Fix warnings with W=1
If these variables are useful this driver should be modified to expose
them.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix warnings with W=1
If these variables are useful then this driver should be modified to
expose them.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No reason why this is global, fix warnings with W=1
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AK4497 is a 32-bit 2ch DAC and has the same register
map as AK4458 with few exceptions:
* AK4497 has one more register at the end of register space
DFS_READ which is a read only register that allows users
to read FS Auto Detection mode. We currently do not use
this register so we use the same regmap structure as for ak4458.
* Because AK4458 is an 8ch DAC there are some fields that are
only used by AK4458 and marked as reserved for AK4497, so for
this reason we need to have a distinct set of controls, widgets
and routes.
Datasheet for AK4497 is at:
https://www.akm.com/akm/en/file/ev-board-manual/AK4497EQ.pdf
Datasheet for AK4458 is at:
https://www.akm.com/akm/en/file/datasheet/AK4458VN.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Export the DAC functionality to mix left + right together and then output
the same (mixed) signal on both outputs.
Various (x86) tablets with an ES8316 codec use a single speaker
connected between the headhpone LOUT and ROUT pins, expecting the output
to be in a mono differential mode. Presumably this is done to use the
power of both the left and right outputs to allow the speaker to be
louder.
The ES8316 codec does not have a differential output mode, but we can
emulate this by making both channels output the same through the mono mix
switch, combined with setting the Playback Polarity control to "R Invert",
which applias a 180 degrees phase inversion to the right channel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding jack-detect support may seem weird for a codec with only
a single output, but it is necessary. The ES8316 appnote showing
the intended usage uses a jack-receptacle which physically disconnects
the speakers from the output when a jack is plugged in.
But all 3 devices using the es8316 which I have (2 Cherry Trail
devices and one Bay Trail CR device), use an analog mux to disconnect
the speakers, driven by a GPIO. In order to enable/disable the speakers
at the right time, we need jack-detect.
The same goes for the microphone where we must correctly set the mux
for the single ADC to either the internal or the headset microphone.
All devices I have support the es8316's builtin jack-detect functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Inside function rt274_i2c_probe(), if regmap_read() function
returns -EINVAL, then local variable "val" leaves uninitialized
but used in if statement. This is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds reset and precharge in shutdown of PCM device.
ACODEC goes to silence if we change Fs to 44.1kHz from 48kHz. This
workaround seems to work but I don't know this workaround is correct
sequence or not for ACODEC.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for audio CODEC core of rk3328.
Rockchip does not publish detail specification of this core
but driver source code is opened on their GitHub repository.
https://github.com/rockchip-linux/kernel
So I ported this code to linux-next and added some trivial fixes.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
MCLK input is needed when accessing any register after enabling SYSCLK.
This also fixes imbalance of clk_enable / clk_disable when transitioning
between ON -> STANDBY -> ON bias levels.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Save 2x unsigned int of .rodata.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For platforms that use the audio-graph-card driver, the codec is
not selected by SoC-platform driver. Make it available.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Cirrus Logic CS4341.
This is a very simple, playback only, stereo DAC.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADC mixer setting needs to restore to default value
after calibration.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We accidentally call mutex_unlock(&pcm512x->mutex); twice in a row.
I re-wrote the error handling to use "goto unlock;" instead of returning
directly. Hopefully, it makes the code a little simpler.
Fixes: 3500f1c589 ("ASoC: pcm512x: Implement the digital_mute interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviwed-by: Dimitris Papavasiliou <dpapavas@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not much work on the core this time around but we've seen quite a bit of
driver work, including on the generic DT drivers. There's also a large
part of the diff from a merge of the DaVinci and OMAP directories, along
with some active development there:
- Preparatory work from Morimoto-san for merging the audio-graph and
audio-graph-scu cards.
- A merge of the TI OMAP and DaVinci directories, the OMAP product line
has been merged into the DaVinci product line so there is now a lot
of IP sharing which meant that the split directories just got in the
way. This has pulled in a few architecture changes as well.
- A big cleanup of the Maxim MAX9867 driver from Ladislav Michl.
- Support for Asahi Kaesi AKM4118, AMD ACP3x, Intel platforms with
RT5660, Meson AXG S/PDIF inputs, several Qualcomm IPs and Xilinx I2S
controllers.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwY7KsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MFqB/4m9nlfUeXTpiSD1FgVIlMmdPNUg4V2
6Ybztaw4kRc5LuQN8PXQmaFLx020yAnLvI7Zzj7l3K8r6a9lfyFs+pKL0wtBnNK2
9QEFmOVQ3QFpt31Yb2IQeO4dfNbiyKeczjLau4mXWTl0j5dc/UH+HasE1dRZOxsC
rqJ8IsdibIVxVtQ7ZmcnU+y6XK0inBHAAh6ksMehsufShGrfrLs/nRBaXRZcRqJg
ciSFY5uYRYkDxTgogTpNRfVy4nr17N10+0sgrQ3RtaaqgG3gBXsHca1meyxKYW3Q
TssOJGIl3+uGiAMNyZqzxe5pAwwuGhZ3hAAAODtfYJQtAuAOW3/45Wqh
=phWF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.21
Not much work on the core this time around but we've seen quite a bit of
driver work, including on the generic DT drivers. There's also a large
part of the diff from a merge of the DaVinci and OMAP directories, along
with some active development there:
- Preparatory work from Morimoto-san for merging the audio-graph and
audio-graph-scu cards.
- A merge of the TI OMAP and DaVinci directories, the OMAP product line
has been merged into the DaVinci product line so there is now a lot
of IP sharing which meant that the split directories just got in the
way. This has pulled in a few architecture changes as well.
- A big cleanup of the Maxim MAX9867 driver from Ladislav Michl.
- Support for Asahi Kaesi AKM4118, AMD ACP3x, Intel platforms with
RT5660, Meson AXG S/PDIF inputs, several Qualcomm IPs and Xilinx I2S
controllers.
Clicks and pops of various volumes can be produced while the device is
opened, closed, put into and taken out of standby, or reconfigured.
Fix this, by implementing the digital_mute interface, so that the
output is muted during such operations.
Signed-off-by: Dimitris Papavasiliou <dpapavas@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The display power is in unbalance at removing the driver since it
misses the snd_hdac_display_power(OFF) call.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After the recent refactoring, snd_hdac_display_power() doesn't return
any error, hence it can be defined to return void.
This makes many error checks redundant and allows us to reduce them
gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current HD-audio code manages the DRM audio power via too complex
redirections, and this seems even still unbalanced in a corner case as
Intel DRM CI has been intermittently reporting. This patch is a big
surgery for addressing the complexity and the possible unbalance.
Basically the patch changes the display PM in the following ways:
- Both HD-audio controller and codec drivers call a single helper,
snd_hdac_display_power(). (Formerly, the display power control from
a codec was done indirectly via link_power bus ops.)
- snd_hdac_display_power() receives the codec address index. For
turning on/off from the controller, pass HDA_CODEC_IDX_CONTROLLER.
- snd_hdac_display_power() doesn't manage refcounts any longer, but
keeps the power status in bitmap. If any of controller or codecs is
turned on, the function updates the DRM power state via get_power()
or put_power().
Also this refactor allows us more cleanup:
- The link_power bus ops is dropped, so there is no longer indirect
management, as mentioned in the above.
- hdac_device link_power_control flag is moved to hda_codec
display_power_control flag, as it's only for HDA legacy.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106525
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Driver rewritten, assign copyright notice and change module author
as original one remains silent and I want to be notified about bugs.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sound capture and line bypass currently do not work as well as
some mixer controls. Fix that by building proper audio paths and
adjusting volume controls to match datasheet.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop "Common NI Values Table" and calculate LRCLK divider, then
add allowed rate constraints based on master clock frequency.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement set_bias_level to drive shutdown bit, so device is
put to sleep when unused.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Realtek codec ALC3277 is 100% compatible with the codec RT5660
in I2S mode. And on the Dell IoT platform, the codec is ALC3277,
and the HID of the codec in the BIOS is 10EC3277, so adding this
ID to the ACPI match table.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Get the reset GPIO through the GPIO consumer API. This allows specifying the
DT property as "reset-gpios" without breaking existing DT users.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Get the reset GPIO through the GPIO consumer API. This allows specifying the
DT property as "reset-gpios" without breaking existing DT users.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch added max98373_reset function to avoid amp software reset failure and code duplication.
Reset verification step has been added for stable amp reset and it repeats verification maximum 3 times when it is failed.
Chip revision ID is available when the amp is in the idle state which means software reset is completed well.
Additional 10ms delay was added for every retrial and maximum 30ms delay can be applied.
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suffix ULL to constant 256 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
256 * fs * 2 * mclk_src_scaling[i].param
Signed-off-by: Young_X <YangX92@hotmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introducing a module param for wakeup_delay in order to
align with modeswitch_delay parameter. With this change, both
wakeup_delay and modeswitch_delay parameters can be passed
as module parameters.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On startup, applications such as PulseAudio or CRAS enable playback or
capture on all PCM devices to verify that configurations are correct,
and close them immediately. For DMICs, this can result in the clock
being turned off very quickly, which may not compatible with internal
state machine transition requirements.
This patch add a mode-switch delay which will prevent the clock from
being turned off without complying with manufacturer timing
specifications. While the DMIC clock may be controlled at a lower level,
be it with hardware or firmware, applying the delay during the
STOP_TRIGGER phase ensures that there is no race condition, e.g. with
the hardware/firmware turning off the clock earlier
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lots of fixes here, the majority of which are driver specific but
there's a couple of core things and one notable driver specific one:
- A core fix for a DAPM regression introduced during the component
refactoring, we'd lost the code that forced a reevaluation of the
DAPM graph after probe (which we suppress during init to save lots
of recalcuation) and have now restored it.
- A core fix for error handling using the newly added
for_each_rtd_codec_dai_rollback() macro.
- A fix for the names of widgets in the newly introduced pcm3060
driver, merged as a fix so we don't have a release with legacy names.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlv9WBQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0KeSB/9mrVVRe8hVg2ErfCEY8BaPGIdtNoBT
IIRh/woXwbZEsY3owRuF5FeQxUbsRWLQL8fnzLFE7b6ltlRiPKahIGG0rIE0Xqcz
jkvqR0Kvck1MLNjj8qyd72Eqv0uQmW5qoezY9eFJiWms5uIlbh+WR3KPFu4WkcnD
9DHoYYq4ZU3EIqgt92QJ2uOWPwrSfueBcz6+bdYy11mSMuUtHz4HaAV8/XGFEjFy
9uPeNmS4nTFxGXR5PzpxTP1mG7nYixq3J07iwXGTH/X3LDANmJCPgMgQQRnY6h1k
KrtnZfcNljJxyYuNPV/A3ShG98Snbym17cq2zN1o9ZBUlPyxfGdRwrTd
=NoTQ
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.20-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.20
Lots of fixes here, the majority of which are driver specific but
there's a couple of core things and one notable driver specific one:
- A core fix for a DAPM regression introduced during the component
refactoring, we'd lost the code that forced a reevaluation of the
DAPM graph after probe (which we suppress during init to save lots
of recalcuation) and have now restored it.
- A core fix for error handling using the newly added
for_each_rtd_codec_dai_rollback() macro.
- A fix for the names of widgets in the newly introduced pcm3060
driver, merged as a fix so we don't have a release with legacy names.
Amplifier may have assosicated regulator, so add a widget for it
and appropriate route.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec can support any variation of bclk/fs master/slave configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default implementation of regulator_set_load returns
REGULATOR_MODE_NORMAL, which is positive. [This was a bug which is
being fixed but the change is valid anyway -- bronie]
rt5663_i2c_probe should only do error handling when return value of
regulator_set_load is negative.
In this case, rt5663_i2c_probe should return error.
Also, consolidate err_irq into err_enable.
Fix the missing goto for temporary regmap and rt5663->regmap.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return statement is indented incorrectly. Fix this by adding in
the missing tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The goto statement is indented too much by one level, fix this by
removing the extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return statement is indented too much by one level, fix this by
removing an extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator support to turn on cpvdd and avdd in probe.
If a regulator is not given from device tree, a dummy regulator will be
used.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AK4118A is a digital audio transceiver supporting 8 input channels
at 192kHz and with 24bits resolution.
It converts the S/PDIF signal to I2S format and is configurable over I2C.
This driver introduce a minimal support of the AK4118, like selecting the
input channel, reading input frequency and detecting some errors.
Datasheet is available here:
https://www.akm.com/akm/en/file/datasheet/AK4118AEQ.pdf
Signed-off-by: Adrien Charruel <adrien.charruel@devialet.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the current device datasheet (TI Lit # SLAS831D, revised
March 2018) the value written to the device's PAGE register to trigger
a complete register reset should be 0xfe, not 0xff. So go ahead and
update to the correct value.
Reported-by: Stephane Le Provost <stephane.leprovost@mediatek.com>
Tested-by: Stephane Le Provost <stephane.leprovost@mediatek.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch updates license to SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: David Lin <CTLIN0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAC output may be differential (default) or single-ended.
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the initial commit [1], I added differential output of the codec as
separate `+` and `-` widgets:
OUTL+
OUTR+
OUTL-
OUTR-
Later, in the commit [2], I added a device tree property to configure the
output as single-ended or differential. Having this property, the `+` and
`-` separation in widgets seems for me confusing. There are no functional
benefits in such separation, so I find reasonable to get rid of it:
OUTL
OUTR
The new naming is more friendly for sound cards, and is better aligned with
other codec drivers in kernel.
Renaming the output widgets now should not be a problem from the backwards-
compatibility perspective, as the driver for PCM3060 is added into the
mainline very recently, and did not yet appear in any releases.
[1] commit 6ee47d4a8d ("ASoC: pcm3060: Add codec driver")
[2] commit a78c62de00d5 ("ASoC: pcm3060: Add DT property for single-ended
output")
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
On certain platforms, Display HDMI HDA codec was not going to sleep state
after the use when links are powered down after turning off the display
power. As per the HW recommendation, links are powered down before turning
off the display power to ensure that the codec goes to sleep state.
This patch was updated from an earlier version submitted upstream [1]
which conflicted with the changes merged for HDaudio codec support
with the Intel DSP.
[1] https://patchwork.kernel.org/patch/10540213/
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Icelake device id. Also, Icelake's pin2port mapping table is
complicated. So we use a mapping table to do the pin2port mapping.
Signed-off-by: Bard liao <bard.liao@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Factor out the duplicated initialization statements from
wm_adsp1_init() and wm_adsp2_init() into new function
wm_adsp_common_init().
The entire content of wm_adsp1_init() is the common code
but it is convenient to retain this exported function
to hide what we currently treat as common init (which might
change in the future) and also make clear the difference
between an ADSP1 entry point and common code.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stack memory isn't DMA-safe so it isn't safe to use either
regmap_raw_read or regmap_bulk_read to read into stack memory.
The two functions to read the scratch registers were using
stack memory and regmap_raw_read. It's not worth allocating
memory just for this trivial read, and it isn't time-critical.
A simple regmap_read for each register is sufficient.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DACn Zero Flag" and "ADCn Overflow Flag" are read-only status
register. These information are needed for driver not for user.
Let's remove these from snd_kcontrol_new.
There is no detail explanation for these register on
datasheet, but, judging from its behavior, it seems these register
needs clock to read. Otherwise, I2C returns error.
Therefor, amixer command will be failed under non working timing.
Without this patch, user often fail amixer command.
This patch is tested on R-Car H3 ulcb-kf board, SSI3/4 TDM sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_component_update_bits() will only update the mask bits,
so remove the redundant snd_soc_component_read32().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
hw constraint for LEFT_J/I2S are same, but had duplicated code.
This code cleanup these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures are only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structures
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
WARN_ON() already contains an unlikely(), so it's not necessary to use
unlikely.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gcc notices that without either the ac97 bus or the pdata, we never
initialize the regmap pointer, which leads to an uninitialized variable
access:
sound/soc/codecs/wm9712.c: In function 'wm9712_soc_probe':
sound/soc/codecs/wm9712.c:666:2: error: 'regmap' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Since that configuration is invalid, it's better to return an error
here. I tried to avoid adding complexity to the conditions, and turned
the #ifdef into a regular if(IS_ENABLED()) check for readability.
This in turn requires moving some header file declarations out of
an #ifdef.
The same code is used in three drivers, all of which I'm changing
the same way.
Fixes: 2ed1a8e0ce ("ASoC: wm9712: add ac97 new bus support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There have been little changes in ALSA core stuff, but ASoC core still
kept rolling for the continued restructuring. The rest are lots of
small driver-specific changes and some minor API updates.
Here are highlights:
General:
- Appropriate fall-through annotations everywhere
- Some code cleanup in memalloc code, handling non-cacahed pages more
commonly in the helper
- Deployment of SNDRV_PCM_INFO_SYNC_APPLPTR flag consistently
Drivers:
- More HD-audio CA0132 codec improvement for supporting other Creative
boards
- Plumbing legacy HD-audio codecs as ASoC BE on Intel SST; this will
give move support of existing HD-audio devices with DSP
- A few device-specific HD-audio quirks as usual
- New quirk for RME CC devices and correction for B&W PX for USB-audio
- FireWire: code refactoring including devres usages
ASoC Core:
- Continued componentization works; it's almost done!
- A bunch of new for_each_foo macros
- Cleanups and fixes in DAPM code
ASoC Drivers:
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060
-----BEGIN PGP SIGNATURE-----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=3LrT
-----END PGP SIGNATURE-----
Merge tag 'sound-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There have been little changes in ALSA core stuff, but ASoC core still
kept rolling for the continued restructuring. The rest are lots of
small driver-specific changes and some minor API updates. Here are
highlights:
General:
- Appropriate fall-through annotations everywhere
- Some code cleanup in memalloc code, handling non-cacahed pages more
commonly in the helper
- Deployment of SNDRV_PCM_INFO_SYNC_APPLPTR flag consistently
Drivers:
- More HD-audio CA0132 codec improvement for supporting other Creative
boards
- Plumbing legacy HD-audio codecs as ASoC BE on Intel SST; this will
give move support of existing HD-audio devices with DSP
- A few device-specific HD-audio quirks as usual
- New quirk for RME CC devices and correction for B&W PX for USB-audio
- FireWire: code refactoring including devres usages
ASoC Core:
- Continued componentization works; it's almost done!
- A bunch of new for_each_foo macros
- Cleanups and fixes in DAPM code
ASoC Drivers:
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060"
* tag 'sound-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (299 commits)
ASoC: stm32: sai: fix master clock naming
ASoC: stm32: add clock dependency for sai
ALSA: hda/ca0132 - Actually fix microphone issue
ASoC: sun4i-i2s: move code from startup/shutdown hooks into pm_runtime hooks
ASoC: wm2000: Remove wm2000_read helper function
ASoC: cs42l51: fix mclk support
ASoC: wm_adsp: Log addresses as 8 digits in wm_adsp_buffer_populate
ASoC: wm_adsp: Rename memory fields in wm_adsp_buffer
ASoC: cs42l51: add mclk support
ASoC: stm32: sai: set sai as mclk clock provider
ASoC: dt-bindings: add mclk support to cs42l51
ASoC: dt-bindings: add mclk provider support to stm32 sai
ASoC: soc-core: fix trivial checkpatch issues
ASoC: dapm: Add support for hw_free on CODEC to CODEC links
ASoC: Intel: kbl_da7219_max98927: minor white space clean up
ALSA: i2c/cs8427: Fix int to char conversion
ALSA: doc: Brush up the old writing-an-alsa-driver
ASoC: rsnd: tidyup SSICR::SWSP for TDM
ASoC: rsnd: enable TDM settings for SSI parent
ASoC: pcm3168a: add hw constraint for capture channel
...
The return type "unsigned int" was used by the wm2000_read()
function despite of the aspect that it will eventually return
a negative error code.
The resulting function doesn't add much to the code, so replace
wm2000_read with regmap_read.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MCLK clock is made optional for cs42l51 codec.
However, ASoC DAPM clock supply widget, expects the clock to be defined
unconditionally.
Register MCLK DAPM conditionally in codec driver,
depending on clock presence in DT.
Fixes: 5e8d63a726 ("ASoC: cs42l51: add mclk support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Increase the address value width in the debug log from 4 digits to
8 digits to allow for DSP cores with larger memory address ranges.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm_adsp_buffer struct is the control header of a circular
buffer used to transfer data from the firmware over the
control interface to an ALSA compressed stream.
The original names of the fields pointing to the data buffer
were based on ADSP2V2 memory layout where they correspond to
{XM, XM, YM}. But this circular buffer could be used on other
types of DSP core that have different memory region types.
