Introduce U-APSD support in mt76 driver for AP interface
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For consistency with the rest of the code always rely on defined
macros for register access
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
kernel test robot <lkp@intel.com> found the following issue
and Kalle Valo forwarded it to Linux wireless.
drivers/net/wireless/mediatek/mt76/pci.c:8:6:
warning: no previous prototype for 'mt76_pci_disable_aspm'
Fix this by adding the missing include of mt76.h as Kalle
suggested.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
While looking at the ETSI regulatory domain definitions
and a patch, which allows more channels for ath10k, I also
checked the channels allowed for mt76.
ETSI regulations would possibly allow to add channels 32, 68,
96, 144, 169 and 173. IEEE 802.11-2016 defines no operating class
for channels 32, 68 and 96. This leaves us channels 144, 169 and 173,
which are included in this patch.
I tested 169 and 173 with a mt76 based USB dongle (AVM AC 860) and they
worked fine. If I saw that right, these channels are also covered by
register definitions inside the driver.
Channel 144 should also work, but gets disabled by the kernel as of now.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix up typo in Kconfig with indicating MT7663U is an 802.11ac device
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_for_each_q_rx whenever possible in order to simply the code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7622/mt7663 chipsets rely on a fixed reverse queue map order respect
to mac80211 one:
- q(0): IEEE80211_AC_BK
- q(1): IEEE80211_AC_BE
- q(2): IEEE80211_AC_VI
- q(3): IEEE80211_AC_VO
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
acs and wmm index are swapped in mt7615_queues_acq respect to the hw
design
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Coverage class callback can potentially run in parallel with other
routines (e.g. mt7615_set_channel) that configures timing registers.
Run coverage class callback holding mt76 mutex
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Avoid adding MT7615_EEPROM_SIZE twice.
Rename MT7615_EEPROM_EXTRA_DATA to MT7615_EEPROM_FULL_SIZE, since it already
includes MT7615_EEPROM_SIZE
Fixes: ad380ad1eb ("mt76: mt7615: add support for applying DC offset calibration from EEPROM")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622150716.49622-1-nbd@nbd.name
Fix the two following memory leaks in mt7663u_probe:
1- if device power-own times out, remove ieee80211 hw device.
2- if mt76u queues allocation fails, remove pending urbs.
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/e4098f0c8a9ac51997de07f38c2bcdf7042d6db1.1592755166.git.lorenzo@kernel.org
Fixes a crash on MMIO devices when running into the watchdog reset
Fixes: d3377b78ce ("mt76: add HE phy modes and hardware queue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200615181341.81871-1-nbd@nbd.name
* tx queueing fixes for mt7615/22/63
* locking fix
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAl7dBRsACgkQ130UHQKnbvUpiQCgjHAeT1fOKnFfFF5kHzECEyFS
1N8An0endTyFWAXCZd3aEgK4/nQN4LwR
=6f32
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2020-06-07' of https://github.com/nbd168/wireless
mt76 patches for 5.8
* tx queueing fixes for mt7615/22/63
* locking fix
# gpg: Signature made Sun 07 Jun 2020 06:17:47 PM EEST using DSA key ID 02A76EF5
# gpg: Good signature from "Felix Fietkau <nbd@nbd.name>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7622/mt7663 chipsets rely on a fixed reverse queue map order respect
to mac80211 one:
- q(0): IEEE80211_AC_BK
- q(1): IEEE80211_AC_BE
- q(2): IEEE80211_AC_VI
- q(3): IEEE80211_AC_VO
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
acs and wmm index are swapped in mt7615_queues_acq respect to the hw
design
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Coverage class callback can potentially run in parallel with other
routines (e.g. mt7615_set_channel) that configures timing registers.
Run coverage class callback holding mt76 mutex
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7611N is basically the same as MT7615N, except it only supports 5GHz
It is used by some TP-Link and Mercury wireless routers
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76 core uses ffs() to find the next free bit. This works well for 32 bit
architectures where BITS_PER_LONG is 32. ffs only checks 32 bit values, so
allocation fails on 64 bit architectures.
Additionally, the wcid mask array was too small in cases where the array
was not a multiple of BITS_PER_LONG.
Fix this by making the wcid mask array u32 instead and use DIV_ROUND_UP
for the size, just in case we ever bump it to a value that's not a multiple
of 32.
