Similar to suspend, ufshcd interrupt can be disabled since there won't be
any host controller transaction expected till clocks ungated.
Link: https://lore.kernel.org/r/1575721321-8071-3-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During suspend flow, interrupt shall be disabled before disabling clocks to
avoid potential system hang due to accessing host registers after host
clocks are disabled.
For example, if an interrupt comes with IRQF_IRQPOLL flag configured with
the misrouted interrupt recovery feature enabled, ufshcd ISR may be
triggered even if nothing shall be done for UFS. In this case, system hang
may happen if UFS interrupt status register is accessed with host clocks
disabled.
Link: https://lore.kernel.org/r/1575721321-8071-2-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We know that "check_for_bkops" is non-zero on this side of the || because
it was checked on the other side.
Link: https://lore.kernel.org/r/20191213104935.wgpq2epaz6zh5zus@kili.mountain
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We introduced a few new error paths, but we can't return directly, we first
have to unlock "hba->clk_scaling_lock" first.
Fixes: a276c19e3e98 ("scsi: ufs: Avoid busy-waiting by eliminating tag conflicts")
Link: https://lore.kernel.org/r/20191213104828.7i64cpoof26rc4fw@kili.mountain
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Backup L4 attributes duirng manual hibern8 entry and restore the L4
attributes on manual hibern8 exit as per JESD220C.
Link: https://lore.kernel.org/r/1575606303-10917-1-git-send-email-sheebab@cadence.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sheeba B <sheebab@cadence.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since ufshcd irq resource is allocated with the device resource management
aware IRQ request implementation, we don't really need to free up irq
during suspend, disabling it during suspend and reenabling it during resume
should be good enough.
Link: https://lore.kernel.org/r/0101016ed3d69793-22918f99-23bf-495d-8a36-a9c108d1cbce-000000@us-west-2.amazonses.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During power mode change, PACP_PWR_Req frame sends PAPowerModeUserData
parameters (and they are considered valid by device if Flags[4] -
UserDataValid bit is set in the same frame). Currently we don't set these
PAPowerModeUserData parameters and hardware always sets UserDataValid bit
which would clear all the DL layer timeout values of the peer device after
the power mode change.
This change sets the PAPowerModeUserData[0..5] to UniPro specification
recommended default values, in addition we are also setting the relevant
DME_LOCAL_* timer attributes as required by UFS HCI specification.
Link: https://lore.kernel.org/r/0101016ed3d688a4-cfaeb1c9-238b-46c4-9c89-d48c410ba325-000000@us-west-2.amazonses.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS standard requires DBD field to be set to 1 in MODE SENSE(10).
Some card vendors are more strict and check the DBD field, hence respond
with CHECK_CONDITION (Sense key set to ILLEGAL_REQUEST and ASC set to
INVALID FIELD IN CDB). When host sends MODE SENSE for page caching, as a
result of the CHECK_CONDITION response, host assumes that the device
doesn't support the cache feature and doesn't send SYNCHRONIZE_CACHE
commands to flush the device cache. This can result in data corruption in
case of sudden power down when there is data stored in the device cache.
This patch fixes the DBD field setting as required in UFS standard.
Link: https://lore.kernel.org/r/0101016ed3d657e4-32a6dd52-1505-4312-97ff-2bd3bee59eb7-000000@us-west-2.amazonses.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In UFS host reset and restore path, before probe, we stop and start the
host controller once. After host controller is stopped, the pending
requests, if any, are cleared from the doorbell, but no completion IRQ
would be raised due to the hba is stopped. These pending requests shall be
completed along with the first NOP_OUT command (as it is the first command
which can raise a transfer completion IRQ) sent during probe. Since the
OCSs of these pending requests are not SUCCESS (because they are not yet
literally finished), their UPIUs shall be dumped. When there are multiple
pending requests, the UPIU dump can be overwhelming and may lead to
stability issues because it is in atomic context. Therefore, before probe,
complete these pending requests right after host controller is stopped and
silence the UPIU dump from them.
Link: https://lore.kernel.org/r/1574751214-8321-5-git-send-email-cang@qti.qualcomm.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To be on the safe side, do not touch lrb after clearing its slot in the
lrb_in_use bitmap to avoid messing up the next task which would possibly
occupy this lrb.
[mkp: applied by hand]
Link: https://lore.kernel.org/r/1574751214-8321-4-git-send-email-cang@qti.qualcomm.com
Reviewed by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Per UFS 3.0 JEDEC standard, the VCCQ2 min voltage is 1.7v and the VCCQ
voltage range is 1.14v ~ 1.26v. Update their hard codes accordingly to make
sure they work in a safe range compliant for ver 1.0/1.1/2.0/2.1/3.0 UFS
devices.
Link: https://lore.kernel.org/r/1574751214-8321-3-git-send-email-cang@qti.qualcomm.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bkops level should be rechecked upon receiving an exception. Currently the
level is being cached and never updated.
Update bkops each time the level is checked. Also do not use the cached
bkops level value if it is disabled and then enabled.
Fixes: afdfff59a0 (scsi: ufs: handle non spec compliant bkops behaviour by device)
Link: https://lore.kernel.org/r/1574751214-8321-2-git-send-email-cang@qti.qualcomm.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Manage TMF tags with blk_{get,put}_request() instead of
ufshcd_get_tm_free_slot() / ufshcd_put_tm_slot(). Store a per-request
completion pointer in request.end_io_data instead of using a waitqueue to
report TMF completion.
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191209181309.196233-3-bvanassche@acm.org
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of tracking which tags are in use in the ufs_hba.lrb_in_use
bitmask, rely on the block layer tag allocation mechanism. This patch
removes the following busy-waiting loop if ufshcd_issue_devman_upiu_cmd()
and the block layer accidentally allocate the same tag for a SCSI request:
* ufshcd_queuecommand() returns SCSI_MLQUEUE_HOST_BUSY.
* The SCSI core requeues the SCSI command.
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191209181309.196233-2-bvanassche@acm.org
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The FSC (NCR53CF9x-2 / SYM53CF9x-2) has a different family code than QLogic
or Emulex parts. This caused it to be detected as a FAS100A.
Unforunately, this meant the configuration of the CONFIG3 register was
incorrect. This causes data transfer issues with FAST-SCSI targets.
The FSC also has the CONFIG4 register. It can be used to enable a feature
called Active Negation which should always be enabled according to the data
manual.
Link: https://lore.kernel.org/r/20191119202021.28720-3-jongk@linux-m68k.org
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The order of the definitions in the esp_rev enum is important. The values
are used in comparisons for chip features.
Add a comment to the enum explaining this.
Also, the actual values for the enum fields are irrelevant, so remove the
explicit values (suggested by Geert Uytterhoeven). This makes adding a new
field in the middle of the enum easier.
Finally, move the PCSCSI definition to the right place in the enum. In its
previous location, at the end of the enum, the wrong values are written to
the CONFIG3 register when used with FAST-SCSI targets.
Link: https://lore.kernel.org/r/20191119202021.28720-2-jongk@linux-m68k.org
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cxgb4i_ddp_init() fails then cdev->cdev2ppm will be NULL, so add a check
for NULL pointer before dereferencing it.
Link: https://lore.kernel.org/r/1576676731-3068-1-git-send-email-varun@chelsio.com
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are spelling mistakes of asynchronous in a lpfc_printf_log message
and comments. Fix these.
Link: https://lore.kernel.org/r/20191218084301.627555-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent change appears to have moved an #endif by accident:
drivers/scsi/lpfc/lpfc_debugfs.c:5393:18: error: 'lpfc_debugfs_dumpHBASlim_open' undeclared here (not in a function); did you mean 'lpfc_debugfs_op_dumpHBASlim'?
drivers/scsi/lpfc/lpfc_debugfs.c:5394:18: error: 'lpfc_debugfs_lseek' undeclared here (not in a function); did you mean 'lpfc_debugfs_nvme_trc'?
drivers/scsi/lpfc/lpfc_debugfs.c:5395:18: error: 'lpfc_debugfs_read' undeclared here (not in a function); did you mean 'lpfc_debug_dump_q'?
drivers/scsi/lpfc/lpfc_debugfs.c:5396:18: error: 'lpfc_debugfs_release' undeclared here (not in a function); did you mean 'lpfc_debugfs_terminate'?
drivers/scsi/lpfc/lpfc_debugfs.c:5402:18: error: 'lpfc_debugfs_dumpHostSlim_open' undeclared here (not in a function); did you mean 'lpfc_debugfs_op_dumpHostSlim'?
Move it back to where it was previously.
Fixes: 95bfc6d8ad ("scsi: lpfc: Make FW logging dynamically configurable")
Link: https://lore.kernel.org/r/20191216131701.3125077-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
24 fixes, all in drivers. The lion's share (16) are qla2xxx and the
rest are iscsi (3), ufs (2), smarpqi, lpfc and libsas.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXfUGbSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishRNxAP4zxu9A
93AijCfJaMhtuzh2bdegf1IC/LXhbu69CQm9bgD+OeQLR9XvopjRBsQC35W1Im5T
73K+w8YTyddZEkOvcio=
=m0Xq
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"24 fixes, all in drivers. The lion's share (16) are qla2xxx and the
rest are iscsi (3), ufs (2), smarpqi, lpfc and libsas"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: iscsi: Avoid potential deadlock in iscsi_if_rx func
scsi: iscsi: Fix a potential deadlock in the timeout handler
scsi: smartpqi: Update attribute name to `driver_version`
scsi: libsas: stop discovering if oob mode is disconnected
scsi: ufs: Disable autohibern8 feature in Cadence UFS
scsi: iscsi: qla4xxx: fix double free in probe
scsi: ufs: Give an unique ID to each ufs-bsg
scsi: qla2xxx: Add debug dump of LOGO payload and ELS IOCB
scsi: qla2xxx: Ignore PORT UPDATE after N2N PLOGI
scsi: qla2xxx: Don't defer relogin unconditonally
scsi: qla2xxx: Send Notify ACK after N2N PLOGI
scsi: qla2xxx: Configure local loop for N2N target
scsi: qla2xxx: Fix PLOGI payload and ELS IOCB dump length
scsi: qla2xxx: Don't call qlt_async_event twice
scsi: qla2xxx: Allow PLOGI in target mode
scsi: qla2xxx: Change discovery state before PLOGI
scsi: qla2xxx: Drop superfluous INIT_WORK of del_work
scsi: qla2xxx: Initialize free_work before flushing it
scsi: qla2xxx: Use explicit LOGO in target mode
scsi: qla2xxx: Ignore NULL pointer in tcm_qla2xxx_free_mcmd
...
-----BEGIN PGP SIGNATURE-----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=hmxJ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20191212' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- stable fix for the bi_size overflow. Not a corruption issue, but a
case wher we could merge but disallowed (Andreas)
- NVMe pull request via Keith, with various fixes.
- MD pull request from Song.
- Merge window regression fix for the rq passthrough stats (Logan)
- Remove unused blkcg_drain_queue() function (Guoqing)
* tag 'for-linus-20191212' of git://git.kernel.dk/linux-block:
blk-cgroup: remove blkcg_drain_queue
block: fix NULL pointer dereference in account statistics with IDE
md: make sure desc_nr less than MD_SB_DISKS
md: raid1: check rdev before reference in raid1_sync_request func
raid5: need to set STRIPE_HANDLE for batch head
block: fix "check bi_size overflow before merge"
nvme/pci: Fix read queue count
nvme/pci Limit write queue sizes to possible cpus
nvme/pci: Fix write and poll queue types
nvme/pci: Remove last_cq_head
nvme: Namepace identification descriptor list is optional
nvme-fc: fix double-free scenarios on hw queues
nvme: else following return is not needed
nvme: add error message on mismatching controller ids
nvme_fc: add module to ops template to allow module references
nvmet-loop: Avoid preallocating big SGL for data
nvme-fc: Avoid preallocating big SGL for data
nvme-rdma: Avoid preallocating big SGL for data
Some time ago the block layer was modified such that timeout handlers are
called from thread context instead of interrupt context. Make it safe to
run the iSCSI timeout handler in thread context. This patch fixes the
following lockdep complaint:
================================
WARNING: inconsistent lock state
5.5.1-dbg+ #11 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/7:1H/206 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff88802d9827e8 (&(&session->frwd_lock)->rlock){+.?.}, at: iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
{IN-SOFTIRQ-W} state was registered at:
lock_acquire+0x106/0x240
_raw_spin_lock+0x38/0x50
iscsi_check_transport_timeouts+0x3e/0x210 [libiscsi]
call_timer_fn+0x132/0x470
__run_timers.part.0+0x39f/0x5b0
run_timer_softirq+0x63/0xc0
__do_softirq+0x12d/0x5fd
irq_exit+0xb3/0x110
smp_apic_timer_interrupt+0x131/0x3d0
apic_timer_interrupt+0xf/0x20
default_idle+0x31/0x230
arch_cpu_idle+0x13/0x20
default_idle_call+0x53/0x60
do_idle+0x38a/0x3f0
cpu_startup_entry+0x24/0x30
start_secondary+0x222/0x290
secondary_startup_64+0xa4/0xb0
irq event stamp: 1383705
hardirqs last enabled at (1383705): [<ffffffff81aace5c>] _raw_spin_unlock_irq+0x2c/0x50
hardirqs last disabled at (1383704): [<ffffffff81aacb98>] _raw_spin_lock_irq+0x18/0x50
softirqs last enabled at (1383690): [<ffffffffa0e2efea>] iscsi_queuecommand+0x76a/0xa20 [libiscsi]
softirqs last disabled at (1383682): [<ffffffffa0e2e998>] iscsi_queuecommand+0x118/0xa20 [libiscsi]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&session->frwd_lock)->rlock);
<Interrupt>
lock(&(&session->frwd_lock)->rlock);
*** DEADLOCK ***
2 locks held by kworker/7:1H/206:
#0: ffff8880d57bf928 ((wq_completion)kblockd){+.+.}, at: process_one_work+0x472/0xab0
#1: ffff88802b9c7de8 ((work_completion)(&q->timeout_work)){+.+.}, at: process_one_work+0x476/0xab0
stack backtrace:
CPU: 7 PID: 206 Comm: kworker/7:1H Not tainted 5.5.1-dbg+ #11
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
dump_stack+0xa5/0xe6
print_usage_bug.cold+0x232/0x23b
mark_lock+0x8dc/0xa70
__lock_acquire+0xcea/0x2af0
lock_acquire+0x106/0x240
_raw_spin_lock+0x38/0x50
iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
scsi_times_out+0xf4/0x440 [scsi_mod]
scsi_timeout+0x1d/0x20 [scsi_mod]
blk_mq_check_expired+0x365/0x3a0
bt_iter+0xd6/0xf0
blk_mq_queue_tag_busy_iter+0x3de/0x650
blk_mq_timeout_work+0x1af/0x380
process_one_work+0x56d/0xab0
worker_thread+0x7a/0x5d0
kthread+0x1bc/0x210
ret_from_fork+0x24/0x30
Fixes: 287922eb0b ("block: defer timeouts to a workqueue")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191209173457.187370-1-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch disables autohibern8 feature in Cadence UFS. The autohibern8
feature has issues due to which unexpected interrupt trigger is happening.
After the interrupt issue is sorted out, autohibern8 feature will be
re-enabled
Link: https://lore.kernel.org/r/1575367635-22662-1-git-send-email-sheebab@cadence.com
Cc: <stable@vger.kernel.org>
Signed-off-by: sheebab <sheebab@cadence.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On this error path we call qla4xxx_mem_free() and then the caller also
calls qla4xxx_free_adapter() which calls qla4xxx_mem_free(). It leads to a
couple double frees:
drivers/scsi/qla4xxx/ql4_os.c:8856 qla4xxx_probe_adapter() warn: 'ha->chap_dma_pool' double freed
drivers/scsi/qla4xxx/ql4_os.c:8856 qla4xxx_probe_adapter() warn: 'ha->fw_ddb_dma_pool' double freed
Fixes: afaf5a2d34 ("[SCSI] Initial Commit of qla4xxx")
Link: https://lore.kernel.org/r/20191203094421.hw7ex7qr3j2rbsmx@kili.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Considering there can be multiple UFS hosts in SoC, give each ufs-bsg an
unique ID by appending the scsi host number to its device name.
Link: https://lore.kernel.org/r/0101016eca8dc9d7-d24468d3-04d2-4ef3-a906-abe8b8cbcd3d-000000@us-west-2.amazonses.com
Fixes: df032bf27a ("scsi: ufs: Add a bsg endpoint that supports UPIUs")
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change adds a way to debug LOGO ELS, likewise PLOGI.
Link: https://lore.kernel.org/r/20191125165702.1013-14-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Acked-by: Quinn Tran <qutran@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PORT UPDATE asynchronous event is generated on the host that issues PLOGI
ELS (in the case of higher WWPN). In that case, the event shouldn't be
handled as it sets unwanted DPC flags (i.e. LOOP_RESYNC_NEEDED) that
trigger link flap.
Ignore the event if the host has higher WWPN, but handle otherwise.
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-13-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2x00_configure_local_loop sets RELOGIN_NEEDED bit and calls
qla24xx_fcport_handle_login to perform the login. This bit triggers a wake
up of DPC later after a successful login.
The deferred call is not needed if login succeeds, and it's set in
qla24xx_fcport_handle_login in case of errors, hence it should be safe to
drop.
Link: https://lore.kernel.org/r/20191125165702.1013-12-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Acked-by: Quinn Tran <qutran@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qlt_handle_login schedules session for deletion even if a login is in
progress. That causes login bouncing, i.e. a few logins are made before it
settles down.
Complete the first login by sending Notify Acknowledge IOCB via
qlt_plogi_ack_unref if the session is pending login completion.
Fixes: 9cd883f07a ("scsi: qla2xxx: Fix session cleanup for N2N")
Cc: Krishna Kant <krishna.kant@purestorage.com>
Cc: Alexei Potashnik <alexei@purestorage.com>
Link: https://lore.kernel.org/r/20191125165702.1013-11-r.bolshakov@yadro.com
Acked-by: Quinn Tran <qutran@marvell.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2x00_configure_local_loop initializes PLOGI payload for PLOGI ELS using
Get Parameters mailbox command.
In the case when the driver is running in target mode, the topology is N2N
and the target port has higher WWPN, LOCAL_LOOP_UPDATE bit is cleared too
early and PLOGI payload is not initialized by the Get Parameters
command. That causes a failure of ELS IOCB carrying the PLOGI with 0x15 aka
Data Underrun error.
LOCAL_LOOP_UPDATE has to be set to initialize PLOGI payload.
Fixes: 48acad0990 ("scsi: qla2xxx: Fix N2N link re-connect")
Link: https://lore.kernel.org/r/20191125165702.1013-10-r.bolshakov@yadro.com
Acked-by: Quinn Tran <qutran@marvell.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The size of the buffer is hardcoded as 0x70 or 112 bytes, while the size of
ELS IOCB is 0x40 and the size of PLOGI payload returned by Get Parameters
command is 0x74.
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-9-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MBA_PORT_UPDATE generates duplicate log lines in target mode because
qlt_async_event is called twice. Drop the calls within the case as the
function will be called right after the switch statement.
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-8-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvel.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to FC-LS-3 (Fibre Channel Link Services) 6.3.2.4
"N_Port Login - No Fabric present", if both parties in the point-to-point
connection know N_Port_Names of each other, Nx_Port with the highest
N_Port_name shall transmit PLOGI. The specification sets no restrictions on
the port role that should send PLOGI.
However, FCP-4 (Fibre Channel Protocol for SCSI, Fourth Version) 6.2
"Overview of Process Login and Process Logout", instructs that in
point-to-point topology, initiator shall send explicit PRLI ELS.
The change fixes stuck P2P login, when target WWPN is higher than initiator
WWPN.
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-7-r.bolshakov@yadro.com
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a port sends PLOGI, discovery state should be changed to login
pending, otherwise RELOGIN_NEEDED bit is set in
qla24xx_handle_plogi_done_event(). RELOGIN_NEEDED triggers another PLOGI,
and it never goes out of the loop until login timer expires.
Fixes: 8777e4314d ("scsi: qla2xxx: Migrate NVME N2N handling into state machine")
Fixes: 8b5292bcfc ("scsi: qla2xxx: Fix Relogin to prevent modifying scan_state flag")
Cc: Quinn Tran <qutran@marvell.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191125165702.1013-6-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
del_work is already initialized inside qla2x00_alloc_fcport, there's no
need to overwrite it. Indeed, it might prevent complete traversal of
workqueue list.
Fixes: a01c77d2cb ("scsi: qla2xxx: Move session delete to driver work queue")
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-5-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Target makes implicit LOGO on session teardown. LOGO ELS is not send on the
wire and initiator is not aware that target no longer wants talking to
it. Initiator keeps sending I/O requests, target responds with BA_RJT, they
time out and then initiator sends ABORT TASK (ABTS-LS).
Current behaviour incurs unneeded I/O timeout and can be fixed for some
initiators by making explicit LOGO on session deletion.
Link: https://lore.kernel.org/r/20191125165702.1013-3-r.bolshakov@yadro.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If ABTS cannot be completed in target mode, the driver attempts to free
related management command and crashes:
NIP [d000000019181ee8] tcm_qla2xxx_free_mcmd+0x40/0x80 [tcm_qla2xxx]
LR [d00000001dc1e6f8] qlt_response_pkt+0x190/0xa10 [qla2xxx]
Call Trace:
[c000003fff27bb50] [c000003fff27bc10] 0xc000003fff27bc10 (unreliable)
[c000003fff27bb70] [d00000001dc1e6f8] qlt_response_pkt+0x190/0xa10 [qla2xxx]
[c000003fff27bc10] [d00000001dbc2be0] qla24xx_process_response_queue+0x5d8/0xbd0 [qla2xxx]
[c000003fff27bd50] [d00000001dbc632c] qla24xx_msix_rsp_q+0x64/0x150 [qla2xxx]
[c000003fff27bde0] [c000000000187200] __handle_irq_event_percpu+0x90/0x310
[c000003fff27bea0] [c0000000001874b8] handle_irq_event_percpu+0x38/0x90
[c000003fff27bee0] [c000000000187574] handle_irq_event+0x64/0xb0
[c000003fff27bf10] [c00000000018cd38] handle_fasteoi_irq+0xe8/0x280
[c000003fff27bf40] [c000000000185ccc] generic_handle_irq+0x4c/0x70
[c000003fff27bf60] [c000000000016cec] __do_irq+0x7c/0x1d0
[c000003fff27bf90] [c00000000002a530] call_do_irq+0x14/0x24
[c00000207d2cba90] [c000000000016edc] do_IRQ+0x9c/0x130
[c00000207d2cbae0] [c000000000008bf4] hardware_interrupt_common+0x114/0x120
--- interrupt: 501 at arch_local_irq_restore+0x74/0x90
LR = arch_local_irq_restore+0x74/0x90
[c00000207d2cbdd0] [c0000000001c64fc] tick_broadcast_oneshot_control+0x4c/0x60 (unreliable)
[c00000207d2cbdf0] [c0000000007ac840] cpuidle_enter_state+0xf0/0x450
[c00000207d2cbe50] [c00000000016b81c] call_cpuidle+0x4c/0x90
[c00000207d2cbe70] [c00000000016bc30] do_idle+0x2b0/0x330
[c00000207d2cbec0] [c00000000016beec] cpu_startup_entry+0x3c/0x50
[c00000207d2cbef0] [c00000000004a06c] start_secondary+0x63c/0x670
[c00000207d2cbf90] [c00000000000aa6c] start_secondary_prolog+0x10/0x14
The crash can be triggered by ACL deletion when there's active I/O.
During ACL deletion, qla2xxx performs implicit LOGO that's invisible for
the initiator. Only the driver and firmware are aware of the logout.
Therefore the initiator continues to send SCSI commands and the target
always responds with SAM STATUS BUSY as it can't find the session.
The command times out after a while and initiator invokes ABORT TASK TMF
for the command. The TMF is mapped to ABTS-LS in FCP. The target can't find
session for S_ID originating ABTS-LS so it never allocates mcmd. And since
N_Port handle was deleted after LOGO, it is no longer valid and ABTS
Response IOCB is returned from firmware with status 31. Then free_mcmd is
invoked on NULL pointer and the kernel crashes.
[ 7734.578642] qla2xxx [0000:00:0c.0]-e837:6: ABTS_RECV_24XX: instance 0
[ 7734.578644] qla2xxx [0000:00:0c.0]-f811:6: qla_target(0): task abort (s_id=1:2:0, tag=1209504, param=0)
[ 7734.578645] find_sess_by_s_id: 0x010200
[ 7734.578645] Unable to locate s_id: 0x010200
[ 7734.578646] qla2xxx [0000:00:0c.0]-f812:6: qla_target(0): task abort for non-existent session
[ 7734.578648] qla2xxx [0000:00:0c.0]-e806:6: Sending task mgmt ABTS response (ha=c0000000d5819000, atio=c0000000d3fd4700, status=4
[ 7734.578730] qla2xxx [0000:00:0c.0]-e838:6: ABTS_RESP_24XX: compl_status 31
[ 7734.578732] qla2xxx [0000:00:0c.0]-e863:6: qla_target(0): ABTS_RESP_24XX failed 31 (subcode 19:a)
[ 7734.578740] Unable to handle kernel paging request for data at address 0x00000200
Fixes: 6b0431d6fa ("scsi: qla2xxx: Fix out of order Termination and ABTS response")
Cc: Quinn Tran <qutran@marvell.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Thomas Abraham <tabraham@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191125165702.1013-2-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When phba->mbox_ext_buf_ctx.seqNum != phba->mbox_ext_buf_ctx.numBuf,
dd_data should be freed before return SLI_CONFIG_HANDLED.
When lpfc_sli_issue_mbox func return fails, pmboxq should be also freed in
job_error tag.
Link: https://lore.kernel.org/r/EDBAAA0BBBA2AC4E9C8B6B81DEEE1D6915E7A966@DGGEML525-MBS.china.huawei.com
Signed-off-by: Bo Wu <wubo40@huawei.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SFUB length should be in DWORDs when passed to FW.
Fixes: 3f006ac342 ("scsi: qla2xxx: Secure flash update support for ISP28XX")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191203223657.22109-4-hmadhani@marvell.com
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for MPI/PEP region updates which is required with
secure flash updates for ISP28XX.
Fixes: 3f006ac342 ("scsi: qla2xxx: Secure flash update support for ISP28XX")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191203223657.22109-3-hmadhani@marvell.com
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
11 patches, all in drivers (no core changes) that are either minor
cleanups or small fixes. They were late arriving, but still safe for
-rc1.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXeyDEiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbijAQDIuM45
xeEXgWXF8c/tYuvildK1WjyVzwBO2k563lUmYQEA4rxSzkmhtcaMTDuk4hI4Y4TP
p87U1bXNSJ7tCpFU15w=
=W43H
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Eleven patches, all in drivers (no core changes) that are either minor
cleanups or small fixes.
They were late arriving, but still safe for -rc1"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
scsi: megaraid_sas: Make poll_aen_lock static
scsi: sd_zbc: Improve report zones error printout
scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
scsi: qla2xxx: unregister ports after GPN_FT failure
scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
scsi: pm80xx: Remove unused include of linux/version.h
scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
scsi: scsi_transport_sas: Fix memory leak when removing devices
scsi: lpfc: size cpu map by last cpu id set
scsi: ibmvscsi_tgt: Remove unneeded variable rc
Pull NVMe fixes from Keith
* 'nvme/for-5.5' of git://git.infradead.org/nvme:
nvme/pci: Fix read queue count
nvme/pci Limit write queue sizes to possible cpus
nvme/pci: Fix write and poll queue types
nvme/pci: Remove last_cq_head
nvme: Namepace identification descriptor list is optional
nvme-fc: fix double-free scenarios on hw queues
nvme: else following return is not needed
nvme: add error message on mismatching controller ids
nvme_fc: add module to ops template to allow module references
nvmet-loop: Avoid preallocating big SGL for data
nvme-fc: Avoid preallocating big SGL for data
nvme-rdma: Avoid preallocating big SGL for data
-----BEGIN PGP SIGNATURE-----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=7ZFw
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20191205' of git://git.kernel.dk/linux-block
Pull more block and io_uring updates from Jens Axboe:
"I wasn't expecting this to be so big, and if I was, I would have used
separate branches for this. Going forward I'll be doing separate
branches for the current tree, just like for the next kernel version
tree. In any case, this contains:
- Series from Christoph that fixes an inherent race condition with
zoned devices and revalidation.
- null_blk zone size fix (Damien)
- Fix for a regression in this merge window that caused busy spins by
sending empty disk uevents (Eric)
- Fix for a regression in this merge window for bfq stats (Hou)
- Fix for io_uring creds allocation failure handling (me)
- io_uring -ERESTARTSYS send/recvmsg fix (me)
- Series that fixes the need for applications to retain state across
async request punts for io_uring. This one is a bit larger than I
would have hoped, but I think it's important we get this fixed for
5.5.
- connect(2) improvement for io_uring, handling EINPROGRESS instead
of having applications needing to poll for it (me)
- Have io_uring use a hash for poll requests instead of an rbtree.
This turned out to work much better in practice, so I think we
should make the switch now. For some workloads, even with a fair
amount of cancellations, the insertion sort is just too expensive.
(me)
- Various little io_uring fixes (me, Jackie, Pavel, LimingWu)
- Fix for brd unaligned IO, and a warning for the future (Ming)
- Fix for a bio integrity data leak (Justin)
- bvec_iter_advance() improvement (Pavel)
- Xen blkback page unmap fix (SeongJae)
The major items in here are all well tested, and on the liburing side
we continue to add regression and feature test cases. We're up to 50
topic cases now, each with anywhere from 1 to more than 10 cases in
each"
* tag 'for-linus-20191205' of git://git.kernel.dk/linux-block: (33 commits)
block: fix memleak of bio integrity data
io_uring: fix a typo in a comment
bfq-iosched: Ensure bio->bi_blkg is valid before using it
io_uring: hook all linked requests via link_list
io_uring: fix error handling in io_queue_link_head
io_uring: use hash table for poll command lookups
io-wq: clear node->next on list deletion
io_uring: ensure deferred timeouts copy necessary data
io_uring: allow IO_SQE_* flags on IORING_OP_TIMEOUT
null_blk: remove unused variable warning on !CONFIG_BLK_DEV_ZONED
brd: warn on un-aligned buffer
brd: remove max_hw_sectors queue limit
xen/blkback: Avoid unmapping unmapped grant pages
io_uring: handle connect -EINPROGRESS like -EAGAIN
block: set the zone size in blk_revalidate_disk_zones atomically
block: don't handle bio based drivers in blk_revalidate_disk_zones
block: allocate the zone bitmaps lazily
block: replace seq_zones_bitmap with conv_zones_bitmap
block: simplify blkdev_nr_zones
block: remove the empty line at the end of blk-zoned.c
...
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
The current zone revalidation code has a major problem in that it
doesn't update the zone size and q->nr_zones atomically, leading
to a short window where an out of bounds access to the zone arrays
is possible.
To fix this move the setting of the zone size into the crticial
sections blk_revalidate_disk_zones so that it gets updated together
with the zone bitmaps and q->nr_zones. This also slightly simplifies
the caller as it deducts the zone size from the report_zones.
This change also allows to check for a power of two zone size in generic
code.
Reported-by: Hans Holmberg <hans@owltronix.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is mostly update of the usual drivers: aacraid, ufs, zfcp,
NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx
plus a whole load of minor updates and fixes. The two major core
changes are Al Viro's reworking of sg's handling of copy to/from user,
Ming Lei's removal of the host busy counter to avoid contention in the
multiqueue case and Damien Le Moal's fixing of residual tracking
across error handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXeKvHCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQJMAQDAjlAi
SNfbyndMqyf+rZGWufDI+43Up1VvW9GeWJHeDwEAxfO5XZsCks2uT8UxXhpEp9L7
HkiUww3zbcgl0FWFkUM=
=cdVU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: aacraid, ufs, zfcp,
NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx
plus a whole load of minor updates and fixes.
The major core changes are Al Viro's reworking of sg's handling of
copy to/from user, Ming Lei's removal of the host busy counter to
avoid contention in the multiqueue case and Damien Le Moal's fixing of
residual tracking across error handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (251 commits)
scsi: bnx2fc: timeout calculation invalid for bnx2fc_eh_abort()
scsi: target: core: Fix a pr_debug() argument
scsi: iscsi: Don't send data to unbound connection
scsi: target: iscsi: Wait for all commands to finish before freeing a session
scsi: target: core: Release SPC-2 reservations when closing a session
scsi: target: core: Document target_cmd_size_check()
scsi: bnx2i: fix potential use after free
Revert "scsi: qla2xxx: Fix memory leak when sending I/O fails"
scsi: NCR5380: Add disconnect_mask module parameter
scsi: NCR5380: Unconditionally clear ICR after do_abort()
scsi: NCR5380: Call scsi_set_resid() on command completion
scsi: scsi_debug: num_tgts must be >= 0
scsi: lpfc: use hdwq assigned cpu for allocation
scsi: arcmsr: fix indentation issues
scsi: qla4xxx: fix double free bug
scsi: pm80xx: Modified the logic to collect fatal dump
scsi: pm80xx: Tie the interrupt name to the module instance
scsi: pm80xx: Controller fatal error through sysfs
scsi: pm80xx: Do not request 12G sas speeds
scsi: pm80xx: Cleanup command when a reset times out
...
-----BEGIN PGP SIGNATURE-----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=hnf4
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20191129' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"I wasn't going to send this one off so soon, but unfortunately one of
the fixes from the previous pull broke the build on some archs. So I'm
sending this sooner rather than later. This contains:
- Add highmem.h include for io_uring, because of the kmap() additions
from last round. For some reason the build bot didn't spot this
even though it sat for days.
- Three minor ';' removals
- Add support for the Beurer CD-on-a-chip device
- Make io_uring work on MMU-less archs"
* tag 'for-linus-20191129' of git://git.kernel.dk/linux-block:
io_uring: fix missing kmap() declaration on powerpc
ataflop: Remove unneeded semicolon
block: sunvdc: Remove unneeded semicolon
drbd: Remove unneeded semicolon
io_uring: add mapping support for NOMMU archs
sr_vendor: support Beurer GL50 evo CD-on-a-chip devices.
cdrom: respect device capabilities during opening action
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
- Hibernation support (Dexuan Cui).
- Latency testing framework (Branden Bonaby).
- Decoupling Hyper-V page size from guest page size (Himadri Pandya).
-----BEGIN PGP SIGNATURE-----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=oJGE
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Sasha Levin:
- support for new VMBus protocols (Andrea Parri)
- hibernation support (Dexuan Cui)
- latency testing framework (Branden Bonaby)
- decoupling Hyper-V page size from guest page size (Himadri Pandya)
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (22 commits)
Drivers: hv: vmbus: Fix crash handler reset of Hyper-V synic
drivers/hv: Replace binary semaphore with mutex
drivers: iommu: hyperv: Make HYPERV_IOMMU only available on x86
HID: hyperv: Add the support of hibernation
hv_balloon: Add the support of hibernation
x86/hyperv: Implement hv_is_hibernation_supported()
Drivers: hv: balloon: Remove dependencies on guest page size
Drivers: hv: vmbus: Remove dependencies on guest page size
x86: hv: Add function to allocate zeroed page for Hyper-V
Drivers: hv: util: Specify ring buffer size using Hyper-V page size
Drivers: hv: Specify receive buffer size using Hyper-V page size
tools: hv: add vmbus testing tool
drivers: hv: vmbus: Introduce latency testing
video: hyperv: hyperv_fb: Support deferred IO for Hyper-V frame buffer driver
video: hyperv: hyperv_fb: Obtain screen resolution from Hyper-V host
hv_netvsc: Add the support of hibernation
hv_sock: Add the support of hibernation
video: hyperv_fb: Add the support of hibernation
scsi: storvsc: Add the support of hibernation
Drivers: hv: vmbus: Add module parameter to cap the VMBus version
...
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
Fix sparse warning:
drivers/scsi/megaraid/megaraid_sas_base.c:187:12:
warning: symbol 'poll_aen_lock' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20191125144454.22680-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the case of a report zones command failure, instead of simply printing
the host_byte and driver_byte values returned, print a message that is more
human readable and useful, adding sense codes too.
To do so, use the already defined sd_print_sense_hdr() and
sd_print_result() functions by moving the declaration of these functions
into sd.h.
Link: https://lore.kernel.org/r/20191125070518.951717-1-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 4fa1834559 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/
pci_free_irq_vectors calls.") use pci_alloc_irq_vectors() to replace
pci_enable_msi() but it didn't handle the return value correctly. This bug
make qla2x00 always fail to setup MSI if MSI-X fail, so fix it.
BTW, improve the log message of return value in qla2x00_request_irqs() to
avoid confusion.
Fixes: 4fa1834559 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls.")
Cc: Michael Hernandez <michael.hernandez@cavium.com>
Link: https://lore.kernel.org/r/1574314847-14280-1-git-send-email-chenhc@lemote.com
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When ports are lost due to unzoning them, and the initiator port is
not part of any more zones, the GPN_FT command used for the fabric
scan may fail. In this case, the current code simply gives up after a
few retries. But if the zone is gone, all rports should actually be
marked as lost.
Fix this by jumping to the code that handles logout after GNN_FT after
scan retries are exhausted.
Fixes: f352eeb754 ("scsi: qla2xxx: Add ability to use GPNFT/GNNFT for RSCN handling")
Link: https://lore.kernel.org/r/20191122221912.20100-3-martin.wilck@suse.com
Tested-by: Jason Orendorf <orendorf@hpe.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In qla2x00_find_all_fabric_devs(), fcport->flags & FCF_LOGIN_NEEDED is a
necessary condition for logging into new rports, but not for dropping lost
ones.
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Link: https://lore.kernel.org/r/20191122221912.20100-2-martin.wilck@suse.com
Tested-by: David Bond <dbond@suse.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove #include <linux/version.h>. Don't need it.
Link: https://lore.kernel.org/r/20191122020911.33269-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The condition (reg_val != 2) || (reg_val != 3) will always be true because
reg_val cannot be equal to two different values at the same time. Fix this
by replacing the || operator with && so that the loop will loop if reg_val
is not a 2 and not a 3 as was originally intended.
Fixes: 50dc2f221455 ("scsi: pm80xx: Modified the logic to collect fatal dump")
Link: https://lore.kernel.org/r/20191120135031.270708-1-colin.king@canonical.com
Addresses-Coverity: ("Constant expression result")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle were:
- Dynamic tick (nohz) updates, perhaps most notably changes to force
the tick on when needed due to lengthy in-kernel execution on CPUs
on which RCU is waiting.
- Linux-kernel memory consistency model updates.
- Replace rcu_swap_protected() with rcu_prepace_pointer().
- Torture-test updates.
- Documentation updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
security/safesetid: Replace rcu_swap_protected() with rcu_replace_pointer()
net/sched: Replace rcu_swap_protected() with rcu_replace_pointer()
net/netfilter: Replace rcu_swap_protected() with rcu_replace_pointer()
net/core: Replace rcu_swap_protected() with rcu_replace_pointer()
bpf/cgroup: Replace rcu_swap_protected() with rcu_replace_pointer()
fs/afs: Replace rcu_swap_protected() with rcu_replace_pointer()
drivers/scsi: Replace rcu_swap_protected() with rcu_replace_pointer()
drm/i915: Replace rcu_swap_protected() with rcu_replace_pointer()
x86/kvm/pmu: Replace rcu_swap_protected() with rcu_replace_pointer()
rcu: Upgrade rcu_swap_protected() to rcu_replace_pointer()
rcu: Suppress levelspread uninitialized messages
rcu: Fix uninitialized variable in nocb_gp_wait()
rcu: Update descriptions for rcu_future_grace_period tracepoint
rcu: Update descriptions for rcu_nocb_wake tracepoint
rcu: Remove obsolete descriptions for rcu_barrier tracepoint
rcu: Ensure that ->rcu_urgent_qs is set before resched IPI
workqueue: Convert for_each_wq to use built-in list check
rcu: Several rcu_segcblist functions can be static
rcu: Remove unused function hlist_bl_del_init_rcu()
Documentation: Rename rcu_node_context_switch() to rcu_note_context_switch()
...
The Beurer GL50 evo uses a Cygnal-manufactured CD-on-a-chip that only
accepts a subset of SCSI commands, and supports neither audio commands
nor generic packet commands.
Actually sending those commands bring the device to an unrecoverable
state that causes the device to hang and reset.
To: Jens Axboe <axboe@kernel.dk>
Cc: linux-kernel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In nvme-fc: it's possible to have connected active controllers
and as no references are taken on the LLDD, the LLDD can be
unloaded. The controller would enter a reconnect state and as
long as the LLDD resumed within the reconnect timeout, the
controller would resume. But if a namespace on the controller
is the root device, allowing the driver to unload can be problematic.
To reload the driver, it may require new io to the boot device,
and as it's no longer connected we get into a catch-22 that
eventually fails, and the system locks up.
Fix this issue by taking a module reference for every connected
controller (which is what the core layer did to the transport
module). Reference is cleared when the controller is removed.
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
-----BEGIN PGP SIGNATURE-----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=QCEy
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow to print symbolic error names via new %pe modifier.
- Use pr_warn() instead of the remaining pr_warning() calls. Fix
formatting of the related lines.
- Add VSPRINTF entry to MAINTAINERS.
* tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: (32 commits)
checkpatch: don't warn about new vsprintf pointer extension '%pe'
MAINTAINERS: Add VSPRINTF
tools lib api: Renaming pr_warning to pr_warn
ASoC: samsung: Use pr_warn instead of pr_warning
lib: cpu_rmap: Use pr_warn instead of pr_warning
trace: Use pr_warn instead of pr_warning
dma-debug: Use pr_warn instead of pr_warning
vgacon: Use pr_warn instead of pr_warning
fs: afs: Use pr_warn instead of pr_warning
sh/intc: Use pr_warn instead of pr_warning
scsi: Use pr_warn instead of pr_warning
platform/x86: intel_oaktrail: Use pr_warn instead of pr_warning
platform/x86: asus-laptop: Use pr_warn instead of pr_warning
platform/x86: eeepc-laptop: Use pr_warn instead of pr_warning
oprofile: Use pr_warn instead of pr_warning
of: Use pr_warn instead of pr_warning
macintosh: Use pr_warn instead of pr_warning
idsn: Use pr_warn instead of pr_warning
ide: Use pr_warn instead of pr_warning
crypto: n2: Use pr_warn instead of pr_warning
...
Currently the lpfc driver sizes its cpu_map array based on
num_possible_cpus(). However, that can be a value that is less than the
highest cpu id bit that is set. As such, if a thread runs on a cpu with a
larger cpu id, or for_each_possible_cpu() is used, the driver could index
off the end of the array and return garbage or GPF.
The driver maintains its own internal copy of the "num_possible" cpu value
and sizes arrays by it.
Fix by setting the driver's value to the value of the last cpu id bit set
in the possible_mask - plus 1. Thus cpu_map will be sized to allow access
by any cpu id possible.
Link: https://lore.kernel.org/r/20191121175556.18953-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable rc is not modified in ibmvscsis_srp_i_logout function. So remove
unneeded variable rc.
Issue found using coccicheck tool.
Link: https://lore.kernel.org/r/20191101120407.GA9369@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we're in storvsc_suspend(), we're sure the SCSI layer has quiesced the
scsi device by scsi_bus_suspend() -> ... -> scsi_device_quiesce(), so the
low level SCSI adapter driver only needs to suspend/resume its own state.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
In the bnx2fc_eh_abort() function there is a calculation for
wait_for_completion that uses a HZ multiplier. This is incorrect, it
scales the timeout by 1000 seconds instead of converting the ms value to
jiffies. Therefore change the calculation.
Link: https://lore.kernel.org/r/1574178394-16635-1-git-send-email-loberman@redhat.com
Reported-by: David Jeffery <djeffery@redhat.com>
Reviewed-by: John Pittman <jpittman@redhat.com>
Reviewed-by: Chad Dupuis <cdupuis1@gmail.com>
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The member hba->pcidev may be used after its reference is dropped. Move the
put function to where it is never used to avoid potential use after free
issues.
Fixes: a771718065 ("[SCSI] bnx2i: Removed the reference to the netdev->base_addr")
Link: https://lore.kernel.org/r/1573043541-19126-1-git-send-email-bianpan2016@163.com
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 2f856d4e8c.
This patch was found to introduce a double free regression. The issue
it originally attempted to address was fixed in patch
f45bca8c50 ("scsi: qla2xxx: Fix double scsi_done for abort path").
Link: https://lore.kernel.org/r/4BDE2B95-835F-43BE-A32C-2629D7E03E0A@marvell.com
Requested-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a module parameter to inhibit disconnect/reselect for individual
targets. This gains compatibility with Aztec PowerMonster SCSI/SATA
adapters with buggy firmware. (No fix is available from the vendor.)
Apparently these adapters pass-through the product/vendor of the attached
SATA device. Since they can't be identified from the response to an INQUIRY
command, a device blacklist flag won't work.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Link: https://lore.kernel.org/r/993b17545990f31f9fa5a98202b51102a68e7594.1573875417.git.fthain@telegraphics.com.au
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When do_abort() succeeds, the target will go to BUS FREE phase and there
will be no connected command. Therefore, that function should clear the
Initiator Command Register before returning. It already does so in case of
NCR5380_poll_politely() failure; do the same for the other error case too,
that is, NCR5380_transfer_pio() failure.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Ondrej Zary <linux@zary.sk>
Link: https://lore.kernel.org/r/4277b28ee2551f884aefa85965ef3c498344f301.1573875417.git.fthain@telegraphics.com.au
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most NCR5380 drivers calculate the residual for every data transfer.
(A few drivers just set it to zero.) Pass this quantity back to the scsi
mid-layer on command completion.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Ondrej Zary <linux@zary.sk>
Link: https://lore.kernel.org/r/1f26ead9dd0dc053fcd27979d69a7ca74b6589b4.1573875417.git.fthain@telegraphics.com.au
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Passing the parameter "num_tgts=-1" will start an infinite loop that
exhausts the system memory
Link: https://lore.kernel.org/r/20191115163727.24626-1-mlombard@redhat.com
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Looking at the recent conversion from smp_processor_id() to
raw_smp_processor_id(), realized that the allocation should be based on the
cpu the hdwq is bound to, not the executing cpu.
Revise to pull cpu number from the hdwq
Fixes: 765ab6cdac ("scsi: lpfc: Fix a kernel warning triggered by lpfc_get_sgl_per_hdwq()")
Link: https://lore.kernel.org/r/20191116003847.6141-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable init_fw_cb is released twice, resulting in a double free
bug. The call to the function dma_free_coherent() before goto is removed to
get rid of potential double free.
Fixes: 2a49a78ed3 ("[SCSI] qla4xxx: added IPv6 support.")
Link: https://lore.kernel.org/r/1572945927-27796-1-git-send-email-bianpan2016@163.com
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the correct method to collect the fatal dump.
Link: https://lore.kernel.org/r/20191114100910.6153-14-deepak.ukey@microchip.com
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With MSI-x enabled, the interrupt instances are <prefix><index> where the
prefix is fixed for all module instances, making it a little harder to
track down what's what.
Link: https://lore.kernel.org/r/20191114100910.6153-13-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to check controller fatal error through sysfs.
Link: https://lore.kernel.org/r/20191114100910.6153-12-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Occasionally, 6G capable drives fail to train at 6G on links that look good
from a signal-integrity perspective. PMC suggests configuring the port to
not even expect 12G.
Link: https://lore.kernel.org/r/20191114100910.6153-11-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the fix so the if driver properly sent the abort it tries to remove
it from the firmware's list of outstanding commands regardless of the abort
status. This means that the task gets freed 'now' rather than possibly
getting freed later when the scsi layer thinks it's leaked but still valid.
Link: https://lore.kernel.org/r/20191114100910.6153-10-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The commands to the controller are sent in fixed sized chunks which are set
per-chip-generation and stashed in iomb_size. The driver fills in structs
matching the register layout and memcpy this to memory shared with the
controller. However, there are two problem cases:
1) Things like phy_start_req are too large because they share the
sas_identify_frame definition with libsas, and it includes the crc
word. This means that it's overwriting the start of the next
command block, that's ok except if it happens at the end of the
shared memory area.
2) Things like set_nvm_data_req which are shared between the HAL
layers. This means that it's sending 'random' data for things that
are in the reserved area. So far we haven't found a case where the
controller FW cares, but sending possible gibberish (for most of
the structures this is in the reserved area so previously zeroed)
is not recommended.
Link: https://lore.kernel.org/r/20191114100910.6153-9-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_task structure should not be used after task_done is called. If the
device is gone or not attached, we call task_done on t and continue to use
in the sas_task in rest of the function. task_done is pointing to
sas_ata_task_done, may free the memory associated with the task before
returning.
Link: https://lore.kernel.org/r/20191114100910.6153-8-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function mpi_uninit_check takes longer for inbound doorbell register to
be cleared. Increased the timeout substantially so that the driver does not
fail to load.
Link: https://lore.kernel.org/r/20191114100910.6153-7-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: ianyar <ianyar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The default logging doesn't include the device name, so it's difficult to
determine which controller is being logged about in error scenarios. The
logging level was only settable via sysfs, which made it inconvenient for
actual debugging. This changes the default to only cover error handling.
Link: https://lore.kernel.org/r/20191114100910.6153-6-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For delays longer than 20ms [um]delay isn't recommended.
pm80xx_chip_soft_rst starts off with a 500ms delay before it even gets
around to checking for the results of the reset. As long as it's at least
500ms it doesn't matter what the scheduler is doing. The delay in the
pm8001_exec_internal_task_abort does nothing, and theory is this is a delay
to avoid a double-free.
Link: https://lore.kernel.org/r/20191114100910.6153-5-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm8001_task_exec(), if the PHY is down, then we return the current value
of 'rc'. We need to make sure it's initialized.
Link: https://lore.kernel.org/r/20191114100910.6153-4-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After the completing the mpi_phy_start_resp, make phy enable completion as
NULL.
Link: https://lore.kernel.org/r/20191114100910.6153-3-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was missing complete() call in mpi_sata_completion which result in
SATA abort error handling timing out. That causes the device to be left in
the in_recovery state so subsequent commands sent to the device fail and
the OS removes access to it.
Link: https://lore.kernel.org/r/20191114100910.6153-2-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During clock gating (ufshcd_gate_work()), we first put the link hibern8 by
calling ufshcd_uic_hibern8_enter() and if ufshcd_uic_hibern8_enter()
returns success (0) then we gate all the clocks. Now let’s zoom in to what
ufshcd_uic_hibern8_enter() does internally: It calls
__ufshcd_uic_hibern8_enter() and if failure is encountered, link recovery
shall put the link back to the highest HS gear and returns success (0) to
ufshcd_uic_hibern8_enter() which is the issue as link is still in active
state due to recovery! Now ufshcd_uic_hibern8_enter() returns success to
ufshcd_gate_work() and hence it goes ahead with gating the UFS clock while
link is still in active state hence I believe controller would raise UIC
error interrupts. But when we service the interrupt, clocks might have
already been disabled!
This change fixes for this by returning failure from
__ufshcd_uic_hibern8_enter() if recovery succeeds as link is still not in
hibern8, upon receiving the error ufshcd_hibern8_enter() would initiate
retry to put the link state back into hibern8.
Link: https://lore.kernel.org/r/1573798172-20534-8-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change attempts to abort gating of clocks if a request to turn-on
clocks is pending. This would in turn avoid turning OFF and back ON the
clocks.
Link: https://lore.kernel.org/r/1573798172-20534-7-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return IRQ_HANDLED only if the irq is really handled, this will help in
catching spurious interrupts that go unhandled.
Link: https://lore.kernel.org/r/1573798172-20534-6-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_print_host_regs() can be called by interrupt handler, but it may
sleep due to ufshcd_dump_regs() allocates the dump buffer memory with flag
GFP_KERNEL. Fix it by changing GFP_KERNEL to GFP_ATMOIC.
Link: https://lore.kernel.org/r/1573798172-20534-5-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix up possible unclocked register access to auto hibern8 register in
resume path and through sysfs entry. Meanwhile, enable auto hibern8 only
after device is fully initialized in probe path.
Link: https://lore.kernel.org/r/1573798172-20534-4-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add reset control for host controller so that host controller can be reset
as required in its power up sequence.
Link: https://lore.kernel.org/r/1573798172-20534-3-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to recover from hibern8 exit failure, perform a reset in link
recovery path before issuing link start-up.
Link: https://lore.kernel.org/r/1573798172-20534-2-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/sd_zbc.c: In function 'sd_zbc_check_zones':
drivers/scsi/sd_zbc.c:341:9: warning:
variable 'buflen' set but not used [-Wunused-but-set-variable]
It is not used since commit d9dd73087a ("block: Enhance
blk_revalidate_disk_zones()")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove SG_NONE and a related misleading comment. Update documentation.
This patch does not affect behaviour as zero initialization is redundant.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Viresh Kumar <vireshk@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: usb-storage@lists.one-eyed-alien.net
Link: https://lore.kernel.org/r/b4779b7a6563f6bd8d259ee457871c1c463c420e.1572656814.git.fthain@telegraphics.com.au
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For some reason this driver depends on !64BIT, but it can still be useful
to allow compile-testing on 64-bit machines.
Link: https://lore.kernel.org/r/20191105085609.2338-3-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The MODULE_LICENSE macro is unconditionally defined in module.h, no need to
ifdef its use.
Link: https://lore.kernel.org/r/20191105085609.2338-2-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
platform_get_irq() will call dev_err() itself on failure, so there is no
need for the driver to also do this. This is detected by coccinelle.
Link: https://lore.kernel.org/r/20191101140058.23212-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When using this driver on a Blizzard 1260, there were failures whenever DMA
transfers from the SCSI bus to memory of 65535 bytes were followed by a DMA
transfer of 1 byte. This caused the byte at offset 65535 to be overwritten
with 0xff. The Blizzard hardware can't handle single byte DMA transfers.
Besides this issue, limiting the DMA length to something that is not a
multiple of the page size is very inefficient on most file systems.
It seems this limit was chosen because the DMA transfer counter of the ESP
by default is 16 bits wide, thus limiting the length to 65535 bytes.
However, the value 0 means 65536 bytes, which is handled by the ESP and the
Blizzard just fine. It is also the default maximum used by esp_scsi when
drivers don't provide their own dma_length_limit() function.
The limit of 65536 bytes can be used by all boards except the Fastlane. The
old driver used a limit of 65532 bytes (0xfffc), which is reintroduced in
this patch.
Fixes: b7ded0e8b0 ("scsi: zorro_esp: Limit DMA transfers to 65535 bytes")
Link: https://lore.kernel.org/r/20191112175523.23145-1-jongk@linux-m68k.org
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/csiostor/csio_lnode.c: In function 'csio_ln_init':
drivers/scsi/csiostor/csio_lnode.c:1995:21: warning:
variable 'rln' set but not used [-Wunused-but-set-variable]
It is never used since introduction, so remove it.
Link: https://lore.kernel.org/r/20191029061530.98197-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function __ufshcd_query_descriptor(), in the event of an error
happening, we directly goto out_unlock and forget to invaliate
hba->dev_cmd.query.descriptor pointer. This results in this pointer still
valid in ufshcd_copy_query_response() for other query requests which go
through ufshcd_exec_raw_upiu_cmd(). This will cause __memcpy() crash and
system hangs. Log as shown below:
Unable to handle kernel paging request at virtual address
ffff000012233c40
Mem abort info:
ESR = 0x96000047
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000047
CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp = 0000000028cc735c
[ffff000012233c40] pgd=00000000bffff003, pud=00000000bfffe003,
pmd=00000000ba8b8003, pte=0000000000000000
Internal error: Oops: 96000047 [#2] PREEMPT SMP
...
Call trace:
__memcpy+0x74/0x180
ufshcd_issue_devman_upiu_cmd+0x250/0x3c0
ufshcd_exec_raw_upiu_cmd+0xfc/0x1a8
ufs_bsg_request+0x178/0x3b0
bsg_queue_rq+0xc0/0x118
blk_mq_dispatch_rq_list+0xb0/0x538
blk_mq_sched_dispatch_requests+0x18c/0x1d8
__blk_mq_run_hw_queue+0xb4/0x118
blk_mq_run_work_fn+0x28/0x38
process_one_work+0x1ec/0x470
worker_thread+0x48/0x458
kthread+0x130/0x138
ret_from_fork+0x10/0x1c
Code: 540000ab a8c12027 a88120c7 a8c12027 (a88120c7)
---[ end trace 793e1eb5dff69f2d ]---
note: kworker/0:2H[2054] exited with preempt_count 1
This patch is to move "descriptor = NULL" down to below the label
"out_unlock".
Fixes: d44a5f98bb49b2(ufs: query descriptor API)
Link: https://lore.kernel.org/r/20191112223436.27449-3-huobean@gmail.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print out returned response size and buffer size, while the front one is
bigger than the back one.
Link: https://lore.kernel.org/r/20191112223436.27449-2-huobean@gmail.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we call function hisi_sas_debugfs_exit() to remove debugfs_dir
before freeing interrupt irqs and destroying workqueue in the driver remove
path.
If a dump is triggered before function hisi_sas_debugfs_exit() but
debugfs_work may be called after it, so it may refer to already removed
debugfs_dir which will cause NULL pointer dereference.
To avoid it, put function hisi_sas_debugfs_exit() after free_irqs and
destroy workqueue when removing hisi_sas driver.
Link: https://lore.kernel.org/r/1573551059-107873-4-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Need to return directly if init hardware failed.
Fixes: 73a4925d15 ("scsi: hisi_sas: Update all the registers after suspend and resume")
Link: https://lore.kernel.org/r/1573551059-107873-3-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.6.0.2
Link: https://lore.kernel.org/r/20191111230401.12958-7-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is setting the initiator nvme template with a max hw queues value of
the present cpu count which is odd. It should be registering the number of
hdwq queues (queues created on the adapter).
Change to set nvme tempate, in all cases, to the number of hardware queues.
Link: https://lore.kernel.org/r/20191111230401.12958-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, cpu_map[cpu#]->hdwq is left to equal LPFC_VECTOR_MAP_EMPTY for
not present CPUs. If a CPU is dynamically hot-added, it is possible we may
crash due to not assigning an allocated hdwq.
Correct by assigning a hdwq at initialization for all not-present CPUs.
Fixes: dcaa213679 ("scsi: lpfc: Change default IRQ model on AMD architectures")
Link: https://lore.kernel.org/r/20191111230401.12958-5-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Compilation can fail due to having an inline function reference where the
function body is not present.
Fix by removing the inline tag.
Fixes: 93a4d6f401 ("scsi: lpfc: Add registration for CPU Offline/Online events")
Link: https://lore.kernel.org/r/20191111230401.12958-4-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity reported the following:
*** CID 101747: Null pointer dereferences (FORWARD_NULL)
/drivers/scsi/lpfc/lpfc_els.c: 4439 in lpfc_cmpl_els_rsp()
4433 kfree(mp);
4434 }
4435 mempool_free(mbox, phba->mbox_mem_pool);
4436 }
4437 out:
4438 if (ndlp && NLP_CHK_NODE_ACT(ndlp)) {
vvv CID 101747: Null pointer dereferences (FORWARD_NULL)
vvv Dereferencing null pointer "shost".
4439 spin_lock_irq(shost->host_lock);
4440 ndlp->nlp_flag &= ~(NLP_ACC_REGLOGIN | NLP_RM_DFLT_RPI);
4441 spin_unlock_irq(shost->host_lock);
4442
4443 /* If the node is not being used by another discovery thread,
4444 * and we are sending a reject, we are done with it.
Fix by adding a check for non-null shost in line 4438.
The scenario when shost is set to null is when ndlp is null.
As such, the ndlp check present was sufficient. But better safe
than sorry so add the shost check.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 101747 ("Null pointer dereferences")
Fixes: 2e0fef85e0 ("[SCSI] lpfc: NPIV: split ports")
CC: James Bottomley <James.Bottomley@SteelEye.com>
CC: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
CC: linux-next@vger.kernel.org
Link: https://lore.kernel.org/r/20191111230401.12958-3-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
TI's J721e SoC has a Cadence UFS IP with a TI specific wrapper. This is a
minimal driver to configure the wrapper. It releases the UFS slave device
out of reset and sets up registers to indicate PHY reference clock input
frequency before probing child Cadence UFS driver.
Link: https://lore.kernel.org/r/20191108164857.11466-3-vigneshr@ti.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid the need to allocate a potentially large array of struct blk_zone
in the block layer by switching the ->report_zones method interface to
a callback model. Now the caller simply supplies a callback that is
executed on each reported zone, and private data for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is no need to arbitrarily limit the size of a report zone to the
number of zones defined by SD_ZBC_REPORT_MAX_ZONES. Rather, simply
calculate the report buffer size needed for the requested number of
zones without exceeding the device total number of zones. This buffer
size limitation to the hardware maximum transfer size and page mapping
capabilities is kept unchanged. Starting with this initial buffer size,
the allocation is optimized by iterating over decreasing buffer size
until the allocation succeeds (each iteration is allowed to fail fast
using the __GFP_NORETRY flag). This ensures forward progress for zone
reports and avoids failures of zones revalidation under memory pressure.
While at it, also replace the hard coded 512 B sector size with the
SECTOR_SIZE macro.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For ZBC and ZAC zoned devices, the scsi driver revalidation processing
implemented by sd_revalidate_disk() includes a call to
sd_zbc_read_zones() which executes a full disk zone report used to
check that all zones of the disk are the same size. This processing is
followed by a call to blk_revalidate_disk_zones(), used to initialize
the device request queue zone bitmaps (zone type and zone write lock
bitmaps). To do so, blk_revalidate_disk_zones() also executes a full
device zone report to obtain zone types. As a result, the entire
zoned block device revalidation process includes two full device zone
report.
By moving the zone size checks into blk_revalidate_disk_zones(), this
process can be optimized to a single full device zone report, leading to
shorter device scan and revalidation times. This patch implements this
optimization, reducing the original full device zone report implemented
in sd_zbc_check_zones() to a single, small, report zones command
execution to obtain the size of the first zone of the device. Checks
whether all zones of the device are the same size as the first zone
size are moved to the generic blk_check_zone() function called from
blk_revalidate_disk_zones().
This optimization also has the following benefits:
1) fewer memory allocations in the scsi layer during disk revalidation
as the potentailly large buffer for zone report execution is not
needed.
2) Implement zone checks in a generic manner, reducing the burden on
device driver which only need to obtain the zone size and check that
this size is a power of 2 number of LBAs. Any new type of zoned
block device will benefit from this.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* for-5.5/drivers-post:
scsi: sd_zbc: add zone open, close, and finish support
scsi: core: Handle drivers which set sg_tablesize to zero
scsi: qla2xxx: fix NPIV tear down process
scsi: sd_zbc: Fix sd_zbc_complete()
scsi: qla2xxx: stop timer in shutdown path
scsi: sd: define variable dif as unsigned int instead of bool
scsi: target: cxgbit: Fix cxgbit_fw4_ack()
scsi: qla2xxx: Fix partial flash write of MBI
scsi: qla2xxx: Initialized mailbox to prevent driver load failure
scsi: lpfc: Honor module parameter lpfc_use_adisc
scsi: ufs-bsg: Wake the device before sending raw upiu commands
scsi: lpfc: Check queue pointer before use
scsi: qla2xxx: fixup incorrect usage of host_byte
struct scsi_cmnd cmd->req.resid_len which is returned and set respectively
by the helper functions scsi_get_resid() and scsi_set_resid() is an
unsigned int. Reflect this fact in the interface of these helper functions.
Also fix compilation errors due to min() and max() type mismatch introduced
by this change in scsi debug code, usb transport code and in the USB ENE
card reader driver.
Link: https://lore.kernel.org/r/20191030090847.25650-1-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following kernel warning:
cpumask_of_node(-1): (unsigned)node >= nr_node_ids(1)
Fixes: dcaa213679 ("scsi: lpfc: Change default IRQ model on AMD architectures")
Link: https://lore.kernel.org/r/20191108225947.1395-1-jsmart2021@gmail.com
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following kernel bug report:
BUG: using smp_processor_id() in preemptible [00000000] code: systemd-udevd/954
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Link: https://lore.kernel.org/r/20191107052158.25788-2-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid an uninitialized value (0) for ha->fc4_type_priority being falsely
interpreted as NVMe priority. Not strictly needed any more after the
previous patch, but makes the fc4_type_priority handling more explicit.
Link: https://lore.kernel.org/r/20191107224839.32417-3-martin.wilck@suse.com
Tested-by: David Bond <dbond@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ha->fc4_type_priority is currently initialized only in
qla81xx_nvram_config(). That makes it default to NVMe for other adapters.
Fix it.
Fixes: 84ed362ac4 ("scsi: qla2xxx: Dual FCP-NVMe target port support")
Link: https://lore.kernel.org/r/20191107224839.32417-2-martin.wilck@suse.com
Tested-by: David Bond <dbond@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the code in qla_init.c is initiator code, remove the SCSI target core
include directive.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Link: https://lore.kernel.org/r/20191106044226.5207-2-bvanassche@acm.org
Reviewed-by: Martin Wilck <mwilck@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
P2P needs to take the alternate plogi route.
Link: https://lore.kernel.org/r/20191105150657.8092-8-hmadhani@marvell.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On heavy loads, a memory leak of the srb_t structure is observed. This
would make the qla2xxx_srbs cache gobble up memory.
Fixes: 219d27d714 ("scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands")
Cc: stable@vger.kernel.org # 5.2
Link: https://lore.kernel.org/r/20191105150657.8092-7-hmadhani@marvell.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code assumes abort will remove the original command from the active
list where scsi_done will not be called. Instead, the eh_abort thread will
do the scsi_done. That is not the case. Instead, we have a double
scsi_done calls triggering use after free.
Abort will tell FW to release the command from FW possesion. The original
command will return to ULP with error in its normal fashion via scsi_done.
eh_abort path would wait for the original command completion before
returning. eh_abort path will not perform the scsi_done call.
Fixes: 219d27d714 ("scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands")
Cc: stable@vger.kernel.org # 5.2
Link: https://lore.kernel.org/r/20191105150657.8092-6-hmadhani@marvell.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when GPSC/GPDB switch command fails, driver just returns without doing a
proper cleanup. This patch fixes this memory leak by calling sp->free() in
the error path.
Link: https://lore.kernel.org/r/20191105150657.8092-4-hmadhani@marvell.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On switch, fabric and mgt command timeout, driver send Abort to tell FW to
return the original command. If abort is timeout, then return both Abort
and original command for cleanup.
Fixes: 219d27d714 ("scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands")
Cc: stable@vger.kernel.org # 5.2
Link: https://lore.kernel.org/r/20191105150657.8092-3-hmadhani@marvell.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code will send PRLI with FC-NVMe bit set for the targets which
support only FCP. This may result into issue with targets which do not
understand NVMe and will go into a strange state. This patch would restart
the login process by going back to PLOGI state. The PLOGI state will force
the target to respond to correct PRLI request.
Fixes: c76ae845ea ("scsi: qla2xxx: Add error handling for PLOGI ELS passthrough")
Cc: stable@vger.kernel.org # 5.4
Link: https://lore.kernel.org/r/20191105150657.8092-2-hmadhani@marvell.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement REQ_OP_ZONE_OPEN, REQ_OP_ZONE_CLOSE and REQ_OP_ZONE_FINISH
support to allow explicit control of zone states.
Contains contributions from Matias Bjorling, Hans Holmberg,
Keith Busch and Damien Le Moal.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ajay Joshi <ajay.joshi@wdc.com>
Signed-off-by: Matias Bjorling <matias.bjorling@wdc.com>
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi:
scsi: core: Handle drivers which set sg_tablesize to zero
scsi: qla2xxx: fix NPIV tear down process
scsi: sd_zbc: Fix sd_zbc_complete()
Nine changes, eight in drivers [ufs, target, lpfc x 2, qla2xxx x 4]
and one core change in sd that fixes an I/O failure on DIF type 3
devices.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXbzO+iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYOpAP9/BCSY
2TAFlli2rVQe+ZNjhHcE4Gj92HNPO7ZgvDQvWgD9F184tjG+1pntYGFutoso7Ak6
QimtBw4AuYg9eDKJDKU=
=bQRX
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi into for-5.5/drivers-post
SCSI fixes on 20191101
Nine changes, eight in drivers [ufs, target, lpfc x 2, qla2xxx x 4]
and one core change in sd that fixes an I/O failure on DIF type 3
devices.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (23 commits)
scsi: qla2xxx: stop timer in shutdown path
scsi: sd: define variable dif as unsigned int instead of bool
scsi: target: cxgbit: Fix cxgbit_fw4_ack()
scsi: qla2xxx: Fix partial flash write of MBI
scsi: qla2xxx: Initialized mailbox to prevent driver load failure
scsi: lpfc: Honor module parameter lpfc_use_adisc
scsi: ufs-bsg: Wake the device before sending raw upiu commands
scsi: lpfc: Check queue pointer before use
scsi: qla2xxx: fixup incorrect usage of host_byte
scsi: lpfc: remove left-over BUILD_NVME defines
scsi: core: try to get module before removing device
scsi: hpsa: add missing hunks in reset-patch
scsi: target: core: Do not overwrite CDB byte 1
scsi: ch: Make it possible to open a ch device multiple times again
scsi: fix kconfig dependency warning related to 53C700_LE_ON_BE
scsi: sni_53c710: fix compilation error
scsi: scsi_dh_alua: handle RTPG sense code correctly during state transitions
scsi: qla2xxx: fix a potential NULL pointer dereference
scsi: MAINTAINERS: Update qla2xxx driver
scsi: zfcp: fix reaction on bit error threshold notification
...
In scsi_mq_setup_tags(), cmd_size is calculated based on zero size for the
scatter-gather list in case the low level driver uses SG_NONE in its host
template.
cmd_size is passed on to the block layer for calculation of the request
size, and we've seen NULL pointer dereference errors from the block layer
in drivers where SG_NONE is used and a mq IO scheduler is active,
apparently as a consequence of this (see commit 68ab2d76e4 ("scsi:
cxlflash: Set sg_tablesize to 1 instead of SG_NONE"), and a recent patch by
Finn Thain converting the three m68k NFR5380 drivers to avoid setting
SG_NONE).
Try to avoid these errors by accounting for at least one sg list entry when
calculating cmd_size, regardless of whether the low level driver set a zero
sg_tablesize.
Tested on 030 m68k with the atari_scsi driver - setting sg_tablesize to
SG_NONE no longer results in a crash when loading this driver.
CC: Finn Thain <fthain@telegraphics.com.au>
Link: https://lore.kernel.org/r/1572922150-4358-1-git-send-email-schmitzmic@gmail.com
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to SBC-2 a TRANSFER LENGTH field of zero means that 256 logical
blocks must be transferred. Make the SCSI tracing code follow SBC-2.
Fixes: bf81623542 ("[SCSI] add scsi trace core functions and put trace points")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Link: https://lore.kernel.org/r/20191105215553.185018-1-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.6.0.1
Link: https://lore.kernel.org/r/20191105005708.7399-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some adapters support the ability to hold multiple adapter dumps on the
adapter flash. Some adapters default to enabling this feature while others
default to single-dump.
Make support uniform by enabling dual dump by default.
Link: https://lore.kernel.org/r/20191105005708.7399-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current driver attempts to allocate an interrupt vector per cpu using
the systems managed IRQ allocator (flag PCI_IRQ_AFFINITY). The system IRQ
allocator will either provide the per-cpu vector, or return fewer
vectors. When fewer vectors, they are evenly spread between the numa nodes
on the system. When run on an AMD architecture, if interrupts occur to a
cpu that is not in the same numa node as the adapter generating the
interrupt, there are extreme costs and overheads in performance. Thus, if
1:1 vector allocation is used, or the "balanced" vectors in the other numa
nodes, performance can be hit significantly.
A much more performant model is to allocate interrupts only on the cpus
that are in the numa node where the adapter resides. I/O completion is
still performed by the cpu where the I/O was generated. Unfortunately,
there is no flag to request the managed IRQ subsystem allocate vectors only
for the CPUs in the numa node as the adapter.
On AMD architecture, revert the irq allocation to the normal style
(non-managed) and then use irq_set_affinity_hint() to set the cpu
affinity and disable user-space rebalancing.
Tie the support into CPU offline/online. If the cpu being offlined owns a
vector, the vector is re-affinitized to one of the other CPUs on the same
numa node. If there are no more CPUs on the numa node, the vector has all
affinity removed and lets the system determine where it's serviced.
Similarly, when the cpu that owned a vector comes online, the vector is
reaffinitized to the cpu.
Link: https://lore.kernel.org/r/20191105005708.7399-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The recent affinitization didn't address cpu offlining/onlining. If an
interrupt vector is shared and the low order cpu owning the vector is
offlined, as interrupts are managed, the vector is taken offline. This
causes the other CPUs sharing the vector will hang as they can't get io
completions.
Correct by registering callbacks with the system for Offline/Online
events. When a cpu is taken offline, its eq, which is tied to an interrupt
vector is found. If the cpu is the "owner" of the vector and if the
eq/vector is shared by other CPUs, the eq is placed into a polled mode.
Additionally, code paths that perform io submission on the "sharing CPUs"
will check the eq state and poll for completion after submission of new io
to a wq that uses the eq.
Similarly, when a cpu comes back online and owns an offlined vector, the eq
is taken out of polled mode and rearmed to start driving interrupts for eq.
Link: https://lore.kernel.org/r/20191105005708.7399-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current message on FAWWN events is rather cryptic.
Expand the message to clarify its meaning.
Link: https://lore.kernel.org/r/20191105005708.7399-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prior to the last FC-NVME-2 draft, SLER and CONF were independent. SLER
now requires CONF to be set.
Revise the NVME PRLI checking to look for both inorder to enable SLER.
Link: https://lore.kernel.org/r/20191105005708.7399-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The recently posted patch had a typo that incorrectly tested the receiving
function.
