wil6210 supports channels 1-3 of the 60GHz band.
New FW added support for channel 4. Add support for channel 4 also in
wil6210 driver.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reset file is not used and may cause race conditions
with operational driver if used.
Signed-off-by: Karthick Gopalasubramanian <kargop@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove extra parentheses to fix the clang warning of extraneous
parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Array firstep_table is being assigned but is never used
hence it is redundant and can be removed.
Cleans up clang warning:
warning: 'firstep_table' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove extra parentheses to fix the clang warning of extraneous
parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 has the MAC_PCU_ADDR1 configured properly
and hence it will not send spurious ack frames
during boot up.
Hence the reset_rx_filter workaround is not needed
for WCN3990. Add a hw_param to indicate if hardware rx
filter reset is needed and skip the reset_rx_filter for
WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current support in the 60GHz band is for channels 1-4.
Add support for channels 5 and 6.
This requires enlarging ieee80211_channel.center_freq from u16 to u32.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When continuously running wifi up/down sequence, the napi poll
can be scheduled after the CE buffers being freed by ath10k_pci_flush
Steps:
In a certain condition, during wifi down below scenario might occur.
ath10k_stop->ath10k_hif_stop->napi_schedule->ath10k_pci_flush->napi_poll(napi_synchronize).
In the above scenario, CE buffer entries will be freed up and become NULL in
ath10k_pci_flush. And the napi_poll has been invoked after the flush process
and it will try to get the skb from the CE buffer entry and perform some action on that.
Since the CE buffer already cleaned by pci flush this action will create NULL
pointer dereference and trigger below kernel panic.
Unable to handle kernel NULL pointer dereference at virtual address 0000005c
PC is at ath10k_pci_htt_rx_cb+0x64/0x3ec [ath10k_pci]
ath10k_pci_htt_rx_cb [ath10k_pci]
ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci]
ath10k_ce_per_engine_service [ath10k_pci]
ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci]
ath10k_ce_per_engine_service_any [ath10k_pci]
ath10k_pci_napi_poll+0x48/0xec [ath10k_pci]
ath10k_pci_napi_poll [ath10k_pci]
net_rx_action+0xac/0x160
net_rx_action
__do_softirq+0xdc/0x208
__do_softirq
irq_exit+0x84/0xe0
irq_exit
__handle_domain_irq+0x80/0xa0
__handle_domain_irq
gic_handle_irq+0x38/0x5c
gic_handle_irq
__irq_usr+0x44/0x60
Tested on QCA4019 and firmware version 10.4.3.2.1.1-00010
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
-----BEGIN PGP SIGNATURE-----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=2Dmn
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a
device below it (Myron Stowe)
- Simplify SHPC existence/permission checks (Bjorn Helgaas)
- Remove hotplug sample skeleton driver (Lukas Wunner)
- Convert pciehp to threaded IRQ handling (Lukas Wunner)
- Improve pciehp tolerance of missed events and initially unstable
links (Lukas Wunner)
- Clear spurious pciehp events on resume (Lukas Wunner)
- Add pciehp runtime PM support, including for Thunderbolt controllers
(Lukas Wunner)
- Support interrupts from pciehp bridges in D3hot (Lukas Wunner)
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph
Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is
supplied (Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum
(Jakub Kicinski)
- Set IRQCHIP_ONESHOT_SAFE for PCI MSI irqchips (Heiner Kallweit)
- Document ACPI description of PCI host bridges (Bjorn Helgaas)
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
- To avoid bus errors, enable PASID only if entire path supports
End-End TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD
Controller (Bjorn Helgaas)
- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
- Remove Aardvark outbound window configuration (Evan Wang)
- Fix Aardvark bridge window sizing issue (Zachary Zhang)
- Convert Aardvark to use pci_host_probe() to reduce code duplication
(Thomas Petazzoni)
- Correct the Cadence cdns_pcie_writel() signature (Alan Douglas)
- Add Cadence support for optional generic PHYs (Alan Douglas)
- Add Cadence power management ops (Alan Douglas)
- Remove redundant variable from Cadence driver (Colin Ian King)
- Add Kirin MSI support (Xiaowei Song)
- Drop unnecessary root_bus_nr setting from exynos, imx6, keystone,
armada8k, artpec6, designware-plat, histb, qcom, spear13xx (Shawn
Guo)
- Move link notification settings from DesignWare core to individual
drivers (Gustavo Pimentel)
- Add endpoint library MSI-X interfaces (Gustavo Pimentel)
- Correct signature of endpoint library IRQ interfaces (Gustavo
Pimentel)
- Add DesignWare endpoint library MSI-X callbacks (Gustavo Pimentel)
- Add endpoint library MSI-X test support (Gustavo Pimentel)
- Remove unnecessary GFP_ATOMIC from Hyper-V "new child" allocation
(Jia-Ju Bai)
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect
(Ray Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
- Fix mobiveil iomem/phys_addr_t type usage (Lorenzo Pieralisi)
- Fix mobiveil missing include file (Lorenzo Pieralisi)
- Add mobiveil Kconfig/Makefile support (Lorenzo Pieralisi)
- Fix mvebu I/O space remapping issues (Thomas Petazzoni)
- Use generic pci_host_bridge in mvebu instead of ARM-specific API
(Thomas Petazzoni)
- Whitelist VMD devices with fast interrupt handlers to avoid sharing
vectors with slow handlers (Keith Busch)
* tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (153 commits)
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI: Limit config space size for Netronome NFP5000
PCI/MSI: Set IRQCHIP_ONESHOT_SAFE for PCI-MSI irqchips
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Check for PCIe Link downtraining
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: mvebu: Drop bogus comment above mvebu_pcie_map_registers()
...
The ath9k driver doesn't need anything provided by pci-aspm.h, so remove
the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
HW requires Rx buffers to be 4 bytes aligned. Modify the driver to
meet this requirement.
Enable OFU rdy valid bug fix, to prevent hang in oful34_rx while
there is back-pressure from host during RX.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver doesn't support secured boot flow, hence
prevent FW download in case HW is configured for such a flow.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently wil6210 ignores the channel field in the
cfg80211_mgmt_tx_params struct for wil_cfg80211_ops mgmt_tx operation
and sends all management frames on the serving channel.
Add support for off-channel transmission of management frames
(WIPHY_FLAG_OFFCHAN_TX) in AP mode. This is useful in enterprise APs
for sending custom probe request frames.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Single MSI is the current default configuration.
With multiple MSI interrupts configuration, Tx/Rx processing could
run in parallel on different CPU cores and allow better balance
between the cores.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW file name for Talyn device can be different from the default name.
In such a case use a corresponding board file name.
If such a board file is not present FW download procedure will fail.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware ready event may take longer than
current timeout in some scenarios, for example
with multiple RFs connected where each
requires an initial calibration.
Increase the timeout to support these scenarios.
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW can support BACK window size 64 for performance improvements.
A new FW capability is added for notifying the host on the increased
max BACK win size support.
Defining WIL_MAX_AGG_WSIZE_64 and WIL_MAX_AMPDU_SIZE_128 to be used
in this case.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Scan is allowed only on client interfaces (STA/P2P).
Allow scan on AP interface so that the AP can discover rouge
or unauthorized neighbor APs.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver can request FW to report link statistics using
WMI_LINK_STATS_CMDID.
FW will report statistics with WMI_LINK_STATS_EVENTID.
Two categories of statistics defined: basic and global.
New "link_stats" debugfs is used for requesting basic statistics
report (write) and for reading the basic statistics (read).
"link_stats_global" debugfs is used for requesting and reading the
global statistics.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With some tool chains compilation fails due to type
mismatch of the arguments passed to min().
Use min_t() to solve these compilation errors.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extend MSI support to 3-MSI in order to load balance the tx\rx
interrupts between different cores.
use_msi module parameter has changed to n_msi. Usage:
- Set n_msi to 0 for using INTx
- Set n_msi to 1 for using single MSI
- Set n_msi to 3 for using 3-MSI
In 3-MSI configuration MSI 0 is used for TX interrupts, MSI 1
is used for RX interrupts and MSI 2 is used for MISC interrupts.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW file name for Talyn device is different from the default name.
This patch searches for Talyn specific FW file name and fallback
to the default FW file in case it is not present.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver sets CHECKSUM_UNNECESSARY only in case the HW
doesn't report checksum error.
As ip_summed value is not initialized it is not clear what
the driver will report to the network stack in case of HW checksum
error or in case HW doesn't calculate checksum.
Initialize ip_summed to CHECKSUM_NONE to guarantee checksum
calculation by the network stack in the above cases.
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For negative temperatures, "temp" debugfs is showing wrong values.
Use signed types so proper calculations is done for sub zero
temperatures.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Collect statistics of TX latency. The latency is measured from the time
the HW gets aware of new SKB to transmit until the HW indicates tx
complete for this SKB.
The statistics are shown via new "tx_latency" debugfs.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to recent change in FW, driver will be notified of corrupted Rx
packets (e.g. MIC error).
Drop such packets before they are delivered to network stack.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Store the last received multicast sequence number (SN) part of the TID
info. Drop Rx multicast packets with retry bit set which their SN
is equal to the last received.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The flag needs to be cleared for the last packet in the list, not the
first one. Fixes some issues with multicast packet loss for powersave
clients connected to an ath9k AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lower limits than the CTLs
of the user configured regdomain.
To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ensure that a buffer gets tracked as part of the block-ack window as
soon as it's dequeued from the tid for the first time. Ensure that
double calls to ath_tx_addto_baw (e.g. on retransmission) don't cause
any issues.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes missed indications of end of U-APSD service period to mac80211
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The checks already prevents periodic cal from being started while noise
floor calibration runs. It is missing checks for the other way around.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9002 code and the QCA AR9003+ reference code do the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath6kl_bmi_init() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The QCA4019 hw1.0 firmware 10.4-3.2.1-00050 and 10.4-3.5.3-00053 (and most
likely all other) seem to ignore the WMI_CHAN_FLAG_DFS flag during the
scan. This results in transmission (probe requests) on channels which are
not "available" for transmissions.
Since the firmware is closed source and nothing can be done from our side
to fix the problem in it, the driver has to work around this problem. The
WMI_CHAN_FLAG_PASSIVE seems to be interpreted by the firmware to not
scan actively on a channel unless an AP was detected on it. Simple probe
requests will then be transmitted by the STA on the channel.
ath10k must therefore also use this flag when it queues a radar channel for
scanning. This should reduce the chance of an active scan when the channel
might be "unusable" for transmissions.
Fixes: e8a50f8ba4 ("ath10k: introduce DFS implementation")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These were recently introduced and found by checkpatch:
drivers/net/wireless/ath/ath10k/mac.c:6118: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6121: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6124: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Debugfs support to do hardware warm reset with WMI command
WMI_PDEV_PARAM_PDEV_RESET for 10.4 and 10.2.4(if wmi
service is enabled in the firmware for backward compatibility).
This change is purely for debugging purpose when hardware hangs/mutes.
This hardware reset won't affect the connectivity but there will be small
pause in data traffic. Here we are doing BB/MAC level reset and hence
whenever the BB/MAC watchdog is triggered, it does a hardware_chip_reset.
So the target will be in the active state.
Below command used to warm reset the hardware.
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/warm_hw_reset
Tested in QCA988X with firmware ver 10.2.4.70.45
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only code refactoring as all call sites of
ath10k_htt_tx_alloc_msdu_id() take the same lock it can be moved into the
id_get function and the assertion dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables netlen, orig_buf, orig_len, dropped and stats are assigned values
but are never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'netlen' set but not used [-Wunused-but-set-variable]
warning: variable 'orig_buf' set but not used [-Wunused-but-set-variable]
warning: variable 'orig_len' set but not used [-Wunused-but-set-variable]
warning: variable 'dropped' set but not used [-Wunused-but-set-variable]
warning: variable 'stats' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer rf is being assigned but is never used hence it is redundant
and can be removed.
Cleans up two clang warnings:
warning: variable 'rf' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointers dev and noa are being assigned but are never used hence they
are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
warning: variable 'noa' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 transmits management frames via WMI
with reference. Currently, with the management
tx completion not being handled, these frames are
not getting freed even after the transmission status
is returned by the firmware.
The transmitted management frames should be freed
when the firmware sends the over-the-air tx status of
the corresponding management frames.
Handle the wmi mgmt tx completion event and free
the corresponding management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx completion of multiple mgmt frames can be bundled
in a single event and sent by the firmware to host, if this
capability is not disabled explicitly by the host. If the host
cannot handle the bundled mgmt tx completion, this capability
support needs to be disabled in the wmi init cmd, sent to the firmware.
Add the host capability indication flag in the wmi ready command,
to let firmware know the features supported by the host driver.
This field is ignored if it is not supported by firmware.
Set the host capability indication flag(i.e. host_capab) to zero,
for disabling the support of bundle mgmt tx completion. This will
indicate the firmware to send completion event for every mgmt tx
completion, instead of bundling them together and sending in a single
event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.
Tested on QCA9984 with firmware ver 10.4-3.6-00104
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes a recently added checkpatch warning:
wmi-tlv.c:2703: open brace '{' following function definitions go on the next line
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.19. Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbVgnkAAoJEG4XJFUm622b/DAH/0wmjFQrt1qe/goZ4igZOC5z
TTqPUmv7HO4PbHV6mU5yOFGsRCaGDo1cTyEeoiaYNGH6bQLzzJZeQORkuPQB2q5S
BCwlaET7F2iSmk8hx7eboONyVDm5v2+g6NMHBoikVFz1wZ13kCVa4sHkokUJKYB9
XNw3B2OiarPv9i37DlY3woMlY+6VMQh8J6GiB9cJSa4Xs+7l1aQCdQRP03SabI71
gLBEsW+bEVZrUdJGB5cZ8c6LmukmRQMDKMTQYUna5ZXeW1IX3ejYcQGHzzCZoKJS
LPUmisz4014r5aBzXIu3ctVn4LnVhMS5ms0EH1A6IX3vx8G9QynqH5lm9VQ1OXI=
=kWW/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialization is unneccessary when the variable is written before it is
read. There were some occasions in which the driver would initialize `ret'
during declaration without need.
Purely a cosmetic change with no functional impact.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some cases where the device is stuck, reading from OTP
can timeout. As OTP section is known there is no need to read
it during device crash dump collection.
Adding a new field to struct fw_map to indicate if to include
this section in crash dump collection.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn-MB introduces various of FW download options:
FW download via PCIe, SPI or PBL for secured access.
The boot and FW download path is determined based on the
OTP HW register. Driver reads this register as part of the
SW reset flow and performs the appropriate initialization
sequence.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add debugfs support for enhanced DMA TX and RX descriptor rings,
TX and RX status rings and RX buffer management.
Run the following command to print the TX and RX status rings:
cat srings
Run the following command in order to select the status ring:
echo STATUS_RING_IDX > dbg_sring_index
Run the following command in order to select the status message:
echo STATUS_MSG_IDX > dbg_status_msg_index
Run the following command in order to print the selected status
message from the selected status ring:
cat status_msg
Run the following command in order to print the RX buffer management
debug information:
cat rx_buff_mgmt
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enhanced DMA RX data path is handled using a single
RX descriptor ring for all VIFs.
Multiple RX status rings are supported, to allow RSS
and multi MSI support.
The driver gets the RX completions via the RX status rings.
The RX status message includes the completed RX buffer ID,
which points to the allocated SKB.
The enhanced DMA RX data flow supports RX chaining, where
multiple SKBs are merged into a single packet.
Enhanced DMA HW supports RX HW reorder offload, enabled by
default for Talyn-MB.
amsdu_en debugfs entry was added to allow control MSDU aggregation.
Use the following command to disable AMSDU (enabled by default):
echo 0 > amsdu_en
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enhanced DMA TX data path is handled using a descriptor
ring per connection and a single status ring.
The driver gets TX completions via the TX status ring. Each
status message points to the completed descriptor ring and
includes the number of completed descriptors in this ring.
Non TSO enhanced DMA TX descriptors are similar to legacy DMA
TX descriptors, hence the same transmit function can be used.
However, enhanced DMA TSO frames division is performed by the
HW, hence a new function is added to handle enhanced DMA TSO.
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enhanced DMA design includes the following rings:
- Single RX descriptor ring is used for all VIFs
- Multiple RX status rings are supported, to allow RSS
- TX descriptor ring is allocated per connection
- A single TX status ring is used for all TX descriptor rings
This patch initializes and frees the above descriptor and
status rings.
The RX SKBs are handled by a new entity of RX buffers manager,
which handles RX buffers, each one points to an allocated SKB.
During Rx completion processing, the driver extracts a buffer
ID which is used as an index to the buffers array.
After the SKB is freed the buffer is moved from the 'active'
list to the 'free' list, indicating it can be used for another
descriptor. During Rx refill, SKBs are allocated and attached
to 'free' buffers. Those buffers are attached to new descriptors
and moved to the 'active' list.
New debugfs entries were added to allow edma configuration:
Run the following command to configure the number of status rings:
echo NUM_OF_STATUS_RINGS > num_rx_status_rings
Run the following command to use extended RX status message for
additional debug fields from HW:
echo 0 > compressed_rx_status
Run the following command to control the size of the TX status ring:
echo TX_STATUS_RING_ORDER > tx_status_ring_order
The status ring size will be 1 << tx_status_ring_order
Run the following command to control the size of the RX status ring:
echo RX_STATUS_RING_ORDER > rx_status_ring_order
Due to HW constrains RX sring order should be bigger than RX ring order
The status ring size will be 1 << rx_status_ring_order
Run the following command to change the number of RX buffer IDs:
echo RX_BUFF_ID_COUNT > rx_buff_id_count
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In enhanced DMA the vrings are handled internally by the FW
and are not exposed to the driver.
Instead, the driver handles descriptor rings, which are mapped
by the FW to vrings.
The completions of the TX and RX descriptors are notified to
the driver using status rings. Each status ring descriptor
includes information of the completed descriptors and the ring id
of their descriptor ring.
This patch changes struct vring to generic wil_ring to allow
its reuse for enhanced DMA descriptor rings and adds the descriptor
and status rings specific descriptors.
The vring debugfs entries have changed as follows:
- dbg_vring_index has changed to dbg_ring_index
- vrings has changed to rings
- vring_idle_trsh has changed to ring_idle_trsh
- vring_index has changed to ring_index
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add changes to support initialization of Talyn-MB wil6210
device:
- Add definition for Talyn-MB new JTAG id
- Define talyn_mb_fw_mapping array
- Add Talyn-MB reset sequence
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this, packets larger than 1500 will silently be dropped.
Easily reproduced by sending a ping packet with a size larger
than 1500.
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this, when receiving a packet that has this flag set
from firmware, we will read invalid trailer data from the packet,
which will be shown as various errors, e.g. "sdio mbox lookahead
is zero" or "invalid rx packet" or "payload length x exceeds max
htc length".
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All packets in a bundle should use the same endpoint id as the
first lookahead.
This matches how things are done is ath6kl, however,
this patch can theoretically handle several bundles
in ath10k_sdio_mbox_rx_process_packets().
Without this patch we get lots of errors about invalid endpoint id:
ath10k_sdio mmc2:0001:1: invalid endpoint in look-ahead: 224
ath10k_sdio mmc2:0001:1: failed to get pending recv messages: -12
ath10k_sdio mmc2:0001:1: failed to process pending SDIO interrupts: -12
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of WEP encryption, driver has to configure shared key for
associated station(s). Note that sta pointer is NULL in case of non
pairwise key, causing NULL pointer dereference with existing code
(sta_priv->is_data_encrypted). Fix this by using associated sta list
instead. This enables WEP support as client, WEP AP is non-functional.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add list of associated stations(STA, AP, peer...) per vif.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k is the last remaining user of the deprecated getrawmonotonic()
interface. There is nothing wrong with this usage, but migrating
to a timespec64 based interface lets us clean up the old API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardcoded values used in ath10k_mac_tx_push_pending and
ath10k_mac_op_wake_tx_queue set an upper limit of how many packets that
can be consumed from the TX queue.
HTC_HOST_MAX_MSG_PER_TX_BUNDLE is a proper name for this constant, as
the value effectively limits the number of messages that can be consumed
in one step. Thus, the value is an upper limit of the number of messages
that can be added to a TX message bundle.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This define is only used for RX bundling so it is more descriptive if
RX is added to the define-name.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Although the TID mask is 0xf, the modulus operation does still not
produce identical results as the bitwise and operator. If the TID is 15, the
modulus operation will "convert" it to 0, whereas the bitwise and will keep it
as 15.
This was found during code review.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While debugging driver crashes related to a buggy firmware
crashing under load, I noticed that ath10k_htt_rx_ring_free
could be called without being under lock. I'm not sure if this
is the root cause of the crash or not, but it seems prudent to
protect it.
Originally tested on 4.16+ kernel with ath10k-ct 10.4 firmware
running on 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running iperf on ath10k SDIO, TX can stop working:
iperf -c 192.168.1.1 -i 1 -t 20 -w 10K
[ 3] 0.0- 1.0 sec 2.00 MBytes 16.8 Mbits/sec
[ 3] 1.0- 2.0 sec 3.12 MBytes 26.2 Mbits/sec
[ 3] 2.0- 3.0 sec 3.25 MBytes 27.3 Mbits/sec
[ 3] 3.0- 4.0 sec 655 KBytes 5.36 Mbits/sec
[ 3] 4.0- 5.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 5.0- 6.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 6.0- 7.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 7.0- 8.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 8.0- 9.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 9.0-10.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 0.0-10.3 sec 9.01 MBytes 7.32 Mbits/sec
There are frames in the ieee80211_txq and there are frames that have
been removed from from this queue, but haven't yet been sent on the wire
(num_pending_tx).
When num_pending_tx reaches max_num_pending_tx, we will stop the queues
by calling ieee80211_stop_queues().
As frames that have previously been sent for transmission
(num_pending_tx) are completed, we will decrease num_pending_tx and wake
the queues by calling ieee80211_wake_queue(). ieee80211_wake_queue()
does not call wake_tx_queue, so we might still have frames in the
queue at this point.
While the queues were stopped, the socket buffer might have filled up,
and in order for user space to write more, we need to free the frames
in the queue, since they are accounted to the socket. In order to free
them, we first need to transmit them.
This problem cannot be reproduced on low-latency devices, e.g. pci,
since they call ath10k_mac_tx_push_pending() from
ath10k_htt_txrx_compl_task(). ath10k_htt_txrx_compl_task() is not called
on high-latency devices.
Fix the problem by calling ath10k_mac_tx_push_pending(), after
processing rx packets, just like for low-latency devices, also in the
SDIO case. Since we are calling ath10k_mac_tx_push_pending() directly,
we also need to export it.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 5ghz channel parameters of TLV target wasn't passed to host, it caused
host can only use lower channels from 36 to 64.
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Older gcc (< 4.4) doesn't like files starting with a Unicode BOM:
drivers/net/wireless/ath/wcn36xx/testmode.c:1: error: stray ‘\357’ in program
drivers/net/wireless/ath/wcn36xx/testmode.c:1: error: stray ‘\273’ in program
drivers/net/wireless/ath/wcn36xx/testmode.c:1: error: stray ‘\277’ in program
Remove the BOM, the rest of the file is plain ASCII anyway.
Output of "file drivers/net/wireless/ath/wcn36xx/testmode.c" before:
drivers/net/wireless/ath/wcn36xx/testmode.c: C source, UTF-8 Unicode (with BOM) text
and after:
drivers/net/wireless/ath/wcn36xx/testmode.c: C source, ASCII text
Fixes: 87f825e6e2 ("wcn36xx: Add support for Factory Test Mode (FTM)")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the case of Station connects to AP with narrower bandwidth at beginning.
And later the AP changes the bandwidth to winder bandwidth, the AP will
beacon with wider bandwidth IE, eg VHT20->VHT40->VHT80 or VHT40->VHT80.
Since the supported BANDWIDTH will be limited by the PHYMODE, so while
Station receives the bandwidth change request, it will also need to
reconfigure the PHYMODE setting to firmware instead of just configuring
the BANDWIDTH info, otherwise it'll trigger a firmware crash with
non-support bandwidth.
The issue was observed in WLAN.RM.4.4.1-00051-QCARMSWP-1, QCA6174 with
below scenario:
AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 MHz)
disconnect from AP xxx for new auth to yyy
RX ReassocResp from xxx (capab=0x1111 status=0 aid=102)
associated
....
AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 MHz)
AP xxx changed bandwidth, new config is 5200 MHz, width 3 (5210/0 MHz)
....
firmware register dump:
[00]: 0x05030000 0x000015B3 0x00987291 0x00955B31
[04]: 0x00987291 0x00060730 0x00000004 0x00000001
[08]: 0x004089F0 0x00955A00 0x000A0B00 0x00400000
[12]: 0x00000009 0x00000000 0x00952CD0 0x00952CE6
[16]: 0x00952CC4 0x0098E25F 0x00000000 0x0091080D
[20]: 0x40987291 0x0040E7A8 0x00000000 0x0041EE3C
[24]: 0x809ABF05 0x0040E808 0x00000000 0xC0987291
[28]: 0x809A650C 0x0040E948 0x0041FE40 0x004345C4
[32]: 0x809A5C63 0x0040E988 0x0040E9AC 0x0042D1A8
[36]: 0x8091D252 0x0040E9A8 0x00000002 0x00000001
[40]: 0x809FDA9D 0x0040EA58 0x0043D554 0x0042D554
[44]: 0x809F8B22 0x0040EA78 0x0043D554 0x00000001
[48]: 0x80911210 0x0040EAC8 0x00000010 0x004041D0
[52]: 0x80911154 0x0040EB28 0x00400000 0x00000000
[56]: 0x8091122D 0x0040EB48 0x00000000 0x00400600
Reported-by: Rouven Czerwinski <rouven@czerwinskis.de>
Tested-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in wireless-drivers by changing it to BIT_ULL instead. In addition, there are
some places which don't use BIT nor BIT_ULL macros so align those as well.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
random_ether_addr is a #define for eth_random_addr which is
generally preferred in kernel code by ~3:1
Convert the uses of random_ether_addr to enable removing the #define
Miscellanea:
o Convert &vfmac[0] to equivalent vfmac and avoid unnecessary line wrap
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.19. Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
Trivial fix to spelling mistake in PR_IS message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of resource init method is not assigned.
Handle resource init failures for graceful exit.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In non-bmi target ex. WCN3990, data calibration
is handled via QMI.
Skip data calibration in debug routine to enable ath10k
debugfs for non bmi targets.
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sort these alphabetically, with local includes in a separate section.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We started using a common CE_ATTR_FLAGS definition, so drop this one.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's easier to violate abstractions and introduce bugs when snoc.h is
including pci.h. Let's not do that.
I'm not extremely familiar with this driver yet, but several of the
shared PCI/SNOC bits seem to be related to the Copy Engine, so move them
to ce.h.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We're 'ath10k_snoc', not 'ath10k_pci'. This probably means we're
accessing junk data in ath10k_snoc_rx_replenish_retry(), unless
'ath10k_snoc' and 'ath10k_pci' happen to have very similar struct
layouts.
Noticed by inspection.
Fixes: d915105231 ("ath10k: add hif rx methods for wcn3990")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_snoc_init()/ath10k_snoc_exit() don't add much value;
module_platform_driver() can remove the boilerplate.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The comments are telling you what the enum could tell you instead.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sizeof(struct ce_desc) should be a copy-paste mistake
just use sizeof(struct ce_desc_64) to avoid mem leak
Fixes: b7ba83f7c4 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warnings:
drivers/net/wireless/ath/ath10k/snoc.c:823:5: warning:
symbol 'ath10k_snoc_get_ce_id_from_irq' was not declared. Should it be static?
drivers/net/wireless/ath/ath10k/snoc.c:871:6: warning:
symbol 'ath10k_snoc_init_napi' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The spectral scan has been always broken on QCA9984 and QCA9888.
Introduce a hardware parameter 'spectral_bin_offset' to resolve this issue for
QCA9984 and QCA9888 chipsets. For other chipsets, the hardware parameter
'spectral_bin_offset' is zero so that existing behaviour is retained as it is.
In QCA9984 and QCA9888 chipsets, hardware param value 'spectral_bin_discard'
is 12 bytes. This 12 bytes is derived as the sum of segment index (4 bytes),
extra bins before the actual data (4 bytes) and extra bins after the actual
data (4 bytes). Always discarding (12 bytes) happens at end of the samples and
incorrect samples got dumped, so that user can find incorrect arrangement
samples in spectral scan dump.
To fix this issue, we have to discard first 8 bytes and last 4 bytes in every
samples, so totally 12 bytes are discarded. In every sample we need to consider
the offset while taking the actual spectral data. For QCA9984, QCA9888 the
offset is 8 bytes (segment index + extra bins before actual data).
Hardware tested: QCA9984 and QCA9888
Firmware tested: 10.4-3.5.3-00053
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The India regulatory domain allows CH 173, so add that to the
available channel list. I verified basic connectivity between
a 9880 and 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently tpc_stats is allocated and is leaked on the return
path if num_tx_chain is greater than WMI_TPC_TX_N_CHAIN. Avoid
this leak by performing the check on num_tx_chain before the
allocation of tpc_stats.
Detected by CoverityScan, CID#1469422 ("Resource Leak")
Fixes: 4b190675ad ("ath10k: fix kernel panic while reading tpc_stats")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a Qualcomm Atheros AR6004X with an sdio ID of 0x19 and hardware ID of
0271:0419. Tested on a Dell Venue 11 Pro 7130 with a self compiled kernel.
Signed-off-by: Guy Chronister <guylovesbritt@gmail.com>
[kvalo@codeaurora.org: cleanup commit log]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced "pass through" with
a proper "fall through" comment, which is what GCC is expecting
to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbD/3rAAoJEG4XJFUm622b1ZwH/1xe1IqcwJXzfoDsYPlXVnSh
TiLExjKkD0ty5M0//844FxpxE1sSYJKOJ11uz/COzyG2qi4+5lgpUdjnDoINuKfH
ycqrXGssW7ogPWkVvnxKtlEYvkHNRYLQtxvd26umT77C69jVJLD0x9uihhh2En/C
EKs+OK1Pp0SRvTfB4AblWzoAnpEe1wHJFFh4i3F5H0lMGxLQz/YjFl5aeAjjR406
0vSKLGy2wKIydp8Pe4cAqBEeUWDJurn8ufkk7bmAET5zaXTH1qgZzLH3OWtx/ksz
mcPQq9/ctv35G2917t3Sn69SIUCDGfYkP5DiZV+ti0Hz2gIV0zOg7mGYCU8uHaU=
=11X5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce infrastructure for supporting Factory Test Mode (FTM) of the
wireless LAN subsystem. In order for the user space to access the
firmware in test mode the relevant netlink channel needs to be exposed
from the kernel driver.
The above is achieved as follows:
1) Register wcn36xx driver to testmode callback from netlink
2) Add testmode callback implementation to handle incoming FTM commands
3) Add FTM command packet structure
4) Add handling for GET_BUILD_RELEASE_NUMBER (msgid=0x32A2)
5) Add generic handling for all PTT_MSG packets
Signed-off-by: Eyal Ilsar <eilsar@codeaurora.org>
Signed-off-by: Ramon Fried <ramon.fried@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the 10.4-3.6 firmware branch there's a new DFS Host confirmation
feature which is advertised using WMI_SERVICE_HOST_DFS_CHECK_SUPPORT flag.
This new features enables the ath10k host to send information to the
firmware on the specifications of detected radar type. This allows the
firmware to validate if the host's radar pattern detector unit is
operational and check if the radar information shared by host matches
the radar pulses sent as phy error events from firmware. If the check
fails the firmware won't allow use of DFS channels on AP mode when using
FCC regulatory region.
Hence this patch is mandatory when using a firmware from 10.4-3.6 branch.
Else, DFS channels on FCC regions cannot be used.
Supported Chipsets : QCA9984/QCA9888/QCA4019
Firmware Version : 10.4-3.6-00104
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enables ath10k/ath9k drivers to collect the specifications of the
radar type once it is detected by the dfs pattern detector unit.
Usage of the collected info is specific to driver implementation.
For example, collected radar info could be used by the host driver
to send to co-processors for additional processing/validation.
Note: 'radar_detector_specs' data containing the specifications of
different radar types which was private within dfs_pattern_detector/
dfs_pri_detector is now shared with drivers as well for making use
of this information.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a missing newline in wcn36xx_smd_send_and_wait() and also log the
command request and response type that was processed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Drop the extra warning about failed allocations, both the core and the
only caller of this function will warn loud enough in such cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the interface is shut down, wcn36xx_smd_close() potentially races
against the queue worker. Make sure to cancel the work, and then free all
the remnants in hal_ind_queue manually.
This is again just a theoretical issue, not something that was triggered in
the wild.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a BSSID is joined, set the link status to 'preassoc', and set it to
'idle' when the BSS is deleted.
This is what the downstream driver is doing, and it seems to improve the
reliability during connect/disconnect stress tests.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In reap_tx_dxes(), when we iterate over the linked descriptors, only
consider such valid that have WCN36xx_DXE_CTRL_EOP set.
This is what the prima downstream driver is doing as well.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On RX and TX interrupts, check for the WCN36XX_CH_STAT_INT_ED_MASK or
WCN36XX_CH_STAT_INT_DONE_MASK in the interrupt reason register, and
only handle packets when it is set. This way, reap_tx_dxes() is only
invoked when needed.
This brings the dequeing logic in line with what the prima downstream
driver is doing.
While at it, also log the interrupt reason.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Like on the TX side, check for the interrupt reason when the RX interrupt
is latched and clear the ERR, DONE and ED masks.
This seems to help with connection timeouts and network stream
starvatations. And FWIW, the downstream driver does the same thing.
Note that in analogy to the TX side, WCN36XX_DXE_0_INT_CLR should be set to
WCN36XX_INT_MASK_CHAN_RX_{L,H} rather than WCN36XX_DXE_INT_CH{1,3}_MASK. It
did the right thing however, as the defines happen to have identical values.
Also, instead of determining register addresses and values inside
wcn36xx_rx_handle_packets(), pass them as arguments.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's no need to disable the IRQ from inside its handler.
Instead just grab the spinlock of the channel that is being processed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The device takes 32-bit addresses only, so inform the DMA API about it.
This is the default on msm8016, so that doesn't change anything, but
it's best practice to be explicit.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When wcn36xx_dxe_tx_frame() is entered while the device is still processing
the queue asyncronously, we are racing against the firmware code with
updates to the buffer descriptors. Presumably, the firmware scans the ring
buffer that holds the descriptors and scans for a valid control descriptor,
and then assumes that the next descriptor contains the payload. If, however,
the control descriptor is marked valid, but the payload descriptor isn't,
the packet is not sent out.
Another issue with the current code is that is lacks memory barriers before
descriptors are marked valid. This is important because the CPU may reorder
writes to memory, even if it is allocated as coherent DMA area, and hence
the device may see incompletely written data.
To fix this, the code in wcn36xx_dxe_tx_frame() was restructured a bit so
that the payload descriptor is made valid before the control descriptor.
Memory barriers are added to ensure coherency of shared memory areas.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: ETSI -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: ETSI -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: FCC -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure channel dwell time from duration of the scan request
received from mac80211 when the duration is non-zero. When the
scan request does not have duration value, use the default ones,
the current implementation.
Corresponding flag NL80211_EXT_FEATURE_SET_SCAN_DWELL is
advertized.
Supported Chipsets:
-QCA988X/QCA9887 PCI
-QCA99X0/QCA9984/QCA9888/QCA4019 PCI
-QCA6174/QCA9377 PCI/USB/SDIO
-WCN3990 SNOC
Tested on QCA9984 with firmware ver 10.4-3.6-0010
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware crash memory dump support for QCA9888 and QCA99X0.
Tested on:
QCA9888 firmware 10.4-3.5.3-00053
QCA99X0 firmware 10.4.1.00030-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are specific cases, such as SAE authentication exchange, that
might require long duration to complete. For such cases, add support
for indicating to the driver the required duration of the prepare_tx()
operation, so the driver would still be able to complete the frame
exchange.
Currently, indicate the duration only for SAE authentication exchange,
as SAE authentication can take up to 2000 msec (as defined in IEEE
P802.11-REVmd D1.0 p. 3504).
As the patch modified the prepare_tx() callback API, also modify
the relevant code in iwlwifi.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ath.git patches for 4.18. Major changes:
ath10k
* add quiet mode support for QCA6174/QCA9377
wil6210
* disable WIL6210_TRACING kconfig option by default
The ath10k testmode uses request_firmware_direct() in order to avoid
producing firmware load warnings. Disabling the fallback mechanism was a
side effect of disabling warnings.
We now have a new API that allows us to avoid warnings while keeping the
fallback mechanism enabled. So use that instead.
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reduces the unnecessary spew when trying to load optional firmware:
"Direct firmware load for ... failed with error -2"
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wil_err inside wil_rx_refill can flood the log buffer.
Replace it with wil_err_ratelimited.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove unused members from struct wil_tid_ampdu_rx
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WMI command reply saved in uninitialized struct.
In order to avoid accessing unset values from FW initialize
the reply struct.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rearrange the code by having new function wmi_mgmt_tx() to take care
of the WMI part of wil_cfg80211_mgmt_tx().
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change the type of the argument reply_size from u8 to
u16 in order to support reply sizes > 255 bytes.
The driver already supports u16 reply size in all
other places, this was the only missing change.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move the call to wil6210_disconnect so it will be called
before unregister_netdevice. This is because it calls
netif_carrier_off which is forbidden to call on an
unregistered net device. Calling netif_carrier_off can
add a link watch event which might be handled after
net device was freed, causing a kernel oops.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to latest version of the auto generated wmi file
describing the interface with FW
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disable WIL6210_TRACING by default to avoid its performance overhead.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the BIT() macro from 'linux/bitops.h' to define the rx desc
bit flags to have consistency with new definitions.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some reason not all entries used ATH10K_FW_DIR so fix that. No functional
changes.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable buf_len and num_vdev_stats are being assigned but never read.
These are redundant and can be remove.
Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_mac_tx_push_txq returns either a postive integer (length) on
success or a negative error code on error.
