Add junction temperature monitoring supervisor device driver, compatible
with the DA9062 and DA9061 PMICs. A MODULE_DEVICE_TABLE() macro is added.
If the PMIC's internal junction temperature rises above T_WARN (125 degC)
an interrupt is issued. This T_WARN level is defined as the
THERMAL_TRIP_HOT trip-wire inside the device driver.
The thermal triggering mechanism is interrupt based and happens when the
temperature rises above a given threshold level. The component cannot
return an exact temperature, it only has knowledge if the temperature is
above or below a given threshold value. A status bit must be polled to
detect when the temperature falls below that threshold level again. A
kernel work queue is configured to repeatedly poll and detect when the
temperature falls below this trip-wire, between 1 and 10 second intervals
(defaulting at 3 seconds).
This scheme is provided as an example. It would be expected that any
final implementation will also include a notify() function and any of these
settings could be altered to match the application where appropriate.
When over-temperature is reached, the interrupt from the DA9061/2 will be
repeatedly triggered. The IRQ is therefore disabled when the first
over-temperature event happens and the status bit is polled using a
work-queue until it becomes false.
This strategy is designed to allow the periodic transmission of uevents
(HOT trip point) as the first level of temperature supervision method. It
is intended for non-invasive temperature control, where the necessary
measures for cooling the system down are left to the host software. Once
the temperature falls again, the IRQ is re-enabled so a new critical
over-temperature event can be detected.
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Northstar is a SoC family commonly used in home routers. This commit
adds a driver for checking CPU temperature. As Northstar Plus seems to
also have this IP block this new symbol gets ARCH_BCM_IPROC dependency.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add basic thermal driver for bcm2835 SoC.
This driver currently make sure that tsense HW block is set up
correctly.
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
To restore operation it's easiest to reinitialise all TSCs. In order to
do this the current trip window needs to be stored in the TSC structure
so that it can be restored upon resume.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The device match data needs to be accessible outside the probe function,
store it in the private data structure.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Enable hardware trip points by implementing the set_trips callback. The
thermal core will take care of setting the initial trip point window and
to update it once the driver reports a TSC has moved outside it.
The interrupt structure for this device is a bit odd. There is not a
dedicated IRQ for each TSC, instead the interrupts are shared between
all TSCs. IRQn is fired if the temp monitored in IRQTEMPn is reached in
any of the TSCs, example IRQ3 is fired if temperature in IRQTEMP3 is
reached in either TSC0, TSC1 or TSC2.
For this reason the usage of interrupts in this driver is an all-on or
all-off design. When an interrupt happens all TSCs are checked and all
thermal zones are updated. This could be refined to be more fine grained
but the thermal core takes care of only updating the thermal zones that
have left their trip point window.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Record how many TSCs are found in struct rcar_gen3_thermal_priv, this is
needed to be able to add hardware interrupts for trip points later. Also
add a check to make sure at least one TSC is found.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Move the check for a TSC resource before allocating memory for a new
TSC. If no TSC is found there is little point in allocating memory for
it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no point in protecting a register read with a lock. This is
most likely a leftover from when the driver was reworked before being
submitted for upstream.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The .thermal_init needs to be delayed a short amount of time to allow
for the TEMP register to contain something useful. If it's not delayed
these warnings are common during boot:
thermal thermal_zone0: failed to read out thermal zone (-5)
thermal thermal_zone1: failed to read out thermal zone (-5)
thermal thermal_zone2: failed to read out thermal zone (-5)
The warnings are triggered by the first call to .get_temp() while the
TEMP register contains 0 and rcar_gen3_thermal_get_temp() returns -EIO
since a TEMP value of 0 will result in a temperature reading which is
out of specifications.
This should have been done in the initial commit which adds the driver
as the same issue was found and corrected for r8a7795.
Fixes: 564e73d283 ("thermal: rcar_gen3_thermal: Add R-Car Gen3 thermal driver")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
ti_thermal_expose_sensor always takes the
devm_thermal_zone_of_sensor_register call for registration
with the device tree nodes present for all the bandgap sensors
for omap3/4/5 and dra7 family. There are large chunks of unused
code. Removing all of them.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Now that slope and offset data are being passed from
device tree no need to populate in driver data.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently slope and offset values for calculating the hot spot
temperature of a thermal zone is being taken directly from driver
data. So fetch them from device tree.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The best place to register the CPU cooling device is from the cpufreq
driver as we would know if all the resources are already available or
not. That's what is done for the cpufreq-dt.c driver as well.
The cpu-cooling driver for dbx500 platform was just (un)registering
with the thermal framework and that can be handled easily by the cpufreq
driver as well and in proper sequence as well.
Get rid of the cooling driver and its its users and manage everything
from the cpufreq driver instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible for dev_pm_opp_find_freq_exact() to return errors. It was
all fine earlier as dev_pm_opp_get_voltage() had a check within it to
check for invalid OPPs, but dev_pm_opp_put() doesn't have any similar
checks and the callers need to make sure OPP is valid before calling
them.
Also update the later dev_warn_ratelimited() to not print the error
message as the OPP is guaranteed to be valid now.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There isn't much the user can do on seeing these warnings, as the
hardware is actually okay. dev_err suits much better here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
It is possible for dev_pm_opp_find_freq_exact() to return errors. It was
all fine earlier as dev_pm_opp_get_voltage() had a check within it to
check for invalid OPPs, but dev_pm_opp_put() doesn't have any similar
checks and the callers need to make sure OPP is valid before calling
them.
Also update the later dev_warn_ratelimited() to not print the error
message as the OPP is guaranteed to be valid now.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There isn't much the user can do on seeing this warning, as the hardware
is actually okay. dev_err suits much better here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There is no need to check for IS_ERR() as we are looking for a very
particular error value here. Drop the first check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
cooling_list_lock is covering not just cpufreq_dev_count, but also the
calls to cpufreq_register_notifier() and cpufreq_unregister_notifier().
Since cooling_list_lock is also used within cpufreq_thermal_notifier(),
lockdep reports a potential deadlock. Fix it by testing the condition
under cooling_list_lock and dropping the lock before calling
cpufreq_register_notifier(). And variable cpufreq_dev_count is removed
at the same time, because it's no longer needed after the fix.
Fixes: ae60608962 ("thermal: convert cpu_cooling to use an IDA")
Reported-and-Tested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We are going to move scheduler ABI details to <uapi/linux/sched/types.h>,
which will be used from a number of .c files.
Create empty placeholder header that maps to <linux/types.h>.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull thermal management updates from Zhang Rui:
- add thermal driver for R-Car Gen3 thermal sensors.
- add thermal driver for ZTE' zx2967 family thermal sensors.
- convert thermal ID allocation from IDR to IDA.
- fix a possible NULL dereference in imx thermal driver.
- fix a ti-soc-thermal driver dependency issue so that critical thermal
control is still available when CPU_THERMAL is not defined.
- update binding information for QorIQ thermal driver.
- a couple of cleanups in thermal core, intel_powerclamp, exynos,
dra752-thermal, mtk-thermal driver.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
powerpc/mpc85xx: Update TMU device tree node for T1023/T1024
powerpc/mpc85xx: Update TMU device tree node for T1040/T1042
dt-bindings: Update QorIQ TMU thermal bindings
thermal: mtk_thermal: Staticise a number of data variables
thermal: arm: dra752: Remove all TSHUT related definitions
thermal: arm: dra752: Remove TSHUT configuration
thermal: ti-soc-thermal: Remove CPU_THERMAL Dependency from TI_THERMAL
thermal: imx: Fix possible NULL dereference.
thermal: exynos: Remove parsing unused samsung,tmu_cal_mode property
thermal: zx2967: add thermal driver for ZTE's zx2967 family
thermal: use cpumask_var_t for on-stack cpu masks
dt: bindings: add documentation for zx2967 family thermal sensor
thermal/intel_powerclamp: Remove set-but-not-used variables
thermal: rcar_gen3_thermal: Add R-Car Gen3 thermal driver
thermal: rcar_gen3_thermal: Document the R-Car Gen3
thermal: convert devfreq_cooling to use an IDA
thermal: convert cpu_cooling to use an IDA
thermal: convert clock cooling to use an IDA
thermal core: convert ID allocation to IDA
* pm-opp: (24 commits)
PM / OPP: Expose _of_get_opp_desc_node as dev_pm_opp API
PM / OPP: Make _find_opp_table_unlocked() static
PM / OPP: Update Documentation to remove RCU specific bits
PM / OPP: Simplify dev_pm_opp_get_max_volt_latency()
PM / OPP: Simplify _opp_set_availability()
PM / OPP: Move away from RCU locking
PM / OPP: Take kref from _find_opp_table()
PM / OPP: Update OPP users to put reference
PM / OPP: Add 'struct kref' to struct dev_pm_opp
PM / OPP: Use dev_pm_opp_get_opp_table() instead of _add_opp_table()
PM / OPP: Take reference of the OPP table while adding/removing OPPs
PM / OPP: Return opp_table from dev_pm_opp_set_*() routines
PM / OPP: Add 'struct kref' to OPP table
PM / OPP: Add per OPP table mutex
PM / OPP: Split out part of _add_opp_table() and _remove_opp_table()
PM / OPP: Don't expose srcu_head to register notifiers
PM / OPP: Rename dev_pm_opp_get_suspend_opp() and return OPP rate
PM / OPP: Don't allocate OPP table from _opp_allocate()
PM / OPP: Rename and split _dev_pm_opp_remove_table()
PM / OPP: Add light weight _opp_free() routine
...
Sparse throws following warnings:
drivers/thermal/mtk_thermal.c:186:11: warning: symbol 'mt8173_bank_data' was not declared. Should it be static?
drivers/thermal/mtk_thermal.c:193:11: warning: symbol 'mt8173_msr' was not declared. Should it be static?
drivers/thermal/mtk_thermal.c:197:11: warning: symbol 'mt8173_adcpnp' was not declared. Should it be static?
drivers/thermal/mtk_thermal.c:201:11: warning: symbol 'mt8173_mux_values' was not declared. Should it be static?
drivers/thermal/mtk_thermal.c:204:11: warning: symbol 'mt2701_bank_data' was not declared. Should it be static?
drivers/thermal/mtk_thermal.c:208:11: warning: symbol 'mt2701_msr' was not declared. Should it be static?
drivers/thermal/mtk_thermal.c:212:11: warning: symbol 'mt2701_adcpnp' was not declared. Should it be static?
drivers/thermal/mtk_thermal.c:216:11: warning: symbol 'mt2701_mux_values' was not declared. Should it be static?
Make these variables as static to fix these warnings.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
No configuration needs to be done for TSHUT from software.
Hence remove all the unnecessary definitions.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently when CPU_THERMAL is not defined the thermal sensors
are not even exposed consequently no cooling is possible. CPU_THERMAL
eventually depends on CPUFREQ. CPPUFREQ is not the only cooling
for CPU.
The thermal shutdown for critical temperatures is another
cooling solution which will currently not get enabled if CPU_THERMAL
is not defined. Remove this dependency so as to have the last level
of thermal protection working even without CPUFREQ defined.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
of_device_get_match_data could return NULL, and so can cause
a NULL pointer dereference later.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The property samsung,tmu_cal_mode is not used and not used. We can
safely remove it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Putting a bare cpumask structure on the stack produces a warning on
large SMP configurations:
drivers/thermal/cpu_cooling.c: In function 'cpufreq_state2power':
drivers/thermal/cpu_cooling.c:644:1: warning: the frame size of 1056 bytes is larger than 1024 bytes [-Wframe-larger-than=]
drivers/thermal/cpu_cooling.c: In function '__cpufreq_cooling_register':
drivers/thermal/cpu_cooling.c:898:1: warning: the frame size of 1104 bytes is larger than 1024 bytes [-Wframe-larger-than=]
The recommended workaround is to use cpumask_var_t, which behaves just like
a normal cpu mask in most cases, but turns into a dynamic allocation
when CONFIG_CPUMASK_OFFSTACK is set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In poll_pkg_cstate() function, the variables jiffies_last and
jiffies_now are set but never used.
This has been detected by building the driver with W=1:
drivers/thermal/intel_powerclamp.c: In function ‘poll_pkg_cstate’:
drivers/thermal/intel_powerclamp.c:464:23: warning: variable
‘jiffies_last’ set but not used [-Wunused-but-set-variable]
static unsigned long jiffies_last;
^
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch updates dev_pm_opp_find_freq_*() routines to get a reference
to the OPPs returned by them.
Also updates the users of dev_pm_opp_find_freq_*() routines to call
dev_pm_opp_put() after they are done using the OPPs.
As it is guaranteed the that OPPs wouldn't get freed while being used,
the RCU read side locking present with the users isn't required anymore.
Drop it as well.
This patch also updates all users of devfreq_recommended_opp() which was
returning an OPP received from the OPP core.
Note that some of the OPP core routines have gained
rcu_read_{lock|unlock}() calls, as those still use RCU specific APIs
within them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> [Devfreq]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 7611fb6806 ("thermal: thermal_hwmon: Convert to
hwmon_device_register_with_info()").
Pavel Machek reported breakage in the Nokia N900 due to this commit.
We can revisit a proper fix for the warning later.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add support for R-Car Gen3 thermal sensors. Polling only for now,
interrupts will be added incrementally. Same goes for reading fuses.
This is documented already, but no hardware available for now.
Signed-off-by: Hien Dang <hien.dang.eb@renesas.com>
Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com>
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[Niklas: document and rework temperature calculation]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As Ayaka reported the thermal was abormal on rk3288 at booting time.
thermal thermal_zone1: critical temperature reached(125 C),shutting down
thermal thermal_zone2: critical temperature reached(125 C),shutting down
thermal thermal_zone1: critical temperature reached(125 C),shutting down
thermal thermal_zone2: critical temperature reached(125 C),shutting down
...
The root caused by reading the invald analogic value, the value is zero
will convert the 125 degree to trigger the critical temperature.
Fixes it with insteading of the incorrect reading now.
Fixes commit cadf29dc2a
("thermal: rockchip: optimize the conversion table")
Reported-by: ayaka <ayaka@soulik.info>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The device_unregister call in thermal_zone_device_unregister causes the
thermal_zone_device structure to be freed before the call to free the
dynamically allocated attribute groups. This leads to a kernel panic.
Furthermore, the 4 calls to free the trip point attribute structures
occur before the call to unregister the device, leading to a kernel
panic when sysfs attempts to access the attributes to remove them.
Here is an example of a kernel panic when the cpu thermal zones are
removed upon cpu offline:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: strlen+0x0/0x20
<snip>
Call Trace:
? kernfs_name_hash+0x17/0x80
kernfs_find_ns+0x3f/0xd0
kernfs_remove_by_name_ns+0x36/0xa0
remove_files.isra.1+0x36/0x70
sysfs_remove_group+0x44/0x90
sysfs_remove_groups+0x2e/0x50
device_remove_attrs+0x5e/0x90
device_del+0x1ea/0x350
device_unregister+0x1a/0x60
thermal_zone_device_unregister+0x1f2/0x210
pkg_thermal_cpu_offline+0x14f/0x1a0 [x86_pkg_temp_thermal]
? kzalloc.constprop.2+0x10/0x10 [x86_pkg_temp_thermal]
cpuhp_invoke_callback+0x8d/0x3f0
cpuhp_down_callbacks+0x42/0x80
cpuhp_thread_fun+0x8b/0xf0
smpboot_thread_fn+0x110/0x160
kthread+0x101/0x140
? sort_range+0x30/0x30
? kthread_park+0x90/0x90
ret_from_fork+0x25/0x30
This patch moves the kfree calls to clean up the dynamic attributes to
the thermal_class's thermal_zone_device release function.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Jacob von Chorus <jacobvonchorus@cwphoto.ca>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
thermal devfreq cooling does not use the ability to look up pointers by
ID, so convert it from using an IDR to the more space-efficient IDA.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
thermal cpu cooling does not use the ability to look up pointers by ID,
so convert it from using an IDR to the more space-efficient IDA.
The cooling_cpufreq_lock was being used to protect cpufreq_dev_count as
well as the IDR. Rather than keep the mutex to protect a single integer,
I expanded the scope of cooling_list_lock to also cover cpufreq_dev_count.
We could also convert cpufreq_dev_count into an atomic.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
thermal clock cooling does not use the ability to look up pointers by ID,
so convert it from using an IDR to the more space-efficient IDA.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The thermal core does not use the ability to look up pointers by ID, so
convert it from using an IDR to the more space-efficient IDA.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Booting Linux on a mx6q based board leads to the following warning:
(NULL device *): hwmon_device_register() is deprecated. Please convert the
driver to use hwmon_device_register_with_info().
,so do as suggested.
Also, this results in the core taking care of creating the 'name'
attribute, so drop the code doing that from the thermal driver.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In some cases, some sensors didn't need the trip points, the
set_trips will pass {-INT_MAX, INT_MAX} to trigger tsadc alarm in the end,
ignore this case and disable the high temperature interrupt.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In order to support the valid temperature can conver to analog value.
The rockchip thermal driver has not supported the all valid temperature
to convert the analog value. (e.g.: 61C, 62C, 63C....)
For example:
In some cases, we need adjust the trip point.
$cd /sys/class/thermal/thermal_zone*
$echo 68000 > trip_point_0_temp
That will return the max analogic value indicates the invalid before
posting this patch.
So, this patch will optimize the conversion table to support the other
cases.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The temp_to_code function will return 0 when we set the temperature to a
invalid value (e.g. 61C, 62C, 63C....), that's unpractical. This patch
will prevent this case happening. That will return the max analog value to
indicate the temperature is invalid or over table temperature range.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This driver passes struct chip_tsadc_table by value throughout; this is
inefficient, and AFAICT, there is no reason for it. Let's pass pointers
instead.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
These error messages don't give much information about what went wrong.
It would be nice, for one, to see what invalid temperature was being
requested when conversion fails. It's also good to return an error when
we can't handle a conversion properly.
While we're at it, fix the grammar too.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
- New cpufreq driver for Broadcom STB SoCs and a Device Tree binding
for it (Markus Mayer).
- Support for ARM Integrator/AP and Integrator/CP in the generic
DT cpufreq driver and elimination of the old Integrator cpufreq
driver (Linus Walleij).
- Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier,
and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie,
Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik).
- cpufreq core fix to eliminate races that may lead to using
inactive policy objects and related cleanups (Rafael Wysocki).
- cpufreq schedutil governor update to make it use SCHED_FIFO
kernel threads (instead of regular workqueues) for doing delayed
work (to reduce the response latency in some cases) and related
cleanups (Viresh Kumar).
- New cpufreq sysfs attribute for resetting statistics (Markus
Mayer).
- cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis,
Viresh Kumar).
- Support for using generic cpufreq governors in the intel_pstate
driver (Rafael Wysocki).
- Support for per-logical-CPU P-state limits and the EPP/EPB
(Energy Performance Preference/Energy Performance Bias) knobs
in the intel_pstate driver (Srinivas Pandruvada).
- New CPU ID for Knights Mill in intel_pstate (Piotr Luc).
- intel_pstate driver modification to use the P-state selection
algorithm based on CPU load on platforms with the system profile
in the ACPI tables set to "mobile" (Srinivas Pandruvada).
- intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki,
Srinivas Pandruvada).
- cpufreq powernv driver updates including fast switching support
(for the schedutil governor), fixes and cleanus (Akshay Adiga,
Andrew Donnellan, Denis Kirjanov).
- acpi-cpufreq driver rework to switch it over to the new CPU
offline/online state machine (Sebastian Andrzej Siewior).
- Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth
Prakash).
- Idle injection rework (to make it use the regular idle path
instead of a home-grown custom one) and related powerclamp
thermal driver updates (Peter Zijlstra, Jacob Pan, Petr Mladek,
Sebastian Andrzej Siewior).
- New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy
Shevchenko, Piotr Luc).
- intel_idle driver cleanups and switch over to using the new CPU
offline/online state machine (Anna-Maria Gleixner, Sebastian
Andrzej Siewior).
- cpuidle DT driver update to support suspend-to-idle properly
(Sudeep Holla).
- cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian,
Rafael Wysocki).
- Preliminary support for power domains including CPUs in the
generic power domains (genpd) framework and related DT bindings
(Lina Iyer).
- Assorted fixes and cleanups in the generic power domains (genpd)
framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven).
- Preliminary support for devices with multiple voltage regulators
and related fixes and cleanups in the Operating Performance Points
(OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd).
- System sleep state selection interface rework to make it easier
to support suspend-to-idle as the default system suspend method
(Rafael Wysocki).
- PM core fixes and cleanups, mostly related to the interactions
between the system suspend and runtime PM frameworks (Ulf Hansson,
Sahitya Tummala, Tony Lindgren).
- Latency tolerance PM QoS framework imorovements (Andrew
Lutomirski).
- New Knights Mill CPU ID for the Intel RAPL power capping driver
(Piotr Luc).
- Intel RAPL power capping driver fixes, cleanups and switch over
to using the new CPU offline/online state machine (Jacob Pan,
Thomas Gleixner, Sebastian Andrzej Siewior).
- Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc,
rockchip-dfi devfreq drivers and the devfreq core (Axel Lin,
Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh
Kumar).
- Fix for false-positive KASAN warnings during resume from ACPI S3
(suspend-to-RAM) on x86 (Josh Poimboeuf).
- Memory map verification during resume from hibernation on x86 to
ensure a consistent address space layout (Chen Yu).
- Wakeup sources debugging enhancement (Xing Wei).
- rockchip-io AVS driver cleanup (Shawn Lin).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vhxI
-----END PGP SIGNATURE-----
Merge tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Again, cpufreq gets more changes than the other parts this time (one
new driver, one old driver less, a bunch of enhancements of the
existing code, new CPU IDs, fixes, cleanups)
There also are some changes in cpuidle (idle injection rework, a
couple of new CPU IDs, online/offline rework in intel_idle, fixes and
cleanups), in the generic power domains framework (mostly related to
supporting power domains containing CPUs), and in the Operating
Performance Points (OPP) library (mostly related to supporting devices
with multiple voltage regulators)
In addition to that, the system sleep state selection interface is
modified to make it easier for distributions with unchanged user space
to support suspend-to-idle as the default system suspend method, some
issues are fixed in the PM core, the latency tolerance PM QoS
framework is improved a bit, the Intel RAPL power capping driver is
cleaned up and there are some fixes and cleanups in the devfreq
subsystem
Specifics:
- New cpufreq driver for Broadcom STB SoCs and a Device Tree binding
for it (Markus Mayer)
- Support for ARM Integrator/AP and Integrator/CP in the generic DT
cpufreq driver and elimination of the old Integrator cpufreq driver
(Linus Walleij)
- Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier,
and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie,
Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik)
- cpufreq core fix to eliminate races that may lead to using inactive
policy objects and related cleanups (Rafael Wysocki)
- cpufreq schedutil governor update to make it use SCHED_FIFO kernel
threads (instead of regular workqueues) for doing delayed work (to
reduce the response latency in some cases) and related cleanups
(Viresh Kumar)
- New cpufreq sysfs attribute for resetting statistics (Markus Mayer)
- cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis,
Viresh Kumar)
- Support for using generic cpufreq governors in the intel_pstate
driver (Rafael Wysocki)
- Support for per-logical-CPU P-state limits and the EPP/EPB (Energy
Performance Preference/Energy Performance Bias) knobs in the
intel_pstate driver (Srinivas Pandruvada)
- New CPU ID for Knights Mill in intel_pstate (Piotr Luc)
- intel_pstate driver modification to use the P-state selection
algorithm based on CPU load on platforms with the system profile in
the ACPI tables set to "mobile" (Srinivas Pandruvada)
- intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki,
Srinivas Pandruvada)
- cpufreq powernv driver updates including fast switching support
(for the schedutil governor), fixes and cleanus (Akshay Adiga,
Andrew Donnellan, Denis Kirjanov)
- acpi-cpufreq driver rework to switch it over to the new CPU
offline/online state machine (Sebastian Andrzej Siewior)
- Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth
Prakash)
- Idle injection rework (to make it use the regular idle path instead
of a home-grown custom one) and related powerclamp thermal driver
updates (Peter Zijlstra, Jacob Pan, Petr Mladek, Sebastian Andrzej
Siewior)
- New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy
Shevchenko, Piotr Luc)
- intel_idle driver cleanups and switch over to using the new CPU
offline/online state machine (Anna-Maria Gleixner, Sebastian
Andrzej Siewior)
- cpuidle DT driver update to support suspend-to-idle properly
(Sudeep Holla)
- cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian,
Rafael Wysocki)
- Preliminary support for power domains including CPUs in the generic
power domains (genpd) framework and related DT bindings (Lina Iyer)
- Assorted fixes and cleanups in the generic power domains (genpd)
framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven)
- Preliminary support for devices with multiple voltage regulators
and related fixes and cleanups in the Operating Performance Points
(OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd)
- System sleep state selection interface rework to make it easier to
support suspend-to-idle as the default system suspend method
(Rafael Wysocki)
- PM core fixes and cleanups, mostly related to the interactions
between the system suspend and runtime PM frameworks (Ulf Hansson,
Sahitya Tummala, Tony Lindgren)
- Latency tolerance PM QoS framework imorovements (Andrew Lutomirski)
- New Knights Mill CPU ID for the Intel RAPL power capping driver
(Piotr Luc)
- Intel RAPL power capping driver fixes, cleanups and switch over to
using the new CPU offline/online state machine (Jacob Pan, Thomas
Gleixner, Sebastian Andrzej Siewior)
- Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc,
rockchip-dfi devfreq drivers and the devfreq core (Axel Lin,
Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh Kumar)
- Fix for false-positive KASAN warnings during resume from ACPI S3
(suspend-to-RAM) on x86 (Josh Poimboeuf)
- Memory map verification during resume from hibernation on x86 to
ensure a consistent address space layout (Chen Yu)
- Wakeup sources debugging enhancement (Xing Wei)
- rockchip-io AVS driver cleanup (Shawn Lin)"
* tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (127 commits)
devfreq: rk3399_dmc: Don't use OPP structures outside of RCU locks
devfreq: rk3399_dmc: Remove dangling rcu_read_unlock()
devfreq: exynos: Don't use OPP structures outside of RCU locks
Documentation: intel_pstate: Document HWP energy/performance hints
cpufreq: intel_pstate: Support for energy performance hints with HWP
cpufreq: intel_pstate: Add locking around HWP requests
PM / sleep: Print active wakeup sources when blocking on wakeup_count reads
PM / core: Fix bug in the error handling of async suspend
PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend
PM / Domains: Fix compatible for domain idle state
PM / OPP: Don't WARN on multiple calls to dev_pm_opp_set_regulators()
PM / OPP: Allow platform specific custom set_opp() callbacks
PM / OPP: Separate out _generic_set_opp()
PM / OPP: Add infrastructure to manage multiple regulators
PM / OPP: Pass struct dev_pm_opp_supply to _set_opp_voltage()
PM / OPP: Manage supply's voltage/current in a separate structure
PM / OPP: Don't use OPP structure outside of rcu protected section
PM / OPP: Reword binding supporting multiple regulators per device
PM / OPP: Fix incorrect cpu-supply property in binding
cpuidle: Add a kerneldoc comment to cpuidle_use_deepest_state()
..
Pull thermal management updates from Zhang Rui:
- Thermal core code reorganization and cleanup. Two new files are
created for thermal sysfs I/F code and thermal helper functions
(Eduardo Valentin).
