It had changed to be suspend event for BIT6 in DEVT register from
version 2.30a and above. Thus this patch introduces one suspend
event handler to handle the suspend event.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implementations might use different IRQs for
host, gadget so use named interrupt resources
to allow device tree to specify the interrupts.
Following are the interrupt names
Peripheral Interrupt - peripheral
HOST Interrupt - host
Maintain backward compatibility for a single named
interrupt ("dwc3_usb3") for all interrupts as well as
unnamed interrupt at index 0 for all interrupts.
As platform_get_irq() variants are used, tackle
the -EPROBE_DEFER case as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It will be crash to stop gadget when the dwc3 device had been into suspend
state, thus we need to check if the dwc3 device had been into suspend state
when UDC try to stop gadget.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Because of recent changes to transfer handling on
DWC3, we will not get XferComplete unless we
completely fill up our TRB ring. This means that we
might get a Reset or Disconnect without getting a
XferComplete first.
In order to correctly release our allocated Transfer
Resource, we must issue ENDTRANSFER command whenever
dep->resource_index is valid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If there is a failure after pm_runtime_enable/get_sync()
we need to call pm_runtime_disable/put_sync().
Otherwise it will lead to an unbalanced pm_runtime_enable() on the
subsequent probe if the earlier probe bailed out due to -EPROBE_DEFER.
pm_runtime_get_sync() can fail as well so deal with that case too.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
it's clear now that when is_on=true, we must loop
until DWC3_DSTS_DEVCTRLHLT clears; while when
is_on=false we must loop until DWC3_DSTS_DEVCTRLHLT
gets set.
Instead of adding actual if() statements, we can
rely on XOR operation to evaluate to true only when
the above conditions apply. Then, we can move the
break condition back to the while() statement
together with our timeout check and the resulting
code is very compact and simpler to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of looping forever and forcing a return if
timeout reaches zero, we can just use timeout and
loop's break condition directly.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
testing shows that udelay() is unnecessary as
controller reaches Halted state almost
instantenously as can be seen by our timeout
variable never actually decrementing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We shouldn't change a host-only dwc3 to gadget-only
if driver is built as gadget-only. Fix that up here.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's know that Intel's SoCs' dwc3 integration is
peripheral-only since Intel implements its own
portmux for role-swapping. In order to prevent dwc3
from ever registering and XHCI platform_device,
let's just set dr-mode to peripheral-only on Intel
SoCs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'modify' is what the current action is called. Let's
rename it so it matches databook. While at that,
also make sure to add support 'init' action too.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now we can try to issue Update Transfer every time
gadget driver queues a new request. This will make
sure we keep controller's queue busy for as long as
possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's only set LST bit when we run out of space in
our TRB ring. For all other cases, we keep LST bit
unset which will prevent constant allocation and
deallocation of endpoint transfer resources.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of relying on empty list of queued requests,
let's rely on the fact that we have a TRB being
processed right now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will be using this information to change how we
figure out when we need LST bit. For now, just
update our counters.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to SNPS databook, we need to pass transfer
resource on update transfer command, let's do it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No more users for it.
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This should allow the core driver to drop handling of
platform data and expect the platform specific details to
always come from properties.
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Huang Rui <ray.huang@amd.com>
CC: John Youn <John.Youn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
when passing strings to trace, we don't need the
trailing newline character. Trace already appends a
newline character automatically.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Don't make any decisions regarding VBUS session based on ID
status. That is best left to the OTG core.
Pass ID and VBUS events independent of each other so that OTG
core knows exactly what to do.
This makes dual-role with extcon work with OTG irq on OMAP platforms.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
TRM [1] recommends that POWERPRESENT bit must not be
set and left at it's default value of 0.
[1] OMAP542x TRM - http://www.ti.com/lit/pdf/swpu249
Section 23.11.4.5.1 Mailbox VBUS/ID Management
"Because PIPE powerpresent has a different meaning in host and in device mode,
and because of the redundancy with the UTMI signals, the controller ORes
together the appropriate PIPE and UTMI inputs to create its internal
VBUS status. For that reason, it is recommended to leave field
USBOTGSS_UTMI_OTG_STATUS[9] POWERPRESENT at its default value (=0), and only to
fill in the USB2 VBUS status fields in the same register."
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On OMAPs, OTG events come on the same IRQ so we need to share
this IRQ with the OTG device driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We intend to share this interrupt with the OTG driver an to ensure
that irqflags match for the shared interrupt handlers we use
request_threaded_irq()
If we don't use request_treaded_irq() then forced threaded irq will
set IRQF_ONESHOT and this won't match with the OTG IRQ handler's
IRQ flags.
NOTE: OTG IRQ handler is yet to be added. This is a preparatory step.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GUCTL1 reg has some useful functions which can be
written by user. For rockchip platform, we set
GUCTL1.DEV_FORCE_20_CLK_FOR_30_CLK (bit26, applicable
for the core is programmed to operate in 2.0 device
only) to 1 in bootrom, and after start the kernel,
we want to check whether this bit can be reset to
default 0 after the core reset. Dump GUCTL1 reg from
debugfs is more convenient for us.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DWC3_USB31_REVISION_110A macro uses an invalid constant name in its
definition. This is currently not used.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Correct the use of the DWC3_DSTS_XXX_SPEED and DWC3_DCFG_XXX_SPEED
macros. The wrong set of macros were being used in a few places.
This is only a cosmetic change as the values for both sets are
identical.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
From sparse:
warning: cast truncates bits from constant value (100 becomes 0)
The DWC3_TRB_NUM constant is too big for u8. Do the calculation a
slightly different way that should still be optimized out for the case
where DWC3_TRB_NUM == 256.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the trb->enqueue == trb->dequeue, then it could be full or empty.
This could also happen at TRB index 0, so modify the check to handle
that condition. At index 0, the previous TRB is the one just before the
link TRB.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The TRBs left calculation didn't account for the link TRB taking up one
spot.
If the trb_dequeue < trb_enqueue, then the result includes the link
TRB slot so it must be adjusted.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current calculation takes dep->trb_dequeue - dep->trb_enqueue to
find the TRB space left.
If you enqueue 1, that results in:
(u8) 0 - (u8) 1 = 0xff = 255 TRBs left.
This is correct if DWC3_TRB_NUM == 256.
If DWC3_TRB_NUM is less than 256 (but still a power of 2) you need to
mod the result by DWC3_TRB_NUM.
For example the same calculation with DWC3_TRB_NUM = 8, results in:
255 % 6 = 7 TRBs left.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If trbs_left == 0, we don't have any space left in the TRB ring so don't
prepare anything.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Clears out all the TRBs in the ring to clean up any stale data that
might be in them from the previous time the endpoint was enabled.
Also removed the existing clear of the LINK trb since the entire ring is
cleard just before.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the skipping of the link TRBS built-in to the increment operation.
This simplifies the code wherever we increment the trb index and ensures
that we never end up pointing to a link trb.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sparse complains even though it looks ok. Probably it cannot detect that
the wValue, wIndex, and wLength are declared __le16 due to the macro
magic.
Redeclare them as CPU endianness and make the conversion on assignment.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleans up the sparse warning:
warning: dubious: x | !y
Since we do want a bitwise OR here, don't use a logical (true/false)
value. Probably is not a real issue but it cleans up the warning.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
u2sel and u2pel should be __le16. Doesn't fix any issue.
Found with sparse.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The wIndex passed in here is CPU endianness, but the function expects
little endian.
Found with sparse.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for endpoint commands, let's have a
single trace output for the command and its
status. This will improve trace readability
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for endpoint commands, let's use a
single return point for generic commands as
well. This aids readability.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of printing command's status with a separate
trace printout, let's print it within a single call.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of having infinite loop and always checking
timeout value as a break condition, we can just
decrement timeout inside while's condition.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
I really thought this would be useful, but as it
turns out, it creates more problems than fixes. The
amount of times we had to fix this because some
other commit shuffled things around and ended up
regressing this tiny little string manupulation...
Might as well remove it, since it has a negligible
added benefit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Improve trb tracing by showing trb flags, interrupts
trb type.
trb flags:
- h - hardware owner of descriptor
- l - last TRB
- c - chain buffers
- s - continue on short packet
interrupt flags:
- s - interrupt on short packet
- c - interrupt on complete
Capital letter means that bit is set, while
lowercase letter means bit is cleared.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will allow us to process several endpoints at a
time by making sure that we lock only shared
resources.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allow for dwc3-pci to reach D3 and enable pm_runtime
by providing dummy PM hooks. Without them, PCI
subsystem won't put device to D3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this patch implements the most basic pm_runtime
support for dwc3. Whenever USB cable is dettached,
then we will allow core to runtime_suspend.
Runtime suspending will involve completely tearing
down event buffers and require a full soft-reset of
the IP.
Note that a further optimization could be
implemented once we decide to support hibernation,
which is to allow runtime_suspend with cable
connected when bus is in U3. That's subject to a
separate patch, however.
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
when we call dwc3_gadget_giveback(), we end up
releasing our controller's lock. Another thread
could get scheduled and disable the endpoint,
subsequently setting dep->endpoint.desc to NULL.
In that case, we would end up dereferencing a NULL
pointer which would result in a Kernel Oops. Let's
avoid the problem by simply returning early if we
have a NULL descriptor.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit f3af36511e ("usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers") ended up
regressing Isochronous endpoints by clearing
DWC3_EP_BUSY flag too early, which resulted in
choppy audio playback over USB.
Fix that by partially reverting original commit and
making sure that we check for isochronous endpoints.
Fixes: f3af36511e ("usb: dwc3: gadget: always enable IOC
on bulk/interrupt transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As a micro-power optimization, let's only resume the
USB2 PHY if we're working on <=HIGHSPEED. If we're
gonna work on SUPERSPEED or SUPERSPEED+, there's no
point in resuming the USB2 PHY.
Fixes: 2b0f11df84 ("usb: dwc3: gadget: clear SUSPHY bit before ep cmds")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
by holding gadget's IRQ number in dwc->irq_gadget,
it'll be simpler to free_irq() and disable the IRQ
in case an IRQ fires while we are runtime suspended.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
now that we have re-factored dwc3_core_init() and
dwc3_core_exit() we can use them for suspend/resume
operations.
This will help us avoid some common mistakes when
patching code when we have duplicated pieces of code
doing the same thing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The idea of this patch is for dwc3_core_init() to
abstract all the details about how to initialize
dwc3 and dwc3_core_exit() to do the same for
teardown.
With this, we can simplify suspend/resume operations
by a large margin and always know that we're going
to start dwc3 from a known starting point.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this patch is in preparation for some further
re-factoring in dwc3 initialization. No functional
changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By adding a pointer to endpoint registers' base
address, we can avoid using our controller-wide
struct dwc3 pointer for everything. At some point
this will allow us to have per-endpoint locks which
will, in turn, let us queue requests to separate
endpoints in parallel.
Because of this change our debugfs interface and io
accessors need to be changed accordingly.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In all call sites of dwc3_send_gadget_ep_cmd() we
already had a valid dep pointer, so instead of
passing dwc and dep->number, which would be used to
fetch the same pointer we already had, just pass dep
directly.
In other words, we're changing:
struct dwc3_ep *dep = dwc[dep->number];
to just passing struct dwc3_ep *dep as argument.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of using burst size to configure NUMP, we
should be using RxFIFO Size instead. DWC3 is smart
enough to know that it shouldn't burst in case burst
size is 0.
Reported-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To aid code readability, we're gonna split
__dwc3_gadget_kick_transfer() into its constituent
parts: scatter gather and linear buffers.
That way, it's easier to follow the code and focus
debug effort when one or the other fails.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of returning -EINVAL when someone calls
__dwc3_gadget_wakeup() in speeds > highspeed, let's
return 0. There are no problems for the driver for
calling it in superspeed as we cleanly just return.
This avoids an annoying WARN_ONCE() always
triggering during superspeed enumeration with LPM
enabled.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we send an endpoint command, we want that to
complete as soon as possible, so let's remove the
unnecessary udelay(1) call.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
sg_is_last() and list_is_last() will encode the
required information for the driver to make
decisions WRT CHN and LST bits.
While at that, also replace '1' with 'true' for
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
as it turns out, we don't need the extra 'start_new'
argument as that can be inferred from DWC3_EP_BUSY
flag.
Because of that, we can simplify
__dwc3_gadget_kick_transfer() by quite a bit, even
allowing us to prepare more TRBs unconditionally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we're updating transfers, we can also prepare as
many TRBs as we can fit in the ring. Let's start
doing that.
This patch 'solves' a limitation of how many TRBs we
can prepare when we're getting close the end of the
ring. Instead driver to prepare only up to end of
the ring, we check if we have space to wrap around
the ring properly.
Note that this only happens when our enqueue and
dequeue pointers are equal (which is the case for
bulk endpoints after an XferComplete event).
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of trying hard to stay connected to the
host, it's best (and far easier) to disconnect from
the host already.
Anything relying on KEEP_CONNECT will just have that
ignored, but we don't have proper hibernation
implementation yet, so there are no regressions.
In any case, hibernation is only useful for runtime
PM, not system sleep.
While at that, also remove dwc3.dcfg which has been
rendered unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be re-using it for suspend/resume, so
instead of duplicating code, let's just re-factor
the functions so they can be re-used.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As of core revision 2.60a the recommended programming model is to set
the ClearPendIN bit when issuing a Clear Stall EP command for IN
endpoints. This is to prevent an issue where some (non-compliant) hosts
may not send ACK TPs for pending IN transfers due to a mishandled error
condition. Synopsys STAR 9000614252.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set USB3_FORCE_VBUSVALID when configured for USB_DR_MODE_PERIPHERAL
mode, as it is required to have a working setup.
This worked on the internal driver by relying on the reset
value of the syscfg register as the bits aren't explicity cleared
and set like the upstream driver.
Also add a comment about what setting this bit means.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3-exynos has two problems during init if the regulators are slow
to come up (for instance if the I2C bus driver is not on the initramfs)
and return probe deferral. First, every time this happens, the driver
leaks the USB phys created; they need to be deallocated on error.
Second, since the phy devices are created before the regulators fail,
this means that there's a new device to re-trigger deferred probing,
which causes it to essentially go into a busy loop of re-probing the
device until the regulators come up.
Move the phy creation to after the regulators have succeeded, and also
fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs
which doesn't contain the I2C driver), this reduces the number of probe
attempts (for each of the two controllers) from more than 2000 to eight.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Fixes: d720f057fd ("usb: dwc3: exynos: add nop transceiver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the original DWC3_DCFG_NUMP() was always zero. It looks like the
intent was to shift first and then do the mask.
Fixes: 2a58f9c12b ('usb: dwc3: gadget: disable automatic calculation of ACK TP NUMP')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7szP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.7 merge window
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
Now that we calculate DCFG.NUMP, we can disable
dwc3's automatic calculation so we maximize our
chances of very high throughtput through the use of
bursts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NumP field of DCFG register is used on NumP field of
ACK TP header and it tells the host how many packets
an endpoint can receive before waiting for
synchronization.
Documentation says it should be set to anything
<=bMaxBurst. Interestingly, however, this setting is
not per-endpoint how it should be (different
endpoints could have different burst sizes), but
things seem to work okay right now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
if Start Transfer command fails, let's try a little
harder to figure out why the command failed and give
slightly better return codes. This will be usefulf
or isochronous endpoints, at least, which could
decide to retry a given request.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For convenience, passing the dwc3 platform device as a
parameter to dwc3_pci_quirks() function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Setting the ACPI companion before calling dwc3_pci_quirks.
The ACPI companion will be set unconditionally as the
primary fwnode, overriding any previously set primary
fwnode. This will make sure that any build-in properties
added to the platform device will be added as the secondary
fwnode in cases where also ACPI companion exists.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case host sends us an unsupported test mode, we
*must* stall this request. This will tell the host
that the selector is invalid and we won't put the
controller in unsupported test modes which could
have undetermined side-effects.
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a bunch of information in the debug register
set from dwc3 which is useful in some debugging
scenarios. Let's dump them out in endpoint-specific
directories and designated files.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This helper will be used later to convert trb type
into a human-readable string for debugfs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this helper will be used, initially, to dump space
of different queues and fifos in dwc3 to
debugfs. Later, it'll be used to issue remote wakeup
when we want to start a transfer and there's
something in a TX FIFO.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Debugfs init failure is not so important. We can continue our job on
this failure. Also no break need for debugfs_create_file call failure.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[felipe.balbi@linux.intel.com :
- remove out-of-memory message, we get that from OOM.
- switch dev_err() to dev_dbg() ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dma_status bit flag is set but never really used
so get rid of it.
Reported-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It makes no sense to interrupt in the middle of
chained transfer. This patch just makes sure we
don't do that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of limiting link TRB only to Isoc endpoints,
let's use it for all endpoint types, this way we are
more likely to transfer more data before a
XferComplete event.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By moving our % DWC3_NUM_TRB operation to the
increment helpers, the rest of the driver can be
simplified.