The "if (ret) break;" statement will thus always break out of the loop
immediately after ath10k_mac_tx_push_txq has returned (making the loop
pointless).
A side effect of this fix is that we will iterate the queue until
ath10k_mac_tx_push_txq returns -ENOENT. This will make sure the queue is
not added back to ar->txqs when it is empty. This could potentially
improve performance somewhat (I have seen a small improvement with SDIO
devices).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Structure platform_driver does not need to set the owner field, as this
will be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To enable thermal throttling for QCA6174 and QCA9377,
implement gen_pdev_set_quiet_mode for them.
With this change, quiet period for QCA6174/QCA9377 can
be also set/get via debugfs.
Usage:
To set quiet period:
echo <period> > /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period
To get the current quiet period:
cat /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period
This change has been verified with
QCA6174 hw3.2(fw: WLAN_RM.4.4.1-00102-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the addition of the TXQ stats to cfg80211, the station_info struct
has grown to be quite large, which results in warnings when allocated on
the stack. Fix the affected places to do dynamic allocations instead.
Fixes: 52539ca89f ("cfg80211: Expose TXQ stats and parameters to userspace")
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jump to the correct label in error handling path.
At this point of execution create_singlethread_workqueue() has succeeded,
so it should be properly destroyed.
Jump label was renamed in commit ec2c64e202 ("ath10k: sdio: fix memory
leak for probe allocations").
However, the bug was originally introduced in commit d96db25d20
("ath10k: add initial SDIO support").
Fixes: d96db25d20 ("ath10k: add initial SDIO support")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in ath10k_warn warning message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During write to some of debugfs in ath10k, few variables exposing stack
data when process user input. which leads to possible information leak.
This patch fix this issue by initializing buffer and checks
the return valure of 'simple_write_to_buffer'.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.18. Major changes:
ath10k
* enable temperature reads for QCA6174 and QCA9377
* add firmware memory dump support for QCA9984
* continue adding WCN3990 support via SNOC bus
When the wifi driver core passes IE elements in the scan request, append
them to the firmware message. The driver currently tells the core that
it is capable of attaching up to WCN36XX_MAX_SCAN_IE_LEN octets, but
doesn't actually pass them to the the hardware.
Note that this patch doesn't fix a bug that was observed. The change is
merely done for the sake of completeness as the hardware supports
appending IEs in scans. Tests show that network scans work fine with
this patch applied.
Some defines were moved around to avoid cyclic include dependencies.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pass the bss_type of the currently configured BSS in the message for the
scan request. Therefore, that setting needs to be kept in struct
wcn36xx_vif.
This seems to be only interesting when scanning for a specific SSID
and doesn't matter for regular wildcard scans.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For firmwares that don't have the SCAN_OFFLOAD feature bit set, do
not call into wcn36xx_smd_stop_hw_scan(). Instead, stop the asynchronous
work and call into ieee80211_scan_completed() immediately.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the network interface goes down while a scan request is still
pending that can't be stopped due to firmware hickups, wcn->scan_req
remains set, even though the hardware is deinitialized. This results
in -EBUSY for all scan requests after the interface was brought up
again.
Fix this by explicitly completing pending scan requests in
wcn36xx_stop().
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the firmware sends a WCN36XX_HAL_SCAN_IND_DEQUEUED indication,
the request is apparently no longer valid. Attempts to stop the hardware
scan request subsequently will lead to the following error message, and
the hardware is no longer able to communicate with any AP:
[ 57.917186] wcn36xx: ERROR hal_stop_scan_offload response failed err=5
Interpreting this indicator message as scan abortion fixes this.
While at it, add a newline to a debug print.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable sta power save in fw for the targets that
supports idle power save. The idle ps enable command
will be ignored by the firmware which does not support
this feature.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SRRI/DRRI are not mapped in the HW Shadow block and can lead
to un-clocked access if common subsystem in the target is
powered down due to idle mode.
To mitigate this problem SRRI/DRRI can be read from
DDR instead of doing an actual hardware read.
Host allocates non cached memory on ddr and configures
the physical address of this memory to the CE hardware.
The hardware updates the RRI on this particular location.
Read SRRI/DRRI from DDR location instead of
direct target read.
Enable retention restore on ddr using hw params to enable
in specific targets.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 needs shadow register write operation support
for copy engine for regular operation in powersave mode.
Add support for copy engine shadow register write in
datapath tx for WCN3990
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn3990 supports shadow register for ce write.
Add a hw param for shadow register support.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By default ath10k driver enables the support for HW_CHECKSUM
(NETIF_F_HW_CSUM). Since the TCP/UDP checksum calculation is not enabled
in the wcn3990 firmware the checksum is incorrect in the TCP/UDP packets
and all patckets are dropped. But due note that wcn3990 support in
ath10k is still incomplete so this isn't a critical fix (yet).
Enable hw checksum calculations in wcn3990 hardware by
setting the proper flags in msdu descriptor tso flags.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware message to delete BSS keys expects a BSS index to be passed.
This field is currently hard-coded to 0. Fix this by passing in the index
we received from the firmware when the BSS was configured.
The encryption type in that message also needs to be set to what was used
when the key was set, so the assignment of vif_priv->encrypt_type is now
done after the firmware command was sent. This reportedly fixes the
following error in AP mode:
wcn36xx: ERROR hal_remove_bsskey response failed err=6
Also, AFAIU, when a BSS is deleted, the firmware apparently drops all the
keys associated with it. Trying to remove the key explicitly afterwards
will hence lead to the following message:
wcn36xx: ERROR hal_remove_bsskey response failed err=16
This is now suppressed with an extra check for the BSS index validity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When trying to set wow wakeup patterns it fails with this command:
iw phyxx wowlan enable patterns offset xx+ IP address xx.xx.xx.xx
The reason is that the wow pattern from upper layer is in 802.3 format
for this case, it need to convert it to 802.11 format. The input
offset parameter is used for 802.3, but the actual offset firmware
need depends on rx_decap_mode, so that it needs to be recalculated.
Pattern of 802.3 packet is not same with 802.11 packet. If the
rx_decap_mode is ATH10K_HW_TXRX_NATIVE_WIFI, then firmware will
receive data packet with 802.11 format from hardware.
Tested with QCA6174 hw3.0 with firmware
WLAN.RM.4.4.1-00099-QCARMSWPZ-1, but this will also affect QCA9377.
This has always failed, so it's not a regression with new firmware
releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.
Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When accessing shared memory to check for the stat of submitted
descriptors, make sure to use READ_ONCE(). This will guarantee the
compiler treats these memory locations as volatile and doesn't apply
any caching.
While this doesn't fix any particular problem I ran into, it's best
practice to do it this way.
Note that this patch also removes the superflous extra condition check
in the do-while loop in reap_tx_dxes(), as the loop will break
instantly anyway in that case.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW path is mapped incorrectly for the WCN3990
hw version. Fix fw path with correct hw1.0 name.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added for the same reason as the TX wrappers.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These wrappers makes the HTT ops align better with the HIF ops
(where similar wrappers are used).
It also makes it easier for a target to have unsupported ops
(by letting the corresponding function pointer be NULL).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
commit f2593cb1b2 ("ath10k: Search SMBIOS for OEM board file
extension") added a feature to ath10k that allows Board Data File
(BDF) conflicts between multiple devices that use the same device IDs
but have different calibration requirements to be resolved by allowing
a "variant" string to be stored in SMBIOS [and later device tree, added
by commit d06f26c5c8 ("ath10k: search DT for qcom,ath10k-calibration-
variant")] that gets appended to the ID stored in board-2.bin.
This original patch had a regression, however. Namely that devices with
a variant present in SMBIOS that didn't need custom BDFs could no longer
find the default BDF, which has no variant appended. The patch was
reverted and re-applied with a fix for this issue in commit 1657b8f84e
("search SMBIOS for OEM board file extension").
But the fix to fall back to a default BDF introduced another issue: the
driver currently parses IEs in board-2.bin one by one, and for each one
it first checks to see if it matches the ID with the variant appended.
If it doesn't, it checks to see if it matches the "fallback" ID with no
variant. If a matching BDF is found at any point during this search, the
search is terminated and that BDF is used. The issue is that it's very
possible (and is currently the case for board-2.bin files present in the
ath10k-firmware repository) for the default BDF to occur in an earlier
IE than the variant-specific BDF. In this case, the current code will
happily choose the default BDF even though a better-matching BDF is
present later in the file.
This patch fixes the issue by first searching the entire file for the ID
with variant, and searching for the fallback ID only if that search
fails. It also includes some code cleanup in the area, as
ath10k_core_fetch_board_data_api_n() no longer does its own string
mangling to remove the variant from an ID, instead leaving that job to a
new flag passed to ath10k_core_create_board_name().
I've tested this patch on a QCA4019 and verified that the driver behaves
correctly for 1) both fallback and variant BDFs present, 2) only fallback
BDF present, and 3) no matching BDFs present.
Fixes: 1657b8f84e ("ath10k: search SMBIOS for OEM board file extension")
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix a typo in the function ath10k_wmi_set_wmm_param().
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct a minor bug in the commit 0628467f97 ("ath10k: fix
copy engine 5 destination ring stuck") which introduced a change to fix
firmware assert that happens when ring indices of copy engine 5 are stuck
for a specific duration, problem with this fix is that it did not use
ring arithmatic. As a result,firmware asserts did not go away entirely
athough the frequency of occurrence has reduced. Using ring arithmatic
to fix the issue.
Tested on QCA9984(fw version-10.4-3.4-00082).
Fixes: 0628467f97 ("ath10k: fix copy engine 5 destination ring stuck)
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add clock and regulator votes for WCN3990 WLAN
chipset.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 has interrupts per CE and the interrupt summary
is not retained after the interrupt handler has finished
execution. We need to check if we received any
ce in rx and tx completion path.
Generate a interrupt summary with all CE interrupts if
the target does not retain interrupt summary after the
execution of interrupt handler.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn3990 does not use bmi.
Add support to get target info from hif ops.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change type of hif sg tx paddr to dma_addr_t for
supporting target having addressing mode greater than
32 bit.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hif rx methods in rx path for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hif tx/tx-complete methods for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hif power-up/power-down methods for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add mapping of HTC endpoint services supported
by wcn3990 target to tx/rx pipe.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 target uses 3 Copy engine(CE1/CE9/CE10) in RX path
and CE 11 for pktlog.
Add data path HTC ep services and PKTLOG services for WCN3990.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hif start/stop callback for allocating/freeing buffers
on tx/rx pipe and enabling/disabling the tx/rx pipe
interrupts.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is integrated 802.11ac chipset with SNOC
bus interface. Add snoc layer driver registration
and associated ops.
WCN3990 support is not yet complete as cold-boot
handshake is done using qmi(Qualcomm-MSM-Interface)
and qmi client support will be added once qmi framework
is available.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CE layer is shared between pci and snoc target and results
in duplicate object inclusion if both modules are compiled
together statically and undefined KBUILD_MODNAME if
compiled as module.
Fix this by building ce layer in ath10k core module by
adding ce object inclusion with ATH10K_CE boolean CONFIG.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add support to get RSSI from acknowledgment
frames for transmitted management frames.
hardware_used: QCA4019, QCA9984.
firmware version: 10.4-3.5.3-00052.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
GFP_ATOMIC should only be used when the allocation is done from atomic
context. Introduce a new flag to wcn36xx_dxe_fill_skb() and use GFP_KERNEL
when pre-allocating buffers during init.
This doesn't fix an issue that was observed in the wild, but it reduces
the chance of failed allocations under memory pressure.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each DXE control block is associated to a specific channel.
The channel lock is always taken before accessing a control block.
There is no need to have an extra (useless) spinlock for the control
block skb.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This prevents GCC warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware code cannot cope with requests to remove BSS indices that have
not previously been added. This primarily happens when the device is
suspended and then resumed. ieee80211_reconfig() then calls into
wcn36xx_bss_info_changed() with an empty bssid and BSS_CHANGED_BSSID set,
which subsequently leads to a firmware crash:
[ 43.647928] qcom-wcnss-pil a204000.wcnss: fatal error received: halMsg.c:4964:halMsg_DelBss: Invalid BSSIndex 0
[ 43.647959] remoteproc remoteproc0: crash detected in a204000.wcnss: type fatal error
To fix this, set bss_index to WCN36XX_HAL_BSS_INVALID_IDX for all bss
that have not been configured in the firmware, and don't call into the
firmware with invalid indices.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When wcn36xx_dxe_tx_frame() fails to transmit the TX frame, the driver
will call into ieee80211_free_txskb() for the skb in flight, so it'll no
longer be valid. Hence, we shouldn't keep a reference to it in ctl->skb.
Also, if the skb has IEEE80211_TX_CTL_REQ_TX_STATUS set, a pointer to
it will currently remain in wcn->tx_ack_skb, which will potentially lead
to a crash if accessed later.
Fix this by checking the return value of wcn36xx_dxe_tx_frame(), and
nullify wcn->tx_ack_skb again in case of errors. Move the assignment
of ctl->skb in wcn36xx_dxe_tx_frame() so it only happens when the
transmission is successful.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bail out if the mapping fails. Even though this hasn't occured during
tests, this unlikely case should still be handled.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wvla, remove accidental use of stack VLA.
This avoids an accidental stack VLA (since the compiler thinks
the value of FFT_NUM_SAMPLES can change, even when marked
"const"). This just replaces it with a #define.
Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These allocations are not freed upon release.
When on it; go for managed resources instead.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
[kvalo: fix two checkpatch warnings]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The pointer ndev is being dereferenced before it is being null checked,
hence there is a potential null pointer deference. Fix this by only
dereferencing ndev after it has been null checked
Detected by CoverityScan, CID#1467010 ("Dereference before null check")
Fixes: e00243fab8 ("wil6210: infrastructure for multiple virtual interfaces")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The way that 'strncat' is used here raised a warning in gcc-8:
drivers/net/wireless/ath/ath10k/wmi.c: In function 'ath10k_wmi_tpc_stats_final_disp_tables':
drivers/net/wireless/ath/ath10k/wmi.c:4649:4: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
Effectively, this is simply a strcat() but the use of strncat() suggests
some form of overflow check. Regardless of whether this might actually
overflow, using strlcat() instead of strncat() avoids the warning and
makes the code more robust.
Fixes: bc64d05220 ("ath10k: debugfs support to get final TPC stats for 10.4 variants")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
Remove the static array and use the generic routine to set the
Ethernet broadcast address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently vdev stats displayed in fw_stats are applicable
only for TLV based firmware and fix it for 10.4 firmware
as of now. The vdev stats in 10.4 firmware is split into two
parts (vdev_stats, vdev_stats_extended). The actual stats
are captured only in extended vdev stats. In order to enable
vdev stats, appropriate feature bit will be set on extended
resource config. As FTM related counters are available only on
newer 10.4 based firmware, these counters will be displayed
only on valid data.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The commit "cfg80211: make RATE_INFO_BW_20 the default" changed
the index of RATE_INFO_BW_20, but the updates to ath10k missed
the special bandwidth calculation case in
ath10k_update_per_peer_tx_stats().
This will fix below warning,
WARNING: CPU: 0 PID: 609 at net/wireless/util.c:1254
cfg80211_calculate_bitrate+0x174/0x220
invalid rate bw=1, mcs=9, nss=2
(unwind_backtrace) from
(cfg80211_calculate_bitrate+0x174/0x220)
(cfg80211_calculate_bitrate) from
(nl80211_put_sta_rate+0x44/0x1dc)from
(nl80211_put_sta_rate) from
(nl80211_send_station+0x388/0xaf0)
(nl80211_get_station+0xa8/0xec)
[ end trace da8257d6a850e91a ]
Fixes: 842be75c77 ("cfg80211: make RATE_INFO_BW_20 the default")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes regression caused by 0c317a02ca
("cfg80211: support virtual interfaces with different beacon intervals"),
with this change cfg80211 expects the driver to advertize
'beacon_int_min_gcd' to support different beacon intervals in multivap
scenario. This support is added for, QCA988X/QCA99X0/QCA9984/QCA4019.
Verifed AP + mesh bring up on QCA9984 with beacon interval 100msec and
1000msec respectively.
Frimware: firmware-5.bin_10.4-3.5.3-00053
Fixes: 0c317a02ca ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For WPA encryption, QCA6174 firmware(version: WLAN.RM.4.4) will unblock
data when M4 was sent successfully. For other encryption which didn't need
4-way handshake firmware will unblock the data when peer authorized. Since
TDLS is 3-way handshake host need send authorize cmd to firmware to unblock
data.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TDLS peer do not need WEP key. Setting WEP key will lead
to TDLS setup failure. Add fix to avoid setting WEP key
for TDLS peer.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable TDLS peer inactivity detetion feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting.
Set related parameters in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable TDLS peer buffer STA feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA,
it reports this capability through wmi service map in wmi service ready
event. Set related parameter in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case wcn36xx_smd_rsp_process() is called more than once before
hal_ind_work was dispatched, the messages will end up in hal_ind_queue,
but wcn36xx_ind_smd_work() will only look at the first message in that
list.
Fix this by dequeing the messages from the list in a loop, and only stop
when it's empty.
This issue was found during a review of the driver. In my tests, that
race never actually occured.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx_start_tx function retrieves the buffer descriptor from the
channel control queue to start filling tx buffer information. However,
nothing prevents this same buffer to be concurrently accessed in a
concurent tx call, leading to potential buffer coruption and firmware
crash (observed during iperf test). The channel control queue should
only be accessed and updated with the channel lock.
Fix this issue by using a local buffer descriptor which will be copied
in the thread-safe wcn36xx_dxe_tx_frame.
Note that buffer descriptor size is few bytes so the introduced copy
overhead is insignificant. Moreover, this allows to keep the locked
section minimal.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It appears that the WCN36xx firmware doesn't actually respond to
probe requests. Until it's resolved, switch the probe response
responsibility to the 802.11 layer to allow creation of
hidden SSID AP's.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
QCA9984/QCA99X0/QCA4019 chipsets have 8 memory regions, dump all of them to the
firmware coredump file. Some of the regions need to be read using ioread() so
add new region types for them.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[kvalo: refactoring etc]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As QCA9984 needs two region types refactor the code to make it easier add the
new types. No functional changes.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW has Smart Logging feature enabled by default for detecting failures
and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.
Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
EVENT processing yet, suppressing the unknown event ID warning by moving
this under ATH10K_DBG_WMI.
Simulated the same issue by having associated STA powered off when
ping flood was running from AP backbone. This triggerd STA KICKOUT
in AP followed by FATAL CONDITION event 36925.
Issue was reproduced and verified in below DUT
------------------------------------------------
AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware WLAN.TF.2.1-00014-QCARMSWP-1 now supports reading the board ID
information and also required 9 IRAM bank, which older ath10k version
don't have the support will fail to be enabled, so in order to maintain
the backward compatibility, we need to update the FW API to 6.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware of QCA6174/QCA9377 already support the feature, just enable
it to be able to handle the get_temperature command and process the event.
You can read the temperature by using the hwmon interface,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Verified with the following hardware and software combination,
QCA6174, only firmware-4.bin doesn't support this, otherwise all support.
QCA9377, all the firmwares upstreamed support this command
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
some userspace programs (e.g. hostapd) need to set the regulatory domain
before selecting the operating channel. Synchronize DFS detector regardless of
the value of ah->curchan, to avoid situations where wireless scan can't be done
on some 5GHz sub-bands, because dfs_region is constantly UNSET.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Timothy Redaelli <tredaelli@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
IRQ reason was not cheked for errors.
Although error handing is not currently supported, it
will be nice to output an error value to the log if the
DMA operation failed.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DXE channel defaults used hardcoded magic values.
Added bit definitions of the control register and
calculate this values in compilation for clarity.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DXE descriptor control registers used hardcoded magic values. Added bit
definitions of the control register and calculate this values in compilation
for clarity. No functional changes.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When attempt to run worker (ath10k_sta_rc_update_wk) after the station object
(ieee80211_sta) delete will trigger the kernel panic.
This problem arise in AP + Mesh configuration, Where the current node AP VAP
and neighbor node mesh VAP MAC address are same. When the current mesh node
try to establish the mesh link with neighbor node, driver peer creation for
the neighbor mesh node fails due to duplication MAC address. Already the AP
VAP created with same MAC address.
It is caused by the following scenario steps.
Steps:
1. In above condition, ath10k driver sta_state callback (ath10k_sta_state)
fails to do the state change for a station from IEEE80211_STA_NOTEXIST
to IEEE80211_STA_NONE due to peer creation fails. Sta_state callback is
called from ieee80211_add_station() to handle the new station
(neighbor mesh node) request from the wpa_supplicant.
2. Concurrently ath10k receive the sta_rc_update callback notification from
the mesh_neighbour_update() to handle the beacon frames of the above
neighbor mesh node. since its atomic callback, ath10k driver queue the
work (ath10k_sta_rc_update_wk) to handle rc update.
3. Due to driver sta_state callback fails (step 1), mac80211 free the station
object.
4. When the worker (ath10k_sta_rc_update_wk) scheduled to run, it will access
the station object which is already deleted. so it will trigger kernel
panic.
Added the peer exist check in sta_rc_update callback before queue the work.
Kernel Panic log:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0204000
[00000000] *pgd=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
CPU: 1 PID: 1833 Comm: kworker/u4:2 Not tainted 3.14.77 #1
task: dcef0000 ti: d72b6000 task.ti: d72b6000
PC is at pwq_activate_delayed_work+0x10/0x40
LR is at pwq_activate_delayed_work+0xc/0x40
pc : [<c023f988>] lr : [<c023f984>] psr: 40000193
sp : d72b7f18 ip : 0000007a fp : d72b6000
r10: 00000000 r9 : dd404414 r8 : d8c31998
r7 : d72b6038 r6 : 00000004 r5 : d4907ec8 r4 : dcee1300
r3 : ffffffe0 r2 : 00000000 r1 : 00000001 r0 : 00000000
Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: 595bc06a DAC: 00000015
...
Process kworker/u4:2 (pid: 1833, stack limit = 0xd72b6238)
Stack: (0xd72b7f18 to 0xd72b8000)
7f00: 00000001 dcee1300
7f20: 00000001 c02410dc d8c31980 dd404400 dd404400 c0242790 d8c31980 00000089
7f40: 00000000 d93e1340 00000000 d8c31980 c0242568 00000000 00000000 00000000
7f60: 00000000 c02474dc 00000000 00000000 000000f8 d8c31980 00000000 00000000
7f80: d72b7f80 d72b7f80 00000000 00000000 d72b7f90 d72b7f90 d72b7fac d93e1340
7fa0: c0247404 00000000 00000000 c0208d20 00000000 00000000 00000000 00000000
7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<c023f988>] (pwq_activate_delayed_work) from [<c02410dc>] (pwq_dec_nr_in_flight+0x58/0xc4)
[<c02410dc>] (pwq_dec_nr_in_flight) from [<c0242790>] (worker_thread+0x228/0x360)
[<c0242790>] (worker_thread) from [<c02474dc>] (kthread+0xd8/0xec)
[<c02474dc>] (kthread) from [<c0208d20>] (ret_from_fork+0x14/0x34)
Code: e92d4038 e1a05000 ebffffbc[69210.619376] SMP: failed to stop secondary CPUs
Rebooting in 3 seconds..
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The skb may be freed in tx completion context before
trace_ath10k_wmi_cmd is called. This can be easily captured when
KASAN(Kernel Address Sanitizer) is enabled. The fix is to move
trace_ath10k_wmi_cmd before the send operation. As the ret has no
meaning in trace_ath10k_wmi_cmd then, so remove this parameter too.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the WLAN interface is started the FW
version and caps are printed.
The caps now will be displayed only in debug mode.
Firmware version will be displayed only once on first
startup of the interface.
Change-Id: I4db6ea7f384fe15eebe4c3ddb1d1ccab00094332
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes false radar detection (of radar type 7)
in Japan region by correcting the radar pulse type
to Chirp as per specification.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Export the final Transmit Power Control (TPC) value, which is the
minimum of control power and existing TPC value to user space via
a new debugfs file "tpc_stats_final" to help with debugging.
It works with the new wmi cmd and event introduced in 10.4 firmware
branch.
WMI command ID: WMI_PDEV_GET_TPC_TABLE_CMDID
WMI event ID: WMI_PDEV_TPC_TABLE_EVENTID
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
$ cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
TPC config for channel 5180 mode 10
CTL = 0x 0 Reg. Domain = 58
Antenna Gain = 0 Reg. Max Antenna Gain = 0
Power Limit = 60 Reg. Max Power = 60
Num tx chains = 2 Num supported rates = 109
******************* CDD POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
******************* STBC POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
***********************************
TXBF not supported
**********************************
The existing tpc_stats debugfs file provides the dump
which is minimum of target power and regulatory domain.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats
Hardware_used: QCA4019
Firmware version: firmware-5.bin_10.4-3.0-00209
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added per tid sta counters for the following
- Total number MSDUs received from firmware
- Number of MSDUs received with errors like decryption, crc, mic ,etc.
- Number of MSDUs dropped in the driver
- A-MPDU/A-MSDU subframe stats
- Number of MSDUS passed to mac80211
All stats other than A-MPDU stats are only for received data frames.
A-MPDU stats might have stats for management frames when monitor
interface is active where management frames are notified both in wmi
and HTT interfaces.
These per tid stats can be enabled with tid bitmask through a debugfs
like below
echo <tid_bitmask> > /sys/kernel/debug/ieee80211/phyX/ath10k/sta_tid_stats_mask
tid 16 (tid_bitmask 0x10000) is used for non-qos data/management frames
The stats are read from
/sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/<sta_mac>/dump_tid_stats
Sample output:
To enable rx stats for tid 0, 5 and 6,
echo 0x00000061 > /sys/kernel/debug/ieee80211/phy0/ath10k/sta_tid_stats_mask
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan15/stations/8c\:fd\:f0\:0a\:8e\:df/dump_tid_stats
Driver Rx pkt stats per tid, ([tid] count)
------------------------------------------
MSDUs from FW [00] 2567 [05] 3178 [06] 1089
MSDUs unchained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:chained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:filtered [00] 0 [05] 0 [06] 0
MSDUs queued for mac80211 [00] 2567 [05] 3178 [06] 1089
MSDUs with error:fcs_err [00] 0 [05] 0 [06] 2
MSDUs with error:tkip_err [00] 0 [05] 0 [06] 0
MSDUs with error:crypt_err [00] 0 [05] 0 [06] 0
MSDUs with error:peer_idx_inval [00] 0 [05] 0 [06] 0
A-MPDU num subframes upto 10 [00] 2567 [05] 3178 [06] 1087
A-MPDU num subframes 11-20 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 21-30 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 31-40 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 41-50 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 51-60 [00] 0 [05] 0 [06] 0
A-MPDU num subframes >60 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 1 [00] 2567 [05] 3178 [06] 1089
A-MSDU num subframes 2 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 3 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 4 [00] 0 [05] 0 [06] 0
A-MSDU num subframes >4 [00] 0 [05] 0 [06] 0
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some functions definitions have either the initial open brace and/or
the closing brace outside of column 1.
Move those braces to column 1.
This allows various function analyzers like gnu complexity to work
properly for these modified functions.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJatkBHAAoJEG4XJFUm622bKuwH/1cPOfTDDd/kFdRSht0rkj0J
PJ+OxdlbnPuXU7R9juDo5r3WeNoyiXvsdKNYGchn9XIEq2BN1jzOzcE7FYs1IwKs
UPZ6gUgF4+wD5eL1tmiWd+P8CSMVVYAdUGE+CjXOdUT08s5NsIm4Uv86ry/nm7gI
DkrkdlRjqDb6Dx8M35kX9AguR1QHz2KmOu2htPomHzDONrD99z8FaqZQHg4oyNAX
yIvidDcDRYmMoHfkifJiuuUxnRgD935tM6QECYjGKXLnCDb9KklCaabe77lAH39M
EGI7Z6teZrvv5IozpGgPnUjr+hjgoiXxfQmFyXOZAmuSDHbxudYMfOd7KtQ18W0=
=ySDb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching mac80211 to use QoS NDP, it turned out that
ath9k_htc is somehow broken by this, e.g. see
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=891060.
Fix this by using the new mac80211 flag to go back to the
old, incorrect, behaviour for this driver.
Fixes: 7b6ddeaf27 ("mac80211: use QoS NDP for AP probing")
Reported-by: Ben Caradoc-Davies <ben@transient.nz>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When ath9k was switched over to use the mac80211 intermediate queues,
node cleanup now drains the mac80211 queues. However, this call path is
not protected by rcu_read_lock() as it was previously entirely internal
to the driver which uses its own locking.
This leads to a possible rcu_dereference() without holding
rcu_read_lock(); but only if a station is cleaned up while having
packets queued on the TXQ. Fix this by adding the rcu_read_lock() to the
caller in ath9k.
Fixes: 50f08edf98 ("ath9k: Switch to using mac80211 intermediate software queues.")
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 sends mgmt frames by reference via WMI.
The host dma maps the mgmt frame and sends the physical
address to the firmware in the wmi command. Since the
dma mapping is done in the gen_mgmt_tx and if the wmi
command send fails, the corresponding mgmt frame is
not being dma unmapped.
Fix the missing dma unmapping of mgmt tx frame when
wmi command sending fails for mgmt tx by reference
via WMI. The already exisiting mgmt tx using copy by
value does not need such dma unmapping.
Add a separate wmi-tlv op for mgmt tx via ref, which
takes care of unmapping the dma address, in case of
wmi command sending failure.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lots of the wireless driver vendor Kconfig symol help text says
"questions about cards." (2 spaces between "about" and "cards")
Besides dropping one of those spaces, it also needs some other word
inserted there. Instead of putting each vendor's name there, I chose
to say "these" cards in all of the Kconfig help text.
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added a new debugfs file 'mids' to print the list of
virtual interfaces by MAC ID (MID). Allows mapping
between the internal MID used by FW and the actual
network interface used by the VIF. This is needed by
debugging tools.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Track the connection status per-VIF.
The data path code is also updated to support multiple VIFs.
This includes RX and TX VRING management, NAPI poll loops,
RX reordering and related code.
Power management code used to check if the main interface
is up or based on connection state of the main interface,
adapt this code to take all VIFs into account.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As more support is added for multiple VIFs, there is a need
to protect the wil6210_vif structure from access while it is
deleted (mainly from del_virtual_intf operation).
Instead of adding another mutex, use p2p_wdev_mutex and rename
it to vif_mutex to reflect the added role. Its existing roles
are similar so it extends nicely (for example it protects the
scan_request member which is also a member of wil6210_vif).
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for multiple VIFs in the cfg80211 operations start_ap,
stop_ap and change_beacon. This change allows starting multiple APs
using virtual interfaces.
The data path and most other operations are still working only
on the main interface.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add generic support in cfg80211 operations add_virtual_intf
and del_virtual_intf for adding/removing VIFs of any
interface type, and fix change_virtual_intf to allow changing
the interface type of a VIF. Previously these operations
only worked for the P2P_DEVICE interface which is not a real
VIF(it is management-only and shares radio with the main
interface).
Currently the interface combination is validated, the VIF is
added/removed in the firmware and the appropriate net/wireless
device is also added/removed.
Added minimal support for proper interface up/down and module
unload but most operations still work only on the main interface.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simple infrastructure changes for supporting multiple
virtual interfaces (multiple VIFs).
It is still not possible to add new VIFs so the only VIF
belongs to the main interface.
Main changes:
1. Add MAC ID(mid) argument to wmi_send and wmi_call to
allow invoking WMI commands on different VIFs.
2. Similarly, in WMI event handler look at the mid reported
by FW and extract VIF structure (currently only for main
interface). All WMI event handlers operate on wil6210_vif
structure so they know on which VIF they were called.
3. Trivial changes to use wil6210_vif structure and MID
throughout the code.
4. Various changes to logging to report MID.
More complete multiple VIFs support will be added gradually
in next patches.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New FW which supports multiple virtual interfaces, reports
its allowed interface combinations using a special comment
record in the FW file. The format of the interface combinations
is similar to the kernel wiphy->iface_combinations.
When parsing FW file during module initialization, also parse
and validate the concurrency record, and initialize
wiphy->n_iface_combinations and wiphy->iface_combinations
accordingly.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For supporting multiple virtual interfaces in the future,
introduce a wil6210_vif structure which will hold per-VIF
data. Change the module initialization so wil6210_vif will
be part of net_device structure, and wireless_dev will be
embedded inside the wil6210_vif structure. This will allow
us to find the appropriate wil6210_vif structure when we
only have access to wireless_dev or net_device.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The wcn36xx_cancel_hw_scan method stops the hw scan and notify the
scan completion via ieee80211_scan_completed.
However, on scan offload cancellation, firmware sends a scan complete
indication, triggering a new call to ieee80211_scan_completed.
This leads to kernel warn since the scan has already been completed.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ack timing generation has to be adapted for 5/10 MHz channels.
Do it by properly initializing ack shift field in TXSIFS
register. Ack shift assumes channel width of 2.5 Mhz so
value zero means 2.5 MHz, 1 is 5 MHz and so on.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The bitrate value for airtime calculation is specified for
full rates. We need to divide it for 5 and 10MHz channels to
get correct result.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer tq is initialized with &ah->ah_txq[queue] and then a few
lines later is re-assigned the same value, hence this duplicate
assignment is redundant and can be removed.
Cleans up clang warning:
drivers/net/wireless/ath/ath5k/qcu.c:326:25: warning: Value stored
to 'tq' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preparation for a new QCA9377 firmware release. The new firmware release
requires more IRAM banks, hence update that on ath10k.
The IRAM banks promotion won't break any backwards compatibility, as those IRAM
banks were not getting used in previous firmware releases.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HIF power-on failure is applicable to each underlying
bus type. Fix log message for hif power on failure.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in debug error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever ath10k firmware discards a packet (HTT_TX_COMPL_STATE_DISCARD
flag), the skb is freed and mac80211 does not get feedback through
ieee80211_tx_status().
Instead, make sure that the IEEE80211_TX_STAT_ACK flag is disabled and
let the packet go through, like ath9k does.
Signed-off-by: Ignacio Nunez Hernanz <nacho.nunez@aoifes.com>
[kvalo@codeaurora.org: rebase patch manually]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One thing to note: I've included a new ethertype
that wireless uses (ETH_P_PREAUTH) in if_ether.h.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAlqPJKcACgkQB8qZga/f
l8TAUw/7BMKG4ofFYRgujmqS+mnSDJx9vgtFHIV3Ymcm9vgdQ6wbNe85ME8J6TpN
Z/HqtWVhn7BEWqpiDgq0ADTEmU/Vt6AQvy6fJX80+Lz4yup8Dq9dI9/CJ7BlKP+t
O7/jXkv2RykFv1IAG9US3Xx9rIwLJRP6XndksZMsK4QihdUYOqAqjZ+pLWCHQ7+a
vFewlUV6t7IMq3R9scL4nf5EmgLWNDNCSOZ6xWDxfDgLHsErbCD9ojRsfAnQWPN0
1rwPC5kGm9tzGtiPVhA0/a4D0dgiYdv723ubs/waSYX5fimXDPSXsRizVp06ZWC+
lFW+Mw52WvxriO61MD99xH1O1/svy+YMMgECoPMjGk7QzgY+2xQ/8hUbo91fsj07
05+rGX3O0SJvB0une3m3ZsZz00DkZDU4Fw0kvO0aSCmE++O4vt/04wmMWxGVfnSo
RtdrQNSAYrYqHSc+1kIzDAH2jCBBLj0cWdlZPYciYMTRUHOFZmMApyyXVLoOl3yn
eqLgK8QBNpkjkf5FbF+m0ccHtQ8lkKiZDcqqIVN+dxKuuO9FEfblDty5bZEp8AaT
Q2soararYeUcNVA2A+Gi1l3qtcj+wWay+CdDcU/QmYbXoxdRh64FBs//y6akIH9p
p/cNgRP/MyEUEkvGmpva+MdtzCToWR4Asm4eErlsvvbIvKEFjPI=
=A6XK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates across wireless.
One thing to note: I've included a new ethertype
that wireless uses (ETH_P_PREAUTH) in if_ether.h.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support to get ack signal in probe client response
and in station info from user.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
[squash in compilation fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 8da58553cc ("ath9k: Use calibrated noise floor value
when available") introduced regression in ath9k_hw_getchan_noise
where per chain nominal noise floor has been taken instead default
for channel.
Revert to original default channel noise floor.
Fixes: 8da58553cc ("ath9k: Use calibrated noise floor value when available")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some modern Ubiquiti devices contain a rebranded QCA988X rev2 with
a custom Ubiquiti vendor and device id. This patch adds support for
those devices, treating them as a QCA988X v2.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[kvalo@codeaurora.org: rebase, add missing fields in hw_params, fix a long line in pci.c:61]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The length of DRAM dump for QCA6174 hw3.0/hw3.2 and QCA9377 hw1.1
are less than the actual value, some coredump contents are missed.
To fix it, change the length from 0x90000 to 0xa8000.
Fixes: 703f261dd7 ("ath10k: add memory dump support for QCA6174/QCA9377")
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx_dxe_init() doesn't check for the return value of
wcn36xx_dxe_init_descs(), release the resources in case an error ocurred.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 series allows to calibrate noise floor for different frequency
bins. Once it's done it's possible to get more accurate rssi/signal
values over whole frequency band at a given temperature.
The RSSI/signal accuracy reported by calibrated RF cards improves
from 6 to up to 2dB.
This could be interesting for application which require good signal
accuracy like roaming or mesh protocols.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 devices can have calibrated noise floor values
which can be used instead of hard coded one. Read them
from eeprom and save interpolated value in nf limits for
the current channel.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 factory calibration allows to use bigger EEPROM than
standard 1k without changing the default layout. Allow
probing of EEPROM at alternative address if initial check
for default fails.
The original ar9003 eeprom ops are still be used.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to allow using the same brd file across different
11ad chips, the address for loading the brd file should be
part of the FW file, instead of the brd file. The brd file is
expected to include only one section.