- Sanitize hotplug and locking for x86_pkg_temp driver (Thomas
Gleixner)
- Update MAINTAINER file for pwm-fan driver and Samsung thermal driver
(Lukasz Majewski)
- Fix module auto-load for max77620, tango and db8500 thermal driver
(Javier Martinez Canillas)
- Fix a bug that thermal hwmon sysfs I/F returns wrong critical trip
point temperature value (Krzysztof Kozlowski)
- Add Skylake PCH 100 series support for intel_pch_thermal driver
(OGAWA Hirofumi)
- Small fixes and cleanups for platform thermal drivers (Julia Lawall,
Luis Henriques, Leo Yan, Stephen Boyd, Shawn Lin, Javi Merino and
Lukasz Luba)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (76 commits)
MAINTAINERS: Samsung: Update maintainer for PWM FAN and SAMSUNG THERMAL
thermal/x86 pkg temp: Convert to hotplug state machine
thermal/x86_pkg_temp: Sanitize package management
thermal/x86_pkg_temp: Move work into package struct
thermal/x86_pkg_temp: Move work scheduled flag into package struct
thermal/x86_pkg_temp: Sanitize locking
thermal/x86_pkg_temp: Cleanup code some more
thermal/x86_pkg_temp: Cleanup namespace
thermal/x86_pkg_temp: Get rid of ref counting
thermal/x86_pkg_temp: Sanitize callback (de)initialization
thermal/x86_pkg_temp: Replace open coded cpu search
thermal/x86_pkg_temp: Remove redundant package search
thermal/x86_pkg_temp: Cleanup thermal interrupt handling
thermal: hwmon: Properly report critical temperature in sysfs
devfreq_cooling: pass a pointer to devfreq in the power model callbacks
devfreq_cooling: make the structs devfreq_cooling_xxx visible for all
dt-bindings: rockchip-thermal: fix the misleading description
thermal: rockchip: improve the warning log
thermal: db8500: Fix module autoload
thermal: tango: Fix module autoload
...
Pull x86 idle updates from Ingo Molnar:
"There were two bigger changes in this development cycle:
- remove idle notifiers:
32 files changed, 74 insertions(+), 803 deletions(-)
These notifiers were of questionable value and the main usecase,
the i7300 driver, was essentially unmaintained and can be removed,
plus modern power management concepts don't need the callback - so
use this golden opportunity and get rid of this opaque and fragile
callback from a latency sensitive code path.
(Len Brown, Thomas Gleixner)
- improve the AMD Erratum 400 workaround that used high overhead MSR
polling in the idle loop (Borisla Petkov, Thomas Gleixner)"
* 'x86-idle-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove empty idle.h header
x86/amd: Simplify AMD E400 aware idle routine
x86/amd: Check for the C1E bug post ACPI subsystem init
x86/bugs: Separate AMD E400 erratum and C1E bug
x86/cpufeature: Provide helper to set bugs bits
x86/idle: Remove enter_idle(), exit_idle()
x86: Remove x86_test_and_clear_bit_percpu()
x86/idle: Remove is_idle flag
x86/idle: Remove idle_notifier
i7300_idle: Remove this driver
One include less is always a good thing(tm). Good riddance.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-6-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Replace the wrmsr/rdmrs_on_cpu() calls in the hotplug callbacks as they are
guaranteed to be invoked on the incoming/outgoing cpu.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Packages are kept in a list, which must be searched over and over.
We can be smarter than that and just store the package pointers in an array
which is allocated at init time. Sizing of the array is determined from the
topology information. That makes the package search a simple array lookup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Delayed work structs are held in a static percpu storage, which makes no
sense at all because work is strictly per package and we never schedule
more than one work per package.
Aside of that the work cancelation in the hotplug is broken when the work
is queued on the outgoing cpu and canceled. Nothing reschedules the work on
another online cpu in the package, so the interrupts stay disabled and the
work_scheduled flag stays active.
Move the delayed work struct into the package struct, which is the only
sensible place to have it.
To simplify the cancelation logic schedule the work always on the cpu which
is the target for the sysfs files. This is required so the cancelation
logic in the cpu offline path cancels only when the outgoing cpu is the
current target and reschedule the work when there is still a online
CPU in the package.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Storage for a boolean information whether work is scheduled for a package
is kept in separate allocated storage, which is resized when the number of
detected packages grows.
With the proper locking in place this is a completely pointless exercise
because we can simply stick it into the per package struct.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The work cancellation code, the thermal zone unregistering, the work code
and the interrupt notification function are racy against each other and
against cpu hotplug and module exit. The random locking sprinkeled all
over the place does not help anything and probably exists to make people
feel good. The resulting issues (mainly use after free) are probably
hard to trigger, but they clearly exist
Protect the package list with a spinlock so it can be accessed from the
interrupt notifier and also from the work function. The add/removal code in
the hotplug callbacks take the lock for list manipulation. That makes sure
that on removal neither the interrupt notifier nor the work function can
access the about to be freed package structure anymore.
The thermal zone unregistering is another trainwreck. It's not serialized
against the work function. So unregistering the zone device can race with
the work function and cause havoc.
Protect the thermal zone with a mutex, which is held in the work
function to make sure that the zone device is not being unregistered
concurrently.
To solve the module exit issues, we simply invoke the cpu offline callback
and let it work its magic. For that it's required to keep track of the
participating cpus in a package, because topology_core_mask is not affected
by calling the offline callback for teardown of the driver, so it would
never free the package as there is always a valid target in
topology_core_mask.
Use proper names for the locks so it's clear what they are for and add a
pile of comments to explain the protection rules.
It's amazing that fixing the locking and adding 30 lines of comments
explaining it still removes more lines than it adds.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Coding style fixups and replacement of overly complex constructs and random
error codes instead of returning the real ones. This mess makes the eyes bleeding.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Any randomly chosen struct name is more descriptive than phy_dev_entry.
Rename the whole thing to struct pkg_device, which describes the content
reasonably well and use the same variable name throughout the code so it
gets readable. Rename the msr struct members as well.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There is no point in the whole package data refcounting dance because
topology_core_cpumask tells us whether this is the last cpu in the
package. If yes, then the package can go, if not it stays. It's already
serialized via the hotplug code.
While at it rename the first_cpu member of the package structure to
cpu. The first has absolutely no meaning.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The threshold callbacks are installed before the initialization of the
online cpus has succeeded and removed after the teardown has been
done. That's both wrong as callbacks might be invoked into a half
initialized or torn down state.
Move them to the proper places: Last in init() and first in exit().
While at it shorten the insane long and horrible named function names.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
find_next_sibling() iterates over the online cpus and searches for a cpu
with the same package id as the current cpu. This is a pointless exercise
as topology_core_cpumask() allows a simple cpumask search for an online cpu
on the same package.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In pkg_temp_thermal_device_remove() the package device is searched at the
beginning of the function. When the device refcount becomes zero another
search for the same device is conducted. Remove the pointless loop and use
the device pointer which was retrieved at the beginning of the function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Wenn a package is removed nothing restores the thermal interrupt MSR so
the content will be stale when a CPU of that package becomes online again.
Aside of that the work function reenables interrupts before acknowledging
the current one, which is the wrong order to begin with.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In the critical sysfs entry the thermal hwmon was returning wrong
temperature to the user-space. It was reporting the temperature of the
first trip point instead of the temperature of critical trip point.
For example:
/sys/class/hwmon/hwmon0/temp1_crit:50000
/sys/class/thermal/thermal_zone0/trip_point_0_temp:50000
/sys/class/thermal/thermal_zone0/trip_point_0_type:active
/sys/class/thermal/thermal_zone0/trip_point_3_temp:120000
/sys/class/thermal/thermal_zone0/trip_point_3_type:critical
Since commit e68b16abd9 ("thermal: add hwmon sysfs I/F") the driver
have been registering a sysfs entry if get_crit_temp() callback was
provided. However when accessed, it was calling get_trip_temp() instead
of the get_crit_temp().
Fixes: e68b16abd9 ("thermal: add hwmon sysfs I/F")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
With the introduction of play_idle(), idle injection kthread can
go through the normal idle task processing to get correct accounting
and turn off scheduler tick when possible.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a conversation to the new hotplug state machine with
the difference that CPU_DEAD becomes CPU_PREDOWN.
At the same time it makes the handling of the two states symmetrical.
stop_power_clamp_worker() is called unconditionally and the controversial
error message is removed.
Finally, the hotplug state callbacks are removed after the powerclamping
is stopped to avoid a potential race.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[pmladek@suse.com: Fixed the possible race in powerclamp_exit()]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Kthreads are currently implemented as an infinite loop. Each
has its own variant of checks for terminating, freezing,
awakening. In many cases it is unclear to say in which state
it is and sometimes it is done a wrong way.
The plan is to convert kthreads into kthread_worker or workqueues
API. It allows to split the functionality into separate operations.
It helps to make a better structure. Also it defines a clean state
where no locks are taken, IRQs blocked, the kthread might sleep
or even be safely migrated.
The kthread worker API is useful when we want to have a dedicated
single thread for the work. It helps to make sure that it is
available when needed. Also it allows a better control, e.g.
define a scheduling priority.
This patch converts the intel powerclamp kthreads into the kthread
worker because they need to have a good control over the assigned
CPUs.
IMHO, the most natural way is to split one cycle into two works.
First one does some balancing and let the CPU work normal
way for some time. The second work checks what the CPU has done
in the meantime and put it into C-state to reach the required
idle time ratio. The delay between the two works is achieved
by the delayed kthread work.
The two works have to share some data that used to be local
variables of the single kthread function. This is achieved
by the new per-CPU struct kthread_worker_data. It might look
as a complication. On the other hand, the long original kthread
function was not nice either.
The patch tries to avoid extra init and cleanup works. All the
actions might be done outside the thread. They are moved
to the functions that create or destroy the worker. Especially,
I checked that the timers are assigned to the right CPU.
The two works are queuing each other. It makes it a bit tricky to
break it when we want to stop the worker. We use the global and
per-worker "clamping" variables to make sure that the re-queuing
eventually stops. We also cancel the works to make it faster.
Note that the canceling is not reliable because the handling
of the two variables and queuing is not synchronized via a lock.
But it is not a big deal because it is just an optimization.
The job is stopped faster than before in most cases.
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch removes code duplication. It does not modify
the functionality.
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the devfreq cooling device was designed, it was an oversight not to
pass a pointer to the struct devfreq as the first parameters of the
callbacks. The design patterns of the kernel suggest it for a good
reason.
By passing a pointer to struct devfreq, the driver can register one
function that works with multiple devices. With the current
implementation, a driver that can work with multiple devices has to
create multiple copies of the same function with different parameters so
that each devfreq_cooling_device can use the appropriate one. By
passing a pointer to struct devfreq, the driver can identify which
device it's referring to.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Ørjan Eide <orjan.eide@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It is no necessary to print warning agian and again if we don't
add rockchip,grf for dt, otherwise I saw the following log when
doing suspend-2-resume. We only need to print it once when parsing
dt. It looks quite trivial but the log is apparently verbose.
[ 26.615415] PM: early resume of devices complete after 1.539 msecs
[ 26.622002] rk_tsadcv2_initialize: Missing rockchip,grf property
[ 26.629359] rk_gmac-dwmac ff290000.ethernet: init for RGMII
[ 26.639794] PM: resume of devices complete after 18.109 msecs
[ 26.646925] Restarting tasks ... done.
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/thermal/db8500_thermal.ko | grep alias
$
After this patch:
$ modinfo drivers/thermal/db8500_thermal.ko | grep alias
alias: of:N*T*Cstericsson,db8500-thermalC*
alias: of:N*T*Cstericsson,db8500-thermal
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/thermal/tango_thermal.ko | grep alias
$
After this patch:
$ modinfo drivers/thermal/tango_thermal.ko | grep alias
alias: of:N*T*Csigma,smp8758-thermalC*
alias: of:N*T*Csigma,smp8758-thermal
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/thermal/max77620_thermal.ko | grep alias
$
After this patch:
$ modinfo drivers/thermal/max77620_thermal.ko | grep alias
alias: platform:max77620-thermal
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We only read the first element of the reg property to figure out
the offset of the temperature sensor inside the PMIC.
Furthermore, we want to remove the second element in DT, so just
don't read the second element so that probe keeps working if we
change the DT in the future.
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal driver is standalone driver which is used to enable
thermal sensors, so it can be used with any cooling device and
should not bind with CPU cooling device driver.
This original patch is suggested by Amit Kucheria; so it's to
polish the dependency in Kconfig, and remove the dependency with
CPU_THERMAL.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch fixes the following Coccinelle error:
./drivers/thermal/ti-soc-thermal/ti-bandgap.c:1441:1-7: \
ERROR: missing clk_put; clk_get on line 1290 \
and execution via conditional on line 1298
Signed-off-by: Luis Henriques <henrix@camandro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As a safety check, this patch changes thermal
core to check for pointer content size, instead of type size,
while allocating memory.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pass through the code to remove check suggested by
checkpatch.pl (alignment to parenthesis):
CHECK: Alignment should match open parenthesis
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Simplify the GPL notice by removing the FSF address.
No need to track FSF location in this file.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Remove the following warning:
In file included from drivers/thermal/thermal_sysfs.c:19:0:
include/linux/device.h:575:26: warning: ‘dev_attr_emul_temp’ defined but not used [-Wunused-variable]
struct device_attribute dev_attr_##_name = __ATTR(_name, _mode, _show, _store)
^
drivers/thermal/thermal_sysfs.c:395:8: note: in expansion of macro ‘DEVICE_ATTR’
when emul temp is disabled at Kconfig.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Simply marking the power actor section and adding a
comment describing it.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
moving the helper function to closer to similar functions.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Moving the helper to closer where it is used.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Moving the helper to closer where it is used.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Moving the helper to closer where it is used.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Given that idr is only used to get id for thermal devices
(zones and cooling), makes sense to move the code closer.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Organize thermal core code to group the functions
handling with governor manipulation in one single section.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Here we have a simple code organization. This patch moves
functions that do not need to handle thermal core internal
data structure to thermal_helpers.c file.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This is a code reorganization, simply to concentrate
the sysfs handling functions in thermal_sysfs.c.
This patch moves the cooling device handling functions.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This is a code reorganization, simply to concentrate
the code handling sysfs in a specific file: thermal_sysfs.c.
Right now, moving only the sysfs entries of thermal_zone_device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch checks the return value of all calls to *scanf.
The check is to simply match the number of expect inputs.
The current code does not do any recovery in case the
number of treated inputs are different than the expected.
Therefore, keeping the same behavior.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch creates a helper to build a list of available governors.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Similarly to passive_store, policy_store now is split
between thermal core data structure handling and sysfs handling.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Given that cdevs sysfs properties are already registered using
the dev.groups, there is no need to explicitly call device_remove()
for each property.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Finally, move the last thermal zone sysfs attributes to
tz->device.groups: trips attributes. This requires adding a
attribute_group to thermal_zone_device, creating it dynamically, and
then setting all trips attributes in it. The trips attribute is then
added to the tz->device.groups.
As the removal of all attributes are handled by device core, the device
remove calls are not needed anymore.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This is a patch to allow adding groups created dynamically. For now we
create only the existing group. However, this is a preparation to allow
creating trip groups, which are determined only when the number of trips
are known at runtime.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Code reorganization to keep all the sysfs I/F of a thermal zone in the
same section.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Simply reorganize code to keep only functions of sysfs interface
of thermal zone device together. Therefore, move the power actor code
out of the sysfs I/F section.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Simple improvement on clarity and removal of checkpatch warning
in the documentation of power actor kernel doc.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch moves the passive attribute to tz->device.groups. Moving the
passive attribute also requires a .is_visible() callback implementation
for its attribute group.
The logic behind the visibility of passive attribute is kept the same.
We only expose the passive attribute if the thermal driver has exposed
at least one passive trip point.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Moving mode attribute to tz->device.groups requires the implementation
of a .is_visible() callback. The condition returned by .is_visible() of
the mode attribute group is kept the same, we allow the attribute to be
visible only if ops->get_mode() is set by the thermal driver.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Thermal zones attributes are all being created using
device_create_file(). This has the disadvantage of making the code
complicated and sometimes we may miss the cleanup of them.
This patch starts to move the thermal zone sysfs attributes to the
dev.groups, so Linux device core manage them for us. For now, this patch
only moves those attributes are always present regardless of thermal
zone condition.
This change has also the advantage of cleaning up the thermal zone
parameters sysfs entries that are left unclean after device
registration.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Simple code reorganization to group files that are always created
when registering a thermal zone.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Simply reorganize the code to have all DEVICE_ATTR's
in one point in the file.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There are APIs that rely on tz->type. This patch
prevent thermal zones without it to be registered.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch uses .driver_data and board_info[] to make per pci device
behavior table (name and ops), instead of adding the code for each pci
device in switch-case. This will make easier to add new pci device
ids.
Then this adds new device id actually for skylake PCH 100 series
(using registers are compatible with currently driver, so no need to
change except adding device id to table).
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use DEVICE_ATTR_RW for read-write attributes. This simplifies the
source code, improves readbility, and reduces the chance of
inconsistencies.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@rw@
declarer name DEVICE_ATTR;
identifier x,x_show,x_store;
@@
DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
@script:ocaml@
x << rw.x;
x_show << rw.x_show;
x_store << rw.x_store;
@@
if not (x^"_show" = x_show && x^"_store" = x_store)
then Coccilib.include_match false
@@
declarer name DEVICE_ATTR_RW;
identifier rw.x,rw.x_show,rw.x_store;
@@
- DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
+ DEVICE_ATTR_RW(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use DEVICE_ATTR_RO for read only attributes. This simplifies the
source code, improves readbility, and reduces the chance of
inconsistencies.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@ro@
declarer name DEVICE_ATTR;
identifier x,x_show;
@@
DEVICE_ATTR(x, \(0444\|S_IRUGO\), x_show, NULL);
@script:ocaml@
x << ro.x;
x_show << ro.x_show;
@@
if not (x^"_show" = x_show) then Coccilib.include_match false
@@
declarer name DEVICE_ATTR_RO;
identifier ro.x,ro.x_show;
@@
- DEVICE_ATTR(x, \(0444\|S_IRUGO\), x_show, NULL);
+ DEVICE_ATTR_RO(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Commit 3105f234e0 replaced module
cpu id table with a cpu feature check, which is logically correct.
But we need the module device table to allow module auto loading.
Cc: stable@vger.kernel.org # 4.8
Fixes:3105f234 thermal/powerclamp: correct cpu support check
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now genl_register_family() is the only thing (other than the
users themselves, perhaps, but I didn't find any doing that)
writing to the family struct.
In all families that I found, genl_register_family() is only
called from __init functions (some indirectly, in which case
I've add __init annotations to clarifly things), so all can
actually be marked __ro_after_init.
This protects the data structure from accidental corruption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial logic for checking CPU match resulted in OR of CPU features
rather than the intended AND.
Updated to use boot_cpu_has macro rather than x86_match_cpu.
In addition, MWAIT is the only required CPU feature for idle
injection to work. Drop other feature requirements since they are
only needed for optimal efficiency.
CC: stable@vger.kernel.org #v4.7
Signed-off-by: Eric Ernst <eric.ernst@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
On the platforms which has an ACPI companion device associated with
PCH thermal device, read passive trip temperature via ACPI _PSV
control method.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
When ACPI sends notification for trip point change re-read trips and
notify thermal core, so that this can be passed to user space thermal
controller.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Separated the code for reading trip points from int340x_thermal_zone_add to
a standalone function int340x_thermal_read_trips. This standlone
interface to read is exported so that int340x drivers can re-read trips
on ACPI notification for trip point change.
Also the appropriate notification events are sent by int340x driver based
on the acpi event using int340x_thermal_zone_device_update().
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add additional properties:
NAME= Thermal zone type
TEMP= Temperature sample value
TRIP= Violated trip index
EVENT= The notification event (new temperature sample, trip violation
trip changed)
This is the additional information to what kobject_uevent already
provides. So it will not impact existing user spaces.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Added one additional parameter to thermal_zone_device_update() to provide
caller with an optional capability to specify reason.
Currently this event is used by user space governor to trigger different
processing based on event code. Also it saves an additional call to read
temperature when the event is received.
The following events are cuurently defined:
- Unspecified event
- New temperature sample
- Trip point violated
- Trip point changed
- thermal device up and down
- thermal device power capability changed
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tegra132 use CCROC throttle registers to configure
pulse skiper, set these registers to enable throttle
function for Tegra132.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tegra soctherm support HW throttle, when the soctherm snesors'
temperature is above the throttle trip point, it will trigger
pulse skiper to tune clocks accroding to the throttle depth.
Add this function for Tegra124 and Tegra210.
Since Tegra132 use different registers to configure pulse skiper,
will support it in next patch.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_thermal_zone_of_sensor_register can fail, so check it's return value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds support for mt2701 chip to mtk_thermal,
and integrate both mt8173 and mt2701 on the same driver.
MT8173 has four banks and five sensors, and MT2701 has
only one bank and three sensors.
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Maxim Semiconductor Max77620 supports alarm interrupts when
its die temperature crosses 120C and 140C. These threshold
temperatures are not configurable.
Add thermal driver to register PMIC die temperature as thermal
zone sensor and capture the die temperature warning interrupts
to notifying the client.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When this platform is suspended, firmware powers the entire SoC down,
except a few hardware blocks waiting for wakeup events. There is no
context to save for this particular block.
Therefore, there is nothing useful for the driver to do on suspend;
so we define a NULL suspend hook. On resume, the driver initializes
the block exactly as is done in the probe callback.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We could see that state is defined as unsigned type, so it
should never be less than zero. Let' remove this check.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_thermal_zone_of_sensor_register() case doesn't need to call
thermal_zone_device_unregister().
Otherwise, rcar-thermal can't register thermal zone again after rebind.
This patch fixes it.
Signed-off-by: Bui Duc Phuc <bd-phuc@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Not much use unless the SoC is selected so depend on the ARCH_MXC
and COMPILE_TEST like all the other thermal drivers.
v2: drop extraneous OF
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In case of error, the function of_iomap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
And the function devm_regmap_init_mmio() returns ERR_PTR()
and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In less than 10 ms, the temperature of soc will arise 10 degree. 250 ms
is too big for soc tempeture control. Setting 2.5 ms will speed up
temperature accessing speed but introduce no more cpu's computing overhead.
We set AUTO_PERIOD_TIME and TSADCV3_AUTO_PERIOD_HT_TIME the same value,
because normal temperature update speed is also our consern in IPA.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Tested-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Due to the voltage ripple, the sensing data of the tsadc is not accurate.
And in this patch, the bandgap feature is enhanced to remove the voltage
ripple, and then the tsadc can sense the temperature more precisely.
Obsolete codes are removed as well.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Tested-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The newly added tsens-8916 driver produces warnings when CONFIG_PM
is disabled:
drivers/thermal/qcom/tsens.c:53:12: error: 'tsens_resume' defined but not used [-Werror=unused-function]
static int tsens_resume(struct device *dev)
^~~~~~~~~~~~
drivers/thermal/qcom/tsens.c:43:12: error: 'tsens_suspend' defined but not used [-Werror=unused-function]
static int tsens_suspend(struct device *dev)
^~~~~~~~~~~~~
This marks both functions __maybe_unused to let the compiler
know that they might be used in other configurations, without
adding ugly #ifdef logic.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This driver add thermal management support by enabling TMU (Thermal
Monitoring Unit) on QorIQ platform.
It's based on thermal of framework:
- Trip points defined in device tree.
- Cpufreq as cooling device registered in qoriq cpufreq driver.
Signed-off-by: Jia Hongtao <hongtao.jia@nxp.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
rcar-thermal is supporting both thermal_zone_of_sensor_register() and
thermal_zone_device_register(). But thermal_zone_of_sensor_register()
doesn't enable hwmon as default.
This patch enables it to keep compatibility
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Currently thermal zone set_emul_temp is set unconditionally
with of_thermal_set_emul_temp function. Set this only if the
set_emul_temp hook is provided for thermal_zone_of_device_ops.
This fixes emul_temp failures on platforms for which set_emul_temp
hook is not populated.
Fixes: "184a4bf623f (thermal: of: Extend current
of-thermal.c code to allow setting emulated temp)"
Suggested-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Conflicts:
drivers/thermal/of-thermal.c
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The hardware-tracked trips will set the alarm interrupt value for
registers. Then when the thermal zone has no trips to be set,
That make the thermal trips callback a over range value.
The root cause is the rk_tsadcv2_temp_to_code() function to handle the
invalid temperature range is indeed incorrect, let's fix it on now.
Otherwise, the thermal alarm interrupt will be triggered all the time
on some SoCs.
Fox example:
localhost tmp # grep thermal /proc/interrupts; sleep 5;
grep thermal /proc/interrupts
23: 994830 .. GICv3 129 Level rockchip_thermal
23: 1003423 .. GICv3 129 Level rockchip_thermal
Reported-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We should increase the period cycles to save power since the rk3399 has
the high frequency for tsadc clock.
Fixes commit b0d70338bc
("thermal: rockchip: Support the RK3399 SoCs in thermal driver")
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Whenever the current temperature is updated, the trip points immediately
below and above the current temperature are found. A sensor driver
callback `set_trips' is then called with the temperatures.
Lastly, The sensor will trigger the hardware high temperature interrupts
to increase the sampleing rate and throttle frequency to limit the
temperature rising When performing passive cooling.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Tested-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
With interrupt driven thermal zones we pass the lower and upper
temperature on which shall be acted, so in the governor we have to act on
the exact lower temperature to be consistent. Otherwise an interrupt maybe
generated on the exact lower temperature, but the bang bang governor does
not react since The polling driven zones have to be one step cooler before
the governor reacts.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Acked-by: Peter Feuerer <peter@piie.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The .get_trend callback in struct thermal_zone_device_ops has
the prototype:
int (*get_trend) (struct thermal_zone_device *, int,
enum thermal_trend *);
whereas the .get_trend callback in struct thermal_zone_of_device_ops
has:
int (*get_trend)(void *, long *);
Streamline both prototypes and add the trip argument to the OF callback
aswell and use enum thermal_trend * instead of an integer pointer.
While the OF prototype may be the better one, this should be decided at
framework level and not on OF level.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This adds support for hardware-tracked trip points to the device tree
thermal sensor framework.
The framework supports an arbitrary number of trip points. Whenever
the current temperature is updated, the trip points immediately
below and above the current temperature are found. A .set_trips
callback is then called with the temperatures. If there is no trip
point above or below the current temperature, the passed trip
temperature will be -INT_MAX or INT_MAX respectively. In this callback,
the driver should program the hardware such that it is notified
when either of these trip points are triggered. When a trip point
is triggered, the driver should call `thermal_zone_device_update'
for the respective thermal zone. This will cause the trip points
to be updated again.
If .set_trips is not implemented, the framework behaves as before.
This patch is based on an earlier version from Mikko Perttunen
<mikko.perttunen@kapsi.fi>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Trivial: remove the following:
drivers/thermal/qcom/tsens-8916.c:103:24: warning: symbol 'ops_8916' was not declared. Should it be static?
drivers/thermal/qcom/tsens-8996.c:76:24: warning: symbol 'ops_8996' was not declared. Should it be static?
drivers/thermal/qcom/tsens-8974.c:235:24: warning: symbol 'ops_8974' was not declared. Should it be static?
drivers/thermal/qcom/tsens-8960.c:279:24: warning: symbol 'ops_8960' was not declared. Should it be static?
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The TSENS controller in 8996 family of SoCs is capable of converting the
ADC code outputs to real temperature values (in decidegree Celsius).
It can also be programmed to provide raw ADC code, but the secure software
on 8996 programs it to provide real temperatures and also does the needed
calibrations.
We check the valid bit to ensure valid data is read by the AHB master.
And the spec recommends the below algorithm to read data 3 consecutive
times, which takes care of the worst case delay taken to propagate the
updated data to the register.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
8960 family of SoCs have the TSENS device as part of GCC, hence
the driver probes the virtual child device created by GCC and
uses the parent to extract all DT properties and reuses the GCC
regmap.
Also GCC/TSENS are part of a domain thats not always ON.
Hence add .suspend and .resume hooks to save and restore some of
the inited register context.
Also 8960 family have some of the TSENS init sequence thats
required to be done by the HLOS driver (some later versions of TSENS
do not export these registers to non-secure world, and hence need
these initializations to be done by secure bootloaders)
8660 from the same family has just one sensor and hence some register
offset/layout differences which need special handling in the driver.
Based on the original code from Siddartha Mohanadoss, Stephen Boyd and
Narendran Rajan.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add apis for platform thermal drivers to query for slope and offset
attributes, which might be needed for temperature calculations.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add .calibrate support for 8974 family as part of tsens_ops.
Based on the original code by Siddartha Mohanadoss and Stephen Boyd.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add support to calibrate sensors on 8916 family and also add common
functions to read temperature from sensors (This can be reused on
other SoCs having similar TSENS device)
The calibration data is read from eeprom using the generic nvmem
framework apis.