Reported-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix a NULL pointer dereference in mt7915_register_ext_phy since phy
data structure is allocated by mt76_alloc_phy routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix hw_scan with ssid_type for specified SSID only
The definition for ssid_type in current firmware is that
ssid_type BIT(2) set actually for specified SSID + wildcard SSID.
ssid_type BIT(2) and ssid_type_ext BIT(0) both set actually for
specified SSID only;
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are some spelling mistakes in some literal strings. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
switch to per-vif ps support since mt7615 offload firmware can handle it
properly. This patch allows enabling/disabling power-save support on p2p
interface
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
drivers/net/wireless/mediatek/mt76/mt7915/main.c:694:1: sparse:
sparse: context imbalance in 'mt7915_sta_rc_update' - wrong count at exit
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:303:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:304:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:305:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:319:35: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:327:35: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:345:41: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:355:33: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: sparse: invalid assignment: |=
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: left side has type unsigned int
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: right side has type restricted __le32
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All drivers before MT7915 have a limit of 128 WCID entries. Stop relying
on ARRAY_SIZE(dev->mt76.wcid), since it no longer reflects that limit.
Fixes: 49e649c3e0 ("mt76: adjust wcid size to support new 802.11ax generation")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move assignment of .data1 and .data2 to a single place and fix overwriting
of values from the template
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable or disable OBSS PD when the bss config changes or we
assoc to an AP that broadcasts the IE.
With this patch, we can get ~20% gain in OBSS OTA environment.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76x02_mcu_msg_send is run just by mmio code so get rid of
mt76_is_mmio() check
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce remain_on_channel support to mt7615 driver if the device is
running offload firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In file included from ./include/linux/firmware.h:6:0,
from drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:4:
In function ‘__mt7915_mcu_msg_send’,
inlined from ‘mt7915_mcu_send_message’ at drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:370:6:
./include/linux/compiler.h:396:38: error: call to ‘__compiletime_assert_545’ declared with attribute error: BUILD_BUG_ON failed: cmd == MCU_EXT_CMD_EFUSE_ACCESS && mcu_txd->set_query != MCU_Q_QUERY
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
./include/linux/compiler.h:377:4: note: in definition of macro ‘__compiletime_assert’
prefix ## suffix(); \
^~~~~~
./include/linux/compiler.h:396:2: note: in expansion of macro ‘_compiletime_assert’
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^~~~~~~~~~~~~~~~~~~
./include/linux/build_bug.h:39:37: note: in expansion of macro ‘compiletime_assert’
#define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
^~~~~~~~~~~~~~~~~~
./include/linux/build_bug.h:50:2: note: in expansion of macro ‘BUILD_BUG_ON_MSG’
BUILD_BUG_ON_MSG(condition, "BUILD_BUG_ON failed: " #condition)
^~~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:280:2: note: in expansion of macro ‘BUILD_BUG_ON’
BUILD_BUG_ON(cmd == MCU_EXT_CMD_EFUSE_ACCESS &&
^~~~~~~~~~~~
BUILD_BUG_ON is meaningless here, chang it to WARN_ON.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522034533.61716-1-yuehaibing@huawei.com
Fix typo defining ps_work in mt7615_register_ext_phy(). This is not a
real issue since 802.11 power save is not yet support by the external phy
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce essential bss information for multiple vifs hw_scan in
mt7615_mcu_uni_add_dev adding the interface
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce p2p-go/p2p-client suppor to mt76 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Differentiate hw scan channel time between passive and active scan
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615_mcu_sched_scan_enable should be taken along with
mt7615_mcu_sched_scan_req to have proper scan plans initialization.
Fixes: bd39bd2f00c3 ("mt76: mt7663: introduce WoW with net detect support")
Co-developed-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Signed-off-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
make mac_work per phy instead of per device and fix a possible deadlock
in mt7915_stop since mt7915_mac_work runs holding mt76 mutex
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add debug counters to track status of beamformer and beamformee.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows to set HE TxBF runtime stream capabilities
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable TxBF modules and trigger sounding process to support Tx beamformer.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a helper to reduce duplicate codes.
This is a preliminary patch to add Tx beamforming support.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Cancel possible power_save work before stopping the mt7663u interface
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing PLE/PSE base register definitions for mt7663u
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Copy key pointer value before running mt76_tx_status_skb_add() in
mt7663u_mac_write_txwi since it will be overwritten setting
mt76_tx_cb for probing frames
Co-developed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows host driver to get useful information of some important modules.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is useful for IBSS Mesh to adjust t_clockdrift.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reported-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Driver can manually set fixed rate for each peer through debugfs.
May use .set_bitrate_mask callback and iterate stations under the
current vif to achieve the aim once it supports HE rate.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add useful debug counters since this generation uses struct rate_info
to report HE tx rate.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This generation supports much more per-peer statistics than legacy ones,
so add .sta_add_debugfs accordingly.
This is convenient to set/get more settings/counters in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mac80211 expects the definition of what HE rate info is available
inside astruct prepended to the skb.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add basic HE BSS's info for interfaces. As for the advanced features
will be added gradually in the future patches.