Fix the typo (change == to !=)
Fixes: 95bfc6d8ad ("scsi: lpfc: Make FW logging dynamically configurable")
Link: https://lore.kernel.org/r/20191105005708.7399-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During heavy RCN activity and log_verbose = 0 we see these messages:
2754 PRLI failure DID:521245 Status:x9/xb2c00, data: x0
0231 RSCN timeout Data: x0 x3
0230 Unexpected timeout, hba link state x5
This is due to delayed RSCN activity.
Correct by avoiding the timeout thus the messages by restarting the
discovery timeout whenever an rscn is received.
Filter PRLI responses such that severity depends on whether expected for
the configuration or not. For example, PRLI errors on a fabric will be
informational (they are expected), but Point-to-Point errors are not
necessarily expected so they are raised to an error level.
Link: https://lore.kernel.org/r/20191105005708.7399-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When reading sysfs nvme_info file while a remote port leaves and comes
back, a NULL pointer is encountered. The issue is due to ndlp list
corruption as the the nvme_info_show does not use the same lock as the rest
of the code.
Correct by removing the rcu_xxx_lock calls and replace by the host_lock and
phba->hbaLock spinlocks that are used by the rest of the driver. Given
we're called from sysfs, we are safe to use _irq rather than _irqsave.
Link: https://lore.kernel.org/r/20191105005708.7399-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver today is reading service parameters from the firmware and then
overwriting the firmware-provided values with values of its own. There are
some switch features that require preliminary FLOGI's that are
switch-specific and done prior to the actual fabric FLOGI for traffic. The
fw will perform those FLOGIs and will revise the service parameters for the
features configured. As the driver later overwrites those values with its
own values, it misconfigures things like BBSCN use by doing so.
Correct by eliminating the driver-overwrite of firmware values. The driver
correctly re-reads the service parameters after each link up to obtain the
latest values from firmware.
Link: https://lore.kernel.org/r/20191105005708.7399-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the driver receives a login that is later then LOGO'd by the remote port
(aka ndlp), the driver, upon the completion of the LOGO ACC transmission,
will logout the node and unregister the rpi that is being used for the
node. As part of the unreg, the node's rpi value is replaced by the
LPFC_RPI_ALLOC_ERROR value. If the port is subsequently offlined, the
offline walks the nodes and ensures they are logged out, which possibly
entails unreg'ing their rpi values. This path does not validate the node's
rpi value, thus doesn't detect that it has been unreg'd already. The
replaced rpi value is then used when accessing the rpi bitmask array which
tracks active rpi values. As the LPFC_RPI_ALLOC_ERROR value is not a valid
index for the bitmask, it may fault the system.
Revise the rpi release code to detect when the rpi value is the replaced
RPI_ALLOC_ERROR value and ignore further release steps.
Link: https://lore.kernel.org/r/20191105005708.7399-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
simply not needed there - neither sg_new_read() nor sg_new_write() need
it.
Link: https://lore.kernel.org/r/20191017193925.25539-8-viro@ZenIV.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just use plain copy_from_user() and get_user(). Note that while a
buf-derived pointer gets stored into ->dxferp, all places that actually use
the resulting value feed it either to import_iovec() or to
import_single_range(), and both will do validation.
Link: https://lore.kernel.org/r/20191017193925.25539-7-viro@ZenIV.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use copy_..._user() instead, both in sg_read() and in sg_read_oxfer(). And
don't open-code memdup_user()...
Link: https://lore.kernel.org/r/20191017193925.25539-6-viro@ZenIV.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
... just use copy_from_user(). We copy only SZ_SG_IO_HDR bytes, so that
would, strictly speaking, loosen the check. However, for call chains via
->write() the caller has actually checked the entire range and SG_IO passes
exactly SZ_SG_IO_HDR for count. So no visible behaviour changes happen if
we check only what we really need for copyin.
Link: https://lore.kernel.org/r/20191017193925.25539-5-viro@ZenIV.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We don't need to allocate a temporary buffer and read the entire structure
in it, only to fetch a single field and free what we'd allocated. Just use
get_user() and be done with it...
Link: https://lore.kernel.org/r/20191017193925.25539-4-viro@ZenIV.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
First of all, __put_user() can fail with access_ok() succeeding. And
access_ok() + __copy_to_user() is spelled copy_to_user()...
__put_user() *can* fail with access_ok() succeeding...
Link: https://lore.kernel.org/r/20191017193925.25539-1-viro@ZenIV.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The memory chunk io_req is released by mempool_free. Accessing
io_req->start_time will result in a use after free bug. The variable
start_time is a backup of the timestamp. So, use start_time here to
avoid use after free.
Link: https://lore.kernel.org/r/1572881182-37664-1-git-send-email-bianpan2016@163.com
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix two issues with commit f5187b7d1a ("scsi: qla2xxx: Optimize NPIV
tear down process"): a missing negation in a wait_event_timeout()
condition, and a missing loop end condition.
Fixes: f5187b7d1a ("scsi: qla2xxx: Optimize NPIV tear down process")
Link: https://lore.kernel.org/r/20191105145550.10268-1-martin.wilck@suse.com
Signed-off-by: Martin Wilck <mwilck@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ILLEGAL REQUEST/INVALID FIELD IN CDB error generated by an attempt to
reset a conventional zone does not apply to the reset write pointer command
with the ALL bit set, that is, to REQ_OP_ZONE_RESET_ALL requests. Fix
sd_zbc_complete() to be quiet only in the case of REQ_OP_ZONE_RESET,
excluding REQ_OP_ZONE_RESET_ALL.
Since REQ_OP_ZONE_RESET is the only request handled by sd_zbc_complete(),
also simplify the code using a simple if statement.
[mkp: applied by hand]
Fixes: d81e9d4943 ("scsi: implement REQ_OP_ZONE_RESET_ALL")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191027140549.26272-4-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nine changes, eight in drivers [ufs, target, lpfc x 2, qla2xxx x 4]
and one core change in sd that fixes an I/O failure on DIF type 3
devices.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXbzO+iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYOpAP9/BCSY
2TAFlli2rVQe+ZNjhHcE4Gj92HNPO7ZgvDQvWgD9F184tjG+1pntYGFutoso7Ak6
QimtBw4AuYg9eDKJDKU=
=bQRX
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine changes, eight in drivers [ufs, target, lpfc x 2, qla2xxx x 4]
and one core change in sd that fixes an I/O failure on DIF type 3
devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: stop timer in shutdown path
scsi: sd: define variable dif as unsigned int instead of bool
scsi: target: cxgbit: Fix cxgbit_fw4_ack()
scsi: qla2xxx: Fix partial flash write of MBI
scsi: qla2xxx: Initialized mailbox to prevent driver load failure
scsi: lpfc: Honor module parameter lpfc_use_adisc
scsi: ufs-bsg: Wake the device before sending raw upiu commands
scsi: lpfc: Check queue pointer before use
scsi: qla2xxx: fixup incorrect usage of host_byte
This patch fixes an unintended sign extension on left shifts. From Colin
King: "Shifting a u8 left will cause the value to be promoted to an
integer. If the top bit of the u8 is set then the following conversion to
an u64 will sign extend the value causing the upper 32 bits to be set in
the result."
Fix this by using get_unaligned_be*() instead.
Fixes: bf81623542 ("[SCSI] add scsi trace core functions and put trace points")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Link: https://lore.kernel.org/r/20191101211447.187151-1-bvanassche@acm.org
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Only csio_hw_free() calling csio_dfs_destroy() and it is not checking
return value. So remove the return from csio_dfs_destroy().
Link: https://lore.kernel.org/r/20191028194234.GA27848@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
debugfs_remove_recursive() has taken the null pointer into account. Remove
the null check before debugfs_remove_recursive().
Link: https://lore.kernel.org/r/20191026195625.GA22455@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace assignment of 0 to pointer with NULL assignment.
Link: https://lore.kernel.org/r/20191025135010.GA6191@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It isn't necessary to check the host depth in scsi_queue_rq() any more
since it has been respected by blk-mq before calling scsi_queue_rq() via
getting driver tag.
Lots of LUNs may attach to same host and per-host IOPS may reach millions,
so we should avoid expensive atomic operations on the host-wide counter in
the IO path.
This patch implements scsi_host_busy() via blk_mq_tagset_busy_iter() with
one scsi command state for reading the count of busy IOs for scsi_mq.
It is observed that IOPS is increased by 15% in IO test on scsi_debug (32
LUNs, 32 submit queues, 1024 can_queue, libaio/dio) in a dual-socket
system.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Omar Sandoval <osandov@fb.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20191025065855.6309-1-ming.lei@redhat.com
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Declare all variables that hold dev_cmd_type values as an enum instead of
as an int.
Cc: Yaniv Gardi <ygardi@codeaurora.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191029230710.211926-3-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following three kernel-doc warnings:
drivers/scsi/ufs/ufs_bsg.c:165: warning: Function parameter or member 'hba' not described in 'ufs_bsg_remove'
drivers/scsi/ufs/ufshcd.c:5789: warning: Function parameter or member 'cmd_type' not described in 'ufshcd_issue_devman_upiu_cmd'
drivers/scsi/ufs/ufshcd.c:5789: warning: Excess function parameter 'msgcode' description in 'ufshcd_issue_devman_upiu_cmd'
Cc: Yaniv Gardi <ygardi@codeaurora.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191029230710.211926-2-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no need to call ufshcd_def_desc_sizes() in ufshcd_init(), since
descriptor lengths will be checked and initialized later in
ufshcd_init_desc_sizes().
Fixes: a4b0e8a4e92b1b(scsi: ufs: Factor out ufshcd_read_desc_param)
Link: https://lore.kernel.org/r/BN7PR08MB5684A3ACE214C3D4792CE729DB610@BN7PR08MB5684.namprd08.prod.outlook.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Avri Altman <avri.altman.wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull RCU and LKMM changes from Paul E. McKenney:
- Documentation updates.
- Miscellaneous fixes.
- Dynamic tick (nohz) updates, perhaps most notably changes to
force the tick on when needed due to lengthy in-kernel execution
on CPUs on which RCU is waiting.
- Replace rcu_swap_protected() with rcu_prepace_pointer().
- Torture-test updates.
- Linux-kernel memory consistency model updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This commit replaces the use of rcu_swap_protected() with the more
intuitively appealing rcu_replace_pointer() as a step towards removing
rcu_swap_protected().
Link: https://lore.kernel.org/lkml/CAHk-=wiAsJLw1egFEE=Z7-GGtM6wcvtyytXZA1+BHqta4gg6Hw@mail.gmail.com/
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
[ paulmck: From rcu_replace() to rcu_replace_pointer() per Ingo Molnar. ]
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Fix sparse warning:
drivers/scsi/lpfc/lpfc_debugfs.c:2083:1: warning:
symbol 'lpfc_debugfs_ras_log_data' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20191028132556.16272-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In shutdown/reboot paths, the timer is not stopped:
qla2x00_shutdown
pci_device_shutdown
device_shutdown
kernel_restart_prepare
kernel_restart
sys_reboot
This causes lockups (on powerpc) when firmware config space access calls
are interrupted by smp_send_stop later in reboot.
Fixes: e30d175648 ("[SCSI] qla2xxx: Addition of shutdown callback handler.")
Link: https://lore.kernel.org/r/20191024063804.14538-1-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
mempool_destroy has taken null pointer check into account. Remove the
redundant check.
Link: https://lore.kernel.org/r/20191026194712.GA22249@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
convert MAGIC_NUMER_xxx to MAGIC_NUMBER_xxx
Link: https://lore.kernel.org/r/20191025184342.6623-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_debufs.c was missing include of vmalloc.h when compiled on PPC.
Add missing header.
Link: https://lore.kernel.org/r/20191025182530.26653-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nine changes, eight to drivers (qla2xxx, hpsa, lpfc, alua, ch,
53c710[x2], target) and one core change that tries to close a race
between sysfs delete and module removal.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXbN1gSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWUzAP4tB9Z+
X5zfnMLmeAtSCnVwIgFX3/GVSFfzEmi+3VxfBQEA3nfs5AAJCPsaTk9z+jLtAKPk
6uYoHwsyTHal19Ojt9g=
=IOPn
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine changes, eight to drivers (qla2xxx, hpsa, lpfc, alua, ch,
53c710[x2], target) and one core change that tries to close a race
between sysfs delete and module removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: remove left-over BUILD_NVME defines
scsi: core: try to get module before removing device
scsi: hpsa: add missing hunks in reset-patch
scsi: target: core: Do not overwrite CDB byte 1
scsi: ch: Make it possible to open a ch device multiple times again
scsi: fix kconfig dependency warning related to 53C700_LE_ON_BE
scsi: sni_53c710: fix compilation error
scsi: scsi_dh_alua: handle RTPG sense code correctly during state transitions
scsi: qla2xxx: fix a potential NULL pointer dereference
The number of phy down reflects the quality of the link between SAS
controller and disk. In order to allow the user to confirm the link quality
of the system, we record the number of phy down for each phy.
The user can check the current phy down count by reading the debugfs file
corresponding to the specific phy, or clear the phy down count by writing 0
to the debugfs file.
Link: https://lore.kernel.org/r/1571926105-74636-19-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Although if the debugfs initialization fails, we will delete the debugfs
folder of hisi_sas, but we did not consider the scenario where debugfs was
successfully initialized, but the probe failed for other reasons. We found
out that hisi_sas folder is still remain after the probe failed.
When probe fail, we should delete debugfs folder to avoid the above issue.
Link: https://lore.kernel.org/r/1571926105-74636-18-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We use the module parameter debugfs_dump_count to manage the upper limit of
the memory block for multiple dumps.
Link: https://lore.kernel.org/r/1571926105-74636-17-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We add multiple dumps for debugfs, but only allocate memory this time and
only dump #0.
Link: https://lore.kernel.org/r/1571926105-74636-15-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address for
ITCT cache at debugfs. This structure is bound to the corresponding debugfs
file, it can help callback function of debugfs file to get what it needs.
Link: https://lore.kernel.org/r/1571926105-74636-14-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address for IOST
cache at debugfs. This structure is bound to the corresponding debugfs
file, it can help callback function of debugfs file to get what it needs.
Link: https://lore.kernel.org/r/1571926105-74636-13-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address for ITCT
at debugfs. This structure is bound to the corresponding debugfs file, it
can help callback function of debugfs file to get what it needs.
Link: https://lore.kernel.org/r/1571926105-74636-12-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address for IOST
at debugfs. This structure is bound to the corresponding debugfs file, it
can help callback function of debugfs file to get what it needs.
Link: https://lore.kernel.org/r/1571926105-74636-11-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address and phy
pointer for port at debugfs. This structure is bound to the corresponding
debugfs file, it can help callback function of debugfs file to get what it
need.
Link: https://lore.kernel.org/r/1571926105-74636-10-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address and
hisi_hba pointer for REGS at debugfs. This structure is bound to the
corresponding debugfs file, it can help callback function of debugfs file
to get what it need.
Link: https://lore.kernel.org/r/1571926105-74636-9-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address and DQ
pointer for DQ at debugfs. This structure is bound to the corresponding
debugfs file, it can help callback function of debugfs file to get what it
need.
Link: https://lore.kernel.org/r/1571926105-74636-8-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a file structure which was used to save the memory address and CQ
pointer for CQ at debugfs. This structure is bound to the corresponding
debugfs file, it can help callback function of debugfs file to get what it
need.
Link: https://lore.kernel.org/r/1571926105-74636-7-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's useful to know when the dump occurred, so add a timestamp file for
this.
Link: https://lore.kernel.org/r/1571926105-74636-6-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For IOs from upper layer, preemption may be disabled as it may be called by
function __blk_mq_delay_run_hw_queue which will call get_cpu() (it disables
preemption). So if flags HISI_SAS_REJECT_CMD_BIT is set in function
hisi_sas_task_exec(), it may disable preempt twice after down() and up()
which will cause following call trace:
BUG: scheduling while atomic: fio/60373/0x00000002
Call trace:
dump_backtrace+0x0/0x150
show_stack+0x24/0x30
dump_stack+0xa0/0xc4
__schedule_bug+0x68/0x88
__schedule+0x4b8/0x548
schedule+0x40/0xd0
schedule_timeout+0x200/0x378
__down+0x78/0xc8
down+0x54/0x70
hisi_sas_task_exec.isra.10+0x598/0x8d8 [hisi_sas_main]
hisi_sas_queue_command+0x28/0x38 [hisi_sas_main]
sas_queuecommand+0x168/0x1b0 [libsas]
scsi_queue_rq+0x2ac/0x980
blk_mq_dispatch_rq_list+0xb0/0x550
blk_mq_do_dispatch_sched+0x6c/0x110
blk_mq_sched_dispatch_requests+0x114/0x1d8
__blk_mq_run_hw_queue+0xb8/0x130
__blk_mq_delay_run_hw_queue+0x1c0/0x220
blk_mq_run_hw_queue+0xb0/0x128
blk_mq_sched_insert_requests+0xdc/0x208
blk_mq_flush_plug_list+0x1b4/0x3a0
blk_flush_plug_list+0xdc/0x110
blk_finish_plug+0x3c/0x50
blkdev_direct_IO+0x404/0x550
generic_file_read_iter+0x9c/0x848
blkdev_read_iter+0x50/0x78
aio_read+0xc8/0x170
io_submit_one+0x1fc/0x8d8
__arm64_sys_io_submit+0xdc/0x280
el0_svc_common.constprop.0+0xe0/0x1e0
el0_svc_handler+0x34/0x90
el0_svc+0x10/0x14
...
To solve the issue, check preemptible() to avoid disabling preempt multiple
when flag HISI_SAS_REJECT_CMD_BIT is set.
Link: https://lore.kernel.org/r/1571926105-74636-5-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When injecting 2bit ecc errors, it will cause confusion inside SAS
controller which needs host reset to recover it. If a device is gone at the
same times inject 2bit ecc errors, we may not receive the ITCT interrupt so
it will wait for completion in clear_itct_v3_hw() all the time. And host
reset will also not occur because it can't require hisi_hba->sem, so the
system will be suspended.
To solve the issue, use wait_for_completion_timeout() instead of
wait_for_completion(), and also don't mark the gone device as
SAS_PHY_UNUSED when device gone.
Link: https://lore.kernel.org/r/1571926105-74636-4-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If set the BIST init value after enabling BIST, there may be still some few
error bits. According to the process, need to set the BIST init value
before enabling BIST.
Fixes: 97b151e758 ("scsi: hisi_sas: Add BIST support for phy loopback")
Link: https://lore.kernel.org/r/1571926105-74636-3-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to a merge error, we attempt to create 2x debugfs dump folders, which
fails:
[ 861.101914] debugfs: Directory 'dump' with parent '0000:74:02.0'
already present!
This breaks the dump function.
To fix, remove the superfluous attempt to create the folder.
Fixes: 7ec7082c57 ("scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation")
Link: https://lore.kernel.org/r/1571926105-74636-2-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix misspellings of "disonnect", "reconnect", "connection", "connected",
and "disconnection".
Link: https://lore.kernel.org/r/20191024152633.30404-1-geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From an interrupt handler path memory may be allocated using
GFP_KERNEL, replace it with GFP_ATOMIC.
_base_interrupt->_scsih_io_done->_scsih_smart_predicted_fault
Link: https://lore.kernel.org/r/20191024152835.6177-1-thenzl@redhat.com
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This error path is missing an unlock.
Fixes: 26780d9e12 ("[SCSI] esas2r: ATTO Technology ExpressSAS 6G SAS/SATA RAID Adapter Driver")
Link: https://lore.kernel.org/r/20191022102324.GA27540@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:2076:15:
warning: variable ppmax set but not used [-Wunused-but-set-variable]
drivers/target/iscsi/cxgbit/cxgbit_ddp.c:300:15:
warning: variable ppmax set but not used [-Wunused-but-set-variable]
It is not used since commit a248384e64 ("cxgb4/libcxgb/cxgb4i/cxgbit:
enable eDRAM page pods for iSCSI")
Link: https://lore.kernel.org/r/20191021142042.30964-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These are called with IRQs disabled from csio_mgmt_tmo_handler() so we
can't call spin_unlock_irq() or it will enable IRQs prematurely.
Fixes: a3667aaed5 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Link: https://lore.kernel.org/r/20191019085913.GA14245@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace assignment of 0 to pointer with NULL assignment.
Link: https://lore.kernel.org/r/20191024030857.GA12097@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace assignment of 0 to pointer with NULL assignment.
Link: https://lore.kernel.org/r/20191024025726.GA31421@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.6.0.0
Link: https://lore.kernel.org/r/20191018211832.7917-17-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When debugging a recent discovery customer problem it was very hard to tell
what was happening with the existing discovery log messages. To fully debug
the issue additional log messages were necessary.
Add or extend log messages so that sufficient information is present for
debugging.
Link: https://lore.kernel.org/r/20191018211832.7917-16-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the past, the lpe32000 models, based their main support being for 32G,
and as FC-AL is not supported in the FC standards past 8G, did not support
FC-AL operation.
This patch adds private-loop FC-AL support for the LPE32000 adapters
when a link is 8G or below. To avoid conditions where link rate may
change, which would cause non-connectivity to the AL device, FC-AL
mode must become a persistent setting and the link kept at a speed
supporting FC-AL.
The patch:
- Adds a pls attribute indicating whether the adapter properly supports
FC-AL.
- Adds support for the adapter to indicate that topology should be fixed
and the topology types to be configured.
- Adds a pt attribute to report the persistent topology if present.
Link: https://lore.kernel.org/r/20191018211832.7917-15-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add decode support for adapter Async Events which report FA-WWN
configuration errors.
Link: https://lore.kernel.org/r/20191018211832.7917-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add two new macros to aid in message logging:
Both macros print a message if the corresponding lpfc verbosity setting is
set or the kernel log level is WARNING or more critical.
One macro is for use with a phba structure, the other with a vport
structure.
[mkp: typo]
Link: https://lore.kernel.org/r/20191018211832.7917-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the FW logging facility is a load/boot time parameter which
requires the driver to be unloaded/reloaded or the system rebooted in order
to change its configuration.
Convert the logging facility to allow dynamic enablement and configuration.
Specifically:
- Convert the feature so that it can be enabled dynamically via an
attribute. Additionally, the size of the buffer can be configured
dynamically.
- Add locks around states that now may be changing.
- Tie the feature into debugfs so that the logs can be read at any time.
Link: https://lore.kernel.org/r/20191018211832.7917-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The existing "auto eq delay" mechanism was sometimes skipping over an EQ,
not ramping the coalescing down under light load fast enough, and in other
cases never kicked in as cpu sharing by multiple vectors didn't quite add
up right.
Tweak the interrupt mechanism such that:
- Add a flag to the EQ to force checking for colaescing values when being
serviced in the interrupt handler. The flag will be set by any CQ bound
to the EQ whenever the number of CQ elements process in a single scan
meets or exceeds the hardware queue notify level. E.g. there's a
significant number of completions happening.
- In the heartbeat work item that checks coalescing:
- Replace the structure that was counting the number of EQs that
interrupted on a single cpu with a new structure that looks at the EQ
to see whether EQ currently has a coalescing value (thus it should be
re-evaluate) or was marked by the new flag indicating heavy
completions.
- When a cpu, which may be servicing multiple vectors, had at least 1 EQ
that should be checked, a new coalescing delay is calculated based on
the number of interrupts that occurred on the cpu.
- The new coalescing value is then applied to the EQs that had
interrupted on the cpu.
Link: https://lore.kernel.org/r/20191018211832.7917-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lower IOps performance with write operations. Perf tool shows lock
contention in dma_pool_alloc and dma_pool_free related to the
txrdy_payload_pool.
The allocations are for dma buffers for XFER_RDY's, which actually are not
needed for the FCP_TRECEIVE command as the command contents are used by the
adapter to generate the IU.
Remove the allocations and the associated buffer pool. Rather than leaving
NULLs in buffer pointer locations, set command and sgl to indicate skipped
SGLE indexes.
Link: https://lore.kernel.org/r/20191018211832.7917-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Slightly rework some error check code paths for better streamlining.
Added compiler unlikely hints to allow slightly better optimization of the
fast-path.
Removed a few pointer checks that were obviously already valid.
Link: https://lore.kernel.org/r/20191018211832.7917-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Log message conditional upon vport being NULL dereferences vport to
determine log verbose setting.
Changed to use lpfc_print_log which uses phba to determine the active log
verbose setting.
Fixes: 43bfea1bff ("scsi: lpfc: Fix coverity errors on NULL pointer checks")
Link: https://lore.kernel.org/r/20191018211832.7917-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In lpfc_abort_handler, the lock acquire order is hbalock (irqsave),
buf_lock (irq) and ring_lock (irq). The issue is that in two places the
locks are released out of order - the buf_lock and the hbalock - resulting
in the cpu preemption/lock flags getting restored out of order and
deadlocking the cpu.
Fix the unlock order by fully releasing the hbalocks as well.
CC: Zhangguanghui <zhang.guanghui@h3c.com>
Link: https://lore.kernel.org/r/20191018211832.7917-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In cases where I/O may be aborted, such as driver unload or link bounces,
the system will crash based on a bad ndlp pointer.
Example:
RIP: 0010:lpfc_sli4_abts_err_handler+0x15/0x140 [lpfc]
...
lpfc_sli4_io_xri_aborted+0x20d/0x270 [lpfc]
lpfc_sli4_sp_handle_abort_xri_wcqe.isra.54+0x84/0x170 [lpfc]
lpfc_sli4_fp_handle_cqe+0xc2/0x480 [lpfc]
__lpfc_sli4_process_cq+0xc6/0x230 [lpfc]
__lpfc_sli4_hba_process_cq+0x29/0xc0 [lpfc]
process_one_work+0x14c/0x390
Crash was caused by a bad ndlp address passed to I/O indicated by the XRI
aborted CQE. The address was not NULL so the routine deferenced the ndlp
ptr. The bad ndlp also caused the lpfc_sli4_io_xri_aborted to call an
erroneous io handler. Root cause for the bad ndlp was an lpfc_ncmd that
was aborted, put on the abort_io list, completed, taken off the abort_io
list, sent to lpfc_release_nvme_buf where it was put back on the abort_io
list because the lpfc_ncmd->flags setting LPFC_SBUF_XBUSY was not cleared
on the final completion.
Rework the exchange busy handling to ensure the flags are properly set for
both scsi and nvme.
Fixes: c490850a09 ("scsi: lpfc: Adapt partitioned XRI lists to efficient sharing")
Cc: <stable@vger.kernel.org> # v5.1+
Link: https://lore.kernel.org/r/20191018211832.7917-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When operating in private loop mode, PLOGI exchanges are racing and the
driver tries to abort it's PLOGI. But the PLOGI abort ends up terminating
the login with the other end causing the other end to abort its PLOGI as
well. Discovery never fully completes.
Fix by disabling the PLOGI abort when private loop and letting the state
machine play out.
Link: https://lore.kernel.org/r/20191018211832.7917-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix lockdep error in __lpfc_sli_ringtx_put(): The hbalock is valid for
sli3, but not for sli4. Change lockdep to look at ring lock if sli4.
Also update comment in __lpfc_sli_issue_iocb_s4() to reflect proper
lock. Note: lockdep check is already correct.
Link: https://lore.kernel.org/r/20191018211832.7917-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the adapter FW is administratively set to RO mode, a FW update
triggered by the driver's sysfs attribute will fail. Currently, the
driver's logging mechanism does not properly parse the adapter return codes
and print a meaningful message. This oversight prevents quick diagnosis in
the field.
Parse the adapter return codes for Write_Object and write an appropriate
message to the system console.
[mkp: typo]
Link: https://lore.kernel.org/r/20191018211832.7917-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, lpfc_nvmet_mrq is always scaled back to the min(lpfc_nvmet_mrq,
lpfc_irq_chann). There's no reason to reduce it to the number of interrupt
vectors. Rather, it should be scaled down based on the number of hardware
queues for the system (if lower than max of 16).
Change scaling to use hardware queue count rather than interrupt vector
count.
Link: https://lore.kernel.org/r/20191018211832.7917-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable dif in function sd_setup_read_write_cmnd() is the return value of
function scsi_host_dif_capable() which returns dif capability of disks. If
define it as bool, even for the disks which support DIF3, the function
still return dif=1, which causes IO error. So define variable dif as
unsigned int instead of bool.
Fixes: e249e42d27 ("scsi: sd: Clean up sd_setup_read_write_cmnd()")
Link: https://lore.kernel.org/r/1571725628-132736-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sed_ioctl() function is written to be compatible between
32-bit and 64-bit processes, however compat mode is only
wired up for nvme, not for sd.
Add the missing call to sed_ioctl() in sd_compat_ioctl().
Fixes: d80210f25f ("sd: add support for TCG OPAL self encrypting disks")
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SG_GET_REQUEST_TABLE is now the last ioctl command that needs a conversion
handler. This is only used in a single file, so the implementation should
be there.
I'm trying to simplify it in the process, to get rid of
the compat_alloc_user_space() and extra copy, by adding a
put_compat_request_table() function instead, which copies the data in
the right format to user space.
Cc: linux-scsi@vger.kernel.org
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are two code locations that implement the SG_IO ioctl: the old
sg.c driver, and the generic scsi_ioctl helper that is in turn used by
multiple drivers.
To eradicate the old compat_ioctl conversion handler for the SG_IO
command, I implement a readable pair of put_sg_io_hdr() /get_sg_io_hdr()
helper functions that can be used for both compat and native mode,
and then I call this from both drivers.
For the iovec handling, there is already a compat_import_iovec() function
that can simply be called in place of import_iovec().
To avoid having to pass the compat/native state through multiple
indirections, I mark the SG_IO command itself as compatible in
fs/compat_ioctl.c and use in_compat_syscall() to figure out where
we are called from.
As a side-effect of this, the sg.c driver now also accepts the 32-bit
sg_io_hdr format in compat mode using the read/write interface, not
just ioctl. This should improve compatiblity with old 32-bit binaries,
but it would break if any application intentionally passes the 64-bit
data structure in compat mode here.
Steffen Maier helped debug an issue in an earlier version of this patch.
Cc: Steffen Maier <maier@linux.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
MTIOCPOS and MTIOCGET are incompatible between 32-bit and 64-bit user
space, and traditionally have been translated in fs/compat_ioctl.c.
To get rid of that translation handler, move a corresponding
implementation into each of the four drivers implementing those commands.
The interesting part of that is now in a new linux/mtio.h header that
wraps the existing uapi/linux/mtio.h header and provides an abstraction
to let drivers handle both cases easily. Using an in_compat_syscall()
check, the caller does not have to keep track of whether this was
called through .unlocked_ioctl() or .compat_ioctl().
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "Kai Mäkisara" <Kai.Makisara@kolumbus.fi>
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A handful of drivers all have a trivial wrapper around their ioctl
handler, but don't call the compat_ptr() conversion function at the
moment. In practice this does not matter, since none of them are used
on the s390 architecture and for all other architectures, compat_ptr()
does not do anything, but using the new compat_ptr_ioctl()
helper makes it more correct in theory, and simplifies the code.
I checked that all ioctl handlers in these files are compatible
and take either pointer arguments or no argument.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The .ioctl and .compat_ioctl file operations have the same prototype so
they can both point to the same function, which works great almost all
the time when all the commands are compatible.
One exception is the s390 architecture, where a compat pointer is only
31 bit wide, and converting it into a 64-bit pointer requires calling
compat_ptr(). Most drivers here will never run in s390, but since we now
have a generic helper for it, it's easy enough to use it consistently.
I double-checked all these drivers to ensure that all ioctl arguments
are used as pointers or are ignored, but are not interpreted as integer
values.
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/cxlflash/main.c:47:22: warning:
variable ioarcb set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Link: https://lore.kernel.org/r/20191021141957.18828-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Matthew R. Ochs <mrochs@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For new adapters with multiple flash regions to write to, current code
allows FW & Boot regions to be written, while other regions are blocked via
sysfs. The fix is to block all flash read/write through sysfs interface.
Fixes: e81d1bcbde ("scsi: qla2xxx: Further limit FLASH region write access from SysFS")
Cc: stable@vger.kernel.org # 5.2
Link: https://lore.kernel.org/r/20191022193643.7076-3-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Girish Basrur <gbasrur@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue with Gen7 adapter in a blade environment where one
of the ports will not be detected by driver. Firmware expects mailbox 11 to
be set or cleared by driver for newer ISP.
Following message is seen in the log file:
[ 18.810892] qla2xxx [0000:d8:00.0]-1820:1: **** Failed=102 mb[0]=4005 mb[1]=37 mb[2]=20 mb[3]=8
[ 18.819596] cmd=2 ****
[mkp: typos]
Link: https://lore.kernel.org/r/20191022193643.7076-2-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The initial lpfc_desc_set_adisc implementation in commit
dea3101e0a ("lpfc: add Emulex FC driver version 8.0.28") enabled ADISC if
cfg_use_adisc && RSCN_MODE && FCP_2_DEVICE
In commit 92d7f7b0cd ("[SCSI] lpfc: NPIV: add NPIV support on top of
SLI-3") this changed to
(cfg_use_adisc && RSC_MODE) || FCP_2_DEVICE
and later in commit ffc954936b ("[SCSI] lpfc 8.3.13: FC Discovery Fixes
and enhancements.") to
(cfg_use_adisc && RSC_MODE) || (FCP_2_DEVICE && FCP_TARGET)
A customer reports that after a devloss, an ADISC failure is logged. It
turns out the ADISC flag is set even the user explicitly set lpfc_use_adisc
= 0.
[Sat Dec 22 22:55:58 2018] lpfc 0000:82:00.0: 2:(0):0203 Devloss timeout on WWPN 50:01:43:80:12:8e:40:20 NPort x05df00 Data: x82000000 x8 xa
[Sat Dec 22 23:08:20 2018] lpfc 0000:82:00.0: 2:(0):2755 ADISC failure DID:05DF00 Status:x9/x70000
[mkp: fixed Hannes' email]
Fixes: 92d7f7b0cd ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3")
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: James Smart <james.smart@broadcom.com>
Link: https://lore.kernel.org/r/20191022072112.132268-1-dwagner@suse.de
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After IOP reset completion, AIF request command is not issued to the
controller. Driver schedules a worker thread to issue a AIF request command
after IOP reset completion.
[mkp: fix zeroday warning]
Link: https://lore.kernel.org/r/1571120524-6037-7-git-send-email-balsundar.p@microsemi.com
Acked-by: Balsundar P < Balsundar.P@microchip.com>
Signed-off-by: Balsundar P <balsundar.p@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently driver waits for the command IOCTL from the firmware and if the
firmware enters nonresponsive state, the driver doesn't respond till the
firmware is responsive again.
Check that firmware is alive, otherwise return -EBUSY.
[mkp: clarified commit desc]
Link: https://lore.kernel.org/r/1571120524-6037-6-git-send-email-balsundar.p@microsemi.com
Signed-off-by: Balsundar P <balsundar.p@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before issuing IOP reset, INTX mode is selected. This is triggering MSGU
lockup and ended in basecode assert. Use DROP_IO command when IOP reset is
sent in preparation for interrupt mode switch.
Link: https://lore.kernel.org/r/1571120524-6037-4-git-send-email-balsundar.p@microsemi.com
Signed-off-by: Balsundar P <balsundar.p@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The problem is the driver detects FastResponse bit set and saves it to
Fib's flags to not check IO response status, but it never clears it for
next IO. Hence the next IO will pick up FastResponse bit to not check
the IO response status and fail to report any type IO error to kernel
Link: https://lore.kernel.org/r/1571120524-6037-3-git-send-email-balsundar.p@microsemi.com
Signed-off-by: Balsundar P <balsundar.p@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The scsi async probe process is calling blk_pm_runtime_init for each lun,
and then those request queues are monitored by the block layer pm
engine (blk-pm.c). This is however, not the case for scsi-passthrough
queues, created by bsg_setup_queue().
So the ufs-bsg driver might send various commands, disregarding the pm
status of the device. This is wrong, regardless if its request queue is
pm-aware or not.
Fixes: df032bf27a (scsi: ufs: Add a bsg endpoint that supports UPIUs)
Link: https://lore.kernel.org/r/1570696267-8487-1-git-send-email-avri.altman@wdc.com
Reported-by: Yuliy Izrailov <yuliy.izrailov@wdc.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The queue pointer might not be valid. The rest of the code checks the
pointer before accessing it. lpfc_sli4_process_missed_mbox_completions is
the only place where the check is missing.
Fixes: 657add4e5e ("scsi: lpfc: Fix poor use of hardware queues if fewer irq vectors")
Cc: James Smart <jsmart2021@gmail.com>
Link: https://lore.kernel.org/r/20191018162111.8798-1-dwagner@suse.de
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
DRIVER_ERROR is a a driver byte setting, not a host byte. The qla2xxx
driver should rather return DID_ERROR here to be in line with the other
drivers.
Link: https://lore.kernel.org/r/20191018140458.108278-1-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----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=LmPS
-----END PGP SIGNATURE-----
Merge tag 'mkp-scsi-postmerge' of git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi
Pull scsi fixes from Martin Petersen:
"These two commits were in a separate postmerge branch due to a
dependency on changes merged for 5.4 in the block tree.
They fix two issues in the intersection of the request cleanup changes
from block (b7e9e1fb7a) and the request batching changes
(8930a6c207) that were made to SCSI during the 5.4 cycle"
* tag 'mkp-scsi-postmerge' of git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi:
scsi: core: fix dh and multipathing for SCSI hosts without request batching
scsi: core: fix missing .cleanup_rq for SCSI hosts without request batching
As said in commit f2c2cbcc35 ("powerpc: Use pr_warn instead of
pr_warning"), removing pr_warning so all logging messages use a
consistent <prefix>_warn style. Let's do it.
Link: http://lkml.kernel.org/r/20191018031850.48498-21-wangkefeng.wang@huawei.com
To: linux-kernel@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
The BUILD_NVME define never got defined anywhere, causing NVMe commands to
be treated as SCSI commands when freeing the buffers. This was causing a
stuck discovery and a horrible crash in lpfc_set_rrq_active() later on.
Link: https://lore.kernel.org/r/20191017150019.75769-1-hare@suse.de
Fixes: c00f62e6c5 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have a test case like block/001 in blktests, which will create a scsi
device by loading scsi_debug module and then try to delete the device by
sysfs interface. At the same time, it may remove the scsi_debug module.
And getting a invalid paging request BUG_ON as following:
[ 34.625854] BUG: unable to handle page fault for address: ffffffffa0016bb8
[ 34.629189] Oops: 0000 [#1] SMP PTI
[ 34.629618] CPU: 1 PID: 450 Comm: bash Tainted: G W 5.4.0-rc3+ #473
[ 34.632524] RIP: 0010:scsi_proc_hostdir_rm+0x5/0xa0
[ 34.643555] CR2: ffffffffa0016bb8 CR3: 000000012cd88000 CR4: 00000000000006e0
[ 34.644545] Call Trace:
[ 34.644907] scsi_host_dev_release+0x6b/0x1f0
[ 34.645511] device_release+0x74/0x110
[ 34.646046] kobject_put+0x116/0x390
[ 34.646559] put_device+0x17/0x30
[ 34.647041] scsi_target_dev_release+0x2b/0x40
[ 34.647652] device_release+0x74/0x110
[ 34.648186] kobject_put+0x116/0x390
[ 34.648691] put_device+0x17/0x30
[ 34.649157] scsi_device_dev_release_usercontext+0x2e8/0x360
[ 34.649953] execute_in_process_context+0x29/0x80
[ 34.650603] scsi_device_dev_release+0x20/0x30
[ 34.651221] device_release+0x74/0x110
[ 34.651732] kobject_put+0x116/0x390
[ 34.652230] sysfs_unbreak_active_protection+0x3f/0x50
[ 34.652935] sdev_store_delete.cold.4+0x71/0x8f
[ 34.653579] dev_attr_store+0x1b/0x40
[ 34.654103] sysfs_kf_write+0x3d/0x60
[ 34.654603] kernfs_fop_write+0x174/0x250
[ 34.655165] __vfs_write+0x1f/0x60
[ 34.655639] vfs_write+0xc7/0x280
[ 34.656117] ksys_write+0x6d/0x140
[ 34.656591] __x64_sys_write+0x1e/0x30
[ 34.657114] do_syscall_64+0xb1/0x400
[ 34.657627] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 34.658335] RIP: 0033:0x7f156f337130
During deleting scsi target, the scsi_debug module have been removed. Then,
sdebug_driver_template belonged to the module cannot be accessd, resulting
in scsi_proc_hostdir_rm() BUG_ON.
To fix the bug, we add scsi_device_get() in sdev_store_delete() to try to
increase refcount of module, avoiding the module been removed.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191015130556.18061-1-yuyufen@huawei.com
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct returning from reset before outstanding commands are completed
for the device.
Link: https://lore.kernel.org/r/157107623870.17997.11208813089704833029.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Five changes, two in drivers (qla2xxx, zfcp), one to MAINTAINERS
(qla2xxx) and two in the core. The last two are mostly about removing
incorrect messages from the kernel log: the resid message is
definitely wrong and the sync cache on protected drive problem is
arguably wrong.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXaYZYCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVuDAP9HBhGv
dQ3FPA7gZ33rmsb8M1Q1NJ0GJuvFj2muh9CFYwD6AoJtVLivVZR75gojLLMqKpuf
6EwRTaUZwYAoWeILNuA=
=+iTy
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five changes, two in drivers (qla2xxx, zfcp), one to MAINTAINERS
(qla2xxx) and two in the core.
The last two are mostly about removing incorrect messages from the
kernel log: the resid message is definitely wrong and the sync cache
on protected drive problem is arguably wrong"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: MAINTAINERS: Update qla2xxx driver
scsi: zfcp: fix reaction on bit error threshold notification
scsi: core: save/restore command resid for error handling
scsi: qla2xxx: Remove WARN_ON_ONCE in qla2x00_status_cont_entry()
scsi: sd: Ignore a failure to sync cache due to lack of authorization
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
Clearing ch->device in ch_release() is wrong because that pointer must
remain valid until ch_remove() is called. This patch fixes the following
crash the second time a ch device is opened:
BUG: kernel NULL pointer dereference, address: 0000000000000790
RIP: 0010:scsi_device_get+0x5/0x60
Call Trace:
ch_open+0x4c/0xa0 [ch]
chrdev_open+0xa2/0x1c0
do_dentry_open+0x13a/0x380
path_openat+0x591/0x1470
do_filp_open+0x91/0x100
do_sys_open+0x184/0x220
do_syscall_64+0x5f/0x1a0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 085e56766f ("scsi: ch: add refcounting")
Cc: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191009173536.247889-1-bvanassche@acm.org
Reported-by: Rob Turk <robtu@rtist.nl>
Suggested-by: Rob Turk <robtu@rtist.nl>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building a kernel with SCSI_SNI_53C710 enabled, Kconfig warns:
WARNING: unmet direct dependencies detected for 53C700_LE_ON_BE
Depends on [n]: SCSI_LOWLEVEL [=y] && SCSI [=y] && SCSI_LASI700 [=n]
Selected by [y]:
- SCSI_SNI_53C710 [=y] && SCSI_LOWLEVEL [=y] && SNI_RM [=y] && SCSI [=y]
Add the missing depends SCSI_SNI_53C710 to 53C700_LE_ON_BE to fix it.
Link: https://lore.kernel.org/r/20191009151128.32411-1-tbogendoerfer@suse.de
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_sas_fp.c: In function MR_GetSpanBlock:
drivers/scsi/megaraid/megaraid_sas_fp.c:400:16: warning: variable debugBlk set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fp.c: In function mr_spanset_get_phy_params:
drivers/scsi/megaraid/megaraid_sas_fp.c:713:25: warning: variable fusion set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fp.c: In function MR_GetPhyParams:
drivers/scsi/megaraid/megaraid_sas_fp.c:815:25: warning: variable fusion set but not used [-Wunused-but-set-variable]
'debugBlk' is introduced by commit 9c915a8c99 ("[SCSI] megaraid_sas:
Add 9565/9285 specific code"), but never used, so remove it
'fusion' is not used since commit c365178f31 ("scsi: megaraid_sas:
use adapter_type for all gen controllers")
Link: https://lore.kernel.org/r/1570605824-89133-1-git-send-email-zhengbin13@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some arrays are not capable of returning RTPG data during state
transitioning, but rather return an 'LUN not accessible, asymmetric access
state transition' sense code. In these cases we can set the state to
'transitioning' directly and don't need to evaluate the RTPG data (which we
won't have anyway).
Link: https://lore.kernel.org/r/20191007135701.32389-1-hare@suse.de
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
alloc_workqueue is not checked for errors and as a result a potential
NULL dereference could occur.
Link: https://lore.kernel.org/r/1568824618-4366-1-git-send-email-allen.pais@oracle.com
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, MSI-X vectors name appears in /proc/interrupts is "megasas"
which is same for all the vectors. This patch provides a unique name for
all megaraid_sas controllers and their associated MSI-X interrupts.
Link: https://lore.kernel.org/r/20191007051828.12294-1-chandrakanth.patil@broadcom.com
Suggested-by: Konstantin Shalygin <k0ste@k0ste.ru>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Formatting changes, no functional changes.
Link: https://lore.kernel.org/r/157048753005.11757.2228541207280057256.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removed some unused manifest constants.
Link: https://lore.kernel.org/r/157048752420.11757.3464951542864727227.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Obtain the unique IDs from the RLL and RPL instead of VPD page 83h.
Link: https://lore.kernel.org/r/157048751833.11757.11996314786914610803.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/157048751247.11757.1727592925624138646.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/157048750649.11757.7811056360633694725.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for a timeout on LUN resets.
Link: https://lore.kernel.org/r/157048750055.11757.9689400788261610618.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add timeout field in RAID IU.
Link: https://lore.kernel.org/r/157048749461.11757.10013040278241807855.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: koshyaji <ajish.koshy@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use sas_phy_delete rather than sas_phy_free which, according to
comments, should not be called for PHYs that have been set up
successfully.
Link: https://lore.kernel.org/r/157048748876.11757.17773443136670011786.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/157048748297.11757.3872221216800537383.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This line is indented too far so it's a bit confusing.
Link: https://lore.kernel.org/r/20191004100615.GA823@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/lpfc/lpfc_nportdisc.c:290:1: warning: symbol 'lpfc_defer_pt2pt_acc' was not declared. Should it be static?
Link: https://lore.kernel.org/r/1570183477-137273-1-git-send-email-zhengbin13@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For MPI heartbeat stop Async Event, this patch would capture MPI FW dump
and chip reset. FW will tell which function to capture FW dump for.
Link: https://lore.kernel.org/r/20190912180918.6436-13-hmadhani@marvell.com
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add mailbox timeout checkout for ISP 27xx/28xx during FW dump procedure.
Without the timeout check, hardware lock can be held for long period. This
patch would shorten the dump procedure if a timeout condition is
encountered.
Link: https://lore.kernel.org/r/20190912180918.6436-12-hmadhani@marvell.com
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During driver unload, the remove flag will be set for all
scsi_qla_host/NPIV. This allows each NPIV to see the flag instead of
reaching for base_vha to search for it.
Link: https://lore.kernel.org/r/20190912180918.6436-11-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add error handling logic to ELS Passthrough relating to NVME devices.
Current code does not parse error code to take proper recovery action,
instead it re-logins with the same login parameters that encountered the
error. Ex: nport handle collision.
Link: https://lore.kernel.org/r/20190912180918.6436-10-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some storage arrays advertise FCP LUNs and NVMe namespaces behind the same
WWN. The driver now offers a user option by way of NVRAM parameter to
allow users to choose, on a per port basis, the kind of FC-4 type they
would like to prioritize for login.
Link: https://lore.kernel.org/r/20190912180918.6436-9-hmadhani@marvell.com
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Twelve patches mostly small but obvious fixes or cosmetic but small
updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXZgfWiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaVOAQDnuANx
QGEuQ1dZPALeZPOlEOsJzzpHPd3O+mQauIE96wD9FMypt/UKF9+fvlp4mCP+ya66
0fz1kmTQIcAADdYaNYM=
=aQi7
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Twelve patches mostly small but obvious fixes or cosmetic but small
updates"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix Nport ID display value
scsi: qla2xxx: Fix N2N link up fail
scsi: qla2xxx: Fix N2N link reset
scsi: qla2xxx: Optimize NPIV tear down process
scsi: qla2xxx: Fix stale mem access on driver unload
scsi: qla2xxx: Fix unbound sleep in fcport delete path.
scsi: qla2xxx: Silence fwdump template message
scsi: hisi_sas: Make three functions static
scsi: megaraid: disable device when probe failed after enabled device
scsi: storvsc: setup 1:1 mapping between hardware queue and CPU queue
scsi: qedf: Remove always false 'tmp_prio < 0' statement
scsi: ufs: skip shutdown if hba is not powered
scsi: bnx2fc: Handle scope bits when array returns BUSY or TSF
When a non-passthrough command is terminated with CHECK CONDITION, request
sense is executed by hijacking the command descriptor. Since
scsi_eh_prep_cmnd() and scsi_eh_restore_cmnd() do not save/restore the
original command resid, the value returned on failure of the original
command is lost and replaced with the value set by the execution of the
request sense command. This value may in many instances be unaligned to the
device sector size, causing sd_done() to print a warning message about the
incorrect unaligned resid before the command is retried.
Fix this problem by saving the original command residual in struct
scsi_eh_save using scsi_eh_prep_cmnd() and restoring it in
scsi_eh_restore_cmnd(). In addition, to make sure that the request sense
command is executed with a correctly initialized command structure, also
reset the residual to 0 in scsi_eh_prep_cmnd() after saving the original
command value in struct scsi_eh_save.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191001074839.1994-1-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warning:
drivers/scsi/bfa/bfad.c:1491:1: warning:
symbol 'restart_bfa' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20190930094327.46836-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 88263208dd ("scsi: qla2xxx: Complain if sp->done() is not called
from the completion path") introduced the WARN_ON_ONCE in
qla2x00_status_cont_entry(). The assumption was that there is only one
status continuations element. According to the firmware documentation it is
possible that multiple status continuations are emitted by the firmware.
Fixes: 88263208dd ("scsi: qla2xxx: Complain if sp->done() is not called from the completion path")
Link: https://lore.kernel.org/r/20190927073031.62296-1-dwagner@suse.de
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I've got a report about a UAS drive enclosure reporting back Sense: Logical
unit access not authorized if the drive it holds is password protected.
While the drive is obviously unusable in that state as a mass storage
device, it still exists as a sd device and when the system is asked to
perform a suspend of the drive, it will be sent a SYNCHRONIZE CACHE. If
that fails due to password protection, the error must be ignored.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190903101840.16483-1-oneukum@suse.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since 'commit fc8d0590d9 ("libcxgbi: Add ipv6 api to driver")' was
introduced, there is no call to csk_print_port() and csk_print_ip() is
made.
Hence kernel build with clang complains below message:
drivers/scsi/cxgbi/libcxgbi.c:2287:19: warning: unused function 'csk_print_port' [-Wunused-function]
static inline int csk_print_port(struct cxgbi_sock *csk, char *buf)
^
drivers/scsi/cxgbi/libcxgbi.c:2298:19: warning: unused function 'csk_print_ip' [-Wunused-function]
static inline int csk_print_ip(struct cxgbi_sock *csk, char *buf)
^
Remove csk_print_port() and csk_print_ip() to stop warning.
Link: https://lore.kernel.org/r/20190924093716.GA78230@LGEARND20B15
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add sysfs attributes for the ATA information page and Supported VPD Pages
page.
Link: https://lore.kernel.org/r/20190926162216.56591-1-ryanattard@ryanattard.info
Signed-off-by: Ryan Attard <ryanattard@ryanattard.info>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are some statements that are indented too deeply, remove the
extraneous tabs and rejoin split lines.
Link: https://lore.kernel.org/r/20190927095840.26377-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Couple of users had requested to print the SCSI command age along with
command failure errors. This is a small change, but allows users to get
more important information about the command that was failed, it would help
the users in debugging the command failures:
Link: https://lore.kernel.org/r/20190926052501.GA8352@machine1
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add qedf_get_host_port_id() to the transport template.
The fc_transport_template initializes the port_id member to the default
value of -1. The new getter ensures that the sysfs entry shows the current
value and not the default one, e.g by using 'lsscsi -H -t'
Link: https://lore.kernel.org/r/20190924072906.23737-1-dwagner@suse.de
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rework from previous work by:
Sujit Reddy Thumma <sthumma@codeaurora.org>
Override auto suspend tunables for UFS device LUNs during initialization so
as to efficiently manage background operations and the power consumption.
Link: https://lore.kernel.org/r/1568649411-5127-3-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rework from previous work by:
Sujit Reddy Thumma <sthumma@codeaurora.org>
Until now the scsi mid-layer forbids runtime suspend till userspace enables
it. This is mainly to quarantine some disks with broken runtime power
management or have high latencies executing suspend resume callbacks. If
the userspace doesn't enable the runtime suspend the underlying hardware
will be always on even when it is not doing any useful work and thus
wasting power.
Some low-level drivers for the controllers can efficiently use runtime
power management to reduce power consumption and improve battery life.
Allow runtime suspend parameters override within the LLD itself instead of
waiting for userspace to control the power management.
Link: https://lore.kernel.org/r/1568649411-5127-2-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simplify this function implementation by using a known function.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
[mkp: applied by hand]
Link: https://lore.kernel.org/r/9e667f19-434e-ed30-78cb-9ddc6323c51e@web.de
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't populate the array setup_attrs on the stack but instead make it
static const. Makes the object code smaller by 180 bytes.
Before:
text data bss dec hex filename
2140 224 0 2364 93c drivers/scsi/ufs/ufshcd-dwc.o
After:
text data bss dec hex filename
1863 320 0 2183 887 drivers/scsi/ufs/ufshcd-dwc.o
(gcc version 9.2.1, amd64)
Link: https://lore.kernel.org/r/20190906170104.10450-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't populate the array 'options' on the stack but instead make it static
const. Makes the object code smaller by 143 bytes.
Before:
text data bss dec hex filename
94483 11272 1184 106939 1a1bb drivers/scsi/ips.o
After:
text data bss dec hex filename
94244 11368 1184 106796 1a12c drivers/scsi/ips.o
(gcc version 9.2.1, amd64)
Link: https://lore.kernel.org/r/20190906164522.5644-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't populate the array dev_cmd_err on the stack but instead make it
static const. Makes the object code smaller by 80 bytes.
Before:
text data bss dec hex filename
21461 1564 0 23025 59f1 drivers/scsi/fnic/vnic_dev.o
After:
text data bss dec hex filename
21318 1628 0 22946 59a2 drivers/scsi/fnic/vnic_dev.o
(gcc version 9.2.1, amd64)
Link: https://lore.kernel.org/r/20190906163945.3889-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable rc is being initialized with a value that is never read and is
being re-assigned a little later on. The assignment is redundant and hence
can be removed.
Link: https://lore.kernel.org/r/20190905135017.23772-1-colin.king@canonical.com
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pointer host is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant and
hence can be removed.
Link: https://lore.kernel.org/r/20190905134229.21194-1-colin.king@canonical.com
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/smartpqi/smartpqi_init.c: In function 'pqi_driver_version_show':
drivers/scsi/smartpqi/smartpqi_init.c:6164:24: warning:
variable 'ctrl_info' set but not used [-Wunused-but-set-variable]
commit 6d90615f13 ("scsi: smartpqi: add sysfs entries") added it but
it was never used. Also remove variable 'shost'.
[mkp: commit desc]
Link: https://lore.kernel.org/r/20190831130348.20552-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a statement that is indented one level too deeply, remove the tab,
re-join broken line and remove some empty lines.
Link: https://lore.kernel.org/r/20190831073903.7834-1-colin.king@canonical.com
Addresses-Coverity: ("Indentation does not match nesting")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Load driver with module parameter "max_msix_vectors". Value provided in
module parameter is not used by mpt3sas driver. Driver loads with max
controller supported MSI-X value.
In _base_alloc_irq_vectors use reply_queue_count which is determined using
user provided msix value insted of ioc->msix_vector_count which tells max
supported msix value of the controller.
Link: https://lore.kernel.org/r/1568379890-18347-13-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If any faulty application issues an NVMe Encapsulated commands to HBA which
doesn't support NVMe protocol then driver should return the command as
invalid with the following message.
"HBA doesn't support NVMe. Rejecting NVMe Encapsulated request."
Otherwise below page fault kernel panic will be observed while building the
PRPs as there is no PRP pools allocated for the HBA which doesn't support
NVMe drives.
RIP: 0010:_base_build_nvme_prp+0x3b/0xf0 [mpt3sas]
Call Trace:
_ctl_do_mpt_command+0x931/0x1120 [mpt3sas]
_ctl_ioctl_main.isra.11+0xa28/0x11e0 [mpt3sas]
? prepare_to_wait+0xb0/0xb0
? tty_ldisc_deref+0x16/0x20
_ctl_ioctl+0x1a/0x20 [mpt3sas]
do_vfs_ioctl+0xaa/0x620
? vfs_read+0x117/0x140
ksys_ioctl+0x67/0x90
__x64_sys_ioctl+0x1a/0x20
do_syscall_64+0x60/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
[mkp: tweaked error string]
Link: https://lore.kernel.org/r/1568379890-18347-12-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The firmware image layout has been changed for Aero controllers. All
compatible HBAs have to get Firmware Package version from Component Image
Header layout.
The Signature field in FW header is set to 0xEB000042 for products
compatible with Component Image Header.
For compatible controllers, driver fetches firmware package version from
ApplicationSpecific field of Component Image Header.
Link: https://lore.kernel.org/r/1568379890-18347-11-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added a new status flag named MPT3_DIAG_BUFFER_IS_APP_OWNED and it will set
whenever application registers the diag buffer & it will be cleared when
application unregisters the buffer.
When this flag is enabled, and if application issues diag buffer register
command without releasing the buffer, then register command will be failed
with -EINVAL status by saying that this buffer is already registered by the
application.
When user issues a trace buffer register command through sysfs parameter,
and if trace buffer is in released stated but not yet unregistered by the
application which was owning it, then driver will unregister the buffer by
itself and freshly register the 1MB sized trace buffer with the HBA
firmware.
Link: https://lore.kernel.org/r/1568379890-18347-9-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The diag buffer which is allocated during driver load time or through sysfs
parameter is marked as driver allocated diag buffer.
MPT3_DIAG_BUFFER_IS_DRIVER_ALLOCATED bit will be set for this buffer.
This buffer won't be de-allocated even when application issues unregister
command, driver just clears the registered status bit. Same buffer will be
reused while re-registering the same diag buffer type by any application.
While re-registering the same diag buffer type application has to register
with the same size that the buffer was allocated during driver load
time. This buffer size can be read by the application by issuing diag
'query' command.
This always makes sure that the memory is available for applications for
collecting the firmware logs. Only thing is that this won't allow the
application to re-register the diag buffer with different size, but the
buffer size which is allocated during driver load time will be enough for
most of the cases for collecting the firmware logs.
Link: https://lore.kernel.org/r/1568379890-18347-8-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clear MPT3_DIAG_BUFFER_IS_RELEASED bit once diag buffer is re-registered
after reading the buffer, else driver won't release the buffer and return
the 'diag release' command with -EINVAL status saying that buffer is
already released.
Link: https://lore.kernel.org/r/1568379890-18347-7-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Application A has registered a diag buffer and looking for particular event
to happen to release & read the trace buffer. Meanwhile application B has
unregistered the diag buffer and now Application A can't get the required
diag buffer. So proper diag buffer ownership is missing.
Each application has to maintain its own Unique ID. Now driver has to save
the Application's UniqueID for each diag buffer type when diag buffer is
registered. And driver has to allow 'release', 'read' & 'unregister' diag
commands only if application's UniqueID matches with saved UniqueID for the
corresponding diag buffer type.
When diag buffer is registered by the driver, then the UniqueID saved by
the driver is "BRCM" (i.e. 0x4252434D) for SAS3 and above generations HBA
devices. For SAS2 HBAs, driver keeps the legacy UniqueID 0x07075900 for
maintaining compatibility with the legacy SAS2 application and this
improvement won't be applicable for SAS2 HBA devices.
Any application can own the buffer registered by the driver by sending
diag register request to driver with same buffer type and size
(Application can get the buffer size by sending 'query' command). Then
driver changes the ownership of the buffer by saving application's
UniqueID for that corresponding buffer type.
Also, application can re-register the diag buffer with same size without
un-registering it, but diag buffer should be released before re-registering
it. By allowing this, driver no need to deallocate and allocate a new
buffer for re-register command, same buffer can be re-used.
Link: https://lore.kernel.org/r/1568379890-18347-6-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Memory leak can happen when diag buffer is released but not unregistered
(where buffer is deallocated) by the user. During module unload time driver
is not deallocating the buffer if the buffer is in released state.
Deallocate the diag buffer during module unload time without any diag
buffer status checks.
Link: https://lore.kernel.org/r/1568379890-18347-5-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When user issues diag register command from application with required size,
and if driver unable to allocate the memory, then it will fail the register
command. While failing the register command, driver is not currently
clearing MPT3_CMD_PENDING bit in ctl_cmds.status variable which was set
before trying to allocate the memory. As this bit is set, subsequent
register command will be failed with BUSY status even when user wants to
register the trace buffer will less memory.
Clear MPT3_CMD_PENDING bit in ctl_cmds.status before returning the diag
register command with no memory status.
Link: https://lore.kernel.org/r/1568379890-18347-4-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Display message before releasing the diag buffer so that user knows which
event caused the release of diag buffer.
Releasing of diag buffer means HBA firmware stops posting the firmware logs
on the registered diag buffer.
Link: https://lore.kernel.org/r/1568379890-18347-3-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if user wishes to enable the host trace buffer during driver load
time, then user has to load the driver with module parameter
'diag_buffer_enable' set to one.
Alternatively now the user can enable host trace buffer by enabling the
following fields in manufacturing page11 in NVDATA (nvdata xml is used
while building HBA firmware image):
* HostTraceBufferMaxSizeKB - Maximum trace buffer size in KB that host can
allocate,
* HostTraceBufferMinSizeKB - Minimum trace buffer size in KB atleast host
should allocate,
* HostTraceBufferDecrementSizeKB - size by which host can reduce from
buffer size and retry the buffer allocation
when buffer allocation failed with previous
calculated buffer size.
The driver will register the trace buffer automatically without any module
parameter during boot time when above fields are enabled in manufacturing
page11 in HBA firmware.
Driver follows the following algorithm for enabling the host trace buffer
during driver load time:
* If user has loaded the driver with module parameter 'diag_buffer_enable'
set to one, then driver allocates 2MB buffer and registers this buffer
with HBA firmware for capturing the firmware trace logs.
* Else driver reads manufacture page11 data and checks whether
HostTraceBufferMaxSizeKB filed is zero or not?
- If HostTraceBufferMaxSizeKB is non-zero then driver tries to allocate
HostTraceBufferMaxSizeKB size of memory. If the buffer allocation is
successful, then it will register this buffer with HBA firmware, else
in a loop the driver will try again by reducing the current buffer size
with HostTraceBufferDecrementSizeKB size until memory allocation is
successful or buffer size falls below HostTraceBufferMinSizeKB. If the
memory allocation is successful, then the buffer will be registered
with the firmware. Else, if the buffer size falls below the
HostTraceBufferMinSizeKB, then driver won't register trace buffer with
HBA firmware.
- If HostTraceBufferMaxSizeKB is zero, then driver won't register trace
buffer with HBA firmware.
Link: https://lore.kernel.org/r/1568379890-18347-2-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Local variable fcp_txcmplq_cnt is initialized to 0 and then displayed in
lpfc driver message 0387.
Presumed residual (or unused) code from previous commit.
Removed fcp_txcmplq_cnt.
Link: https://lore.kernel.org/r/20190922035906.10977-20-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
T10 PI support on SLI-4-based FCoE adapters is not supported. A prior
commit in the 12.4.0.0 stream added device recognition that would prevent
T10 PI enablement. However, it didn't contain a complete device list. Thus
some SLI-4 FCoE adapters still had T10 PI enabled.
Fix by expanding the device list that identifies FCoE devices.
Link: https://lore.kernel.org/r/20190922035906.10977-19-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch updates ACQE handling for:
- an EEPROM failure error reported by the adapter.
- ensures that all data for any ACQE, recognized or not, is logged.
- Given that all data is now logged unconditionally, the default case
(unrecognized) data can be reduced.
Link: https://lore.kernel.org/r/20190922035906.10977-18-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In lpfc_release_io_buf, an lpfc_io_buf is returned to the 'available' pool
before any associated sgl or cmd and rsp buffers are returned via their
respective 'put' routines. If xri rebalancing occurs and an lpfc_io_buf
structure is reused quickly, there may be a race condition between release
of old and association of new resources.
Re-ordered lpfc_release_io_buf to release sgl and cmd/rsp
buffer lists before releasing the lpfc_io_buf structure for re-use.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Link: https://lore.kernel.org/r/20190922035906.10977-17-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many of the sgl-per-hdwq paths are locking with spin_lock_irq() and
spin_unlock_irq() and may unwittingly raising irq when it shouldn't. Hard
deadlocks were seen around lpfc_scsi_prep_cmnd().
Fix by converting the locks to irqsave/irqrestore.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Link: https://lore.kernel.org/r/20190922035906.10977-16-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While reviewing the CT behavior, issues with spinlock_irq were seen. The
driver should be using spinlock_irqsave/irqrestore in the els flush
routine.
Changed to spinlock_irqsave/irqrestore.
Link: https://lore.kernel.org/r/20190922035906.10977-15-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After study, it was determined there was a double free of a CT iocb during
execution of lpfc_offline_prep and lpfc_offline. The prep routine issued
an abort for some CT iocbs, but the aborts did not complete fast enough for
a subsequent routine that waits for completion. Thus the driver proceeded
to lpfc_offline, which releases any pending iocbs. Unfortunately, the
completions for the aborts were then received which re-released the ct
iocbs.
Turns out the issue for why the aborts didn't complete fast enough was not
their time on the wire/in the adapter. It was the lpfc_work_done routine,
which requires the adapter state to be UP before it calls
lpfc_sli_handle_slow_ring_event() to process the completions. The issue is
the prep routine takes the link down as part of it's processing.
To fix, the following was performed:
- Prevent the offline routine from releasing iocbs that have had aborts
issued on them. Defer to the abort completions. Also means the driver
fully waits for the completions. Given this change, the recognition of
"driver-generated" status which then releases the iocb is no longer
valid. As such, the change made in the commit 296012285c is reverted.
As recognition of "driver-generated" status is no longer valid, this
patch reverts the changes made in
commit 296012285c ("scsi: lpfc: Fix leak of ELS completions on adapter reset")
- Modify lpfc_work_done to allow slow path completions so that the abort
completions aren't ignored.
- Updated the fdmi path to recognize a CT request that fails due to the
port being unusable. This stops FDMI retries. FDMI will be restarted on
next link up.
Link: https://lore.kernel.org/r/20190922035906.10977-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scenarios were seen where a host hung when the system booted or the host
was very slow in booting. The link would not come up and no luns were
visible to the host.
After investigation, this was found to be due to the introduction of a new
ACQE that adapter may generate to report a adapter hw warning. The ACQE was
delivered to the driver very early in adapter initialization, when the
driver did not expect command completion. As part of handling this
unexpected interrupt the an EQEs are consumed and discarded and the EQ
rearmed. The issue is the CQ that cause the EQE and thus the interrupt was
not processed and the CQ was left unarmed. Meaning it would no longer
generate a new interrupt condition. Subsequent mailbox commands used to
initialize the adapter use the same CQ, and as there was no completion
interrupt generated, the driver never saw the mailbox commands complete and
it would wait long command timeouts.
Fix by having the early flush routine also process the related CQ and rearm
the CQ.
Link: https://lore.kernel.org/r/20190922035906.10977-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity flagged several scenarios where checking of null pointer values
wasn't consistent.
Fix the code to that be consistent on checking.
Link: https://lore.kernel.org/r/20190922035906.10977-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the port, running as a nvme target, receives an ABTS, it submits
commands to the adapter to Abort i/o outstanding in the adapter. The Abort
command formatting routine left a command field set to zero, which
instructs the adapter to generate an ABTS on the wire as part of cleaning
up the I/O. This is common operation for an initiator, but not for a
target.
Fix the driver to check whether an ABTS had been received for the I/O, and
if so, change the Abort command formatting so that the ABTS generation is
disabled (IA=1). No need to ABTS it when the other side already has.
Also refactored the code such that there is a single routine being used for
nvme or nvmet ABORT requests, and IA is an argument.
Link: https://lore.kernel.org/r/20190922035906.10977-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An issue was seen discovering all SCSI Luns when a target device undergoes
link bounce.
The driver currently does not qualify the FC4 support on the target.
Therefore it will send a SCSI PRLI and an NVMe PRLI. The expectation is
that the target will reject the PRLI if it is not supported. If a PRLI
times out, the driver will retry. The driver will not proceed with the
device until both SCSI and NVMe PRLIs are resolved. In the failure case,
the device is FCP only and does not respond to the NVMe PRLI, thus
initiating the wait/retry loop in the driver. During that time, a RSCN is
received (device bounced) causing the driver to issue a GID_FT. The GID_FT
response comes back before the PRLI mess is resolved and it prematurely
cancels the PRLI retry logic and leaves the device in a STE_PRLI_ISSUE
state. Discovery with the target never completes or resets.
Fix by resetting the node state back to STE_NPR_NODE when GID_FT completes,
thereby restarting the discovery process for the node.
Link: https://lore.kernel.org/r/20190922035906.10977-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Faults are seen with RIP of lpfc_scsi_cmd_iocb_cmpl(). The failure is when
lpfc_update_status is being called as part of the completion. After
debugging, it was seen the issue was the shost pointer that the driver
derived from the scsi cmd. The crash showed the cmd->device pointer being
bogus, which is likely as the scsi devices were offlined prior. The bogus
device pointer caused subsequent pointers derived from the location,
specifically the vport, to be bogus.
Fix by adjusting the calling sequence to pass in the vport rather than
having to derive it from the cmd structure.
Link: https://lore.kernel.org/r/20190922035906.10977-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Symptoms were seen of the driver not having valid data for mailbox
commands. After debugging, the following sequence was found:
The driver maintains a port-wide pointer of the mailbox command that is
currently in execution. Once finished, the port-wide pointer is cleared
(done in lpfc_sli4_mq_release()). The next mailbox command issued will set
the next pointer and so on.
The mailbox response data is only copied if there is a valid port-wide
pointer.
In the failing case, it was seen that a new mailbox command was being
attempted in parallel with the completion. The parallel path was seeing
the mailbox no long in use (flag check under lock) and thus set the port
pointer. The completion path had cleared the active flag under lock, but
had not touched the port pointer. The port pointer is cleared after the
lock is released. In this case, the completion path cleared the just-set
value by the parallel path.
Fix by making the calls that clear mbox state/port pointer while under
lock. Also slightly cleaned up the error path.
Link: https://lore.kernel.org/r/20190922035906.10977-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When target-side fault injections are made, the driver isn't reconnecting
to the remote port. The driver is logging "2753" error messages which
state:
"PLOGI failure DID:1B2400 Status:x3/xf0240008"
The failures status is indicating a Illegal field error, which points to
the Temporary RPI field being used for the ELS. This error typically means
the driver used an RPI that was already registered (shouldn't be registered
if using it in this context).
Study has found that if the driver were in discovery attempts and
encountered an error, it wouldn't flag the temporary rpi in error. Yet the
rpi was released for reallocation in these error paths and another ELS
could allocate the rpi. In the failure situation a retry was done on an ELS
that had encountered an error, and as the rpi wasn't marked in error, the
ELS reused the rpi it originally allocated. But that rpi had been allocated
by a different ELS issued after the original error and before the retry
attempt. The different ELS had succeeded and the RPI was registered.
Fix by marking the rpi state for the node to be in error, aka as needing
reallocation, upon an error in the els processing. Error state marking is
always done prior to release back to the internal rpi free list, which the
driver wasn't doing in cases prior.
Also enhanced some of the logging to help in the next case of problem
troubleshooting.
Link: https://lore.kernel.org/r/20190922035906.10977-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior use-after-free mailbox fix solved it's problem by null'ing a ndlp
pointer. However, further testing has shown that this change causes a
later state change to occasionally be skipped, which results in a reference
count never being decremented thus the rpi is never released, which causes
a vport delete to never succeed.
Revise the fix in the prior patch to no longer null the ndlp. Instead the
RELEASE_RPI flag is set which will drive the release of the rpi.
Given the new code was added at a deep indentation level, refactor the code
block using a new routine that avoids the indentation issues.
Fixes: 9b16406864 ("scsi: lpfc: Fix use-after-free mailbox cmd completion")
Link: https://lore.kernel.org/r/20190922035906.10977-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nvme-fc transport may call to abort an io on controller reset. If the
driver is out of resources to issue an abort command, it just gives up and
does nothing. The transport expects the lldd to always be able to terminate
an io it has issued. At that point, the controller hangs waiting for
aborted ios to be returned. Note: flaged by "6136" and "6176" error
messages.
Root issue was the adapter mis-allocated the number resources it allocated
for command entries for the adapter.
Convert the driver to allocate command resources based on the number of
xris supported by the FC port - 1 resource for the original command and 1
resource for the abort request.
Link: https://lore.kernel.org/r/20190922035906.10977-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity flagged missing status check on register read that flags a
poisoned data return value.
Add checking of register read status.
Link: https://lore.kernel.org/r/20190922035906.10977-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use of spin_lock_irq may re-enable interrupts prematurely.
Convert to spin_lock. Note: code is under the phba->hba_lock which has been
locked with irqsave.
Link: https://lore.kernel.org/r/20190922035906.10977-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After exchanging PLOGI on an SLI-3 adapter, the PRLI exchange failed. Link
trace showed the port was assigned a non-zero n_port_id, but didn't use the
address on the PRLI. The assigned address is set on the port by the
CONFIG_LINK mailbox command. The driver responded to the PRLI before the
mailbox command completed. Thus the PRLI response used the old n_port_id.