Based on the original code by Siddartha Mohanadoss and Stephen Boyd.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
TSENS is Qualcomms' thermal temperature sensor device. It
supports reading temperatures from multiple thermal sensors
present on various QCOM SoCs.
Calibration data is generally read from a non-volatile memory
(eeprom) device.
Add a skeleton driver with all the necessary abstractions so
a variety of qcom device families which support TSENS can
add driver extensions.
Also add the required device tree bindings which can be used
to describe the TSENS device in DT.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The last_load is updated not cpufreq_get_actual_power() function call
but cpufreq_get_requested_power() function call.
Signed-off-by: Inhyuk Kang <hugh.kang@lge.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Javi Merino <javi.merino@arm.com>
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In case thermal_zone_xxx_register() returns an error, priv->zone
isn't NULL any more, but contains the error code.
This is passed to thermal_zone_device_unregister(), then. This checks
for priv->zone being NULL, but the error code is != NULL. So it works
with the error code as a pointer. Crashing immediately.
To fix this, reset priv->zone to NULL before entering
rcar_gen3_thermal_remove().
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This change adds support for Intel BXT Whiskey Cove PMIC thermal
driver which is intended to handle the alert interrupts triggered
upon thermal trip point cross and notify the thermal framework
appropriately with the zone, temp, crossed trip and event details.
Signed-off-by: Yegnesh S Iyer <yegnesh.s.iyer@intel.com>
Signed-off-by: Bin Gao <bin.gao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later at line 472:
data->socdata = of_id->data;
For fixing this problem, we use of_device_get_match_data(), this will
simplify the code a little by using a standard function for
getting the match data.
Reported-by: coverity (CID 1324128)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Currently all CPU cooling devices share a
`struct thermal_cooling_device_ops` instance. The thermal core uses the
presence of functions in this struct to determine if a cooling device
has a power model (see cdev_is_power_actor). cpu_cooling.c adds the
power model functions to the shared struct when a device is registered
with a power model.
Therefore, if a CPU cooling device is registered using
[of_]cpufreq_power_cooling_register, _all_ devices will be determined to
have a power model, including any registered with
[of_]cpufreq_cooling_register. This can result in cpufreq_state2power
being called on a device where dyn_power_table is NULL.
With this commit, instead of having a shared thermal_cooling_device_ops
which is mutated, we have two versions: one with the power functions and
one without.
Signed-off-by: Brendan Jackman <brendan.jackman@arm.com>
Cc: Amit Daniel Kachhap <amit.kachhap@gmail.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Javi Merino <javi.merino@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The driver allocates the mutex but not initialize it.
Use mutex_init() on it to initialize it correctly.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When multiple thermal zones are bound to the same cooling device, multiple
kernel threads may want to update the cooling device state by calling
thermal_cdev_update(). Having cdev not protected by a mutex can lead to a race
condition. Consider the following situation with two kernel threads k1 and k2:
Thread k1 Thread k2
||
|| call thermal_cdev_update()
|| ...
|| set_cur_state(cdev, target);
call power_actor_set_power() ||
... ||
instance->target = state; ||
cdev->updated = false; ||
|| cdev->updated = true;
|| // completes execution
call thermal_cdev_update() ||
// cdev->updated == true ||
return; ||
\/
time
k2 has already looped through the thermal instances looking for the deepest
cooling device state and is preempted right before setting cdev->updated to
true. Now, k1 runs, modifies the thermal instance state and sets cdev->updated
to false. Then, k1 is preempted and k2 continues the execution by setting
cdev->updated to true, therefore preventing k1 from performing the update.
Notice that this is not an issue if k2 looks at the instance->target modified by
k1 "after" it is assigned by k1. In fact, in this case the update will happen
anyway and k1 can safely return immediately from thermal_cdev_update().
This may lead to a situation where a thermal governor never updates the cooling
device. For example, this is the case for the step_wise governor: when calling
the function thermal_zone_trip_update(), the governor may always get a new state
equal to the old one (which, however, wasn't notified to the cooling device) and
will therefore skip the update.
CC: Zhang Rui <rui.zhang@intel.com>
CC: Eduardo Valentin <edubezval@gmail.com>
CC: Peter Feuerer <peter@piie.net>
Reported-by: Toby Huang <toby.huang@arm.com>
Signed-off-by: Michele Di Giorgio <michele.digiorgio@arm.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Added suspend/resume callback to disable/enable PCH thermal sensor
respectively. If the sensor is enabled by the BIOS, then the sensor status
will not be changed during suspend/resume.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull thermal management fixes from Zhang Rui:
- fix an ordering issue in cpu cooling that cooling device is
registered before it's ready (freq_table being populated).
(Lukasz Luba)
- fix a missing comment update (Caesar Wang)
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: add the note for set_trip_temp
thermal: cpu_cooling: fix improper order during initialization
Most of the callers of cpufreq_frequency_get_table() already have the
pointer to a valid 'policy' structure and they don't really need to go
through the per-cpu variable first and then a check to validate the
frequency, in order to find the freq-table for the policy.
Directly use the policy->freq_table field instead for them.
Only one user of that API is left after above changes, cpu_cooling.c and
it accesses the freq_table in a racy way as the policy can get freed in
between.
Fix it by using cpufreq_cpu_get() properly.
Since there are no more users of cpufreq_frequency_get_table() left, get
rid of it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Javi Merino <javi.merino@arm.com> (cpu_cooling.c)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The X86_FAMILY_ANY in here is bogus. "BYT" and model 0x37 are
family-6 only.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: jacob.jun.pan@intel.com
Cc: linux-pm@vger.kernel.org
Link: http://lkml.kernel.org/r/20160603001952.9B6E114D@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The freq_table array is not populated before calling
thermal_of_cooling_register. The code which populates the freq table was
introduced in commit f6859014.
This should be done before registering new thermal cooling device.
The log shows effects of this wrong decision.
[ 2.172614] cpu cpu1: Failed to get voltage for frequency 1984518656000: -34
[ 2.220863] cpu cpu0: Failed to get voltage for frequency 1984524416000: -34
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: f6859014c7 ("thermal: cpu_cooling: Store frequencies in descending order")
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Javi Merino <javi.merino@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
commit 059500940d (ACPI/video: export acpi_video_get_levels)
mistakenly dropped the correct value of max_level and that caused the
set_level function following failed and the acpi_video backlight interface
didn't get created. Fix this by passing back the correct max_level value.
While at it, also fix the param used in acpi_video_device_lcd_query_levels
where acpi_handle is expected but acpi_video_device is passed.
Fixes: 059500940d (ACPI/video: export acpi_video_get_levels)
Reported-and-tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull thermal management updates from Zhang Rui:
- Introduce generic ADC thermal driver, based on OF thermal (Laxman
Dewangan)
- Introduce new thermal driver for Tango chips (Marc Gonzalez)
- Rockchip driver support for RK3399, RK3366, and some fixes (Caesar
Wang, Elaine Zhang and Shawn Lin)
- Add CPU power cooling model to Mediatek thermal driver (Dawei Chien)
- Wider usage of dev_thermal_zone_of_sensor_register (Eduardo Valentin)
- TI thermal driver gained a new maintainer (Keerthy).
- Enabled powerclamp driver by checking CPU feature and package cstate
counter instead of CPU whitelist (Jacob Pan)
- Various fixes on thermal governor, OF thermal, Tegra, and RCAR
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (50 commits)
thermal: tango: initialize TEMPSI_CFG
thermal: rockchip: use the usleep_range instead of udelay
thermal: rockchip: add the notes for better reading
thermal: rockchip: Support RK3366 SoCs in the thermal driver
thermal: rockchip: handle the power sequence for tsadc controller
thermal: rockchip: update the tsadc table for rk3399
thermal: rockchip: fixes the code_to_temp for tsadc driver
thermal: rockchip: disable thermal->clk in err case
thermal: tegra: add Tegra132 specific SOC_THERM driver
thermal: fix ptr_ret.cocci warnings
thermal: mediatek: Add cpu dynamic power cooling model.
thermal: generic-adc: Add ADC based thermal sensor driver
thermal: generic-adc: Add DT binding for ADC based thermal sensor
thermal: tegra: fix static checker warning
thermal: tegra: mark PM functions __maybe_unused
thermal: add temperature sensor support for tango SoC
thermal: hisilicon: fix IRQ imbalance enabling
thermal: hisilicon: support to use any sensor
thermal: rcar: Remove binding docs for r8a7794
thermal: tegra: add PM support
...
TEMPSI_CFG is not equal to 0 at reset. It must be initialized.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Documentation/timers/timers-howto.txt recommends to use
usleep_range on delays > 10usec.
The usleep_range indeed reduces CPU load, since the udelay will busy wait
for enough loop cycles to achieve the desired delay.
Fixes commit b06c52db39fd ("thermal: rockchip:
handle the power sequence for tsadc controller").
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
To update the notes for keeping in mind that quickly in case
someone re-read this driver in the future.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The RK3366 SoCs have two Temperature Sensors, channel 0 is for CPU
channel 1 is for GPU.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This adds the grf property to handle the tsadc power sequence on
rockchip some SoCs.
Verified on rk3399 can work with this patch on now.
while true; do grep "" /sys/class/thermal/thermal_zone[0-1]/temp
sleep .5; done
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41666
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch fixes the incorrect conversion table.
The Code to Temperature mapping is updated based on sillcon results.
Fixes commit b0d70338bc
("thermal: rockchip: Support the RK3399 SoCs in thermal driver").
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We should judge the table.id[mid].code insearch algorithm on matter the
adc value increment or decrement.
Or otherwise, the temperature return the incorrect value in some cases.
[ 1.438589] adc_val=402,temp=-40000
[ 1.438903] adc_val=403,temp=-39375
[ 1.439217] adc_val=404,temp=-38750
...
[ 1.441102] adc_val=410,temp=-40000
[ 1.441416] adc_val=411,temp=-34445
[ 1.441737] adc_val=412,temp=-33889
...
Let's fix it right now.
Fixes commit 020ba95dbb ("thermal: rockchip:
Add the sort mode for adc value increment or decrement").
Reported-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Disable thermal->clk when enabling pclk fails in
resume routine.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
drivers/thermal/tango_thermal.c:86:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
CC: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In some of platform, thermal sensors like NCT thermistors are
connected to the one of ADC channel. The temperature is read by
reading the voltage across the sensor resistance via ADC. Lookup
table for ADC read value to temperature is referred to get
temperature. ADC is read via IIO framework.
Add support for thermal sensor driver which read the voltage across
sensor resistance from ADC through IIO framework.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There has a static checker warning:
warn: variable dereferenced before check 'dev' (see line 222)
Since check 'dev' is unnecessary, so remove this check.
Fixes: ee6d79f202a4 ("thermal: tegra: add thermtrip function")
Signed-off-by: Wei Ni <wni@nvidia.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
After the PM support has been added to this driver, we get
a harmless warning when that support is disabled at compile
time:
drivers/thermal/tegra/soctherm.c:641:12: error: 'soctherm_resume' defined but not used [-Werror=unused-function]
static int soctherm_resume(struct device *dev)
This marks the two PM functions as __maybe_unused to shut up
the warning. This is preferred over adding an #ifdef around
them, as it is harder to get wrong, and provides better
compile-time coverage.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a134b4143b65 ("thermal: tegra: add PM support")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The Tango thermal driver provides support for the primitive temperature
sensor embedded in Tango chips since the SMP8758.
This sensor only generates a 1-bit signal to indicate whether the die
temperature exceeds a programmable threshold.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When register sensors into thermal zone during initialization phase, it
reports error for IRQ imbalance enabling:
[ 2.040713] WARNING: at kernel/irq/manage.c:513
[ 2.040719] Modules linked in:
[ 2.040721]
[ 2.040729] CPU: 1 PID: 804 Comm: irq/33-hisi_the Not tainted 4.5.0-rc4+ #505
[ 2.040732] Hardware name: HiKey Development Board (DT)
[ 2.040736] task: ffffffc03ae82580 ti: ffffffc0379c8000 task.ti: ffffffc0379c8000
[ 2.040745] PC is at __enable_irq+0x74/0x84
[ 2.040749] LR is at __enable_irq+0x74/0x84
This warning is for IRQ imbalance enabling, which is caused by
enable_irq() twice. During sensor's initialization it tries to enable
IRQ, the driver will call thermal_zone_of_sensor_register() to bind
sensors and read sensor's temperature. But at this moment the flag
"data->irq_enabled" has been not initialized as correct state, so it
finally introduces the function enabled_irq() to be called twice. In
essentially this is caused by the flag "data->irq_enabled" is
inconsistent with real hardware IRQ enabling state.
So this patch is to fix this issue, firstly init "irq_enabled" flag
before binding sensors to thermal zone. Also change to use the function
irq_get_irqchip_state() to read back real interrupt line state.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In current code sensor driver registers all 4 sensors together and if
any of them has not bound to thermal zone successfully then driver will
return failure for driver's initialization. As a result, if DT binds
thermal zone with only one sensor, then the thermal driver will not work
well anymore.
So this patch is to fix this issue. It allows the thermal sensor driver
can register any number sensors at initialization phase, and fix up code
for other related code to skip related sensor's accessing if the sensor
has not been enabled in initialization phase.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Handle HW initialization in one function soctherm_init(),
so that the codes are more clear.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Handle clock enable/disable codes in one function
soctherm_clk_enable(), so that the codes are more clear.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support for hardware critical thermal limits to the
SOC_THERM driver. It use the Linux thermal framework to
create critical trip temp, and set it to SOC_THERM hardware.
If these limits are breached, the chip will reset, and if
appropriately configured, will turn off the PMIC.
This support is critical for safe usage of the chip.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In current of-thermal, the .set_trip_temp only support to
set trip_temp for SW. But some sensors support to set
trip_temp on hardware, so that can trigger interrupt,
shutdown or any other events.
This patch adds .set_trip_temp() callback in
thermal_zone_of_device_ops{}, so that the sensor device can
use it to set trip_temp on hardware.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a debugfs interface to show register contents for debug.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Split most of the Tegra124 data and code into a Tegra124-specific
file.
Split most of the fuse-related code into a fuse-related source file.
This is in preparation for adding a Tegra210-specific driver in a
future patch.
Beyond the maintainability improvements, this is intended to separate
chip-specific ATE and characterization-related hacks into chip-specific
files, in the hopes that they won't pollute code for other chips.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Get rid of T124-specific PDIV/HOTSPOT hack.
tegra-soctherm.c contained a hack to set the SENSOR_PDIV and
SENSOR_HOTSPOT_OFFSET registers - it just did two writes of
T124-specific opaque values. Convert these into a form that can be
substituted on a per-chip basis, and into structure fields that have
at least some independent meaning.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Combine sensor group-related data structures into struct
tegra_tsensor_group. This provides a single location for
sensor group data storage.
More sensor group data will be added in subsequent patches.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Move Tegra soctherm driver to tegra directory, it's easy to maintain
and add more new function support for Tegra platforms.
This will also help to split soctherm driver into common parts and
chip specific data related parts.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
of_node_put is iterating through all terms in the tbps array even though
the bind has failed. We need to only iterate through the terms that have
already passed the binding step.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ulises Brindis <brindisu@lab126.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When performing a suspend operation, the kernel brings all of the
non-boot CPUs offline, calling the hot plug notifiers with the flag,
CPU_TASKS_FROZEN, set in the action code. Similarly, during resume,
the CPUs are brought back online, but again the notifiers have the
FROZEN flag set.
While some very few drivers really need to treat suspend/resume
specially, this driver unintentionally ignores the notifications.
This patch changes the driver to cancel its work item when the CPU
goes down, even during a suspend operation. As a result, the
suspended state is no longer a special case.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Bang-bang thermal governor uses trip point hysteresis to make decisions.
Hysteresis is a required property in the device tree for trip points, but it is
an optional thermal zone device operation. Hence, we need to check whether the
function pointer is valid or not.
If it is not available, we assume the hysteresis to be zero. Consequently, a
highly varying temperature will make the governor continuosly switch a cooling
device ON and OFF.
CC: Zhang Rui <rui.zhang@intel.com>
CC: Eduardo Valentin <edubezval@gmail.com>
CC: Peter Feuerer <peter@piie.net>
Signed-off-by: Michele Di Giorgio <michele.digiorgio@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
INT3406 ACPI device object resembles an ACPI video output device, but its
_BCM is said to be deprecated and should not be used. So we will make
use of the raw interface to do the actual cooling.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
BIOS/EC can change PPCC element dynamically and inform OS about the change.
When this driver receives notification, it will read PPCC element again.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Powerclamp works by aligning idle time to achieve package level
idle states, aka cstates. As long as one of the package cstates
is available, synchronized idle injection is meaningful.
This patch replaces the CPU whitelist with CPU feature and
package cstate counter check such that we don't have to modify
this whitelist for every new CPU.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Power allocator's parameters are S32 type, so use %d to print them.
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When calculate temperature, old code firstly do division and then
convert to "millicelsius" unit. This will lose resolution and only can
read back temperature with "Celsius" unit.
So firstly scale step value to "millicelsius" and then do division, so
finally we can increase resolution for temperature value. Also refine
the calculation from temperature value to step value.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
At least with CONFIG_COMPILE_TEST, there's no reason to assume
that CONFIG_RESET_CONTROLLER is set, but the code for this
controller requires it since it calls device_reset().
Make CONFIG_MTK_THERMAL properly depend on CONFIG_RESET_CONTROLLER.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The commit 17e8351a77 consistently use int for temperature,
however it missed a few in trip temperature and thermal_core.
In current codes, the trip->temperature used "unsigned long"
and zone->temperature used"int", if the temperature is negative
value, it will get wrong result when compare temperature with
trip temperature.
This patch can fix it.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
req_range is declared as a u64 to cope with overflows in the
multiplication of two u32. As both req_power and power_range are u32,
we need to make sure the multiplication is done with u64 types.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add __init attribute on a function that is only called from other __init
functions and that is not inlined, at least with gcc version 4.8.4 on an
x86 machine with allyesconfig. Currently, the function is put in the
.text.unlikely segment. Declaring it as __init will cause it to be put in
the .init.text and to disappear after initialization.
The result of objdump -x on the function before the change is as follows:
0000000000000086 l F .text.unlikely 0000000000000739 thermal_of_build_thermal_zone
And after the change it is as follows:
0000000000000000 l F .init.text 0000000000000734 thermal_of_build_thermal_zone
Done with the help of Coccinelle. The semantic patch checks for local
static non-init functions that are called from an __init function and are
not called from any other function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In some cases, platform thermal driver may report invalid trip points,
thermal core should not take any action for these trip points.
This fixed a regression that bogus trip point starts to screw up thermal
control on some Lenovo laptops, after
commit bb431ba26c
Author: Zhang Rui <rui.zhang@intel.com>
Date: Fri Oct 30 16:31:47 2015 +0800
Thermal: initialize thermal zone device correctly
After thermal zone device registered, as we have not read any
temperature before, thus tz->temperature should not be 0,
which actually means 0C, and thermal trend is not available.
In this case, we need specially handling for the first
thermal_zone_device_update().
Both thermal core framework and step_wise governor is
enhanced to handle this. And since the step_wise governor
is the only one that uses trends, so it's the only thermal
governor that needs to be updated.
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
CC: <stable@vger.kernel.org> #3.18+
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1317190
Link: https://bugzilla.kernel.org/show_bug.cgi?id=114551
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enabled temperature reporting device of Skylake Platform Controller hub.
The register map is same as the wildcat point thermal currently implemented
in this driver.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add resource managed version of thermal_zone_of_sensor_register() and
thermal_zone_of_sensor_unregister().
This helps in reducing the code size in error path, remove of
driver remove callbacks and making proper sequence for deallocations.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The driver doesn't check if the regulator_get_optional return value is
-EPROBE_DEFER so it will wrongly assume that the regulator couldn't be
found just because the regulator driver wasn't registered yet, i.e:
exynos-tmu 10060000.tmu: Regulator node (vtmu) not found
In this case the return value should be propagated to allow the driver
probe function to be deferred until the regulator driver is registered.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The Exynos TMU DT binding says that the vtmu-supply is optional but the
driver uses devm_regulator_get() that creates a dummy regulator if it's
not defined in the DT. For example the following message is in the log:
10060000.tmu supply vtmu not found, using dummy regulator
Use the optional version of regulator_get() that doesn't create a dummy
regulator and instead returns a -ENODEV errno code. Since it's expected
that a regulator may not be defined and the driver will inform about it:
exynos-tmu 10060000.tmu: Regulator node (vtmu) not found
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When DeviveTree contains more trip-points than SoC can configure
(usually more than four) and polling mode is not enabled, then the
remaining trip-points will be silently ignored. No interrupts will be
generated for them.
This might be quite dangerous when one provides DTB with a
non-configurable critical trip-point, like (assuming four supported
thresholds in TMU):
- alert @50 C (type: active),
- alert @60 C (type: active),
- alert @70 C (type: active),
- alert @80 C (type: active),
- critical @120 C (type: critical) <- no interrupts generated.
This is a mistake in DTB so print a message in such case.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The sign bit of temperature readback is bit 0, not bit 1.
Change to BIT(0) to fix it.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Matt Longnecker <mlongnecker@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed on many files with:
drivers/built-in.o: In function `kirkwood_thermal_probe':
kirkwood_thermal.c:(.text+0x390a25): undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `exynos_tmu_probe':
exynos_tmu.c:(.text+0x39246b): undefined reference to `devm_ioremap'
The users of devm_ioremap_resource() which are compile-testable should
depend on HAS_IOMEM.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We don't need to initialize "ret". We can move the IS_ERR() checks into
the if condition instead of doing an assignment first. Also there is a
check for "ret" when we know it is zero so we can remove that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This driver only has runtime but no build time dependencies, so it can be
built for testing purposes if the Kconfig COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that drivers are
not affected by changes that could cause build regressions.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As the TRM says, add the tsadc_q_sel to control the temperature-code
sequence since the rk3228/rk3399 need set this bit (1024 - tsadc_q)
as output.
Fixes: commit
b0d7033 "thermal: rockchip: Support the RK3399 SoCs in thermal driver"
7b02a5e "thermal: rockchip: Support the RK3228 SoCs in thermal driver"
Reported-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch renames to be more adapter compatibles since more and more
SoCs are supported in thermal driver.
Reported-by: Huang,Tao <huangtao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
the calculation use a global table, not their own table.
so adapt the table to the correct one.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As the Dan report the smatch check the thermal driver warning:
drivers/thermal/rockchip_thermal.c:551 rockchip_configure_from_dt()
warn: impossible condition '(thermal->tshut_temp > ((~0 >> 1))) =>
(s32min-s32max > s32max)'
Although The shut_temp read from DT is u32,the temperature is currently
represented as int not long in the thermal driver.
Let's change to make shut_temp instead of the thermal->tshut_temp for
the condition.
Fixes: commit 437df2172e
("thermal: rockchip: consistently use int for temperatures")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This adds support for the Mediatek thermal controller found on MT8173
and likely other SoCs.
The controller is a bit special. It does not have its own ADC, instead
it controls the on-SoC AUXADC via AHB bus accesses. For this reason
we need the physical address of the AUXADC. Also it controls a mux
using AHB bus accesses, so we need the APMIXEDSYS physical address aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In __cpufreq_cooling_register() we allocate the arrays for time_in_idle
and time_in_idle_timestamp to be as big as the number of cpus in this
cpufreq device. However, in get_load() we access this array using the
cpu number as index, which can result in an out of bound access.
Index time_in_idle{,_timestamp} using the index in the cpufreq_device's
allowed_cpus mask, as we do for the load_cpu array in
cpufreq_get_requested_power()
Reported-by: Nicolas Boichat <drinkcat@chromium.org>
Cc: Amit Daniel Kachhap <amit.kachhap@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When the thermal subsystem is a loadable module, the u8500 driver
fails to build:
drivers/thermal/built-in.o: In function `db8500_thermal_probe':
db8500_thermal.c:(.text+0x96c): undefined reference to `thermal_zone_device_register'
drivers/thermal/built-in.o: In function `db8500_thermal_work':
db8500_thermal.c:(.text+0xab4): undefined reference to `thermal_zone_device_update'
This changes the symbol to a tristate, so Kconfig can track the
dependency correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When the thermal subsystem is a loadable module, the spear driver
fails to build:
drivers/thermal/built-in.o: In function `spear_thermal_exit':
spear_thermal.c:(.text+0xf8): undefined reference to `thermal_zone_device_unregister'
drivers/thermal/built-in.o: In function `spear_thermal_probe':
spear_thermal.c:(.text+0x230): undefined reference to `thermal_zone_device_register'
This changes the symbol to a tristate, so Kconfig can track the
dependency correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The spear thermal driver hides its suspend/resume function conditionally
based on CONFIG_PM, but references them based on CONFIG_PM_SLEEP, so
we get a warning if the former is set but the latter is not:
thermal/spear_thermal.c:58:12: warning: 'spear_thermal_suspend' defined but not used [-Wunused-function]
thermal/spear_thermal.c:75:12: warning: 'spear_thermal_resume' defined but not used [-Wunused-function]
This removes the #ifdef and instead uses a __maybe_uninitialized
annotation to avoid the warning and improve compile-time coverage.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch enables to use thermal-zone on DT if it was calles as
"renesas,rcar-thermal-gen2".
Previous style (= non thermal-zone) is still supported by
"renesas,rcar-thermal" to keep compatibility for "git bisect".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Use for_each_available_child_of_node() for iterating over each
available child instead of iterating over each child and then
checking their status.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull thermal management updates from Zhang Rui:
"The top merge commit was re-generated yesterday because two topic
branches were dropped from this pull request in the last minute due to
some unaddressed comments. All the other material has been in
linux-next for quite a while.
Specifics:
- Enhance thermal core to handle unexpected device cooling states
after fresh boot and system resume. From Zhang Rui and Chen Yu.
- Several fixes and cleanups on Rockchip and RCAR thermal drivers.
From Caesar Wang and Kuninori Morimoto.
- Add Broxton support for Intel processor thermal reporting device
driver. From Amy Wiles"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: trip_point_temp_store() calls thermal_zone_device_update()
thermal: rcar: rcar_thermal_get_temp() return error if strange temp
thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
thermal: rcar: check every rcar_thermal_update_temp() return value
thermal: rcar: move rcar_thermal_dt_ids to upside
thermal: rockchip: Support the RK3399 SoCs in thermal driver
thermal: rockchip: Support the RK3228 SoCs in thermal driver
dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
thermal: rockchip: fix a trivial typo
Thermal: Enable Broxton SoC thermal reporting device
thermal: constify pch_dev_ops structure
Thermal: do thermal zone update after a cooling device registered
Thermal: handle thermal zone device properly during system sleep
Thermal: initialize thermal zone device correctly
Current rcar thermal driver sometimes checks irq possibility when it
calls rcar_thermal_irq_enable/disable(), but sometimes not.
This patch checks it inside rcar_thermal_irq_enable/disable().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Every rcar_thermal_update_temp() return value will be checked.
And also, rcar_thermal_get_temp() always call
rcar_thermal_update_temp() by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch is prepare for of-thermal support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The RK3399 SoCs have two Temperature Sensors, channel 0 is for CPU.
channel 1 is for GPU.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The RK3228 SoCs has one Temperature Sensor, channel 0 is for CPU.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patchset trys to dictate unified format for driver.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The pch_dev_ops structure is never modified. It is only stored in a field
that is already declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When a new cooling device is registered, we need to update the
thermal zone to set the new registered cooling device to a proper
state.
This fixes a problem that the system is cool, while the fan devices
are left running on full speed after boot, if fan device is registered
after thermal zone device.
Here is the history of why current patch looks like this:
https://patchwork.kernel.org/patch/7273041/
CC: <stable@vger.kernel.org> #3.18+
Reference:https://bugzilla.kernel.org/show_bug.cgi?id=92431
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Current thermal code does not handle system sleep well because
1. the cooling device cooling state may be changed during suspend
2. the previous temperature reading becomes invalid after resumed because
it is got before system sleep
3. updating thermal zone device during suspending/resuming
is wrong because some devices may have already been suspended
or may have not been resumed.