Also the names and description of the size fields were not
very clear. The field names and descriptions have been changed
to be generic and not imply any particular memory types.
This patch updates the wm_adsp driver to the new field names.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add MCLK dapm to allow configuration of cirrus CS42l51
codec as a master clock consumer.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LEFT_J / I2S only can use TDM.
commit 594680ea4a ("ASoC: pcm3168a: add hw constraint for channel")
commit 3809688980 ("ASoC: pcm3168a: add HW constraint for non
RIGHT_J") added channel constraint for it, but, it was only for playback.
This patch adds constraint for capture.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The STA32x chips feature an XTI clock input that needs to be stable before
the reset signal is released. Therefore, the chip driver needs to get a
handle to the clock. Instead of relying on other parts of the system to
enable the clock, let the codec driver grab a handle itself.
In order to keep existing boards working, clock support is made optional.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
pcm3168a is supporting TDM on I2S/Left_J, but there is no
settings for it. This patch add it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LEFT_J / I2S only can use TDM.
This patch adds channel constraint for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RIGHT_J only can handle 16bit data bits.
Current driver just errored if user requests non RIGHT_J
+ 16bit combination. But it is not useful for user.
This patch adds HW constraint for it, and avoid
error on such situation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
max98988 only builds with I2C support enabled, otherwise we get a build error:
sound/soc/codecs/max98088.c:1789:1: error: data definition has no type or storage class [-Werror]
module_i2c_driver(max98088_i2c_driver);
^~~~~~~~~~~~~~~~~
sound/soc/codecs/max98088.c:1789:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
sound/soc/codecs/max98088.c:1789:1: error: parameter names (without types) in function declaration [-Werror]
sound/soc/codecs/max98088.c:1780:26: error: 'max98088_i2c_driver' defined but not used [-Werror=unused-variable]
Fixes: 24ae67c582 ("ASoC: max98988: make it selectable")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver will build only if SND_SOC_ALL_CODECS is set.
Adding a Kconfig menu description to build the driver standalone.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If master clock is provided through device tree, then update
the master clock frequency during set_sysclk.
Cc: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[m.felsch@pengutronix.de: move mclk request to i2c_probe]
[m.felsch@pengutronix.de: make use of snd_soc_component_get_bias_level()]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lookup regulators for Vdd and Vdda during probe, and enable them when the
component is linked.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotations in rt274 driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation.
Unfortunately gcc doesn't understand the mixed comment lines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation
at the right place. It has to be put right before the next label.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver already has support for setting the FDRB bit in the CONFA
register through platform data, but there was no property to set it
in the device-tree bindings.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'ret' variable is now only used in an #ifdef, and causes a
warning if it is declared outside of that block:
sound/soc/codecs/wm9712.c: In function 'wm9712_soc_probe':
sound/soc/codecs/wm9712.c:641:6: error: unused variable 'ret' [-Werror=unused-variable]
Fixes: 2ed1a8e0ce ("ASoC: wm9712: add ac97 new bus support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAX98088 is an older version of the MAX98089 device.
Signed-off-by: Andreas Färber <afaerber@suse.de>
[m.felsch@pengutronix.de: add CONFIG_OF compile switch]
[m.felsch@pengutronix.de: adapt commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cs4265 driver is missing a microphone preamp enable.
This patch enables/disables the microphone preamp when mic
selection is made using the kcontrol.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch removes the boost volume in the beginning of playback while the
DAC volume set to lower.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be more readable code, this patch adds
new for_each_card_rtds() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This SPI driver does not use the legacy GPIO header so
just delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Minor code changes are:
- improve the readability in patch list
- add i2c remove function
- regmap_register_patch changes to regmap_multi_reg_write
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixed the boost volume at the begining of playback
while DAC volume set to lower level.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADC/DAC path should open while calibration process.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removed Headphone Playback Volume control.
Due to codec settings, we don't want the user to change HP analog gain.
The user could use DAC1 Playback Volume control to
change playback volume.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We change the settings while HP power-up for better performance.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
module.h already contained moduleparam.h, so it is safe to remove
the redundant include.
The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The value of period_bytes will get the zero before the hw_params() is not
run completely. Move the function snd_pcm_lib_period_bytes() to copy work,
and make sure that is not zero.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the usual set of small fixes scatterd around various drivers,
plus one fix for DAPM and a UAPI build fix. There's not a huge amount
that stands out here relative to anything else.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluf2AQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BojB/9ZpiRgSSjKTFSmGgu3OFI7Nvj63ruB
hxOnwOc8Bea8tZtpzgEcx/aLZ1sbWVT4uRUYZv0Tf6UJtuOQagbJDEUkUdRitKtX
1khSMyKFlAa7cIbv19ZOMCN0pjcs7hlHCPryT8AyCWCWN8yPdlUsDqWfyfUoq56r
qpdu/OQ4E9VvS8OcX1gPjcop3gE/fYEoU+mbUpr0KYUXaroEzJm85tOqpGYk4+XW
GCNUR19vNRJr5G6ANqIx96JOlgF5nRZu7aOfvLceiWH5BgPdW3iNRAJkPmKCIHwb
a1+X21eCC7Ec2/7bQmR5Aoxz1yqzhngrevSFNLrqXFZmMmNrEfkfdCrJ
=gVzO
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.19
This is the usual set of small fixes scatterd around various drivers,
plus one fix for DAPM and a UAPI build fix. There's not a huge amount
that stands out here relative to anything else.
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5668_i2c_remove() is empty, and no longer needed.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MMTLR bit is in the CS4265_SPDIF_CTL2 register at address 0x12 bit 0
and not at address 0x0 bit 1. Fix this.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit ca917f9fe1 added use of usleep_range() but not
the corresponding "include <linux/delay.h>". The result is
with Chrome OS won't build because warnings are forced
to be errors:
mnt/host/source/src/third_party/kernel/v4.4/sound/soc/codecs/max98373.c:734:2: error: implicit declaration of function 'usleep_range' [-Werror,-Wimplicit-function-declaration]
usleep_range(10000, 11000);
^
Including delay.h "fixes" this.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Playback of 44.1Khz contents with HDMI plugged returns
"Invalid pipe config" because HDMI paths in the FW
topology are configured to operate at 48Khz.
This patch filters out sampling rates not supported
at hdac_hdmi_create_dais() to let user space SRC
to do the converting.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case where lo_vag <= SGTL5000_LINE_OUT_GND_BASE, lo_vag
is set to zero and later vol_quot is computed by dividing by
lo_vag causing a division by zero error. Fix this by avoiding
a zero division and set vol_quot to zero in this specific case
so that the lowest setting for i is correctly set.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The !port check is redundant as it being performed in the following
check. Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar to short circuit detection, when the ADC/DAC is saturated and
overflows poor audio quality can result and should be reported to the
user. This device support Automatic Dynamic Range Compression (DRC)
to reduce this but it is not enabled currently in this driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These devices support detecting and reporting short circuits across
the output stages. Add support for reporting these issue. Do this
by registering an interrupt if available and enabling this error
to trigger that interrupt in the device.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TAS6426 has a register that reports channel faults such as
overcurrent and continuous DC output. Add reporting of this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When there is no fault bit set in a fault register we skip the fault
reporting section for that register. This also skips over saving that
registers value. We save the value so we will not double report an
error, but if an error clears then returns we will also not report it
as we did not save the all cleared register value. Fix this by saving
the fault register value in the all clear path.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The current short version of the register name may be
ambiguous when another fault register detection is added.
Use the full name.
While here fix comment about clearing faults, the CLEAR_FAULT
register actually only clears sticky bits, which are only
warnings, fault bits can only cleared by resolving the fault.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a S/PDIF enable switch as a SOC_SINGLE.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cs4265 uses 32 bit transport on the I2S bus. This patch enables native
32 bit mode for machine drivers which use this sound card driver.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cs4265 driver declares the "MMTLR Data Switch" register setting with
a 0 register value rather then the 0x12 register (CS4265_SPDIF_CTL2).
This incorrect value causes alsamixer to fault with the output :
cannot load mixer controls: Input/output error
This patch corrects the register value. alsamixer now runs.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike the TAS5720, the TAS5722 can be configured to utilize 16-bit wide
slots in TDM mode. This can help easing audio clocking/frequency
requirements.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TAS5722 supports modifying volume in 0.25dB steps (as opposed to
0.5dB steps on the TAS5720). Introduce a custom mixer control that
allows taking advantage of this finer output volume granularity.
Also add custom getters/setters for access as the TAS5722 digital volume
controls are split over two registers.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before this patch the only alias provided by the dmic module is:
alias: platform:dmic-codec
Device instantiated from DT will not probe automatically with this
After this patch, here is the new alias list:
alias: platform:dmic-codec
alias: of:N*T*Cdmic-codecC*
alias: of:N*T*Cdmic-codec
Now the dmic codec probes automatically when instantiated from DT.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Kconfig prompt for the generic digital mic to make it configurable
through menuconfig
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
adau17x1_setup_firmware and adau17x1_has_dsp is only used internally, so
making them static instead of exported.
Signed-off-by: Robert Rosengren <robertr@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modified some if-statements to make them more clear
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modified the complete file comments in C++ style, to make them look more
intentional
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds support for TI PCM3060 CODEC.
The technical documentation is available at [1].
[1] http://ti.com/product/pcm3060
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: M R Swami Reddy <mr.swami.reddy@ti.com>
Cc: Vishwas A Deshpande <vishwas.a.deshpande@ti.com>
Cc: Kevin Cernekee <cernekee@chromium.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Thinkpad 8 needs a quirk for jack-detect and the internal mic to
work correctly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Safeload support has been implemented which is used
when updating for instance filter parameters using
alsa controls. Without safeload support audio can
become distorted during update.
Signed-off-by: Danny Smith <dannys@axis.com>
Signed-off-by: Robert Rosengren <robertr@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed range in safeload conditional to allow safeload to up to 20 bytes,
without a lower limit.
Signed-off-by: Danny Smith <dannys@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a kernel module which is used by the legacy HDA
codec drivers as library. This implements hdac_ext_bus_ops to enable
the reuse of legacy HDA codec drivers with ASoC platform drivers.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HID made of either Wolfson/CirrusLogic PCI ID + 8804 identifier.
This helps enumerate the HifiBerry Digi+ HAT boards on the Up2 platform.
The scripts at https://github.com/thesofproject/acpi-scripts can be
used to add the ACPI initrd overlays.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
New calibration sequence allows rt5682 do calibration without
MCLK.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The step of DAC/ADC volume scale changes from 0.375dB to 0.75dB
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
After our evaluation, we need to modify the default values to make sure
the volume applied immediately.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 143b44845d ("ASoC: wm9712: replace codec to component")
"wm9712-codec" got renamed to "wm9712-component", however, this change
never got propagated down to the actual board/platform drivers. E.g. on
Colibri T20 this lead to the following spew upon boot with sound/touch
being broken:
[ 2.214121] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 2.222137] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 2.344384] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 2.351885] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 2.668339] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 2.675811] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 3.208408] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 3.216312] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 3.235397] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 3.248938] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 14.970443] ALSA device list:
[ 14.996628] No soundcards found.
This commit finally fixes this again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
A fairly big update, including quite a bit of core activity this time
around (which is good to see) along with a fairly large set of new
drivers.
- A new snd_pcm_stop_xrun() helper which is now used in several
drivers.
- Support for providing name prefixes to generic component nodes.
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing.
- Generalization of the DIO2125 support to a simple amplifier driver.
- Accessory detection support for the audio graph card.
- DT support for PXA AC'97 devices.
- Quirks for a number of new x86 systems.
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltxVZsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0CtwB/0U+IUWLlojWD6RDfueycvc9TiZW0t4
gBT3OD8f4oif0MuMy6oE2ag8JPNU8n5MnO14U366GDaEyZPj79W7f50Q8Nnyht/n
py6fQfyo7Ec2hFJstDI42KvDymTbAer6hnAUJarr/FdZHdGeOfYV+s7aHp5aEQAS
KACnX8qWo87VePouNBorqWXWueAJTb6zpWy7YQ1KGb/pJIAeue2Y9pLRGXQos1BS
E1AP+ge2BMnz7BeiCgw/39hN6X545nJ1fcZKuIu8Gqy9ahqEDHgmBWPAehtGnfVj
D8JPplTaBFtAsJwi18b7ApWtcytpizPPN/l3NTA4fTRJQe9kxfDmnE7b
=fvKX
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.19
A fairly big update, including quite a bit of core activity this time
around (which is good to see) along with a fairly large set of new
drivers.
- A new snd_pcm_stop_xrun() helper which is now used in several
drivers.
- Support for providing name prefixes to generic component nodes.
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing.
- Generalization of the DIO2125 support to a simple amplifier driver.
- Accessory detection support for the audio graph card.
- DT support for PXA AC'97 devices.
- Quirks for a number of new x86 systems.
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707.
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056531 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms it has been noted that a pop noise can be
witnessed when capturing audio, mainly for first time after a
headset jack has been inserted. This is due to a DC offset in the
Mic PGA and so to avoid this delays are required when powering
up the capture path.
This commit rectifies the problem by adding delays post Mic PGA and
post Mixin PGA. The post Mic PGA delay is determined based on
Mic Bias voltage, and is only applied the first time after a
headset jack is inserted.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of harcoding that a core must always be called "DSPn"
add a name member to struct wm_adsp so that the owning codec
driver can provide a custom name. This allows for re-use of
the wm_adsp driver with parts where the processing cores are
named differently.
If no name is provided the default DSPn name is used.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To allow for more flexibility in naming of DSP-type cores
move the creation of the firmware controls to the codec
drivers instead of having a hardcoded list in wm_adsp.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset of the DSP core needs to be taken into account for the DSP
preloader control get and put. Currently the dsp->preloaded variable
will only ever be read/updated on the first DSP, whilst this doesn't
affect the operation of the control the readback will be incorrect.
Signed-off-by: Ajit Pandey <ajit.pandey@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The driver expects to find the device id in rt5677_of_match.data, however
it is currently assigned to rt5677_of_match.type. Fix this.
The problem was found with the help of clang:
sound/soc/codecs/rt5677.c:5010:36: warning: expression which evaluates to
zero treated as a null pointer constant of type 'const void *'
[-Wnon-literal-null-conversion]
{ .compatible = "realtek,rt5677", RT5677 },
^~~~~~
Fixes: ddc9e69b9d ("ASoC: rt5677: Hide platform data in the module sources")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing break statement in order to prevent the code from falling
through to the default case.
Addresses-Coverity-ID: 115050 ("Missing break in switch")
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115050 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1357430 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115045 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115043 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 146354 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115042 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115041 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115047 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1271174 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056547 ("Missing break in switch")
Addresses-Coverity-ID: 1056548 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1271173 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit e57d4ca882 (ASoC: wcd9335: add support to wcd9335
codec) due to build failures caused by missing dependencies.
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit c8cb5f775c (ASoC: vert "ASoC: wcd9335: add
CLASS-H Controller support) due to missing dependencies.
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable osrate is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'osrate' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CLASS-H controller/Amplifier is common accorss Qualcomm WCD codec series.
This patchset adds basic CLASS-H controller apis for WCD codecs after
wcd9335 to use.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm WCD9335 Codec is a standalone Hi-Fi audio codec IC,
It supports both I2S/I2C and SLIMbus audio interfaces.
On slimbus interface it supports two data lanes; 16 Tx ports
and 8 Rx ports. It has Seven DACs and nine dedicated interpolators,
Seven (six audio ADCs, and one VBAT ADC), Multibutton headset
control (MBHC), Active noise cancellation and Sidetone paths
and processing.
This patchset adds very basic support for playback and capture
via the 9 interpolators and ADC respectively.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove duplicated entry and add missing zero in rate constraints.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCM format type is with __bitwise, so we should use the dedicated
snd_pcm_format_t instead of int.
This fixes the sparse warning like:
sound/soc/codecs/pcm186x.c:268:44: warning: incorrect type in initializer (different base types)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch fixes the issue of the delay volume applied.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull the generic drm_audio_component support, which will be used later
for AMD/ATI and other HD-audio HDMI codec drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a mixer control for the IN3 Boost volume, IN3 is used for the headset
mic on most devices, so this is necessary to control the headset mic
volume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the compressed streams in DSP firmwares are
identified essentially by looking at a fixed location inside
the firmware. This is fragile and also limits things to a
single compressed stream.
Here a new form of firmware parameter is added, the HOST_BUFFER
which identifies a compressed stream from meta-data in the
firmware file. This is more robust and allows for the possiblity
of using multiple streams per core in the future. Currently the
implementation is still limited to a single stream and will
use the first HOST_BUFFER parameter encountered. If there aren't
any HOST_BUFFER parameters it will fall back to the legacy way
of finding the host buffer.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Newer voice control firmwares can capture multiple audio channels.
Allow up to 8 channels for future-proofing.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when creating ALSA control names for the DSP the length of any
prefix applied to the CODEC is not taken into account. Whilst this is
mostly harmless it does result in ALSA doing the truncation of the
control names and printing a warning. It is better to have the driver do
the truncation so it can truncate from the start of parameter name
itself to give a greater chance of the result maintain a unique name.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6396bb2215 ("treewide: kzalloc() -> kcalloc()") was
overlooked when doing some refactoring to the algorithm list
handling, which lead to twice as much buffer being allocated
as required for reading the algorithm list. A kcalloc is no
longer appropriate since the allocation size is now in bytes
not registers, as such change back to kzalloc.
Fixes: 7f7cca08ab ("ASoC: wm_adsp: Simplify handling of alg offset and length")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All controls derived from the loaded firmware should be created prior
to returning from the preloader's put function, such that they are
immediately available to user-space.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for power management of HDAC HDMI codec device for
various scenarios such as S0/S3, probe and playback use case.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_lib_mmap_vmalloc() was supposed to be implemented with
somewhat special for vmalloc handling, but in the end, this turned to
just the default handler, i.e. NULL. As the situation has never
changed over decades, let's rip it off.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is the final step for more generic support of DRM audio
component. The generic audio component code is now moved to its own
file, and the symbols are renamed from snd_hac_i915_* to
snd_hdac_acomp_*, respectively. The generic code is enabled via the
new kconfig, CONFIG_SND_HDA_COMPONENT, while CONFIG_SND_HDA_I915 is
kept as the super-class.
Along with the split, three new callbacks are added to audio_ops:
pin2port is for providing the conversion between the pin number and
the widget id, and master_bind/master_unbin are called at binding /
unbinding the master component, respectively. All these are optional,
but used in i915 implementation and also other later implementations.
A note about the new snd_hdac_acomp_init() function: there is a slight
difference between this and the old snd_hdac_i915_init(). The latter
(still) synchronizes with the master component binding, i.e. it
assures that the relevant DRM component gets bound when it returns, or
gives a negative error. Meanwhile the new function doesn't
synchronize but just leaves as is. It's the responsibility by the
caller's side to synchronize, or the caller may accept the
asynchronous binding on the fly.
v1->v2: Fix missing NULL check in master_bind/unbind
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HD-audio i915 binding code contains a single pointer, hdac_acomp,
for allowing the access to audio component from the master bind/unbind
callbacks. This was needed because the callbacks pass only the device
pointer and we can't guarantee the object type assigned to the drvdata
(which is free for each controller driver implementation).
And this implementation will be a problem if we support multiple
components for different DRM drivers, not only i915.
As a solution, allocate the audio component object via devres and
associate it with the given device, so that the component callbacks
can refer to it via devres_find().
The removal of the object is still done half-manually via
devres_destroy() to make the code consistent (although it may work
without the explicit call).
Also, the snd_hda_i915_register_notifier() had the reference to
hdac_acomp as well. In this patch, the corresponding code is removed
by passing hdac_bus object to the function, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For allowing other drivers to use the DRM audio component, rename the
i915_audio_component_* with drm_audio_component_*, and split the
generic part into drm_audio_component.h. The i915 specific stuff
remains in struct i915_audio_component, which contains
drm_audio_component as the base.
The license of drm_audio_component.h is kept to MIT as same as the the
original i915_component.h.
This is a preliminary change for further development, and no
functional changes by this patch itself, merely code-split and
renames.
v1->v2: Use SPDX for drm_audio_component.h, fix remaining i915
argument in drm_audio_component.h
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 943fa02282 ("ASoC: hdmi-codec: Use different name for playback
streams") broke hdmi-codec's routing between it's output "TX" widget
and the S/PDIF or I2S streams by renaming the streams.
Whether an error occurs or not is dependent on whether there is another
widget called "Playback" registered by some other component - if there
is, that widget will be (incorrectly) bound to the HDMI codec's "TX"
output widget. If we end up connecting "TX" incorrectly, it can result
in components not being started, causing no audio output.