Defer the PRLI response until CONFIG_LINK completes.
Link: https://lore.kernel.org/r/20190922035906.10977-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----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=aAPP
-----END PGP SIGNATURE-----
Merge tag 'for-5.4/post-2019-09-24' of git://git.kernel.dk/linux-block
Pull more block updates from Jens Axboe:
"Some later additions that weren't quite done for the first pull
request, and also a few fixes that have arrived since.
This contains:
- Kill silly pktcdvd warning on attempting to register a non-scsi
passthrough device (me)
- Use symbolic constants for the block t10 protection types, and
switch to handling it in core rather than in the drivers (Max)
- libahci platform missing node put fix (Nishka)
- Small series of fixes for BFQ (Paolo)
- Fix possible nbd crash (Xiubo)"
* tag 'for-5.4/post-2019-09-24' of git://git.kernel.dk/linux-block:
block: drop device references in bsg_queue_rq()
block: t10-pi: fix -Wswitch warning
pktcdvd: remove warning on attempting to register non-passthrough dev
ata: libahci_platform: Add of_node_put() before loop exit
nbd: fix possible page fault for nbd disk
nbd: rename the runtime flags as NBD_RT_ prefixed
block, bfq: push up injection only after setting service time
block, bfq: increase update frequency of inject limit
block, bfq: reduce upper bound for inject limit to max_rq_in_driver+1
block, bfq: update inject limit only after injection occurred
block: centralize PI remapping logic to the block layer
block: use symbolic constants for t10_pi type
For N2N, the NPort ID is assigned by driver in the PLOGI ELS. According to
FW Spec the byte order for SID is not the same as DID.
Link: https://lore.kernel.org/r/20190912180918.6436-8-hmadhani@marvell.com
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Tested-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During link up/bounce, qla driver would do command flush as part of
cleanup. In this case, the flush can intefere with FW state. This patch
allows FW to be in control of link up.
Link: https://lore.kernel.org/r/20190912180918.6436-7-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix stalled link recovery for N2N with FC-NVMe connection.
Link: https://lore.kernel.org/r/20190912180918.6436-6-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the case of NPIV port is being torn down, this patch will set a flag to
indicate VPORT_DELETE. This would prevent relogin to be triggered.
Link: https://lore.kernel.org/r/20190912180918.6436-5-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On driver unload, 'remove_one' thread was allowed to advance, while session
cleanup still lag behind. This patch ensures session deletion will finish
before remove_one can advance.
Link: https://lore.kernel.org/r/20190912180918.6436-4-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are instances, though rare, where a LOGO request cannot be sent out
and the thread in free session done can wait indefinitely. Fix this by
putting an upper bound to sleep.
Link: https://lore.kernel.org/r/20190912180918.6436-3-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print if fwdt template is present or not, only when
ql2xextended_error_logging is enabled.
Link: https://lore.kernel.org/r/20190912180918.6436-2-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/hisi_sas/hisi_sas_main.c:3686:6:
warning: symbol 'hisi_sas_debugfs_release' was not declared. Should it be static?
drivers/scsi/hisi_sas/hisi_sas_main.c:3708:5:
warning: symbol 'hisi_sas_debugfs_alloc' was not declared. Should it be static?
drivers/scsi/hisi_sas/hisi_sas_main.c:3799:6:
warning: symbol 'hisi_sas_debugfs_bist_init' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20190923054035.19036-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
storvsc doesn't use a dedicated hardware queue for a given CPU queue. When
issuing I/O, it selects returning CPU (hardware queue) dynamically based on
vmbus channel usage across all channels.
This patch advertises num_present_cpus() as number of hardware queues. This
will have upper layer setup 1:1 mapping between hardware queue and CPU
queue and avoid unnecessary locking when issuing I/O.
Link: https://lore.kernel.org/r/1567790660-48142-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since tmp_prio is declared as u8, the following statement is always false.
tmp_prio < 0
So remove 'always false' statement.
Link: https://lore.kernel.org/r/20190919075548.GA112801@LGEARND20B15
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In some cases, hba may go through shutdown flow without successful
initialization and then make system hang.
For example, if ufshcd_change_power_mode() gets error and leads to
ufshcd_hba_exit() to release resources of the host, future shutdown flow
may hang the system since the host register will be accessed in unpowered
state.
To solve this issue, simply add checking to skip shutdown for above kind of
situation.
Link: https://lore.kernel.org/r/1568780438-28753-1-git-send-email-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The qla2xxx driver had this issue as well when the newer array firmware
returned the retry_delay_timer in the fcp_rsp. The bnx2fc is not handling
the masking of the scope bits either so the retry_delay_timestamp value
lands up being a large value added to the timer timestamp delaying I/O for
up to 27 Minutes. This patch adds similar code to handle this to the
bnx2fc driver to avoid the huge delay.
Link: https://lore.kernel.org/r/1568210202-12794-1-git-send-email-loberman@redhat.com
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Reported-by: David Jeffery <djeffery@redhat.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was missing from scsi_device_from_queue() due to the introduction of
another new scsi_mq_ops_no_commit of linux-next commit 8930a6c207 ("scsi:
core: add support for request batching") from Martin's scsi/5.4/scsi-queue
or James' scsi/misc.
Only devicehandler code seems to call scsi_device_from_queue():
*** drivers/scsi/scsi_dh.c:
scsi_dh_activate[255] sdev = scsi_device_from_queue(q);
scsi_dh_set_params[302] sdev = scsi_device_from_queue(q);
scsi_dh_attach[325] sdev = scsi_device_from_queue(q);
scsi_dh_attached_handler_name[363] sdev = scsi_device_from_queue(q);
Fixes multipath tools follow-on errors:
$ multipath -v6
...
libdevmapper: ioctl/libdm-iface.c(1887): device-mapper: reload ioctl on mpatha failed: No such device
...
mpatha: failed to load map, error 19
...
showing also as kernel messages:
device-mapper: table: 252:0: multipath: error attaching hardware handler
device-mapper: ioctl: error adding target to table
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 8930a6c207 ("scsi: core: add support for request batching")
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was missing from scsi_mq_ops_no_commit of linux-next commit
8930a6c207 ("scsi: core: add support for request batching") from Martin's
scsi/5.4/scsi-queue or James' scsi/misc.
See also linux-next commit b7e9e1fb7a ("scsi: implement .cleanup_rq
callback") from block/for-next.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 8930a6c207 ("scsi: core: add support for request batching")
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates.
The only core change this time around is the addition of request
batching for virtio. Since batching requires an additional flag to
use, it should be invisible to the rest of the drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXYQE/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXs9AP4usPY5
OpMlF6OiKFNeJrCdhCScVghf9uHbc7UA6cP+EgD/bCtRgcDe1ZjOTYWdeTwvwWqA
ltWYonnv6Lg3b1f9yqI=
=jRC/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
Currently t10_pi_prepare/t10_pi_complete functions are called during the
NVMe and SCSi layers command preparetion/completion, but their actual
place should be the block layer since T10-PI is a general data integrity
feature that is used by block storage protocols. Introduce .prepare_fn
and .complete_fn callbacks within the integrity profile that each type
can implement according to its needs.
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Fixed to not call queue integrity functions if BLK_DEV_INTEGRITY
isn't defined in the config.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
-----BEGIN PGP SIGNATURE-----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=Qt+h
-----END PGP SIGNATURE-----
Merge tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Two NVMe pull requests:
- ana log parse fix from Anton
- nvme quirks support for Apple devices from Ben
- fix missing bio completion tracing for multipath stack devices
from Hannes and Mikhail
- IP TOS settings for nvme rdma and tcp transports from Israel
- rq_dma_dir cleanups from Israel
- tracing for Get LBA Status command from Minwoo
- Some nvme-tcp cleanups from Minwoo, Potnuri and Myself
- Some consolidation between the fabrics transports for handling
the CAP register
- reset race with ns scanning fix for fabrics (move fabrics
commands to a dedicated request queue with a different lifetime
from the admin request queue)."
- controller reset and namespace scan races fixes
- nvme discovery log change uevent support
- naming improvements from Keith
- multiple discovery controllers reject fix from James
- some regular cleanups from various people
- Series fixing (and re-fixing) null_blk debug printing and nr_devices
checks (André)
- A few pull requests from Song, with fixes from Andy, Guoqing,
Guilherme, Neil, Nigel, and Yufen.
- REQ_OP_ZONE_RESET_ALL support (Chaitanya)
- Bio merge handling unification (Christoph)
- Pick default elevator correctly for devices with special needs
(Damien)
- Block stats fixes (Hou)
- Timeout and support devices nbd fixes (Mike)
- Series fixing races around elevator switching and device add/remove
(Ming)
- sed-opal cleanups (Revanth)
- Per device weight support for BFQ (Fam)
- Support for blk-iocost, a new model that can properly account cost of
IO workloads. (Tejun)
- blk-cgroup writeback fixes (Tejun)
- paride queue init fixes (zhengbin)
- blk_set_runtime_active() cleanup (Stanley)
- Block segment mapping optimizations (Bart)
- lightnvm fixes (Hans/Minwoo/YueHaibing)
- Various little fixes and cleanups
* tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block: (186 commits)
null_blk: format pr_* logs with pr_fmt
null_blk: match the type of parameter nr_devices
null_blk: do not fail the module load with zero devices
block: also check RQF_STATS in blk_mq_need_time_stamp()
block: make rq sector size accessible for block stats
bfq: Fix bfq linkage error
raid5: use bio_end_sector in r5_next_bio
raid5: remove STRIPE_OPS_REQ_PENDING
md: add feature flag MD_FEATURE_RAID0_LAYOUT
md/raid0: avoid RAID0 data corruption due to layout confusion.
raid5: don't set STRIPE_HANDLE to stripe which is in batch list
raid5: don't increment read_errors on EILSEQ return
nvmet: fix a wrong error status returned in error log page
nvme: send discovery log page change events to userspace
nvme: add uevent variables for controller devices
nvme: enable aen regardless of the presence of I/O queues
nvme-fabrics: allow discovery subsystems accept a kato
nvmet: Use PTR_ERR_OR_ZERO() in nvmet_init_discovery()
nvme: Remove redundant assignment of cq vector
nvme: Assign subsys instance from first ctrl
...
-----BEGIN PGP SIGNATURE-----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=L5e+
-----END PGP SIGNATURE-----
Merge tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 updates from Tony Luck:
"The big change here is removal of support for SGI Altix"
* tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: (33 commits)
genirq: remove the is_affinity_mask_valid hook
ia64: remove CONFIG_SWIOTLB ifdefs
ia64: remove support for machvecs
ia64: move the screen_info setup to common code
ia64: move the ROOT_DEV setup to common code
ia64: rework iommu probing
ia64: remove the unused sn_coherency_id symbol
ia64: remove the SGI UV simulator support
ia64: remove the zx1 swiotlb machvec
ia64: remove CONFIG_ACPI ifdefs
ia64: remove CONFIG_PCI ifdefs
ia64: remove the hpsim platform
ia64: remove now unused machvec indirections
ia64: remove support for the SGI SN2 platform
drivers: remove the SGI SN2 IOC4 base support
drivers: remove the SGI SN2 IOC3 base support
qla2xxx: remove SGI SN2 support
qla1280: remove SGI SN2 support
misc/sgi-xp: remove SGI SN2 support
char/mspec: remove SGI SN2 support
...
Currently blk_set_runtime_active() is checking if q->dev is null by
itself, thus remove the same checking in its user: scsi_dev_type_resume().
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When device gone, it will check whether it is during reset, if not, it will
send internal task abort. Before internal task abort returned, reset
begins, and it will check whether SAS_PHY_UNUSED is set, if not, it will
call hisi_sas_init_device(), but at that time domain_device may already be
freed or part of it is freed, so it may referenece null pointer in
hisi_sas_init_device(). It may occur as follows:
thread0 thread1
hisi_sas_dev_gone()
check whether in RESET(no)
internal task abort
reset prep
soft_reset
... (part of reset_done)
internal task abort failed
release resource anyway
clear_itct
device->lldd_dev=NULL
hisi_sas_reset_init_all_device
check sas_dev->dev_type is SAS_PHY_UNUSED and
!device
set dev_type SAS_PHY_UNUSED
sas_free_device
hisi_sas_init_device
...
Semaphore hisi_hba.sema is used to sync the processes of device gone and
host reset.
To solve the issue, expand the scope that semaphore protects and let them
never occur together.
And also some places will check whether domain_device is NULL to judge
whether the device is gone. So when device gone, need to clear
sas_dev->sas_device.
Link: https://lore.kernel.org/r/1567774537-20003-14-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add BIST (built in self test) support for phy loopback.
Through the new debugfs interface, the user can configure loopback
mode/linkrate/phy id/code mode before enabling it. And also user can
enable/disable BIST function.
Link: https://lore.kernel.org/r/1567774537-20003-13-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We extract the code of memory allocate and construct an new function for
it. We think it's convenient for subsequent optimization.
Link: https://lore.kernel.org/r/1567774537-20003-12-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some function arguments are unused, so remove them.
Also move the timeout print in for wait_cmds_complete_timeout_vX_hw()
callsites into that same function.
Link: https://lore.kernel.org/r/1567774537-20003-11-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the NCQ tag is only assigned for FPDMA READ and FPDMA WRITE
commands, and for other NCQ commands (such as FPDMA SEND), their NCQ tags
are set in the delivery command to 0.
So for all the NCQ commands, we also need to assign normal NCQ tag for
them, so drop the command type check in hisi_sas_get_ncq_tag() [drop
hisi_sas_get_ncq_tag() altogether actually], and always use the ATA command
NCQ tag when appropriate.
Link: https://lore.kernel.org/r/1567774537-20003-8-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After suspend and resume, the HW registers will be set back to their
initial value. We use init_reg_v3_hw() to set some registers, but some
registers are set via firmware in ACPI "_RST" method, so add reset handler
before init_reg_v3_hw().
Link: https://lore.kernel.org/r/1567774537-20003-7-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When init device for SAS disks, it will send TMF IO to clear disks. At that
time TMF IO is broken by some operations such as injecting controller reset
from HW RAs event, the TMF IO will be timeout, and at last device will be
gone. Print is as followed:
hisi_sas_v3_hw 0000:74:02.0: dev[240:1] found
...
hisi_sas_v3_hw 0000:74:02.0: controller resetting...
hisi_sas_v3_hw 0000:74:02.0: phyup: phy7 link_rate=10(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy0 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy1 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy2 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy3 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy6 link_rate=10(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy5 link_rate=11
hisi_sas_v3_hw 0000:74:02.0: phyup: phy4 link_rate=11
hisi_sas_v3_hw 0000:74:02.0: controller reset complete
hisi_sas_v3_hw 0000:74:02.0: abort tmf: TMF task timeout and not done
hisi_sas_v3_hw 0000:74:02.0: dev[240:1] is gone
sas: driver on host 0000:74:02.0 cannot handle device 5000c500a75a860d,
error:5
To improve the reliability, retry TMF IO max of 3 times for SAS disks which
is the same as softreset does.
Link: https://lore.kernel.org/r/1567774537-20003-6-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At expander environment, we delay after issue phy reset to wait for
hardware to handle phy reset. But if sas_smp_phy_control() fails, the
delay is unnecessary so remove it.
Link: https://lore.kernel.org/r/1567774537-20003-5-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At hisi_sas_debug_I_T_nexus_reset(), we call sas_phy_reset() to reset a
phy. But if the phy is disabled, sas_phy_reset() will directly return
-ENODEV without issue a phy reset request.
If so, We can directly return -ENODEV to libsas before issue a phy
reset.
Link: https://lore.kernel.org/r/1567774537-20003-4-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling sas_phy_reset(), we need to specify whether the reset type
is hard reset or link reset - use true/false for clarity.
Link: https://lore.kernel.org/r/1567774537-20003-3-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The event handler calls scsi_scan_host() when events are missed, which will
hotplug new LUNs. However, this function won't remove any unplugged LUNs.
The result is that hotunplug doesn't work properly when the number of
unplugged LUNs exceeds the event queue size (currently 8).
Scan existing LUNs when events are missed to check if they are still
present. If not, remove them.
Link: https://lore.kernel.org/r/20190905181903.29756-1-mlupfer@ddn.com
Signed-off-by: Matt Lupfer <mlupfer@ddn.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cdb in send_mode_select() is not zeroed and is only partially filled in
rdac_failover_get(), which leads to some random data getting to the
device. Users have reported storage responding to such commands with
INVALID FIELD IN CDB. Code before commit 3278255741 was not affected, as
it called blk_rq_set_block_pc().
Fix this by zeroing out the cdb first.
Identified & fix proposed by HPE.
Fixes: 3278255741 ("scsi_dh_rdac: switch to scsi_execute_req_flags()")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20190904155205.1666-1-martin.wilck@suse.com
Signed-off-by: Martin Wilck <mwilck@suse.com>
Acked-by: Ales Novak <alnovak@suse.cz>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In fcoe_if_init, if fc_attach_transport(&fcoe_vport_fc_functions)
fails, need to free the previously memory and return fail, otherwise
will trigger null-ptr-deref Read in fc_release_transport.
fcoe_exit
fcoe_if_exit
fc_release_transport(fcoe_vport_scsi_transport)
Link: https://lore.kernel.org/r/1566279789-58207-1-git-send-email-zhengbin13@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Link: https://lore.kernel.org/r/20190904130457.24744-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Link: https://lore.kernel.org/r/20190904130348.24772-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Link: https://lore.kernel.org/r/20190904130256.24704-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use kmemdup rather than duplicating its implementation
Link: https://lore.kernel.org/r/20190831124424.18642-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS_RESET pin on Qualcomm SoCs are controlled by TLMM and exposed
through the GPIO framework. Acquire the device-reset GPIO and use this to
implement the device_reset vops, to allow resetting the attached memory.
Based on downstream support implemented by Subhash Jadavani
<subhashj@codeaurora.org>.
Link: https://lore.kernel.org/r/20190828191756.24312-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS memory devices needs their reset line toggled in order to get them
into a good state for initialization. Provide a new vops to allow the
platform driver to implement this operation.
Link: https://lore.kernel.org/r/20190828191756.24312-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent patch unconditionally marks the hba as in error as part of
resetting the adapter. The driver flow that called the adapter reset was a
recovery path, which expects the adapter to not be in an error state in
order to finish the recovery. Given the new error state being set, the
recovery fails and the adapter is left in limbo.
Revise the adapter reset routine so that it will only mark the adapter in
error if it was unable to reset the adapter.
Fixes: 8c24a4f643 ("scsi: lpfc: Fix crash due to port reset racing vs adapter error handling")
Link: https://lore.kernel.org/r/20190903215441.10490-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert the remaining %pf users to %ps to prepare for the removal of the
old %pf conversion specifier support.
Fixes: 3235066449 ("scsi: lpfc: Migrate to %px and %pf in kernel print calls")
Link: https://lore.kernel.org/r/20190904160423.3865-1-sakari.ailus@linux.intel.com
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On fast cable pull, where driver is unable to detect device has disappeared
and came back based on switch info, qla2xxx would not re-login while remote
port has already invalidated the session. This causes IO timeout. This
patch would relogin to remote device for RSCN affected port.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-6-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Login session was stucked on cable pull. When FW is in the middle PRLI
PENDING + driver is in Initiator mode, driver fails to check back with FW to
see if the PRLI has completed. This patch would re-check with FW again to
make sure PRLI would complete before pushing forward with relogin.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-5-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
HINT_MBX_INT_PENDING is not guaranteed to be cleared by firmware. Remove
check that prevent driver load with ISP82XX.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-4-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use adapter specific callback to read flash instead of ISP adapter
specific.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-3-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch updates log message which indicates number of vectors used by
the driver instead of displaying failure to get maximum requested
vectors. Driver will always request maximum vectors during
initialization. In the event driver is not able to get maximum requested
vectors, it will adjust the allocated vectors. This is normal and does not
imply failure in driver.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Link: https://lore.kernel.org/r/20190830222402.23688-2-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For commands completing with a resid not aligned on the device logical
sector size, also print the command CDB in addition to the current message
to help debug hardware generating such incorrect command completion
information.
Link: https://lore.kernel.org/r/20190828053511.14818-1-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pci_alloc_irq_vectors() returns number of vectors allocated. Fix the check
for error condition.
Fixes: cca678dfba ("scsi: fnic: switch to pci_alloc_irq_vectors")
Link: https://lore.kernel.org/r/20190827211340.1095-1-gvaradar@cisco.com
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just a single lpfc fix adjusting the number of available queues for
high CPU count systems.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXXK/9iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUTCAP9C9a9W
sUBdDpe1bedPFJBBqT3540rucXGlSINXpm20RAEA7C9BkrHk7wFpCmieZscdDG2v
T5o0P6RYDEShcm91HLk=
=lrs3
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Just a single lpfc fix adjusting the number of available queues for
high CPU count systems"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Raise config max for lpfc_fcp_mq_threshold variable
Using the helper blk_queue_required_elevator_features(), set the
elevator feature ELEVATOR_F_ZBD_SEQ_WRITE as required for the request
queue of SCSI ZBC disks.
This feature requirement can always be satisfied as the mq-deadline
elevator is always selected for in-kernel compilation when
CONFIG_BLK_DEV_ZONED (zoned block device support) is enabled.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Port speed printing was added by commit d948e6383e ("scsi: fnic: Add port
speed stat to fnic debug stats"). As currently configured, this will cause
the port speed to be printed to syslog every 2 seconds. To prevent log
spamming, only print the vnic port speed at driver initialization and if
the speed changes. Also clean up a small typo in fnic_trace.c.
Fixes: d948e6383e ("scsi: fnic: Add port speed stat to fnic debug stats")
Signed-off-by: John Pittman <jpittman@redhat.com>
Reviewed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_process_unsol_compl:
drivers/scsi/bnx2fc/bnx2fc_hwi.c:636:30: warning: variable task set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_process_ofld_cmpl:
drivers/scsi/bnx2fc/bnx2fc_hwi.c:1125:21: warning: variable port set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_init_seq_cleanup_task:
drivers/scsi/bnx2fc/bnx2fc_hwi.c:1468:30: warning: variable orig_task set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_initiate_seq_cleanup:
drivers/scsi/bnx2fc/bnx2fc_io.c:932:19: warning: variable lport set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_initiate_cleanup:
drivers/scsi/bnx2fc/bnx2fc_io.c:1001:19: warning: variable lport set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_process_scsi_cmd_compl:
drivers/scsi/bnx2fc/bnx2fc_io.c:1882:20: warning: variable host set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c: In function bnx2fc_rcv:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:431:26: warning: variable fh set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 8.42.3.0.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a race b/w fipvlan request and response path:
=====
qedf_fcoe_process_vlan_resp:113]:2: VLAN response, vid=0xffd.
qedf_initiate_fipvlan_req:165]:2: vlan = 0x6ffd already set.
qedf_set_vlan_id:139]:2: Setting vlan_id=0ffd prio=3.
======
The request thread sees that vlan is already set and fails to call
ctrl_link_up.
Fix:
- While setting vlan_id use local variable and before setting vlan_id.
- Call fcoe_ctlr_link_up in next iteration of fipvlan request.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The list of rports might become stale so we should rather traverse the
discovery list when trying relogin.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent race where we're removing the module and we get link update
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Problem Statement:
- Driver has fc_id of 0xcc0200
- Driver gets link down (due to test) and calls fcoe_ctlr_link_down().
- At this point, the fc_id of the initiator port is zeroed out.
- Driver gets a link up 14 seconds later.
- Driver performs FIP VLAN request, gets a response from the switch.
- No change in VLAN is detected.
- Driver then notifies libfcoe via fcoe_ctlr_link_up().
- Libfcoe then issues a multicast discovery solicitation as expected.
- Cisco FCF responds to that correctly.
- Libfcoe at this point starts a 3 sec count-down to allow any other FCFs
to be discovered. However, at this point, it has been 20 seconds since
the last FKA from the driver (which would have been sent prior to
backlink toggle), which causes the CVL to be issued from Cisco CVL from
the switch is dropped by the driver as the vx_port identification
descriptor is present and has value of 0xcc0200, which does not match
the driver's value of 0. Libfcoe completes the 3 sec count down and
proceeds to issue FLOGI as per protocol. Switch rejects FLogi request.
All subsequent FLOGI requests from libfc are rejected by the switch
(possibly because it is now expecting a new solicitation). This
situation will continue until the next link toggle.
Solution:
The Vx_port descriptor in the CVL has three fields:
MAC address
Fabric ID
Port Name
Today, the code checks for both #1 and #2 above. In the case where we went
through a link down, both these will be zero until FLOGI succeeds.
We should change our code to check if any one of these 3 is valid and if
so, handle the CVL (basically switching from AND to OR). The port name
field is definitely expected to be valid always.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Log s_id, d_id, type and command to the log message.
[mkp: fixed warning]
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current code doeesn't support 20Gbps speed for current and supported
speed. Add support for it.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was wrongly interpreting the supported cap value returned by qed.
Solution: Use QED define macros instead of OS defined for interpreting
supporting speeds.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was attempting to print cdb[0], which is not set for resets coming
from SCSI ioctls. Check for cmd_len before accessing cmnd.
Crash info:
[84790.864747] BUG: unable to handle kernel NULL pointer dereference at (null)
[84790.864783] IP: qedf_initiate_tmf+0x7a/0x6e0 [qedf]
[84790.865204] Call Trace:
[84790.865246] scsi_try_target_reset+0x2b/0x90 [scsi_mod]
[84790.865266] scsi_ioctl_reset+0x20f/0x2a0 [scsi_mod]
[84790.865284] scsi_ioctl+0x131/0x3a0 [scsi_mod]
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- On some setups fipvlan can be retried for long duration and the
connection to switch was not there so it was not getting any reply.
- During unload this thread was hanging.
Problem Resolution:
Check if unload is in progress, then quit from fipvlan thread.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print messages during exiting condition to help debugging.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add:
PM8222 VID_9005, DID_028F, SVID_1BD4 and SDID_004F
3101E-4i (1G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0808
3102E-8i (2G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0809
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return -EINPROGRESS when a rescan worker is queued.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When each ld is deleted, a rescan event is triggered in the driver. These
can stack up waiting on mutex_lock.
Change to mutex_try_lock and schedule a rescan for later.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return identify physical device "Phys_Bay_in_Box" as bay_identifier.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- serial number
- model
- vendor
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Expose physical devices before logical devices.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 12.4.0.0 patch that merged WQ/CQ pairs into single per-cpu pair
contained a bug: a local variable was set to the queue pair by index. This
should have allowed the local variable to be natively used. Instead, the
code reused the index relative to the local variable, obtaining a random
pointer value that when used eventually faulted the system
Convert offending code to use local variable.
Fixes: c00f62e6c5 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Raise the config max for lpfc_fcp_mq_threshold variable to 256.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Capturing and downloading dif command data and dif data was done a dozen
years ago and no longer being used. Also creates a potential security hole.
Remove the debugfs buffer for dif debugging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: KyleMahlkuch <kmahlkuc@linux.vnet.ibm.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Per Dan Carpenter:
The patch d79c9e9d4b: "scsi: lpfc: Support dynamic unbounded SGL lists on
G7 hardware." from Aug 14, 2019, leads to the following static checker
warning:
drivers/scsi/lpfc/lpfc_init.c:4107 lpfc_new_io_buf()
error: not allocating enough data 784 vs 768
There was no need to compare sizes nor to allocate size based on a define.
Change allocation to use actual structure length
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/ufs/ufs-qcom.c: In function ufs_qcom_pwr_change_notify:
drivers/scsi/ufs/ufs-qcom.c:808:6: warning: variable val set but not used [-Wunused-but-set-variable]
Fixes: 1e1e465c6d ("scsi/ufs: qcom: Remove ufs_qcom_phy_*() calls from host")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in a ql_log message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c: In function cq_interrupt_v1_hw:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:1542:6: warning: variable irq_value set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides a module parameter and sysfs interface to select
whether the queue depth for each device should be based on the
protocol-specific value set by the driver (the default) or the maximum
supported by the controller (can_queue).
Although we have a sysfs interface per sdev to change the queue depth
of individual scsi devices, this implementation provides a single
sysfs entry per shost to switch between the controller max and the
driver default.
[mkp: tweaked commit desc]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the firmware documentation a status type 0 IOCB can be
followed by one or more status continuation type 0 IOCBs. Hence do not
complain if the completion function is not called from inside the status
type 0 IOCB handler.
WARNING: CPU: 10 PID: 425 at drivers/scsi/qla2xxx/qla_isr.c:2784
qla2x00_status_entry.isra.7+0x484/0x17b0 [qla2xxx]
CPU: 10 PID: 425 Comm: kworker/10:1 Tainted: G E 5.3.0-rc4-next-20190813-autotest-autotest #1
Workqueue: qla2xxx_wq qla25xx_free_rsp_que [qla2xxx]
Call Trace:
qla2x00_status_entry.isra.7+0x1484/0x17b0 [qla2xxx] (unreliable)
qla24xx_process_response_queue+0x7d8/0xbd0 [qla2xxx]
qla25xx_free_rsp_que+0x1a0/0x220 [qla2xxx]
process_one_work+0x25c/0x520
worker_thread+0x8c/0x5e0
kthread+0x154/0x1a0
ret_from_kernel_thread+0x5c/0x7c
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently bits in hba->outstanding_tasks are cleared only after their
corresponding task management commands are successfully done by
__ufshcd_issue_tm_cmd().
If timeout happens in a task management command, its corresponding bit in
hba->outstanding_tasks will not be cleared until next task management
command with the same tag used successfully finishes.
This is wrong and can lead to some issues, like power issue. For example,
ufshcd_release() and ufshcd_gate_work() will do nothing if
hba->outstanding_tasks is not zero even if both UFS host and devices are
actually idle.
Solution is referred from error handling of device commands: bits in
hba->outstanding_tasks shall be cleared regardless of their execution
results.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pointer fh is being assigned a return value from the call to
skb_transport_header however this value is never read and fh is being
re-assigned immediately afterwards with a new value. Since there are
side-effects from calling skb_transport_header the call is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices have issues if LCC is enabled. So we are setting
PA_LOCAL_TX_LCC_Enable to 0 before link startup which will make sure that
both host and device TX LCC are disabled once link startup is completed.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable error is being initialized with a value that is never read and
error is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Four fixes, three for edge conditions which don't occur very often.
The lpfc fix mitigates memory exhaustion for some high CPU systems.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXWEBrCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishds+AQCyQlgV
TzSFQ1zvbAb3SNFdNsCzzb8Aq2vJC+RojF2VFgD/cJfE2fix9E7Nk8PCGwH1sgnf
m5Glsvv8BEmmtoikrb8=
=Ti6g
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four fixes, three for edge conditions which don't occur very often.
The lpfc fix mitigates memory exhaustion for some high CPU systems"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Mitigate high memory pre-allocation by SCSI-MQ
scsi: ufs: Fix NULL pointer dereference in ufshcd_config_vreg_hpm()
scsi: target: tcmu: avoid use-after-free after command timeout
scsi: qla2xxx: Fix gnl.l memory leak on adapter init failure
Hi Linus,
Please, pull the following patches that mark switch cases where we are
expecting to fall through.
- Fix fall-through warnings on arm and mips for multiple
configurations.
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEkmRahXBSurMIg1YvRwW0y0cG2zEFAl1clmEACgkQRwW0y0cG
2zGqbg/9HPC3Cf3oYq4o0/kV+cfS0ir6iJCz1mspFfbBloaS/EU7A2CF35bDz7k3
XUzl/ci82EQCnuJv/X6ddayUF1S/vFWLnQXRznz07kJspUnNpu7JKgsZr2qsHaRe
CfCj62J/Kuhnke8EUjuWEuga6YXYsYlcevgg/tpVXsTmxrpq2A15tWyut7WEe4JQ
kWPELwYbPsDvTj2siZrgMRBx4gVzQKQVo5TpZiuADeJu9RuFT/64PI9TDQGE7c+X
fFq4ijd1YPj/E+WI7k5VdUbXYiPIIXmkJ4VAPcu5VWmUS7y7bTeye0Jc3uYAxI1r
7rykYhNzniGn3SZL+wq8rHchL3dTLBYhd34HhTlb5xdGFwmbzKgHBqdlGpH8HOo+
CLu8kPYdmnzYCth4md0ENwgBVkj0tweyZuMzCys1qR6RFhOipxWLNGEvIXWZ0Sp8
uNyXnPdCrZTmlwubwY4FOOLsGKW06GnD64cfmEYoCMcmT2j7clbjasWYM4PXQvbt
0dVtt8k4M5LJBLh8qTX7RMZHDQYMiiYiMnLLAXf4wB0VUTqgNuLc4k0PpX3kBYtO
4b0lU/LQH+8811BMNVBHK55StQ8DjM0C2yfQWx610eoohjV70JTyxOWoqeHFL5hq
DIFdLDOgvJCqtyYgJDjmCmH9x6lgfvmxAKq66h9Z7vt25KLUizQ=
=fQZm
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull more fallthrough fixes from Gustavo A. R. Silva:
"Fix fall-through warnings on arm and mips for multiple configurations"
* tag 'Wimplicit-fallthrough-5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
video: fbdev: acornfb: Mark expected switch fall-through
scsi: libsas: sas_discover: Mark expected switch fall-through
MIPS: Octeon: Mark expected switch fall-through
power: supply: ab8500_charger: Mark expected switch fall-through
watchdog: wdt285: Mark expected switch fall-through
mtd: sa1100: Mark expected switch fall-through
drm/sun4i: tcon: Mark expected switch fall-through
drm/sun4i: sun6i_mipi_dsi: Mark expected switch fall-through
ARM: riscpc: Mark expected switch fall-through
dmaengine: fsldma: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: mtx1_defconfig mips):
drivers/scsi/libsas/sas_discover.c: In function ‘sas_discover_domain’:
./include/linux/printk.h:309:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_NOTICE pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/libsas/sas_discover.c:459:3: note: in expansion of macro ‘pr_notice’
pr_notice("ATA device seen but CONFIG_SCSI_SAS_ATA=N so cannot attach\n");
^~~~~~~~~
drivers/scsi/libsas/sas_discover.c:462:2: note: here
default:
^~~~~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Update lpfc version to 12.4.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, each hardware queue, typically allocated per-cpu, consists of a
WQ/CQ pair per protocol. Meaning if both SCSI and NVMe are supported 2
WQ/CQ pairs will exist for the hardware queue. Separate queues are
unnecessary. The current implementation wastes memory backing the 2nd set
of queues, and the use of double the SLI-4 WQ/CQ's means less hardware
queues can be supported which means there may not always be enough to have
a pair per cpu. If there is only 1 pair per cpu, more cpu's may get their
own WQ/CQ.
Rework the implementation to use a single WQ/CQ pair by both protocols.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FC-NVMe-2 added support for sequence level error recovery in the FC-NVME
protocol. This allows for the detection of errors and lost frames and
immediate retransmission of data to avoid exchange termination, which
escalates into NVMeoFC connection and association failures. A significant
RAS improvement.
The driver is modified to indicate support for SLER in the NVMe PRLI is
issues and to check for support in the PRLI response. When both sides
support it, the driver will set a bit in the WQE to enable the recovery
behavior on the exchange. The adapter will take care of all detection and
retransmission.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Typical SLI-4 hardware supports up to 2 4KB pages to be registered per XRI
to contain the exchanges Scatter/Gather List. This caps the number of SGL
elements that can be in the SGL. There are not extensions to extend the
list out of the 2 pages.
The G7 hardware adds a SGE type that allows the SGL to be vectored to a
different scatter/gather list segment. And that segment can contain a SGE
to go to another segment and so on. The initial segment must still be
pre-registered for the XRI, but it can be a much smaller amount (256Bytes)
as it can now be dynamically grown. This much smaller allocation can
handle the SG list for most normal I/O, and the dynamic aspect allows it to
support many MB's if needed.
The implementation creates a pool which contains "segments" and which is
initially sized to hold the initial small segment per xri. If an I/O
requires additional segments, they are allocated from the pool. If the
pool has no more segments, the pool is grown based on what is now
needed. After the I/O completes, the additional segments are returned to
the pool for use by other I/Os. Once allocated, the additional segments are
not released under the assumption of "if needed once, it will be needed
again". Pools are kept on a per-hardware queue basis, which is typically
1:1 per cpu, but may be shared by multiple cpus.
The switch to the smaller initial allocation significantly reduces the
memory footprint of the driver (which only grows if large ios are
issued). Based on the several K of XRIs for the adapter, the 8KB->256B
reduction can conserve 32MBs or more.
It has been observed with per-cpu resource pools that allocating a resource
on CPU A, may be put back on CPU B. While the get routines are distributed
evenly, only a limited subset of CPUs may be handling the put routines.
This can put a strain on the lpfc_put_cmd_rsp_buf_per_cpu routine because
all the resources are being put on a limited subset of CPUs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added code to support driver loopback with MDS Diagnostics. This style of
diagnostics passes frames from the fabric to the driver who then echo them
back out the link. SEND_FRAME WQEs are used to transmit the frames. Added
the SOF and EOF field location definitions for use by SEND_FRAME.
Also ensure that enable_mds_diags is a RW parameter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To aid better hardware detection when there are issues, report the first
and second level hardware revisions from the READ_REV command. Add the
elements to the existing hardware id string.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to see real addresses, convert %p with %px for kernel addresses
and replace %p with %pf for functions.
While converting, standardize on "x%px" throughout (not %px or 0x%px).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While performing code review, several relatively simple optimizations can
be done in the fast path.
Add these optimizations (unlikely designators).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Running on Coverity produced the following errors:
- coding style (indentation)
- memset size mismatch errors
note: comment cases where it is purposely a mismatch
Fix the errors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
modinfo for lpfc_nvme_enable_fb is incorrect. FirstBurst on lpfc target is
not fully supported.
Update the attribute description
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is allowing the user to change lpfc_enable_bg while loading the
driver against a FCoE adapter. This is not supported.
No check is made for the adapter type when applying the blockguard
enablement value.
Fix by verifying the adapter type before setting the enablement flag.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
GetTrunkInfo is displaying an incorrect link speed when the link is a trunk
and the link has gone down. The driver is not clearing the logical speed
as part of the link down transition.
Fix by setting the logical speed to UNKNOWN SPEED when the link goes down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Max Frame Size value is shown as 34816 in fdmishow from Switch.
The driver uses bbRcvSize in common service param which is obtained from
the READ_SPARM mailbox command. The bbRcvSize field which is displayed is a
three nibble field but the driver is printing a full four nibbles.
Fix by masking off the upper nibble.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The scsi transport fc bsg interface does not expect the bsg_job_done()
callback to be done if the bsg request call returns failure. Several of the
HST_VENDOR cases in the driver unconditionally call bsg_job_done()
regardless of the returning value.
Fix the code to only call bsg_job_done() if the call to lpfc_bsg_request()
will return success.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When forcing the use of MSI (vs MSI-X) the driver is crashing in
pci_irq_get_affinity.
The driver was not using the new pci_alloc_irq_vectors interface in the MSI
path.
Fix by using pci_alloc_irq_vectors() with PCI_RQ_MSI in the MSI path.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently reporting a non-zero nvme sg_seg_cnt value of 256
when nvme is disabled. It should be zero.
Fix by ensuring the value is cleared.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an unsolicited ABTS was received, the driver looks up the exchange it
references. It it does various searches looking for the exchange
context. When one is eventually matched and it is associated with an XRI
context, the driver sends an ABORT WQE to terminate the exchange. Current
code looks at whether the transport had taken action on the XRI yet or not
(no action if set to LPFC_NVMET_STE_RCV; action if non-LPFC_NVMET_STE_RCV).
Based on action or not one of two (sol vs unsol) issue abort routines are
called. The unsol version cheats and transmits a sequence containing an
ABTS with no interaction with the adapter. The sol version issues an Abort
WQE and lets the adapter manage whether the ABTS is sent to not.
The issue is the unsol version is sending ABTS unconditionally for the
exchange that received the ABTS. It's unnecessary.
Remove the conditional and just call the adapter command-based routine to
let the adapter manage the ABTS.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of firmware download, the adapter is reset. On the adapter the
reset causes the function to stop and all outstanding io is terminated
(without responses). The reset path then starts teardown of the adapter,
starting with deregistration of the remote ports with the nvme-fc
transport. The local port is then deregistered and the driver waits for
local port deregistration. This never finishes.
The remote port deregistrations terminated the nvme controllers, causing
them to send aborts for all the outstanding io. The aborts were serviced in
the driver, but stalled due to its state. The nvme layer then stops to
reclaim it's outstanding io before continuing. The io must be returned
before the reset on the controller is deemed complete and the controller
delete performed. The remote port deregistration won't complete until all
the controllers are terminated. And the local port deregistration won't
complete until all controllers and remote ports are terminated. Thus things
hang.
The issue is the reset which stopped the adapter also stopped all the
responses that would drive i/o completions, and the aborts were also
stopped that stopped i/o completions. The driver, when resetting the
adapter like this, needs to be generating the completions as part of the
adapter reset so that I/O complete (in error), and any aborts are not
queued.
Fix by adding flush routines whenever the adapter port has been reset or
discovered in error. The flush routines will generate the completions for
the scsi and nvme outstanding io. The abort ios, if waiting, will be caught
and flushed as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This issue is specific to SLI-3 adapters, specifically when DIF is used.
Once seen, this message floods the logs:
9064 BLKGRD: lpfc_scsi_prep_dma_buf_s3: Too many sg segments from
dma_map_sg
The driver, upon detecting an error such as too many elements in an sglist,
misrepresents the error by treating it as a temporary resource issue by
returning MLQUEUE_HOST_BUSY. In these cases, no retry will fix it and it
should have been a hard error. The repeated retry was causing the spamming
of the log.
As for the initial reason of why an I/O encountered this issue at all is
not clear as parameters set by the driver should have avoided this. The
dm multipath maintainer has been notified of the issue.
Fix by changing the return code for the dma mapping routines to indicate
cases that are not retryable and return DID_ERROR on those cases.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter encounters a condition which causes the adapter to fail
(driver must detect the failure) simultaneously to a request to the driver
to reset the adapter (such as a host_reset), the reset path will be racing
with the asynchronously-detect adapter failure path. In the failing
situation, one path has started to tear down the adapter data structures
(io_wq's) while the other path has initiated a repeat of the teardown and
is in the lpfc_sli_flush_xxx_rings path and attempting to access the
just-freed data structures.
Fix by the following:
- In cases where an adapter failure is detected, rather than explicitly
calling offline_eratt() to start the teardown, change the adapter state
and let the later calls of posted work to the slowpath thread invoke the
adapter recovery. In essence, this means all requests to reset are
serialized on the slowpath thread.
- Clean up the routine that restarts the adapter. If there is a failure
from brdreset, don't immediately error and leave things in a partial
state. Instead, ensure the adapter state is set and finish the teardown
of structures before returning.
- If in the scsi host reset handler and the board fails to reset and
restart (which can be due to parallel reset/recovery paths), instead of
hard failing and explicitly calling offline_eratt() (which gets into the
redundant path), just fail out and let the asynchronous path resolve the
adapter state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During cable pull testing a deadlock was seen between lpfc_nlp_counters()
vs lpfc_mbox_process_link_up() vs lpfc_work_list_done(). They are all
waiting on the shost->host_lock.
Issue is all of these cases raise irq when taking out the lock but use
spin_unlock_irq() when unlocking. The unlock path is will unconditionally
re-enable interrupts in cases where irq state should be preserved. The
re-enablement allowed the other paths to execute which then causes the
deadlock.
Fix by converting the lock/unlock to irqsave/irqrestore.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a test with high nvme remote port counts connected via a multi-hop FC
switch config where switches were systematically reset (e.g. fabric
partitioning and re-establishment), the nvme remote ports would switch
addresses based on the switch reconfiguration events. The driver would get
into a situation where the nvme port changed address, PLOGI and PRLI would
succeed nvme transport registration occurred, but subsequent LS requests by
the nvme subsystem failed due to a bad ndlp state and connectivity to the
device failed.
The driver hit a race condition on multiple devices that address swapped
simultaneously. In cases where the driver notices the remote port structure
came back as the same value as previously (meaning a nvme_rport structure
was re-enabled and did not go through devloss_tmo/connect_tmo_failures on
all controllers) the driver would unconditionally exit assuming the ndlp
information was correct. But, if the ndlp's had been swapped, the ndlp had
stale port state information, which when used by the LS request commands,
would fail the commands.
Fix by checking whether a node swap had occurred, and only exit if no ndlp
swap had occurred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In situations where zoning is not being used, thus NVMe initiators see
other NVMe initiators as well as NVMe targets, a link bounce on an
initiator will cause the NVMe initiators to spew "6169" State Error
messages.
The driver is not qualifying whether the remote port is a NVMe targer or
not before calling the lpfc_nvme_rescan_port(), which validates the role
and prints the message if its only an NVMe initiator.
Fix by the following:
- Before calling lpfc_nvme_rescan_port() ensure that the node is a NVMe
storage target or a NVMe discovery controller.
- Clean up implementation of lpfc_nvme_rescan_port. remoteport pointer
will always be NULL if a NVMe initiator only. But, grabbing of
remoteport pointer should be done under lock to coincide with the
registering of the remote port with the fc transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On an SLI-3 adapter which does not support NVMe, but with the driver global
attribute to enable nvme on any adapter if it does support NVMe
(e.g. module parameter lpfc_enable_fc4_type=3), the SGL and total SGE
values are being munged by the protocol enablement when it shouldn't be.
Correct by changing the location of where the NVME sgl information is being
applied, which will avoid any SLI-3-based adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If admin changes the devloss_tmo on an rport via the fc_remote_port rport
dev_loss_tmo attribute, the value is on set on scsi stack. The change is
not propagated to NVMe.
The set routine in the lldd lacks the call to
nvme_fc_set_remoteport_devloss() to set the value.
Fix by adding the call to the lldd set routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In tests with remote ports contantly logging out/logging coupled with
occassional local link bounce, if a remote port is disocnnected for longer
than devloss_tmo and then subsequently reconnected, eventually the test
will fail to login with the remote port and remote port connectivity is
lost.
When devloss_tmo expires, the driver does not free the node struct until
the port or npiv instances is being deleted. The node is left allocated but
the state set to UNUSED. If the node was in the process of logging in when
the local link drop occurred, meaning the RPI was allocated for the node in
order to send the ELS, but not yet registered which comes after successful
login, the node is moved to the NPR state, and if devloss expires, to
UNUSED state. If the remote port comes back, the node associated with it
is restarted and this path happens to allocate a new RPI and overwrites the
prior RPI value. In the cases where the port was logged in and loggs out,
the path did release the RPI but did not set the node rpi value. In the
cases where the remote port never finished logging in, the path never did
the call to release the rpi. In this latter case, when the node is
subsequently restore, the new rpi allocation overwrites the rpi that was
not released, and the rpi is now leaked. Eventually the port will run out
of RPI resources to log into new remote ports.
Fix by following changes:
- When an rpi is released, do so under locks and ensure the node rpi value
is set to a non-allocated value (LPFC_RPI_ALLOC_ERROR). Note:
refactored to a small service routine to avoid indentation issues.
- When re-enabling a node, check the rpi value to determine if a new
allocation is necessary. If already set, use the prior rpi.
Enhanced logging to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a remote port is removed and remains removed for devloss_tmo, if an RSCN
is subsequently received indicating the presence of the remte port, the
driver does not login to and rediscovery the remote port.
Currently, in order to for a port to be rediscovered post an RSCN, the node
state must be NPR to reflect not logged in. When devloss expires, the node
state is marked UNUSED. When an RSCN occurs, the nodes referenced by the
RSCN will have a NPR_2B_DISC flag set, but the re-login will only be
attempted if the node is in NPR_NODE state. Thus the node is skipped over.
Fix by recognizing the NPR_2B_DISC and UNUSED and transition the node back
to NPR state to allow the re-login to take place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an admin updates lpfc's devloss_tmo sysfs attribute, the kernel will
oops.
Coding of a loop allowed a new value (rport) to be set/checked for null
followed by an older value (remoteport) checked for null to allow progress
where the new value, even though null, will be referenced.
Rework the logic to validate and prevent any reference to the null ptr.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the driver to initiate an FLOGI and before it completes,
another link down/up transition occurs requiring a new FLOGI. Currently,
nothing is done to abort/noop the older FLOGI request to the adapter, so if
this transition occurs and the FLOGI completion is received after the link
down/up transition, the driver may erroneously act on the older FLOGI. In
most cases, the adapter properly terminates/fails the FLOGI, but there is a
timing condition where the FLOGI may complete on the wire prior to the
transition, but the response may not be seen/processed by the driver before
the driver sees the link transition.
Fix by having the link down handler in the driver run through any
outstanding ELS's and change the completion handler of the ELS so that it
will be no-op'd and released.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When tearing down the adapter for a reset, online/offline, or driver
unload, the queue free routine would hit a GPF oops. This only occurs on
conditions where the number of hardware queues created is fewer than the
number of cpus in the system. In this condition cpus share a hardware
queue. And of course, it's the 2nd cpu that shares a hardware that
attempted to free it a second time and hit the oops.
Fix by reworking the cpu to hardware queue mapping such that:
Assignment of hardware queues to cpus occur in two passes:
first pass: is first time assignment of a hardware queue to a cpu.
This will set the LPFC_CPU_FIRST_IRQ flag for the cpu.
second pass: for cpus that did not get a hardware queue they will
be assigned one from a primary cpu (one set in first pass).
Deletion of hardware queues is driven by cpu itteration, and queues
will only be deleted if the LPFC_CPU_FIRST_IRQ flag is set.
Also contains a few small cleanup fixes and a little better logging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter reset path (lpfc_sli_hba_down) is taking/releasing a lock with
irq. But, the path is already under the hbalock which raised irq so it's
unnecessary.
Convert to simple lock/unlock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvme_register_port hit a null prev_ndlp pointer in a test with lots of
target ports swapping addresses. The oldport value was stale, thus it's
ndlp (prev_ndlp set to it) was used.
Fix by moving oldrport pointer checks, and if used prev_ndlp pointer
assignment, to be done while the lock is held.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is inadvertently trying to issue an INIT_VPI mailbox command on
an SLI-3 driver. The command is specific to SLI-4. When the call is made to
send the command, if on an SLI-3 adapter, an array pointer is NULL and the
driver will oops.
Fix by restricting the command to SLI-4 adapters only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target issues an ADISC to the port and the target is a NVME target,
the driver is inadvertantly invalidating the login and marking the remote
port as logged out. Communication with the target is lost.
Revise the ADISC check so that FCP or NVME targets will be marked valid at
the end of ADISC processing. Enhance logging to recognize condition
better.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some remote ports may be slow in registering their GID_FT protocol
information with the fabric. If the remote port is an initiator, it may
send PLOGI to the port before the GID_FT logic is complete. Meaning, after
accepting the PLOGI, when the driver may see no response to the GID_FT that
is issued after the login to determine the protocols supported so that
proper PRLI's may be transmit. If the driver has no fc4 information, it
currently stops and the remote port is not discovered.
Fix by issuing a LOGO when there is no GID_FT information. The LOGO
completion handling will attempt to re-login if the nport_id is still
present.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In cases of remote-port-side cable pull/replug, there happens to be a
target that upon replug will send the port a PLOGI, a PRLI, and a LOGO.
When this sequence is received by the driver, the PLOGI accepted and a
GFT_ID is issued to find the protocol support for the remote port. While
the GFT_ID is outstanding, a LOGO is received. The driver logs the remote
port out and unregisters the RPI and schedules a new PLOGI transmission.
However, the GFT_ID was not terminated. When it completed, the driver
attempted to transition the remote port to PRLI transmission, which cancels
the PLOGI scheduling. The PRLI transmit attempt is rejected by the adapter
as the remote port is not logged in. No retry is attempted as it's expected
the logout is noted and the supposedly scheduled PLOGI should address the
state. As there is no PLOGI, the remote port does not get re-discovered.
Fix by aborting the outstanding GFT_ID if the related remote port is logged
out.
Ensure a PRLI transmit attempt only occurs if the remote port is logging
in. This avoids the incorrect attempt while logged out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter is reset while there are outstanding ELS's, subsequent
reinitialization of the adapter will fail as it has not recovered all of
the io contexts relative to the ELS's.
If an ELS timed out or otherwise failed and an the ELS was attempted to be
aborted (which changes the ELS completion context), in causes where the
driver generates completions for the outstanding IO as the adapter would
not due to being reset, the driver released only the ELS context and failed
to release the abort context. When the adapter went to reinit, as it had
not received all of the contexts, it failed to reinit.
Fix by having the ELS completion handler identify the driver-generated
completion status and release the abort context.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unusually high IO latency can be observed with little IO in progress. The
latency may remain high regardless of amount of IO and can only be cleared
by forcing lpfc_fcp_imax values to non-zero and then back to zero.
The driver's eq_delay mechanism that scales the interrupt coalescing based
on io completion load failed to reduce or turn off coalescing when load
decreased. Specifically, if no io completed on a cpu within an eq_delay
polling window, the eq delay processing was skipped and no change was made
to the coalescing values. This left the coalescing values set when they
were no longer applicable.
Fix by always clearing the percpu counters for each time period and always
run the eq_delay calculations if an eq has a non-zero coalescing value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a timer routine uses workqueues, it could fire before the workqueue is
allocated.
Fix by allocating the workqueue before the timer routines are setup
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After seeing some interoperability issues with ADISC, it was determined the
ELS definitions in lpfc were using types that allowed the compiler to add
pad to the structure, causing the structure to no longer be per spec. The
offending structures are ADISC, FAN, and RNID.
This patch implements the simple fix of eliminating the pad by forcing the
compiler to pack the structure. Care was taken to ensure field accesses
won't be by operations that would hit a bad field alignment.
The better solution would be to convert to the uapi fc header definitions,
but the number of changes required to do is rather intrusive so this course
of action was deferred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connected to a high number of remote ports, the driver is encountering
PLOGI errors. The errors are due to adapter detected failures indicating
illegal field values.
Turns out the driver was prematurely clearing an RPI bitmask before waiting
for an UNREG_RPI mailbox completion. This allowed the RPI to be reused
before it was actually available.
Fix by clearing RPI bitmask only after UNREG_RPI mailbox completion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi-mq operation inherently performs pre-allocation of resources for
blk-mq request queues. Even though the kdump environment reduces the
configuration to a single CPU, thus 1 hardware queue, which helps
significantly, the resources are still rather large due to the per request
allocations. blk-mq pre-allocations can be over 4KB per request. With
adapter can_queue values in the 4k or 8k range, this can easily be 32MBs
before any other driver memory is factored in. Driver SGL DMA buffer
allocation can be up to 8KB per request as well adding an additional
64MB. Totals are well over 100MB for a single shost. Given kdump memory
auto-sizing utilities don't accommodate this amount of memory well, it's
very possible for kdump to fail due to lack of memory.
Fix by having the driver recognize that it is booting within a kdump
context and reduce the number of requests it will support to a more
reasonable value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As dma_pool_destroy and mempool_destroy functions has NULL check. We may
not need NULL check before calling them.
Fix below warnings reported by coccicheck
./drivers/scsi/lpfc/lpfc_mem.c:252:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:255:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:258:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:261:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:265:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:269:2-17: WARNING: NULL check before some
freeing functions is not needed.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Static structure ufs_hba_qcom_vops, of type ufs_hba_variant_ops, is used
only once, when it is passed as the second argument to function
ufshcd_pltfrm_init(). In the definition of ufshcd_pltfrm_init(), its second
parameter (corresponding to ufs_hba_qcom_vops) is declared as
constant. Hence declare ufs_hba_qcom_vops itself constant as well to
protect it from unintended modification. Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SCSI-MQ is enabled, the SCSI-MQ layers will do pre-allocation of MQ
resources based on shost values set by the driver. In newer cases of the
driver, which attempts to set nr_hw_queues to the cpu count, the
multipliers become excessive, with a single shost having SCSI-MQ
pre-allocation reaching into the multiple GBytes range. NPIV, which
creates additional shosts, only multiply this overhead. On lower-memory
systems, this can exhaust system memory very quickly, resulting in a system
crash or failures in the driver or elsewhere due to low memory conditions.
After testing several scenarios, the situation can be mitigated by limiting
the value set in shost->nr_hw_queues to 4. Although the shost values were
changed, the driver still had per-cpu hardware queues of its own that
allowed parallelization per-cpu. Testing revealed that even with the
smallish number for nr_hw_queues for SCSI-MQ, performance levels remained
near maximum with the within-driver affiinitization.
A module parameter was created to allow the value set for the nr_hw_queues
to be tunable.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As spin_unlock_irq will enable interrupts.
Function lpfc_findnode_rpi is called from
lpfc_sli_abts_err_handler (./drivers/scsi/lpfc/lpfc_sli.c)
<- lpfc_sli_async_event_handler
<- lpfc_sli_process_unsol_iocb
<- lpfc_sli_handle_fast_ring_event
<- lpfc_sli_fp_intr_handler
<- lpfc_sli_intr_handler
and lpfc_sli_intr_handler is an interrupt handler.
Interrupts are enabled in interrupt handler. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq in
IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the redundant initialization code.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable ret is initialized to a value that is never read and it is
re-assigned later and immediately returns. Clean up the code by removing
rc and just returning 0.
[mkp: typo]
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid code duplication between qla2x00_alloc_offload_mem() and
qla2x00_alloc_fw_dump() by moving the FCE and EFT buffer allocation and
initialization to separate functions. Cleanly track failure and success by
making sure that the ha->eft, ha->fce and respective eft_dma, fce_dma
members are set if and only if the buffers are properly allocated and
initialized. Avoid pointless buffer reallocation. Eliminate some goto
statements. Make sure the fce_enabled flag is cleared when the FCE buffer
is freed.
Fixes: ad0a0b01f0 ("scsi: qla2xxx: Fix Firmware dump size for Extended login and Exchange Offload")
Fixes: a28d9e4ef9 ("scsi: qla2xxx: Add support for multiple fwdump templates/segments")
Cc: Joe Carnuccio <joe.carnuccio@cavium.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In qla2x00_alloc_fw_dump(), an existing EFT buffer (e.g. from previous
invocation of qla2x00_alloc_offload_mem()) is freed. The buffer is then
re-allocated, but without setting the eft and eft_dma fields to the new
values.
Fixes: a28d9e4ef9 ("scsi: qla2xxx: Add support for multiple fwdump templates/segments")
Cc: Joe Carnuccio <joe.carnuccio@cavium.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SGI SN2 support is about to be removed, so drop the bits specific to
it from this driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-13-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SGI SN2 support is about to be removed, so drop the bits specific to
it from this driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-12-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the following BUG:
[ 187.065689] BUG: kernel NULL pointer dereference, address: 000000000000001c
[ 187.065790] RIP: 0010:ufshcd_vreg_set_hpm+0x3c/0x110 [ufshcd_core]
[ 187.065938] Call Trace:
[ 187.065959] ufshcd_resume+0x72/0x290 [ufshcd_core]
[ 187.065980] ufshcd_system_resume+0x54/0x140 [ufshcd_core]
[ 187.065993] ? pci_pm_restore+0xb0/0xb0
[ 187.066005] ufshcd_pci_resume+0x15/0x20 [ufshcd_pci]
[ 187.066017] pci_pm_thaw+0x4c/0x90
[ 187.066030] dpm_run_callback+0x5b/0x150
[ 187.066043] device_resume+0x11b/0x220
Voltage regulators are optional, so functions must check they exist
before dereferencing.
Note this issue is hidden if CONFIG_REGULATORS is not set, because the
offending code is optimised away.
Notes for stable:
The issue first appears in commit 57d104c153 ("ufs: add UFS power
management support") but is inadvertently fixed in commit 60f0187031
("scsi: ufs: disable vccq if it's not needed by UFS device") which in
turn was reverted by commit 730679817d ("Revert "scsi: ufs: disable vccq
if it's not needed by UFS device""). So fix applies v3.18 to v4.5 and
v5.1+
Fixes: 57d104c153 ("ufs: add UFS power management support")
Fixes: 730679817d ("Revert "scsi: ufs: disable vccq if it's not needed by UFS device"")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If HBA initialization fails unexpectedly (exiting via probe_failed:), we
may fail to free vha->gnl.l. So that we don't attempt to double free, set
this pointer to NULL after a free and check for NULL at probe_failed: so we
know whether or not to call dma_free_coherent.
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Single lpfc fix, for a single cpu corner case.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXVKNpSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishcBWAQDV2FTB
Day/5EVD/hwtXNNaA2ygzy/Vi8QgNV0xqQOzRQD/cVoh8fMCqlV1yVqrvMikJRp4
Zrbnvhe0k4cGhdD8Dcg=
=Jpj2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Single lpfc fix, for a single-cpu corner case"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Fix crash when cpu count is 1 and null irq affinity mask
Commit 8c0d3a02c1 ("PCI: Add accessors for PCI Express Capability") added
accessors for the PCI Express Capability so that drivers didn't need to be
aware of differences between v1 and v2 of the PCI Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 8c0d3a02c1 ("PCI: Add accessors for PCI Express Capability") added
accessors for the PCI Express Capability so that drivers didn't need to be
aware of differences between v1 and v2 of the PCI Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable retv is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This should be 'pmcraid', not 'pcmraid'
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark switch cases where we are expecting to fall through.
Fix the following warnings (Building: rpc_defconfig arm):
drivers/scsi/arm/fas216.c: In function fas216_disconnect_intr :
drivers/scsi/arm/fas216.c:913:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (fas216_get_last_msg(info, info->scsi.msgin_fifo) == ABORT) {
^
drivers/scsi/arm/fas216.c:919:2: note: here
default: /* huh? */
^~~~~~~
drivers/scsi/arm/fas216.c: In function fas216_kick :
drivers/scsi/arm/fas216.c:1959:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
fas216_allocate_tag(info, SCpnt);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:1960:2: note: here
case TYPE_OTHER:
^~~~
drivers/scsi/arm/fas216.c: In function fas216_busservice_intr :
drivers/scsi/arm/fas216.c:1413:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
fas216_stoptransfer(info);
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:1414:2: note: here
case STATE(STAT_STATUS, PHASE_SELSTEPS):/* Sel w/ steps -> Status */
^~~~
drivers/scsi/arm/fas216.c:1424:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
fas216_stoptransfer(info);
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:1425:2: note: here
case STATE(STAT_MESGIN, PHASE_COMMAND): /* Command -> Message In */
^~~~
drivers/scsi/arm/fas216.c: In function fas216_funcdone_intr :
drivers/scsi/arm/fas216.c:1573:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if ((stat & STAT_BUSMASK) == STAT_MESGIN) {
^
drivers/scsi/arm/fas216.c:1579:2: note: here
default:
^~~~~~~
drivers/scsi/arm/fas216.c: In function fas216_handlesync :
drivers/scsi/arm/fas216.c:605:20: warning: this statement may fall through [-Wimplicit-fallthrough=]
info->scsi.phase = PHASE_MSGOUT_EXPECT;
~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:607:2: note: here
case async:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides a module parameter and sysfs interface to select
whether the queue depth for each device should be based on the value
suggested by firmware (the default) or the maximum supported by the
controller (can_queue).
Although we have a sysfs interface per sdev to change the queue depth of
individual scsi devices, this implementation provides a single sysfs entry
per shost to switch between the controller max and the value reported by
firmware. The module parameter can provide an interface for one time grub
settings and provides persistent settings across the boot.
[mkp: tweaked commit desc]
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make the code easier to read by converting 'goto' statements into
'return' statements.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following Coverity complaint:
Null-checking sp->u.iocb_cmd.u.ctarg.rsp suggests that it may be null, but
it has already been dereferenced on all paths leading to the check.
See also commit e374f9f592 ("scsi: qla2xxx: Migrate switch registration commands away from mailbox interface") # v4.16.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of calling qla2x00_fcport_event_handler() and letting the switch
statement inside that function decide which other function to call, call
the latter function directly. Remove the event member from the event_arg
structure because it is no longer needed. Remove the
qla_handle_els_plogi_done() function because it is never called.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is easy to mix up the QLA_* and the MBS_* status codes. Complain loudly
if that happens.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The C language supports implicit casting of void pointers to non-void
pointers. Remove explicit sts_entry_* casts that are not necessary.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Split srb_cmd.ctx into two pointers such that the compiler can check the
type of that pointer.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Not calling sp->done() from the command completion path is a severe bug.
Hence complain loudly if that happens.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The LIO core requires that the target driver callback functions
.queue_data_in() and .queue_status() call target_put_sess_cmd() or
transport_generic_free_cmd(). These calls may happen synchronously or
asynchronously. Make sure that one of these LIO functions is called in case
a command has been aborted. This patch avoids that the code for removing a
session hangs due to commands that do not make progress.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes: 694833ee00 ("scsi: tcm_qla2xxx: Do not allow aborted cmd to advance.") # v4.13.
Fixes: a07100e00a ("qla2xxx: Fix TMR ABORT interaction issue between qla2xxx and TCM") # v4.5.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since struct sg_table is used in nvme-fc-driver.h, include
<linux/scatterlist.h> from that header file.
Since no definitions or declarations from <linux/blk-mq.h> are used in the
qla_nvme.h header file, do not include <linux/blk-mq.h> from that header
file.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that this function crashes if mcmd == NULL.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of allocating a struct srb dynamically from inside .queuecommand(),
set qla2xxx_driver_template.cmd_size such that struct scsi_cmnd and struct
srb are contiguous. Do not call QLA_QPAIR_MARK_BUSY() /
QLA_QPAIR_MARK_NOT_BUSY() for SRBs associated with SCSI commands. That is
safe because scsi_remove_host() is called before queue pairs are deleted
and scsi_remove_host() waits for all outstanding SCSI commands to finish.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but makes the next patch
easier to read.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since all pointers passed to the srb_t.done() and srb_t.free() functions
have type srb_t, change the type of the first argument of these functions
from void * into struct srb *. This allows the compiler to verify the
argument types for these functions. This patch does not change any
functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the same approach for encoding the destination ID as the approach used
by qlt_update_vp_map().
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the firmware documentation responder mode must be set for ELS
pass-through IOCBs if a response is expected.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the firmware documentation the firmware expects all ELS
pass-through IOCB parameters in little endian format. Make this explicit.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes several Coverity complaints about reading data that has
not been initialized.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change makes it easier to detect qla24xx_read_flash_data() failures
and also to handle such failures. This change does not modify the behavior
of the driver since all callers ignore the qla24xx_read_flash_data()
return value.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce the be_id_t and le_id_t data types for Fibre Channel source and
destination ID formats supported by the firmware instead of using an
uint8_t[3] array. Introduce functions for converting from and to the
port_id_t data types. This patch does not change the behavior of the
qla2xxx driver but improves source code readability and also allows the
compiler to verify the endianness of Fibre Channel IDs.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Failure of a soft reset is a severe failure. Hence report such failures.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes the string manipulation code easier to verify.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pass the output buffer size to the code that generates a PCI info string
and check the output buffer size while generating a PCI info string.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Such a timeout is a severe issue. Hence complain if waiting for pending
commands times out. This patch fixes a small bug: it modifies
qla82xx_chip_reset_cleanup() such that the "Done waiting" message is
reported if qla82xx_chip_reset_cleanup() succeeded instead of if that
function failed.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make it clear to humans and also to the compiler that the string passed
as fourth argument is not modified.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes several Coverity complaints about not always checking
the qla2x00_wait_for_hba_online() return value.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following Coverity complaint:
Unintentional integer overflow (OVERFLOW_BEFORE_WIDEN)
overflow_before_widen: Potentially overflowing expression dma_eng_num *
65536U with type unsigned int (32 bits, unsigned) is evaluated using 32-bit
arithmetic, and then used in a context that expects an expression of type
uint64_t (64 bits, unsigned).
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was detected by Coverity.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set the r??_data_len variables before using these instead of after.
This patch fixes the following Coverity complaint:
const: At condition req_data_len != rsp_data_len, the value of req_data_len
must be equal to 0.
const: At condition req_data_len != rsp_data_len, the value of rsp_data_len
must be equal to 0.
dead_error_condition: The condition req_data_len != rsp_data_len cannot be
true.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes: a9b6f722f6 ("[SCSI] qla2xxx: Implementation of bidirectional.") # v3.7.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Read the FC port state once instead of twice. This patch fixes the
following Coverity complaint:
Unchecked return value (CHECKED_RETURN)
check_return: Calling atomic_read without checking return value (as is
done elsewhere 80 out of 92 times).
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since sess == NULL before 'goto out_term2' is executed, the code under 'if
(sess)' cannot be reached. Hence remove that code. This was detected by
Coverity.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes a Coverity complaint about not checking the sscanf()
return value.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following Coverity complaint:
Unchecked return value (CHECKED_RETURN)
check_return: Calling wait_for_completion_timeout without checking return
value (as is done elsewhere 14 out of 17 times).
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Delete the PLOGIN ACK data structure from the vha->plogi_ack_list before
freeing that data structure to avoid that that list gets corrupted.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is helpful when debugging this driver to have the firmware status code
available if a mailbox command fails. Hence report that firmware status
code.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qlt_remove_target() only calls qlt_release() if
vha->vha_tgt.qla_tgt != NULL, checking that pointer inside qlt_release()
is not necessary. This patch fixes the following Coverity complaint:
CID 188348 (#1 of 1): Dereference after null check (FORWARD_NULL)
var_deref_model: Passing null pointer &vha->vha_tgt.qla_tgt->tgt_list_entry
to list_del, which dereferences it.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Checking a pointer after it has been dereferenced is not useful. This was
detected by Coverity.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simplify the implementation of this function by using the %phC format
specifier instead of using explicit for-loops.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes the code that parses the GID list easier to read without
changing the behavior of the code.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that locking assumptions are verified at runtime if kernel
debugging is enabled.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but fixes a Coverity complaint
about using a scalar as an array.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make it clear that the CDB is not modified after processing of a SCSI
command has started.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes it clear that the tag, hwq and qpair variables are only
used in the mq path.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The value returned by this function is not used. Hence change the return
type of this function into 'void' and remove the return statement.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes it clear to humans and also to the compiler that
ql_dump_buffer() does not modify the memory the @buf argument points at.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qlt_make_local_sess() is defined before it is called, remove the
forward declaration of that function.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no bsg code in the qla_mr.c source file. Hence do not include
the <linux/bsg-lib.h> header file from qla_mr.c.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the put_unaligned_*() macros are used in this header file, include
the header file that defines these macros.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes: 15b7a68c1d ("scsi: qla2xxx: Introduce the dsd32 and dsd64 data structures") # v5.2-rc1.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Insert a space where required, surround complex expressions in macros with
parentheses, use the UL suffix instead of the (unsigned long) cast, do not
use line continuations when not necessary and do not explicitly initialize
static variables to zero.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I'm not sure how this happened but the patch that was intended to fix abort
handling was incomplete. This patch fixes that patch as follows:
- If aborting the SCSI command failed, wait until the SCSI command
completes.
- Return SUCCESS instead of FAILED if an abort attempt races with SCSI
command completion.
- Since qla2xxx_eh_abort() increments the sp reference count by calling
sp_get(), decrement the sp reference count before returning.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes: 219d27d714 ("scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qla2x00_abort_srb() starts with increasing the reference count of
@sp, decrease that same reference count before returning.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes: 219d27d714 ("scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands") # v5.2.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hi Linus,
Please, pull the following patches that mark switch cases where we are
expecting to fall through.
- Fix fall-through warnings in arm, sparc64, mips, i386 and s390.
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----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=6lSP
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fall-through fixes from Gustavo A. R. Silva:
"Mark more switch cases where we are expecting to fall through, fixing
fall-through warnings in arm, sparc64, mips, i386 and s390"
* tag 'Wimplicit-fallthrough-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
ARM: ep93xx: Mark expected switch fall-through
scsi: fas216: Mark expected switch fall-throughs
pcmcia: db1xxx_ss: Mark expected switch fall-throughs
video: fbdev: omapfb_main: Mark expected switch fall-throughs
watchdog: riowd: Mark expected switch fall-through
s390/net: Mark expected switch fall-throughs
crypto: ux500/crypt: Mark expected switch fall-throughs
watchdog: wdt977: Mark expected switch fall-through
watchdog: scx200_wdt: Mark expected switch fall-through
watchdog: Mark expected switch fall-throughs
ARM: signal: Mark expected switch fall-through
mfd: omap-usb-host: Mark expected switch fall-throughs
mfd: db8500-prcmu: Mark expected switch fall-throughs
ARM: OMAP: dma: Mark expected switch fall-throughs
ARM: alignment: Mark expected switch fall-throughs
ARM: tegra: Mark expected switch fall-through
ARM/hw_breakpoint: Mark expected switch fall-throughs
Mark switch cases where we are expecting to fall through.
Fix the following warnings (Building: rpc_defconfig arm):
drivers/scsi/arm/fas216.c: In function ‘fas216_disconnect_intr’:
drivers/scsi/arm/fas216.c:913:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (fas216_get_last_msg(info, info->scsi.msgin_fifo) == ABORT) {
^
drivers/scsi/arm/fas216.c:919:2: note: here
default: /* huh? */
^~~~~~~
drivers/scsi/arm/fas216.c: In function ‘fas216_kick’:
drivers/scsi/arm/fas216.c:1959:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
fas216_allocate_tag(info, SCpnt);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:1960:2: note: here
case TYPE_OTHER:
^~~~
drivers/scsi/arm/fas216.c: In function ‘fas216_busservice_intr’:
drivers/scsi/arm/fas216.c:1413:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
fas216_stoptransfer(info);
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:1414:2: note: here
case STATE(STAT_STATUS, PHASE_SELSTEPS):/* Sel w/ steps -> Status */
^~~~
drivers/scsi/arm/fas216.c:1424:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
fas216_stoptransfer(info);
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:1425:2: note: here
case STATE(STAT_MESGIN, PHASE_COMMAND): /* Command -> Message In */
^~~~
drivers/scsi/arm/fas216.c: In function ‘fas216_funcdone_intr’:
drivers/scsi/arm/fas216.c:1573:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if ((stat & STAT_BUSMASK) == STAT_MESGIN) {
^
drivers/scsi/arm/fas216.c:1579:2: note: here
default:
^~~~~~~
drivers/scsi/arm/fas216.c: In function ‘fas216_handlesync’:
drivers/scsi/arm/fas216.c:605:20: warning: this statement may fall through [-Wimplicit-fallthrough=]
info->scsi.phase = PHASE_MSGOUT_EXPECT;
~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:607:2: note: here
case async:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Updated driver version from 29.100.00.00 to 31.100.00.00 which is
equivalent to Phase 12 OOB.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In some cases, like while performing extensive expander reset or phy reset,
user may observe that drives are not visible in OS. Driver's
firmware-worker thread is blocked for more than 120 seconds resulting in a
call trace.