To allow backward compatibility the driver reads the
address from the brd file in case it is not included in the
FW file.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sparrow D0 chips have slightly larger mac_rgf_ext section
in order to support extra features such as multiple virtual
interfaces.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when we want to bring the interface up, we first
reset the device which causes the boot loader to run. Then
we halt the device CPU, load FW image and resume the device
CPU.
There are some boot loader versions which perform redundant
memory accesses even when idle. Halting the device CPU
while boot loader access memory can cause the device memory
controller to get stuck, the FW will fail to load and the
network interface will not come up.
For such boot loaders implement a workaround where we freeze
the boot loader before halting the device CPU, so it will not
perform any memory accesses.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
OTP HW vectors values are different for 40MHz and 330MHz AHB
clocks.
In SW reset flow, the host driver sets the clock frequency
to 40MHz. In order to allow reading from the OTP, the host
driver should configure the OTP HW vectors with the values
that fits this clock frequency.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn device supports boot without flash.
Driver detects flashless device and in this case waits for ready indication
from HW machine (instead of bootloader ready indication). Also in this
case, MAC address is retrieved from OTP.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn memory has changed, areas were increased and shifted
to new locations.
Use the appropriate address map according to the device JTAG ID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add Talyn JTAG ID to the list of valid IDs
and identify this device as Talyn.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PCIe device ID has changed in Talyn.
Add this ID to wil6210_pcie_ids list to allow
recognition of Talyn device.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch found these issues:
drivers/net/wireless/ath/ath10k/ce.h:324: Please use a blank line after function/struct/union/enum declarations
drivers/net/wireless/ath/ath10k/core.c:1321: Please don't use multiple blank lines
drivers/net/wireless/ath/ath10k/htt.h:1859: Please use a blank line after function/struct/union/enum declarations
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable section_table.size is a u32 and so cannot be less than
zero, hence the less than zero check is redundant and can be
removed.
Detected by CoverityScan, CID#1463855 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in warning message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Validate ie_len after the alignment padding before access the buffer
to avoid potential overflow.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some platform(BIOS) blocks legacy interrupts (INTx), and only allows MSI
for WLAN device. So adding a quirk to list those machines and set
use_msi automatically.
Adding the following platforms to the quirk.
Dell Inspiron 24-3460
Dell Inspiron 3472
Dell Inspiron 14-3473
Dell Vostro 3262
Dell Vostro 15-3572
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On new Intel platforms like ApolloLake, legacy interrupt mechanism
(INTx) is not supported, so WLAN modules are not working because
interrupts are missing, therefore this patch is to add MSI support to
ath9k. With module paremeter "use_msi=1", ath9k driver would try to
use MSI instead of INTx.
Signed-off-by: Russell Hu <rhu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaWd2WAAoJEG4XJFUm622bDnsH/2+Y5MEn31xvv7FGP46dHCNB
wk1SgcQOQdb7taIpZ++tFvhTQOXwrtGMA5iAFLeg9+07tqGIaZQqr58aab7BCQTi
2PgUK9sEdI5LPw3KmhnaqfHMVDKMaYdjcAhLG4FzJqMoDfTuPr56Vnnde3J2A0mj
hhFRarNKBArEvRaWtNypdZQN8HM10v3LJq+HNnK/yep7fW2EuwSwTO2YBqDhrwAD
0gzfV6yi05497uVv6W+5CKRawu7RoYgbFTaEa8rmCViIjf9bK4gPdsW18a/DTNMz
MfvLF2RQZk1k944+a+a983oqZNkq9dEWd0kF0CSFgbO3r/SO7264yc4PHpZKy/s=
=2eQ4
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
The second assignment to msg_body.min_ch_time is incorrect, it
should actually be to msg_body.max_ch_time.
Thanks to Bjorn Andersson for identifying the correct way to fix
this as my original fix was incorrect.
Detected by CoverityScan, CID#1463042 ("Unused Value")
Fixes: 2f3bef4b24 ("wcn36xx: Add hardware scan offload support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was accidentally left out from the switch statement and target info was not
queried.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[kvalo@codeaurora.org: add commit log]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function does not exist and thus, the prototype can be removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field preset_chandef of wireless_dev must not be accessed
by the driver because it is private to cfg80211. Store the
monitor channel locally in wil6210_priv instead.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"FIXME: IRQ mask debug" and "FIXME: interrupts enabled - for debug"
can be removed because wil6210_debug_irq_mask() is now considered
production feature.
"FIXME FW can transmit only ucast frames to peer" and "FIXME real
ring_id instead of hard coded 0" can be removed because FW/HW already
support multicast transmission.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Suspend and crash dump operations can happen simultaneously
in case there is a FW assert during the suspend procedure
or when SSR calls all the devices crashdump callbacks.
To prevent that, a new flag is added, indicating that the
dumps collection is in progress, in order to allow the
suspend/reset decline if the dumps collection already started.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some cases the platform should be aware of the FW capabilities
to decide which feature to enable.
For example, FW can control the external REF clock for power saving.
Driver should notify the platform about that, to allow platform
power management optimization.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add get_capa callback to platform ops to allow reading the platform
capabilities.
Supported capabilities:
- Keeping 11ad connection during suspend
- T_POWER_ON 0 support
- Usage of external clock
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the option to support 40bit addresses since some platforms
may not support 48bits but support 40bits
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for sched_scan_start/stop by sending PNO commands to FW.
Driver reports max_sched_scan_reqs and invokes
cfg80211_sched_scan_results upon receiving WMI_SCHED_SCAN_RESULT_EVENTID
from FW.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since driver does not report hardware dynamic power saving cap,
this is up to the mac80211 to manage power saving timeout and
state machine, using the ieee80211 config callback to report
PS changes. This patch enables/disables PS mode according to
the new configuration.
Remove old behaviour enabling PS mode in a static way, this make
the device unusable when power save is enabled since device is
forced to PS regardless RX/TX traffic.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add memory dump to the firmware crash data file which is provided to user space
via devcoredump interface. This makes it easier for firmware engineers to debug
firmware crashes.
Due to increased memory consumption the memory dump is disabled by default. To
enable it make sure that bit 3 is set in coredump_mask module parameter:
modprobe ath10k_core coredump_mask=0xffffffff
When RAMDUMP is enabled a buffer for the dump is allocated with vmalloc during
device probe. The actual memory layout is different in hardware versions and
the layouts are defined in coredump.c. The memory is split to regions and, to
get even finegrained control of what to copy, the region can split to smaller
sections as not all registers are readable (which could cause the whole system
to stall).
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: refactoring and cleanup]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For memory dump support (it consumes quite a lot of memory) we need to control
what is exactly stored to the crash dump. Add a module parameter call
coredump_mask to do that. It's a bit mask of these values:
enum ath10k_fw_crash_dump_type {
ATH10K_FW_CRASH_DUMP_REGISTERS = 0,
ATH10K_FW_CRASH_DUMP_CE_DATA = 1,
ATH10K_FW_CRASH_DUMP_MAX,
};
For example, if we only want to store CE_DATA we would enable bit 2:
modprobe ath10k_core coredump_mask=0x2
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now coredump is totally separate from debug.c and doesn't depend on
CONFIG_ATH10K_DEBUGFS anymore, only on CONFIG_DEV_COREDUMP. Also remove
leftovers from the removed debugfs file support.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation to add RAM dump support. No functional changes, only moving code
and renaming function names.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The fw_crash_dump file was deprecated by commmit 727000e6af ("ath10k: support
dev_coredump for crash dump") in v4.11 in favor of dev_coredump interface,
remove it now for good. Everyone should use dev_coredump now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable TDLS wider bandwidth support for 5GHz based on firmware wmi capabilities.
This patch is required for chipset QCA9888. Tested with firmware version
10.4-3.5.1-00018.
Signed-off-by: Balaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HL1.0 firmware is not loaded via bmi. The bmi specific
code should not be executed for HL1.0
Add fw feature flag for non bmi targets and skip the bmi
specific code for non bmi targets.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 is integrated chipset which uses system NOC.
Add SNOC bus type and related definitions.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 CE descriptor uses 64bit address for
src/dst ring buffer. It has extended field for toeplitz
hash result, which is being used for HW assisted
hash results.
To accommodate WCN3990 descriptor, define new CE
descriptor for extended addressing mode and related
methods to handle the descriptor data.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE send and receive API's are using u32 ring address, which
truncates the address for target with 64bit addressing range.
Use dma_addr_t for ce buffers to support target with extended
addressing range.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
paddrs_ring_64 holds the physical device address of the
rx buffers that host SW provides for the MAC HW to fill.
Since this field is used in rx ring setup and rx ring
replenish in rx data path. Define separate methods
for handling 64 bit ring paddr and attach them dynamically
based on target_64bit hw param flag. Use u64 type
while popping paddr from the rx hash table for 64bit target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 uses larger ring size in comparison to existing
ring size value.
Add rx ring size hw param for supporting different rx ring
size across multiple target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target uses 64 bit frags_paddr in htt tx descriptor,
which holds the physical address of SKB fragments in tx data path.
In order to support 64 bit bit frags_paddr in htt tx descriptor, define
htt_data_tx_desc_64 descriptor and ath10k_htt_tx_64 method for handling
tx data path with new descriptor fields.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target uses 64 bit frag descriptor and more
fields in TSO flag.
Add support for 64 bit HTT frag descriptor.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3900 target uses 64bit rx_ring_base_paddr and
fw_idx_shadow_reg_paddr fields in HTT rx ring cfg message.
These address points to the memory region where remote
ring empty buffers are allocated.
In order to add 64 bit htt rx ring cfg, define separate
64 bit htt rx ring cfg message and attach it in runtime
based on target_64bit hw param flag.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target use 64bit msdu address in htt in-order
indication message. Add support for 64 bit msdu address in
HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND message.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 rx descriptor uses different offset of msdu start, msdu end,
ppdu end, rx pkt end and rx frag info.
To accommodate different offsets, define respective fields in
rx descriptor of WCN3990 target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target supports 37-bit addressing mode. In order
to accommodate extended address support, add hw param to
indicate if the target supports addressing above 32-bits.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The #ifdef checks are hard to get right, in this case some functions
should have been left inside a CONFIG_PM_SLEEP check as seen by this
message:
drivers/net/wireless/ath/wil6210/pcie_bus.c:489:12: error: 'wil6210_pm_resume' defined but not used [-Werror=unused-function]
drivers/net/wireless/ath/wil6210/pcie_bus.c:484:12: error: 'wil6210_pm_suspend' defined but not used [-Werror=unused-function]
Using an __maybe_unused is easier here, so I'm replacing all the
other #ifdef in this file as well for consistency.
Fixes: 94162666cd ("wil6210: run-time PM when interface down")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Variable fc is being assigned but never used, so remove it. Cleans
up the clang warning:
warning: Value stored to 'fc' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add hw params entry for wcn3990 and populate various
target specific values for wcn3990.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The parameter values for skid limit, number of peers and wds
entries values which are sent in wmi init cmd are hardware
specific.
Add support to obtain skid limit, number of peers and wds entries
values from hw params which will have the hw specific values
for these parameters.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HL1.0 firmware branch, used in wcn3990, transmits management
frames by reference over WMI.
Add support for management tx by reference over WMI.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to the limitation of wmi tlv parsing logic, if there are
two parameters in a wmi event with same tlv tag, we can get only
the last value, as it overwrites the prev value of the same tlv tag.
The service ready event in wcn3990 contains two parameters of the
same tag UINT32, due to which the svc bitmap is overwritten with the
DBS support parameter.
Refactor the service ready event parsing to allow parsing two tlv
of the same tag UINT32 for wcn3990.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The purpose of pushing indication on a list and handle these in a
separate worker is to allow the handlers to sleep. It does therefor not
make much sense to hold the queue spinlock through the entire indication
worker function.
By removing items from the queue early we don't need to hold the lock
throughout the indication worker, allowing the individual handlers to
sleep.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch generates a warning here:
drivers/net/wireless/ath/ath9k/htc_drv_main.c:1688 ath9k_htc_ampdu_action()
error: buffer overflow 'ista->tid_state' 8 <= 15
I don't know if it's a real bug or not but the other paths through this
function all ensure that "tid" is less than ATH9K_HTC_MAX_TID (8) so
checking here makes things more consistent.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current hw_scan implementation does not trigger offloaded
hardware scan and seems to only put the device in a kind of
listening mode (beacon/probe-response) for software scan.
Since no probe request are generated by the software, current
scanning method is similar to a passive scan.
This patch introduces support for 'true' hardware offloaded scan.
Hardware scan is configured and started via the start-scan-offload
firmware message. Once scan has been completed a scan indicator
message is received from firmware.
Moreover, this patch includes support for directed probe-request,
allowing connection with hidden APs. It also fixes scan issues with
band-steering AP which are not 'visible' with passive scan (due to
hidden ssid in beacons).
Let's keep the 'legacy' scanning method in case scan-offload is not
supported.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4 firmware branch (used in QCA988X) does not support
HTT_10_4_T2H_MSG_TYPE_PEER_STATS and that's why ath10k does not provide
tranmission rate statistics to user space, instead it just shows
hardcoded 6 Mbit/s. But pktlog firmware facility provides per peer tx
statistics. The firmware sends one pktlog event for every four
PPDUs per peer, which include:
* successful number of packets and bytes transmitted
* number of packets and bytes dropped
* retried number of packets and bytes
* rate info per ppdu
Firmware supports WMI_SERVICE_PEER_STATS, pktlog is enabled through
ATH10K_FLAG_PEER_STATS, which is nowadays enabled by default in ath10k.
This patch does not impact throughput.
Tested on QCA9880 with firmware version 10.2.4.70.48. This should also
work with firmware branch 10.2.4-1.0-00029
Parse peer stats from pktlog packets and update the tx rate information
per STA. This way user space can query about transmit rate with iw:
$iw wlan0 station dump
Station 3c:a9:f4:72:bb:a4 (on wlan1)
inactive time: 8210 ms
rx bytes: 9166
rx packets: 44
tx bytes: 1105
tx packets: 9
tx retries: 0
tx failed: 1
rx drop misc: 3
signal: -75 [-75, -87, -88] dBm
signal avg: -75 [-75, -85, -88] dBm
tx bitrate: 39.0 MBit/s MCS 10
rx bitrate: 26.0 MBit/s MCS 3
rx duration: 23250 us
authorized: yes
authenticated: yes
associated: yes
preamble: short
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 22 seconds
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move pktlog_filter from struct ath10k_debug to struct ath10k
so that pktlog can be enabled even when debugfs is not
enabled, needed to enable peer tx stats for 10.2.4.
No changes in functionality.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove CONFIG_MAC80211_DEBUGFS dependency on ath10k_sta_statistics().
ath10k_sta_statistics() has per sta tx/rx stats and this should not
be dependent on MAC80211_DEBUGFS.
No changes in functionality.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With current NAPI implementation, NAPI poll can deliver more frames
to net core than allotted budget. This may cause warning in napi_poll.
Remaining quota is not accounted, while processing amsdus in
rx_in_ord_ind and rx_ind queue. Adding num_msdus at last can not
prevent delivering more frames to net core. With this change,
all amdus from both in_ord_ind and rx_ind queues are processed and
enqueued into common skb list instead of delivering into mac80211.
Later msdus from common queue are dequeued and delivered depends on
quota availability. This change also simplifies the rx processing in
napi poll routine.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Data packets are not sent by STA in case of STA joined to
non QOS AP (WMM disabled AP). This is happening because of STA
is sending data packets to firmware from host with qos enabled
along with non qos queue value(TID = 16).
Due to qos enabled, firmware is discarding the packet.
This patch fixes this issue by updating the qos based on station
WME capability field if WMM is disabled in AP.
This patch is required by 10.4 family chipsets like
QCA4019/QCA9888/QCA9884/QCA99X0.
Firmware Versoin : 10.4-3.5.1-00018.
For 10.2.4 family chipsets QCA988X/QCA9887 and QCA6174 this patch
has no effect.
Signed-off-by: Balaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.4 firmware defines this as a 3-bit field, as does the
mac80211 stack. The 4th bit is defined as CONF_IMPLICIT_BF
at least in the firmware header I have seen. This patch
fixes the ath10k wmi header to match the firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace ntohs with be16_to_cpu to do endian conversions for ethhdr
h_proto assignment.
Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
At the moment, spectral scan support, and with it RELAY, is always enabled
with ATH10K_DEBUGFS. Spectral scan support is currently the only user of
RELAY in ath10k, and it unconditionally reserves a relay channel.
Having debugfs support in ath10k is often useful even on very small
embedded routers, where we'd rather like to avoid the code size and RAM
usage of the relay support. While ath10k-based devices usually have more
resources than ath9k-based ones, it makes sense to keep the configuration
symmetric to ath9k, so the same base kernel without RELAY can be used for
both ath9k and ath10k hardware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
At the moment, spectral scan support, and with it RELAY, is always enabled
with ATH9K[_HTC]_DEBUGFS. Spectral scan support is currently the only user
of RELAY in ath9k, and it unconditionally reserves a relay channel.
Having debugfs support in ath9k is often useful even on very small embedded
routers, where we'd rather like to avoid the code size and RAM usage of the
relay support.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dump format uses 64-bit timestamps already, but calling
getnstimeofday() only returns a 32-bit number on 32-bit architectures,
so that will overflow in y2038.
This changes it to use ktime_get_real_ts64() instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To get rid of W=1 warning: variable ‘ies_len’ set but not used.
Variable ies_len is being assigned but never read.
Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the value for the firmware configuration parameters
BTC_STATIC_LEN_LE_BT and BTC_STATIC_LEN_LE_WLAN are not set the duty
cycle between BT and WLAN is such that if BT (including BLE) is active
WLAN gets 0 bandwidth. When tuning these parameters having a too high
value for WLAN means that BLE performance degrades.
The "sweet" point of roughly half of the maximal values was empirically
found to achieve a balance between BLE and Wi-Fi coexistence
performance.
Signed-off-by: Eyal Ilsar <eilsar@codeaurora.org>
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the statistics show how many successful/failed
suspend/resume operations the system had.
Update the statistics by splitting each successful/failed
suspend/resume operations to radio on/off.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently suspend time statistics are showed through debugfs.
Remove time statistics in suspend state since the timing may
not be accurate in that state.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of interface down, radio is turned off but PCIe mastering is
not cleared.
This can cause unexpected PCIe access to the shutdown device.
Fix this by clearing PCIe mastering also in case interface is down
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a length check in wil_cfg80211_mgmt_tx to detect unsigned integer
overflow.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a length check in wmi_set_ie to detect unsigned integer
overflow.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When loading FW from file add block size checks to ensure a
corrupted FW file will not cause the driver to write outside
the device memory.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The current length check:
sizeof(cmd) + len > r->entry_size
will allow very large values of len (> U16_MAX - sizeof(cmd))
and can cause a buffer overflow. Fix the check to cover this case.
In addition, ensure the mailbox entry_size is not too small,
since this can also bypass the above check.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On-going operations were not aborted properly
and required locks were not taken.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW capabilities are currently retrieved only during module
initialization, but userspace can replace the firmware while
interface is down, so refresh the FW capabilities when
interface is up (after FW is loaded) to ensure driver
functionality matches the loaded FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon sending/receiving WMI commands/events, print human readable
names in addition to id for easier debugging.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow run-time suspend when interface is down, keep card alive when
interface is up.
If driver is in wmi only or debug_fw mode run-time PM won't suspend.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Handle tdls peer events from the target. TDLS events for the peer
could be discover, teardown, etc. As of now, adding the logic to
handle tdls teardown events alone.
Teardown due to peer traffic indication(PTR) timeout is one such
teardown event from the target.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is required to update the teardown state of the peer when
a tdls link with that peer is terminated. This information is
useful for the target to perform some cleanups wrt the tdls peer.
Without proper cleanup, target assumes that the peer is connected and
blocks future connection requests, updating the teardown state of the
peer addresses the problem.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 4ca1807815 ("ath10k: disable wake_tx_queue for older devices")
disables the use of the mac80211 TXQs for some devices because of a theoretical
throughput regression. The original regression report[1] was related to
fq_codel qdisc drop performance, which was fixed in commit 9d18562a22
("fq_codel: add batch ability to fq_codel_drop()"). Since then, we have not
seen the TXQ-related regression, so it should be safe to re-enable TXQs.
[1] http://lists.infradead.org/pipermail/ath10k/2016-April/007266.html
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make use of the swap macro and remove unnecessary variable temp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* CRYPTO_SHA256 is needed for regdb validation
* mac80211: mesh path metric was wrong in some frames
* mac80211: use QoS null-data packets on QoS connections
* mac80211: tear down RX aggregation sessions first to
drop fewer packets in HW restart scenarios
-----BEGIN PGP SIGNATURE-----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=ODX1
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-11-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Four fixes:
* CRYPTO_SHA256 is needed for regdb validation
* mac80211: mesh path metric was wrong in some frames
* mac80211: use QoS null-data packets on QoS connections
* mac80211: tear down RX aggregation sessions first to
drop fewer packets in HW restart scenarios
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When connected to a QoS/WMM AP, mac80211 should use a QoS NDP
for probing it, instead of a regular non-QoS one, fix this.
Change all the drivers to *not* allow QoS NDP for now, even
though it looks like most of them should be OK with that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mmio node was also prematurely freed.
Fixes: fd52bdae9a ("wcn36xx: Disable 5GHz for wcn3620")
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure 16-byte mic is removed from the rx data packet
tail when CCMP-256, GCMP and GCMP-256 ciphers are used
in raw decap mode. This fixed rx traffic failures in those
ciphers in raw mode. Split the helper returning crypto
tail length into two, one to get the ICV length and other
to get the mic lengh for the cipher to make it clean.
Fixes: 2ea9f12cef ("ath10k: add new cipher suite support")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
=MvWY
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <davem@davemloft.net>
Thorsten reported on <fa6e3ee2-91b5-a54b-afe3-87f30aac7a48@leemhuis.info> that
commit c9353bf483 made ath10k unstable with QCA6174 on his Dell XPS13 (9360)
with an error message:
ath10k_pci 0000:3a:00.0: failed to extract amsdu: -11
It only seemed to happen with certain APs, not all, but when it happened the
only way to get ath10k working was to switch the wifi off and on with a hotkey.
As this commit made things even worse (a warning vs breaking the whole
connection) let's revert the commit for now and while the issue is being fixed.
Link: http://lists.infradead.org/pipermail/ath10k/2017-October/010227.html
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx data frames notified through HTT_T2H_MSG_TYPE_RX_IND and
HTT_T2H_MSG_TYPE_RX_FRAG_IND expect PN/TSC check to be done
on host (mac80211) rather than firmware. Rebuild cipher header
in every received data frames (that are notified through those
HTT interfaces) from the rx_hdr_status tlv available in the
rx descriptor of the first msdu. Skip setting RX_FLAG_IV_STRIPPED
flag for the packets which requires mac80211 PN/TSC check support
and set appropriate RX_FLAG for stripped crypto tail. Hw QCA988X,
QCA9887, QCA99X0, QCA9984, QCA9888 and QCA4019 currently need the
rebuilding of cipher header to perform PN/TSC check for replay
attack.
Please note that removing crypto tail for CCMP-256, GCMP and GCMP-256 ciphers
in raw mode needs to be fixed. Since Rx with these ciphers in raw
mode does not work in the current form even without this patch and
removing crypto tail for these chipers needs clean up, raw mode related
issues in CCMP-256, GCMP and GCMP-256 can be addressed in follow up
patches.
Tested-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No rcu_read_lock is called, but rcu_read_unlock is still called.
Thus rcu_read_unlock should be removed.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This driver shouldn't be using wdev->ssid to start with, as
it's more or less an internal field in cfg80211 used for
various purposes. Reading it is possible through nl80211,
even if that's not really what we should be doing there
for anything but AP type interfaces.
It *really* shouldn't allow modifying it!
Remove the whole debugfs entry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Variable val is unsigned, so checking whether it is less than zero is
redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Variable val is unsigned, so checking whether it is less than zero is
redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The current firmware 10.4-3.5.1-00035 on QCA9888 supports
TDLS explicit mode, it expects WMI_TDLS_ENABLE_PASSIVE
for tdls setup and WMI_TDLS_DISABLE for tdls teardown.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Do not allow off channel operations like scans/roc when
there are active TDLS sessions.
The Current firmware 10.4-3.5.1-00035 on QCA9888 does not
supports any offchannel operations on active TDLS sessions,
either driver needs to block the offchannel operation requests
or should teardown the TDLS connection.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To be able to use ath10k_mac_tdls_vif_stations_count() in
ath10k_hw_scan() in the following patch, move the functions
earlier in the file.
This commit is pure code move, no functional changes.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Build errors have been reported with CONFIG_PM=n:
drivers/net/wireless/ath/ath10k/pci.c:3416:8: error: implicit
declaration of function 'ath10k_pci_suspend'
[-Werror=implicit-function-declaration]
drivers/net/wireless/ath/ath10k/pci.c:3428:8: error: implicit
declaration of function 'ath10k_pci_resume'
[-Werror=implicit-function-declaration]
These are caused by the combination of the following two commits:
6af1de2e4e ("ath10k: mark PM functions as __maybe_unused")
96378bd2c6 ("ath10k: fix core PCI suspend when WoWLAN is supported but
disabled")
Both build fine on their own.
But now that ath10k_pci_pm_{suspend,resume}() is compiled
unconditionally, we should also compile ath10k_pci_{suspend,resume}()
unconditionally.
And drop the #ifdef around ath10k_pci_hif_{suspend,resume}() too; they
are trivial (empty), so we're not saving much space by compiling them
out. And the alternatives would be to sprinkle more __maybe_unused, or
spread the #ifdef's further.
Build tested with the following combinations:
CONFIG_PM=y && CONFIG_PM_SLEEP=y
CONFIG_PM=y && CONFIG_PM_SLEEP=n
CONFIG_PM=n
Fixes: 96378bd2c6 ("ath10k: fix core PCI suspend when WoWLAN is supported but disabled")
Fixes: 096ad2a15fd8 ("Merge branch 'ath-next'")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.15. Major changes:
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
there it's supported (QCA99x0 and QCA4019)
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This way, we can apply the values when the NIC does come up.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When the user sets count to zero the string buffer would remain
completely uninitialized which causes the kernel to parse its
own stack data, potentially leading to an info leak. In addition
to that, the string might be not terminated properly when the
user data does not contain a 0-terminator.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Reviewed-by: Christoph Böhmwalder <christoph@boehmwalder.at>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99x0 and QCA4019 family chips support CCMP-256, GCMP-128, and
GCMP-256 ciphers in hardware, so advertise support for these. As
firmware does not support group management frame ciphers (BIP),
handle them in software (mac80211).
Reviewed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath10k host enables power save support in station mode by
default for all firmwares but Power save for station mode still not supported
in some of the firmware versions. Which results in firmware crash while
issueing multiple scan commands.
Fix this problem by introducing new FW feature flag to check power save
support in firmware and then the firmware image can tell to ath10k that power
save mode is not supported in station mode.
Signed-off-by: Venkateswara Naralasetty <vnaralas@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For devices where the FW supports WoWLAN but user-space has not
configured it, we don't do any PCI-specific suspend/resume operations,
because mac80211 doesn't call drv_suspend() when !wowlan. This has
particularly bad effects for some platforms, because we don't stop the
power-save timer, and if this timer goes off after the PCI controller
has suspended the link, Bad Things will happen.
Commit 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
got some of this right, in that it understood there was a problem on
non-WoWLAN firmware. But it forgot the $subject case.
Fix this by moving all the PCI driver suspend/resume logic exclusively
into the driver PM hooks. This shouldn't affect WoWLAN support much
(this just gets executed later on).
I would just as well kill the entirety of ath10k_hif_suspend(), as it's
not even implemented on the USB or SDIO drivers. I expect that we don't
need the callback, except to return "supported" (i.e., 0) or "not
supported" (i.e., -EOPNOTSUPP).
Fixes: 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
Fixes: 77258d409c ("ath10k: enable pci soc powersaving")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Cc: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Don't populate the read-only array reg_hole_list on the stack, instead make
it static. Makes the object code smaller by over 200 bytes:
Before:
text data bss dec hex filename
57518 15248 0 72766 11c3e debug.o
After:
text data bss dec hex filename
57218 15344 0 72562 11b72 debug.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wcn3620 can only operate on 2.4GHz band due to RF limitation.
If wcn36xx digital block is associated with an external IRIS
RF module, retrieve the id and disable 5GHz band in case of
wcn3620 id.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make them const as they are not modified in the file referencing
them. They are only stored in the const field 'hw_ce_reg' of an ath10k
structure. Also, make the declarations in the header const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use ARRAY_SIZE macro, rather than explicitly coding some variant of it
yourself.
Found with: find -type f -name "*.c" -o -name "*.h" | xargs perl -p -i -e
's/\bsizeof\s*\(\s*(\w+)\s*\)\s*\ /\s*sizeof\s*\(\s*\1\s*\[\s*0\s*\]\s*\)
/ARRAY_SIZE(\1)/g' and manual check/verification.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
casting to void pointer from any pointer type and vice-versa is done
implicitly and therefore casting is not needed in such a case.
Done using Coccinellle.
Semantic Patch used :
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T *)x)->f
|
- (T *)
e
)
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP is disabled, we get a compile-time
warning:
drivers/net/wireless/ath/ath10k/pci.c:3417:12: error: 'ath10k_pci_pm_resume' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/pci.c:3401:12: error: 'ath10k_pci_pm_suspend' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_suspend(struct device *dev)
Rather than fixing the #ifdef, this just marks both functions
as __maybe_unused, which is a more robust way to do this.
Fixes: 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.14. Major changes:
wil6210
* support FW RSSI reporting (by mistake this was accidentally
mentioned already in the previous pull request, but now it's really
included)
* make debugfs optional, adds new Kconfig option CONFIG_WIL6210_DEBUGFS
ACPI will rely on device driver to tell it if the device could support
wakeup function when system in D3 state.
This has caused some platform can't support remote wakeup correctly,
because the ACPI wakeup GPE is not enabled, hence registers the .set_wakeup
callback to handle it if device supports wakeup.
Tested with QCA6174 hw3.0, firmware ('WLAN.RM.4.4.1-00008-QCARMSWP-1')
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The actual PCI suspend/resume in ath10k has been handled in wow.c,
but in the case of the device doesn't support remote wakeup,
the .hif_suspend() and .hif_resume() will never be handled.
ath10k_wow_op_suspend()
{
if (WARN_ON(!test_bit(ATH10K_FW_FEATURE_WOWLAN_SUPPORT,
ar->running_fw->fw_file.fw_features))) {
ret = 1;
goto exit;
}
....
ret = ath10k_hif_suspend(ar);
}
So register the PCI PM core to support the suspend/resume if the device
doesn't support remote wakeup.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
User space can remove the P2P management interface while it is active
(for example, while listen/search is active) and this can cause
a crash. Ensure the P2P device is fully stopped before removing.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Connect can take longer than current timeout in some scenarios,
for example with long-range antenna array. Increase the timeout
to support these scenarios.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW starts running it can get D0 to D3 interrupt that is a leftover
from previous system suspend while FW was not running.
As this interrupt is not relevant anymore, clear it part of device reset
procedure.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Re-arrange the code to have dedicated function for device configuration
which takes place before FW starts running.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since debugfs is a kernel configuration option, enable the driver to
compile without debugfs.
Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes there is a firmware crash but the hardware
is not fully stopped and continue to send TX/RX interrupts.
This can cause an overload of messages which can bring the
host down. Add ratelimit to these error messages to fix this.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In commit 9f5bcfe933 ("ath10k: silence firmware file probing
warnings") the firmware loading was changed from request_firmware() to
request_firmware_direct() to silence some warnings in case it fails.
request_firmware_direct() directly searches in the file system only and
does not send a hotplug event to user space in case it could not find
the firmware directly.
In LEDE we use a user space script to extract the calibration data from
the flash memory which gets triggered by the hotplug event. This way the
firmware gets extracted from some vendor specific partition when the
driver requests this firmware. This mechanism does not work any more
after this change.
Fixes: 9f5bcfe933 ("ath10k: silence firmware file probing warnings")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
irq_wq in struct ath10k_sdio is a remnant from an earlier
version of the sdio patchset.
Its use was removed as a result of Kalle's review, but somehow
the struct member survived.
It is not used and can therefore safely be removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In napi_poll, the budget number is used to control the amount of packets
we should handle per poll to balance the resource in the system.
In the list of the amsdu packets reception, we check if there is budget
count left and handle the complete list of the packets, that it will have
chances the very last list will over the budget leftover.
So adding one more parameter - budget_left, this would help while
traversing the list to avoid handling more than the budget given.
Reported-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Fix-suggested-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Link: https://lkml.kernel.org/r/26670dce-4dd2-f8e4-0e14-90d74257e739@virtuozzo.com
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.14. Major changes:
ath10k
* initial UBS bus support (no full support yet)
* add tdls support for 10.4 firmware
ath9k
* add Dell Wireless 1802
wil6210
* support FW RSSI reporting
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Tested-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
vring_idle_trsh is used in the operational driver, hence
should not be defined as a debugfs variable.
Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store initial FW RF calibration result in driver. Set this calibration
result back to FW after each FW reset in order to avoid future calibration
procedures.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While wil_open is executed, any call to netif_running
would return a success. In case there are failures
within wil_open, should not treat the device as if it
is already opened in relevant functions (like FW recovery
and runtime suspend check).
Fix that by checking the device up flag instead.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set wowlan to indicate that 11ad device can wake-up
on any trigger and disconnect.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add statistics for total, min and max suspend time, that
calculates the time the 11ad device was in suspend.
Those statistics will help to estimate the power impact
of d3hot feature.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Reset 11ad device on resume failure only if no_fw_recovery
is not set.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New FW supports reporting RSSI signal in dBm.
Report RSSI to kernel in case FW has this capability.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Validate buffer length has the minimum needed size
when sending management frame to protect against
possible buffer overrun.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath_ps_ops structures are only stored as a reference in the ps_ops
field of a ath_common structure. This field is of type const, so make
the structures as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As the association status changes the driver needs to configure the
hardware. This is done based on information in the "sta" acquired by
ieee80211_find_sta(), which requires the caller to ensure that the "sta"
is valid while its being used; generally by entering an rcu read
section.
But the operations acting on the "sta" has to communicate with the
firmware and may therefor sleep, resulting in the following report:
[ 31.418190] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:238
[ 31.425919] in_atomic(): 0, irqs_disabled(): 0, pid: 34, name:
kworker/u8:1
[ 31.434609] CPU: 0 PID: 34 Comm: kworker/u8:1 Tainted: G W
4.12.0-rc4-next-20170607+ #993
[ 31.441002] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC
(DT)
[ 31.450380] Workqueue: phy0 ieee80211_iface_work
[ 31.457226] Call trace:
[ 31.461830] [<ffffff8008088c58>] dump_backtrace+0x0/0x260
[ 31.464004] [<ffffff8008088f7c>] show_stack+0x14/0x20
[ 31.469557] [<ffffff8008392e70>] dump_stack+0x98/0xb8
[ 31.474592] [<ffffff80080e4330>] ___might_sleep+0xf0/0x118
[ 31.479626] [<ffffff80080e43a8>] __might_sleep+0x50/0x88
[ 31.485010] [<ffffff80088ff9a4>] mutex_lock+0x24/0x60
[ 31.490479] [<ffffff8008595c38>] wcn36xx_smd_set_link_st+0x30/0x130
[ 31.495428] [<ffffff8008591ed8>] wcn36xx_bss_info_changed+0x148/0x448
[ 31.501504] [<ffffff80088ab3c4>]
ieee80211_bss_info_change_notify+0xbc/0x118
[ 31.508102] [<ffffff80088f841c>] ieee80211_assoc_success+0x664/0x7f8
[ 31.515220] [<ffffff80088e13d4>]
ieee80211_rx_mgmt_assoc_resp+0x144/0x2d8
[ 31.521555] [<ffffff80088e1e20>]
ieee80211_sta_rx_queued_mgmt+0x190/0x698
[ 31.528239] [<ffffff80088bc44c>] ieee80211_iface_work+0x234/0x368
[ 31.535011] [<ffffff80080d81ac>] process_one_work+0x1cc/0x340
[ 31.541086] [<ffffff80080d8368>] worker_thread+0x48/0x430
[ 31.546814] [<ffffff80080de448>] kthread+0x108/0x138
[ 31.552195] [<ffffff8008082ec0>] ret_from_fork+0x10/0x50
In order to ensure that the "sta" remains alive (and consistent) for the
duration of bss_info_changed() mutual exclusion has to be ensured with
sta_remove().
This is done by introducing a mutex to cover firmware configuration
changes, which is made to also ensure mutual exclusion between other
operations changing the state or configuration of the firmware. With
this we can drop the rcu read lock.
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The rx ring buffers are added to a hash table if
firmware support full rx reorder. If the full rx
reorder support flag is not set before allocating
the rx ring buffers, none of the buffers are added
to the hash table.
There is a race condition between rx ring refill and
rx buffer replenish from napi poll. The interrupts are
enabled in hif start, before the rx ring is refilled during init.
We replenish buffers from napi poll due to the interrupts which
get enabled after hif start. Hence before the entire rx ring is
refilled during the init, the napi poll replenishes a few buffers
in steps of 100 buffers per attempt. During this rx ring replenish
from napi poll, the rx reorder flag has not been set due to which
the replenished buffers are not added to the hash table
Set the rx full reorder support flag before we allocate
the rx ring buffer to avoid the memory leak.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Each time we get disconnected from AP we get flooded with messages like:
...
ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
<until ratelimit kicks in>
ath10k_warn: 155 callbacks suppressed
...
Use ath10k_dbg() here too.
Signed-off-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the Dell Wireless 1802 card as an AR9462 in the ath9k pci list.
Note that the wowlan feature is supported and has been tested
successfully.
Signed-off by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch fixes a trivial debugfs file permission issue. Debugfs
file ack_to has no write function, so S_IWUSR gets purged.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI interface for all the firmwares(except QCA6174) does not include the
type of peer(default/bss/tdls) requested during peer creation, therefore
target creates a default peer.