It's also a good practice to make sure we will have
a single place dealing with details about how to
increment our enqueue and dequeue pointers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add three little helpers which will aid in making
the code slightly easier to read. One helper
increments enqueue pointer, another increments
dequeue pointer and the last one tests if we're
dealing with the last TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a bitwise and, let's rely on the %
operator since that's a lot more clear. Also, GCC
will optimize % 256 to nothing anyway.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We *know* that we have 1 PAGE (4096 bytes) for our
TRB poll. We also know the size of each TRB and know
that we can fit 256 of them in one PAGE. By using a
u8 type we can make sure that:
enqueue++ % 256;
gets optimized to an increment only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it clear that we're dealing with a queue
of TRBs. No functional changes. While at that, also
rename start_slot to first_trb_index for similar
reasons.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DWC3 OMAP driver supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-omap.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook says we should move link to U0
before issuing a Start Transfer command. We could
require the gadget driver to call
usb_gadget_wakeup() however I feel that changing all
gadget drivers to keep track of Link State and
conditionally call usb_gadget_wakeup() would be far
too much work. For now we will handle this at the
UDC level, but at some point composite.c should be
one handling this.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.
This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.
Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we don't plan on using multiple event buffers, but
if we find a good use case for it, this little trick
will help us avoid a loop in hardirq handler looping
for each and every event buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget controller might not be always active during system
suspend/resume as gadget driver might not have yet been loaded or
might have been unloaded prior to system suspend.
Check if we're active and only then perform
necessary actions during suspend/resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc->regset is allocated on dwc3_debugfs_init, and should
be released on init failure or dwc3_debugfs_exit. Btw,
The line "dwc->root = NULL" is unnecessary, so remove it.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[ felipe.balbi@linux.intel.com : add another err label for the new
error condition ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we need to power off the PHY during suspend and
power it back on during resume.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: fix call to usb_phy_set_suspend() in dwc3_suspend()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even if pm_runtime_get*() fails, we *MUST* call
pm_runtime_put_sync() before disabling PM.
While at it, remove superfluous dwc3_omap_disable_irqs()
in error path.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: patch description updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be using a single event buffer and that
renders ev_buffs array unnecessary. Let's remove it
in favor of a single pointer to a single event
buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We never, ever route any of the other event buffers
so we might as well drop support for them.
Until someone has a real, proper benefit for
multiple event buffers, we will rely on a single
one. This also helps reduce memory footprint of
dwc3.ko which won't allocate memory for the extra
event buffers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
request_list and req_queued were, well, weird naming
choices.
Let's give those better names and call them,
respectively, pending_list and started_list. These
new names better reflect what these lists are
supposed to do.
While at that also rename req->queued to req->started.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
previously we were using a maximum of 32 TRBs per
endpoint. With each TRB being 16 bytes long, we were
using 512 bytes of memory for each endpoint.
However, SLAB/SLUB will always allocate PAGE_SIZE
chunks. In order to better utilize the memory we
allocate and to allow deeper queues for gadgets
which would benefit from it (g_ether comes to mind),
let's increase the maximum to 256 TRBs which rounds
up to 4096 bytes for each endpoint.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit of TRB Control is useful for protocols such
CDC EEM/ECM/NCM where we're transferring in blocks
of MTU-sized requests (usually MTU is 1500 bytes).
We know we will always have a short packet after two
(for HS) wMaxPacketSize packets and, usually, we
will have a long(-ish) queue of requests (for our
g_ether gadget, we have at least 10
requests).
Instead of always stopping the queue processing to
interrupt, giveback and restart, let's tell dwc3 to
interrupt but continue processing following request
if we have anything already pending in the queue.
This gave me a considerable improvement of 40% on my
test setup.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16f8 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Keystone 2 supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-keystone.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Cc: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
BXT-M is a Intel Broxton SoC based platform with unique PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We were exitting the function before actually
renaming anything. While at that, also always leave
control endpoint un-renamed.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's a requirement that we release controller's lock
while calling gadget API function pointers. This
patch just fixes that long standing bug.
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook, we shouldn't be
relying on GCTL.CORESOFTRESET bit as that's only for
debugging purposes. Instead, let's use DCTL.CSFTRST
if we're OTG or PERIPHERAL mode.
Host side block will be reset by XHCI driver if
necessary. Note that this reduces amount of time
spent on dwc3_probe() by a long margin.
We're still gonna wait for reset to finish for a
long time (default to 1ms max), but tests show that
the reset polling loop executed at most 19 times
(modprobe dwc3 && modprobe -r dwc3 executed 1000
times in a row).
Suggested-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
new device support in terms of LoC, but there has been some cleanup
in the core as well as the usual minor clk additions to various
drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a minor
refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bZFY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
Check that dwc->maximum_speed is set to a valid value. Also add an error
when we use it later if we encounter an invalid value.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable SuperSpeedPlus by programming the DCFG.speed and after
enumerating, set gadget->speed appropriately.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the maximum_speed is not set, set it to a known value, either
SuperSpeed or SuperSpeedPlus based on the type of controller we are
using. If we are on DWC_usb31 controller, check the PHY interface to see
if it is capable of SuperSpeedPlus.
Also this check is moved after dwc3_core_init() so that we can check
dwc->revision.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update various places where the speed is checked so that it takes into
account SuperSpeedPlus properly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update various registers fields definitions for the DWC_usb31 controller
for SuperSpeedPlus support.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add a convenience function to check if the controller is DWC_usb31.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The check for < 0 is impossible now that
of_clk_get_parent_count() returns an unsigned int. Simplify the
code and update the types.
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch is needed in order to pass one test case
defined in the OTG Automated Compliance Test specification.
Specification location:
http://www.usb.org/developers/onthego/otgeh_compliance_plan_1_2.pdf
This test case uses PET Tool, and PET Tool is one USB hardware
equipment provided by MQP Electronics.
Test case id is 6.8.3 B-UUT Bypass Capacitance.
We must set this otg flag in order to be able to return OTG
descriptor during enumeration, otherwise this test case with
failed with below error: "Get OTG descriptor request stalled".
Signed-off-by: Jianqiang Tang <jianqiang.tang@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
if we have a !PM kernel build, our runtime
suspend/resume callbacks will be left defined but
unused. Add a ifdef CONFIG_PM guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the request->length is zero, a ZLP should already be sent due to that
and another ZLP is not needed to terminate the transfer.
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct usb_request have 3 flags which might be
important to know about during debug. This patch
shows each of the 3 flags as a single letter:
z -> for zero
s -> short not okay
i -> interrupt
A capital letter means the feature is enabled
while a lower case letter means it is disabled;
Thus 'zsI' indicates that a ZLP is not needed,
that we can accept a short packet and interrupt
for this request should be enabled.
Signed-off-by: Felipe Balbi <balbi@ti.com>
So far, dwc3 has always missed request->zero
handling for every endpoint. Let's implement
that so we can handle cases where transfer must
be finished with a ZLP.
Note that dwc3 is a little special. Even though
we're dealing with a ZLP, we still need a buffer
of wMaxPacketSize bytes; to hide that detail from
every gadget driver, we have a preallocated buffer
of 1024 bytes (biggest bulk size) to use (and
share) among all endpoints.
Reported-by: Ravi B <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that we have a generic dwc3-of-simple.c, we can
use that instead of maintaining dwc3-qcom.c which is
extremely similar.
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For simple platforms which merely enable some clocks
and populate its children, we can use this generic
glue layer to avoid boilerplate code duplication.
For now this supports Qcom and Xilinx, but if we
find a way to add generic handling of regulators and
optional PHYs, we can absorb exynos as well.
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It just ocurred to me that dwc3 already gives a
really hint of when a setup packet is pending and
that's the SETUP_PENDING TRB Status for EP0 IRQs.
Fix setup_packet_pending initialization based on
that. While at that, also make sure the comment in
gadget.c matches what code is doing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In dwc3_cleanup_done_reqs() we expect that all
iterations of our while (1) loop will find a valid
struct dwc3_request *. In case we don't, we're
dumping a WARN_ON_ONCE() splat so that people report
the failure.
This patch is a simple cleanup converting:
if (!req) {
WARN_ON_ONCE(1);
return 1;
}
to:
if (WARN_ON_ONCE(!req))
return 1;
which is a little easier to read.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
By moving our sanity checks our internal function
__dwc3_gadget_ep_queue() we can simplify the
externally visible API while also making sure that
callers of __dwc3_gadget_ep_queue() also make use of
the same checks.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Because interrupt endpoints usually transmit such
small amounts of data, it seems pointless to prestart
transfers and try to get speed improvements. This
patch also sorts out a problem with CDC ECM function
where its notification endpoint gets stuck in busy
state and we continuously issue Update Transfer
commands.
Fixes: 8a1a9c9e45 ("usb: dwc3: gadget: start transfer on XFER_COMPLETE")
Signed-off-by: Felipe Balbi <balbi@ti.com>
In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.
Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.
At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.
[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 8f2c9544ab.
As it breaks g_ether on my Baytrail FFRD8 device. Everything starts out
fine, but after a bit of data has been transferred it just stops
flowing.
Note that I do get a bunch of these "NOHZ: local_softirq_pending 08"
when booting the machine, but I'm not really sure if they're related
to this problem.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 70f3a9caa1.
That commit was causing a lockdep splat with g_ether and that
was interfering with proper functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Certain Synopsys prototyping PHY boards are not able to meet timings
constraints for LPM. This allows the PHY to meet those timings by
leaving the PHY clock running during suspend.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add platform data and set usb3_lpm_capable and has_lpm_erratum.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the alignment of the PCI device definitions. Also change the hex
digit capitalization of one constant to make it consistent with the
rest of the file and driver.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch allows the dwc3 driver to run on the new Synopsys USB 3.1
IP core, albeit in USB 3.0 mode only.
The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register
interface and programming model as the existing USB 3.0 controller IP
(DWC_usb3). However the GSNPSID and version numbers are different.
Add checking for the new ID to pass driver probe.
Also, since the DWC_usb31 version number is lower in value than the
full GSNPSID of the DWC_usb3 IP, we set the high bit to identify
DWC_usb31 and to ensure the values are higher.
Finally, add a documentation note about the revision numbering scheme.
Any future revision checks (for STARS, workarounds, and new features)
should take into consideration how it applies to both the 3.1/3.0 IP.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds the PCI product ID for the Synopsys USB 3.1 IP core
(DWC_usb31) on a HAPS-based PCI development platform.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This ID is for the Synopsys DWC_usb3 core with AXI interface on PCIe
HAPS platform. This core has the debug registers mapped at a separate
BAR in order to support enhanced hibernation.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We *know* our threads executes with our IRQs
disabled. We really don't need to use the _irqsave()
variant of spin_lock().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of limiting __dwc3_gadget_kick_transfer() to
Xfer Complete, we can try to issue Update Transfer
command from Xfer In Progress too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we get a Xfer Not Ready event with reason
"Transfer Active" it means endpoint is still
transferring data and we can use that to issue
update transfer for this particular endpoint
in case we have pending requests in our queue.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if by the time we get to XFER_COMPLETE we have
pending requests to be processed, instead of waiting
for a following XFER_NOT_READY, let's start the request
right away and, maybe, save the time of a few NAKs
due to lack of started transfers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sharing the ACPI companion with dwc3 core so it has access
to the properties defined for DWC3 in ACPI tables.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional affect on existing platforms, but the driver
is now ready to extract the properties also from ACPI tables
as well as from DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_usb_get_dr_mode will be converted into more generic
usb_get_dr_mode function that will take struct device
instead of struct device_node as its parameter.
To make the conversion possible later, waiting for the
platform device for dwc3 to be populated before calling
of_usb_get_dr_mode.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for USB DRVVBUS pinctrl state change during
suspend/resume. This helps is conserving power during
system sleep.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We shouldn't return -EBUSY, that's used only internally
when the core still has transfers in flight on a given
endpoint.
Also, combine the error reporting so that we don't have
to duplicate it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of clearing DWC3_PENDING_REQUEST when
we start transfer, let's do it when the request
is actually queued, that way we know for sure
that we're clearing in the right time.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In an attempt to make dwc3 slightly faster, let's
start usb_requests as soon as they come as that will
let us avoid a XFER_NOT_READY event and save a little
bit of time.
Signed-off-by: Felipe Balbi <balbi@ti.com>
by moving trace_dwc3_ep_queue() from dwc3_gadget_ep_queue()
to __dwc3_gadget_ep_queue() after usb_request is properly
initialized, makes for a better output always showing a
request with 0 actual and -115 (-EINPROGRESS) status.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using spin_lock() in hard irq handler is pointless
and causes a BUG() in RT (real-time) configuration
so get rid of it.
The reason it's pointless is because the driver is
basically accessing register which is, anyways,
atomic.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we enable IRQs before requesting our
extcon device, we might fall into a situation
where and IRQ fires before we're ready to
handle it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use chained TRB mechanism to handle non maxpacket aligned transfers
greater than bounce buffer size. With this the first TRB will be programmed
to receive 'ALIGN(ur->length - maxp, maxp)' data and the second TRB
will be programmed to receive the remaining data using bounce buffer.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add chained TRB support to ep0. Now TRB's can be chained just by
invoking _dwc3_ep0_start_trans_ with 'chain' parameter set to true.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Added a new parameter in _dwc3_ep0_start_trans_ to
indicate whether the TRB is a chained TRB or last TRB. This is in
preparation for adding chained TRB support for ep0.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. This is in preparation for handling non maxpacket
aligned transfers greater than bounce buffer size. This is basically to
avoid code duplication when using chained TRB transfers to handle
non maxpacket aligned transfers greater than bounce buffer size.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Used _roundup_ macro to calculate the transfer
size aligned to maxpacket in dwc3_ep0_complete_data. It also makes it
similar to how transfer size is calculated in __dwc3_ep0_do_control_data.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 uses bounce buffer to handle non max packet aligned OUT transfers and
the size of bounce buffer is 512 bytes. However if the host initiates OUT
transfers of size more than 512 bytes (and non max packet aligned), the
driver throws a WARN dump but still programs the TRB to receive more than
512 bytes. This will cause bounce buffer to overflow and corrupt the
adjacent memory locations which can be fatal.
Fix it by programming the TRB to receive a maximum of DWC3_EP0_BOUNCE_SIZE
(512) bytes.
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We have a "Enabling %s" trace when enabling an endpoint
but that message felt lonely without a matching
"Disabling %s". Add it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a SoC supports both PHY interfaces but
doesn't define HSPHY in DT/pdata, we will get
an unnecessary dev_warn() which can mislead users
into thinking that they're missing something.
Instead, let's just silently rely on a correct
default. If the HW default is wrong, then HSPHY
is required and USB won't work, this will be
motivation enough for engineers to patch their
way into a working setup.
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this additional parameter and the _optional variant to simplify the
driver and improve error handling. Also expand the comment to explain
why it's not sensible to switch to devm_gpiod_get and why the gpiod_put
is also necessary.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).
Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that we have no users of dev_dbg() in dwc3,
we can safely remove CONFIG_USB_DWC3_DEBUG.
If dev_dbg() is ever strictly necessary - and I
don't see why it would, considering we want to
rely on tracepoints for debug - we will depend
on DYNAMIC_PRINTK to enable such messages.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the mode of operation is exposed through debugfs
at all times. Because of that, we're removing
the unnecessary messages.
Signed-off-by: Felipe Balbi <balbi@ti.com>
those two messages are informing that the clock
doesn't exist; that, however, is a valid situation
and driver continues just fine by ignoring the error.
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
that message is informing that the clock is missing.
However, that's a valid condition for some setups; driver
even ignores the error and continues just fine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This fixes an issue introduced in commit b23c843992 (usb: dwc3:
gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would
only use DEPSTARTCFG once per SetConfig.
The trick is that we should use one DEPSTARTCFG per SetConfig *OR*
SetInterface. SetInterface was completely missed from the original
patch.
This problem became aparent after commit 76e838c9f7 (usb: dwc3:
gadget: return error if command sent to DEPCMD register fails)
added checking of the return status of device endpoint commands.
'Set Endpoint Transfer Resource' command was caught failing
occasionally. This is because the Transfer Resource
Index was not getting reset during a SET_INTERFACE request.
Finally, to fix the issue, was we have to do is make sure that
our start_config_issued flag gets reset whenever we receive a
SetInterface request.
To verify the problem (and its fix), all we have to do is run
test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'.
Tested-by: Huang Rui <ray.huang@amd.com>
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Fixes: b23c843992 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 3e10a2ce98 ("usb: dwc3: add hsphy_interface
property") introduced a possible NULL pointer
dereference because dwc->hsphy_interface can be
NULL.
In order to fix it, all we have to do is guard
strncmp() against a NULL argument.
Fixes: 3e10a2ce98 ("usb: dwc3: add hsphy_interface property")
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB_DWC3_ULPI Kconfig entry uses a UTF-8 non-breaking space (0xca20)
instead of a regular ASCII space (0x20). Commit 2e0d737fc7 ("kconfig:
don't silently ignore unhandled characters") exposes this by warning
about unhandled characters.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jqzf
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of non-Isochronous transfers, we don't
want to clear DWC3_EP_BUSY flag until XferComplete
event. That's because XferInProgress was only enabled
so we can recycle TRBs and usb_requests quicker, but
there are still other pending requests being transferred.