1. Received target add event for Device A and hence driver has registered
this device to SML by calling sas_rphy_add(). SML has half added this
device and returned the control to the driver by quitting from
sas_rphy_add() API, and started some background scanning on this device A.
2. While background scanning is going on device A, driver has received SAS
DEVICE STATUS CHANGE EVENT with RC code "Internal device reset" event and
hence driver has set tm_busy flag for this Device A from FW worker thread
context. When tm_busy flag is set then driver return scsi commands with
device busy status asking the kernel to retry the command after some time.
So background scanning for device A will be waiting for this tm_busy to be
cleared.
3. Meanwhile driver has received a target add event for Device B and hence
driver called sas_rphy_add() API to register this device with SML. But
since background scanning for Device A is still pending and SML is not
quitting from sas_rphy_add(), the driver’s firmware worker thread got
blocked.
4. Now driver has received SAS DEVICE STATUS CHANGE EVENT with RC code
"Internal device reset complete" event. But as driver’s firmware worker
thread got blocked in Step3, it can’t process this event and it was not
clearing the tm_busy flag and deadlock occurred (where SML was waiting for
tm_busy flag to be cleared and our FW worker thread is waiting for SML to
quit from sas_device_rphy_add() API).
Same deadlock will be observed even if device B is getting removed in
step3. So to limit these types of deadlocks driver will process the SAS
DEVICE STATUS CHANGE EVENT events from ISR context instead of processing
this event from worker thread context. This improvement avoids above
deadlock.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to reduce the performance drop depth observed on SATA HDD
when ATA PT command is outstanding.
Driver returns IO commands with status "SAM_STAT_BUSY" whenever ATA PT
command is outstanding. With this, IO commands will be retried until this
outstanding ATA PT to complete and hence we will observe drop in
performance.
As the driver is completing the subsequent IOs commands with SAM_STAT_BUSY
status, these IOs has to go though the block layer. Hence it adds latency
to the IOs and large performance drop is observed.
So to reduce this performance dropp, added improvement in driver to return
the subsequent IOs with SCSI_MLQUEUE_DEVICE_BUSY status instead of
completing the IOs with SAM_STAT_BUSY status when ATA PT command is
outstanding. Sending command back with SCSI_MLQUEUE_DEVICE_BUSY does not go
through complete block layer stack (as scsi_done won't be called) SML will
immediately retry the command and this method will avoid latency of block
layer stack and the performance impact will be reduced.
On Local setup, ran 512k sequential read IO operation on HGST SATA drive
with existing driver & with this improvement drivers and here is the
result,
1. With existing driver: IOs are running at bandwidth of ~230 rMB/s and
whenever any ATA PT command is outstanding (e.g issued from systemd-udevd
daemon) then this bandwidth drops to ~150 rMB/s.
2. With this improvement driver: IOs are running at bandwidth of ~230 rMB/s
and whenever any ATA PT command is outstanding then this bandwidth drops to
just ~190 rMB/s.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During HBA initialization time, if handshake operation fails due to some
firmware fault then currently driver is terminating the HBA
initialization. It is possible that HBA may come up properly if diag reset
is issued.
So improvement is made in driver in such a way that before terminating the
HBA initialization, driver checks the IOC state and if IOC state is in
fault state then issue diag reset for once. If diag reset is successful
then continue with HBA initialization else terminate the HBA
initialization.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently with sysfs parameter "drv_support_bitmap" driver exposes whether
driver supports toolbox memory move command or not.
And application should issue the toolbox memory move command only if driver
tell that memory move tool box command is supported through this sysfs
parameter.
In future we can utilize this sysfs parameter if any new feature is added
and need to notify the same to applications.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Host uses the Memory Move Tool to copy data from any source/destination
combination of system memory and IOC memory.
Memory Move Tool box request contains two SGE fields, First SGE field must
contains the source buffer details described by an MPI Simple SGE. The
second SGE field must contains the destination buffer details described by
an MPI Simple SGE.
Source -> Destination
1. IOC -> IOC (Both the SGE's will be filled by application)
2. HOST -> HOST (Both the SGE's will be filled by the host,
application should give sgl_offset to first SGE offset)
3. IOC -> HOST (Application will fill the first SGE and set the
sgl_offset to second SGE and hence driver fills
the second SGE)
4. HOST -> IOC (Application will fill IOC buffer information in the
first SGE and set the sgl_offset to second SGE.
Then driver will fill the second SGE with Host buffer
information and just before posting the command to the
firmware, driver will swap these two SGEs so that first
SGE contains the HOST buffer information and second SGE
contains the IOC information.
Driver has to take care only of the 4th case, other three cases are by
default supported by the current driver design.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If driver sees the NVMe drive with "DEVICE_BLOCKED" AccessStatus in its
PCIe Device Page0, then driver removes the drive from its internal list and
does not allow any IOCTL commands to be sent to the drive and will return
the IOCTLs with "-ENODEV" status.
The driver will now allow NVMe Encapsulated IOCTL issued to the NVMe device
with an access status of DEVICE_BLOCKED. This change allows the user to
flash new drive firmware online and revive the drive.
Add NVMe device only the driver's internal list even though the device is
in the blocked state so that the device will be visible to Apps. This way
Apps can send NVMe Encapsulated IOCTLs to this drive and bring the drive
online. This NVMe drive with DEVICE_BLOCKED access status won't added to
the SML, it will be added only in the driver's internal list.
[mkp: clarified desc]
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SES device of managed PCIe switch will be enumerated same as NVMe drives.
The device info type for this SES device is
MPI26_PCIE_DEVINFO_SCSI (0x4),
whereas the device info type for NVMe drives is
MPI26_PCIE_DEVINFO_NVME (0x3).
Based on this device info type driver determines whether the device is NVMe
drive or a SES device of a managed PCIe switch.
This SES device doesn't have the PCIe device page 2 information like NVMe
drives, so driver won't read PCIe device page 2 information for SES device.
This SES device uses only IEEE SGL's, So driver build's IEEE SGL's whenever
it receives any SCSI commands for this SES device.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated MPI to 2.6.8 specification and header files to 2.00.54.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue:
During online Firmware upgrade operations it is possible that MaxDevHandles
filled in IOCFacts may change with new FW. With this we may observe kernel
panics when driver try to access the pd_handles or blocking_handles buffers
at offset greater than the old firmware's MaxDevHandle value.
Fix:
_base_check_ioc_facts_changes() looks for increase/decrease in IOCFacts
attributes during online firmware upgrade and increases the pd_handles,
blocking_handles, etc buffer sizes to new firmware's MaxDevHandle value if
this new firmware's MaxDevHandle value is greater than the old firmware's
MaxDevHandle value.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver gets a request frame from the free pool of DMA-able request frames
and fill in the required information and pass the address of the frame to
IOC/FW to pull the complete request frame. In certain places the driver
used the request frame allocated from the free pool without completely
clearing the previous data stored in it. The request contents were cleared
only for the size of the new request to be issued and that left out some
stale data in the unused part of the request. Though the IOC/FW is not
expected to access the request beyond the specified size, it is good
practice to clear complete request message frame.
So reinitialize the complete request message frame with 0s before using
it.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PCIe Lane margin tool box request requires IEEE sgl's and hence driver
fills the SGL field with IEEE sgl's while issuing the PCIe Lane margin
ioctl request to the HBA firmware.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several occasions where variable rc is being initialized with a
value that is never read and error is being re-assigned a little later on.
Clean up the code by removing rc entirely and just returning the return
value from the call to pm8001_issue_ssp_tmf
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In hisi_sas_lu_reset(), we call internal abort for SAS and SATA device
codepaths -> consolidate into a single call.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The format specifier "%p" can leak kernel address, and use "%pK" instead.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove some unnecessary code, including:
- Explicit zeroing of memory allocated for dmam_alloc_coherent()
- Some duplicated code
- Some redundant masking
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For functions which always return 0, which is never checked, make to return
void.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It will free irq automatically if devm_request_irq() failed, so drop
free_irq() if devm_request_irq() failed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SMP frame response is written to the command table and not the SMP
response pointer from libsas, so don't bother DMA mapping (and unmapping)
the SMP response from libsas.
Suggested-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The call to kmap_atomic() in the SMP command completion code is
unnecessary, since kmap() is only really concerned with highmem, which is
not relevant on arm64. The controller only finds itself in arm64 systems.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For a system with PAGE_SIZE of 16K or 64K, the size every time we want to
alloc may be small like 4K, but for function dmam_alloc_coherent(), the
least size it allocates is PAGE_SIZE, so it will waste much memory for the
situation.
To solve the issue, limit the minimum allocation size of slot buf to
PAGE_SIZE.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For struct hisi_sas_status_buffer, it contains struct hisi_sas_err_record
and iu[1024]. The struct iu[1024] will be filled fully by the response of
disks, so it is not need to initialize them to 0, but for the struct
hisi_sas_err_record, SAS controller only fill some fields of
hisi_sas_err_record according to hw designer, so it should be initialised
to 0. After the change, cpu utilization percentage of memset() is changed
from 1.7% to 0.12%.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix a possible out-of-bounds access in hisi_sas_debug_I_T_nexus_reset().
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The AXI and RAS register values should also should be snapshot at debugfs.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The value of IOST/ITCT is updated to cache first, and then synchronize to
DDR periodically. So the value in IOST/ITCT cache is the latest data and
it's important for debugging.
So, the HW cache of IOST and ITCT should be snapshot at debugfs.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix how the pointer is set in hisi_sas_debugfs_iost_show() and
hisi_sas_debugfs_itct_show().
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit 1273d65f29 ("scsi: hisi_sas: change queue depth from 512 to
4096"), the depth of each queue is the same as the max IPTT in the system.
As such, as long as we have an IPTT allocated, we will have enough space on
any delivery queue.
All .get_free_slot functions were checking for space on the queue by
reading the DQ read pointer. Drop this, and also raise the code into common
code, as there is nothing hw specific remaining.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a small optimisation to be had by making the max IPTT the same for
all hw revisions, that being we can drop the check for read and write
pointer being the same in the get free slot function.
Change v1 hw to have max IPTT of 4096 - same as v2 and v3 hw - and
drop hisi_sas_hw.max_command_entries.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a configurations runs with a single cpu (such as a kdump kernel),
which causes the driver to request a single vector, when the driver
subsequently requests an irq affinity mask, the mask comes back null. The
driver currently does nothing in this scenario, which leaves mappings to
hardware queues incomplete and crashes the system.
Fix by recognizing the null mask and assigning the vector to the first cpu
in the system.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Configure CDNS_UFS_REG_HCLKDIV in .hce_enable_notify() instead of
.setup_clock() because if UFSHCD resets the controller ip because of phy or
device related errors then CDNS_UFS_REG_HCLKDIV is reset to default value
and .setup_clock() is not called later in the sequence whereas
.hce_enable_notify will be called everytime controller is reenabled.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The data structure used for log messages is so large that it can cause a
boot failure. Since allocations from that data structure can fail anyway,
use kmalloc() / kfree() instead of that data structure.
See also https://bugzilla.kernel.org/show_bug.cgi?id=204119.
See also commit ded85c193a ("scsi: Implement per-cpu logging buffer") # v4.0.
Reported-by: Jan Palus <jpalus@fastmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Jan Palus <jpalus@fastmail.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If scsi_target_block() fails that can break the code that calls this
function. Hence complain loudly if scsi_target_block() fails.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The only 'new_state' values passed by upstream kernel code to
scsi_internal_device_unblock_nowait() are SDEV_RUNNING and
SDEV_TRANSPORT_OFFLINE. These are the only values that should be passed to
this function. Hence check the value of the 'new_state' argument to avoid
that scsi_internal_device_unblock_nowait() would be used to trigger an
illegal SCSI device state transition. In this context 'illegal' means not
allowed by scsi_device_set_state().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Define new a type: uc_string_id for easier string handling and less
casting. Reduce number or string copies in price of a dynamic allocation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: m68k):
drivers/scsi/wd33c93.c: In function round_4 :
drivers/scsi/wd33c93.c:1856:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 2: ++x;
^~~
drivers/scsi/wd33c93.c:1857:3: note: here
case 3: ++x;
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/scsi/sun3_scsi.c: warning: this statement may fall through
[-Wimplicit-fallthrough=]: => 399:9, 403:9
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings (Building: sparc defconfig):
drivers/scsi/qlogicpti.c: In function 'qlogicpti_mbox_command':
drivers/scsi/qlogicpti.c:202:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 6: sbus_writew(param[5], qpti->qregs + MBOX5);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:203:2: note: here
case 5: sbus_writew(param[4], qpti->qregs + MBOX4);
^~~~
drivers/scsi/qlogicpti.c:203:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 5: sbus_writew(param[4], qpti->qregs + MBOX4);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:204:2: note: here
case 4: sbus_writew(param[3], qpti->qregs + MBOX3);
^~~~
drivers/scsi/qlogicpti.c:204:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 4: sbus_writew(param[3], qpti->qregs + MBOX3);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:205:2: note: here
case 3: sbus_writew(param[2], qpti->qregs + MBOX2);
^~~~
drivers/scsi/qlogicpti.c:205:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 3: sbus_writew(param[2], qpti->qregs + MBOX2);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:206:2: note: here
case 2: sbus_writew(param[1], qpti->qregs + MBOX1);
^~~~
drivers/scsi/qlogicpti.c:206:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 2: sbus_writew(param[1], qpti->qregs + MBOX1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:207:2: note: here
case 1: sbus_writew(param[0], qpti->qregs + MBOX0);
^~~~
drivers/scsi/qlogicpti.c:256:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 6: param[5] = sbus_readw(qpti->qregs + MBOX5);
~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:257:2: note: here
case 5: param[4] = sbus_readw(qpti->qregs + MBOX4);
^~~~
drivers/scsi/qlogicpti.c:257:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 5: param[4] = sbus_readw(qpti->qregs + MBOX4);
~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:258:2: note: here
case 4: param[3] = sbus_readw(qpti->qregs + MBOX3);
^~~~
drivers/scsi/qlogicpti.c:258:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 4: param[3] = sbus_readw(qpti->qregs + MBOX3);
~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:259:2: note: here
case 3: param[2] = sbus_readw(qpti->qregs + MBOX2);
^~~~
drivers/scsi/qlogicpti.c:259:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 3: param[2] = sbus_readw(qpti->qregs + MBOX2);
~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:260:2: note: here
case 2: param[1] = sbus_readw(qpti->qregs + MBOX1);
^~~~
drivers/scsi/qlogicpti.c:260:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
case 2: param[1] = sbus_readw(qpti->qregs + MBOX1);
~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qlogicpti.c:261:2: note: here
case 1: param[0] = sbus_readw(qpti->qregs + MBOX0);
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/scsi/ibmvscsi/ibmvfc.c: In function 'ibmvfc_npiv_login_done':
drivers/scsi/ibmvscsi/ibmvfc.c:4022:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
ibmvfc_retry_host_init(vhost);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvfc.c:4023:2: note: here
case IBMVFC_MAD_DRIVER_FAILED:
^~~~
drivers/scsi/ibmvscsi/ibmvfc.c: In function 'ibmvfc_bsg_request':
drivers/scsi/ibmvscsi/ibmvfc.c:1830:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
port_id = (bsg_request->rqst_data.h_els.port_id[0] << 16) |
~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
(bsg_request->rqst_data.h_els.port_id[1] << 8) |
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
bsg_request->rqst_data.h_els.port_id[2];
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvfc.c:1833:2: note: here
case FC_BSG_RPT_ELS:
^~~~
drivers/scsi/ibmvscsi/ibmvfc.c:1838:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
port_id = (bsg_request->rqst_data.h_ct.port_id[0] << 16) |
~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
(bsg_request->rqst_data.h_ct.port_id[1] << 8) |
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
bsg_request->rqst_data.h_ct.port_id[2];
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvfc.c:1841:2: note: here
case FC_BSG_RPT_CT:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The commit de516379e8 ("scsi: megaraid_sas: changes to function
prototypes") introduced a comilation warning due to it changed the function
prototype of read_fw_status_reg() to take an instance pointer instead, but
forgot to remove an unused variable.
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function
'megasas_fusion_update_can_queue':
drivers/scsi/megaraid/megaraid_sas_fusion.c:326:39: warning: variable
'reg_set' set but not used [-Wunused-but-set-variable]
struct megasas_register_set __iomem *reg_set;
^~~~~~~
Fixes: de516379e8 ("scsi: megaraid_sas: changes to function prototypes")
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/megaraid/megaraid_sas_fusion.c:3369:1: warning: symbol 'complete_cmd_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3535:6: warning: symbol 'megasas_sync_irqs' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3554:1: warning: symbol 'megasas_complete_cmd_dpc_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3573:13: warning: symbol 'megasas_isr_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3604:1: warning: symbol 'build_mpt_mfi_pass_thru' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3661:40: warning: symbol 'build_mpt_cmd' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3688:1: warning: symbol 'megasas_issue_dcmd_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3881:5: warning: symbol 'megasas_wait_for_outstanding_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:4005:6: warning: symbol 'megasas_refire_mgmt_cmd' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:4525:25: warning: symbol 'megasas_get_peer_instance' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:4825:7: warning: symbol 'megasas_fusion_crash_dump' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current driver report dev_loss_tmo to 0 for NVMe devices with short cable
pull. This causes NVMe controller to be freed along with NVMe namespace.
The side affect is IO would stop. By not setting dev_loss_tmo to 0, NVMe
namespace would stay until cable is plugged back in. This allows IO to
resume afterward.
[mkp: commit desc]
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A hang was observed in the fcport delete path when the device was
responding slow and an issue-lip path (results in session termination) was
taken.
Fix this by issuing logo requests unconditionally.
PID: 19491 TASK: ffff8e23e67bb150 CPU: 0 COMMAND: "kworker/0:0"
#0 [ffff8e2370297bf8] __schedule at ffffffffb4f7dbb0
#1 [ffff8e2370297c88] schedule at ffffffffb4f7e199
#2 [ffff8e2370297c98] schedule_timeout at ffffffffb4f7ba68
#3 [ffff8e2370297d40] msleep at ffffffffb48ad9ff
#4 [ffff8e2370297d58] qlt_free_session_done at ffffffffc0c32052 [qla2xxx]
#5 [ffff8e2370297e20] process_one_work at ffffffffb48bcfdf
#6 [ffff8e2370297e68] worker_thread at ffffffffb48bdca6
#7 [ffff8e2370297ec8] kthread at ffffffffb48c4f81
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Leverage the generic routine, qla24xx_update_fw_options(), for the
configuration of firmware options for ISP27xx/ISP28xx.
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following sequence of event leads to NVME port disappearing:
- device port shut
- nvme_fc_unregister_remoteport
- device port online
- remote port delete completes
- relogin is scheduled
- "post gidpn" message appears due to rscn generation # mismatch
In short, if a device comes back online sooner than an unregister
completion, a mismatch in rscn generation number occurs, which is not
handled correctly during device relogin. Fix this by starting with a redo
of GNL.
When ql2xextended_error_logging is enabled, the re-plugged device's
discovery stops with the following messages printed:
--8<--
qla2xxx [0000:41:00.0]-480d:3: Relogin scheduled.
qla2xxx [0000:41:00.0]-4800:3: DPC handler sleeping.
qla2xxx [0000:41:00.0]-2902:3: qla24xx_handle_relogin_event 21:00:00:24:ff:17:9e:91 DS 0 LS 7 P 0 del 2 cnfl
(null) rscn 1|2 login 1|2 fl 1
qla2xxx [0000:41:00.0]-28e9:3: qla24xx_handle_relogin_event 1666 21:00:00:24:ff:17:9e:91 post gidpn
qla2xxx [0000:41:00.0]-480e:3: Relogin end.
--8<--
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code misses or fails to account for proper recovery during early
initialization failures:
- Properly unwind allocations during probe() failures.
- Protect against non-initialization memory allocations during
unwinding.
- Propagate error status during HW initialization.
- Release SCSI host reference when memory allocations fail.
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when fabric scan thread encounters IOCB Q Full, schedule a delayed work to
retry fabric scan.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For any qla2xxx async command, the SRB buffer is used to send it. In
setting up the SRB buffer, the timer for this command is started before all
memory allocation has finished. Under low memory pressure, memory alloc
can go to sleep and not wake up before the timer expires. Once timer has
expired, the timer thread will access uninitialize fields resulting into
NULL pointer crash.
This patch fixes this crash by moving the start of timer after everything
is setup.
backtrace shows following
PID: 3720 TASK: ffff996928401040 CPU: 0 COMMAND: "qla2xxx_1_dpc"
0 [ffff99652751b698] __schedule at ffffffff965676c7
1 [ffff99652751b728] schedule at ffffffff96567bc9
2 [ffff99652751b738] schedule_timeout at ffffffff965655e8
3 [ffff99652751b7e0] io_schedule_timeout at ffffffff9656726d
4 [ffff99652751b810] congestion_wait at ffffffff95fd8d12
5 [ffff99652751b870] isolate_migratepages_range at ffffffff95fddaf3
6 [ffff99652751b930] compact_zone at ffffffff95fdde96
7 [ffff99652751b980] compact_zone_order at ffffffff95fde0bc
8 [ffff99652751ba20] try_to_compact_pages at ffffffff95fde481
9 [ffff99652751ba80] __alloc_pages_direct_compact at ffffffff9655cc31
10 [ffff99652751bae0] __alloc_pages_slowpath at ffffffff9655d101
11 [ffff99652751bbd0] __alloc_pages_nodemask at ffffffff95fc0e95
12 [ffff99652751bc80] dma_generic_alloc_coherent at ffffffff95e3217f
13 [ffff99652751bcc8] x86_swiotlb_alloc_coherent at ffffffff95e6b7a1
14 [ffff99652751bcf8] qla2x00_rft_id at ffffffffc055b5e0 [qla2xxx]
15 [ffff99652751bd50] qla2x00_loop_resync at ffffffffc0533e71 [qla2xxx]
16 [ffff99652751be68] qla2x00_do_dpc at ffffffffc05210ca [qla2xxx]
PID: 0 TASK: ffffffff96a18480 CPU: 0 COMMAND: "swapper/0"
0 [ffff99652fc03ae0] machine_kexec at ffffffff95e63674
1 [ffff99652fc03b40] __crash_kexec at ffffffff95f1ce12
2 [ffff99652fc03c10] crash_kexec at ffffffff95f1cf00
3 [ffff99652fc03c28] oops_end at ffffffff9656c758
4 [ffff99652fc03c50] no_context at ffffffff9655aa7e
5 [ffff99652fc03ca0] __bad_area_nosemaphore at ffffffff9655ab15
6 [ffff99652fc03cf0] bad_area_nosemaphore at ffffffff9655ac86
7 [ffff99652fc03d00] __do_page_fault at ffffffff9656f6b0
8 [ffff99652fc03d70] do_page_fault at ffffffff9656f915
9 [ffff99652fc03da0] page_fault at ffffffff9656b758
[exception RIP: unknown or invalid address]
RIP: 0000000000000000 RSP: ffff99652fc03e50 RFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff99652b79a600 RCX: ffff99652b79a760
RDX: ffff99652b79a600 RSI: ffffffffc0525ad0 RDI: ffff99652b79a600
RBP: ffff99652fc03e60 R8: ffffffff96a18a18 R9: ffffffff96ee3c00
R10: 0000000000000002 R11: ffff99652fc03de8 R12: ffff99652b79a760
R13: 0000000000000100 R14: ffffffffc0525ad0 R15: ffff99652b79a600
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
10 [ffff99652fc03e50] qla2x00_sp_timeout at ffffffffc0525af8 [qla2xxx]
11 [ffff99652fc03e68] call_timer_fn at ffffffff95ea7f58
12 [ffff99652fc03ea0] run_timer_softirq at ffffffff95eaa3bd
13 [ffff99652fc03f18] __do_softirq at ffffffff95ea0f05
14 [ffff99652fc03f88] call_softirq at ffffffff9657832c
15 [ffff99652fc03fa0] do_softirq at ffffffff95e2e675
16 [ffff99652fc03fc0] irq_exit at ffffffff95ea1285
17 [ffff99652fc03fd8] smp_apic_timer_interrupt at ffffffff965796c8
18 [ffff99652fc03ff0] apic_timer_interrupt at ffffffff96575df2
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relogin fails to move forward due to scan_state flag indicating device is
not there. Before relogin process, Session delete process accidently
modified the scan_state flag.
[mkp: typos plus corrected Fixes: sha as reported by sfr]
Fixes: 2dee552102 ("scsi: qla2xxx: Fix login state machine freeze")
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement .cleanup_rq() callback for freeing driver private part
of the request. Then we can avoid to leak this part if the request isn't
completed by SCSI, and freed by blk-mq or upper layer(such as dm-rq) finally.
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: <stable@vger.kernel.org>
Fixes: 396eaf21ee ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch implements the zone reset all operation for sd_zbc.c. We add
a new boolean parameter for the sd_zbc_setup_reset_cmd() to indicate
REQ_OP_ZONE_RESET_ALL command setup. Along with that we add support in
the completion path for the zone reset all.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Seven fixes to four drivers with no core changes. The mpt3sas one is
theoretical until we get a CPU that goes up to 64 bits physical, the
qla2xxx one fixes an oops in a driver initialization error leg and the
others are mostly cosmetic.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXURSriYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWpKAQCbTaKz
AWOXWaMUoL26nZ036slYx9KjxcXS/MFuDXCAnQEA5ww+AfKurovX62i3B7YqVDxm
j0TBq+LvzUUNcrA+JU8=
=NfZ0
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven fixes to four drivers with no core changes.
The mpt3sas one is theoretical until we get a CPU that goes up to 64
bits physical, the qla2xxx one fixes an oops in a driver
initialization error leg and the others are mostly cosmetic"
[ The fcoe patches may be worth highlighting - they may be "just"
cleanups, but they simplify and fix the odd fc_rport_priv structure
handling rules so that the new gcc-9 warnings about memset crossing
structure boundaries are gone.
The old code was hard for humans to understand too, and really
confused the compiler sanity checks - Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix possible fcport null-pointer dereferences
scsi: mpt3sas: Use 63-bit DMA addressing on SAS35 HBA
scsi: hpsa: remove printing internal cdb on tag collision
scsi: hpsa: correct scsi command status issue after reset
scsi: fcoe: pass in fcoe_rport structure instead of fc_rport_priv
scsi: fcoe: Embed fc_rport_priv in fcoe_rport structure
scsi: libfc: Whitespace cleanup in libfc.h
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reject eh_{abort|device_reset|target_reset} when rport is being torn down
or chip is down.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware dump captured during LOOP Init error does not yield any
significant information. This patch removes call to trigger firmware dump
collection during Loop Initialization.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For target mode, the default number of Q-Pairs allowed to use is 2. If the
number of Q-Pairs allocated is lower than the default Q-Pairs, then lower
value should be the set as default.
[mkp: typo]
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an abort times out, the Abort IOCB completion and Abort timer can race
against each other. This patch provides unique error code for timer path to
allow proper cleanup.
[mkp: typo]
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With debug kernel we see following wanings indicating memory leak.
[28809.523959] WARNING: CPU: 3 PID: 6790 at lib/dma-debug.c:978
dma_debug_device_change+0x166/0x1d0
[28809.523964] pci 0000:0c:00.6: DMA-API: device driver has pending DMA
allocations while released from device [count=5]
[28809.523964] One of leaked entries details: [device
address=0x00000002aefe4000] [size=8208 bytes] [mapped with DMA_BIDIRECTIONAL]
[mapped as coherent]
Fix this by unmapping DMA memory.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We can request task management IOCTL command(MPI2_FUNCTION_SCSI_TASK_MGMT)
to /dev/mpt3ctl. If the given task_type is either abort task or query
task, it may need a field named "Initiator Port Transfer Tag to Manage" in
the IU.
Current code does not support to check target IPTT tag from the tm_request.
This patch introduces to check TaskMID given from the userspace as a target
tag. We have a rule of relationship between
(struct request *req->tag) and smid in mpt3sas_base.c:
3318 u16
3319 mpt3sas_base_get_smid_scsiio(struct MPT3SAS_ADAPTER *ioc, u8 cb_idx,
3320 struct scsi_cmnd *scmd)
3321 {
3322 struct scsiio_tracker *request = scsi_cmd_priv(scmd);
3323 unsigned int tag = scmd->request->tag;
3324 u16 smid;
3325
3326 smid = tag + 1;
So if we want to abort a request tagged #X, then we can pass (X + 1) to
this IOCTL handler. Otherwise, user space just can pass 0 TaskMID to abort
the first outstanding smid which is legacy behaviour.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: MPT-FusionLinux.pdl@broadcom.com
Signed-off-by: Minwoo Im <minwoo.im@samsung.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings (Building: powerpc allyesconfig):
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c: In function 'ibmvscsis_adapter_info':
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c:1582:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (connection_broken(vscsi))
^
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c:1584:2: note: here
default:
^~~~~~~
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c: In function 'ibmvscsis_ping_response':
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c:2494:16: warning: this statement may fall through [-Wimplicit-fallthrough=]
vscsi->flags |= CLIENT_FAILED;
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c:2495:2: note: here
case H_DROPPED:
^~~~
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c:2496:16: warning: this statement may fall through [-Wimplicit-fallthrough=]
vscsi->flags |= RESPONSE_Q_DOWN;
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c:2497:2: note: here
case H_REMOTE_PARM:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Bryant G. Ly <bly@catalogicsoftware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/scsi/cxlflash/main.c: In function 'send_afu_cmd':
drivers/scsi/cxlflash/main.c:2347:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (rc) {
^
drivers/scsi/cxlflash/main.c:2357:2: note: here
case -EAGAIN:
^~~~
drivers/scsi/cxlflash/main.c: In function 'term_intr':
drivers/scsi/cxlflash/main.c:754:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (index == PRIMARY_HWQ)
^
drivers/scsi/cxlflash/main.c:756:2: note: here
case UNMAP_TWO:
^~~~
drivers/scsi/cxlflash/main.c:757:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
cfg->ops->unmap_afu_irq(hwq->ctx_cookie, 2, hwq);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/cxlflash/main.c:758:2: note: here
case UNMAP_ONE:
^~~~
drivers/scsi/cxlflash/main.c:759:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
cfg->ops->unmap_afu_irq(hwq->ctx_cookie, 1, hwq);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/cxlflash/main.c:760:2: note: here
case FREE_IRQ:
^~~~
drivers/scsi/cxlflash/main.c: In function 'cxlflash_remove':
drivers/scsi/cxlflash/main.c:975:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
cxlflash_release_chrdev(cfg);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/cxlflash/main.c:976:2: note: here
case INIT_STATE_SCSI:
^~~~
drivers/scsi/cxlflash/main.c:978:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
scsi_remove_host(cfg->host);
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/cxlflash/main.c:979:2: note: here
case INIT_STATE_AFU:
^~~~
drivers/scsi/cxlflash/main.c:980:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
term_afu(cfg);
^~~~~~~~~~~~~
drivers/scsi/cxlflash/main.c:981:2: note: here
case INIT_STATE_PCI:
^~~~
drivers/scsi/cxlflash/main.c:983:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
pci_disable_device(pdev);
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/cxlflash/main.c:984:2: note: here
case INIT_STATE_NONE:
^~~~
drivers/scsi/cxlflash/main.c: In function 'num_hwqs_store':
drivers/scsi/cxlflash/main.c:3018:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (cfg->state == STATE_NORMAL)
^
drivers/scsi/cxlflash/main.c:3020:2: note: here
default:
^~~~~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Matthew R. Ochs <mrochs@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a copy and paste bug here. It uses EVENT_TRIGGERS size instead of
SCSI_TRIGGERS size but fortunately both size are 84 bytes so it doesn't
affect runtime.
These days the preferred style is to just say sizeof(object) instead of
sizeof(type) so I have updated the function to the latest style as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In qla2x00_alloc_fcport(), fcport is assigned to NULL in the error
handling code on line 4880:
fcport = NULL;
Then fcport is used on lines 4883-4886:
INIT_WORK(&fcport->del_work, qla24xx_delete_sess_fn);
INIT_WORK(&fcport->reg_work, qla_register_fcport_fn);
INIT_LIST_HEAD(&fcport->gnl_entry);
INIT_LIST_HEAD(&fcport->list);
Thus, possible null-pointer dereferences may occur.
To fix these bugs, qla2x00_alloc_fcport() directly returns NULL
in the error handling code.
These bugs are found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Although SAS3 & SAS3.5 IT HBA controllers support 64-bit DMA addressing, as
per hardware design, if DMA-able range contains all 64-bits
set (0xFFFFFFFF-FFFFFFFF) then it results in a firmware fault.
E.g. SGE's start address is 0xFFFFFFFF-FFFF000 and data length is 0x1000
bytes. when HBA tries to DMA the data at 0xFFFFFFFF-FFFFFFFF location then
HBA will fault the firmware.
Driver will set 63-bit DMA mask to ensure the above address will not be
used.
Cc: <stable@vger.kernel.org> # 5.1.20+
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We can use for_each_set_bit() to slightly simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove racy printing of internal commands. Completion thread can be
cleaning up the command in parallel.
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use vzalloc instead of using vmalloc to allocate memory and then zeroing it
with memset. This simplifies the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1697c6a64c ("scsi: fdomain: Add register definitions") somehow
missed the uses of CFG1_IRQ_MASK in the Futire Domain ISA driver, leaving
the magic numbers intact. Fix this issue (with no change in the generated
object file), removing an excess empty line, while at it...
Fixes: 1697c6a64c ("scsi: fdomain: Add register definitions")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1697c6a64c ("scsi: fdomain: Add register definitions") somehow
missed the masking of the 'status' variable with the SCSI phase mask in
fdomain_work(), leaving the magic number intact. Fix this issue; while at
it, change the order of BSTAT_{MSG|CMD|IO} bits in the MESSAGE IN
phase *case* (with no change in the generated object file).
Fixes: 1697c6a64c ("scsi: fdomain: Add register definitions")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1697c6a64c ("scsi: fdomain: Add register definitions") somehow
missed the use of BCTL_RST in fdomain_reset(), leaving the magic number
intact. Fix this issue (with no change in the generated object file).
Fixes: 1697c6a64c ("scsi: fdomain: Add register definitions")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
kmem_cache_destroy() can handle NULL pointer correctly, so there is no need
to check NULL pointer before calling kmem_cache_destroy().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A null check before dma_pool_destroy is redundant, so remove it. This is
detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a generic helper to match any/all devices. Using this
introduce new wrappers {bus/driver/class}_find_next_device().
Cc: Elie Morisse <syniurge@gmail.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI
Link: https://lore.kernel.org/r/20190723221838.12024-7-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using the generic 'fc_rport_priv' structure as argument and then
having to painstakingly outcast this to fcoe_rport we should be passing the
fcoe_rport structure itself and reduce complexity.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gcc-9 complains for a memset across pointer boundaries, which happens as
the code tries to allocate a flexible array on the stack. Turns out we
cannot do this without relying on gcc-isms, so with this patch we'll embed
the fc_rport_priv structure into fcoe_rport, can use the normal
'container_of' outcast, and will only have to do a memset over one
structure.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nine fixes: The most important core one is the dma_max_mapping_size
fix that corrects the boot problem Gunter Roeck was having. A couple
of other driver only fixes are significant, like the cxgbi selector
support addition, the alua 2 second delay and the fdomain build fix.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXTtaMiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdrUAP4omvmb
8y9TtFlcUN2bkjY/7/X3aiJIbCBXL9ouW9UtwwD9FUW/Tx+3+agDp1mosbtsVT6V
8lY/Yc/J1HRttW0x2e8=
=PL2C
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine fixes: The most important core one is the dma_max_mapping_size
fix that corrects the boot problem Gunter Roeck was having. A couple
of other driver only fixes are significant, like the cxgbi selector
support addition, the alua 2 second delay and the fdomain build fix"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_dh_alua: always use a 2 second delay before retrying RTPG
scsi: ibmvfc: fix WARN_ON during event pool release
scsi: fcoe: fix a typo
scsi: megaraid_sas: Make some functions static
scsi: megaraid_sas: fix panic on loading firmware crashdump
scsi: megaraid_sas: fix spelling mistake "megarid_sas" -> "megaraid_sas"
scsi: core: fix the dma_max_mapping_size call
scsi: fdomain: fix building pcmcia front-end
scsi: target: cxgbit: add support for IEEE_8021QAZ_APP_SEL_STREAM selector
Retrying immediately after we've received a 'transitioning' sense code is
pretty much pointless, we should always use a delay before retrying. So
ensure the default delay is applied before retrying.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Tested-by: Zhangguanghui <zhang.guanghui@h3c.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
#define relative to FCOE CTLR start with FCOE_CTLR, except
FCOE_CTRL_SOL_TOV.
This is likely a typo and CTRL should be CTLR here as well.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/megaraid/megaraid_sas_fusion.c:541:1: warning: symbol 'megasas_alloc_cmdlist_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:580:1: warning: symbol 'megasas_alloc_request_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:661:1: warning: symbol 'megasas_alloc_reply_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:738:1: warning: symbol 'megasas_alloc_rdpq_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:920:1: warning: symbol 'megasas_alloc_cmds_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:1740:1: warning: symbol 'megasas_init_adapter_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:1966:1: warning: symbol 'map_cmd_status' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:2379:1: warning: symbol 'megasas_set_pd_lba' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:2718:1: warning: symbol 'megasas_build_ldio_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3215:1: warning: symbol 'megasas_build_io_fusion' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_fusion.c:3328:6: warning: symbol 'megasas_prepare_secondRaid1_IO' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While loading fw crashdump in function fw_crash_buffer_show(), left bytes
in one dma chunk was not checked, if copying size over it, overflow access
will cause kernel panic.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix spelling mistake in kernel warning message and replace printk with with
pr_warn.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should only call dma_max_mapping_size for devices that have a DMA mask
set, otherwise we can run into a NULL pointer dereference that will crash
the system.
Also we need to do right shift to get the sectors from the size in bytes,
not a left shift.
Fixes: bdd17bdef7 ("scsi: core: take the DMA max mapping size into account")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get a warning when CONFIG_SCSI_LOWLEVEL is disabled here:
WARNING: unmet direct dependencies detected for SCSI_FDOMAIN
Depends on [n]: SCSI_LOWLEVEL [=n] && SCSI [=y]
Selected by [m]:
- PCMCIA_FDOMAIN [=m] && SCSI_LOWLEVEL_PCMCIA [=y] && SCSI [=y] && PCMCIA [=y] && m && MODULES [=y]
Move all of SCSI_LOWLEVEL_PCMCIA inside of the existing SCSI_LOWLEVEL
section. Very few people use the PCMCIA support these days, and they likely
don't mind having to turn on SCSI_LOWLEVEL as well. This way we avoid the
link error and get a more sensible structure.
Fixes: 7d47fa065e62 ("scsi: fdomain: Add PCMCIA support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to change msleep() to usleep_range() based on
Documentation/timers/timers-howto.txt. It suggests using usleep_range()
for small msec(1ms - 20ms) since msleep() will often sleep longer than
desired value.
After changing, booting time will be 5ms-10ms faster than before. I
tested this change on two different platforms, one has 5ms faster, another
one is about 10ms. I think this is different on different platform.
Actually, from UFS host side, 1ms-5ms delay is already sufficient for its
initialization of the local UIC layer.
Fixes: 7a3e97b0dc ([SCSI] ufshcd: UFS Host controller driver)
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A null check before a kfree is redundant, so remove it. This is detected
by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding the command and kicking the virtqueue so far was done one after
another. Make the kick optional, so that we can take into account
SCMD_LAST. We also need a commit_rqs callback to kick the device if
blk-mq aborts the submission before the last request is reached.
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This allows a list of requests to be issued, with the LLD only writing the
hardware doorbell when necessary, after the last request was prepared.
This is more efficient if we have lists of requests to issue, particularly
on virtualized hardware, where writing the doorbell is more expensive than
on real hardware.
The use case for this is plugged IO, where blk-mq flushes a batch of
requests all at once.
The API is the same as for blk-mq, just with blk-mq concepts tweaked to
fit the SCSI subsystem API: the "last" flag in blk_mq_queue_data becomes a
flag in scsi_cmnd, while the queue_num in the commit_rqs callback is
extracted from the hctx and passed as a parameter.
The only complication is that blk-mq uses different plugging heuristics
depending on whether commit_rqs is present or not. So we have two
different sets of blk_mq_ops and pick one depending on whether the
scsi_host template uses commit_rqs or not.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently only "interrupt-based" errors have their own history, however
there are some "non-interrupt-based" errors or events which need history
to improve debugging or help know the health status of UFS devices.
Example of fatal errors:
- Link startup error
- Suspend error
- Resume error
Example of abnormal events:
- Task or request abort
- Device reset (now equals to Logical Unit Reset)
- Host reset
This patch tries to track above errors and events by existed UFS error
history mechanism.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently UFS error history will be reset and lost during host reset flow
by ufschd_probe_hba().
Avoid resetting it so error history can be kept as complete as possible to
improve debugging.
In addition, fix a minor display error in ufshcd_print_err_hist().
[mkp: commit desc clarification]
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide more information about fatal and auto-hibern8 errors to improve
debugging by extending existing UFS error history framework.
[mkp: typos]
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove "uic" term in below error history functions and structures for more
general usages,
struct ufs_uic_err_reg_hist;
void ufshcd_update_uic_reg_hist(struct ufs_uic_err_reg_hist *reg_hist,
u32 reg);
void ufshcd_print_uic_err_hist(struct ufs_hba *hba,
struct ufs_uic)err_reg_hist *err_hist, char *err_name);
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note
is adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXTJS/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQTNAQCsTdkA
IN1BvDBbE+KO8mvL5DuRxLtnDU6Pq5K6fkrE3gD/a1GkqyPPaJIuspq7fQY87DH/
o7VsJd/5uGphIE2Ls+M=
=38XV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note is
adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: megaraid_sas: set an unlimited max_segment_size
scsi: mpt3sas: set an unlimited max_segment_size for SAS 3.0 HBAs
scsi: IB/srp: set virt_boundary_mask in the scsi host
scsi: IB/iser: set virt_boundary_mask in the scsi host
scsi: storvsc: set virt_boundary_mask in the scsi host template
scsi: ufshcd: set max_segment_size in the scsi host template
scsi: core: take the DMA max mapping size into account
scsi: core: add a host / host template field for the virt boundary
scsi: core: Fix race on creating sense cache
scsi: sd_zbc: Fix compilation warning
scsi: libfc: fix null pointer dereference on a null lport
scsi: zfcp: fix GCC compiler warning emitted with -Wmaybe-uninitialized
scsi: zfcp: fix request object use-after-free in send path causing wrong traces
scsi: zfcp: fix request object use-after-free in send path causing seqno errors
scsi: megaraid_sas: Update driver version to 07.710.50.00
scsi: megaraid_sas: Add module parameter for FW Async event logging
scsi: megaraid_sas: Enable msix_load_balance for Invader and later controllers
scsi: megaraid_sas: Fix calculation of target ID
scsi: lpfc: reduce stack size with CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE
scsi: devinfo: BLIST_TRY_VPD_PAGES for SanDisk Cruzer Blade
...
- match the directory structure of the linux-libc-dev package to that of
Debian-based distributions
- fix incorrect include/config/auto.conf generation when Kconfig creates
it along with the .config file
- remove misleading $(AS) from documents
- clean up precious tag files by distclean instead of mrproper
- add a new coccinelle patch for devm_platform_ioremap_resource migration
- refactor module-related scripts to read modules.order instead of
$(MODVERDIR)/*.mod files to get the list of created modules
- remove MODVERDIR
- update list of header compile-test
- add -fcf-protection=none flag to avoid conflict with the retpoline
flags when CONFIG_RETPOLINE=y
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=D36u
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- match the directory structure of the linux-libc-dev package to that
of Debian-based distributions
- fix incorrect include/config/auto.conf generation when Kconfig
creates it along with the .config file
- remove misleading $(AS) from documents
- clean up precious tag files by distclean instead of mrproper
- add a new coccinelle patch for devm_platform_ioremap_resource
migration
- refactor module-related scripts to read modules.order instead of
$(MODVERDIR)/*.mod files to get the list of created modules
- remove MODVERDIR
- update list of header compile-test
- add -fcf-protection=none flag to avoid conflict with the retpoline
flags when CONFIG_RETPOLINE=y
- misc cleanups
* tag 'kbuild-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
kbuild: add -fcf-protection=none when using retpoline flags
kbuild: update compile-test header list for v5.3-rc1
kbuild: split out *.mod out of {single,multi}-used-m rules
kbuild: remove 'prepare1' target
kbuild: remove the first line of *.mod files
kbuild: create *.mod with full directory path and remove MODVERDIR
kbuild: export_report: read modules.order instead of .tmp_versions/*.mod
kbuild: modpost: read modules.order instead of $(MODVERDIR)/*.mod
kbuild: modsign: read modules.order instead of $(MODVERDIR)/*.mod
kbuild: modinst: read modules.order instead of $(MODVERDIR)/*.mod
scsi: remove pointless $(MODVERDIR)/$(obj)/53c700.ver
kbuild: remove duplication from modules.order in sub-directories
kbuild: get rid of kernel/ prefix from in-tree modules.{order,builtin}
kbuild: do not create empty modules.order in the prepare stage
coccinelle: api: add devm_platform_ioremap_resource script
kbuild: compile-test headers listed in header-test-m as well
kbuild: remove unused hostcc-option
kbuild: remove tag files by distclean instead of mrproper
kbuild: add --hash-style= and --build-id unconditionally
kbuild: get rid of misleading $(AS) from documents
...
Pull vfs mount updates from Al Viro:
"The first part of mount updates.
Convert filesystems to use the new mount API"
* 'work.mount0' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
mnt_init(): call shmem_init() unconditionally
constify ksys_mount() string arguments
don't bother with registering rootfs
init_rootfs(): don't bother with init_ramfs_fs()
vfs: Convert smackfs to use the new mount API
vfs: Convert selinuxfs to use the new mount API
vfs: Convert securityfs to use the new mount API
vfs: Convert apparmorfs to use the new mount API
vfs: Convert openpromfs to use the new mount API
vfs: Convert xenfs to use the new mount API
vfs: Convert gadgetfs to use the new mount API
vfs: Convert oprofilefs to use the new mount API
vfs: Convert ibmasmfs to use the new mount API
vfs: Convert qib_fs/ipathfs to use the new mount API
vfs: Convert efivarfs to use the new mount API
vfs: Convert configfs to use the new mount API
vfs: Convert binfmt_misc to use the new mount API
convenience helper: get_tree_single()
convenience helper get_tree_nodev()
vfs: Kill sget_userns()
...
new iommu device
vhost guest memory access using vmap (just meta-data for now)
minor fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Note: due to code driver changes the driver-core tree, the following
patch is needed when merging tree with commit 92ce7e83b4
("driver_find_device: Unify the match function with
class_find_device()") in the driver-core tree:
From: Nathan Chancellor <natechancellor@gmail.com>
Subject: [PATCH] iommu/virtio: Constify data parameter in viommu_match_node
After commit 92ce7e83b4 ("driver_find_device: Unify the match
function with class_find_device()") in the driver-core tree.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
---
drivers/iommu/virtio-iommu.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/iommu/virtio-iommu.c b/drivers/iommu/virtio-iommu.c
index 4620dd221ffd..433f4d2ee956 100644
--- a/drivers/iommu/virtio-iommu.c
+++ b/drivers/iommu/virtio-iommu.c
@@ -839,7 +839,7 @@ static void viommu_put_resv_regions(struct device *dev, struct list_head *head)
static struct iommu_ops viommu_ops;
static struct virtio_driver virtio_iommu_drv;
-static int viommu_match_node(struct device *dev, void *data)
+static int viommu_match_node(struct device *dev, const void *data)
{
return dev->parent->fwnode == data;
}
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJdJ5qUAAoJECgfDbjSjVRpQs0H/2qWcIG1zjGKyh9KWrfgOusG
/QIqeP50d7SC6oqdyd00tzmExqO1xdGLPFzYixdOsU817te1gHBP4Rfmzo01jZRd
CUzZNnZQ2JRsDshiA6G2ui+wn1/a/cB3RPN4rT1mquDYS53QmsRGDQDnpp84TXMV
aocB8TS6halbRzKMq3VmaWHIvzNXnt4dwQR542+PyeLLn9bUx2QwWj2ON3QwxixK
dVRZow3GwLGBhKTA/Z1Z/Bta4fEfOKjUGP2XWgvL6zOr+nZR4eQ8w5WXVJYzR+d6
1JCfqTxleweT2k6Tu5VwtTNlQkxn/XvQAeisppOiEE6NnPjubyI9wMQIvL7bkpo=
=uJbC
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio, vhost updates from Michael Tsirkin:
"Fixes, features, performance:
- new iommu device
- vhost guest memory access using vmap (just meta-data for now)
- minor fixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-mmio: add error check for platform_get_irq
scsi: virtio_scsi: Use struct_size() helper
iommu/virtio: Add event queue
iommu/virtio: Add probe request
iommu: Add virtio-iommu driver
PCI: OF: Initialize dev->fwnode appropriately
of: Allow the iommu-map property to omit untranslated devices
dt-bindings: virtio: Add virtio-pci-iommu node
dt-bindings: virtio-mmio: Add IOMMU description
vhost: fix clang build warning
vhost: access vq metadata through kernel virtual address
vhost: factor out setting vring addr and num
vhost: introduce helpers to get the size of metadata area
vhost: rename vq_iotlb_prefetch() to vq_meta_prefetch()
vhost: fine grain userspace memory accessors
vhost: generalize adding used elem
Some files got renamed but probably due to some merge conflicts,
a few references still point to the old locations.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When using a virt_boundary_mask, as done for NVMe devices attached to
megaraid_sas controllers, we require an unlimited max_segment_size as the
virt boundary merging code assumes that. But we also need to propagate
that to the DMA mapping layer to make dma-debug happy. The SCSI layer
takes care of that when using the per-host virt_boundary setting, but
given that megaraid_sas only wants to set the virt_boundary for actual
NVMe devices, we can't rely on that. The DMA layer maximum segment is
global to the HBA however, so we have to set it explicitly. This patch
assumes that megaraid_sas does not have a segment size limitation, which
seems true based on the SGL format, but will need to be verified.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When using a virt_boundary_mask, as done for NVMe devices attached to
mpt3sas controllers, we require an unlimited max_segment_size as the virt
boundary merging code assumes that. But we also need to propagate that to
the DMA mapping layer to make dma-debug happy. The SCSI layer takes care
of that when using the per-host virt_boundary setting, but given that
mpt3sas only wants to set the virt_boundary for actual NVMe devices, we
can't rely on that. The DMA layer maximum segment is global to the HBA
however, so we have to set it explicitly. This patch assumes that mpt3sas
does not have a segment size limitation, which seems true based on the SGL
format, but will need to be verified.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This ensures all proper DMA layer handling is taken care of by the SCSI
midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need to also mirror the value to the device to ensure IOMMU merging
doesn't undo it, and the SCSI host level parameter will ensure that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need to limit the device's max_sectors to what the DMA mapping
implementation can support. If not, we risk running out of swiotlb
buffers easily.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This allows drivers setting it up easily instead of branching out to block
layer calls in slave_alloc, and ensures the upgraded max_segment_size
setting gets picked up by the DMA layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Kashyap Desai < kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When scsi_init_sense_cache(host) is called concurrently from different
hosts, each code path may find that no cache has been created and
allocate a new one. The lack of locking can lead to potentially
overriding a cache allocated by a different host.
Fix the issue by moving 'mutex_lock(&scsi_sense_cache_mutex)' before
scsi_select_sense_cache().
Fixes: 0a6ac4ee7c ("scsi: respect unchecked_isa_dma for blk-mq")
Cc: Stable <stable@vger.kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
kbuild test robot gets the following compilation warning using gcc 7.4
cross compilation for c6x (GCC_VERSION=7.4.0 make.cross ARCH=c6x).
In file included from include/asm-generic/bug.h:18:0,
from arch/c6x/include/asm/bug.h:12,
from include/linux/bug.h:5,
from include/linux/thread_info.h:12,
from include/asm-generic/current.h:5,
from ./arch/c6x/include/generated/asm/current.h:1,
from include/linux/sched.h:12,
from include/linux/blkdev.h:5,
from drivers//scsi/sd_zbc.c:11:
drivers//scsi/sd_zbc.c: In function 'sd_zbc_read_zones':
>> include/linux/kernel.h:62:48: warning: 'zone_blocks' may be used
uninitialized in this function [-Wmaybe-uninitialized]
#define __round_mask(x, y) ((__typeof__(x))((y)-1))
^
drivers//scsi/sd_zbc.c:464:6: note: 'zone_blocks' was declared here
u32 zone_blocks;
^~~~~~~~~~~
This is a false-positive report. The variable zone_blocks is always
initialized in sd_zbc_check_zones() before use. It is not initialized
only and only if sd_zbc_check_zones() fails.
Avoid this warning by initializing the zone_blocks variable to 0.
Fixes: 5f832a3958 ("scsi: sd_zbc: Fix sd_zbc_check_zones() error checks")
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if lport is null then the null lport pointer is dereference when
printing out debug via the FC_LPORT_DB macro. Fix this by using the more
generic FC_LIBFC_DBG debug macro instead that does not use lport.
Addresses-Coverity: ("Dereference after null check")
Fixes: 7414705ea4 ("libfc: Add runtime debugging with debug_logging module parameter")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----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=g8xI
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190715' of git://git.kernel.dk/linux-block
Pull more block updates from Jens Axboe:
"A later pull request with some followup items. I had some vacation
coming up to the merge window, so certain things items were delayed a
bit. This pull request also contains fixes that came in within the
last few days of the merge window, which I didn't want to push right
before sending you a pull request.
This contains:
- NVMe pull request, mostly fixes, but also a few minor items on the
feature side that were timing constrained (Christoph et al)
- Report zones fixes (Damien)
- Removal of dead code (Damien)
- Turn on cgroup psi memstall (Josef)
- block cgroup MAINTAINERS entry (Konstantin)
- Flush init fix (Josef)
- blk-throttle low iops timing fix (Konstantin)
- nbd resize fixes (Mike)
- nbd 0 blocksize crash fix (Xiubo)
- block integrity error leak fix (Wenwen)
- blk-cgroup writeback and priority inheritance fixes (Tejun)"
* tag 'for-linus-20190715' of git://git.kernel.dk/linux-block: (42 commits)
MAINTAINERS: add entry for block io cgroup
null_blk: fixup ->report_zones() for !CONFIG_BLK_DEV_ZONED
block: Limit zone array allocation size
sd_zbc: Fix report zones buffer allocation
block: Kill gfp_t argument of blkdev_report_zones()
block: Allow mapping of vmalloc-ed buffers
block/bio-integrity: fix a memory leak bug
nvme: fix NULL deref for fabrics options
nbd: add netlink reconfigure resize support
nbd: fix crash when the blksize is zero
block: Disable write plugging for zoned block devices
block: Fix elevator name declaration
block: Remove unused definitions
nvme: fix regression upon hot device removal and insertion
blk-throttle: fix zero wait time for iops throttled group
block: Fix potential overflow in blk_report_zones()
blkcg: implement REQ_CGROUP_PUNT
blkcg, writeback: Implement wbc_blkcg_css()
blkcg, writeback: Add wbc->no_cgroup_owner
blkcg, writeback: Rename wbc_account_io() to wbc_account_cgroup_owner()
...
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Merge updates from Andrew Morton:
"Am experimenting with splitting MM up into identifiable subsystems
perhaps with a view to gitifying it in complex ways. Also with more
verbose "incoming" emails.
Most of MM is here and a few other trees.
Subsystems affected by this patch series:
- hotfixes
- iommu
- scripts
- arch/sh
- ocfs2
- mm:slab-generic
- mm:slub
- mm:kmemleak
- mm:kasan
- mm:cleanups
- mm:debug
- mm:pagecache
- mm:swap
- mm:memcg
- mm:gup
- mm:pagemap
- mm:infrastructure
- mm:vmalloc
- mm:initialization
- mm:pagealloc
- mm:vmscan
- mm:tools
- mm:proc
- mm:ras
- mm:oom-kill
hotfixes:
mm: vmscan: scan anonymous pages on file refaults
mm/nvdimm: add is_ioremap_addr and use that to check ioremap address
mm/memcontrol: fix wrong statistics in memory.stat
mm/z3fold.c: lock z3fold page before __SetPageMovable()
nilfs2: do not use unexported cpu_to_le32()/le32_to_cpu() in uapi header
MAINTAINERS: nilfs2: update email address
iommu:
include/linux/dmar.h: replace single-char identifiers in macros
scripts:
scripts/decode_stacktrace: match basepath using shell prefix operator, not regex
scripts/decode_stacktrace: look for modules with .ko.debug extension
scripts/spelling.txt: drop "sepc" from the misspelling list
scripts/spelling.txt: add spelling fix for prohibited
scripts/decode_stacktrace: Accept dash/underscore in modules
scripts/spelling.txt: add more spellings to spelling.txt
arch/sh:
arch/sh/configs/sdk7786_defconfig: remove CONFIG_LOGFS
sh: config: remove left-over BACKLIGHT_LCD_SUPPORT
sh: prevent warnings when using iounmap
ocfs2:
fs: ocfs: fix spelling mistake "hearbeating" -> "heartbeat"
ocfs2/dlm: use struct_size() helper
ocfs2: add last unlock times in locking_state
ocfs2: add locking filter debugfs file
ocfs2: add first lock wait time in locking_state
ocfs: no need to check return value of debugfs_create functions
fs/ocfs2/dlmglue.c: unneeded variable: "status"
ocfs2: use kmemdup rather than duplicating its implementation
mm:slab-generic:
Patch series "mm/slab: Improved sanity checking":
mm/slab: validate cache membership under freelist hardening
mm/slab: sanity-check page type when looking up cache
lkdtm/heap: add tests for freelist hardening
mm:slub:
mm/slub.c: avoid double string traverse in kmem_cache_flags()
slub: don't panic for memcg kmem cache creation failure
mm:kmemleak:
mm/kmemleak.c: fix check for softirq context
mm/kmemleak.c: change error at _write when kmemleak is disabled
docs: kmemleak: add more documentation details
mm:kasan:
mm/kasan: print frame description for stack bugs
Patch series "Bitops instrumentation for KASAN", v5:
lib/test_kasan: add bitops tests
x86: use static_cpu_has in uaccess region to avoid instrumentation
asm-generic, x86: add bitops instrumentation for KASAN
Patch series "mm/kasan: Add object validation in ksize()", v3:
mm/kasan: introduce __kasan_check_{read,write}
mm/kasan: change kasan_check_{read,write} to return boolean
lib/test_kasan: Add test for double-kzfree detection
mm/slab: refactor common ksize KASAN logic into slab_common.c
mm/kasan: add object validation in ksize()
mm:cleanups:
include/linux/pfn_t.h: remove pfn_t_to_virt()
Patch series "remove ARCH_SELECT_MEMORY_MODEL where it has no effect":
arm: remove ARCH_SELECT_MEMORY_MODEL
s390: remove ARCH_SELECT_MEMORY_MODEL
sparc: remove ARCH_SELECT_MEMORY_MODEL
mm/gup.c: make follow_page_mask() static
mm/memory.c: trivial clean up in insert_page()
mm: make !CONFIG_HUGE_PAGE wrappers into static inlines
include/linux/mm_types.h: ifdef struct vm_area_struct::swap_readahead_info
mm: remove the account_page_dirtied export
mm/page_isolation.c: change the prototype of undo_isolate_page_range()
include/linux/vmpressure.h: use spinlock_t instead of struct spinlock
mm: remove the exporting of totalram_pages
include/linux/pagemap.h: document trylock_page() return value
mm:debug:
mm/failslab.c: by default, do not fail allocations with direct reclaim only
Patch series "debug_pagealloc improvements":
mm, debug_pagelloc: use static keys to enable debugging
mm, page_alloc: more extensive free page checking with debug_pagealloc
mm, debug_pagealloc: use a page type instead of page_ext flag
mm:pagecache:
Patch series "fix filler_t callback type mismatches", v2:
mm/filemap.c: fix an overly long line in read_cache_page
mm/filemap: don't cast ->readpage to filler_t for do_read_cache_page
jffs2: pass the correct prototype to read_cache_page
9p: pass the correct prototype to read_cache_page
mm/filemap.c: correct the comment about VM_FAULT_RETRY
mm:swap:
mm, swap: fix race between swapoff and some swap operations
mm/swap_state.c: simplify total_swapcache_pages() with get_swap_device()
mm, swap: use rbtree for swap_extent
mm/mincore.c: fix race between swapoff and mincore
mm:memcg:
memcg, oom: no oom-kill for __GFP_RETRY_MAYFAIL
memcg, fsnotify: no oom-kill for remote memcg charging
mm, memcg: introduce memory.events.local
mm: memcontrol: dump memory.stat during cgroup OOM
Patch series "mm: reparent slab memory on cgroup removal", v7:
mm: memcg/slab: postpone kmem_cache memcg pointer initialization to memcg_link_cache()
mm: memcg/slab: rename slab delayed deactivation functions and fields
mm: memcg/slab: generalize postponed non-root kmem_cache deactivation
mm: memcg/slab: introduce __memcg_kmem_uncharge_memcg()
mm: memcg/slab: unify SLAB and SLUB page accounting
mm: memcg/slab: don't check the dying flag on kmem_cache creation
mm: memcg/slab: synchronize access to kmem_cache dying flag using a spinlock
mm: memcg/slab: rework non-root kmem_cache lifecycle management
mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages
mm: memcg/slab: reparent memcg kmem_caches on cgroup removal
mm, memcg: add a memcg_slabinfo debugfs file
mm:gup:
Patch series "switch the remaining architectures to use generic GUP", v4:
mm: use untagged_addr() for get_user_pages_fast addresses
mm: simplify gup_fast_permitted
mm: lift the x86_32 PAE version of gup_get_pte to common code
MIPS: use the generic get_user_pages_fast code
sh: add the missing pud_page definition
sh: use the generic get_user_pages_fast code
sparc64: add the missing pgd_page definition
sparc64: define untagged_addr()
sparc64: use the generic get_user_pages_fast code
mm: rename CONFIG_HAVE_GENERIC_GUP to CONFIG_HAVE_FAST_GUP
mm: reorder code blocks in gup.c
mm: consolidate the get_user_pages* implementations
mm: validate get_user_pages_fast flags
mm: move the powerpc hugepd code to mm/gup.c
mm: switch gup_hugepte to use try_get_compound_head
mm: mark the page referenced in gup_hugepte
mm/gup: speed up check_and_migrate_cma_pages() on huge page
mm/gup.c: remove some BUG_ONs from get_gate_page()
mm/gup.c: mark undo_dev_pagemap as __maybe_unused
mm:pagemap:
asm-generic, x86: introduce generic pte_{alloc,free}_one[_kernel]
alpha: switch to generic version of pte allocation
arm: switch to generic version of pte allocation
arm64: switch to generic version of pte allocation
csky: switch to generic version of pte allocation
m68k: sun3: switch to generic version of pte allocation
mips: switch to generic version of pte allocation
nds32: switch to generic version of pte allocation
nios2: switch to generic version of pte allocation
parisc: switch to generic version of pte allocation
riscv: switch to generic version of pte allocation
um: switch to generic version of pte allocation
unicore32: switch to generic version of pte allocation
mm/pgtable: drop pgtable_t variable from pte_fn_t functions
mm/memory.c: fail when offset == num in first check of __vm_map_pages()
mm:infrastructure:
mm/mmu_notifier: use hlist_add_head_rcu()
mm:vmalloc:
Patch series "Some cleanups for the KVA/vmalloc", v5:
mm/vmalloc.c: remove "node" argument
mm/vmalloc.c: preload a CPU with one object for split purpose
mm/vmalloc.c: get rid of one single unlink_va() when merge
mm/vmalloc.c: switch to WARN_ON() and move it under unlink_va()
mm/vmalloc.c: spelling> s/informaion/information/
mm:initialization:
mm/large system hash: use vmalloc for size > MAX_ORDER when !hashdist
mm/large system hash: clear hashdist when only one node with memory is booted
mm:pagealloc:
arm64: move jump_label_init() before parse_early_param()
Patch series "add init_on_alloc/init_on_free boot options", v10:
mm: security: introduce init_on_alloc=1 and init_on_free=1 boot options
mm: init: report memory auto-initialization features at boot time
mm:vmscan:
mm: vmscan: remove double slab pressure by inc'ing sc->nr_scanned
mm: vmscan: correct some vmscan counters for THP swapout
mm:tools:
tools/vm/slabinfo: order command line options
tools/vm/slabinfo: add partial slab listing to -X
tools/vm/slabinfo: add option to sort by partial slabs
tools/vm/slabinfo: add sorting info to help menu
mm:proc:
proc: use down_read_killable mmap_sem for /proc/pid/maps
proc: use down_read_killable mmap_sem for /proc/pid/smaps_rollup
proc: use down_read_killable mmap_sem for /proc/pid/pagemap
proc: use down_read_killable mmap_sem for /proc/pid/clear_refs
proc: use down_read_killable mmap_sem for /proc/pid/map_files
mm: use down_read_killable for locking mmap_sem in access_remote_vm
mm: smaps: split PSS into components
mm: vmalloc: show number of vmalloc pages in /proc/meminfo
mm:ras:
mm/memory-failure.c: clarify error message
mm:oom-kill:
mm: memcontrol: use CSS_TASK_ITER_PROCS at mem_cgroup_scan_tasks()
mm, oom: refactor dump_tasks for memcg OOMs
mm, oom: remove redundant task_in_mem_cgroup() check
oom: decouple mems_allowed from oom_unkillable_task
mm/oom_kill.c: remove redundant OOM score normalization in select_bad_process()"
* akpm: (147 commits)
mm/oom_kill.c: remove redundant OOM score normalization in select_bad_process()
oom: decouple mems_allowed from oom_unkillable_task
mm, oom: remove redundant task_in_mem_cgroup() check
mm, oom: refactor dump_tasks for memcg OOMs
mm: memcontrol: use CSS_TASK_ITER_PROCS at mem_cgroup_scan_tasks()
mm/memory-failure.c: clarify error message
mm: vmalloc: show number of vmalloc pages in /proc/meminfo
mm: smaps: split PSS into components
mm: use down_read_killable for locking mmap_sem in access_remote_vm
proc: use down_read_killable mmap_sem for /proc/pid/map_files
proc: use down_read_killable mmap_sem for /proc/pid/clear_refs
proc: use down_read_killable mmap_sem for /proc/pid/pagemap
proc: use down_read_killable mmap_sem for /proc/pid/smaps_rollup
proc: use down_read_killable mmap_sem for /proc/pid/maps
tools/vm/slabinfo: add sorting info to help menu
tools/vm/slabinfo: add option to sort by partial slabs
tools/vm/slabinfo: add partial slab listing to -X
tools/vm/slabinfo: order command line options
mm: vmscan: correct some vmscan counters for THP swapout
mm: vmscan: remove double slab pressure by inc'ing sc->nr_scanned
...
The RISC-V architecture has a register named the "Supervisor Exception
Program Counter", or "sepc". This abbreviation triggers checkpatch.pl's
misspelling detector, resulting in noise in the checkpatch output. The
risk that this noise could cause more useful warnings to be missed seems
to outweigh the harm of an occasional misspelling of "spec". Thus drop
the "sepc" entry from the misspelling list.
[akpm@linux-foundation.org: fix existing "sepc" instances, per Joe]
Link: http://lkml.kernel.org/r/20190518210037.13674-1-paul.walmsley@sifive.com
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During disk scan and revalidation done with sd_revalidate(), the zones
of a zoned disk are checked using the helper function
blk_revalidate_disk_zones() if a configuration change is detected
(change in the number of zones or zone size). The function
blk_revalidate_disk_zones() issues report_zones calls that are very
large, that is, to obtain zone information for all zones of the disk
with a single command. The size of the report zones command buffer
necessary for such large request generally is lower than the disk
max_hw_sectors and KMALLOC_MAX_SIZE (4MB) and succeeds on boot (no
memory fragmentation), but often fail at run time (e.g. hot-plug
event). This causes the disk revalidation to fail and the disk
capacity to be changed to 0.
This problem can be avoided by using vmalloc() instead of kmalloc() for
the buffer allocation. To limit the amount of memory to be allocated,
this patch also introduces the arbitrary SD_ZBC_REPORT_MAX_ZONES
maximum number of zones to report with a single report zones command.
This limit may be lowered further to satisfy the disk max_hw_sectors
limit. Finally, to ensure that the vmalloc-ed buffer can always be
mapped in a request, the buffer size is further limited to at most
queue_max_segments() pages, allowing successful mapping of the buffer
even in the worst case scenario where none of the buffer pages are
contiguous.
Fixes: 515ce60613 ("scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation")
Fixes: e76239a374 ("block: add a report_zones method")
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only GFP_KERNEL and GFP_NOIO are used with blkdev_report_zones(). In
preparation of using vmalloc() for large report buffer and zone array
allocations used by this function, remove its "gfp_t gfp_mask" argument
and rely on the caller context to use memalloc_noio_save/restore() where
necessary (block layer zone revalidation and dm-zoned I/O error path).
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add module parameter to control logging levels of async event
notifications from firmware that get logged to system log. Also, allow
changing the value from sysfs after driver load.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Load balancing IO completions across all available MSI-X vectors should be
enabled for Invader and later generation controllers only. This needs to
be disabled for older controllers. Add an adapter type check before
setting msix_load_balance flag.
Fixes: 1d15d9098a ("scsi: megaraid_sas: Load balance completions across all MSI-X")
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In megasas_get_target_prop(), driver is incorrectly calculating the target
ID for devices with channel 1 and 3. Due to this, firmware will either
fail the command (if there is no device with the target id sent from
driver) or could return the properties for a target which was not
intended. Devices could end up with the wrong queue depth due to this.
Fix target id calculation for channel 1 and 3.
Fixes: 96188a89cc ("scsi: megaraid_sas: NVME interface target prop added")
Cc: stable@vger.kernel.org
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc_debug_dump_all_queues() function repeatedly calls into
lpfc_debug_dump_qe() which has a temporary 128 byte buffer. This was fine
before the introduction of CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE because
each instance could occupy the same stack slot. However, now they each get
their own copy, which leads to a huge increase in stack usage as seen from
the compiler warning:
drivers/scsi/lpfc/lpfc_debugfs.c: In function 'lpfc_debug_dump_all_queues':
drivers/scsi/lpfc/lpfc_debugfs.c:6474:1: error: the frame size of 1712 bytes is larger than 100 bytes [-Werror=frame-larger-than=]
Avoid this by not marking lpfc_debug_dump_qe() as inline so the compiler
can choose to emit a static version of this function when it's needed or
otherwise silently drop it. As an added benefit, not inlining multiple
copies of this function means we save several kilobytes of .text section,
reducing the file size from 47kb to 43.
It is somewhat unusual to have a function that is static but not inline in
a header file, but this does not cause problems here because it is only
used by other inline functions. It would however seem reasonable to move
all the lpfc_debug_dump_* functions into lpfc_debugfs.c and not mark them
inline as a later cleanup.
Fixes: 81a56f6dcd ("gcc-plugins: structleak: Generalize to all variable types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, all USB devices skip VPD pages, even when the device supports
them (SPC-3 and later), but some of them support VPD, like Cruzer Blade.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Disabling the SATA drive interface cause kernel panic. When the drive
Interface is disabled, device should be deregistered after aborting all
pending I/Os. Also changed the port recovery timeout to 10000 ms for
PM8006 controller.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function sas_wait_eh is declared static and marked EXPORT_SYMBOL, which
is at best an odd combination. Because the function is not used outside of
the drivers/scsi/libsas/sas_scsi_host.c file it is defined in, this commit
removes the EXPORT_SYMBOL() marking.
Signed-off-by: Denis Efremov <efremov@linux.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/megaraid/megaraid_sas_base.c:271:1: warning: symbol 'megasas_issue_dcmd' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_base.c:2227:6: warning: symbol 'megasas_do_ocr' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_base.c:3194:25: warning: symbol 'megaraid_host_attrs' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With a possibly faulty disk the following messages may appear in the logs:
kernel: sd 0:0:9:0: timing out command, waited 180s
kernel: sd 0:0:9:0: timing out command, waited 20s
kernel: sd 0:0:9:0: timing out command, waited 20s
kernel: sd 0:0:9:0: timing out command, waited 60s
kernel: sd 0:0:9:0: timing out command, waited 20s
This is not very informative because it's not possible to identify the
command that timed out.
This patch replaces sdev_printk() with scmd_printk().
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list. This necessitates a large number of driver
changes because the previous guarantee that if a driver specified
SG_ALL as the size of its scatter list, it would get a non-chained
list and didn't need to bother with scatterlist iterators is now
broken and every driver *must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTzzCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZB+AP9I8j/s
wWfg0Z3WNuf4D5I3rH4x1J3cQTqPJed+RjwgcQEA1gZvtOTg1ZEn/CYMVnaB92x0
t6MZSchIaFXeqfD+E7U=
=cv8o
-----END PGP SIGNATURE-----
Merge tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI scatter-gather list updates from James Bottomley:
"This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list.