TDLS implementation on 10.4 firmware requires host to configure the
peer type(tdls) for TDLS peers. This patch adds peer type parameter to the
existing WMI interface for peer creation to accommodate this requirement.
Tested this change on QCA9888(10.4-3.5.1-00018) and QCA988x(10.2.4.70.9-2)
with ping tests for AP/STA modes.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds the support of TDLS feature for 10.4 firmware
versions.
A new WMI service is added to advertise the support of TDLS for
10.4 firmwares.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Though there is room to accommodate 512 services in wmi service
ready event, target uses only first 4-bits of each 32-bit word for
advertising wmi services thereby limiting max wmi services to 64.
TDLS implementation for 10.4 firmwares introduces new wmi services by
making use of remaining unused bits of each 32-bit word, therefore the
wmi service mapping in host needs to be extended.
This patch adds the logic to extend the wmi SVCMAP to accommodate new
wmi services.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As suggested by Arnd Bergmann, replace
"while (time_before_...) {}"
with
"do {} while (time_before_...)"
This fixes the following warnings detected by gcc 4.1.2:
drivers/net/wireless/ath/ath10k/sdio.c: In function
‘ath10k_sdio_mbox_rxmsg_pending_handler’:
drivers/net/wireless/ath/ath10k/sdio.c:676: warning: ‘ret’ may be used uninitialized in this function
...
drivers/net/wireless/ath/ath10k/sdio.c: In function
‘ath10k_sdio_irq_handler’:
drivers/net/wireless/ath/ath10k/sdio.c:1331: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipsets like QCA9377 have support for USB so add initial USB bus
support to ath10k. With this patch we have the low level HIF and
HTC protocol working and it's possible to boot the firmware,
but it's still not possible to connect or anything like.
More changes are needed for full functionality. For that reason
we print during initialisation:
WARNING: ath10k USB support is incomplete, don't expect anything to work!
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set the a-mpdu reference number in ath10k to make it accessible in the
receivers radiotap header. Implemented as in ath9k. The reference number is
needed for troubleshooting and research at the receivers site (e.g. to identify
mpdu's that were aggregated in an a-mpdu)
Signed-off-by: Matthias Frei <mf@frei.media>
[kvalo@qca.qualcomm.com: fix checkpatch warning, commit log cleanup]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All wmi_services are not printing when we give below command.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services
This patch increases the buffer_len to 8192 to print all the wmi_services.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Copy engine is a host to target communication interface
between wlan firmware and wlan wcn3990 platform driver. Add copy
engine register map for wcn3990 wlan module. This add support
for the copy engine source/destination ring configuration for
wcn3990 chipset.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove bus specific dependencies from CE layer
to have common CE layer across multiple targets.
This is required for adding support for WCN3990
chipset support as WCN3990 chipset uses SNOC
bus interface with Copy Engine endpoint.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 59ae1d127a ("networking: introduce and use skb_put_data()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/wmi.c:3308: code indent should use tabs where possible
Fix that.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Value assigned to variable offset at line 551 is overwritten at line 562,
before it can be used. This makes such variable assignment useless.
Addresses-Coverity-ID: 1226941
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix the following spelling mistakes in messages:
syncronise -> synchronize
unusally -> unusually
addrress -> address
inverval -> interval
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move ath9k_rng_stop/ath9k_rng_start pair into critical section,
use mutex_lock to void potential race accessing.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the worst case, ath9k_rng_stop() may take 10s to stop rng kthread.
The time is too long for users, use wait_event_interruptible_timeout()
instead of msleep_interruptible(), wakup immediately once
kthread_should_stop() is true.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The hard coded register 0x9864 and 0x9924 are invalid
for ar9300 chips.
Cc: <stable@vger.kernel.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One scenario that could lead to UAF is two threads writing
simultaneously to the "tx99" debug file. One of them would
set the "start" value to true and follow to ath9k_tx99_init().
Inside the function it would set the sc->tx99_state to true
after allocating sc->tx99skb. Then, the other thread would
execute write_file_tx99() and call ath9k_tx99_deinit().
sc->tx99_state would be freed. After that, the first thread
would continue inside ath9k_tx99_init() and call
r = ath9k_tx99_send(sc, sc->tx99_skb, &txctl);
that would make use of the freed sc->tx99_skb memory.
Cc: <stable@vger.kernel.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZT/ROAAoJEG4XJFUm622b/IwH+wQtBXP+P57DZ97BdETcZ3Wd
ejm9KKT3IxcP7kzItT9UR1zv7LNx4NgSkJMfhf37jJ1WIuE2fp/ctNv6mz3PvohW
jD1fLynwEMMC7PLHEy5+xGtL61KYc2mtXs/bfLFl94hZUiaocrsBDIT4fXoyIWif
y3MUlBKDbHA27ULRd485C0MRekRSvR/rq6iST4KsIsa8RflJbdH64teTEnQPp4kh
nvhfnaxVEqHK7mYbarC58yYLNOU8gfQXmeeTfd6jhCXRjfEw37IvtNC8BT4B9ZDX
YMZLbkeDSwNGXIH7EIrpGOYHCPh+qsiJ+sx7YodomcJvd1nVrmbuZZt9/EqWXuY=
=Fd/c
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.13. Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
Wireless drivers should not be using ioctl interface,
hence remove this interface for wil6210 driver.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to preserve the connection in suspend/resume flow,
wil6210 host allows going to PCIe D3hot state in suspend,
instead of performing a full wil6210 device reset. This
requires the platform ability to initiate wakeup in case of
RX data. To check that, a new platform API is added.
In addition, add cfg80211 suspend/resume callbacks
implementation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After calling platform_ops.uninit() it is still possible to invoke
platform callbacks.
To prevent this, zero platform_ops right after invoking uninit.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9888 supports VHT80 with 2x2. But it only support 1x1 with VHT160 or
VHT80+80. Inform userspace and the the QCA firmware about that limitation
whenever VHT80+80 or VHT160 is configured.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 hardware can do 4x4 at 80Mhz, but only 2x2 at 160Mhz.
First, report this to user-space by setting the max-tx-speed
and max-rx-speed vht capabilities.
Second, if the peer rx-speed is configured, and if we
are in 160 or 80+80 mode, and the peer rx-speed matches
the max speed for 2x2 or 1x1 at 160Mhz (long guard interval),
then use that info to set the peer_bw_rxnss_override appropriately.
Without this, a 9984 firmware will not use 2x2 ratesets when
transmitting to peer (it will be stuck at 1x1), because
the firmware would not have configured the rxnss_override.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: rebase, cleanup, drop 160Mhz workaround cleanup]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params, rename the title]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath10k firmware doesn't announce its VHT channel width capabilities in
the vht_cap information from the "service ready event" arguments. The
driver must therefore check whether the 160MHz short GI bit is set and
whether the driver still doesn't set the bits for the 160/80+80 MHz
capabilities.
The two bits for the channel width are a two bit integer and not two
separate bits which cannot be parsed without the knowledge of the other
bit. Using IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ (b10..) as a
mask for this task doesn't make any sense. The correct mask for the VHT
channel width should be used instead to make this check more readable.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: separate 160Mhz workaround cleanup, add commit
message]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in ath6kl_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Report per chain RSSI to mac80211.
Signed-off-by: Norik Dzhandzhapanyan <norikd@gmail.com>
[kvalo@qca.qualcomm.com: fix conflicts and style]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define structures for the copy engine ctrl/misc registers,
that includes CE CMD halt, watermark source, watermark destination,
host IE ring, source, destination and dmax ring.
This adds support to avoid the conditional compilation,
code optimization and dynamic configuration of the copy engine
register map for respective hardware bus interface.
Signed-off-by: Sarada Prasanna Garnayak <c_sgarna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The first pull request for 4.13. We have a new driver qtnfmac, but
also rsi driver got a support for new firmware and supporting ath10k
SDIO devices was started.
Major changes:
ath10k
* add initial SDIO support (still work in progress)
rsi
* new loading for the new firmware version
rtlwifi
* final patches for the new btcoex support
rt2x00
* add device ID for Epson WN7512BEP
qtnfmac
* new driver for Quantenna QSR10G chipsets
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZPpCkAAoJEG4XJFUm622bUTMH/ipenw7p7otrhw9qtSBcqBRJ
hS+1i2J+VXDXptFng0ziPWVv6mvhANvBszuOmiNMOgqjx2HrVknwlKUKViklHN3p
E1PE3/A3bRpzBjMk4j8r/Z7VJK3rDa4WSi/AMJtqV9noNm5FfiOrCk7rXm2MLBns
x1Wyr/7OX12hiB4SCoOuOZqS/TvHlNCW71BoyRruq01N2MA1iSonLCYJbovgi7Ds
9acAY90PF8jLC+o7wxYkwuRqWncNhnKOsVNhc/6DKH91zB+C5sw2NGfD3WMfot/Z
9uC5nBWNadoLGi636y+9evIRgNAFCczCZZSUeY7jMWiVn7XyFy8zoc4fv2ZSBto=
=6md1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
The first pull request for 4.13. We have a new driver qtnfmac, but
also rsi driver got a support for new firmware and supporting ath10k
SDIO devices was started.
Major changes:
ath10k
* add initial SDIO support (still work in progress)
rsi
* new loading for the new firmware version
rtlwifi
* final patches for the new btcoex support
rt2x00
* add device ID for Epson WN7512BEP
qtnfmac
* new driver for Quantenna QSR10G chipsets
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
The original idea is to limit the maximum TDLS peer link, but the logic
is always false, and never be able to restrict the number of TDLS peer
creation.
Fix the logic here and also move the checking earlier, so that it could
avoid to handle the failure case, e.g disable the tdls peer, delete the
peer and also vdev count cleanup.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0, QCA9888, QCA9984 supports calibration data in
either OTP or DT/pre-cal file. Current ath10k supports
Calibration data from OTP only.
If caldata is loaded from DT/pre-cal file, fetching board id
and applying calibration parameters like tx power gets failed.
error log:
[ 15.733663] ath10k_pci 0000:01:00.0: failed to fetch board file: -2
[ 15.741474] ath10k_pci 0000:01:00.0: could not probe fw (-2)
This patch adds calibration data support from DT/pre-cal
file. Below parameters are used to get board id and
applying calibration parameters from cal data.
EEPROM[OTP] FLASH[DT/pre-cal file]
Cal param 0x700 0x10000
Board id 0x10 0x8000
Tested on QCA9888 with pre-cal file.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k firmware checks nbytes == 0 as part of determining if DMA
has completed successfully. To help make this work more often,
have the driver initialize nbytes to zero when freeing the descriptor
slot.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This lets one have a clue that maybe timeouts are happening
when we just aren't waiting long enough.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When testing a 9888 chipset NIC, I notice it often takes
almost 2 seconds, and then many times OTP fails, probably due
to the two-second timeout.
[ 2269.841842] ath10k_pci 0000:05:00.0: bmi cmd took: 1984 jiffies (HZ: 1000), rv: 0
[ 2273.608185] ath10k_pci 0000:05:00.0: bmi cmd took: 1986 jiffies (HZ: 1000), rv: 0
[ 2277.294732] ath10k_pci 0000:05:00.0: bmi cmd took: 1989 jiffies (HZ: 1000), rv: 0
So, increase the BMI timeout to 3 seconds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reverts commit b057886524 ("ath10k: do not use coherent memory for
allocated device memory chunks") in 2015 which converted this allocation from
dma_map_coherent() to kzalloc() / dma_map_single().
The current problem manifests when using later model NICs with larger
(>700KiB) scratch spaces in memory. Although the kzalloc call
succeeds, the software IOMMU TLB code (via dma_map_single()) panics
because it can't find 700KiB of linear physmem bounce buffers for DMA.
Now, this is a bit of a silly failure mode for the dma map API,
but it's what we currently have to play with.
In these cases, doing kzalloc() works fine, but the dma_map_single()
call fails.
After chatting with Linus briefly about this, it indeed should be
using dma_alloc_coherent() for doing larger device memory allocation
that requires some kind of physical address mapping.
You're not supposed to be using kzalloc and dma_map_* calls for
large memory regions, and I'm guessing not for long-held mappings
either. Typically dma mappings should be temporary for DMA,
not long held like these.
Now, since hopefully the major annoying underlying problem has also been
addressed (ie, ath10k is no longer tears down all of these allocations
and reallocates them every time the vdevs are brought down) fragmentation
should stop being such a touchy issue. If it is though, using
dma_alloc_coherent() use gets us access to the CMB APIs too relatively
easily and ideally we would be allocating memory early in boot for
exactly these reasons.
Signed-off-by: Adrian Chadd <adrian@FreeBSD.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wil6210 devices can have different PCIe bar size, hence get the
bar size from PCIe device instead of using a constant bar size.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set resetting flag early when stopping AP to avoid
disconnect events as a result of disconnect command
sent during AP stop procedure.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Module parameter allows to load specific FW used
for FTM testing.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added vendor commands for low level control over
RF sectors. It allows user space a fine-grained control
over RF characteristics for TX and RX, such as direction
and gain of TX/RX. Main usages are debugging and diagnostics,
but also operational use cases.
API includes getting/setting a specific RF sector
configuration, as well as getting/setting the selected
sector which is used to communicate with a station.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA4019 firmware 10.4-3.2.1-00050 reports only HT MCS rates between
0-9. But 802.11n MCS rates can be larger than that. For example a 2x2
device can send with up to MCS 15.
The firmware encodes the higher MCS rates using the NSS field. The actual
calculation is not documented by QCA but it seems like the NSS field can be
mapped for HT rates to following MCS offsets:
* NSS 1: 0
* NSS 2: 8
* NSS 3: 16
* NSS 4: 24
This offset therefore has to be added for HT rates before they are stored
in the rate_info struct.
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The array fields in struct wmi_start_scan_arg that are checked here are
fixed size arrays so they can never be NULL.
Addresses-Coverity-ID: 1260031
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The SMD channel is not the primary WCNSS channel and must explicitly be
closed as the device is removed, or the channel will already by open on
a subsequent probe call in e.g. the case of reloading the kernel module.
This issue was introduced because I simplified the underlying SMD
implementation while the SMD adaptions of the driver sat on the mailing
list, but missed to update these patches. The patch does however only
apply back to the transition to rpmsg, hence the limited Fixes.
Fixes: 5052de8def ("soc: qcom: smd: Transition client drivers from smd to rpmsg")
Reported-by: Eyal Ilsar <c_eilsar@qti.qualcomm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When driver fail to reset card ah->curchan value stay NULL. When
later driver try to update tx power it oops by using ah->curchan
(calltrace is shown below).
This problem were reported at various places and for some it was
fixed by making ath9k_hw_chip_reset() do not fail. I have this bug
report on some oldish RHEL kernel with AR9285, however it's hard to
debug where reset fail when kernel OOPS, so I think this patch
should be applied. Hopefully ah->curchan is not used unconditionally
on other places until is initialized on ath9k_config().
ath: phy0: Chip reset failed
ath: phy0: Unable to reset hardware; reset status -22 (freq 2412 MHz)
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<f8a35585>] ath9k_hw_set_txpowerlimit+0x25/0x80 [ath9k_hw]
Oops: 0000 [#1] SMP
<snip>
Call Trace:
[<f8aac1aa>] ? ath9k_cmn_update_txpow+0x1a/0x30 [ath9k_common]
[<f8cf4f4e>] ? ath_complete_reset+0x4e/0x130 [ath9k]
[<f8cf54d7>] ? ath9k_start+0x127/0x1e0 [ath9k]
[<f8c2e52f>] ? ieee80211_do_open+0x30f/0x910 [mac80211]
[<c07bd96d>] ? dev_open+0x8d/0xf0
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The array field eeprom_data in struct th9k_platform_data
is a fixed size array so it can never be NULL.
Addresses-Coverity-ID: 1364903
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use memdup_user() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The AR5K_EEPROM_READ macro returns with -EIO if a read error
occurs causing a memory leak on the allocated buffer buf. Fix
this by explicitly calling ath5k_hw_nvram_read and exiting on
the via the freebuf label that performs the necessary free'ing
of buf when a read error occurs.
Detected by CoverityScan, CID#1248782 ("Resource Leak")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
An issue was found brcmfmac driver in which a skbuff in .start_xmit()
callback was actually cloned. So instead of checking for sufficient
headroom it should also be writable. Hence use skb_cow_head() to
check and expand the headroom appropriately.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Somehow I missed this in my RX rate cleanup series, causing some
drivers to not report correct bandwidth since this flag isn't
used by mac80211 anymore. Fix this, and make hwsim also report
higher bandwidths appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
QCA9xxx and QCA61x4/QCA93xx are using different wmi operation, in order
for userspace to differentiate it, appends the wmi_op_version information
alone with the get_version command.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During write to debugfs file simulate_fw_crash, fixed-size local buffer
'buf' is accessed and modified at index 'count-1', where 'count' is the
size of the write (so potentially out of bounds).
This patch fixes this problem.
Signed-off-by: Michael Mera <dev@michaelmera.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipsets like QCA6584 have support for SDIO so add initial SDIO bus support to
ath10k. With this patch we have the low level HTC protocol working and it's
possible to boot the firmware, but it's still not possible to connect or
anything like. More changes are needed for full functionality. For that reason
we print during initialisation:
WARNING: ath10k SDIO support is incomplete, don't expect anything to work!
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[kvalo@qca.qualcomm.com: refactoring, cleanup, commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since both SDIO based chipsets will use different
firmware from the PCIe and AHB chipsets, the fw file name
must be different depending on bus type.
The new firmware names are:
For PCIe and AHB:
firmware-<api_version>.bin (same as before)
For SDIO:
firmware-sdio-<api_version>.bin
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added support for extended ready message.
The extended ready message contains the maximum bundle
count supported by SDIO chipsets.
It is transmitted by SDIO chipset only and replaces the
"standard" ready message in this case.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Special BMI get target info function for SDIO.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Extra initializations needed by all sdio boards.
Derived from qcacld.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Debug masks for SDIO HIF layer.
Address definitions for SDIO/mbox based chipsets.
Augmented struct host_interest with more members.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Code refactorization:
Moved the code for ep 0 in ath10k_htc_rx_completion_handler
to ath10k_htc_control_rx_complete.
This eases the implementation of SDIO/mbox significantly since
the ep_rx_complete cb is invoked directly from the SDIO/mbox
hif layer.
Since the ath10k_htc_control_rx_complete already is present
(only containing a warning message) there is no reason for not
using it (instead of having a special case for ep 0 in
ath10k_htc_rx_completion_handler).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch moves the HTC ctrl service connect from
htc_wait_target to htc_init.
This is done in order to make sure the htc ctrl service
is setup properly before hif_start is called.
The reason for this is that we want the HTC ctrl service
callback to be initialized before the target sends the
HTC ready message.
The ready message will always be transmitted on endpoint 0
(which is always assigned to the HTC control service) so it
makes more sense if HTC control has been connected before the
ready message is received.
Since the service to pipe mapping is done as a part of
the service connect, the get_default_pipe call is redundant
and was removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The RX trailer parsing is now capable of parsing lookahead reports.
A lookahead contains the first 4 bytes of the next HTC message
(that will be read in the next SDIO read operation).
Lookaheads are used by the SDIO/mbox HIF layer to determine if
the next message is part of a bundle, which endpoint it belongs
to and how long it is.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Changed ath10k_htc_notify_tx_completion and
ath10k_htc_process_trailer from static to non static.
These functions are needed by SDIO/mbox.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_roamed() and cfg80211_roamed_bss() take the same arguments
except that cfg80211_roamed() requires the BSSID and
cfg80211_roamed_bss() requires the bss entry.
Unify the two functions by using a struct for driver initiated
roaming information so that either the BSSID or the bss entry can be
passed as an argument to the unified function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[modified the ath6k, brcm80211, rndis and wlan-ng drivers accordingly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[modify brcmfmac to remove the useless cast, spotted by Arend]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This field will need to be used again for HE, so rename it now.
Again, mostly done with this spatch:
@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+cipAAoJEG4XJFUm622b+04H/2u7zhIqv3R5NsmGRlwjKmvd
6us1hcYzUiBW1kBFFtcvokwgqv3Rw/EUi+NYA5UCHgo30HTVJWTqW0q+BUEI7U0X
iwuFdHbs/qjj8hXKgZwaJMVyRhXAbq+iHYaMY5OEDNTRSbxqXA4V69SHGK9vLX0l
KQLJBZX3etnwsyRWrmd4E0roGGfD5tMPpGMUDSlvTPWt0I+1QFUxRI9ohn1fRBpD
p+UHHC+SYF6NzxvfqyPwm6ndb2XOwdAKYljlf4KrBwHtSXvAH8p5EASm4PjGbavY
0mrkv0cb8QOKQNVe9q4B4AmM4iAITZ9i3sQBPJ+EBN2P+kS/lFU5L/+5z3VQjms=
=KTEG
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
-----BEGIN PGP SIGNATURE-----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=f4VT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.12. Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
As per latest regulatory update for India, channel 52, 56, 60, 64
is no longer restricted to DFS. Enabling DFS/no infra flags in driver
results in applying all DFS related restrictions (like doing CAC etc
before this channel moves to 'available state') for these channels
even though the country code is programmed as 'India' in he hardware,
fix this by relaxing the frequency range while applying RADAR flags
only if the country code is programmed to India. If the frequency range
needs to modified based on different country code, ath_is_radar_freq
can be extended/modified dynamically.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce a debugfs option to manually override the noise floor,
ignoring the automatically tuned noise floor of the driver/hw.
In my tests with a AR9580 based module and a tx99 5 MHz interferer,
I could tune the noisefloor to -95 dBm or above to allow communication
again. The automatic noise floor calibration sometimes could adapt to
the situation as well, but not reliably and permanently.
I would consider this "feature" experimental and interesting for people
debugging the noise floor calibration or other effects of the hardware.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For QCA6174 hw3.0, since WLAN.RM.4.4-00022-QCARMSWPZ-2, it starts to
support the board ID information from otp, with some devices released on
the market that didn't calibrated with OTP, will have 0 for board ID
information, which cause the backward compatibility issue and was fixed
in commit 'd2e202c06ca4 ("ath10k: ignore configuring the incorrect board_id")'
So bump the fw api version to differentiate the latest firmware support.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
spectral_bin length (number of bins per fft sample) is usually
a value where (2^n = value), n is an integer. All of the QCA99X0
family of chipsets seems to report a spectral_bin length of
2^n + 'm' bytes, where m = 4, 12 based on the chipset. This 'm'
bytes seems to carry some radar related info which is currently
discarded only for 'bin_len = 68' bytes. Extend this discarding of
irrelevant 'bin_len' for QCA9984, QCA9888, IPQ4019 as well by
introducing a hardware parameter 'spectral_bin_discard'. Also
for QCA988X based family of chipsets which doesn't seem to have this
issue and also for some of the hardware which I have not tested
like QCA6174/QCA9377 the existing behaviour is retained as it is.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The macro results are assigned to u8 variables/fields. Adding the cast
fixes plenty of clang warnings about "implicit conversion from 'int' to
'u8'".
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the Dell Wireless 1601 card as an AR9462 in the ath9k pci list.
Note that the wowlan feature is supported and has been tested
successfully.
Signed-off-by: Damien Thébault <damien@dtbo.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The > should be >= or we read one space beyond the end of the array.
Fixes: ab5c4f71d8 ("ath9k: allow to load EEPROM content via firmware API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case wil6210 resume fails, wil6210 suspend function will try
to access the suspended device in the next kernel suspend.
To prevent that, add wil_status_suspended flag to indicate if the
device is already suspended and clear it only if the resume succeeds.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Array index 'i' is used before limits check.
Fix this by doing limits check first.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
debugfs ioblob function is called by the FW logs scripts
to copy the FW logs via PCIe.
As the FW logs collection is done in parallel to the operational
11AD actions, the HALP voting can take place during 11AD reset flow
and other sensitive scenarios.
To prevent that, remove HALP voting from the ioblob function.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case count is not multiple of 4, there is a read access in
wil_memcpy_toio_32() from outside src buffer boundary.
In wil_memcpy_fromio_32(), in case count is not multiple of 4, there is
a write access to outside dst io memory boundary.
Fix these issues with proper handling of the last 1 to 4 copied bytes.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver fails to load FW for sparrow D0 devices in some cases.
Fix this by returning correct value from wil_fw_verify_file_exists
when D0 FW file is not detected for any reason.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During the suspend flow, wil6210 HW can send sporadic interrupts,
while PCIe bus is not operational.
To prevent that, keep the interrupts disabled during the suspend
flow and re-enable them only after PCIe enablement in resume.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing code that ignores connection events during
reset flow will never take effect since it locks the
same mutex taken by the reset flow.
In addition, in case of unsolicited disconnect events ignore
those as well since device is about to get reset.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 11ad spec requires 11ad devices to be able to receive 8KB
packets over the air. Currently this is only possible by
loading the driver with mtu_max=7912 but this also forces
a smaller block ACK window size which reduces performance
for stations which transmit normal sized packets (<2KB).
Fix this problem as follows:
1. Add a module parameter rx_large_buf that when set,
will allocate 8KB RX buffers regardless of mtu_max
setting.
2. When receiving block ACK request agree to any window
size not above our maximum, regardless of the mtu_max setting.
This means if the other side transmits small packets (2KB)
it can still set up block ACK with a large window size,
and get better performance.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The power save profile is set to default state in case of FW reset,
regardless of the state before the reset took place.
Fix this by saving the current power save profile and restore it
in case of FW reset.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Communication with FW must be done before wil->status
is initialized in order to properly handle cases where
communication with FW halts during reset sequence.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In 'ath10k_ce_alloc_pipe' the compile time sanity check to
ensure that there is sufficient buffers in CE4 for HTT Tx
MSDU descriptors, but this did not take into account of the
case with 'peer flow control' enabled, fix this.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix fallout too.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.
While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lots of bugfixes as usual but also some new features.
Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
rt2x00
* add support MT7620
mwifiex
* enable auto deep sleep mode for USB chipsets
brcmfmac
* add support for network namespaces (WIPHY_FLAG_NETNS_OK)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY55+nAAoJEG4XJFUm622bRUAIAJfCM5YFyh9Y/XV147JshdGi
xScDAgwIA1/o+iHfvTsjSH3/uoH3JhsiqfcXN7R80kyvG7HrUeXaebmUDgbBvOOj
FTMuytiD+xkgEKVjWIwtXUYqctyzQ8ofxIQJ2W5E9CbEYAZ43uEcXzdnhBKVaVuY
XPw59MF5vRGDDXTnTf4af4OC+L1QqwUqsyi4j7oMIfexieMGQxQL0JYOyHweCnCV
gMz/kTxAIcmC1yOiunu8VyU4kK8borW36wC7XEE3MOXhqSKnQjyhI/efA76AKX0j
O7sfEKCFlZU1xXQbkB9ecbKc2jyMefiE0gwLWWI5dwKhnUS2qQ6GS8ML+NMfV0g=
=B2X+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-04-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Lots of bugfixes as usual but also some new features.
Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
rt2x00
* add support MT7620
mwifiex
* enable auto deep sleep mode for USB chipsets
brcmfmac
* add support for network namespaces (WIPHY_FLAG_NETNS_OK)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate line
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix output from checkpatch.pl like:
Symbolic permissions 'S_IRUSR' are not preferred.
Consider using octal permissions '0400'.
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate lin
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch helps to fix TPC stats to display the stats
properly. Here cosmetic change has been done to print the
TPC stats for all the cases 1.CDD 2.STBC 3.TXBF
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove obselete Copy Engine comments referring to the function
ath10k_ce_sendlist_send as this function was removed long time back
by the commit 2e761b5a52 ("ath10k: remove ce_sendlist_send").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add an ath10k HTC debug message when insufficient tx credits
are available to send the WMI commands. This is very useful
in debugging issues like 'tx credit starvation' that could
possibly happen with multiclient setup with constant roaming
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It seems set_coverage_class_work is not cancelled anywhere,
though I could not find a crash/warning with this existing
design, its safer to cancel it during stop() and also before
restarting the hardware.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If station advertises diffferent NSS capabilities in Rx_mcs set
of HT and VHT IEs in assoc req, the current NSS computation
logic configures the NSS support only based on Rx_mcs set of
HT capabilities in the driver. This is configuring the station
NSS capabilities incorreclty in the target.
For example, if station advertise Rx_mcs set as 2 spatial streams
in HT capabilities and 1 spatial streams in VHT capabilities in
assoc request, as per current logic we are calculating nss from
HT capabilities and the driver sets peer_num_spatial_streams as
2 for the station which is configured in VHT 1*1.
This patchs fix this issue by calculating the nss from VHT cap if
station supports vht.
Signed-off-by: Venkateswara Rao Naralasetty <c_vnaral@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 36bcce4306 ("ath9k_htc: Handle storage devices")
Cc: stable <stable@vger.kernel.org> # 2.6.39+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move NAPI enable to 'ath10k_ahb_hif_start' from
'ath10k_ahb_hif_power_up'. This is to maintain the symmetry
of calling napi_enable() from ath10k_ahb_hif_start() so that it
matches with napi_disable() being called from ath10k_pci_hif_stop().
This change is based on the crash fix from Kalle for PCI interface in
commit 1427228d58 ("ath10k: fix napi crash during rmmod when probe
firmware fails").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By moving these client drivers to use RPMSG instead of the direct SMD
API we can reuse them ontop of the newly added GLINK wire-protocol
support found in the 820 and 835 Qualcomm platforms.
As the new (RPMSG-based) and old SMD implementations are mutually
exclusive we have to change all client drivers in one commit, to make
sure we have a working system before and after this transition.
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Channels 34/38/42/46 can only be used for compatibility with old devices sold
in Japan. Modern products, such as AR6003/AR6004 don't support these channels.
Keeping them in the upstream is error prone and requires full network stack
support. A custom patch should be used in case such compatibility is required.
Without this one, a user is able to start an AP using wpa_supplicant,
for example, on one of these channels (34/38/42/46), without getting
any warning/error from the cfg80211 or ath6kl - which is correct
(since these channels match regdom rules). However, the AR6003 and its
firmware (we're using v3.4.0.225) will fail and return
"WMI_CMDERROR_EVENTID" with "INVALID_PARAM" error code.
Signed-off-by: Rostyslav Khudolii <rkhudolii@airtame.com>
Cc: Attila Sukosd <attila@airtame.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check of len > buf_len is redundant as len is initialized
to 0 and buf_len to 4096, so this comparison is always false.
Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix typo (spelling mistake) in wmi.h
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I failed to notice that commit 523f6701db ("ath10k: update available channel
list for 5G radio") added two new warnings:
drivers/net/wireless/ath/ath10k/mac.c:3129:6: warning: symbol 'ath10k_mac_update_channel_list' was not declared. Should it be static?
drivers/net/wireless/ath/ath10k/mac.c:3170: Alignment should match open parenthesis
Fix those.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the 'commit ebee76f7fa ("ath10k: allow setting coverage class")',
it inherits the design and the address offset from ath9k, but the address
is not applicable to QCA6174, which leads to a random crash while doing the
resume() operation, since the set_coverage_class.ops will be called from
ieee80211_reconfig() when resume() (if the wow is not configured).
Fix the incorrect address offset here to avoid the random crash.
Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2.
kvalo: this also seems to fix a regression with firmware restart.
Fixes: ebee76f7fa ("ath10k: allow setting coverage class")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fetch target operating channel during potential radar detection when
the interface is just brought up, but no channel is assigned from
userspace. In this scenario rx_channel may not be having a valid pointer
hence fetch the target operating channel to avoid warnings as below
which can be triggered by the commands with DFS testing over longer run
comamnds:
iw wlan1 set type mesh
ifconfig wlan1 up (valid tgt_oper_chan only)
iw wlan1 cac trigger freq 5260 HT20 (valid rx_channel, tgt_oper_chan)
iw wlan1 cac trigger freq 5280 HT20
iw wlan1 cac trigger freq 5300 HT20
Once the CAC expires, current channel context will be removed and
we are only left with the fallback option of using 'target operating
channel'
Firmware and driver log:
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath: phy1: DFS: radar found on freq=5260: id=5, pri=3151, count=6,
count_false=11
ath: phy1: DFS: radar found on freq=5280: id=1, pri=1351, count=6,
count_false=4
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
Call trace:
WARNING: CPU: 1 PID: 2145 at
backports-20161201-3.14.77-9ab3068/net/wireless/chan.c:265
cfg80211_set_dfs_state+0x3c/0x88 [cfg80211]()
Workqueue: phy1 ieee80211_dfs_radar_detected_work
[mac80211]
[<c0320770>] (warn_slowpath_null) from [<bf79b90c>]
(cfg80211_set_dfs_state+0x3c/0x88 [cfg80211])
[<bf79b90c>] (cfg80211_set_dfs_state [cfg80211]) from
[<bf79697c>] (cfg80211_radar_event+0xc4/0x140 [cfg80211])
[<bf79697c>] (cfg80211_radar_event [cfg80211]) from
[<bf83c058>] (ieee80211_dfs_radar_detected_work+0xa8/0xb4 [mac80211])
[<bf83c058>] (ieee80211_dfs_radar_detected_work
[mac80211]) from [<c0339518>] (process_one_work+0x298/0x4a4)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check on ret for an error is redundant because it is already been
checked for non-zero earlier on and ret is never non-zero at this point.
Fix this by removing the redundant check and error message.
Detected by CoverityScan, CID#1357170 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Doing so enables the FFT generation without prior
configuration, leading to an IRQ storm caused by
invalid (or at least unwanted) PHY errors.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If a 5 GHz radio is calibrated for operation in both
the low band (channels 36 to 64) and high band(channels 100 to 169),
hardware allows operations in all the listed channels. However,
if the chip has been calibrated only for the low/high band and
a high/low band channel is configured, due to lack of calibration
there will be potentially invalid signal on those non calibrated channels.
To avoid this problem this patch sets IEEE80211_CHAN_DISABLED flag for
those non calibrated channels by using low_5ghz_chan and high_5ghz_chan
values which we get from target through wmi service ready event.
Driver initialized flags are getting re initialized in handle_channel
in cfg80211. So calling the function to disable the non supported channel
from reg_notifier().
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DFS is not enabled in hostapd (ieee80211h=0) DFS channels shall
not be available for use even though the hardware may have the capability
to support DFS. With this configuration (DFS disabled in hostapd) trying to
bring up ath10k device in DFS channel for AP mode fails and trying to
simulate DFS in ath10k debugfs results in a warning in cfg80211 complaining
invalid channel and this should be avoided in the driver itself rather than
false propogating RADAR detection to mac80211/cfg80211. Fix this by
checking for the first vif 'is_started' state(should work for client mode
as well) as all the vifs shall be configured for the same channel
sys/kernel/debug/ieee80211/phy1/ath10k# echo 1 > dfs_simulate_radar
WARNING: at net/wireless/chan.c:265 cfg80211_radar_event+0x24/0x60
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
WARNING: at net/wireless/nl80211.c:2488 nl80211_get_mpath+0x13c/0x4cc
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a new value to the oob_mode module parameter for
supporting AP certification.
All enabled values of oob_mode (>0) are intended only
for debugging and diagnostics.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver always invoke cfg80211_disconnected() with locally_generated as
false.
Fix this by reporting true whenever the disconnect is triggered from
upper layers (cfg80211) or from within the driver itself (reset,
deinit).
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon connect timeout driver invokes _wil6210_disconnect() which iterates
over sta array and disconnects each connected sta. In practice, because
the connection is still ongoing and because cid is not yet allocated,
disconnect is not actually happening. This leaves FW in connecting
state while driver is in disconnected state.
To fix this, upon connect timeout, explicitly send WMI_DISCONNECT_CMDID
to FW to make sure it gets disconnected.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When flush is done, pending events list is manipulated
without taking the proper spinlock, which could lead to
memory corruption if list is manipulated by wmi worker
or by interrupt routine.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In a fast disconnect/connect sequence, cfg80211_connect_result() can
fail to find the bss object which the driver is connecting to. Detailed
sequence of events:
* Driver is connected in STA mode
* Disconnect request arrives from user space. Driver disconnects and
calls cfg80211_disconnected() which adds new event to the
cfg80211_wq worker thread
* Connect request arrives from user space. cfg80211_connect() stores
ssid/ssid_len and calls rdev_connect()
* __cfg80211_disconnected() runs in worker thread and zero
wdev->ssid_len
* Connect succeeds. Driver calls cfg80211_connect_result() which fails
to find the bss because wdev->ssid_len is zero
To overcome this, upon connect request, store the bss object in the
driver and upon connect completion pass it to kernel using
cfg80211_connect_bss().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After setting HALP ICR bit, we keep it set until HALP unvote.
Masking HALP ICR should protect the driver from hitting the HALP ICR
over and over again. However, in case there is another MISC ICR
we will read the HALP ICR and issue a completion. This can lead to
a case where HALP voting is completed immediately, as the completion
is already set.
Reinit the HALP completion before the actual vote will clear previous
completions and protect from such cases.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some dynamic debug printouts in driver are using print_hex_dump_bytes.
However, with dynamic debug disabled, print_hex_dump_bytes outputs to
log unconditionally.
Use print_hex_dump_debug instead to prevent log pollution when dynamic
debug disabled.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver uses the bus_request platform operation to
request resources from the platform for a specific bandwidth.
Currently the driver requests resources for the maximum
theoretical bandwidth, when interface is brought up.
Refine this process a bit: now the driver will request a
small amount of resources when interface is up, and will only
issue the maximum request when connected.
