IPv4 PCTYPE. This meant that the
filters would almost certainly not match, unless the user specified all
of the flow types.
Add support to program the fragmented IPv4 filter input set. Since we
always program these filters together, we'll assume that the two input
sets must match, and will thus always program the input sets to the same
value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
kdump fails in the system when used in conjunction with Ethernet driver
X722/X710. This is mainly because when we are resource constrained i.e.
when we have just one online_cpus, we are enabling VMDq and iWARP. It
doesn't make sense to enable them with just one CPU and starve kdump
for lack of IRQs.
So don't enable VMDq or iWARP when we just have a single CPU.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using ethtool --set-priv-flags disable-fw-lldp <on/off> is persistent
across reboots/reloads so we need some mechanism in the driver to detect
if it's on or off on init so we can set the ethtool private flag
appropriately. Without this, every time the driver is reloaded the flag
will default to off regardless of whether it's on or off in FW.
We detect this by first attempting to program DCB and if AQ fails
returning I40E_AQ_RC_EPERM, we know that LLDP is disabled in FW.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement the private flag disable-fw-lldp for ethtool
to disable the processing of LLDP packets by the FW.
This will stop the FW from consuming LLDPDU and cause
them to be sent up the stack.
The FW is also being configured to apply a default DCB
configuration on link up.
Toggling the value of this flag will also cause a PF reset.
Disabling FW DCB will also disable DCBx.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As we have added more flags, we need to now use more
bits and have over flooded the 32 bit size. So
make it 64.
Also change all the existing bits to unsigned long long
bits.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables driver to display LLDP information on the vSphere Web
Client with Intel adapters (X710, XL710) and Distributed Virtual Switch.
Signed-off-by: Upasana Menon <upasana.menon@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the i40e/i40evf_set_itr_per_queue function by
dropping all the unneeded pointer chases. Instead we can just pull out the
pointers for the Tx and Rx rings and use them throughout the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reorders i40e_add_del_fdir and i40e_update_ethtool_fdir_entry
calls so that we first remove an already existing filter (inside
i40e_update_ethtool_fdir_entry using i40e_add_del_fdir) and then
we add a new one with i40e_add_del_fdir.
After applying this patch, creating multiple identical filters (with
the same location) one after another doesn't revert their behavior
but behaves correctly.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FW has the ability to return a critical error on every AQ command.
When this critical error occurs then we need to send the correct response
to the caller.
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a768 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Client close is overloaded to handle both un-registration and
netdev down event. On netdev down, i40iw client close is called
which unregisters the RDMA dev and this is too destructive
since the netdev is still registered.
Do not call client close/open on netdev down/up events. Instead
disable the PE TCP_ENA flag during a netdev down event. This
blocks all TCP traffic to the RDMA Protocol Engine. On netdev up,
re-enable the flag.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.
If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.
This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.
The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts. By triggering a SW
interrupt, interrupts are forced on. If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.
This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix solves an issue occurring while calling i40e_led_set function
from the driver with "blink" parameter set as TRUE. This call resulted
in Activity LED blinking instead of Link LED, which may lead to errors
in physically identifying the port, since Activity LED may be blinking
for different reasons as well.
Signed-off-by: Michal Kuchta <michal.kuchta@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new I40E_NVMUPD_GET_AQ_EVENT state to allow
retrieval of AdminQ events as a result of AdminQ commands sent
to firmware.
Add preservation flags support on X722 devices for NVM update
AdminQ function wrapper. Add new parameter and handling to
nvmupdate admin queue function intended to allow nvmupdate tool
to configure the preservation flags in the AdminQ command.
This is required to implement FlatNVM on X722 devices.
Signed-off-by: Pawel Jablonski <pawel.jablonski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
track_id == 0 is valid for “read only” profiles when
profile does not have any “write” commands.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PPP name was going to be confusing since PPP already means point
to point protocol. It is decided to change pipeline personalization
profile(ppp) to dynamic device personalization(ddp).
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Variable read_size is initialized and this value is never read, it is
instead set inside the do-loop, hence the initialization is redundant
and can be removed. Cleans up clang warning:
drivers/net/ethernet/intel/i40e/i40e_nvm.c:390:6: warning: Value stored
to 'read_size' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump the i40e driver from 2.1.14 to 2.3.2.
Bump the i40evf driver from 3.0.1 to 3.2.2
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We introduced the virtchnl interface in order to have an interface for
talking to a virtual device driver which was host-driver agnostic. This
interface has its own definitions, including one for link speed.
The host driver has to talk to the virtchnl interface using these new
definitions in order to remain compatible. Today, the i40e link_speed
enumerations are value-exact matches for the virtchnl interface, so it
was originally decided to simply use a typecast.
However, this is unsafe, and makes it easier for future drivers to
continue this unsafe practice. There is nothing guaranteeing these
values are exact, and the type-cast would hide any compiler warning
which indicates the problem.
Rather than rely on this type cast, introduce a helper function which
can convert the AdminQ link speed definition into a virtchnl
definition. This can then be used by host driver implementations in
order to safely convert to the interface recognized by the virtual
functions.