Thus, the proper way to do this is to cancel all thermal zone
device update requirements during suspend/resume, and after all
the devices have been resumed, reset and update every registered
thermal zone devices.
This also fixes a regression introduced by:
Commit 19593a1fb1 ("ACPI / fan: convert to platform driver")
Because, with above commit applied, all the fan devices are attached
to the acpi_general_pm_domain, and they are turned on by the pm_domain
automatically after resume, without the awareness of thermal core.
CC: <stable@vger.kernel.org> #3.18+
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=78201
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=91411
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
After thermal zone device registered, as we have not read any
temperature before, thus tz->temperature should not be 0,
which actually means 0C, and thermal trend is not available.
In this case, we need specially handling for the first
thermal_zone_device_update().
Both thermal core framework and step_wise governor is
enhanced to handle this. And since the step_wise governor
is the only one that uses trends, so it's the only thermal
governor that needs to be updated.
CC: <stable@vger.kernel.org> #3.18+
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
The read and write opcodes are global for all units on SoC and even across
Intel SoCs. Remove duplication of corresponding constants. At the same time
convert all current users.
No functional change.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boon Leong Ong <boon.leong.ong@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The IMX6Q/IMX6DL SoC's have a 2-bit temperature grade stored in OTP which
is valid for all IMX6 SoC's (despite the fact that the IMXSDLRM and
IMXSXRM do not document this - this has been proven via tests as well as
verified by Freescale FAE).
Instead of assuming a fixed 85C for passive cooling threshold and 105C for
critical use the thermal grade for these configurations.
We will set the critical to maxT - 5C and passive to maxT - 10C.
Cc: Anson Huang <b20788@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
----
v3:
- rebase against linux-soc-thermal.git
- added ack's from Shawn and Jon
v2:
- remove check for IMX6Q and update comments: The OTP values have been tested
on IMX6SOLO, IMX6DUALLITE, and IMX6SX and Freescale FAE has shared data with
me that the OTP settings are the same and that the reference manuals will
reflect this in their next updates.
- set critical to max - 5C
- set passive to max - 10C
- display max temp in info
- do not allow passive to be set above critical
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This just caused build errors:
warning: (QCOM_SPMI_TEMP_ALARM) selects REGMAP_SPMI which has unmet direct dependencies (SPMI)
drivers/built-in.o: In function `regmap_spmi_ext_gather_write':
:(.text+0x609b0): undefined reference to `spmi_ext_register_write'
:(.text+0x609f0): undefined reference to `spmi_ext_register_writel'
While it's generally a good idea to allow compile testing, in this
case, it just doesn't work, so reverting the patch that
introduced the compile-test variant seems the most appropriate
solution.
Note that SPMI also has a 'depends on ARCH_QCOM || COMPILE_TEST'
statement, so we should be able to enable SPMI on all architectures
for compile testing already.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: cb7fb4d342 ("thermal: qcom_spmi: allow compile test")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Probe error operation and remove operation are same.
Let's use same function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Some systems register thermal zone by themself and don't need to
have thermal zones node in DT. Therefore reduce the log level from
ERROR to DEBUG when thermal zone node can't be find in
of_thermal_destroy_zones().
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
All thermal governors use the temperature value stored in
struct thermal_zone_device.
thermal_zone_device->temperature
power_allocator governor should not deviate from this and use
the same.
Cc: Javi Merino <javi.merino@arm.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Javi Merino <javi.merino@arm.com>
Reported-by: Sugumar Natarajan <sugumar.natarajan@arm.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The RK3368 SoCs support to 2 channel TS-ADC, the temperature criteria
of each channel can be configurable.
The system has two Temperature Sensors, channel 0 is for CPU,
and channel 1 is for GPU.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As Temperature is currently represented as int not long in the thermal
framework since use int intead of unsigned long/long to represent
temperature to avoid bogus overheat detection when negative temperature
reported.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The conversion table has the adc value and temperature.
In fact, the adc value only has the increment or decrement mode in
conversion table.
Moment, we can add the sort mode to be better support the *code_to_temp*
for differenr SoCs.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We should make the conversion table in as a parameter since the different
SoCs have the different conversionion table.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The current driver is default to register the two thermal sensors
in probe since some SoCs maybe only have one sensor for thermal.
In some cases, the channel 0 is not always the cpu or gpu sensor.
So add the channel can be configured for sensors.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Missing a include file caused compile error.
drivers/thermal/rockchip_thermal.c: In function 'rockchip_thermal_suspend':
drivers/thermal/rockchip_thermal.c:720:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
...
Fixes: 7e38a5b1da ("thermal: rockchip: support the sleep pinctrl state
to avoid glitches")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull thermal updates from Zhang Rui:
- Implement generic devfreq cooling mechanism through frequency
reduction for devices using devfreq. From Ørjan Eide and Javi
Merino.
- Introduce OMAP3 support on TI SoC thermal driver. From Pavel Mack
and Eduardo Valentin.
- A bounch of small fixes on devfreq_cooling, Exynos, IMX, Armada, and
Rockchip thermal drivers.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (24 commits)
thermal: exynos: Directly return 0 instead of using local ret variable
thermal: exynos: Remove unneeded semicolon
thermal: exynos: Use IS_ERR() because regulator cannot be NULL
thermal: exynos: Fix first temperature read after registering sensor
thermal: exynos: Fix unbalanced regulator disable on probe failure
devfreq_cooling: return on allocation failure
thermal: rockchip: support the sleep pinctrl state to avoid glitches in s2r
dt-bindings: rockchip-thermal: Add the pinctrl states in this document
thermal: devfreq_cooling: Make power a u64
thermal: devfreq_cooling: use a thermal_cooling_device for register and unregister
thermal: underflow bug in imx_set_trip_temp()
thermal: armada: Fix possible overflow in the Armada 380 thermal sensor formula
thermal: imx: register irq handler later in probe
thermal: rockhip: fix setting thermal shutdown polarity
thermal: rockchip: fix handling of invalid readings
devfreq_cooling: add trace information
thermal: Add devfreq cooling
PM / OPP: get the voltage for all OPPs
tools/thermal: tmon: use pkg-config also for CFLAGS
linux/thermal.h: rename KELVIN_TO_CELSIUS to DECI_KELVIN_TO_CELSIUS
...
Switch everything to the new and more capable implementation of abs().
Mainly to give the new abs() a bit of a workout.
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'ret' variable in exynos5440_tmu_initialize() is initialized to 0
and returned as is. Replace it with direct return statement. This also
fixes coccinelle warning:
drivers/thermal/samsung/exynos_tmu.c:611:5-8: Unneeded variable: "ret". Return "0" on line 654
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The NULL check in probe's error path is not needed because in that time
the regulator cannot be NULL (regulator_get() returns valid pointer or
ERR_PTR).
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal core could not read the temperature after registering the
thermal sensor with thermal_zone_of_sensor_register() because the driver
was not yet initialized.
The call trace looked like:
exynos_tmu_probe()
thermal_zone_of_sensor_register()
of_thermal_set_mode()
thermal_zone_device_update()
exynos_get_temp()
if (!data->tmu_read) return -EINVAL;
exynos_map_dt_data()
data->tmu_read = ...
This produced an error in dmesg:
thermal thermal_zone0: failed to read out thermal zone (-22)
Register the thermal_zone_device later, after parsing Device Tree and
enabling necessary clocks, but before calling exynos_tmu_initialize()
which uses the registered thermal_zone_device.
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 3b6a1a805f ("thermal: samsung: core: Exynos TMU rework to use device tree for configuration")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
During probe if the regulator could not be enabled, the error exit path
would still disable it. This could lead to unbalanced counter of
regulator enable/disable.
The patch moves code for getting and enabling the regulator from
exynos_map_dt_data() to probe function because it is really not a part
of getting Device Tree properties.
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 5f09a5cbd1 ("thermal: exynos: Disable the regulator on probe failure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If the allocation fails then we can't continue.
Fixes: a76caf55e5 ('thermal: Add devfreq cooling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When we come out of system suspend state (S3) the tsadc will have been
reset and back at its default state. While reprogramming the tsadc
it's possible that we'll glitch the output and unintentionally cause
the "over temperature" GPIO to be asserted. Since the over
temperature GPIO is often hooked up to something that will cause a
reboot or shutdown in hardware, this glitch can be catastrophic on
some boards.
We'll add support for selecting the "sleep" pinctrl state at suspend
time. Boards can use this to effectively disable the tsadc at suspend
time and avoid glitches when the system is resumed.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The prototype of do_div() is:
uint32_t do_div(uint64_t *n, uint32_t base);
Make power u64 to avoid the following warning:
drivers/thermal/devfreq_cooling.c: In function 'get_dynamic_power':
drivers/thermal/devfreq_cooling.c:267:2: warning: comparison of distinct pointer types lacks a cast [enabled by default]
drivers/thermal/devfreq_cooling.c:267:2: warning: right shift count >= width of type [enabled by default]
drivers/thermal/devfreq_cooling.c:267:2: warning: passing argument 1 of '__div64_32' from incompatible pointer type [enabled by default]
include/asm-generic/div64.h:35:17: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Be consistent with what other cooling devices do and return a struct
thermal_cooling_device * on register. Also, for the unregister, accept
a struct thermal_cooling_device * as parameter.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We recently changed this from unsigned long to int so it introduced an
underflow bug.
Fixes: 17e8351a77 ('thermal: consistently use int for temperatures')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Update the coefficients so the calculation will not overrun the
unsigned long 32bits boundary
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Victor Axelrod <victora@marvell.com>
Reviewed-by: Neta Zur Hershkovits <neta@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The irq handler should be registered after the tempmon
module has been initialized in a known state and the
thermal_zone and cpu_cooling device have been registered
successfully. Otherwise, if the irq is triggled earlier
before thermal probe has been finished, it may lead to
'NULL' pointer kernel panic.
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When requested thermal shutdown signal polarity is low we need to make
sure that the bit representing high level of signal is reset, and not
set all other bits in that register.
Also rename TSADCV2_INT_PD_CLEAR to TSADCV2_INT_PD_CLEAR_MASK to better
reflect its nature.
Acked-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We attempted to signal invalid code by returning -EAGAIN from
rk_tsadcv2_code_to_temp(), unfortunately the return value was stuffed
directly into the temperature pointer, potentially confusing upper
layers with temperature of -EINVAL.
Let's split temperature from error/success indicator to avoid such
confusion.
Also change the way we scan the temperature table to start with the 2nd
element so that we do not need to worry that we may reference out of
bounds element while doing binary search and keep checking that we end
up with 'mid' equal to 0 (since we are looking for the temperature that
would fall into interval between the 'mid' and 'mid - 1') .
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Tracing is useful for debugging and performance tuning. Add similar
traces to what's present in the cpu cooling device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a generic thermal cooling device for devfreq, that is similar to
cpu_cooling.
The device must use devfreq. In order to use the power extension of the
cooling device, it must have registered its OPPs using the OPP library.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Ørjan Eide <orjan.eide@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The value of emul_con was getting overwritten if the selected soc is
SOC_ARCH_EXYNOS5260. And so as a result we were reading from the wrong
register in the case of SOC_ARCH_EXYNOS5260.
Fixes: 488c7455d7 ("thermal: exynos: Add the support for Exynos5433 TMU")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
In the function cpufreq_get_requested_power, the memory allocated
for load_cpu is live within the function only. And after the
allocation it is immediately freed with devm_kfree. There is no
need to allocate memory for load_cpu with devm function so replace
devm_kcalloc with kcalloc and devm_kfree with kfree.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
After the commit "thermal: core: Add Kconfig option to enable writable
trips", by default the trips are read only. This cause user space thermal
controllers to poll for temperature as they can't set temperature
thresholds for getting a notification via uevents. These programs use RW
trip in a zone to register thresholds. Since we need to enable the new
config introduced by above commit to allow writable trips, selecting
CONFIG_THERMAL_WRITABLE_TRIP for x86 thermal drivers.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
During boot I get a div by zero Oops regression starting in v4.3-rc3.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add OMAP36xx support to ti-soc-thermal driver. This
chip is also unreliable. The data provided here is
based on OMAP36xx TRM:
http://www.ti.com/lit/ug/swpu177aa/swpu177aa.pdf
Signed-off-by: Eduardo Valentin <edubezva@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This adds support for OMAP3 chips to ti-soc-thermal. As requested by
TI people, it is marked unreliable and warning is printed.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Don't waste cycles in the power allocator governor's throttle function
if there are no cooling devices and exit early.
This commit doesn't change any functionality, but should provide better
performance for the odd case of a thermal zone with trip points but
without cooling devices.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal zones created using thermal_zone_device_create() may not have
tzp. As the governor gets its parameters from there, allocate it while
the governor is bound to the thermal zone so that it can operate in it.
In this case, tzp is freed when the thermal zone switches to another
governor.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power allocator governor currently requires that the thermal zone
has at least two passive trip points. If there aren't, the governor
refuses to bind to the thermal zone.
This commit relaxes that requirement. Now the governor will bind to all
thermal zones regardless of how many trip points they have.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power allocator governor currently requires that a sustainable power
is passed as part of the thermal zone's thermal zone parameters. If
that parameter is not provided, it doesn't register with the thermal
zone.
While this parameter is strongly recommended for optimal performance, it
doesn't need to be mandatory. Relax the requirement and allow the
governor to bind to thermal zones that don't provide it by estimating it
from the cooling devices' power model.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal core already has a function to get the maximum power of a
cooling device: power_actor_get_max_power(). Add a function to get the
minimum power of a cooling device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power table is not being freed on error from cpufreq_cooling
register or when unregistering. Free it.
Fixes: c36cf07176 ("thermal: cpu_cooling: implement the power cooling device API")
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
build_dyn_power_table() allocates the power table while holding
rcu_read_lock. kcalloc using GFP_KERNEL may sleep, so it can't be
called in an RCU read-side path.
Move the rcu protection to the part of the function that really needs
it: the part that handles the dev_pm_opp pointer received from
dev_pm_opp_find_freq_ceil(). In the unlikely case that there is an OPP
added to the cpu while this function is running, return -EAGAIN.
Fixes: c36cf07176 ("thermal: cpu_cooling: implement the power cooling device API")
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
I didn't notice this when merging the thermal code from Zhang, but his
merge (commit 5a924a07f8: "Merge branches 'thermal-core' and
'thermal-intel' of .git into next") of the thermal-core and
thermal-intel branches was wrong.
In thermal-core, commit 17e8351a77 ("thermal: consistently use int for
temperatures") converted the thermal layer to use "int" for
temperatures.
But in parallel, in the thermal-intel branch commit d0a12625d2
("thermal: Add Intel PCH thermal driver") added support for the intel
PCH thermal sensor using the old interfaces that used "unsigned long"
pointers.
This resulted in warnings like this:
drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_temp = pch_thermal_get_temp,
^
drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’)
drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_trip_temp = pch_get_trip_temp,
^
drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’)
This fixes it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
This has been a busy release for regmap. By far the biggest set of
changes here are those from Markus Pargmann which implement support for
block transfers in smbus devices. This required quite a bit of
refactoring but leaves us better able to handle odd restrictions that
controllers may have and with better performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV6cZyAAoJECTWi3JdVIfQM3sH/RSygzRIOoOuvro0U3qd4+nM
qLzpuZNtuAP7xNc5yJZiixz1S6PqUNl+pK/u58s6x10GWDGsWZY6E0Lg94lYmfhA
26jqWSzrMHp42x+ZN7btLExzPTVnvRerrjtj4mqz6t4yun9SzqVymaZTUZ1hqPHB
qxSNHs3rHPiqiEWpQKJXb+5dazYYJCbOUrlivxJCk60+ns1N88cA71aY+5/zq5uy
36e0iYe3s+lv0lptedarFCf9p7o1E6EQzhvEMfyquGXtvq8fl7Qdeo7riRFQ8Iiy
sygCb3AYuZIiqnOC7+90xkr2Oq0iwdJUD91A9sl/SRiwgItG9jW03bWNHYIhQyk=
=CbGt
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a busy release for regmap.
By far the biggest set of changes here are those from Markus Pargmann
which implement support for block transfers in smbus devices. This
required quite a bit of refactoring but leaves us better able to
handle odd restrictions that controllers may have and with better
performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald"
* tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (25 commits)
regmap: fix a NULL pointer dereference in __regmap_init
regmap: Support bulk reads for devices without raw formatting
regmap-i2c: Add smbus i2c block support
regmap: Add raw_write/read checks for max_raw_write/read sizes
regmap: regmap max_raw_read/write getter functions
regmap: Introduce max_raw_read/write for regmap_bulk_read/write
regmap: Add missing comments about struct regmap_bus
regmap: No multi_write support if bus->write does not exist
regmap: Split use_single_rw internally into use_single_read/write
regmap: Fix regmap_bulk_write for bus writes
regmap: regmap_raw_read return error on !bus->read
regulator: core: Print at debug level on debugfs creation failure
regmap: Fix regmap_can_raw_write check
regmap: fix typos in regmap.c
regmap: Fix integertypes for register address and value
regmap: Move documentation to regmap.h
regmap: Use different lockdep class for each regmap init call
thermal: sti: Add parentheses around bridge->ops->regmap_init call
mfd: vexpress: Add parentheses around bridge->ops->regmap_init call
regmap: debugfs: Fix misuse of IS_ENABLED
...
Pull x86 asm changes from Ingo Molnar:
"The biggest changes in this cycle were:
- Revamp, simplify (and in some cases fix) Time Stamp Counter (TSC)
primitives. (Andy Lutomirski)
- Add new, comprehensible entry and exit handlers written in C.
(Andy Lutomirski)
- vm86 mode cleanups and fixes. (Brian Gerst)
- 32-bit compat code cleanups. (Brian Gerst)
The amount of simplification in low level assembly code is already
palpable:
arch/x86/entry/entry_32.S | 130 +----
arch/x86/entry/entry_64.S | 197 ++-----
but more simplifications are planned.
There's also the usual laudry mix of low level changes - see the
changelog for details"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (83 commits)
x86/asm: Drop repeated macro of X86_EFLAGS_AC definition
x86/asm/msr: Make wrmsrl() a function
x86/asm/delay: Introduce an MWAITX-based delay with a configurable timer
x86/asm: Add MONITORX/MWAITX instruction support
x86/traps: Weaken context tracking entry assertions
x86/asm/tsc: Add rdtscll() merge helper
selftests/x86: Add syscall_nt selftest
selftests/x86: Disable sigreturn_64
x86/vdso: Emit a GNU hash
x86/entry: Remove do_notify_resume(), syscall_trace_leave(), and their TIF masks
x86/entry/32: Migrate to C exit path
x86/entry/32: Remove 32-bit syscall audit optimizations
x86/vm86: Rename vm86->v86flags and v86mask
x86/vm86: Rename vm86->vm86_info to user_vm86
x86/vm86: Clean up vm86.h includes
x86/vm86: Move the vm86 IRQ definitions to vm86.h
x86/vm86: Use the normal pt_regs area for vm86
x86/vm86: Eliminate 'struct kernel_vm86_struct'
x86/vm86: Move fields from 'struct kernel_vm86_struct' to 'struct vm86'
x86/vm86: Move vm86 fields out of 'thread_struct'
...
Commit cf736ea6f9 ("thermal: power_allocator: do not use devm*
interfaces") forgot to change a devm_kcalloc() to just kcalloc(), but
it's corresponding devm_kfree() was changed to kfree(). Allocate with
kcalloc() to match the kfree().
Fixes: cf736ea6f9 ("thermal: power_allocator: do not use devm* interfaces")
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
policy->max is the maximum allowed frequency defined by user and
clipped_freq is the maximum that thermal constraints allow.
If clipped_freq is lower than policy->max, then we need to readjust
policy->max.
But, if clipped_freq is greater than policy->max, we don't need to do
anything. We used to call cpufreq_verify_within_limits() in this case,
but it doesn't change anything in this case.
Lets skip this unnecessary call and write a comment that explains this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
That's what it is for, lets name it properly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
That's what it is for, lets name it properly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We just need to take care of single event here and there is no need to
increase indentation level of most of the code (which causes lines
longer that 80 columns to break).
Kill the switch block.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If a valid cpufreq_dev is found for policy->cpu, we should update the
policy and quit the for loop. There is no need to keep traversing the
list of cpufreq_dev's.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Its always set before getting used, don't initialize it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The code in question is called outside of standard driver
probe()/remove() callbacks and thus will not benefit from use of devm*
infrastructure.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
regmap_init(...) is a macro since commit
"regmap: Use different lockdep class for each regmap init call".
That same name is used as a function pointer: prevent its expansion
by adding parentheses around the function pointer.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change adds a thermal driver for Wildcat Point platform controller
hub. This driver register PCH thermal sensor as a thermal zone and
associate critical and hot trips if present.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The code testing if a temperature should be emulated or not is
not obvious. Add a comment explaining why this test is done.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use IS_ENABLED(CONFIG_THERMAL_EMULATION) to make the code more readable
and to get rid of the addtional #ifdef around the variable definitions
in thermal_zone_get_temp().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When the thermal zone has no get_temp callback then thermal_zone_device_register()
calls thermal_zone_device_set_polling() with a polling delay of 0. This
only cancels the poll_queue. Since the poll_queue hasn't been scheduled this
is a no-op. Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The Linux thermal framework support to change thermal governor
policy in userspace, but it can't show what available policies
supported.
This patch adds available_policies attribute to the thermal
framework, it can list the thermal governors which can be
used for a particular zone. This attribute is read only.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add support for Intel Denlow UP server platform.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The exynos thermal driver use the of_thermal_*() API to parse the basic data
for thermal management from devicetree file. So, if CONFIG_EXYNOS_THERMAL is
selected without CONFIG_THERMAL_OF, kernel can build it without any problem.
But, exynos thermal driver is not working with following error log. This patch
add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF.
[ 1.458644] get_th_reg: Cannot get trip points from of-thermal.c!
[ 1.459096] get_th_reg: Cannot get trip points from of-thermal.c!
[ 1.465211] exynos4412_tmu_initialize: No CRITICAL trip point defined at of-thermal.c!
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
During probe the regulator (if present) was enabled but not disabled in
case of failure. So an unsuccessful probe lead to enabling the
regulator which was actually not needed because the device was not
enabled.
Additionally each deferred probe lead to increase of regulator enable
count so it would not be effectively disabled during removal of the
device.
Test HW: Exynos4412 - Trats2 board
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 498d22f616 ("thermal: exynos: Support for TMU regulator defined at device tree")
Cc: <stable@vger.kernel.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power allocator governor uses ftrace to output a bunch of internal
data for debugging and tuning. Currently, the requested power it
outputs is the "weighted" requested power, that is, what each cooling
device has requested multiplied by the cooling device weight. It is
more useful to trace the real request, without any weight being
applied.
This commit only affects the data traced, there is no functional change.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that the ->read_tsc() paravirt hook is gone, rdtscll() is
just a wrapper around native_read_tsc(). Unwrap it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/d2449ae62c1b1fb90195bcfb19ef4a35883a04dc.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Pull thermal management updates from Zhang Rui:
"Specifics:
- enhance Thermal Framework with several new capabilities:
* use power estimates
* compute weights with relative integers instead of percentages
* allow governors to have private data in thermal zones
* export thermal zone parameters through sysfs
Thanks to the ARM thermal team (Javi, Punit, KP).
- introduce a new thermal governor: power allocator. First in kernel
closed loop PI(D) controller for thermal control. Thanks to ARM
thermal team.
- enhance OF thermal to allow thermal zones to have sustainable power
HW specification. Thanks to Punit.
- introduce thermal driver for Intel Quark SoC x1000platform. Thanks
to Ong, Boon Leong.
- introduce QPNP PMIC temperature alarm driver. Thanks to Ivan T. I.
- introduce thermal driver for Hisilicon hi6220. Thanks to
kongxinwei.
- enhance Exynos thermal driver to handle Exynos5433 TMU. Thanks to
Chanwoo C.
- TI thermal driver now has a better implementation for EOCZ bit.
From Pavel M.
- add id for Skylake processors in int340x processor thermal driver.
- a couple of small fixes and cleanups."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
thermal: hisilicon: add new hisilicon thermal sensor driver
dt-bindings: Document the hi6220 thermal sensor bindings
thermal: of-thermal: add support for reading coefficients property
thermal: support slope and offset coefficients
thermal: power_allocator: round the division when divvying up power
thermal: exynos: Add the support for Exynos5433 TMU
thermal: cpu_cooling: Fix power calculation when CPUs are offline
thermal: cpu_cooling: Remove cpu_dev update on policy CPU update
thermal: export thermal_zone_parameters to sysfs
thermal: cpu_cooling: Check memory allocation of power_table
ti-soc-thermal: request temperature periodically if hw can't do that itself
ti-soc-thermal: implement eocz bit to make driver useful on omap3
cleanup ti-soc-thermal
thermal: remove stale THERMAL_POWER_ACTOR select
thermal: Default OF created trip points to writable
thermal: core: Add Kconfig option to enable writable trips
thermal: x86_pkg_temp: drop const for thermal_zone_parameters
of: thermal: Introduce sustainable power for a thermal zone
thermal: add trace events to the power allocator governor
thermal: introduce the Power Allocator governor
...
This patch adds the support for hisilicon thermal sensor, within
hisilicon SoC. there will register sensors for thermal framework
and use device tree to bind cooling device.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: kongxinwei <kong.kongxinwei@hisilicon.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In order to avoid having each driver adding their own
specific DT property to specify slope and offset,
this patch adds a basic coefficient reading from
DT thermal zone node. Right now, as the thermal
framework does not support multiple sensors,
the current coefficients apply only to the only
sensor in the thermal zone.
The supported equation is a simple linear model:
slope * <sensor reading> + offset.
slope and offset are read from the coefficients
DT property. In the same way as it is described in
the DT thermal binding.
So, as of today, the thermal framework will support
only cases like:
/* hotspot = 1 * adc + 6000 */
coefficients = <1 6000>;
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It is common to have a linear extrapolation from
the current sensor readings and the actual temperature
value. This is specially the case when the sensor
is in use to extrapolate hotspots.
This patch adds slope and offset constants for
single sensor linear extrapolation equation. Because
the same sensor can be use in different locations,
from board to board, these constants are added
as part of thermal_zone_params.
The constants are available through sysfs.
It is up to the device driver to determine
the usage of these values.
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In situations where there is an uneven number of cooling devices, the
division of power among them can lead to a milliwatt being dropped on
the floor due to rounding errors. This doesn't sound like a lot, but
some devices only grant the lowest cooling device state for their
maximum power. So for instance, if the granted_power is the maximum
power and all devices are getting their maximum power, one would get
max_power - 1, making it choose cooling device state 1, instead of 0.
Round the division to make the calculation more accurate.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is a copy and paste bug, "->clk" vs "->pclk", so we return the
wrong error code here.
Fixes: cbac8f6394 ('thermal: rockchip: add driver for thermal')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Package C8 to C10 was introduced in newer Intel CPUs, we need to
include them in the package c-state residency calculation.
Otherwise, idle injection target is not accurately maintained by
the closed control loop.
Also cleaned up the code to make it scale better with large number
of c-states.
Reported-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Broadwell server has support for package C-states, idle injection works
as expected on this platform.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Mark the module init / exit functions with __init / __exit accodingly.
This allows making the intel_powerclamp_ids[] array __initconst, too, as
it only gets referenced from powerclamp_probe(). This is safe as
file2alias doesn't care about the section, but the symbol name for the
MODULE_DEVICE_TABLE alias.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
DESCRIPTION
Spurious Thermal Alert: Talert can happen randomly while the device remains
under the temperature limit defined for this event to trig. This spurious
event is caused by a incorrect re-synchronization between clock domains.
The comparison between configured threshold and current temperature value
can happen while the value is transitioning (metastable), thus causing
inappropriate event generation. No spurious event occurs as long as the
threshold value stays unchanged. Spurious event can be generated while a
thermal alert threshold is modified in
CONTROL_BANDGAP_THRESHOLD_MPU/GPU/CORE/DSPEVE/IVA_n.