This mechanism will be improved further in the future to make
more refined requests based on actual bandwidth.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver should not allow starting any type of scan on a stopped
P2P device. Current implementation only checked social scan.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
device supports 48bit addresses, reflect that by
setting the dma mask accordingly.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Reorder 'out_free_dxe_pool' and 'out_free_dxe_ctl' error handling labels
in order to match the way resources have been allocated.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Doing a channel switch via hostapd_cli seems to update
the new channel context for each VAP's appropriately as below
in 'ath10k_mac_update_vif_chan', hence we can safely suppress the
warning that shows up during this operation and dump the warning only
if no vaps are available for channel switch
hostapd_cli -i wlan0 chan_switch 5 5200
OK
ath10k_pci : mac chanctx switch n_vifs 3 mode 1
ath10k_pci : mac chanctx switch vdev_id 2 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 1 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 0 freq 5180->5200 width 0->0
Call Trace:
WARNING: backports-20161201-3.14.77-9ab3068/drivers/net/wireless/ath/ath10k/mac.c:7126
[<c022f2d4>] (warn_slowpath_null) from [<bf7f150c>]
(ath10k_reconfig_complete+0xe4/0x25c [ath10k_core])
[<bf7f150c>] (ath10k_reconfig_complete [ath10k_core])
[<bf7f35f0>] (ath10k_mac_vif_ap_csa_work+0x214/0x370 [ath10k_core])
[<bf7f38b8>] (ath10k_mac_op_change_chanctx+0x108/0x128 [ath10k_core])
[<bf782ac0>] (ieee80211_recalc_chanctx_min_def+0x30c/0x430 [mac80211])
[<bf7830a4>] (ieee80211_recalc_smps_chanctx+0x2ec/0x840 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context+0x7c/0xf8 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context [mac80211])
[<bf76e5d4>] (ieee80211_csa_finalize_work+0x5c/0x88 [mac80211])
Fixes: d7bf4b4aba ("ath10k: fix ar->rx_channel updating logic")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9377 is the family of QCA61x4 which shared the same procedure
to enable the hardware clock that could improve the firmware download time.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Len Brown reported the system resume time is taking more than 2 seconds in
bug - https://bugzilla.kernel.org/show_bug.cgi?id=185621.
The reason of the 2 seconds is due to the firmware download time.
The chip is booted up in the default reference clock speed to handle the
firmware download to chip memory and advanced to the support higher speed
clock to run the firmware after all. The default reference clock in the
hardware is slow so that the firmware download time is taking up to 2
seconds for a 600KB firmware file.
[76796.349701] ath10k_pci : boot uploading firmware image len 688691
[76798.334612] ath10k_pci : htt tx max num pending tx 1056
The resolution here is to enable the higher speed clock if the hardware
supported before the firmware download at BMI stage, so that the hardware
can handle the firmare download in a more efficient way. This can help to
improve the firmware download time from 2 seconds to around 500ms for the
same 600KB firmware file.
[322858.577919] ath10k_pci boot uploading firmware image len 688691
[322859.093094] ath10k_pci htt tx max num pending tx 1056
The steps to advance to the higher speed clock is very hardware specific,
so adding the hardware ops for the hardware that can support this.
Reported-by: Len Brown <lenb@kernel.org>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This function contains the HT calculations, which makes no
sense - split that out into a separate function. As a side
effect, this makes the 60G flag independent from HT_MCS so
remove the MCS one from wil6210 (also deleting a duplicate
assignment.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature
wholesale in all mac80211-based drivers that do not set the
IEEE80211_VIF_BEACON_FILTER flags on their interfaces. mac80211 will
be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and
will detect when the thresholds set by
ieee80211_set_cqm_rssi_range_config are crossed. Remaining (few)
drivers need code to enable the firmware to monitor the thresholds.
This is mostly only compile-tested.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
into the tree before adding new users through -next trees.
-----BEGIN PGP SIGNATURE-----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=Bge/
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-03-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
This contains just the average.h change in order to get it
into the tree before adding new users through -next trees.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified, among others, by device and sybsystem ids.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
To solve the issue QCA uses SMBIOS type 0xF8 to store Board Data File Name
Extension to specify the extension/variant name. The driver will take the
extension suffix into consideration and will load the right (non-default)
board data file if necessary.
If it is unnecessary to use extension board data file, please leave the
SMBIOS field blank and default configuration will be used.
Example:
If a default board data file for a specific board is identified by a string
"bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,
subsystem-device=0310"
then the OEM specific data file, if used, could be identified by variant
suffix:
"bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,
subsystem-device=0310,variant=DE_1AB"
If board data file name extension is set but board-2.bin does not contain
board data file for the variant, the driver will fallback to the default
board data file not to break backward compatibility.
This was first applied in commit f2593cb1b2 ("ath10k: Search SMBIOS for OEM
board file extension") but later reverted in commit 005c3490e9 ("Revert
"ath10k: Search SMBIOS for OEM board file extension"". This patch is now
otherwise the same as commit f2593cb1b2 except the regression fixed.
Signed-off-by: Waldemar Rymarkiewicz <ext.waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Declaring the factor is counter-intuitive, and people are prone
to using small(-ish) values even when that makes no sense.
Change the DECLARE_EWMA() macro to take the fractional precision,
in bits, rather than a factor, and update all users.
While at it, add some more documentation.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix typos and add the following to the scripts/spelling.txt:
aligment||alignment
I did not touch the "N_BYTE_ALIGMENT" macro in
drivers/net/wireless/realtek/rtlwifi/wifi.h to avoid unpredictable
impact.
I fixed "_aligment_handler" in arch/openrisc/kernel/entry.S because
it is surrounded by #if 0 ... #endif. It is surely safe and I
confirmed "_alignment_handler" is correct.
I also fixed the "controler" I found in the same hunk in
arch/openrisc/kernel/head.S.
Link: http://lkml.kernel.org/r/1481573103-11329-8-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit f2593cb1b2.
Paul reported that this patch with older board-2.bin ath10k initialisation
fails on Dell XPS 13:
ath10k_pci 0000:3a:00.0: failed to fetch board data for bus=pci,vendor=168c,
device=003e,subsystem-vendor=1a56,subsystem-device=1535,variant=RV_0520 from
ath10k/QCA6174/hw3.0/board-2.bin
The reason is that the older board-2.bin does not have the variant version of
the image name and ath10k does not fallback to the older naming scheme.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=185621#c9
Fixes: f2593cb1b2 ("ath10k: Search SMBIOS for OEM board file extension")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the OTP register definitions for the AR934x and AR9550
WMAC SoC.
Previously, the ath9k driver was unable to initialize the integrated
WMAC on an Aerohive AP121:
| ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004
| ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004
| ath: phy0: Unable to initialize hardware; initialization status: -5
| ath9k ar934x_wmac: failed to initialize device
| ath9k: probe of ar934x_wmac failed with error -5
It turns out that the AR9300_OTP_STATUS and AR9300_OTP_DATA
definitions contain a typo.
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Fixes: add295a4af "ath9k: use correct OTP register offsets for AR9550"
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath_tx_count_airtime is doing a lot of unnecessary work:
- Redundant station lookup
- Redundant rcu_read_lock/unlock
- Useless memcpy of bf->rates
- Useless NULL check of bf->bf_mpdu
- Redundant lookup of the skb tid
Additionally, it tries to look up the mac80211 queue index from the txq,
which fails if the frame was delivered via the power save queue.
This patch fixes all of these issues by passing down the right set of
pointers instead of doing extra work
Cc: stable@vger.kernel.org
Fixes: 63fefa0504 ("ath9k: Introduce airtime fairness scheduling between stations")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using a private copy of struct net_device_stats in struct
ath6kl_vif, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The variant[] string will be valid only if the bdf_ext is set.
The string memory needs to be null-terminated to avoid the undefined garbage
appended by the subsequent board file name creation.
ath10k_pci 0000:04:00.0: failed to fetch board data for
"bus=pci,vendor=168c,device=003e,subsystem-vendor=168c,subsystem-device=3363��P�����"
from ath10k/QCA6174/hw3.0/board-2.bin
Fixes: f2593cb1b2 ("ath10k: Search SMBIOS for OEM board file extension")
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath10k unncessarily warns about board id not available from OTP:
ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
ath10k_pci 0000:02:00.0: firmware ver 10.2.4.70.9-2 api 5 features no-p2p,raw-mode crc32 b8d50af5
ath10k_pci 0000:02:00.0: board id is not exist in otp, ignore it
ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
But not all boards have the board id in OTP so this is not a problem and no
need to confuse the user with that info. So this can be safely changed to a
debug message.
Also fix grammar in the debug message.
Fixes: d2e202c06c ("ath10k: ignore configuring the incorrect board_id")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware files are versioned to prevent older
driver instances to load unsupported firmware
blobs. This is reflected with a fallback logic
which attempts to load several firmware files.
This however produced a lot of unnecessary
warnings sometimes confusing users and leading
them to rename firmware files making things even
more confusing.
Hence use request_firmware_direct() which does not
produce extra warnings. This shouldn't really
break anything because most modern systems don't
rely on udev/hotplug helpers to load firmware
files anymore. For example it was confirmed that
LEDE does not user helper.
This also fixes a 60 second delay per _each_
unexistent firmware/calibration file with distros
which have CONFIG_FW_LOADER_USER_HELPER_FALLBACK
enabled, RHEL being a notable example. Using
ath10k with firmware-2.bin this might end up
into a five minute delay in boot.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[kvalo@qca.qualcomm.com: add more info to the commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This way user has a better idea what file exactly is missing.
This is needed when we switch to using request_firmware_direct() which doesn't
print any errors anymore.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to handle minimum and maximum firmware API numbers convert
the firmware fetch functionality to a loop. If no firmware image is found print
an error with minimum and maximum API numbers and the name of firmware
directory. This is needed when we switch to using request_firmware_direct()
which doesn't print any errors anymore.
Also add a new function for creating the fw file name dynamically which makes it
easier to add new bus support, for example SDIO and USB, later.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[kvalo@qca.qualcomm.com: remove sdio/usb part, new error message, clarify commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes the below crash when ath10k probe firmware fails, NAPI polling tries
to access a rx ring resource which was never allocated. An easy way to
reproduce this is easy to remove all the firmware files, load ath10k modules
and ath10k will crash when calling 'rmmod ath10k_pci'. The fix is to call
napi_enable() from ath10k_pci_hif_start() so that it matches with
napi_disable() being called from ath10k_pci_hif_stop().
Big thanks to Mohammed Shafi Shajakhan who debugged this and provided first
version of the fix. In this patch I just fix the actual problem in pci.c
instead of having a workaround in core.c.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: __ath10k_htt_rx_ring_fill_n+0x19/0x230 [ath10k_core]
__ath10k_htt_rx_ring_fill_n+0x19/0x230 [ath10k_core]
Call Trace:
[<ffffffffa113ec62>] ath10k_htt_rx_msdu_buff_replenish+0x42/0x90
[ath10k_core]
[<ffffffffa113f393>] ath10k_htt_txrx_compl_task+0x433/0x17d0
[ath10k_core]
[<ffffffff8114406d>] ? __wake_up_common+0x4d/0x80
[<ffffffff811349ec>] ? cpu_load_update+0xdc/0x150
[<ffffffffa119301d>] ? ath10k_pci_read32+0xd/0x10 [ath10k_pci]
[<ffffffffa1195b17>] ath10k_pci_napi_poll+0x47/0x110 [ath10k_pci]
[<ffffffff817863af>] net_rx_action+0x20f/0x370
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: 3c97f5de1f ("ath10k: implement NAPI support")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I wanted to take a look and it's apparently in other header
Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cleanup to consolidate type used for len variables
Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
it adds unnecessary level of indirection, while we just access structure
field
Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix these errors reported by the 0-day builder by replacing the
linux/export.h include with linux/module.h.
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
include/linux/device.h:1463:1: warning: data definition has no type or storage class
module_init(__driver##_init); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:1463:1: error: type defaults to 'int' in declaration of 'module_init' [-Werror=implicit-int]
module_init(__driver##_init); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
include/linux/device.h:1468:1: warning: data definition has no type or storage class
module_exit(__driver##_exit);
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:1468:1: error: type defaults to 'int' in declaration of 'module_exit' [-Werror=implicit-int]
module_exit(__driver##_exit);
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_exit' defined but not used [-Wunused-function]
module_platform_driver(ath_ahb_driver);
^
include/linux/device.h:1464:20: note: in definition of macro 'module_driver'
static void __exit __driver##_exit(void) \
^~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_init' defined but not used [-Wunused-function]
module_platform_driver(ath_ahb_driver);
^
include/linux/device.h:1459:19: note: in definition of macro 'module_driver'
static int __init __driver##_init(void) \
^~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary so that - if ath10k is the only driver using
dev_coredump*() - the functionality is built into the kernel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This now declares a module parameter, so include the necessary
header file for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove redundant semicolon after switch statement.
Signed-off-by: Waldemar Rymarkiewicz <ext.waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code currently relies on refcounting to disable IRQs from within the
IRQ handler and re-enabling them again after the tasklet has run.
However, due to race conditions sometimes the IRQ handler might be
called twice, or the tasklet may not run at all (if interrupted in the
middle of a reset).
This can cause nasty imbalances in the irq-disable refcount which will
get the driver permanently stuck until the entire radio has been stopped
and started again (ath_reset will not recover from this).
Instead of using this fragile logic, change the code to ensure that
running the irq handler during tasklet processing is safe, and leave the
refcount untouched.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In an RFC patch, Sven Eckelmann and Simon Wunderlich reported:
"QCA 802.11n chips (especially AR9330/AR9340) sometimes end up in a
state in which a read of AR_CFG always returns 0xdeadbeef.
This should not happen when when the power_mode of the device is
ATH9K_PM_AWAKE."
Include the check for the default register state in the existing MAC
hang check.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Also include common MAC alive check. This should make the hang checks
more reliable for modes where beacons are not sent and is used as a
starting point for further hang check improvements
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the even that the wcn36xx interface is brought down while a hw_scan
is active we must abort and wait for the ongoing scan to signal
completion to mac80211.
Reported-by: Mart Raudsepp <leio@gentoo.org>
Fixes: 886039036c ("wcn36xx: Implement firmware assisted scan")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.
While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110
Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95
Avoiding these configurations while bringing the target in
testmode is solving the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch provides support to get per peer tids log.
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/
XX:XX/peer_debug_trigger
These logs will be the part of FWLOGS which we collect the logs
via tracing interface. Here we will get the peer tigd logs only
once(not repeatedly) when we write 1 to the debugfs file.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:1593: Statements should start on a tabstop
drivers/net/wireless/ath/ath10k/ce.c:962: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1823: function definition argument 'struct sk_buff *' should also have an identifier name
drivers/net/wireless/ath/ath10k/wmi.h:6607: function definition argument 'struct wmi_start_scan_arg *' should also have an identifier name
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1639: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/net/wireless/ath/ath10k/htt.h:1660: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYkafBAAoJEG4XJFUm622b0EAH/3mFY0WDfdR/Ych29HX1M/Ao
Bd5gQfKzHS8ANR56qqmxEbpLdBnBa8iNC0IS4RFsWVv6qMoEEOHDLeY5W9XsomWK
i45fQN2XIdjBUOyDXUjsyz006cMe79VzRvFf9gfSekP8i8BCWQzyYC8VKt/F+6Sh
yo9yA4Yv3zA3mA3yRKtxSjLm/6xUXCFVNshKGT0rXc/oEfIN6OnIC1k0p0xw2hhl
GyLN6PSGOqcJc91+IoGOg4TaHzPdWJcWatuxGdQn8gKSDg0+gXaNh9Gtf4H/ojqp
Fwt2Ckk5mgJYk/2TAuFRpRXNMTJznUhp4Tjp2AE7EVM0f5JujUbQuPblOVfLIYk=
=vKKN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified, among others, by device and sybsystem ids.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
To solve the issue QCA uses SMBIOS type 0xF8 to store Board Data File Name
Extension to specify the extension/variant name. The driver will take the
extension suffix into consideration and will load the right (non-default)
board data file if necessary.
If it is unnecessary to use extension board data file, please leave the
SMBIOS field blank and default configuration will be used.
Example:
If a default board data file for a specific board is identified by a string
"bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,
subsystem-device=0310"
then the OEM specific data file, if used, could be identified by variant
suffix:
"bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,
subsystem-device=0310,variant=DE_1AB"
Signed-off-by: Waldemar Rymarkiewicz <ext.waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CORE_CTRL_ADDRESS is offset in register address space, it does not
make sense to OR it to derive the final address. It looks like its
a typo, so fix it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
use dma_zalloc_coherent() instead of dma_alloc_coherent and memset().
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
DIAG_TRANSFER_LIMIT is redefined with same value and comments
just below this entry, remove this duplicate entry.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Symbolic permissions are no longer recommended.
This patch changes the symbolic permissions in wil6210 driver
to octal permissions.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add an option to specify and override the A-BFT length when
starting an AP/PCP. See IEEE P802.11-2016, 10.38.5.
The abft_len must be set before starting AP/PCP. It is only
needed for diagnostics and certification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add reporting of the association ID (AID) for each station
as part of the stations file in the debugfs.
Valid AID values are 1-254. 0 is reported if the AID
is unknown or not reported by firmware.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently we do not have full support for broadcast from
a station inside a PBSS network.
We have a workaround where instead of broadcast we do a
unicast to every known station in the PBSS.
This workaround was performed only for P2P clients.
This fix will perform the broadcast workaround also for a
regular station inside a PBSS.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During reset sequence it is seen that device is generating an
interrupt eventhough interrupts are masked at device level.
Add workaround to disable the interrupts from host side during
reset and clear any pending interrupts before re-enabling
the interrupt.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code in wmi_call uses the wil->wmi_call completion
structure to wait for a reply.
In some scenarios, complete was called twice on the
completion structure. This happened mainly with a disconnect
event which can arrive both unsolicited and as a reply to
a disconnect request. In this case the completion structure
was left marked as "done" and the next wmi_call returned
immediately with a corrupted reply buffer. This caused
unexpected results including crashes.
Fix this by adding the missing call to reinit_completion.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_ONLY FW is used for testing in production. It cannot be used for
scan/connect, etc.
In case FW reports this capability, driver will not allow interface up.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
__func__ is automatically added to printouts by dynamic debug
mechanism and by wil_info/wil_err macros.
Remove __func__ from debug printouts to avoid duplication.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver may be used in platforms where some use sparrow cards while
other use sparrow-plus cards, where different FW image is needed.
Add the capability to load dedicated FW image in case sparrow-plus
card is detected and fallback to default image if such does not exist.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By default, AP SME is handled by driver/FW.
In case disable_ap_sme is true, driver doesn't turn-on
WIPHY_FLAG_HAVE_AP_SME and the responsibility for
AP SME is passed to user space.
With AP SME disabled, driver reports assoc request frame
to user space which is then responsible for sending assoc
response frame and for sending NL80211_CMD_NEW_STATION.
Driver also reports disassoc frame to user space
which should then send NL80211_CMD_DEL_STATION.
NL80211_CMD_SET_STATION with NL80211_STA_FLAG_AUTHORIZED
is used by user space to allow/disallow data transmit.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not clearing the previous tx bit rate status
results in a ambigous tx bit rate reporting to
mac80211/cfg80211, for example the previous bit
rate status would have been marked as legacy rate
, while the current rate would have been an HT/VHT
rate with the tx bit rate flags set and this results
in exporting tx bitrate as legacy rate but with HT/VHT
rate flags set, fix this by clearing the tx bitrate
status for each event. This also fixes the below
warning when we do:
iw dev wlan#N station dump
WARNING: net/wireless/util.c:1222 cfg80211
[<c022f104>] (warn_slowpath_null) from [<bf3b9adc>]
(cfg80211_calculate_bitrate+0x110/0x1f4 [cfg80211])
[<bf3b9adc>] (cfg80211_calculate_bitrate [cfg80211]) from
[<bf3dcd54>] (nl80211_put_sta_rate+0x44/0x1dc [cfg80211])
[<bf3dcd54>] (nl80211_put_sta_rate [cfg80211]) from
[<bf3cbc34>] (nl80211_set_interface+0x724/0xd70 [cfg80211])
[<bf3cbc34>] (nl80211_set_interface [cfg80211]) from
[<bf3d0a18>] (nl80211_dump_station+0xdc/0x100 [cfg80211])
[<bf3d0a18>] (nl80211_dump_station [cfg80211])
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Station pointers are RCU protected so driver must
be extra careful if it tries to store them
internally for later use outside of the RCU
section it obtained it in.
It was possible for station teardown to race with
some htt events. The possible outcome could be a
use-after-free and a crash.
Only peer-flow-control capable firmware was
affected (so hardware-wise qca99x0 and qca4019).
This could be done in sta_state() itself via
explicit synchronize_net() call but there's
already a convenient sta_pre_rcu_remove() op that
can be hooked up to avoid extra rcu stall.
The peer->sta pointer itself can't be set to
NULL/ERR_PTR because it is later used in
sta_state() for extra sanity checks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes the following sparse warning:
drivers/net/wireless/ath/ath6kl/sdio.c:716:55: warning:
Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
-----BEGIN PGP SIGNATURE-----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=UToW
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx legacy rate is reported 10 fold, as below
iw dev wlan#N station dump | grep "tx bitrate"
tx bitrate: 240.0 MBit/s
This is because by mistake we multiply by the hardware reported
rate twice by 10, fix this.
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In countries where basic operation of channel 169 is allowed,
this fixes the below WARN_ON_ONCE in Rx and fixes the station
connectivity failure in channel 169 as the packet is dropped
in the driver as the current check limits to channel 165. As of
now all the packets beyond channel 165 is dropped, fix this
by extending the range to channel 169.
Call trace:
drivers/net/wireless/ath/ath10k/wmi.c:1505
ath10k_wmi_event_mgmt_rx+0x278/0x440 [ath10k_core]()
Call Trace:
[<c158f812>] ? printk+0x2d/0x2f
[<c105a182>] warn_slowpath_common+0x72/0xa0
[<f8b67b58>] ? ath10k_wmi_event_mgmt_rx+0x278/0x440
[<f8b67b58>] ? ath10k_wmi_event_mgmt_rx+0x278/0x440
[<c105a1d2>] warn_slowpath_null+0x22/0x30
[<f8b67b58>] ath10k_wmi_event_mgmt_rx+0x278/0x440
[<f8b0e72b>] ? ath10k_pci_sleep+0x8b/0xb0 [ath10k_pci]
[<f8b6ac63>] ath10k_wmi_10_2_op_rx+0xf3/0x3b0
[<f8b6495e>] ath10k_wmi_process_rx+0x1e/0x60
[<f8b5f077>] ath10k_htc_rx_completion_handler+0x347/0x4d0 [ath10k_core]
[<f8b11dc3>] ? ath10k_ce_completed_recv_next+0x53/0x70 [ath10k_pci]
[<f8b0f921>] ath10k_pci_ce_recv_data+0x171/0x1d0 [ath10k_pci]
[<f8b0ec69>] ? ath10k_pci_write32+0x39/0x80 [ath10k_pci]
[<f8b120bc>] ath10k_ce_per_engine_service+0x5c/0xa0 [ath10k_pci]
[<f8b1215f>] ath10k_ce_per_engine_service_any+0x5f/0x70 [ath10k_pci]
[<c1060dc0>] ? local_bh_enable_ip+0x90/0x90
[<f8b1048b>] ath10k_pci_tasklet+0x1b/0x50 [ath10k_pci]
Fixes: 34c30b0a5e ("ath10k: enable advertising support for channel 169, 5Ghz")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently, the common ath9k_common module needs to have a
dependency on RELAY and DEBUG_FS in order to built. This
is usually not a problem. But for RAM and FLASH starved
AR71XX devices, every little bit counts.
This patch adds a new symbol CONFIG_ATH9K_COMMON_DEBUG
which makes it possible to drop the RELAY and DEBUG_FS
dependency there and move it to ATH_(HTC)_DEBUGFS.
Note: The shared FFT/spectral code (which is the only user
of the relayfs in ath9k*) needs DEBUG_FS to export the relayfs
interface to dump the data to userspace. So it makes no sense
to have the functions compiled in, if DEBUG_FS is not there.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.4 firmware adds extended peer information to the
firmware's statistics payload. This additional info is
stored as a separate data field and the elements are
stored in their own "peers_extd" list.
These elements can pile up in the same way as the peer
information elements. This is because the
ath10k_wmi_10_4_op_pull_fw_stats() function tries to
pull the same amount (num_peer_stats) for every statistic
data unit.
Fixes: 4a49ae94a4 ("ath10k: fix 10.4 extended peer stats update")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds full VHT160 support for QCA9984 chipsets Tested on Netgear
R7800. 80+80 is possible, but disabled so far since it seems to contain
glitches like missing vht station flags (this may be firmware or mac80211
related).
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
[kvalo@qca.qualcomm.com: refactoring and fix few warnings]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When adding VHT160 support to ath10k_peer_assoc_h_phymode() the VHT mode
selection code becomes too complex. Simplify it by refactoring the vht part to
a separate function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trivial fix to spelling mistake in ath_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't currently harmful.
However, for some new features (e.g. KTSAN / Kernel Thread Sanitizer),
it is necessary to instrument reads and writes separately, which is not
possible with ACCESS_ONCE(). This distinction is critical to correct
operation.
It's possible to transform the bulk of kernel code using the Coccinelle
script below. However, for some files (including the ath9k ar9003 mac
driver), this mangles the formatting. As a preparatory step, this patch
converts the driver to use {READ,WRITE}_ONCE() without said mangling.
----
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: ath9k-devel@qca.qualcomm.com
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: ath9k-devel@lists.ath9k.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't currently harmful.
However, for some new features (e.g. KTSAN / Kernel Thread Sanitizer),
it is necessary to instrument reads and writes separately, which is not
possible with ACCESS_ONCE(). This distinction is critical to correct
operation.
It's possible to transform the bulk of kernel code using the Coccinelle
script below. However, for some files (including the ath9k ar9002 mac
driver), this mangles the formatting. As a preparatory step, this patch
converts the driver to use {READ,WRITE}_ONCE() without said mangling.
----
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: ath9k-devel@qca.qualcomm.com
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: ath9k-devel@lists.ath9k.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simply return -EOPNOTSUPP instead.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211_ops structures are only passed as an argument to the function
wiphy_new. This argument is of type const, so cfg80211_ops strutures
having this property can be declared as const.
Done using Coccinelle
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct cfg80211_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
wiphy_new(&i@p,...)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct cfg80211_ops i;
File size before:
text data bss dec hex filename
18133 6632 0 24765 60bd wireless/ath/wil6210/cfg80211.o
File size after:
text data bss dec hex filename
18933 5832 0 24765 60bd wireless/ath/wil6210/cfg80211.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simplified transmit credit distribution code somewhat.
Since the WMI control service will get assigned all credits
there is no need for having a credit_allocation array in
struct ath10k_htc.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Removed tx_credits_per_max_message and tx_credit_size
from struct ath10k_htc_ep since they are not used
anywhere in the code.
They are just written, never read.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ieee80211_unregister_hw() might invoke operations to stop the interface,
that uses the hal_mutex. So don't destroy it until after we're done
using it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware versions sends a "print register indication", handle this
by printing out the content.
Cc: Nicolas Dechesne <ndec@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using the software based channel scan mechanism from mac80211 keeps us
offline for 10-15 second, we should instead issue a start_scan/end_scan
on each channel reducing this time.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The wcn36xx wifi driver follows the life cycle of the WLAN_CTRL SMD
channel, as such it should be a SMD client. This patch makes this
transition, now that we have the necessary frameworks available.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYalDTAAoJEG4XJFUm622ba2EH/ivoHG9CvmT6HgNw77odDr6b
Zc7plDi2dd9LIzp3rF/9j8Ietfzpu31Pp9Qz0o1Su/s8RJIlXKVF5UeG5IignnEG
02rv7Z+BGPW7SUNDb0cLa27PMYqUAh8vI39sxYSdQ9NQLIlpMLIxxx5iOZyAK5eV
HBRS0pVlSxbAntb1JgWiN/LjjXe/PdhX3CR/b9b468KAcWB6UWj9nXQxFmz7d3uM
dH3buDTgwaq7K24ZAFc1BsD7rgxprpauXxgIMWCKxRERf64WFfYkYdfdCER+PSPH
maV5Te1KzTJBrQHDOPs1ezVe8gDUhb5YE4BJY9SppZpOE1arucq2g3+3obQUeHE=
=DAVq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable advertising support for channel 169, 5Ghz so that
based on the regulatory domain(country code) this channel
shall be active for use. For example in countries like India
this channel shall be available for use with latest regulatory updates
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_mac_tx' does not seems to use the per station table
entry pointer 'sta' (struct ieee80211_sta), hence remove passing
this unused argument
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With command to get board_id from otp, in the case of following
boot get otp board id result 0x00000000 board_id 0 chip_id 0
boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0"
...
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from
ath10k/QCA6174/hw3.0/board-2.bin
The invalid board_id=0 will be used as index to search in the board-2.bin.
Ignore the case with board_id=0, as it means the otp is not carrying
the board id information.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The txpower is being recalculated when adding interface to make sure
txpower won't overshoot the spec, and when removing the interface,
the txpower should again to be recalculated to restore the correct value
from the active interface list.
Following is one of the scenario
vdev0 is created as STA and connected: txpower:23
vdev1 is created as P2P_DEVICE for control interface: txpower:0
vdev2 is created as p2p go/gc interface: txpower is 21
So the vdev2@txpower:21 will be set to firmware when vdev2 is created.
When we tear down the vdev2, the txpower needs to be recalculated to
re-set it to vdev0@txpower:23 as vdev0/vdev1 are the active interface.
ath10k_pci mac vdev 0 peer create 8c:fd:f0:01:62:98
ath10k_pci mac vdev_id 0 txpower 23
... (adding interface)
ath10k_pci mac vdev create 2 (add interface) type 1 subtype 3
ath10k_pci mac vdev_id 2 txpower 21
ath10k_pci mac txpower 21
... (removing interface)
ath10k_pci mac vdev 2 delete (remove interface)
ath10k_pci vdev 1 txpower 0
ath10k_pci vdev 0 txpower 23
ath10k_pci mac txpower 23
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Whenever firmware crashes, and both CONFIG_ATH10K_DEBUGFS and
CONFIG_ALLOW_DEV_COREDUMP are enabled, dump information about the crash via a
devcoredump device. Dump can be read from userspace for further analysis from:
/sys/class/devcoredump/devcd*/data
As until now we have provided the firmware crash dump file via fw_crash_dump
debugfs keep it still available but deprecate and a warning print that the user
should switch to using dev_coredump.
Future improvement would be not to depend on CONFIG_ATH10K_DEBUGFS, as there
might be systems which want to get the firmware crash dump but not enable
debugfs. How to handle memory consumption is also something which needs to be
taken into account.
Signed-off-by: Arun Khandavalli <akhandav@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: rebase, fixes, improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
...
ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm
ath10k_pci mac vdev_id 0 txpower 21
ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align it with the cts protection call.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The cts protection vdev parameter, in new QCA9377 TF2.0 firmware,
requires bss peer to be created for the STATION vdev type.
bss peer is being allocated by the firmware after vdev_start/_up commands.
mac80211 may call the cts protection setup at any time, so the
we needs to track the situation and defer the cts configuration
to prevent firmware asserts, like below:
[00]: 0x05020001 0x000015B3 0x0099ACE2 0x00955B31
[04]: 0x0099ACE2 0x00060730 0x00000004 0x00000000
[08]: 0x0044C754 0x00412C10 0x00000000 0x00409C54
[12]: 0x00000009 0x00000000 0x00952F6C 0x00952F77
[16]: 0x00952CC4 0x00910712 0x00000000 0x00000000
[20]: 0x4099ACE2 0x0040E858 0x00421254 0x004127F4
[24]: 0x8099B9B2 0x0040E8B8 0x00000000 0xC099ACE2
[28]: 0x800B75CB 0x0040E8F8 0x00000007 0x00005008
[32]: 0x809B048A 0x0040E958 0x00000010 0x00433B10
[36]: 0x809AFBBC 0x0040E9A8 0x0042BB74 0x0042BBBC
[40]: 0x8091D252 0x0040E9C8 0x0042BBBC 0x00000001
[44]: 0x809FFA45 0x0040EA78 0x0043D3E4 0x0042C2C8
[48]: 0x809FCEF4 0x0040EA98 0x0043D3E4 0x00000001
[52]: 0x80911210 0x0040EAE8 0x00000010 0x004041D0
[56]: 0x80911154 0x0040EB28 0x00400000 0x00000000
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The correct number for QCA9377 chip is 33 VDEVs.
This impacts also QCA6174 chip and it's max VDEV number.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Similarly to QCA6174, QCA9377 requires the CE5 configuration to be
available for other feature. Use the ath10k_pci_override_ce_config()
for it as well.
This is required for TF2.0 firmware. Previous FW revisions were
working fine without this patch.
Fixes: a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
That's the default now, no need for makefiles to set it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
'ath10k_htt_tx_free_cont_txbuf' and 'ath10k_htt_tx_free_cont_frag_desc'
have NULL pointer checks to avoid crash if they are called twice
but this is as of now not sufficient as these pointers are not assigned
to NULL once the contiguous DMA memory allocation is freed, fix this.
Though this may not be hit with the explicity check of state variable
'tx_mem_allocated' check, good to have this addressed as well.
Below BUG_ON is hit when the above scenario is simulated
with kernel debugging enabled
page:f6d09a00 count:0 mapcount:-127 mapping: (null)
index:0x0
flags: 0x40000000()
page dumped because: VM_BUG_ON_PAGE(page_ref_count(page)
== 0)
------------[ cut here ]------------
kernel BUG at ./include/linux/mm.h:445!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
EIP is at put_page_testzero.part.88+0xd/0xf
Call Trace:
[<c118a2cc>] __free_pages+0x3c/0x40
[<c118a30e>] free_pages+0x3e/0x50
[<c10222b4>] dma_generic_free_coherent+0x24/0x30
[<f8c1d9a8>] ath10k_htt_tx_free_cont_txbuf+0xf8/0x140
[<f8c1e2a9>] ath10k_htt_tx_destroy+0x29/0xa0
[<f8c143e0>] ath10k_core_destroy+0x60/0x80 [ath10k_core]
[<f8acd7e9>] ath10k_pci_remove+0x79/0xa0 [ath10k_pci]
[<c13ed7a8>] pci_device_remove+0x38/0xb0
[<c14d3492>] __device_release_driver+0x72/0x100
[<c14d36b7>] driver_detach+0x97/0xa0
[<c14d29c0>] bus_remove_driver+0x40/0x80
[<c14d427a>] driver_unregister+0x2a/0x60
[<c13ec768>] pci_unregister_driver+0x18/0x70
[<f8aced4f>] ath10k_pci_exit+0xd/0x2be [ath10k_pci]
[<c1101e78>] SyS_delete_module+0x158/0x210
[<c11b34f1>] ? __might_fault+0x41/0xa0
[<c11b353b>] ? __might_fault+0x8b/0xa0
[<c1001a4b>] do_fast_syscall_32+0x9b/0x1c0
[<c178da34>] sysenter_past_esp+0x45/0x74
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These are one-line functions that just call spin_lock/unlock_bh(); turn
them into static inlines to avoid the function call overhead.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reworks the ath9k driver to schedule transmissions to connected
stations in a way that enforces airtime fairness between them. It
accomplishes this by measuring the time spent transmitting to or
receiving from a station at TX and RX completion, and accounting this to
a per-station, per-QoS level airtime deficit. Then, an FQ-CoDel based
deficit scheduler is employed at packet dequeue time, to control which
station gets the next transmission opportunity.
Airtime fairness can significantly improve the efficiency of the network
when station rates vary. The following throughput values are from a
simple three-station test scenario, where two stations operate at the
highest HT20 rate, and one station at the lowest, and the scheduler is
employed at the access point:
Before / After
Fast station 1: 19.17 / 25.09 Mbps
Fast station 2: 19.83 / 25.21 Mbps
Slow station: 2.58 / 1.77 Mbps
Total: 41.58 / 52.07 Mbps
The benefit of airtime fairness goes up the more stations are present.
In a 30-station test with one station artificially limited to 1 Mbps,
we have seen aggregate throughput go from 2.14 to 17.76 Mbps.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ar9300_eeprom logic is already using only 8-bit (endian neutral),
__le16 and __le32 fields to state explicitly how the values should be
interpreted.
All other EEPROM implementations (4k, 9287 and def) were using u16 and
u32 fields with additional logic to swap the values (read from the
original EEPROM) so they match the current CPUs endianness.
The EEPROM format defaults to "all values are Little Endian", indicated
by the absence of the AR5416_EEPMISC_BIG_ENDIAN in the u8 EEPMISC
register. If we detect that the EEPROM indicates Big Endian mode
(AR5416_EEPMISC_BIG_ENDIAN is set in the EEPMISC register) then we'll
swap the values to convert them into Little Endian. This is done by
activating the EEPMISC based logic in ath9k_hw_nvram_swap_data even if
AH_NO_EEP_SWAP is set (this makes ath9k behave like the FreeBSD driver,
which also does not have a flag to enable swapping based on the
AR5416_EEPMISC_BIG_ENDIAN bit). Before this logic was only used to
enable swapping when "current CPU endianness != EEPROM endianness".
After changing all relevant fields to __le16 and __le32 sparse was used
to check that all code which reads any of these fields uses
le{16,32}_to_cpu.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are two ways of swapping the EEPROM data in the ath9k driver:
1) swab16 based on the first two EEPROM "magic" bytes (same for all
EEPROM formats)
2) field and EEPROM format specific swab16/swab32 (different for
eeprom_def, eeprom_4k and eeprom_9287)
The result of the first check was used to also enable the second swap.
This behavior seems incorrect, since the data may only be byte-swapped
(afterwards the data could be in the correct endianness).
Thus we introduce a separate check based on the "eepmisc" register
(which is part of the EEPROM data). When bit 0 is set, then the EEPROM
format specific values are in "big endian". This is also done by the
FreeBSD kernel, see [0] for example.
This allows us to parse EEPROMs with the "correct" magic bytes but
swapped EEPROM format specific values. These EEPROMs (mostly found in
lantiq and broadcom based big endian MIPS based devices) only worked
due to platform specific "hacks" which swapped the EEPROM so the
magic was inverted, which also enabled the format specific swapping.
With this patch the old behavior is still supported, but neither
recommended nor needed anymore.
[0]
50719b56d9/sys/dev/ath/ath_hal/ah_eeprom_9287.c (L351)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The AR5416_VER_MASK macro does the same as get_eeprom_rev, except that
one has to know the actual EEPROM type (and providing a reference to
that in a variable named "eep"). Additionally the eeprom_*.c
implementations used the same shifting logic multiple times to get the
eeprom revision which was also unnecessary duplication of
get_eeprom_rev.