This necessitates a large number of driver changes because the
previous guarantee that if a driver specified SG_ALL as the size of
its scatter list, it would get a non-chained list and didn't need to
bother with scatterlist iterators is now broken and every driver
*must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase"
* tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
scsi: core: don't preallocate small SGL in case of NO_SG_CHAIN
scsi: lib/sg_pool.c: clear 'first_chunk' in case of no preallocation
scsi: core: avoid preallocating big SGL for data
scsi: core: avoid preallocating big SGL for protection information
scsi: lib/sg_pool.c: improve APIs for allocating sg pool
scsi: esp: use sg helper to iterate over scatterlist
scsi: NCR5380: use sg helper to iterate over scatterlist
scsi: wd33c93: use sg helper to iterate over scatterlist
scsi: ppa: use sg helper to iterate over scatterlist
scsi: pcmcia: nsp_cs: use sg helper to iterate over scatterlist
scsi: imm: use sg helper to iterate over scatterlist
scsi: aha152x: use sg helper to iterate over scatterlist
scsi: s390: zfcp_fc: use sg helper to iterate over scatterlist
scsi: staging: unisys: visorhba: use sg helper to iterate over scatterlist
scsi: usb: image: microtek: use sg helper to iterate over scatterlist
scsi: pmcraid: use sg helper to iterate over scatterlist
scsi: ipr: use sg helper to iterate over scatterlist
scsi: mvumi: use sg helper to iterate over scatterlist
scsi: lpfc: use sg helper to iterate over scatterlist
scsi: advansys: use sg helper to iterate over scatterlist
...
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct virtio_scsi {
...
struct virtio_scsi_vq req_vqs[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(*vscsi) + sizeof(vscsi->req_vqs[0]) * num_queues
with:
struct_size(vscsi, req_vqs, num_queues)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
-----BEGIN PGP SIGNATURE-----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=VSYT
-----END PGP SIGNATURE-----
Merge tag 'for-5.3/block-20190708' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main block updates for 5.3. Nothing earth shattering or
major in here, just fixes, additions, and improvements all over the
map. This contains:
- Series of documentation fixes (Bart)
- Optimization of the blk-mq ctx get/put (Bart)
- null_blk removal race condition fix (Bob)
- req/bio_op() cleanups (Chaitanya)
- Series cleaning up the segment accounting, and request/bio mapping
(Christoph)
- Series cleaning up the page getting/putting for bios (Christoph)
- block cgroup cleanups and moving it to where it is used (Christoph)
- block cgroup fixes (Tejun)
- Series of fixes and improvements to bcache, most notably a write
deadlock fix (Coly)
- blk-iolatency STS_AGAIN and accounting fixes (Dennis)
- Series of improvements and fixes to BFQ (Douglas, Paolo)
- debugfs_create() return value check removal for drbd (Greg)
- Use struct_size(), where appropriate (Gustavo)
- Two lighnvm fixes (Heiner, Geert)
- MD fixes, including a read balance and corruption fix (Guoqing,
Marcos, Xiao, Yufen)
- block opal shadow mbr additions (Jonas, Revanth)
- sbitmap compare-and-exhange improvemnts (Pavel)
- Fix for potential bio->bi_size overflow (Ming)
- NVMe pull requests:
- improved PCIe suspent support (Keith Busch)
- error injection support for the admin queue (Akinobu Mita)
- Fibre Channel discovery improvements (James Smart)
- tracing improvements including nvmetc tracing support (Minwoo Im)
- misc fixes and cleanups (Anton Eidelman, Minwoo Im, Chaitanya
Kulkarni)"
- Various little fixes and improvements to drivers and core"
* tag 'for-5.3/block-20190708' of git://git.kernel.dk/linux-block: (153 commits)
blk-iolatency: fix STS_AGAIN handling
block: nr_phys_segments needs to be zero for REQ_OP_WRITE_ZEROES
blk-mq: simplify blk_mq_make_request()
blk-mq: remove blk_mq_put_ctx()
sbitmap: Replace cmpxchg with xchg
block: fix .bi_size overflow
block: sed-opal: check size of shadow mbr
block: sed-opal: ioctl for writing to shadow mbr
block: sed-opal: add ioctl for done-mark of shadow mbr
block: never take page references for ITER_BVEC
direct-io: use bio_release_pages in dio_bio_complete
block_dev: use bio_release_pages in bio_unmap_user
block_dev: use bio_release_pages in blkdev_bio_end_io
iomap: use bio_release_pages in iomap_dio_bio_end_io
block: use bio_release_pages in bio_map_user_iov
block: use bio_release_pages in bio_unmap_user
block: optionally mark pages dirty in bio_release_pages
block: move the BIO_NO_PAGE_REF check into bio_release_pages
block: skd_main.c: Remove call to memset after dma_alloc_coherent
block: mtip32xx: Remove call to memset after dma_alloc_coherent
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Os1seHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGtx4H/j6i482XzcGFKTBm
A7mBoQpy+kLtoUov4EtBAR62OuwI8rsahW9di37QKndPoQrczWaKBmr3De6LCdPe
v3pl3O6wBbvH5ru+qBPFX9PdNbDvimEChh7LHxmMxNQq3M+AjZAZVJyfpoiFnx35
Fbge+LZaH/k8HMwZmkMr5t9Mpkip715qKg2o9Bua6dkH0AqlcpLlC8d9a+HIVw/z
aAsyGSU8jRwhoAOJsE9bJf0acQ/pZSqmFp0rDKqeFTSDMsbDRKLGq/dgv4nW0RiW
s7xqsjb/rdcvirRj3rv9+lcTVkOtEqwk0PVdL9WOf7g4iYrb3SOIZh8ZyViaDSeH
VTS5zps=
=huBY
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc6' into for-5.3/block
Merge 5.2-rc6 into for-5.3/block, so we get the same page merge leak
fix. Otherwise we end up having conflicts with future patches between
for-5.3/block and master that touch this area. In particular, it makes
the bio_full() fix hard to backport to stable.
* tag 'v5.2-rc6': (482 commits)
Linux 5.2-rc6
Revert "iommu/vt-d: Fix lock inversion between iommu->lock and device_domain_lock"
Bluetooth: Fix regression with minimum encryption key size alignment
tcp: refine memory limit test in tcp_fragment()
x86/vdso: Prevent segfaults due to hoisted vclock reads
SUNRPC: Fix a credential refcount leak
Revert "SUNRPC: Declare RPC timers as TIMER_DEFERRABLE"
net :sunrpc :clnt :Fix xps refcount imbalance on the error path
NFS4: Only set creation opendata if O_CREAT
ARM: 8867/1: vdso: pass --be8 to linker if necessary
KVM: nVMX: reorganize initial steps of vmx_set_nested_state
KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries
habanalabs: use u64_to_user_ptr() for reading user pointers
nfsd: replace Jeff by Chuck as nfsd co-maintainer
inet: clear num_timeout reqsk_alloc()
PCI/P2PDMA: Ignore root complex whitelist when an IOMMU is present
net: mvpp2: debugfs: Add pmap to fs dump
ipv6: Default fib6_type to RTN_UNICAST when not set
net: hns3: Fix inconsistent indenting
net/af_iucv: always register net_device notifier
...
One simple fix for a driver use after free.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXRanDiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisheLdAQDqNfwa
zjLaPyTcuvDDyl5l6P1/HwP+wko3Ssan30kb/QEA+1fMxV1FqtwLADP9QVA1OMTc
1E72PEHf7oEaXmRMXfM=
=oJHK
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One simple fix for a driver use after free"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: vmw_pscsi: Fix use-after-free in pvscsi_queue_lck()
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
On session deletion, current qla code would unregister an NVMe session
before flushing IOs. This patch would move the unregistration of NVMe
session after IO flush. This way FC-NVMe layer would not have to wait for
stuck IOs. In addition, qla2xxx would stop accepting new IOs during session
deletion.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch uses kref to protect access between fcp_abort path and nvme
command and LS command completion path. Stack trace below shows the abort
path is accessing stale memory (nvme_private->sp).
When command kref reaches 0, nvme_private & srb resource will be
disconnected from each other. Any subsequence nvme abort request will not
be able to reference the original srb.
[ 5631.003998] BUG: unable to handle kernel paging request at 00000010000005d8
[ 5631.004016] IP: [<ffffffffc087df92>] qla_nvme_abort_work+0x22/0x100 [qla2xxx]
[ 5631.004086] Workqueue: events qla_nvme_abort_work [qla2xxx]
[ 5631.004097] RIP: 0010:[<ffffffffc087df92>] [<ffffffffc087df92>] qla_nvme_abort_work+0x22/0x100 [qla2xxx]
[ 5631.004109] Call Trace:
[ 5631.004115] [<ffffffffaa4b8174>] ? pwq_dec_nr_in_flight+0x64/0xb0
[ 5631.004117] [<ffffffffaa4b9d4f>] process_one_work+0x17f/0x440
[ 5631.004120] [<ffffffffaa4bade6>] worker_thread+0x126/0x3c0
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffc050d10c>] qla_nvme_unregister_remote_port+0x6c/0xf0 [qla2xxx]
PGD 800000084cf41067 PUD 84d288067 PMD 0
Oops: 0000 [#1] SMP
Call Trace:
[<ffffffff98abcfdf>] process_one_work+0x17f/0x440
[<ffffffff98abdca6>] worker_thread+0x126/0x3c0
[<ffffffff98abdb80>] ? manage_workers.isra.26+0x2a0/0x2a0
[<ffffffff98ac4f81>] kthread+0xd1/0xe0
[<ffffffff98ac4eb0>] ? insert_kthread_work+0x40/0x40
[<ffffffff9918ad37>] ret_from_fork_nospec_begin+0x21/0x21
[<ffffffff98ac4eb0>] ? insert_kthread_work+0x40/0x40
RIP [<ffffffffc050d10c>] qla_nvme_unregister_remote_port+0x6c/0xf0 [qla2xxx]
The crash is due to a bad entry in the nvme_rport_list. This list is not
protected, and when a remoteport_delete callback is called, driver
traverses the list and crashes.
Actually, the list could be removed and driver could traverse the main
fcport list instead. Fix does exactly that.
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Aero adapters, driver provides three different performance modes
controlled through module parameter named 'perf_mode'. Below are those
performance modes:
0: Balanced - Additional high IOPS reply queues will be enabled along with
low latency queues. Interrupt coalescing will be enabled only for these
high IOPS reply queues.
1: IOPS - No additional high IOPS queues are enabled. Interrupt coalescing
will be enabled on all reply queues.
2: Latency - No additional high IOPS queues are enabled. Interrupt
coalescing will be disabled on all reply queues. This is a legacy
behavior similar to Ventura & Invader Series.
Default performance mode settings:
- Performance mode set to 'Balanced', if Aero controller is working in
16GT/s PCIe speed.
- Performance mode will be set to 'Latency' mode for all other cases.
Through module parameter 'perf_mode', user can override default performance
mode to desired one.
Captured some performance numbers with these performance modes. 4k Random
Read IO performance numbers on 24 SAS SSD drives for above three
performance modes. Performance data is from Intel Skylake and HGST SS300
(drive model SDLL1DLR400GCCA1).
IOPS:
-----------------------------------------------------------------------
|perf_mode | qd = 1 | qd = 64 | note |
|-------------|--------|---------|-------------------------------------
|balanced | 259K | 3061k | Provides max performance numbers |
| | | | both on lower QD workload & |
| | | | also on higher QD workload |
|-------------|--------|---------|-------------------------------------
|iops | 220K | 3100k | Provides max performance numbers |
| | | | only on higher QD workload. |
|-------------|--------|---------|-------------------------------------
|latency | 246k | 2226k | Provides good performance numbers |
| | | | only on lower QD worklaod. |
-----------------------------------------------------------------------
Average Latency:
-----------------------------------------------------
|perf_mode | qd = 1 | qd = 64 |
|-------------|--------------|----------------------|
|balanced | 92.05 usec | 501.12 usec |
|-------------|--------------|----------------------|
|iops | 108.40 usec | 498.10 usec |
|-------------|--------------|----------------------|
|latency | 97.10 usec | 689.26 usec |
-----------------------------------------------------
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver will use round-robin method for IO submission in batches within
the high IOPS queues when the number of in-flight ios on the target device
is larger than 8. Otherwise the driver will use low latency reply queues.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
High iops queues are mapped to non-managed IRQs. Set affinity of
non-managed irqs to local numa node. Low latency queues are mapped to
managed IRQs.
Driver reserves some reply queues for high IOPS queues (through
pci_alloc_irq_vectors_affinity and .pre_vectors interface). The rest of
queues are for low latency.
Based on IO workload, driver will decide which group of reply queues
(either high IOPS queues or low latency queues) to be used.
High IOPS queues will be mapped to local numa node of controller and
low latency queues will be mapped to CPUs across numa nodes. In general,
high IOPS and low latency queues should fit into 128 reply queues
which is the max number of reply queues supported by Aero adapters.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver should enable interrupt coalescing (during driver load and after
Controller Reset) for High IOPS queues by masking appropriate bits in IOC
INIT frame.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Aero controllers support balanced performance mode through the ability to
configure queues with different properties.
Reply queues with interrupt coalescing enabled are called "high iops reply
queues" and reply queues with interrupt coalescing disabled are called "low
latency reply queues".
The driver configures a combination of high iops and low latency reply
queues if:
- HBA is an AERO controller;
- MSI-X vectors supported by the HBA is 128;
- Total CPU count in the system more than high iops queue count;
- Driver is loaded with default max_msix_vectors module parameter; and
- System booted in non-kdump mode.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added driver support to allow passthrough MPI toolbox type MFI commands to
firmware based on firmware capability.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For RAID5/RAID6 volumes configured behind Aero, driver will be doing 64bit
division operations on behalf of firmware as controller's ARM CPU is very
slow in this division. Later, driver calculates Q-ARM, P-ARM and Log-ARM and
passes those values to firmware by writing these values to RAID_CONTEXT.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
RAID1 PCI bandwidth limit algorithm is not applicable to Aero as it's PCIe
Gen4 adapter.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: This issue is applicable to scenario when JBOD sequence map is
unavailable (memory allocation for JBOD sequence map failed) to driver but
feature is supported by firmware. If the driver sends a JBOD IO by not
adding 255 (MAX_PHYSICAL_DEVICES - 1) to device ID when underlying firmware
supports JBOD sequence map, it will lead to the IO failure.
Fix: For JBOD IOs, driver will not use the RAID map to fetch the devhandle
if JBOD sequence map is unavailable. Driver will set Devhandle to 0xffff
and Target ID to 'device ID + 255 (MAX_PHYSICAL_DEVICES - 1)'.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware does not expect FastPath IO sent through Region Lock Bypass queue.
Though firmware never exposes such settings when fastpath IO can be sent to
RL bypass queue but it's safer to remove dead code which directs fastpath
IO to RL Bypass queue.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: Under certain conditions, controller goes in FAULT state after IOC
INIT fired to firmware. Such Fault can be recovered through controller
reset.
Fix: In driver probe context, if firmware fault is observed post IOC INIT,
driver would do controller reset followed by retry logic for IOC INIT
command.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: There is possibility of few DCMDs timing out with 'reset_mutex' lock
held. As part of DCMD timeout handling, driver calls function
megasas_reset_fusion which also tries to acquire same lock 'reset_mutex'
and end up with deadlock.
Fix: Upon timeout of DCMDs (which are fired with 'reset_mutex' lock held),
driver will release 'reset_mutex' before calling OCR function and will
acquire lock again after OCR function returns.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On PowerPC architecture, calling disable_irq_nosync from IRQ context is not
providing the required effect.
In current megaraid_sas driver, disable_irq_nosync is being called from IRQ
context before enabling IRQ poll. But due to the issue seen on PPC, after
IRQ poll disable and legacy ISR is enabled, we are not seeing our ISR
getting called.
Fix: Call disable_irq from IRQ poll thread context instead of IRQ context.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will add support for non-secure Aero adapter PCI IDs. Driver
will throw an error message when a non-secure type controller is
detected. Purpose of this interface is to avoid interacting with any
firmware which is not secured/signed by Broadcom. Any tampering on Firmware
component will be detected by hardware and it will be communicated to the
driver to avoid any further interaction with that component.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Aero adapters provides Atomic Request Descriptor as an alternative method
for posting an entry onto a request queue. The posting of an Atomic Request
Descriptor is an atomic operation, providing a safe mechanism for multiple
processors on the host to post requests without synchronization. This
Atomic Request Descriptor format is identical to first 32 bits of Default
Request Descriptor and uses only 32 bits.
If Aero adapters support Atomic descriptor, driver should use it for
posting IOs and DCMDs to firmware.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the logic for collecting IOP log respective to event log size.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to read event log size from MPI configuration table and
export through sysfs.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable msix load balance only when combined reply queue mode is disabled on
the SAS3 and above generation HBA devices.
Earlier msix load balance used to enable if the number of online cpus is
greater than the number of MSI-X vectors enabled on the HBA. Combined reply
queue mode will be disabled only on those HBA which works in shared
resources mode. I.e. on SAS3 HBAs it will be <= 8 and on SAS35 HBA devices
it will be <= 16.
- Before this patch if system has 256 logical CPUs and HBA exposes 128
MSI-X vectors, driver will enable msix load balance.
- After this patch if system has 256 logical CPUs and HBA exposes 128
MSI-X vectors, driver will disable msix load balance.
- After this patch if system has 256 logical CPUs and HBA exposes 16 MSI-X
vectors (due to combined reply queue mode being off in HW), driver will
enable msix load balance.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Even though 'smp_affinity_enable' module parameter is enabled, if the
number of online CPUs is bigger than the number of msix vectors enabled on
that HBA, then smp affinity settings should be disabled only for this HBA.
But currently the smp affinity setting is disabled globally and hence smp
affinity will be disabled for subsequent HBAs even though number of msix
vectors enabled for this HBA matches the number of online CPU.
To fix this, define a per HBA variable smp_affinity_enable. Initially this
variable is initialized with smp_affinity_enable module parameter value. If
this HBA has less number of msix vectors configured when compared to number
of online cpus, then only this HBA's variable smp_affinity_enable is set to
zero.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When enabling high iops queues, the driver should use the HBA's configured
PCIe link speed instead of looking for the maximum link speed.
I.e. enable high iops queues only if Aero/Sea HBA's configured PCIe link
speed is set to 16GT/s.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently default perf_mode is set to 'balanced' on Intel architecture
machines and on other machines default perf_mode is set to 'latency' mode.
This CPU architecture check is removed and the default perf_mode mode is
set to 'balanced' mode on all machines.
User can choose the required performance mode using perf_mode module
parameter.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cb_arg alloc failed, we can't release the struct orig_io_req refcount
before we take its refcount. As Saurav said, move the srr_err label down
to avoid unnecessary refcount release and nullptr free.
Signed-off-by: Lin Yi <teroincn@163.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cb_arg alloc failed, we can't release the struct orig_io_req refcount
before we take its refcount. As Saurav said, move the rec_err label down
to avoid unnecessary refcount release and nullptr free.
Signed-off-by: Lin Yi <teroincn@163.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 2.12.10.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Reduce the sg_tablesize to 255.
- Reduce the MAX BDs firmware can handle to 255.
- Return IO to ML if BD goes more then 255 after split.
- Correct the size of each BD split to 0xffff.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If firmware sends either cleanup or abort completion, it means other won't
be sent. Clean out flags for other as well.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Separate out abort and cleanup flag and completion, to have better
understaning of what is getting processed.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In certain tests where the SCSI error handler issues an abort that is
already outstanding, we will cleanup the command so that the SCSI error
handler can proceed. In some of these cases we were seeing a command
mismatch:
kernel: scsi host2: bnx2fc: xid:0x42b eh_abort - refcnt = 2
kernel: bnx2fc: eh_abort: io_req (xid = 0x42b) already in abts processing
kernel: scsi host2: bnx2fc: xid:0x42b Entered bnx2fc_initiate_cleanup
kernel: scsi host2: bnx2fc: xid:0x42b CLEANUP io_req xid = 0x80b
kernel: scsi host2: bnx2fc: xid:0x80b cq_compl- cleanup resp rcvd
kernel: scsi host2: bnx2fc: xid:0x42b complete - rx_state = 9
kernel: scsi host2: bnx2fc: xid:0x42b Entered process_cleanup_compl refcnt = 2, cmd_type = 1
kernel: scsi host2: bnx2fc: xid:0x42b scsi_done. err_code = 0x7
kernel: scsi host2: bnx2fc: xid:0x42b sc=ffff8807f93dfb80, result=0x7, retries=0, allowed=5
kernel: ------------[ cut here ]------------
kernel: WARNING: at /root/rpmbuild/BUILD/netxtreme2-7.14.43/obj/default/bnx2fc-2.12.1/driver/bnx2fc_io.c:1347 bnx2fc_eh_abort+0x56f/0x680 [bnx2fc]()
kernel: xid=0x42b refcount=-1
kernel: Modules linked in:
kernel: nls_utf8 isofs sr_mod cdrom tcp_lp dm_round_robin xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge ebtable_filter ebtables fuse ip6table_filter ip6_tables iptable_filter bnx2fc(OE) cnic(OE) uio fcoe libfcoe 8021q libfc garp mrp scsi_transport_fc stp llc scsi_tgt vfat fat dm_service_time intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd ses enclosure ipmi_ssif i2c_core hpilo hpwdt wmi sg ipmi_devintf pcspkr ipmi_si ipmi_msghandler shpchp acpi_power_meter dm_multipath nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs sd_mod crc_t10dif
kernel: crct10dif_generic bnx2x(OE) crct10dif_pclmul crct10dif_common crc32c_intel mdio ptp pps_core libcrc32c smartpqi scsi_transport_sas fjes uas usb_storage dm_mirror dm_region_hash dm_log dm_mod
kernel: CPU: 9 PID: 2012 Comm: scsi_eh_2 Tainted: G W OE ------------ 3.10.0-514.el7.x86_64 #1
kernel: Hardware name: HPE Synergy 480 Gen10/Synergy 480 Gen10 Compute Module, BIOS I42 03/21/2018
kernel: ffff8807f25a3d98 0000000015e7fa0c ffff8807f25a3d50 ffffffff81685eac
kernel: ffff8807f25a3d88 ffffffff81085820 ffff8807f8e39000 ffff880801ff7468
kernel: ffff880801ff7610 0000000000002002 ffff8807f8e39014 ffff8807f25a3df0
kernel: Call Trace:
kernel: [<ffffffff81685eac>] dump_stack+0x19/0x1b
kernel: [<ffffffff81085820>] warn_slowpath_common+0x70/0xb0
kernel: [<ffffffff810858bc>] warn_slowpath_fmt+0x5c/0x80
kernel: [<ffffffff8168d842>] ? _raw_spin_lock_bh+0x12/0x50
kernel: [<ffffffffa0549e6f>] bnx2fc_eh_abort+0x56f/0x680 [bnx2fc]
kernel: [<ffffffff814570af>] scsi_error_handler+0x59f/0x8b0
kernel: [<ffffffff81456b10>] ? scsi_eh_get_sense+0x250/0x250
kernel: [<ffffffff810b052f>] kthread+0xcf/0xe0
kernel: [<ffffffff810b0460>] ? kthread_create_on_node+0x140/0x140
kernel: [<ffffffff81696418>] ret_from_fork+0x58/0x90
kernel: [<ffffffff810b0460>] ? kthread_create_on_node+0x140/0x140
kernel: ---[ end trace 42deb88f2032b111 ]---
The reason that there was a mismatch is that the SCSI command is actual
returned from the cleanup handler. In previous testing, the type of
cleanup notification we'd get from the CQE did not trigger the code that
returned the SCSI command. To overcome the previous behavior we would put
a reference in bnx2fc_abts_cleanup() to account for the SCSI command.
However, in cases where the SCSI command is actually off, we end up with an
extra put.
The fix for this is to only take the extra put in bnx2fc_abts_cleanup if
the completion for the cleanup times out.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For bnx2fc, the source FCoE MAC is stored in the fcoe_port struct in the
data_src_mac field. Currently this is set in fcoe_ctlr_recv_flogi which
ends up setting it by simply using fc_fcoe_set_mac() which only uses the
default FCF-MAC. We still want to store the source FCoE MAC in
port->data_src_mac but we want to snoop the FLOGI response payload so as to
set it in the following method:
1. If a granted_mac is found, use that.
2. If not granted_mac is there but there is a FCF-MAP from the FCF then
create the MAC from the FCF-MAP and the destination ID from the frame.
3. If there is no FCF-MAP the use the spec. default FCF-MAP and the
destination ID from the frame.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the case of UPIU/DME request execution failed in UFS device,
ufs_bsg_request() will complete the failed bsg job by calling
bsg_job_done(). Meanwhile, it returns this error status to blk-mq layer,
then triggers blk-mq completing this request again, this will cause the
following panic.
Call trace:
ll_sc___cmpxchg_case_acq_32+0x4/0x20
complete+0x28/0x70
blk_end_sync_rq+0x24/0x30
blk_mq_end_request+0xb8/0x118
bsg_job_put+0x4c/0x58
bsg_complete+0x20/0x30
blk_done_softirq+0xb4/0xe8
do_softirq+0x154/0x3f0
run_ksoftirqd+0x4c/0x68
smpboot_thread_fn+0x22c/0x268
kthread+0x130/0x138
ret_from_fork+0x10/0x1c
Code: f84107fe d65f03c0 d503201f f9800011 (885ffc10)
---[ end trace d92825bff6326e66 ]---
Kernel panic - not syncing: Fatal exception in interrupt
This patch is to fix this issue. The solution is to complete the ufs-bsg
job only if no error happened.
[mkp: commit description tweak]
Fixes: df032bf27a (scsi: ufs: Add a bsg endpoint that supports UPIUs)
Signed-off-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct dev_dbg to dev_err, so as to print out the error information in
case of DME command failed.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three driver fixes (and one version number update): a suspend hang in
ufs, a qla hard lock on module removal and a qedi panic during
discovery.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXQ5HJiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYoMAQDmq1hE
rnBYcnQHdLWztkg7taCqnFdvjUocQES3+tuuVQEA+OOSqD7cz6ZKX5crZdSJm0Ka
BqeTaOMoZXUFkQ4NA9c=
=Vr0g
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three driver fixes (and one version number update): a suspend hang in
ufs, a qla hard lock on module removal and a qedi panic during
discovery"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix hardlockup in abort command during driver remove
scsi: ufs: Avoid runtime suspend possibly being blocked forever
scsi: qedi: update driver version to 8.37.0.20
scsi: qedi: Check targetname while finding boot target information
To support scenarios which aren't bound to nvmetcli add port scenarios,
which is currently where the nvmet_fc transport invokes the discovery
event callbacks, a syfs attribute is added to lpfc which can be written
to cause an RSCN to be generated for the nport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch updates RSCN receive processing to check for the remote
port being an NVME port, and if so, invoke the nvme_fc callback to
rescan the remote port. The rescan will generate a discovery udev
event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for the nvmet discovery op. When the callback
routine is called, the driver will call the routine to generate an RSCN
to the port on the other end of the link.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds general RSCN support:
- The ability to transmit an RSCN to the port on the other end of
the link (regular port if pt2pt, or fabric controller if fabric).
- And general recognition of an RSCN ELS when an ELS is received.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The 'affinity_hint_set' is not used any longer since commit
0d9f0a52c8 ("virtio_scsi: use virtio IRQ affinity").
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Once we unlock adapter->hw_lock in pvscsi_queue_lck() nothing prevents just
queued scsi_cmnd from completing and freeing the request. Thus cmd->cmnd[0]
dereference can dereference already freed request leading to kernel crashes
or other issues (which one of our customers observed). Store cmd->cmnd[0]
in a local variable before unlocking adapter->hw_lock to fix the issue.
CC: <stable@vger.kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use existing macros. No functional change.
[mkp: typo]
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support is easier with all driver parameters visible in sysfs. Also I've
replaced a constant with an octal permission.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New Qualcomm AArch64 based laptops are now available which use UFS as their
primary data storage medium. These devices are supplied with ACPI support
out of the box. This patch ensures the Qualcomm UFS driver will be bound
when the "QCOM24A5" H/W device is advertised as present.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with
memory for some number of elements for that array. For example:
struct MR_PD_CFG_SEQ_NUM_SYNC {
...
struct MR_PD_CFG_SEQ seq[1];
} __packed;
Make use of the struct_size() helper instead of an open-coded version in
order to avoid any potential type mistakes.
So, replace the following form:
sizeof(struct MR_PD_CFG_SEQ_NUM_SYNC) + (sizeof(struct MR_PD_CFG_SEQ) * (MAX_PHYSICAL_DEVICES - 1))
with:
struct_size(pd_sync, seq, MAX_PHYSICAL_DEVICES - 1)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A system bus error during a PDMA send operation can result in bytes being
lost. Theoretically that could cause the target to remain in DATA OUT phase
and the initiator (expecting a phase change) would time-out waiting for the
Last Byte Sent flag. Should that happen, fail the transfer so the core
driver will stop using PDMA with this target.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for Apple's custom "SCSI DMA" chip. This patch doesn't make use
of its DMA capability. Just the PDMA capability is sufficient to improve
sequential read throughput by a factor of 5.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Joshua Thompson <funaho@jurai.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A system bus error during a PDMA transfer can mess up the calculation of
the transfer residual (the PDMA handshaking hardware lacks a byte
counter). This results in data corruption.
The algorithm in this patch anticipates a bus error by starting each
transfer with a MOVE.B instruction. If a bus error is caught the transfer
will be retried. If a bus error is caught later in the transfer (for a
MOVE.W instruction) the transfer gets failed and subsequent requests for
that target will use PIO instead of PDMA.
This avoids the "!REQ and !ACK" error so the severity level of that message
is reduced to KERN_DEBUG.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org # v4.14+
Fixes: 3a0f64bfa9 ("mac_scsi: Fix pseudo DMA implementation")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reported-by: Chris Jones <chris@martin-jones.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some targets introduce delays when handshaking the response to certain
commands. For example, a disk may send a 96-byte response to an INQUIRY
command (or a 24-byte response to a MODE SENSE command) too slowly.
Apparently the first 12 or 14 bytes are handshaked okay but then the system
bus error timeout is reached while transferring the next word.
Since the scsi bus phase hasn't changed, the driver then sets the target
borken flag to prevent further PDMA transfers. The driver also logs the
warning, "switching to slow handshake".
Raise the PDMA threshold to 512 bytes so that PIO transfers will be used
for these commands. This default is sufficiently low that PDMA will still
be used for READ and WRITE commands.
The existing threshold (16 bytes) was chosen more or less at random.
However, best performance requires the threshold to be as low as possible.
Those systems that don't need the PIO workaround at all may benefit from
mac_scsi.setup_use_pdma=1
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org # v4.14+
Fixes: 3a0f64bfa9 ("mac_scsi: Fix pseudo DMA implementation")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A PDMA error is handled in the core driver by setting the device's 'borken'
flag and aborting the command. Unfortunately, do_abort() is not
dependable. Perform a SCSI bus reset instead, to make sure that the command
fails and gets retried.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org # v4.20+
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The reselection interrupt gets disabled during selection and must be
re-enabled when hostdata->connected becomes NULL. If it isn't re-enabled a
disconnected command may time-out or the target may wedge the bus while
trying to reselect the host. This can happen after a command is aborted.
Fix this by enabling the reselection interrupt in NCR5380_main() after
calls to NCR5380_select() and NCR5380_information_transfer() return.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org # v4.9+
Fixes: 8b00c3d5d4 ("ncr5380: Implement new eh_abort_handler")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 4822827a69.
The purpose of that commit was to suppress a timeout warning message which
appeared to be caused by target latency. But suppressing the warning is
undesirable as the warning may indicate a messed up transfer count.
Another problem with that commit is that 15 ms is too long to keep
interrupts disabled as interrupt latency can cause system clock drift and
other problems.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 4822827a69 ("scsi: ncr5380: Increase register polling limit")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Host reset oopses because it calls wd719x_chip_init, which calls
request_firmware, under a spinlock. Stop the RISC first, then flush active
SCBs under a spinlock. Finally call wd719x_chip_init unlocked.
Also found and fixed more bugs during tests:
Affected active SCBs were not flushed during abort, bus and device
reset. This caused problems in a following host reset (hang or oops).
Device and bus reset failed under load because the result of the reset
command is WD719X_SUE_TERM or WD719X_SUE_RESET. Don't treat these codes as
error in wd719x_wait_done.
wd719x_direct_cmd for RESET/ABORT commands didn't work properly, causing
timeouts. Looks like it was caused by the WD719X_DISABLE_INT bit. Not
setting it for RESET/ABORT commands seems to fix the probem. Also lower
the log level of the corresponding "direct command completed" message to
debug.
Unfortunately, my documentation is missing some pages, including page
67 (SPIDER67.gif) about resets :(
Reported-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several SCSI transport and LLD drivers surround code that does not
tolerate concurrent calls of .queuecommand() with scsi_target_block() /
scsi_target_unblock(). These last two functions use
blk_mq_quiesce_queue() / blk_mq_unquiesce_queue() for scsi-mq request
queues to prevent concurrent .queuecommand() calls. However, that is
not sufficient to prevent .queuecommand() calls from scsi_send_eh_cmnd().
Hence surround the .queuecommand() call from the SCSI error handler with
code that avoids that .queuecommand() gets called in the blocked state.
Note: converting the .queuecommand() call in scsi_send_eh_cmnd() into
code that calls blk_get_request() + blk_execute_rq() is not an option
since scsi_send_eh_cmnd() must be able to make forward progress even
if all requests have been allocated.
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ability to modify the SCSI device state was introduced by commit
638127e579a4 ("[PATCH] Fix error handler offline behaviour"; v2.6.12). That
same commit introduced the following device states:
{ SDEV_CREATED, "created" },
{ SDEV_RUNNING, "running" },
{ SDEV_CANCEL, "cancel" },
{ SDEV_DEL, "deleted" },
{ SDEV_QUIESCE, "quiesce" },
{ SDEV_OFFLINE, "offline" },
The SDEV_BLOCK state was introduced later to avoid that an FC cable pull
would immediately result in an I/O error (commit 1094e682310e; "[PATCH]
suspending I/Os to a device"; v2.6.12). That same patch introduced the
ability to set the SDEV_BLOCK state from user space. I'm not sure whether
that ability was introduced on purpose or accidentally.
Since there is agreement that only writing "running" or "offline" into
the SCSI sysfs device state attribute makes sense, restrict sysfs writes
to these values.
This patch makes sure that SDEV_BLOCK is only used for its original
purpose, namely to allow transport drivers and LLDs to block further
.queuecommand() calls while transport layer or adapter recovery is in
progress.
Note: a web search for "/sys/class/scsi_device" AND "device/state"
revealed several storage configuration guides. The instructions I found
in these guides tell users to write the value "running" or "offline" in
the SCSI device state sysfs attribute and no other values.
[mkp: typo]
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: James Smart <james.smart@broadcom.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
IEEE_8021QAZ_APP_SEL_STREAM is a valid selector for iSCSI connections, so
add code to use IEEE_8021QAZ_APP_SEL_STREAM selector to get priority mask.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding functionality to allow the SCSI queue depth to be changed by
utilizing the "scsi_change_queue_depth" function.
[mkp: checkpatch]
Signed-off-by: Branden Bonaby <brandonbonaby94@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
This patch fixes the following warning:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function _base_update_ioc_page1_inlinewith_perf_mode :
drivers/scsi/mpt3sas/mpt3sas_base.c:4510:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ioc->high_iops_queues) {
^
drivers/scsi/mpt3sas/mpt3sas_base.c:4530:2: note: here
case MPT_PERF_MODE_LATENCY:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable -Wimplicit-fallthrough.
Fixes: 30cb97023f38 ("scsi: mpt3sas: Introduce perf_mode module parameter")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many times in libsas, and in LLDDs which use libsas, the check for an
expander device is re-implemented or open coded.
Use dev_is_expander() instead. We rename this from
sas_dev_type_is_expander() to not spill so many lines in referencing.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The preallocated small SGL depends on SG_CHAIN so if the ARCH doesn't
support SG_CHAIN, preallocation of small SGL can't work at all.
Fix this issue by not using small preallocation in case of NO_SG_CHAIN.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_mq_setup_tags() preallocates a big buffer for the IO SGL. The size is
based on scsi_mq_sgl_size() which is determined based on
shost->sg_tablesize and SG_CHUNK_SIZE.
Modern DMA engines are often capable of dealing with very big segments so
the resulting scsi_mq_sgl_size() is often too big. SG_CHUNK_SIZE results in
a static 4KB SGL allocation per command.
If an HBA has lots of deep queues, preallocation for the sg list can
consume substantial amounts of memory. For lpfc, nr_hw_queues can be 70
and each queue's depth 3781. This means the resulting preallocation for
the data SGL is 70*3781*2K = 517MB.
Switch to runtime allocation for SGL for lists longer than 2 entries. This
is the approach used by NVMe PCI so it should be reasonable for SCSI as
well. Runtime SGL allocation has always been the case for the legacy I/O
path so this is nothing new.
[mkp: attempted to clarify commit desc]
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_mq_setup_tags() currently preallocates a big buffer for protection
SGL entries. scsi_mq_sgl_size() is used to determine the size for both data
and protection information scatterlists but the protection buffer is
usually much smaller. For example, one 512-byte sector needs 8 bytes of
protection information. Given that the maximum number of sectors for one
request is 2560 (BLK_DEF_MAX_SECTORS) sectors, the max protection
information buffer size is just 20K.
The protection information segment count generally matches the number of
bios in the request. As a result, the typical actual number of segments
won't be very big. And should the need arise, allocating a bigger SGL from
slab is fast enough.
Pre-allocate only one SGL entry for protection information and switch to
runtime allocation in case that the protection information segment number
is bigger than 1. This reduces memory tied up by static command
allocations. For example, 500+ MB is saved on single lpfc HBA.
[mkp: attempted to clarify commit desc]
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sg_alloc_table_chained() currently allows the caller to provide one
preallocated SGL and returns if the requested number isn't bigger than
size of that SGL. This is used to inline an SGL for an IO request.
However, scattergather code only allows that size of the 1st preallocated
SGL to be SG_CHUNK_SIZE(128). This means a substantial amount of memory
(4KB) is claimed for the SGL for each IO request. If the I/O is small, it
would be prudent to allocate a smaller SGL.
Introduce an extra parameter to sg_alloc_table_chained() and
sg_free_table_chained() for specifying size of the preallocated SGL.
Both __sg_free_table() and __sg_alloc_table() assume that each SGL has the
same size except for the last one. Change the code to allow both functions
to accept a variable size for the 1st preallocated SGL.
[mkp: attempted to clarify commit desc]
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: netdev@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Guenter Roeck <linux@roeck-us.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Cc: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
Finn added the change to replace SCp.buffers_residual with
sg_is_last() for fixing updating it, and the similar change has been
applied on NCR5380.c
[mkp: clarified commit message]
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message and folded in build fix reported by zeroday]
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.195075312@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
released under the gplv2 only spdx license identifier gpl 2 0
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081203.262169268@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this file is licensed under gplv2 this file is part of the [aic94xx]
driver the [aic94xx] driver is free software you can redistribute it
and or modify it under the terms of the gnu general public license
as published by the free software foundation version 2 of the
license the [aic94xx] driver is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with [aic94xx] driver
if not write to the free software foundation inc 51 franklin st
fifth floor boston ma 02110 1301 usa
this file is licensed under gplv2 this file is part of the
[88se64xx] [88se94xx] driver the [88se64xx] [88se94xx] driver is
free software you can redistribute it and or modify it under the
terms of the gnu general public license as published by the free
software foundation version 2 of the license the [88se64xx]
[88se94xx] driver is distributed in the hope that it will be useful
but without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with [88se64xx]
[88se94xx] driver if not write to the free software foundation inc
51 franklin st fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081201.638289549@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UFS runtime suspend can be triggered after pm_runtime_enable() is invoked
in ufshcd_pltfrm_init(). However if the first runtime suspend is triggered
before binding ufs_hba structure to ufs device structure via
platform_set_drvdata(), then UFS runtime suspend will be no longer
triggered in the future because its dev->power.runtime_error was set in the
first triggering and does not have any chance to be cleared.
To be more clear, dev->power.runtime_error is set if hba is NULL in
ufshcd_runtime_suspend() which returns -EINVAL to rpm_callback() where
dev->power.runtime_error is set as -EINVAL. In this case, any future
rpm_suspend() for UFS device fails because rpm_check_suspend_allowed()
fails due to non-zero
dev->power.runtime_error.
To resolve this issue, make sure the first UFS runtime suspend get valid
"hba" in ufshcd_runtime_suspend(): Enable UFS runtime PM only after hba is
successfully bound to UFS device structure.
Fixes: 62694735ca ([SCSI] ufs: Add runtime PM support for UFS host controller driver)
Cc: stable@vger.kernel.org
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update qedi driver version to 8.37.0.20
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver version from 28.100.00.00 to 29.100.00.00
This is equivalent to Phase 10 OOB driver.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Introduce module parameter perf_mode for only Aero/Sea generation HBAs.
2. Update IOC page1 fields according to performance mode.
Below are the performance modes that can be enabled with module parameter
perf_mode:
0: Balanced - Few high iops reply queues will be enabled. Interrupt
coalescing will be enabled only for these high iops reply descriptor
queues.
1: Iops - Interrupt coalescing will be enabled on all reply queues.
Coalescing timeout is set to 0x20.This is default value for Aero.
2: Latency - Interrupt coalescing will be enabled on all reply queues.
Coalescing timeout is set to 0xA. This is a legacy behavior similar to
Ventura & Invader HBA series.
Default perf mode set by driver will be balanced mode if the following
conditions are met:
- CPU vendor = Intel;
- Aero controller working in 16GT/s pcie speed
Performance mode will be set to latency mode for all other cases.
4k Random Read IO performance numbers on 24 SAS SSD drives for above three
permormance modes. Performance data is from Intel Skylake and HGST SS300
(drive model SDLL1DLR400GCCA1).
IOPs:
-----------------------------------------------------------------------
|perf_mode | qd = 1 | qd = 64 | note |
|-------------|--------|---------|-------------------------------------
|balanced | 259K | 3061k | Provides max performance numbers |
| | | | both on lower QD workload & |
| | | | also on higher QD workload |
|-------------|--------|---------|-------------------------------------
|iops | 220K | 3100k | Provides max performance numbers |
| | | | only on higher QD workload. |
|-------------|--------|---------|-------------------------------------
|latency | 246k | 2226k | Provides good performance numbers |
| | | | only on lower QD worklaod. |
-----------------------------------------------------------------------
Avarage Latency:
-----------------------------------------------------
|perf_mode | qd = 1 | qd = 64 |
|-------------|--------------|----------------------|
|balanced | 92.05 usec | 501.12 usec |
|-------------|--------------|----------------------|
|iops | 108.40 usec | 498.10 usec |
|-------------|--------------|----------------------|
|latency | 97.10 usec | 689.26 usec |
-----------------------------------------------------
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable interrupt coalescing only on high iops queues.
In ioc config page 1, offset 0x14 (ProductSpecific field) is used to
determine interrupt coalescing enabled/disabled on per reply descriptor
post queue group(8) basis. If 31st bit is zero, then interrupt coalescing
is enabled for all reply descriptor post queues. If 31st bit is set to one,
then user can enable/disable interrupt coalescing on per reply descriptor
post queue group(8) basis. So to enable interrupt coalescing only on first
reply descriptor post queue group (i.e. on high iops queues), set bit 0 and
31.
This configuration should reset during driver unload or shutdown to the
default settings. For this, the driver takes copy of default ioc page 1 and
copies back the default or unmodified ioc page1 during unload and
shutdown. This means that on next driver load (e.g. if older version driver
is loaded by user), current modified changes on ioc page1 won't take
effect.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
High iops queues are mapped to non-managed irqs. Set affinity of
non-managed irqs to local numa node. Low latency queues are mapped to
managed irqs.
Driver reserves some reply queues for max iops (through
pci_alloc_irq_vectors_affinity and .pre_vectors interface). The rest of
queues are for low latency.
Based on io workload in io submission path, driver will decide which group
of reply queues (either high iops queues or low latency queues) to be
used. High iops queues will be mapped to local numa node of controller and
low latency queues will be mapped to cpus across numa nodes. In general,
high iops and low latency queues should fit into 128 reply queues
which is the max number of reply queues supported by Aero/Sea.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the IO submission path _base_get_msix_index is called twice. Initially
while getting the smid and subsequently while posting the request
descriptor (RD).
Refactor code to query msix index only while posting the request
descriptor. Save determined msix index in msix_io field.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver will use round-robin method for io submission in batches within
the high iops queues when the number of in-flight ios on the target device
is larger than 8. Otherwise the driver will use low latency reply queues.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code refactoring.
In function _base_get_msix_index, add scmd as second argument. This change
is made in preparation for the next patch where we introduce a new function
to get the MSI-X index for high iops queues.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Aero controllers support balanced performance mode through the ability to
configure queues with different properties.
Reply queues with interrupt coalescing enabled are called "high iops reply
queues" and reply queues with interrupt coalescing disabled are called "low
latency reply queues".
The driver configures a combination of high iops and low latency reply
queues if:
- HBA is an AERO controller;
- MSI-X vectors supported by the HBA is 128;
- Total CPU count in the system more than high iops queue count;
- Driver is loaded with default max_msix_vectors module parameter; and
- System booted in non-kdump mode.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the Aero HBA supports Atomic Request Descriptors, it sets the Atomic
Request Descriptor Capable bit in the IOCCapabilities field of the IOCFacts
Reply message. Driver uses an Atomic Request Descriptor as an alternative
method for posting an entry onto a request queue.
The posting of an Atomic Request Descriptor is an atomic operation,
providing a safe mechanism for multiple processors on the host to post
requests without synchronization. This Atomic Request Descriptor format is
identical to first 32 bits of Default Request Descriptor and uses only 32
bits.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code refactoring introduces function pointers.
Host uses Request Descriptors of different types for posting an entry onto
a request queue. Based on controller type and capabilities, host can also
use atomic descriptors other than normal descriptors. Using function
pointer will avoid if-else statements
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use existing macros. No functional change.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Checkpatch emits a warning when using symbolic permissions. Use octal
permissions instead. No functional change.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support is easier with all driver parameters visible in sysfs.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_fw_crash_buffer_show:
drivers/scsi/megaraid/megaraid_sas_base.c:3138:16: warning: variable buff_addr set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_get_pd_list:
drivers/scsi/megaraid/megaraid_sas_base.c:4426:13: warning: variable ci_h set but not used [-Wunused-but-set-variable]
'buff_addr' is never used since inroduction in commit fc62b3fc90
("megaraid_sas : Firmware crash dump feature support")
'ci_h' is not used since commit 9b3d028f34 ("scsi: megaraid_sas:
Pre-allocate frequently used DMA buffers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_create_frame_pool:
drivers/scsi/megaraid/megaraid_sas_base.c:4124:6: warning: variable sge_sz set but not used [-Wunused-but-set-variable]
It's not used any more since commit 200aed582d ("megaraid_sas: endianness
related bug fixes and code optimization")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building powerpc pseries_defconfig or powernv_defconfig:
drivers/scsi/lpfc/lpfc_nvmet.c:224:1: error: unused function
'lpfc_nvmet_get_ctx_for_xri' [-Werror,-Wunused-function]
drivers/scsi/lpfc/lpfc_nvmet.c:246:1: error: unused function
'lpfc_nvmet_get_ctx_for_oxid' [-Werror,-Wunused-function]
These functions are only compiled when CONFIG_NVME_TARGET_FC is enabled.
Use that same condition so there is no more warning. While the fixes commit
did not introduce these functions, it caused these warnings.
Fixes: 4064b27417a7 ("scsi: lpfc: Make some symbols static")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
clang warns:
drivers/scsi/ibmvscsi/ibmvscsi.c:2126:7: warning: variable 'rc' is used
uninitialized whenever switch case is taken [-Wsometimes-uninitialized]
case IBMVSCSI_HOST_ACTION_NONE:
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvscsi.c:2151:6: note: uninitialized use occurs
here
if (rc) {
^~
Initialize rc in the IBMVSCSI_HOST_ACTION_UNBLOCK case statement then
shuffle IBMVSCSI_HOST_ACTION_NONE down to the default case statement and
make it return early so that rc is never used uninitialized in this
function.
Fixes: 035a3c4046b5 ("scsi: ibmvscsi: redo driver work thread to use enum action states")
Link: https://github.com/ClangBuiltLinux/linux/issues/502
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Suggested-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/lpfc/lpfc_sli.c:115:1: warning: symbol 'lpfc_sli4_pcimem_bcopy' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_sli.c:7854:1: warning: symbol 'lpfc_sli4_process_missed_mbox_completions' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:223:27: warning: symbol 'lpfc_nvmet_get_ctx_for_xri' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:245:27: warning: symbol 'lpfc_nvmet_get_ctx_for_oxid' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_init.c:75:10: warning: symbol 'lpfc_present_cpu' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/lpfc/lpfc_init.c: In function lpfc_setup_cq_lookup:
drivers/scsi/lpfc/lpfc_init.c:9359:30: warning: variable qp set but not used [-Wunused-but-set-variable]
It's not used since commit e70596a60f88 ("scsi: lpfc: Fix poor use of
hardware queues if fewer irq vectors")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw, stash is enabled to promote performance, but it does little to
improve performance according to current tests. What's more, it causes
exceptions for some situations, so disable it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several error codes will be generated between PHY down to up.
This issue was introduced by HW design. The designers came to the
conclusion that we should ignore these errors.
Signed-off-by: Jiaxing Luo <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It reports a error as follows from some tools at two places in our code:
runtime error: left shift of 4 by 29 places cannot be represented in type
'int' So change the type of the two numbers to unsigned to avoid the error.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Macro HISI_SAS_SGE_PAGE_CNT is defined to SG_CHUNK_SIZE, which is 128.
This means that sizeof(struct hisi_sas_slot_buf_table) is 4192. This is
just over a 4K, which can mean inefficient DMA memory usage (for no PI).
Reduce the size of HISI_SAS_SGE_PAGE_CNT to 124 to fit in a 4K page. With
this change, we experience no performance hit.
Cc: dann frazier <dann.frazier@canonical.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The argument of dev_err() called by multi_bit_ecc_error_process_v3_hw() is
not right. We pass two arguments, but there is only one printk format
specifier in the string.
Also move the print format string to dev_err().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When removing the driver or when probe fails, we need to delete the PHY
timers.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_suspend:
drivers/scsi/megaraid/megaraid_sas_base.c:7269:20: warning: variable host set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_aen_polling:
drivers/scsi/megaraid/megaraid_sas_base.c:8397:15: warning: variable wait_time set but not used [-Wunused-but-set-variable]
'host' never used since introduction in commit 31ea708897 ("[SCSI]
megaraid_sas: add hibernation support")
'wait_time' never used since commit 11c71cb4ab ("megaraid_sas: Do
not allow PCI access during OCR")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_transition_to_ready:
drivers/scsi/megaraid/megaraid_sas_base.c:3900:6: warning: variable cur_state set but not used [-Wunused-but-set-variable]
Never used since commit 7218df69e3 ("[SCSI] megaraid_sas: use the
firmware boot timeout when waiting for commands")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _ctl_ioctl_main(), 'ioctl_header' is fetched the first time from
userspace. 'ioctl_header.ioc_number' is then checked. The legal result is
saved to 'ioc'. Then, in condition MPT3COMMAND, the whole struct is fetched
again from the userspace. Then _ctl_do_mpt_command() is called, 'ioc' and
'karg' as inputs.
However, a malicious user can change the 'ioc_number' between the two
fetches, which will cause a potential security issues. Moreover, a
malicious user can provide a valid 'ioc_number' to pass the check in first
fetch, and then modify it in the second fetch.
To fix this, we need to recheck the 'ioc_number' in the second fetch.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Acked-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently auto-hibernate is activated if host supports auto-hibern8
capability. However error-handling is not implemented, which makes the
feature somewhat risky.
If either "Hibernate Enter" or "Hibernate Exit" fail during auto-hibernate
flow, the corresponding interrupt "UIC_HIBERNATE_ENTER" or
"UIC_HIBERNATE_EXIT" shall be raised according to UFS specification.
This patch adds auto-hibernate error-handling:
- Monitor "Hibernate Enter" and "Hibernate Exit" interrupts after
auto-hibernate feature is activated.
- If a failure happens, trigger error-handling just like
"manual-hibernate" failure and apply the same recovery flow: schedule
UFS error handler in ufshcd_check_errors(), and then do host reset and
restore in UFS error handler.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some vendor-specific initialization flow may set its own auto-hibernate
timer. In this case, do not overwrite timer value as "default value" in
ufshcd_init().
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The checking of Auto-Hibernation support is used in many places in the
driver, thus re-factor it as ufshcd_is_auto_hibern8_supported() to make
code more clean.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since we are processing events synchronously now, the second call of
sas_ex_join_wide_port() in sas_ex_discover_dev() is not needed. There will
be no races with other works in disco workqueue. So remove the second
sas_ex_join_wide_port().
I did not change the return value of 'res' to error when discover failed
because we need to continue to discover other phys if one phy discover
failed. So let's keep that logic as before and just add a debug log to
detect the failure. And directly return if second fanout expander attatched
to the parent expander because it has nothing to do after the phy is
disabled.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the check for a lockup_detected failure exits via the label
return_reset_status that reads and dereferences an uninitialized pointer
dev. Fix this by ensuring dev is inintialized to null.
Addresses-Coverity: ("Uninitialized pointer read")
Fixes: 14991a5bade5 ("scsi: hpsa: correct device resets")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix abord to abort.
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PCMCIA card support to Future Domain SCSI driver.
Tested with IBM SCSI PCMCIA Adapter 40G1890.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add register bit definitions from documentation to header file and use them
instead of magic constants. No changes to generated binary.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a successful SRP login response we call scsi_unblock_requests() to
kick any pending IOs. The callback to process this SRP response happens in
a tasklet and therefore is in softirq context. The result of such is that
when blk-mq is enabled, it is no longer safe to call scsi_unblock_requests()
from this context. The result of duing so triggers the following WARN_ON
splat in dmesg after a host reset or CRQ reenablement.
WARNING: CPU: 0 PID: 0 at block/blk-mq.c:1375 __blk_mq_run_hw_queue+0x120/0x180
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.0.0-rc8 #4
NIP [c0000000009771e0] __blk_mq_run_hw_queue+0x120/0x180
LR [c000000000977484] __blk_mq_delay_run_hw_queue+0x244/0x250
Call Trace:
__blk_mq_delay_run_hw_queue+0x244/0x250
blk_mq_run_hw_queue+0x8c/0x1c0
blk_mq_run_hw_queues+0x60/0x90
scsi_run_queue+0x1e4/0x3b0
scsi_run_host_queues+0x48/0x80
login_rsp+0xb0/0x100
ibmvscsi_handle_crq+0x30c/0x3e0
ibmvscsi_task+0x54/0xe0
tasklet_action_common.isra.3+0xc4/0x1a0
__do_softirq+0x174/0x3f4
irq_exit+0xf0/0x120
__do_irq+0xb0/0x210
call_do_irq+0x14/0x24
do_IRQ+0x9c/0x130
hardware_interrupt_common+0x14c/0x150
This patch fixes the issue by introducing a new host action for unblocking
the scsi requests in our seperate work thread.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current implemenation relies on two flags in the driver's private host
structure to signal the need for a host reset or to reenable the CRQ after
a LPAR migration. This patch does away with those flags and introduces a
single action flag and defined enums for the supported kthread work
actions. Lastly, the if/else logic is replaced with a switch statement.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Wire up the host_reset function in our driver_template to allow a user
requested adpater reset via the host_reset sysfs attribute.
Example:
echo "adapter" > /sys/class/scsi_host/host0/host_reset
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.3
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel warnings may be seen with preempt debugging enabled.
Replace smp_processor_id calls with raw_smp_processor_id or cpu information
stored in hdwq structures.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Crashes in scsi_queue_rq or in dma_unmap_direct_sg during BFS when lpfc has
lpfc_enable_bg=1.
lpfc is setting DIX and prot sg after scsi_add_host_with_dma() has been
called. The scsi_host_set_prot() and scsi_host_set_guard() routines need to
be called before scsi_add_host_with_dma().
Revise the calling sequence to set the protection/guard data before calling
scsi_add_host_with_dma().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FDMI protocol support registration was not accurately showing nvme
support. The fcponly-path clears the parameter object.
Move the code out of the fcponly code path. Fix the FDMI registration data
to properly check for nvme support. Commonize the manner in which the fdmi
routines set protocol support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issuing a LUN reset was resulting in a command failure which then escalated
to a host reset.
The FCP-4 spec allows fcp_rsp_len field to specify the number of valid
bytes of FCP_RSP_INFO, and the value could be 4 or 8. The driver is
allowing only a value of 8, thus it failed the command.
Revise the driver to allow 4 or 8.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While fixing the resources per socket, realized the driver was not using
hardware queues (up to 1 per cpu) if there were fewer interrupt
vectors. The driver was only using the hardware queue assigned to the cpu
with the vector.
Rework the affinity map check to use the additional hardware queue elements
that had been allocated. If the cpu count exceeds the hardware queue count
- share, but choose what is shared with by: hyperthread peer, core peer,
socket peer, or finally similar cpu in a different socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver was coded expecting enough hardware queues and interrupt vectors
such that at least there was one per socket. In the case where there were
fewer than sockets, cpus were left unassigned thus null pointers.
Rework the affinity mappings. Map settings for the cpu's that are in the
irq cpu mask. For each cpu not in the mask, map to another cpu that does
have a mask. Choice of the "other" cpu will attempt to map to the same cpu
but differing hyperthread, or cpu within in same core, or cpu within same
socket, or finally cpu in the base socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalid logical speed is displayed for trunk enabled ports when all ports
are down. Also noted that link speed is incorrectly reported for the units
when links are up.
Current code is returning the logical link speed from the last event from
the adapter. In cases where the last link went down, the link speed in the
event was not valid - meaning that although the links where down the field
had a bogus value.
Rework the event handling to qualify the trunk link state before using the
event speed data.
Also correct units on other areas where the logical link speed was taken
from a link event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
eq create is leaking mailbox memory if it encounters an error.
rework error path to free the memory.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver unconditionally says fw doesn't support nvme when in
truth it was a driver parameter settings that disabled nvme support.
Rework the code validating nvme support to accurately report what
condition is disabling nvme support. Save state on whether nvme
fw supports nvme in case sysfs attributes change dynamically.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a race condition with the abort handler declaring a waitq
item on it's stack, followed by a timeout in the abort handler that
has it give up on the abort return to its caller. When the io is
finally aborted and its completion handler called, it references
the waitq element that the abort_handler set up, which is no longer
valid resulting in a deadlock.
Fix by clearing the waitq reference, under lock, when the abort
handler timeout gives up. Have the completion handler validate the
waitq before referencing it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When queued work is executed posting a new command to the transport
the driver is reporting a null buffer.
The driver had received an ABTS which matched a command that had
been scheduled for delivery to the transport. The driver proceeded
to cancel the command, but the work item was never cancelled.
Fix by cancelling the queued work item. Also turns out the ABTS
response was not properly sending a BA_ACC, so set the flag to
send the ACC.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use-after-free memory overwrite detected. Problem reported
by Ewan Milne at Red Hat after running lpfc target with additional
memory checking enabled.
Race condition when lpfc_nvmet_xmt_ls_rsp_cmp frees the ctxp
memory in interrupt context before lpfc_nvmet_xmt_ls_rsp
clears a field in the ctxp after successfully issuing the wqe.
Remove the unnecessary ctxp write after reposting the rq buffer. The
ctxp->rqb_buffer field is not checked in LS handling after the wqe
is submitted.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reported-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under heavy load the target stops responding, the drivers aborts
timeout and we start recovery by logging out of the target, but
the target is never logged into again.
In a point-to-point scenario, there were battling PLOGI's. When we
received a PLOGI request after having sent one, the driver cancels
the processing of the original plogi. However, the completion path
of the remaining plogi was coded to skip the reg_rpi that should
be happening on the 2nd plogi.
Correct by adding a simple pt2pt check such that the 2nd plogi isn't
skipped and the reg_login occurs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turns out the message change in 12.2.0.1 for unsupported topology
makes the linux driver out of sync with other products.
Revert the message back to the prior content for product consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently is relying on firmware to match ABTSs to existing
exchanges. This works fine as long as an exchange has been assigned to the
io and work posted to it. However, for unmapped frames (rxid=0xFFFF), the
driver has yet to assign an xri. The driver was blindly saying it couldn't
match the ABTS and sending the BA_xxx. However, the command frame may have
been in queues waiting on xri's before posting to the nvmet_fc layer. When
xri's became available, the command frame would still be pushed to the
transport and that io would execute, even though the io had been killed by
ABTS. The initiator, seeing the io ABTS'd, would reuse the exchange for a
different io which would be received on the target and pushed up. If the
"zombie" io then came back down and started transmitting, the initiator
would match the oxid and accept erroneous data. Bad things happened.
Add tracking of active exchanges in the target to allow matching of a
received ABTS against active or pending IO requests. If the ABTS is matched
to a pending or active IO, the drive initiates cleanup and conditionally
notifies the transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver is notified of new command frame receipt by CQEs. As
part of the CQE processing, the driver upcalls the nvmet_fc transport to
deliver the command. nvmet_fc, as part of receiving the command builds out
a context for it, where one of the first steps is to allocate memory for
the io.
When running with tests that do large ios (1MB), it was found on some
systems, the total number of outstanding I/O's, at 1MB per, completely
consumed the system's memory. Thus additional ios were getting blocked in
the memory allocator. Given that this blocked the lpfc thread processing
CQEs, there were lots of other commands that were received and which are
then held up, and given CQEs are serially processed, the aggregate delays
for an IO waiting behind the others became cummulative - enough so that the
initiator hit timeouts for the ios.
The basic fix is to avoid the direct upcall and instead schedule a work
item for each io as it is received. This allows the cq processing to
complete very quickly, and each io can then run or block on it's own.
However, this general solution hurts latency when there are few ios. As
such, implemented the fix such that the driver watches how many CQEs it has
processed sequentially in one run. As long as the count is below a
threshold, the direct nvmet_fc upcall will be made. Only when the count is
exceeded will it revert to work scheduling.
Given that debug of this showed a surprisingly long delay in cq processing,
the io timer stats were updated to better reflect the processing of the
different points.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise a stalled adapter message to also include the number of jobs that
are stalling the thread.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A race condition resulted in receive buffers being placed in the free list
twice.
Change the locking and handling to check whether the "other" path will be
freeing the entry in a later thread and skip it if it is.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After receiving an unsolicited ABTS (meaning rxid is 0xFFFF), the driver
used the oxid from the initiator to match against a local xri which may
have been allocated for the io. The xri would be the rxid - it's an invalid
check resulting in the command not being matched or erroneously matched.
Change the lookup to use the oxid and the SID to match against received
IO's original values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Softlockups are seen in low memory situations. They are due to doing
oas_lun allocation with GFP_KERNEL in atomic contexts.
Change the calls to oas_lun to indicate atomic context so that GFP_ATOMIC
is used.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a debugfs interface for megaraid_sas driver. Provide interface to
dump driver RAID map in debugfs.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print FW supported MSI-X vector count only if FW supports
MSI-X.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add debug prints related to device list being returned by firmware. The a
debug flag to activate these prints.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add prints in resume/suspend path to help in debugging hibernation
issues. The print gives an indication when the driver entry points are
called.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a print to dump the interrupt status in system log for debugging.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver detects a firmware fault during load, dump additional
information on fault code and subcode that will help in debugging.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a sysfs interface to get the raid map index that is being used by
driver.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add prints for BAR address information during driver load. This helps in
debugging issues with BAR address changing during OS boot.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When controller fails to transition to READY state during driver probe,
dump the system interface register set. This will give snapshot of the
firmware status for debugging driver load issues.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a sysfs interface to dump the controller's system interface registers.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add option to format the buffer that is being dumped. Currently, the IO
frame and chain frame dumped in the syslog is getting split across multiple
lines based on the formatting. Fix this by using KERN_CONT in printk.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add prints to identify the internal DCMD opcode that has timed out.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch enhances the existing debug prints in reset and task management
path.
These debug prints in adapter reset path helps with debugging issues
related to IO timeouts that are seen frequently in the field. Add
additional debug prints to dump the pending command frames before
initiating an adapter reset. Also, print FastPath IOs that are
outstanding.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver will use "reply descriptor post queues" in round robin fashion when
the combined MSI-X mode is not enabled. With this IO completions are
distributed and load balanced across all the available reply descriptor
post queues equally.
This is enabled only if combined MSI-X mode is not enabled in firmware.
This improves performance and also fixes soft lockups.
When load balancing is enabled, IRQ affinity from driver needs to be
disabled.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue Description:
We have seen cpu lock up issues from field if system has a large (more than
96) logical cpu count. SAS3.0 controller (Invader series) supports max 96
MSI-X vector and SAS3.5 product (Ventura) supports max 128 MSI-X vectors.
This may be a generic issue (if PCI device support completion on multiple
reply queues).
Let me explain it w.r.t megaraid_sas supported h/w just to simplify the
problem and possible changes to handle such issues. MegaRAID controller
supports multiple reply queues in completion path. Driver creates MSI-X
vectors for controller as "minimum of (FW supported Reply queues, Logical
CPUs)". If submitter is not interrupted via completion on same CPU, there
is a loop in the IO path. This behavior can cause hard/soft CPU lockups, IO
timeout, system sluggish etc.
Example - one CPU (e.g. CPU A) is busy submitting the IOs and another CPU
(e.g. CPU B) is busy with processing the corresponding IO's reply
descriptors from reply descriptor queue upon receiving the interrupts from
HBA. If CPU A is continuously pumping the IOs then always CPU B (which is
executing the ISR) will see the valid reply descriptors in the reply
descriptor queue and it will be continuously processing those reply
descriptor in a loop without quitting the ISR handler.
megaraid_sas driver will exit ISR handler if it finds unused reply
descriptor in the reply descriptor queue. Since CPU A will be continuously
sending the IOs, CPU B may always see a valid reply descriptor (posted by
HBA Firmware after processing the IO) in the reply descriptor queue. In
worst case, driver will not quit from this loop in the ISR handler.
Eventually, CPU lockup will be detected by watchdog.
Above mentioned behavior is not common if "rq_affinity" set to 2 or
affinity_hint is honored by irqbalancer as "exact". If rq_affinity is set
to 2, submitter will be always interrupted via completion on same CPU. If
irqbalancer is using "exact" policy, interrupt will be delivered to
submitter CPU.
Problem statement:
If CPU count to MSI-X vectors (reply descriptor Queues) count ratio is not
1:1, we still have exposure of issue explained above and for that we don't
have any solution.
Exposure of soft/hard lockup is seen if CPU count is more than MSI-X
supported by device.
If CPUs count to MSI-X vectors count ratio is not 1:1, (Other way, if
CPU counts to MSI-X vector count ratio is something like X:1, where X > 1)
then 'exact' irqbalance policy OR rq_affinity = 2 won't help to avoid CPU
hard/soft lockups. There won't be any one to one mapping between
CPU to MSI-X vector instead one MSI-X interrupt (or reply descriptor queue)
is shared with group/set of CPUs and there is a possibility of having a
loop in the IO path within that CPU group and may observe lockups.
For example: Consider a system having two NUMA nodes and each node having
four logical CPUs and also consider that number of MSI-X vectors enabled on
the HBA is two, then CPUs count to MSI-X vector count ratio as 4:1.
e.g.
MSI-X vector 0 is affinity to CPU 0, CPU 1, CPU 2 & CPU 3 of NUMA node 0 and
MSI-X vector 1 is affinity to CPU 4, CPU 5, CPU 6 & CPU 7 of NUMA node 1.
numactl --hardware
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 --> MSI-X 0
node 0 size: 65536 MB
node 0 free: 63176 MB
node 1 cpus: 4 5 6 7 --> MSI-X 1
node 1 size: 65536 MB
node 1 free: 63176 MB
Assume that user started an application which uses all the CPUs of NUMA
node 0 for issuing the IOs. Only one CPU from affinity list (it can be any
cpu since this behavior depends upon irqbalance) CPU0 will receive the
interrupts from MSI-X 0 for all the IOs. Eventually, CPU 0 IO submission
percentage will be decreasing and ISR processing percentage will be
increasing as it is more busy with processing the interrupts. Gradually IO
submission percentage on CPU 0 will be zero and it's ISR processing
percentage will be 100% as IO loop has already formed within the
NUMA node 0, i.e. CPU 1, CPU 2 & CPU 3 will be continuously busy with
submitting the heavy IOs and only CPU 0 is busy in the ISR path as it
always find the valid reply descriptor in the reply descriptor queue.
Eventually, we will observe the hard lockup here.
Chances of occurring of hard/soft lockups are directly proportional to
value of X. If value of X is high, then chances of observing CPU lockups is
high.
Solution:
Use IRQ poll interface defined in "irq_poll.c".
megaraid_sas driver will execute ISR routine in softirq context and it will
always quit the loop based on budget provided in IRQ poll interface.
Driver will switch to IRQ poll only when more than a threshold number of
reply descriptors are handled in one ISR. Currently threshold is set as
1/4th of HBA queue depth.
In these scenarios (i.e. where CPUs count to MSI-X vectors count ratio is
X:1 (where X > 1)), IRQ poll interface will avoid CPU hard lockups due to
voluntary exit from the reply queue processing based on budget.
Note - Only one MSI-X vector is busy doing processing.
Select CONFIG_IRQ_POLL from driver Kconfig for driver compilation.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While an online controller reset(OCR) is in progress, there is short
duration where all access to controller's PCI config space from the host
needs to be blocked. This is due to a hardware limitation of MegaRAID
controllers.
With this patch, driver will block all access to controller's config space
from userland applications by calling pci_cfg_access_lock() while OCR is in
progress and unlocking after controller comes back to ready state.
Added helper function which locks the config space before initiating OCR
and wait for controller to become READY.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. This patch reworks code around controller reset path
which gets rid of a couple of goto labels. This is in preparation for the
next patch which adds PCI config space access locking while controller
reset is in progress.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fw_reset_no_pci_access is only applicable for MFI controllers and is not
used for Fusion controllers.
For all Fusion controllers, driver can check reset adapter bit in
status register before performing a chip reset without
setting "fw_reset_no_pci_access".
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Remove set but unused variable in
megasas_set_static_target_properties.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Future Domain 16xx ISA SCSI support card support.
Tested on IBM 92F0330 card (18C50 chip) with v1.00 BIOS.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Future Domain TMC-3260/AHA-2920A PCI card support.
Tested on Adaptec AHA-2920A PCI card.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Future Domain TMC-16xx/TMC-3260 SCSI driver.
This is the core driver, common for PCI, ISA and PCMCIA cards.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[mkp: wrong baseline, applied by hand]
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a race condition that occurs between the reset handler and the
completion handler. There are times when the wait_event condition is
never met due to this race condition and the reset never completes.
The reset_pending field is NULL initially.
t Reset Handler Thread Completion Thread
-- -------------------- -----------------
t1 if (c->reset_pending)
t2 c->reset_pending = dev; if (atomic_dev_and_test(counter))
t3 atomic_inc(counter) wait_up_all(event_sync_wait_queue)
t4
t5 wait_event(...counter == 0)
Kernel.org Bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=1994350
Bug 199435 - HPSA + P420i resetting logical Direct-Access
never complete
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Close up a rare multipath issue.
Close up small hole where a command completes after a device has been
removed from SML and before the device is re-added.
- Mark device as removed in slave_destroy
- Do not complete commands for deleted devices
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Wait longer for outstanding commands before removing a multipath
device. Increase the timeout value for ptraid commands.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct rare multipath issue where a device is deleted with an
outstanding cmd which results in a tag collision.
The cmd eventually completes. If a collision is detected wait until
the command slot is cleared.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid system stalls by switching to local workqueue.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct issue with hpsa_simple_mode module parameter. Driver was
hanging due to incorrect interrupt setup.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The osst driver is becoming obsolete, as the manufacturer went out of
business ages ago, and the maintainer has no means of testing any
improvements anymore. Plus these days flash drives are cheaper and offer a
higher capacity. So drop it completely.
Cc: Willem Riede <osst@riede.org>
Signed-off-by: Hannes Reinece <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sd_probe() easier to read by inlining sd_probe_part2(). This patch
does not change any functionality.
[mkp: applied by hand]
Cc: Lee Duncan <lduncan@suse.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As explained during the 2018 LSF/MM session about increasing SCSI disk
probing concurrency, the problems with the current probing approach are as
follows:
- The driver core is unaware of asynchronous SCSI LUN probing.
wait_for_device_probe() waits for all asynchronous probes except
asynchronous SCSI disk probes.
- There is unnecessary serialization between sd_probe() and sd_remove().
This can lead to a deadlock.
Hence this patch that modifies the sd driver such that it uses the driver
core framework for asynchronous probing. The async domain and
get_device()/put_device() pairs that became superfluous due to this change
are removed.
This patch does not affect the time needed for loading the scsi_debug
kernel module with parameters delay=0 and max_luns=256.
This patch depends on commit ef0ff68351 ("driver core: Probe devices
asynchronously instead of the driver") that went upstream in kernel version
v5.1-rc1.
Cc: Lee Duncan <lduncan@suse.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A single bug fix for hpsa. The user visible consequences aren't
clear, but the ioaccel2 raid acceleration may misfire on the malformed
request assuming the payload is big enough to require chaining (more
than 31 sg entries).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXQQdoCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfXkAP0aPFp3
fktJnJ/33j7uk4GwOGKB3cOzTnRG+gQ99SNp4AD+NPxXD1AXhdVqtEnxOAt2cm3B
wX3ImBnV+4zIDQEEg60=
=w5Is
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"A single bug fix for hpsa.