WORKAROUND
Spurious event generation can be avoided by performing following sequence
when the threshold is modified:
1. Mask the hot/cold events at the thermal IP level.
2. Modify Threshold.
3. Unmask the hot/cold events at the thermal IP level.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Bandgap Temperature read Dtemp can be corrupted
DESCRIPTION
Read accesses to registers listed below can be corrupted due to
incorrect resynchronization between clock domains.
Read access to registers below can be corrupted :
• CTRL_CORE_DTEMP_MPU/GPU/CORE/DSPEVE/IVA_n (n = 0 to 4)
• CTRL_CORE_TEMP_SENSOR_MPU/GPU/CORE/DSPEVE/IVA_n
WORKAROUND
Multiple reads to CTRL_CORE_TEMP_SENSOR_MPU/GPU/CORE/DSPEVE/IVA[9:0]:
BGAP_DTEMPMPU/GPU/CORE/DSPEVE/IVA is needed to discard false value and
read right value:
1. Perform two successive reads to BGAP_DTEMP bit field.
(a) If read1 returns Val1 and read2 returns Val1, then
right value is Val1.
(b) If read1 returns Val1, read 2 returns Val2, a third
read is needed.
2. Perform third read
(a) If read3 returns Val2 then right value is Val2.
(b) If read3 returns Val3, then right value is Val3.
The above in gist means if val1 and val2 are the same then we can go
ahead with that value else we need a third read which will be right
since synchronization will be complete by then.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch adds the support for Exynos5433's TMU (Thermal Management Unit).
Exynos5433 has a little different register bit fields as following description:
- Support the eight trip points for rising/falling interrupt by using two registers
- Read the calibration type (1-point or 2-point) and sensor id from TRIMINFO register
- Use a little different register address
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Ensure that the CPU for which the frequency is being requested
is online. If none of the CPUs are online the requested power is
returned as 0.
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It was initially understood that an update to the cpu_device
(cached in cpufreq_cooling_device) was required to ascertain the
correct operating point of the device on a cpufreq policy->cpu update
or creation or deletion of a cpufreq policy.
(e.g. when the existing policy CPU goes offline).
This update is not required and it is possible to ascertain the OPPs
from the leading CPU in a cpufreq domain even if the CPU is hotplugged out.
Fixes: e0128d8ab423 ("thermal: cpu_cooling: implement the power cooling device API")
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It's useful for tuning to be able to edit thermal_zone_parameters from
userspace. Export them to the thermal_zone sysfs so that they can be
easily changed.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We allocate the power_table in memory but we don't test whether the
allocation succeeded. Return -ENOMEM if kcalloc() fails.
Fixes: e0128d8ab423 ("thermal: cpu_cooling: implement the power cooling device API")
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When periodic mode is not enabled, it is neccessary to force reads.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
For omap3, proper implementation of eocz bit is needed. It was
actually a TODO in the driver.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Simplify code by removing goto's where they point to simple return.
Avoid confusing |= on error values.
Correct whitespace.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
A previous version of this patch had a config for THERMAL_POWER_ACTOR
but it was dropped. Remove the select as it is not doing anything.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When registering a thermal zone from device tree, default the trip
points to writable. By default, only the root user can change these.
This allows the trip points to be tweaked after the system has
booted.
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a Kconfig option to allow system integrators to control whether
userspace tools can change trip temperatures. This option overrides
the thermal zone setup in the driver code and must be enabled for
platform specified writable trips to come into effect.
The original behaviour of requiring root privileges to change trip
temperatures remains unchanged.
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
8754d5115693 ("thermal: introduce the Power Allocator governor") dropped
the const attribute in the struct thermal_zone_device. That means that
the thermal_zone_params pointer passed to thermal_zone_device_register()
also lost the const qualifier. Drop the const in x86_pkg_temp_thermal.c
as well to avoid the following warning as reported by the kbuild test
robot:
drivers/thermal/x86_pkg_temp_thermal.c: In function 'pkg_temp_thermal_device_add':
>> drivers/thermal/x86_pkg_temp_thermal.c:450:31: warning: passing argument 6 of 'thermal_zone_device_register' discards 'const' qualifier from pointer target type
phy_dev_entry, &tzone_ops, &pkg_temp_tz_params, 0, 0);
^
In file included from drivers/thermal/x86_pkg_temp_thermal.c:30:0:
include/linux/thermal.h:378:29: note: expected 'struct thermal_zone_params *' but argument is of type 'const struct thermal_zone_params *'
struct thermal_zone_device *thermal_zone_device_register(const char *, int, int,
^
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Introduce an optional property called, sustainable-power, which
represents the power (in mW) which the thermal zone can safely
dissipate.
If provided the property is parsed and associated with the thermal
zone via the thermal zone parameters.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add trace events for the power allocator governor and the power actor
interface of the cpu cooling device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power allocator governor is a thermal governor that controls system
and device power allocation to control temperature. Conceptually, the
implementation divides the sustainable power of a thermal zone among
all the heat sources in that zone.
This governor relies on "power actors", entities that represent heat
sources. They can report current and maximum power consumption and
can set a given maximum power consumption, usually via a cooling
device.
The governor uses a Proportional Integral Derivative (PID) controller
driven by the temperature of the thermal zone. The output of the
controller is a power budget that is then allocated to each power
actor that can have bearing on the temperature we are trying to
control. It decides how much power to give each cooling device based
on the performance they are requesting. The PID controller ensures
that the total power budget does not exceed the control temperature.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a basic power model to the cpu cooling device to implement the
power cooling device API. The power model uses the current frequency,
current load and OPPs for the power calculations. The cpus must have
registered their OPPs using the OPP library.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add three optional callbacks to the cooling device interface to allow
them to express power. In addition to the callbacks, add helpers to
identify cooling devices that implement the power cooling device API.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
A governor may need to store its current state between calls to
throttle(). That state depends on the thermal zone, so store it as
private data in struct thermal_zone_device.
The governors may have two new ops: bind_to_tz() and unbind_from_tz().
When provided, these functions let governors do some initialization
and teardown when they are bound/unbound to a tz and possibly store that
information in the governor_data field of the struct
thermal_zone_device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support for the temperature alarm peripheral found inside
Qualcomm plug-and-play (QPNP) PMIC chips. The temperature alarm
peripheral outputs a pulse on an interrupt line whenever the
thermal over temperature stage value changes.
Register a thermal sensor. The temperature reported by this thermal
sensor device should reflect the actual PMIC die temperature if an
ADC is present on the given PMIC. If no ADC is present, then the
reported temperature should be estimated from the over temperature
stage value.
Cc: David Collins <collinsd@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The fair share governor has the concept of weights, which is the
influence of each cooling device in a thermal zone. The current
implementation forces the weights of all cooling devices in a thermal
zone to add up to a 100. This complicates setups, as you need to know
in advance how many cooling devices you are going to have. If you bind a
new cooling device, you have to modify all the other cooling devices
weights, which is error prone. Furthermore, you can't specify a
"default" weight for platforms since that default value depends on the
number of cooling devices in the platform.
This patch generalizes the concept of weight by allowing any number to
be a "weight". Weights are now relative to each other. Platforms that
don't specify weights get the same default value for all their cooling
devices, so all their cdevs are considered to be equally influential.
It's important to note that previous users of the weights don't need to
alter the code: percentages continue to work as they used to. This
patch just removes the constraint of all the weights in a thermal zone
having to add up to a 100. If they do, you get the same behavior as
before. If they don't, fair share now works for that platform.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It's useful to have access to the weights for the cooling devices for
thermal zones and change them if needed. Export them to sysfs.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The fair share governor is not usable with thermal zones that use the
bind op and don't populate thermal_zone_parameters, the majority of
them. Now that the weight is in the thermal instance, we can use that
in the fair share governor to allow every thermal zone to trivially use
this governor. Furthermore, this simplifies the code.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently you can specify the weight of the cooling device in the device
tree but that information is not populated to the
thermal_bind_params where the fair share governor expects it to
be. The of thermal zone device doesn't have a thermal_bind_params
structure and arguably it's better to pass the weight inside the
thermal_instance as it is specific to the bind of a cooling device to a
thermal zone parameter.
Core thermal code is fixed to populate the weight in the instance from
the thermal_bind_params, so platform code that was passing the weight
inside the thermal_bind_params continue to work seamlessly.
While we are at it, create a default value for the weight parameter for
those thermal zones that currently don't define it and remove the
hardcoded default in of-thermal.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Peter Feuerer <peter@piie.net>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch enables intel_powerclamp driver to run on the
next-generation Intel(R) Xeon Phi Microarchitecture
code named "Knights Landing"
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
drivers/thermal/intel_soc_dts_iosf.c:358:4-7: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS).
The DTS offers both hot & critical trip points.
However, in current distribution of UEFI BIOS for Quark platform, only
critical trip point is configured to be 105 degree Celsius (based on Quark
SW ver1.0.1 and hot trip point is not used due to lack of IRQ.
There is no active cooling device for Quark SoC, so Quark SoC thermal
management logic expects Linux distro to orderly power-off when temperature
of the DTS exceeds the configured critical trip point.
Kernel param "polling_delay" in milliseconds is used to control the frequency
the DTS temperature is read by thermal framework. It defaults to 2-second.
To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X".
User interacts with Quark SoC DTS thermal driver through sysfs via:
/sys/class/thermal/thermal_zone0/
For example:
- to read DTS temperature
$ cat temp
- to read critical trip point
$ cat trip_point_0_temp
- to read trip point type
$ cat trip_point_0_type
- to emulate temperature raise to test orderly shutdown by Linux distro
$ echo 105 > emul_temp
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Support two auxiliary DTS present on Braswell platform using side band
IOSF interface. This supports two read write trips, which can be used
to get notification on trip violation.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
There is no change in functionality but using the common IOSF core APIs.
This driver is now just responsible for enumeration and call relevant
API to create thermal zone and register critical trip.
Also cpuid 0x4c is now handled in the int340x processor thermal driver
with the same functionality.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
This is becoming a common feature for Intel SoCs to expose the additional
digital temperature sensors (DTSs) using side band interface (IOSF). This
change remove common IOSF DTS handler function from the existing driver
intel_soc_dts_thermal.c and creates a stand alone module, which can
be selected from the SoC specific drivers. In this way there is less
code duplication.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Simple patch to make symbols static. Symbols that are not
shared with other parts of the kernel can be made static.
This change also removes several sparse complains.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ajit Pal Singh <ajitpal.singh@st.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Some temperature sensors only get updated every few seconds and while
waiting for the first irq reporting a (new) temperature to happen there
get_temp operand will return -EAGAIN as it does not have any data to report
yet.
Not logging an error in this case avoids messages like these from showing
up in dmesg on affected systems:
[ 1.219353] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.015433] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.416737] thermal thermal_zone0: failed to read out thermal zone 0
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Default attributes are created when the device is registered. Attributes
created after device registration can lead to race conditions, where user space
(e.g. udev) sees the device but not the attributes.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When thermal zone device register fails or on module exit, the memory
for aux_trip is not freed. This change fixes this issue.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch fixes the wrong control of PD_DET_EN (power down detection mode)
for Exynos7 because exynos7_tmu_control() always enables the power down detection
mode regardless 'on' parameter.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
It is possible that _ART/_TRT tables are missing or have errors.
Ignore those failures, as INT3400 thermal zone is still required
for _OSC or mode switch.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enable Intel Powerclamp driver on Atom* Processor C2000 Product
Family for Microservers (Avoton). Avoton - SoCs for micro-servers
has package C-states which can be used for idle injection.
Reported-by: Jose Navarro <jose.navarro@intel.com>
Suggested-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Tested-by: Jose Carlos Venegas Munoz <jos.c.venegas.munoz@intel.com>
Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Swap interrupt disable and thermal zone unregistration in the error and
remove paths, to make them more symmetrical with the initialization
path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As soon as the interrupt has been enabled by devm_request_irq(), the
interrupt routine may be called, depending on the current status of the
hardware.
However, at that point rcar_thermal_common hasn't been initialized
complely yet. E.g. rcar_thermal_common.base is still NULL, causing a
NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
pgd = c0004000
[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc7-ape6evm-04564-gb6e46cb7cbe82389 #30
Hardware name: Generic R8A73A4 (Flattened Device Tree)
task: ee8953c0 ti: ee896000 task.ti: ee896000
PC is at rcar_thermal_irq+0x1c/0xf0
LR is at _raw_spin_lock_irqsave+0x48/0x54
Postpone the call to devm_request_irq() until all initialization has
been done to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The cpufreq_cooling_unregister() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Fix following build warning if CONFIG_PM_SLEEP is not set:
drivers/thermal/ti-soc-thermal/ti-bandgap.c:1478:12: warning: 'ti_bandgap_suspend' defined but not used [-Wunused-function]
static int ti_bandgap_suspend(struct device *dev)
^
drivers/thermal/ti-soc-thermal/ti-bandgap.c:1492:12: warning: 'ti_bandgap_resume' defined but not used [-Wunused-function]
static int ti_bandgap_resume(struct device *dev)
^
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The exynos_tmu_data() function should on entrance test not only for valid
data pointer, but also for data->tmu_read one.
It is important, since afterwards it is dereferenced to get temperature code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull more thermal managament updates from Zhang Rui:
"Specifics:
- Exynos thermal driver refactoring. Several cleanups, code
optimization, unused symbols removal, and unused feature removal in
Exynos thermal driver. Thanks Lukasz for this effort.
- Exynos thermal driver support to OF thermal. After the code
refactoring, the driver earned the support to OF thermal. Chip
thermal data were moved from driver code to DTS, reducing the code
footprint. Thanks Lukasz for this.
- After receiving the OF thermal support, the exynos thermal driver
now must allow modular build. Thanks Arnd for detecting, reporting
and fixing this.
- Exynos thermal driver support to Exynos 7 SoC. Thanks Abhilash for
this.
- Accurate temperature reporting on Rockchip thermal driver, thanks
to Caesar.
- Fix on how OF thermal enables its zones, thanks Lukasz for fixing.
- Fixes in OF thermal examples under Documentation/. Thanks Srinivas
for fixing"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: exynos: Add TMU support for Exynos7 SoC
dts: Documentation: Add documentation for Exynos7 SoC thermal bindings
cpufreq: exynos: allow modular build
thermal: Fix examples in DT documentation
thermal: exynos: Correct sanity check at exynos_report_trigger() function
thermal: Kconfig: Remove config for not used EXYNOS_THERMAL_CORE
thermal: exynos: Remove exynos_tmu_data.c file
thermal: rockchip: make temperature reporting much more accurate
thermal: exynos: Remove exynos_thermal_common.[c|h] files
thermal: samsung: core: Exynos TMU rework to use device tree for configuration
dts: Documentation: Update exynos-thermal.txt example for Exynos5440
dts: Documentation: Extending documentation entry for exynos-thermal
cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered
thermal: exynos: Modify exynos thermal code to use device tree for cpu cooling configuration
thermal: exynos: Provide thermal_exynos.h file to be included in device tree files
thermal: exynos: cosmetic: Correct comment format
thermal: of: Enable thermal_zoneX when sensor is correctly added
Pull thermal managament updates from Zhang Rui:
"Specifics:
- Abstract the code and introduce helper functions for all int340x
thermal drivers. From: Srinivas Pandruvada.
- Reorganize the ACPI LPAT table support code so that it can be
shared for both ACPI PMIC driver and int340x thermal driver.
- Add support for Braswell in intel_soc_dts thermal driver.
- a couple of small fixes/cleanups for step_wise governor and int340x
thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Thermal/int340x_thermal: remove unused uuids.
thermal: step_wise: spelling fixes
thermal: int340x: fix sparse warning
Thermal/int340x: LPAT conversion for temperature
ACPI / PMIC: Use common LPAT table handling functions
ACPI / LPAT: Common table processing functions
thermal: Intel SoC DTS: Add Braswell support
Thermal/int340x/int3402: Provide notification support
Thermal/int340x/processor_thermal: Add thermal zone support
Thermal/int340x/int3403: Use int340x thermal API
Thermal/int340x/int3402: Use int340x thermal API
Thermal/int340x: Add common thermal zone handler
this patch fixes following sparse warning:
processor_thermal_device.c:188:6: warning: symbol 'proc_thermal_remove' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add registers, bit fields and compatible strings for Exynos7 TMU
(Thermal Management Unit). Following are a few of the differences
in the Exynos7 TMU from earlier SoCs:
- 8 trigger levels
- Different bit offsets and more registers for the rising
and falling thresholds.
- New power down detection bit in the TMU_CONTROL register
which does not update the CURRENT_TEMP0 when tmu power down
is detected.
- Change in bit offset for the NEXT_DATA field of EMUL_CON
register. EMUL_CON register address has also changed.
- INTSTAT and INTCLEAR registers present in earlier SoCs
have been combined into one INTPEND register. The register
address for INTCLEAR and INTPEND is also different.
- Since there are 8 rising/falling interrupts as against
at most 4 in earlier SoCs the INTEN bit offsets are different.
- Multiple probe support which is handled by a TMU_CONTROL1
register (No support for this in the current patch).
This patch adds special clock support required only for Exynos7. It
also updates the "code_to_temp" prototype as Exynos7 has 9 bit
code-temp mapping.
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When LPAT table is present, we need to convert raw temperature to
real temp using LPAT.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Added Intel Braswell CPU id for SOC DTS. Since this doesn't support
APIC IRQ, the driver is modified to have capability to not register
any modifiable trips.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Up till now, by mistake, wrong variable was tested against being NULL.
Since exynos_report_trigger() is always called with valid p pointer,
it is only necessary to check if a valid thermal zone device is passed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
After removing exynos_thermal_common.[c|h] files the CONFIG_EXYNOS_THERMA_CORE
is not needed anymore.
This patch removes this entry from Kconfig.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Data already present in the exynos_tmu_data.c file has been moved to the
appropriate device tree files.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In general, the kernel should report temperature readings exactly as
reported by the hardware. The cpu / gpu thermal driver works in 5 degree
increments,but we ought to do more accurate. The temperature will do
linear interpolation between the entries in the table.
Test= $md5sum /dev/zero &
$while true; do grep "" /sys/class/thermal/thermal_zone[1-2]/temp;
sleep .5; done
e.g. We can get the result as follows:
/sys/class/thermal/thermal_zone1/temp:39994
/sys/class/thermal/thermal_zone2/temp:39086
/sys/class/thermal/thermal_zone1/temp:39994
/sys/class/thermal/thermal_zone2/temp:39540
/sys/class/thermal/thermal_zone1/temp:39540
/sys/class/thermal/thermal_zone2/temp:39540
/sys/class/thermal/thermal_zone1/temp:39540
/sys/class/thermal/thermal_zone2/temp:39994
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
After defining all necessary Exynos data in the device tree and heavy
reusage of the of-thermal.c those files can be removed.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch brings support for providing configuration via device tree.
Previously this data has been hardcoded in the exynos_tmu_data.c file.
Such approach was not scalable and very often required copying the whole
data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Up till now exynos_tmu_data.c was used for storing CPU cooling configuration
data. Now the Exynos thermal core code uses device tree to get this data.
For this purpose generic thermal code for configuring CPU cooling was
used.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch is a preparatory patch to be able to read Exynos thermal
configuration from the device tree.
It turned out that DTC is not able to interpret enums properly and hence
it is necessary to #define those values explicitly.
For this reason the ./include/dt-bindings/thermal/thermal_exynos.h file
has been introduced.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Up till now the thermal_zone mode was by default "disabled". With this
patch the default behavior was changed to "enable".
One can read the mode at:
/sys/class/thermal/thermal_zone0/mode
Tested-by: Javi Merino <javi.merino@arm.com>
Reported-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Added thermal zones for processor thermal using APIs provided by
int340x thermal zone module.
Like other INT340x devices, processor thermal device can also contain
trip points and way to get temperature. On some platform there is
no ACPI _TMP method, in those platform using IA64 architecture MSRs to
get temperature.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Using APIs from int340x thermal zone module to add and remove thermal
zones.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Using APIs from int340x thermal zone module to add and remove thermal
zones.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Most of the processing for each int340x driver to add a thermal zone
is very similar and every driver has to duplicate code.
Created a common module, which exports API to add and remove zones.
In this way, we not only avoid duplicate code but also helps in
bug fixes and enhancements.
If for some driver default processing for thermal zone callback is
not enough they can overide individual callback.
The code for this driver is primarily copied from int3402_thermal.c.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull thermal fixes from Zhang Rui:
"Specifics:
- bogus type qualifier fix in OF thermal code.
- Minor fixes on imx and rcar thermal drivers.
- Update TI SoC thermal maintainer entry.
- Updated documentation of OF cpufreq cooling register"
* 'thermal-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: rcar: Spelling/grammar: s/drier use .../driver uses ...s/
thermal: rcar: change type of ctemp in rcar_thermal_update_temp()
thermal: rcar: fix ENR register value
Documentation: thermal: document of_cpufreq_cooling_register()
Thermal: imx: add clk disable/enable for suspend/resume
MAINTAINERS: update ti-soc-thermal status
MAINTAINERS: Add linux-omap to list of reviewers for TI Thermal
thermal: of: Remove bogus type qualifier for of_thermal_get_trip_points()
Since the ctemp is used for rcar_thermal_write() in
rcar_thermal_update_temp(), the type of 'ctemp' should be "u32" instead
of "int". This patch also changes type of the helper variables 'old'
and 'new'.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
On R-Mobile APE6, since it has 3 thermal zones, ENR register
has enable bits in bit 19-16, bit 11-8 and bit 3-0.
However, on R-Car gen2, since it has 1 thermal zone, ENR register has
enable bits in bit 3-0. (In other words, the write value should always
be 0 for bit 31-4 of ENR register.)
So, this patch fixes the ENR register value using I/O resource sets.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal sensor's clk is from pll3_usb_otg, per hardware
design requirement, need to make sure pll3_usb_otg is disabled
before STOP mode is entered, otherwise, all PFDs under it may
enter incorrect state, this patch disables pll3_usb_otg before
suspend and enables it after resume.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
there is no ACPI device object
processor_thermal_device driver needs ACPI support to work. Thus, the driver
probing should fail when there is no ACPI device object asscociated.
This fixes a NULL pointer dereference when the driver is loaded
with INT340X feature disabled in BIOS.
Reported-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Chen Yu <yu.c.chen@intel.com>
For some INT340X thermal devices, even if they are not referred in
_TRT/_ART table, they still can be used by userspace for thermal control.
Thus change the code to enumerated all the INT340X devices,
no matter if they're referred in _TRT/_ART or not.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
With gcc 4.1.2, 4.2, and 4.2.4 (4.4 and later are OK):
drivers/thermal/thermal_core.h:110: warning: type qualifiers ignored on function return type
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: ce8be77859 ("thermal: of: Extend of-thermal to export table of trip points")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The Int340x thermal provides a processor thermal device, which
is used to control processor thermal states. These devices are
either reported as a PCI device or an ACPI device. This
device provides power limits, control states and optional
temperature.
This change implements minimal requirements to expose processor
power limits which can be used during thermal power limiting.
Power limits are exposed via an attribute group called
"power_limits" under the device. The exported attributes
are:
power_limit_0_max_uw
power_limit_1_max_uw
power_limit_0_min_uw
power_limit_1_min_uw
power_limit_0_tmin_us
power_limit_1_tmin_us
power_limit_0_tmax_us
power_limit_1_tmax_us
power_limit_0_step_uw
power_limit_1_step_uw
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The node field of struct cpufreq_cooling_device was reintroduced in
2dcd851fe4 (thermal: cpu_cooling: Update always cpufreq policy with
thermal constraints) but without the documentation that it once had.
Add it back so that all the fields of struct cpufreq_cooling_device
are documented.
Cc: Yadwinder Singh Brar <yadi.brar@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enable Intel Powerclamp driver on Xeon cpu id 0x56, package C-state
is available on this CPU for idle injection.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
If either of the entries was missing, the driver tried to free memory
using uninitialized pointer. In addition, it was dereferencing null
pointer.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull NOHZ update from Thomas Gleixner:
"Remove the call into the nohz idle code from the fake 'idle' thread in
the powerclamp driver along with the export of those functions which
was smuggeled in via the thermal tree. People have tried to hack
around it in the nohz core code, but it just violates all rightful
assumptions of that code about the only valid calling context (i.e.
the proper idle task).
The powerclamp trainwreck will still work, it just wont get the
benefit of long idle sleeps"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/powerclamp: Remove tick_nohz_idle abuse
commit 4dbd27711c "tick: export nohz tick idle symbols for module
use" was merged via the thermal tree without an explicit ack from the
relevant maintainers.
The exports are abused by the intel powerclamp driver which implements
a fake idle state from a sched FIFO task. This causes all kinds of
wreckage in the NOHZ core code which rightfully assumes that
tick_nohz_idle_enter/exit() are only called from the idle task itself.
Recent changes in the NOHZ core lead to a failure of the powerclamp
driver and now people try to hack completely broken and backwards
workarounds into the NOHZ core code. This is completely unacceptable
and just papers over the real problem. There are way more subtle
issues lurking around the corner.
The real solution is to fix the powerclamp driver by rewriting it with
a sane concept, but that's beyond the scope of this.
So the only solution for now is to remove the calls into the core NOHZ
code from the powerclamp trainwreck along with the exports.
Fixes: d6d71ee4a1 "PM: Introduce Intel PowerClamp Driver"
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Pan Jacob jun <jacob.jun.pan@intel.com>
Cc: LKP <lkp@01.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1412181110110.17382@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull thermal management update from Zhang Rui:
"Summary:
- of-thermal extension to allow drivers to register and use its
functionality in a better way, without exploiting thermal core.
From Lukasz Majewski.
- Fix a bug in intel_soc_dts_thermal driver which calls a sleep
function in interrupt handler. From Maurice Petallo.
- add a thermal UAPI header file for exporting the thermal generic
netlink information to user-space. From Florian Fainelli.
- First round of refactoring in Exynos driver. Bartlomiej and Lukasz
are attempting to make it lean and easier to understand.
- New thermal driver for Rockchip (rk3288), with support for DT
thermal. From Caesar Wang.
- New thermal driver for Nvidia, Tegra124 SOCTHERM driver, with
support for DT thermal. From Mikko Perttunen.
- New cooling device, based on common clock framework. From Eduardo
Valentin.
- a couple of small fixes in thermal core framework. From Srinivas
Pandruvada, Javi Merino, Luis Henriques.
- Dropping Armada A375-Z1 SoC thermal support as the chip is not in
the market, armada folks decided to drop its support.
- a couple of small fixes and cleanups in int340x thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (58 commits)
thermal: provide an UAPI header file
Thermal/int340x: Clear the error value of the last acpi_bus_get_device() call
thermal/powerclamp: add id for braswell cpu
thermal: Intel SoC DTS: Don't do thermal zone update inside spin_lock
Thermal: fix platform_no_drv_owner.cocci warnings
Thermal/int340x: avoid unnecessary pointer casting
thermal: int3403: Delete a check before thermal_zone_device_unregister()
thermal/int3400: export uuids
thermal: of: Extend current of-thermal.c code to allow setting emulated temp
thermal: of: Extend of-thermal to export table of trip points
thermal: of: Rename struct __thermal_trip to struct thermal_trip
thermal: of: Extend of-thermal.c to provide check if trip point is valid
thermal: of: Extend of-thermal.c to provide number of trip points
thermal: Fix error path in thermal_init()
thermal: lock the thermal zone when switching governors
thermal: core: ignore invalid trip temperature
thermal: armada: Remove support for A375-Z1 SoC
thermal: rockchip: add driver for thermal
dt-bindings: document Rockchip thermal
thermal: exynos: remove exynos_tmu_data.h include
...
There was a left over return here so the error handling isn't run.
It leads to a small memory leak and a static checker warning.
drivers/thermal/cpu_cooling.c:351 __cpufreq_cooling_register()
info: ignoring unreachable code.