(i.e. BSS color, TWT, spatial reuse and OFDMA)
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Acked-by: Yiwei Chung <yiwei.chung@mediatek.com>
Acked-by: YF Luo <yf.luo@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The capabilities for the HE interfaces are generated from the capabilities
reported by the firmware.
This should move to common file once we got other HE devices support.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use firmware support for applying per-rate limit and power offsets.
This can support all HE RU types.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Acked-by: Yiwei Chung <yiwei.chung@mediatek.com>
Acked-by: YF Luo <yf.luo@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable HE rate reporting in Rx path
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for the MediaTek latest generation IEEE 802.11ax 4x4
device MT7915E, which supports concurrent dual-band operation at
both 5GHz and 2.4GHz.
Note that this patch just add basic part and will add more HE
capabilities support in the further patches.
The driver supports AP, Station, Mesh and monitor mode.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Suggested-by: Shihwei Lin <shihwei.lin@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Acked-by: Yiwei Chung <yiwei.chung@mediatek.com>
Acked-by: YF Luo <yf.luo@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The newer 802.11ax devices (i.e. MT7915E) can connect to much more
peers than previous generations.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enlarge slot to support 11ax 256 BA (256 MPDUs in an AMPDU)
Signed-off-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure the mcu to scan all available channels if mac80211 does not
provide any frequency list
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support to sched scan with randomise addr
Co-developed-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Signed-off-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce WoW with net detect support
Co-developed-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Signed-off-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix mt7663 eeprom definitions for delta tx power parsing
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615_eeprom_get_power_index can return negative error value.
Check mt7615_eeprom_get_power_index return value before using it
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If device has enabled beacon hw filter rx beacons are not reported to
the host. Introduce beacon_loss mcu event to trigger mac80211 mlme
connection state machine in this configuration.
IEEE80211_VIF_BEACON_FILTER has not set in vif flags since hw beacon
filter is not enabled yet
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add KCK and KEK offload support to mt7615 driver in order to
support GTK rekeying during PM suspend
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Signed-off-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tested on Chromebok by "echo mem to /sys/power/state" to suspend and
then waked up by keyboard keystrokes to resume system.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce the mt7615_mcu_set_hif_suspend mcu command, which is usually
used to configure the interface including PCIe, USB or SDIO to the right
state during operation suspend / resume.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for hw beacon filter if available in the firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for passive frequency scanning to mt7615_mcu_hw_scan
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For the moment offload firmware supports just one entry in the scheduled
scan plan and so it runs till it is disabled by the userspace.
Do not mark the hw scheduled scan as disabled in mt7615_scan_work
after receiving a scan result
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_check_offload_capability routine to set hw/wiphy
offload capabilities according to the running firmware
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix SSID configuration performing hw frequency scanning
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
it will print an error message by itself when
devm_platform_ioremap_resource() goes wrong. so remove the duplicate
error message.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On top of the EEPROM target power, each rate can also has a power offset.
On many devices, this power offset is used to boost the tx power of lower
rates. Take this into account when parsing rate power.
The assumption here is, that the first rate (OFDM 6M or CCK 1M) has the
highest tx power
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of useless check in mt7663_load_n9 since it is used only for
mt7663 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7663 firmware v2 is used for embedded devices since it has more completed
features in AP mode.
Add the capability to specify which firmware load first (v3 or v2)
using prefer_offload_fw kernel parameter and fallback to the other one
if the selected firmware fails to load
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently mt7663 devices do not support DBDC so fw events have no info
about it. Fix mt7615_mcu_bss_event that wrongly use bss_idx as DBDC
band_idx while it is vif index.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce sta pointer to mt7615_mcu_add_bss_info signature in order to
avoid sta lookup in mt7615_mcu_bss_basic_tlv routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
BMC entry for MT7663 unicmd firmware should be a broadcast/multicast entry,
not a unicast entry, that is GTK rekey offload would rely on.