Since the I2S and S/PDIF streams now have different names, we can't
use a static route at component level to describe the relationship, so
arrange to dynamically create the route when the DAI driver is probed.
Fixes: 943fa02282 ("ASoC: hdmi-codec: Use different name for playback streams")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable button press detection for headsets by using the ovcd IRQ to get
notified of button presses.
This is modelled after (almost exactly copied from) the button press code
for the rt5640 which has identical ovcd hardware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the machine driver to disable jack-detect over a suspend/resume by
calling snd_soc_component_set_jack(NULL).
Note this renames rt5651_set_jack, where all the jack-enable work was done
to rt5651_enable_jack_detect. This function can now no longer fail as it
does not request the IRQ anymore. It can still be passed an invalid jack
source, but that should never happen, so this is now logged and treated as
no jack source.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On removal we must free the IRQ *before* cancelling the jack-detect work,
so that the jack-detect work cannot be rescheduled by the IRQ.
Before this commit we were cancelling the jack-detect work from the
driver remove callback, while relying on devm to free the IRQ, which
happens after the remove callback.
This is the wrong order. This commit uses a devm-action to register
a devm callback which cancels the work, before requesting the IRQ
(devm tears things down in reverse order). This also allows us to
remove the now empty remove driver callback.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The playback DAI is connected to the DSP and the DSP might be sourcing
signals from the playback stream. Add a DAPM route between the two to make
sure that the playback DAI is powered up, when the DSP is active.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suffix ULL to constant 256 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
256 * fs * 2 * mclk_src_scaling[i].param
Addresses-Coverity-ID: 1432039 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suffix ULL to constant 256 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
256 * fs * 2 * mclk_src_scaling[i].param
Addresses-Coverity-ID: 1339616 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the es7154 which is basically an es7134 with an
embedded power amplifier and lower maximum sample rate
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop AVDD in favor of PVDD to match the names used in the datasheet
and only claim PVDD on the es7154. The es7134 and es7144 don't have
a separate supply for the digital I/O.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the everest es7241 which is a simple 2 channels
analog to digital converter.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are currently using power saving mode for button detection.
However, it will impact the headset recording performance.
This patch will switch button detection to normal mode in capture
and switch to power saving mode in the end of capture.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the VDD and AVDD power supplies to the DAPM graph as some board may
need to enable a regulator to turn them on.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For each supported sample rate, the es7134 can work with several
mclk / sample rate ratio. Check if ratio we get is actually OK.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
64Khz is actually not supported by the es7134 according to the datasheet
Fixes: 9000b59d7a ("ASoC: es7134: add es7134 DAC driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes the hdac_ext_driver structure. The legacy and
enhanced HDaudio capabilities can be handled in a backward-compatible
way without separate definitions.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes the hdac_ext_bus structure. The legacy and
enhanced HDaudio capabilities can be handled in a backward-compatible
way without separate definitions.
Follow-up patches in this series handle the driver definition.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes the hdac_ext_device structure. The legacy and
enhanced HDaudio capabilities can be handled in a backward-compatible
way without separate definitions.
Follow-up patches in this series handle the bus and driver definitions.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add simple-audio-amplifier to the list of available compatible
Suggested-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dio2125 is simple enough that we can make it a generic component.
Just rename and sed the dio2125 amplifier driver to simple_amplifier.
Suggested-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In its current shape, the driver just ignores errors returned by
regulator_get() at component_probe(). This doesn't hurt on Amstrad
Delta board as long as it registers the codec device at late_initcall,
when the regulator which depends on basic-mmio-gpio device (probed as
late as at dev_initcall) is already available. Otherwise the driver
may end up trying to control a codec which is not powered up.
Remove that dependency on initialization order by handling the error.
If the regulator is not yet available and -ENODEV is returned, convert
it to -EPROBE_DEFER to get another chance.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using devm_snd_soc_register_component() and drop all of the code
related to .remove hook.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using devm_snd_soc_register_component() and drop all of the code
related to .remove hook.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code is not setting the compressed IRQ as a wake
source. Normally this doesn't cause any issues as the CODEC
IRQ is set as a wake source by the jack detection code and the
CODEC only produces a single IRQ line. However if the system
is not using jack detection the compressed audio IRQ should
still function as a wake source, as such directly set the
compressed audio IRQ as a wake source.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code that reads the algorithm list from the DSP is
somewhat unclear, it converts directly from bytes to registers using
a hard coded divide by 2. Most offsets are usually handled in DSP
words within the driver and there is a function specifically for
converting from words to register addresses. So update the handling
to use these. This also removes the assumption that the registers
are 16-bit word addressed, which will no longer be true on some of
our newer parts.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Work is guaranteed to be initialized on exit. Drop the unnecessary
if statement and always call flush_work.
This fixes a warning seen with clang:
sound/soc/codecs/pcm1789.c:265:13: warning: address of 'priv->work' will
always evaluate to 'true' [-Wpointer-bool-conversion]
if (&priv->work)
~~ ~~~~~~^~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add headphone auto switching controls
Signed-off-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These aren't needed and some userspace apps don't work consistently with
them.
Remove Playback/Capture from control names
Signed-off-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The structure soc_codec_dev_ak4458 is local to the source and do not
need to be in global scope and can be const, make it static const.
Cleans up sparse warnings:
warning: symbol 'soc_codec_dev_ak4458' was not declared. Should it
be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The structure ak5558_pm and soc_codec_dev_ak5558 are local to the
source and do not need to be in global scope, so make them static.
Also make soc_codec_dev_ak5558 static.
Cleans up sparse warnings:
warning: symbol 'ak5558_pm' was not declared. Should it be static?
warning: symbol 'soc_codec_dev_ak5558' was not declared. Should it be
static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc 4.1.2:
sound/soc/codecs/rt1305.c: In function ‘rt1305_calibrate’:
sound/soc/codecs/rt1305.c:1069: warning: integer constant is too large for ‘long’ type
sound/soc/codecs/rt1305.c:1086: warning: integer constant is too large for ‘long’ type
Add the missing "ULL" suffixes to fix this.
Fixes: 29bc643ddd ("ASoC: rt1305: Add RT1305/RT1306 amplifier driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a very big update, mainly due to a huge set of new drivers some
of which are individually very large. We also have a lot of fixes for
the topology stuff, several of the users have stepped up and fixed some
the serious issues there, and continued progress on the transition away
from CODEC specific drivers to generic component drivers.
- Many fixes for the topology code, including fixes for the half done
v4 ABI compatibility from Guenter Roeck and other ABI fixes from
Kirill Marinushkin.
- Lots of cleanup for Intel platforms based on Realtek CODECs from Hans
de Goode.
- More followups on removing legacy CODEC things and transitioning to
components from Morimoto-san.
- Conversion of OMAP DMA to the new, more standard SDMA-PCM driver.
- A series of fixes and updates to the rather elderly Cirrus Logic SoC
drivers from Alexander Sverdlin.
- Qualcomm DSP support from Srinivas Kandagatla.
- New drivers for Analog SSM2305, Atmel I2S controllers, Mediatek
MT6351, MT6797 and MT7622, Qualcomm DSPs, Realtek RT1305, RT1306 and
RT5668 and TI TSCS454
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlsWonITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0KBaB/sHLhq0NwDC+9sHEtFJLB2BvinShIm4
aPk54T930r/aHZ3aht+qWWU9DTBA5VcaLXVxGJ6J2KrZ8QGOiUAt9QG6kiOb/ltE
8ORJfsYsRpFSBMPqae/92uxV4WDYLpC1G/ty+VLY8Balp24nDvbrV6oo+xhNTDWW
wwWVPQkLSDF29EgZJc5zX/PxrjuPSkawRe28P0GI/exXkaP7i8HNmgEl1nlOEgzs
PiZW7YzsA/6VjSUtYMKWDlXmhkDpb/A/7bGa7JzQZEtN5zM8512gyQ12Hhkrrqn4
0MvcUUPCw+tBj0A/sdpsPSf476eQ0SUbU85JF2r8sVNpeChb6Su9Q7WI
=OuIx
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.18
This is a very big update, mainly due to a huge set of new drivers some
of which are individually very large. We also have a lot of fixes for
the topology stuff, several of the users have stepped up and fixed some
the serious issues there, and continued progress on the transition away
from CODEC specific drivers to generic component drivers.
- Many fixes for the topology code, including fixes for the half done
v4 ABI compatibility from Guenter Roeck and other ABI fixes from
Kirill Marinushkin.
- Lots of cleanup for Intel platforms based on Realtek CODECs from Hans
de Goode.
- More followups on removing legacy CODEC things and transitioning to
components from Morimoto-san.
- Conversion of OMAP DMA to the new, more standard SDMA-PCM driver.
- A series of fixes and updates to the rather elderly Cirrus Logic SoC
drivers from Alexander Sverdlin.
- Qualcomm DSP support from Srinivas Kandagatla.
- New drivers for Analog SSM2305, Atmel I2S controllers, Mediatek
MT6351, MT6797 and MT7622, Qualcomm DSPs, Realtek RT1305, RT1306 and
RT5668 and TI TSCS454
Currently there is no support for Tempo Semiconductor's TSCS454 CODEC.
Add support for it.
Signed-off-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
match_string() returns the index of an array for a matching string,
which can be used instead of open coded variant.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
match_string() returns the index of an array for a matching string,
which can be used instead of open coded variant.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_GPIOLIB is disabled, this codec fails to build
because gpio/consumer.h is not included implicitly.
sound/soc/codecs/pcm1789.c: In function 'pcm1789_common_init':
sound/soc/codecs/pcm1789.c:247:19: error: implicit declaration of function 'devm_gpiod_get_optional'; did you mean 'devm_gpio_request_one'? [-Werror=implicit-function-declaration]
pcm1789->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
^~~~~~~~~~~~~~~~~~~~~~~
Fixes: 4ae340d1be ("ASoC: codecs: Add support for PCM1789")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the S_<FOO> symbolic permissions to their octal equivalents as
using octal and not symbolic permissions is preferred by many as more
readable.
see: https://lkml.org/lkml/2016/8/2/1945
Done with automated conversion via:
$ ./scripts/checkpatch.pl -f --types=SYMBOLIC_PERMS --fix-inplace <files...>
Miscellanea:
o Wrapped one multi-line call to a single line
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
FOr platforms that use the simple-card driver, the codec cannot be selected
through 'select' magic in Kconfig. So turn this into a real config option.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is needed when the codec is instanciated from from a device tree.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
HID is assumed to be made of TI PCI ID (0x104C) + part number, so all
four 104C5121, 104C5122, 104C5141 104C5142 are valid.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no platform code that uses i2c module table.
Remove it altogether and adjust ->probe() to be ->probe_new().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make C-header and SPDX-License-Identifier header uniform.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistakes in SND_SOC_BYTES literal strings
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in SOC_ENUM literal string
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set PR-38 register to 0x1fe1 will make PLL function more stable.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ssm2305 is a simple Class-D audio amplifier. A application can
turn on/off the device by a gpio. It's also possible to hardwire the
shutdown pin.
Tested on a i.MX6 based custom board.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 9958e8afbcad ("ASoC: rt5663: Use the set_jack() instead of the export function")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch replaces the export function with the new API set_jack().
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo Ideapad Mixx 320 has a digital mic connected to DMIC2
add a DMI based quirk pointing to the intel_braswell_platform_data
for devices with a mic on DMIC2.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo Ideapad Mixx 310 has a differential internal analog mic,
add platform-data for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable button press detection for headsets by using the ovcd IRQ to get
notified of button presses.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add jack-detect support, loosely based on earlier work on this by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Francisco mendez <francisco.mendez@intel.com>
Note getting the OVCD to work reliable was sort of finicky, so there are
quite a few comments on this to hopefully avoid people breaking it in the
future.
This (and the follow-up button press support) has been tested on the
following devices:
Acer Iconia Tab 8 W1-810
Asus T100CHI
Asus T100TA
Asus T200TA
Axxo WT1011
Chuwi Vi8
Dell Venue 8 Pro 5830
HP Pavilion X2 10-n000nd
HP Stream 7
I.T. Works TW891
Lamina I8270
MSI S100
Peaq C1010
Pipo W4
PoV MobiiTAB-P800W (v2.0)
Toshiba Click Mini L9W-B
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196377
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow specifying dmic data pins through device-properties / dt. This will
allow us to stop exporting rt5640_dmic_enable() once all callers of it have
been converted to setting device-properties for this instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms the platform code may need to add device-properties,
rather then relying only on properties set by the firmware.
This commit moves the parsing of the device-properties from the i2c-driver
probe() function, which may be called at any time, to the component-driver
probe() function, which gets called after the platform code calls
snd_soc_register_card().
This allows the platform code to attach extra device-properties before
the device-properties are parsed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no in tree users of platform-data for the rt5640 codec driver,
so lets remove support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
is_sys_clk_from_pll() is used as a snd_soc_dapm_route.connected callback,
checking RT5640_GBL_CLK to determine if the sys-clk is PLL1 and thus the
PWR_PLL bit in reg PWR_ANLG2 must be set.
RT5640_GBL_CLK is changed by rt5640_set_dai_sysclk(), which gets called by
the pre_pmu / post_pmd functions of the "Platform Clock" dapm-supply.
This creates an ordering issue, during a dapm transition first all
connected() callbacks are called to build a list of supplies to enable
and then the complete list is walked to enable the supplies. Since the
connected() check happens before enabling any supplies,
is_sys_clk_from_pll() ends up deciding if the PWR_PLL bit should be set
based on the state the "Platform Clock" supply had *before* the transition.
This sometimes results in PWR_PLL being off, even though *after* the
transition PLL1 is configured as sys-clk.
This commit removes is_sys_clk_from_pll() instead simply setting / clearing
PWR_PLL in rt5640_set_dai_sysclk() based on the selected sys-clk, which
fixes this and as a bonus results in a nice cleanup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_warn messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function dev_get_regmap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the use_single_rw flag to regmap config since the
device does not support bulk transactions over i2c.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The TAS6424 incorporates both DC-load and AC-load diagnostics which are
used to determine the status of the load. The DC diagnostics runs when any
channel is directed to leave the Hi-Z state and enter the MUTE or PLAY
state.
The DC diagnostics are turned on by default but, if a fast startup without
diagnostics is required, the diagnostics can be disabled using a dedicated
ALSA control.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Organize the paths of the mixer, "Input Boost Stage", including
the routes of the mixer. The control is not used correctly before.
Besides, the driver changes the name of the mixer controls.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mute can be connected to GPIO. In that case we have to drive it to the
correct value
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The standby pin can be connected to a GPIO. In that case we have to drive
it to the correct values for the TAS6424 to operate properly.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the MediaTek MT6351 codec driver.
MT6351 communicate with SoC through MediaTek PMIC wrapper.
MT6351 use MediaTek proprietary audio interface.
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the correct functions to allow a name prefix assigned through
codec_conf to be taken into consideration whilst enabling and disabling
the preloader widget.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently logical and is being used instead of bitwise and. Fix this.
Detected by CoverityScan, CID#1468008 ("Logical vs bitwise operator")
Fixes: d59fb28562 ("ASoC: rt5668: add rt5668B codec driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As snd_soc_jack_report() can sleep, move handling of mbhc events to a
thread context rather than in interrupt context.
Fixes: de66b34550 ('ASoC: codecs: msm8916-wcd-analog: add MBHC support')
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SAR ADC of key press detection varies depending on headset.
We can't make a set of common threshold values for every case.
Therefore, the driver provides configuration for user and
they can set up values by UCM configuration.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/rt1305.c:1174:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: 29bc643ddd ("ASoC: rt1305: Add RT1305/RT1306 amplifier driver")
CC: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch added <linux/acpi.h> header
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial amplifier driver for rt1305/rt1306.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds the missing register in the readable table.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reloading fw causes an audiable popping sound, we can avoid this
by not reloading if the samplerate is the same as before.
Signed-off-by: Danny Smith <dannys@axis.com>
Signed-off-by: Robert Rosengren <robert.rosengren@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Long lines and bad alignment disturbs the reading pleasure.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Long lines and bad alignment disturbs the reading pleasure.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TSCS42xx relies on set_sysclk to get a unique clock id and rate,
which prevents it from being used with the simple-card.
Remove set_sysclk callback
Add CCF support to get clock id and rate
Add clocks and clock-names to device tree binding
Signed-off-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove blrcm from private data
Remove dev from private data
Signed-off-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shorten lines greater than 80 chars
Add const to struct snd_soc_component_driver
Signed-off-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP_RUN needs to be disabled during firmware write otherwise
we can end up with undefined behavior if writing to a dsp which
is already running firmware.
Signed-off-by: Danny Smith <dannys@axis.com>
Signed-off-by: Robert Rosengren <robert.rosengren@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Structure i2c_driver does not need to set the owner field, as this will
be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
User reports an issue in Ubuntu about the device switch upon playback.
We find the FLL will disalbe when switching headphone to speaker.
The pulseaudio will stop the headphone and close its power. Then,
it just opens the speaker and turn on its power. Therefore,
the supply of system clock does the OFF event and disables FLL.
But the FLL doesn't enable again when the speaker powers on.
The patch adds the recovery of system clock to enable FLL again
for this case. And it covers the case that system clock from MCLK.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need 2 .remove callback
Fixes: 7480389fb0 ("ASoC: twl6040: replace codec to component")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"HV" and "VREF" will be powered up when jack type detection process is
started and will be powered off when jack type detection process is finished.
It will generate an unexpected interrupt signal when they are powered
up during the capture process. Codec driver will do the jack type detection
process and we can't capture properly before the jack detection process is
finished. This patch will not power off the "HV" and "VREF" widgets if
headset is detected and it will solve the unexpected interrupt issue. As a
result, it will also solve the silence data captured at the beginning in
headset mic recording issue.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"HV" and "VREF" will be powered up when jack type detection process is
started and will be powered off when jack type detection process is finished.
It will generate an unexpected interrupt signal when they are powered
up during the capture process. Codec driver will do the jack type detection
process and we can't capture properly before the jack detection process is
finished. This patch will not power off the "HV" and "VREF" widgets if
headset is detected and it will solve the unexpected interrupt issue. As a
result, it will also solve the silence data captured at the beginning in
headset mic recording issue.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSM2602 driver is broken on recent kernels (at least
since 4.9). User space applications such as amixer or
alsamixer get EIO when attempting to access codec
controls via the relevant IOCTLs.
Root cause of these failures is the regcache_hw_init
function in drivers/base/regmap/regcache.c, which
prevents regmap cache initalization from the
reg_defaults_raw element of the regmap_config structure
when registers are write only. It also disables the
regmap cache entirely when all registers are write only
or volatile as is the case for the SSM2602 driver.
Using the reg_defaults element of the regmap_config
structure rather than the reg_defaults_raw element to
initalize the regmap cache avoids the logic in the
regcache_hw_init function entirely. It also makes this
driver consistent with other ASoC codec drivers, as
this driver was the ONLY codec driver that used the
reg_defaults_raw element to initalize the cache.
Tested on Digilent Zybo Z7 development board which has
a SSM2603 codec chip connected to a Xilinx Zynq SoC.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add Texas Instruments's PCM1789 DAC support.
It is a simple DAC and does not have many registers.
One particularity about this DAC is that the clocks must be
always enabled. Also, an entire software reset is necessary
while starting to play a sound otherwise, the clocks are not
synchronized (so the DAC is not able to send data).
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the remove callback is removed, the snd_soc_unregister_component()
is missing when remove device. Using devm_snd_soc_register_component()
instead of snd_soc_register_component().
Fixes: d06f33aed8 ("ASoC: da7210: replace codec to component")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the remove callback is removed, the snd_soc_unregister_component()
is missing when remove device. Using devm_snd_soc_register_component()
instead of snd_soc_register_component().
Fixes: 10dc44c646 ("ASoC: wm8400: replace codec to component")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
structure da7219_dai_clks_ops is local to the source and does not need
to be in global scope, so make it static.
Cleans up sparse warning:
sound/soc/codecs/da7219.c:1777:22: warning: symbol 'da7219_dai_clks_ops'
was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: ASoC: da7219: Add common clock usage for providing DAI clks
clkdev_drop usage in the codec remove function should be dependent
on if CONFIG_COMMON_CLK is defined for the platform, otherwise it
can cause build failures for platforms that do not support this.
The clkdev_* functions are still defined for those platforms, in
headers and source but the functions are not linked in.
This patch resolves this issue, so clkdev_drop is only used if
CONFIG_COMMON_CLK is defined.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the definitions of constants used in the dt-bindings from
include/sound/rt5651.h to include/dt-bindings/sound/rt5651.h.