Fixes: f6859014c7 ("thermal: cpu_cooling: Store frequencies in descending order")
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Avoid printing the error message in the EPROBE_DEFER case
where registering cpu cooling at ti-soc-thermal thermal driver.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Avoid printing the error message in the EPROBE_DEFER case
where registering cpu cooling at db8500 thermal driver.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
During imx_thermal probe we have the following log:
[ 1.514819] imx_thermal 2000000.aips-bus:tempmon: failed to register cpufreq cooling device: -517
[ 1.515064] platform 2000000.aips-bus:tempmon: Driver imx_thermal requests probe deferral
Avoid printing the error message in the EPROBE_DEFER case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As samsung thermal support is enabled only for ARCH_EXYNOS, there is no
need to select ARCH_HAS_BANDGAP from the arch-specific code. Removing this
dependency will also allow the driver to be enabled on 64-bit SoCs.
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Previously the return value of the last acpi_bus_get_device() was
returned. However, since we only report those issues, it should be
cleared to continue as expected.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Braswell also has package C-states which can be used for idle
injection. This patch adds Braswell CPU ID in intel powerclamp
driver.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
drivers/thermal/int340x_thermal/int3403_thermal.c:468:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Avoid pointer casting which may also lead to problems on big endian
64 bit systems.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The thermal_zone_device_unregister() function tests whether its argument
is NULL and then returns immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
INT3400 currently supports only one policy, which can't be changed.
This change exports all available policies (uuids) to user space and
allow this to be changed.
It introduces an attribute group uuids in INT3400 platform driver.
There are two attributes exposed:
- available_uuids
- current_uuid
User space can set current_uuid via this interface to one of the
available uuids. The uuid change is communicated to firmware, only
when the current zone mode is changed to "enabled". So the ideal
sequence should be
- set INT3400 zone mode to "disabled"
- change current_uuid
- set INT3400 zone mode to "enabled"
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The return code from ->get_max_state() callback was not checked during
binding cooling device to thermal zone device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Before this change it was only possible to set get_temp() and get_trend()
methods to be used in the common code handling passing parameters via
device tree to "cpu-thermal" CPU thermal zone device.
Now it is possible to also set emulated value of temperature for debug
purposes.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch extends the of-thermal.c to export trip points for a given
thermal zone.
Thermal drivers should use of_thermal_get_trip_points() method to get
pointer to table of thermal trip points.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch changes name of struct __thermal_trip to thermal_trip and moves
declaration of the latter to ./include/linux/thermal.h for better visibility.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch extends the of-thermal.c to provide check if trip point is
valid.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch extends the of-thermal.c to provide information about number of
available trip points.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Adding my copyright information for two purposes:
- To get cc'd for future patches to review (Only if people read this header
while sending mail)
- Have done enough changes to earn a place here?
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
get_property() was an over complicated beast with BUGs. It used to believe that
cpufreq table is present in ascending or descending order, which might not
always be true.
Previous patch has created another freq table in descending order for us and we
better use it now. With that get_property() simply goes away and another helper
get_level() comes in.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
CPUFreq framework *doesn't* guarantee that frequencies present in cpufreq table
will be in ascending or descending order. But cpu_cooling somehow assumes that.
Probably because most of current users are creating this list from DT, which is
done with the help of OPP layer. And OPP layer creates the list in ascending
order of frequencies.
But cpu_cooling can be used for other platforms too, which don't have
frequencies arranged in any order.
This patch tries to fix this issue by creating another list of valid frequencies
in descending order. Care is also taken to throw warnings for duplicate entries.
Later patches would use it to simplify code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We already know the value of 'cpufreq_dev->max_level' and so there is no need
calculating that once again. For this, we need to send 'cpufreq_dev' to
get_property().
Make all necessary changes for this change. Because cpufreq_cooling_get_level()
doesn't have access to 'cpufreq_dev', it is updated to iterate over the list of
cpufreq_cooling_devices to get cooling device for the cpu number passed to it.
This also makes it robust to return levels only for the CPU registered via a
cooling device. We don't have to support anything that isn't registered yet.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As we already have a list of cpufreq_cooling_devices now, lets use it instead of
a local counter.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We don't use get_property() to find max levels anymore as it is done at boot
now. So, don't support GET_MAXL in get_property().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
CPU frequency tables don't update after the driver is registered and so we don't
need to iterate over them to find total number of states every time
cpufreq_get_max_state() is called. Do it once at boot time.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
get_cpu_frequency() isn't doing much by itself, just calling get_property(). And
so this wrapper isn't required at all. Get rid of it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
cpufreq_apply_cooling() has a single caller, cpufreq_set_cur_state() and
cpufreq_set_cur_state() is an unnecessary wrapper over cpufreq_apply_cooling().
Get rid of it by merging both routines.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no point checking for validity of 'cpufreq_val' from
cpufreq_thermal_notifier() every time the routine is called. Its guaranteed to
be 0 on the first call but will be valid otherwise.
Lets update it once while the device registers.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This makes life easy and bug free. And is scalable for future resource
allocations.
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Because get_cpu_frequency() has returned a valid frequency, it means that the
cpufreq policy is surely valid and so no point checking that again with
is_cpufreq_valid(). Get rid of the routine as well as there are no more users.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
All CPUs present in 'allowed_cpus' share the same 'struct cpufreq_policy'
structure and so calling cpufreq_update_policy() for each of them doesn't make
sense.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In __cpufreq_cooling_register() we try to match min/max frequencies for all CPUs
passed in 'clip_cpus' mask. This mask is the cpumask of cpus where the frequency
constraints will be applied.
Same frequency constraint can be applied only to the CPUs belonging to the same
cluster (i.e. CPUs sharing clock line). For all such CPUs we have a single
'struct cpufreq_policy' structure managing them and so getting policies for all
CPUs wouldn't make any sense as they will all return the same pointer.
So, remove this useless check of checking min/max for all CPUs. Also update doc
comment to make this more obvious that clip_cpus should be same as
policy->related_cpus.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We aren't supposed to return our own error type here. Return what we got.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
ret is initialized before it is used, so no need to set it to 0 in its declaration.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It will be overwritten soon with return value of kzalloc().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This wasn't explained well anywhere and should be clearly specified. Lets add a
top level comment for this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
cooling_cpufreq_lock isn't used to protect this structure and so the comment
over it is outdated. Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
cpufreq_cooling_register() expects mask of all the CPUs where frequency
constraint is applicable.
This platform has more than one CPU to which these constraints will apply and so
passing mask of only CPU0 wouldn't be sufficient. Also, this platform has a
single cluster of CPUs and the constraint applies to all CPUs.
If CPU0 is hoplugged out then we may face strange BUGs as cpu_cooling framework
isn't aware of any siblings sharing clock line.
Fix it by passing cpu_present_mask to cpufreq_cooling_register().
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
cpufreq_cooling_register() expects mask of all the CPUs where frequency
constraint is applicable.
This platform has more than one CPU to which these constraints will apply and so
passing mask of only CPU0 wouldn't be sufficient. Also, this platform has a
single cluster of CPUs and the constraint applies to all CPUs.
If CPU0 is hoplugged out then we may face strange BUGs as cpu_cooling framework
isn't aware of any siblings sharing clock line.
Fix it by passing cpu_present_mask to cpufreq_cooling_register().
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
cpufreq_cooling_register() expects mask of all the CPUs where frequency
constraint is applicable.
This platform has more than one CPU to which these constraints will apply and so
passing mask of only CPU0 wouldn't be sufficient. Also, this platform has a
single cluster of CPUs and the constraint applies to all CPUs.
If CPU0 is hoplugged out then we may face strange BUGs as cpu_cooling framework
isn't aware of any siblings sharing clock line.
Fix it by passing cpu_present_mask to cpufreq_cooling_register().
Cc: Hongbo Zhang <hongbo.zhang@linaro.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In this patch, the cpu_cooling code checks for the usability of cpufreq
layer before proceeding with the CPU cooling device registration. The
main reason is: CPU cooling device is not usable if cpufreq cannot
switch frequencies.
Similar checks are spread in thermal drivers. Thus, the advantage now
is to have the check in a single place: cpu cooling device registration.
For this reason, this patch also updates the existing drivers that
depend on CPU cooling to simply propagate the error code of the cpu
cooling registration call. Therefore, in case cpufreq is not ready, the
thermal drivers will still return -EPROBE_DEFER, in an attempt to try
again when cpufreq layer gets ready.
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
thermal_unregister_governors() and class_unregister() were being called in
the wrong order.
Fixes: 80a26a5c22 ("Thermal: build thermal governors into thermal_sys module")
Cc: stable@vger.kernel.org
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Currently, userspace can request a governor change while the governor
itself is running. Grab the thermal zone lock when changing the
governor to prevent this race.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Ignore invalid trip temperature less or equal to zero. Some
buggy systems have invalid trips, causing system shutdown.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The Armada 375 Z1 SoC revision is no longer supported. This commit
removes the quirk needed for the thermal sensor.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal is TS-ADC Controller module supports
user-defined mode and automatic mode.
User-defined mode refers,TSADC all the control signals entirely by
software writing to register for direct control.
Automaic mode refers to the module automatically poll TSADC output,
and the results were checked.If you find that the temperature High
in a period of time,an interrupt is generated to the processor
down-measures taken;If the temperature over a period of time High,
the resulting TSHUT gave CRU module,let it reset the entire chip,
or via GPIO give PMIC.
Signed-off-by: zhaoyifeng <zyf@rock-chips.com>
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The functions cpufreq_cooling_unregister() and thermal_zone_device_unregister()
test whether their argument is NULL and then return immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Prevents build warning:
st_thermal.c:278:12:
warning: ‘st_thermal_suspend’ defined but not used [-Wunused-function]
st_thermal.c:286:12:
warning: ‘st_thermal_resume’ defined but not used [-Wunused-function]
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Existing code updates cupfreq policy only while executing
cpufreq_apply_cooling() function (i.e. when notify_device != NOTIFY_INVALID).
It doesn't apply constraints when cpufreq policy update happens from any other
place but it should update the cpufreq policy with thermal constraints every
time when there is a cpufreq policy update, to keep state of
cpufreq_cooling_device and max_feq of cpufreq policy in sync. For instance
while resuming cpufreq updates cpufreq_policy and it restores default
policy->usr_policy values irrespective of cooling device's cpufreq_state since
notification gets missed because (notify_device == NOTIFY_INVALID).
Another problem, is that userspace is able to change max_freq irrespective of
cooling device's state, as notification gets missed.
This patch modifies code to maintain a global cpufreq_dev_list and applies
constraints of all matching cooling devices for policy's cpu when there is any
policy update(ends up applying the lowest max_freq among the matching cpu
cooling devices).
This patch also removes redundant check (max_freq > policy->user_policy.max),
as cpufreq framework takes care of user_policy constraints already where ever
required, otherwise its causing an issue while increasing max_freq in normal
scenerio as it restores max_freq with policy->user_policy.max which is old
(smaller) value.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no longer need to share defines between exynos_tmu.c
and exynos_tmu_data.c (as they are now only used by the former
file) so move them accordingly. Then move externs for struct
exynos_tmu_init_data instances to exynos_tmu.h and remove no
longer needed exynos_tmu_data.h include.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
__EXYNOS5420_TMU_DATA macro is now identical to __EXYNOS5260_TMU_DATA
one and can be removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Maximum theoretical size saving (i.e. with only Exynos5410
SoC support enabled in kernel config so all SoC dependend
Exynos thermal driver code was dropped) is 4096 bytes so
there is no much sense in keeping these ifdefs (especially
given that they are useless once the driver gets updated to
use device tree).
While at it remove needless 'void *' casts.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Replace pdata->test_mux check in get_con_reg() by explicitly
checking for SoC type.
Also since the used pdata->test_mux value is always identical
use it directly and remove pdata->test_mux completely.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove unused TMU_SUPPORT_MULTI_INST flag, no longer
needed TMU_SUPPORTS() macro and features field from
struct exynos_tmu_platform_data.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Replace TMU_SUPPORT_ADDRESS_MULTIPLE flag check in exynos_map_dt_data()
by an explicit check for a SoC type (only Exynos5420 with TRIMINFO
quirk and Exynos5440 have TMU_SUPPORT_ADDRESS_MULTIPLE flag set in
their struct exynos_tmu_init_data instances).
Please note that this requires moving SoC type assignment and verification
from exynos_tmu_probe() to exynos_map_dt_data() so it happens earlier
(which is a good thing in itself).
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Replace TMU_SUPPORT_EMULATION flag check in exynos_tmu_set_emulation()
by an explicit check for a SoC type (all SoC types except Exynos4210
have TMU_SUPPORT_EMULATION flag set in their struct exynos_tmu_init_data
instances).
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Replace TMU_SUPPORT_EMUL_TIME flag check in get_emul_con_reg()
by an explicit check for a SoC type (all SoC types except
Exynos4210 and Exynos5440 have TMU_SUPPORT_EMUL_TIME flag set
in their struct exynos_tmu_init_data instances).
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Replace TMU_SUPPORT_FALLING_TRIP flag check in
exynos[4210,5440]_tmu_control() by an explicit check
for a SoC type (all SoC types except Exynos4210 have
TMU_SUPPORT_FALLING_TRIP flag set in their struct
exynos_tmu_init_data instances).
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add ->tmu_clear_irqs method to struct exynos_tmu_data and use
it instead exynos_tmu_clear_irqs(). Then add ->tmu_clear_irqs
implementations for Exynos4210+ and Exynos5440. Finally
remove no longer needed reg->tmu_int[stat,clear] abstractions
and struct exynos_tmu_registers instances.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add ->tmu_set_emulation method to struct exynos_tmu_data and
use it in exynos_tmu_set_emulation(). Then add ->tmu_set_emulation
implementations for Exynos4412+ and Exynos5440. Finally remove
no longer needed reg->emul_con abstraction.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Factor out code for preparing EMUL_CON register value from
exynos_tmu_set_emulation() into get_emul_con_reg().
This is a preparation for introducing per-SoC type
tmu_set_emulation method.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add ->tmu_read method to struct exynos_tmu_data and use it
in exynos_tmu_control(). Then add ->tmu_read implementations
for Exynos4210, Exynos4412+ and Exynos5440. Finally remove
no longer needed reg->tmu_cur_temp abstractions.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add ->tmu_control method to struct exynos_tmu_data and use it
in exynos_tmu_control(). Then add ->tmu_control implementations
for Exynos4210+ and Exynos5440. Finally remove no longer needed
reg->tmu_[ctrl,inten], reg->inten_rise[0,1,2,3]_shift and
reg->inten_fall0_shift abstractions.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Factor out code for preparing TMU_CONTROL register value from
exynos_tmu_control() into get_con_reg().
This is a preparation for introducing per-SoC type tmu_control
method.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add ->tmu_initialize method to struct exynos_tmu_data and
use it in exynos_tmu_initialize(). Then add ->tmu_initialize
implementations for Exynos4210, Exynos4412+ and Exynos5440.
Finally remove no longer needed reg->threshold_th[0,1],
reg->intclr_[fall,rise]_shift and reg->intclr_[rise,fall]_mask
abstractions.
There are more improvements available in the future on top
of this patch like merging HW_TRIP level setting with setting
of other levels for Exynos4412+ or adding separate method
for clearing IRQs using INTCLEAR register (for Exynos5420,
Exynos5260 and Exynos4412+).
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Factor out code for preparing threshold register value from
exynos_tmu_initialize() into get_th_reg().
This is a preparation for introducing per-SoC type tmu_initialize
method.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Factor out code for initializing data->temp_error[1,2] values
from exynos_tmu_initialize() into sanitize_temp_error().
This is a preparation for introducing per-SoC type tmu_initialize
method.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Replace TMU_SUPPORT_TRIM_RELOAD flag check in exynos_tmu_initialize()
by an explicit check for a SoC type (only Exynos3250, Exynos4412 and
Exynos5250 have TMU_SUPPORT_READY_STATUS flag set in their struct
exynos_tmu_init_data instances). Please note that this requires
adding separate SoC type for Exynos5420 so it doesn't get mistaken
with Exynos5250.
This is a preparation for introducing per-SoC type tmu_initialize
method.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Replace TMU_SUPPORT_READY_STATUS flag check in
exynos_tmu_initialize() by an explicit check for a SoC type
(all SoC types except Exynos5440 have TMU_SUPPORT_READY_STATUS
flag set in their struct exynos_tmu_init_data instances).
This is a preparation for introducing per-SoC type tmu_initialize
method.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Replace pdata->threshold_falling check for non-zero value in
exynos_tmu_initialize() by an explicit check for a SoC type
(all SoC types except Exynos5440 have pdata->threshold_falling
assigned to non-zero value in their struct exynos_tmu_registers
instances).
This is a preparation for introducing per-SoC type tmu_initialize
method.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Simplify HW_TRIP level setting in exynos_tmu_initialize() (don't
pretend that the current code is hardware and configuration
independent and just do SoC type check explicitly). Then remove
no longer needed reg->threshold_[th2,th3_l0_shift] abstractions
(only assigned for Exynos5440 in exynos5440_tmu_registers) and
EXYNOS_MAX_TRIGGER_PER_REG define.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->tmu_pmin is set to non-zero value only for Exynos5440
so replace check for non-zero value of reg->tmu_pmin by
explicitly checking for Exynos5440 SoC type. Then remove no
longer needed reg->tmu_pmin register abstraction.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->tmu_irqstatus is set to non-zero value only for Exynos5440
so replace check for non-zero value of reg->tmu_irqstatus by
explicitly checking for Exynos5440 SoC type. Then remove no
longer needed reg->tmu_irqstatus register abstraction.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->emul_time_shift is used only in exynos_tmu_set_emulation()
and accessed only if TMU_SUPPORT_EMUL_TIME flag is set. This
flag is not set for Exynos4210 and Exynos5440 (reg->emul_time_shift
field is not even assigned in exynos[4210,5440]_tmu_registers
and is assigned to identical value for all other SoC types) so
the abstraction is not needed and can be removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->emul_temp_shift is used only in exynos_tmu_set_emulation()
and accessed only if TMU_SUPPORT_EMULATION flag is set. This
flag is not set for Exynos4210 (reg->emul_temp_shift field is
not even assigned in exynos4210_tmu_registers and is assigned
to identical value for all other SoC types) so the abstraction
is not needed and can be removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->therm_trip_en_shift is used only in exynos_tmu_initialize()
and not accessed on Exynos4210 (also reg->therm_trip_en_shift is
not even assigned in exynos4210_tmu_registers but it is assigned
to identical value for all other SoC types) so the register
abstraction is not needed and can be removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->therm_trip_mode_shift and reg->therm_trip_mode_mask are
used only in exynos_tmu_control() and accessed only if
pdata->noise_cancel_mode is non-zero. pdata->noise_cancel
field is not defined on Exynos4210 (also therm_trip_mode_shift
and therm_trip_mode_mask entries are not even assigned in
exynos4210_tmu_registers but they are assigned to identical
values for all other SoC types) so the abstractions are not
needed and can be removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->test_mux_addr_shift is used only if pdata->test_mux is
non-zero. pdata->test_mux is defined only on Exynos3250 and
Exynos4412 (other SoC types don't even have pdata->test_mux
entry assigned in their struct exynos_tmu_registers instances)
so the abstraction is not needed and can be removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->triminfo_ctrl[] is used in only exynos_tmu_initialize() and
accessed only if TMU_SUPPORT_TRIM_RELOAD flag is set. This flag
is set only on Exynos3250, Exynos4412 and Exynos5250 (other SoC
types don't even have triminfo_ctrl[] entries assigned in their
struct exynos_tmu_registers instances) so the register abstraction
is not needed and can be removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->threshold_temp is used only in exynos_tmu_initialize() and
is accessed only on Exynos4210 (other SoC types don't even have
threshold_temp entry assigned in their struct exynos_tmu_registers
instances) so the register abstraction is not needed and can be
removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->tmu_status is used only in exynos_tmu_initialize() and it
is accessed only if TMU_SUPPORT_READY_STATUS flag is set. This
flag is not set for Exynos5440 and TMU_STATUS register offset
is identical for all other SoC types so the abstraction is not
needed and can be removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
reg->triminfo_data is used only in exynos_tmu_initialize() and
the code has already different paths for Exynos5440 and other
SoC types (on which TRIMINFO_DATA register offset is identical)
so the register abstraction is not needed and can be removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Different drivers request API extensions in of-thermal. For this reason,
additional callbacks are required to fit the new drivers needs.
The current API implementation expects the registering sensor driver
to provide a get_temp and get_trend callbacks as function parameters.
As the amount of callbacks is growing, this patch changes the existing
implementation to use a .ops field to hold all the of thermal callbacks
to sensor drivers.
This patch also changes the existing of-thermal users to fit the new
API design. No functional change is introduced in this patch.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: lm-sensors@lm-sensors.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Reviewed-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This adds support for the Tegra SOCTHERM thermal sensing and management
system found in the Tegra124 system-on-chip. This initial driver supports
temperature polling for four thermal zones.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch introduces a new thermal cooling device based on common clock
framework. The original motivation to write this cooling device is to be
able to cool down thermal zones using clocks that feed co-processors, such
as GPUs, DSPs, Image Processing Co-processors, etc. But it is written
in a way that it can be used on top of any clock.
The implementation is pretty straight forward. The code creates
a thermal cooling device based on a pair of a struct device and a clock name.
The struct device is assumed to be usable by the OPP layer. The OPP layer
is used as source of the list of possible frequencies. The (cpufreq) frequency
table is then used as a map from frequencies to cooling states. Cooling
states are indexes to the frequency table.
The logic sits on top of common clock framework, specifically on clock
pre notifications. Any PRE_RATE_CHANGE is hijacked, and the transition is
only allowed when the new rate is within the thermal limit (cooling state -> freq).
When a thermal cooling device state transition is requested, the clock
is also checked to verify if the current clock rate is within the new
thermal limit.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
imx_get_temp might be called before the sensor clock is prepared
thus resulting in a timeout of the first attempt to read temp:
thermal thermal_zone0: failed to read out thermal zone 0
Happened to me on a Utilite Standard with IMX6 Dual SoC.
Reason is that in imx_thermal_probe thermal_zone_device_register
is called before the sensor clock is prepared.
thermal_zone_device_register however calls
thermal_zone_device_update which eventually calls imx_get_temp.
Fix this by preparing the clock before calling
thermal_zone_device_register.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In exynos5260_tmu_registers tmu_ctrl entry is erroneously
assigned twice. The second assignment (to EXYNOS_TMU_REG_CONTROL1
define which represents 0x24 value) overrides the first one
(to EXYNOS_TMU_REG_CONTROL define which represents 0x20 value)
which results in the wrong (according to the Exynos5260 SoC
documentation that I have) offset being used for TMU_CONTROL
register. Fix it by removing the wrong assignment and then
remove no longer used EXYNOS_TMU_REG_CONTROL1 define.
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
thermal driver should be regisetered after cpufreq driver has
been registered and probed. Doing so is to make sure that thermal
driver can get the max cpu cooling states correctly when calling
get_property.
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal hysteresis represents a temperature difference.
But the original code treats it as a temperature value,
Convert it from tenths of degree Kelvin to Milli-Celsius
by deducing 273200. This is not right.
Kelvin and Celsius have same degree size. From temperature
difference view, the conversion between tenths of degree
Kelvin unit and Milli-Celsius unit is just to multiply 100.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
result is always zero when comes here.
Signed-off-by: Yao Dongdong <yaodongdong@huawei.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
* Factor out code for clearing raised IRQs from exynos_tmu_work() to
exynos_tmu_clear_irqs().
* Add a comment about documentation bugs to exynos_tmu_clear_irqs().
[ The documentation for Exynos3250, Exynos4412, Exynos5250 and
Exynos5260 incorrectly states that INTCLEAR register has
a different placing of bits responsible for FALL IRQs than
INTSTAT register. Exynos5420 and Exynos5440 documentation is
correct (Exynos4210 doesn't support FALL IRQs at all). ]
* Use exynos_tmu_clear_irqs() in exynos_tmu_initialize() instead
of open-coded code trying to clear IRQs according to predefined
masks. After this change exynos_tmu_initialize() just clears
IRQs that are raised like it is already done in exynos_tmu_work().
As a nice side-effect the code now uses the correct offset
(16 instead of 12) for bits responsible for clearing FALL IRQs
in INTCLEAR register on Exynos3250, Exynos4412 and Exynos5250.
* Remove no longer needed intclr_rise_[mask,shift] and
intclr_fall_[mask,shift] fields from struct exynos_tmu_registers.
* Remove no longer needed defines.
This patch has been tested on Exynos4412 and Exynos5420 SoCs.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Here on function return all temporarily used device nodes shall
decrement their usage counter. The problems are found with device
nodes allocated by for_each_child_of_node(), of_parse_phandle()
and of_find_node_by_name(), fix all problems at once.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: devicetree@vger.kernel.org
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch add support for TRIM_RELOAD feature at Exynos3250. The TMu of
Exynos3250 has two TRIMINFO_CON register and must need to set RELOAD bit
before reading TRIMINFO register.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch support many TRIMINFO_CTRL registers if specific Exynos SoC
has one more TRIMINFO_CTRL registers. Also this patch uses proper 'RELOAD'
shift/mask bit operation to set RELOAD feature instead of static value.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently these SoCs claim TRIM_RELOAD support but don't have
triminfo_ctrl register address defined in their struct
exynos_tmu_registers entries. This causes incorrect write of
value "1" to data->base + 0x00 address (which happens to be
TRIMINFO register). Additionally according to the documentation
that I have neither Exynos5260 nor Exynos5420 support/require
TRIM_RELOAD feature. Thus fix the aforementioned issue by
removing TMU_SUPPORT_TRIM_RELOAD flag for both Exynos5260 and
Exynos5420.
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no need for abstracting configuration for registers that
are identical on all SoC types.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
pdata->reference_voltage and pdata->gain are always defined
to non-zero values so remove the redundant checks from
exynos_tmu_control().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Cache number of non-hardware trigger levels in a new pdata field
(non_hw_trigger_levels) and convert code in exynos_tmu_initialize()
accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
* Remove dead temp check from temp_to_code() (this function users
in exynos_tmu_initialize() always pass correct temperatures and
exynos_tmu_set_emulation() returns early for EXYNOS4210 because
TMU_SUPPORT_EMULATION flag is not set on this SoC).
* Move temp_code check from code_to_temp() to exynos_tmu_read()
(code_to_temp() only user).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove runtime checks for negative return values of temp_to_code()
from exynos_tmu_initialize().
The current level temperature data hardcoded in pdata will never
cause a negative temp_to_code() return values and checking itself
is not proper. The checks in question are done at runtime in
a production code for data that is hardcoded inside driver during
development time and later it doesn't change. Such data should
be verified during development and review time (i.e. by a script
parsing relevant data from exynos_tmu_data.c, one can also argue
that verification to be done is so simple that the review by
a maintainer should be enough).
Theres should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove runtime checks for pdata sanity from exynos_tmu_initialize().
The current values hardcoded in pdata will never trigger the checks
and checking itself is not proper. The checks in question are done
at runtime in a production code for data that is hardcoded inside
driver during development time and later it doesn't change. Such
data should be verified during development and review time (i.e. by
a script parsing relevant data from exynos_tmu_data.c, one can also
argue that verification to be done is so simple that the review by
a maintainer should be enough).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The commit 1928457 ("thermal: exynos: Add hardware mode thermal
calibration support") has added HW_MODE feature but it has never
been enabled. As such it has been a dead code for over a year
now and should be removed from the kernel.
We don't keep the unused/untested features in the kernel just
in case that some future hardware might need it. Such code has
a real maintainance cost (all other code changes have to take
the dead code into account) and usually makes future changes
more difficult, not easier (i.e. recent additions of Exynos5420
SoC and Exynos5260 SoC thermal support has not made use of any
of the driver's currently unused/untested features, moreover
the recently added code is more complex than needed because of
the existing dead code). Also all removed dead code is still
accessible in the kernel git repository and can be easily
brought back if/when needed.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove unused / write-only entries from struct exynos_tmu_registers.
Then remove unused defines while at it.