In order to make sure we don't allow for another StartTransfer
command while the HW is still processing other transfers,
we must keep DWC3_EP_BUSY flag set and this what this patch
does.
Fixes: f3af36511e (usb: dwc3: gadget: always enable IOC on
bulk/interrupt transfers)
Cc: <stable@vger.kernel.org> # v3.15+
Reported-by: sundeep subbaraya <sundeep.lkml@gmail.com>
Tested-by: sundeep subbaraya <sundeep.lkml@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to return error to caller if command is not sent to
controller succesfully.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Fixes: 72246da40f (usb: Introduce DesignWare USB3 DRD Driver)
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to return error to caller if command is not sent to
controller succesfully.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Fixes: b09bb64239 (usb: dwc3: gadget: implement Global Command support)
Cc: <stable@vger.kernel.org> #v3.5+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Registers DWC3's ULPI interface with the ULPI bus when it's
available.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On some BYT platforms the USB2 PHY needs to be put into
operational mode by the controller driver with GPIOs
controlling the PHYs reset and cs signals.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Platforms that have configured DWC_USB3_HSPHY_INTERFACE with
value 3, i.e. UTMI+ and ULPI, need to inform the driver of
the actual HSPHY interface type with the property. "utmi" if
the interface is UTMI+ or "ulpi" if the interface is ULPI.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This allows dwc3_phy_setup() to be more useful later. There
is nothing preventing the PHY configuration registers from
being programmed early. They do not loose their context in
soft reset.
There are however other PHY related operations that should
be executed before the driver request handles to the PHYs,
such as registering DWC3's ULPI interface, which can now be
done in dwc3_phy_setup().
Also, if there ever was need for the two 100ms delays in
dwc3_phy_setup() there isn't anymore. The PHYs are now reset
after the PHY interfaces are setup.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So it can be called from other places later.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So they are available when ULPI interface support is added.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to store it before phys are handled, so we can later
use it in ULPI interface support code.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make selection between ULPI and UTMI+ interfaces possible by
providing definition for the bit in Global USB2 PHY
Configuration Register that controls it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Definitions for Global USB2 PHY Vendor Control Register
bits. We will need them to access ULPI PHY registers later.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The macros related to register UTMI_OTG_CTRL and UTMI_OTG_STATUS are
swapped. Correct them for readability.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes "Enable USB3 LPM Capability" option from Kconfig
and adds snps,usb3_lpm_capable devicetree property instead of it.
USB3 LPM (Link Power Management) capability is hardware property, and
it's platform dependent, so if our hardware supports this feature, we
want rather to configure it in devicetree than having it as Kconfig option.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed FIXME from usb/dwc3/dwc3-pci.c by moving definition of
PCI_VENDOR_ID_SYNOPSYS shared with usb/dwc2 to linux/pci_ids.h.
Signed-off-by: Joseph Kogut <joseph.kogut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that we're using XFERINPROGRESS for all endpoint
types (except Control), we will *always* be completing
one TRB at a time, so it's safe to remove the loop
from dwc3_cleanup_done_reqs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes a bug where removing dwc3-omap.ko
would not trigger removal of dwc3.ko.
of_platform_depopulate() already bakes an easy to
use API for removing all our children which were
populated during probe(); Let's use that one instead
of cooking our own solution.
Note that this is kind of a revert of commit c5a1fbc
(usb: dwc3: dwc3-omap: Fix the crash on module removal)
although we can't simply revert that because a direct
call to platform_device_unregister would also be flakey.
Signed-off-by: Felipe Balbi <balbi@ti.com>
That trick is only needed if we end up with an error, so
there's no point in messing that outside of an error path.
In fact doing so causes problems when removing dwc3.ko,
problems which commit c5a1fbc (usb: dwc3: dwc3-omap: Fix
the crash on module removal) mistakenly tried to fix.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the wrapper the IRQ disable should be done by writing 1's to the
IRQ*_CLR register. Existing code is broken because it instead writes
zeros to IRQ*_SET register.
Fix this by adding functions dwc3_omap_write_irqmisc_clr() and
dwc3_omap_write_irq0_clr() which do the right thing.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 8e74475b0e (usb: dwc3: gadget: use udc-core's
reset notifier) added support for the new UDC core's
reset notifier to dwc3 but while at it, it removed
a spin_lock() from dwc3_reset_gadget() which might
cause an unbalanced spin_unlock() further down the line
Fixes: 8e74475b0e (usb: dwc3: gadget: use udc-core's reset notifier)
Cc: <stable@vger.kernel.org> # v3.19
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sometimes we want to just print a formatted
string without passing any extra data. The
following will be used for removing reliance
on dev_vdbg() from dwc3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if an unknown IRQ event is triggered, that means
the HW is really misbehaving. Instead of printing
a debug message, let's WARN() so users report
when that happens.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removing a few items that are not needed anymore and
adding separate function for quirks.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is nothing specific being done in the suspend and
resume callbacks that is not already taken care of in PCI
driver core, so dropping the functions.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
None of the PCI platforms need the NOP transceivers, and
since we can now live without the PHYs, removing
registration of the platform devices for them.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 gadget sets up a pool of 32 TRBs for each EP during initialization. This
means, the max TRBs that can be submitted for an EP is fixed to 32. Since the
request queue for an EP is a linked list, any number of requests can be queued
to it by the gadget layer. However, the dwc3 driver must not submit TRBs more
than the pool it has created for. This limit wasn't respected when SG was used
resulting in submitting more than the max TRBs, eventually leading to
non-transfer of the TRBs submitted over the max limit.
Root cause:
When SG is used, there are two loops iterating to prepare TRBs:
- Outer loop over the request_list
- Inner loop over the SG list
The code was missing break to get out of the outer loop.
Fixes: eeb720fb21 (usb: dwc3: gadget: add support for SG lists)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When scatter gather (SG) is used, multiple TRBs are prepared from one DWC3
request (dwc3_request). So while preparing TRBs, the 'last' flag should be set
only when it is the last TRB being prepared from the last dwc3_request entry.
The current implementation uses list_is_last to check if the dwc3_request is the
last entry from the request_list. However, list_is_last returns false for the
last entry too. This is because, while preparing the first TRB from a request,
the function dwc3_prepare_one_trb modifies the request's next and prev pointers
while moving the URB to req_queued. Hence, list_is_last always returns false no
matter what.
The correct way is not to access the modified pointers of dwc3_request but to
use list_empty macro instead.
Fixes: e5ba5ec833 (usb: dwc3: gadget: fix scatter gather implementation)
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_init_hw_endpoints calls dwc3_alloc_trb_pool only if epnum is not
equal to 0 or 1. Hence, rechecking it in the called function is redundant.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oo3u
-----END PGP SIGNATURE-----
Merge tag 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
Copy-paste error from the previous block of error handling code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
@@
if (IS_ERR(e)) {
...
(
ret = PTR_ERR(e);
|
* ret = PTR_ERR(e1);
)
...
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On some platforms a PHY may need to be handled also in the
host controller driver. Exynos5420 SoC requires some "PHY
tuning" based on the USB speed. This patch delivers dwc3's
PHYs to the xhci platform device when it's created.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
DWC3 controller on Exynos7 SoC has separate control for
AXI UpScaler which connects DWC3 DRD controller to AXI bus.
Get the gate clock for the same to control it across power
cycles.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 controller on Exynos SoC series have separate control for
suspend clock which replaces pipe3_rx_pclk as clock source to
a small part of DWC3 core that operates when SS PHY is in its
lowest power state (P3) in states SS.disabled and U3.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's no need to keep one local variable for clock, and
then assign the same to 'clk' member of dwc3_exynos.
Just cleaning it up.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was another instance where we were
holding pointers which could be long gone.
Fix that by caching only values pointed to
by such pointer.
Because no crash has been observed, this patch
will be sent on v3.19 merge window, instead of
-rc.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 6856d30 (usb: dwc3: ep0: return early
on NULL requests) tried to fix a minor corner
case where we could dereference a NULL pointer
but it also ended up introducing some dead code.
Unfortunately, that dead code, if reached, could
end up starving the endpoint request list because
a request would never be given back when it should.
Fix this by moving the check for empty request list
before its first use.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
as it turns out, at least AM437x silicon (non-FPGA)
needs to enable PHY suspend quirk. So let's allow
for PHY suspend quirk to be used with non-FPGA
builds too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following checkpatch warning.
WARNING: break is not useful after a goto or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 Exynos Specific Glue layer can be used only for Exynos SoCs.
In addition, non-DT for EXYNOS SoCs is not supported from v3.11;
thus, there is no need to support non-DT for DWC3 Exynos Specific
Glue layer.
The 'linux/platform_data/dwc3-exynos.h' file has been used for
non-DT support. Thus, the 'dwc3-exynos.h' file is removed, because
it is not used anymore.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HIRD threshold should be configurable by different platforms.
From DesignWare databook:
When HIRD_Threshold[4] is set to 1b1 and HIRD value is greater than or
equal to the value in HIRD_Threshold[3:0], dwc3 asserts output signals
utmi_l1_suspend_n to put PHY into Deep Low-Power mode in L1.
When HIRD_Threshold[4] is set to 1b0 or the HIRD value is less than
HIRD_Threshold[3:0], dwc3 asserts output signals utmi_sleep_n on L1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for AMD Nolan (NL) FPGA and SoC platform.
Cc: Jason Chang <jason.chang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb2 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb3 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds Tx de-emphasis quirk, and the Tx de-emphasis value is
configurable according to PIPE3 specification.
Value Description
0 -6dB de-emphasis
1 -3.5dB de-emphasis
2 No de-emphasis
3 Reserved
It can be configured on DT or platform data.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is recommended to set USB3 and USB2 SUSPHY bits to '1' after the core
initialization is completed above the dwc3 revision 1.94a.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds RX_DETECT to Polling.LFPS control quirk, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds LFPS filter quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay PHY power change from P0 to P1/P2/P3 when link state
changing from U0 to U1/U2/U3 respectively, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.
This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.
[ balbi@ti.com : added devicetree documentation, spelled threshold
completely, made sure threshold is only applied to
proper core revisions. ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch initializes platform data at pci glue layer, and SoCs x86-based
platform vendor is able to define their flags in platform data at bus glue
layer. Then do some independent behaviors at dwc3 core level.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.
Below thread discussion proposes to find a method to distinguish between
simulation board and soc.
http://marc.info/?l=linux-usb&m=141194772206369&w=2
In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It enables hibernation if the function is set in coreConsultant.
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadget/function drivers might want to do
improper request recycling by allocating a single
request from one particular endpoint and queueing
it to another completely unrelated endpoint.
One such case was found with f_loopback.c.
To prevent such cases from happening again, let's
WARN() so we get a loud enough failure and persuade
users to report errors.
Signed-off-by: Felipe Balbi <balbi@ti.com>
whenever we get a Disconnect Interrupt, we should
make sure to update out udc state to NOT_ATTACHED,
otherwise sysfs will show wrong values.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using ->prepare()/->complete() to mask/unmask
IRQs is wrong at least for dwc3. We need to
make sure that by the end of ->resume(), IRQs
are working and ready to fire because a child
device may need working IRQs for its own ->resume()
method.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enabling the core interrupts in complete is too late for
XHCI, and stops it from proper operation. The root of the
problem is due to a disagreement between dwc3-omap and XHCI
about when IRQs should be enabled.
As it turns out, ->resume's documentation states that:
"... generally the driver is expected to start working
again, responding to hardware events and software requests
(the device itself may be left in a low-power state, waiting
for a runtime resume to occur) ..."
From that we infer that IRQs must be unmasked by the end of
->resume().
Due to that, we will remove ->prepare() and ->complete() and
disable/enable interrupts in ->suspend()/->resume().
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the probe drivers have already set the dma_mask, not
replacing the value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3's GUID register is supposed to be used to write
any sort of version we might want. It helps when getting
bug reports for platforms you don't have HW to know
which kernel version of the driver was running on the
platform.
Because we don't really track driver version, but we _do_
track the kernel version, let's write LINUX_VERSION_CODE to
that register and use it for debugging.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On ISOC endpoints the last trb_pool entry used as a
LINK TRB is not getting zeroed out correctly due to
memset being called incorrectly and in the wrong place.
If pool allocated from DMA was not zero-initialized
to begin with this will result in the size and ctrl
values being random garbage. Call memset correctly after
assignment of the trb_link pointer.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts")
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 02dae36aa6.
That commit is bogus in two ways:
1) There's no way dwc3-omap's ->suspend() can cause any effect
on xhci's ->suspend(). Linux device driver model guarantees
that a parent's ->suspend() will only be called after all
children are suspended. dwc3-omap is the parent of the
parent of xhci.
2) When implementing Deep Sleep states where context is lost,
USBOTGSS_IRQ0 register, well, looses context so we
_must_ rewrite it otherwise core IRQs will never be
reenabled and USB will appear to be dead.
Fixes: 02dae36 (usb: dwc3: dwc3-omap: Disable/Enable only
wrapper interrupts in prepare/complete)
Cc: <stable@vger.kernel.org> # v3.17
Cc: George Cherian <george.cherian@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to Section 8.5.3.2 of the USB 2.0 specification,
a USB device must terminate a Data Phase with either a
short packet or a ZLP (if the previous transfer was
a multiple of wMaxPacketSize).
For reference, here's what the USB 2.0 specification, section
8.5.3.2 says:
"
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase
in which the host requests more data than is contained
in the specified data structure. When all of the data
structure is returned to the host, the function should
indicate that the Data stage is ended by returning a
packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of
wMaxPacketSize for the pipe, the function will return
a zero-length packet to indicate the end of the Data
stage.
"
Signed-off-by: Felipe Balbi <balbi@ti.com>
if our list of requests is empty, return early.
There's really nothing to be done in case our
request list is empty anyway because the only
situation where we our list is empty, is when
we're transferring ZLPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The device controller is the same but it has different PCI ID. Add this new
ID to the driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to our Gadget Framework API documentation,
->set_halt() *must* return -EAGAIN if we have pending
transfers (on either direction) or FIFO isn't empty (on
TX endpoints).
Fix this bug so that the mass storage gadget can be used
without stall=0 parameter.
This patch should be backported to all kernels since v3.2.
Cc: <stable@vger.kernel.org> # v3.2+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of releasing the lock and calling locked
versions of our set_halt() methods, let's hold
the lock all the way through and call unlocked
versions of those functions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
__dwc3_gadget_ep_set_halt() is the function which
handles the actual halt feature. In order to cope
with some extra cleanup comming as a follow-up patch
let's move the isochronous endpoint check there too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_ep0_set_halt() will be called without
locks held in some cases, so we must hold the lock
on our own. While at that, also add a version without
locks to be called in certain conditions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.
All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 glue layer is hardware layer around Synopsys DesignWare
USB3 core. Its purpose is to supply Synopsys IP with required
clocks, voltages and interface it with the rest of the SoC.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUDOW+AAoJEHm+PkMAQRiGOXYH/00TPKm8PdM5cXXG2YYYv9eT
W99K7KD2i0/qiVtlGgjjvB7fO3K0HcZusTd2jmVd8IWntXvauq7Zpw5YZkjwu4KX
Y1HCwwCd2aw0FoqgrJhNP3+j5Cr1BD/HLtbffjCe+A3tppOIis4Bwt2wJOoYlXpS
hU9Jxxc4lcRo8YKbffouDo7PIneWeJy8N+WGpUR5BfJIEK0ZZtCUqn3/3WLX4FYu
fE6uiF/bACTpKXU/mo4dDbhZp439H/QdwQc9B0F8+8CBDMXKaNHrPV7kN36T2SWa
fD4boikTsi/yh9Ks1fvHbvNq2N0ihoMnja+vLRyvjAcAQv2fKG3OZtYgFWSdghU=
=Xknd
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rc4' into next
Merge Linux 3.17-rc4 here so we have all the latest
fixes on next too. This also cleans up a few conflicts
when applying patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/Makefile
drivers/usb/gadget/function/Makefile
drivers/usb/gadget/legacy/Makefile
drivers/usb/phy/phy-samsung-usb.h
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It manages the powerdown signal,
and configures the internal glue logic and syscfg registers.
[ balbi@ti.com : actually switch over to of_platform_depopulate() ]
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we're debugging hard-to-reproduce and time-sensitive
use cases, printk() poses too much overhead. That's when
the kernel's tracing infrastructure comes into play.
This patch implements a few initial tracepoints for the
dwc3 driver. More traces can be added as necessary in order
to ease the task of debugging dwc3.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Those functions are only using within debugging
messages, grouping them into debug.h makes sense.
While at that, also add missing multiple inclusion
guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
After commit 2ec2a8be (usb: dwc3: gadget:
always enable IOC on bulk/interrupt transfers)
we created a situation where it was possible to
hang a bulk/interrupt endpoint if we had more
than one pending request in our queue and they
were both started with a single Start Transfer
command.
The problems triggers because we had not enabled
Transfer In Progress event for those endpoints
and we were not able to process early giveback
of requests completed without LST bit set.
Fix the problem by finally enabling Xfer In Progress
event for all endpoint types, except control.
Fixes: 2ec2a8be (usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers)
Cc: <stable@vger.kernel.org> # v3.14+
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we don't to gate clocks until our children are
done with their remove path.