As dt-bindings headers may also be parsed by the dt-compiler, they cannot
use enums, only defines, so this commit also changes the code declaring
the constants to use defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to have the write callback to use the code.
Fixes: 7480389fb0 ("ASoC: twl6040: replace codec to component")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control bits of ADC 1 and 2 clock are different. We have to
separate it.
Signed-off-by: Zhong An <zhongan@pinecone.net>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control register for ADC L2 and R2 is RT5659_PWR_DIG_1
not RT5659_PWR_DIG_2.
Signed-off-by: Zhong An <zhongan@pinecone.net>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5659_PWR_ADC_L2_BIT should be 2.
Signed-off-by: Zhong An <zhongan@pinecone.net>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a need to use DA7219 as DAI clock master for other codecs
within a system, which means that the DAI clocks are required to
remain, regardless of whether the codec is actually running
playback/capture. To be able to expose control of the DAI clocking
the common clock framework has been employed.
The current implementation adds a simple clock gate for enabling
and disabling the DAI clocks, with no rate control supported
(this is still handled through standard hw_params() functions as
before). If DT is enabled then the clock is added to the OF
providers list, otherwise a clkdev lookup is used.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We get the insertion event before the jack is fully inserted at which point
the second ring on a TRRS connector may short the 2nd ring and sleeve
contacts. Testing has shown that this short-circuit may happen as late
as 500ms after the insertion event, but it never lasts longer then 300ms.
This commit changes the detection algorithm to require 5 identical OVCD
values in a row at 100 ms intervals to fix the jack-type sometimes getting
mis-detected.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add rt5651_jack_inserted() helper to get the jack-detect switch status,
This is a preparation patch for rewriting the jack type-detection to
make it more reliable.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using RCCLK instead of MCLK / PLL1 the OVCD status often gets stuck
at its last value, which breaks jack-type detection.
This commit fixes this by force-enabling the platform clock when doing
jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the mic-gnd contacts are short-circuited by a headphones plug, the
hardware periodically retries if it can apply the bias-current leading to
the OVCD status flip-flopping 1-0-1 with it being 0 about 10% of the time.
This commit enables the sticky bit for the OVCD status to deal with this.
This commit also introduces 2 helper functions to deal with the OVCD
status bit, this may seem a bit overkill now, but these will also be
used in future patches.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect if
an inserted jack is a headset or headphones (mic shorted to ground).
The threshold for at which current the OVCD triggers on the rt5651 is not
only controlled by setting the absolute current limit, but also by setting
a scale factor which applies to the limit. Testing has shown that we need
to set both (depending on the board).
This commit adds support for the sofar unused OVCD scale-factor register
and adds support for specifying non-default values for it through the
"realtek,over-current-scale-factor" device-property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect
if an inserted jack is a headset or headphones (mic shorted to ground).
Some boards may need different values for the OVCD current threshold
because of a resistor on the board in serial with or parallel to the
jack mic contact.
This commit adds support for configuring the OCVD current threshold
through the "realtek,over-current-threshold-microamp" device-property.
Note this commit changes the default value from 600uA to 2000uA,
because testing has shown 600uA to be a poor default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Configure the jack-detect source through a device-property which can be
set by code outside of the codec driver. Rather then putting platform
specific DMI quirks inside the generic codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The idea behind exporting rt5651_apply_properties(), was for it to be used
on platforms where the platform code may need to add device-properties,
rather then relying only on properties set by the firmware. The platform
code could then call rt5651_apply_properties() after adding properties to
make sure that the codec driver was aware of the new properties.
But this is not necessary, as long as we do all property parsing from
the codec component-driver's probe function (or later) then the machine
driver can attach properties before calling snd_soc_register_card and
calling rt5651_apply_properties() for ordering reasons is not necessary.
This commit makes rt5651_apply_properties() private and adds 2 comments
documenting that all property parsing must be done from the codec
component-driver's probe function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver probe function has no use and can be deleted.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc-4.1.2, if CONFIG_SND_SOC_RT5514_SPI is not set:
sound/soc/codecs/rt5514.c: In function ‘rt5514_dsp_voice_wake_up_put’:
sound/soc/codecs/rt5514.c:363: warning: ‘buf[0]’ is used uninitialized in this function
sound/soc/codecs/rt5514.c:363: warning: ‘buf[1]’ is used uninitialized in this function
sound/soc/codecs/rt5514.c:363: warning: ‘buf[2]’ is used uninitialized in this function
sound/soc/codecs/rt5514.c:363: warning: ‘buf[3]’ is used uninitialized in this function
Fix this by initializing the buffer with zeroes, to avoid random bits
being written to the calibration register later.
Fixes: fc9cab0583 ("ASoC: rt5514: The DSP clock can be calibrated by the other clock source")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5514_dsp_voice_wake_up_put() passes "(u8 *)&buf" to
rt5514_spi_burst_read(), where the cast is needed to silence a compiler
warning:
sound/soc/codecs/rt5514.c: In function ‘rt5514_dsp_voice_wake_up_put’:
sound/soc/codecs/rt5514.c:357: warning: passing argument 2 of ‘rt5514_spi_burst_read’ from incompatible pointer type
However, as the variable is declared as an array ("u8 buf[8]"), the
function should just pass "buf" instead.
Fixes: fc9cab0583 ("ASoC: rt5514: The DSP clock can be calibrated by the other clock source")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVCD is not only useful for jack-type detection, but is also useful
to protect against over-current faults in general, so always keep
OVCD enabled, instead of only enabling it for jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only configure OVCD once at set_jack time, rather then configuring
it on every jack-insertion event and switch to using bit field defines
instead of hardcoding a magic value.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To determine if a plugged in jack is a headset (speakers + mic) or
headphones (mic contact shorted to ground) we use the micbias1 OVer Current
Detect (OVCD) functionality.
For this to work we need to have a micbias current to actually cause an
overcurrent condition when headphones are plugged in, so jack-type
detection requires both the LDO and micbias1 supplies to be on.
Before this commit there were 2 issues with the handling of this:
1) The LDO supply was force-enabled twice and never disabled again even
though it only needs to be forced on when doing jack-type detection
2) micbias1 was not force-enabled, and thus may be off when doing jack-type
detection
This commit fixes both by force-enabling the LDO and micbias1 supplies
before checking for an overcurrent condition and disabling them afterwards.
Note that both supplies will still get turned on normally (and OVCD will
protect against overcurrent) when the micbias1 is enabled normally because
the user has activated a sound stream recording from the mic.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the "JD power" dapm supply which gets force-enabled once when
using jack-detect and never gets disabled again.
Since the PWR_JD_M bit simply needs to be always on when using jack-detect
there is no need to have it tracked by dapm, instead we can simply set it
to 1 once when initializing the jack-detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that rt5651_set_bias_level(BIAS_OFF) no longer modifies the LDO
voltage selection bits, there is no need to set them each time we move
to standby. Instead configure them once at component-probe() time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the setup of the PWR_ANLG1 reg which was done directly before
calling snd_soc_component_force_bias_level(SND_SOC_BIAS_OFF), as the
latter will override any settings done to PWR_ANLG1 immediately anyways.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, including the jack-detect and PLL power bits. When jack-detection
support was introduced a special case for jack-detect was added which
hard-codes a register value to keep both on.
This commit removes the jack-detect special case, instead simply leaving
these bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PWR_ANLG1 reg not only contains various power on/off bits, it also
contains 2 bits which select if the LDO generates 1.0, 1.1 or 1.2V. Note
there is a separate on/off bit for the LDO.
rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, when jack-detection support was introduced a special case for
jack-detect was added which hard-codes a register value to keep the LDO
voltage at 1.2 volt.
This commit removes the jack-detect special case, instead simply always
leaving the LDO voltage control bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5651_set_bias_level() function was turning everything off at
SND_SOC_BIAS_STANDBY, rather then at SND_SOC_BIAS_OFF, requiring the bias-
level to be raised to SND_SOC_BIAS_PREPARE before turning anything on.
This is not how the bias-levels are supposed to work, this commit fixes
this by turning everything off at the SND_SOC_BIAS_OFF level and enabling
the pwr-bits needed for minimum functionality at SND_SOC_BIAS_STANDBY.
This fixes the minimum set of pwr-bits not getting enabled when
force-enabling some dapm-supplies (e.g. for jack type detection),
which raises the bias-level to standby.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
is_sys_clk_from_pll() is used as a snd_soc_dapm_route.connected callback,
checking RT5651_GBL_CLK to determine if the sys-clk is PLL1 and thus the
PWR_PLL bit in reg PWR_ANLG2 must be set.
RT5651_GBL_CLK is changed by rt5651_set_dai_sysclk(), which gets called by
the pre_pmu / post_pmd functions of the "Platform Clock" dapm-supply.
This creates an ordering issue, during a dapm transition first all
connected() callbacks are called to build a list of supplies to enable
and then the complete list is walked to enable the supplies. Since the
connected() check happens before enabling any supplies,
is_sys_clk_from_pll() ends up deciding if the PWR_PLL bit should be set
based on the state the "Platform Clock" supply had *before* the transition.
This sometimes results in PWR_PLL being off, even though *after* the
transition PLL1 is configured as sys-clk.
This commit removes is_sys_clk_from_pll() instead simply setting / clearing
PWR_PLL in rt5651_set_dai_sysclk() based on the selected sys-clk, which
fixes this and as a bonus results in a nice cleanup.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codes is stereo only with playback and capture streams bind
to the same rate.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tell user what are clock rate limits and reindent log messages.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the applying of the differential input and dmic properties to a new
rt5651_apply_properties() helper function. This new function can be called
by platform code which attaches properties after probe() has run to apply
these new properties.
Note this also moves the time when we apply these properties for DT
platforms from i2c-probe to snd-component-probe time, this should not
result in any functional difference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the standard component set_jack callback instead of defining a codec
private API for this.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move 2 functions higher up in rt5651.c, this is a preparation patch
to avoid needing forward declarations when moving over from a codec
private function to the standard snd_soc_component_set_jack().
This commit purely moves these 2 functions up, not a single line is
changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all jack-detect initialization to rt5651_set_jack_detect. The main
reason to do this is so that platform code can setup jack-detect properties
after the device has been probed, which unfortunately is necessary on some
platforms.
This has 2 additional advantages:
1) Grouping all jack-detect init together makes it easier to follow what
is happening and results in a small reduction in the number of loc.
2) Before we would register the irq handler before rt5651->hp_jack was
assigned, leading to a potential NULL deref if the jack_detect work runs
before the machine driver has called set_jack.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no in tree users of platform-data for the rt5651 codec driver,
so lets remove support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Normal 512-byte get/set of a TLV isn't supported but we were
registering the normal get/set anyway and relying on omitting
the SNDRV_CTL_ELEM_ACCESS_[READ|WRITE] flags to prevent them
being called.
Trouble is if this gets broken in the core ALSA code - as it has
been since at least 4.14 - the standard get/set can be called
unexpectedly and corrupt memory.
There's no point providing functions that won't be called and
it's a trivial change. The benefit is that if the ALSA core gets
broken again we get a big fat immediate NULL dereference instead
of a memory corruption timebomb.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Motorola CPCAP is a PMIC with audio functionality, that can be
found on Motorola Droid 4 and probably a few other phones from
Motorola's Droid series.
The driver has been written from scratch using Motorola's Android
driver, register dumps from running Android and datasheet for NXP
MC13783UG (which is similar to Motorola CPCAP, but not the same).
The chip provides two audio interfaces, that can be muxed to two
different audio codecs. One provides support for stereo output
(named StDAC or HiFi), while the other only provides mono output
(named Voice). Only the Voice codec provides a Capture interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support of the ROHM BD28623MUV
Class D speaker amplifier for Flat-panel TVs.
This IC delivers an output power of 20W + 20W.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clear the buffer data structure on each trigger start such that the
buffer is in a sensible state even if the DSP itself didn't restart.
This is necessary to support voice control streams which can trigger
multiple times without reloading the firmware.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Repair any formatting/style issues that can be fixed without major
code refactoring.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use // for .c and /* for .h files according to:
Documentation/process/license-rules.rst file.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hcp->chmap_info must not be freed up in the hdmi_codec_remove()
function as it leads to kernel crash due ALSA core's
pcm_chmap_ctl_private_free() is trying to free it up again when the card
destroyed via snd_card_free.
Since the driver was converted to devm_snd_soc_register_component() the
whole platform_device.remove can be removed.
Commit cd6111b262 ("ASoC: hdmi-codec: add channel mapping control")
should not have added the kfree(hcp->chmap_info); to the hdmi_codec_remove
function.
[Separate verison of the fix for -next -- broonie]
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hcp->chmap_info must not be freed up in the hdmi_codec_remove()
function as it leads to kernel crash due ALSA core's
pcm_chmap_ctl_private_free() is trying to free it up again when the card
destroyed via snd_card_free.
Commit cd6111b262 ("ASoC: hdmi-codec: add channel mapping control")
should not have added the kfree(hcp->chmap_info); to the hdmi_codec_remove
function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max9759 is a gpio controlled amplifier.
Tested on a Variscite Dart MX6 SoM based custom board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify SPDX comment style to match the rules. Since the original
code had a GPL-2.0 license and SPDX is compatible with GPL-2.0+,
we also modified the MODULE_LICENSE.
Signed-off-by: Cosmin-Gabriel Samoila <cosmin.samoila@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding ACPI entry id for probing the driver.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some systems a delay is needed after switching on the clocks, to allow
the output to stabilize and avoid a popping noise at the beginning of
the recording. Add the optional device tree property 'wakeup-delay-ms'
and apply the specified delay after enabling the mic. A blocking delay
can't be applied in dmic_daiops_trigger() since the function is called
in atomic context. Instead use a DAPM event handler to set the enable
GPIO and apply the delay in the handler.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALC5651 does not like multi-write accesses, avoid them. This fixes:
rt5651 i2c-10EC5651:00: Unable to sync registers 0x27-0x28. -121
Errors on resume (and all registers after the registers in the error not
being synced).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Enable 5-band graphic equalizer which allows manipulation of
gain in range -11.75dB to 12dB for 5 specific sound bands:
115Hz, 330Hz, 990Hz, 3000Hz, 9900Hz.
Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mux for choosing DAC source: ADC, I2S or DAP. DAP - digital
audio processing block. Moreover create choosing mux for DAP main
source (ADC or I2S) and DAP mixer source (ADC or I2S). Mixer block
allows summing DAP main and mixer sources togheter with defined
volumes.
Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With P0 R29, Bit2 set the I2S clocks will be running when the DAC/ADC is
powered down, but still the codec need to be powered up by needing at least
one complete DAPM path for the stream.
If the AIF is not needed (analog loopback for example) the I2S clocks will
not run as they are not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Suggested-by: Stefan Müller-Klieser <s.mueller-klieser@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio interface is not really the DAC input. Use more generic name for
it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
base and sysclk_reg should be unsigned int, as that is what
regmap takes as a register address.
sysclk_mask is used to mask unsigned register values so
should be unsigned.
sysclk_shift is a shift value so is not allowed to be negative.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 8419caa727 ("ASoC: sgtl5000: Do not disable regulators in
SND_SOC_BIAS_OFF") causes the sgtl5000 to fail after a suspend/resume
sequence:
Playing WAVE '/media/a2002011001-e02.wav' : Signed 16 bit Little
Endian, Rate 44100 Hz, Stereo
aplay: pcm_write:2051: write error: Input/output error
The problem is caused by the fact that the aforementioned commit
dropped the cache handling, so re-introduce the register map
resync to fix the problem.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Fixes: 08660086ef ("ASoC: ak4458: Add support for AK4458 DAC driver")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AK5558 is a 32-bit, 768 kHZ sampling, differential input ADC
for digital audio systems.
Datasheet is available at:
https://www.akm.com/akm/en/file/datasheet/AK5558VN.pdf
Initial patch includes support for normal and TDM modes.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Junichi Wakasugi <wakasugi.jb@om.asahi-kasei.co.jp>
[initial coding for 3.18 kernel]
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
[cleanups and porting to 4.9 kernel]
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
[tdm support]
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
[pm support, cleanups and porting to latest kernel]
Signed-off-by: Mark Brown <broonie@kernel.org>
The AK4458 is a 32-bit 8ch Premium DAC that corresponds
to a 768kHz PCM input and an 11.2MHz DSD input at maximum.
It supports I2S, DSD and TDM modes with 24 or 32 bit MSB
or 16, 24, 32 LSB formats. Its datasheet is available here:
https://www.akm.com/akm/en/file/datasheet/AK4458VN.pdf
Signed-off-by: Junichi Wakasugi <wakasugi.jb@om.asahi-kasei.co.jp>
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Cosmin-Gabriel Samoila <cosmin.samoila@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the recently introduced commits hadn't been build tested, fix
that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the const array norm_addrs on the stack, instead make it
static. Makes the object code smaller by over 230 bytes. Also re-format
array data as the insertion of the static keywork made the first line
overly long.
Before:
text data bss dec hex filename
53780 34752 256 88788 15ad4 linux/sound/soc/codecs/tscs42xx.o
After:
text data bss dec hex filename
53461 34840 256 88557 159ed linux/sound/soc/codecs/tscs42xx.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In usecases like hot plug-unplug DP panel or modeset during a playback,
sometimes we observe no audio after codec resets. During no audio
condition, we have noticed that the power state of the pin or the
connector is D3. Optimizing the way we set the power mitigates the
issue. With this changes the verb is sent to set the power state and
waits until actual state reaches target state. Thus ensuring power
state is set.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
{ 0 } only clears the first member of the structure.
The first member of the snd_soc_dapm_update struct is a pointer,
and writing 0 to a pointer results in a sparse warning.
Use the empty struct initializer that clears all the struct members
and fixes the sparse warning.
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
{ 0 } only clears the first member of the structure.
The first member of the snd_soc_dapm_update struct is a pointer,
and writing 0 to a pointer results in a sparse warning.
Use the empty struct initializer that clears all the struct members
and fixes the sparse warning.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current implementation mute codec in global way (DAC block).
That means when user routes sound not from I2S but from
AUX source (LINE_IN) it also will be muted by alsa core.
This should not happen.
Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the reset state of the codec we do not have complete playback or capture
routes.
The audio playback/capture will not work due to missing clock signals on
the I2S bus if PLL, MDAC/NDAC/DAC MADC/NADC/ADC is powered down.
To make sure that even if all output/input is disconnected the codec is
generating clocks, we need to have valid DAPM route in every case to power
up the must needed parts of the codec.
I have verified that switching DAC (during playback) or ADC (during
capture) will stop the I2S clocks, so the only solution is to connect the
'Off' routes as well to output/input.
The routes will be only added if the codec is clock master. In case the
role changes runtime, the applied routes are removed.
Tested on am43x-epos-evm with aic3111 codec in master mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
{ 0 } only clears the first member of the structure.
The first member of the snd_soc_dapm_update struct is a pointer,
and writing 0 to a pointer results in the following sparse warning:
sound/soc/codecs/tlv320aic3x.c:175:47: warning: Using plain integer as NULL pointer
Use the empty struct initializer that clears all the struct members
and fixes the sparse warning.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
{ 0 } only clears the first member of the structure.
The first member of the snd_soc_dapm_update struct is a pointer,
and writing 0 to a pointer results in the following sparse warning:
sound/soc/codecs/wm9712.c:229:47: warning: Using plain integer as NULL pointer
Use the empty struct initializer that clears all the struct members
and fixes the sparse warning.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_runtime_ignore_pmdown_time() returns "ignore pmdown time"
decision. Then, it collects each component driver's .use_pmdown_time
settings by using AND operation.
But, ak4613 has no reason to ignore/use pmdown time.
Thus, It should has use_pmdown_time=0, it means it doesn't have
decision right of "ignore pmdown time".
Otherwise, ak4642 paired driver's pmdown_time settings doesn't
have meaning. In other words, "ignore pmdown time" is determined
irrespective of the value of paired driver's settings
(= ignore will be 0 by ak4642).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_runtime_ignore_pmdown_time() returns "ignore pmdown time"
decision. Then, it collects each component driver's .use_pmdown_time
settings by using AND operation.
But, ak4613 has no reason to ignore/use pmdown time.
Thus, It should has use_pmdown_time=0, it means it doesn't have
decision right of "ignore pmdown time".