Fixes: 138860679b ("mt76: mt7615: add more uni mcu commands")
Cc: Soul Huang <Soul.Huang@mediatek.com>
Suggested-by: YF Luo <Yf.Luo@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable mac80211 TDLS support by default. Disable TDLS hw filtering for
mt7615 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt7615_mcu_add_bss_info routine before mt7615_mcu_sta_add since
the firmware requires the bss is created before the relative sta
Tested-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: YF Luo <yf.luo@mediatek.com>
Suggested-by: Lucy Hsu <lucy.hsu@mediatek.com>
Co-developed-by: Soul Huang <soul.huang@mediatek.com>
Signed-off-by: Soul Huang <soul.huang@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A switch from one rate index to the next only happens when tx count from
the current slot is greater than MT7615_RATE_RETRY, which is 1 has to be
subtracted from count, instead of added to it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A switch from one rate index to the next only happens when tx count from
the current slot is greater than MT7615_RATE_RETRY, which is 1 has to be
subtracted from count, instead of added to it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sometimes mt7615_mac_set_timing gets called while the slot time is still
configured to 20. Ensure that in this case it always uses the OFDM CFend
rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sometimes mt7615_mac_set_timing gets called while the slot time is still
configured to 20. Ensure that in this case it always uses the OFDM CFend
rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In VHT mode we can receive larger MPDUs. Increasing the buffer size reduces
fragmentation here, which should improve performance.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The hardware requirements for A-MPDU density are entirely on the tx side,
not the rx side. Because of that, the IE value should stay at 0 and the
minimum value should instead be enforced in WTBL/TXWI
MT7615 has no restrictions here
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize tx_status_data pointer in order to enable Air Time Fairness
for mt7663u chipset
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since usb code can't access device registers in interrupt context, move
rcu_read_lock/rcu_read_unlock in mt7615_poll_tx routine. Moreover loop
over a local msta list in mt7615_mac_sta_poll since mt7663u driver will
not be able to complete the inner while loop before sta_poll_list list
is refilled by mt7615_mac_add_txs/mt7615_mac_fill_rx
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the vif is running in station mode the aid will be passed by mac80211
using bss_conf.aid. Fix aid configuration in mt7615_mcu_wtbl_generic_tlv
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Current mt7663 offload firmware can support up to 32 wtbl entries
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check the firmware-own configuration has been applied polling
MT_CONN_HIF_ON_LPCTL register
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add return code parsing for the following unified commands:
- MCU_UNI_CMD_DEV_INFO_UPDATE
- MCU_UNI_CMD_BSS_INFO_UPDATE
- MCU_UNI_CMD_STA_REC_UPDATE
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce rx-queues debugfs node in order to dump rx queues status.
This would be useful for mcu fw debugging
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make Kconfig entry obvious for MT7663E
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable 802.11 power-save support available in mt7663 firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
remove IEEE80211_HW_PS_NULLFUNC_STACK capability from mt76_phy_init
routine since 802.11 ps is not currently supported by any devices and it
will conflict with mt7663 ps fw support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For sta mode mac80211 provides aid in vif->bss_conf.aid.
In order to properly support 802.11 power-save, configure correct aid
to mcu during sta association
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing register definitions in order to enable sensitivity tuning
for mt7663 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for mt7663u 802.11ac 2x2:2 chipset to mt7615 driver.
Main difference respect to pcie code base is the usb code needs to
configure wtbl from non-atomic context
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Create mt7615-common module in order to collect shared code between usb
and mmio code. Move the following source files in mt7615-common module:
- main.c
- init.c
- mcu.c
- mac.c
- debugfs.c
- eeprom.c
- trace.c
Create the following source files for mmio only source code and move them
in mt7615e module:
- pci_init.c
- dma.c
- pci_mac.c
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
make mac_work per phy instead of per device and fix a possible deadlock
in mt7615_stop since mt7615_mac_work runs holding mt76 mutex
Fixes: fdd2e57076 ("mt76: mt7615: add dual-phy support for mac80211 ops")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sparse report warnings at mt76_tx_status_unlock() and mt76_tx_status_lock()
warning: context imbalance in mt76_tx_status_lock() - wrong count at exit
warning: context imbalance in mt76_tx_status_unlock() - unexpected unlock
The root cause is the additional __acquire(&dev->status_list.lock)
and __release(&dev->status_list.unlock) called
from inside mt76_tx_status_lock() and mt76_tx_status_unlock().
Remove __acquire(&dev->status_list.lock) annotation
Remove __releases(&dev->status_list.unlock)
Correct &dev->status_list.unlock to &dev->status_list.lock
-unlock not defined in the sk_buff_head struct
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable MSI/MSI-X PCI interrupts by default. This patch has been tested
using Banana Pi r64 board
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With MSI interrupts, IRQs must not be enabled from within the IRQ handler,
because that can lead to lost events.
Defer IRQ processing to a tasklet, which is also responsible for enabling
IRQs (to avoid race conditions against the handler)
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Soul Huang <soul.huang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix DMA unmap length estimation in mt7615_txp_skb_unmap_hw for mt7622
chipset
Fixes: 6aa4ed7927 ("mt76: mt7615: implement DMA support for MT7622")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Avoid having to attempt hw scan and fall back to software for every scan
on devices/firmware without hw scan support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check that val is not zero before aggr_per estimation in order to avoid a
possible division by 0
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the EEPROM data is read from flash, it can contain tx DPD calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the EEPROM data is read from flash, it can contain DC offset calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The function “platform_get_irq” can log an error already.