If the link speed is not able to be represented by the virtchnl
definitions we'll report UNKNOWN which is the safest result.
This will ensure that should the driver specific link_speeds actual bit
definitions change, we do not report them incorrectly according to the
VF.
Additionally, this provides a better pattern for future drivers to copy,
as it is more likely a future device may not use the exact same bit-wise
definition as the current virtchnl interface.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We currently notify a VF of the link state after ENABLE_QUEUES, which is
the last thing a VF does after being configured. Guests may not actually
ENABLE_QUEUES until they get configured, and thus between driver load
and device configuration the VF may show inaccurate link status.
Fix this by also sending the link state after GET_VF_RESOURCES. Although
we could remove the message following ENABLE_QUEUES, it's not that
significant of a loss, so this patch just keeps both to ensure maximum
compatibility with guests on various OSes.
Specifically, without this patch guests running FreeBSD will display
inaccurate link state until the device is brought up. This is mostly
a cosmetic issue but can be confusing to system administrators.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Display some more stats that were already being counted, to help users
understand when priority xon/xoff packets are being sent/received
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver has a special "FDIR" RX-ring (I40E_VSI_FDIR) which is
a sideband channel for configuring/updating the flow director tables.
This (i40e_vsi_)type does not invoke XDP-ebpf code.
As suggested by Björn (V2): Instead of marking this I40E_VSI_FDIR RX-ring
a special case, reverse the logic and only select RX-rings of type
I40E_VSI_MAIN to register xdp_rxq_info's for.
Driver hook points for xdp_rxq_info:
* reg : i40e_setup_rx_descriptors (via i40e_vsi_setup_rx_resources)
* unreg: i40e_free_rx_resources (via i40e_vsi_free_rx_resources)
Tested on actual hardware with samples/bpf program.
V2: Fixed bug in i40e_set_ringparam (memset zero) + match on I40E_VSI_MAIN.
V4: Update patch desc that got out-of-sync with code.
Cc: intel-wired-lan@lists.osuosl.org
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When filter configuration is not supported, drivers should return
-EOPNOTSUPP so the core can react correctly.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, such as with bridging, it is possible that the
stack will add a devices own MAC address to its unicast address list.
If, later, the stack deletes this address, then the i40e driver will
receive a request to remove this address.
The driver stores its current MAC address as part of the MAC/VLAN hash
array, since it is convenient and matches exactly how the hardware
expects to be told which traffic to receive.
This causes a problem, since for more devices, the MAC address is stored
separately, and requests to delete a unicast address should not have the
ability to remove the filter for the MAC address.
Fix this by forcing a check on every address sync to ensure we do not
remove the device address.
There is a very narrow possibility of a race between .set_mac and
.set_rx_mode, if we don't change netdev->dev_addr before updating our
internal MAC list in .set_mac. This might be possible if .set_rx_mode is
going to remove MAC "XYZ" from the list, at the same time as .set_mac
changes our dev_addr to MAC "XYZ", we might possibly queue a delete,
then an add in .set_mac, then queue a delete in .set_rx_mode's
dev_uc_sync and then update netdev->dev_addr. We can avoid this by
moving the copy into dev_addr prior to the changes to the MAC filter
list.
A similar race on the other side does not cause problems, as if we're
changing our MAC form A to B, and we race with .set_rx_mode, it could
queue a delete from A, we'd update our address, and allow the delete.
This seems like a race, but in reality we're about to queue a delete of
A anyways, so it would not cause any issues.
A race in the initialization code is unlikely because the netdevice has
not yet been fully initialized and the stack should not be adding or
removing addresses yet.
Note that we don't (yet) need similar code for the VF driver because it
does not make use of __dev_uc_sync and __dev_mc_sync, but instead roles
its own method for handling updates to the MAC/VLAN list, which already
has code to protect against removal of the hardware address.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original code for __i40e_chk_linearize didn't take into account the
fact that if a fragment is 16K in size or larger it has to be split over 2
descriptors and the smaller of those 2 descriptors will be on the trailing
edge of the transmit. As a result we can get into situations where we didn't
catch requests that could result in a Tx hang.
This patch takes care of that by subtracting the length of all but the
trailing edge of the stale fragment before we test for sum. By doing this
we can guarantee that we have all cases covered, including the case of a
fragment that spans multiple descriptors. We don't need to worry about
checking the inner portions of this since 12K is the maximum aligned DMA
size and that is larger than any MSS will ever be since the MTU limit for
jumbos is something on the order of 9K.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since UDP based filters are not supported via big buffer cloud
filters, remove UDP support. Also change a few return types to
indicate unsupported vs invalid configuration.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding cloud filters could fail for a number of reasons,
unsupported filter fields for example, which fails during
validation of fields itself. This will not result in admin
command errors and converting the admin queue status to posix
error code using i40e_aq_rc_to_posix would result in incorrect
error values. If the failure was due to AQ error itself,
reporting that correctly is handled in the inner function.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
sizeof when applied to a pointer typed expression gives the size of
the pointer.