Otherwise, ak4613 paired driver's pmdown_time settings doesn't
have meaning. In other words, "ignore pmdown time" is determined
irrespective of the value of paired driver's settings
(= ignore will be 0 by ak4613).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 48c3387642 ("ASoC: wm9081: replace codec to component")
replaced codec to component, but it didn't keep WM9081_DAC_DIGITAL_2
value to reg. This patch fixup it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 041e74b714 ("ASoC: rt5659: Add the support of Intel HDA Header")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove rt5668 support from rt5665 codec driver since rt5668 will
not go into mass production.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All sn95031 stuff was removed in commit 987da3fe17 ("ASoC: sn95031: remove this code")
Since SND_SOC_SN95031 was gone, remove makefile about it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
This patch merges wm5102_compr_platform into soc_codec_dev_wm5102
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
This patch merges rt5514_spi_dai_component into rt5514_spi_component
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
This patch merges cs47l24_compr_platform into soc_codec_dev_cs47l24
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we can replace Codec to Component. Let's do it.
Because Intel/Mediatek platforms are using rt5645/rt5677,
we need to update these all related drivers in same time.
Otherwise compile error/warning happen
rt5645:
xxx_codec_xxx() -> xxx_component_xxx()
.idle_bias_off = 1 -> .idle_bias_on = 0
.ignore_pmdown_time = 0 -> .use_pmdown_time = 1
- -> .endianness = 1
- -> .non_legacy_dai_naming = 1
rt5677:
xxx_codec_xxx() -> xxx_component_xxx()
.idle_bias_off = 1 -> .idle_bias_on = 0
.ignore_pmdown_time = 0 -> .use_pmdown_time = 1
- -> .endianness = 1
- -> .non_legacy_dai_naming = 1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we can replace Codec to Component. Let's do it.
Because there are many drivers which are using adau17x1,
we need to update these all related drivers in same time.
Otherwise compile error/warning happen
adau1761:
xxx_codec_xxx() -> xxx_component_xxx()
.idle_bias_off = 0 -> .idle_bias_on = 1
.ignore_pmdown_time = 0 -> .use_pmdown_time = 1
- -> .endianness = 1
- -> .non_legacy_dai_naming = 1
adau1781:
xxx_codec_xxx() -> xxx_component_xxx()
.idle_bias_off = 0 -> .idle_bias_on = 1
.ignore_pmdown_time = 0 -> .use_pmdown_time = 1
- -> .endianness = 1
- -> .non_legacy_dai_naming = 1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we can replace Codec to Component. Let's do it.
Note:
xxx_codec_xxx() -> xxx_component_xxx()
.idle_bias_off = 0 -> .idle_bias_on = 1
.ignore_pmdown_time = 0 -> .use_pmdown_time = 1
- -> .endianness = 1
- -> .non_legacy_dai_naming = 1
To keep compatibilty, this patch adds snd_soc_xxx_ac97_codec()
macro. These will be removed when all codec code was removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes the routing path of the power widget "LDO2", and it
should be depended on the hardware design. The power widget "LDO2" should
add the routing path with the MICBIAS in the machine driver that is
reasonable.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For controls marked write-only don't initialize the cache from the
content of the DSP memory. We stil need the cache for any new data
that is written to this control, and we need to return something
for a read of the ALSA control because most user-side code assumes
all ALSA controls are readable. The cache is already created zero-
filled so the only change needed is to skip populating it from
DSP memory if the control isn't readable.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the merge window having been delayed for another week here's
another batch of updates that came in during that week. There's a few
important fixes in here, mainly a fix for I/O on a number of devices
caused by some of the component rework and a fix for a potential issue
if more than one component in a link provides compressed operations.
The I/O fixes are particularly important as the problem causes a power
regression on a number of OMAP platforms.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlp65E4THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Oy1B/9XQd6twiSRfNKtbdujOyvjc8lpZ01n
JYHVySXyL9ZqAnIblM7Or/iXVEtsAVcXgFegF3SLHAY6VF7DQ1pDolnxUtuXOxOj
j+/2Y4wnDGCjXEr0tMoxrbNUIqlVZLCpPwsPo3vvVbr6sLLmQYVposNp2A2sK2bz
uWm9E3Nr26Q0UctzjWQM5+AFHSouyL7zDPfBCoWkEToP7163w6r4JDr991KdNGwP
Ac+5qjRUSldsn8WB2ngm8ioqbq+aOvsz2THYjG8gxrlQK+BWsyCDqF7f1d9GWse2
7k+xZLrdJrVkBMOnpvOx/Y4KRfe9BAFZBZ3KRbi2IR++7TD3902xEX27
=aIRm
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound
Pull more ASoC updates from Mark Brown:
"With the merge window having been delayed for another week here's
another batch of updates that came in during that week.
There's a few important fixes in here, mainly a fix for I/O on a
number of devices caused by some of the component rework and a fix for
a potential issue if more than one component in a link provides
compressed operations. The I/O fixes are particularly important as the
problem causes a power regression on a number of OMAP platforms"
* tag 'asoc-v4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound: (22 commits)
ASoC: stm32: add of dependency for stm32 drivers
ASoC: mt8173-rt5650: fix child-node lookup
ASoC: dapm: fix debugfs read using path->connected
ASoC: compress: Fixup error messages
ASoC: compress: Remove some extraneous blank lines
ASoC: compress: Correct handling of copy callback
ASoC: Intel: kbl: Enable mclk and ssp sclk early
ASoC: Intel: Skylake: Add extended I2S config blob support in Clock driver
ASoC: Intel: Skylake: Add ssp clock driver
ASoC: Fix twl4030 and 6040 regression by adding back read and write
ASoC: sun8i-codec: Add ADC support for a33
ASoC: rockchip: Use dummy_dai for rt5514 dsp dailink
ASoC: soc-pcm: rename .pmdown_time to .use_pmdown_time for Component
ASoC: ak4613: call dummy write for PW_MGMT1/3 when Playback
ASoC: soc-pcm: don't call flush_delayed_work() many times in soc_pcm_private_free()
ASoC: soc-core: snd_soc_rtdcom_lookup() cares component driver name
ASoC: sam9x5_wm8731: Drop 'ASoC' prefix from error messages
ASoC: sam9g20_wm8731: use dev_*() logging functions
ASoC: max98373 Changed SPDX header in C++ comments style
ASoC: dmic: Fix check of return value from read of 'num-channels'
...
Commit 3bb0f7c31b ("ASoC: don't use snd_soc_write/read on twl4030")
caused regressions for both twl4030 and twl6040 as it assumes the
ASoC driver is using regmap. As a side effect, this also causes a
considerable increase in idle power consumption omap3 boards using
twl4030 as the PMIC.
This is because the removal of read and write function pointers
causes some of the ASoC IO functions to not do anything. For example,
snd_soc_register_card() calls snd_soc_dapm_new_widgets() that calls
snd_soc_codec_drv_read() that now does nothing.
A long term solution suggested by Mark Brown <broonie@kernel.org>
is to make the twl drivers use regmap by adding a call to
snd_soc_codec_set_regmap(). This however needs more consideration
as currently the driver internal reads do caching and we would have
both regmap access and internal read/write access accessing the same
hardware registers.
So to fix the regression, let's just do a partial revert adding back
the read and write function pointers. Note that other non-regmap
ASoC drivers may need similar patches.
Fixes: 3bb0f7c31b ("ASoC: don't use snd_soc_write/read on twl4030")
Fixes: 93a00c467f ("ASoC: don't use snd_soc_write/read on twl6040")
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Power Down Release Command (PMVR, PMDAC, RSTN, PMDA1-PMDA6)
which are located on PW_MGMT1 / PW_MGMT3 register must be
write again after at least 5 LRCK cycle or later on each command.
Otherwise, Playback volume will be 0dB.
Basically, it should be
1. PowerDownRelease by Power Management1 <= call 1.x after 5LRCK
1.x Dummy write to Power Management1
2. PowerDownRelease by Power Management3 <= call 2.x after 5LRCK
2.x Dummy write to Power Management3
To avoid too many dummy write, this patch is merging these.
1. PowerDownRelease by Power Management1
2. PowerDownRelease by Power Management3 <= call after 5LRCK
2.x Dummy write to Power Management1/3 <= merge dummy write
This patch adds dummy write when Playback Start timing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 7fb59e940f ("ASoC: codecs: dmic: Make number of channels
configurable") introduces an optional property to the device tree
to specify the number of DMIC channels. dmic_codec_probe() uses
of_property_read_u32() to read the DT value, and expects a return
value of -ENOENT when the property does not exist. This expectation
is incorrect, the actual value returned in this case is -EINVAL (see
of_find_property_value_of_size(), which is called under the hood).
Check for -EINVAL instead.
Fixes: 7fb59e940f ("ASoC: codecs: dmic: Make number of channels configurable")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "check ER1" message is not very clear about its meaning.
Improve it a bit by referring to it as "ER1 erratum" so that it
becomes clearer that ER1 references to a SGTL5000 erratum.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the MCLK is not yet available when the codec is probed, probe
deferral will happen and in this case we should not print an
error message.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 39b5a0f80c ("ASoC: cx20442: don't use reg_cache")
removed .read/.write from driver, but it might breaks non-regmap
driver, because ALSA SoC framework might call it.
To fix this regression, this patch back .read/.write.
and also this patch uses cx20442 internal reg_cache
which is needed for .read/.write.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit c001bf633a ("ASoC: use internal reg_cache on uda1380")
removed .read/.write from driver, but it might breaks non-regmap
driver, because ALSA SoC framework might call it.
To fix this regression, this patch back .read/.write
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit c4305af43a ("ASoC: use internal reg_cache on tlv320dac33")
removed .read/.write from driver, but it might breaks non-regmap
driver, because ALSA SoC framework might call it.
To fix this regression, this patch back .read/.write
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 78f5605c03 ("ASoC: rt5645: cleanup DMI matching code") did a
lot of useful cleanups. This patch adds a default case to enable
jack detection if there is no pdata, device property or quirk.
The chosen jd-mode3 is the most common and should limit the addition
of new DMI-based quirks. Existing DMI quirks which only set this mode
are left as is and not removed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This codec was used in MFLD systems in the PMIC chip, we no longer have
users for this, so remove it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The functions pll_event and dac_event are local to the source and do
not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'pll_event' was not declared. Should it be static?
symbol 'dac_event' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tscs42xx CODEC driver can confuse userspace with non-standard
control names.
Remove "Switch" from enum control type names.
Add "Switch" to on/off control type names.
Signed-off-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMIC DAI driver specifies a number of 1 to 8 channels for each DAI.
The actual number of mics can currently not be configured in the device
tree or audio glue, but is derived from the min/max channels of the CPU
and codec DAI. A typical CPU DAI has two or more channels, in consequence
a single mic is treated as a stereo/multi channel device, even though
only one channel carries audio data.
This change adds the option to specify the number of used DMIC channels
in the device tree. When specified this value overwrites the default
channels_max value of 8 in the snd_soc_dai_driver struct of the codec.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently there is no support for TSCS42xx audio CODECs.
Add support for TSCS42xx audio CODECs.
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to set a corresponding control bit before powering micbias up.
Signed-off-by: Bard Liao <bardliao@realtek.com>
[hdegoede@redhat.com: Remove 2 unused variable declarations]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register "micbias1" and "micbias2" to supply widgets as modern drivers do.
This should not cause any (new) issues for existing users of the codec,
since micbias support is broken anyways. Micbias support needs the
RT5645_MICBIAS?_POW_CTRL_SEL bits in the RT5645_GEN_CTRL2 register to be
updated when enabled/disabled which we currently do not do.
The updating of these bits will be fixed in a follow-up commit.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Teclast X80 Pro tablet needs jd_mode = 3 for headset jack detection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather then doing a dmi_check_system() per possible system use an array
with all known systems, with dmi_system_id.driver_data pointing to the
platform-data for the matching system.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPD pocket has a differential signal microphone and needs in2_diff
to be set to avoid getting a very noisy signal.
Since the GPD pocket and win use the same DMI strings, they share their
platform data-definition, so enabling in2_diff on the pocket also sets
it on the GPD win. The GPD win has a normal microphone, but setting
in2_diff there does not negatively impact the sound from the microphone.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm2200 is the only user of snd_soc_dai::symmetric_rates.
Now, wm2200 is using single DAI on Component.
Thus, wm2200_priv : snd_soc_dai : snd_soc_component are 1 : 1 : 1.
We can replace snd_soc_dai::symmetric_rates on wm2200_priv.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_codec_get_drvdata() is common function to get
private data. Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cannonlake HDMI codec has the same nid as Geminilake. This adds the
vendor id for Cannonlake in hdmi device id list.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct snd_soc_component::dai_drv will be removed soon.
hdac_hdmi is only user of it. Let's keep it on private data.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If an rt5514-spi device is probed but the platform hasn't linked it in,
we might never fully request the SPI IRQ, nor configure the rt5514 DSP,
but we still might try to enable the SPI IRQ (enable_irq_wake()). This
is bad, and among other things, can cause the interrupt to trigger every
time we try to suspend the system (e.g., because the interrupt trigger
setting was never set properly).
Instead of setting our wakeup capabilities in the SPI driver probe
routine, let's wait until we've actually requested the IRQ.
Fixes issues seen on the "kevin" Chromebook (Samsung Chromebook Plus).
Fixes: 58f1c07d23 ("ASoC: rt5514: Voice wakeup support.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
For those which can only get approximation PLL out cases, this patch
will use higher resolution to get a better PLL parameter.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In skylake platform, we hear a loud pop noise(0 dB) at start of
audio capture power up sequence. This patch removes the pop noise
from the recording by adding a delay before enabling ADC.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the first jack detection while booting, the result will always show as
headset, even we insert the headphone.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the code easier to read by using snd_soc_update_bits() over
read/modify/write sequences.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the code easier to read by using snd_soc_update_bits() over
read/modify/write sequences. Also use separate per-register
variables instead of re-using "data". This can prevent accidental
over-writing and makes it clear for which register each bit value is
intended.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify mute function by using snd_soc_update_bits() over
read/modify/write style code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Inter-register definitions should use BIT and GENMASK definitions
and also be grouped by what register they belong to. This makes it
easy to cross-check with the datasheet and is consistent with other
drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the DATALEN bit field requires shifting our value by 4. Setting
the OSR value of the PLL divider also requires a shift by 4. Currently
the code abuses this fact and uses the shift for the divider register to
set the data-length register. Fix this here by using the definition meant
for this register.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the DATATYPE bit field requires shifting our value by 6. Setting
the J value of the PLL also requires a shift by 6. Currently the code
abuses this fact and uses the shift for the PLL register to set the
data-type register. Fix this here by using the definition meant for
this register.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop definition of frequencies that only map from one number to
the same number. This is not needed and if misused can hide
bugs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All register definitions should use the AIC32X4_REG macro, even the ones
in page 0. This makes datasheet lookup more consistent and helps with
alignment both in this file and across other tlv320aic* drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce a custom super-set register map and associated bit definitions
to allow driver access to all TAS5722 device functionality.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TI TAS5722 digital amplifier is very similar to the TAS5720 from an
overall and register map perspective. Therefore the existing driver can be
extended easily to support this additional device. This commit allows
TAS5722 devices to be used in a "subset" type of fashion, without exposing
any of the additional features they offer.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPD win and pocket devices both use the same codec setup and both
have too generic dmi strings making snd_soc_set_dmi_name() not work.
As these devices have only a single speaker we want a separate ucm
file for them, which requires a unique long_name, use the existing
GPD quirk handling to also provide a unique long_name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The checks for whether another region/block header could be present
are subtracting the size from the current offset. Obviously we should
instead subtract the offset from the size.
The checks for whether the region/block data fit in the file are
adding the data size to the current offset and header size, without
checking for integer overflow. Rearrange these so that overflow is
impossible.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add a reset function that toggles the reset line if available or uses
the software reset command otherwise. Use this in power up to ensure the
registers are in a sane state. This is useful when the driver module
is reloaded, or after Kexec, warm-reboots, etc..
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use fwnode_* API instead of of_*, the results are the same but
fwnode_* is cleaner and we get ACPI support.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of gpiod_* needs <linux/gpio/consumer.h>, add this here.
Fixes: b6b247cd5e ("ASoC: tlv320aic31xx: Switch GPIO handling to use gpiod_* API")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pcm186x_dai_ops and pcm186x_adc_input_channel_sel_value are local to the
source and do not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'pcm186x_dai_ops' was not declared. Should it be static?
symbol 'pcm186x_adc_input_channel_sel_value' was not declared. Should it
be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Assignments for start_nid, end_nid and num_nodes of hdac_device
structure are already done in init. So, remove the redundant
assignments.
Signed-off-by: Puneeth Prabhu <puneethx.prabhu@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All nodes of hdmi codec widgets are not updated in sysfs interface
(/sys/bus/hdaudio/devices/<dev>/widgets/) as the vendor widget is not
programmed to enable all the converters and pins during init. So,
refresh the sysfs widget interface after enabling all pins and
converters.
Signed-off-by: Puneeth Prabhu <puneethx.prabhu@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is an initial version of the PCM186x codec driver supporting both
2-channel and 4-channel device variants. Not all device features are
supported yet such as master/slave mode PLL configuration for which the
codec driver currently relies on the PCM186x built-in clock
auto-detection feature or the connection of digital microphones.
However here is what's here and what should work:
- Support for SPI and I2C low-level interfaces
- Regmap support and basic register definitions
- Input Mixer and Mux selection
- I2C, LJ, and TDM DAI format support
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Texas Instruments TAS6424 device is a high-efficiency quad-channel
Class-D audio power amplifier. Its digital time division multiplexed
(TDM) interface enables up to 2 devices to share the same bus,
supporting a total of eight channels from one audio serial port.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AIO on UniPhier can output S/PDIF where no codec is needed.
This patch adds S32_LE support for dummy codec drivers.
If one S/PDIF controller has its own limitation, its CPU DAI driver should
set the supported format by its own circumstance, since the soc-pcm driver
will use the intersection of cpu_dai's formats and codec_dai's formats.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The sequence of crosstalk measurement is not robust. The driver
add more protections to make it stronger. The improvements as follows:
(1)Give backup table the default value. The values are the same
with the default of hardware registers. The impact will decline
once restoring the backup table in the wrong way.
(2)Add xtalk_baktab_initialized flag. The flag can keep the
initiation status of backup table. It helps to backup and restore
the backup-table correctly.
(3)Add cancel parameter in the restore function. The volume ramping
should do in crosstalk DONE state only. Otherwise, the delay action
is not allowed because the restore may happen during the jack
eject interruption.
(4)Add xtalk_protect condition check before scheduling work in ISR.
It makes sure the semaphore hold during the crosstalk measurement.
The sequence is still under protection from playback interference.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After reviewing the crosstalk protection, there are two flaws at
semaphore control. The first one is that the semaphore releases are
not enough; and the other is that down_interruptible has an risk to
make the ISR sleep.
Therefore, the driver add more releases before the funcitons return.
Take down_trylock to replace down_interruptible. The ISR can control
the protection as well and never sleep by semaphore.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently BCLK inverting is only handled when the DAI format is
DSP, but the BCLK may be inverted in any supported mode. Without
this using this CODEC in any other mode than DSP with the BCLK
inverted leads to bad sampling timing and very poor audio quality.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This CODEC supports being the WCLK and/or BCLK slave, add
support for this here.
Also make the alert into an error as alert is more urgent
than needed here and is rarely used.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If our set_sysclk DAI callback has not been called yet p_div will be 0
and dividing by this will cause an error. Print an error message and
leave before this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move to using newer gpiod_* GPIO handling functions. This simplifies
the code and eases dropping platform data in the next patch. Also
remember GPIO are active low, so set "1" to reset.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function aic31xx_device_init() is only called from probe and
does nothing that logically shouldn't be in probe, remove this
unneeded function call and move its code into probe where it was called.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We also move the comments describing the registers to after the register
definition to remove non-uniform vertical white-space, this makes
cross-referencing with the datasheet much easier.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simple non-functional changes including:
* Fix spelling errors
* Reformat code for easier reading
* Remove unneeded code
* Remove assignments that are always overridden
* Normalize function return paths
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-tfa9879.ko | grep alias
alias: i2c:tfa9879
After this patch:
$ modinfo sound/soc/codecs/snd-soc-tfa9879.ko | grep alias
alias: i2c:tfa9879
alias: of:N*T*Cnxp,tfa9879C*
alias: of:N*T*Cnxp,tfa9879
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch renames all the variable instances of hdac_device with hdev
to prepare the code base to remove the usage of hdac_ext_device
data structures done in the following patches. Existing code uses hdev
and hdac as variable names for hdac_device as well as hdac_ext_device,
which creates confusion.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Existing code uses hdac and edev inconsistently to represent
hdac_ext_device structure which creates confusion because hdac
is used even to represent hdac_device. So this patch replaces
all the variable instances of hdac_ext_device with edev.