Thus omit a redundant message for the exception handling in the
calling function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mac80211/hostapd runs mt7615_set_channel with the same channel
parameters sending multiple rdd commands overwriting the previous ones.
This behaviour is causing tpt issues on dfs channels.
Fix the issue checking new channel freq/width with the running one.
Fixes: 5dabdf71e9 ("mt76: mt7615: add multiple wiphy support to the dfs support code")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rom patch is shared between Bluetooth and Wifi devices, so correct the
naming to allow two drivers to share the same file.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce address parameter to mt7615_eeprom_init routine in order to be
reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Generalize mt7615_rate_desc introducing mt7615_wtbl_desc and
mt7615_key_desc data structures in order to configure the hw wtbl
in a non-atomic context for usb devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove key dependency from mt7615_mac_wtbl_update_key and export
mt7615_mac_wtbl_update_key, mt7615_mac_wtbl_update_pk and
mt7615_mac_wtbl_update_cipher in order to reuse them in usb code.
Move mt7615_mac_get_cipher in mac.h
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7615_mac_wtbl_addr in mac.h and add inline qualifier in order to
be reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce __mt7663_load_firmware routine to load firmware for usb
devices.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move register configuration out of mt7615_mac_set_rates since usb
driver can't access device register in interrupt context. Introduce
mt7615_mac_update_rate_desc routine to report rate info to
mt7615_mac_set_rates
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend mt7615_write_txwi routine to support usb txwi configuration
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce headroom and tailroom to mt76_mcu_ops data structure in order
to unify the routine used for mcu message allocation. This is a
preliminary patch to add mt7663u support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76_wr(dev, MT_CSR(0x010), 0x8208) that would cause
MT_PCIE_IRQ_ENABLE to be disabled; MT_PCIE_IRQ_ENABLE should always keep
on enabled when the driver is running.
0x44064 is a not existing address
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce rlm tlv header in bss_info mcu command in order to
inform the mcu about operating channel. Rlm header is necessary only if
the mcu is running low power functionalities (e.g offloaded scan)
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce BSS absence event that is reported when the fw
is leaving or entering current operational channel.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce scheduled scan support for mt7663e devices
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce hw scan support to mt7663e driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Keep Rx filters default value if the firmware supports offload and
low power features.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_set_channel_domain routines in order to instruct
the mcu about supported band/channels. This is a preliminary patch to
add hw scan support to mt7663e driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable dfs RDD mcu commands for mt7663 driver since they are not
currently supported by the 7663 firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make scs configurable per phy since most of the chipsets do not
support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable Noise floor estimation for mt7663 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Simplify mib macros and use proper type for related counters.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7610 PCI id found on D-Link DWR-960 to pci_device_id table.
Run-tested on D-Link DWR-960 with no-name half-size mPCIE card
with mt7610e.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce Mercury UD13 dual-band dongle support to mt76x2u driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The current version has a new USB ID and reports as an 0x7632 device.
Adding the IDs results in it working out of the box.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If a MCU timeout occurs before a hw restart completes, another hw restart
is scheduled, and the station state gets corrupted.
To speed up dealing with that, do not issue any MCU commands after the first
timeout, and defer handling timeouts until the reset has completed.
Also ignore errors in MCU commands during start/config to avoid making user
space fail on this condition. If it happens, another restart is scheduled
quickly, and that usually recovers the hardware properly.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Second set of patches for v5.7. Lots of cleanup patches this time, but
of course various new features as well fixes.
When merging with wireless-drivers this pull request has a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve that just drop the changes from commit cf52c8a776 in
wireless-drivers and take the hunk from wireless-drivers-next as is.
The list of specific subsystem device IDs are not necessary after
commit d6f2134a38 (in wireless-drivers-next) anymore, the detection
is based on other characteristics of the devices.
Major changes:
qtnfmac
* support WPA3 SAE and OWE in AP mode
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
mt76
* MT7663 support for the MT7615 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeechaAAoJEG4XJFUm622b/IcH/jzdxSwI/dRp2ZrEG+UFDNyZ
ChTdgW1k+WWLrTKaw5S+mmtM9sLQ7Ia5dL+ZyE7tFIEGzuCSdAbbOIkygw+rhLy9
BO0rsTbXRuErRpUJgwKc56sFrvBL2pm4Rx+4IV29jhXdyJ70MUvRAINcHLESeBcO
uI5dqapScRf/EnVYP2Zso6i2FLep5hoC0reBq2UQ5Y95Lv0cpMCbHQ1xqdcm9pI3
ZvLDpVyGpp75Eoxlt1Ubiv6ijsEnTaM3cI+Q5rRWt8g3JKP7yYT7HGbJ3fb0cWhq
bNNISs+XN67lnyU1Mx3c2pjyb+szJZ0o4OGbYNAqsquItl4B0RQc3fUBMlCUlYI=
=+2Hj
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
Second set of patches for v5.7. Lots of cleanup patches this time, but
of course various new features as well fixes.