Fixes: af310e9 (usb: dwc3: omap: use runtime API's to enable clocks)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can't suspend the PHYs before dwc3_core_exit_mode()
has been called, that's because the host and/or device
sides might still need to communicate with the far end
link partner.
Fixes: 8ba007a (usb: dwc3: core: enable the USB2 and USB3 phy in probe)
Cc: <stable@vger.kernel.org> # v3.9+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.
Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.
Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
dep->endpoint.desc is checked at the beginning of
dwc3_gadget_ep_queue(), but after that it may be set to NULL
by another thread and then accessed again in dwc3_gadget_ep_queue().
This will lead to kernel oops.
Expand spinlock protection area to aviod race condition.
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"ret" should be signed. It's only used for zero and negative error
codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Move the extcon related code to its own function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move find and set the utmi mode to its own separate function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move map offset to its own separate function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the x_major calculation logic from the wrapper revision register
to differentiate between OMAP5 and AM437x. This was done to find the
register offsets of wrapper register. Now that We do it using dt
compatible, remove the whole logic.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove 'start_new' variable from dwc3_endpoint_transfer_complete(),
since this variable has not been used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All dwc3 based xhci host controller supports USB3.0 LPM functionality.
Therefore enable it in platform data for all dwc3 based xhci device if
DWC3_HOST_USB3_LPM_ENABLE is selected in Kconfig.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer DWC3 controllers can be built for USB 2.0-only mode, where
most of the USB 3.0 circuitry is left out. To support this mode,
the driver must limit the speed programmed into the DCFG register
to Hi-Speed or lower.
Reads and writes to the PIPECTL register are left as-is, since
they should be no-ops in USB 2.0-only mode. Calls to phy_init()
etc. for the USB3 phy are also left as-is, since the no-op USB3
phy should be used for USB 2.0-only mode controllers.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Putting together the code related to getting the 'IORESOURCE_MEM'
and assigning the same to dwc->xhci_resources, for increasing
the readability.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc3 wrapper driver should not be fiddling with the core interrupts.
Disabling the core interrupts in prepare stops xhci from proper operation.
So remove disable/enable of core interrupts from prepare/complete.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In ISOC transfers, when free_slot points to the last TRB (i.e. Link
TRB), and all queued requests meet Missed Interval Isoc error, busy_slot
points to trb0.
busy_slot->trb0
trb1
...
free_slot->trb31(Link TRB)
After end transfer and receiving the XferNotReady event, trb_left is
caculated as 1 which is wrong, and no TRB will be primed to the
endpoint.
The root cause is free_slot is not increased the same way as busy_slot.
When busy_slot is increased by one, it checks if points to a link TRB
after increasement, but free_slot checks it before increasement.
free_slot should behave the same as busy_slot to make the trb_left
caculation correct.
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q1jA
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.16 merge window
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy-mv-u3d-usb.c
This fixes a bug when dwc3_pci_register_phys() fails and leaves device enabled.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
First usage of ret variable will re-write initial value. Thus, there is no need
to initialize it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this makes it slightly easier to read generic CMD
logs. It also helps make sure we're sending proper
parameters for each command.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Facilitate getting required 3.3V and 1.0V VDD supply for
DWC3 controller on Exynos.
With patches for regulators' nodes merged in 3.15:
c8c253f ARM: dts: Add regulator entries to smdk5420
275dcd2 ARM: dts: add max77686 pmic node for smdk5250,
certain perripherals will now need to ensure that,
they request VDD regulators in their drivers, and enable
them so as to make them working.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Glue layers for the DWC3 driver only make sense on specific platforms.
Add dependencies so that they are not built where they aren't needed.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
no functional changes, just renaming the function
in order to make it slightly clearer what it should
be used for, also matching the driver name.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move mode (Host, Peripheral, OTG) initialization
to its own function in order to decrease the size
of our probe() routine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
our probe() routine is too large and we can
easily refactor PHY-related code out to another
function to make it slightly less painful to read.
Signed-off-by: Felipe Balbi <balbi@ti.com>
so it seems like DWC3 IP doesn't clear stalls
automatically when we disable an endpoint, because
of that, we _must_ make sure stalls are cleared
before clearing the proper bit in DALEPENA register.
Cc: <stable@vger.kernel.org> # v3.4+
Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make dwc3_gadget_resize_tx_fifos() iterate only over IN
endpoints that are actually present, based on the
num_in_eps parameter. This terminates the loop so as to
prevent dereferencing a potential NULL dwc->eps[i] where
i >= (num_in_eps + num_out_eps).
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7AbcACgkQMUfUDdst+ymbZACgncdbZyPsVZ7ZUpBFNbO/vBVT
T9UAmwciojEzjh7b+x4ylsWH+O3LWVN3
=RpAF
-----END PGP SIGNATURE-----
Merge tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while"
* tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (249 commits)
xhci: Transition maintainership to Mathias Nyman.
USB: disable reset-resume when USB_QUIRK_RESET is set
USB: unbind all interfaces before rebinding any
usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210
usb: gadget: tcm_usb_gadget: stop format strings
usb: gadget: f_fs: add missing spinlock and mutex unlock
usb: gadget: composite: switch over to ERR_CAST()
usb: gadget: inode: switch over to memdup_user()
usb: gadget: f_subset: switch over to PTR_RET
usb: gadget: lpc32xx_udc: fix wrong clk_put() sequence
USB: keyspan: remove dead debugging code
USB: serial: add missing newlines to dev_<level> messages.
USB: serial: add missing braces
USB: serial: continue to write on errors
USB: serial: continue to read on errors
USB: serial: make bulk_out_size a lower limit
USB: cypress_m8: fix potential scheduling while atomic
devicetree: bindings: document lsi,zevio-usb
usb: chipidea: add support for USB OTG controller on LSI Zevio SoCs
usb: chipidea: imx: Use dev_name() for ci_hdrc name to distinguish USBs
...
This patch move simply OF helper function to extcon core and change function
name as following:
- of_extcon_get_extcon_dev() -> extcon_get_edev_by_phandle()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
We know what "value" is and it upsets static checkers that we appear to
have doubts about it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These were cut and paste from the ->disconnect function.
Fixes commit 30d577b9bcc4 ('usb: dwc3: gadget: call gadget driver's
->suspend/->resume')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adapted dwc3 core to use the Generic PHY Framework. So for init, exit,
power_on and power_off the following APIs are used phy_init(), phy_exit(),
phy_power_on() and phy_power_off().
However using the old USB phy library wont be removed till the PHYs of all
other SoC's using dwc3 core is adapted to the Generic PHY Framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since PHYs for dwc3 is optional (not all SoCs having PHYs for DWC3
should be programmed), do not return from probe if the USB PHY library
returns -ENODEV as that indicates the platform does not have a
programmable PHY.
While this can be considered as a temporary fix, a long term solution
would be to add 'nop' PHY for platforms that does not have programmable
PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
few new revisions of the core have been released,
add them to our list of revisions so we can apply
workarounds if necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 388e5c5 (usb: dwc3: remove dwc3 dependency
on host AND gadget.) created the possibility for
host-only and peripheral-only dwc3 builds but
left a possible randconfig build error when host-only
builds are selected.
Cc: <stable@vger.kernel.org> # v3.8+
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When going into bus suspend/resume we _must_
call gadget driver's ->suspend/->resume callbacks
accordingly. This patch implements that very feature
which has been missing forever.
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's not always we need to force a transfer to be removed
from the core's internal cache. This extra argument will
help differentiating those two cases.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During superspeed, HIRD threshold should always
be zero. Curent driver wasn't making sure that
was the case.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we have hibernation configured, Databook
instructs us to set KEEP_CONNECT bit together
with RUN_STOP bit, in step 9 of section 12.3.6.1
Initialization for Hibernation Support.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We must read HWPARAMS4 register to figure out
how many scratch buffers we should allocate.
Later patch will use "Set Scratchpad Buffer
Array" command to pass the pointer to the
IP so it can be used during hibernation.
Signed-off-by: Felipe Balbi <balbi@ti.com>
That argument will be used in later patches when we
have working hibernation support. For now, always
pass it as false.
The idea of this patch is to decrease to size of
following patches and slowly add hibernation building
blocks to the gadget side of dwc3 so that it becomes
very easy to review the actual hibernation code.
[ balbi@ti.com : rewrote patch on top of current
tree. Added commit log. ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This function will be used during hibernation to get
the current link state. It will be needed at least
for Hibernation support.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This extra field will save endpoint state when we're
about to enter hibernation. It will be used later
to restore the endpoint state when resuming.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
move 1-bit flags to the bottom of the structure,
sort all bit flags alphabetically, add documentation
which was missing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Revision 2.20a of the core has a known issue
which would generate bogus hibernation events
_and_ random failures on USB CV TD.9.23 test
case.
The suggested workaround is to ignore hibernation
events which don't match currently connected
speed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Revisions between 2.10a and 2.50a (included) have
a known issue which may cause xHCI compliance tests
to fail and/or quality issues with Isochronous
transactions.
Note that this issue only impacts certain configurations
of those revisions, namely the ones which have clock
gating enabled.
The suggested workaround is to disable clock gating in
known broken revisions, make sure HW LPM is disabled
and set GCTL.SOFITPSYNC to 1.
Signed-off-by: Felipe Balbi <balbi@ti.com>
by setting IOC always, we can recycle TRBs a
lot sooner at the expense of some increased
CPU load.
The extra load seems to be quite minimal on
OMAP5 devices (instead of 1 IRQ for one MSC
transfer, we get
CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS).
Signed-off-by: Felipe Balbi <balbi@ti.com>
Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.
Because of that, what used to be 8 bits long, has become 9 bits long.
Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.
So in dwc3_event_devt, the bit mask should be:
event_info [24:16] 9 bits
reserved31_25 [31:25] 7 bits
This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.
[ balbi@ti.com : improve commit log a bit ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSt1TYAAoJEHm+PkMAQRiGvWgH/iWg8TmEWz4KUKuHthuUi0uh
9+2YDN+4k577Xa0obaG24giQeqkCdxMr3oJrS3FO9jeAmaNRHEGhxUPneisb7RtN
9jIVsz5bPa9/DcK9nqtaUQdvA0O5AWTE6AAPmwleTVy+8CygBo987T2uGELnQCSR
FrKCrMePc7Pj0uthMVXrpJ17Ffm/j7jkfRtPhrxHJyngh3jEux+tPbpynH/aKuO2
47unsSQimoFk7n2SPFvNu3E/vZE2xVbu5SH9MCl5yyiCifFjpi3B71LV/FW51lvm
cK8Jzn2BmYDygRFjnZfq4zJHqYJCBHzpjCLWmR37Dm/JS91aGq3+Cg0stDP8UTs=
=+Hcn
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc5' into next
Linux 3.13-rc5
* tag 'v3.13-rc5': (231 commits)
Linux 3.13-rc5
aio: clean up and fix aio_setup_ring page mapping
aio/migratepages: make aio migrate pages sane
aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
Don't set the INITRD_COMPRESS environment variable automatically
mm: fix build of split ptlock code
pstore: Don't allow high traffic options on fragile devices
mm: do not allocate page->ptl dynamically, if spinlock_t fits to long
mm: page_alloc: revert NUMA aspect of fair allocation policy
Revert "mm: page_alloc: exclude unreclaimable allocations from zone fairness policy"
mm: Fix NULL pointer dereference in madvise(MADV_WILLNEED) support
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events
ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
mm/hugetlb: check for pte NULL pointer in __page_check_address()
fix build with make 3.80
...
Conflicts:
drivers/usb/phy/Kconfig
The reset_gpio member of the usb_phy_gen_xceiv_platform_data
structure needs the have negative value or phy-generic's
probe will fail unless DT is used. 0 is a valid gpio number.
This fixes an issue where phy-generic fails to probe with
message: "usb_phy_gen_xceiv.0: Error requesting RESET GPIO 0".
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into next
Linux 3.13-rc4
* tag 'v3.13-rc4': (1001 commits)
Linux 3.13-rc4
null_blk: mem garbage on NUMA systems during init
radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh()
Revert "selinux: consider filesystem subtype in policies"
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
ARM: fix asm/memory.h build error
dm array: fix a reference counting bug in shadow_ablock
dm space map: disallow decrementing a reference count below zero
mm: memcg: do not allow task about to OOM kill to bypass the limit
mm: memcg: fix race condition between memcg teardown and swapin
thp: move preallocated PTE page table on move_huge_pmd()
mfd/rtc: s5m: fix register updating by adding regmap for RTC
rtc: s5m: enable IRQ wake during suspend
rtc: s5m: limit endless loop waiting for register update
rtc: s5m: fix unsuccesful IRQ request during probe
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
include/linux/kernel.h: make might_fault() a nop for !MMU
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
...
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds "maxpacket_limit" to struct usb_ep. This field contains
maximum value of maxpacket supported by driver, and is set in driver probe.
This value should be used by autoconfig() function, because value of field
"maxpacket" is set to value from endpoint descriptor when endpoint becomes
enabled. So when autoconfig() function will be called again for this endpoint,
"maxpacket" value will contain wMaxPacketSize from descriptior instead of
maximum packet size for this endpoint.
For this reason this patch adds new field "maxpacket_limit" which contains
value of maximum packet size (which defines maximum endpoint capabilities).
This value is used in ep_matches() function used by autoconfig().
Value of "maxpacket_limit" should be set in UDC driver probe function, using
usb_ep_set_maxpacket_limit() function, defined in gadget.h. This function
set choosen value to both "maxpacket_limit" and "maxpacket" fields.
This patch modifies UDC drivers by adding support for maxpacket_limit.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 requires epout to have buffer size aligned to MaxPacketSize value.
This patch sets necessary quirk for it.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
the lock was only taken inside the hardirq
handler, which runs with IRQs disabled. There's
no chance of any race condition happening, even
on SMP machines. It's safe to remove that
spinlock.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to inter dependencies of I2C and extcon by the time dwc3
checks for extcon device its not registered especially in case of J6.
In O5 the vbus regulator save us from getting to this point.
So for tiime being return PROBE_DEFER if extcon is enabled in dt.
Signed-off-by: George Cherian <george.cherian@ti.com>
usb phy was power'ed on but was never power'ed off in the error path.
Fix it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usb_phy_set_suspend(phy, 0) is called before usb_phy_init. Fix it.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc3 UDC driver doesn't implement endpoint wedging correctly.
When an endpoint is wedged, the gadget driver should be allowed to
clear the wedge by calling usb_ep_clear_halt(). Only the host is
prevented from resetting the endpoint.
This patch fixes the implementation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=LDY7
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
These aren't necessary after switch and if blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This delay got introduced in:
"7415f17 usb: dwc3: core: add power management support"
which reflected similar code in dwc3_core_soft_reset() function.
However, originally the delay of 100ms in dwc3_core_soft_reset() was
meant to assist USB2PHY and USB3PHY reset, not for usb_phy_init()
sequence.
We should get rid of this delay, since things will still work
fine without this.
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dwc3_gadget_init_endpoint() fails after allocate some of the eps, we
need to free their memory to avoid leak.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is required by the OMAP glue driver, but it already depends
on it. The core driver should not depend on it. This will
allow the use of the PCI glue driver again.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in the
shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlH58ACgkQMUfUDdst+ymTGwCdH1BmMdypyjUBxJEoWNDUuwXn
/AQAoKt329vmB6qn41rvaTilHHYUXS7H
=ovaW
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in
the shortlog"
* tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (62 commits)
drivers: uio: Kconfig: add MMU dependancy for UIO
drivers: uio: Add driver for Humusoft MF624 DAQ PCI card
drivers: uio_pdrv_genirq: use dev_get_platdata()
drivers: uio_pruss: use dev_get_platdata()
drivers: uio_dmem_genirq: use dev_get_platdata()
drivers: parport: Kconfig: exclude h8300 for PARPORT_PC
drivers: misc: ti-st: fix potential race if st_kim_start fails
Drivers: hv: vmbus: Do not attempt to negoatiate a new version prematurely
misc: vmw_balloon: Remove braces to fix build for clang.
Drivers: hv: vmbus: Fix a bug in the handling of channel offers
vme: vme_ca91cx42.c: fix to pass correct device identity to free_irq()
VMCI: Add support for virtual IOMMU
VMCI: Remove non-blocking/pinned queuepair support
uio: uio_pruss: remove unnecessary platform_set_drvdata()
parport: amiga: remove unnecessary platform_set_drvdata()
vme: vme_vmivme7805.c: add missing __iomem annotation
vme: vme_ca91cx42.c: add missing __iomem annotation
vme: vme_tsi148.c: add missing __iomem annotation
drivers/misc/hpilo: Correct panic when an AUX iLO is detected
uio: drop unused vma_count member in uio_device struct
...
if pdata is a NULL pointer we could cause a
kernel oops when probing the driver. Make sure
to cope with systems which won't pass pdata
to the driver.