In the later patch all the variable instances of hdac_device will
be replaced with hdev.
This prepares the code base to remove the usage of hdac_ext_device
data structures done in the subsequent patches.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replaces the direct access of HDMI private data with macro
hdev_to_hdmi_priv in order to prepare the code to remove hdac_ext_device
usage in the subsequent patch.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIO1 control register is number 51, fix this here.
Fixes: bafcbfe429 ("ASoC: tlv320aic31xx: Make the register values human readable")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The return value is not checked, and even if it was there is nothing
we could do about it and messages are already printed.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix header copyright tags, while we are here, also switch to SPDX
and fixup MODULE tags to match.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the crosstalk is disabled, it is better to set clear_irq
properly when the impedance measurement interrupt happens.
It can avoid that the driver clears other IRQs by accident
if the active_irq has another IRQ events.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Reviewed-by: Wu-Cheng Li <wuchengli@chromium.org>
Tested-by: Wu-Cheng Li <wuchengli@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
[Retitled for accuracy -- broonie]
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This codec is configurable for only 16 bit and 32 bit samples, so reflect
this in the supported formats also remove 24bit sample from supported list.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The driver makes the crosstalk funciton disabled by default
which can simplify the codec function. The platform may not
need this funciton and reduce the potential risk. Therefore,
We change the property "nuvoton,crosstalk-bypass" to
"nuvoton,crosstalk-enable". The crosstalk measurement is enabled
if the property is set. Otherwise, it is disabled. Besides,
add more condition in the entry point of the crosstalk sequence
to disable the function completely.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
twl4030 doesn't use regmap nor reg_cache. Its write/read are done
through twl4030_reg_write/read. This driver directly calling these
functions, but sometimes using snd_soc_write/read.
As part of cleanup, snd_soc_codec_driver::write, read will be
removed soon. Then, write/read access through snd_soc_write/read
will doesn't work on this driver, since it doesn't use regmap nor
reg_cache.
This patch replace snd_soc_write/read to twl4030_write/read.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
twl6040 doesn't use regmap nor reg_cache. Its write/read are done
through twl6040_reg_write/read. This driver directly calling these
functions, but sometimes using snd_soc_write/read.
As part of cleanup, snd_soc_codec_driver::write, read will be
removed soon. Then, write/read access through snd_soc_write/read
will doesn't work on this driver, since it doesn't use regmap nor
reg_cache.
This patch replace snd_soc_write/read to twl6040_write/read.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec reg_cache is legacy feature and very few driver only are using
it. But, ALSA SoC framework needs to support it.
Codec will be merged into Component in the future, so, let's remove
legacy and unused feature from framework.
cx20442 is using reg_cache but it is only 1byte, and it doesn't use
snd_soc_write/read/update_bits function which uses reg_cache.
reg_cache user is only debugfs. Let's clean reg_cache for now.
But let's keep .write function since it can be used for new additional
feature. .read will not be used, let's remove.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec reg_cache is legacy feature and very few driver only are using
it. But, ALSA SoC framework needs to support it.
Codec will be merged into Component in the future, so, let's remove
legacy and unused feature from framework.
This patch implements ALSA SoC reg_cache feature into driver,
and don't use ALSA SoC framework's feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec reg_cache is legacy feature and very few driver only are using
it. But, ALSA SoC framework needs to support it.
Codec will be merged into Component in the future, so, let's remove
legacy and unused feature from framework.
This patch implements ALSA SoC reg_cache feature into driver,
and don't use ALSA SoC framework's feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
max98927 driver is using codec hw_write/control_data,
but it is redundant code. This patch cleanup these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
max98926 driver is using codec hw_write/control_data,
but it is redundant code. This patch cleanup these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
twl6040 driver is using codec hw_write/control_data,
but it is redundant code. This patch cleanup these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cx20442/omap-ams-delta driver is using codec hw_write/control_data,
but it is redundant code. This patch cleanup these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
uda1380 driver is using codec hw_write/control_data,
but it is redundant code. This patch cleanup these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
uda1380 driver is using codec hw_write/control_data,
but it is redundant code. This patch cleanup these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the rt5514 spi driver is loaded, but the snd_soc_platform_driver is not
loaded by the correct DAI settings, the NULL pointer will be gotten by
snd_soc_platform_get_drvdata in the resume function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in sound/soc/codecs/snd-soc-pcm512x-spi.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit extra messages for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit extra messages for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Android 3.5mm Headset jack specification mentions that BTN_0 should
be mapped to KEY_MEDIA, but this is less logical than KEY_PLAYPAUSE,
which has much broader userspace support.
For example, the Chrome OS userspace now supports KEY_PLAYPAUSE to toggle
play/pause of videos and audio, but does not handle KEY_MEDIA.
Furthermore, Android itself now supports KEY_PLAYPAUSE equivalently, as the
new USB headset spec requires KEY_PLAYPAUSE for BTN_0.
https://source.android.com/devices/accessories/headset/usb-headset-spec
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit extra messages for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Delete a duplicate character in a word of this description.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch makes sure the DMIC delay will be happened after normal SUPPLY
widgets power on. If there are some platforms that provide the MCLK using
the SUPPLY widget, it will make sure the delay time is helpful.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5645_AD_DA_MIXER (0x29) register will not be reset to default after
SW reset. So we have to write it to its default value in i2c_probe.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent codec node was also prematurely freed,
while the child node was leaked.
Fixes: 2d6d649a2e ("ASoC: twl4030: Support for DT booted kernel")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable <stable@vger.kernel.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent codec node was also prematurely freed.
Fixes: 4d50934abd ("ASoC: da7218: Add da7218 codec driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable <stable@vger.kernel.org>
Change the maximum of FDCO which remains between 90MHz-100MHz.
FDCO must be within the 90MHz-100MHz or the FFL cannot be
guaranteed across the full range of operation.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add these parameters to improve the FLL performance.
The comments show as follows:
(1)ICTRL_LATCH: FLL DSP speed capability control
When FLL running at high frequency with long decimal number, DSP needs
to operate at high speed. FLL DSP can optimize between performance and
power consumption by ICTRL_LATCH.(111 has highest power consumption.)
The default setting can be used to reduce power.
(2)CUTOFF500: loop filter cutoff frequency at 500Khz
It will give the best FLL performance but highest power consumption
to enable the cutoff frequency. FLL Loop Filter enable to reduce FLL
output noise, especially,(DCO frequency)/(FLL input reference frequency)
is not a integer.
(3)GAIN_ERR: FLL gain error correction threshold setting
The threshold is comparison between DCO and target frequency.
The value 1111 has the most sensitive threshold, that is, 1111 can have
the most accurate DCO to target frequency. However, the gain error setting
conditionally and inversely depends on FLL input reference clock rate.
Higher FLL reference input frequency can only set lower gain error, such
as 0000 for input reference from MCLK=12.288Mhz. On the other side, if FLL
reference input is from Frame Sync, 48KHz, higher error gain can apply
such as 1111.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The biggest thing this release has been the conversion of the AC98 bus
to the driver model, that's been a long time coming so thanks to Robert
Jarzmik for his dedication there. Due to there being some AC97 MFD
there's a few fairly large changes in input and the MFD layer, mainly to
the wm97xx driver.
There's also some drivers/drm changes to support the new AMD Stoney
platform, these are shared with the DRM subsystem and should be being
merged via both.
Within the subsystem the overwhelming bulk of the changes is in the
Intel drivers which continue to need lots of cleanups and fixes, this
release they've also gained support for their open source firmware.
There's also some large changs in the core as Morimoto-san continues to
mirror operations into the component level in preparation for conversion
of drivers to that.
- The AC97 bus has finally caught up with the driver model thanks to
some dedicated and persistent work from Robert Jarzmik.
- Continued work from Morimoto-san on moving us towards being able to
use components for everything.
- Lots of cleanups for the Intel platform code, including support for
their open source audio firmware.
- Support for scaling MCLK with sample rate in simple-card.
- Support for AMD Stoney platform.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAloJhwMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0KzbB/9tXryXYz3dnKVlm9rk+Cq0Xy4TrUNk
WY+Il+Di1b6CQJbAm9GSacJxR+siupZCjGC5roHznj/AA2l0RuxJXpxG40Db8ZX+
bDR7mIWtuTUJHazqXltafj9ydElRKVpOGPAi5YJhhW5bXQ3SR9fFy0D3mdcT02v4
SyMExhOMz+mdnuBhbWx9kqJ9LPzCs0ow+R4uoRgAQxpFXPBGtq06sMkK86lGfsl/
iRM36J6FIeIQQfSHG/dkkpoybVax43z4OH7G1IL2FOU7miwkjZh/TTh/xHTd86Mc
OOuGu4hB+MjvccSOa9HSrOqFjxtkZipstwqYVWoYQcUoIVpcg0YRk7TG
=5KBY
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.15
The biggest thing this release has been the conversion of the AC98 bus
to the driver model, that's been a long time coming so thanks to Robert
Jarzmik for his dedication there. Due to there being some AC97 MFD
there's a few fairly large changes in input and the MFD layer, mainly to
the wm97xx driver.
There's also some drivers/drm changes to support the new AMD Stoney
platform, these are shared with the DRM subsystem and should be being
merged via both.
Within the subsystem the overwhelming bulk of the changes is in the
Intel drivers which continue to need lots of cleanups and fixes, this
release they've also gained support for their open source firmware.
There's also some large changs in the core as Morimoto-san continues to
mirror operations into the component level in preparation for conversion
of drivers to that.
- The AC97 bus has finally caught up with the driver model thanks to
some dedicated and persistent work from Robert Jarzmik.
- Continued work from Morimoto-san on moving us towards being able to
use components for everything.
- Lots of cleanups for the Intel platform code, including support for
their open source audio firmware.
- Support for scaling MCLK with sample rate in simple-card.
- Support for AMD Stoney platform.
I've been quite lax in sending these due to conference season but here's
a fairly large collection of ASoC updates. The one thing that's not
device specific is Takashi's fix for races between delayed work and PCM
destruction, otherwise everything is specific to an individual device.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlnx7QsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0H6gB/9Kg6nfaNQDH3ScDO/0KXJevvc9DZUG
1Mgb6o866WQKVKwHL4/7PeUnwpaAh/Dr5KN7bFS7nImrZlHiJfv64Cmrrca+VMwa
O9SnAxbzMDN1MXV3uLDlmd5jJ2EETGnSSo31gjyOuFAmvWRYhtvN4QtoLRBQYYJ9
A32JAKYXKpdjYlIq8sssf1Ey9OcReho3klAc578Yw5qsuHTsB8yJ5SNy0YgmobCm
rNs+LcY9fBPQxY1nVW5iJ3L8oR9RXlUOdZy1I220i0q6+ku1nynbh64V8m7fFGmp
KQLIVvH8JGlqaGBidU47C3vwEnUN88y0+98i9dF4Hc26E+Ml3YNyL/z6
=TVgt
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAloGGn8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BAsB/9tbgkbKpUVsWEQOTXDtz1VARb5+zxJ
zMRmYGdcfV+au4pmo07NwcxwFDqeLxmsd7dRM+eoPJGbxklD9rr9eL9tZiO1TI0B
jla9eyKO1aRjCD8dEDsQJEUjDGWWbrpYRvFjlTmYW5cf1vgE9Ta7QtwBN+mK+Ssn
1PtwfHg5lDffoCMGOgu/5Kah4QhzAIU1mM4Vg77VgsuScZEw5qMYJUncfkdsH6M5
JiQJpOQR/wNL4/IETodjhFzqhi9vlUvDEfmATNMpHMdHA//erUbphUt2bAjqVauM
zKTFTSN1vvW1GirJyxz4NiHXQ6upbpZPMDcPsfOzJhHw82OAwx/pp1QT
=bBtM
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.14-rc6' into asoc-linus
ASoC: Fixes for v4.14
I've been quite lax in sending these due to conference season but here's
a fairly large collection of ASoC updates. The one thing that's not
device specific is Takashi's fix for races between delayed work and PCM
destruction, otherwise everything is specific to an individual device.
# gpg: Signature made Thu 26 Oct 2017 15:11:23 BST
# gpg: using RSA key ADE668AA675718B59FE29FEA24D68B725D5487D0
# gpg: issuer "broonie@kernel.org"
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>" [unknown]
# gpg: aka "Mark Brown <broonie@debian.org>" [unknown]
# gpg: aka "Mark Brown <broonie@kernel.org>" [unknown]
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>" [unknown]
# gpg: aka "Mark Brown <broonie@linaro.org>" [unknown]
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
The main rt5514 driver optionally calls into the SPI back-end to load
the firmware. This causes a link error when one driver selects rt5514
as built-in and another driver selects rt5514-spi as a loadable module:
sound/soc/codecs/rt5514.o: In function `rt5514_dsp_voice_wake_up_put':
rt5514.c:(.text+0xac8): undefined reference to `rt5514_spi_burst_write'
As a workaround, this adds another silent symbol, to force rt5514-spi
to be built-in for that configuration. I'm not overly happy with
that solution, but couldn't come up with anything better. Using
'IS_REACHABLE()' would break the case that relies on the loadable
module, and all other ideas would result in more complexity.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new functions are only used when CONFIG_PM is enabled,
leading to a harmless warning:
sound/soc/codecs/rt5514-spi.c:474:12: error: 'rt5514_resume' defined but not used [-Werror=unused-function]
sound/soc/codecs/rt5514-spi.c:464:12: error: 'rt5514_suspend' defined but not used [-Werror=unused-function]
This marks them as __maybe_unused to make the build silent
again.
Fixes: 58f1c07d23 ("ASoC: rt5514: Voice wakeup support.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check the JD status in the button pushing to prevent the IRQ that is locked
by button pushing event while the jack unpluging.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Minimum time required between power On of codec and read
of RT5645_VENDOR_ID2 is 400msec. We should wait that long
before reading the value.
TEST=Cold boot the device and check for sound device.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP modes are documented in the data sheet but not enabled in the driver.
The work-around already implemented for DA7218/9 is also required to
make sure the bit clock handling in DSP modes follows ASoC conventions.
Tested with ARD-AUDIO-DA7212 and Minnowmax Turbot boards
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the probe, the codec may not be ready for I2C reading or there are some
glitches on the i2c line. So if the i2c reading value is incorrect, it will
read again after delay. This issue is similar the patch
https://patchwork.kernel.org/patch/9681421/. In current project, these 2
devices were connected to the same i2c line, and they met the same problem.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For wake on voice use case, we need to copy data from DSP buffer
to PCM stream when system wakes up by voice. However the edge
triggered IRQ could be missed when system wakes up, in that case
the irq function will not be called. If the substream was constructed
beforce suspend, we will schedule data copy in resume function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the rt5514 Wake on Voice device is opened while suspended, it will
be able to wake up the system when a voice command is detected.
This patch also supports user-space policy to override wakeup behavior
by /sys/bus/spi/drivers/rt5514/spi2.0/power/wakeup.
Signed-off-by: Chinyue Chen <chinyue@chromium.org>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 402005
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115168
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 146568
Addresses-Coverity-ID: 146569
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115164
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1195220
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 146566
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397957
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During failure, widgets in cvt_list and pin_list are not freed. So fix
the possible memory leak by freeing them when failure occurs.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pointers hdac_hdmi_pcm and hda_device_id can be NULL, so add check for
valid pointer to avoid NULL pointer dereference.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snprintf instead of sprintf to shut the warning.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch lets the buf_size to align with period_bytes to prevent the
buffer reading over the real size of the DSP buffer and also avoid to
calculate the wrong size of remaining data.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's difficult for me to handle upstream mail that ends up in my work
account and this was done outside of work anyway so replace my work
address with my usual address for upstream stuff.
Signed-off-by: Mark Brown <broonie@kernel.org>
There are headphone and speaker outputs in NAU88L24. During the
playback, the codec should not change the clock status when
switching these outputs.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is possible to get the fake key press interruption when the codec
do jack detection. We think it's proper to move the key interruption
configuration after jack detection done.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the record starts, the driver turns on MICBIAS and the voltage is
pulled up for an instant. If the receiver starts to capture the signal
between the instant, there is an pop noise in the stream beginning.
To avoid the pop noise, the driver makes a delay in the sequence.
After MICBIAS powered up, the driver waits 300 ms for the voltage
going down. Then turns on the ADC output, and sends signal to receiver.
The pop noise can be erased.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change channel PGA input mode selection for better recording quality.
The patch shorts the inputs to ground with 12kOhm differentially
terminated.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The four channel ADCs in NAU85L40 have difference control registers,
it is hard to synchronous these four channels without correct sequence.
The phase difference will not be a constant and not to conjecture easily.
It may be 2.55 degree, or more ,or less.
Intended to prevent phase difference of channels, the solution as follows:
(1)Channel_Sync need to be enabled.
(2)Do soft reset without affecting register when recording done.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the option for the DSP clock that can be calibrated by the other clock
source.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After checking the code and the datasheet, it seems like we are handling
the clock inversion (SND_SOC_DAIFMT_NB_IF and SND_SOC_DAIFMT_IB_IF) not
correctly.
>From the datasheet (Table 58):
R5 Format Control, BITS[5:4], [BCP:LRP]:
(0) 00 = normal BCLK, normal LRCLK
(1) 01 = normal BCLK, inverted LRCLK <-- Fix this
(2) 10 = inverted BCLK, normal LRCLK
(3) 11 = inverted BCLK, inverted LRCLK <-- Fix this
Signed-off-by: Sergej Sawazki <sergej@taudac.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch fixed that the ACPI cannot access the device property from the
function rt5514_parse_dp().
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"SPOL MIX DAC R1 Switch" and "SPOL MIX SPKVOL R Switch" are only
exist in the early version of rt5645.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The KIANO SlimNote 14.2 laptop uses the JD1_1 input pin for jack
detection. Set the correct quirk in the codec driver.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rework a bit the quirk logic in the codec driver to simplify the
DMI-based quirk assignment for non-DT platforms.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable jack detection for the RT5651 codec on the JD* pins.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for unconditionally passing the struct timer_list
pointer to all timer callbacks, switch to using the new timer_setup()
and from_timer() to pass the timer pointer explicitly. These are all the
"mechanical" changes remaining in the sound subsystem.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable jack detection for the RT5651 codec on the JD* pins.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MICBIAS widget type has been deprecated. Convert it to a SUPPLY widget.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value of register 0x91 is 0x0c00 instead of 0x0000.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_pll function to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_sysclk to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the old AC97 is not used, CONFIG_SND_SOC_AC97_BUS is not
defined. As a consequence, in the error path, snd_soc_free_ac97_codec()
is not defined and triggers a compilation error.
Fix it for wm9705 and wm9712, as wm9713 is correctly written.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return proper error instead of 0 if the revision does not match.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The macro used to set the microphone bias level causes the
snd_soc_write() call to overwrite other fields in the CDC_A_MICB_1_VAL
register. The macro also does not return the proper level value
to use. This fixes this by preserving all bits from the register
that are not the level while setting the level.
Signed-off-by: Jean-François Têtu <jean-francois.tetu@savoirfairelinux.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The very first time a headset is plugged in, detection is unreliable
because bias hasn't been configured yet, it's done once a mechanical
insertion interrupt has been triggered, so following insertions (and
thus detections) are not affected.
To fix the very first detection, the bias must also be configured in the
function that setup the MBHC. Move pm8916_wcd_setup_mbhc after
pm8916_mbhc_configure_bias to avoid a forward declaration.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo snd_soc_msm8916_analog | grep alias
$
After this patch:
$ modinfo snd_soc_msm8916_analog | grep alias
alias: of:N*T*Cqcom,pm8916-wcd-analog-codecC*
alias: of:N*T*Cqcom,pm8916-wcd-analog-codec
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd-analog uses button0 to differentiate between headphone and
headset. Under some circumstances, button pressed and released
interrupts are not fired as the driver expects it.
For instance, with some connectors, there are spurious button-pressed
interrupts when unplugging a headphone, without the corresponding
button-released interrupt. But the codec always alternates between
button pressed and released interrupts, it cannot fire two interrupts of
the same kind in a row. That means that when the headphone is plugged
back, only a button-released interrupt will be fired instead of pressed
then released. This causes the driver to report headphone as headset.
By changing the logic and relying on button 0 release interrupt, the
driver could be made more robust for connectors that differ from the one
used on the Dragonboard's audio mezzanine.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to set a specific bit for 50 bclk rate. So add set_bclk_ratio
function to set the bit.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The kcontrol for the third input (rxN_mix1_inp3) of both RX2
and RX3 mixers are not using the correct control register. This simple
patch fixes this.