When merging with wireless-drivers this pull request has a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve that just drop the changes from commit cf52c8a776 in
wireless-drivers and take the hunk from wireless-drivers-next as is.
The list of specific subsystem device IDs are not necessary after
commit d6f2134a38 (in wireless-drivers-next) anymore, the detection
is based on other characteristics of the devices.
Major changes:
qtnfmac
* support WPA3 SAE and OWE in AP mode
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
mt76
* MT7663 support for the MT7615 driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce support for mt7663e 802.11ac 2x2:2 chipset to mt7615 driver.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_uni_set_ba routine in order to add support
for mt7663e driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_uni_set_bss, mt7615_mcu_uni_set_dev and
mt7615_mcu_uni_set_beacon_offload uni mcu commands. This is a
preliminary patch to add mt7663e support
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_uni_set_bmc and mt7615_mcu_uni_set_sta routines for
mt7663e commands.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mcu uni command type. Uni commands rely on a stripped verions
of mt7615_mcu_txd data strutture. Split mt7615_mcu_txd_common and
mt7615_mcu_txd. Uni commands will be use by mt7663e driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_init_mac_chain routine to configure per band mac
register since new devices (e.g. mt7663e) do not support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_eeprom_parse_hw_band_cap routine in order to configure
supported band for mt7663e and mt7622 devices since they do not rely on
eeprom data to enable 2GHz/5GHz bands
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend mt7615_mcu_set_eeprom routine in order to be reused
adding mt7663e support to mt7615 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend mt7615_driver_own and mt7615_firmware_own in order to reuse
them adding mt7663e support to mt7615 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7663e support to mt7615_reg_map routine in order to reuse it
adding support for mt7663e driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reuse mt7615 code adding support for mt7663e driver,
introduce mt7615e_reg_map since mt7663e and mt7615 rely on a
different base registers definitions.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently fw commands rely on negative cmds since they need different
mcu msg metadata. Extend this approach introducing MCU_FW_PREFIX.
This is a preliminary patch to support new mt7663e firmware commands
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7615_mcu_set_beacon_offload, mt7615_mcu_set_dev and
mt7615_mcu_set_bss routine in mt7615_mcu_ops data structure.
This is a preliminary patch to support mt7663 firmware
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Simplify mt7615_mcu_set_bss_info relying on mcu tlv helpers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on skb API and avoid kmalloc the buffer in mt7615_mcu_set_eeprom
routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7615_mcu_set_sta for fw version 1 and version 2 in mt7615_mcu_ops
data structure. This is a preliminary patch to properly support mt7663e
firmware.
Rework utility routines to rely on skb APIs for msg parsing
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7615_mcu_set_bmc for fw version 1 and version 2 in
mt7615_mcu_ops data structure. This is a preliminary patch
to properly support mt7663e firmware.
Rework utility routines to rely on skb APIs for msg parsing
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_ops data structure in order to support multiple
mcu ops API.
Move mt7615_mcu_set_{tx,rx}_ba to mt7615_mcu_ops differentiating between
fw v1 and v2. This is a preliminary patch to properly support mt7663e
firmware.
Rework utility routines to rely on skb APIs for msg parsing
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_send_message routine in order to allocate mcu skb
out of mcu sending routine. This approach is useful when the mcu
message is complicated and it is convenient to rely on skb buffer API
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Always initialize to 0 mcu messages since if they are not propely
configured they could hang the firmware.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7615_init_device routine in order to be reused adding support for
mt7663 in mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reuse mt7615_mcu_send_firmware routine adding support for
usb devices, clean fw hw queue just for mmio devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_wait_response in order to be reused parsing mt7663u
mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_fill_msg routine to initialize mcu messages.
mt7615_mcu_fill_msg will be reused adding mt7663u support
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/mediatek/mt76/mt76x0/phy.c: In function mt76x0_phy_rf_init:
drivers/net/wireless/mediatek/mt76/mt76x0/phy.c:1158:5: warning: variable val set but not used [-Wunused-but-set-variable]
Fixes: 10de7a8b4a ("mt76x0: phy files")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This if statement was supposed to be deleted, but it wasn't. It means
that we sometimes don't set the sensitivity correctly.