Tested-by: Paul Zimmerman <paulz@synopsys.com>
Reported-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "nop" driver isn't a do-nothing-stub but supports a couple functions
like clock on/off or is able to use a voltage regulator. This patch
simply renames the driver to "generic" since it is easy possible to
extend it by a simple function istead of writing a complete driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Modified dwc3-omap to receive connect and disconnect notification using
extcon framework. Also did the necessary cleanups required after
adapting to extcon framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled. Unnecessary CONFIG_PM ifdefs
are removed.
drivers/usb/dwc3/dwc3-pci.c:215:12: warning: 'dwc3_pci_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-pci.c:224:12: warning: 'dwc3_pci_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the wrapper function for retrieving the
platform_data instead of accessing dev->platform_data
directly.
While at that also make change 'node' initialization
to use the dev pointer.
Inspired-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When deferred probe happens driver will try to ioremap multiple times
and will fail. Memory resource.start variable is a global variable,
modifications in this field will be accumulated on every probe.
Fix this by moving the above operations after driver hold all
required PHY's.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
before changing to configured state, we need
to wait until gadget driver has had a chance
to process the request.
In case of USB_GADGET_DELAYED_STATUS, that means
we need to defer usb_gadget_set_state() until
the upcoming usb_ep_queue().
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we're switching back to USB_STATE_ADDRESS
from USB_STATE_CONFIGURED (if host sends
a set configuration command for configuration
zero), we should only switch if the request
is successfully processed by the gadget driver.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
that function isn't really processing any event
buffer, rather just checking whether it contains
events to be processed.
Due to that reason, we're reaning it to dwc3_check_event_buf()
instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can make use of bit 31 of the GEVNTSIZ(n)
registers to mask/unmask interrupts from that
particular interrupter.
With that feature, we can easily drop IRQF_ONESHOT
from our driver which makes it possible to
properly change IRQ priorities when using RT
patchset *and* it allows us to make use of the
scheduler to choose the proper time to handle
this IRQ thread.
Signed-off-by: Felipe Balbi <balbi@ti.com>
That register has more than just the event buffer
size; we can also mask and unmask that particular
interrupter on bit 31 of that register.
In this patch we introduce the necessary macros
and make sure to use the new macros while also
making sure we mask interrupts during driver
removal.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the macro DWC3_DCFG_LPM_CAP was defined twice.
This patch just removes one of the definitions,
no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
that way we get debugging information when
enabling verbose debug of the driver.
It will be no-op otherwise.
Signed-off-by: Felipe Balbi <balbi@ti.com>
by moving that dev_vdbg() to the internal
__dwc3_gadget_ep_enable() we get the print
even when enable ep0, which calls the internal
function directly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Recent versions of the core, can suspend and resume
the PHYs automatically, so we don't need to fiddle
with dwc3's Global PHY registers at all.
On versions prior to 1.94a this patch will mean
that we will never ask dwc3 to suspend the PHY.
This is an acceptable behavior or such old versions
of the core, specially considering that the only
chip known to have a version prior to 1.94a was
OMAP5 ES1.0 and that's not supported in mainline
kernel, because it was just a test spin of OMAP5.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adapts the dwc3 to use the device tree helper
"of_usb_get_dr_mode" for the mode of operation of the dwc3 instance
being probed.
[ balbi@ti.com : make of_usb_get_dr_mode() conditional on
dev->of_node and let pdata pass dr_mode too ]
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
all other drivers using Synopsys IPs with DT
have a compatible of snps,$driver, in order
to add consistency, we are switching over to
snps,dwc3 but keeping synopsys,dwc3 in the core
driver to maintain backwards compatibility.
New DTS bindings should NOT use synopsys,dwc3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
in order to allow different instances of the
core work in different maximum speeds, we will
move the maximum_speed module_parameter to
both DeviceTree (making use the new maximum-speed
DT property) and platform_data.
Signed-off-by: Felipe Balbi <balbi@ti.com>
in case we're not in a DT boot, we should
still be able to tell the driver how to behave.
In order to be able to pass flags to the driver,
we introduce platform_data structure which the
core driver should use.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a Linux-only driver which makes use
of GPL-only symbols. It makes no sense to
maintain Dual BSD/GPL licensing for this driver.
Considering that the amount of work to use this
driver in any different operating system would likely
be as large as developing the driver from scratch and
considering that we depend on GPL-only symbols, we
will switch over to a GPL v2-only license.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
@list is not as a parameter of dwc3_event_buffer, so remove it in
comments.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We cannot request an IRQ with spinlocks held
as that would trigger a sleeping inside
spinlock warning.
Cc: <stable@vger.kernel.org> # v3.10
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Glue layers are starting to have separate
requirements. For example, OMAP's glue layer
is starting to use extcon framework which
no one else needs.
In order to make it clear the proper dependencies,
we are now allowing glue layers to be selectable
so that each glue layer can list their own dependencies
without messing with the core IP driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If NO_DMA=y:
drivers/built-in.o: In function `dwc3_free_one_event_buffer':
drivers/usb/dwc3/core.c:132: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `dwc3_alloc_one_event_buffer':
drivers/usb/dwc3/core.c:154: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `dma_set_coherent_mask':
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
drivers/built-in.o: In function `dwc3_free_trb_pool':
drivers/usb/dwc3/gadget.c:407: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `dwc3_gadget_exit':
drivers/usb/dwc3/gadget.c:2693: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `dwc3_alloc_trb_pool':
drivers/usb/dwc3/gadget.c:391: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `dwc3_gadget_init':
drivers/usb/dwc3/gadget.c:2598: undefined reference to `dma_alloc_coherent'
drivers/usb/dwc3/gadget.c:2667: undefined reference to `dma_free_coherent'
drivers/usb/dwc3/gadget.c:2674: undefined reference to `dma_free_coherent'
drivers/usb/dwc3/gadget.c:2678: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When there is an error with the usb3_phy probe or absence, the error returned
is erroneously for usb2_phy.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Per dwc3 2.50a spec, the is_devspec bit is used to distinguish the
Device Endpoint-Specific Event or Device-Specific Event (DEVT). If the
bit is 1, the event is represented Device-Specific Event, then use
[7:1] bits as Device Specific Event to marked the type. It has 7 bits,
and we can see the reserved8_31 variable name which means from 8 to 31
bits marked reserved, actually there are 24 bits not 25 bits between
that. And 1 + 7 + 24 = 32, the event size is 4 byes.
So in dwc3_event_type, the bit mask should be:
is_devspec [0] 1 bit
type [7:1] 7 bits
reserved8_31 [31:8] 24 bits
This patch should be backported to kernels as old as 3.2, that contain
the commit 72246da40f "usb: Introduce
DesignWare USB3 DRD Driver".
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we fail our ->udc_start() callback, we
should be ready to accept another modprobe following
the failed one.
We had forgotten to clear dwc->gadget_driver back
to NULL and, because of that, we were preventing
gadget driver modprobe from being retried.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRuODuAAoJEIaOsuA1yqREEYMP/212PIcMM/niwl2T97l+Ispc
EVe8ebg69/t+LjEHmipyw00HvBuGv+6ccJbuU+NBSSi229iIkxXlE+Q7MoywHOZg
eSozqiIXIotkNTPg4vT6YfWspyNaoiDrl9TK3KMP9SyctlgxqMdcfke5dqpGpdUP
xqYhWCAbZ6uvu6Lq6r3NwX1pMKhXxbnTDCY77YOCb/H8UPlSHSW4nwjAKYvsEWwD
RLXn0UKDZF4FRm296ftIHDD8rDazCaQPkkglQejFrqheNpbR7SUkC672veca7xF5
2iaWS62p7SWDHsfzyLpeJwoglHcxRa3E8ZqdT9ALvrimMTm0jVM0pzDSCF2xBpFq
UP78YX2S94o/YC8NXfp6GMf5CFSlLDxQ7oahcUpUBVtx5l2v8bfyb2/KOrB6kHBS
v8RJqFbcYXHHygaYS0oXGqKg2ScwYeVIenlrk8ByPrfkJqS3v7CKLB0wNrV5ZWyC
nnfyMF+bW+M00nb9jKjS+Utni8looKpWdKcmAdP/zPVKDZE5zh5WL2q/zWepWdgP
8nIslvivXmAkNs8wN5ji/E/w9qqkXiYCVkSQXfXPgBLWesaQqBR2geRWduSetKSm
AHINjU4+wXkRR0V1HyKzn+b1v5yZ5ksV7n5SXltyXKNeO0IeBDHNBHRVPFqHdgau
u2prz3aPvqEFENqgr7z5
=O9AH
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.11 merge window
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
This patch adds wrappers to dwc3_omap_readl/writel calls to accomodate
both OMAP5 and AM437x reg maps (It uses the cached register offsets).
Also renames OMAP5 IRQ1 as IRQMISC and IRQ1 bits as IRQMISC bits.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch Initializes the register offset values depending
on the X_MAJOR of USBOTGSS_REVISION register. Also adds register
offset defines and new debug register defines.
X_MAJOR is 2 for both OMAP5 and AM437x. But both have different
glue register layout. Differentiate AM437x using dt compatible.
Register offsets are cached in dwc3_omap struct for reg reads
and writes.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AM437x and OMAP5 dwc3 subsytem have different register map.
Major differences are as follows.
OMAP5 has one main interrupt and one misc interrupt
Aegis has four main interrupts and one misc interrupt.
Miscellanous Interrupt offsets are changed.
UTMI OTG Control and Status Registers offsets are changed.
DEBUG Configuration and Status Registers are changed.
The main intend of the patch is to re-use the same wrapper driver
for both OMAP5 and AM437x, by using the x_major in revision
register and adjusting the offsets.
This patch adds the register map offsets and adds offset variables
in struct dwc3_omap to cache the offsets
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Improved the error handling of dwc3_omap_probe so that on error
conditions dwc3_omap is left in the original state.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pci_enable_device() will set device power state to D0,
so it's no need to do it again in dwc3_pci_probe().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we never allocate a TRB pool for physical endpoints
0 and 1 so trying to free it (a invalid TRB pool pointer)
will lead us in a warning while removing dwc3.ko module.
In order to fix the situation, all we have to do is skip
dwc3_free_trb_pool() for physical endpoints 0 and 1 just
as we while deleting endpoints from the endpoints list.
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the glue layer is removed first (core layer later),
it deletes the phy device first, then the core device.
But at core's removal, it still uses PHY's resources, it may
cause kernel's oops. It is much like the problem
Paul Zimmerman reported at:
http://marc.info/?l=linux-usb&m=136547502011472&w=2.
Besides, it is reasonable the PHY is deleted at last as
the controller is the PHY's user.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the glue layer is removed first (core layer later),
it deletes the phy device first, then the core device.
But at core's removal, it still uses PHY's resources, it may
cause kernel's oops. It is much like the problem
Paul Zimmerman reported at:
http://marc.info/?l=linux-usb&m=136547502011472&w=2.
Besides, it is reasonable the PHY is deleted at last as
the controller is the PHY's user.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Many USB host drivers contain code such as:
if (!pdev->dev.dma_mask)
pdev->dev.dma_mask = &tegra_ehci_dma_mask;
... where tegra_ehci_dma_mask is a global. I suspect this code originated
in commit 4a53f4e "USB: ehci-tegra: add probing through device tree" and
was simply copied everywhere else.
This works fine when the code is built-in, but can cause a crash when the
code is in a module. The first module load sets up the dma_mask pointer,
but if the module is removed and re-inserted, the value is now non-NULL,
and hence is not updated to point at the new location, and hence points
at a stale location within the previous module load address, which in
turn causes a crash if the pointer is de-referenced.
The simplest way of solving this seems to be to copy the code from
ehci-platform.c, which uses the coherent_dma_mask as the target for the
dma_mask pointer.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit:
388e5c5 usb: dwc3: remove dwc3 dependency on host AND gadget
breaks compilation when
USB=y, USB_GADGET=m, USB_DWC3=y and USB_DWC3_DUAL_ROLE=y.
drivers/built-in.o: In function `dwc3_gadget_giveback':
drivers/usb/dwc3/gadget.c:271: undefined reference to `usb_gadget_unmap_request'
drivers/built-in.o: In function `__dwc3_gadget_kick_transfer':
drivers/usb/dwc3/gadget.c:1005: undefined reference to `usb_gadget_unmap_request'
drivers/built-in.o: In function `__dwc3_gadget_ep_queue':
drivers/usb/dwc3/gadget.c:1073: undefined reference to `usb_gadget_map_request'
drivers/built-in.o: In function `dwc3_gadget_reset_interrupt':
drivers/usb/dwc3/gadget.c:2165: undefined reference to `usb_gadget_set_state'
drivers/built-in.o: In function `dwc3_gadget_init':
drivers/usb/dwc3/gadget.c:2647: undefined reference to `usb_add_gadget_udc'
drivers/built-in.o: In function `dwc3_gadget_exit':
drivers/usb/dwc3/gadget.c:2681: undefined reference to `usb_del_gadget_udc'
drivers/built-in.o: In function `__dwc3_ep0_do_control_data':
drivers/usb/dwc3/ep0.c:929: undefined reference to `usb_gadget_map_request'
drivers/usb/dwc3/ep0.c:906: undefined reference to `usb_gadget_map_request'
drivers/built-in.o: In function `dwc3_ep0_set_config':
drivers/usb/dwc3/ep0.c:575: undefined reference to `usb_gadget_set_state'
drivers/built-in.o: In function `dwc3_ep0_set_address':
drivers/usb/dwc3/ep0.c:520: undefined reference to `usb_gadget_set_state'
drivers/usb/dwc3/ep0.c:522: undefined reference to `usb_gadget_set_state'
drivers/built-in.o: In function `dwc3_ep0_set_config':
drivers/usb/dwc3/ep0.c:556: undefined reference to `usb_gadget_set_state'
Making changes similar to patch:
71a5e61 usb: chipidea: fix and improve dependencies if usb host or gadget support is built as module
Let us limit the DWC3 mode to depend on corresponding usb-subsystem
and USB_DWC3.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled. Unnecessary CONFIG_PM ifdefs
are removed.
drivers/usb/dwc3/core.c:682:12: warning: 'dwc3_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/core.c:709:12: warning: 'dwc3_resume' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-omap.c:430:12: warning: 'dwc3_omap_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-omap.c:440:12: warning: 'dwc3_omap_resume' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-exynos.c:185:12: warning: 'dwc3_exynos_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-exynos.c:194:12: warning: 'dwc3_exynos_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
PHY layer no longer returns NULL. It will
return -ENXIO when PHY layer isn't enabled
and we can use that to bail out instead of
request a probe deferral.
Signed-off-by: Felipe Balbi <balbi@ti.com>
our global '_omap' pointer wasn't marked
static. This patch solves the following sparse
warning:
warning: symbol '_omap' was not declared. \
Should it be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
CC: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Used of_platform_populate() to create dwc3 core platform_device
from device tree data. Additionally some cleanup is also done.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
return -EPROBE_DEFER from dwc3_omap_mailbox in dwc3-omap.c, if the probe of
dwc3-omap has not yet been executed or failed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
*dma_mask* is not set for devices created from dt data. So filled dma_mask
for dwc3_omap device here. And dwc3 core will copy the dma_mask from its
parent.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the wrong OTG_EVT,OTG_EVTEN and OTG_STS register
offsets.
While at that, also add a missing register to debugfs regdump
utility.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
there are no more users of CONFIG_USB_OTG_UTILS
left in tree, we can remove it just fine.
[ kishon@ti.com : fixed a linking error due
to original patch forgetting to change
drivers/usb/Makefile ]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
hwparams2 holds the number of endpoints which
were selected during RTL generation, we can
use that on our driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that machines may select dwc3's working mode (HOST only,
GADGET only or DUAL_ROLE) via Kconfig, let's set dwc3's mode
based on that, rather than fixing it to whatever hardware
says.
This way we can skip initializing Gadget/Host in case
we are using Host-only/Gadget-only mode respectively.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In DWC3 versions < 2.50a configured without
Hibernation mode enabled, there will be an
extra link status change interrupt if device
detects host-initiated U3 exit.
In that case, core will generate an unnecessary
U3 -> RESUME transition which should be ignored
by the driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some new revisions of the DWC3 core have
been released, let's add our defines to help
implementing known erratas.
Signed-off-by: Felipe Balbi <balbi@ti.com>
when commit 388e5c5 (usb: dwc3: remove dwc3
dependency on host AND gadget.) changed the
way debugfs files are created, it failed to
note that 'mode' is necessary in Dual Role
mode only while 'testmode' and 'link_state'
are valid in Dual Role and Peripheral-only
builds. Fix this while also converting pre-
processor conditional to C conditionals.
Signed-off-by: Felipe Balbi <balbi@ti.com>
nobody should be modifying that structure and
debugfs has already being fixed to take const
arguments, so we won't cause any new compile
warnings.
Signed-off-by: Felipe Balbi <balbi@ti.com>
whenever we grab an unknown link_state we
were printing the entire register value as
a integer but that's hardly useful; instead,
let's print only the bogus state value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
by moving to threaded IRQs, we allow our IRQ
priorities to be configurable when running with
realtime patch. Also, since we're running in
thread context, we can call functions which
might sleep, such as sysfs_notify() without
problems.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds suspend and resume callbacks to exynos dwc3 driver as part of
power management support.
This change does gating of dwc3 clock during suspend/resume cycles.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Vikas C Sajjan <vikas.sajjan@linaro.org>
CC: Doug Anderson <dianders@chromium.org>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
[ balbi@ti.com : refreshed to current linus/master ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch implements basic suspend/resume
functionality for the OMAP glue layer.