Signed-off-by: Jean-François Têtu <jean-francois.tetu@savoirfairelinux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Additional checks exposed a mistake in the quirk for the Dell Venue
Pro 5855 (Dmic2 instead of Dmic1). Rather than adding quirk tables,
merge all quirks in a single table and use flags to differentiate
platforms. Also add a parameter override to help support additional
platforms using this codec
CC: Bard Liao <bardliao@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the irq handler "rt5663_irq", while the codec is not initialized,
rt5663->codec will be null, and it will cause the kernel panic in the debug
print enabled.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, wm8998 has two input mux controls on IN1 and attempts to
switch these together when the A position is configured to be in digital
mode. This is because the digital mode requires pins from both the L and
R channels. However, this doesn't work as intended because whilst the
registers on the chip are changed the corresponding DAPM
representation is only updated for the mux actually being changed by the
user. The DAPM graph being out of sync with the hardware can cause some
odd issues with incorrect things being powered etc.
To avoid this issue and simplify the code somewhat, simply let the user
set the muxes as they desire. If they set an invalid configuration they
might not get audio from the DMIC but most of the chip requires you to
set a valid audio route to get audio.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The output volume limits allow signals to be limited to specific levels
appropriate for the hardware attached. As this is a property of the
hardware itself these will be configured through device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't use BUG_ON() for a non-critical sanity check on production
systems. This patch replaces with a softer WARN_ON() and an error
path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Even though the tfa9879 driver can probe via device tree trough the
I2C core code, it is preferable to have explicit device tree
bindings instead [1], so add this support.
[1] https://www.spinics.net/lists/devicetree/msg195176.html
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the read-only arrays div and pd on the stack,
instead make them static const. Makes the object code smaller by 210 bytes:
Before:
text data bss dec hex filename
2869 720 0 3589 e05 sound/soc/codecs/rl6231.o
After:
text data bss dec hex filename
2495 880 0 3375 d2f sound/soc/codecs/rl6231.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a private data structure. This is a preparation for a codec which
would need an another data on top of snd_ac97, which will be the case
when an MFD wm97xx device will probe wm9705.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently all the audio related device tree entries are handled by the
MFD code, for most parts of the Arizona driver we group the device
tree handling with the component that uses it and should do so here as
well.
Add handling in the ASoC code for the audio device tree entries, a
later patch removes the MFD side handling but there is no harm in it
being duplicated temporarily.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver has quite a few small initialisation functions, in
preparation for some refactoring add a new function arizona_init_common.
This will be used bus probe level initialisation that is common across
Arizona devices. For now just move the notifier chain initialisation in
there.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the acpi match table for the ts3a227e audio accessory
detection device. This enables headset features like jack plug/unplug
notifications, mic presence, and button pressed events.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
'commit b8a3ee820f ("ASoC: max98090: Add recovery for PLL lock failure")'
enabled a workaround PLL unlocked issues, but generates annoying
dev_info "PLL unlocked" messages at a 10ms rate, usually on startup.
Move to dev_info_ratelimited. This issue doesn't seem to impact audio
functionality. This trace is commented out in the GalliumOS patches,
it's better to keep it to check on potential quality issues
Tested on Lenovo 100s (Baytrail Chromebook)
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support the function of impedance sensing. It could be set the matrix row
number of the impedance sensing table and the related parameters in the
DTS.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use FIELD_SIZEOF rather than declaring and initializing hcp. Remove
unused variables. Cleans up clang warning:
warning: Value stored to 'hcp' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These dmi_system_id structures and associated platform data are
never modified so they can be marked const.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Bard Liao <bardliao@realtek.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
--
sound/soc/codecs/rt5645.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit eb33869c72 ("ASoC: rt5514: Guard Hotword Model bytes
loading") and commit d18420b0a0 ("ASoC: rt5514: expose Hotword Model
control")
It is discouraged to use SND_SOC_BYTES_TLV to load arbitrary bytes from
userspace to driver. Removing the 'Hotword Model' control until we have
a good way to verify the content of hotword model blobs.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
For wake on voice use case, we need to copy data from DSP buffer
to PCM stream when system wakes up by voice. However the edge
triggered IRQ could be missed when system wakes up, in that case
the irq function will not be called. Fix that by checking the irq
status bit and schedule data copy accordingly.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This macro is useful to avoid link error on 32-bit systems.
We have the same definition in two drivers, so move it to
include/linux/kernel.h
While we are here, refactor DIV_ROUND_UP_ULL() by using
DIV_ROUND_DOWN_ULL().
Link: http://lkml.kernel.org/r/1500945156-12907-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
The ADC in the ADAU1361 (and possibly other Analog Devices codecs)
exhibits a cyclic variation in the noise floor (in our test setup between
-87 and -93 dB), a new value being attained within this range whenever a
new capture stream is started. The cycle repeats after about 10 or 11
restarts.
The workaround recommended by the manufacturer is to toggle the ADOSR bit
in the Converter Control 0 register each time a new capture stream is
started.
I have verified that the patch fixes this problem on the ADAU1361, and
according to the manufacturer toggling the bit in question in this manner
will at least have no detrimental effect on other chips served by this
driver.
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add break keyword to all switch case unless the case is returning.
Also remove gpio check for consistency.
Signed-off-by: Li Xu <li.xu@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of warning fixes for the newly added CS43130 driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlmtesYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JAOB/9AoBjdVjBNuAm1Wbbx4/HNa+8AbptV
bEgyg7DAP9Dua0XxZqDikm14LdD1iOUziQRJcMzm0ooqdVgNR3gD3GyMuj5EJhtb
5ov27XHD5jHkgZaOUtLke2IeK2NuvC0v3ik3iMMcc37Z9p+zTzjemVUpgxYZk6Fe
jGo/efNFPmHyoD05XIqnRoTeDEQNojRVYKzEcxg2KJhsLi0zCRdxsbWkt+X6fw/Z
b/UXIfpcRvogc2Qsm+tngmyN+oN05zKItUQKU8WUfexp7gI6BBNfs49un+NDgfp1
r0YLMWGhKcjwtw3J3Fp1Nq1lfi8Hbl7+EXJCADDlACFA03A1pKeiuX8C
=4ibF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.14-cs43130' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for the CS43130 driver
A couple of warning fixes for the newly added CS43130 driver.
Add __maybe_unused prefix for addressing the following warnings:
sound/soc/codecs/cs43130.c:2615:12: warning: ‘cs43130_runtime_resume’ defined but not used [-Wunused-function]
sound/soc/codecs/cs43130.c:2596:12: warning: ‘cs43130_runtime_suspend’ defined but not used [-Wunused-function]
Fixes: 8f1e5bf9b4 ("ASoC: cs43130: Add support for CS43130 codec")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As compiler spotted out, there is the potential NULL-dereference in
the code when dc-measure OF is given for other than 43130/43131:
sound/soc/codecs/cs43130.c:2089:18: warning: ‘hpload_seq’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Warn it and return before triggering Oops.
Fixes: 8f1e5bf9b4 ("ASoC: cs43130: Add support for CS43130 codec")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Trivial fix to spelling mistake in variable name
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of fixes, one for a regression in simple-card introduced during
the merge window that was only reported this week and another for a
regression in registration of ACPI GPIOs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlmn+AUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0FTNB/9mqEy0JFFxpr5K5z9YxgXIqJTtIcEV
IoWyrPsZauGYN1OV1ozD6Fih9ZXM4Mp9zZ3UupY3WidSDJksz89r2eLUSCeXPMHL
lY/Cpbq4/4ZVQVXZIY0UskbYqXQrbcadSyQqrX/EfvP5qQwMN5DVvRg4GlAKdTE0
kPVnOOcpEnHbFk3r5hEqRa9zynFog0xGwO45G8mHtEjOstrPNECBELdfc3sUqt55
PGQPMaNWLRK7mk/EmT2hEcAZx0U9IFXkZ0vymqhVnxZ6pyZEu8YRrzW9oulmHdvU
G+KTm/LqcyzEzQTYFI7VxukOd84MT+xwN/2bHNm0ViAdo8xruhkMU3rH
=ag+w
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.13-rc7' into asoc-linus
ASoC: Fixes for v4.13
A couple of fixes, one for a regression in simple-card introduced during
the merge window that was only reported this week and another for a
regression in registration of ACPI GPIOs.
# gpg: Signature made Thu 31 Aug 2017 12:50:29 BST
# gpg: using RSA key ADE668AA675718B59FE29FEA24D68B725D5487D0
# gpg: issuer "broonie@kernel.org"
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>" [unknown]
# gpg: aka "Mark Brown <broonie@debian.org>" [unknown]
# gpg: aka "Mark Brown <broonie@kernel.org>" [unknown]
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>" [unknown]
# gpg: aka "Mark Brown <broonie@linaro.org>" [unknown]
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
It is still using old driver style, this patch also
fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is still using old driver style, this patch also
fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is still using old driver style, this patch also
fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Cirrus Logic CS43130 codec.
Support:
I2S/DSP PCM playback.
DoP/DSD playback.
HP detection and DC/AC impedance measurement.
Signed-off-by: Li Xu <li.xu@cirrus.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of fixes, one for a regression in simple-card introduced during
the merge window that was only reported this week and another for a
regression in registration of ACPI GPIOs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlmn+AUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0FTNB/9mqEy0JFFxpr5K5z9YxgXIqJTtIcEV
IoWyrPsZauGYN1OV1ozD6Fih9ZXM4Mp9zZ3UupY3WidSDJksz89r2eLUSCeXPMHL
lY/Cpbq4/4ZVQVXZIY0UskbYqXQrbcadSyQqrX/EfvP5qQwMN5DVvRg4GlAKdTE0
kPVnOOcpEnHbFk3r5hEqRa9zynFog0xGwO45G8mHtEjOstrPNECBELdfc3sUqt55
PGQPMaNWLRK7mk/EmT2hEcAZx0U9IFXkZ0vymqhVnxZ6pyZEu8YRrzW9oulmHdvU
G+KTm/LqcyzEzQTYFI7VxukOd84MT+xwN/2bHNm0ViAdo8xruhkMU3rH
=ag+w
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.13
A couple of fixes, one for a regression in simple-card introduced during
the merge window that was only reported this week and another for a
regression in registration of ACPI GPIOs.
The MINIX NEO Z83-4 and MINIX NEO Z83-4 Pro devices requires jd_mode=3
to make the jack detection work. Using a BIOS DMI product of "Z83-4"
will match both devices of 'NEO Z83-4' and 'Z83-4 Pro'.
Signed-off-by: Ian W Morrison <ianwmorrison@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In aic3x class of devices Output Common-Mode Voltage can be configured for
better analog performance.
The OCMV value depends on the Analog and digital domain power supply
voltage configuration.
The default OCMV of 1.35V gives best performance when AVDD is around 2.7V
and DVDD is 1.525V, but for higher AVDD/DVDD higher OCMV setting is
recommended.
The patch gives an automatic way of guessing the best OCMV which can be
overwritten by a DT parameter if needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the hdmi i2s playback stream and hdmi spdif playback stream
are using the same name. So when they are enabled at the same time,
kernel will print this warning:
[ 2.201835] hdmi-audio-codec hdmi-audio-codec.1.auto: ASoC: Failed to
create Playback debugfs file
Assign different names to them to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec initialize takes some time when 3.5mm jack plugged in. Add a
delay to report jack plugged event to user space to avoid pop noise.
Signed-off-by: Hsinyu Chao <hychao@chromium.org>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ACPI id for Intel platform.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the PLL involves the calculation of a fixed point ratio
with 4 decimal digits fraction, referred to as "J.D". The
fraction "D" is stored separately from the integer part "J"
and is limited to 0..9999.
The current algorithm uses integer registers to calculate the
fraction part, but failed to compensate for rounding errors,
resulting in values larger than 9999 for the fraction part
occasionally, e.g. for 44.1kHz audio rate and pll_clkin =
3763400 it would set J to 11 and D to 10002, which will at
best result in wrong pitch.
The critical part is the "pll_clkin / 10000", which would be
ok with real numbers, but using integer arithmetic the rounding
decreases the divisor, thus increasing the final quotient.
The issue is solved by linear interpolation over the reciprocal
function between the two adjacent points with integer divisor,
i.e. pll_clkin / 10000 and pll_clkin / 10000 + 1, and doing
all rounding to the lower result.
As a side effect to the bug fix, the approximation to the
desired frequency is much better, for the above mentioned
example we get 11.9993, while the true ratio is 11.9993623.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the rt5514-spi driver is not enabled in kernel, hotword model will
not be loaded when "DSP Voice Wake Up" is set to turn on DSP mode, and
an error is logged instead.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are a lot of typo about semaphore in the comment.
Correct it from semaphone to semaphore.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We're keeping in a good shape, this batch contains just a few small
fixes (a regression fix for ASoC rt5677 codec, NULL dereference and
error-path fixes in firewire, and a corner-case ioctl error fix for
user TLV), as well as usual quirks for USB-audio and HD-audio.
-----BEGIN PGP SIGNATURE-----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=Sqtt
-----END PGP SIGNATURE-----
Merge tag 'sound-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into asoc-rt5677
sound fixes for 4.13-rc7
We're keeping in a good shape, this batch contains just a few small
fixes (a regression fix for ASoC rt5677 codec, NULL dereference and
error-path fixes in firewire, and a corner-case ioctl error fix for
user TLV), as well as usual quirks for USB-audio and HD-audio.
Not all devices with ACPI and this combination of sound devices will
have the required information provided via ACPI. Reintroduce the I2C
device ID to restore sound functionality on on the Chromebook 'Samus'
model.
[ More background note:
the commit a36afb0ab6 ("ASoC: rt5677: Introduce proper table...")
moved the i2c ID probed via ACPI ("RT5677CE:00") to a proper
acpi_device_id table. Although the action itself is correct per se,
the overseen issue is the reference id->driver_data at
rt5677_i2c_probe() for retrieving the corresponding chip model for
the given id. Since id=NULL is passed for ACPI matching case, we get
an Oops now.
We already have queued more fixes for 4.14 and they already address
the issue, but they are bigger changes that aren't preferable for the
late 4.13-rc stage. So, this patch just papers over the bug as a
once-off quick fix for a particular ACPI matching. -- tiwai ]
Fixes: a36afb0ab6 ("ASoC: rt5677: Introduce proper table for ACPI enumeration")
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This change exposes mixer control 'Hotword Model' for switching
hotword model in runtime. This new function requires updated
firmware to load hotword model at address 0x4ff80000.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static checkers complain that unsigned int val is always >= 0. The
context is that snd_soc_read() returns -1U on error. This is harmless
because we're checking that CDC_A_MBHC_RESULT_1_BTN_RESULT_MASK is not
set, and it will always be set for -1U. I could have just removed the
check against -1 but I preserved it because I thought it helped with
readability.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these const as they are only used during a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct rt5645_platform_data s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct rt5645_platform_data s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jack is not detected by default, using jdmode=3 works fine
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix jack detection and dmic setup
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8524 doesn't register platform, unregister platform is not needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5670 codec driver and its machine driver for Intel CHT assume the
implicit GPIO mapping on the index 0 while BIOS on most devices don't
provide it. The recent commit f10e4bf663 ("gpio: acpi: Even more
tighten up ACPI GPIO lookups") restricts such cases and it resulted in
a regression where the headset jack setup fails like:
rt5670 i2c-10EC5672:00: ASoC: Cannot get gpio at index 0: -2
rt5670 i2c-10EC5672:00: Adding jack GPIO failed
For fixing this, we need to provide the GPIO mapping explicitly in the
machine driver. Also this patch corrects the string to be passed to
gpiolib to match with the pre-given mapping, too.
Fixes: f10e4bf663 ("gpio: acpi: Even more tighten up ACPI GPIO lookups")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=115531
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MBHC (MultiButton Headset Control) support is available in pm8921 in two
blocks, one to detect mechanical headset insertion and removal and other
block to support headset type detection and 5 button detection and othe
features like impedance calculation.
This patch adds support to:
1> Support to NC and NO type of headset Jacks.
2> Mechanical insertion and detection of headset jack.
3> Detect a 3 pole Headphone and a 4 pole Headset.
4> Detect 5 buttons.
Tested it on DB410c with Audio Mezz board with 4 pole and 3 pole
headset/headphones.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds bindings in DT to provide required micbias voltage which
could be specific to board. With this new binding, now the mic bias
voltage is left at hardware default value if the device tree does not
specify any mic bias voltage value. Correct micbias value is required
for mbhc buttons to work.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_ops are not supposed to change at runtime. All functions
working with snd_soc_dai_ops provided by <sound/soc-dai.h> work with
const snd_soc_dai_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these two structure variables const as they are either used in a
copy operation or passed to devm_snd_soc_register_component having the
corresponding argument as const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
on some board use enable pin to control dmic start and stop,
so add this feature in dmic driver.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these const as they are only stored in the compr_ops field of a
snd_soc_platform_driver structure, which is of type const.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These snd_soc_dai_ops structures are only stored in the ops field of
a snd_soc_dai_driver structure, which is const. Thus, the
snd_soc_dai_ops structures can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
These snd_soc_dai_ops structures are only stored in the ops field of
a snd_soc_dai_driver structure, which is const. Thus, the
snd_soc_dai_ops structures can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function hdmi_codec_eld_chmap and arrays hdmi_codec_stereo_chmaps
and hdmi_codec_8ch_chmaps are local to the source and do not need to
be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'hdmi_codec_eld_chmap' was not declared. Should it be static?
symbol 'hdmi_codec_stereo_chmaps' was not declared. Should it be static?
symbol 'hdmi_codec_8ch_chmaps' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these const as they are either passed as the 2nd argument to the
function devm_snd_soc_register_platform or snd_soc_register_platform,
and the arguments are of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch fine tunes for the headphone output pop sound.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The array aud96p22_dt_ids is local to the source and does not need to be
in global scope, so make it static.
Cleans up sparse warning:
symbol 'aud96p22_dt_ids' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The array rt5514_dai is local to the source and does not need to be in
global scope, so make it static.
Cleans up sparse warnings:
symbol 'rt5514_dai' was not declared. Should it be static?
warning: symbol 'rt5514_dai' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
max98926_spk_tlv and max98926_current_tlv are local to the source and do
not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'max98926_spk_tlv' was not declared. Should it be static?
symbol 'max98926_current_tlv' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mask rather than the shift is accidentally passed to the
SOC_ENUM_SINGLE macro which results in the wrong bits being set for this
control, change to using the shift to correct this.
Signed-off-by: Sapthagiri Baratam <sapthagiri.baratam@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch move the codec reset code from dai ops to codec probe, so
that the codec is not held in reset when headset detection block is
still active.
Without this patch the codec block will be in reset as long as its not
actively used, which means headset events will not be functional if the
codec dai is not actively used. Point to note is that the headset
detection blocks will work in low power when there is no active audio
usecase and switch to micbias source when audio usecase is active.
Existing dapms should put the codec in low power state anyway when there
is no audio usecase.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_soc_codec_driver structures as const as they are only passed
as an argument to the function snd_soc_register_codec. This argument is
of type const, so declare the structures with this property as const.
In file codecs/sn95031.c, snd_soc_codec_driver structure is also used in
a copy operation along with getting passed to snd_soc_register_codec.
So, it can be made const too.
Done using Coccinelle:
@match disable optional_qualifier@
identifier s;
position p;
@@
static struct snd_soc_codec_driver s@p={...};
@good1@
identifier match.s;
position p;
@@
snd_soc_register_codec(...,&s@p,...)
@bad@
identifier match.s;
position p!={match.p,good1.p};
@@
s@p
@depends on !bad disable optional_qualifier@
identifier match.s;
@@
static
+const
struct snd_soc_codec_driver s={...};
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the ASRC case, there is the noise if the clock is asynchronous with the
LRCK. The default settings will eliminate the noise.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_offset needs reset every time otherwise for consecutive PCM
open the last dma_offset value will cause incorrect pointer position
be reported to user space.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes a missing selection of DMIC in CIC filter source path
to dapm route. Without this patch dmic is not functional.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to set_sysclk() which can let the sound
card driver to set default mclk rate. In this case MCLK for
internal audio codec is expected to be at 9.6MHz by default.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to set_sysclk() which can let the sound
card driver to set default mclk rate. In this case MCLK for
internal audio codec is expected to be at 9.6MHz by default.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch seprates the DC offset between headphone and headset.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to use dev_dbg instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ARRAY_SIZE(bclk_ratios) returns 7 for current code, then it cannot catch
the error if "no matching BCLK/fs ratio". Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch add the sanity checks of the buffer related address to make sure
the addresses are valid.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds the delay time to correct the calibration.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register of setting back ratio should be RT5665_ADDA_CLK_2
instead of RT5665_ADDA_CLK_1.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_OF is disabled, we run into a build error:
sound/soc/codecs/wm8524.c:257:21: error: 'wm8524_of_match' undeclared here (not in a function); did you mean 'wm8524_dai'?