We don't keep the unused/untested features in the kernel just
in case that some future hardware might need it. Such code has
a real maintainance cost (all other code changes have to take
the dead code into account) and usually makes future changes
more difficult, not easier (i.e. recent additions of Exynos5420
SoC and Exynos5260 SoC thermal support has not made use of any
of the driver's currently unused/untested features, moreover
the recently added code is more complex than needed because of
the existing dead code). Also all removed dead code is still
accessible in the kernel git repository and can be easily
brought back if/when needed.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull thermal management updates from Zhang Rui:
"Sorry that I missed the merge window as there is a bug found in the
last minute, and I have to fix it and wait for the code to be tested
in linux-next tree for a few days. Now the buggy patch has been
dropped entirely from my next branch. Thus I hope those changes can
still be merged in 3.18-rc2 as most of them are platform thermal
driver changes.
Specifics:
- introduce ACPI INT340X thermal drivers.
Newer laptops and tablets may have thermal sensors and other
devices with thermal control capabilities that are exposed for the
OS to use via the ACPI INT340x device objects. Several drivers are
introduced to expose the temperature information and cooling
ability from these objects to user-space via the normal thermal
framework.
From: Lu Aaron, Lan Tianyu, Jacob Pan and Zhang Rui.
- introduce a new thermal governor, which just uses a hysteresis to
switch abruptly on/off a cooling device. This governor can be used
to control certain fan devices that can not be throttled but just
switched on or off. From: Peter Feuerer.
- introduce support for some new thermal interrupt functions on
i.MX6SX, in IMX thermal driver. From: Anson, Huang.
- introduce tracing support on thermal framework. From: Punit
Agrawal.
- small fixes in OF thermal and thermal step_wise governor"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
Thermal: int340x thermal: select ACPI fan driver
Thermal: int3400_thermal: use acpi_thermal_rel parsing APIs
Thermal: int340x_thermal: expose acpi thermal relationship tables
Thermal: introduce int3403 thermal driver
Thermal: introduce INT3402 thermal driver
Thermal: move the KELVIN_TO_MILLICELSIUS macro to thermal.h
ACPI / Fan: support INT3404 thermal device
ACPI / Fan: add ACPI 4.0 style fan support
ACPI / fan: convert to platform driver
ACPI / fan: use acpi_device_xxx_power instead of acpi_bus equivelant
ACPI / fan: remove no need check for device pointer
ACPI / fan: remove unused macro
Thermal: int3400 thermal: register to thermal framework
Thermal: int3400 thermal: add capability to detect supporting UUIDs
Thermal: introduce int3400 thermal driver
ACPI: add ACPI_TYPE_LOCAL_REFERENCE support to acpi_extract_package()
ACPI: make acpi_create_platform_device() an external API
thermal: step_wise: fix: Prevent from binary overflow when trend is dropping
ACPI: introduce ACPI int340x thermal scan handler
thermal: Added Bang-bang thermal governor
...
we share the same driver for both ACPI predefined Fan device
and INT3404 Fan device, thus we should select the ACPI Fan
driver when int340x thermal drivers are enabeld.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp. The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI _TRT and _ART parsing code has been moved to acpi_thermal_rel such
that it can be used by other devices in the future. Use the parsing APIs
in acpi_thermal_rel.c instead.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
ACPI 4.0 introduced two thermal relationship tables via _ART
(active cooling) and _TRT (passive cooling) objects. These
tables contain many to many relationships among thermal sensors
and cooling devices.
This patch parses _ART and _TRT and makes the result available to
the userspace via an misc device interface. At the same time,
kernel drivers can also request parsing results from internal
kernel APIs.
The results include source and target devices, influence, and
sampling rate in case of _TRT. For _ART, the result shows source
device, target device, and weight percentage.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
ACPI INT3403 device object can be used to retrieve temperature date
from temperature sensors present in the system, and to expose
device' performance control.
The previous INT3403 thermal driver supports temperature reporting only,
thus remove it and introduce this new & enhanced one.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
ACPI INT3402 device object could report temperature for the memory module.
To expose such information to user space, a thermal zone device is registered
for it so that the thermal sysfs interface can expose such information for
userspace to use.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Introduce int3400 thermal driver. And make INT3400 driver
enumerate the other int340x thermal components shown in _ART/_TRT.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
It turns out that some boards can have instance->lower greater than 0 and
when thermal trend is dropping it results with next_target equal to -1.
Since the next_target is defined as unsigned long it is interpreted as
0xFFFFFFFF and larger than instance->upper.
As a result the next_target is set to instance->upper which ramps up to
maximal cooling device target when the temperature is steadily decreasing.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Newer laptops and tablets that use ACPI may have thermal sensors and
other devices with thermal control capabilities outside the core CPU/SOC,
for thermal safety reasons.
They are exposed for the OS to use via
1) INT3400 ACPI device object as the master.
2) INT3401 ~ INT340B ACPI device objects as the slaves.
This patch introduces a scan handler to enumerate the INT3400
ACPI device object to platform bus, and prevent its slaves
from being enumerated before the controller driver being probed.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Depend on MACH_KIRKWOOD, which will be set when kirkwood is built as
part of ARCH_MVEBU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Link: https://lkml.kernel.org/r/1409417172-6846-4-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The bang-bang thermal governor uses a hysteresis to switch abruptly on
or off a cooling device. It is intended to control fans, which can
not be throttled but just switched on or off.
Bang-bang cannot be set as default governor as it is intended for
special devices only. For those special devices the driver needs to
explicitely request it.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Andreas Mohr <andi@lisas.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Javi Merino <javi.merino@arm.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Peter Feuerer <peter@piie.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
i.MX6SX has some new features of thermal interrupt function,
there are LOW, HIGH and PANIC irq for thermal sensor, so add
platform data to separate different thermal version;
The reset value of LOW ALARM is 0 which means the highest
temp, so the LOW ALARM will be triggered once irq is enabled,
so we need to correct it before enabling thermal irq;
Enable PANIC ALARM as critical trip point, it will trigger
system reset via SRC module once PANIC IRQ is triggered, it
is pure hardware function, so use it instead of software
reset by cooling device.
Signed-off-by: Anson Huang <b20788@freescale.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support to check status of the thermal zone before registering the
zone. This will help on disabling some non-existing thermal zone from
the top level DTS file out of common dtsi thermalzone file.
For example,
we have 3 platforms almost same but thermal zones on this platform are
little bit different. Platform 1 and 2 have three thermal zones and
platform 3 has two thermal zones. To avoid duplication of the thermal
zones entries on each DTS file of platforms,we created one common
dtsi file for thermal zone and included this dtsi file from these
3 platform's top level dts file.
On common thermal zone com dtsi file, all thermal zone are enabled and
need to disable one of thermal zone on platform 3 dts file. For this, we
just added entry status = "disabled" for that thermal zone on platform 3
dts file and along with this change to make it work.
This way, we reuse the common file and control the enable/disable of the
thermal zone from top level dts file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Create a new event to trace when the temperature is above a trip
point. Use the trace-point when handling non-critical and critical
trip pionts.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Introduce and use an event to trace when a cooling device's state is
updated. This is useful to follow the effect of governor decisions on
cooling devices.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Create a new event to trace the temperature of a thermal zone. Using
this event trace the temperature changes of the thermal zone every-time
it is updated.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch add registers, bit fields and compatible strings for Exynos3250 TMU
(Thermal Management Unit). Exynos3250 uses the Cortex-A7 dual cores and has
a target speed of 1.0 GHz.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[Add MUX address setting bits by Jonghwa Lee]
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap<amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
It might not be a problem currently but unregister/uninitialize things
in the reverse order that they are registered/initialized.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
DT-enabled Dove has moved from ARCH_DOVE in mach-dove to MACH_DOVE
in mach-mvebu. As non-DT ARCH_DOVE will stay to rot for a while, add a new
DT-only MACH_DOVE to thermal Kconfig.
This was originally supposed to go in via "ARM: dove: prepare new Dove DT Kconfig"
patch from Sebastian Hesselbarth for 3.15, but slipped through the cracks.
I've tested on CuBox that without this patch you can't compile
dove_thermal into a mach-mvebu based kernel, and with this patch I can
build the driver and it works as expected run-time.
v2: non-ascii char creeped in somehow
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This is the traditional way of obtaining a device driver's register
address space. The aim of this driver is to supply controller specific
information to the ST Thermal Core.
Signed-off-by: Ajit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Supply controller specific information to the ST Thermal Core.
Signed-off-by: Ajit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This core is shared by both ST's 'memory mapped' and
'system configuration register' based Thermal controllers.
Signed-off-by: Ajit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
On latest i.MX6 SOC with thermal calibration data of 0x5A100000,
the critical trip temperature will be an invalid value and
cause system auto shutdown as below log:
thermal thermal_zone0: critical temperature reached(42 C),shutting down
So, with universal formula for thermal sensor, only room
temperature point is calibrated, which means the calibration
data read from fuse only has valid data of bit [31:20], others
are all 0, the critical trip point temperature can NOT depend
on the hot point calibration data, here we set it to 20 C higher
than default passive temperature.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When binding cooling devices to thermal zones created from the device
tree the minimum and maximum cooling states are in the wrong order
leading to failure to bind.
Fix the order of cooling states in the call to
thermal_zone_bind_cooling_device to fix this.
Cc:Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
It looks like this code is missing braces, otherwise the if
statement shouldn't have been indented. Fix it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
On 05/21/2014 04:22 PM, Aaron Lu wrote:
> On 05/21/2014 01:57 PM, Kui Zhang wrote:
>> Hello,
>>
>> I get following error when rmmod thermal.
>>
>> rmmod thermal
>> Killed
While dealing with this problem, I found another problem that also
results in a kernel crash on thermal module removal:
From: Aaron Lu <aaron.lu@intel.com>
Date: Wed, 21 May 2014 16:05:38 +0800
Subject: [PATCH] thermal: hwmon: Make the check for critical temp valid consistent
We used the tz->ops->get_crit_temp && !tz->ops->get_crit_temp(tz, temp)
to decide if we need to create the temp_crit attribute file but we just
check if tz->ops->get_crit_temp exists to decide if we need to remove
that attribute file. Some ACPI thermal zone doesn't have a valid critical
trip point and that would result in removing a non-existent device file
on thermal module unload.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The ACPI object definition can contain passive and critical
trip temperature. Export them via thermal sysfs.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull thermal management update from Zhang Rui:
"Specifics:
- fix a bug in Exynos thermal driver, which overwrites the hardware
trip point threshold when updating software trigger levels and
results in emergency shutdown. From: Tushar Behera.
- add thermal sensor support for Armada 375 and 38x SoCs. From
Ezequiel Garcia.
- add TMU (Thermal Management Unit) support for Exynos5260 and
Exynos5420 SoCs. From Naveen Krishna Chatradhi.
- add support for the additional digital temperature sensors in the
Intel SoCs like Bay Trail. From: Srinivas Pandruvada.
- a couple of cleanups and small fixes from Jingoo Han, Bartlomiej
Zolnierkiewicz, Geert Uytterhoeven, Jacob Pan, Paul Walmsley and
Lan,Tianyu"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (21 commits)
thermal: spear: remove unnecessary OOM messages
thermal: exynos: remove unnecessary OOM messages
thermal: rcar: remove unnecessary OOM messages
thermal: armada: Support Armada 380 SoC
thermal: armada: Support Armada 375 SoC
thermal: armada: Allow to specify an 'inverted readout' sensor
thermal: armada: Pass the platform_device to init_sensor()
thermal: armada: Add generic infrastructure to handle the sensor
thermal: armada: Add infrastructure to support generic formulas
thermal: armada: Rename armada_thermal_ops struct
thermal/intel_powerclamp: add newer cpu ids
thermal: rcar: Use pm_runtime_put() i.s.o. pm_runtime_put_sync()
thermal: samsung: Only update available threshold limits
Thermal/int3403: Fix thermal hysteresis unit conversion
thermal: Intel SoC DTS thermal
thermal: samsung: Add TMU support for Exynos5260 SoCs
thermal: samsung: Add TMU support for Exynos5420 SoCs
thermal: samsung: change base_common to more meaningful base_second
thermal: samsung: replace inten_ bit fields with intclr_
thermal: offer Samsung thermal support only when ARCH_EXYNOS is defined
...
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Now that a generic infrastructure is in place, it's possible to support
the Armada 380 SoC thermal sensor. This sensor is similar to the one
available in the already supported SoCs, with its specific temperature formula
and specific sensor initialization.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Now that a generic infrastructure is in place, it's possible to support
the new Armada 375 SoC thermal sensor. This sensor is similar to the one
available in the already supported SoCs, with its specific temperature formula
and specific sensor initialization.
In addition, we also add support for the Z1 SoC stepping, which needs
an initialization-quirk to work properly.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In order to support inverted-formula thermal sensor readout, this commit
introduces an 'inverted' field in the SoC-specific structure which
allows to specify an inversion of the temperature formula.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In order to perform SoC-specific quirks on platforms that need them,
this commit adds a new parameter to the init_sensor() function.
This will be used to support early silicons of the Armada 375 SoC,
to workaround some hardware issues.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In order to support similar SoC where the sensor value and valid
bit can have different shifts and/or mask, we add such fields to the
per-variant structure, instead of having the values hardcoded.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In order to support other similar SoC, with different sensor
coefficients, this commit adds the coeficients to the per-variant
structure, instead of having the formula hardcoded.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
As preparation work to add a generic infrastructure to support
different SoC variants, the armada_thermal_ops will be used
to host the SoC-specific fields, such as formula values and
register shifts.
For this reason, the name armada_thermal_ops is no longer suitable,
and this commit replaces it with armada_thermal_data.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Currently the threshold limits are updated in 2 stages, once for all
software trigger levels and again for hardware trip point.
While updating the software trigger levels, it overwrites the threshold
limit for hardware trip point thereby forcing the Exynos core to issue
an emergency shutdown.
Updating only the required fields in threshold register fixes this issue.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Thermal hysteresis represents a temperature difference.
But the original code treats it as a temperature value,
Convert it from tenths of degree Kelvin to Milli-Celsius
by deducing 273200. This is not right.
Kelvin and Celsius have same degree size. From temperature
difference view, the conversion between tenths of degree
Kelvin unit and Milli-Celsius unit is just to multiply 100.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In the Intel SoCs like Bay Trail, there are 2 additional digital temperature
sensors(DTS), in addition to the standard DTSs in the core. Also they support
4 programmable thresholds, out of which two can be used by OSPM. These
thresholds can be used by OSPM thermal control. Out of these two thresholds,
one is used by driver and one user mode can change via thermal sysfs to get
notifications on threshold violations.
The driver defines one critical trip points, which is set to TJ MAX - offset.
The offset can be changed via module parameter (default 5C). Also it uses
one of the thresholds to get notification for this temperature violation.
This is very important for orderly shutdown as the many of these devices don't
have ACPI thermal zone, and expects that there is some other thermal control
mechanism present in OSPM. When a Linux distro is used without additional
specialized thermal control program, BIOS can do force shutdown when thermals
are not under control. When temperature reaches critical, the Linux thermal
core will initiate an orderly shutdown.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds the registers, bit fields and compatible strings
required to support for the 5 TMU channels on Exynos5260.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Exynos5420 has 5 TMU channels, the TRIMINFO register is
misplaced for TMU channels 2, 3 and 4
TRIMINFO at 0x1006c000 contains data for TMU channel 3
TRIMINFO at 0x100a0000 contains data for TMU channel 4
TRIMINFO at 0x10068000 contains data for TMU channel 2
This patch
1 Adds the neccessary register changes and arch information
to support Exynos5420 SoCs.
2. Handles the gate clock for misplaced TRIMINFO register
3. Updates the Documentation at
Documentation/devicetree/bindings/thermal/exynos-thermal.txt
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
On Exynos5440 and Exynos5420 there are registers common
across the TMU channels.
To support that, we introduced a ADDRESS_MULTIPLE flag in the
driver and the 2nd set of register base and size are provided
in the "reg" property of the node.
As per Amit's suggestion, this patch changes the base_common
to base_second and SHARED_MEMORY to ADDRESS_MULTIPLE.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch replaces the inten_rise_shift/mask and inten_fall_shift/mask
with intclr_rise_shift/mask and intclr_fall_shift/mask respectively.
Currently, inten_rise_shift/mask and inten_fall_shift/mask bits are only used
to configure intclr related registers.
Description of H/W:
The offset for the bits in the CLEAR register are not consistent across TMU
modules in Exynso5250, 5420 and 5440.
On Exynos5250, the FALL interrupt related en, status and clear bits are
available at an offset of
16 in INTEN, INTSTAT registers and at an offset of
12 in INTCLEAR register.
On Exynos5420, the FALL interrupt related en, status and clear bits are
available at an offset of
16 in INTEN, INTSTAT and INTCLEAR registers.
On Exynos5440,
the FALL_IRQEN bits are at an offset of 4
and the RISE_IRQEN bits are at an offset of 0
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Menu for Samsung thermal support is visible on all Samsung
platforms while thermal drivers are currently available only
for EXYNOS SoCs. Fix it by replacing PLAT_SAMSUNG dependency
with ARCH_EXYNOS one.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Treat both negative and zero return values from clk_round_rate() as
errors. This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather than a
signed type, since some clock sources can generate rates higher than
(2^31)-1 Hz.
Eventually, when calling clk_round_rate(), only a return value of zero
will be considered a error. All other values will be considered valid
rates. The comparison against values less than 0 is kept to preserve
the correct behavior in the meantime.
This patch also gets rid of a comparison between unsigned and signed
values; a side-benefit.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The cpufreq core now supports the cpufreq_for_each_valid_entry macro
helper for iteration over the cpufreq_frequency_table, so use it.
Also remove the redundant !! operator.
It should have no functional changes.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull thermal management updates from Zhang Rui:
"We only have a couple of fixes/cleanups for platform thermal drivers
this time.
Specifics:
- rcar thermal driver: avoid updating the thermal zone in case an IRQ
was triggered but the temperature didn't effectively change. From
Patrick Titiano.
- update the imx thermal driver' formula of converting thermal
sensor' raw date to real temperature in degree C. From Anson
Huang.
- trivial code cleanups of ti soc thermal and rcar thermal driver
from Jingoo Han and Patrick Titiano"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: rcar-thermal: update thermal zone only when temperature changes
thermal: rcar-thermal: fix same mask applied twice
thermal: ti-soc-thermal: Use SIMPLE_DEV_PM_OPS macro
thermal: imx: update formula for thermal sensor
Avoid updating the thermal zone in case an IRQ was triggered but the
temperature didn't effectively change.
Note this is not a driver issue.
Below is a captured debug trace illustrating the purpose of this patch:
out of 8 thermal zone updates, only 2 are actually necessary.
[ 41.120000] rcar_thermal_work(): cctemp=25000
[ 41.120000] rcar_thermal_work(): nctemp=30000
[ 41.120000] rcar_thermal_work(): temp is now 30000C, update thermal zone
[ 58.990000] rcar_thermal_work(): cctemp=30000
[ 58.990000] rcar_thermal_work(): nctemp=30000
[ 58.990000] rcar_thermal_work(): same temp, do not update thermal zone
[ 59.290000] rcar_thermal_work(): cctemp=30000
[ 59.290000] rcar_thermal_work(): nctemp=30000
[ 59.290000] rcar_thermal_work(): same temp, do not update thermal zone
[ 59.590000] rcar_thermal_work(): cctemp=30000
[ 59.590000] rcar_thermal_work(): nctemp=30000
[ 59.590000] rcar_thermal_work(): same temp, do not update thermal zone
[ 59.890000] rcar_thermal_work(): cctemp=30000
[ 59.890000] rcar_thermal_work(): nctemp=30000
[ 59.890000] rcar_thermal_work(): same temp, do not update thermal zone
[ 60.190000] rcar_thermal_work(): cctemp=30000
[ 60.190000] rcar_thermal_work(): nctemp=30000
[ 60.190000] rcar_thermal_work(): same temp, do not update thermal zone
[ 60.490000] rcar_thermal_work(): cctemp=30000
[ 60.490000] rcar_thermal_work(): nctemp=30000
[ 60.490000] rcar_thermal_work(): same temp, do not update thermal zone
[ 60.790000] rcar_thermal_work(): cctemp=30000
[ 60.790000] rcar_thermal_work(): nctemp=35000
[ 60.790000] rcar_thermal_work(): temp is now 35000C, update thermal zone
I suspect this may be due to sensor sampling accuracy / fluctuation,
but no formal proof.
Signed-off-by: Patrick Titiano <ptitiano@baylibre.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Mask is already applied preceding the if statement.
Remove the second mask.
Signed-off-by: Patrick Titiano <ptitiano@baylibre.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Thermal sensor used to need two calibration points which are
in fuse map to get a slope for converting thermal sensor's raw
data to real temperature in degree C. Due to the chip calibration
limitation, hardware team provides an universal formula to get
real temperature from internal thermal sensor raw data:
Slope = 0.4297157 - (0.0015976 * 25C fuse);
Update the formula, as there will be no hot point calibration
data in fuse map from now on.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The purpose of this single series of commits from Srivatsa S Bhat (with
a small piece from Gautham R Shenoy) touching multiple subsystems that use
CPU hotplug notifiers is to provide a way to register them that will not
lead to deadlocks with CPU online/offline operations as described in the
changelog of commit 93ae4f978c (CPU hotplug: Provide lockless versions
of callback registration functions).
The first three commits in the series introduce the API and document it
and the rest simply goes through the users of CPU hotplug notifiers and
converts them to using the new method.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SW7Q
-----END PGP SIGNATURE-----
Merge tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978c ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the thermal x86-pkg-temp code by using this latter form of callback
registration.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch does a cleanup about the thermal zone govenor,
setting and make the following rule.
1. For thermal zone devices that are registered w/o tz->tzp,
they can use the default thermal governor only.
2. For thermal zone devices w/ governor name specified in
tz->tzp->governor_name, we will use the default govenor
if the governor specified is not available at the moment,
and update tz->governor when the matched governor is registered.
This also fixes a problem that OF registered thermal zones
are running with no governor.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Javi Merino <javi.merino@arm.com>
In initialization, if the cooling device is initialized at
max cooling state, and the thermal zone temperature is below
the first trip point, then the cooling state can't be updated
to the right state, untill the first trip point be triggered.
To fix this issue, allow first update of cooling device state
during registration, initialized "updated" device field as
"false" (instead of "true").
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Commit beeb5a1e (thermal: rcar-thermal: Enable driver compilation with COMPILE_TEST)
broke build on archs wihout io memory.
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/thermal/rcar_thermal.c:404: undefined reference to `devm_ioremap_resource'
drivers/thermal/rcar_thermal.c:426: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The thermal zone type should not include an instance number. Otherwise
each zone is considered a different type and the thermal-to-hwmon
bridge fails to group them all in a single hwmon device.
I also changed the type to "x86_pkg_temp", because "pkg" was too
generic, and other thermal drivers use an underscore, not a dash, as
a separator. Or maybe "cpu_pkg_temp" would be better?
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The temperature value reported by x86_pkg_temp_thermal is already
reported by the coretemp driver. So, do not expose this thermal zone
as a hwmon device, because it would be redundant.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
With the move of kirkwood into mach-mvebu, drivers Kconfig need
tweeking to allow the kirkwood specific drivers to be built.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull thermal management updates from Zhang Rui:
"This time, the biggest change is the work of representing hardware
thermal properties in device tree infrastructure.
This work includes the introduction of a device tree bindings for
describing the hardware thermal behavior and limits, and also a parser
to read and interpret the data, and build thermal zones and thermal
binding parameters. It also contains three examples on how to use the
new representation on sensor devices, using three different drivers to
accomplish it. One driver is in thermal subsystem, the TI SoC
thermal, and the other two drivers are in hwmon subsystem.
Actually, this would be the first step of the complete work because we
still need to check other potential drivers to be converted and then
validate the proposed API. But the reason why I include it in this
pull request is that, first, this change does not hurt any others
without using this approach, second, the principle and concept of this
change would not break after converting the remaining drivers. BTW,
as you can see, there are several points in this change that do not
belong to thermal subsystem. Because it has been suggested by Guenter
R that in such cases, it is recommended to send the complete series
via one single subsystem.
Specifics:
- representing hardware thermal properties in device tree
infrastructure
- fix a regression that the imx thermal driver breaks system suspend.
- introduce ACPI INT3403 thermal driver to retrieve temperature data
from the INT3403 ACPI device object present on some systems.
- introduce debug statement for thermal core and step_wise governor.
- assorted fixes and cleanups for thermal core, cpu cooling, exynos
thrmal, intel powerclamp and imx thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: remove const flag from .ops of imx thermal
Thermal: update thermal zone device after setting emul_temp
intel_powerclamp: Fix cstate counter detection.
thermal: imx: add necessary clk operation
Thermal cpu cooling: return error if no valid cpu frequency entry
thermal: fix cpu_cooling max_level behavior
thermal: rcar-thermal: Enable driver compilation with COMPILE_TEST
thermal: debug: add debug statement for core and step_wise
thermal: imx_thermal: add module device table
drivers: thermal: Mark function as static in x86_pkg_temp_thermal.c
thermal:samsung: fix compilation warning
thermal: imx: correct suspend/resume flow
thermal: exynos: fix error return code
Thermal: ACPI INT3403 thermal driver
MAINTAINERS: add thermal bindings entry in thermal domain
arm: dts: make OMAP4460 bandgap node to belong to OCP
arm: dts: make OMAP443x bandgap node to belong to OCP
arm: dts: add cooling properties on omap5 cpu node
arm: dts: add omap5 thermal data
arm: dts: add omap5 CORE thermal data
...
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
This patch provides auto disable/enable operation for boost. It uses already
present thermal infrastructure to provide BOOST hysteresis.
The TMU data is modified to work properly with or without BOOST.
Hence, the two first trip points with corresponding clip frequencies are
adjusted.
The first one is reduced from 85 to 70 degrees and the clip frequency is
increased to 1.4 GHz from 800 MHz. This trip point is in fact responsible
for providing BOOST hysteresis. When temperature exceeds 70 deg, the maximal
non BOOST frequency for Exynos4412 is imposed.
Since the first trigger level has been "stolen" for BOOST, the second one
needs to be a compromise for the previously used two for non BOOST
configuration. The 95 deg with modified clip freq (to 400 MHz) should provide
a good balance between cooling down the overheated device and throughput on
an acceptable level.
Two last trigger levels are not modified since, they cause platform shutdown
on emergency overheat to happen.
The third trip point passage results in SW managed shut down of the system.
If the last trip point is crossed, the PMU HW generates the power off
signal.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The only valid use of preempt_enable_no_resched() is if the very next
line is schedule() or if we know preemption cannot actually be enabled
by that statement due to known more preempt_count 'refs'.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: rjw@rjwysocki.net
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: rui.zhang@intel.com
Cc: jacob.jun.pan@linux.intel.com
Cc: Mike Galbraith <bitbucket@online.de>
Cc: hpa@zytor.com
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: lenb@kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-zcfvacdlvlr63qmnn5i58vuj@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As per previous changes on thermal framework API,
registering a new thermal zone does not require
a const thermal zone ops.
Thus, this patch removes the flag from imx thermal zone ops.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch is to update thermal zone device after setting emul_temp
in order to make governor work according to input temperature immediately.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Having all zero cstate count doesn't necesserily mean the cstate
counter is no functional.
Signed-off-by: Yuxuan Shui <yshuiv7@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Thermal sensor needs pll3_usb_otg when measuring temperature,
otherwise the temperature read will be incorrect, so need to
enable this clk before sensor working, for alarm function,
as hardware will take measurement periodically, so we should
keep this clk always on once alarm function is enabled.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
As per Documentation/thermal/sysfs-api.txt, max_level
is an index, not a counter. Thus, in case a CPU has
3 valid frequencies, max_level is expected to be 2, for instance.
The current code makes max_level == number of valid frequencies,
which is bogus. This patch fix the cpu_cooling device by
ranging max_level properly.
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add the module device table declaration so the module can be loaded
automatically at boot time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Mark function sys_set_trip_temp() as static in x86_pkg_temp_thermal.c
because it is not used outside this file.
