Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Third set of patches for v5.10. Lots of iwlwifi patches this time, but
also few patches ath11k and of course smaller changes to other
drivers.
Major changes:
rtw88
* properly recover from firmware crashes on 8822c
* dump firmware crash log
iwlwifi
* protected Target Wake Time (TWT) implementation
* support disabling 5.8GHz channels via ACPI
* support VHT extended NSS capability
* enable Target Wake Time (TWT) by default
ath11k
* improvements to QCA6390 PCI support to make it more usable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
brcmf_fweh_process_event() uses in_interrupt() to select the allocation
mode GFP_KERNEL/GFP_ATOMIC. Aside of the above reasons this check is
incomplete as it cannot detect contexts which just have preemption or
interrupts disabled.
All callchains leading to brcmf_fweh_process_event() can clearly identify
the calling context. Convey a 'gfp' argument through the callchains and let
the callers hand in the appropriate GFP mode.
This has also the advantage that any change of execution context or
preemption/interrupt state in these callchains will be detected by the
memory allocator for all GFP_KERNEL allocations.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcrmgf_netif_rx() uses in_interrupt to chose between netif_rx() and
netif_rx_ni(). in_interrupt() usage in drivers is phased out.
Convey the execution mode via an 'inirq' argument through the various
callchains leading to brcmf_netif_rx():
brcmf_pcie_isr_thread() <- Task context
brcmf_proto_msgbuf_rx_trigger()
brcmf_msgbuf_process_rx()
brcmf_msgbuf_process_msgtype()
brcmf_msgbuf_process_rx_complete()
brcmf_netif_mon_rx()
brcmf_netif_rx(isirq = false)
brcmf_netif_rx(isirq = false)
brcmf_sdio_readframes() <- Task context sdio_claim_host() might sleep
brcmf_rx_frame(isirq = false)
brcmf_sdio_rxglom() <- Task context sdio_claim_host() might sleep
brcmf_rx_frame(isirq = false)
brcmf_usb_rx_complete() <- Interrupt context
brcmf_rx_frame(isirq = true)
brcmf_rx_frame()
brcmf_proto_rxreorder()
brcmf_proto_bcdc_rxreorder()
brcmf_fws_rxreorder()
brcmf_netif_rx()
brcmf_netif_rx()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
brcmf_sdio_isr() is using in_interrupt() to distinguish if it is called
from a interrupt service routine or from a worker thread.
Passing such information from the calling context is preferred and
requested by Linus, so add an argument `in_isr' to brcmf_sdio_isr() and let
the callers pass the information about the calling context.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Second set of patches for v5.10. Biggest change here is wcn3680
support to wcn36xx driver, otherwise smaller features. And naturally
the usual fixes and cleanups.
Major changes:
brcmfmac
* support 4-way handshake offloading for WPA/WPA2-PSK in AP mode
* support SAE authentication offload in AP mode
mt76
* mt7663 runtime power management improvements
* mt7915 A-MSDU offload
wcn36xx
* add support wcn3680 Wi-Fi 5 devices
ath11k
* spectral scan support for ipq6018
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting F2 block size to 128 bytes for BCM4329 allows to significantly
improve RX throughput on NVIDIA Tegra20. Before this change the throughput
was capped to 30 Mbit/s on Tegra, now throughput is at 40 Mbit/s, which is
a maximum throughput for the BCM4329 chip. The F2 block size is borrowed
from the downstream BCMDHD driver. The comment in the BCMDHD driver says
that 128B improves throughput and turns out that it works for the brcmfmac
as well.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-4-digetx@gmail.com
This patch fixes SDHCI CRC errors during of RX throughput testing on
BCM4329 chip if SDIO BUS is clocked above 25MHz. In particular the
checksum problem is observed on NVIDIA Tegra20 SoCs. The good watermark
value is borrowed from downstream BCMDHD driver and it's matching to the
value that is already used for the BCM4339 chip, hence let's re-use it
for BCM4329.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-2-digetx@gmail.com
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:16:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_spurwar_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:19036:6: warning: variable ‘tempval’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_tempsense_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:21983:28: warning: variable ‘RfctrlMiscReg6_save’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_rssi_compute_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:22986:6: warning: variable ‘phyRx0_l’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_runsamples_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23101:6: warning: variable ‘lpf_bw_ctl_miscreg4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23100:50: warning: variable ‘lpf_bw_ctl_miscreg3’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_iqcal_gainparams_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23406:6: warning: variable ‘idx’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_a2_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:24707:7: warning: variable ‘phy_a6’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_a3_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:24999:7: warning: variable ‘phy_a11’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-29-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:11:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_rx_iq_cal’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1366:29: warning: variable ‘RFOverride0_old’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_radio_2064_channel_tune_4313’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:21: warning: variable ‘qFvco’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:14: warning: variable ‘qFref’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:6: warning: variable ‘qFxtal’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_idle_tssi_est’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:2856:6: warning: variable ‘idleTssi’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_tx_iqlo_soft_cal_full’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:53: warning: variable ‘locc4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:46: warning: variable ‘locc3’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:39: warning: variable ‘locc2’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:32: warning: variable ‘iqcc0’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_periodic_cal’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4196:6: warning: variable ‘rx_iqcomp_sz’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4195:33: warning: variable ‘rx_iqcomp’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4194:16: warning: variable ‘full_cal’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_phy_txpwr_srom_read_lcnphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4919:7: warning: variable ‘opo’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-28-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'name' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'requested_packet' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'suppr_transit_count' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'send_tim_signal' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'traffic_pending_bmp' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'traffic_lastreported_bmp' not described in 'brcmf_fws_mac_descriptor'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-14-lee.jones@linaro.org