The proper fix in this particular case is to code sizeof(*vfres)
instead of sizeof(vfres).
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After a reset we rebuild the VSIs which is going to clobber any
promiscuous settings we had before reset. This makes it so that we
restore the promiscuous settings we had before reset.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch allows detection of upcoming core reset in case NIC gets
stuck while performing FLR reset. The i40e_pf_reset() function returns
I40E_ERR_NOT_READY when global reset was detected.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is safe to remove the upper limit of 64 queues on a channel
VSI. The upper bound is determined by the VSI's num_queue_pairs
and gets validated when the queue mapping info through mqprio
interface is subject to bound checking in the driver.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
num_mac should be increased only after the call to i40e_add_mac_filter().
Fixes: 5f527ba962 ("i40e: Limit the number of MAC and VLAN addresses that can be added for VFs")
Signed-off-by: Zijie Pan <zijie.pan@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 96a39aed25 ("i40e: Acquire NVM lock before
reads on all devices") we've used the NVM lock
to synchronize NVM reads even on devices which don't strictly
need the lock.
Doing so can cause a regression on older firmware prior to 1.5,
especially when downgrading the firmware.
Fix this by only grabbing the lock if we're running on an X722
device (which requires the lock as it uses the AdminQ to read
the NVM), or if we're currently running 1.5 or newer firmware.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables tc-flower based hardware offloads. tc flower
filter provided by the kernel is configured as driver specific
cloud filter. The patch implements functions and admin queue
commands needed to support cloud filters in the driver and
adds cloud filters to configure these tc-flower filters.
The classification function of the filter is to direct matched
packets to a traffic class. The hardware traffic class is set
based on the the classid reserved in the range :ffe0 - :ffef.
Match Dst MAC and route to TC0:
prio 1 flower dst_mac 3c:fd:fe:a0:d6:70 skip_sw\
hw_tc 1
Match Dst IPv4,Dst Port and route to TC1:
prio 2 flower dst_ip 192.168.3.5/32\
ip_proto udp dst_port 25 skip_sw\
hw_tc 2
Match Dst IPv6,Dst Port and route to TC1:
prio 3 flower dst_ip fe8::200:1\
ip_proto udp dst_port 66 skip_sw\
hw_tc 2
Delete tc flower filter:
Example:
Flow Director Sideband is disabled while configuring cloud filters
via tc-flower and until any cloud filter exists.
Unsupported matches when cloud filters are added using enhanced
big buffer cloud filter mode of underlying switch include:
1. source port and source IP
2. Combined MAC address and IP fields.
3. Not specifying L4 port
These filter matches can however be used to redirect traffic to
the main VSI (tc 0) which does not require the enhanced big buffer
cloud filter support.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce the cloud filter data structure and cleanup of cloud
filters associated with the device.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new admin queue definitions and extended fields for cloud
filter support. Define big buffer for extended general fields
in Add/Remove Cloud filters command.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add definitions for L4 filters and switch modes based on cloud filters
modes and extend the set switch config command to include the
additional cloud filter mode.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add mapping of TCs with the seids of the channel VSIs. TC0
will be mapped to the main VSI seid and all other TCs are
mapped to the seid of the corresponding channel VSI.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 11f29003d6.
I am reverting this as I am fairly certain this can result in a memory leak
when combined with the current page recycling scheme. Specifically we end
up attempting to allocate fewer buffers than we recycled and this results
in us rewinding the next to alloc pointer which leads to leaks when we
overwrite the rx_buffer_info when processing the next frame.
Fixes: 11f29003d6 ("i40e/i40evf: bump tail only in multiples of 8")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whether or not there are vectors_left, we only need to redistribute
our vectors if we didn't get as many as we requested. With the current
check, the code will try to redistribute even if we did in fact get all
the vectors we requested - this can happen when we have more CPUs than
we do vectors. This restores an earlier check to be sure we only
redistribute if we didn't get the full count we requested.
Fixes: 4ce20abc64 (i40e: fix MSI-X vector redistribution if hw limit is reached)
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A cleanup of the PM code left an incorrect #ifdef in place, leading
to a harmless build warning:
drivers/net/ethernet/intel/i40e/i40e_main.c:12223:12: error: 'i40e_resume' defined but not used [-Werror=unused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:12185:12: error: 'i40e_suspend' defined but not used [-Werror=unused-function]
It's easier to use __maybe_unused attributes here, since you
can't pick the wrong one.
Fixes: 0e5d3da400 ("i40e: use newer generic PM support instead of legacy PM callbacks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the i40e driver to include programming descriptors in
the cleaned_count. Without this change it becomes possible for us to leak
memory as we don't trigger a large enough allocation when the time comes to
allocate new buffers and we end up overwriting a number of rx_buffers equal
to the number of programming descriptors we encountered.
Fixes: 0e626ff7cc ("i40e: Fix support for flow director programming status")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It looks like there was either a copy/paste error or just a typo that
resulted in the Tx ITR setting being used to determine if we were using
adaptive Rx interrupt moderation or not.
This patch fixes the typo.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