This eliminates the following warning in x86_pkg_temp_thermal.c:
drivers/thermal/x86_pkg_temp_thermal.c:218:5: warning: no previous prototype for ‘sys_set_trip_temp’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch fixes a compilation warning.
warning: passing argument 5 of 'thermal_zone_device_register' discards 'const'
qualifier from pointer target type [enabled by default]
include/linux/thermal.h:270:29: note: expected 'struct thermal_zone_device_ops *'
but argument is of type 'const struct thermal_zone_device_ops *'
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Fixes regression introduced by:
commit 37713a1e8e
Author: Philipp Zabel <p.zabel@pengutronix.de>
Date: Thu Aug 1 18:33:12 2013 +0200
thermal: imx: implement thermal alarm interrupt handling
The commit 37713a1e8e makes imx thermal sensor always powered up as alarm
function is enabled, but the suspend callback of imx thermal returns
success only if thermal sensor is powered down, so it will always returns
fail hence break system's suspend, this patch disables imx thermal sensor
before suspend and re-enable it after resume.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The ACPI INT3403 device objects present on some systems can be used to retrieve
temperature data from thermal sensors. Add a driver registering each INT3403
device object as a thermal zone device and exposing its _TMP, PATx and GTSH
method via the standard thermal control interface under /sys/class/thermal/.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
People seem to delight in writing wrong and broken mwait idle routines;
collapse the lot.
This leaves mwait_play_dead() the sole remaining user of __mwait() and
new __mwait() users are probably doing it wrong.
Also remove __sti_mwait() as its unused.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jacob Jun Pan <jacob.jun.pan@linux.intel.com>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: Len Brown <lenb@kernel.org>
Cc: Rui Zhang <rui.zhang@intel.com>
Acked-by: Rafael Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20131212141654.616820819@infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch improves the ti-soc-thermal driver by adding the
support to build the thermal zones based on DT nodes.
The driver will have two options now to build the thermal
zones. The first option is the zones originally coded
in this driver. So, the driver behavior will be same
if there is no DT node describing the zones. The second
option, when it is found a DT node with thermal data,
will used the common infrastructure to build the thermal
zone and bind its cooling devices.
In case the driver loads thermal data using the legacy
mode, this driver still adds to the system
a cpufreq cooling device. Loading the thermal data from
DT, the driver assumes someone else will add the cpufreq
cooling device, like the cpufreq driver.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch introduces an API to register cpufreq cooling device
based on device tree node.
The registration via device tree node differs from normal
registration due to the fact that it is needed to fill
the device_node structure in order to be able to match
the cooling devices with trip points.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds a new API to allow registering cooling devices
in the thermal framework derived from device tree nodes.
This API links the cooling device with the device tree node
so that binding with thermal zones is possible, given
that thermal zones are pointing to cooling device
device tree nodes.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch introduces a device tree bindings for
describing the hardware thermal behavior and limits.
Also a parser to read and interpret the data and feed
it in the thermal framework is presented.
This patch introduces a thermal data parser for device
tree. The parsed data is used to build thermal zones
and thermal binding parameters. The output data
can then be used to deploy thermal policies.
This patch adds also documentation regarding this
API and how to define tree nodes to use
this infrastructure.
Note that, in order to be able to have control
on the sensor registration on the DT thermal zone,
it was required to allow changing the thermal zone
.get_temp callback. For this reason, this patch
also removes the 'const' modifier from the .ops
field of thermal zone devices.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch changes the thermal core driver to allow
registration of thermal zones without the .get_temp callback.
The idea behind this change is to allow lazy registration
of sensor callbacks.
The thermal zone will be disabled whenever the ops
does not contain a .get_temp callback. The sysfs interface
will be returning -EINVAL on any temperature read operation.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.
This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.
At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull thermal management updates from Zhang Rui:
"This time we only have a few changes as there are no soc thermal
changes from Eduardo. The only big change is the introduction of
TMON, a tool to help visualize, tune, and test the thermal subsystem.
The rest is mostly cleanups and fixes all over.
Specifics:
- introduce TMON, a tool base on thermal sysfs I/F. It can be used
to visualize, tune and test the thermal subsystem.
- fix a zone/cooling device binding problem, when both thermal zone
bind parameters and .bind() callback are available"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
tools/thermal: Introduce tmon, a tool for thermal subsystem
thermal: Fix binding problem when there is thermal zone params
thermal: cpu_cooling: fix return value check in cpufreq_cooling_register()
Thermal: Check for validity before doing kfree
thermal/intel_powerclamp: Add newer CPU models
Thermal: Tidy up error handling in powerclamp_init
thermal: Kconfig: cosmetic fixes
ACPI/thermal : Remove zone disabled warning
typo in drivers/thermal/Kconfig: lpatform instead of platform
The thermal zone params can be used to set governor
to specific thermal governor for thermal zone device.
But if the thermal zone params has only governor name
without thermal bind params, then the thermal zone device
will not be binding to cooling device. Because tz->ops->bind
operator is not invoked in bind_tz() and bind_cdev() when
there is thermal zone params.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jinyoung Park <jinyoungp@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In case of error, the function thermal_cooling_device_register() returns
ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
* pm-cpufreq: (167 commits)
cpufreq: create per policy rwsem instead of per CPU cpu_policy_rwsem
intel_pstate: Add Baytrail support
intel_pstate: Refactor driver to support CPUs with different MSR layouts
cpufreq: Implement light weight ->target_index() routine
PM / OPP: rename header to linux/pm_opp.h
PM / OPP: rename data structures to dev_pm equivalents
PM / OPP: rename functions to dev_pm_opp*
cpufreq / governor: Remove fossil comment
cpufreq: exynos4210: Use the common clock framework to set APLL clock rate
cpufreq: exynos4x12: Use the common clock framework to set APLL clock rate
cpufreq: Detect spurious invocations of update_policy_cpu()
cpufreq: pmac64: enable cpufreq on iMac G5 (iSight) model
cpufreq: pmac64: provide cpufreq transition latency for older G5 models
cpufreq: pmac64: speed up frequency switch
cpufreq: highbank-cpufreq: Enable Midway/ECX-2000
exynos-cpufreq: fix false return check from "regulator_set_voltage"
speedstep-centrino: Remove unnecessary braces
acpi-cpufreq: Add comment under ACPI_ADR_SPACE_SYSTEM_IO case
cpufreq: arm-big-little: use clk_get instead of clk_get_sys
cpufreq: exynos: Show a list of available frequencies
...
Conflicts:
drivers/devfreq/exynos/exynos5_bus.c
Commit b82715fdd4 introduces
a 'device' subdirectory under /sys/class/hwmon/hwmonX/ directory,
for the thermal_zone hwmon devices. And this results in different
handling by libsensors.
The problem is reported and discussed in this thread
http://marc.info/?l=linux-pm&m=138229306109596&w=2
This patch reverts commit b82715fdd4.
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
CONFIG_CPU_FREQ_TABLE will be always enabled when cpufreq framework is used, as
cpufreq core depends on it. So, we don't need this CONFIG option anymore as it
is not configurable. Remove CONFIG_CPU_FREQ_TABLE and update its users.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch changes the behavior of TI SoC thermal driver
when there is a PCB thermal zone.
Instead of reporting an error code when reading from
PCB temperature sensor fails, this patch will make
the driver attempt to compose the hotspot extrapolation
based on bandgap readings only.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
The commit d0a0ce3e77 ("thermal: exynos: Add
missing definations and code cleanup") has removed setting of test MUX address
value at TMU configuration setting.
This field is not present on Exynos4210 and Exynos5 SoCs. However on Exynos4412
SoC it is required to set this field after reset because without it TMU shows
maximal available temperature, which causes immediate platform shutdown.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Up till now Exynos5250 and Exynos4412 had the same definitions for TMU
data. Following commit changes that, by introducing separate
exynos4412_default_tmu_data structure.
Since Exynos4412 was chronologically first, the corresponding name for
TMU registers and default data was renamed.
Additionally, new SOC_ARCH_EXYNOS4412 type has been defined.
Moreover, the SOC_ARCH_EXYNOS name has been changed to SOC_ARCH_EXYNOS5250.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
The commit 4de0bdaa96
("thermal: exynos: Add support for instance based register/unregister")
broke check for presence of therm_dev at global thermal zone in
exynos_report_trigger().
The resulting wrong test prevents thermal_zone_device_update() call, which
calls handlers for situation when trip points are passed.
Such behavior prevents thermal driver from proper reaction (when TMU interrupt
is raised) in a situation when overheating is detected at TMU hardware.
It turns out, that after exynos thermal subsystem redesign (at v3.12) this
check is not needed, since it is not possible to register thermal zone
without valid thermal device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
The thermal_release function is called whenever
any device belonging to 'thermal' class unregisters.
This function performs kfree(cdev) without any check.
In cases where there are more device registrations
other than just 'thermal_zone' and 'cooling_device'
this might accidently free memory allocated them
silently; and cause memory errors.
This patch changes this behavior by doing
kfree(cdev) only when the device pointer belongs
to a real cdev i.e. cooling_device.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This will enable intel_powerclamp driver on newer Intel CPUs
including some Ivy Bridge and Haswell processors.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch
* adds missing kfree() for cpu_clamping_mask
* adds return value checking for alloc_percpu()
* unregister hotcpu notifier in exit path
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
x86_pkg_temp receives thermal notifications via a callback from a
therm_throt driver, where thermal interrupts are processed.
This callback is pkg_temp_thermal_platform_thermal_notify. Here to
avoid multiple interrupts from cores in a package, we disable the
source and also set a variable to avoid scheduling delayed work function.
This variable is protected via spin_lock_irqsave. On one buggy platform,
we still receiving interrupts even if the source is disabled. This
can cause deadlock/lockdep warning, when interrupt is generated while under
spinlock in work function.
Change spin_lock to spin_lock_irqsave and spin_unlock to
spin_unlock_irqrestore as the data it is trying to protect can also
be modified in a notification call called from interrupt handler.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch avoids NULL pointer accesses while unregistering
cpu cooling devices, in case a NULL pointer is received.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
When registering a thermal zone device using platform information
via bind_params, the thermal framework will always perform the
cdev binding using the lowest and highest limits (THERMAL_NO_LIMIT).
This patch changes the data structures so that it is possible
to inform what are the desired limits for each trip point
inside a bind_param. The way the binding is performed is also
changed so that it uses the new data structure.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
When registering a new thermal_device, the thermal framework
will always add a hwmon sysfs interface.
This patch adds a flag to make this behavior optional. Now
when registering a new thermal device, the caller can
optionally inform if hwmon interface is desirable. This can
be done by means of passing a thermal_zone_params.no_hwmon == true.
In order to keep same behavior as of today, all current
calls will by default create the hwmon interface.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-acpi@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: Zhang Rui <rui.zhang@intel.com>
Suggested-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
When creating virtual hwmon devices based out of thermal
zone devices, the virtual devices won't have parents.
This patch changes the code so that the parent of virtual
hwmon devices is the thermal zone device that they are
based of.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
In order to improve code organization, this patch
moves the hwmon sysfs support to a file named
thermal_hwmon. This helps to add extra support
for hwmon without scrambling the code.
In order to do this move, the hwmon list head is now
using its own locking. Before, the list used
the global thermal locking. Also, some minor changes
in the code were required, as recommended by checkpatch.pl.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Commit 1cd1ecb6 ("thermal: exynos: Remove non DT based support")
cleaned up some non-DT code. However, there were few more things
needed for complete cleanup to make this driver DT only.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
NULL pointer was being dereferenced in its own error message.
Changed it to the correct device pointer.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Workaround to compute thermal trend even when update interval
is not set. This patch will ensure to compute the thermal trend
when bandgap counter delay is not set.
Signed-off-by: Ranganath Krishnan <ranganath@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Set the bandgap mask counter_delay with the polling_delay value on
registering the thermal zone. This patch will ensure to get the
correct update interval for computing the thermal trend.
Signed-off-by: Ranganath Krishnan <ranganath@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
In case the trend is not changing or when there is no
request for throttling, it is expected that the instance
would not change its requested target. This patch improves
the code implementation to cover for this expected behavior.
With current implementation, the instance will always
reset to cdev.cur_state, even in not expected cases,
like those mentioned above.
This patch changes the step_wise governor implementation
of get_target so that we accomplish:
(a) - default value will be current instance->target, so
we do not change the thermal instance target unnecessarily.
(b) - the code now it is clear about what is the intention.
There is a clear statement of what are the expected outcomes
(c) - removal of hardcoded constants, now it is put in use
the THERMAL_NO_TARGET macro.
(d) - variable names are also improved so that reader can
clearly understand the difference between instance cur target,
next target and cdev cur_state.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reported-by: Ruslan Ruslichenko <ruslan.ruslichenko@ti.com>
Signed-of-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The cooling device only needs update on a new target state. Since we
already check old target in thermal_zone_trip_update(), we can do one
more check to see if it's a new target state. If not, we can reasonably
save some uncecesary code execution.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
cpufreq_thermal_notifier() is to change the cpu's cpufreq in the allowed_cpus mask
when associated thermal-cpufreq cdev's cooling state is changed. It's a cpufreq policy
notifier handler and it will be triggered even if those cpus out of allowed_cpus has
changed freq policy.
cpufreq_thermal_notifier() checks the policy->cpu. If it belongs to allowed_cpus,
change max_freq(default to 0) to the desire cpufreq value and pass 0 and max_freq
to cpufreq_verify_within_limits() as cpufreq scope. But if not, do nothing and
max_freq will remain 0. This will cause the cpufreq scope to become 0~0. This
is not right. This patch is to return directly after finding cpu not belonging
to allowed_cpus.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The error check is checking for a "base" mapped memory base
instead of "base_common". Fixing the same.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enable automatic measurements at 10 Hz and use the alarm interrupt to react
more quickly to sudden temperature changes above the passive or critical
temperature trip points.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Set passive and critical trip point values depending on the maximum die
temperature stored in the OCOTP fuses. This allows higher trip points
for industrial and automotive rated i.MX6 SoCs.
Also allow to configure the passive trip point from userspace.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
TMU probe function now checks for a device tree defined regulator.
For compatibility reasons it is allowed to probe driver even without
this regulator defined.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds support for h/w mode calibration in the TMU controller.
Soc's like 5440 support this features. The h/w bits needed for calibration
setting are same as that of enum calibration_type.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch sets the second point trimming value according to the platform
data if the register value is 0.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds configuration data for exynos5440 soc. Also register
definations for the controller are added.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch modifies TMU controller to add changes needed to work with
exynos5440 platform. This sensor registers 3 instance of the tmu controller
with the thermal zone and hence reports 3 temperature output. This controller
supports upto five trip points. For critical threshold the driver uses the
core driver thermal framework for shutdown.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Jungseok Lee <jays.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds support to parse one more common set of TMU register. First
set of register belongs to each instance of TMU and second set belongs to
common TMU registers.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch uses the device pointer stored in the configuration structure
and converts to dev_* prints and devm API's.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds several features supported by TMU as bitfields.
This features varies across different SOC type and comparing
the features present in the TMU is more logical than comparing
the soc itself.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds support to handle multiple instances of the TMU controllers.
This is done by removing the static structure to register with the core thermal
and creating it dynamically for each instance of the TMU controller. The
interrupt is made shared type to handle shared interrupts. Now since the ISR needs
the core thermal framework to be registered so request_irq is moved after the core
registration is done.
Also the identifier of the TMU controller is extracted from device tree alias. This
will be used for TMU specific initialisation.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Recently non DT support from Exynos platform is removed and hence
removing non DT support from the driver also. This will help in easy
maintainence.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This code simplifies the zone handling to use the trip information passed
by the TMU driver and not the hardcoded macros. This also helps in adding
more zone support.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch removes the error return in the bind/unbind routine
as the platform may not register any cpufreq cooling data.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch renames member private_data to driver_data of the thermal
zone registration structure as this item stores the driver related
data and uses it to call the driver related callbacks.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This code modifies the thermal driver to have multiple thermal zone
support by replacing the global thermal zone variable with device data
member of thermal_zone_device.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch uses the TMU status register to know the generated interrupts
and only clear them in the interrupt handler.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
TMU urgently sends active-high signal (thermal trip) to PMU, and thermal
tripping by hardware logic. Thermal tripping means that PMU cuts off the
whole power of SoC by controlling external voltage regulator.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch migrates the TMU register definition/bitfields to data file. This
is needed to support SoC's which use the same TMU controller but register
validity, offsets or bitfield may slightly vary across SOC's.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds entries min_efuse_value, max_efuse_value, default_temp_offset,
trigger_type, cal_type, trim_first_point, trim_second_point, max_trigger_level
trigger_enable in the TMU platform data structure. Also the driver is modified
to use the data passed by these new platform memebers instead of the constant
macros. All these changes helps in separating the SOC specific data part from
the TMU driver.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds some extra register bitfield definations and cleans
up the code to prepare for moving register macros and definations inside
the TMU data section. In this code cleanup the TMU enable bit is correctly used
as bit0 and bit1 is taken care which is reserve bit.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This code splits the exynos tmu driver code into SOC specific data parts.
This will simplify adding new SOC specific data to the same TMU controller.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch renames and moves include/linux/platform_data/exynos_thermal.h to
drivers/thermal/samsung/exynos_tmu.h. This file movement is needed as exynos
SOC's are not supporting non-DT based platforms and this file now just contains
exynos tmu driver related definations.
Also struct freq_clip_table is now moved to exynos_thermal_common.c as it fixes
the compilation issue occuring because now this new tmu header file is included
in tmu driver c file and not in the common thermal header file.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch renames exynos_thermal.c to exynos_tmu.c. This change is needed as
this file now just contains exynos tmu driver related codes and thermal zone
or cpufreq cooling registration related changes are not there anymore.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This code bifurcates exynos thermal implementation into common and sensor
specific parts. The common thermal code interacts with core thermal layer and
core cpufreq cooling parts and is independent of SOC specific driver. This
change is needed to cleanly add support for new TMU sensors.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch removes the dependency on CPU_THERMAL for compiling TMU driver.
This is useful for cases when only TMU controller needs to be initialised
without cpu cooling action.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch uses the recently added config sybmol ARCH_HAS_BANDGAP to enable
the TMU driver. This will allow adding support for new soc easily as now it
is the platform responsibility to enable this config symbol for a particular
soc.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This movement of files is done for easy maintenance and adding more
new sensor's support for exynos platform easily . This will also help in
bifurcating exynos common, sensor driver and sensor data related parts.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This is based on the initial imx thermal work done by
Rob Lee <rob.lee@linaro.org> (Not sure if the email address is still
valid). Since he is no longer interested in the work and I have
rewritten a significant amount of the code, I just took the authorship
over from him.
It adds the imx thermal support using Temperature Monitor (TEMPMON)
block found on some Freescale i.MX SoCs. The driver uses syscon regmap
interface to access TEMPMON control registers and calibration data, and
supports cpufreq as the cooling device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Commit f1a18a105 "Thermal: CPU Package temperature thermal" had code
that did a get_online_cpus(), run a loop and then do a
put_online_cpus(). The problem is that the loop had an error exit that
would skip the put_online_cpus() part.
In the error exit part of the function, it also did a get_online_cpus(),
run a loop and then put_online_cpus(). The only way to get to the error
exit part is with get_online_cpus() already performed. If this error
condition is hit, the system will be prevented from taking CPUs offline.
The process taking the CPU offline will lock up hard.
Removing the get_online_cpus() removes the lockup as the hotplug CPU
refcount is back to zero.
This was bisected with ktest.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Although it is unlikley that physical package id is set to some
arbitary number, it is better to prevent in anycase. Since package
temp zones use this in thermal zone type and for allocation, added
a limit.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
If krealloc() returns NULL, it doesn't free the original. So any code
of the form 'foo = krealloc(foo, ...);' is almost certainly a bug.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
On systems with no package MSR support this caused crash as there
is a bug in the logic to check presence of DTHERM and PTS feature
together. Added a change so that when there is no PTS support, module
doesn't get loaded. Even if some CPU comes online with the PTS
feature disabled, and other CPUs has this support, this patch
will still prevent such MSR accesses.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reported-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull thermal management updates from Zhang Rui:
"There are not too many changes this time, except two new platform
thermal drivers, ti-soc-thermal driver and x86_pkg_temp_thermal
driver, and a couple of small fixes.
Highlights:
- move the ti-soc-thermal driver out of the staging tree to the
thermal tree.
- introduce the x86_pkg_temp_thermal driver. This driver registers
CPU digital temperature package level sensor as a thermal zone.
- small fixes/cleanups including removing redundant use of
platform_set_drvdata() and of_match_ptr for all platform thermal
drivers"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: cpu_cooling: fix stub function
thermal: ti-soc-thermal: use standard GPIO DT bindings
thermal: MAINTAINERS: Add git tree path for SoC specific updates
thermal: fix x86_pkg_temp_thermal.c build and Kconfig
Thermal: Documentation for x86 package temperature thermal driver
Thermal: CPU Package temperature thermal
thermal: consider emul_temperature while computing trend
thermal: ti-soc-thermal: add DT example for DRA752 chip
thermal: ti-soc-thermal: add dra752 chip to device table
thermal: ti-soc-thermal: add thermal data for DRA752 chips
thermal: ti-soc-thermal: remove usage of IS_ERR_OR_NULL
thermal: ti-soc-thermal: freeze FSM while computing trend
thermal: ti-soc-thermal: remove external heat while extrapolating hotspot
thermal: ti-soc-thermal: update DT reference for OMAP5430
x86, mcheck, therm_throt: Process package thresholds
thermal: cpu_cooling: fix 'descend' check in get_property()
Thermal: spear: Remove redundant use of of_match_ptr
Thermal: kirkwood: Remove redundant use of of_match_ptr
Thermal: dove: Remove redundant use of of_match_ptr
Thermal: armada: Remove redundant use of of_match_ptr
...
This change updates the ti-soc-thermal driver to use
standard GPIO DT bindings to read the GPIO number associated
to thermal shutdown IRQ, in case the device features it.
Previously, the code was using a specific DT bindings.
As now OMAP supports the standard way to model GPIOs,
there is no point in having a ti specific binding.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
EXYNOS4212 and EXYNOS4412 have the same thermal block, so there is no
reason to include support only for EXYNOS4412 in this driver.
Cc: linux-pm@vger.kernel.org
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix build error in x86_pkg_temp_thermal.c. It requires that
X86_MCE & X86_THERMAL_VECTOR be enabled, so depend on the latter symbol,
since it depends on X86_MCE (indirectly).
Also, X86_PKG_TEMP_THERMAL is already inside an "if THERMAL" block,
so remove that duplicated dependency.
ERROR: "platform_thermal_package_rate_control" [drivers/thermal/x86_pkg_temp_thermal.ko] undefined!
ERROR: "platform_thermal_package_notify" [drivers/thermal/x86_pkg_temp_thermal.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This driver register CPU digital temperature sensor as a thermal
zone at package level.
Each package will show up as one zone with at max two trip points.
These trip points can be both read and updated. Once a non zero
value is set in the trip point, if the package package temperature
goes above or below this setting, a thermal notification is
generated.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In case emulated temperature is in use, using the trend
provided by driver layer can lead to bogus situation.
In this case, debugger user would set a temperature value,
but the trend would be from driver computation.
To avoid this situation, this patch changes the get_tz_trend()
to consider the emulated temperature whenever that is in use.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds the thermal data for TI DRA752 chips.
In this change it includes (autogen):
. Register offset definitions
. Bitfields and masks for all registers
. Conversion table
Also, the thermal limits, thresholds and extrapolation
rules are included. The extrapolation rule is simply
add +2C as margin.
All 5 sensors, MPU, GPU, CORE, DSPEVE and IVA, are defined
and exposed. Only MPU has cooling device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch changes the driver to avoid the usage of IS_ERR_OR_NULL()
macro. This macro can lead to dangerous results, like returning
success (0) during a failure scenario (NULL pointer handling).
For this reason this patch is changing the driver after
revisiting the code. These are the cases:
i. For cases in which IS_ERR_OR_NULL() is used for checking
return values of functions that returns either PTR_ERR()
or a valid pointer, it has been translated to IS_ERR() check only.
ii. For cases that a NULL check is still needed, it has been
translated to if (!ptr || IS_ERR(ptr)).
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In order to read the history buffer, it is required to
freeze BG FSM. This patch adds the missing piece of code
to freeze the FSM and also a contention area to avoid
other parts of the code to access the DTEMPs.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
For boards that provide a PCB sensor close to SoC junction
temperature, it is possible to remove the cumulative heat
reported by the SoC temperature sensor.
This patch changes the extrapolation computation to consider
an external sensor in the extrapolation equations.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The variable 'descend' is initialized as -1 in function get_property(),
and will never get any chance to be updated by the following code.
if (freq != CPUFREQ_ENTRY_INVALID && descend != -1)
descend = !!(freq > table[i].frequency);
This makes function get_property() return the wrong frequency for given
cooling level if the frequency table is sorted in ascending. Fix it
by correcting the 'descend' check in if-condition to 'descend == -1'.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
'spear_thermal_id_table' is always compiled in and the driver
is dependent on OF. Hence use of of_match_ptr is unnecessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Vincenzo Frascino <vincenzo.frascino@st.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
'kirkwood_thermal_id_table' is always compiled in and the driver
is dependent on OF. Hence use of of_match_ptr is unnecessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
'dove_thermal_id_table' is always compiled in and the driver
is dependent on OF. Hence use of of_match_ptr is unnecessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
'armada_thermal_id_table' is always compiled in and the driver
is dependent on OF. Hence use of of_match_ptr is unnecessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_ioremap_resource does sanity checks on the given resource.
No need to duplicate this in the driver.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Vincenzo Frascino <vincenzo.frascino@st.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
This patch adds a requirement needing .get_trip_temp() callback
function for registering thermal zone device. This function is
used when thermal zone is updated and essential where thermal core
handles thermal trip based only polling way not hw interrupt.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Setting policy results in invalid value error.
% echo "step_wise" > policy
% echo: write error: Invalid argument
Need clean up of the buffer which "echo" may add based on the arguments, before
comparing aganist list of governor names.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Tested-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use the newly introduced devm_ioremap_resource().
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
CC: Vincenzo Frascino <vincenzo.frascino@st.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Vincenzo Frascino <vincenzo.frascino@st.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch changes the driver to avoid the usage of IS_ERR_OR_NULL()
macro. This macro can lead to dangerous results, like returning
success (0) during a failure scenario (NULL pointer handling).
The case present in this driver can be translated to a simple
check for IS_ERR(), as the cpufreq_cooling_register() returns
either a valid pointer or an ERR_PTR().
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Hongbo Zhang <hongbo.zhang@stericsson.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch changes the driver to avoid the usage of IS_ERR_OR_NULL()
macro. This macro can lead to dangerous results, like returning
success (0) during a failure scenario (NULL pointer handling).
The case present in this patch has simply be translated to
normal check for NULL and if the pointer has an error code.
The later case is needed because functions like
thermal_zone_get_zone_by_name() could return an ERR_PTR().
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Improve code readiness by changing alignments so that
they match open parenthesis, like checkpatch.pl --strict
suggests.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There are at least three patterns for oneline comments in this
file. This patch changes them to one single pattern
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Just for code readiness, this patch makes all functions
on this file to have a blank line before their returns.
Now, some functions follow this pattern, and others will
not have a blank line. So, this patch makes it a single
pattern.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch updates the documentation for thermal_zone_device_register
and removes the warnings generated by scripts/kernel-doc -v.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch updates the documentation for create_trip_attrs
and removes the warnings generated by scripts/kernel-doc -v.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch updates the documentation for thermal_cooling_device_register
and removes the warnings generated by scripts/kernel-doc -v.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch updates the documentation for thermal_zone_unbind_cooling_device
and removes the warnings generated by scripts/kernel-doc -v.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch updates the documentation for thermal_zone_bind_cooling_device
and removes the warnings generated by scripts/kernel-doc -v.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
To follow the prefix names used by the thermal functions,
this patch renames notify_thermal_framework to thermal_notify_framework.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
As per the comment at the top of this file, this is a GPLv2 driver.
This patch updates the driver license accordingly.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The list is not needed so far. Thus removing it.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Just for style purposes, remove extra curl brackets.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Limit the amount of bytes written to dev_name by
secure writing with snprintf.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Update comments for this exported function.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add proper documentation for exported function cpufreq_cooling_register.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