The function headers are either very weakly documented or not at all.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:94: warning: Function parameter or member 'reg50' not described in 'brcmf_btcoex_info'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:94: warning: Function parameter or member 'saved_regs_part2' not described in 'brcmf_btcoex_info'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:233: warning: Function parameter or member 'btci' not described in 'btcmf_btcoex_save_part1'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:253: warning: Function parameter or member 'btci' not described in 'brcmf_btcoex_restore_part1'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:273: warning: Function parameter or member 't' not described in 'brcmf_btcoex_timerfunc'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Function parameter or member 'vif' not described in 'brcmf_btcoex_set_mode'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Function parameter or member 'duration' not described in 'brcmf_btcoex_set_mode'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Excess function parameter 'cfg' description in 'brcmf_btcoex_set_mode'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-17-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:27:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_dotxstatus’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:845:6: warning: variable ‘mcl’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_b_phy_reset’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:1779:7: warning: variable ‘phy_in_reset’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_ucode_download’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:2273:23: warning: variable ‘wlc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_b_coreinit’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3176:6: warning: variable ‘sflags’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_set_chanspec’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3902:7: warning: variable ‘switchband’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_down’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5182:7: warning: variable ‘dev_gone’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_ofdm_rateset_war’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5393:5: warning: variable ‘r’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘mac80211_wlc_set_nrate’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5876:6: warning: variable ‘bcmerror’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_d11hdrs_mac80211’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:6213:7: warning: variable ‘short_preamble’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-10-lee.jones@linaro.org
Some formatting issues, some missing and some extra descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:162: warning: Function parameter or member 'oui' not described in 'brcmf_p2p_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:162: warning: Function parameter or member 'elts' not described in 'brcmf_p2p_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:181: warning: Function parameter or member 'oui' not described in 'brcmf_p2p_action_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:181: warning: Function parameter or member 'elts' not described in 'brcmf_p2p_action_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:196: warning: Function parameter or member 'query_data' not described in 'brcmf_p2psd_gas_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:210: warning: Function parameter or member 'extra_listen' not described in 'brcmf_config_af_params'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Function parameter or member 'ifp' not described in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Excess function parameter 'ndev' description in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Excess function parameter 'action' description in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'wdev' not described in 'brcmf_p2p_remain_on_channel'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'cookie' not described in 'brcmf_p2p_remain_on_channel'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1063: warning: Function parameter or member 'channel' not described in 'brcmf_p2p_act_frm_search'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1337: warning: Function parameter or member 'mac' not described in 'brcmf_p2p_gon_req_collision'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Function parameter or member 'cfg' not described in 'brcmf_p2p_ifchange'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Function parameter or member 'if_type' not described in 'brcmf_p2p_ifchange'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Excess function parameter 'mac' description in 'brcmf_p2p_ifchange'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-6-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:18:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_finalize’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:648:25: warning: variable ‘sgi’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus_complete’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:856:18: warning: variable ‘rr_retry_limit’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:855:5: warning: variable ‘antselid’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:853:41: warning: variable ‘tx_error’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:853:7: warning: variable ‘update_rate’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1037:28: warning: variable ‘tx_info’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1035:28: warning: variable ‘ini’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-5-lee.jones@linaro.org