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we're not using those fields of the structure,
might as well remove them.
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for basic power management on
the dwc3 driver. While there is still lots
to improve for full PM support, this minimal
patch will already make sure that we survive
suspend-to-ram and suspend-to-disk without
major issues.
Cc: Vikas C Sajjan <vikas.sajjan@linaro.org>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will be used during resume to verify
if we should reconnect our pullups or not.
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we don't need to enable IRQs until we have
a gadget driver loaded and ready to work,
so let's delay IRQ enable to ->udc_start()
and IRQ disable to ->udc_stop().
While at that, also move the related use of
request_irq() and free_irq().
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make the call to dwc3_event_buffers_setup()
and dwc3_event_buffers_cleanup() explicit,
so it's easier to implement PM.
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We don't need the ->register_my_device flag
anymore because all UDC drivers have been
properly converted.
Let's remove every history of it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that we have drivers for omap-usb2 phy and omap-usb3 phy, stop
using nop-usb-xceiv.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
omap5 is not going to have support for non-dt boot making the platform
data associated with dwc3 useless. Removed it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Includes few minor fixes in dwc3-omap like populating the compatible
string in a correct way, extracting the utmi-mode property properly and
changing the index of get_irq since irq of core is removed from hwmod
entry.
Also updated the documentation with dwc3-omap device tree binding
information.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[ balbi@ti.com : fix a compile warning introduced by
this commit ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/dwc3/ep0.c: In function `__dwc3_ep0_do_control_data':
drivers/usb/dwc3/ep0.c:905: error: `typeof' applied to a bit-field
Looks like a gcc-3.4.5/sparc64 bug.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
the params variables on dwc3_gadget_conndone_interrupt()
is only memset() to zero but never used in
that function, so we can safely drop the variable
and memset() call.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 3921426 (usb: dwc3: core: move
event buffer allocation out of
dwc3_core_init()) introduced a memory leak
of the coherent memory we use as event
buffers on dwc3 driver.
If the driver is compiled as a dynamically
loadable module and use constantly loads
and unloads the driver, we will continue
to leak the coherent memory allocated during
->probe() because dwc3_free_event_buffers()
is never called during ->remove().
Cc: <stable@vger.kernel.org> # v3.7 v3.8
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a couple of missing GENERIC_HARDIRQS dependencies to fix link
errors like below on s390:
ERROR: "devm_request_threaded_irq" [drivers/usb/gadget/mv_udc.ko] undefined!
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two new PHY drivers coming here: one for Samsung,
one for OMAP. Both architectures are adding USB3
support to mainline kernel.
The PHY layer now allows us to have mulitple PHYs
of the same type, which is necessary for platforms
which provide more than one USB peripheral port.
There's also a few cleanups here: removal of __dev*
annotations, conversion of a cast to to_delayed_work(),
and mxs-phy learns about ->set_suspend.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c796
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: xceiv: patches for v3.9 merge window
Two new PHY drivers coming here: one for Samsung,
one for OMAP. Both architectures are adding USB3
support to mainline kernel.
The PHY layer now allows us to have mulitple PHYs
of the same type, which is necessary for platforms
which provide more than one USB peripheral port.
There's also a few cleanups here: removal of __dev*
annotations, conversion of a cast to to_delayed_work(),
and mxs-phy learns about ->set_suspend.
Multiple dwc3 controllers will try to allocate multiple xhci-hcd
interfaces.
Changing platform device IDs from NONE to AUTO to support
such cases.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Multiple dwc3 probe calls try to allocate no_op_xceive platform
device. Having static IDs for these will throw sysfs error -EEXIST.
Changing these static platform device IDs to AUTO to enable
multiple dwc3 controller support on a SoC.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added dt support for dwc3 core and update the documentation with
device tree binding information. Getting a PHY is now done using
devm_usb_get_phy_by_phandle() for dt boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Stray statements where removed from dwc3 core.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enabled the USB2 and USB3 PHY in probe by calling usb_phy_set_suspend
and disabled the PHYs on driver removal. When PM is implemented this
will be optimized to enable the PHYs only when needed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add an API in the omap glue layer to write to the mailbox register which
can be used by comparator driver(twl). To pass the detection of the attached
device (signified by VBUS, ID) to the dwc3 core, dwc3 core has to write
to the mailbox regiter.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The runtime API's takes care of setting the SYSCONFIG register with
appropriate values. Hence explicit writes to SYSCONFIG register is
removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before accessing any register, runtime API's should be invoked to enable
the clocks. runtime API's are added here to prevent abort during register
access.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Used of_platform_populate() to create dwc3 core platform_device
from device tree data.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Used device_for_each_child() to handle child device (dwc3 core) removal
during devexit of dwc3 omap. This is in preparation for creating the child
devices from subnode of dwc3 omap glue using of_platform_populate.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using specific chip in compatible strings. Newer SOCs can claim
device by using older string in the compatible list.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
First of all, that 28 value makes no sense as
HIRD threshold is a 4-bit value, second of all
it's causing issues for OMAP5.
Using 12 because commit cbc725b3 (usb: dwc3:
keep default hird threshold value as 4b1100)
had the intention of setting the maximum allowed
value of 0xc.
Also, original code has been wrong forever, so
this should be backported as far back as
possible.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 controller curretly depends on USB && USB_GADGET.
Some hardware may like to use only host feature on dwc3,
or only gadget feature.
So, removing this dependency of USB_DWC3 on USB and USB_GADGET.
Adding the mode of operaiton of DWC3 also here
HOST/GADGET/DUAL_ROLE based on which features are enabled.
[ balbi@ti.com :
. make sure we have default modes for all possible Kernel
configurations.
. Remove the config -> menuconfig change as it's unnecessary
. switch over to IS_ENABLED() ]
CC: Doug Anderson <dianders@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I am not sure, why I found it during SG debugging. But, I noticed that
even when req_queued list was empty, there were some request in
request_list having queued flag true. If I run test second time, it
first removes all request from request_list and hence busy_slot was
wrongly incremented.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To work with scatter gather properly, fixes have been done in number of
functions. I will explain requirement of each fixes one by one.
start_slot: used to retrieve all request of SG during cleanup
dwc3_gadget_giveback: We need to skip link TRB if it was one of the
intermediate TRB of SG.
dwc3_prepare_one_trb: We need to track all submitted TRBs during
cleanup. Since, all TRBs would be serially allocated, so we can just
keep starting slot info and we can always find rest of them. We need to
pass sg node number, so that we cab appropriately program ISOC_FIRST/ISOC,
Chain etc.
dwc3_prepare_trbs: last_one should be set when it is last node
of SG as well as last node of request_list.
__dwc3_cleanup_done_trbs: It has been prepared after re-factorization of
dwc3_cleanup_done_reqs. It is called for each TRB of SG.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UPDATE_TRANSFER does not need any parameters. So, no need to prepare it.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we reach to link trb, we just need to increase free_slot and then
calculate TRB. Return is not correct, as it will cause wrong TRB DMA
address to fetch in case of update transfer.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were still some corner cases where isoc transfer was not able to
restart, specially when missed isoc does not happen , and in fact gadget does
not queue any new request during giveback.
Cleanup function calls giveback first, which provides a way to queue
another request to gadget. But gadget did not had any data. So , it did
not call ep_queue. To twist it further, gadget did not queue till
cleanup for last queued TRB is called. If we ever reach this scenario,
we must call END TRANSFER, so that we receive a new xfernotready with
information about current microframe number.
Also insure that there is no request submitted to core when issuing END
TRANSFER.
Cc: <stable@vger.kernel.org> # v3.8
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Its better to return from each if condition as they are mutually
exclusive.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are two reasons to generate missed isoc.
1. when the host does not poll for all the data.
2. because of application-side delays that prevent all the data from
being transferred in programmed microframe.
Current code was able to handle first case only. This patch handles
scenario 2 as well.Scenario 2 sometime may occur with complex gadget
application, however it can be easily reproduced for testing purpose as
follows:
a. use isoc binterval as 1 in f_sourcesink.
b. use pattern=0
c. introduce a delay of 150us deliberately in source_sink_complete, so
that after few frames it lands into scenario 2.
d. now run testusb 16 (isoc in test). You will notice that if this
patch is not applied then isoc transfer is not able to recover after
first missed.
Current patch's approach is as under:
If missed isoc occurs and there is no request queued then issue END
TRANSFER, so that core generates next xfernotready and we will issue a
fresh START TRANSFER.
If there are still queued request then wait, do not issue either END or
UPDATE TRANSFER, just attach next request in request_list during giveback.
If any future queued request is successfully transferred then we will issue
UPDATE TRANSFER for all request in the request_list.
Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Synopsys says:
The HIRD Threshold field must be set to ‘0’ when the device core is
operating in super speed mode.
This patch implements above statement.
Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_set_ep_config expects maxburst as incremented by 1. So, by
default initialize ep->maxburst to 1 for ep0.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently we're allocating an entire page to
serve as our event buffer. Provided our events
are 4 bytes long, it's very unlikely we will
even trigger 1k events at once.
Even in the worst case scenario where every
endpoint triggers one event and we still have
a couple of error events, that would still
be less than 40 events.
In order to cope with future versions of the
IP which could (or could not) increase the
amount of possible events to trigger
simultaneously, we're using an arbitrary size
of 64 events for our event buffer.
We're saving 3840 bytes by doing so.
Signed-off-by: Felipe Balbi <balbi@ti.com>
As with dwc_readl/writel, the global registers are specified as
offsets starting from the beginning of the xHCI address space,
but the memory region pointed to by dwc->regs already maps to
the start of the global addresses. Fix by offsetting each of the
regs relative to DWC3_GLOBALS_REGS_START.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 392142 moved event buffer allocation out of dwc3_core_init() but
event buffer allocation uses the cached copy of hwparams to determine
the number of event buffers and the caching is done in dwc3_core_init.
So moved dwc3_cache_hwparams function before dwc3_alloc_event_buffers so
that dwc3_alloc_event_buffers sees the correct number of event buffers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can finaly drop HAVE_CLK dependency from exynos glue layer
now that clk API provides no-op stubs when it's not linked
into the kernel.
We're also switching over event buffer allocation to devm_kzalloc()
and moving the allocation out of dwc3_core_init() so that can be
re-used when implementing PM support for v3.9.
After the introduction of PLATFORM_DEVID_AUTO, we can also drop the
homebrew platform device ID handling we had on dwc3 core and let
driver core take care of that for us.
Exynos glue layer learns about DeviceTree and drops platform_data
support completely.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=wqLI
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB dwc3 patches from Felipe:
"usb: dwc3: patches for v3.8
We can finaly drop HAVE_CLK dependency from exynos glue layer
now that clk API provides no-op stubs when it's not linked
into the kernel.
We're also switching over event buffer allocation to devm_kzalloc()
and moving the allocation out of dwc3_core_init() so that can be
re-used when implementing PM support for v3.9.
After the introduction of PLATFORM_DEVID_AUTO, we can also drop the
homebrew platform device ID handling we had on dwc3 core and let
driver core take care of that for us.
Exynos glue layer learns about DeviceTree and drops platform_data
support completely."
commit 380f0d2 (usb: dwc3: core: switch event
buffer allocation to devm_kzalloc()) was incomplete
leaving a trailing kfree(evt) in an error exit
path.
Fix this problem by removing the trailing kfree(evt).
Cc: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We are removing plat data which was used till now to init and
exit phy. We no longer need this since dwc3-core takes care of
initializing and shutting-down the phy using usb_phy_init()
and usb_phy_shutdown().
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support to parse probe data for
dwc3-exynos driver using device tree.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The lockless implementation of the unique id is quite impressive (:P)
but dirver's core can handle it, we can remove it and make our code a
little smaller.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 93abe8e (clk: add non CONFIG_HAVE_CLK routines)
added clk API stubs when !defined(CONFIG_HAVE_CLK).
This allows us to remove the HAVE_CLK dependency from
Exynos' glue layer and let it compile always.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We call usb_phy_init() from dwc3_core_init() during
probe, so adding usb_phy_shutdown() to dwc3_core_exit()
while removing the device so we don't keep PHYs
turned on, consuming power, unnecessarily.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If a USB transfer has already been started, meaning
we have already issued StartTransfer command to that
particular endpoint, DWC3_EP_BUSY flag has also
already been set.
When we try to cancel this transfer which is already
in controller's cache, we will not receive XferComplete
event and we must clear DWC3_EP_BUSY in order to allow
subsequent requests to be properly started.
The best place to clear that flag is right after issuing
DWC3_DEPCMD_ENDTRANSFER.
Cc: stable@vger.kernel.org # v3.4 v3.5 v3.6
Reported-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch is in preparation for adding PM support
dwc3 driver. We want to re-use dwc3_core_init and
dwc3_core_exit() functions on resume() and suspend()
callbacks respectively.
Moving even buffer allocation away from dwc3_core_init()
will allow us to reuse the event buffer which was allocated
long ago on our probe() routine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The rest of the driver is using devm_kzalloc() where possible
and this patch is just making event buffer allocation follow
the example.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some much needed changes for our dwc3 driver. First there's a
rework on the ep0 handling due to some Silicon issue we uncovered
which affects all users of this IP core (there's a missing
XferNotReady(DATA) event in some conditions). This issue which
show up as a SETUP transfers which wouldn't complete ever and
we would fail TD 7.06 of the Link Layer Test from USB-IF and
Lecroy's USB3 Exerciser.
We also fix a long standing bug regarding EP0 enable sequencing
where we weren't setting a particular bit (Ignore Sequence
Number). Since we never saw any problems caused by that, it
didn't deserve being sent to stable tree.
On this pull request we also fix Burst Size initialization which
should be done only in SuperSpeed and we were mistakenly setting
Burst Size to the maximum value on non-SuperSpeed mode. Again,
since we never saw any problems caused by that, we're not sending
this patch to stable.
There's also a memory ordering fix regarding usage of bitmaps in
dwc3 driver.
You will also find some sparse warnings fix, a fix for missed
isochronous packets when the endpoint is already busy, and a
fix for synchronization delay on dwc3_stop_active_transfer().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Lqwl
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.7 merge window
Some much needed changes for our dwc3 driver. First there's a
rework on the ep0 handling due to some Silicon issue we uncovered
which affects all users of this IP core (there's a missing
XferNotReady(DATA) event in some conditions). This issue which
show up as a SETUP transfers which wouldn't complete ever and
we would fail TD 7.06 of the Link Layer Test from USB-IF and
Lecroy's USB3 Exerciser.
We also fix a long standing bug regarding EP0 enable sequencing
where we weren't setting a particular bit (Ignore Sequence
Number). Since we never saw any problems caused by that, it
didn't deserve being sent to stable tree.
On this pull request we also fix Burst Size initialization which
should be done only in SuperSpeed and we were mistakenly setting
Burst Size to the maximum value on non-SuperSpeed mode. Again,
since we never saw any problems caused by that, we're not sending
this patch to stable.
There's also a memory ordering fix regarding usage of bitmaps in
dwc3 driver.
You will also find some sparse warnings fix, a fix for missed
isochronous packets when the endpoint is already busy, and a
fix for synchronization delay on dwc3_stop_active_transfer().
nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.
Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.
We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.
Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/qVp
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: xceiv: patches for v3.7 merge window
nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.
Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.
We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.
Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.
We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.
For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.
For those which don't provide controllable transceivers
we will register nop transceivers.
Note that once OMAP's transceiver drivers reach mainline,
this glue layer will change accordingly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.
For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If xfernotready is received and there is no request in request_list then
REQUEST_PENDING flag must be set, so that next request in ep queue is executed.
In case of isoc transfer, if xfernotready is already elapsed and even first
request has not been queued to request_list, then issue END TRANSFER, so that
you can receive xfernotready again and can have notion of current microframe.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Populate the resources for xhci afresh instead of directly using the
*struct resource* of core. *resource* structure has parent, sibling,
child pointers which should be filled only by resource API's. By
directly using the *resource* pointer of core in xhci, these parent,
sibling, child pointers are already populated even before
*platform_device_add* causing side effects.
Cc: stable@vger.kernel.org # v3.4, v3.5
Reported-by: Ruchika Kharwar <ruchika@ti.com>
Tested-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.
So, cache sync function must not be executed in case of ep0 bounced.
Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit removes USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED
Kconfig options. Since now kernel allows many UDC drivers to be
compiled, those options may turn to no longer be valid. For
instance, if someone decides to build UDC that supports super
speed and UDC that supports high speed only, the latter will be
"assumed" to support super speed since USB_GADGET_SUPERSPEED will
be selected by the former.
The test of whether CONFIG_USB_GADGET_*SPEED was defined was just
an optimisation which removed otherwise dead code (ie. if UDC is
not dual speed, there is no need to handle cases that can happen
if speed is high). This commit removes those checks.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When connection is established non-ss mode, endpoint.maxburst is correctly set
to 0, this means that current code will set maxburst bitfield on DEPCFG's
parameter 0 to the highest possible value (0x0f) which is wrong.