The user visible consequences aren't clear, but the ioaccel2 raid
acceleration may misfire on the malformed request assuming the payload
is big enough to require chaining (more than 31 sg entries)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: hpsa: correct ioaccel2 chaining
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
XCMhQ9s=
=cb80
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc4' into mauro
We need to pick up post-rc1 changes to various document files so they don't
get lost in Mauro's massive RST conversion push.
Page pods are used for direct data placement, this patch
enables eDRAM page pods if firmware supports this feature.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPuGTg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykBvQCg2SG+HmDH+tlwKLT/q7jZcLMPQigAoMpt9Uuy
sxVEiFZo8ZU9v1IoRb1I
=qU++
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
Some documentation files were still pointing to the old place.
Fixes: 229b4e0728 ("Documentation: PCI: convert pci.txt to reST")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Two bug fixes, both for fairly serious problems; the UFS one looks
like it could be used to exfiltrate data from the kernel, although
probably only a privileged user has access to the command management
interface and the missing unlock in smartpqi is long standing and
probably a little used error path.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXPtPfyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishV8bAP9ZWyAE
2S5emgr42Q9IunXQ305k1i/ek4y5iq3VVLmJqAD/cJgZiCcNenry8jf9McRGFBKO
HOLewQ+ErQvjf6DuxMM=
=7+Oe
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two bug fixes, both for fairly serious problems; the UFS one looks
like it could be used to exfiltrate data from the kernel, although
probably only a privileged user has access to the command management
interface and the missing unlock in smartpqi is long standing and
probably a little used error path"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: smartpqi: unlock on error in pqi_submit_raid_request_synchronous()
scsi: ufs: Check that space was properly alloced in copy_query_response
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
- set ioaccel2_sg_element member 'chain_indicator' to IOACCEL2_LAST_SG for
the last s/g element.
- set ioaccel2_sg_element member 'chain_indicator' to IOACCEL2_CHAIN when
chaining.
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Matt Perricone <matt.perricone@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 1 normalized pattern(s):
this software is available under the terms of the gnu general public
license gpl version 2 available from the file copying in the main
directory of this source tree
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 35 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.411886531@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is licensed under gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 22 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.129548190@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is released under the gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 68 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.292346262@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is licensed under gplv2 this file is part of the [aic94xx]
driver the [aic94xx] driver is free software you can redistribute it
and or modify it under the terms of the gnu general public license
as published by the free software foundation version 2 of the
license the [aic94xx] driver is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with the [aic94xx]
driver if not write to the free software foundation inc 51 franklin
st fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 19 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190112.766909183@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program see the file copying if not
write to the free software foundation 675 mass ave cambridge ma
02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190112.675111872@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you may redistribute and or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for complete details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081037.747331493@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.435762997@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation the full gnu general
public license is included in this distribution in the file called
copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 14 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.856338015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 246 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 111 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.567572064@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 33 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000435.254582722@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license gpl version 2
as published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 66 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.606369721@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license v2 0 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 23 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.115786599@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to drop the "ctrl_info->sync_request_sem" lock before returning.
Fixes: 6c223761eb ("smartpqi: initial commit of Microsemi smartpqi driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct ufs_dev_cmd is the main container that supports device management
commands. In the case of a read descriptor request, we assume that the
proper space was allocated in dev_cmd to hold the returning descriptor.
This is no longer true, as there are flows that doesn't use dev_cmd for
device management requests, and was wrong in the first place.
Fixes: d44a5f98bb (ufs: query descriptor API)
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Six minor fixes to device drivers and one to the multipath alua
handler. The most extensive fix is the zfcp port remove prevention
one, but it's impact is only s390.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXPJlASYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSElAP9A/qo+
mLomrWOPMGqkQKOX7Mp3sP5lMllbvPndrR+9KQD/eDzFp3HCyUO2OFd6aR7/X90H
IZ+cd/wJCSHenKMJOX8=
=NFnR
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six minor fixes to device drivers and one to the multipath alua
handler.
The most extensive fix is the zfcp port remove prevention one, but
it's impact is only s390"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libsas: delete sas port if expander discover failed
scsi: libsas: only clear phy->in_shutdown after shutdown event done
scsi: scsi_dh_alua: Fix possible null-ptr-deref
scsi: smartpqi: properly set both the DMA mask and the coherent DMA mask
scsi: zfcp: fix to prevent port_remove with pure auto scan LUNs (only sdevs)
scsi: zfcp: fix missing zfcp_port reference put on -EBUSY from port_remove
scsi: libcxgbi: add a check for NULL pointer in cxgbi_check_route()
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
released under gpl v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 15 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.895196075@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 107 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.615055994@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 44 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170025.980374610@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 83 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.021731668@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 12 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.745497013@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this kernel if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.038326898@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the event queue is full of phy up and down events and reached the
threshold, we will queue a shutdown-event, and set phy->in_shutdown so that
we will not queue a shutdown-event again. But before the shutdown-event can
be executed, every phy-down event will clear
phy->in_shutdown and a new shutdown-event will be queued. The queue will
be full of these shutdown-events.
Fix this by only clear phy->in_shutdown in sas_phye_shutdown(), that is
after the first shutdown-event has been executed.
Fixes: f12486e06a ("scsi: libsas: shut down the PHY if events reached the threshold")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If alloc_workqueue fails in alua_init, it should return -ENOMEM, otherwise
it will trigger null-ptr-deref while unloading module which calls
destroy_workqueue dereference
wq->lock like this:
BUG: KASAN: null-ptr-deref in __lock_acquire+0x6b4/0x1ee0
Read of size 8 at addr 0000000000000080 by task syz-executor.0/7045
CPU: 0 PID: 7045 Comm: syz-executor.0 Tainted: G C 5.1.0+ #28
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1
Call Trace:
dump_stack+0xa9/0x10e
__kasan_report+0x171/0x18d
? __lock_acquire+0x6b4/0x1ee0
kasan_report+0xe/0x20
__lock_acquire+0x6b4/0x1ee0
lock_acquire+0xb4/0x1b0
__mutex_lock+0xd8/0xb90
drain_workqueue+0x25/0x290
destroy_workqueue+0x1f/0x3f0
__x64_sys_delete_module+0x244/0x330
do_syscall_64+0x72/0x2a0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 03197b61c5 ("scsi_dh_alua: Use workqueue for RTPG")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SME is enabled, the smartpqi driver won't work on the HP DL385 G10
machine, which causes the failure of kernel boot because it fails to
allocate pqi error buffer. Please refer to the kernel log:
....
[ 9.431749] usbcore: registered new interface driver uas
[ 9.441524] Microsemi PQI Driver (v1.1.4-130)
[ 9.442956] i40e 0000:04:00.0: fw 6.70.48768 api 1.7 nvm 10.2.5
[ 9.447237] smartpqi 0000:23:00.0: Microsemi Smart Family Controller found
Starting dracut initqueue hook...
[ OK ] Started Show Plymouth Boot Scre[ 9.471654] Broadcom NetXtreme-C/E driver bnxt_en v1.9.1
en.
[ OK ] Started Forward Password Requests to Plymouth Directory Watch.
[[0;[ 9.487108] smartpqi 0000:23:00.0: failed to allocate PQI error buffer
....
[ 139.050544] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 139.589779] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts
Basically, the fact that the coherent DMA mask value wasn't set caused the
driver to fall back to SWIOTLB when SME is active.
For correct operation, lets call the dma_set_mask_and_coherent() to
properly set the mask for both streaming and coherent, in order to inform
the kernel about the devices DMA addressing capabilities.
Signed-off-by: Lianbo Jiang <lijiang@redhat.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ip_dev_find() can return NULL so add a check for NULL pointer.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MSI-X vector index is determined using qed device information and
affinity to use.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI-X vector index is determined using qed device information and
affinity to use.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always request for number of irqs equals to number of queues.
This reverts commit 1a291bce5e.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the ocxlflash filesystem to the new internal mount API as the old
one will be obsoleted and removed. This allows greater flexibility in
communication of mount parameters between userspace, the VFS and the
filesystem.
See Documentation/filesystems/mount_api.txt for more information.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
cc: "Manoj N. Kumar" <manoj@linux.ibm.com>
cc: Uma Krishnan <ukrishn@linux.ibm.com>
cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
cc: "Martin K. Petersen" <martin.petersen@oracle.com>
cc: linux-scsi@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Once upon a time we used to set ->d_name of e.g. pipefs root
so that d_path() on pipes would work. These days it's
completely pointless - dentries of pipes are not even connected
to pipefs root. However, mount_pseudo() had set the root
dentry name (passed as the second argument) and callers
kept inventing names to pass to it. Including those that
didn't *have* any non-root dentries to start with...
All of that had been pointless for about 8 years now; it's
time to get rid of that cargo-culting...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This is the same set of patches sent in the merge window as the final
pull except that Martin's read only rework is replaced with a simple
revert of the original change that caused the regression. Everything
else is an obvious fix or small cleanup.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXOh2RyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishe+mAP9PtAon
IUlSEcJaMhej3VSyjxWYxble0pbCkBYnuH220gEAk7eCISK3xwAdkWYD0wVLLqxo
9t8qgzKbZSPZVRRD8Tk=
=9p0X
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the same set of patches sent in the merge window as the final
pull except that Martin's read only rework is replaced with a simple
revert of the original change that caused the regression.
Everything else is an obvious fix or small cleanup"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
Revert "scsi: sd: Keep disk read-only when re-reading partition"
scsi: bnx2fc: fix incorrect cast to u64 on shift operation
scsi: smartpqi: Reporting unhandled SCSI errors
scsi: myrs: Fix uninitialized variable
scsi: lpfc: Update lpfc version to 12.2.0.2
scsi: lpfc: add check for loss of ndlp when sending RRQ
scsi: lpfc: correct rcu unlock issue in lpfc_nvme_info_show
scsi: lpfc: resolve lockdep warnings
scsi: qedi: remove set but not used variables 'cdev' and 'udev'
scsi: qedi: remove memset/memcpy to nfunc and use func instead
scsi: qla2xxx: Add cleanup for PCI EEH recovery
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 44 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091651.032047323@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this work is licensed under the terms of the gnu gpl version 2 or
later see the copying file in the top level directory
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 6 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520075210.858783702@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is licensed under gplv2 this program is free software you
can redistribute it and or modify it under the terms of the gnu
general public license as published by the free software foundation
either version 2 of the license or at your option any later version
this program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not write to the free software foundation inc 59 temple place suite
330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.561902672@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 11 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.370933192@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
st.c is the only st file missing licensing information. Add a
GPLv2 tag for the default kernel license.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sr.c is the only sr file missing licensing information. Add a
GPLv2 tag for the default kernel license.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sd.c is the only sd file missing licensing information. Add a
GPLv2 tag for the default kernel license.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_task.c is the only libsas file missing licensing information. Add a
GPLv2 tag for the default kernel license.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
[mkp: fixed comment syntax on *.c]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of a free form blurb.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the default kernel GPLv2 annotation to SCSI midlayer files missing any
licensing information.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program see
the file copying if not write to the free software foundation 675
mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 52 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.342335923@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 20bd1d026a.
This patch introduced regressions for devices that come online in
read-only state and subsequently switch to read-write.
Given how the partition code is currently implemented it is not
possible to persist the read-only flag across a device revalidate
call. This may need to get addressed in the future since it is common
for user applications to proactively call BLKRRPART.
Reverting this commit will re-introduce a regression where a
device-initiated revalidate event will cause the admin state to be
forgotten. A separate patch will address this issue.
Fixes: 20bd1d026a ("scsi: sd: Keep disk read-only when re-reading partition")
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently an int is being shifted and the result is being cast to a u64
which leads to undefined behaviour if the shift is more than 31 bits. Fix
this by casting the integer value 1 to u64 before the shift operation.
Addresses-Coverity: ("Bad shift operation")
Fixes: 7b59476912 ("[SCSI] bnx2fc: Handle REC_TOV error code from firmware")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a HARDWARE_ERROR is triggered for ASC=0x3e, the existing code is only
considering the case where ASCQ=0x1.
According to the http://www.t10.org/lists/asc-num.htm#ASC_3E specification,
other values may occur like a timeout (ASCQ=0x2).
This patch prints an error message when a non-handled message is received.
This can help diagnose a possible misbehavior of the controller or a
missing implementation in the Linux kernel.
This patch keeps the exact same error handling but prints a message if an
ASCQ != 1 is reported.
[mkp: clarified commit message]
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drivers/scsi/myrs.c: In function 'myrs_log_event':
drivers/scsi/myrs.c:821:24: warning: 'sshdr.sense_key' may be used uninitialized in this function [-Wmaybe-uninitialized]
struct scsi_sense_hdr sshdr;
If ev->ev_code is not 0x1C, sshdr.sense_key may be used uninitialized. Fix
this by initializing variable 'sshdr' to 0.
Fixes: 7726618639 ("scsi: myrs: Add Mylex RAID controller (SCSI interface)")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To facilitate additional options to get_user_pages_fast() change the
singular write parameter to be gup_flags.
This patch does not change any functionality. New functionality will
follow in subsequent patches.
Some of the get_user_pages_fast() call sites were unchanged because they
already passed FOLL_WRITE or 0 for the write parameter.
NOTE: It was suggested to change the ordering of the get_user_pages_fast()
arguments to ensure that callers were converted. This breaks the current
GUP call site convention of having the returned pages be the final
parameter. So the suggestion was rejected.
Link: http://lkml.kernel.org/r/20190328084422.29911-4-ira.weiny@intel.com
Link: http://lkml.kernel.org/r/20190317183438.2057-4-ira.weiny@intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mike Marshall <hubcap@omnibond.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to the couple of bug fixes, update lpfc version to 12.2.0.2
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was a missing qualification of a valid ndlp structure when calling to
send an RRQ for an abort. Add the check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many of the exit cases were not releasing the rcu read lock. Corrected the
exit paths.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There were a number of erroneous comments and incorrect older lockdep
checks that were causing a number of warnings.
Resolve the following:
- Inconsistent lock state warnings in lpfc_nvme_info_show().
- Fixed comments and code on sequences where ring lock is now held instead
of hbalock.
- Reworked calling sequences around lpfc_sli_iocbq_lookup(). Rather than
locking prior to the routine and have routine guess on what lock, take
the lock within the routine. The lockdep check becomes unnecessary.
- Fixed comments and removed erroneous hbalock checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/qedi/qedi_iscsi.c: In function 'qedi_ep_connect':
drivers/scsi/qedi/qedi_iscsi.c:813:23: warning: variable 'udev' set but not used [-Wunused-but-set-variable]
drivers/scsi/qedi/qedi_iscsi.c:812:18: warning: variable 'cdev' set but not used [-Wunused-but-set-variable]
These have never been used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
KASAN reports this:
BUG: KASAN: global-out-of-bounds in qedi_dbg_err+0xda/0x330 [qedi]
Read of size 31 at addr ffffffffc12b0ae0 by task syz-executor.0/2429
CPU: 0 PID: 2429 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
print_address_description+0x1c4/0x270 mm/kasan/report.c:187
kasan_report+0x149/0x18d mm/kasan/report.c:317
memcpy+0x1f/0x50 mm/kasan/common.c:130
qedi_dbg_err+0xda/0x330 [qedi]
? 0xffffffffc12d0000
qedi_init+0x118/0x1000 [qedi]
? 0xffffffffc12d0000
? 0xffffffffc12d0000
? 0xffffffffc12d0000
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f2d57e55c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bfa0 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 00000000200003c0 RDI: 0000000000000003
RBP: 00007f2d57e55c70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f2d57e566bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004
The buggy address belongs to the variable:
__func__.67584+0x0/0xffffffffffffd520 [qedi]
Memory state around the buggy address:
ffffffffc12b0980: fa fa fa fa 00 04 fa fa fa fa fa fa 00 00 05 fa
ffffffffc12b0a00: fa fa fa fa 00 00 04 fa fa fa fa fa 00 05 fa fa
> ffffffffc12b0a80: fa fa fa fa 00 06 fa fa fa fa fa fa 00 02 fa fa
^
ffffffffc12b0b00: fa fa fa fa 00 00 04 fa fa fa fa fa 00 00 03 fa
ffffffffc12b0b80: fa fa fa fa 00 00 02 fa fa fa fa fa 00 00 04 fa
Currently the qedi_dbg_* family of functions can overrun the end of the
source string if it is less than the destination buffer length because of
the use of a fixed sized memcpy. Remove the memset/memcpy calls to nfunc
and just use func instead as it is always a null terminated string.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During EEH error recovery testing it was discovered that driver's reset()
callback partially frees resources used by driver, leaving some stale
memory. After reset() is done and when resume() callback in driver uses
old data which results into error leaving adapter disabled due to PCIe
error.
This patch does cleanup for EEH recovery code path and prevents adapter
from getting disabled.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, qedf, smartpqi,
hpsa, lpfc, ufs, mpt3sas, ibmvfc and hisi_sas. Plus number of minor
changes, spelling fixes and other trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXNIK0yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbeFAP4wsOm6
BNqDvLbF7gHAH+oSVAeENd9tepXG2xKbUHmLRgEA1wPaUxon8L8v/SSsqwewqMXP
y6CnU6aO2iaViTNBsPs=
=RX74
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, qedf, smartpqi,
hpsa, lpfc, ufs, mpt3sas, ibmvfc and hisi_sas. Plus number of minor
changes, spelling fixes and other trivia"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (298 commits)
scsi: qla2xxx: Avoid that lockdep complains about unsafe locking in tcm_qla2xxx_close_session()
scsi: qla2xxx: Avoid that qlt_send_resp_ctio() corrupts memory
scsi: qla2xxx: Fix hardirq-unsafe locking
scsi: qla2xxx: Complain loudly about reference count underflow
scsi: qla2xxx: Use __le64 instead of uint32_t[2] for sending DMA addresses to firmware
scsi: qla2xxx: Introduce the dsd32 and dsd64 data structures
scsi: qla2xxx: Check the size of firmware data structures at compile time
scsi: qla2xxx: Pass little-endian values to the firmware
scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands
scsi: qla2xxx: Use an on-stack completion in qla24xx_control_vp()
scsi: qla2xxx: Make qla24xx_async_abort_cmd() static
scsi: qla2xxx: Remove unnecessary locking from the target code
scsi: qla2xxx: Remove qla_tgt_cmd.released
scsi: qla2xxx: Complain if a command is released that is owned by the firmware
scsi: qla2xxx: target: Fix offline port handling and host reset handling
scsi: qla2xxx: Fix abort handling in tcm_qla2xxx_write_pending()
scsi: qla2xxx: Fix error handling in qlt_alloc_qfull_cmd()
scsi: qla2xxx: Simplify qlt_send_term_imm_notif()
scsi: qla2xxx: Fix use-after-free issues in qla2xxx_qpair_sp_free_dma()
scsi: qla2xxx: Fix a qla24xx_enable_msix() error path
...
Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here last
Friday.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKuwg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymRUgCfa8Ri7KrCaBR5NHQcLhbdrX90ToQAmgNw7vpo
fqt0XpNM0CSa9O/gOr79
=8HFh
-----END PGP SIGNATURE-----
Merge tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here
last Friday"
* tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits)
USB: serial: f81232: implement break control
USB: serial: f81232: add high baud rate support
USB: serial: f81232: clear overrun flag
USB: serial: f81232: fix interrupt worker not stop
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
...
-----BEGIN PGP SIGNATURE-----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=Ot0g
-----END PGP SIGNATURE-----
Merge tag 'for-5.2/block-20190507' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"Nothing major in this series, just fixes and improvements all over the
map. This contains:
- Series of fixes for sed-opal (David, Jonas)
- Fixes and performance tweaks for BFQ (via Paolo)
- Set of fixes for bcache (via Coly)
- Set of fixes for md (via Song)
- Enabling multi-page for passthrough requests (Ming)
- Queue release fix series (Ming)
- Device notification improvements (Martin)
- Propagate underlying device rotational status in loop (Holger)
- Removal of mtip32xx trim support, which has been disabled for years
(Christoph)
- Improvement and cleanup of nvme command handling (Christoph)
- Add block SPDX tags (Christoph)
- Cleanup/hardening of bio/bvec iteration (Christoph)
- A few NVMe pull requests (Christoph)
- Removal of CONFIG_LBDAF (Christoph)
- Various little fixes here and there"
* tag 'for-5.2/block-20190507' of git://git.kernel.dk/linux-block: (164 commits)
block: fix mismerge in bvec_advance
block: don't drain in-progress dispatch in blk_cleanup_queue()
blk-mq: move cancel of hctx->run_work into blk_mq_hw_sysfs_release
blk-mq: always free hctx after request queue is freed
blk-mq: split blk_mq_alloc_and_init_hctx into two parts
blk-mq: free hw queue's resource in hctx's release handler
blk-mq: move cancel of requeue_work into blk_mq_release
blk-mq: grab .q_usage_counter when queuing request from plug code path
block: fix function name in comment
nvmet: protect discovery change log event list iteration
nvme: mark nvme_core_init and nvme_core_exit static
nvme: move command size checks to the core
nvme-fabrics: check more command sizes
nvme-pci: check more command sizes
nvme-pci: remove an unneeded variable initialization
nvme-pci: unquiesce admin queue on shutdown
nvme-pci: shutdown on timeout during deletion
nvme-pci: fix psdt field for single segment sgls
nvme-multipath: don't print ANA group state by default
nvme-multipath: split bios with the ns_head bio_set before submitting
...
Hi Linus,
This is my very first pull-request. I've been working full-time as
a kernel developer for more than two years now. During this time I've
been fixing bugs reported by Coverity all over the tree and, as part
of my work, I'm also contributing to the KSPP. My work in the kernel
community has been supervised by Greg KH and Kees Cook.
OK. So, after the quick introduction above, please, pull the following
patches that mark switch cases where we are expecting to fall through.
These patches are part of the ongoing efforts to enable -Wimplicit-fallthrough.
They have been ignored for a long time (most of them more than 3 months,
even after pinging multiple times), which is the reason why I've created
this tree. Most of them have been baking in linux-next for a whole development
cycle. And with Stephen Rothwell's help, we've had linux-next nag-emails
going out for newly introduced code that triggers -Wimplicit-fallthrough
to avoid gaining more of these cases while we work to remove the ones
that are already present.
I'm happy to let you know that we are getting close to completing this
work. Currently, there are only 32 of 2311 of these cases left to be
addressed in linux-next. I'm auditing every case; I take a look into
the code and analyze it in order to determine if I'm dealing with an
actual bug or a false positive, as explained here:
https://lore.kernel.org/lkml/c2fad584-1705-a5f2-d63c-824e9b96cf50@embeddedor.com/
While working on this, I've found and fixed the following missing
break/return bugs, some of them introduced more than 5 years ago:
84242b82d87850b51b6c5e420fe63509186e5034b5be8531817264235ee7cc5034a5d2479826cc865340f23df8df997abeeb2f10d82373307b00c5e65d25ff7a54a7ed5b3e7dc24bfa8f21ad0eaee6199ba8376ce1dc586a60a1a8e9b186f14e57562b4860747828eac5b974bee9cc44ba91162c930e3d0a
Once this work is finish, we'll be able to universally enable
"-Wimplicit-fallthrough" to avoid any of these kinds of bugs from
entering the kernel again.
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----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=k30z
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull Wimplicit-fallthrough updates from Gustavo A. R. Silva:
"Mark switch cases where we are expecting to fall through.
This is part of the ongoing efforts to enable -Wimplicit-fallthrough.
Most of them have been baking in linux-next for a whole development
cycle. And with Stephen Rothwell's help, we've had linux-next
nag-emails going out for newly introduced code that triggers
-Wimplicit-fallthrough to avoid gaining more of these cases while we
work to remove the ones that are already present.
We are getting close to completing this work. Currently, there are
only 32 of 2311 of these cases left to be addressed in linux-next. I'm
auditing every case; I take a look into the code and analyze it in
order to determine if I'm dealing with an actual bug or a false
positive, as explained here:
https://lore.kernel.org/lkml/c2fad584-1705-a5f2-d63c-824e9b96cf50@embeddedor.com/
While working on this, I've found and fixed the several missing
break/return bugs, some of them introduced more than 5 years ago.
Once this work is finished, we'll be able to universally enable
"-Wimplicit-fallthrough" to avoid any of these kinds of bugs from
entering the kernel again"
* tag 'Wimplicit-fallthrough-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (27 commits)
memstick: mark expected switch fall-throughs
drm/nouveau/nvkm: mark expected switch fall-throughs
NFC: st21nfca: Fix fall-through warnings
NFC: pn533: mark expected switch fall-throughs
block: Mark expected switch fall-throughs
ASN.1: mark expected switch fall-through
lib/cmdline.c: mark expected switch fall-throughs
lib: zstd: Mark expected switch fall-throughs
scsi: sym53c8xx_2: sym_nvram: Mark expected switch fall-through
scsi: sym53c8xx_2: sym_hipd: mark expected switch fall-throughs
scsi: ppa: mark expected switch fall-through
scsi: osst: mark expected switch fall-throughs
scsi: lpfc: lpfc_scsi: Mark expected switch fall-throughs
scsi: lpfc: lpfc_nvme: Mark expected switch fall-through
scsi: lpfc: lpfc_nportdisc: Mark expected switch fall-through
scsi: lpfc: lpfc_hbadisc: Mark expected switch fall-throughs
scsi: lpfc: lpfc_els: Mark expected switch fall-throughs
scsi: lpfc: lpfc_ct: Mark expected switch fall-throughs
scsi: imm: mark expected switch fall-throughs
scsi: csiostor: csio_wr: mark expected switch fall-through
...
-----BEGIN PGP SIGNATURE-----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=WZfC
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow state reset of printk_once() calls.
- Prevent crashes when dereferencing invalid pointers in vsprintf().
Only the first byte is checked for simplicity.
- Make vsprintf warnings consistent and inlined.
- Treewide conversion of obsolete %pf, %pF to %ps, %pF printf
modifiers.
- Some clean up of vsprintf and test_printf code.
* tag 'printk-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
lib/vsprintf: Make function pointer_string static
vsprintf: Limit the length of inlined error messages
vsprintf: Avoid confusion between invalid address and value
vsprintf: Prevent crash when dereferencing invalid pointers
vsprintf: Consolidate handling of unknown pointer specifiers
vsprintf: Factor out %pO handler as kobject_string()
vsprintf: Factor out %pV handler as va_format()
vsprintf: Factor out %p[iI] handler as ip_addr_string()
vsprintf: Do not check address of well-known strings
vsprintf: Consistent %pK handling for kptr_restrict == 0
vsprintf: Shuffle restricted_pointer()
printk: Tie printk_once / printk_deferred_once into .data.once for reset
treewide: Switch printk users from %pf and %pF to %ps and %pS, respectively
lib/test_printf: Switch to bitmap_zalloc()
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
We need this to make the usb-gadget branch merge cleaner. And for
testing to keep from hitting the same issues already fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "(&ctio->u.status1.sense_data)[i]" where i >= 0 expressions in
qlt_send_resp_ctio() are probably typos and should have been
"(&ctio->u.status1.sense_data[4 * i])" instead. Instead of only fixing
these typos, modify the code for storing sense data such that it becomes
easy to read. This patch fixes a Coverity complaint about accessing an
array outside its bounds.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: be25152c0d ("qla2xxx: Improve T10-DIF/PI handling in driver.") # v4.11.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A reference count underflow is a severe bug. Hence complain loudly if a
reference count underflow happens.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes the code easier to read and more compact.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce two structures for the (DMA address, length) combination instead
of using separate structure members for the DMA address and length. This
patch fixes several Coverity complaints about 'cur_dsd' being used to write
outside the bounds of structure members.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the next patch will modify several firmware data structures, add
compile time checks that verify that these structures have the correct
size.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pass dsd_list_len in little endian format to the firmware instead of in CPU
endian format.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the *_done() functions, instead of returning early if sp->ref_count >=
2, only decrement sp->ref_count. In qla2xxx_eh_abort(), instead of deciding
what to do based on the value of sp->ref_count, decide which action to take
depending on the completion status of the firmware abort. Remove srb.cwaitq
and use srb.comp instead. In qla2x00_abort_srb(), call
isp_ops->abort_command() directly instead of calling qla2xxx_eh_abort().
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch reduces the size of struct srb.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qla24xx_async_abort_cmd() is only called from inside qla_init.c,
declare that function static. Reorder a few functions to avoid that any
forward declarations are needed.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All callbacks from the target core into the qla2xxx driver and also all I/O
completion functions are serialized per command. Since .cmd_sent_to_fw and
.trc_flags are only modified from inside these functions it is not
necessary to protect it with locking. Remove the superfluous locking.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the previous patch removed the only statement that sets
qla_tgt_cmd.released, remove the code that depends on that member variable
being set and the member variable itself.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The previous patch guarantees that a command is only released after the
firmware has finished processing it. Hence complain if a command is
released that is owned by the firmware.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the function qlt_abort_cmd_on_host_reset() because it can do the
following, all of which can cause a kernel crash:
- DMA unmapping while DMA is in progress.
- Call target_execute_cmd() while DMA is in progress.
- Call transport_generic_free_cmd() while the LIO core owns a command.
Instead of trying to abort a command asynchronously, set the 'aborted' flag
and handle the abort after the hardware has passed control back to the
tcm_qla2xxx driver.
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: c0cb44967b ("qla2xxx: Add Host reset handling in target mode.") # v3.18.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implementations of the .write_pending() callback functions must guarantee
that an appropriate LIO core callback function will be called immediately or
at a later time. Make sure that this guarantee is met for aborted SCSI
commands.
[mkp: typo]
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: 694833ee00 ("scsi: tcm_qla2xxx: Do not allow aborted cmd to advance.") # v4.13.
Fixes: a07100e00a ("qla2xxx: Fix TMR ABORT interaction issue between qla2xxx and TCM") # v4.5.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The test "if (!cmd)" is not useful because it is guaranteed that cmd !=
NULL. Instead of testing the cmd pointer, rely on the tag to decide
whether or not command allocation failed.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: 33e7997755 ("qla2xxx: Add support for QFull throttling and Term Exchange retry") # v3.18.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All qlt_send_term_imm_notif() callers pass '1' as second argument to this
function. Hence remove the (broken) code that depends on that second
argument having another value. Add a pr_debug() statement that prints rc to
avoid that the compiler would complain that rc has been set but is not
used.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current order for freeing memory is as follows:
- struct crc_context itself.
- struct crc_context member pointers.
Change the freeing order into the following:
- struct crc_context member pointers.
- struct crc_context itself.
Detected by Coverity.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: 50b812755e ("scsi: qla2xxx: Fix DMA error when the DIF sg buffer crosses 4GB boundary") # v5.1-rc1.
Fixes: d74595278f ("scsi: qla2xxx: Add multiple queue pair functionality.") # v4.10.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that the allocated interrupts are freed if allocating memory for
the msix_entries array fails.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clear each pointer after having freed memory such that it becomes safe to
call qla2x00_mem_free() twice.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of clearing all freed pointers at the end of qla2x00_mem_free(),
clear freed pointers immediately after having freed the memory these
pointers point at.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that Coverity complains that qla2x00_async_event() writes
outside the bounds of the mb[] arrays (MBA_IDC_AEN case).
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is important to know why a firmware command failed. Hence log 'rval'
together with the values of the mailbox registers if a firwmare command
fails.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since Coverity cannot know that rport != NULL in qla2xxx_queuecommand() and
since there is code in that function that dereferences the rport pointer,
modify qla2xxx_queuecommand() such that it fails SCSI commands if rport ==
NULL.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Testing whether a pointer is not NULL after it has been dereferenced is not
useful. Hence remove the if (fcport) test. This was detected by Coverity.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qla2x00_init_timer() is not used for I/O commands there is no need to
inline this function. Hence uninline this function.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The previous patch moved all qla2x00_is_reserved_id() callers into
qla_init.c. Hence also move the qla2x00_is_reserved_id() definition into
qla_init.c.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qla2x00_clear_loop_id() is not in the hot path, uninline it.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since all qla2x00_find_new_loop_id() calls occur in the same source file as
the definition of this function, move that function to just before its
first caller and declare it static. Convert the header above this function
into kernel-doc format.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qla2x00_set_reserved_loop_ids() only has a single caller, move it
into the source file from where it is called.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since mcmd->sess->port_name is eight bytes long, use %8phC to format that
port name instead of %phC.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery") # v4.11.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change one occurrence of "*(" into "()" and change one occurrence of
"lcoate" into "locate". Fix the reference to qla_tgt_handle_cmd_for_atio():
there has never been a function with that name.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: 75f8c1f693 ("[SCSI] tcm_qla2xxx: Add >= 24xx series fabric module for target-core") # v3.5.
Fixes: 2d70c103fd ("[SCSI] qla2xxx: Add LLD target-mode infrastructure for >= 24xx series") # v3.5.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reverts commit d16ece577b to make a clean revert of its predecessor
possible.
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix RX_TERMINATION_FORCE_ENABLE define value from 0x0089 to 0x00A9
according to MIPI Alliance MPHY specification.
Fixes: e785060ea3 ("ufs: definitions for phy interface")
Signed-off-by: Pedro Sousa <sousa@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/qedf/qedf_els.c: In function 'qedf_process_els_compl':
drivers/scsi/qedf/qedf_els.c:149:20: warning: variable 'sc_cmd' set but not used [-Wunused-but-set-variable]
drivers/scsi/qedf/qedf_els.c:148:28: warning: variable 'task_ctx' set but not used [-Wunused-but-set-variable]
drivers/scsi/qedf/qedf_els.c: In function 'qedf_send_srr':
drivers/scsi/qedf/qedf_els.c:612:6: warning: variable 'sid' set but not used [-Wunused-but-set-variable]
They are never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 8.37.25.20.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print return value of scsi_add_host on failure.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Log fcport for which upload failed.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Log the reason for start xmit failure.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print message on scsi_add_host failure.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print the fcoe_libfc_config failure and return proper failure.
Signed-off-by: Saurav Kashyap <saurav.kashyap@cavium.com>
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Comment will help in decoding the logging level.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Port ID will help in debugging.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print LBA information for underrun cases.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Printing scsi command pointer will help in crash dump analysis.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the message to display load failure.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whenever offload ramrod is issued, firmware wants driver to wait for max 5
secs, otherwise driver can initiate further corrective action. Similarly,
when termination ramrod is issued, irrespective of abortive or non-abortive
termination, driver should wait for 60 sec * max TCP-RT timeout.
[mkp: typos]
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
csiostor driver allocates per port num_online_cpus() irq vectors, so create
per-port irq affinity mask set to spread irq vectors evenly.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ELS IOCB done message should be moved to verbose logging to prevent
confusion about the error case v/s successful submission case.
[mkp: typos]
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue reported by some of the customers, who discovered
that after cable pull scenario the devices disappear and path seems to
remain in blocked state. Once the device reappears, driver does not seem to
update path to online. This issue appears because of the defer flag
creating race condition where the same session reappears. This patch fixes
this issue by indicating SCSI-ML of device lost when
qlt_free_session_done() is called from qlt_unreg_sess().
Fixes: 41dc529a46 ("qla2xxx: Improve RSCN handling in driver")
Signed-off-by: Quinn Tran <qtran@marvell.com>
Cc: stable@vger.kernel.org #4.19
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
*) Add a new *release* phy_ops invoked when the consumer relinquishes PHY
that can be used to undo the operation performed in xlate
*) Add new driver to support USB2 PHY and shared USB3 + PCIE PHY in Amlogic
G12A SoC Family.
*) Add new driver to support for Broadcom's Stingray USB PHY (Type 1 has
one super speed PHY and one high speed PHY, Type 2 has one high speed PHY)
*) Add new driver to support USB PHY in hi3660 SoC of Hisilicon
*) Add new driver to support UFS M-PHY in MediaTek SoC
*) Add new driver to support XUSB pad controller in Tegra186 SoCs
*) Add new driver to support SERDES in TI's AM654 platform
*) Add support for generation 2 USB2 PHY and gneration 3 USB2 PHY in r8a77470
to phy-rcar-gen2.c and phy-rcar-gen3-usb2.c respectively
*) Add support for PCIe QMP PHY support in msm8998 to phy-qcom-qmp.c
*) Add support for SERDES6G in phy-ocelot-serdes.c
*) Add support to set drive impedance from device tree in phy-rockchip-emmc.c
*) Add support to power up/down the VBUS voltage rail in phy-fsl-imx8mq-usb.c
*) Add support to shut off regulators that power UFS during system suspend
*) Re-design phy-rcar-gen3-usb2.c to create separate PHY instances for each
channel which helps to enable/disable interrupts for each instance
independently
*) Fix PCIe power up sequence to follow the TRM in order to ensure the DPLL &
PHY operates correctly over the entire temperature range.
*) Use devm_clk_get_optional to get optional clocks instead of adding
custom error checks
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=BAzr
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.2
*) Add a new *release* phy_ops invoked when the consumer relinquishes PHY
that can be used to undo the operation performed in xlate
*) Add new driver to support USB2 PHY and shared USB3 + PCIE PHY in Amlogic
G12A SoC Family.
*) Add new driver to support for Broadcom's Stingray USB PHY (Type 1 has
one super speed PHY and one high speed PHY, Type 2 has one high speed PHY)
*) Add new driver to support USB PHY in hi3660 SoC of Hisilicon
*) Add new driver to support UFS M-PHY in MediaTek SoC
*) Add new driver to support XUSB pad controller in Tegra186 SoCs
*) Add new driver to support SERDES in TI's AM654 platform
*) Add support for generation 2 USB2 PHY and gneration 3 USB2 PHY in r8a77470
to phy-rcar-gen2.c and phy-rcar-gen3-usb2.c respectively
*) Add support for PCIe QMP PHY support in msm8998 to phy-qcom-qmp.c
*) Add support for SERDES6G in phy-ocelot-serdes.c
*) Add support to set drive impedance from device tree in phy-rockchip-emmc.c
*) Add support to power up/down the VBUS voltage rail in phy-fsl-imx8mq-usb.c
*) Add support to shut off regulators that power UFS during system suspend
*) Re-design phy-rcar-gen3-usb2.c to create separate PHY instances for each
channel which helps to enable/disable interrupts for each instance
independently
*) Fix PCIe power up sequence to follow the TRM in order to ensure the DPLL &
PHY operates correctly over the entire temperature range.
*) Use devm_clk_get_optional to get optional clocks instead of adding
custom error checks
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (51 commits)
dt-bindings: phy-qcom-qmp: Tweak qcom,msm8998-qmp-ufs-phy
dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-pcie-phy
phy: Add usb phy support for hi3660 Soc of Hisilicon
dt-bindings: phy: Add support for HiSilicon's hi3660 USB PHY
scsi: phy: mediatek: fix typo in author's email address
phy: ocelot-serdes: Add support for SERDES6G muxing
phy: fsl-imx8mq-usb: add support for VBUS power control
dt-bindings: phy-imx8mq-usb: add optional vbus supply regulator
phy: qcom-qmp: Add msm8998 PCIe QMP PHY support
phy: ti: am654-serdes: Support all clksel values
phy: ti: Add a new SERDES driver for TI's AM654x SoC
dt-bindings: phy: ti: Add dt binding documentation for SERDES in AM654x SoC
phy: core: Invoke pm_runtime_get_*/pm_runtime_put_* before invoking reset callback
phy: core: Add *release* phy_ops invoked when the consumer relinquishes PHY
phy: phy-meson-gxl-usb2: get optional clock by devm_clk_get_optional()
phy: socionext: get optional clock by devm_clk_get_optional()
phy: qcom-qusb2: get optional clock by devm_clk_get_optional()
phy: phy-mtk-tphy: get optional clock by devm_clk_get_optional()
phy: renesas: rcar-gen3-usb2: enable/disable independent irqs
phy: renesas: rcar-gen3-usb2: Use pdev's device pointer on dev_vdbg()
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAly8rGYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGmZMH/1IRB0E1Qmzz8yzw
wj79UuRGYPqxDDSWW+wNc8sU4Ic7iYirn9APHAztCdQqsjmzU/OVLfSa3JhdBe5w
THo7pbGKBqEDcWnKfNk/21jXFNLZ1vr9BoQv2DGU2MMhHAyo/NZbalo2YVtpQPmM
OCRth5n+LzvH7rGrX7RYgWu24G9l3NMfgtaDAXBNXesCGFAjVRrdkU5CBAaabvtU
4GWh/nnutndOOLdByL3x+VZ3H3fIBnbNjcIGCglvvqzk7h3hrfGEl4UCULldTxcM
IFsfMUhSw1ENy7F6DHGbKIG90cdCJcrQ8J/ziEzjj/KLGALluutfFhVvr6YCM2J6
2RgU8CY=
=CfY1
-----END PGP SIGNATURE-----
Merge tag 'v5.1-rc6' into for-5.2/block
Pull in v5.1-rc6 to resolve two conflicts. One is in BFQ, in just a
comment, and is trivial. The other one is a conflict due to a later fix
in the bio multi-page work, and needs a bit more care.
* tag 'v5.1-rc6': (770 commits)
Linux 5.1-rc6
block: make sure that bvec length can't be overflow
block: kill all_q_node in request_queue
x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
mm/kmemleak.c: fix unused-function warning
init: initialize jump labels before command line option parsing
kernel/watchdog_hld.c: hard lockup message should end with a newline
kcov: improve CONFIG_ARCH_HAS_KCOV help text
mm: fix inactive list balancing between NUMA nodes and cgroups
mm/hotplug: treat CMA pages as unmovable
proc: fixup proc-pid-vm test
proc: fix map_files test on F29
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
mm: swapoff: shmem_unuse() stop eviction without igrab()
mm: swapoff: take notice of completion sooner
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
mm: swapoff: shmem_find_swap_entries() filter out other types
slab: store tagged freelist for off-slab slabmgmt
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
path to correctly return status on error.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXLtrDSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYh/AQDe6Jf7
jU/VKsir8r74Uy1gHw9wXkmcgzKeTzHErEyvGgD9HqEfAKUWr0YlMqfKqnQZUhUc
TPokv5u1u2xc/ba+nuo=
=VutB
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
path to correctly return status on error"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: aic7xxx: fix EISA support
Revert "scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO"
scsi: core: set result when the command cannot be dispatched
Instead of relying on the now removed NULL argument to
pci_alloc_consistent, switch to the generic DMA API, and store the struct
device so that we can pass it.
Fixes: 4167b2ad51 ("PCI: Remove NULL device handling from PCI DMA API")
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch clears FC_RP_STARTED flag during logoff, because of this
re-login(flogi) didn't happen to the switch.
This reverts commit 1550ec458e.
Fixes: 1550ec458e ("scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO")
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Reviewed-by: Hannes Reinecke <hare@#suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in a kernel message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warning:
drivers/scsi/lpfc/lpfc_init.c:13091:1: warning:
symbol 'lpfc_sli4_oas_verify' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a couple of spelling mistakes in some kernel info and notice
messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a couple of spelling mistakes in some kernel alert messages. Fix
these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the qedf_dbg_* family of functions can overrun the end of the
source string if it is less than the destination buffer length because of
the use of a fixed sized memcpy. Remove the memset/memcpy calls to nfunc
and just use func instead as it is always a null terminated string.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: 61d8658b4a ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The phy code was using implicit sequencing between the PHY driver
and the UFS driver to implement certain hardware requirements.
Specifically, the PHY reset register in the UFS controller needs
to be deasserted before serdes start occurs in the PHY.
Before this change, the code was doing this by utilizing the two
phy callbacks, phy_init() and phy_poweron(), as "init step 1" and
"init step 2", where the UFS driver would deassert reset between
these two steps.
This makes it challenging to power off the regulators in suspend,
as regulators are initialized in init, not in poweron(), but only
poweroff() is called during suspend, not exit().
For UFS, move the actual firing up of the PHY to phy_poweron() and
phy_poweroff() callbacks, rather than init()/exit(). UFS calls
phy_poweroff() during suspend, so now all clocks and regulators for
the phy can be powered down during suspend.
QMP is a little tricky because the PHY is also shared with PCIe and
USB3, which have their own definitions for init() and poweron(). Rename
the meaty functions to _enable() and _disable() to disentangle from the
PHY core names, and then create two different ops structures: one for
UFS and one for the other PHY types.
In phy-qcom-ufs, remove the 'is_powered_on' and 'is_started' guards,
as the generic PHY code does the reference counting. The
14/20nm-specific init functions get collapsed into the generic power_on()
function, with the addition of a calibrate() callback specific to 14/20nm.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move the PHY reset from ufs-qcom into the respective PHYs. This will
allow us to merge the two phases of UFS PHY initialization.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Expose a reset controller that the phy will later use to control its
own PHY reset in the UFS controller. This will enable the combining
of PHY init functionality into a single function.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When SCSI blk-mq is enabled, there is a bug in handling errors in
scsi_queue_rq. Specifically, the bug is not setting result field of
scsi_request correctly when the dispatch of the command has been
failed. Since the upper layer code including the sg_io ioctl expects to
receive any error status from result field of scsi_request, the error is
silently ignored and this could cause data corruptions for some
applications.
Fixes: d285203cf6 ("scsi: add support for a blk-mq based I/O path.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jaesoo Lee <jalee@purestorage.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit 84961f28e9 ("[SCSI] Don't add scsi_device for devices that return
PQ=1, PDT=0x1f") returns SCSI_SCAN_TARGET_PRESENT if inquiry returns PQ=1,
and PDT = 0x1f. However, from the scsi spec, it seemed setting PQ=1, and
PDT to the type it is capable to support, can also mean the device is not
connected. E.g. we see an IBM/2145 returns PQ=1 and PDT=0 for a non-mapped
lun (details attached at the end).
This patch changes the check condition a bit, so the check don't require
PTD to be 0x1f when PQ=1.
$ echo 0 0 1 > /sys/class/scsi_host/host1/scan
[ 2483.722186] scsi 1:0:0:1: scsi scan: INQUIRY pass 1 length 36
[ 2483.725687] scsi 1:0:0:1: scsi scan: INQUIRY successful with code 0x0
[ 2483.729171] scsi 1:0:0:1: scsi scan: INQUIRY pass 2 length 109
[ 2483.732481] scsi 1:0:0:1: scsi scan: INQUIRY successful with code 0x0
[ 2483.735911] scsi 1:0:0:1: Direct-Access IBM 2145 0000 PQ: 1 ANSI: 6
[ 2483.741282] scsi 1:0:0:1: Attached scsi generic sg2 type 0
$ tail /proc/scsi/scsi
Attached devices:
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: 2145 Rev: 0000
Type: Direct-Access ANSI SCSI revision: 06
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: 2145 Rev: 0000
Type: Direct-Access ANSI SCSI revision: 06
Host: scsi1 Channel: 00 Id: 00 Lun: 01
Vendor: IBM Model: 2145 Rev: 0000
Type: Direct-Access ANSI SCSI revision: 06
$ lsscsi
[0:0:0:0] disk IBM 2145 0000 /dev/sdb
[1:0:0:0] disk IBM 2145 0000 /dev/sda
[1:0:0:1] disk IBM 2145 0000 -
Signed-off-by: Li Zhong <lizhongfs@gmail.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warning:
drivers/scsi/megaraid/megaraid_sas_base.c:4652:1: warning:
symbol 'megasas_host_device_list_query' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If UFS device responds an unknown request response code, we can not know
what it was via logs because the code is replaced by "DID_ERROR << 16"
before log printing.
Fix this to provide precise request response code information for easier
issue breakdown.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To support vlan and bridge devices first find route using ifindex 0, if
route is not found through net device associated with input scsi host then
find route using ifindex of net device.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cxgbi_device_find_by_netdev() returns NULL then find cxgbi device by MAC
address.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_device's refcount is always grabbed in IO path.
Turns out it isn't necessary, because blk_queue_cleanup() will drain any
in-flight IOs, then cancel timeout/requeue work, and SCSI's requeue_work is
canceled too in __scsi_remove_device().
Also scsi_device won't go away until blk_cleanup_queue() is done.
So don't hold the refcount in IO path, especially the refcount isn't
required in IO path since blk_queue_enter() / blk_queue_exit() is
introduced in the legacy block layer.
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org,
Cc: Martin K . Petersen <martin.petersen@oracle.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>,
Cc: jianchao wang <jianchao.w.wang@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The qla2x00_set_fcport_state() function is not in the hot path so move its
definition from a .h into a .c file.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Casting a void pointer into another pointer before assigning the pointer to
a variable is not useful. Hence remove such casts.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 'data_work' and 'data_work_free' member variables are set but never
used. Hence remove both member variables. See also commit 6bcbb3174c
("qla2xxx: Fix incorrect tcm_qla2xxx_free_cmd use during TMR ABORT (v2)").
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The <linux/io-64-nonatomic-lo-hi.h> header file is included because of the
readq() macro. Since that macro is only used in qla_nx.c, move that include
statement into qla_nx.c.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qla24xx_build_scsi_crc_2_iocbs() is only used inside a single source
file, declare this function static.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce the size of the qla2xxx kernel module by moving an array definition
from a .h into a .c file.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Improve source code readability by inserting spaces where these are
required according to the coding standard. This patch only inserts
whitespace and does not make any other changes.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Improve source code readability by following the Linux kernel coding style
for pointer types. This patch only changes whitespace.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch improves readability of the qla2xxx source code.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most but not all code in the qla2xxx driver uses tabs for indentation.
Make the qla2xxx code easier to read by using tabs consistently for
indentation. This patch improves conformance with the Linux kernel coding
style.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we print expander PHY indexes in a mix of decimal and hex.
It is more consistent and also more convenient to read decimal, so
make this change.
We use width of 2 for expander and 1 for root PHYs prints.
Some lines which were needlessly spilling multiple lines are unified.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we discover the PHY is empty in sas_rediscover_dev(), the PHY
information (like negotiated linkrate) is not updated.
As such, for a user examining sysfs for that PHY, they would see
incorrect values:
root@(none)$ cd /sys/class/sas_phy/phy-0:0:20
root@(none)$ more negotiated_linkrate
3.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
3.0 Gbit
So fix this, simply discover the PHY again, even though we know it's empty;
in the above example, this gives us:
root@(none)$ more negotiated_linkrate
Phy disabled
We must do this after unregistering the device associated with the PHY
(in sas_unregister_devs_sas_addr()).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the SAS spec, an expander device shall transmit BROADCAST
(CHANGE) from at least one phy in each expander port other than the
expander port that is the cause for transmitting BROADCAST (CHANGE).
As such, for when the link is lost for a root PHY attached to an expander
PHY, we get no broadcast event.
This causes an issue for libsas, in that we will not revalidate the domain
for these events.
As a solution, for when a root PHY is formed or deformed from a root port,
insert a broadcast event to trigger a domain revalidation.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an expander PHY which was part of a wideport disconnects, we would see
a log like this from sas_rediscover():
[ 39.695554] sas: phy20 part of wide port with phy16
Here, phy20 is the PHY that disconnected, and phy16 is the lowest indexed
member PHY of the wideport.
The log implies the phy20 is still part of the wideport with phy16, so is
misleading or, at least, vague.
Improve the logs in SAS rediscovery by removing this log and adding a log
in sas_rediscover_dev() to tell what's really going on.
While we're at it, also make the logs in sas_find_bcast_dev() more
informative (and more consistent with the reset of the expander logs).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently for fixing the linkrate matching during discovery such that the
linkrate of a SATA PHY does not exceed min pathway to initiator, we set the
SATA PHY programmed min linkrate to the same value as the programmed max
linkrate.
This is unnecessary, and we should be able to keep the same programmed min
linkrate if it is already lower than this new max programmed linkrate.
This patch makes that change.
In effect, this will not make much difference since we generally will
negotiate a linkrate at the programmed max linkrate, and the programmed min
linkrate will have no impact.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many times we use 8 for SAS address length, while we already have a macro
for this - SAS_ADDR_SIZE.
Replace instances of this with the macro. However, don't touch the SAS
address array sizes sas.h, as these are defined according to the SAS spec.
Some missing whitespaces are also added, and whitespace indentation
in sas_hash_addr() is also fixed (see sas_hash_addr()).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----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=cISy
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190412' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Set of fixes that should go into this round. This pull is larger than
I'd like at this time, but there's really no specific reason for that.
Some are fixes for issues that went into this merge window, others are
not. Anyway, this contains:
- Hardware queue limiting for virtio-blk/scsi (Dongli)
- Multi-page bvec fixes for lightnvm pblk
- Multi-bio dio error fix (Jason)
- Remove the cache hint from the io_uring tool side, since we didn't
move forward with that (me)
- Make io_uring SETUP_SQPOLL root restricted (me)
- Fix leak of page in error handling for pc requests (Jérôme)
- Fix BFQ regression introduced in this merge window (Paolo)
- Fix break logic for bio segment iteration (Ming)
- Fix NVMe cancel request error handling (Ming)
- NVMe pull request with two fixes (Christoph):
- fix the initial CSN for nvme-fc (James)
- handle log page offsets properly in the target (Keith)"
* tag 'for-linus-20190412' of git://git.kernel.dk/linux-block:
block: fix the return errno for direct IO
nvmet: fix discover log page when offsets are used
nvme-fc: correct csn initialization and increments on error
block: do not leak memory in bio_copy_user_iov()
lightnvm: pblk: fix crash in pblk_end_partial_read due to multipage bvecs
nvme: cancel request synchronously
blk-mq: introduce blk_mq_complete_request_sync()
scsi: virtio_scsi: limit number of hw queues by nr_cpu_ids
virtio-blk: limit number of hw queues by nr_cpu_ids
block, bfq: fix use after free in bfq_bfqq_expire
io_uring: restrict IORING_SETUP_SQPOLL to root
tools/io_uring: remove IOCQE_FLAG_CACHEHIT
block: don't use for-inside-for in bio_for_each_segment_all
Do some minor tidy-up.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we call hisi_sas_softreset_ata_disk() in
hisi_sas_I_T_nexus_reset().
If this fails for open reject reason, there is no reason to fail the IT
nexus reset, so only fail for TMF_RESP_FUNC_FAILED.
Some other strings spilled over multiple lines are reunited.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the function of hisi_sas_init_device(), we added ops->hardreset() to
clear affiliation of STP target port or handle [STP pending] state.
Function hisi_sas_init_device() will be called when a device is found or
during controller reset. At controller reset, we call
hisi_sas_init_device() to re-init the disks, so calling hardreset() is
unnecessary and it also will cause some delay at controller reset.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to switch HW all error handling from PCI AER to MSI interrupt
due to non-standard PCI implementation. All HW errors which were being
reported through PCI AER can be reported through MSI interrupt also.
Do two things to complete the switch:
1. Notify FW to switch to MSI handling through ACPI DSM.
2. Add MSI handling for some hw errors, ECC errors and poison errors (we
also call some of them AXI reuser error). They were handled only through
PCI AER before.
For old FW reporting PCI AER events, the PCI AER handler will see that the
driver on longer support AER, and will leave the device in offlined state,
which is safe.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit 8b8d665315 ("scsi: hisi_sas: make SAS address of SATA disks
unique"), we ensured that each SATA disk in the system has a unique SAS
address, even if it is fake. That was for v2 hw.
Add this for v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_init_device(), the log is as follows when error for
hardreset:
hisi_sas_v3_hw 0000:74:02.0: SATA disk hardreset fail: 0xffffffed
Actually if hardreset failed, its return value is negative, so change the
print format from %x to %d.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit efdcad62e7 ("scsi: hisi_sas: Set PHY linkrate when
disconnected"), we use the sas_phy_data.enable flag to track whether the
PHY was enabled or not, so that we know if we should set the PHY negotiated
linkrate at SAS_LINK_RATE_UNKNOWN or SAS_PHY_DISABLED.
However, it is not proper to use sas_phy_data.enable, since it is only set
when libsas attempts to set the PHY disabled/enabled; hence, it may not
even have an initial value.
As a solution to this problem, introduce hisi_sas_phy.enable to track
whether the PHY is enabled or not, so that we can set the negotiated
linkrate properly when the PHY comes down.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there are two scenarioes which may cause PHY state of hardware
(which is 0) is inconsistent with the state held in software:
- Unplug SAS wire before get_phys_state when SAS controller reset, then the
interrupts of phy down are ignored, phy state is 0 before reset, and it
also gets 0 after reset, so phy down doesn't occur even if unplugged SAS
wire;
- For v3 hw later version, it will close bus when 2 bit ECC error occurs.
So if unplug SAS wire at that time, interrupts of phy down also not
occur. So at last it will cause host reset. It also get phy state 0
before and after reset, the same issue occurs.
To solve it, use hisi_sas_phy_down() directly in rescan topology function.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add host reset interface to make it easier for testing the host reset
feature.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have a few submissions for 5.2 that depend on fixes merged post
5.1-rc1. Merge the fixes branch into queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the FC-NVMe driver is leverating the SCSI FC transport class to
access the remote ports. Which means that all FC-NVMe remote ports will be
visible to the fc transport layer, but due to missing definitions the port
roles will always be 'unknown'. This patch adds the missing definitions to
the fc transport class to that the port roles are correctly displayed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The error return path via label rel_resource checks for a non-null skb
before free'ing it. However, skb is always null at this exit path, so the
null check and the free are redundant and can be removed. Removing this
allows the original goto's to rel_resource to be cleaned up; the first can
be replaced by a return of -EINVAL, the second can be replaced by a more
appropriate -ENOMEM return and fix a memory leak by freeing csk->atid.
Addresses-Coverity: ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, an empty disk->events field tells the block layer not to
forward media change events to user space. This was done in commit
7c88a168da ("block: don't propagate unlisted DISK_EVENTs to userland")
in order to avoid events from "fringe" drivers to be forwarded to user
space. By doing so, the block layer lost the information which events
were supported by a particular block device, and most importantly,
whether or not a given device supports media change events at all.
Prepare for not interpreting the "events" field this way in the future
any more. This is done by adding an additional field "event_flags" to
struct gendisk, and two flag bits that can be set to have the device
treated like one that had the "events" field set to a non-zero value
before. This applies only to the sd and sr drivers, which are changed to
set the new flags.
The new flags are DISK_EVENT_FLAG_POLL to enforce polling of the device
for synchronous events, and DISK_EVENT_FLAG_UEVENT to tell the
blocklayer to generate udev events from kernel events.
In order to add the event_flags field to struct gendisk, the events
field is converted to an "unsigned short"; it doesn't need to hold
values bigger than 2 anyway.
This patch doesn't change behavior.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When tag_set->nr_maps is 1, the block layer limits the number of hw queues
by nr_cpu_ids. No matter how many hw queues are used by virtio-scsi, as it
has (tag_set->nr_maps == 1), it can use at most nr_cpu_ids hw queues.
In addition, specifically for pci scenario, when the 'num_queues' specified
by qemu is more than maxcpus, virtio-scsi would not be able to allocate
more than maxcpus vectors in order to have a vector for each queue. As a
result, it falls back into MSI-X with one vector for config and one shared
for queues.
Considering above reasons, this patch limits the number of hw queues used
by virtio-scsi by nr_cpu_ids.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only include those header files that are needed by the code in this source
file.
[mkp: include build fix from Bart for SPARC]
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If scsi cmd sglist is not suitable for DDP then csiostor driver uses
preallocated buffers for DDP, because of this data copy is required from
DDP buffer to scsi cmd sglist before calling ->scsi_done().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that resources are only unregistered after the users of these
resources have been unregistered. Only unregister the character device if
registration of it succeeded.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If module initialization fails after the character device has been
registered, unregister the character device. Additionally, avoid
duplicating error path code.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Fixes: 6a03b4cd78 ("[SCSI] qla2xxx: Add char device to increase driver use count") # v2.6.35.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes the code easier to read but does not change any
functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make qla2x00_process_response_queue() easier to read by splitting this
function. This patch does not change any functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the SCSI host template definition after the definition of the
functions that it references. Remove the forward declarations that became
unnecessary by that change. This patch does not change any functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that sparse complains that a declaration is missing.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make the code easier to read by avoiding to use a hard-coded constant. This
patch does not change any functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qla2xxx_queuecommand() no longer takes the SCSI host lock, remove a
comment that refers to the host lock.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make qla2x00_get_host_fabric_name() slightly faster by changing a stack
array into a static array. Declare that array const now that the
wwn_to_u64() argument pointer has been declared const.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in a ql_log message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to recognize FPIN ELS's that are received. When
one is received, the fc transport will be called to handle the the FPIN.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new event type - an FPIN event.
Add a new routine, fc_host_fpin_rcv(), that lldd's call when an FPIN is
received. The routine processes the fpin payload. For now, the routine
only logs an FPIN event.
Signed-off-by: Muneendra <muneendra.kumar@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two routines generating transport events that do the same thing
with only a couple of values set differently.
Refactor so there's a single routine doing the netlink operations to send
the event. All the differences are passed as arguments. Export the symbol
so the generic routine can be called by llds.
Modify the existing two event routines to use the helper.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the following compiler warning is reported with
CONFIG_NVME_FC=n:
drivers/scsi/lpfc/lpfc_nvme.c:2140:1: warning: 'lpfc_nvme_lport_unreg_wait' defined but not used [-Wunused-function]
lpfc_nvme_lport_unreg_wait(struct lpfc_vport *vport,
^~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 3999df75bc ("scsi: lpfc: Declare local functions static")
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114996 ("Missing break in switch")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114988 ("Missing break in switch")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114983 ("Missing break in switch")
Addresses-Coverity-ID: 114984 ("Missing break in switch")
Addresses-Coverity-ID: 114985 ("Missing break in switch")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that, in this particular case, I replaced "Drop thru" with
"fall through" annotations, which is what GCC is expecting to find.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that, in this particular case, I replaced "Drop thru" with a
"fall through" annotation, which is what GCC is expecting to find.
Addresses-Coverity-ID: 114976 ("Missing break in switch")
Addresses-Coverity-ID: 114977 ("Missing break in switch")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114978 ("Missing break in switch")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that, in this particular case, I placed all the "Phase N - ..."
comments on the same line as its corresponding switch case. The same
way in which similar comments appear in drivers/scsi/ppa.c. This makes
it possible to place the "fall through" annotations at the bottom of
each switch case, which is what GCC is expecting to find.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056538 ("Missing break in switch")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that I replaced "Fall through !!!" with a "fall through"
annotation, which is what GCC is expecting to find.
Addresses-Coverity-ID: 114971 ("Missing break in switch")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1357387 ("Missing break in switch")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that, in some cases, I replaced "FALLTHROUGH" with a "fall through"
annotation and then placed it at the bottom of the corresponding switch
case, which is what GCC is expecting to find.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
All mmiowb() invocations have been removed, so there's no need to keep
banging on about it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In preparation for using coccinelle to remove all mmiowb() instances
from drivers, remove all trailing comments since they won't be picked up
by spatch later on and will end up being preserved in the code.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently support for 64-bit sector_t and blkcnt_t is optional on 32-bit
architectures. These types are required to support block device and/or
file sizes larger than 2 TiB, and have generally defaulted to on for
a long time. Enabling the option only increases the i386 tinyconfig
size by 145 bytes, and many data structures already always use
64-bit values for their in-core and on-disk data structures anyway,
so there should not be a large change in dynamic memory usage either.
Dropping this option removes a somewhat weird non-default config that
has cause various bugs or compiler warnings when actually used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The memory return by kzalloc() has already be set to zero, so remove
useless memset(0).
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds an additional PHY initialization, required for M31 PHY when
used with Cadence UFS HC. A new compatible string has been added for this
purpose.
[mkp: nuke superfluous status return]
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pointer value is initialized as &hba->vreg_info, and it's never
changed. It's not necessary to check the pointer is null or not.
Signed-off-by: Zeng Guangyue <zengguangyue@hisilicon.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/qedf/qedf_fip.c: In function 'qedf_fcoe_send_vlan_req':
drivers/scsi/qedf/qedf_fip.c:22:6: warning:
variable 'fr_len' set but not used [-Wunused-but-set-variable]
It's never used since introduction and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename the functions pm8001_chip_is_our_interupt,
pm80xx_chip_is_our_interupt and function pointer is_our_interrupt to fix
spelling mistakes.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When macro PM8001_USE_MSIX is defined there are redundant dead code calls
to pm8001_chip_intx_interrupt_{enable|disable} and pm8001_cr32.
Clean this up for the defined PM8001_USE_MSIX and undefined
PM8001_USE_MSIX cases.
[mkp: squashed two patches]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch converts driver wait time from using msleep to
wair_event_timeout to prevent race condition.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allows driver to unload using "modprobe -r" when FC-NVMe LUNs
are connected.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch sets remote_port_devloss value to 0. This indicates to FC-NVMe
transport that driver is unloading and transport should not retry.
Fixes: e476fe8af5 ("scsi: qla2xxx: Fix unload when NVMe devices are configured")
Cc: stable@vger.kernel.org
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clean up fcport list and loopid in one place and iterate through for loop.
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add mutex protection to prevent driver from freeing the FW dump buffer
while the extraction is in progress.
[mkp: commit desc]
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If fw dump buffer size changes and there is an existing fw dump, then save
the old dump in the newly allocated buffer.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Recent ISPs have larger and more complex flash-write semantics
(secure-access and signing). The BSG interfaces support these semantics for
all ISPs and is exclusively used by QLogic user-space tools. Limit
flash-write operations to ISPs <= 25xx.
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit e6f77540c0 ("scsi: qla2xxx: Fix an integer overflow in sysfs
code") incorrectly set 'optrom_region_size' to 'start+size', which can
overflow option-rom boundaries when 'start' is non-zero. Continue setting
optrom_region_size to the proper adjusted value of 'size'.
Fixes: e6f77540c0 ("scsi: qla2xxx: Fix an integer overflow in sysfs code")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abort thread wakeups, on some wqe types, are not happening. The thread
wakeup logic is dependent upon the LPFC_DRIVER_ABORTED flag. However, on
these wqes, the completion handler running prior to the io completion
routine ends up clearing the flag.
Rework the wakeup logic to look at a non-null waitq element which must be
set if the abort thread is waiting. This is reverting the change in the
indicated patch.
Fixes: c2017260ee ("scsi: lpfc: Rework locking on SCSI io completion")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce the default VMbus channel ring buffer size for storvsc SCSI devices
from 1 Mbyte to 128 Kbytes. Measurements show that ring buffer sizes above
128 Kbytes do not increase performance even at very high IOPS rates, so
don't waste the memory. Also remove the dependence on PAGE_SIZE, since the
ring buffer size should not change on architectures where PAGE_SIZE is not
4 Kbytes.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the number of sub-channels offered by Hyper-V is >= the number of CPUs
in the VM, calculate the correct number of sub-channels. The current code
produces one too many.
This scenario arises only when the number of CPUs is artificially
restricted (for example, with maxcpus=<n> on the kernel boot line), because
Hyper-V normally offers a sub-channel count < number of CPUs. While the
current code doesn't break, the extra sub-channel is unbalanced across the
CPUs (for example, a total of 5 channels on a VM with 4 CPUs).
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Blacklist "Universal Xport" LUN. It's used for in-band storage array
management. Also add model to the rdac dh family.
Cc: Martin Wilck <mwilck@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: NetApp RDAC team <ng-eseries-upstream-maintainers@netapp.com>
Cc: Christophe Varoqui <christophe.varoqui@opensvc.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Cc: DM ML <dm-devel@redhat.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With FC-NVMe enabled, driver does not support T10 DIF/DIX. This patch
disables T10-PI information when ql2xnvmeenable is set.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch increases max_sgl_segments value from 128 to the maximum
supported which is 1024. Increasing max_sgl_segments will allow the driver
to support larger I/O sizes
[mkp: commit desc tweak]
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver maintains state machine for processing and completing switch
commands. This patch resets FCF_ASYNC_{SENT|ACTIVE} flag to indicate if the
previous command is active or sent, in order for next GPSC command to
advance the state machine.
[mkp: commit desc typo]
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch sets QPair pointer to NULL to prevent abort command racing ahead
of normal command completion handling during scsi_done call.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch tries to address race condition between abort handler and
completion handler. When scsi command result is set by both abort and
completion handler, scsi_done() is only called after refcount on SRB
structure goes to zero. The abort handler sets this result prematurely even
when the refcount is non-zero value. Fix this by setting SCSI cmd->result
before scsi_done() is called.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that a kernel warning appears when smp_processor_id() is
called with preempt debugging enabled.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove those functions that are not called from outside the removed
functions.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but avoids that the compiler
complains about set-but-not-used variables when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arrays should be defined in .c files instead of in a header file. This
patch reduces the size of the lpfc kernel module.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler warns about missing fall-through
annotation when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoid that smatch complains about misleading indentation.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing declarations
when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
"<name>-fixed-regulator" device tree property can be safely removed because
below things are fixed or resolved,
1. "<name>-max-microamp" becomes optional property: Undefined
"<name>-max-microamp" will not cause initialization fail if
"<name>-fixed-regulator" is not defined.
2. Current switching operation (by regulator_set_load) now has rules:
Regulators will have undefined current limit if "<name>-fixed-regulator"
is not defined. But this is safe because only regulator which has
configured current limit from "<name>-max-microamp" property is allowed
to change its load.
Although "<name>-fixed-regulator" is not used in any dt-bindings in tree,
this patch is still safe for regulators already defined
"<name>-fixed-regulator". To be more clear, if a regulator defined
"<name>-fixed-regulator" before, the behavior difference after this patch
is,
1. "<name>-max-microamp":
If a regulator defined "<name>-fixed-regulator", it is not necessary
to define "<name>-max-microamp" property in device tree and it is
expected to have an undefined current limit, i.e., "max_uA" field
is zero in struct ufs_vreg. This is exactly the same as patched.
2. "vcc-supply-1p8" or volatge range settings:
* For vcc, vccq or vccq2, these three regulators shall not define
"<name>-fixed-regulator" because defining it will lead to
undefined voltage range and thus voltage switching will be
unexpected.
* For other regulators with undefined voltage range, voltage range
will be still undefined after patched.
Therefore this patch is safe for all existed regulators with
"<name>-fixed-regulator" property already defined.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In dt-bindings for ufs, "<name>-max-microamp" property indicates current
limit and is mandatory if "<name>-fixed-regulator" is not defined on a
specified regulator.
However, in some platforms, regulators without "<name>-fixed-regulator"
property may not need to define their current limit because they may want
to define voltage range only for proper voltage switching in different
power modes, especially for vcc, vccq or vccq2.
Currently missing "<name>-max-microamp" property in device tree will lead
initialization to fail, thus such limitation shall be resolved to tolerate
this kind of regulators.
After resolving this, regulators without "<name>-max-microamp" property
will have undefined "max current" value, i.e., zero value in "max_uA" field
in struct ufs_vreg. Because we do bypass current switching operation (by
regulator_set_load) in case of undefined current limit, this patch shall be
safe.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a regulator has "<name>-fixed-regulator" property in device
tree, it will skip current limit initialization. This lead to a zero
"max_uA" value in struct ufs_vreg.
However, "regulator_set_load" operation shall be required on regulators
which have valid current limits, otherwise a zero "max_uA" set by
"regulator_set_load" may cause unexpected behavior when this regulator is
enabled or set as high power mode.
Similarly, in device's icc_level configuration flow, the target icc_level
shall be updated if regulator also has valid current limit, otherwise a
wrong icc_level will be calculated by zero "max_uA" and thus causes
unexpected results after it is written to device.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For regulators used by UFS, vcc, vccq and vccq2 will have voltage range
initialized by ufshcd_populate_vreg(), however other regulators may have
undefined voltage range if dt-bindings have no such definition.
In above undefined case, both "min_uV" and "max_uV" fields in ufs_vreg
struct will be zero values and these values will be configured on
regulators in different power modes.
Currently this may have no harm if both "min_uV" and "max_uV" always keep
"zero values" because regulator_set_voltage() will always bypass such
invalid values and return "good" results.
However improper values shall be fixed to avoid potential bugs. Simply
bypass voltage configuration if voltage range is not defined.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two fields related to regulator current limit in struct ufs_vreg:
"min_uA" and "max_uA".
"max_uA" is probed by "<name>-max-microamp" property from device tree and
used for
- regulator_set_load operations
- icc_level configuration in device
However "min_uA" field is not used anywhere, thus we can remove it.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The rc variable is not needed in bnx2fc_abts_cleanup(). Remove it and
just return SUCCESS.
[mkp: commit desc]
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nvm_image is a large struct qedi_nvm_iscsi_image object of over 24K so
don't declare it on the stack just for a sizeof requirement; use sizeof on
struct qedi_nvm_iscsi_image instead.
Fixes: c77a2fa3ff ("scsi: qedi: Add the CRC size within iSCSI NVM image")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- lport was getting used without initialization, initialize it to fix a
warning.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Handle refcount of rdata during error conditions.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Here is the relevant logs for the problem we are solving:
qedf_flush_active_ios:1707]:3: Flush active i/o's num=0x17 fcport=0xffff948168fbcc80 port_id=0x550200 scsi_id=0.
qedf_flush_active_ios:1708]:3: Locking flush mutex.
qedf_flush_active_ios:1758]:3: Not outstanding, xid=0xaaf, cmd_type=3 refcount=1.
qedf_flush_active_ios:1896]:3: Flushed 0x16 I/Os, active=0x1.
qedf_flush_active_ios:1901]:3: Flushed 0x16 I/Os, active=0x1 cnt=60.
qedf_send_rrq:295]:3: Sending RRQ orig io = ffffb48b8f7d7158, orig_xid = 0xaaf
qedf_initiate_els:37]:3: Sending ELS
qedf_initiate_els:68]:3: initiate_els els_req = 0xffffb48b8f6d3098 cb_arg = ffff948fd5e4de80 xid = 4c6
qedf_init_mp_req:2172]:3: Entered.
qedf_init_mp_task:727]:3: Initializing MP task for cmd_type=4
qedf_initiate_els:134]:3: Ringing doorbell for ELS req
qedf_flush_active_ios:1901]:3: Flushed 0x16 I/Os, active=0x2 cnt=20.
qedf_cmd_timeout:96]:3: ELS timeout, xid=0x4c6.
qedf_rrq_compl:186]:3: Entered.
qedf_rrq_compl:204]:3: rrq_compl: orig io = ffffb48b8f7d7158, orig xid = 0xaaf, rrq_xid = 0x4c6, refcount=1
qedf_flush_active_ios:1935]:3: Unlocking flush mutex.
qedf_upload_connection:1579]:3: Uploading connection port_id=550200.