Also use the AR5416_EEP_VER_MINOR_MASK macro where needed and introduce
a similar macro (AR5416_EEP_VER_MAJOR_MASK) for the major version.
Finally drop AR9287_EEP_VER_MINOR_MASK since it simply duplicates the
already defined AR5416_EEP_VER_MINOR_MASK.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
get_eeprom(ah, EEP_MINOR_REV) and get_eeprom_rev(ah) are both doing the
same thing: returning the EEPROM revision (12 lowest bits). Make the
code consistent by using get_eeprom_rev(ah) everywhere.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows deciding if we have to swap the EEPROM data (so it matches
the system's native endianness) even if no byte-swapping (swab16, based on
the first two bytes in the EEPROM) is needed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The eepMisc field was not set explicitly. The default value of 0 means
that the values in the EEPROM (template) should be interpreted as little
endian. However, this is not clear until comparing the AR9003 code with
the other EEPROM formats.
To make the code easier to understand we explicitly state that the values
are little endian - there are no functional changes with this patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This replaces a magic number with a named #define. Additionally it
removes two "eeprom format" specific #defines for the "big endianness"
bit which are the same on all eeprom formats.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The comment on the name indirection suggested an issue but turned out
to be untrue. Digging in older kernel version showed issue with ipw2x00
but that is no longer true so get rid on the name indirection.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYQGivAAoJEG4XJFUm622bqG0IAJtSGt4Fxv2jL7GPmPpEUtYK
F6G1PCk9LxO44rOZ15E/CT1vPk6Bnwqp9brdngmXwl7jc+jGs4MQN7g6cD4UZgPm
gxjx8cah2HPRVgEE7PeOILthRxwPA+9klycsvwtglkgQ1SpQVmLHDTLpeOAkRluY
olJGINoGHTD6osud6p3oKK+VP891omJvu8TPqRjhrhLhbQTWAuTxl2Gsdye30yag
CsdaEZb9wdUEBoS80EVRwvgBzqrdKU5kGDGbuzytcyrFrRHo4flti1KgxDg3nIpI
jC4Liwg0yE/aYZlfMqi/960rt8AttCJBDt/vwqp0mOE4IwFsE9Yaio6xXUonAC8=
=a6a/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate header vmalloc.h from ath5k/debug.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added new areas to fw_mappings area for UCODE code
and data areas.
The new areas are only exposed through debugfs blobs,
and mainly needed to access UCODE logs.
The change does not affect crash dumps because the
newly added areas overlap with the "upper" area which
is already dumped.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
num_descriptors and descriptor_size needs to be
checked for:
1) not being negative values
2) no overflow occurs when these are multiplied
together as done in wil_pmc_read.
An overflow of two signed integers is undefined
behavior.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently it was possible to call remain_on_channel(ROC)
while scan was active and this caused a crash in the FW.
In order to fix this problem and make the behavior
consistent with other drivers, queue the ROC in case
a scan is active and try it again when scan is done.
As part of the fix, clean up some locking issues and
return error if scan is called while ROC is active.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The usb_*_msg() functions expect a timeout in msecs but are given HZ,
which is ticks per second. If HZ=100, firmware download often times out
when there is modest USB utilization and the device fails to initialize.
Replaces HZ in usb_*_msg timeouts with 1000 msec since HZ is one second
for timeouts in jiffies.
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Declare the structure ath_bus_ops as const as it is only passed as an
argument to the function ath9k_init_device. This argument is of type
const struct ath_bus_ops *, so ath_bus_ops structures with this property
can be declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct ath_bus_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
expression e1,e2;
@@
ath9k_init_device(e1,e2,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct ath_bus_ops i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ath_bus_ops i;
File size before:
text data bss dec hex filename
1295 232 0 1527 5f7 ath/ath9k/ahb.o
File size after:
text data bss dec hex filename
1359 176 0 1535 5ff ath/ath9k/ahb.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These memory chunks are often used as 'swap' by the NIC,
so it will be both reading and writing to these areas.
This seems to fix errors like this on my x86-64 machine:
kernel: DMAR: DMAR:[DMA Write] Request device [05:00.0] fault addr ff5de000
DMAR:[fault reason 05] PTE Write access is not set
Tested-by: Marek Behun <kabel@blackhole.sk>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With maximum number of vap's configured in a two radio supported
systems of ~256 Mb RAM, doing a continuous wifi down/up and
intermittent traffic streaming from the connected stations results
in failure to allocate contiguous memory for tx buffers. This results
in the disappearance of all VAP's and a manual reboot is needed as
this is not a crash (or) OOM(for OOM killer to be invoked). To address
this allocate contiguous memory for tx buffers one time and re-use them
until the modules are unloaded but this results in a slight increase in
memory footprint of ath10k when the wifi is down, but the modules are
still loaded. Also as of now we use a separate bool 'tx_mem_allocated'
to keep track of the one time memory allocation, as we cannot come up
with something like 'ath10k_tx_{register,unregister}' before
'ath10k_probe_fw' is called as 'ath10k_htt_tx_alloc_cont_frag_desc'
memory allocation is dependent on the hw_param 'continuous_frag_desc'
a) memory footprint of ath10k without the change
lsmod | grep ath10k
ath10k_core 414498 1 ath10k_pci
ath10k_pci 38236 0
b) memory footprint of ath10k with the change
ath10k_core 414980 1 ath10k_pci
ath10k_pci 38236 0
Memory Failure Call trace:
hostapd: page allocation failure: order:6, mode:0xd0
[<c021f150>] (__dma_alloc_buffer.isra.23) from
[<c021f23c>] (__alloc_remap_buffer.isra.26+0x14/0xb8)
[<c021f23c>] (__alloc_remap_buffer.isra.26) from
[<c021f664>] (__dma_alloc+0x224/0x2b8)
[<c021f664>] (__dma_alloc) from [<c021f810>]
(arm_dma_alloc+0x84/0x90)
[<c021f810>] (arm_dma_alloc) from [<bf954764>]
(ath10k_htt_tx_alloc+0xe0/0x2e4 [ath10k_core])
[<bf954764>] (ath10k_htt_tx_alloc [ath10k_core]) from
[<bf94e6ac>] (ath10k_core_start+0x538/0xcf8 [ath10k_core])
[<bf94e6ac>] (ath10k_core_start [ath10k_core]) from
[<bf947eec>] (ath10k_start+0xbc/0x56c [ath10k_core])
[<bf947eec>] (ath10k_start [ath10k_core]) from
[<bf8a7a04>] (drv_start+0x40/0x5c [mac80211])
[<bf8a7a04>] (drv_start [mac80211]) from [<bf8b7cf8>]
(ieee80211_do_open+0x170/0x82c [mac80211])
[<bf8b7cf8>] (ieee80211_do_open [mac80211]) from
[<c056afc8>] (__dev_open+0xa0/0xf4)
[21053.491752] Normal: 641*4kB (UEMR) 505*8kB (UEMR) 330*16kB (UEMR)
126*32kB (UEMR) 762*64kB (UEMR) 237*128kB (UEMR) 1*256kB (M) 0*512kB
0*1024kB 0*2048kB 0*4096kB = 95276kB
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During firmware crash (or) user requested manual restart
the system gets into a soft lock up state because of the
below root cause.
During user requested hardware restart / firmware crash
the system goes into a soft lockup state as 'napi_synchronize'
is called after 'napi_disable' (which sets 'NAPI_STATE_SCHED'
bit) and it sleeps into infinite loop as it waits for
'NAPI_STATE_SCHED' to be cleared. This condition is hit because
'ath10k_hif_stop' is called twice as below (resulting in calling
'napi_synchronize' after 'napi_disable')
'ath10k_core_restart' -> 'ath10k_hif_stop' (ATH10K_STATE_ON) ->
-> 'ieee80211_restart_hw' -> 'ath10k_start' -> 'ath10k_halt' ->
'ath10k_core_stop' -> 'ath10k_hif_stop' (ATH10K_STATE_RESTARTING)
Fix this by calling 'ath10k_halt' in ath10k_core_restart itself
as it makes more sense before informing mac80211 to restart h/w
Also remove 'ath10k_halt' in ath10k_start for the state of 'restarting'
Fixes: 3c97f5de1f ("ath10k: implement NAPI support")
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a typo bug in the current implementation of
ath10k_wmi_tlv_op_gen_pdev_set_rd.
The conformance test limits are not set up properly.
The two arguments ctl2g and ctl5g were not used at all.
Instead, the regdomain arguments rd2g and rd5g were used
for the ctl settings as well.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Radar pulse and spectral scan reports are provided by the HW
with the ATH9K_RXERR_PHY flag set. Those are forwarded to
the dfs-detector and spectral module for further processing.
For some older chips, the pre-conditions checked in those
modules are ambiguous, since ATH9K_PHYERR_RADAR is used to
tag both types. As a result, spectral frames are fed into
the dfs-detector and vice versa.
This could lead to a false radar detection on a non-DFS
channel (which is uncritical), but more relevant it causes
useless CPU load for processing invalid frames.
This commit ensures that the dfs-detector and spectral
collector are only fed when they are active.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to receive other BSS entries in mesh mode, Monitor vdev
is created whenever filter flag is set with OTHER_BSS. Recently
it is root caused that setting promisc filter for Mesh interface
is causing performance and stability issues. To fix this issue,
firmware will configure appropriate rxfilters by default for mesh
vdev during vdev creation. This change fixes monitor vdev creation
based on firmware IE
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per STA tx bitrate info is filled from peer stats.
Export per sta txrate info to cfg80211/nl80211
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per peer tx stats are part of 'HTT_10_4_T2H_MSG_TYPE_PEER_STATS'
event, Firmware sends one HTT event for every four PPDUs.
HTT payload has success pkts/bytes, failed pkts/bytes, retry
pkts/bytes and rate info per ppdu.
Peer stats are enabled through 'WMI_SERVICE_PEER_STATS',
which are nowadays enabled by default.
Parse peer stats and update the tx rate information per STA.
tx rate, Peer stats are tested on QCA4019 with Firmware version
10.4-3.2.1-00028.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for setting retry limit for short frames,
using NL80211_CMD_SET_WIPHY with the attribute
NL80211_ATTR_WIPHY_RETRY_SHORT.
Update wiphy->retry_short from the FW default when interface
is brought up.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Implement cfg80211 abort_scan op to allow the upper layer to
abort an ongoing scan request.
In addition, notify wil6210 device on scan abort request instead
of just ignoring the scan response.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW crashes with no_fw_recovery option, driver
waits for manual recovery with wil->mutex held, this
can easily create deadlocks.
Fix the problem by moving the wait outside the lock.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New power management wmi commands provide the ability to change
the device power save profile (enable / disable power save).
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver calls to netif_tx_stop_all_queues/netif_tx_wake_all_queues are
inconsistent. In several cases, driver can get to a situation where net
queues are stopped forever and data cannot be sent.
The fix is to stop net queues if there is at least one vring which is
"full" and to wake net queues if all vrings are not "full".
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit b2d70d4944 ("ath9k: make GPIO API to support both of WMAC and
SOC") refactored ath9k_hw_gpio_get() to support both WMAC and SOC GPIOs,
changing the return on success from 1 to BIT(gpio). This broke some callers
like ath_is_rfkill_set(). This doesn't fix any known bug in mainline at the
moment, but should be fixed anyway.
Instead of fixing all callers, change ath9k_hw_gpio_get() back to only
return 0 or 1.
Fixes: b2d70d4944 ("ath9k: make GPIO API to support both of WMAC and SOC")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
[kvalo@qca.qualcomm.com: mention that doesn't fix any known bug]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Command structure and event flow doesn't seem to
be any different compared to existing
implementation for other firmware branches.
This patch effectively adds in-driver support for
spectral scanning on QCA61x4 and QCA9377.
Tested QCA9377 w/ WLAN.TF.1.0-00267-1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Neither of these did the right thing:
- get_tsf just returned 0
- set_tsf assumed a simple offset was applied against
get_tsf(), which works, except in the case of
calculating TSF from rx_mactime (actual TSF).
Just remove them for now. We can reimplement set_tsf in
terms of TSF increment/decrement in the future if get_tsf
is ever supported by FW.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current set_tsf is implemented in terms of TSF_INCREMENT
only. Instead support new WMI command TSF_DECREMENT and
export these through offset_tsf. Advantage is we get
more accurate TSF adjustments, and don't calculate wrong
offset in case absolute TSF was calculated from rx_mactime
(actual TSF).
The new WMI command is available in firmware
10.4-3.2.1-00033 for QCA4019 chips. Old drivers on new
firmware or vice versa shouldn't be a problem since
get/set tsf logic was already broken.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Indicate hardware (or firmware) supports that CQM packet-loss report
will be generated based on station kickout algorithm. As of now mac80211
tracks connection loss by missing msdu counts (50) whereas ath10k
firmware tracks them by missing ppdus (+ BAR tries). While firmware is
trying to adapt its rate table, mac80211 might send out low_ack event to
hostapd. This is causing frequent connect and disconnect iteration under
noisy environment or when station is roaming around.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.10. Major changes:
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
The hostap_80211_rx() function is supposed to set up the mac addresses
for four possible cases, based on two bits of input data. For
some reason, gcc decides that it's possible that none of the these
four cases apply and the addresses remain uninitialized:
drivers/net/wireless/intersil/hostap/hostap_80211_rx.c: In function ‘hostap_80211_rx’:
arch/x86/include/asm/string_32.h:77:14: warning: ‘src’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/wireless/intel/ipw2x00/libipw_rx.c: In function ‘libipw_rx’:
arch/x86/include/asm/string_32.h:77:14: error: ‘dst’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/include/asm/string_32.h:78:22: error: ‘*((void *)&dst+4)’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This warning is clearly nonsense, but changing the last case into
'default' makes it obvious to the compiler too, which avoids the
warning and probably leads to better object code too.
The same code is duplicated several times in the kernel, so this
patch uses the same workaround for all copies. The exact configuration
was hit only very rarely in randconfig builds and I only saw it
in three drivers, but I assume that all of them are potentially
affected, and it's better to keep the code consistent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The word "background" contains 10 characters so the third argument of
strncmp() need to be 10 in order to match this prefix correctly.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: 855aed1220 ("ath10k: add spectral scan feature")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove extraneous error message in 'ath10k_htt_tx_alloc_cont_frag_desc'
as the caller 'ath10k_htt_tx_alloc' already dumps a proper error
message
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cleanup 'ath10k_htt_tx_alloc' by introducing the API's
'ath10k_htt_tx_alloc/free_{cont_txbuf, txdone_fifo} and
re-use them whereever needed
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This partially reverts 'commit 2cdce425aa
("ath10k: Fix broken NULL func data frame status for 10.4")'
Unfortunately this breaks sending NULL func and the existing
issue of obtaining proper tx status for NULL function will be
fixed. Also update the comments for feature flag added to be
useless and not working
Fixes: 2cdce425aa "ath10k: Fix broken NULL func data frame status for
10.4"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This switches ath9k over to using the mac80211 intermediate software
queueing mechanism for data packets. It removes the queueing inside the
driver, except for the retry queue, and instead pulls from mac80211 when
a packet is needed. The retry queue is used to store a packet that was
pulled but can't be sent immediately.
The old code path in ath_tx_start that would queue packets has been
removed completely, as has the qlen limit tunables (since there's no
longer a queue in the driver to limit).
The mac80211 intermediate software queues offer significant latency
reductions, and this patch allows ath9k to realise them. The exact gains
from this varies with the test scenario, but in an access point scenario
we have seen latency reductions ranging from 1/3 to as much as an order
of magnitude. We also achieve slightly better aggregation.
Median latency (ping) figures with this patch applied at the access point,
with two high-rate stations and one low-rate station (HT20 5Ghz), running
a Flent rtt_fair_var_up test with one TCP flow and one ping flow going to
each station:
Fast station Slow station
Default pfifo_fast qdisc: 430.4 ms 638.7 ms
fq_codel qdisc on iface: 35.5 ms 211.8 ms
This patch set: 22.4 ms 38.2 ms
Median aggregation sizes over the same test:
Default pfifo_fast qdisc: 9.5 pkts 1.9 pkts
fq_codel qdisc on iface: 11.2 pkts 1.9 pkts
This patch set: 13.9 pkts 1.9 pkts
This patch is based on Tim's original patch set, but reworked quite
thoroughly.
Cc: Tim Shepard <shep@alum.mit.edu>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add missing space in a dev_err message and join wrapped text so
it does not span multiple lines. Fix spelling mistake on "unknown".
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows setting the MAC address and specifying that the firmware
will be requested from userspace (because there might not be a hardware
EEPROM connected to the chip) for ath9k based PCI devices using
the device tree.
There is some out-of-tree code to "convert devicetree to
ath9k_platform_data" (for example in OpenWrt and LEDE) which becomes
obsolete with this patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be used when the ath_bus_type has to be presented in a log
message or firmware filename.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The active_high LED of my Wistron DNMA-92 is still being recognized as
active_low on 4.7.6 mainline. When I was preparing my former commit
0f9edcdd88 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92
cards.") to fix that I must have somehow messed up with testing, because
I tested the final version of that patch before sending it, and it was
apparently working; but now it is not working on 4.7.6 mainline.
I initially added the PCI_DEVICE_SUB section for 0x0029/0x2096 above the
PCI_VDEVICE section for 0x0029; but then I moved the former below the
latter after seeing how 0x002A sections were sorted in the file.
This turned out to be wrong: if a generic PCI_VDEVICE entry (that has
both subvendor and subdevice IDs set to PCI_ANY_ID) is put before a more
specific one (PCI_DEVICE_SUB), then the generic PCI_VDEVICE entry will
match first and will be used.
With this patch, 0x0029/0x2096 has finally got active_high LED on 4.7.6.
While I'm at it, let's fix 0x002A too by also moving its generic definition
below its specific ones.
Fixes: 0f9edcdd88 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92 cards.")
Cc: <stable@vger.kernel.org> #4.7+
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
[kvalo@qca.qualcomm.com: improve the commit log based on email discussions]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.10. Major changes:
ath10k
* allow setting coverage class for first generation cards
* read regulatory domain from ACPI
ath9k
* disable RNG by default
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
-----BEGIN PGP SIGNATURE-----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=SjfQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Among various cleanups and improvements, we have the following:
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The old WDS 4-addr frame support is very limited, e.g.
* no encryption is possible on such links
* it cannot support rate/HT/VHT negotiation
* management APIs are very restricted
These make the WDS legacy mode useless in practice.
All of these are resolved by the 4-addr AP/client support,
so there's also no reason to improve WDS in the future.
Therefore, add a Kconfig option to disable legacy WDS.
This gives people an "emergency valve" while they migrate
to the better-supported 4-addr AP/client option; we plan
to remove it (and the associated cfg80211/mac80211 code,
which is the ultimate goal) in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- set max_mtu in wil6210 driver
- set max_mtu in atmel driver
- set min/max_mtu in cisco airo driver, remove airo_change_mtu
- set min/max_mtu in ipw2100/ipw2200 drivers, remove libipw_change_mtu
- set min/max_mtu in p80211netdev, remove wlan_change_mtu
- set min/max_mtu in net/mac80211/iface.c and remove ieee80211_change_mtu
- set min/max_mtu in wimax/i2400m and remove i2400m_change_mtu
- set min/max_mtu in intersil/hostap and remove prism2_change_mtu
- set min/max_mtu in intersil/orinoco
- set min/max_mtu in tty/n_gsm and remove gsm_change_mtu
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: Maya Erez <qca_merez@qca.qualcomm.com>
CC: Simon Kelley <simon@thekelleys.org.uk>
CC: Stanislav Yakovlev <stas.yakovlev@gmail.com>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mac80211 determines whether HW does fragmentation
by checking whether the set_frag_threshold callback is set
or not.
However, some drivers may want to set the HW fragmentation
capability depending on HW generation.
Allow this by checking a HW flag instead of checking the
callback.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
[added the flag to ath10k and wlcore]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wlcore
* fix a double free regression causing hard to track crashes
rtl8xxxu
* fix driver reload issues, a memory leak and an endian bug
rtlwifi
* fix a major regression introduced in 4.9 with firmware loading on
certain hardware
ath10k
* fix regression about broken cal_data debugfs file (since 4.7)
ath9k
* revert temperature compensation for AR9003+ devices, it was causing
too much problems
ath6kl
* add Dell OEM SDIO I/O for the Venue 8 Pro
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYAIKDAAoJEG4XJFUm622b7IcH/iV/mLuZ0Nyh7tsNeSElTjVc
AEFUdcxVRjM96n9K8AcHZVFqCSMggibOgulGiwHO48DLWOhOdzhffn3GZaRbHTbL
5o3d527R1kvx+UP8KIFF5MHjagMEC3/AYi417/DiCGH0BM6UcFPFxXOOWePiG0ov
Lz14xi/8AUrOnREc3TzvDsRUaI2VO3vvXq+IQtMwQBmtczeaKwjjw/RsqkCdkD70
yqiZVO7FJ3mDH1ybxmkbhlAklG7p9x01e3+gRbnKdEqYiaoYUrRGNE5wq00fuFBU
Xa3vbQa22csD2ShGHtPnZ6kg4X/q2gLmxNWl6M5TVvwUVD313AQepIcnTiHnwro=
=TI3A
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-10-14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.9
wlcore
* fix a double free regression causing hard to track crashes
rtl8xxxu
* fix driver reload issues, a memory leak and an endian bug
rtlwifi
* fix a major regression introduced in 4.9 with firmware loading on
certain hardware
ath10k
* fix regression about broken cal_data debugfs file (since 4.7)
ath9k
* revert temperature compensation for AR9003+ devices, it was causing
too much problems
ath6kl
* add Dell OEM SDIO I/O for the Venue 8 Pro
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The quality of ADC entropy is 10 bits of min-entropy for
a 32-bit value, change '(((x) * 8 * 320) >> 10)' to
'(((x) * 8 * 10) >> 5)' for easier understanding.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
arvifs list is traversed within data_lock spin_lock in tasklet
context to fill channel information from the corresponding vif.
This means any access to arvifs list for add/del operations
should also be protected with the same spin_lock to avoid the
race. Fix this by performing list add/del on arvfis within the
data_lock. This could fix kernel panic something like the below.
LR is at ath10k_htt_rx_pktlog_completion_handler+0x100/0xb6c [ath10k_core]
PC is at ath10k_htt_rx_pktlog_completion_handler+0x1c0/0xb6c [ath10k_core]
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[<bf4857f4>] (ath10k_htt_rx_pktlog_completion_handler+0x2f4/0xb6c [ath10k_core])
[<bf487540>] (ath10k_htt_txrx_compl_task+0x8b4/0x1188 [ath10k_core])
[<c00312d4>] (tasklet_action+0x8c/0xec)
[<c00309a8>] (__do_softirq+0xdc/0x208)
[<c0030d6c>] (irq_exit+0x84/0xe0)
[<c005db04>] (__handle_domain_irq+0x80/0xa0)
[<c00085c4>] (gic_handle_irq+0x38/0x5c)
[<c0009640>] (__irq_svc+0x40/0x74)
(gdb) list *(ath10k_htt_rx_pktlog_completion_handler+0x1c0)
0x136c0 is in ath10k_htt_rx_h_channel (drivers/net/wireless/ath/ath10k/htt_rx.c:769)
764 struct cfg80211_chan_def def;
765
766 lockdep_assert_held(&ar->data_lock);
767
768 list_for_each_entry(arvif, &ar->arvifs, list) {
769 if (arvif->vdev_id == vdev_id &&
770 ath10k_mac_vif_chan(arvif->vif, &def) == 0)
771 return def.chan;
772 }
773
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_htt_rx_h_unchain' needs to be called only if the return
value from 'ath10k_htt_rx_amsdu_pop' is 1('chained msdu's'), this
change makes it more explicit and avoids doing a skb_peek, fetching
rx descriptor pointer, checking rx msdu decap format for the case of
ret = 0 (unchained msdus). Found this change during code walk through,
not sure if this addresses any issue.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
SDIO ID 0271:0418
Signed-off-by: Alan Cox <alan@linux.intel.com>
Bugzilla-ID: https://bugzilla.kernel.org/show_bug.cgi?id=67921
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reverts commit 171f6402e4 ("ath9k_hw: implement temperature compensation
support for AR9003+"). Some users report that this commit causes a regression
in performance under some conditions.
Fixes: 171f6402e4 ("ath9k_hw: implement temperature compensation support for AR9003+")
Cc: <stable@vger.kernel.org> # 4.8
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 0b8e3c4ca2 ("ath10k: move cal data len to hw_params") broke retrieving
the calibration data from cal_data debugfs file. The length of file was always
zero. The reason is:
static ssize_t ath10k_debug_cal_data_read(struct file *file,
char __user *user_buf,
size_t count, loff_t *ppos)
{
struct ath10k *ar = file->private_data;
void *buf = file->private_data;
This is obviously bogus, private_data cannot contain both struct ath10k and the
buffer. Fix it by caching calibration data to ar->debug.cal_data. This also
allows it to be accessed when the device is not active (interface is down).
The cal_data buffer is fixed size because during the first firmware probe we
don't yet know what will be the lenght of the calibration data. It was simplest
just to use a fixed length. There's a WARN_ON() in
ath10k_debug_cal_data_fetch() if the buffer is too small.
Tested with qca988x and firmware 10.2.4.70.56.
Reported-by: Nikolay Martynov <mar.kolya@gmail.com>
Fixes: 0b8e3c4ca2 ("ath10k: move cal data len to hw_params")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
[kvalo@qca.qualcomm.com: improve commit log and minor other changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When power is removed from the device, all of the SDIO settings
return to default. Fix that by reconfiguring after power is
applied.
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows the hardware to be restarted, as it will cause the
sg to be reinitialized.
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To reuse the busreqs in case of hardware restart, they must be
properly reinitialized. If the scat_req pointer isn't reset to
0, __ath6kl_sdio_write_async() will assume there is sg work to be
done (causing a kernel OOPS).
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
Unfortunately ath10k does not generally allow modifying the coverage class
with the stock firmware and Qualcomm has so far refused to implement this
feature so that it can be properly supported in ath10k. If we however know
the registers that need to be modified for proper operation with a higher
coverage class, then we can do these modifications from the driver.
This is a hack and might cause subtle problems but as it's not enabled by
default (only when user space changes the coverage class explicitly) it should
not cause new problems for existing setups. But still this should be considered
as an experimental feature and used with caution.
This patch implements the support for first generation cards (QCA9880, QCA9887
and so on) which are based on a core that is similar to ath9k. The registers
are modified in place and need to be re-written every time the firmware sets
them. To achieve this the register status is verified after certain WMI events
from the firmware.
The coverage class may not be modified temporarily right after the card
re-initializes the registers. This is for example the case during scanning.
Thanks to Sebastian Gottschall <s.gottschall@dd-wrt.com> for initially
working on a userspace support for this. This patch wouldn't have been
possible without this documentation.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This overrides whatever regulatory the device
EEPROM contains and uses what the platform says
instead - in this implementation the ACPI driver.
In case the hint is not programmed or corrupted (0xffff)
the device falls back to the eeprom programmed settings.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
[kvalo@qca.qualcomm.com: remove ifdef, change error handling, change info messages to dbg]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will be helpful for drivers that can acquire
alpha2 regulatory codes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During offchannel scan, iw survey dump shows wrong values.
Fix this by assigning cycle counter wranarround type for
QCA9888 and QCA9884, they share same config with QCA4019.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch helps to get the TPC stats for 10.4 fw variants.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Here are the "big" driver core patches for 4.9-rc1. Also in here are a
number of debugfs fixes that cropped up due to the changes that happened
in 4.8 for that filesystem. Overall, nothing major, just a few fixes
and cleanups.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNw4PHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspLVYAoNXr
FXBHGb2tNT/1PLfvUCwd5PqWAJ9Khb5WAHtvjTmEN1zabz45aSbcrA==
=Uz6V
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are the "big" driver core patches for 4.9-rc1. Also in here are a
number of debugfs fixes that cropped up due to the changes that
happened in 4.8 for that filesystem. Overall, nothing major, just a
few fixes and cleanups.
All of these have been in linux-next with no reported issues"
* tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
drivers: dma-coherent: Move spinlock in dma_alloc_from_coherent()
drivers: dma-coherent: Fix DMA coherent size for less than page
MAINTAINERS: extend firmware_class maintainer list
debugfs: propagate release() call result
driver-core: platform: Catch errors from calls to irq_get_irq_data
sysfs print name of undiscoverable attribute group
carl9170: fix debugfs crashes
b43legacy: fix debugfs crash
b43: fix debugfs crash
debugfs: introduce a public file_operations accessor
device core: Remove deprecated create_singlethread_workqueue
drivers/base dmam_declare_coherent_memory leaks
platform: don't return 0 from platform_get_irq[_byname]() on error
cpu: clean up register_cpu func
dma-mapping: use vma_pages().
drivers: dma-coherent: use vma_pages().
attribute_container: Fix typo
base: soc: make it explicitly non-modular
drivers: base: dma-mapping: page align the size when unmap_kernel_range
platform driver: fix use-after-free in platform_device_del()
...
When building with W=1, we got one warning as belows:
drivers/net/wireless/ath/ath6kl/wmi.c:3509:6: warning: variable ‘ret’
set but not used [-Wunused-but-set-variable]
At the end of ath6kl_wmi_set_pvb_cmd, it is returned by 0 regardless of
return value of ath6kl_wmi_cmd_send.
This patch fixes return value from 0 to ret that has result of
ath6kl_wmi_cmd_send execution.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath9k RNG will dominates all the noise sources from the real HW
RNG, disable it by default. But we strongly recommand to enable
it if the system without HW RNG, especially on embedded systems.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Acked-by: Stephan Mueller <smueller@chronox.de>
Acked-by: Stephan Mueller <smueller@chronox.de>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware is running watchdog timer for tracking copy engine ring index
and write index. Whenever both indices are stuck at same location for
given duration, watchdog will be trigger to assert target. While
updating copy engine destination ring write index, driver ensures that
write index will not be same as read index by finding delta between these
two indices (CE_RING_DELTA).
HTT target to host copy engine (CE5) is special case where ring buffers
will be reused and delta check is not applied while updating write index.
In rare scenario, whenever CE5 ring is full, both indices will be referring
same location and this is causing CE ring stuck issue as explained
above. This issue is originally reported on IPQ4019 during long hour stress
testing and during veriwave max clients testsuites. The same issue is
also observed in other chips as well. Fix this by ensuring that write
index is one less than read index which means that full ring is
available for receiving data.
Cc: stable@vger.kernel.org
Tested-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ignore processing further in SWBA event scheduled for a vif, if mac80211
has marked the particular vif for stop beaconing and brought the vdev
down in 'ath10k_control_beaconing'. This should potentially avoid ath10k
warning/error messages while running continuous wifi down/up with max
number of vaps configured. Found this change during code walk through
and going through other beacon configuration related functions in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix to return a negative error code from the error handling case
instead of 0, as done elsewhere in function ath10k_ahb_probe() or
ath10k_ahb_resource_init().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The (1 << x) - 1 trick won't work when you
are trying to fill up all 64 bits, so add special
case for that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: remove the sentence about moving limits]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
They are not necessarily named in an intuitive manner,
so at least add some comments to help the next person.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipset from QCA99X0 onwards (QCA99X0, QCA9984, QCA4019 & future)
rx_hdr_status is not padded to align in 4-byte boundary. Define a
new hw_params field to handle different alignment behaviour between
different hw. This patch fixes improper retrieval of rfc1042 header
with QCA4019. This patch along with "ath10k: Properly remove padding
from the start of rx payload" will fix traffic failure in ethernet
decap mode for QCA4019.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since reset_control_get() never returns NULL, we can use IS_ERR()
instead of IS_ERR_OR_NULL(). The return statements can be simpler
as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the managed variant of reset_control_get() to simplify the
failure path and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the managed variant of clk_get() to simplify the failure path
and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Correct some trivial comment typos.
Remove unnecessary parentheses in a long line.
Signed-off-by: Joe Perches <joe@perches.com>
[kvalo@qca.qualcomm.com: drop the change for return]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ben Greear reported:
> I see lots of instability as soon as I load up the carl9710 NIC.
> My application is going to be poking at it's debugfs files...
>
> BUG: KASAN: slab-out-of-bounds in carl9170_debugfs_read+0xd5/0x2a0
> [carl9170] at addr 0xffff8801bc1208b0
> Read of size 8 by task btserver/5888
> =======================================================================
> BUG kmalloc-256 (Tainted: G W ): kasan: bad access detected
> -----------------------------------------------------------------------
>
> INFO: Allocated in seq_open+0x50/0x100 age=2690 cpu=2 pid=772
>...
This breakage was caused by the introduction of intermediate
fops in debugfs by commit 9fd4dcece4
("debugfs: prevent access to possibly dead file_operations at file open")
Thankfully, the original/real fops are still available in d_fsdata.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Cc: stable <stable@vger.kernel.org> # 4.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For structure types defined in the same file or local header files, find
top-level static structure declarations that have the following
properties:
1. Never reassigned.
2. Address never taken
3. Not passed to a top-level macro call
4. No pointer or array-typed field passed to a function or stored in a
variable.
Declare structures having all of these properties as const.
Done using Coccinelle.
Based on a suggestion by Joe Perches <joe@perches.com>.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.9. Major changes:
ath10k
* add nl80211 testmode support for 10.4 firmware
* hide kernel addresses from logs using %pK format specifier
* implement NAPI support
* enable peer stats by default
ath9k
* use ieee80211_tx_status_noskb where possible
wil6210
* extract firmware capabilities from the firmware file
ath6kl
* enable firmware crash dumps on the AR6004
ath-current is also merged to fix a conflict in ath10k.
hw_4addr_pad was added to handle different types of padding
in 4-address rx frame. But this padding is not very specific
to 4-address, it can happen even with three address + ethernet
decap mode. Since the padding information can be obtained
through Rx desc for QCA99X0 and newer chips, this hw_param
is not needed any more.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In QCA99X0 (QCA99X0, QCA9984, QCA9888 and QCA4019) family chips,
hw adds padding at the begining of the rx payload to make L3
header 4-byte aligned. In the chips doing this type of padding,
the number of bytes padded will be indicated through msdu_end:info1.
Define a hw_rx_desc_ops wrapper to retrieve the number of padded
bytes and use this while doing undecap. This should fix padding
related issues with ethernt decap format with QCA99X0, QCA9984,
QCA9888 and QCA4019 hw.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are slight differences in Rx hw descriptor information
among different chips. So far driver does not use those new
information for any functionalities, but there is one important
information which is available from QCA99X0 onwards to indicate
the number of bytes that hw padded at the begining of the rx
payload and this information is needed to undecap the rx
packet. Add an abstraction for Rx desc to make use of the
new desc information available. The callback that this patch
defines to retrieve the padding bytes will be used in follow-up
patch.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare for rx descriptor abstraction where we'll
be dereferencing ath10k_hw_params member in hw.h. Moreover
hw.h looks more suitable to house ath10k_hw_params definition
than core.h
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Helps to know the sta pointer.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: add %pK and remove the colon]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
IFTYPE_MESH_POINT need to rely on these for accurate path
selection metrics. Other modes will probably also find
them useful. Enabling peer stats has the side effect of
reducing max number of STAs from 128 to 118. There should
be negligible performance impact.
If users really need 128 STAs and don't mind losing out on
peer stats, they can still disable them:
echo 0 > debugfs/ieee80211/phyn/ath10k/peer_stats
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trival fix to remove unused variable ar_pci in ath10k_pci_tx_pipe_cleanup
when building with W=1:
drivers/net/wireless/ath/ath10k/pci.c:1696:21: warning: variable
'ar_pci' set but not used [-Wunused-but-set-variable]
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
caldata is not being free'd on the error exit path, causing
a memory leak and data definitely should not be freed. Free
caldata instead of data.
Thanks to Kalle Valo for spotting that data should not be
free'd.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 3c97f5de1f ("ath10k: implement NAPI support") conflicts with
ath-current. To avoid any merge problems merge ath-current to ath-next already now.
Conflicts:
drivers/net/wireless/ath/ath10k/htt_rx.c
carl9170_usb_stop() is used from several places to flush and cleanup any
pending work. The normal pattern is to send a request and wait for the
irq handler to call complete(). The completion is not reinitialized
during normal operation and as the old comment indicates it is important
to keep calls to wait_for_completion_timeout() and complete() balanced.
Calling complete_all() brings this equilibirum out of balance and needs
to be fixed by a reinit_completion(). But that opens a small race
window. It is possible that the sequence of complete_all(),
reinit_completion() is faster than the wait_for_completion_timeout() can
do its work. The wake up is not lost but the done counter test is after
reinit_completion() has been executed. The only reason we don't see
carl9170_exec_cmd() hang forever is we use the timeout version of
wait_for_copletion().
Let's fix this by reinitializing the completion (that is just setting
done counter to 0) just before we send out an request. Now,
carl9170_usb_stop() can be sure a complete() call is enough to make
progess since there is only one waiter at max. This is a common pattern
also seen in various drivers which use completion.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl driver attempts to get the txpower value from the radio by first
clearing the existing stored value and then watching the value to become
non-zero.
APs allow setting client power to values from -127..127, but this radio
is not capable of setting values less then 0 and so will report txpower
as 0dbm for both negative and 0 client power values.
When the radio has txpower set to 0dbm txpower (equivalent to 1mw) the
ath6kl_cfg80211_get_txpower() function will remain in the
wait_event_interruptible_timeout() loop waiting for the value to be
non-zero, and will eventually timeout. This results in a 5 second delay in
response. However, the correct value of zero is eventually returned.
The 6004 defaults to 63dbm which is then limited by regulatory and
hardware limits with max of 18dbm (6003 max is 16dbm), therefore we can
use values larger then these to be able to determine when the value has
been updated.
To correct the issue, set the value to a nonsensical value (255) and wait
for it to change to the valid value.
Tested on both 6003 and 6004 based radios. Return value of zero is
correctly returned in an expected amount of time (similar to when
returning non-zero values) when AP client power is set to both 0 and
negative values.