Fixes: 2cad515ece ("mt76: mt7615: add missing settings for simultaneous dual-band support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When injecting beacon frames via monitor interface, they must not be sent to
the beacon hardware queue, because they don't follow normal hardware beacon tx
rules.
Fix sending them by adding a flag to mt7615_mac_write_txwi that selects the
beacon queue for tx, and use it only from mt7615_mcu_set_bcn.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the minimum power is raised too much, it can make it impossible for weaker
clients to connect, and there are some scenarios where the false detects will
not go down no matter how much the sensitivity is adjusted.
Fixes connectivity issues in some rare cases
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove usb workqueue if mt76u_set_endpoints fails.
Fixes: 284efb473e ("mt76: mt76u: rely on a dedicated stats workqueue")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Loop over all possible hw rx queues in mt76u_rx_tasklet since new
devices will report mcu events through mcu hw queue
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the hardware receives an oversized packet with too many rx fragments,
skb_shinfo(skb)->frags can overflow and corrupt memory of adjacent pages.
This becomes especially visible if it corrupts the freelist pointer of
a slab page.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce mt76_mcu data structure to contain common fields between
mt76u_mcu and mt76e_mcu.
Initialize mcu common fields in mt76_alloc_device().
Rely on mt76_mcu in mt76_mcu_rx_event and in mt76_mcu_get_response
in order to reuse them in usb code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of rx_mask in mt7615_eeprom_parse_hw_cap routine since it is not
actually used
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rename usb stat_wq in wq in order to be reused not just for gathering hw
tx statistics
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set RX scatter gather number to 4 in order to extend the maximum AMSDU
size to 11,454.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As previous devices, mt7622 relies on multiple hw queues while for
mt7615 we have just on per band hw queue and the mcu demux the traffic
according to the packet AC. In order to dump all configured hw queues,
rely on mt76_queues_read for mt7622 in mt7615 debugfs
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Overwriting the RMAC_CHFREQ register is not reliable enough, as the firmware
could potentially write it again.
Since there is no PHY index indication in the rx info, we need to use another
way:
If both PHYs are using different channels, find the PHY where chfreq matches
the register value.
The only corner case remaining is when both PHYs are using the same channel.
In that case, the per-packet noise value on the primary PHY will have
information belonging to the chains of the secondary PHY from the previous
received packet of that PHY. The secondary PHY will set noise to 0 for extra
chains.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify code converting between the different txpower values. Always add/remove
the combined txpower delta before dividing half-dB values.
Also fix the combined txpower delta values. The correct half-dB delta for
3 chains is 9, not 8.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not set the tx/rx start bits in MT_MAC_SYS_CTRL from within initvals.
The driver sets these later when the hardware is ready
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The second PHY receives no packets unless there is an active vif present.
Set the WANT_MONITOR_VIF flag to deal with that
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To adapt new firmware version.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To adapt new firmware version.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reduce command/event times, newer firmware adds a tag
sta_rec_wtbl to take care of WTBL operations.
MCU_EXT_CMD_WTBL_UPDATE is deprecated.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add fw_ver in mt7615_dev to check firmware version, and adjust
mt7615_mcu_send_sta_rec() to adapt firmware v2 changes.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Operating command is simpler and just as clear
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu_add_wtbl and mcu_set_ht_cap into mcu_set_sta to simplify flow.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move set_bmc_wtbl into sta_rec function to simplify flow.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the firmware detects a problem, it needs the host to stop/reset DMA and
resume it again when the hardware state has been reset.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Setting the tx power by manipulating EEPROM may in some cases not be enough,
since it only covers the base target power and not per-rate offsets.
In other cases, it could limit tx power of rates too much, possibly reducing
throughput or range.
Use firmware support for applying per-rate limit and power offsets for
different values of Nss.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7622 does not have the CR4 microcontroller sitting in the data path.
Because of that, it uses the chip's native tx descriptor format instead of
something parsed and converted by the firmware.
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
MT7622 does not have a CR4 microcontroller, so it only uses its own N9
firmware.
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When sending EEPROM data to the MCU, MT7622 uses a longer buffer
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7622 queue mapping is different from MT7615 and requires an extra dma
scheduler init and a few register tweaks
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7622 uses more interrupt bits for queue tx completion events.