Even though this hasn't caused any issues so far (HW seems to ignore that when
not running in SS mode) we want to make sure maxburst bitfield is only set to
anything other than zero if we're running on SuperSpeed mode. In order to
achieve that, let's check for gadget's operating speed before setting maxburst
bitfield when issuing DEPCFG command.
[ balbi@ti.com : improved commit log a bit in order to clarify the situation ]
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As a bitmap is used for free/used. As a device freed
all memory operations must be scheduled before the bitmap
is manipulated.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case some gadget driver tries to enable an endpoint
which is already enabled, we print a nice WARN so we
can track broken gadget drivers. The only problem is that
we're printing the WARN when we already changed endpoint's
name, which would result in endpoints named as:
ep1in-bulk-bulk-bulk-bulk-bulk-bulk-bulk
To prevent that, we will continue to print the WARN,
but do so before changing endpoint's name and return
early.
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_stop_active_transfer has been called from two places. After each
calling of this function , we should allow 100 us delay to synchronize
with interconnect.
It would be better if we put this delay in that function only, rather
than into calling routine of this function.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Reported-by: Michel Sanches <michel.sanches@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When MISSED_ISOC is set, BUSY is also set. Since, we are handling
MISSED_ISOC as a separate case in third scenario, therefore handle only
BUSY but not MISSED_ISOC in second scenario.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following sparse warnings:
drivers/usb/dwc3/gadget.c:1096:7: warning: symbol 'ret' shadows an earlier one
drivers/usb/dwc3/gadget.c:1058:8: originally declared here
drivers/usb/dwc3/gadget.c:1100:16: warning: symbol 'dwc' shadows an earlier one
drivers/usb/dwc3/gadget.c:1057:15: originally declared here
drivers/usb/dwc3/gadget.c:1118:16: warning: symbol 'dwc' shadows an earlier one
drivers/usb/dwc3/gadget.c:1057:15: originally declared here
drivers/usb/dwc3/gadget.c:1800:19: warning: symbol 'dep' shadows an earlier one
drivers/usb/dwc3/gadget.c:1778:18: originally declared here
Also, fix the potential checkpatch errors around the if() loops that
this fix patch can create.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 68d3e66 (usb: dwc3: ep0: fix for possible early
delayed_status) added handling for early delayed status,
but the current code only works because so far delayed
status will always be on the IN direction.
This patch makes the code more robust by making sure that
we can handle all directions properly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to the late Silicon limitation found, we are
now pre-starting DATA phase's TRBs. If, still, we
get XferNotReady(DATA) we will ignore it unless
we're getting it for the wrong direction.
In that case we must keep the error case handling
plus add a ENDTRANSFER command to forcefully end
the Data TRB we started previously, then continue
to SetStall and so on.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We uncovered a limitation of this core WRT to the
Link Layer Compliance Suite's TD7.06.
On that test, host will start a GetDescriptor(DEVICE)
standard request, but it will do so only on the
SETUP phase, meaning there will *NOT* be any DATA or
STATUS phases.
The idea of the test is to verify robustness of the
IP WRT framing errors, so the test will send a
sequence of different SETUP_DPs each with a different
framing error and the Suite expects us to be able to
receive all SETUP_DPs with no timeouts.
This core, has the ability to tell us which phase the
host is expecting before we start it. Whenever we
receive a TP or DP when no transfers are cached on
the internal IP's caches, the IP will generate a
XferNotReady event with status informing us (in case
of physical ep0/ep1) if it's related to DATA or STATUS
phases - SETUP phase is expected to be prestarted.
Because we're always waiting for XferNotReady
events for DATA and STATUS phases, we will never
be able to know that the Host wants to start another
SETUP phase instead, which will render us "not
compliant" with TD7.06.
In order to "fix" the problem we must not rely
on XferNotReady events for the DATA phase and try
to always pre-start DATA transfers on physical
endpoints 0 and 1. If host goes back to SETUP phase
from DATA phase we will receive a XferComplete for
that phase with TRB's status set to SETUP_PENDING,
which is only useful for printing a debugging log as
the core expects us to still go through to the STATUS
phase, initiate a CONTROL_STATUS TRB just so it
completes right away and, only then, we go back to
the pending SETUP phase.
SNPS has decided to modify the programming model of
the core so that on-demand DATA phases will not be
supported anymore. Note that this limitation does not
affect 2-stage transfers, meaning that if TD7.06 would
start a 2-stage transfer instead of a 3-stage transfer,
we would receive a "fake" XferNotReady(STATUS) which
would complete right after being initiated with
SETUP_PENDING status.
Other endpoints are also not affected, so we can still
use on-demand transfers on Bulk/Isoc/Interrupt endpoints.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Databook doesn't say we should stall if we
get XferNotReady(STATUS) while we're expecting
something else.
Instead of stalling and restarting, tests have
proven that ignoring the event is far more
effective.
This problem has been caught while rewriting
ep0 handling in order we pass Link Layer TD7.6.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can return early from each if () branch
and split the special cases for clarity. While
at that also add a comment to the delayed_status
case.
Signed-off-by: Felipe Balbi <balbi@ti.com>
lots of changes for the dwc3 driver which will make
the driver a lot more stable and some changes which
are just cosmetic.
The bulk of changes is related to mis-defined macros
which were never used before, some fixes to error path
which e.g. prevent the driver from initiating two
transfer on ep0out in case of stall, some fixes to
request dequeueing and the End Transfer Command.
We have some changes to U1/U2 handling where we were
enabling those transtions at the wrong spot (though
we haven't seen a problem from that as of today).
A few patches will make it easier to add support for
newer releases of the core by adding definitions for
new registers and changing the code to act accordingly
when certain revisions are detected.
There's also the usual comestic changes to make the
driver easier to maintain and make it easier for new-
comers to understand the driver. Also one patch fixing
a double inclusion of a header.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=s04u
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.6 merge window
lots of changes for the dwc3 driver which will make
the driver a lot more stable and some changes which
are just cosmetic.
The bulk of changes is related to mis-defined macros
which were never used before, some fixes to error path
which e.g. prevent the driver from initiating two
transfer on ep0out in case of stall, some fixes to
request dequeueing and the End Transfer Command.
We have some changes to U1/U2 handling where we were
enabling those transtions at the wrong spot (though
we haven't seen a problem from that as of today).
A few patches will make it easier to add support for
newer releases of the core by adding definitions for
new registers and changing the code to act accordingly
when certain revisions are detected.
There's also the usual comestic changes to make the
driver easier to maintain and make it easier for new-
comers to understand the driver. Also one patch fixing
a double inclusion of a header.
This is quite a big pull request and contains patches
all over the place.
omap_udc is now a bit cleaner after removing omap2 support,
fixing some checkpatch.pl warnings and errors, switching over
to generic map/unmap routines and preventing a NULL pointer
de-reference.
s3c-hsotg has been switched over to devm_* API, got some
locking fixes and improvements and it also got an implementation
for the pullup() method.
the mass storage gadgets changed default value of the removable
parameter, dropped some unused options and made "file" and "ro"
module_parameters read-only in some cases.
ffs function got support for HID descriptor.
Some UDCs have been converted to clk_prepare_enable() and
clk_disable_unprepare().
Marvell now got support for its USB3 controller in mainline
after introducing its mv_u3d_core.c driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=hbE6
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: gadget: patches for v3.6 merge window
This is quite a big pull request and contains patches
all over the place.
omap_udc is now a bit cleaner after removing omap2 support,
fixing some checkpatch.pl warnings and errors, switching over
to generic map/unmap routines and preventing a NULL pointer
de-reference.
s3c-hsotg has been switched over to devm_* API, got some
locking fixes and improvements and it also got an implementation
for the pullup() method.
the mass storage gadgets changed default value of the removable
parameter, dropped some unused options and made "file" and "ro"
module_parameters read-only in some cases.
ffs function got support for HID descriptor.
Some UDCs have been converted to clk_prepare_enable() and
clk_disable_unprepare().
Marvell now got support for its USB3 controller in mainline
after introducing its mv_u3d_core.c driver.
Although timeout has never been experienced, still to make it
meaningful, its better to return error if it ever occurs.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As per databook, ACCEPT{U1,U2}ENA bits should be set after receiving
SetConfiguration Command.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
as per databook, these bits are cleared by hardware on each USB reset,
so no need to clear it explicitly by software in reset ISR.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
as per data book any HIRD threshold value greater than 4b1100 is
invalid. So set the maximum valid value as default values.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
set_halt for ep0 is called to stall a deferred control responses by the
gadget. We already have a function to stall default control endpoint.
This patch points set_halt for ep0 to the already available function.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Michel Sanches <michel.sanches@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we try to start an invalid test mode, we
will call dwc3_ep0_stall_and_restart() but we will
also call dwc3_ep0_out_start() which will start
a second transfer on ep0.
Let's prevent any problems by returning early in
the error case.
Signed-off-by: Felipe Balbi <balbi@ti.com>
whenever we want to stall ep0, we always call
dwc3_ep0_stall_and_restart() which makes sure
to send ep0state properly rendering the code
in __dwc3_gadget_ep_set_halt() duplicated.
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It makes it easier to read and also avoids
setting DWC3_EP_PENDING_REQUEST just so the
next branch evaluates true.
No functional changes otherwise.
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now we are sure that, if res_trans_idx is zero, then endpoint has been
stopped. So it's safe to just return if endpoint is already stopped. No
need to generate warning anymore.
While doing so, it's better to return when res_trans_idx is zero and
decrease one level of indentation.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
[ balbi@ti.com: slightly changed commit log ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Synopsys specification clearly states under section "Device Power-On or
Soft Reset" that DCTL.CSftRst=1 should be first step. So, just follow
what specification says.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before taking core out of reset phy must be stable. So wait for 100ms
after clear phy reset.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of ep_disable and reset interrupt is received and, still there
was at least one request queued for dma transfer, then endpoint is
stopped first. Once endpoint is stopped, callback for all queued
request must be called.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of ep_dequeue , if dequeued request was submitted for dma
transfer, then endpoint is stopped. Once endpoint is stooped, callback
for the dequeued request must be called.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
bMaxBurst field on endpoint companion descriptor
is supposed to contain the number of burst minus
1. When passing that to controller drivers, we
should be passing the real number instead (by
incrementing 1).
While doing that, also fix the assumption on
dwc3 that value comes decremented by one.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The definition of DWC3_DCTL_HIRD_THRES macro is
completely wrong. It will only work for when we
want to read the register's contents for that bitfield.
Change the macro so that it can be used to writing to
the register, and when we need to read, we can add
extra right shift of 24 bits.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
[ balbi@ti.com: add a commit log ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
By the time we're disabling the endpoint, HW
could already have posted more events to our
event buffer. In that case, we will receive
endpoint events for a disabled endpoint.
In order to protect ourselves from that situation,
we simply ignore endpoint interrupts whenever
the endpoint is disabled.
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we get disconnected, we will call gadget
driver's disconnect method, which should make
sure to disable all endpoints. At that point
we will call stop_active_transfers() to make
sure we didn't leave any pending request on the
controller.
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
That IRQ is causing way too much trouble. We have
a different handling which was agreed with IP
provider and has been tested with FPGA and OMAP5.
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We never set CMDIOC bit for Start Transfer
command, so that code will never be used.
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If event status says that its last completed TRB but TRB is still owned
by HW then break from the loop, because we are not going to get correct
TRB status from trb control/size register.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If an IN transfer is missed on isoc endpoint, then driver must insure
that next ep_queue is properly handled.
This patch fixes this issue by starting a new transfer for next queued
request.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
SOF Number is bit16:3 of DSTS. Correct the mask accordingly.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently in case of isoc, interrupt is programmed after each
TRB_NUM/4 ie 8th TRB. A TRB is programmed against each submitted
request from gadget. If we do not want to limit the minimum number of
necessary request to be submitted from gadget then we must receive
interrupt on each TRB submission. There can be such situation with a
gadget working with ping-pong buffer.
If a gadget does not want to receive interrupt after each request
completion then it may set no_interrupt flag.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
That's a much more intuitive name as that function
is only called at the completion of a Status Phase.
It also matches dwc3_ep0_complete_data() for
the completion of Data Phase.
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB is always little endian, but this driver
could run on non little endian cpus. Let's
be carefull with that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the databook, the DWC3 Core will
reset those bits to 0 on USB Bus Reset. This
means we must re-enable those bits on every
reset interrupt.
Because we will always get a Reset interrupt
after loading a gadget driver, we can, instead
of re-enabling something that was just lost,
move the handling of those bits to the Reset
Interrupt.
This patch fixes USB30CV U1/U2 Test.
Signed-off-by: Gerard CAUVY <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we don't read out the contents of the register
(in order to reinitialize 'reg' variable) we will
be writing unknown contents to the DCTL register
whenever we try to use dwc3_gadget_wakeup() function.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The same event buffers will be reused when coming
out of hibernation, so we must reinitialize them
properly to avoid any mistakes.
While at that, also take dwc3_event_buffers_setup()
out of __devinit section.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Recent cores (>= 1.94a) have a set of new features,
commands and a slightly different programming model.
This patch aims to support those changes.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
those two functions don't power PHYs, they simply
put them in suspend state. Rename to reflect better
what functions actually do.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds definitions for some new registers that have been
added to later versions of the controller, up to v2.10a.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On our Transfer Not Ready handlers, only
dwc3_ep0_do_control_status() had a different
list of parameters.
Align on the parameters in order to keep consistency.
No functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
IS_ALIGNED provides a much faster operation for
checking proper size alignment then a modulo
operation. Let's use it.
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When DWC3_EP_PENDING_REQUEST flag is set for a Control OUT Data
phase transfer, we would be missing the proper handling for
unaligned OUT requests, thus hanging a transfer.
Since proper handling is already done on dwc3_ep0_do_control_data(),
we simply re-factor that function so it can be re-used from
__dwc3_gadget_ep0_queue().
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we're now have DWC3_EP0_BOUNCE_SIZE to tell
us the actual size of the bufer. Let's use that
instead of ep0 wMaxPacketSize.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The warning shown up when ran with randconfig,
warning: (USB_DWC3) selects USB_XHCI_PLATFORM which has unmet direct dependencies (USB_SUPPORT && USB_XHCI_HCD)
Signed-off-by: joseph daniel <josephdanielwalter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.
We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.
Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.
Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qgf/
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.5 merge window
This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.
We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.
Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.
Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.
[ resolved conflicts and build error in drivers/usb/dwc3/gadget.c - gregkh]
to avoid sprinkling magic constants on the driver
we define a constant to be used when allocating
setup_buffer and ep0_bounce buffer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Issue an Update Transfer command after queuing a request to an isoc
EP with an active transfer. This is required according to the dwc3
databook. Pratyush Anand reports that this fixes a problem he was
having with Isoc IN transfers.
Tested-by: Pratyush Anand<pratyush.anand@st.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is basically a noop for DWC3. We don't have
to do anything. Basically we test if the request
parameters are correct, cache the Isochronous
Delay and return success.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We want to re-use that buffer for other USB
requests, so let's increase it to biggest
wMaxPacketSize for ep0 so it works for everything
we have in mind.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch implements Set SEL Standard Request
support for dwc3 driver. It needs to issue a command
to the controller passing the timing we received on
the data phase of the Set SEL request.
Signed-off-by: Felipe Balbi <balbi@ti.com>
On device loading the driver enables LPM and the acceptance of U1 and U2
states. The [Set|Clear]Feature requests for "U1/U2" are forwarded
directly to the hardware and allow / forbid the initiation of the low
power links.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This fix prevents a problem with dwc3 and host mode where
we were requesting the entire memory region in dwc3/core.c,
thus preventing xhci-plat from ever ioremapping its own address space.
Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We separate between dwc3-omap helper functions to dwc3-core helper
functions. This will allow us to change the helper functions
implementation according to each module need.
Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All revisions prior to 2.20a have a known issue which
causes metastability state on Run/Stop bit if we
configure the core to work on any of the USB2-only
speeds.
The suggested workaround is just to never configure the
core to anything other than SuperSpeed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We have other revisions already released, let's
define revision macros for those so we can do
runtime detection of known erratas.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Array should be freed together with event buffers, since it was
allocated dynamically.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without this default case returning an error,
thus replying with a stall, we would fail
USB30CV TD 9.11 Bad Feature test case.
Cc: stable@vger.kernel.org
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
due to a HW limitation we have a bounce buffer for ep0
out transfers which are not aligned with MaxPacketSize.
On such case we were not increment r->actual as we should.
This patch fixes that mistake.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
To allow ep0 out transfers of upto bounce buffer size
instead of maxpacketsize, use the transfer size as multiple
of ep0 maxpacket size.
Cc: stable@vger.kernel.org
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and other
various minor things.
There are some patches touching arch code, but they have all been acked
by the various arch maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9njL8ACgkQMUfUDdst+ylQ9wCfbBOnIT01lGOorkaE9pom0hhk
HfMAoKq1xzCR2B+OS3UMyUQffk+Ri9Ri
=KIQ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB merge for 3.4-rc1 from Greg KH:
"Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and
other various minor things.
There are some patches touching arch code, but they have all been
acked by the various arch maintainers."
* tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (302 commits)
net: qmi_wwan: add support for ZTE MF820D
USB: option: add ZTE MF820D
usb: gadget: f_fs: Remove lock is held before freeing checks
USB: option: make interface blacklist work again
usb/ub: deprecate & schedule for removal the "Low Performance USB Block" driver
USB: ohci-pxa27x: add clk_prepare/clk_unprepare calls
USB: use generic platform driver on ath79
USB: EHCI: Add a generic platform device driver
USB: OHCI: Add a generic platform device driver
USB: ftdi_sio: new PID: LUMEL PD12
USB: ftdi_sio: add support for FT-X series devices
USB: serial: mos7840: Fixed MCS7820 device attach problem
usb: Don't make USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.
usb gadget: fix a section mismatch when compiling g_ffs with CONFIG_USB_FUNCTIONFS_ETH
USB: ohci-nxp: Remove i2c_write(), use smbus
USB: ohci-nxp: Support for LPC32xx
USB: ohci-nxp: Rename symbols from pnx4008 to nxp
USB: OHCI-HCD: Rename ohci-pnx4008 to ohci-nxp
usb: gadget: Kconfig: fix typo for 'different'
usb: dwc3: pci: fix another failure path in dwc3_pci_probe()
...
When applying commit 7d26b58 (fix failure path in
dwc3_pci_probe()), I mistakenly left out one of the
possible failures where we would return success even
on the error case.
This patch fixes that mistake.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Z2+
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: changes for v3.4 merge window
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
Conflicts:
drivers/usb/dwc3/gadget.c
Transfer resource index is cleared in hardware when XFERCOMPLETE
event is generated, so clear the driver's res_trans_idx variable
immediately after that event is received. The upcoming hibernation
patches depend on this change.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_ep_set_wedge() and dwc3_gadget_set_selfpowered() were
modifying dwc->flags/dwc->is_selfpowered without taking the lock.
Since those modifications are non-atomic, that could cause other
flags to be corrupted. Fix them both to take the lock.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The loop in dwc3_gadget_set_link_state() was using a udelay(500),
which is a long time to delay in interrupt context. Change it to
udelay(5) and increase the loop count to match.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_pci_probe() would return success even if the calls to
dwc3_get_device_id() or platform_device_alloc() fail, fix that.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Define DWC3_GCTL_SCALEDOWN_MASK and use it in place of
DWC3_GCTL_SCALEDOWN(3).
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Zero is a valid value for a microframe number. So remove the bogus
test for non-zero in dwc3_gadget_start_isoc().
Cc: stable@vger.kernel.org
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's wrong to use the size of array as an argument for strncat.
Memory corruption is possible. strlcat is exactly what we need here.
Cc: stable@vger.kernel.org
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we have a non-ISOC endpoint, we will not have a Link TRB
pointing to the beginning of the TRB pool. On such endpoints,
we don't want to let the driver wrap around the TRB pool
otherwise controller will hang waiting for a valid TRB.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We always return zero instead of the id we found.
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/dwc3/core.c and drivers/usb/dwc3/dwc3-omap.c
included 'linux/module.h' twice, remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch enables to use devm_xxx functions during probing driver.
The devm_xxx series functions are able to release resource when the
driver is detatched. We can remove several codes to release resources
in the probe function.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds Exynos Specific Glue layer to support USB peripherals
on Samsung Exynos5 chips.
[ balbi@ti.com : prevent compilation of Exynos glue layer
on platforms which don't provide clk API implementation ]
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RR+f
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: Gadget: changes for 3.4
This merge is rather big. Here's what it contains:
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
Conflicts:
drivers/usb/dwc3/gadget.c
those routines have everything we need to map/unmap
USB requests and it's better to use them.
In order to achieve that, we had to add a simple
change on how we allocate and use our setup buffer;
we cannot allocate it from coherent anymore otherwise
the generic map/unmap routines won't be able to easily
know that the GetStatus request already has a DMA
address.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This fix a bug in f_serial, which expect the ep->desc to be NULL after
disabling an endpoint.
Cc: stable@vger.kernel.org
Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this will get rid of a useless memcpy on
IRQ handling, thus improving driver performance.
Tested with OMAP5430 running g_mass_storage on
SuperSpeed and HighSpeed.
Note that we are removing the little endian access
of the TRB and all accesses will be in System endianness,
if there happens to be a system in BE, bit 12 of GSBUSCFG0
should be set so that HW does byte invariant BE accesses
when fetching TRBs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When host requests us to enter a test mode,
we cannot directly enter the test mode before
Status Phase is completed, otherwise the core
will never be able to deliver the Status ZLP
to host, because it has already entered the
requested Test Mode.
In order to fix the error, we move the actual
start of Test Mode right after we receive
Transfer Complete event of the status phase.
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When implementing the USB2 testmode support via debugfs,
Felipe has committed a mistake when counting the number
of letters of some of the strings, resulting on an off
by one error which prevented some of the Test modes to
be entered properly.
This patch, fixes that mistake.
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This cuts down on the boilerplate code.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those transfer types are generally high bandwidth, so we
want to optimize transfers with those endpoints.
For that, databook suggests allocating 3 * wMaxPacketSize
of FIFO. Let's do that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
debugfs APIs will return NULL if it fails
to create the file/directory we ask it to
create.
Instead of checking for IS_ERR(ptr) we must
check for !ptr.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert our platform_data usage to OF property,
keep the legacy pdata for a while until the complete
conversion is done.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we set Run/Stop bit, we also move the
core to Rx.Detect state so that USB3 handshake
can start from a known location.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to dynamically re-size TxFifos for the
cases where default values will not do.
While at that, we create a simple function which,
for now, will just allocate one full packet fifo
space for each of the enabled endpoints.
This can be improved later in order to allow for
better throughput by allocating more space for
endpoints which could make good use of that like
isochronous and bulk.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass Storage gadget will take some time to handle
the SetConfiguration request, but even on those
cases we should move to CONFIGURED state.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Only bit 3 of the event status bitfield is valid
and the others should not be considered.
Make sure SW matches documentation on that case
to avoid bogus debugging prints which would
confuse an engineer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is very useful for low level link testing where
we might not have a USB Host stack, only a scope to
verify signal integrity.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Most link changes will, of course, happen with
the help of a matching host HW, but in some cases
we might want to debug very low level details about
the link and exposing this to debugfs sounds like
a good plan.
This is a preparation for such setup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is very useful for low level Link Testing where
we might not have a USB Host stack, only a scope to
verify signal integrity.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are some situations were we might need to
enable USB Test Modes without having access to a
Host stack. In such situations we cannot rely
solely on USB Control Messages to enable test
features.
For those cases, we will also allow test mode
to be enabled via debugfs and this patch is a
preparation for that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
num_sgs contains the number of sgs assigned by the gadget.
num_mapped_sgs contains the number of mapped sgs which may differ from
the gadget's values. For dma_unmap_sg() we have to provide the value
which was returned by dma_map_sg().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 34c60a7 (usb: dwc3: ep0: tidy up Pending
Request handling) introduced a compile warning
by leaving an unused variable.
This patch fixes that warning:
drivers/usb/dwc3/ep0.c: In function ‘__dwc3_gadget_ep0_queue’:
drivers/usb/dwc3/ep0.c:129:8: warning: unused variable ‘type’
[-Wunused-variable]
Signed-off-by: Felipe Balbi <balbi@ti.com>
The way our code was written, we should never have
a DWC3_EP_PENDING_REQUEST flag set out of a Data Phase
and the code in __dwc3_gadget_ep0_queue() did not
reflect that situation properly.
Tidy up that case to avoid any possible mistakes
when starting requests for IRQs which are long
gone.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Glue needs to be freed on exiting the function in an error case.
Furthermore, pci, which is the first argument to the probe function should
not be freed before leaveing the function, as it is reused at the call
site. So the free of pci is changed to free glue instead.
A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)
// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
x->f1
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to USB 3.0 Specification Table 9-22, if
bmAttributes [4:0] are set to zero, it means "no
streams supported", but the way this helper was
defined on Linux, we will *always* have one stream
which might cause several problems.
For example on DWC3, we would tell the controller
endpoint has streams enabled and yet start transfers
with Stream ID set to 0, which would goof up the host
side.
While doing that, convert the macro to an inline
function due to the different checks we now need.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
add support for SG lists on dwc3 driver. With
this we can e.g. use VFS layer's SG lists on
storage gadgets so that we can start bigger
transfers and improve throughput.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the LST bit is to be set on the last of a series
of consecutive TRBs. We had a workaround for a
problem where data would get corrupted but that
doesn't happen anymore. It's likely that it was
caused by some FPGA instability during development
phase.
Signed-off-by: Felipe Balbi <balbi@ti.com>
After a bus reset, we should move our state to
Default, in order to be able to re-enumerate again.
I only managed to trigger this problem with g_ether
by removing the cable after a few transfers had been
completed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
All our revision macros are defined with the entire
32-bits which we read from GSNPSID register, so we
must cache all 32-bits properly rather than masking
the top 16-bits.
This will fix all revision checks we have on current
driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a very small possibility (previously unimagined
by us) that the whole Mass Storage delayed status happens
rather early, before we even get our XferNotReady event.
In that case, we will be queueing a request to ep0 while
we're still on Setup Phase and we would be waiting for
another usb_ep_queue() forever.
Handle such cases by clearing dwc->delayed_status so that
we start control status from the next XferNotReady like
there was no wait for Delayed Status.
Tested against Linux 3.2-rc3 and USB30CV tool from USB-IF
(on a Windows XP with USB3 PCIe card).
Signed-off-by: Felipe Balbi <balbi@ti.com>
ep->max_streams is a mere hint to the gadget
driver that 'ep' supports stream handling. Using
that as a decision variable for enabling streams
was my worst brain-fart to date.
Instead, we should check from the Superspeed
Endpoint Companion Descriptor if the endpoint
has requested streams. For that we need a little
re-factoring but it is now correct.
Debugged-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
previous commit fixed part of it but it was still
calling usb_ep_queue() from IRQ context without
loosing locks. That cannot be done otherwise we will
have a recursive locking.
Also, we need to assign the 'dep' pointer on
dwc->ep0_usb_req otherwise we will have a NULL
pointer dereference on dwc3_map_buffer_to_dma().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of special functions and shortcuts for sending our internal
answers to the host we started doing what the gadget does and used the
public API for this. Since we only were using a few fields the
usb_request was enough. Later added the list handling in order to
synchronize the host / gadget events and now we require to have the
dwc3_request struct around our usb_request or else we touch memory that
does not belong to us. So this patch does this.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We mask the correct bits within the wrong register. The power
optimization mode is stored hwparam1 register and not in hwparam0.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
the new module_platform_driver macro is a helper
for modules which just register and unregister the
platform_driver. It allows us to delete a few
duplicated lines.
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 revisions <1.88a have an issue which would
case a missing Disconnect event if cable is
disconnected while there's a Setup packet
pending the FIFO.
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 revisions <1.90a have an issue which would cause
a missing USB3 Reset event. In such cases, it's
suggested that we follow the steps of a normal
USB3 Reset on Connection Done Event.
Signed-off-by: Felipe Balbi <balbi@ti.com>
RTL revisions <1.83a have an issue where, depending
on the link partner, the USB link might do multiple
entry/exit of low power states before a transfer
takes place causing degraded throughput.
The suggested workaround is to clear bits
12:9 of DCTL register if we see a transition
from U1|U2 to U0 and only re-enable that on
a transfer complete IRQ and we have no pending
transfers on any of the enabled endpoints.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch avoids the compiler spitting out the following warning:
|drivers/usb/dwc3/gadget.c:1304: warning: 'trb' is used uninitialized \
in this function
This is only uninitialized if the list of to-cleanup TRBs is empty which
should not be the case because we call this functions once a transfer
completed so it should be on list.
In order to make the warning disappear we return early. This should
never happen and the WARN_ON_ONCE(1) is there in case it happens
so we can investigate what went wrong.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the re-worked ep0 handling (which uses HW's hints to recognize the ep0
status) we lost the delayed status handling. This is used by the file and mass
storage gadget to gain some extra time so setup its internal status before it
can proceed further requests.
In particular the storage gadget does nothing on USB_REQ_SET_CONFIGURATION but
wakes up a thread which handles the request. If the udc driver continues ep0
handling before the thread did its work then then endpoint is not yet
configured and further requests will fail. Once the gadget is ready, it will
enqueue an empty packet which is used for synchronization.
In order to fix this issue, the patch does the following:
Set ->delayed_status once the delayed_status has been notices and do not
continue on the next XferNotReady event. We will continues ep0 processing once
the gadget enqueued the zero packet for synchronization.
A cleaner approach would be to enforce the gadget to enqueue an empty
(zero) request even for the status phase but this would do for now.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We wait for the XferNotReady before we start the transfer and by then we
know ep0 state in which we supposed to be.
This is some cleanup work for the following patch in which we require to
know the ep0 state before the transfer completes.
While here, also change the argument to dwc3_ep0_do_control_status() so
we don't require the complete event structure but only the required
piece of information.
Inspired-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
sparse caught three mistakes on this driver,
fix them:
drivers/usb/dwc3/ep0.c:806:29: warning: duplicate const
drivers/usb/dwc3/debugfs.c:481:15: warning: symbol 'dwc3_debugfs_init' \
was not declared. Should it be static?
drivers/usb/dwc3/debugfs.c:518:16: warning: symbol 'dwc3_debugfs_exit' \
was not declared. Should it be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were a few coding style issues with this driver
which are now fixed:
drivers/usb/dwc3/debugfs.c:48: WARNING: Use #include \
<linux/uaccess.h> instead of <asm/uaccess.h>
drivers/usb/dwc3/debugfs.c:484: ERROR: space required \
before the open brace '{'
drivers/usb/dwc3/ep0.c:261: WARNING: line over 80 characters
drivers/usb/dwc3/ep0.c:287: WARNING: suspect code indent \
for conditional statements (16, 23)
drivers/usb/dwc3/gadget.c:749: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.c:1267: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.h:116: WARNING: line over 80 characters
drivers/usb/dwc3/io.h:42: WARNING: Use #include \
<linux/io.h> instead of <asm/io.h>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A few inits like the scale value or the removal of the DISSCRAMBLE is
done in the gadget code however it touches a general register.
Move this piece to the core.c file since it is likely to be requied by
both, parts of the core (device and host).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are two where need to set operational mode:
- during initialization while we decide to run in host,device or DRD
mode
- at runtime via the debugfs interface.
This patch provides a new function which sets the operational mode and
moves its initialiation to the mode switch instead in the gadget code
itself.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In "usb: dwc3: remove special status request handling in ep0" I simplied
a few things and used the generic API for the status transfers. The bug
I introcuded here is that we queue now requests to dep[1] but we don't
clear that list in the stall+start case.
Actually we don't need to use dep[1] at all. We only did in the past to
talk to the correct endpoint (i.e. in or out). This is now take care of
in a diffent place within the ep0 code. So we could queue the in
transfers to dep[0] and don't use dep[1] at all.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The first access was correct, the second was wrong.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
hardware will tell us how many event buffers we
need to support, so let's allocate the array
dynamically too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we ever have an omap with multiple instances of
the DWC3 IP, we need unique names for them. In order
to achieve that, let's use the dwc3_get/put_device_id()
calls to give us an unique device identifier.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we want to support situations where we have
both SoC and PCIe versions of the IP on the same
platform, we need to have sequential numbers between
them, otherwise we will still have name collisions.
Because of that, we need to move dwc3_get/put_device_id()
to core.c and export that symbol to be used by glue
layers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The GetStatus (STD)-request is handled the driver and uses a tiny hack
to send the two bytes long answer. This patch removes the custom hack
uses the normal usb_ep_queue() for that.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we stall and restart we have to reset also this flag to 0 as there is
nothing pending anymore.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The read and write operation is atomic and we need no locking around
this operations. What we need however is a lock that is held which
ensures that the content of the DWC3_GCTL has not been changed. With
this, the conten may have been change changed after the first but before
our write back.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can have three modules here: dwc3.ko, dwc3-omap.ko and dwc3-pci.ko.
The later have already ids-aliases for probing and is fine. The omap
module has alias for DT but lacks alias for the "native"
platform_device. Maybe we should get rid of it and stick to the DT name?
Both glue modules create a new device for which the dwc3.ko module is
responsible and that one lacks the platform alias.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sometimes the host might be trying to initiate Data or
Status phase for an older Control transfer. In such
situations we must STALL that transfer and restart
the state machine rather than letting such situation
go through the wire.
Signed-off-by: Felipe Balbi <balbi@ti.com>
I have talked to USB-IF about USB30CV issuing SetAddres()
with a device on Configured state and they have agreed on
changing USB30CV not to do so.
Adding back the STALL reply in such case and while at
that, also add a debugging message for an address which
is too large.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Designware USB3 IP can be configured with
an internal xHCI. If we're running on such a
version, let's start the xHCI stack.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's no need to add driver_data for something
we can fetch from HW.
This also makes our id_table unnecessary - at least
for now -, so we also remove it on the same patch.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this is mainly for testing. In order to be able
to test if we're enumerating correctly on all
speeds, let that be controlled by a module
parameter.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit replaces usb_gadget's is_dualspeed field with
a max_speed field.
[ balbi@ti.com : Fixed DWC3 driver ]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