Signed-off-by: Eric Bentley <eric.bentley@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The firmware crash dumps on the 6004 are the same as the 6003. Remove the
statement guarding it from dumping on the 6004. Renamed the
REG_DUMP_COUNT_AR6003 to reflect support on both chips.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The constant "123", which is the number of elements in
mask_m / mask_p, is repeated several times in this function.
Replace memsets with array initialization, and replace a loop
conditional with ARRAY_SIZE() so that we don't repeat ourselves.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When user requests for survey dump data, driver is providing wrong survey
information. This information we sent is the survey data that we have
collected during previous user request.
This issue occurs because we request survey dump for wrong channel. With
this change, we correctly display the correct and current survey
information to userspace.
Fixes: fa7937e3d5 ("ath10k: update bss channel survey information")
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error assigned does not seems to be used anywhere,
fixes nothing just a small cleanup
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For non-aggregated frames, ath9k was leaving handling of powersave
filtered packets to mac80211. This can be too slow if the intermediate
queue is already filled with packets and mac80211 does not immediately
send a new packet via drv_tx().
Improve response time with filtered frames by triggering clearing the
powersave filter internally.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It removes the need for undoing the padding changes to skb->data and it
improves performance by eliminating one tx status lookup per MPDU in the
status path. It is also useful for preparing a follow-up fix to better
handle powersave filtering.
A side effect is that these counters, available via debugfs, become now invalid:
* dot11TransmittedFragmentCount
* dot11FrameDuplicateCount,
* dot11ReceivedFragmentCount
* dot11MulticastReceivedFrameCount
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@qca.qualcomm.com: add a note about counters, thanks to Zefir Kurtisi]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 7a0adc83f3 ("ath10k: improve tx scheduling") is causing
severe throughput drop in multi client mode. This issue is originally
reported in veriwave setup with 50 clients with TCP downlink traffic.
While increasing number of clients, the average throughput drops
gradually. With 50 clients, the combined peak throughput is decreased
to 98 Mbps whereas reverting given commit restored it to 550 Mbps.
Processing txqs for every tx completion is causing overhead. Ideally for
management frame tx completion, pending txqs processing can be avoided.
The change partly reverts the commit "ath10k: improve tx scheduling".
Processing pending txqs after all skbs tx completion will yeild enough
room to burst tx frames.
Fixes: 7a0adc83f3 ("ath10k: improve tx scheduling")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add NAPI support for rx and tx completion. NAPI poll is scheduled
from interrupt handler. The design is as below
- on interrupt
- schedule napi and mask interrupts
- on poll
- process all pipes (no actual Tx/Rx)
- process Rx within budget
- if quota exceeds budget reschedule napi poll by returning budget
- process Tx completions and update budget if necessary
- process Tx fetch indications (pull-push)
- push any other pending Tx (if possible)
- before resched or napi completion replenish htt rx ring buffer
- if work done < budget, complete napi poll and unmask interrupts
This change also get rid of two tasklets (intr_tq and txrx_compl_task).
Measured peak throughput with NAPI on IPQ4019 platform in controlled
environment. No noticeable reduction in throughput is seen and also
observed improvements in CPU usage. Approx. 15% CPU usage got reduced
in UDP uplink case.
DL: AP DUT Tx
UL: AP DUT Rx
IPQ4019 (avg. cpu usage %)
========
TOT +NAPI
=========== =============
TCP DL 644 Mbps (42%) 645 Mbps (36%)
TCP UL 673 Mbps (30%) 675 Mbps (26%)
UDP DL 682 Mbps (49%) 680 Mbps (49%)
UDP UL 720 Mbps (28%) 717 Mbps (11%)
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A regression was introduced in commit id 79d4db1214 ("ath9k: cleanup
led_pin initial") that broken the WLAN status led on my laptop with
AR9287 after suspending and resuming.
Steps to reproduce:
* Suspend (laptop)
* Resume (laptop)
* Observe that the WLAN led no longer turns ON/OFF depending on the
status and is always red
Even though for my case it only needs to be set to OUT in ath9k_start
but for consistency bring back the IN direction setting as well.
Fixes: 79d4db1214 ("ath9k: cleanup led_pin initial")
Cc: Miaoqing Pan <miaoqing@codeaurora.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: <stable@vger.kernel.org> # 4.7+
Link: https://bugzilla.kernel.org/show_bug.cgi?id=151711
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
EEPROM size calculated in 16-bit words, so we should take into account
this fact during buffer allocation.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We get 1 warning about global functions without a declaration
in the ath9k gpio driver when building with W=1:
drivers/net/wireless/ath/ath9k/gpio.c:25:6: warning: no previous prototype for 'ath_fill_led_pin' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static.
so this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trivial fix to spelling mistake in ath10k_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Older firmware with HTT delivers incorrect tx status for null func
frames to driver, but this fixed in 10.2 and 10.4 firmware versions.
Also this workaround results in reporting of incorrect null func status
for 10.4. Fix this is by introducing a firmware feature flag for 10.4
so that this workaround is skipped and proper tx status for null func
frames are reported
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 97f2645f35 ("tree-wide: replace config_enabled() with
IS_ENABLED()") mostly did away with config_enabled().
This is one of the postponed TODO items as config_enabled() is used
for a tristate option here. Theoretically, config_enabled() is
equivalent to IS_BUILTIN(), but I guess IS_REACHABLE() is the best
fit for this case because both CONFIG_HWMON and CONFIG_ATH10K are
tristate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For 10.4 fw versions, dbglog module id has been extended from u32
to u64, hence this patch fixes the same in the ath10k driver side.
This patch doesn't break the older 10.4 releases. The FW change
is already present in the older FWs.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
waiter context waker context
scan.started
------------
ath10k_start_scan()
lockdep_assert_held(conf_mutex)
auth10k_wmi_start_scan()
wait_for_completion_timeout(scan.started)
ath10k_wmi_event_scan_start_failed()
complete(scan.started)
ath10k_wmi_event_scan_started()
complete(scan.started)
scan.completed
--------------
ath10k_scan_stop()
lockdep_assert_held(conf_mutex)
ath10k_wmi_stop_scan()
wait_for_completion_timeout(scan.completed)
__ath10k_scan_finish()
complete(scan.completed)
scan.on_channel
---------------
ath10k_remain_on_channel()
mutex_lock(conf_mutex)
ath10k_start_scan()
wait_for_completion_timeout(scan.on_channel)
ath10k_wmi_event_scan_foreign_chan()
complete(scan.on_channel)
offchan_tx_completed
--------------------
ath10k_offchan_tx_work()
mutex_lock(conf_mutex)
reinit_completion(offchan_tx_completed)
wait_for_completion_timeout(offchan_tx_completed)
ath10k_report_offchain_tx()
complete(offchan_tx_completed)
install_key_done
----------------
ath10k_install_key()
lockep_assert_held(conf_mutex)
reinit_completion(install_key_done)
wait_for_completion_timeout(install_key_done)
ath10k_htt_t2h_msg_handler()
complete(install_key_done)
vdev_setup_done
---------------
ath10k_monitor_vdev_start()
lockdep_assert_held(conf_mutex)
reinit_completion(vdev_setup_done)
ath10k_vdev_setup_sync()
wait_for_completion_timeout(vdev_setup_done)
ath10k_wmi_event_vdev_start_resp()
complete(vdev_setup_done)
ath10k_monitor_vdev_stop()
lockdep_assert_held(conf_mutex)
reinit_completion(vdev_setup_done()
ath10k_vdev_setup_sync()
wait_for_completion_timeout(vdev_setup_done)
ath10k_wmi_event_vdev_stopped()
complete(vdev_setup_done)
thermal.wmi_sync
----------------
ath10k_thermal_show_temp()
mutex_lock(conf_mutex)
reinit_completion(thermal.wmi_sync)
wait_for_completion_timeout(thermal.wmi_sync)
ath10k_thermal_event_temperature()
complete(thermal.wmi_sync)
bss_survey_done
---------------
ath10k_mac_update_bss_chan_survey
lockdep_assert_held(conf_mutex)
reinit_completion(bss_survey_done)
wait_for_completion_timeout(bss_survey_done)
ath10k_wmi_event_pdev_bss_chan_info()
complete(bss_survey_done)
All complete() calls happen while the conf_mutex is taken. That means
at max one waiter is possible.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the wake tx queue path, we are not checking if the frame to be sent
takes management path or not. For eg. QOS null func frame coming here will
take the management path. Since we are not incrementing the descriptor
counter (num_pending_mgmt_tx) w.r.t tx management, on tx completion it is
possible to see negative values.
When the above counter reaches a negative value, we will not be sending a
probe response out.
if (is_presp &&
ar->hw_params.max_probe_resp_desc_thres < htt->num_pending_mgmt_tx)
For IPQ4019, max_probe_resp_desc_thres (u32) is 24 is compared against
num_pending_mgmt_tx (int) and the above condtions comes true if the counter
is negative and we drop the probe response.
To avoid this, check on the wake tx queue path as well for the tx path of
the frame and increment the appropriate counters
Fixes: cac085524c "ath10k: move mgmt descriptor limit handle under mgmt_tx"
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
txqs_lock is interfering with wake_tx_queue submitting more frames.
so queues don't get filled in and don't keep firmware/hardware busy
enough. This change helps to reduce the txqs_lock contention and
wake_tx_queue() blockage to being possible in txrx_unref().
To reduce turn around time of wake_tx_queue ops and to maintain fairness
among all txqs, the callback is updated to push first txq alone from
pending list for every wake_tx_queue call. Remaining txqs will be
processed later upon tx completion.
Below improvements are observed in push-only mode and validated on
IPQ4019 platform. With this change, in AP mode ~10Mbps increase is
observed in downlink (AP -> STA) traffic and approx. 5-10% of CPU
usage is reduced.
Major improvement is observed in 1-hop Mesh mode topology in 11ACVHT80.
Compared to Infra mode, CPU overhead is higher in Mesh mode due to path
lookup and no fast-xmit support. So reducing spin lock contention is
helping in Mesh.
TOT +change
-------- --------
TCP DL 545 Mbps 595 Mbps
TCP UL 555 Mbps 585 Mbps
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'WMI_10_4_WDS_PEER_EVENTID' is not yet handled/implemented for WDS mode,
as of now suppress the warning message "Unknown eventid: 36903"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent commit 46f6b06050 ("mac80211: Encrypt "Group addressed privacy" action
frames") encrypts group privacy action frames. But qca99x0 family chipset
delivers broadcast/multicast management frames as encrypted and it should be
decrypted by mac80211. Setting RX_FLAG_DECRYPTED stats for those frames is
breaking mesh connection establishment.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With the %pK format specifier we hide the kernel addresses
with the help of kptr_restrict sysctl.
In this patch, %p is changed to %pK in the driver code.
The sysctl is documented in Documentation/sysctl/kernel.txt.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT service has missed in
the commit 7e247a9e88 ("ath10k: add dynamic tx mode switch
config support for qca4019"). This patch adds the service to
avoid mismatch between host and target.
Fixes: 7e247a9e88 ("ath10k: add dynamic tx mode switch config support for qca4019")
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the FW version is taken from the sw_version field
of the FW ready event. This version is based on internal
version control revision and it is difficult to map to actual
FW version.
Fix this by using the actual FW version stored in the FW file
header record.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When driver is loaded, extract a capabilities record
from the FW file. This record contains bits indicating
which optional features are supported by this FW.
The driver can use this information to determine
which functionality to support and/or expose to user
space.
The extraction is done before wiphy structure is
registered, because the capabilities can affect
information published by the this structure.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the places that check wil->scan_request and
call cfg80211_scan_done are not consistently protected,
so there is a risk that cfg80211_scan_done will be called
with NULL scan_request, causing a kernel crash.
Fix this by using p2p_wdev_mutex in few other places
that access scan_request. This makes sense since
scan_request may point to p2p_wdev, and it is not worth
the extra complexity of adding a new mutex.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW Rx filters and masks are not configured
properly by firmware during boot sequences. The
MAC_PCU_ADDR1 is set to 0s instead of 1s which
allows the HW to ACK any frame that passes through
MAC_PCU_RX_FILTER. The MAC_PCU_RX_FILTER itself
is misconfigured on boot as well.
The combination of these bugs ended up with the
following manifestations:
- "no channel configured; ignoring frame(s)!"
warnings in the driver
- spurious ACKs (transmission) on the air during
firmware bootup sequences
The former was a long standing and known bug
originally though mostly harmless.
However Marek recently discovered that this
problem also involves ACKing *all* frames the HW
receives (including beacons ;). Such frames
are delivered to host and generate the former
warning as well.
This could be a problem with regulatory compliance
in some rare cases (e.g. Taiwan which forbids
transmissions on channel 36 which is the default
bootup channel on 5Ghz band cards). The good news
is that it'd require someone else to violate
regulatory first to coerce our device to generate
and transmit an ACK.
The problem could be reproduced in a rather busy
environment that has a lot of APs. The likelihood
could be increased by injecting an msleep() of
5000 or longer immediately after
ath10k_htt_setup() in ath10k_core_start().
The reason why the former warnings were only
showing up seldom is because the device was either
quickly reset again (i.e. during firmware probing)
or wmi vdev was created (which fixes hw and fw
states).
It is technically possible for host driver to
override adequate hw registers however this can't
work reliably because the bug root cause lies in
incorrect firmware state on boot (internal
structure used to program MAC_PCU_ADDR1 is not
properly initialized) and only vdev create/delete
events can fix it. This is why the patch takes
dummy vdev approach.
This could be fixed in firmware as well but having
this fixed in driver is more robust, most notably
when thinking of users of older firmware such as
999.999.0.636.
Reported-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows placing command barriers for explicit
serializing and synchronizing state.
Useful for future driver development.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds testmode support for 10.4 based chipsets
and added code swap support for UTF binary.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently testmode events for 10.x firmware are processed from
10.1 wmi event processing. This patch is used to handle testmode
events in 10.2 and 10.4 based firmware.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Preparation to make use of firmware_swap_code_seg_info for UTF binary.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Support for QCA9887 is no longer experimental and if there are any issues
we need to address them
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A station pointer can be passed to the driver on tx, before it has been
marked as associated. Since ath9k_sta_state was initializing the entry
too late, it resulted in some spurious crashes.
Fixes: df3c6eb34d ("ath9k: Use sta_state() callback")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently wiphy structure is initialized and registered
in wil_if_alloc, before some information is available such
as MAC address and capabilities. As a result there is a
small chance user space will get incorrect information
from calls such as NL80211_CMD_GET_WIPHY.
Fix this by seperating the registration and moving it
to wil_if_add which is executed later, after all
relevant information is known.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
txdata->enabled is used in order to determine if the TX vring
is valid. As the data transmit is handled in a different context,
in case txdata->enabled is set before vring->hwtail is updated,
an old or corrupted vring->hwtail can be used.
Protect setting of txdata->enabled and vring->hwtail to prevent a
case where TX vring start handling TX packets before setting
vring->hwtail.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Stations disconnection is executed as part of wil_reset so no
need to do it in wil_down.
Removal of the disconnect operation will also preserve the lock
of wil->mutex during the whole reset flow and prevent handling of
connect event while resetting.
Set wil_status_resetting in earlier stage in the flow to prevent
double resetting call in case communication with FW fails while
bringing the interface down.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
fix stop p2p device handling to identify between search
and listen and update the upper layers with the appropriate
notification.
The stop of p2p radio operations also needs to be performed
in __wil_down.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Change the logging category of HALP functions from
MISC to IRQ, since the HALP mechanism is closely
related to interrupts. Both HALP and IRQ create
a heavy load of logging messages when enabled,
so their logging is typically disabled during normal debug
scenarios. Having them in the same logging category
will make it easier to disable logging for both in one go.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to the spec the PN should be calculated per TID.
In the current implementation, the PN and key_set were set
only for TID 0, therefore only traffic for TID 0 was supported.
In order to support all TIDs, the key_set and PN should be set
for all the TIDs.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case HALP vote times out, we need to mask the HALP IRQ, as done
in case the interrupt is received, as this interrupt should be
set until completion of the low latency operation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
just to comply with current ath9k_hw_nvram_read to return value, hence
behaving reacting accordingly.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes smatch warning:
ath9k_vif_iter_set_beacon() warn if statement not indented
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce indentation, use a variable to save a few pointer dereferences
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR_PHY_65NM_CH0_THERM and AR_CH0_THERM were supposed to refer to the
same register, however they had different SREV checks.
Remove the duplicate and use the checks. Since there were other SREV
checks present in the only place that uses this, this will probaby not
affect runtime behavior.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The register layout of AR_PHY_SPECTRAL_SCAN has changed, only AR9280
uses the old layout
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There were two paths in the code for "external" eeprom sources. The code
in eeprom.c only handled the cases where the eeprom data was loaded via
request_firmware. ahb.c and pci.c on the other hand had some duplicate
code which was only used when the eeprom data was passed via
ath9k_platform_data.
With this change all eeprom data handling is now unified in eeprom.c.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When an NL80211_DISCONNECT is sent to cfg80211, the driver's cfg80211
disconnect function sets the sme_state to SME_DISCONNECTED before receiving
a WMI_DISCONNECT_EVENT from the firmware. This caused cfg80211 to not know
that the connection is disconnected because the driver fails to notify
cfg80211 upon receiving WMI_DISCONNECT_EVENT from the firmware believing
it is already disconnected.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When disabling tethering after having enabled it, the ath6kl driver does
not set the IFF_LOWER_UP flag to 0 (carrier off) on the wlan interface.
The upper layers (eg. connman) are not notified of the tethering mode
status change. So, tethering can not be activated anymore.
This patch adds a netif_carrier_off() call when stopping AP mode to fix
the problem.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One minute after a successful connection, the kernel checks if the
frequency and the channel width are well configured for the country we
are in. (regulatory domain)
ath6kl driver was setting the NL80211_CHAN_HT20 channel without checking
for the HT capabilities. (we should have NL80211_CHAN_NO_HT in our
case because the firmware did not support HT)
This patch adds a check on ht_cap.ht_supported in order to create the
channel corresponding to the firmware capabilities.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When enabling WLAN tethering, a new AP is visible and a STA could
connect to it. When the STA tries to authenticate to the newly created
AP, the WPA authentication mechanism is stuck in the 1/4 msg of 4-Way
Handshake.
In ath6kl_rx(), the ath6kl_find_sta() function is looking for the
h_source field of the Ethernet frame header received by the STA. The
datap pointer that points to the Ethernet frame header is incorrect,
and was pointing at the wrong offset in the buffer.
This commit adds a pad_before_data_start offset to set the datap pointer
to the Ethernet frame header. datap->h_source parameter is now really
pointing to the source ethernet address and the authentication process
can continue.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ideally wake_tx_queue should be used regardless as
it is a requirement for reducing bufferbloat and
implementing airtime fairness in the future.
However some setups (typically low-end platforms
hosting QCA988X) suffer performance regressions
with the current wake_tx_queue implementation.
Therefore disable it unless it is really
beneficial with current codebase (which is when
firmware supports smart pull-push tx scheduling).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As hw cycle counters in QCA4019 wraparound independantly in QCA4019
it is possible cycle counter and rx clear counter would wraparound
at the same time. Current logic assumes only one of the counters
would wraparound at anytime. Fix this by moving 'else' part to
another 'if'.
Fixes: 8e100354a9 ("ath10k: fix cycle counter wraparound handling for QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes the firmware sends a HAL_DEL_BA_IND, the prima driver silently
ignore this message so let's do the same to silence the error message.
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch fixes some issues with interface reconfiguration. It could
for example happen that an AP interface in beacon slot 0 was removed
leaving an IBSS station in one of the other slots. When this happens
the driver never sends out the beacon as it only tries to send a beacon
from slot 0.
Appart from that the tracking of required changes to the beacon config is
relatively complicated and prone to errors.
The approach taken here is to solve reconfiguration issues is to
reconfigure the beacons when any interface changes. This means that
the complexity of deciding whether an interface change may modify the
beacon configuration is gone. It also means that the beacon config will
be reliably updated when an interface is removed.
The issue that a single non-AP interface might not be in beacon
slot 0 and wouldn't be send out is solved by moving it into the
first slot. The TSF value in hardware is adjusted accordingly so
that the timestamp of the beacons stay consistent.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The removed ATH9K_SLOT_TIME_X constants simply map the value in microseconds
to the same integer. These constants were not used consistently, so fix the
inconsistency issue by replacing all occurances with the integer equivalent.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k driver modifies the TSF for VIFs for the purpose of sending
beacons in a staggered fashion. This patch exposes this VIF specific
adjustment of the TSF value to mac80211. Without the change the TSF
routines handle the hardware TSF value instead of the actual TSF value as
seen on the air.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These changes make ath9k_hw_reset more consistent with other places that
handle the TSF value by using the same helper routine.
A slight improvement is to not assume that a fixed time of 1.5ms has
passed for the initval writes when compared to the first write attempt.
Instead the TSF value is re-calculated which will yield a higher accuracy
of the restored TSF timer.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k TSF handling routines need to be aware of the channel context that
is being modified. With this change the TSF related values that are stored
in each channel context will be correctly tracked and the harware will only
be updated if the modified context is currently the active one.
Without this change the TSF modifications done using these routines would
for example be lost during a hardware reset as done by ath_complete_reset.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Beacons were not send out at (timestamp % beacon_time == 0) for interfaces
other than the primary one. To send out beacons with the correct timestamp
according to 10.1.3.2 of the 802.11 standard the tsf_adjustment has to be
set to the negative time difference instead of positive. This way the
later beacons get corrected to have a lower (and similar) timestamp with
regard to the beacon from slot 0.
I am not aware about any issues that have been caused by this.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes, this simply makes the code easier to understand
because all initialization based on ath9k_platform_data is now within
one function.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath9k_hw_init_macaddr unconditionally returns 0 in all cases, making the
return value unnecessary.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently setting the MAC address via ath9k_platform_data works only due
to the order in which init.c sets common->macaddr, which is done after
ath9k_hw_init_macaddr was executed. It would be better if the latter
was independent of the order in which it's being called.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes - this only removes a variable which is set but
never read.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some devices running OpenWrt need this and it makes sense to add this
to ath9k_platform_data as the next patches will add a devicetree
(boolean) property for it as well.
Suggested-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix up the wcn36xx_smd_update_scan_params() to work with non-ancient
versions of the firmware and support actually specifying the list of
channels.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The CCU block in WCNSS is configured for appropriate routing of
interrupts from the DXE to the application cpu, this is not dependant on
the iris version (wcn3660 vs wcn3680), but rather if the SoC has a riva
or pronto built in.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split the wcnss mmio space into explicit regions for ccu and dxe and
acquire these from the node referenced by the qcom,mmio phandle.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for handling incoming messages from IRQ context, change
the indication list lock to a spinlock
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Merge the two allocation instead of separately allocating room for the
indication payload.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Print an ath10k error message rather a call trace when HTT op version is
not found from firmware META data (IE). This should be sufficient to figure
out what went wrong.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9888 shares the same configuration with QCA99X0
with NSS=2.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rtc_state_cold_reset_mask is unused in ath10k_hw_regs.
instead fixed delays are used.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If WMI and/or firmware has issues removing the peer object,
then we still need to clean up the peer object in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not sure this can happen, but seems like a reasonable sanity
check.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
just to comply to coding style.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is expected that all pktlog events for 10.4 firmware based solutions
should come through CE8 where as in case of 10.2 firmware based solutions,
it should come through one of the HTT events (HTT_T2H_MSG_TYPE_PKTLOG).
But from experiments with 10.4 based solutions, it is observed that pktlog
event for ATH_PKTLOG_TYPE_TX_MSDU_ID is coming through HTT pktlog event.
Currently, we always parse with 10.2 pktlog header which will lead to
pktlog decoding issues (payload length mismatch exceptions)
For trace points, it is required to provide only the payload size. So
fixing this by simplifying the payload size calculation without the use of
ath10k pktlog headers.
While there, remove the unused ath10k pktlog headers.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
<linux/semaphore.h> is not used anymore, so just remove the include.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While debugging OS crashes due to firmware crashes, I enabled
kasan, and it noticed that peer objects were being used-after-freed.
Looks like there are two places we could be leaving stale references
in the peer-map, so clean that up.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Otherwise, the txrx-compl-task may access some bad memory?
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211/nl80211 interface changes for per STA total rx-duration and
very basic 'ath10k_sta_statistics' mac80211 callback is implemented
to extend support for per station statistics from the driver.
Also provision in 'iw dev wlan#N station dump' to parse rx-duration
is supported. So its safer to remove the debugfs entry for per STA
rx-duration
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable support for 'drv_sta_statistics' callback.
Export rx_duration support if available to cfg80211/nl80211
This can also act as a placeholder for any new per STA stats support
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 'extended peer stats' will be not be appended with normal peer stats
data and they shall be coming in separate chunks. Fix this by maintaining
a separate linked list 'extender peer stats' for 10.4 and update
rx_duration for per station statistics. Also parse through beacon filter
(if enabled), to make sure we parse the extended peer stats properly.
This issue was exposed when more than one client is connected and
extended peer stats for 10.4 is enabled
The order for the stats is as below
S - standard peer stats, E- extended peer stats, B - beacon filter stats
{S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..}
Fixes: f9575793d4 ("ath10k: enable parsing per station rx duration for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function ar9003_hw_apply_minccapwr_thresh takes as second parameter not
a pointer to the channel but a boolean value describing whether the channel
is 2.4GHz or not. This broke (according to the origin commit) the ETSI
regulatory compliance on 5GHz channels.
Fixes: 3533bf6b15 ("ath9k: Fix regulatory compliance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just setting the proper return for reading beyond the eeprom data.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found this obvious typo while going through the spectral
code design in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Disable TX_STBC for both HT and VHT if the devices tx chainmask is '1'
TX_STBC is required only for devices with tx_chainmask > 1. This fixes
a ping failure for QCA9887 (1x1) in HT/VHT mode
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable beacon loss detection support for 10.4 by handling
roam event. With this change QCA99X0 station is able to
detect beacon loss when the AP is powered off
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch warns about a number of cases in ath10k where a pointer is
null-checked after it has already been dereferenced, in code involving
ath10k private virtual interface pointers.
Fix these by making the dereference happen later.
Addresses the following smatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:3651 ath10k_mac_txq_init() warn: variable dereferenced before check 'txq' (see line 3649)
drivers/net/wireless/ath/ath10k/mac.c:3664 ath10k_mac_txq_unref() warn: variable dereferenced before check 'txq' (see line 3659)
drivers/net/wireless/ath/ath10k/htt_tx.c:70 __ath10k_htt_tx_txq_recalc() warn: variable dereferenced before check 'txq->sta' (see line 52)
drivers/net/wireless/ath/ath10k/htt_tx.c:740 ath10k_htt_tx_get_vdev_id() warn: variable dereferenced before check 'cb->vif' (see line 736)
drivers/net/wireless/ath/ath10k/txrx.c:86 ath10k_txrx_tx_unref() warn: variable dereferenced before check 'txq' (see line 84)
drivers/net/wireless/ath/ath10k/wmi.c:1837 ath10k_wmi_op_gen_mgmt_tx() warn: variable dereferenced before check 'cb->vif' (see line 1825)
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The below warning message seems to hit occasionally with the following
combination (IPQ4019 + ACS scan) where we receive packets as a self peer
when hostapd does ACS when we bring up AP mode . ath10k has the below
fall back mechanism to fetch current operating channel in rx (it will
check for the next channel tracking variable if the current one is NULL)
[scan channel] --> [rx channel] --> [peer channel] -->
[vdev channel] --> [any vdev channel] --> [target oper channel]
'scan channel' and 'target operating channel' are directly fetched from
firmware events. All the others should be updated by mac80211.
During ACS scan we wouldn't have a valid channel context
assigned from mac80211 ('ar->rx_channel'), and also relying on
('ar->scan_channel') is not helpful (it becomes NULL when it goes to
BSS channel and also when the scan event is completed). In short we
cannot always rely on these two channel tracking variables.
'Target Operating Channel' (ar->tgt_oper_chan) seems to keep track of
the current operating even while we are doing ACS scan and etc. Hence
remove this un-necessary warning message and continue with
target_operating channel. At the worst case scenario when the target
operating channel is invalid (NULL) we already have an ath10k warning
message to notify we really don't have a proper channel configured in
rx to update the rx status("no channel configured; ignoring frame(s)!")
WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
[<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
(ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
[<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
[<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
[<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])
Fixes:3b0499e9ce42 ("ath10k: reduce warning messages during rx without proper channel context")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Usually when the firmware crashes we check for the value
'FW_IND_EVENT_PENDING' in 'FW_INDICATOR_ADDRESS' and proceed with
disabling the irq and dumping firmware 'crash dump'. Now
when the PCI card is unplugged from the device the PCI controller
seems to generate a spurious interrupt after some time which
was as treated a firmware crash and resulting in the below race
condition (and eventually crashing the system)
ath10k_core_unregister -> ath10k_core_free_board_files
...... device unplug spurious interrupt .........
ath10k_pci_taklet -> ath10k_pci_fw_crashed_dump ...etc
Clearly even after the firmware board files related data structure
is freed up we are getting a spurious interrupt from PCI with 0xfffffff
in the 'FW_INDICATOR_ADDRESS' resulting in scheduling of the pci tasklet
and doing a crash dump, printing f/w board related info resulting in the
below crash. Fix this by detecting this spurious interrupt in ath10k PCI
irq handler itself and return IRQ_NONE. Thanks to Michal Kazior for
helping us conclude the most appropriate fix.
Call trace:
EIP is at ath10k_debug_print_board_info+0x39/0xb0
[ath10k_core]
EAX: 00000000 EBX: d4de15a0 ECX: 00000000 EDX: 00000064
ESI: f615ddd0 EDI: f8530000 EBP: f615de3c ESP: f615ddbc
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 01c0a000 CR4: 000006f0
Stack:
f615ddd0 00000064 f8b4ecdd 00000000 00000000 00412f4e
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
Call Trace:
[<f8b1f517>] ath10k_print_driver_info+0x17/0x30
[ath10k_core]
[<f875463a>] ath10k_pci_fw_crashed_dump+0x7a/0xe0
[ath10k_pci]
[<f87549d0>] ath10k_pci_tasklet+0x70/0x90 [ath10k_pci]
[<c106151e>] tasklet_action+0x9e/0xb0
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.8. Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
The nl80211 layer expects P2P search operation to be aborted
if needed when stopping P2P device. If the P2P search operation
is still running after returning from stop_p2p_device
it causes a WARN_ON and possibly a kernel crash.
Fix this by aborting the P2P search in wil_cfg80211_stop_p2p_device
and preventing P2P search from being started on a stopped P2P
device.
Note, the fix does not cover the case where a regular scan
is started on the P2P device. It will be completed in the
future when support is added for aborting a scan operation.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In wil_p2p_listen chan is checked to protect against NULL
pointer access only before setting channel = chan->hw_value.
Add a global parameter check to cover all accesses to chan.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In this switch statement, the default case does not always assign
sifs. In practice, ah->ah_bwmode cannot take values besides the
other labels, so this is not an actual problem, but it looks odd
and smatch complains thus:
ath5k_hw_get_default_sifs() warn: missing break? reassigning 'sifs'
Silence the warning by moving default label up a line.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 5c86d97bcc ("ath10k: combine txrx and replenish task")
introduced deadlock while processing rx in order indication message
for qca6174 based devices. While merging replenish and txrx tasklets,
replenish task should be called out of htt rx ring locking since it
is also try to acquire the same lock.
Unfortunately this issue is not exposed by other solutions (qca988x,
qca99x0 & qca4019), as rx_in_ord_ind message is specific to qca6174
based devices. This patch fixes
=============================================
[ INFO: possible recursive locking detected ]
4.7.0-rc2-wt-ath+ #1353 Tainted: G E
---------------------------------------------
swapper/3/0 is trying to acquire lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d7ef19>]
ath10k_htt_rx_msdu_buff_replenish+0x29/0x90 [ath10k_core]
but task is already holding lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&htt->rx_ring.lock)->rlock);
lock(&(&htt->rx_ring.lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by swapper/3/0:
#0: (&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=119151
Fixes: 5c86d97bcc ("ath10k: combine txrx and replenish task")
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In QCA4019, cycle counter wraparound is not tied to rx
clear counter. Each counter would wraparound individually
and after wraparound the respective counter will be reset
to 0x7fffffff while other counter still running unaffected.
Define a new wraparound type for this behaviour and handle
it separately so that rx clear counter wraparound is also
handled just like cycle counter. With this type of
wraparound we can accurately compute and report channel
active/busy time when any of the counter overflows.
Fixes: ee9ca147c5 ("ath10k: Fix survey reporting with QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X hw implements a different cycle counter wraparound
behaviour when compared to QCA4019. To properly handle different
wraparound logic for these chipsets replace already available
bool hw_params member, has_shifted_cc_wraparound, with an
enum which could be extended to handle different wraparound
behaviour. This patch keeps the existing logic functionally
same and a prepares cycle counter wraparound handling to
extend for other chips.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: change also QCA9887 wrap type]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CCK hardware table mapping from QCA99X0 onwards got revised.
The CCK hardware rate values are in a proper order wrt. to
rate and preamble as below
ATH10K_HW_RATE_REV2_CCK_LP_1M = 1,
ATH10K_HW_RATE_REV2_CCK_LP_2M = 2,
ATH10K_HW_RATE_REV2_CCK_LP_5_5M = 3,
ATH10K_HW_RATE_REV2_CCK_LP_11M = 4,
ATH10K_HW_RATE_REV2_CCK_SP_2M = 5,
ATH10K_HW_RATE_REV2_CCK_SP_5_5M = 6,
ATH10K_HW_RATE_REV2_CCK_SP_11M = 7,
This results in reporting of rx frames (with CCK rates)
totally wrong for QCA99X0, QCA4019. Fix this by having
separate CCK rate table for these chipsets with rev2 suffix
and registering the correct rate mapping to mac80211 based on
the new hw_param (introduced) 'cck_rate_map_rev2' which shall
be true for any newchipsets from QCA99X0 onwards
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All these flags are not used and their use is completely
covered by 'ath10k_hw_rate_ofdm', 'ath10k_hw_rate_cck',
and RX_PPDU_START_RATE_FLAG
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only five bits are defined to pass tid information in HTT_RX_IND
message, so the mask which can be used to extract tid should be 0x1f
instead of the current 0x3f. Also, macros which can be used to extract
flush_valid and release_valid bits have to be left shifted one bit less
because these information follow the tid right after. This patch does
not really fix anything functionally because these macros are not used
currently.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This looks like a regression from commit c4cdf753ed ("ath10k: move
fw_features to struct ath10k_fw_file"), we were printing the features from a
wrong struct.
Fixes: c4cdf753ed ("ath10k: move fw_features to struct ath10k_fw_file")
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA9887 stores its calibration data (board.bin) inside the EEPROM of
the target. This has to be downloaded manually to allow the device to
initialize correctly.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
[kvalo@qca.qualcomm.com: handle -EOPNOTSUPP and s/fetch_board_data/fetch_cal_eeprom]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the hardware name, revision, firmware names and update the pci_id
table.
QA9887 HW1.0 is supposed to be similar to QCA988X HW2.0 . Details about
he firmware interface are currently unknown.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
[kvalo@qca.qualcomm.com: add a warning about experimental support]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The previous text was confusing, leading readers to think this
driver was a duplicate, and so didn't need to be enabled.
After the removal of the older staging driver, this is the only
driver in mainline for these devices.
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the necessary patches to make wifi running (over AHB)
on ipq4019 SoC are ready now. It's good to enable
ipq4019 wifi device probing in ahb module and
remove work in progress debug print.
Device tree change is there in the public review by
below commit message
"qcom: ipq4019: add wifi nodes to ipq4019 SoC device tree"
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware has support to enable or disable btcoex functionality
without reloading firmware via wmi pdev param. Add provision to send
pdev param command via existing btcoex knob.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This feature flag will be used for firmware to support BT-Coex feature
without reloading firmware via WMI pdev param. To support Bluetooth
coexistence pdev param, WMI_COEX_GPIO_SUPPORT of extended resource
config should be enabled always. This firmware IE is used to configure
WMI_COEX_GPIO_SUPPORT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update module description to advertise all supported QCA 802.11ac devices.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove unused inline function phy_mode_to_band.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Earlier when operating irq mode is legacy, interrupts are disabled
and re-enabled based on num_msi_intrs. commit cfe9011a05 ("ath10k:
remove MSI range support") replaced num_msi_intrs by oper_irq_mode.
Since oper_irq_mode is not initialized for ahb devices (i.e qca4019),
device boot up is failed during probe.
Fixes: cfe9011a05 ("ath10k: remove MSI range support")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix invalid argument error while writing 'simulate_fw_crash',
though the funcionality is working fine we get an error 'invalid
argument' because 'count' value is not returned properly
(no reason to reduce the count value for removing the newline)
Fixes the below write error:
/sys/kernel/debug/ieee80211/phy0/ath10k# echo hw-restart >
simulate_fw_crash
-bash: echo: write error: Invalid argument
Also move the 'conf_mutex' as it is really not required for
fetching the userspace buffer.
Reported-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
diag_read uses dma_alloc_coherent to allocate memory requested by the
caller. If this memory requested is larger, more than DIAG_TRANSFER_LIMIT
(2K), then it is likely that we may not get the requested memory and we
would fail.
To solve this, request dma_alloc_coherent for only DIAG_TRANSFER_LIMIT, and
reuse this buffer multiple times as needed to copy the data requested in
smaller chunks of size not more than DIAG_TRANSFER_LIMIT. Previously we
were reading into the caller's only after getting the complete requested
data.
Fixes: 68c03249f3 ('ath10k: convert pci_alloc_consistent() to dma_alloc_coherent()')
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On TX99 mode, instead of assuming interrupt mask non ATH9K_INT_GLOBAL,
let ath9k_hw_disable_interrupts proper set interrupt ref count.