We found an ABTS command for which CMD_OUTSTANDING was cleared (line 3).
For this command, delayed send_rrq was queued, but would take 10 secs to
execute. Adding capability to detect that (based on io_req->state that is
being introduced), and attempt to cancel rrq_work. If we succeed, we drop
the reference and free the io_req. If we cannot, then the els will get sent
out and we will wait for 10 secs for it to complete.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cmd_type is over written to QEDF_CLEANUP during cleanup, so check for
tm_flags.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- The flag will help in to figure out if io_req is cleaned or not.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Command is already completed with underrun so no need to send ABTS.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- I/Os, aborts and tmf should not be queued if flush is in progress.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Check proper values before servicing CVL.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fc_rport_priv structure is reference counted, so we need to ensure that
the reference is increased before accessing the structure.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On completions where we do not have a bad scsi_cmnd pointer we should
return before the the label lest we do a double kref_put.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Wait for all the connections to get uploaded.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Check the validity of various pointers before processing.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
test_bit() is atomic, test_bit() || test_bit() is not. So protect
consecutive bit tests with a lock to avoid races.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fc_rport_create() needs to be called with disc_mutex held. And we should
re-assign the 'rdata' pointer in case it got changed.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qedf_xmit() calls fc_rport_lookup(), but discards the returned rdata
structure almost immediately without decreasing the refcount. This leads
to a refcount leak and the rdata never to be freed.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Check if link is UP before sending and processing any packets on wire.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When receiving an unsolicited frame we could crash on a list traversal in
fc_rport_lookup while searching the rport which is associated with our
lport.
Initialize the lport's discovery node after allocating the lport in
__qedf_probe().
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Correct memory barriers to make sure all cmnds are flushed.
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- If a TMF and cleanup are issued at the same time they could cause a call
trace if issued against the same xid as the io_req->tm_done completion
is used for both.
- Set and clear cleanup bit in cleanup routine.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An I/O can be in any state when flush is called, it can be in abort,
waiting for abort, RRQ send and waiting or TMF send.
- HZ can be different on different architecture, correctly set abort
timeout value.
- Flush can complete the I/Os prematurely, handle refcount for aborted
I/Os and for which RRQ is pending.
- Differentiate LUN/TARGET reset, as cleanup needs to be send to firmware
accordingly.
- Add flush mutex to sync cleanup call from abort and flush routine.
- Clear abort/outstanding bit on timeout.
Signed-off-by: Shyam Sundar <shyam.sundar@marvell.com>
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The purpose of flush routine is to cleanup I/Os to the firmware and
complete them to scsi middle layer. This routine is invoked before
connection is uploaded because of rport going away.
- Don't process any I/Os, aborts, TMFs coming when flush in progress.
- Add flags to handle cleanup and release of I/Os because flush can
prematurely complete I/Os.
- Original command can get completed to driver when cleanup for same is
posted to firmware, handle this condition.
- Modify flush to handle I/Os in all the states like abort, TMF, RRQ and
timeouts.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When mapping the pages from a scatter/gather list from the SCSI layer we
only need to follow these rules:
- Max SGEs for each I/O request is 256
- No size limit on each SGE
- No need to split OS provided SGEs to 4K before sending to firmware.
- Slow SGE is applicable only when:
- There are > 8 SGEs and any middle SGE is less than a page size (4K)
Make necessary changes so that driver follows these rules. Applicable only
for Write requests (not for Read requests). No need to check SGE address
alignment requirements (first, middle or last) before declaring slow SGE.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is currently an overlap where exchange IDs between what is used for
offloaded commands and by libfc for ELS commands. Correct this so that
exchange ID range is:
Offloaded requests: 0 to 0xfff
libfc requests: 0x1000 to 0xfffe
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No change to functionality. Simply make transport event messages a little
clearer, and rework CRQ format enums such that we have separate enums for
INIT messages and XPORT events.
[mkp: typo]
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Status and error codes are returned in big endian from the VIOS. The values
are translated into a human readable format when logged, but the values are
also logged. This patch byte swaps those values so that they are consistent
between BE and LE platforms.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The VIOS uses the SCSI_ERROR class to report PRLI failures. These errors
are indicated with the combination of a IBMVFC_FC_SCSI_ERROR return status
and 0x8000 error code. Add these codes to cmd_status[] with appropriate
human readable error message.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The text of messages logged with ibmvfc_log_error() always contain the term
"failed". In the case of cancelled commands during EH they are reported
back by the VIOS using error codes. This can be confusing to somebody
looking at these log messages as to whether a command was successfully
cancelled. The following real log message for example it is unclear if the
transaction was actaully cancelled.
<6>sd 0:0:1:1: Cancelling outstanding commands.
<3>sd 0:0:1:1: [sde] Command (28) failed: transaction cancelled (2:6) flags: 0 fcp_rsp: 0, resid=0, scsi_status: 0
Remove prefixing of "failed" to all error logged messages. The
ibmvfc_log_error() function translates the returned error/status codes to a
human readable message already.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when it sees a logical not on the left side of a conditional
statement because it thinks the logical not should be applied to the whole
statement, not just the left side:
drivers/scsi/qla2xxx/qla_nx.c:3703:7: warning: logical not is only
applied to the left hand side of this comparison
[-Wlogical-not-parentheses]
This particular instance was already fixed by commit 0bfe7d3cae ("scsi:
qla2xxx: Simplify conditional check") upstream but it was reintroduced by
commit 3695310e37 ("scsi: qla2xxx: Update flash read/write routine") in
the 5.2/scsi-queue.
Fixes: 3695310e37 ("scsi: qla2xxx: Update flash read/write routine")
Link: https://github.com/ClangBuiltLinux/linux/issues/80
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit a83da8a450 ("scsi: sd: Optimal I/O size should be a multiple
of physical block size") split one conditional into several separate
statements in an effort to provide more accurate warning messages when
a device reports a nonsensical value. However, this reorganization
accidentally dropped the precondition of the reported value being
larger than zero. This lead to a warning getting emitted on devices
that do not report an optimal I/O size at all.
Remain silent if a device does not report an optimal I/O size.
Fixes: a83da8a450 ("scsi: sd: Optimal I/O size should be a multiple of physical block size")
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Reported-by: Hussam Al-Tayeb <ht990332@gmx.com>
Tested-by: Hussam Al-Tayeb <ht990332@gmx.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and
hence needs the disk->private_data pointer. Avoid that that pointer is
cleared before all affected I/O requests have finished. This patch avoids
that the following crash occurs:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
scsi_mq_uninit_cmd+0x1c/0x30
scsi_end_request+0x7c/0x1b8
scsi_io_completion+0x464/0x668
scsi_finish_command+0xbc/0x160
scsi_eh_flush_done_q+0x10c/0x170
sas_scsi_recover_host+0x84c/0xa98 [libsas]
scsi_error_handler+0x140/0x5b0
kthread+0x100/0x12c
ret_from_fork+0x10/0x18
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use dd to test a SCSI device:
1. echo "blocked" >/sys/block/sda/device/state
2. dd if=/dev/sda of=/mnt/t.log bs=1M count=10
3. echo "running" >/sys/block/sda/device/state
dd should finish this work after step 3, but it hangs.
After step2, the call chain is this:
blk_mq_dispatch_rq_list-->scsi_queue_rq-->prep_to_mq
prep_to_mq will return BLK_STS_RESOURCE, and scsi_queue_rq will
transition it to BLK_STS_DEV_RESOURCE which means that driver can
guarantee that IO dispatch will be triggered in future when the
resource is available. Need to follow the rule if we set the device
state to running.
[mkp: tweaked commit description and code comment as suggested by Bart]
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sd_probe() easier to read by inlining sd_probe_part2(). This patch
does not change any functionality.
Cc: Lee Duncan <lduncan@suse.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As explained during the 2018 LSF/MM session about increasing SCSI disk
probing concurrency, the problems with the current probing approach are as
follows:
- The driver core is unaware of asynchronous SCSI LUN probing.
wait_for_device_probe() waits for all asynchronous probes except
asynchronous SCSI disk probes.
- There is unnecessary serialization between sd_probe() and sd_remove().
This can lead to a deadlock.
Hence this patch that modifies the sd driver such that it uses the driver
core framework for asynchronous probing. The async domains and
get_device()/put_device() pairs that became superfluous due to this change
are removed.
This patch does not affect the time needed for loading the scsi_debug
kernel module with parameters delay=0 and max_luns=256.
This patch depends on commit ef0ff68351 ("driver core: Probe devices
asynchronously instead of the driver") that went upstream in kernel version
v5.1-rc1.
Cc: Lee Duncan <lduncan@suse.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a couple of statements that are incorrectly indented, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable len is not being inintialized and the uninitialized value is
being returned. However, this return path is never reached because the
default case in the switch statement returns -ENOSYS. Clean up the code by
replacing the return -ENOSYS with a break for the default case and
returning -ENOSYS at the end of the function. This allows len to be
removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case iscsi_lookup_endpoint fails, the fix returns -EINVAL to avoid NULL
pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/scsi/gdth.c:3662:6: warning: variable 'paddr' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
Don't attempt to call dma_free_coherent when buf is NULL (meaning that
we never called dma_alloc_coherent and initialized paddr), which avoids
this warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/402
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm8001_hwi.c: In function 'mpi_smp_completion':
drivers/scsi/pm8001/pm8001_hwi.c:2901:6: warning:
variable 'param' set but not used [-Wunused-but-set-variable]
drivers/scsi/pm8001/pm8001_hwi.c: In function 'pm8001_bytes_dmaed':
drivers/scsi/pm8001/pm8001_hwi.c:3247:24: warning:
variable 'sas_ha' set but not used [-Wunused-but-set-variable]
They're never used since introduction, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a few windows during AER/EEH when we can access PCIe I/O mapped
registers. This will harden the access to insure we do not allow PCIe
access during errors
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Sagar Biradar <sagar.biradar@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang -Wuninitialized notices that on is_qla40XX we never allocate any DMA
memory in get_fw_boot_info() but attempt to free it anyway:
drivers/scsi/qla4xxx/ql4_os.c:5915:7: error: variable 'buf_dma' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (!(val & 0x07)) {
^~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5985:47: note: uninitialized use occurs here
dma_free_coherent(&ha->pdev->dev, size, buf, buf_dma);
^~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5915:3: note: remove the 'if' if its condition is always true
if (!(val & 0x07)) {
^~~~~~~~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5885:20: note: initialize the variable 'buf_dma' to silence this warning
dma_addr_t buf_dma;
^
= 0
Skip the call to dma_free_coherent() here.
Fixes: 2a991c2159 ("[SCSI] qla4xxx: Boot from SAN support for open-iscsi")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
clang -Wuninitialized incorrectly sees a variable being used without
initialization:
drivers/scsi/lpfc/lpfc_nvme.c:2102:37: error: variable 'localport' is uninitialized when used here
[-Werror,-Wuninitialized]
lport = (struct lpfc_nvme_lport *)localport->private;
^~~~~~~~~
drivers/scsi/lpfc/lpfc_nvme.c:2059:38: note: initialize the variable 'localport' to silence this warning
struct nvme_fc_local_port *localport;
^
= NULL
1 error generated.
This is clearly in dead code, as the condition leading up to it is always
false when CONFIG_NVME_FC is disabled, and the variable is always
initialized when nvme_fc_register_localport() got called successfully.
Change the preprocessor conditional to the equivalent C construct, which
makes the code more readable and gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.
The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building the ufs-mediatek module the following warning shows up:
WARNING: modpost: missing MODULE_LICENSE() in
drivers/scsi/ufs/ufs-mediatek.o
Rework to add MODULE_LICENSE,MODULE_AUTHOR and MODULE_DESCRIPTION.
Fixes: ddd90623ce ("scsi: ufs-mediatek: Add UFS support for Mediatek SoC chips")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During expander reset handling, the driver invokes kernel function
scsi_host_find_tag() to obtain outstanding requests associated with the
scsi host managed by the driver. Driver loops from tag value zero to hba
queue depth to obtain the outstanding scmds. But when blk-mq is enabled,
the block layer may return stale entry for one or more requests. This may
lead to kernel panic if the returned value is inaccessible or the memory
pointed by the returned value is reused.
Reference of upstream discussion:
https://patchwork.kernel.org/patch/10734933/
Instead of calling scsi_host_find_tag() API for each and every smid (smid
is tag +1) from one to shost->can_queue, now driver will call this API (to
obtain the outstanding scmd) only for those smid's which are outstanding at
the driver level.
Driver will determine whether this smid is outstanding at driver level by
looking into it's corresponding MPI request frame, if its MPI request frame
is empty, then it means that this smid is free and does not need to call
scsi_host_find_tag() for it. By doing this, driver will invoke
scsi_host_find_tag() for only those tags which are outstanding at the
driver level.
Driver will check whether particular MPI request frame is empty or not by
looking into the "DevHandle" field. If this field is zero then it means
that this MPI request is empty. For active MPI request DevHandle must be
non-zero.
Also driver will memset the MPI request frame once the corresponding scmd
is processed (i.e. just before calling
scmd->done function).
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The event pool used for queueing commands is destroyed fairly early in the
ibmvscsi_remove() code path. Since, this happens prior to the call so
scsi_remove_host() it is possible for further calls to queuecommand to be
processed which manifest as a panic due to a NULL pointer dereference as
seen here:
PANIC: "Unable to handle kernel paging request for data at address
0x00000000"
Context process backtrace:
DSISR: 0000000042000000 ????Syscall Result: 0000000000000000
4 [c000000002cb3820] memcpy_power7 at c000000000064204
[Link Register] [c000000002cb3820] ibmvscsi_send_srp_event at d000000003ed14a4
5 [c000000002cb3920] ibmvscsi_send_srp_event at d000000003ed14a4 [ibmvscsi] ?(unreliable)
6 [c000000002cb39c0] ibmvscsi_queuecommand at d000000003ed2388 [ibmvscsi]
7 [c000000002cb3a70] scsi_dispatch_cmd at d00000000395c2d8 [scsi_mod]
8 [c000000002cb3af0] scsi_request_fn at d00000000395ef88 [scsi_mod]
9 [c000000002cb3be0] __blk_run_queue at c000000000429860
10 [c000000002cb3c10] blk_delay_work at c00000000042a0ec
11 [c000000002cb3c40] process_one_work at c0000000000dac30
12 [c000000002cb3cd0] worker_thread at c0000000000db110
13 [c000000002cb3d80] kthread at c0000000000e3378
14 [c000000002cb3e30] ret_from_kernel_thread at c00000000000982c
The kernel buffer log is overfilled with this log:
[11261.952732] ibmvscsi: found no event struct in pool!
This patch reorders the operations during host teardown. Start by calling
the SRP transport and Scsi_Host remove functions to flush any outstanding
work and set the host offline. LLDD teardown follows including destruction
of the event pool, freeing the Command Response Queue (CRQ), and unmapping
any persistent buffers. The event pool destruction is protected by the
scsi_host lock, and the pool is purged prior of any requests for which we
never received a response. Finally, move the removal of the scsi host from
our global list to the end so that the host is easily locatable for
debugging purposes during teardown.
Cc: <stable@vger.kernel.org> # v2.6.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For each ibmvscsi host created during a probe or destroyed during a remove
we either add or remove that host to/from the global ibmvscsi_head
list. This runs the risk of concurrent modification.
This patch adds a simple spinlock around the list modification calls to
prevent concurrent updates as is done similarly in the ibmvfc driver and
ipr driver.
Fixes: 32d6e4b6e4 ("scsi: ibmvscsi: add vscsi hosts to global list_head")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/scsi/ufs/ufs-mediatek.c:112:7: warning: variable 'ret' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (on)
^~
drivers/scsi/ufs/ufs-mediatek.c:120:9: note: uninitialized use occurs
here
return ret;
^~~
drivers/scsi/ufs/ufs-mediatek.c:112:3: note: remove the 'if' if its
condition is always true
if (on)
^~~~~~~
drivers/scsi/ufs/ufs-mediatek.c:108:7: warning: variable 'ret' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (!on)
^~~
drivers/scsi/ufs/ufs-mediatek.c:120:9: note: uninitialized use occurs
here
return ret;
^~~
drivers/scsi/ufs/ufs-mediatek.c:108:3: note: remove the 'if' if its
condition is always true
if (!on)
^~~~~~~~
drivers/scsi/ufs/ufs-mediatek.c:96:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
2 warnings generated.
Remove the default case and initialize ret to -EINVAL to properly fix
this warning.
Fixes: ddd90623ce ("scsi: ufs-mediatek: Add UFS support for Mediatek SoC chips")
Link: https://github.com/ClangBuiltLinux/linux/issues/426
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/ufs/ufs-mediatek.c:19:6: warning: symbol 'ufs_mtk_cfg_unipro_cg' was not declared. Should it be static?
drivers/scsi/ufs/ufs-mediatek.c:55:5: warning: symbol 'ufs_mtk_bind_mphy' was not declared. Should it be static?
drivers/scsi/ufs/ufs-mediatek.c:342:27: warning: symbol 'ufs_mtk_of_match' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Declaring interrupt clear routines as inline is bogus as they are used as
an indirect pointer.
Remove the inline references.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
You can't declare a function inline in a header if it doesn't have a body
available to the compiler. So realistically you either don't declare it
inline or you make it a static inline in the header. I think the latter
applies in this case, so this should be the fix
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We found out that for v2 hw, a SATA disk can not be written to after the
system comes up.
In commit ffb1c820b8 ("scsi: hisi_sas: remove the check of sas_dev status
in hisi_sas_I_T_nexus_reset()"), we introduced a path where we may issue an
internal abort for a SATA device, but without following it with a
softreset.
We need to always follow an internal abort with a software reset, as per HW
programming flow, so add this.
Fixes: ffb1c820b8 ("scsi: hisi_sas: remove the check of sas_dev status in hisi_sas_I_T_nexus_reset()")
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix following sparse warning:
drivers/scsi/mvumi.c:1797:48: warning: Using plain integer as NULL pointer
drivers/scsi/mvumi.c:2143:50: warning: Using plain integer as NULL pointer
drivers/scsi/mvumi.c:755:58: warning: Using plain integer as NULL pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/qedi/qedi_fw.c: In function 'qedi_tmf_resp_work':
drivers/scsi/qedi/qedi_fw.c:158:28: warning:
variable 'cls_sess' set but not used [-Wunused-but-set-variable]
drivers/scsi/qedi/qedi_fw.c: In function 'qedi_tmf_work':
drivers/scsi/qedi/qedi_fw.c:1370:28: warning:
variable 'cls_sess' set but not used [-Wunused-but-set-variable]
It's never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed a typo for 'iiDMA' cmd in qla_bsg.c.
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed a minor formatting issue with comment section in qla_bsg.c
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a few statements that are not indented correctly, so fix
these. Also add empty line between variable declaration and first
statements in functions. Also remove whitespace between * and mvi_dev to
clean up a cppcheck warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An if statement is indented correctly and an outb statement has a redundant
empty comment and incorrect indentation. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several lines where the indentation has an extra space, fix this
by removing the spaces.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clean up { brace to fix cppcheck warning. Remove some trailing spaces at
end of a statement. Also clean up an indentation issue.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds UFS support for MediaTek SoC chips.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_get_pwr_dev_param function and ufs_dev_params struct have been
relocated to ufs core. Switch ufs-hisi to the common interface.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_get_pwr_dev_param function and ufs_dev_params struct have been
relocated to ufs core. Switch ufs-qcom to the common interface.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_get_pwr_dev_param defines an interface for power mode management
currently used by both ufs-qcom and ufs-hisi. Move the interface to ufs
core so every driver can take advantage of it.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use HCTX_TYPE_DEFAULT instead of 0 to avoid hardcoding.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use HCTX_TYPE_DEFAULT instead of 0 to avoid hardcoding.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use HCTX_TYPE_DEFAULT instead of 0 to avoid hardcoding.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use HCTX_TYPE_DEFAULT instead of 0 to avoid hardcoding.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
devm_reset_control_get could fail, so the fix checks its return value and
passes the error code upstream in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 7f147f9bfd ("scsi: qla2xxx: Fix N2N target discovery with Local
loop") fixed N2N target discovery for local loop. However, same code is
used for FC-AL discovery as well. Added check to make sure we are bypassing
area and domain check only in N2N topology for target discovery.
Fixes: 7f147f9bfd ("scsi: qla2xxx: Fix N2N target discovery with Local loop")
Cc: stable@vger.kernel.org # 5.0+
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several lines of code where the indentation is at an incorrect
level; fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since scsi_device_quiesce() skips SCSI devices that have another state than
RUNNING, OFFLINE or TRANSPORT_OFFLINE, scsi_device_resume() should not
complain about SCSI devices that have been skipped. Hence this patch. This
patch avoids that the following warning appears during resume:
WARNING: CPU: 3 PID: 1039 at blk_clear_pm_only+0x2a/0x30
CPU: 3 PID: 1039 Comm: kworker/u8:49 Not tainted 5.0.0+ #1
Hardware name: LENOVO 4180F42/4180F42, BIOS 83ET75WW (1.45 ) 05/10/2013
Workqueue: events_unbound async_run_entry_fn
RIP: 0010:blk_clear_pm_only+0x2a/0x30
Call Trace:
? scsi_device_resume+0x28/0x50
? scsi_dev_type_resume+0x2b/0x80
? async_run_entry_fn+0x2c/0xd0
? process_one_work+0x1f0/0x3f0
? worker_thread+0x28/0x3c0
? process_one_work+0x3f0/0x3f0
? kthread+0x10c/0x130
? __kthread_create_on_node+0x150/0x150
? ret_from_fork+0x1f/0x30
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Martin Steigerwald <martin@lichtvoll.de>
Cc: <stable@vger.kernel.org>
Reported-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Tested-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Fixes: 3a0a529971 ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adjust comments accordingly.
Cc: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cmd->rcu is initialized by scsi_initialize_rq(). For passthrough
requests, blk_get_request() calls scsi_initialize_rq(). For filesystem
requests, scsi_init_command() calls scsi_initialize_rq(). Make sure
that destroy_rcu_head() is called for passthrough requests.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This function is only used inside the SCSI midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise driver copyright message to show 2019. Update couple of files
modified by 12.2.0.1 patch set.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the 6072 log message string to print the whole 32 bits of the
extended status.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver had duplicated log message numbers making debug difficult.
Make all messages unique.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the SLI4 queue creation code to use NUMA node based memory
allocation based on the cpu the queues will be related to.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver maintains a sideband structure which has a pointer for
each queue element. However, at 8 bytes per pointer, and up to 4k elements
per queue, and 100s of queues, this can take up a lot of memory.
Convert the driver to using an access routine that calculates the element
address based on its index rather than using the pointer table.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When in trunking mode, the adapter can be placed into diagnostic mode and
each link in the trunk tested via loopback.
Add support to the driver to perform per-link loopback testing when in
trunking mode.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is using uint16_t and is encountering an overflow of the 16bits when
calculating link speed.
Fix by using a u32 type.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If all the trunk links drop and a single link resumes, the link_state is
not properly reported. When trunked, the driver receives two async
cqes. One acqe reports the trunk link states, which the driver records.
The other cqe reports the overall state of the trunk. In the failing case,
the trunk link state acqe preceeds the overall trunk link state acqe. The
trunk link state acqe, as it's an "up" transition, calls a code path which
ensures a down transition before moving to the up state. The down
transition had a side effect of clearing the just-saved trunk link states.
Fix by not clearing the trunk link states if we've already transitioned
to a down state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalid test is allowing Loop to be a supported topology on G6 and G7
adapters. The chips do not support loop as their link speeds prohibit loop
per standard.
Correct the conditional so that loop is not reported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently reporting the firmware revision not the actual boot
bios version in FDMI data.
Modify the driver to obtain the boot bios version from the adapter and use
that data in the FMDI data sent to the switch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switch is rejecting FDMI2 registration for symbolic name. There is a
"\n" in the name string, which the switch dislikes thus rejects the
registration.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is reporting support for NVME even when not configured for NVME
operation.
Fix (and make more readable) when NVME protocol support is indicated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.
Set the value to "Emulex Corporation" for consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the driver undergoes repeated host resets it starts losing exchange
structures and eventually returns SCSI_MLQUEUE_HOST_BUSY and does not
recover. The offline path is not reclaiming the outstanding ios on the fcp
pring txcmplq before calling lpfc_destroy_multixripool, which causes the
txmcplq to be reinit and the resources lost.
Flush the fcp rings before destroying the multixripools.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter initialization sequence enables interrupts, initializes the
adapter link_state to LINK_DOWN, then issues commands to initialize the
adapter. The interrupt handler on the adapter validates the link_state (has
to be at least LINK_DOWN) and if invalid, will discard the interrupting
event.
In most cases, there is not a command completion, thus an interrupt until
the initialization commands have been sent which is post the setting of
state to LINK_DOWN. However, in cases of firmware reset, the reset will
modify the link_state to an invalid value (indicating a reset of the
adapter) and there occasionally are cases where the adapter will generate
an asynchronous event which shares the eq/cq used for mailbox commands. In
the failure case, an interrupt is generated immediately after enabling them
due to the async event. As link_state is invalid, the eq is list and the
CQ not serviced. At this point link_state is initialized and the mailbox
command sent. As the CQ has not been serviced, it is not armed, so no
interrupt event is generated when the mailbox command completes.
Modify the initialization sequence so that interrupts are enabled after
link_state is properly initialized, which avoids the race condition with
the async event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the scsi error handler to fire and call the target reset
handler simultaneously to the driver logging out and relogging into the
system. If hit just right, the re-login may not have fully re-established
the remote port and the rdata->pnod structure may be null.
Check for NULL in the reset handler and return failure if NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code incorrectly specifies a completion wait timeout duration in 5
jiffies, when it should have been 5 seconds.
Fix the adjust for units for the completion timeout call.
[mkp: manual merge]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code is using msleep when polling for hw ready. Unfortunately the
msleep routine isn't very accurate on rescheduling. In fact, on a busy
systems which reset the adapter, it became 10s of seconds before it was
rescheduled.
Fix by busy waiting using udelay. As we're now busy waiting, significantly
reduce the wait time so that we can exit the pool loop as soon as possible.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver periodically checks for adapter error in a background thread. If
the thread detects an error, the adapter will be reset including the
deletion and reallocation of workqueues on the adapter. Simultaneously,
there may be a user-space request to offline the adapter which may try to
do many of the same steps, in parallel, on a different thread. As memory
was deallocated while unexpected, the parallel offline request hit a bad
pointer.
Add coordination between the two threads. The error recovery thread has
precedence. So, when an error is detected, a flag is set on the adapter to
indicate the error thread is terminating the adapter. But, before doing
that work, it will look for a flag that is set by the offline flow, and if
set, will wait for it to complete before then processing the error handling
path. Similarly, in the offline thread, it first checks for whether the
error thread is resetting the adapter, and if so, will then wait for the
error thread to finish. Only after it has finished, will it set its flag
and offline the adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a couple of cases, the driver detected a pci error (via pci device state
or via failed register reads) but didn't take any action to disable the
device. Additionally, the driver is ignoring the status of pci
configuration space reads.
Having the driver take the adapter offline whenever the pci error is
detected. Pay attention to pci_config_space_read status and return failure
if an error is seen.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an adapter fails, causing a board reset, the board reset routine
lpfc_hba_down_s4() takes the hbalock out then calls
lpfc_nvmet_ctxbuf_post() who then tries to take out the same lock. As the
context lists are now protected under the buf_list_locks, there is no need
for the hbalock to be held by the board reset routine.
Fix by no longer taking the hbalock in the board reset routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With negative test injection, the driver is receiving a command with first
burst enabled, meaning Sequence initiative is not passed with the command
frame. The driver notes the condition and discards the frame. However the
driver calls the incorrect buffer free routine, resulting in a NULL pointer
reference.
For hbq buffer free, convert to using lpfc_rq_buf_free().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, when lpfc_nvmet_mrq is 0 it could mean 2 different things
depending on when its looked at. If at module load time it specifies the
default number of hardware queues to allocate, with 0 meaning default to
the number of CPUs. But post module load, a value of zero means to disable
mrq use.
Changed the driver so that enablement of mrq is based on whether nvme
target mode is enabled or not. When enabled, mrq is enabled. Thus, the
cfg_nvemt_mrq field only specifies the number of mrq queues to enable, with
0 defaulting to the number of cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under circustances with high load, the driver is running out of async
receive buffers which may result in one of the following messages:
0:6401 RQE Error x13, posted 226 err_cnt 0: 925c6050 925c604e 925c5d54
or
0:2885 Port Status Event: port status reg 0x81800000,
port smphr reg 0xc000, error 1=0x52004a01, error 2=0x0
The driver is waiting for full io completion before returning receive
buffers to the adapter. There is no need for such a relationship.
Whenever a new command is received from the wire, the driver will have two
contexts - an io context (ctxp) and a receive buffer context. In current
code, the receive buffer context stays 1:1 with the io and won't be
reposted to the hardware until the io completes. There is no need for such
a relationship.
Change the driver so that up on successful handing of the command to the
transport, where the transport has copied what it needed thus the buffer is
returned to the driver, have the driver immediately repost the buffer to
the hardware. If the command cannot be successfully handed to the transport
as transport resources are temporarily busy, have the driver allocate a new
and separate receive buffer and post it to the hardware so that hardware
can continue while the command is queued for the transport.
When an io is complete, the transport returns the io context to the driver,
and the driver may be waiting for more contexts, thus immediately reuse the
io context. In this path, there was a buffer posted when the receive buffer
was queued waiting for an io context so a replacement is not needed in the
new code additions. Thus, exempt this the context reuse case from the
buffer reposting.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The debug ktime counters that trace an io were inadvertently not placed in
the common section of an io buffer. Thus, they generate an invalid opcode
error when accessed.
Move the ktime counters into the common area.
Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed. The problem was reported
by KASAN.
While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary. Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.
Reported by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A patch in the 12.2.0.0 set caused a new lockdep warning:
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
5.0.0-rc8-next-20190301-dbg+ #1 Not tainted
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&qp->io_buf_list_put_lock)->rlock);
local_irq_disable();
lock(&(&phba->hbalock)->rlock);
lock(&(&qp->io_buf_list_put_lock)->rlock);
<Interrupt>
lock(&(&phba->hbalock)->rlock);
see: https://www.spinics.net/lists/linux-scsi/msg128389.html
In summary, the new patch added taking the io_buf_list_put_lock while under
an irq-disabled hbalock. This created a lock heirarchy dependent upon irq
being disabled, and there are paths that take the io_buf_list_put_lock
without disabling irq.
Looking at the lpfc_io_free routine, which is where the new heirarchy was
introduced, there is no reason to be taking out the hbalock and raising
irq, as the functionality is replaced by the io_buf_list_xxx locks.
Resolve by removing the hbalock/irq calls in lpfc_io_free.
Fixes: 5e5b511d8b ("scsi: lpfc: Partition XRI buffer list across Hardware Queues")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior patch which added support for non-uniform allocation of MSIX
vectors now causes a smatch complaint:
drivers/scsi/lpfc/lpfc_scsi.c:3674 lpfc_scsi_cmd_iocb_cmpl()
error: we previously assumed 'phba->sli4_hba.hdwq' could be
null (see line 3667)
Resolve by removing the unnecessary check for a NULL hdwq table.
Fixes 6a828b0f61: ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This version includes support for ISP28XX.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for Secure flash update with ISP28xx.
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Includes the following:
- correction to 27xx image status struct;
- factoring of 27xx image status validating routines to make common;
- image status generation compare that works across zero wrap;
- bsg interface to report current active images (as loaded by driver).
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Mike Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce stack space on each fwdt routine by eliminating local variable reg.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch cleans up and fixes firmware dump template processing. These
changes are added to support newer features for ISP27XX/ISP28XX.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes following changes to flash access routines:
- update return type for read_optrom
- use void instead of uint32_t * for buffer parameter in read
and write optrom routines
- fix flash/nvram addressing
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds multipe firmware dump template and segments support for
ISP27XX/28XX.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does following:
- Clean up NVRAM code.
- Optimizes reading of primary/secondary flash image validation.
- Remove 0xff mask and make correct width in FLT structure.
- Use endian macros to assign static fields in fwdump header.
- Correct fdwt checksum calculation.
- Simplify ql_dump_buffer() interface usage.
- Add endianizers to 27xx firmware image validator.
- fixes compiler warnings for big endian architecture.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes reported speed for min_link and max_supported speed. Also
rename sysfs nodes link_speed and max_supported to be consistent with
{min|max}_suuported_speed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Mike Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds sysfs node for serdes_version and also cleans up port_speed
display.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds PCI device ID ISP28XX for Gen7 support. Also signature
determination for primary/secondary flash image for ISP27XX/28XX is aded as
part of Gen7 support.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes qla27xx_dump_{mpi|ram} api for ISP27XX.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes FW default template as there will never be case where
the default template would be invoked.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds new sysfs node to display firmware attributes and port
number.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated driver version to 28.100.00.00, which is equivalent to OOB Phase 9.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Reduce the threshold value to 1/4 of the queue depth.
* With this FW can find enough entries to post the Reply Descriptors in the
reply descriptor post queue.
* With module param, user can play with threshold value, the same
irqpoll_weight is used as the budget in processing of reply descriptor
post queues in _base_process_reply_queue.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver uses "reply descriptor post queues" in round robin fashion so that
IO's are distributed to all the available reply descriptor post queues
equally. With this each reply descriptor post queue load is balanced.
This is enabled only if CPUs count to MSI-X vector count ratio is X:1
(where X > 1) This improves performance and also fixes soft lockups.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue Description:
We have seen cpu lock up issue from fields if system has greater (more than
96) logical cpu count. SAS3.0 controller (Invader series) supports at max
96 msix vector and SAS3.5 product (Ventura) supports at max 128 msix
vectors.
This may be a generic issue (if PCI device supports completion on multiple
reply queues). Let me explain it w.r.t to mpt3sas supported h/w just to
simplify the problem and possible changes to handle such issues. IT HBA
(mpt3sas) supports multiple reply queues in completion path. Driver creates
MSI-x vectors for controller as "min of (FW supported Reply queue, Logical
CPUs)". If submitter is not interrupted via completion on same CPU, there
is a loop in the IO path. This behavior can cause hard/soft CPU lockups, IO
timeout, system sluggish etc.
Example - one CPU (e.g. CPU A) is busy submitting the IOs and another CPU
(e.g. CPU B) is busy with processing the corresponding IO's reply
descriptors from reply descriptor queue upon receiving the interrupts from
HBA. If the CPU A is continuously pumping the IOs then always CPU B (which
is executing the ISR) will see the valid reply descriptors in the reply
descriptor queue and it will be continuously processing those reply
descriptor in a loop without quitting the ISR handler.
Mpt3sas driver will exit ISR handler if it finds unused reply descriptor in
the reply descriptor queue. Since CPU A will be continuously sending the
IOs, CPU B may always see a valid reply descriptor (posted by HBA Firmware
after processing the IO) in the reply descriptor queue. In worst case,
driver will not quit from this loop in the ISR handler. Eventually, CPU
lockup will be detected by watchdog.
Above mentioned behavior is not common if "rq_affinity" set to 2 or
affinity_hint is honored by irqbalance as "exact". If rq_affinity is set
to 2, submitter will be always interrupted via completion on same CPU. If
irqbalance is using "exact" policy, interrupt will be delivered to
submitter CPU.
If CPU counts to MSI-X vectors (reply descriptor Queues) count ratio is not
1:1, we still have exposure of issue explained above and for that we don't
have any solution.
Exposure of soft/hard lockup if CPU count is more than MSI-x supported by
device.
If CPUs count to MSI-x vectors count ratio is not 1:1, (Other way, if CPU
counts to MSI-x vector count ratio is something like X:1, where X > 1) then
'exact' irqbalance policy OR rq_affinity = 2 won't help to avoid CPU
hard/soft lockups. There won't be any one to one mapping between CPU to
MSI-x vector instead one MSI-x interrupt (or reply descriptor queue) is
shared with group/set of CPUs and there is a possibility of having a loop
in the IO path within that CPU group and may observe lockups.
For example: Consider a system having two NUMA nodes and each node having
four logical CPUs and also consider that number of MSI-x vectors enabled on
the HBA is two, then CPUs count to MSI-x vector count ratio as 4:1. e.g.
MSIx vector 0 is affinity to CPU 0, CPU 1, CPU 2 & CPU 3 of NUMA node 0 and
MSI-x vector 1 is affinity to CPU 4, CPU 5, CPU 6 & CPU 7 of NUMA node 1.
numactl --hardware
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 --> MSI-x 0
node 0 size: 65536 MB
node 0 free: 63176 MB
node 1 cpus: 4 5 6 7 -->MSI-x 1
node 1 size: 65536 MB
node 1 free: 63176 MB
Assume that user started an application which uses all the CPUs of NUMA
node 0 for issuing the IOs. Only one CPU from affinity list (it can be any
cpu since this behavior depends upon irqbalance) CPU0 will receive the
interrupts from MSIx vector 0 for all the IOs. Eventually, CPU 0 IO
submission percentage will be decreasing and ISR processing percentage will
be increasing as it is more busy with processing the interrupts. Gradually
IO submission percentage on CPU 0 will be zero and it's ISR processing
percentage will be 100 percentage as IO loop has already formed within the
NUMA node 0, i.e. CPU 1, CPU 2 & CPU 3 will be continuously busy with
submitting the heavy IOs and only CPU 0 is busy in the ISR path as it
always find the valid reply descriptor in the reply descriptor
queue. Eventually, we will observe the hard lockup here.
Chances of occurring of hard/soft lockups are directly proportional to
value of X. If value of X is high, then chances of observing CPU lockups is
high.
Solution: Use IRQ poll interface defined in " irq_poll.c". mpt3sas driver
will execute ISR routine in Softirq context and it will always quit the
loop based on budget provided in IRQ poll interface.
In these scenarios (i.e. where CPUs count to MSI-X vectors count ratio is
X:1 (where X > 1)), IRQ poll interface will avoid CPU hard lockups due to
voluntary exit from the reply queue processing based on budget. Note -
Only one MSI-x vector is busy doing processing.
Irqstat output:
IRQs / 1 second(s)
IRQ# TOTAL NODE0 NODE1 NODE2 NODE3 NAME
44 122871 122871 0 0 0 IR-PCI-MSI-edge mpt3sas0-msix0
45 0 0 0 0 0 IR-PCI-MSI-edge mpt3sas0-msix1
We use this approach only if cpu count is more than FW supported MSI-x
vector
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Separate out processing of reply descriptor post queue from _base_interrupt
to _base_process_reply_queue.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed typo in request_desript_type.
request_desript_type --> request_descript_type.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Ajish Koshy <ajish.koshy@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are times when a TUR can take longer than the DEFAULT_TIMEOUT
value. The timeout code is not correct as the function exits with an
automatic as the completion variable...To be fixed later.
Remove the TUR timeout.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a 'rare' race condition where a disk is failed after a device list
has been obtained from the controller and before attempting to get the
device id.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Multipath failures are normally detected at the frequency of the event
thread. Detect LUN failures earlier by checking request completion status.
Reviewed-by: Bader Ali-saleh <bader.ali-saleh@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Prasad Munirathnam <Prasad.Munirathnam@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes and performance
improvements to our initial submit. The main regression fix is the
ia64 simscsi build failure which was missed in the serial number
elimination conversion.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIxBayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisherpAP4rxLpX
bcUnQnEsvoxys/JyoK08Qfv1JebZo1B2MAZ62wD/VZ7LpOuzVLhsM2KhLFGRrs1/
7D2K4tgtO2dQsFix7H0=
=pcHl
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
Fix performance issue where the queue depth for SmartIOC logical volumes is
set to 1, and allow the usual logical volume code to be executed
Fixes: a052865fe2 (aacraid: Set correct Queue Depth for HBA1000 RAW disks)
Cc: stable@vger.kernel.org
Signed-off-by: Sagar Biradar <Sagar.Biradar@microchip.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It used to be that "error" was set to -ENODEV at the start of the function
but we shifted some code around an now "error" is set to zero for most
error paths. There is a mix of direct returns and "goto out" but I changed
everything to direct returns for consistency.
Fixes: 56de835704 ("scsi: lpfc: fix calls to dma_set_mask_and_coherent()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
-----BEGIN PGP SIGNATURE-----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=VBaU
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
If there is an error queueing an iscsi command in iscsi_queuecommand(), for
example if the transport fails to take the command in
sessuin->tt->xmit_task(), then the error path can call
iscsi_complete_task() without first aquiring the back_lock as
required. This can lead to things like ITT pool can get corrupt, resulting
in duplicate ITTs being sent out.
The solution is to hold the back_lock around iscsi_complete_task() calls,
and to add a little commenting to help others understand when back_lock
must be held.
Signed-off-by: Lee Duncan <lduncan@suse.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With default value of register SERDES_CFG, the link is not stable for some
special disks when running IO. According to HW guys' suggestion, need to
make the bit10~19 value of register SERDES_CFG the max value to increase
the reliability of the HiLink.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Yupeng Zhou <zhouyupeng1@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we exchange SAS expander from one SAS controller to other SAS controller
without powering it down, the STP target port will maintain previous
affiliation and reject all subsequent connection requests from other STP
initiator ports with OPEN_REJECT (STP RESOURCES BUSY).
To solve this issue, send HARD RESET to clear the previous affiliation of
STP target port according to SPL (chapter 6.19.4).
We (re-)introduce dev status flag to know if to sleep in NEXUS reset code
or not for remote PHYs. The idea is that if the device is being
initialised, we don't require the delay, and caller would wait for link to
be established, cf. sas_ata_hard_reset().
Co-developed-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the PHY comes down, we currently do not set the negotiated linkrate:
root@(none)$ pwd
/sys/class/sas_phy/phy-0:0
root@(none)$ more enable
1
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$
This patch fixes the driver code to set it properly when the PHY comes
down.
If the PHY had been enabled, then set unknown; otherwise, flag as disabled.
The logical place to set the negotiated linkrate for this scenario is PHY
down routine, which is called from the PHY down ISR.
However, it is not possible to know if the PHY comes down due to PHY
disable or loss of link, as sas_phy.enabled member is not set until after
the transport disable routine is complete, which races with the PHY down
ISR.
As an imperfect solution, use sas_phy_data.enable as the flag to know if
the PHY is down due to disable. It's imperfect, as sas_phy_data is internal
to libsas.
I can't see another way without adding a new field to hisi_sas_phy and
managing it, or changing SCSI SAS transport.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The later revision of v3 hw has added an function of interrupt coalesce
according to time for PHY RX errors. We set the coalesce time to 1s. Then
we print PHY RX errors count when PHY RX errors happen, and don't need to
worry that there may be too much log prints.
Besides, we use hisi_sas_phy.lock to protect error count value. Because we
update them by calling phy_get_events_v3_hw(), which is also used by core
driver (for get PHY events function).
We relocate phy_get_events_v3_hw() to avoid a further declaration.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For internal IO and SMP IO, there is a time-out timer for them. In the
timer handler, it checks whether IO is done according to the flag
task->task_state_lock.
There is an issue which may cause system suspended: internal IO or SMP IO
is sent, but at that time because of hardware exception (such as inject
2Bit ECC error), so IO is not completed and also not timeout. But, at that
time, the SAS controller reset occurs to recover system. It will release
the resource and set the status of IO to be SAS_TASK_STATE_DONE, so when IO
timeout, it will never complete the completion of IO and wait for ever.
[ 729.123632] Call trace:
[ 729.126791] [<ffff00000808655c>] __switch_to+0x94/0xa8
[ 729.133106] [<ffff000008d96e98>] __schedule+0x1e8/0x7fc
[ 729.138975] [<ffff000008d974e0>] schedule+0x34/0x8c
[ 729.144401] [<ffff000008d9b000>] schedule_timeout+0x1d8/0x3cc
[ 729.150690] [<ffff000008d98218>] wait_for_common+0xdc/0x1a0
[ 729.157101] [<ffff000008d98304>] wait_for_completion+0x28/0x34
[ 729.165973] [<ffff000000dcefb4>] hisi_sas_internal_task_abort+0x2a0/0x424 [hisi_sas_test_main]
[ 729.176447] [<ffff000000dd18f4>] hisi_sas_abort_task+0x244/0x2d8 [hisi_sas_test_main]
[ 729.185258] [<ffff000008971714>] sas_eh_handle_sas_errors+0x1c8/0x7b8
[ 729.192391] [<ffff000008972774>] sas_scsi_recover_host+0x130/0x398
[ 729.199237] [<ffff00000894d8a8>] scsi_error_handler+0x148/0x5c0
[ 729.206009] [<ffff0000080f4118>] kthread+0x10c/0x138
[ 729.211563] [<ffff0000080855dc>] ret_from_fork+0x10/0x18
To solve the issue, callback function task_done of those IOs need to be
called when on SAS controller reset.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the tool fortify, phy_up_v3_hw() returns signed value, while
it should return an unsigned value.
So change variable "res" from int to irq_return_t.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The error handling was unintentionally left out so it introduces a Smatch
static checker warning:
drivers/scsi/qla2xxx/qla_attr.c:1655 qla2x00_port_speed_store()
error: uninitialized symbol 'type'.
Fixes: a7b9ca7fc87a ("scsi: qla2xxx: Add support for setting port speed")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On 32-bit architectures, we see a warning when %ld is used to print a
size_t:
In file included from drivers/scsi/lpfc/lpfc_init.c:62:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_new_io_buf':
drivers/scsi/lpfc/lpfc_logmsg.h:62:45: error: format '%ld' expects argument of type 'long int', but argument 5 has type 'unsigned int' [-Werror=format=]
This is harmless, but portable code should just use %zd to avoid the
warning.
Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The newly introduced 'cpu' variable is only used inside of an optional
block, so we get a warning without CONFIG_SCSI_LPFC_DEBUG_FS:
drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_nvme_io_cmd_wqe_cmpl':
drivers/scsi/lpfc/lpfc_nvme.c:968:30: error: unused variable 'cpu' [-Werror=unused-variable]
uint32_t code, status, idx, cpu;
Move the declaration into the same block to avoid the warning.
Fixes: 63df6d637e ("scsi: lpfc: Adapt cpucheck debugfs logic to Hardware Queues")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In "XFS over network block device" scenario XFS can create IO requests with
slab-based XFS metadata. During processing such requests tcp_sendpage() can
merge skb fragments with neighbour slab objects.
If receiving side is located on the same host tcp_recvmsg() can trigger
BUG_ON in hardening check and crash the host with following message:
usercopy: kernel memory exposure attempt detected
from XXXXXXXX (kmalloc-512) (1024 bytes)
This patch redirect such requests from sednpage to sendmsg path. The
problem is similar to one described in recent commit 7e241f647d
("libceph: fall back to sendmsg for slab pages")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Depending on the target architecture and configuration, both phys_addr_t
and dma_addr_t may be smaller than 'long long', so we get a warning when
printing either of them using the %llx format string:
drivers/scsi/qla2xxx/qla_iocb.c: In function 'qla24xx_walk_and_build_prot_sglist':
drivers/scsi/qla2xxx/qla_iocb.c:1140:46: error: format '%llx' expects argument of type 'long long unsigned int', but argument 6 has type 'dma_addr_t' {aka 'unsigned int'} [-Werror=format=]
"%s: page boundary crossing (phys=%llx len=%x)\n",
~~~^
%x
__func__, sle_phys, sg->length);
~~~~~~~~
drivers/scsi/qla2xxx/qla_iocb.c:1180:29: error: format '%llx' expects argument of type 'long long unsigned int', but argument 7 has type 'dma_addr_t' {aka 'unsigned int'} [-Werror=format=]
"%s: sg[%x] (phys=%llx sglen=%x) ldma_sg_len: %x dif_bundl_len: %x ldma_needed: %x\n",
~~~^
There are special %pad and %pap format strings in Linux that we could use
here, but since the driver already does 64-bit arithmetic on the values,
using a plain 'u64' seems more consistent here.
Note: A possible related issue may be that the driver possibly checks the
wrong kind of overflow: when an IOMMU is in use, buffers that cross a
32-bit boundary in physical addresses would still be mapped into dma
addresses within the low 4GB space, so I suspect that we actually want to
check sg_dma_address() instead of sg_phys() here.
Fixes: 50b812755e ("scsi: qla2xxx: Fix DMA error when the DIF sg buffer crosses 4GB boundary")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The patch that replaced io channels for hdw_queues now reports the
following static checker warning:
drivers/scsi/lpfc/lpfc_init.c:11136 lpfc_sli4_hba_unset()
error: we previously assumed 'phba->pport' could be null (see line 11074)
Resolve by adding a pport NULL check.
[mkp: tag tweak]
Fixes: cdb42becdd ("scsi: lpfc: Replace io_channels for nvme and fcp with general hdw_queues per cpu"_
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The outer routine lpfc_sli_issue_iocb(), which decomposes into the
SLI3 (s3) or SLI4 (s4) subroutines takes out the locks. For s3, it takes
out the hbalock. For s4, it takes out the ring_lock. The lockdep check in
the s3 and s4 subroutines both check hbalock, which is incorrect for s4.
Revise the s4 subroutine to lockdep check the ring_lock.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without CONFIG_OF, the of_match_node() helper does not evaluate its
argument, and the compiler warns about the unused variable:
drivers/scsi/ufs/ufs-hisi.c: In function 'ufs_hisi_probe':
drivers/scsi/ufs/ufs-hisi.c:673:17: error: unused variable 'dev' [-Werror=unused-variable]
Rework this code to pass the data directly, and while we're at it,
correctly handle the const pointers.
Fixes: 653fcb07d9 ("scsi: ufs: Add HI3670 SoC UFS driver support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When trying to display tgt_counters in the debugfs, a panic can result.
There is no null check for qpair after it is assigned in the for-loop.
Unless vha->hw->queue_pair_map array is completely filled with entries, the
system will panic dereferencing a null pointer.
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megaraid_sas takes 1+ seconds to load while waiting for firmware:
[2.822603] megaraid_sas 0000:03:00.0: Waiting for FW to come to ready state
[3.871003] megaraid_sas 0000:03:00.0: FW now in Ready state
This is due to the following loop in megasas_transition_to_ready(), which
waits a minimum of 1 second, even though the FW becomes ready in tens of
millisecs:
/*
* The cur_state should not last for more than max_wait secs
*/
for (i = 0; i < max_wait; i++) {
...
msleep(1000);
...
dev_info(&instance->pdev->dev, "FW now in Ready state\n");
This is a regression, caused by a change of the msleep granularity from 1
to 1000 due to concern about waiting too long on systems with coarse
jiffies.
To fix, increase iterations and use msleep(20), which results in:
[2.670627] megaraid_sas 0000:03:00.0: Waiting for FW to come to ready state
[2.739386] megaraid_sas 0000:03:00.0: FW now in Ready state
Fixes: fb2f3e96d80f ("scsi: megaraid_sas: Fix msleep granularity")
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they asked
me to do as the MEI driver is starting to interact with the i915 driver,
and it needed some coordination. All of those patches have been
properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+dPQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym1fACgvpZAxjNzoRQJ6f06tc8ujtPk9rUAnR+tCtrZ
9e3l7H76oe33o96Qjhor
=8A2k
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they
asked me to do as the MEI driver is starting to interact with the i915
driver, and it needed some coordination. All of those patches have
been properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time"
* tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (219 commits)
habanalabs: adjust Kconfig to fix build errors
habanalabs: use %px instead of %p in error print
habanalabs: use do_div for 64-bit divisions
intel_th: gth: Fix an off-by-one in output unassigning
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: use NULL to initialize array of pointers
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: soft-reset device if context-switch fails
habanalabs: print pointer using %p
habanalabs: fix memory leak with CBs with unaligned size
habanalabs: return correct error code on MMU mapping failure
habanalabs: add comments in uapi/misc/habanalabs.h
habanalabs: extend QMAN0 job timeout
habanalabs: set DMA0 completion to SOB 1007
habanalabs: fix validation of WREG32 to DMA completion
habanalabs: fix mmu cache registers init
habanalabs: disable CPU access on timeouts
habanalabs: add MMU DRAM default page mapping
habanalabs: Dissociate RAZWI info from event types
misc/habanalabs: adjust Kconfig to fix build errors
...
The virtio scsi spec defines struct virtio_scsi_ctrl_tmf as a set of
device-readable records and a single device-writable response entry:
struct virtio_scsi_ctrl_tmf
{
// Device-readable part
le32 type;
le32 subtype;
u8 lun[8];
le64 id;
// Device-writable part
u8 response;
}
The above should be organised as two descriptor entries (or potentially
more if using VIRTIO_F_ANY_LAYOUT), but without any extra data after "le64
id" or after "u8 response".
The Linux driver doesn't respect that, with virtscsi_abort() and
virtscsi_device_reset() setting cmd->sc before calling virtscsi_tmf(). It
results in the original scsi command payload (or writable buffers) added to
the tmf.
This fixes the problem by leaving cmd->sc zeroed out, which makes
virtscsi_kick_cmd() add the tmf to the control vq without any payload.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the HARDWARE_ERROR/0x3e/0x1 case is triggered, the logical volume
is offlined. When reading the kernel log, the reason why the device
got offlined isn't reported to the user. This situation makes it
difficult for admins to root cause.
Log a message when this condition occurs.
[mkp: tweaked commit message]
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull irq updates from Thomas Gleixner:
"The interrupt departement delivers this time:
- New infrastructure to manage NMIs on platforms which have a sane
NMI delivery, i.e. identifiable NMI vectors instead of a single
lump.
- Simplification of the interrupt affinity management so drivers
don't have to implement ugly loops around the PCI/MSI enablement.
- Speedup for interrupt statistics in /proc/stat
- Provide a function to retrieve the default irq domain
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- The usual small fixes, improvements and cleanups all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
irqchip/imx-irqsteer: Add multi output interrupts support
irqchip/imx-irqsteer: Change to use reg_num instead of irq_group
dt-bindings: irq: imx-irqsteer: Add multi output interrupts support
dt-binding: irq: imx-irqsteer: Use irq number instead of group number
irqchip/brcmstb-l2: Use _irqsave locking variants in non-interrupt code
irqchip/gicv3-its: Use NUMA aware memory allocation for ITS tables
irqdomain: Allow the default irq domain to be retrieved
irqchip/sifive-plic: Implement irq_set_affinity() for SMP host
irqchip/sifive-plic: Differentiate between PLIC handler and context
irqchip/sifive-plic: Add warning in plic_init() if handler already present
irqchip/sifive-plic: Pre-compute context hart base and enable base
PCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
genirq/affinity: Remove the leftovers of the original set support
nvme-pci: Simplify interrupt allocation
genirq/affinity: Add new callback for (re)calculating interrupt sets
genirq/affinity: Store interrupt sets size in struct irq_affinity
genirq/affinity: Code consolidation
irqchip/irq-sifive-plic: Check and continue in case of an invalid cpuid.
irqchip/i8259: Fix shutdown order by moving syscore_ops registration
dt-bindings: interrupt-controller: loongson ls1x intc
...
Nine small fixes. The resume fix is a cosmetic removal of a warning
with an incorrect condition causing it to alarm people wrongly. The
other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit
DMA masks meaning they bounce any page over 4GB before sending it to
the controller. Nowadays, even laptops mostly have memory above 4GB,
so this can lead to significant performance degradation with all the
bouncing.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXHql8CYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQmvAQCSVQRf
kx3ABDGnaj4Km4/Jzibj44aCYwh+ewwtLCWwFQD9GWaEaDxBkbxQDf/YndQKRhYg
VJQjjj6a9VlNSmWoW28=
=L9Fe
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine small fixes.
The resume fix is a cosmetic removal of a warning with an incorrect
condition causing it to alarm people wrongly.
The other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit DMA
masks meaning they bounce any page over 4GB before sending it to the
controller.
Nowadays, even laptops mostly have memory above 4GB, so this can lead
to significant performance degradation with all the bouncing"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Avoid that system resume triggers a kernel warning
scsi: hptiop: fix calls to dma_set_mask()
scsi: hisi_sas: fix calls to dma_set_mask_and_coherent()
scsi: csiostor: fix calls to dma_set_mask_and_coherent()
scsi: bfa: fix calls to dma_set_mask_and_coherent()
scsi: aic94xx: fix calls to dma_set_mask_and_coherent()
scsi: 3w-sas: fix calls to dma_set_mask_and_coherent()
scsi: 3w-9xxx: fix calls to dma_set_mask_and_coherent()
scsi: lpfc: fix calls to dma_set_mask_and_coherent()
T6 adapters generates DDP completion message on receiving all iSCSI pdus in
a sequence. Because of this, driver can not keep track of tcp sequence
number for T6 adapters.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of using viid to get pf number, directly get pf number from
lldi->pf.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We had a test-report where, under memory pressure, adding LUNs to the
systems would fail (the tests add LUNs strictly in sequence):
[ 5525.853432] scsi 0:0:1:1088045124: Direct-Access IBM 2107900 .148 PQ: 0 ANSI: 5
[ 5525.853826] scsi 0:0:1:1088045124: alua: supports implicit TPGS
[ 5525.853830] scsi 0:0:1:1088045124: alua: device naa.6005076303ffd32700000000000044da port group 0 rel port 43
[ 5525.853931] sd 0:0:1:1088045124: Attached scsi generic sg10 type 0
[ 5525.854075] sd 0:0:1:1088045124: [sdk] Disabling DIF Type 1 protection
[ 5525.855495] sd 0:0:1:1088045124: [sdk] 2097152 512-byte logical blocks: (1.07 GB/1.00 GiB)
[ 5525.855606] sd 0:0:1:1088045124: [sdk] Write Protect is off
[ 5525.855609] sd 0:0:1:1088045124: [sdk] Mode Sense: ed 00 00 08
[ 5525.855795] sd 0:0:1:1088045124: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5525.857838] sdk: sdk1
[ 5525.859468] sd 0:0:1:1088045124: [sdk] Attached SCSI disk
[ 5525.865073] sd 0:0:1:1088045124: alua: transition timeout set to 60 seconds
[ 5525.865078] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015070] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015213] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.587439] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
[ 5526.588562] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
Looking at the code of scsi_alloc_sdev(), and all the calling contexts,
there seems to be no reason to use GFP_ATMOIC here. All the different
call-contexts use a mutex at some point, and nothing in between that
requires no sleeping, as far as I could see. Additionally, the code that
later allocates the block queue for the device (scsi_mq_alloc_queue())
already uses GFP_KERNEL.
There are similar allocations in two other functions:
scsi_probe_and_add_lun(), and scsi_add_lun(),; that can also be done with
GFP_KERNEL.
Here is the contexts for the three functions so far:
scsi_alloc_sdev()
scsi_probe_and_add_lun()
scsi_sequential_lun_scan()
__scsi_scan_target()
scsi_scan_target()
mutex_lock()
scsi_scan_channel()
scsi_scan_host_selected()
mutex_lock()
scsi_report_lun_scan()
__scsi_scan_target()
...
__scsi_add_device()
mutex_lock()
__scsi_scan_target()
...
scsi_report_lun_scan()
...
scsi_get_host_dev()
mutex_lock()
scsi_probe_and_add_lun()
...
scsi_add_lun()
scsi_probe_and_add_lun()
...
So replace all these, and give them a bit of a better chance to succeed,
with more chances of reclaim.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warnings by adding the proper missing breaks:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function _base_display_OEMs_branding :
drivers/scsi/mpt3sas/mpt3sas_base.c:3548:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3566:3: note: here
case MPI2_MFGPAGE_DEVID_SAS2308_2:
^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3567:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3601:3: note: here
case MPI25_MFGPAGE_DEVID_SAS3008:
^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3735:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3745:3: note: here
case MPI2_MFGPAGE_DEVID_SAS2308_2:
^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3746:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3768:3: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add missing break statement and fix identation issue.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 9cb62fa24e ("aacraid: Log firmware AIF messages")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No users left, kill it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use request tag instead of the serial number when printing out logging
messages.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the request tag for logging instead of the scsi command serial number.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drop references to scsi_cmnd->serial_number.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Negative constant left-shift is undefined behaviour in the C standard, and
as such newer versions of clang (at least) warn against it. GCC supports it
for a long time, but it would be better to remove it and rely on defined
behaviour.
My understanding is "~(-1 << N)" in 2's complement is intended to generate
a bit pattern of zeroes ending with N '1' bits. The same can be achieved by
"(1 << N) - 1" in a well-defined way, so switch to it to remove the
warning.
Tested: building a kernel with generic SCSI tape, and checking basic
operations (mt status, mt eject) on a real LTO unit. Cannot test the osst
driver.
Signed-off-by: Iustin Pop <iustin@k1024.org>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add this functionality, placing the descriptor being read in the actual
data buffer in the bio.
That is, for both read and write descriptors query upiu, we are using the
job's request_payload. This in turn, is mapped back in user land to the
applicable sg_io_v4 xferp: dout_xferp for write descriptor, and din_xferp
for read descriptor.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow to read descriptors via raw upiu. This in fact was forbidden just as
a precaution, as ufs-bsg actually enforces which functionality is
supported.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we had a write descriptor query upiu, we appended the descriptor right
after the bsg request. This was fine as the bsg driver allows to allocate
whatever buffer we needed in its job request.
Still, the proper way to deliver payload, however small (we only write
config descriptors of 144 bytes), is by using the job request payload data
buffer.
So change this ABI now, while ufs-bsg is still new, and nobody is actually
using it.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFSHC driver defines a few quirks that are not used anywhere:
UFS_DEVICE_QUIRK_BROKEN_LCC
UFS_DEVICE_NO_VCCQ
UFS_DEVICE_QUIRK_NO_LINK_OFF
UFS_DEVICE_NO_FASTAUTO
Let's remove them.
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 60f0187031.
There was one conflict in drivers/scsi/ufs/ufshcd.c
<<<<<<< HEAD
/* Init check for device descriptor sizes */
ufshcd_init_desc_sizes(hba);
ret = ufs_get_device_desc(hba, &card);
if (ret) {
dev_err(hba->dev, "%s: Failed getting device info. err = %d\n",
__func__, ret);
goto out;
}
ufs_fixup_device_setup(hba, &card);
ufshcd_tune_unipro_params(hba);
ret = ufshcd_set_vccq_rail_unused(hba,
(hba->dev_quirks & UFS_DEVICE_NO_VCCQ) ? true : false);
if (ret)
goto out;
=======
ufs_advertise_fixup_device(hba);
>>>>>>> parent of 60f0187031c0... scsi: ufs: disable vccq if it's not needed by UFS device
Resolution: keep HEAD, and delete the ufshcd_set_vccq_rail_unused() call
and corresponding error-handling code.
Clean up loose ends in a follow-up patch.
60f0187031 introduced a small power optimization: ignore the vccq load
specified in the UFSHC DT node when said host controller is connected to
specific Flash chips (currently, Samsung and Hynix).
Unfortunately, this optimization breaks UFS on systems where vccq powers
not only the Flash chip, but the host controller as well, such as APQ8098
MEDIABOX or MTP8998:
[ 3.929877] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11
[ 5.433815] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11
[ 6.937771] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11
[ 6.937866] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr_retry: query attribute, idn 13, failed with error -11 after 3 retires
[ 6.946412] ufshcd-qcom 1da4000.ufshc: ufshcd_disable_auto_bkops: failed to enable exception event -11
[ 6.957972] ufshcd-qcom 1da4000.ufshc: dme-peer-get: attr-id 0x1587 failed 3 retries
[ 6.967181] ufshcd-qcom 1da4000.ufshc: dme-peer-get: attr-id 0x1586 failed 3 retries
[ 6.975025] ufshcd-qcom 1da4000.ufshc: ufshcd_get_max_pwr_mode: invalid max pwm tx gear read = 0
[ 6.982755] ufshcd-qcom 1da4000.ufshc: ufshcd_probe_hba: Failed getting max supported power mode
[ 8.505770] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
[ 10.009807] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
[ 11.513766] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
[ 11.513861] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag_retry: query attribute, opcode 5, idn 3, failed with error -11 after 3 retires
[ 13.049807] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
[ 14.553768] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
[ 16.057767] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
[ 16.057872] ufshcd-qcom 1da4000.ufshc: ufshcd_read_desc_param: Failed reading descriptor. desc_id 8, desc_index 0, param_offset 0, ret -11
[ 16.067109] ufshcd-qcom 1da4000.ufshc: ufshcd_init_icc_levels: Failed reading power descriptor.len = 98 ret = -11
[ 37.073787] ufshcd-qcom 1da4000.ufshc: link startup failed 1
In my opinion, the rationale for the original patch is questionable. If
neither the UFSHC, nor the Flash chip, require any load from vccq, then
that power rail should simply not be specified at all in the DT.
Working around that fact in the driver is detrimental, as evidenced by the
failure to initialize the host controller on MSM8998.
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_device_quiesce() and scsi_device_resume() are called during
system-wide suspend and resume. scsi_device_quiesce() only succeeds for
SCSI devices that are in one of the RUNNING, OFFLINE or TRANSPORT_OFFLINE
states (see also scsi_set_device_state()). This patch avoids that the
following warning is triggered when resuming a system for which quiescing a
SCSI device failed:
WARNING: CPU: 2 PID: 11303 at drivers/scsi/scsi_lib.c:2600 scsi_device_resume+0x4f/0x58
CPU: 2 PID: 11303 Comm: kworker/u8:70 Not tainted 5.0.0-rc1+ #50
Hardware name: LENOVO 80E3/Lancer 5B2, BIOS A2CN45WW(V2.13) 08/04/2016
Workqueue: events_unbound async_run_entry_fn
Call Trace:
scsi_dev_type_resume+0x2e/0x60
async_run_entry_fn+0x32/0xd8
process_one_work+0x1f4/0x420
worker_thread+0x28/0x3c0
kthread+0x118/0x130
ret_from_fork+0x22/0x40
Cc: Przemek Socha <soprwa@gmail.com>
Reported-by: Przemek Socha <soprwa@gmail.com>
Fixes: 3a0a529971 ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'wait_and_poll':
drivers/scsi/megaraid/megaraid_sas_fusion.c:936:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_sync_map_info':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1329:6: warning:
variable 'size_sync_info' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_init_adapter_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1639:39: warning:
variable 'reg_set' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_is_prp_possible':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1925:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_make_prp_nvme':
drivers/scsi/megaraid/megaraid_sas_fusion.c:2047:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_build_ldio_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:2620:42: warning:
variable 'req_desc' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_build_and_issue_cmd_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:3245:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_task_abort_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:4398:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_reset_target_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:4484:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
They're not used anymore and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It was reported that some devices report an OPTIMAL TRANSFER LENGTH of
0xFFFF blocks. That looks bogus, especially for a device with a
4096-byte physical block size.
Ignore OPTIMAL TRANSFER LENGTH if it is not a multiple of the device's
reported physical block size.
To make the sanity checking conditionals more readable--and to
facilitate printing warnings--relocate the checking to a helper
function. No functional change aside from the printks.
Cc: <stable@vger.kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199759
Reported-by: Christoph Anton Mitterer <calestyo@scientia.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask() incorrectly made a second call with the 32
bit DMA mask value when the call with the 64 bit DMA mask value succeeded.
Fixes: 453cd3700c ("scsi: hptiop: use dma_set_mask")
Cc: <stable@vger.kernel.org>
Suggested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA
mask value succeeded.
[mkp: fixed commit message]
Fixes: e4db40e7a1 ("scsi: hisi_sas: use dma_set_mask_and_coherent")
Cc: <stable@vger.kernel.org>
Suggested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
Fixes: c22b332d81 ("scsi: csiostor: switch to generic DMA API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
[mkp: fixed commit message]
Fixes: a69b080025 ("scsi: bfa: use dma_set_mask_and_coherent")
Cc: <stable@vger.kernel.org>
Suggested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
[mkp: fixed subject]
Fixes: 3a21986f1a ("scsi: aic94xx: fully convert to the generic DMA API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
Fixes: b1fa122930 ("scsi: 3w-sas: fully convert to the generic DMA API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
Fixes: b000bced57 ("scsi: 3w-9xxx: fully convert to the generic DMA API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded. This resulted in NVMe/FC connections failing due to
corrupted data buffers, and various other SCSI/FCP I/O errors.
Fixes: f30e1bfd61 ("scsi: lpfc: use dma_set_mask_and_coherent")
Cc: <stable@vger.kernel.org>
Suggested-by: Don Dutile <ddutile@redhat.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Four small fixes: three in drivers and one in the core. The core fix
is also minor in scope since the bug it fixes is only known to affect
systems using SCSI reservations. Of the driver bugs, the libsas one
is the most major because it can lead to multiple disks on the same
expander not being exposed.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXHC4uSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfYwAP9zX676
svxUeEQLLyMLXmGyDZ5um8ne8VDAzXDIrkS06gEAhKju7hb7jYvt0pf3jj+utS+v
KXtT8CpMuj+cffeVXng=
=OkZL
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
commit 1917d42d14 ("fcoe: use enum for fip_mode") introduces a separate
enum for the fip_mode that shall be used during initialisation handling
until it is passed to fcoe_ctrl_link_up to set the initial fip_state. That
change was incomplete and gcc quietly converted in various places between
the fip_mode and the fip_state enum values with implicit enum conversions,
which fortunately cannot cause any issues in the actual code's execution.
clang however warns about these implicit enum conversions in the scsi
drivers. This commit consolidates the use of the two enums, guided by
clang's enum-conversion warnings.
This commit now completes the use of the fip_mode: It expects and uses
fip_mode in {bnx2fc,fcoe}_interface_create and fcoe_ctlr_init, and it calls
fcoe_ctrl_set_set() with the correct values in fcoe_ctlr_link_up(). It
also breaks the association between FIP_MODE_AUTO and FIP_ST_AUTO to
indicate these two enums are distinct.
Link: https://github.com/ClangBuiltLinux/linux/issues/151
Fixes: 1917d42d14 ("fcoe: use enum for fip_mode")
Reported-by: Dmitry Golovin <dima@golovin.in>
Original-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
CC: Lukas Bulwahn <lukas.bulwahn@gmail.com>
CC: Nick Desaulniers <ndesaulniers@google.com>
CC: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when create DMA pool for cmd frames failed, we should return -ENOMEM,
instead of 0.
In some case in:
megasas_init_adapter_fusion()
-->megasas_alloc_cmds()
-->megasas_create_frame_pool
create DMA pool failed,
--> megasas_free_cmds() [1]
-->megasas_alloc_cmds_fusion()
failed, then goto fail_alloc_cmds.
-->megasas_free_cmds() [2]
we will call megasas_free_cmds twice, [1] will kfree cmd_list,
[2] will use cmd_list.it will cause a problem:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
pgd = ffffffc000f70000
[00000000] *pgd=0000001fbf893003, *pud=0000001fbf893003,
*pmd=0000001fbf894003, *pte=006000006d000707
Internal error: Oops: 96000005 [#1] SMP
Modules linked in:
CPU: 18 PID: 1 Comm: swapper/0 Not tainted
task: ffffffdfb9290000 ti: ffffffdfb923c000 task.ti: ffffffdfb923c000
PC is at megasas_free_cmds+0x30/0x70
LR is at megasas_free_cmds+0x24/0x70
...
Call trace:
[<ffffffc0005b779c>] megasas_free_cmds+0x30/0x70
[<ffffffc0005bca74>] megasas_init_adapter_fusion+0x2f4/0x4d8
[<ffffffc0005b926c>] megasas_init_fw+0x2dc/0x760
[<ffffffc0005b9ab0>] megasas_probe_one+0x3c0/0xcd8
[<ffffffc0004a5abc>] local_pci_probe+0x4c/0xb4
[<ffffffc0004a5c40>] pci_device_probe+0x11c/0x14c
[<ffffffc00053a5e4>] driver_probe_device+0x1ec/0x430
[<ffffffc00053a92c>] __driver_attach+0xa8/0xb0
[<ffffffc000538178>] bus_for_each_dev+0x74/0xc8
[<ffffffc000539e88>] driver_attach+0x28/0x34
[<ffffffc000539a18>] bus_add_driver+0x16c/0x248
[<ffffffc00053b234>] driver_register+0x6c/0x138
[<ffffffc0004a5350>] __pci_register_driver+0x5c/0x6c
[<ffffffc000ce3868>] megasas_init+0xc0/0x1a8
[<ffffffc000082a58>] do_one_initcall+0xe8/0x1ec
[<ffffffc000ca7be8>] kernel_init_freeable+0x1c8/0x284
[<ffffffc0008d90b8>] kernel_init+0x1c/0xe4
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds new firmware dump template entries for ISP27XX firmware
dump.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes following checkpatch ERROR
ERROR: space prohibited before that ',' (ctx:WxW)
No change is functionality due to this patch.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code hard codes marker request to use request and response queue
0. This patch make use of the qpair as the path to access the
request/response queues. It allows marker to be place on any hardware
queue.
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent user from sending commands through sysfs while FW is not running or
reset is in progress.
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds sysfs node
1. There is a new sysfs node port_speed
2. The possible values are 2(Auto neg), 8, 16, 32
3. A value outside of the above defaults to Auto neg
4. Any update to the setting causes a link toggle
5. This feature is currently only for ISP27xx
Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com>
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add check to allow 1 discovery command per session to be sent.
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For FC-NVMe, if the fw_started flag is not set or fcport is deleted, then
do not send Abort command
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes driver unload issue when FC-NVMe devices are configured.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add Support for First Burst for FC-NVMe protocol. This feature requires
First Burst support in the firmware.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes LUN discovery when loop ID is not yet assigned by the
firmware during driver load/sg_reset operations. Driver will now search for
new loop id before retrying login.
Fixes: 48acad0990 ("scsi: qla2xxx: Fix N2N link re-connect")
Cc: stable@vger.kernel.org #4.19
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The null check on pointer sess and the subsequent call is redundant as sess
is null on all the the paths that lead to the out_term2 label. Hence the
null check and the call can be removed. Also remove the redundant setting
of sess to NULL as this is not required now.