This removes the unnecessary #ifdef around the match table.
Fixes: 007b6a54c3 ("ASoC: codecs: add wm8524 codec driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
WM8524 is a 24-bit 192KHz stereo digital/analog converter (DAC) with
integral charge pump and a simple hardware control interface.
Product information can be found at:
https://www.cirrus.com/products/wm8524/
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wrong bit is assigned to DIG_CLK_CTL_RXD3_CLK_EN, change it for the
correct one.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some ADC L/R Muxes share the some control bit. So, merge them.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_codec .cache_bypass related operation code has been removed.
Let's remove remaining code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch uses the macro IS_ENABLED to make sure that the SPI function also
supports the module build.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
acpi_device_id are not supposed to change at runtime. All functions
working with acpi_device_id provided by <acpi/acpi_bus.h> work with
const acpi_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
acpi_device_id are not supposed to change at runtime. All functions
working with acpi_device_id provided by <acpi/acpi_bus.h> work with
const acpi_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
acpi_device_id are not supposed to change at runtime. All functions
working with acpi_device_id provided by <acpi/acpi_bus.h> work with
const acpi_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
acpi_device_id are not supposed to change at runtime. All functions
working with acpi_device_id provided by <acpi/acpi_bus.h> work with
const acpi_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MONOVOL Playback Volume is a playback volume control on "MONOVOL MIX".
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit a729526720 ("ASoC: sgtl5000: add avc support") the
following kernel crash happens after running a 'reboot' command:
ALSA: Storing mixer settings...
[ 20.031604] Unable to handle kernel paging request at virtual address fffffffe
[ 20.039268] pgd = de2a0000
[ 20.041999] [fffffffe] *pgd=8fffd861, *pte=00000000, *ppte=00000000
[ 20.048387] Internal error: Oops: 80000007 [#1] SMP ARM
The function that takes a kcontrol parameter and returns the
codec that registered the control is snd_soc_kcontrol_codec(),
so use the correct function to fix the problem.
Fixes: a729526720 ("ASoC: sgtl5000: add avc support")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can sleect the i2s clock source for each i2s bus in master mode.
The choice is depended on the HW design and the use case.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TDM docking mode can share the bus to other devices simultaneously.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two variables that have never been used.
sound/soc/codecs/rt5677.c:785:35: warning: ‘in_vol_tlv’ defined but not used [-Wunused-const-variable=]
static const DECLARE_TLV_DB_SCALE(in_vol_tlv, -3450, 150, 0);
sound/soc/codecs/rt5677.c:783:35: warning: ‘out_vol_tlv’ defined but not used [-Wunused-const-variable=]
static const DECLARE_TLV_DB_SCALE(out_vol_tlv, -4650, 150, 0);
Simple remove them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake HDMI codec has the different vendor nid. This patch adds the
vendor nid as the part of driver data and uses it.
Signed-off-by: Pradeep Tewani <pradeep.d.tewani@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5677_to_irq() has couple of redundant conditionals, one of which
compares unsigned variable to be great than or equal to zero which
is always true as compiler notices:
sound/soc/codecs/rt5677.c: In function ‘rt5677_to_irq’:
sound/soc/codecs/rt5677.c:4626:13: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Refactor the code by removing redundant conditionals.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no user of legacy platform data.
Remove separate header and hide its content inside module sources.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch corrects the mixer siwtch setting that was the mistake in the
previous commitment. And remove the redundant routing paths.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT274 is a HD-A/SOC dual mode codec. This is the initial codec driver
of SOC mode.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch modifies the default value for ASRC function. It could prevent
the pop noise and recording no sound with ASRC function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Also, make rt5514_aif_dai_ops static, as it is not used outside this
module.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the ability to configure the MFP1->MFP5 registers
as GPIOs. In addition adding ALSA controls to get and set
the GPIO state.
Per the data sheet each MFP can be configured as a GPIO
input only, output only or either an input or output.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the tlv320aic32x6 family of devices.
These devices share the same register set as the tlv320aic32x4
and this driver can be re-used.
TLV320aic32x6 data sheets are here:
tlv320aic3256 - http://www.ti.com/lit/gpn/tlv320aic3256
tlv320aic3206 - http://www.ti.com/lit/gpn/tlv320aic3206
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch uses the IRQ to copy the PCM data to userspace continuously after
the hotwording triggered from DSP.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Idealy PLL will be set in machine driver if MCLK doesn't meet the
requirement of codec. To let the codec driver be more general, we
can use a common PLL setting once sysclk/pll doesn't set properly
in machine driver.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
platform_get_irq() returns an error code, but the twl6040
driver ignores it and always returns -EINVAL. This is not correct,
and prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error.
Print and propagate the return value of platform_get_irq on failure.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds the manual offset field in the devicetree to compensate the
DC offset that will be different between the PCB layout. It only can be
measured by the real production.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The loop counter 'count' is missing an increment, so we could end up
with an infinite loop. Add in a pre-increment to count to fix this.
Detected by CoverityScan, CID#1450120 ("Logically Dead Code")
Fixes: 1a425dbf1a10 ("ASoC: rt5663: Update the calibration funciton")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch modifies the power sequence for reducing the pop sound.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch updates the calibration funciton for getting the correct DC
offset of headphone output.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the auto disable DSP function from the widget event "DAPM Pre" to
the set_bias_level() function to avoid the unexpected behavior. While the
SPI was recording using the DAI "rt5514-dsp-cpu-dai", the event "DAPM Pre"
would be manipulated even the DAPM widgets were not connected, and it also
would power off the DSP that cause the DSP buffered data lost. So the auto
disable DSP function should move to the set_bias_level() function to make
sure that it is only manipulated by the DAPM widgets are connected.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate array hdmi_codec_eld_spk_alloc_bits on the stack but
make it static. Makes the object code smaller by over 260 bytes:
Before:
text data bss dec hex filename
10882 3384 64 14330 37fa sound/soc/codecs/hdmi-codec.o
After:
text data bss dec hex filename
10557 3440 64 14061 36ed sound/soc/codecs/hdmi-codec.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current hdmi-codec driver is using hdmi_controls for "ELD" control.
But, hdmi-codec driver might be used from many HDMIs. Thus, we need
to correspond device number, otherwise we will receive below error.
xxx: control x❌x:ELD:x is already present
This patch registers ELD control in .pcm_new by using
.device = rtd->pcm->device to corresponding to PCM stream.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[Takashi: use snd_ctl_new1()/snd_ctl_add()]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch update the HW default values based on the shipping version.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For making the development easier, add quirk module option to override
the platform data setup. For example, a platform with inverted jack
detection with jd_mode=2, pass the value 0x21 (0x1 = inv_jd1_1, 0x20 =
jd_mode=2). It overrides the whole pdata fields, so pass it
carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We will set some volatile registers in jack detection function. But
those volatile registers will be clear in rt5665_calibrate function
because we set cache bypass and reset codec in rt5665_calibrate function.
This patch add a flag to make sure that rt5665_calibrate is done
before starting jack detection.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The property type of "nuvoton,crosstalk-bypass" changes to boolean.
The document is updated as well.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the arrays fs_list and ps_list on the stack but make
them static const. Makes the object code smaller:
Before:
text data bss dec hex filename
12084 4888 64 17036 428c sound/soc/codecs/ak4642.o
After:
text data bss dec hex filename
11883 5032 64 16979 4253 sound/soc/codecs/ak4642.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch is uploaded for enabling the speaker protection features
of the audio codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_sysclk to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
{ "ADC Stereo1 Filter", NULL, "PLL1", is_sys_clk_from_pll }, and
{ "ADC Stereo2 Filter", NULL, "PLL1", is_sys_clk_from_pll }, are
defined twice in the driver.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we select "IF1_ADC4" for IF1 ADC Muxes, it is actually connected
to "TxDP_ADC" widget. This patch fixes the audio route and remove the
unexisting "IF1_ADC4" widget.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add debug message for crosstalk function bypass.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The timer may still be running when rt5645_i2c_remove() gets called,
call del_timer_sync() to make sure it is stopped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPD Win requires jd_mode=3 and the inverted flag for making the jack
detection working. Unfortunately, the BIOS doesn't give a nice way to
match with DMI strings, and the only working way so far is to match
with the board vendor/name/version/date to some known patterns.
Hopefully other vendors won't do such a stupid setup, too...
Thanks to Hans de Goede for the DMI matching suggestion.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The flag will invert jd1_1 status. Which will be used if the jack
connector is normal closed.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jd_invert flag is actually used for level triggered IRQ. Rename
it to let code more readable.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Read the jd status after invert control. The benefit is we don't need
to invert the reading jd status when jd invert is needed.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make crosstalk functoin optional.
The jack detection can speed up without crosstalk detection.
Let the decision of function usage to platform design.
The patch helps the issue concern as follows:
Google issue 35574278: Chell_headphone pop back from S3
There is a concern as follows:
cras getting blocked for 2 seconds (worst-case 3 seconds)
As I understand, ChromeOS expects resume finishes in 1 seconds.
Video/Audio playing after 3 seconds of resume seems against the spec.
If we really have to make the choice I would choose pop noise instead
of waiting for 3 seconds.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the issue that mic type detection error after resume.
The microphone type detection procedure will recognize
testing signal on JKSLV pin, but before the procedure,
JKSLV already had supply voltage, that results in the failure.
Therefore, the patch turns off the power and reset the jack type
configuration before suspend. Then redo the jack detection
procedure after resume.
The patch help to fix the issue as follows:
Google issue 37973093: CTIA/OMTP jack type detection failure after resume
Reported Issue
Chrome OS Version : ChromeOS R59-9460.13.0
Type of hardware : DVT sample
What steps will reproduce the problem?
(1 Play a music
(2 Insert a headphones
(3 Close laptop lid 3 sec then open it
What is the expected output?
The music is normal in the headphones.
What do you see instead?
Singer voice in the music is not clear.
How frequently does this problem reproduce?
Always
What is the impact to the user, and is there a workaround?
If so, what is it?
Re-insert the headset or close the laptop lid and
then open it again can be repaired.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Assign default value for codec private data when property not given.
If without those default value and property, the codec will work
abnormally.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It adds ASoC driver for AUD96P22 stereo audio codec integrated on ZTE
ZX family SoCs. The driver includes the support for a number of volume
and mute controls, and power bits for various playback and recording
components.
Due to that the board for testing only supports playback, recording
support is untested.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Without CONFIG_I2C, we get a build failure:
sound/soc/codecs/es8316.c:633:1: error: data definition has no type or storage class [-Werror]
sound/soc/codecs/es8316.c:633:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
sound/soc/codecs/es8316.c:633:1: error: parameter names (without types) in function declaration [-Werror]
sound/soc/codecs/es8316.c:623:26: error: 'es8316_i2c_driver' defined but not used [-Werror=unused-variable]
This adds the required Kconfig dependency.
Fixes: b8b88b7087 ("ASoC: add es8316 codec driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The array ni_div does not need to be in global scope and is not
modified, so make it static const.
Cleans up sparse warning:
"symbol 'ni_div' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when HP detection procedure runs for certain MCLK
frequencies, when PLL is bypassed, the procedure will incorrectly
report Lineout instead of Headphones due to timing incosistencies.
To avoid this problem, the PLL is temporarily enabled (if currently
bypassed and MCLK present) to provide consistent timings for the
procedure, regardless of MCLK frequency.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ak4613 accepts all range of Sampling Rate, but it depends on
inputed master clock. This patch adds hw constraint rule for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIO ACPI mapping table is defined on platform basis. Codec driver
shouldn't have known what platform is using it.
Make codec driver more generic by moving platform code to where it
belongs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2C devices are enumerated by IDs, and not by instances.
Make it clear by using proper module device table for ACPI case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The sgtl5000 features an automatic volume control block (AVC), which
reduces loud signals and amplifies low level signals for easier
listening. This patch adds support for this AVC block to the driver.
Apart from the "AVC Switch" control which enables the block following
controls for the configuration of AVC are added:
+ AVC Threshold Volume: threshold where audio is compressed when
the measured level is above or expanded when below
+ AVC Max Gain Volume: maximum gain which can be applied when
the measured audio level is below threshold
+ AVC Hard Limiter Switch: when enabled the signal is limited to
the programmed threshold.
+ AVC Integrator Response: response time of the integrator
The AVC block is enabled and configured using the DAP_AVC_CTRL and
DAP_AVC_THRESHOLD registers.
Following 2 checkpatch.pl strict checks are ignored because the
indentation style is different for the struct snd_kcontrol_new
definition:
patch:147: CHECK: Alignment should match open parenthesis
patch:150: CHECK: Alignment should match open parenthesis
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_hw_constraint_list(), *_ratnums() and *_ratdens() receive the
const pointers. Constify the corresponding static objects for better
hardening.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_hw_constraint_list(), *_ratnums() and *_ratdens() receive the
const pointers. Constify the corresponding static objects for better
hardening.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the suspend, the IRQ function will not work in some machines. So the JD
status should be checked in the resume function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a codec driver for the Everest ES8316, based on code provided by
David Yang from Everest Semi.
I limited the functionality to items where the vendor code was clear,
and things that can be tested on the Weibu F3C (Intel Cherry Trail).
As a result the initial implementation only supports running in slave
mode at single speed (up to 48kHz sample rate) using I2S. HPD is not
supported.
Signed-off-by: David Yang <yangxiaohua@everest-semi.com>
[drake@endlessm.com: significant cleanups and simplifications,
remove dead/unclear code]
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the startup function to count DAI instead of hw_params.
This change matches the number of opened DAIs.
If this change isn't applied, you may get unexpected error due to
mismatching of count. Since the excution number of hw_params and
shutdown may be different, the mismatching happens.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct snd_pcm_hw_constraint_list ratec is not used.
Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Very fast systems may violate the minimum constraints for time the reset
line needs to remain low, or communicate with the device too soon after
releasing the reset. Fix this by adding some delays in to allow the chip
to properly reset, also factor out the reset into a function as it is
likely it will be re-used in later additions to the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The list terminator is 0xbedead but the message warning if it
wasn't found was showing that 0xbeadead was expected.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC needs to know connected DAI ID for probing.
It is not a big problem if device/driver was only for sound,
but getting DAI ID will be difficult if device includes both
Video/Sound, like HDMI.
To solve this issue, this patch adds new .get_dai_id callback
on hdmi_codec_ops
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DesignWare HDMI driver (= dw-hdmi) is supporting HDMI sound, and its
probe function was calling sound binding function multiple times as
same HDMI device different port.
Because of this behavior, commit 9731f82d60 ("ASoC: hdmi-codec: enable
multi probe for ...") was added for multi detection case.
But, this DesignWare HDMI detection/bind code was exchanged/adjusted by
commit 69497eb923 ("drm: bridge: dw-hdmi: Implement DRM bridge...").
Now, all DesignWare HDMI sound ports are detected as 1 bindng function.
Because of this, hdmi-codec multi detection support is no longer needed.
Thus, this patch removes
commit 9731f82d60 ("ASoC: hdmi-codec: enable multi probe for ..."),
and its related
commit 340327a62c ("ASoC: hdmi-codec: Fix hdmi_of_xlate_dai_name...")
commit 8480ac5679 ("ASoC: hdmi-codec: remove HDMI device unregister")
commit 0c343a35bf ("ASoC: hdmi-codec: fix spelling mistake: ...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function already defines a ret variable at the top and makes
no particular use of the shadowed definition, as such remove the
redundant definition.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The xinfo member of struct wm_coeff_ctl_ops is never used.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The shift member of struct soc_mixer_control is unsigned int.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the SRM lock check section of code the '&' bitwise operator is
used as part of checking lock status. Functionally the code works
as intended, but the conditional statement is a boolean comparison
so should really use '&&' logical operator instead. This commit
rectifies this discrepancy.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Zero is a totally valid value to specify for the bst_ipk, as such we
should append CS35L35_VALID_PDATA to ensure that it actually makes it
into the register value.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the Boost Inductor parameters based off the size of the inductor
on the HW setup
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver now supports ACPI based initialisation as well as DT
and old pdata methods. However the FW data handling still uses
DT specific calls to read firmware data (of_property*) so for
ACPI based initialisation the FW data will only be set to default
values. This patch updates the FW handling to use device_property*
calls instead so that both ACPI and DT are handled as expected.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the ACPI match ID for rt5514 codec.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/rt5665.c:4928:19: warning:
symbol 'rt5665_i2c_driver' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc 4.1.2:
sound/soc/codecs/rt5665.c: In function ‘rt5665_i2s_pin_event’:
sound/soc/codecs/rt5665.c:2610: warning: ‘mask1’ may be used uninitialized in this function
sound/soc/codecs/rt5665.c:2610: warning: ‘val2’ may be used uninitialized in this function
sound/soc/codecs/rt5665.c:2610: warning: ‘val1’ may be used uninitialized in this function
The first one is currently a false positive, as rt5665_i2s_pin_event()
is never called with snd_soc_dapm_widget.shift set to a value not
handled by the switch() statement. But that may change, so
preinitialize mask1 to fix this, like is already done for mask2.
The last two are false-positives, the compiler is just not smart enough
to notice the mask and val variables are always used together.
Fixes: 9b5d3865b3 ("ASoC: rt5665: set i2s pin share configuration")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds more width and channels support in the TDM mode.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support TDM format for NAU88L24.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A function snd_soc_update_bits() is an application of
regmap_update_bits_base(). This function takes some arguments for bitmask
and new value, thus the arguments should be a type which has width.
However bool is used to variable for the argument. This brings truncation
and results in invalid operation.
This commit fixes this bug by using unsigned int type, instead of bool.
This bug is detected by sparse:
smsm8916-wcd-analog.c:809:43: warning: odd constant _Bool cast (40 becomes 1)
smsm8916-wcd-analog.c:814:43: warning: odd constant _Bool cast (40 becomes 1)
Fixes: 585e881e5b ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the SRM lock check section of code the '&' bitwise operator is
used as part of checking lock status. Functionally the code works
as intended, but the conditional statement is a boolean comparison
so should really use '&&' logical operator instead. This commit
rectifies this discrepancy.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Thinkpad Helix 2 is a tablet PC, the audio is powered by Core M
broadwell-audio and rt286 codec. For all versions of Linux kernel,
the stereo output doesn't work properly when earphones are plugged
in, the sound was coming out from both channels even if the audio
contains only the left or right channel. Furthermore, if a music
recorded in stereo is played, the two channels cancle out each other
out, as a result, no voice but only distorted background music can be
heard, like a sound card with builtin a Karaoke sount effect.
Apparently this tablet uses a combo jack with polarity incorrectly
set by rt286 driver. This patch adds DMI information of Thinkpad Helix 2
to force_combo_jack_table[] and the issue is resolved. The microphone
input doesn't work regardless to the presence of this patch and still
needs help from other developers to investigate.
This is my first patch to LKML directly, sorry for CC-ing too many
people here.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=93841
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Mark Brown <broonie@kernel.org>
Asymmetric audio interface formats exist in ak4613 by same
register settings.
Capture Playback
24bit LEFT_J 16bit RIGHT_J
24bit LEFT_J 20bit RIGHT_J
24bit LEFT_J 24bit RIGHT_J
24bit LEFT_J 24bit LEFT_J
24bit I2S 24bit I2S
These asymmetric formats makes driver / behavior difficult.
It is not HW limitation, but SW limitation. To makes code reading
easy, this patch removes asymmetric format support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gcc-7 warns that there is a duplicate 'const' specifier in some
variables that are declared using the SOC_ENUM_SINGLE_DECL macro:
sound/soc/codecs/rt5665.c:915:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(rt5665_if1_1_01_adc_enum,
sound/soc/codecs/rt5665.c:918:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(rt5665_if1_1_23_adc_enum,
sound/soc/codecs/rt5665.c:921:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(rt5665_if1_1_45_adc_enum,
sound/soc/codecs/rt5665.c:924:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(rt5665_if1_1_67_adc_enum,
...
This removes one to fix the 68 warnings in this file
Fixes: 33ada14a26 ("ASoC: add rt5665 codec driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
gcc-7 warns that there is a duplicate 'const' specifier in some
variables that are declared using the SOC_ENUM_SINGLE_DECL macro:
sound/soc/codecs/rt5514.c:398:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(
sound/soc/codecs/rt5514.c:405:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(
This removes one to fix the warning.
Fixes: 4a6180ea73 ("ASoC: rt5514: add rt5514 codec driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