Enabling those extra bits is harmless on MT7615
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The beginning of the struct is guaranteed to be 4-byte aligned, and this
attribute allows the compiler to generate more efficient code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ring is used for looping back tx powersave filtered frames, so it could
use some more room, in case more than one aggregate was queued
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes a theoretical issue where it could potentially overwrite an existing
descriptor entry (and leaking its skb)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Avoids a theoretical corner case where the hardware could try to process
a stale descriptor after a watchdog reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Define MT_DRV_RX_DMA_HDR flag in drv_flag in order to not skip rx frame
dma header since new devices (e.g. mt7663u) reports rx frame info in the
usb dma header
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to support mt7663u usb dongles
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76u_skb_dma_info utility routine in mt76-usb module in order
to be reused adding mt7663u support
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
7663u devices rely on a different endpoint mapping. Take it into account
in mt76u_alloc_tx routine
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce extended utility routines to read/write data o usb bus. New
devices (e.g. mt7663u) will rely on both upper and lower part of the
register address. Add ext parameter to mt76u_init signature in order to
reuse the code adding mt7663u support.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76u_alloc_mcu_queue utility routine to allocate mcu hw rx queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Resume all possible rx queues after suspend. This is a preliminary patch
to support mt7663u devices
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76_queue parameter to mt76u_rx_urb_alloc signature since this
routine will be used to allocate urbs for mcu hw queue used by new
chipset generation (e.g. mt7663u). Check sg_max_size in in
mt76u_urb_alloc in order to use linear urb for mcu queue
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76u_alloc_rx_queue routine to allocate rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stop/free all configured rx queues (data/mcu) in
mt76u_stop_rx/mt76u_free_rx. This is a preliminary patch to support new
devices (e.g. mt7663u) that rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76u_free_rx_queue utility routine to free rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu buffer allocation in mt76x2u/mt76x0u drivers since newer
chipsets (e.g. mt7663u) does not rely on synchronous mcu communication
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add queue_id parameter to mt76u_submit_rx_buffers in order to reuse it
adding mt7663u support
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reuse mt76u_complete_rx for both data and mcu rx queue, rely
on mt76_queue as urb context in mt76u_complete_rx. Moreover set usb rx
endoint according to rx queue in mt76u_submit_rx_buf. This is a
preliminary patch to add mt7663u support
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_queue parameter to mt76u_refill_rx signature in order to
reuse it for mcu hw rx queue
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_queue pointer in mt76u_get_next_rx_entry in order to add
support for new devices (e.g 7663u) that reports fw events through hw rx
mcu queue
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76u_process_rx_queue routine to process rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
New devices (e.g. mt7663u) do not rely on stats workqueue to load tx
statistics but will be reported by the firmware. Check tx_status_data
pointer in mt76u_tx_tasklet in order to reuse tx tasklet for new devices
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Starting from 'commit ee8040139ab1 ("mt76: do not overwrite
max_tx_fragments if it has been set")' we can avoid overwriting
max_tx_fragments for mt76x02u devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move WIPHY_FLAG_HAS_CHANNEL_SWITCH in mt76-core module since now all
drivers support Channel Switch Announcement
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce dfs radar pattern specs in mt7615 driver in order to make
dfs debugging easier. Radar pulse/pattern thresholds are taken from
vendor SDK.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce token tracing support in mt7615_mac_tx_free routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mac_txdone tracepoint in common code in order to
be reused by mt7603 and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move dev_irq tracepoint in common code in order to be reused by mt7603
and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a set_antenna callback to setup per phy tx/rx streams.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
No need to send both MCU_EXT_CMD_SET_RX_PATH and MCU_EXT_CMD_CHANNEL_SWITCH
together to MCU.
Split them out by passing the proper command in the corresponding flow.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7615 supports dual-wiphy which means that it can run on 2.4G and 5GHz
channels simultaneously, and driver should configure each band.
Add missing register settings, and refine band related definitions to
avoid duplicate codes.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following compilation warning in mt76_eeprom_override routine
when CONFIG_OF is not set and label 'out' is not actually used
drivers/net/wireless/mediatek/mt76/eeprom.c: In function ‘mt76_eeprom_override’:
drivers/net/wireless/mediatek/mt76/eeprom.c💯1: warning: label ‘out’ defined but not used [-Wunused-label]
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on FIELD_PREP macro for led register definitions and
remove open coding
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on FIELD_PREP macro for led register definitions and
remove open coding
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize brightness_set and blink_set callbacks to
mt7615_led_set_brightness and mt7615_led_set_blink in order to enable
LED support in mt7615 driver
Tested-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During the cleanup of the aggregation session, a rx handler (or release timer)
on another CPU might still hold a pointer to the reorder buffer and could
attempt to release some packets.
Clearing pointers during cleanup avoids a theoretical use-after-free bug here.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Before extracting the tid out of the packet, check if it was qos-data.
Only accept tid values 0-7
Also, avoid accepting the hardware queue as skb queue mapping, it could
lead to an overrun. Instead, derive the hardware queue from the tid number,
in order to avoid issues with packets being filtered multiple times.
This also fixes a mismatch between hardware and software queue indexes.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