Detected by CoverityScan, CID#1420663 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sending an srb with qla2x00_start_sp, the sp can complete and be freed
by the time we log the debug message saying we sent it. This can cause a
panic if sp gets reused quickly or when running a kernel that poisons freed
memory.
This was partially fixed by (not every case was addressed):
Commit 9fe278f44b ("scsi: qla2xxx: Move log messages before issuing
command to firmware")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_cpu_affinity_check':
drivers/scsi/lpfc/lpfc_init.c:10599:19: warning:
variable 'phys_id' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit 6a828b0f61 ("scsi: lpfc:
Support non-uniform allocation of MSIX vectors to hardware queues")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add HI3670 SoC UFS driver support by extending the common ufs-hisi
driver. One major difference between HI3660 ad HI3670 SoCs interms of UFS
is the PHY. HI3670 has a 10nm variant PHY and hence this parameter is used
to distinguish the configuration.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Wei Li <liwei213@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The interrupt affinity spreading mechanism supports to spread out
affinities for one or more interrupt sets. A interrupt set contains one or
more interrupts. Each set is mapped to a specific functionality of a
device, e.g. general I/O queues and read I/O queus of multiqueue block
devices.
The number of interrupts per set is defined by the driver. It depends on
the total number of available interrupts for the device, which is
determined by the PCI capabilites and the availability of underlying CPU
resources, and the number of queues which the device provides and the
driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via a
pointer to struct irq_affinity.
Right now the allocation mechanism is complex as it requires to have a loop
in the driver to determine the maximum number of interrupts which are
provided by the PCI capabilities and the underlying CPU resources. This
loop would have to be replicated in every driver which wants to utilize
this mechanism. That's unwanted code duplication and error prone.
In order to move this into generic facilities it is required to have a
mechanism, which allows the recalculation of the interrupt sets and their
size, in the core code. As the core code does not have any knowledge about the
underlying device, a driver specific callback is required in struct
irq_affinity, which can be invoked by the core code. The callback gets the
number of available interupts as an argument, so the driver can calculate the
corresponding number and size of interrupt sets.
At the moment the struct irq_affinity pointer which is handed in from the
driver and passed through to several core functions is marked 'const', but for
the callback to be able to modify the data in the struct it's required to
remove the 'const' qualifier.
Add the optional callback to struct irq_affinity, which allows drivers to
recalculate the number and size of interrupt sets and remove the 'const'
qualifier.
For simple invocations, which do not supply a callback, a default callback
is installed, which just sets nr_sets to 1 and transfers the number of
spreadable vectors to the set_size array at index 0.
This is for now guarded by a check for nr_sets != 0 to keep the NVME driver
working until it is converted to the callback mechanism.
To make sure that the driver configuration is correct under all circumstances
the callback is invoked even when there are no interrupts for queues left,
i.e. the pre/post requirements already exhaust the numner of available
interrupts.
At the PCI layer irq_create_affinity_masks() has to be invoked even for the
case where the legacy interrupt is used. That ensures that the callback is
invoked and the device driver can adjust to that situation.
[ tglx: Fixed the simple case (no sets required). Moved the sanity check
for nr_sets after the invocation of the callback so it catches
broken drivers. Fixed the kernel doc comments for struct
irq_affinity and de-'This patch'-ed the changelog ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-nvme@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Link: https://lkml.kernel.org/r/20190216172228.512444498@linutronix.de
Up to 4.12, __scsi_error_from_host_byte() would reset the host byte to
DID_OK for various cases including DID_NEXUS_FAILURE. Commit
2a842acab1 ("block: introduce new block status code type") replaced this
function with scsi_result_to_blk_status() and removed the host-byte
resetting code for the DID_NEXUS_FAILURE case. As the line
set_host_byte(cmd, DID_OK) was preserved for the other cases, I suppose
this was an editing mistake.
The fact that the host byte remains set after 4.13 is causing problems with
the sg_persist tool, which now returns success rather then exit status 24
when a RESERVATION CONFLICT error is encountered.
Fixes: 2a842acab1 "block: introduce new block status code type"
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function sd_zbc_do_report_zones() issues a REPORT ZONES command with a
buffer size calculated based on the number of zones requested by the
caller. This value should however not exceed the capabilities of the
hardware maximum command size, that is, should not exceed the
max_hw_sectors limit of the device. This problem leads to failures of
report zones commands when re-validating disks with some SAS HBAs.
Fix this by limiting a report zone command buffer size to the minimum of
the device max_hw_sectors and calculated value based on the requested
number of zones. This does not change the semantic of the report_zones file
operation as report zones can always return less zone reports than
requested. Short reports are handled using a loop execution of the
report_zones file operation in the function blk_report_zones().
[Damien]
Before patch 'e76239a3748c ("block: add a report_zones method")', report
zones buffer allocation was limited to max_sectors when allocated in
blk_report_zones(). This however does not consider the actual format of the
device reply which is interface dependent. Limiting the allocation based
on the size of the expected reply format rather than the size of the array
of generic sturct blkzone passed by blk_report_zones() makes more sense.
Fixes: e76239a374 ("block: add a report_zones method")
Cc: stable@vger.kernel.org
Signed-off-by: Masato Suzuki <masato.suzuki@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Two fairly small fixes: the qla one is a panic inducing use after free
and the entropy fix may seem minor but it has had huge userspace
impact thanks to an unrelated change in openssl that causes sshd to
refuse logins until it has enough entropy for the session keys, which
causes tens of minutes delay before the affected systems allow logins
after reboot.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXGb2iiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfPmAQD/eR6G
RkGbnLfXMcP5EfAnEJAYoD8SJsR7UAAV7tdaWwEAihagqOiFmzbDKlceahaZFl27
mizmOjw4EnpIDG2W3Qw=
=BGnV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fairly small fixes: the qla one is a panic inducing use after free
and the entropy fix may seem minor but it has had huge userspace
impact thanks to an unrelated change in openssl that causes sshd to
refuse logins until it has enough entropy for the session keys, which
causes tens of minutes delay before the affected systems allow logins
after reboot"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix panic from use after free in qla2x00_async_tm_cmd
scsi: sd: fix entropy gathering for most rotational disks
-----BEGIN PGP SIGNATURE-----
iQFRBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxgqNUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGwsoH+OVXu0NQofwTvVru
8lgF3BSDG2mhf7mxbBBlBizGVy9jnjRNGCFMC+Jq8IwiFLwprja/G27kaDTkpuF1
PHC3yfjKvjTeUP5aNdHlmxv6j1sSJfZl0y46DQal4UeTG/Giq8TFTi+Tbz7Wb/WV
yCx4Lr8okAwTuNhnL8ojUCVIpd3c8QsyR9v6nEQ14Mj+MvEbokyTkMJV0bzOrM38
JOB+/X1XY4JPZ6o3MoXrBca3bxbAJzMneq+9CWw1U5eiIG3msg4a+Ua3++RQMDNr
8BP0yCZ6wo32S8uu0PI6HrZaBnLYi5g9Wh7Q7yc0mn1Uh1zWFykA6TtqK90agJeR
A6Ktjw==
=scY4
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rc6' into for-5.1/block
Pull in 5.0-rc6 to avoid a dumb merge conflict with fs/iomap.c.
This is needed since io_uring is now based on the block branch,
to avoid a conflict between the multi-page bvecs and the bits
of io_uring that touch the core block parts.
* tag 'v5.0-rc6': (525 commits)
Linux 5.0-rc6
x86/mm: Make set_pmd_at() paravirt aware
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
MAINTAINERS: unify reference to xen-devel list
x86/mm/cpa: Fix set_mce_nospec()
futex: Handle early deadlock return correctly
futex: Fix barrier comment
net: dsa: b53: Fix for failure when irq is not defined in dt
blktrace: Show requests without sector
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
signal: Better detection of synchronous signals
...
QUEUE_FLAG_NO_SG_MERGE has been killed, so kill BLK_MQ_F_SG_MERGE too.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are a handful of statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
As prom_name is not used for anything else, remove it.
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit b2bff6ceb6 ("[SCSI] sd: Quiesce mode sense error messages")
added the macro sd_first_printk(). The macro takes "sdsk" as argument
but dereferences "sdkp". This hasn't caused any real issues since all
callers of sd_first_printk() have an sdkp. But fix the typo.
[mkp: Turned this into a real patch and tweaked commit description]
Signed-off-by: Dietmar Hahn <dietmar.hahn@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In qla2x00_async_tm_cmd, we reference off sp after it has been freed. This
caused a panic on a system running a slub debug kernel. Since fcport is
passed in anyways, just use that instead.
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Giridhar Malavali <gmalavali@marvell.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add padding to make the structure variables in MR_HOST_DEVICE_LIST_ENTRY
64-bit aligned. Also, add reserved fields to MR_HOST_DEVICE_LIST for
future firmware usage.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The problem is that the default for MQ is not to gather entropy, whereas
the default for the legacy queue was always to gather it. The original
attempt to fix entropy gathering for rotational disks under MQ added an
else branch in sd_read_block_characteristics(). Unfortunately, the entire
check isn't reached if the device has no characteristics VPD page. Since
this page was only introduced in SBC-3 and its optional anyway, most less
expensive rotational disks don't have one, meaning they all stopped
gathering entropy when we made MQ the default. In a wholly unrelated
change, openssl and openssh won't function until the random number
generator is initialised, meaning lots of people have been seeing large
delays before they could log into systems with default MQ kernels due to
this lack of entropy, because it now can take tens of minutes to initialise
the kernel random number generator.
The fix is to set the non-rotational and add-randomness flags
unconditionally early on in the disk initialization path, so they can be
reset only if the device actually reports being non-rotational via the VPD
page.
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Fixes: 83e32a5910 ("scsi: sd: Contribute to randomness when running rotational device")
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Xuewei Zhang <xueweiz@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This should return -ENOMEM if kcalloc() fails, but it accidentally
returns success instead.
Fixes: 6a828b0f61 ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Teach scsi_debug to honor SWP in the Control Mode Page and report the
resulting WP state in the Device-Specific Parameter field.
In check_device_access_params() verify that commands that will write
the medium are permitted to do so.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
This patch does not change any functionality but reduces the size of
struct scsi_cmnd.
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit 26e85fcd15 ("[SCSI] sd: Permit merged discard requests";
kernel v3.10) sd_done() sets the residual not only for failed special
requests but also for special requests that succeeded. Hence remove the
code from functions called by sd_init_command() that sets the residual.
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Cc: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent commit removed an element from opcode_info_arr[] but did not
modify opcode_ind_arr[] nor was SDEB_I_XDWRITEREAD removed. Remove
SDEB_I_XDWRITEREAD and bring the two arrays again in sync. This patch
avoids that the following is reported:
BUG: KASAN: null-ptr-deref in scsi_debug_queuecommand+0x60f/0xc90 [scsi_debug]
Read of size 1 at addr 0000000000000001 by task iscsi-test-cu/683
CPU: 3 PID: 683 Comm: iscsi-test-cu Not tainted 5.0.0-rc5-dbg+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
dump_stack+0x86/0xca
kasan_report.cold.3+0x5/0x3e
__asan_load1+0x47/0x50
scsi_debug_queuecommand+0x60f/0xc90 [scsi_debug]
scsi_queue_rq+0xc17/0x12e0
blk_mq_dispatch_rq_list+0x5fc/0xb10
blk_mq_sched_dispatch_requests+0x2f7/0x300
__blk_mq_run_hw_queue+0xd6/0x180
__blk_mq_delay_run_hw_queue+0x25c/0x290
blk_mq_run_hw_queue+0x119/0x1b0
blk_mq_sched_insert_request+0x274/0x350
blk_execute_rq_nowait+0x78/0x90
blk_execute_rq+0xcc/0x140
sg_io+0x30f/0x700
scsi_cmd_ioctl+0x4d4/0x540
scsi_cmd_blk_ioctl+0x7b/0x8b
sd_ioctl+0xba/0x150
blkdev_ioctl+0x6e1/0xea0
block_ioctl+0x79/0x90
do_vfs_ioctl+0x12b/0x9b0
ksys_ioctl+0x41/0x80
__x64_sys_ioctl+0x43/0x50
do_syscall_64+0x71/0x210
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Cc: Christoph Hellwig <hch@lst.de>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Fixes: ae3d56d815 ("scsi: remove bidirectional command support")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a set of five minor fixes (although, tecnhincally, the aicxxx
fix is for a major problem in that the driver won't load without it,
but I think the fact it's taken us since 4.10 to discover this
indicates that the user base for these things has declined).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXF3VNSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUz2AP9L+n9A
Ma5WutU8gkoNcttX7RJvRmtha9RiwvxRi7cs6QD+OToBDpTbo+kLuzfXz0Gop4Go
qQziEsBm1P9ShCti3K0=
=hptI
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of five minor fixes (although, tecnhincally, the aicxxx
fix is for a major problem in that the driver won't load without it,
but I think the fact it's taken us since 4.10 to discover this
indicates that the user base for these things has declined)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxlflash: Prevent deadlock when adapter probe fails
Revert "scsi: libfc: Add WARN_ON() when deleting rports"
scsi: sd_zbc: Fix zone information messages
scsi: target: make the pi_prot_format ConfigFS path readable
scsi: aic94xx: fix module loading
Do some very minor tidy-up, for things like needlessly initing variable and
not leaving whitespace before quote endings.
Originally-from: Xiang Chen <chenxiang66@hisilicon.com>
Originally-from: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For auto-control irq affinity mode, choose the dq to deliver IO according
to the current CPU.
Then it decreases the performance regression that fio and CQ interrupts are
processed on different node.
For user control irq affinity mode, keep it as before.
To realize it, also need to distinguish the usage of dq lock and sas_dev
lock.
We mark as experimental due to ongoing discussion on managed MSI IRQ
during hotplug:
https://marc.info/?l=linux-scsi&m=154876335707751&w=2
We're almost at the point where we can expose multiple queues to the upper
layer for SCSI MQ, but we need to sort out the per-HBA tags performance
issue.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To support queue mapped to a CPU, it needs to be ensured that issuing an
internal abort is safe, in that it is guaranteed that an internal abort is
processed for a single IO or a device after all the relevant command(s)
which it is attempting to abort have been processed by the controller.
Currently we only deliver commands for any device on a single queue to
solve this problem, as we know that commands issued on the same queue will
be processed in order, and we will not have a scenario where the internal
abort is racing against a command(s) which it is trying to abort.
To enqueue commands on queue mapped to a CPU, choosing a queue for an
command is based on the associated queue for the current CPU, so this is
not safe for internal abort since it would definitely not be guaranteed
that commands for the command devices are issued on the same queue.
To solve this issue, we take a bludgeoning approach, and issue a separate
internal abort on any queue(s) relevant to the command or device, in that
we will be guaranteed that at least one of these internal aborts will be
received last in the controller.
So, for aborting a single command, we can just force the internal abort to
be issued on the same queue as the command which we are trying to abort.
For aborting all commands associated with a device, we issue a separate
internal abort on all relevant queues. Issuing multiple internal aborts in
this fashion would have not side affect.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If sending IOs to many disks from single queue, it is possible that the
queue may be full. To avoid the situation, change queue depth from 512 to
4096 which is the max number of IOs for v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add an interface to manually trigger a debugfs dump.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for DIX to v3 hw driver.
For this, we build upon support for DIF, most significantly is adding new
DMA map and unmap paths.
Some pre-existing macro precedence issues are also tidied. They were
detected by checkpatch --strict.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns several times in the scsi subsystem (trimmed for brevity):
drivers/scsi/hpsa.c:6209:7: warning: overflow converting case value to
switch condition type (2147762695 to 18446744071562347015) [-Wswitch]
case CCISS_GETBUSTYPES:
^
drivers/scsi/hpsa.c:6208:7: warning: overflow converting case value to
switch condition type (2147762694 to 18446744071562347014) [-Wswitch]
case CCISS_GETHEARTBEAT:
^
The root cause is that the _IOC macro can generate really large numbers,
which don't fit into type 'int', which is used for the cmd parameter in
the ioctls in scsi_host_template. My research into how GCC and Clang are
handling this at a low level didn't prove fruitful. However, looking at
the rest of the kernel tree, all ioctls use an 'unsigned int' for the
cmd parameter, which will fit all of the _IOC values in the scsi/ata
subsystems.
Make that change because none of the ioctls expect a negative value for
any command, it brings the ioctls inline with the reset of the kernel,
and it removes ambiguity, which is never good when dealing with compilers.
Link: https://github.com/ClangBuiltLinux/linux/issues/85
Link: https://github.com/ClangBuiltLinux/linux/issues/154
Link: https://github.com/ClangBuiltLinux/linux/issues/157
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For files modified as part of 12.2.0.0 patches, update copyright to 2019
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various null pointer dereference and general protection fault panics occur
when there is a link bounce under load. There are a large number of "error"
message 6413 indicating "bad release".
The issues resolve to list corruptions due to missing or inconsistent lock
protection. Lockups are due to nested locks in the unsolicited abort
path. The unsolicited abort path calls the wrong abort processing
routine. There was also duplicate context release while aborts were still
active in the hardware.
Removed duplicate locks and added lock protection around list item
removal. Commonized lock handling around the abort processing routines.
Prevent context release while still in ABTS list.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the transport calls into the lpfc target to release an IO job
structure, which corresponds to an exchange, and if the driver was waiting
for an exchange in order to post a previously received command to the
transport, the driver immediately takes the IO job and reuses the context
for the prior command and calls nvmet_fc_rcv_fcp_req() to tell the
transport about a newly received command.
Problem is, the execution of the IO job release may be in the context of
the back end driver and its bio completion handlers, thus it may be in a
irq context and protection code kicks in in the bio and request layers that
are subsequently called.
Rework lpfc so that instead of immediately upcalling, queue it to a
deferred work thread and have the thread make the upcall.
Took advantage of this change to remove duplicated code with the normal
command receive path that preps the IO job and upcalls nvmet_fc. Created a
common routine both paths use.
Also corrected some errors that were found during review of the context
freeing and reuse - basically unlocked operations and a somewhat disjoint
set of calls to release associated job elements. Cleaned up this path and
added locks for coherency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The conversion to enable SCSI and NVME fc4 support ran into an issue with
NPIV support. With NVME, NPIV is not currently supported, but with SCSI it
was. The driver reverted to its lowest setting meaning NPIV with SCSI was
not allowed.
Convert the NPIV checks and implementation so that SCSI can continue to
allow NPIV support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A scsi host lock is taken on every io completion to check whether the abort
handler is waiting on the io completion. This is an expensive lock to take
on all completion when rarely in an abort condition.
Replace scsi host lock with command-specific lock. Synchronize completion
and abort paths by new cmd lock. Ensure all flag changing and nulling of
context pointers taken under lock. When adding lock to task management
abort, realized it was missing other synchronization locks. Added that
synchronization to match normal paths.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that performance mods don't split resources by protocol and enable both
protocols by default, there's no reason not to enable concurrent SCSI and
NVME fc4 support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The work done to date utilized the number of present cpus when sizing
per-cpu structures. Structures should have been sized based on the max
possible cpu count.
Convert the driver over to possible cpu count for sizing allocation.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current driver uses the older IRQ API for MSIX allocation
Change driver to utilize pci_alloc_irq_vectors when allocating IRQ vectors.
Make lpfc_cpu_affinity_check use pci_irq_get_affinity to determine how the
kernel mapped all the IRQs.
Remove msix_entries from SLI4 structure, replaced with pci_irq_vector()
usage.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driving high iop counts, auto_imax coalescing kicks in and drives the
performance to extremely small iops levels.
There are two issues:
1) auto_imax is enabled by default. The auto algorithm, when iops gets
high, divides the iops by the hdwq count and uses that value to
calculate EQ_Delay. The EQ_Delay is set uniformly on all EQs whether
they have load or not. The EQ_delay is only manipulated every 5s (a
long time). Thus there were large 5s swings of no interrupt delay
followed by large/maximum delay, before repeating.
2) When processing a CQ, the driver got mixed up on the rate of when
to ring the doorbell to keep the chip appraised of the eqe or cqe
consumption as well as how how long to sit in the thread and
process queue entries. Currently, the driver capped its work at
64 entries (very small) and exited/rearmed the CQ. Thus, on heavy
loads, additional overheads were taken to exit and re-enter the
interrupt handler. Worse, if in the large/maximum coalescing
windows,k it could be a while before getting back to servicing.
The issues are corrected by the following:
- A change in defaults. Auto_imax is turned OFF and fcp_imax is set
to 0. Thus all interrupts are immediate.
- Cleanup of field names and their meanings. Existing names were
non-intuitive or used for duplicate things.
- Added max_proc_limit field, to control the length of time the
handlers would service completions.
- Reworked EQ handling:
Added common routine that walks eq, applying notify interval and max
processing limits. Use queue_claimed to claim ownership of the queue
while processing. Always rearm the queue whenever the common routine
is called.
Rework queue element processing, namely to eliminate hba_index vs
host_index. Only one index is necessary. The queue entry can be
marked invalid and the host_index updated immediately after eqe
processing.
After rework, xx_release routines are now DB write functions. Renamed
the routines as such.
Moved lpfc_sli4_eq_flush(), which does similar action, to same area.
Replaced the 2 individual loops that walk an eq with a call to the
common routine.
Slightly revised lpfc_sli4_hba_handle_eqe() calling syntax.
Added per-cpu counters to detect interrupt rates and scale
interrupt coalescing values.
- Reworked CQ handling:
Added common routine that walks cq, applying notify interval and max
processing limits. Use queue_claimed to claim ownership of the queue
while processing. Always rearm the queue whenever the common routine
is called.
Rework queue element processing, namely to eliminate hba_index vs
host_index. Only one index is necessary. The queue entry can be
marked invalid and the host_index updated immediately after cqe
processing.
After rework, xx_release routines are now DB write functions. Renamed
the routines as such.
Replaced the 3 individual loops that walk a cq with a call to the
common routine.
Redefined lpfc_sli4_sp_handle_mcqe() to commong handler definition with
queue reference. Add increment for mbox completion to handler.
- Added a new module/sysfs attribute: lpfc_cq_max_proc_limit To allow
dynamic changing of the CQ max_proc_limit value being used.
Although this leaves an EQ as an immediate interrupt, that interrupt will
only occur if a CQ bound to it is in an armed state and has cqe's to
process. By staying in the cq processing routine longer, high loads will
avoid generating more interrupts as they will only rearm as the processing
thread exits. The immediately interrupt is also beneficial to idle or
lower-processing CQ's as they get serviced immediately without being
penalized by sharing an EQ with a more loaded CQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Review of the eq coalescing logic showed the code was a bit fragmented.
Sometimes it would save/set via an interrupt max value, while in others it
would do so via a usdelay. There were also two places changing eq delay,
one place that issued mailbox commands, and another that changed via
register writes if supported.
Clean this up by:
- Standardizing the operation of lpfc_modify_hba_eq_delay() routine so
that it is always told of a us delay to impose. The routine then chooses
the best way to set that - via register or via mbx.
- Rather than two value types stored in eq->q_mode (usdelay if change via
register, imax if change via mbox) - q_mode always contains usdelay.
Before any value change, old vs new value is compared and only if
different is a change done.
- Revised the dmult calculation. dmult is not set based on overall imax
divided by hardware queues - instead imax applies to a single cpu and
the value will be replicated to all cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
So far MSIX vector allocation assumed it would be 1:1 with hardware
queues. However, there are several reasons why fewer MSIX vectors may be
allocated than hardware queues such as the platform being out of vectors or
adapter limits being less than cpu count.
This patch reworks the MSIX/EQ relationships with the per-cpu hardware
queues so they can function independently. MSIX vectors will be equitably
split been cpu sockets/cores and then the per-cpu hardware queues will be
mapped to the vectors most efficient for them.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The desired affinity for the hardware queue behavior is for hdwq 0 to be
affinitized with cpu 0, hdwq 1 to cpu 1, and so on. The implementation so
far does not do this if the number of cpus is greater than the number of
hardware queues (e.g. hardware queue allocation was administratively
reduced or hardware queue resources could not scale to the cpu count).
Correct the queue affinitization logic when queue count is less than
cpu count.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Default behavior is to use the information from the upper IO stacks to
select the hardware queue to use for IO submission. Which typically has
good cpu affinity.
However, the driver, when used on some variants of the upstream kernel, has
found queuing information to be suboptimal for FCP or IO completion locked
on particular cpus.
For command submission situations, the lpfc_fcp_io_sched module parameter
can be set to specify a hardware queue selection policy that overrides the
os stack information.
For IO completion situations, rather than queing cq processing based on the
cpu servicing the interrupting event, schedule the cq processing on the cpu
associated with the hardware queue's cq.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The XRI get/put lists were partitioned per hardware queue. However, the
adapter rarely had sufficient resources to give a large number of resources
per queue. As such, it became common for a cpu to encounter a lack of XRI
resource and request the upper io stack to retry after returning a BUSY
condition. This occurred even though other cpus were idle and not using
their resources.
Create as efficient a scheme as possible to move resources to the cpus that
need them. Each cpu maintains a small private pool which it allocates from
for io. There is a watermark that the cpu attempts to keep in the private
pool. The private pool, when empty, pulls from a global pool from the
cpu. When the cpu's global pool is empty it will pull from other cpu's
global pool. As there many cpu global pools (1 per cpu or hardware queue
count) and as each cpu selects what cpu to pull from at different rates and
at different times, it creates a radomizing effect that minimizes the
number of cpu's that will contend with each other when the steal XRI's from
another cpu's global pool.
On io completion, a cpu will push the XRI back on to its private pool. A
watermark level is maintained for the private pool such that when it is
exceeded it will move XRI's to the CPU global pool so that other cpu's may
allocate them.
On NVME, as heartbeat commands are critical to get placed on the wire, a
single expedite pool is maintained. When a heartbeat is to be sent, it will
allocate an XRI from the expedite pool rather than the normal cpu
private/global pools. On any io completion, if a reduction in the expedite
pools is seen, it will be replenished before the XRI is placed on the cpu
private pool.
Statistics are added to aid understanding the XRI levels on each cpu and
their behaviors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that the lower half has much better per-cpu parallelization using the
hardware queues, the SCSI MQ support needs to be tied into it.
The involves the following mods:
- Use the hardware queue info from the midlayer to help select the
hardware queue to utilize. This required change to the get_scsi-buf_xxx
routines.
- Remove lpfc_sli4_scmd_to_wqidx_distr() routine. No longer needed.
- Includes fix for SLI-3 that does not have multi queue parallelization.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SLI4 nvme functions are passing the SLI3 ring number when posting wqe to
hardware. This should be indicating the hardware queue to use, not the ring
number.
Replace ring number with the hardware queue that should be used.
Note: SCSI avoided this issue as it utilized an older lfpc_issue_iocb
routine that properly adapts.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many io statistics were being sampled and saved using adapter-based data
structures. This was creating a lot of contention and cache thrashing in
the I/O path.
Move the statistics to the hardware queue data structures. Given the
per-queue data structures, use of atomic types is lessened.
Add new sysfs and debugfs stat routines to collate the per hardware queue
values and report at an adapter level.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Similar to the io execution path that reports cpu context information, the
debugfs routines for cpu information needs to be aligned with new hardware
queue implementation.
Convert debugfs cnd nvme cpucheck statistics to report information per
Hardware Queue.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Both NVME and SCSI aborts are now processed off the CQ workqueue and do not
generate events for the slowpath any more.
Remove the unused event code.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Once the IO buff allocations were made shared, there was a single XRI
buffer list shared by all hardware queues. A single list isn't great for
performance when shared across the per-cpu hardware queues.
Create a separate XRI IO buffer get/put list for each Hardware Queue. As
SGLs and associated IO buffers get allocated/posted to the firmware; round
robin their assignment across all available hardware Queues so that there
is an equitable assignment.
Modify SCSI and NVME IO submit code paths to use the Hardware Queue logic
for XRI allocation.
Add a debugfs interface to display hardware queue statistics
Added new empty_io_bufs counter to track if a cpu runs out of XRIs.
Replace common_ variables/names with io_ to make meanings clearer.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, both nvme and fcp each have their own concept of an io_channel,
which is a combination wq/cq and associated msix. Different cpus would
share an io_channel.
The driver is now moving to per-cpu wq/cq pairs and msix vectors. The
driver will still use separate wq/cq pairs per protocol on each cpu, but
the protocols will share the msix vector.
Given the elimination of the nvme and fcp io channels, the module
parameters will be removed. A new parameter, lpfc_hdw_queue is added which
allows the wq/cq pair allocation per cpu to be overridden and allocated to
lesser value. If lpfc_hdw_queue is zero, the number of pairs allocated will
be based on the number of cpus. If non-zero, the parameter specifies the
number of queues to allocate. At this time, the maximum non-zero value is
64.
To manage this new paradigm, a new hardware queue structure is created to
track queue activity and relationships.
As MSIX vector allocation must be known before setting up the
relationships, msix allocation now occurs before queue datastructures are
allocated. If the number of vectors allocated is less than the desired
hardware queues, the hardware queue counts will be reduced to the number of
vectors
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a extra queue and msix vector for expresslane. Now that the driver
will be doing queues per cpu, this oddball queue is no longer needed.
Expresslane will utilize the normal per-cpu queues.
Updated debugfs sli4 queue output to go along with the change
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, both NVME and SCSI get their IO buffers from separate
pools. XRI's are associated 1:1 with IO buffers, so XRI's are also split
between protocols.
Eliminate the independent pools and use a single pool. Each buffer
structure now has a common section and a protocol section. Per protocol
routines for SGL initialization are removed and replaced by common
routines. Initialization of the buffers is only done on the common area.
All other fields, which are protocol specific, are initialized when the
buffer is allocated for use in the per-protocol allocation routine.
In the past, the SCSI side allocated IO buffers as part of slave_alloc
calls until the maximum XRIs for SCSI was reached. As all XRIs are now
common and may be used for either protocol, allocation for everything is
done as part of adapter initialization and the scsi side has no action in
slave alloc.
As XRI's are no longer split, the lpfc_xri_split module parameter is
removed.
Adapters based on SLI3 will continue to use the older scsi_buf_list_get/put
routines. All SLI4 adapters utilize the new IO buffer scheme
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvme_prep_io_cmd() checks for null pnode, but caller
lpfc_nvme_fcp_io_submit() has already ensured it's non-null.
Remove the pnode null check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An hba-wide lock is taken in the nvme io completion routine. The lock
covers null'ing of the nrport pointer in the cmd structure.
The nrport member isn't necessary. After extracting the pointer from the
command, the pointer was dereferenced to get the fc discovery node
pointer. But the fc discovery node pointer is alrady in the command
structure so the dereferrence was unnecessary.
Eliminated the nrport structure member and its use, which also eliminates
the port-wide lock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For eh_bus_reset, driver is supposed to reset the link. Current option to
reset the link is applicable to Loop only. This patch updates current FW
option with the one that is applicable to all topologies.
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When loop was made down explicitly due to cable pull, then for N2N toplogy,
if FAWWPN BIT is enabled by user, then it would restore some default
(garbage) value for Physical port WWPN, so this show garbage WWPN for the
port. Fix is, to restore physical port WWPN, if it is fabric
configuration. When loop is explicitly made down, and FAWWPN feature is
enabled, then driver need to restore original flashed WWPN.
Signed-off-by: Sawan Chandak <schandak@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes memory leak by releasing DMA memory in case CT request and
response allocation fails.
Signed-off-by: Quinn Tran <qtran@marvall.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes SRB allocation flag from GFP_KERNEL to GFP_ATOMIC, to
prevent sleeping in IRQ context
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch flushes del_work and free_work while sending NACK response for
PRLI
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allocates DMA memory to prevent NULL pointer access for ct_sns
request while sending switch commands.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On Transmit respond in target mode, if the chip is already reset or the
session is already deleted, then advance the command to the free step.
There is no need to abort the command, because the chip has already flushed
it.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On session cleanup, either an implicit LOGO or an implicit PRLO is used to
flush IOs. If the flush command hit Queue Full condition, then it is
dropped. This patch adds retry code to prevent command drop.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provide call back functions to stop the chip and resume the chip
if the PCI lower level driver wants to perform function level reset/FLR.
Before the FLR, the chip will be stopped to turn off all DMA activity.
After the FLR, the chip is reset to resume previous operation state.
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the issue where Dell-EMC Target will fail to discover LUNs
if domain and area of port ID is not same as adapter's.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No users left.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No more need in a blk-mq world where the scsi command and request are
allocated together.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No real need for bidi support once the OSD code is gone.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that all the users are gone the SCSI OSD library can be removed as
well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We can just stash away the second request in struct bsg_job instead of
using the block layer req->next_rq field, allowing for the eventual removal
of the latter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated driver version to 27.102.00.00 from 27.101.00.00.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add Atlas PCIe Switch Management Port device PNPID,
Vendor Id: 0x1000
device Id: 0x00B2
This device is based on MPI 2.6 spec and it exposes one SES device to
accept management commands for the PCIe switch.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added device ID for NVMe Switch Adapter (Ambrosia).
VID: 0x1000
DID: 0x02B1
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MPI Endpoint is a PCIe switch based on MPI2.
Renaming device ID macro from MPI2_MFGPAGE_DEVID_SAS2308_MPI_EP to
MPI2_MFGPAGE_DEVID_SWITCH_MPI_EP.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for the new DEVICE_LIST DCMD.
Driver currently sends two separate DCMDs for getting the list of PDs and
LDs that are exposed to host. The new DCMD provides a single interface to
get a list of both PDs and LDs that are exposed to the host. Based on the
list of target IDs that are returned by this DCMD, driver will add the
devices (PD/LD) to SML. Driver will check for FW support for this new DCMD
and based on the support will either send the new DCMD or will fall back to
the earlier method of sending two separate DCMDs for PD and LD list.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation of adding support for the DEVICE_LIST DCMD, this patch
refactors the code in the AEN event handling path. Add new function to
update the PD and LD list in driver. Move the code to scan PD and VD
channels into separate function.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During FW init, combine the code to get the PD and LD list from FW into a
single function. This patch is in preparation for adding support for
HOST_DEVICE_LIST DCMD.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Presently when an error is encountered during probe of the cxlflash
adapter, a deadlock is seen with cpu thread stuck inside
cxlflash_remove(). Below is the trace of the deadlock as logged by
khungtaskd:
cxlflash 0006:00:00.0: cxlflash_probe: init_afu failed rc=-16
INFO: task kworker/80:1:890 blocked for more than 120 seconds.
Not tainted 5.0.0-rc4-capi2-kexec+ #2
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/80:1 D 0 890 2 0x00000808
Workqueue: events work_for_cpu_fn
Call Trace:
0x4d72136320 (unreliable)
__switch_to+0x2cc/0x460
__schedule+0x2bc/0xac0
schedule+0x40/0xb0
cxlflash_remove+0xec/0x640 [cxlflash]
cxlflash_probe+0x370/0x8f0 [cxlflash]
local_pci_probe+0x6c/0x140
work_for_cpu_fn+0x38/0x60
process_one_work+0x260/0x530
worker_thread+0x280/0x5d0
kthread+0x1a8/0x1b0
ret_from_kernel_thread+0x5c/0x80
INFO: task systemd-udevd:5160 blocked for more than 120 seconds.
The deadlock occurs as cxlflash_remove() is called from cxlflash_probe()
without setting 'cxlflash_cfg->state' to STATE_PROBED and the probe thread
starts to wait on 'cxlflash_cfg->reset_waitq'. Since the device was never
successfully probed the 'cxlflash_cfg->state' never changes from
STATE_PROBING hence the deadlock occurs.
We fix this deadlock by setting the variable 'cxlflash_cfg->state' to
STATE_PROBED in case an error occurs during cxlflash_probe() and just
before calling cxlflash_remove().
Cc: stable@vger.kernel.org
Fixes: c21e0bbfc485("cxlflash: Base support for IBM CXL Flash Adapter")
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several issues with badly indented statements. Fix these
and clean up the formatting.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mahesh Rajashekhara <mahesh.rajashekhara@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit bbc0f8bd88.
It added a warning whose intent was to check whether the rport was still
linked into the peer list. It doesn't work as intended and gives false
positive warnings for two reasons:
1) If the rport is never linked into the peer list it will not be
considered empty since the list_head is never initialized.
2) If the rport is deleted from the peer list using list_del_rcu(), then
the list_head is in an undefined state and it is not considered empty.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit bf50545696 ("block: Introduce blk_revalidate_disk_zones()")
inadvertently broke the message output of sd_zbc_print_zones() because the
zone information initialization of the scsi disk structure was moved to the
second scan run while sd_zbc_print_zones() is called on the first
scan. This leads to the following incorrect message to be printed for any
ZBC or ZAC zoned disks.
"...[sdX] 4294967295 zones of 0 logical blocks + 1 runt zone"
Fix this by initializing sdkp zone size and number of zones early on the
first scan. This does not impact the execution of
blk_revalidate_zones(). This functions is still called only once the block
device capacity is set on the second revalidate run on boot, or if the disk
zone configuration changed (i.e. the disk changed).
Fixes: bf50545696 ("block: Introduce blk_revalidate_disk_zones()")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no need to call twice string_get_size() when the capacity messages
are not going to be printed. Reverse the message output condition to return
early and avoid executing string_get_size() when it is not necessary.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
uic errors are currently printed out of time order.
Make things more readable by printing logs in time order, and printing
"No record" if history is empty.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to the patch that makes TMF handling synchronous the
write_pending_status() callback function is no longer called. Hence remove
it.
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Five minor bug fixes. The libfc one is a tiny memory leak, the zfcp
one is an incorrect user visible parameter and the rest are on error
legs or obscure features.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXFTUrCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishe/hAQCDic6S
FcD8TPv4jAt3qWun5vVCFAGCEuGet73p89sxpQEA51KcGrFjR9oCtZkd9nIzJL7M
enGaQ0RtT8wPMSUNklE=
=t6p4
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five minor bug fixes.
The libfc one is a tiny memory leak, the zfcp one is an incorrect user
visible parameter and the rest are on error legs or obscure features"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: 53c700: pass correct "dev" to dma_alloc_attrs()
scsi: bnx2fc: Fix error handling in probe()
scsi: scsi_debug: fix write_same with virtual_gb problem
scsi: libfc: free skb when receiving invalid flogi resp
scsi: zfcp: fix sysfs block queue limit output for max_segment_size
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/csiostor/csio_attr.c: In function 'csio_fcoe_free_vnp':
drivers/scsi/csiostor/csio_attr.c:500:21: warning:
variable 'pln' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds new BIT detection to enable FC-NVMe feature in the driver.
[mkp: fixed Giridhar's SoB]
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The aic94xx driver is currently failing to load with errors like
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:03.0/0000:02:00.3/0000:07:02.0/revision'
Because the PCI code had recently added a file named 'revision' to every
PCI device. Fix this by renaming the aic94xx revision file to
aic_revision. This is safe to do for us because as far as I can tell,
there's nothing in userspace relying on the current aic94xx revision file
so it can be renamed without breaking anything.
Fixes: 702ed3be1b (PCI: Create revision file in sysfs)
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This call must have been missed when I reworked the debugfs feature for
upstreaming, so add it back.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A NULL-pointer dereference was introduced for TMF SSP commands from the
upstreaming reworking.
Fix this by relocating the scsi_get_prot_op() callsite.
Fixes: d6a9000b81 ("scsi: hisi_sas: Add support for DIF feature for v2 hw")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sparse detected some problems in the driver, so tidy them up.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some sizes we allocate for debugfs structure are incorrect, so fix them.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hot-plugging SAS wire of direct hard disk backplane may cause disk lost. We
have done this test with several types of SATA disk from different venders,
and only two models from Seagate has this problem, ST4000NM0035-1V4107 and
ST3000VM002-1ET166.
The root cause is that the disk doesn't send D2H frame after OOB finished.
SAS controller will issue phyup interrupt only when D2H frame is received,
otherwise, will be waiting there all the time.
When this issue happen, we can find the disk again with link reset. To fix
this issue, we setup an timer after OOB finished. If the PHY is not up in
20s, do link reset. Notes: the 20s is an experience value.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS controller cannot support a programmed minimum linkrate of > 1.5G
(it will always negotiate to 1.5G at least), so just reject it.
This solves a strange situation where the PHY negotiated linkrate may be
less than the programmed minimum linkrate.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_alloc(), parameter shost is not used, so remove it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When issing a hardreset to a SATA device when running IO, it is possible
that abnormal CQs of the device are returned. Then enter error handler, it
doesn't enter function hisi_sas_abort_task() as there is no timeout IO, and
it doesn't set device as HISI_SAS_DEV_EH. So when hardreset by libata
later, it actually doesn't issue hardreset as there is a check to judge
whether device is in error.
For this situation, actually need to hardreset the device to recover.
So remove the check of sas_dev status in hisi_sas_I_T_nexus_reset().
Before we add the check to avoid the endless loop of reset for
directly-attached SATA device at probe time, actually we flutter it for
it, so it is not necessary to add the check now.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When injecting 2 bit ECC error, it will cause fatal AXI interrupts. Before
the recovery of SAS controller reset, the internal of SAS controller is in
error. If CQ interrupts return at the time, actually it is exception CQ
interrupt, and it may cause resource release in disorder.
To avoid the exception situation, shutdown AXI bus after fatal AXI
interrupt. In SAS controller reset, it will restart AXI bus. For later
version of v3 hw, hardware will shutdown AXI bus for this situation, so
just fix current ver of v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Send primitive NOTIFY to SSP situation only, or it causes underflow issue
when sending IO. Also rename hisi_sas_hw.sl_notify() to hisi_sas_hw.
sl_notify_ssp().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch creates debugfs file for ITCT and adds file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sparse can detect some type casting issues in the debugfs code, so fix it
up.
Also a missing static qualifier is added to hisi_sas_debugfs_to_reg_name().
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "hostdata->dev" pointer is NULL here. We set "hostdata->dev = dev;"
later in the function and we also use "hostdata->dev" when we call
dma_free_attrs() in NCR_700_release().
This bug predates git version control.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two issues here. First if cmgr->hba is not set early enough then
it leads to a NULL dereference. Second if we don't completely initialize
cmgr->io_bdt_pool[] then we end up dereferencing uninitialized pointers.
Fixes: 853e2bd210 ("[SCSI] bnx2fc: Broadcom FCoE offload driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns:
drivers/scsi/pcmcia/nsp_cs.c:1137:27: warning: equality comparison with
extraneous parentheses [-Wparentheses-equality]
if ((tmpSC->SCp.Message == MSG_COMMAND_COMPLETE)) {
~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/pcmcia/nsp_cs.c:1137:27: note: remove extraneous
parentheses around the comparison to silence this warning
if ((tmpSC->SCp.Message == MSG_COMMAND_COMPLETE)) {
~ ^ ~
drivers/scsi/pcmcia/nsp_cs.c:1137:27: note: use '=' to turn this
equality comparison into an assignment
if ((tmpSC->SCp.Message == MSG_COMMAND_COMPLETE)) {
^~
=
1 warning generated.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns:
drivers/scsi/nsp32.c:2444:14: warning: explicitly assigning value of
variable of type 'unsigned char' to itself [-Wself-assign]
offset = offset;
~~~~~~ ^
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: GOTO Masanori <gotom@debian.or.jp>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The WRITE SAME(10) and (16) implementations didn't take account of the
buffer wrap required when the virtual_gb parameter is greater than 0.
Fix that and rename the fake_store() function to lba2fake_store() to lessen
confusion with the global fake_storep pointer. Bump version date.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the Kbuild core manipulates header search paths in a crazy way
[1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to the
search paths in the srctree. Some Makefiles are already written in that
way, but not all. The goal of this work is to make the notation consistent,
and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5b
("kbuild: do not drop -I without parameter").
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I was able to build without these extra header search paths.
Especially, the header search path -I. in kernel Makefiles is always
suspicious; it allows the compiler to search for headers in the top of
$(srctree), where obviously no header file exists.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The issue to be fixed in this commit is when libfc found it received a
invalid FLOGI response from FC switch, it would return without freeing the
fc frame, which is just the skb data. This would cause memory leak if FC
switch keeps sending invalid FLOGI responses.
This fix is just to make it execute `fc_frame_free(fp)` before returning
from function `fc_lport_flogi_resp`.
Signed-off-by: Ming Lu <ming.lu@citrix.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/fnic/vnic_wq.c: In function 'vnic_wq_alloc_bufs':
drivers/scsi/fnic/vnic_wq.c:50:19: warning:
variable 'vdev' set but not used [-Wunused-but-set-variable]
drivers/scsi/fnic/vnic_rq.c: In function 'vnic_rq_alloc_bufs':
drivers/scsi/fnic/vnic_rq.c:30:19: warning:
variable 'vdev' set but not used [-Wunused-but-set-variable]
Never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the READ(6) and WRITE(6) commands interpret a zero in the transfer
length field in the CDB as 256 logical blocks, avoid submitting such
commands.
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the function scsi_to_u32() is identical to get_unaligned_be32(),
change all scsi_to_u32() calls into get_unaligned_be32() calls.
Cc: Jian Luo <luojian5@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Cc: qla2xxx-upstream@qlogic.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Cc: QLogic-Storage-Upstream@cavium.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Cc: Karan Tilak Kumar <kartilak@cisco.com>
Cc: Sesidhar Baddela <sebaddel@cisco.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Cc: Satish Kharat <satishkh@cisco.com>
Cc: Sesidhar Baddela <sebaddel@cisco.com>
Cc: Karan Tilak Kumar <kartilak@cisco.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Varun Prakash <varun@chelsio.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Oza Pawandeep <poza@codeaurora.org>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
[mkp: removed unused label]
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There's no need to export fcoe_ctlr_destroy_store as a symbol, so remove
the EXPORT_SYMBOL() line for it.
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We are trying to get rid of BUS_ATTR() and the usage of that in the fcoe
driver can be trivially converted to use BUS_ATTR_WO(), so use that
instead.
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Six fixes, all of which appear to have user visible consequences. The
DMA one is a regression fix from the merge window and of the others,
four are driver specific and one specific to the target code.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXEt6GSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbxoAP0R0z0J
fdCRn9AMRbZ3xJzD+E6V2gw38Gdgm8rR5mT1gQEAv1VxZwOAb9Qxbcr+l4uybqZr
Q55H31I/IvBgNm84jH0=
=vkW7
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes, all of which appear to have user visible consequences.
The DMA one is a regression fix from the merge window and of the
others, four are driver specific and one specific to the target code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: Use explicit access size in ufshcd_dump_regs
scsi: tcmu: fix use after free
scsi: csiostor: fix NULL pointer dereference in csio_vport_set_state()
scsi: lpfc: nvmet: avoid hang / use-after-free when destroying targetport
scsi: lpfc: nvme: avoid hang / use-after-free when destroying localport
scsi: communicate max segment size to the DMA mapping code
From Ching Huang <ching2048@areca.com.tw>
Update driver version to v1.40.00.10-20190116.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
For ACB_ADAPTER_TYPE_B controller, the read/write after hibernate and
resume may sometimes result in 'isr get an illegal ccb command' in
/var/log/messages. This patch fixes it.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
dma_zalloc_coherent will be phased out. Use dma_alloc_coherent instead.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update fnic driver to version 1.6.0.47.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds changes to check if fnic devcmd2 interface is exported by
the firmware. If devcmd2 interfaces is exported, driver starts using it
else falls back to fnic devcmd1 interface.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds fnic devcmd2 interfaces for initialization and posting
commands to fw.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the devcmd2 wq initalization and devcmd2 ring allocation
helper interfaces used by devcmd2 init.
[mkp: typos]
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the fnic devcmd2 controller definitions.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the fnic devcmd2 command structre and the command result
structure definitions.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Impose an upper limit on the max number of CQ entries (corresponding to the
copy wq) processed in an interrupt. Use module parameter to set the limit.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do RQ enable before posting descriptor. This is needed for later hw
revisions.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Doing vnic_device_enable before this could cause interrupts to happen
before they are setup.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change is to print warning when scsi done is called for an IO that has
not yet been issued to the fw. Also adding sc and tag to debug print when
IO is cleaned up.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change is to add fnic stats for the max number of CQs (corresponding
to copy WQ) processed in a given interrupt, max time taken by the ISR.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the current fnic port speed stat to fnic debug stats.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Need to use fnic_lock as well as host lock in that order to set state
flags.
[mkp: typos]
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
rq->ctrl not enabled when this is called is bad but not fatal and can
continue.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch changes the default lun queuedepth for fnic to 256.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to add fnic 20G port speed display in sysfs.
[mkp: typo]
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From scsi_init_command(), a function called by scsi_mq_prep_fn():
/* zero out the cmd, except for the embedded scsi_request */
memset((char *)cmd + sizeof(cmd->req), 0,
sizeof(*cmd) - sizeof(cmd->req) + dev->host->hostt->cmd_size);
In other words, scsi_mq_prep_fn() clears scsi_cmnd.flags. Hence move the
clear_bit() call into the else branch, the only branch in which this code
is necessary.
See also commit f1342709d1 ("scsi: Do not rely on blk-mq for double
completions").
Cc: Keith Busch <keith.busch@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes the source code more uniform and does not change any
functionality.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: extracted this patch from a larger patch ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rework sd_setup_read_write_cmnd() so it becomes more readable. Put all the
sanity checking at the head of the function and sanitize the logged error
messages. Move the legacy SCSI logging calls to the end of the functions
and reduce conditional nesting.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a helper function for each of the 6, 10, 16 and 32-byte READ/WRITE
variants and use those when setting up reads and writes.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 and made
function names shorter. ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid open coding the checks for the supported logical block sizes and use
a mask to check for misaligned I/O. Use our helper functions to scale lba
and block count.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have had several bugs due mixing sector and logical block size
terminology. In the block layer, a sector is a 512-byte unit regardless of
the logical block size of the underlying device. But the term "sector" is
still widely used in sd.c when referring to logical block sized units.
We previously introduced helper functions such as sectors_to_logical() and
logical_to_sectors() to make the distinction clear. Use these to make the
code in sd.c consistent wrt. logical blocks and block layer sectors.
Use "lba" to describe a logical block address and "nr_blocks" when counting
logical blocks. SBC uses "TRANSFER LENGTH" to describe the latter but this
term was avoided to prevent confusion with the very similar DMA transfer
size (->transfersize) which is counted in bytes.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: extracted this patch from a larger patch ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Assign fc_vport to ln->fc_vport before calling csio_fcoe_alloc_vnp() to
avoid a NULL pointer dereference in csio_vport_set_state().
ln->fc_vport is dereferenced in csio_vport_set_state().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We cannot wait on a completion object in the lpfc_nvme_targetport structure
in the _destroy_targetport() code path because the NVMe/fc transport will
free that structure immediately after the .targetport_delete() callback.
This results in a use-after-free, and a hang if slub_debug=FZPU is enabled.
Fix this by putting the completion on the stack.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We cannot wait on a completion object in the lpfc_nvme_lport structure in
the _destroy_localport() code path because the NVMe/fc transport will free
that structure immediately after the .localport_delete() callback. This
results in a use-after-free, and a hang if slub_debug=FZPU is enabled.
Fix this by putting the completion on the stack.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a host driver sets a maximum segment size we should not only propagate
that setting to the block layer, which can merge segments, but also to the
DMA mapping layer which can merge segments as well.
Fixes: 50c2e9107f ("scsi: introduce a max_segment_size host_template parameters")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace nvram_* functions with static functions in nvram.h. These will
become wrappers for struct nvram_ops method calls.
This patch effectively disables existing NVRAM functionality so as to
allow the rest of the series to be bisected without build failures.
That functionality is gradually re-implemented in subsequent patches.
Replace the sole validate-checksum-and-read-byte sequence with a call to
nvram_read() which will gain the same semantics in subsequent patches.
Remove unused exports.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On powerpc, setting CONFIG_NVRAM=n builds a kernel with no NVRAM support.
Setting CONFIG_NVRAM=m enables the /dev/nvram misc device module without
enabling NVRAM support in drivers. Setting CONFIG_NVRAM=y enables the
misc device (built-in) and also enables NVRAM support in drivers.
m68k shares the valkyriefb driver with powerpc, and since that driver uses
NVRAM, it is affected by CONFIG_ATARI_SCSI, because of the use of
"select NVRAM". We can avoid the "select" here, but drivers still have
to interpret the CONFIG_NVRAM symbol consistently regardless of platform.
In this patch and the subsequent fbdev driver patch, the convention is
adopted across all relevant platforms whereby NVRAM functionality gets
enabled in a given device driver when the nvram misc device is built-in
or when both drivers are modules.
Acked-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A set of 17 fixes. Most of these are minor or trivial. The one fix
that may be serious is the isci one: the bug can cause hba parameters
to be set from uninitialized memory. I don't think it's exploitable,
but you never know.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXEKL0SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVZpAQCwuPTk
fqOt4v4hJ0oUHtEBsQK3VMXSdUvWdb5Lbn3WeQD/RFYTyNxcIF7ADSWw71b+IigT
ejUrMzI8ig+nZ1jbFZ4=
=BdS/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of 17 fixes. Most of these are minor or trivial.
The one fix that may be serious is the isci one: the bug can cause hba
parameters to be set from uninitialized memory. I don't think it's
exploitable, but you never know"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: add wait_for_completion()
scsi: qla1280: set 64bit coherent mask
scsi: ufs: Fix geometry descriptor size
scsi: megaraid_sas: Retry reads of outbound_intr_status reg
scsi: qedi: Add ep_state for login completion on un-reachable targets
scsi: ufs: Fix system suspend status
scsi: qla2xxx: Use correct number of vectors for online CPUs
scsi: hisi_sas: Set protection parameters prior to adding SCSI host
scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
scsi: isci: initialize shost fully before calling scsi_add_host()
scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
scsi: core: Synchronize request queue PM status only on successful resume
scsi: pm80xx: reduce indentation
scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
scsi: megaraid_sas: correct an info message
scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
scsi: sd: Fix cache_type_store()
CONFIG_SCSI_UFS_QCOM selects CONFIG_PHY_QCOM_UFS, assuming that this was
the only possible PHY driver Qualcomm's UFS controller would use. But in
SDM845, the UFS driver is bundled into phy-qcom-qmp, and phy-qcom-ufs is
unused.
Remove the select, since for SDM845 it adds useless drivers to the build.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case of ->set_param() and ->bind_conn() cxgb4i driver does not wait for
cmd completion, this can create race conditions, to avoid this add
wait_for_completion().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After Commit 54aed4dd35 ("MIPS: IP27: use dma_direct_ops") qla1280 driver
failed on SGI IP27 machines with
qla1280: QLA1040 found on PCI bus 0, dev 0
qla1280 0000:00:00.0: enabling device (0006 -> 0007)
qla1280: Failed to get request memory
qla1280: probe of 0000:00:00.0 failed with error -12
Reason is that SGI IP27 always generates 64bit DMA addresses and has no
fallback mode for 32bit DMA addresses implemented. QLA1280 supports 64bit
addressing for all DMA accesses so setting coherent mask to 64bit fixes the
issue.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Albeit we no longer rely on those hard-coded descriptor sizes, we still use
them as our defaults, so better get it right. While adding its sysfs
entries, we forgot to update the geometry descriptor size. It is 0x48
according to UFS2.1, and wasn't changed in UFS3.0.
[mkp: typo]
Fixes: c720c09122 (scsi: ufs: sysfs: geometry descriptor)
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The tmscsim.txt doc file was removed in c121107d0f.
Fixes: c121107d0f ("scsi: documentation: Obsolete documentation references")
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit 272652fcbf ("scsi: megaraid_sas: add retry logic in megasas_readl")
missed changing readl to megasas_readl in megasas_clear_intr_fusion(). For
Aero controllers, reads of outbound_intr_status register needs to be
retried.
Reported-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the driver finds invalid destination MAC for the first un-reachable
target, and before completes the PATH_REQ operation, set new ep_state to
OFFLDCONN_NONE so that as part of driver ep_poll mechanism, the upper
open-iscsi layer is notified to complete the login process on the first
un-reachable target and thus proceed login to other reachable targets.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
hba->is_sys_suspended is set after successful system suspend but
not clear after successful system resume.
According to current behavior, hba->is_sys_suspended will not be set if
host is runtime-suspended but not system-suspended. Thus we shall aligh the
same policy: clear this flag even if host remains runtime-suspended after
ufshcd_system_resume is successfully returned.
Simply fix this flag to correct host status logs.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the SMP PHY control execution result is checked, however the
function result for the command is not.
As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.
In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SGE buffer containing DIF information crosses 4G boundary, it results
in DMA error. This patch fixes this issue by calculating SGE buffer size
and if it crosses 4G boundary, driver will split it into multiple SGE
buffers to avoid DMA error.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow user to selectively enable/disable DIF/DIX protection
capabilities mask.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SCSI-MQ is enabled, in some case system would present
nr_possible_cpus() which is greater than requested vectors by the
driver. This results into driver being able to get larger number of MSI-X
vectors than actual online CPUs. Driver then uses
pci_alloc_irq_vectors_affinity() to assign 1:1 mapping and affinity for
each MSI-x vector to CPUs. When the command is submitted using MSI-x
vector, assigned to offline CPU, it results in an ABTS and system
hang. This hang is result of a driver not being able to process interrupt
on a vector assigned to an Off-line CPUs
This patch fixes this issue by setting irq_offset value for the
blk_mq_pci_map_queues() to use only those CPUs which has CPU mask affinity
assigned and are online. By using the irq_offset value, driver will allow
online cpumask to decide which vectors are used in blk_mq_pci_map_queues().
Fixes: 5601236b6f ("scsi: qla2xxx: Add Block Multi Queue functionality.")
Cc: <stable@vger.kernel.org> #4.19
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in some cases, I replaced "FALLTHROUGH" with a "fall through"
annotation and then placed it at the bottom of the corresponding switch
case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 114961 ("Missing break in switch")
Addresses-Coverity-ID: 114962 ("Missing break in switch")
Addresses-Coverity-ID: 114963 ("Missing break in switch")
Addresses-Coverity-ID: 114964 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "!!! fall through !!!"
comment with "fall through" annotations, which is what GCC is expecting to
find.
Addresses-Coverity-ID: 146155 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that I replaced "!! fall through !!" and "!!! fall through !!!"
comments with "fall through" annotations, which is what GCC is expecting to
find.
Addresses-Coverity-ID: 744899 ("Missing break in switch")
Addresses-Coverity-ID: 744900 ("Missing break in switch")
Addresses-Coverity-ID: 744901 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "!!! fall through !!!"
with a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Bradley Grove <bgrove@atto.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 114994 ("Missing break in switch")
Addresses-Coverity-ID: 114995 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we set the protection parameters after calling scsi_add_host()
for v3 hw.
They should be set beforehand, so make this change.
Appearantly this fixes our DIX issue (not mainline yet) also, but more
testing required.
Fixes: d6a9000b81 ("scsi: hisi_sas: Add support for DIF feature for v2 hw")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "allow fall-through" with
a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return statement is indented incorrectly, fix this by removing a single
tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the protection lookup tables in sd_prot_flag_mask() and
sd_prot_op() are declared as non-static. As such, they will be rebuilt for
each respective function call.
Optimise by making them static.
This saves ~100B object code for sd.c:
Before:
text data bss dec hex filename
25403 1024 16 26443 674b drivers/scsi/sd.o
After:
text data bss dec hex filename
25299 1024 16 26339 66e3 drivers/scsi/sd.o
In addition, since those same functions are declared in sd.h, but each are
only referenced in sd.c, relocate them to that same c file.
The inline specifier is dropped also, since gcc should be able to make the
decision to inline.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_mq_setup_tags(), which is called by scsi_add_host(), calculates the
command size to allocate based on the prot_capabilities. In the isci
driver, scsi_host_set_prot() is called after scsi_add_host() so the command
size gets calculated to be smaller than it needs to be. Eventually,
scsi_mq_init_request() locates the 'prot_sdb' after the command assuming it
was sized correctly and a buffer overrun may occur.
However, seeing blk_mq_alloc_rqs() rounds up to the nearest cache line
size, the mistake can go unnoticed.
The bug was noticed after the struct request size was reduced by commit
9d037ad707 ("block: remove req->timeout_list")
Which likely reduced the allocated space for the request by an entire cache
line, enough that the overflow could be hit and it caused a panic, on boot,
at:
RIP: 0010:t10_pi_complete+0x77/0x1c0
Call Trace:
<IRQ>
sd_done+0xf5/0x340
scsi_finish_command+0xc3/0x120
blk_done_softirq+0x83/0xb0
__do_softirq+0xa1/0x2e6
irq_exit+0xbc/0xd0
call_function_single_interrupt+0xf/0x20
</IRQ>
sd_done() would call scsi_prot_sg_count() which reads the number of
entities in 'prot_sdb', but seeing 'prot_sdb' is located after the end of
the allocated space it reads a garbage number and erroneously calls
t10_pi_complete().
To prevent this, the calls to scsi_host_set_prot() are moved into
isci_host_alloc() before the call to scsi_add_host(). Out of caution, also
move the similar call to scsi_host_set_guard().
Fixes: 3d2d752549 ("[SCSI] isci: T10 DIF support")
Link: http://lkml.kernel.org/r/da851333-eadd-163a-8c78-e1f4ec5ec857@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Intel SCU Linux support <intel-linux-scu@intel.com>
Cc: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for IOST and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for DQ and add file operations
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for CQ and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for port register and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for global register and add file
operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch takes snapshot for global regs, port regs, CQ, DQ, IOST, ITCT.
Add code for snapshot trig and generate dump directory.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allocates snapshot memory for global reg, port regs, CQ, DQ,
IOST, ITCT.
When we fail to allocate memory for some registers, we free the memory
and set hisi_sas_debugfs_enable as 0 to stop loading debugfs from running.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch creates root directory at hisi_sas_init() and generates device
directory when we probe device driver.
And we remove the root directory at hisi_sas_exit(), but recursively
delete device directory when we remove device driver.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Update driver version to v1.40.00.10-20181217
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Fix suspend/resume of ACB_ADAPTER_TYPE_B
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Separate 'set dma mask' as a function
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Add an option of set dma_mask_64 for ACB_ADAPTER_TYPE_A
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_D for >4gb ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_C for >4GB ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_B for >4GB ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_A for >4GB ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Merge arcmsr_alloc_io_queue to arcmsr_alloc_ccb_pool
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Rename arcmsr_free_mu to arcmsr_free_io_queue
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From Ching Huang <ching2048@areca.com.tw>
Rename acb structure member roundup_ccbsize to ioqueue_size
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API. Also switch
to dma_map_single from pci_map_page in one case where this makes the code
simpler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code has been under a never defined ifdef since the beginning
of time (or at least history), and has just bitrotted. Nuke it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This can't ever be compiled into the kernel, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code can't be built into the kernel without editing the source
file and is not generally useful.
[mkp: typo]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code has been under the never defined GDTH_RTC ifdef forever,
nuke it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove never compile in support for sending debug traces straight to
the serial port using direct port access.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The non-PCI code has bitrotted for quite a while and will just oops
on load because it passes a NULL pointer to the PCI DMA routines.
Lets kill it for good - if someone really wants to use one of these
cards I'll help mentoring them to write a proper driver glue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Out of the three callers once insists on the scratch buffer, and the
others are fine with a new allocation. Switch those two to just use
pci_alloc_consistent directly, and open code the scratch buffer
allocation in the remaining one. This avoids a case where we might
be doing a memory allocation under a spinlock with irqs disabled.
[mkp: typo]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gdth_show_info currently allocs and frees a dma buffer four times which
isn't very efficient. Reuse a single allocation instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This function is a huge mess with duplicated error handling. Split out
a few useful helpers and use goto labels to untangle the error handling
and no-data ioctl handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "Drop thru" and "Fall
Thru" with "fall through" annotations, which is what GCC is expecting to
find.
Also, in some cases a dash is added as a token in order to separate the
"fall through" annotation from the rest of the comment on the same line,
which is what GCC is expecting to find.
Addresses-Coverity-ID: 114979 ("Missing break in switch")
Addresses-Coverity-ID: 114980 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix boolean expression by using logical AND operator '&&' instead of
bitwise operator '&'.
This issue was detected with the help of Coccinelle.
Fixes: 1e46731efd ("scsi: smartpqi: check for null device pointers")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The commit 356fd2663c ("scsi: Set request queue runtime PM status back to
active on resume") fixed up the inconsistent RPM status between request
queue and device. However changing request queue RPM status shall be done
only on successful resume, otherwise status may be still inconsistent as
below,
Request queue: RPM_ACTIVE
Device: RPM_SUSPENDED
This ends up soft lockup because requests can be submitted to underlying
devices but those devices and their required resource are not resumed.
For example,
After above inconsistent status happens, IO request can be submitted to UFS
device driver but required resource (like clock) is not resumed yet thus
lead to warning as below call stack,
WARN_ON(hba->clk_gating.state != CLKS_ON);
ufshcd_queuecommand
scsi_dispatch_cmd
scsi_request_fn
__blk_run_queue
cfq_insert_request
__elv_add_request
blk_flush_plug_list
blk_finish_plug
jbd2_journal_commit_transaction
kjournald2
We may see all behind IO requests hang because of no response from storage
host or device and then soft lockup happens in system. In the end, system
may crash in many ways.
Fixes: 356fd2663c (scsi: Set request queue runtime PM status back to active on resume)
Cc: stable@vger.kernel.org
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Delete tab aligning a statement with the right hand side of a preceding
assignment rather than the left hand side.
Found with the help of Coccinelle.
[mkp: added space]
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return code should be check while qla4xxx_copy_from_fwddb_param fails.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was apparently forgotten in
894169db1 ("scsi: megaraid_sas: Use 63-bit DMA addressing").
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Changing of caching mode via /sys/devices/.../scsi_disk/.../cache_type may
fail if device responds to MODE SENSE command with DPOFUA flag set, and
then checks this flag to be not set on MODE SELECT command.
In this scenario, when trying to change cache_type, write always fails:
# echo "none" >cache_type
bash: echo: write error: Invalid argument
And following appears in dmesg:
[13007.865745] sd 1:0:1:0: [sda] Sense Key : Illegal Request [current]
[13007.865753] sd 1:0:1:0: [sda] Add. Sense: Invalid field in parameter list
From SBC-4 r15, 6.5.1 "Mode pages overview", description of DEVICE-SPECIFIC
PARAMETER field in the mode parameter header:
...
The write protect (WP) bit for mode data sent with a MODE SELECT
command shall be ignored by the device server.
...
The DPOFUA bit is reserved for mode data sent with a MODE SELECT
command.
...
The remaining bits in the DEVICE-SPECIFIC PARAMETER byte are also reserved
and shall be set to zero.
[mkp: shuffled commentary to commit description]
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
This is two simple target fixes and one discard related I/O starvation
problem in sd. The discard problem occurs because the discard page
doesn't have a mempool backing so if the allocation fails due to
memory pressure, we then lose the forward progress we require if the
writeout is on the same device. The fix is to back it with a mempool.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXB2mCiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSJmAP9E8ItG
tSgUyIfRRcn/ZxYdfOg1EWxGgDq17Fq2TgQU3gEAolSLwol7eKl1hQnDpOKPVMmC
//j4JyKpCl3EEvNs6DQ=
=3Hmt
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is two simple target fixes and one discard related I/O starvation
problem in sd.
The discard problem occurs because the discard page doesn't have a
mempool backing so if the allocation fails due to memory pressure, we
then lose the forward progress we require if the writeout is on the
same device. The fix is to back it with a mempool"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: use mempool for discard special page
scsi: target: iscsi: cxgbit: add missing spin_lock_init()
scsi: target: iscsi: cxgbit: fix csk leak
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, a dash is added as a token in order
to separate the "Fall through" annotation from the rest of the comment on
the same line, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, a dash is added as a token in order
to separate the "Fall through" annotations from the rest of the comment on
the same line, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, a dash is added as a token in order
to separate the "fall through" annotations from the rest of the comment on
the same line, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 703127 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This commit enhances iscsi initiator modules to capture iscsi debug
messages using linux kernel tracepoint facility:
https://www.kernel.org/doc/Documentation/trace/tracepoints.txt
The following tracepoint events have been created under the iscsi
tracepoint event group:
iscsi_dbg_conn - to capture connection debug messages (libiscsi module)
iscsi_dbg_session - to capture session debug messages (libiscsi module)
iscsi_dbg_eh - to capture error handling debug messages (libiscsi module)
iscsi_dbg_tcp - to capture iscsi tcp debug messages (libiscsi_tcp module)
iscsi_dbg_sw_tcp - to capture iscsi sw tcp debug messages (iscsi_tcp module)
iscsi_dbg_trans_session - to cpature iscsi transsport sess debug messages
(scsi_transport_iscsi module)
iscsi_dbg_trans_conn - to capture iscsi transport conn debug messages
(scsi_transport_iscsi module)
[mkp: typos]
Signed-off-by: Fred Herard <fred.herard@oracle.com>
Reviewed-by: Rajan Shanmugavelu <rajan.shanmugavelu@oracle.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 1465234 ("Missing break in switch")
Addresses-Coverity-ID: 1465238 ("Missing break in switch")
Addresses-Coverity-ID: 1465242 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 1475400 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/fcoe/fcoe.c: In function 'fcoe_recv_frame':
drivers/scsi/fcoe/fcoe.c:1672:20: warning:
variable 'port' set but not used [-Wunused-but-set-variable]
drivers/scsi/fcoe/fcoe.c: In function 'fcoe_device_notification':
drivers/scsi/fcoe/fcoe.c:1861:20: warning:
variable 'port' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We must free all irqs during shutdown, else kexec's 2nd kernel would hang
in pqi_wait_for_completion_io() as below:
Call trace:
pqi_wait_for_completion_io
pqi_submit_raid_request_synchronous.constprop.78+0x23c/0x310 [smartpqi]
pqi_configure_events+0xec/0x1f8 [smartpqi]
pqi_ctrl_init+0x814/0xca0 [smartpqi]
pqi_pci_probe+0x400/0x46c [smartpqi]
local_pci_probe+0x48/0xb0
pci_device_probe+0x14c/0x1b0
really_probe+0x218/0x3fc
driver_probe_device+0x70/0x140
__driver_attach+0x11c/0x134
bus_for_each_dev+0x70/0xc8
driver_attach+0x30/0x38
bus_add_driver+0x1f0/0x294
driver_register+0x74/0x12c
__pci_register_driver+0x64/0x70
pqi_init+0xd0/0x10000 [smartpqi]
do_one_initcall+0x60/0x1d8
do_init_module+0x64/0x1f8
load_module+0x10ec/0x1350
__se_sys_finit_module+0xd4/0x100
__arm64_sys_finit_module+0x28/0x34
el0_svc_handler+0x104/0x160
el0_svc+0x8/0xc
This happens only in the following combinations:
1. smartpqi is built as module, not built-in;
2. We have a disk connected to smartpqi card;
3. Both kexec's 1st and 2nd kernels use this disk as Rootfs' mount point.
Signed-off-by: Yanjiang Jin <yanjiang.jin@hxt-semitech.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix kbuild warning and fallout from linux-next -Wimplicit-fallthrough.
[mkp: added fall through statements]
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
- need to bump up the driver version because
of the OFA patch and the fw status register
read timeout patch.
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- when OFA event occurs, driver will stop traffic to RAID/HBA path. Driver
waits for all the outstanding requests to complete.
- Driver sends OFA event acknowledgment to firmware.
- Driver will wait until the new firmware is up and running.
- Driver will free up the resources.
- Driver calls SIS/PQI initialization and rescans the device list.
- Driver will resume the traffic to RAID/HBA path.
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Problem:
- during the driver initialization, driver will poll fw
for KERNEL_UP in a 30 seconds timeout.
- if the firmware is not ready after 30 seconds,
driver will not be loaded.
Fix:
- change timeout from 30 seconds to 3 minutes.
Reported-by: Feng Li <lifeng1519@gmail.com>
Reviewed-by: Ajish Koshy <ajish.koshy@microsemi.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Problem:
The Linux kernel takes a logical volume offline after a LUN reset. This is
generally accompanied by this message in the dmesg output:
Device offlined - not ready after error recovery
Root Cause:
The root cause is a "quirk" in the timeout handling in the Linux SCSI
layer. The Linux kernel places a 30-second timeout on most media access
commands (reads and writes) that it send to device drivers. When a media
access command times out, the Linux kernel goes into error recovery mode
for the LUN that was the target of the command that timed out. Every
command that timed out is kept on a list inside of the Linux kernel to be
retried later. The kernel attempts to recover the command(s) that timed out
by issuing a LUN reset followed by a TEST UNIT READY. If the LUN reset and
TEST UNIT READY commands are successful, the kernel retries the command(s)
that timed out.
Each SCSI command issued by the kernel has a result field associated with
it. This field indicates the final result of the command (success or
error). When a command times out, the kernel places a value in this result
field indicating that the command timed out.
The "quirk" is that after the LUN reset and TEST UNIT READY commands are
completed, the kernel checks each command on the timed-out command list
before retrying it. If the result field is still "timed out", the kernel
treats that command as not having been successfully recovered for a
retry. If the number of commands that are in this state are greater than
two, the kernel takes the LUN offline.
Fix:
When our RAIDStack receives a LUN reset, it simply waits until all
outstanding commands complete. Generally, all of these outstanding commands
complete successfully. Therefore, the fix in the smartpqi driver is to
always set the command result field to indicate success when a request
completes successfully. This normally isn’t necessary because the result
field is always initialized to success when the command is submitted to the
driver. So when the command completes successfully, the result field is
left untouched. But in this case, the kernel changes the result field
behind the driver’s back and then expects the field to be changed by the
driver as the commands that timed-out complete.
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- fix race condition when a unit is deleted after an RLL,
and before we have gotten the LV_STATUS page of the unit.
- In this case we will get a standard inquiry, rather than
the desired page. This will result in a unit presented
which no longer exists.
- If we ask for LV_STATUS, insure we get LV_STATUS
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Ajish Koshy <ajish.koshy@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- wait on all outstanding I/O to complete before the device is removed.
- check for null device pointers in IO entry/completion functions.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