This prevents some PCI PERR occurring specialy when setting 11b and n rates.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Change the implementation of wil log functions for consistency
with __wil_dbg_ratelimited.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adding pm_notify to allow the following:
1. Check if suspend is allowed in an earlier stage to prevent
starting the suspend procedure in case it is not allowed
2. Notify the platform driver on the suspend request
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case we fail to map one of the TSO SKB fragments, we need to
clear all the mapped descriptors, from swhead to swhead+descs_used-1.
Change the desc index calculation to
i = (swhead + descs_used - 1) % vring->size;
to prevent unmpping of (swhead + descs_used) descriptor that wasn't
mapped.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
napi_synchronize is called before releasing the vring, with the
assumption that setting txdata->enabled to 0 will prevent handling
of this vring in the next scheduled napi.
To guarantee this assumption, a memory barrier is added after disabling
the txdata.
In addition, as the ctx is zeroed in wil_tx_complete after this
descriptor is handled (protected by wmb), ctx needs to be checked
before releasing this descriptor in wil_vring_free.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
add memory barrier after allocating new rx descriptors, before
updating the hwtail.
This will guarantee that all writes to descriptors (shared memory)
are done before committing them to HW.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are 2 possible race conditions, both are solved by addition of
memory barrier:
1. wil_tx_complete reads the swhead to determine if the vring is
empty. In case the swhead was updated before the descriptor update
was performed in __wil_tx_vring/__wil_tx_vring_tso, the completion
loop will not end and as the DU bit may still be set from a previous
run, this skb can be handled as completed before it was sent, which
will lead to double free of the same SKB.
2. __wil_tx_vring/__wil_tx_vring_tso calculate the number of available
descriptors according to the swtail. In case the swtail is updated
before memset of ctx to zero is completed, we can handle this
descriptor while later on ctx is zeroed.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As there is current support for ar9002 tx99 mode, just allow
to init debugfs and enable tx99.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just some code cleanup to remove an empty if clause.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Legacy rate packets may not necessarily be having a rx status
flag of '0' always, for example management frame have flags
like RX_FLAG_ONLY_MONITOR / RX_FLAG_MACTIME_END also set
Just check 'VHT' and 'HT' flags are not set , and simply clasify it as
legacy rate packets
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WARN_ON_ONCE when we receive packets for self peer when mac80211
had not assigned a proper channel context. This scenario happens
in QCA4019 when we start the AP via hostapd in background and start
it once again in the background without killing the previous instance!
This happens intermittently when we start / stop hostapd in a while loop
(incase the hostapd is not properly killed). This results in mac80211
chancontext to be unassigned, while the self peer continuous receive
packets in target operating channel. This results in lot of call traces
in the rx path. Make this as a WARN_ON_ONCE to avoid flooding the console
which result in rebooting low memory systems, while still reporting the
warning once that we are receiving packets in target operating channel and
to indicate that something is happening which is not the expected result.
WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
[<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
(ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
[<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
[<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
[<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent changes revolving around implementing
wake_tx_queue support introduced a significant
performance regressions on some (slower, uni-proc)
systems.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 shares the same configuration with QCA99X0.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 Rx descriptor has two 32-bit words of location information
when compared to one 32-bit word in QCA99X0. To handle this difference in
rx descriptor ppdu_end, define a new ppdu_end for QCA9984 descriptor
which has the new structure to represent rx_location_info.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store pci chip secific reset funtions in struct ath10k_pci
as callbacks during early ath10k_pci_probe() and use the
callback to perform chip specific resets. This patch essentially
adds two callback in ath10k_pci, one for doing soft reset and
the other for hard reset. By using callbacks we can get rid of
those hw revision checks in ath10k_pci_safe_chip_reset() and
ath10k_pci_chip_reset(). As such this patch does not fix
any issue.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define rx_location_info in struct rx_ppdu_end_qca99x0 after
rx_pkt_end. This is to prepare rx_ppdu_end for QCA9984 chip.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Major changes:
iwlwifi
* remove IWLWIFI_DEBUG_EXPERIMENTAL_UCODE kconfig option
* work for RX multiqueue continues
* dynamic queue allocation work continues
* add Luca as maintainer
* a bunch of fixes and improvements all over
brcmfmac
* add 4356 sdio support
ath6kl
* add ability to set debug uart baud rate with a module parameter
wil6210
* add debugfs file to configure firmware led functionality
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXNbEBAAoJEG4XJFUm622bKfAH/2CnQV7dBCT5QwEiKYoOdsCR
eTiH7OYjTPw/rjKaG3laFgFbecnfUnHoGt55WKqRY58JycLza+SPTTv57hFTnOl+
4kDhUEjUggxMs5BRb3H7wtcnQVs/pTkgqKqwUrmFNkG6idENQgorK6DG4SNCwIdf
JrmxiHcN73xSATxlduoA9bGpluW3OvnFfRrJfyT6UBWZaFqFe3qsoKDx08S2WU2z
kUI9ZUO9Ht7Q85QdLfPQI7xo54dXo9a+8v3yc7fNFbcu1s8cqeYuofXfypjK7H/B
DEY96mubDnmDt8YE8yR9wStVzTr5zf39urE3o+/xSKSKhQxmNo8+x2TBSm5nFSQ=
=0HKi
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
iwlwifi
* remove IWLWIFI_DEBUG_EXPERIMENTAL_UCODE kconfig option
* work for RX multiqueue continues
* dynamic queue allocation work continues
* add Luca as maintainer
* a bunch of fixes and improvements all over
brcmfmac
* add 4356 sdio support
ath6kl
* add ability to set debug uart baud rate with a module parameter
wil6210
* add debugfs file to configure firmware led functionality
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In QCA4019, cycle counter wraparound in same fashion
as QCA988X. When the cycle counter wraparound it
resets to 0x7fffffff. Set has_shifted_cc_wraparound to
true for QCA4019 to enable the code path to handle cycle
counter wraparound for consistent survey report.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In 10.4, fw sends WMI PEER_RATECODE_LIST_EVENTID after successful
peer_assoc cmd. As of now this event is not of much use and not
implemented. Change the debug level and messsage as appropriate
to suppress "Unknown eventid: 36898".
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the ability to configure the device led to be used for notifying
the AP activity (60G device supports leds 0-2).
The host can also configure the blinking frequency of the led in
three states.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since commit cd6cfd7311
"ath9k: do not set half/quarter channel flags in AR_PHY_MODE" the
condition "rfMode & (AR_PHY_MODE_QUARTER | AR_PHY_MODE_HALF)" would
never evaluate to true.
Fix this by using the available IS_CHAN_HALF_RATE and IS_CHAN_QUARTER_RATE
marcros instead.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to keep the same for loop twice in the code.
Move the txpower cap before the loop to reduce code complexity.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since ATH9K_TX99 depends on ATH9K_DEBUGFS anyway move it there
such that "make menuconfig" will indent TX99 support below ath9k
debugging.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The same functionality as ar9003_hw_tx_power_regwrite is hardcoded in
ar9003_hw_tx99_set_txpower. Just reuse the existing ar9003_hw_tx_power_regwrite
for TX99 setup too.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During hw scan, firmware sends two channel information events (pre-
complete, complete) to host for each channel change. The snap shot of cycle
counters (rx_clear and total) between these two events are given for
survey dump. In order to get latest survey statistics of all channels, a
scan request has to be issued. In general, an AP DUT is brought up, it
won't leave BSS channel except few cases like overlapping bss or radar
detection. So survey statistics of bss channel is always referring to
older data that are collected before starting AP (either ACS/OBSS scan).
To collect latest survey information from target, firmware provides WMI
interface to read cycle counters from hardware. For each survey dump
request, BSS channel cycle counters are read and cleared in hardware.
This makes sure that behavior is in align with ath9k survey report.
So survey dump always gives snap shot of cycle counters b/w two survey
requests.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add handler to process bss channel information wmi event that
will be received upon sending pdev_chan_info_request wmi command.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI ops to send pdev_bss_chan_info_request command to target.
This command will be used to retrieve updated cycle counters and noise
floor value of current operating channel (bss channel).
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI definitions for pdev bss channel information request and
event.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is observed that while loading and unloading ath10k modules
in an infinite loop, before ath10k_core_start() completion HTT
rx frames are received, while processing these frames,
dereferencing the arvifs list code is getting hit before
initilizing the arvifs list, causing a kernel panic.
This patch initilizes the arvifs list before initilizing htt.
Fixes the below issue:
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler+0x278/0xd08 [ath10k_core])
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task+0x5f4/0xeb0 [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task [ath10k_core])
[<c0234100>] (tasklet_action+0x8c/0xec)
[<c0234100>] (tasklet_action)
[<c02337c0>] (__do_softirq+0xf8/0x228)
[<c02337c0>] (__do_softirq) [<c0233920>] (run_ksoftirqd+0x30/0x90)
Code: e5954ad8 e2899008 e1540009 0a00000d (e5943008)
---[ end trace 71de5c2e011dbf56 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Spectral related structures are accessed / modified only if ath10k
debugfs is enabled, so it makes more sense to move them under
ATH10K_DEBUGFS
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to the spec, VHT doesn't exist in 2.4GHz.
There are vendor extensions to allow a subset of VHT to work
(notably 256-QAM), but since mac80211 doesn't support those
advertising VHT capability on 2.4GHz leads to the behaviour
of reporting VHT capabilities but not being able to use any
of them due to mac80211's code requiring 80 MHz support.
Remove the VHT capabilities from 2.4GHz for now. If mac80211
gets extended to use the (likely Broadcom) vendor IEs for it
and handles the lack of 80 MHz support, it can be added back.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
After booting the wireless subsystem and uploading the NV blob to the
WCNSS_CTRL service the remote continues to do things and will not start
servicing wlan-requests for another 2-5 seconds (measured).
The downstream code does not have any special handling for this case,
but has a timeout of 10 seconds for the communication layer. By
extending the wcn36xx timeout to match this we follows the same flow for
the boot procedure and can successfully configure WiFi as wlan0 is
registered.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In idle times 60G device can enter deep sleep and turn off
its XTAL clock.
Host access triggers the device power-up flow which will hold
the AHB during XTAL stabilization until device switches from
slow-clock to XTAL clock.
This behavior can stall the PCIe bus for some arbitrary period
of time.
In order to prevent this stall, host can vote for High Latency
Access Policy (HALP) before reading from PCIe bus.
This vote will wakeup the device from deep sleep and prevent
deep sleep until unvote is done.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
RX_HTRSH interrupt sometimes triggered during device reset
procedure.
To prevent handling this interrupt when not required, unmask
this interrupt only if we are connected and mask it when
disconnected.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Network stack can try to transmit data while AP / STA is
disconnected.
Change this print-out to debug level as this should not be
handled as error.
This patch also adds wil_dbg_ratelimited, used to limit the
above print-out.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When using interrupt moderation RX_HTRSH interrupt can occur
frequently during high throughput and should not be considered
as error.
Such print-outs can degrade the performance hence should be printed
in debug print level.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
P2P search can only run on the social channel (channel 2).
When issuing a scan request on the P2P_DEVICE interface,
driver ignored the channels argument and always performed a P2P
search.
Fix this by checking the channels argument, if it is
not specified (meaning full scan) or if a non-social channel
was specified, perform a regular scan and not a P2P search.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add __func__ to wil_err and wil_info for easier
debugging.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's useful to permit the customization of the debug uart baud rate. Enable
this and send down the value to the chip if we're enabling debug.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For some reason, the 6004 HW 3.0 definition was missing the value for the
uarttx_pin (used for firmware debug). This corrects this situation.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
fix a typo (spelling mistake) in 'ath10k_start'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA6174 WLAN.RM.2.0 firmware uses max_tx_power instead of using max_reg_power
to set transmission power. The tx power was about -50dbm, after applying this
change, it become -32dbm.
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.7. Major changes:
ath10k
* implement set_tsf() for 10.2.4 branch
* remove rare MSI range support
* remove deprecated firmware API 1 support
ath9k
* add module parameter to invert LED polarity
wcn36xx
* fixes to get the driver properly working on Dragonboard 410c
Fill in the capability list with more values from the downstream driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The WCN36XX_HAL_RMV_BSSKEY_RSP carries a single u32 with "status", so we
can use the standard status check function for decoding the result.
This is the last user of the v2 status checker, so remove the struct and
helper function.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When disabling the beacon we must delete the bss before idling the link.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
EXIT_BMPS_REQ was using the command struct for ENTER_BMPS_REQ. I
spotted this when looking at command dumps.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass the multicast list to FW.
This patch also adds a way to build the smd command in place. This is
needed because the MC list command is too big for the stack.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[bjorn: dropped FIF_PROMISC_IN_BSS usage]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Knowing the association state is needed for mc filtering.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes a problem connecting to an open network after being
connected to an encrypted network.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When converting to version 1 of the config_sta struct not all
members where copied. This fixes the problem of multicast frames
not being delivered on an encrypted network.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This message does not follow the canonical format and needs it's own
parser.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This does not work with multiple sta's in a vif.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For consistency with other code.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While poking at this I also change two related things. I rename one
variable to make the names consistent. I also move one assignment of
priv_sta to the declaration to save a few lines.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some code used priv_vif and some used vif_priv. Convert all to vif_priv
for consistency.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes the code a little easier to read.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The wcn36xx FW expects a fixed size TIM PVM in the beacon template. If
supplied with a shorter than expected PVM it will overwrite the IE
following the TIM.
Squashed with fix from Jason Mobarak <jam@cozybit.com>:
Patch "wcn36xx: Pad TIM PVM if needed" has caused a regression in mesh
beaconing. The field tim_off is always 0 for mesh mode, and thus
pvm_len (referring to the TIM length field) and pad are both incorrectly
calculated. Thus, msg_body.beacon_length is incorrectly calculated for
mesh mode. Fix this.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Jason Mobarak <jam@cozybit.com>
[bjorn: squashed in Jason's fixup]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Needed for coming improvements. No functional changes.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[bjorn: restored BEACON_TEMPLATE_SIZE define to 0x180]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The Wistron DNMA-92 and Compex WLM200NX have inverted LED polarity
(active high instead of active low).
The same PCI Subsystem ID is used by both cards, which are based on
the same Atheros MB92 design.
Cc: <linux-wireless@vger.kernel.org>
Cc: <ath9k-devel@qca.qualcomm.com>
Cc: <ath9k-devel@lists.ath9k.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The LED can be active high instead of active low on some hardware.
Add the led_active_high module parameter. It defaults to -1 to obey
platform data as before.
Setting the parameter to 1 or 0 will force the LED respectively
active high or active low.
Cc: <linux-wireless@vger.kernel.org>
Cc: <ath9k-devel@qca.qualcomm.com>
Cc: <ath9k-devel@lists.ath9k.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that all firmware-N.bin related are within struct ath10k_fw_file we can
switch to use ath10k_core_fetch_firmware_api_n() and delete almost identical
ath10k_tm_fetch_utf_firmware_api_2().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to share ath10k_core_fetch_board_data_api_n() with testmode.c
refactor all firmware components to struct ath10k_fw_components. This structure
will hold firmware related files, for example firmware-N.bin and board-N.bin.
For firmware-N.bin create a new struct ath10k_fw_file which contains the actual
firmware image as well as the parsed data from the image.
Modify ath10k_core_start() to take struct ath10k_fw_components() as an argument
which makes it possible in following patches to drop some ugly hacks from
testmode.c.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This has ben deprecated years ago, I haven't heard anyone using it since and
most likely it won't even work anymore. So just remove all of it.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ah is written twice with the same value, remove one of the
redundant assignments to ah.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx power limitations at upper layers are interpreted in
the EIRP domain. When the user requests a given maximum
txpower, e.g. with: 'iw phy0 set txpower fixed 1500',
he expects the EIRP to be at or below 15dBm.
In ath9k_hw_apply_txpower(), the interpretation is
different: the antenna-gain is capped against the
current txpower limit in the regulatory, but not
against the user set value. It ensures that the
resulting EIRP is below the limit defined by the
active countrycode, but not below the value the
user requested.
In a scenario like e.g.
a) antenna_gain=6
b) countrycode limits to eirp=18
c) user set txpower=15
this will cause a setting for AR_PHY_POWER_TX_RATE
regs resulting in an EIRP > 15.
This patch ensures that antenna-gain is considered
whenever the txpower limit is adjusted and with that
the user set limits are kept.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace an explicit initialisation for one local variable at the beginning
by a conditional assignment.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
push-pull mode needs certain amount the host driver involvement for
managing queues in the host memory and packet delivery to firmware.
qca4019 wifi firmware has an option to stay in push mode for less
number of active traffic flow and then switch to push-pull mode when
the active traffic flow goes beyond the certain limit.
The advantage of staying in push mode for less active traffic is, the
host cpu consumption is reduced. qca4019 firmware supports this
flexibility of the mode switch. It takes the host driver interest
(LOW_PERF/HIGH_PERF) via WMI_EXT_RESOURCE_CFG_CMDID,
LOW_PERF - fw would stay in push mode and switch to push-pull
based on demand.
HIGH_PERF - fw would stay in push-pull mode from the boot.
To make this configuration generic, new WMI services
WMI_SERVICE_TX_MODE_PUSH_ONLY, WMI_SERVICE_TX_MODE_PUSH_PULL,
WMI_SERVICE_TX_MODE_DYNAMIC are introduced to take dynamic tx mode
switch support availability in firmware.
Based on WMI_SERVICE_TX_MODE_DYNAMIC, LOW_PERF or HIGHT_PERF is
configured to the firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch complains that since "ev->peer_id" comes from skb->data that
means we can't trust it and have to do a bounds check on it to prevent
an array overflow.
Fixes: 6942726f7f ('ath10k: add fast peer_map lookup')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon firmware assert, restart work will be triggered so that mac80211
will reconfigure the driver. An issue is reported that after restart
work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info
for operating channel. During reconfigure, since mac80211 already has
valid channel context for given radio, channel context iteration return
num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning
channel context to rx_channel when driver restart is in progress.
Cc: stable@vger.kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return value is incorrect for btcoex and peer stats debugfs
'write' entries if the user provides a value that matches with
the already available debugfs entry, this results in the debugfs
entry getting stuck and the operation has to be terminated manually.
Fix this by returning the appropriate return 'count' as we do it for
other debugfs entries like pktlog etc.
Fixes: cc61a1bbbc ("ath10k: enable debugfs provision to enable Peer Stats feature")
Fixes: c28e6f06ff ("ath10k: fix sanity check on enabling btcoex via debugfs")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
by moving common code to ar5008_hw_cmn_spur_mitigate i forgot to move
mask_m & mask_p initialisation. This coused a performance regression
on ar9281.
Fixes: f911085ffa ("ath9k: split ar5008_hw_spur_mitigate and reuse common code in ar9002_hw_spur_mitigate.")
Reported-by: Gustav Frederiksen <lkml2017@openmailbox.org>
Tested-by: Gustav Frederiksen <lkml2017@openmailbox.org>
Cc: <stable@vger.kernel.org> # 4.2+
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes checkpatch warning:
drivers/net/wireless/ath/ath10k/wmi.c:5800: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:452: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
drivers/net/wireless/ath/ath10k/mac.c:455: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
drivers/net/wireless/ath/ath10k/txrx.c:133: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1477: Prefer kernel type 'u64' over 'u_int64_t'
drivers/net/wireless/ath/ath10k/htt.h:1480: Prefer kernel type 'u64' over 'u_int64_t'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix checkpatch warnings about use of spaces with operators:
spaces preferred around that '*' (ctx:VxV)
This has been recently added to checkpatch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
MSI-X is never well-tested, might contain bugs and generally isn't
really all that useful to maintain. Also ath10k is mainly used with
shared/singly-MSI interrupt systems. Hence removing MSI range support.
This change will be useful for further cleanup in copy engine lock
and to add NAPI support.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware has addeded set_tsf vdev parameter,
hence enable it.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update 10.4 WMI vdev param to sync to current 10.4 firmware
as of 2/23/2016.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4.70.24 firmware introduces new feature to set TSF
via vdev parameter, hence implement relevant function.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will help anyone trying to use the ack-rssi reporting
feature with the host-specified TX-rate option in 10.4 firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Major changes:
iwlwifi
* support for Link Quality measurement
* more work 9000 devices and MSIx
* continuation of the Dynamic Queue Allocation work
* make the paging less memory hungry
* 9000 new Rx path
* removal of IWLWIFI_UAPSD Kconfig option
ath10k
* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)
wil6210
* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXC5ZnAAoJEG4XJFUm622bcLgIAKxTHWfcirfNpzLg39gfR/jx
vWTX8YifGdZUuQuaEJhc7pPZ6eiTyMlRLZsu9JDT0LErM6uwPKSOXkogzfiSFG00
ntXGOWfQlGdyFyQshOoHWlXSkfE7bBWpLiROgk7dS2oyObQr2ETBT/yVd1bkP6Ka
g13sgzM/a3CbxaZSllaK0S/YPQ6JhXlbeWotqOqE4SotYQD2QfLkYJiXSFRXNcQl
OWDPCTjI3yybOVRLTnLMn2CoWrRqtUElwXaWBKJPhgY3EyxlU6R6UPw8OL8DvXIw
EedpflIekKahwZJbipqdkKbhpxinUAa9kPsSkfCtlPJQWsiQvdwpG7R5KQmJ8Lc=
=A2Lw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-04-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
iwlwifi
* support for Link Quality measurement
* more work 9000 devices and MSIx
* continuation of the Dynamic Queue Allocation work
* make the paging less memory hungry
* 9000 new Rx path
* removal of IWLWIFI_UAPSD Kconfig option
ath10k
* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)
wil6210
* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.7. Major changes:
ath10k
* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)
wil6210
* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
In ath9k_hif_usb_rx_stream(), i is initialised in the for loop it's
used in.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
[Rewrote commit message]
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"(thermometer < 0) ? 0 : (thermometer == X)" is equivalent to
"thermometer == X" for X >= 0.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
[Updated commit message]
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Decrement num_mpdus_ready only when rx amsdu is processed successfully.
Not doing so, will result in leak and impact stabilty under low memory
cases. Also commit 3128b3d8a2 ("ath10k: speedup htt rx descriptor
processing for rx_ind") missed to removed unused skb list rx_q.
Fixes: 3128b3d8a2 ("ath10k: speedup htt rx descriptor processing for rx_ind")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca99x0 and qca4019 solutions limit probe responses transmissions.
Logging warning message for each probe response drop is flooding
kernel log unnecessary with " failed to increase tx mgmt pending
count: -16, dropping". Hence reducing log level to debug.
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
pre-calibration is meant for qca4019 which contains only caldata
whereas calibration file is used by ar9888 and qca99x0 that contains
both board data and caldata. So by definition both pre-cal-file and
cal-file can not coexist. Keeping them in shared memory (union), is
breaking boot sequence of qca99x0. Fix it by storing both binaries
in separate memories. This issue is reported in ipq8064 platform which
includes caldata in flash memory.
Fixes: 3d9195ea19 ("ath10k: incorporate qca4019 cal data download sequence")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When HW crypto is used, there's no need for the CCMP/GCMP MIC to
be available to mac80211, and the hardware might have removed it
already after checking. The MIC is also useless to have when the
frame is already decrypted, so allow indicating that it's not
present.
Since we are running out of bits in mac80211_rx_flags, make
the flags field a u64.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If no valid ADC randomness output, ath9k rng will continuously
reading ADC, which will cause high CPU load. So increase the
delay to wait for ADC ready.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114261
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are many valid WMI commands with only header without any
additional payload. Such WMI commands could not be sent using
the debugfs wmi_send facility. Fix the code to allow sending
of such commands.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
BugLink: http://bugs.launchpad.net/bugs/972604
Commit 09c9bae26b ("ath5k: add led pin
configuration for compaq c700 laptop") added a pin configuration for the Compaq
c700 laptop. However, the polarity of the led pin is reversed. It should be
red for wifi off and blue for wifi on, but it is the opposite. This bug was
reported in the following bug report:
http://pad.lv/972604
Fixes: 09c9bae26b ("ath5k: add led pin configuration for compaq c700 laptop")
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Check and parse Rx MAC timestamp when firmware sets its flag
to status variable.
10.4 firmware adds it in Rx beacon frame only at this moment.
Drivers and mac80211 may utilize it to detect such clockdrift
or beacon collision and use the result for beacon collision
avoidance.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since tx completion and rx indication processing are moved out
of txrx tasklet and rx ring lock contention also removed from txrx
for rx_ind messages, it would be efficient to combine both replenish
and txrx tasks. Refill threshold is adjusted for both AP135 and AP148
(low and high end systems). With this adjustment in AP135, TCP DL is
improved from 603 Mbps to 620 Mbps and UDP DL is improved from 758 Mbps
to 803 Mbps. Also no watchdog are observed on UDP BiDi.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Whenever htt rx indication i.e target to host messages are received
on rx copy engine (CE5), the message will be freed after processing
the response. Then CE 5 will be refilled with new descriptors at
post rx processing. This memory alloc and free operations can be avoided
by reusing the same descriptors.
During CE pipe allocation, full ring is not initialized i.e n-1 entries
are filled up. So for CE 5 full ring should be filled up to reuse
descriptors. Moreover CE 5 write index will be updated in single shot
instead of incremental access. This could avoid multiple pci_write and
ce_ring access. From experiments, It improves CPU usage by ~3% in IPQ4019
platform.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. For diag register read and write
operations, 'paddr' is stored in transfer context. ath10k doesn't rely
on the meta/transfer_id. So the unused output arguments {bufferp, nbytesp
and transfer_idp} are removed from CE recv_next completion.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Except qca61x4 family chips (qca6164, qca6174), copy engine 5 is used
for receiving target to host htt messages. In follow up patch, CE5
descriptors will be reused. In such case, same API can not be used as
htc layer callback where the response messages will be freed at the end.
Hence register new API for HTC layer that free up received message and
keep the message handler common for both HTC and HIF layers.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In follow up patch, htt rx descriptors will be reused instead of
dealloc and refill. To achieve that htt rx indication messages
should not be deferred and should be processed in pci tasklet itself.
Also from rx indication message, mpdu_count alone is used. So it is
maintained as atomic variable and all rx amsdu handlers are done
processed from txrx tasklet. This change get rid of rx_compl_q usage.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make amsdu handlers (i.e amsdu_pop and rx_h_handler) common to both
rx_ind and frag_ind htt events. It is sufficient to hold rx_ring lock
for amsdu_pop alone and no need to hold it until the packets are
delivered to mac80211. This helps to reduce rx_lock contention as well.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The fw descriptor was never used and probably never will be. It makes
little sense to maintain support for it. Remove it and simplify rx
processing. This will make it easier to optimize rx processing later
as well.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To optmize CPU usage htt rx descriptors will be reused instead of
refilling it for htt rx copy engine (CE5). To support that all htt rx
indications should be proecssed at same context. Instead of queueing
actual indication message, queue copied message for txrx processing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To optimize CPU usage htt rx descriptors will be reused instead of
refilling it for htt rx copy engine (CE5). To support that all htt rx
indications should be processed at same context. FIFO queue is used
to maintain tx completion status for each msdu. This helps to retain
the order of tx completion.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx duration support for per station is part of extended peer
stats, enable provision to parse the same and provide backward
compatibility based on the 'stats_id' event
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add API support for Extended Resource Configuration for 10.4. This
is useful to enable new features like Peer Stats, LTEU etc if the
firmware advertises support for the service. This is also done to
provide backward compatibility with older firmware. Also for clarity
send default host platform type as 'WMI_HOST_PLATFORM_HIGH_PERF',
though this should not make any difference in functionality
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Provide a debugfs entry to enable/ disable Peer Stats feature.
Peer Stats feature is for developers/users who are more interested
in studying in Rx/Tx stats with multiple clients connected, hence
disable this by default. Enabling this feature by default results
in unneccessary processing of Peer Stats event for every 500ms
and updating peer_stats list (allocating memory) and cleaning it up
ifexceeds the higher limit and this can be an unnecessary overhead
during long run stress testing.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca4019 calibration data is stored in the host memory and it's mandatory
to download it even before reading board id and chip id from the target.
Also, there is a need to execute otp (download and run) twice, one after
cal data download and another one after board data download.
Existing cal data file name 'cal-<bus>-<id>.bin' and device tree entry
'qcom,ath10k-calibration-data' used in ath10k has assumption that it
carries other data (like board data) also along with the calibration data.
But, qca4019 cal data contains pure calibration data (doesn't include
any other info). So, using existing same cal file name and DT entry
in qca4019 case would alter the purpose of it. To avoid this, new cal
file name 'pre-cal-<bus>-<id>.bin' and new device tree entry name
'qcom,ath10k-pre-calibration-data are introduced.
Overall qca4019's firmware download sequence would look like,
1) Download cal data (either from a file or device tree entry)
at the address specified by target in the host interest area
member "hi_board_data".
2) Download otp and run with 0x10 (PARAM_GET_EEPROM_BOARD_ID)
as a argument.
At this point, otp will take back up of downloaded cal data
content in another location in the target and return valid
board id and chip id to the host.
3) Download board data at the address specified by target
in host interest area member "hi_board_data".
4) Download otp and run with 0x10000 (PARAM_FLASH_SECTION_ALL) as
a argument.
Now otp will apply cal data content from it's backup on top
of board data download in step 3 and prepare final data base.
5) Download code swap and athwlan binary content.
Above sequences are implemented (step 1 to step 4) in the name of
pre calibration configuration.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_download_cal_dt() compares obtained cal data content length
against QCA988X_CAL_DATA_LEN (2116 bytes). It was written by keeping
qca988x in mind. In fact, cal data length is more chip specific.
To make ath10k_download_cal_dt() more generic and reusable for other
chipsets (like qca4019), cal data length is moved to hw_params.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Both ath10k_download_cal_file() and ath10k_download_cal_dt() uses
hard coded file pointer (ar->cal_file) and device tree entry
(qcom,ath10k-calibration-data) respectively to get calibration
data content.
There is a need to use those two functions in qca4019 calibration
download sequence with different file pointer and device tree entry name.
Modify those two functions to take cal data location as an argument.
So that it can serve the purpose for other file pointer and device
tree entry.
This is just preparation before adding actual qca4019 calibration
download sequence. No functional changes.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If device failed to init during early probing
(which is quite rare) it triggered driver to
compute crc before ar->firmware was ready causing
an oops.
Fixes: 3e58044b61 ("ath10k: print crc32 checksums for firmware and board files")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents tx hangs or hiccups if pull-push
supporting firmware defines per-txq thresholds or
switches modes dynamically.
Fixes: 299468782d ("ath10k: implement wake_tx_queue")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The wake_tx_queue/push_pending logic had a bug
which could stop queues indefinitely effectivelly
breaking traffic.
Fixes: 299468782d ("ath10k: implement wake_tx_queue")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Results obtained from scan can be used for spectrum management by
doing something like building information of preferred channel
lists and sharing them with stations around. It is to be noted
that traffic to the connected stations would be affected during
the scan.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is observed that, we are disabling the packet log if we write same
value to the pktlog_filter for the second time. Always enable pktlogs
on non zero filter.
Fixes: 90174455ae ("ath10k: add support to configure pktlog filter")
Cc: stable@vger.kernel.org
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_core_probe_fw() simply returns error without freeing
cached firmware file content when get board id operation fails.
Free cached fw bin data in failure case to avoid memory leak.
Fixes: db0984e51a ("ath10k: select board data based on BMI chip id and board id")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames that are transmitted via MGMT_TX are using reserved descriptor
slots in firmware. This limitation is for the htt_mgmt_tx path itself,
not for mgmt frames per se. In 16 MBSSID scenario, these reserved slots
will be easy exhausted due to frequent probe responses. So for 10.4
based solutions, probe responses are limited by a threshold (24).
management tx path is separate for all except tlv based solutions. Since
tlv solutions (qca6174 & qca9377) do not support 16 AP interfaces, it is
safe to move management descriptor limitation check under mgmt_tx
function. Though CPU improvement is negligible, unlikely conditions or
never hit conditions in hot path can be avoided on data transmission.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Whenever firmware is configuring operating channel during scan or
home channel, channel change event will be indicated to host. In some
cases (device probe/ last vdev down), target will be configured to
default channel whereas host is unaware of target's operating channel.
This leads to packet drop due to unknown channel and kernel log will be
filled up with "no channel configured; ignoring frame(s)!". Fix that
by handling HTT_T2H_MSG_TYPE_CHAN_CHANGE event.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A cleanup patch in linux-3.18 moved around some code in the ath9k
driver and left some code to be indented in a misleading way,
made worse by the addition of some new code for p2p mode, as
discovered by a new gcc-6 warning:
drivers/net/wireless/ath/ath9k/init.c: In function 'ath9k_set_hw_capab':
drivers/net/wireless/ath/ath9k/init.c:851:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
hw->wiphy->iface_combinations = if_comb;
^~
drivers/net/wireless/ath/ath9k/init.c:847:3: note: ...this 'if' clause, but it is not
if (ath9k_is_chanctx_enabled())
^~
The code is in fact correct, but the indentation is not, so I'm
reformatting it as it should have been after the original cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 499afaccf6 ("ath9k: Isolate ath9k_use_chanctx module parameter")
Fixes: eb61f9f623 ("ath9k: advertise p2p dev support when chanctx")
Signed-off-by: David S. Miller <davem@davemloft.net>
Code that was added back in 2.6.38 has an obvious overflow
when accessing a static array, and at the time it was added
only a code comment was put in front of it as a reminder
to have it reviewed properly.
This has not happened, but gcc-6 now points to the specific
overflow:
drivers/net/wireless/ath/ath9k/eeprom.c: In function 'ath9k_hw_get_gain_boundaries_pdadcs':
drivers/net/wireless/ath/ath9k/eeprom.c:483:44: error: array subscript is above array bounds [-Werror=array-bounds]
maxPwrT4[i] = data_9287[idxL].pwrPdg[i][4];
~~~~~~~~~~~~~~~~~~~~~~~~~^~~
It turns out that the correct array length exists in the local
'intercepts' variable of this function, so we can just use that
instead of hardcoding '4', so this patch changes all three
instances to use that variable. The other two instances were
already correct, but it's more consistent this way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 940cd2c12e ("ath9k_hw: merge the ar9287 version of ath9k_hw_get_gain_boundaries_pdadcs")
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain 6004 firmware releases redefine the WMI_TXE_NOTIFY_EVENTID event
number and sends the new event frequently. However it doesn't have the
tx-err-notify feature and thus this firmware capability flag isn't set on
the firmware package. By guarding the processing of this event by the same
method we guard the sending of the WMI_SET_TXE_NOTIFY_CMDID command, we
can ignore the spurious event that we don't know how to process.
Without this change we call cfg80211_cqm_txe_notify() with possibly bad
data.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow to set wl_active_time and wl_qc_time for SOC chips, also adjust
bt_time_extend and bt_first_slot_time.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The registers of AR_GPIO_INPUT_MUX1 and AR_GPIO_PDPU were removed
from SOC chips, fix invalid accessing
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add bits definition for AR_BT_COEX_MODE2 and AR_BT_COEX_MODE3, which
needed by SOC chips (AR9340, AR9531, AR9550, AR9561).
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add new platform data to allow override BTCoex default pin.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make ath_init_leds() and ath_deinit_leds() pairs as the only
API to set leds, also removed direction configuration from
ath9k_start() and ath9k_stop(). So the initial is more clear
now.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For SOC GPIOs, should call ath9k_hw_gpio_free() to release
the GPIO resource.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 61b559dea4 ("ath9k: add extra GPIO led support")
added ath9k to support access SOC's GPIOs, but implemented
in a separated API: ath9k_hw_request_gpio().
So this patch make the APIs more common, to support both
of WMAC and SOC GPIOs. The new APIs as below,
void ath9k_hw_gpio_request_in();
void ath9k_hw_gpio_request_out();
void ath9k_hw_gpio_free();
NOTE, the BSP of the SOC chips(AR9340, AR9531, AR9550, AR9561)
should set the corresponding MUX registers correctly.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define correct GPIO numbers and MASK bits to indicate the WMAC
GPIO resource.
Allow SOC chips(AR9340, AR9531, AR9550, AR9561) to access all GPIOs
which rely on gpiolib framework. But restrict SOC AR9330 only to
access WMAC GPIO which has the same design with the old chips.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These lines belong inside the if-statement above, not in the
main body of the switch.
Found by smatch.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
smatch said:
drivers/net/wireless/ath/ath5k/phy.c:1449 ath5k_hw_channel() warn: inconsistent indenting
drivers/net/wireless/ath/ath5k/reset.c:637 ath5k_hw_on_hold() warn: inconsistent indenting
drivers/net/wireless/ath/ath5k/reset.c:702 ath5k_hw_nic_wakeup() warn: inconsistent indenting
All of these lines were indented a tabstop too far.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit f49c90db4d ("ath9k: Add a macro to identify PCOEM chips")
defined AR_SREV_9003_PCOEM macro, its more clear to use the macro
instead of checking one by one. Also removed PCOEM chips checking
in the callback of ar9003_hw_do_pcoem_manual_peak_cal() which only
for PCOEM chips.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW peak detect calibration would fail, enable all ar9300
chips manual peak calibration instead.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW peak detect calibration would fail for AR9300 chips and
we went for implementing the SW way of doing it instead of
HW doing the peak detect calibration.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW peak detect calibration would fail for AR9300 chips and
we went for implementing the SW way of doing it instead of
HW doing the peak detect calibration.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW peak detect calibration would fail for AR9300 chips and
we went for implementing the SW way of doing it instead of
HW doing the peak detect calibration.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW peak detect calibration would fail for AR9300 chips and
we went for implementing the SW way of doing it instead of
HW doing the peak detect calibration.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW peak detect calibration would fail for AR9300 chips and
we went for implementing the SW way of doing it instead of
HW doing the peak detect calibration.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW peak detect calibration would fail for AR9300 chips and
we went for implementing the SW way of doing it instead of
HW doing the peak detect calibration.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW peak detect calibration would fail for AR9300 chips and
we went for implementing the SW way of doing it instead of
HW doing the peak detect calibration.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW peak detect calibration would fail for AR9300 chips and
we went for implementing the SW way of doing it instead of
HW doing the peak detect calibration.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW peak detect calibration would fail for AR9300 chips and
we went for implementing the SW way of doing it instead of
HW doing the peak detect calibration.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 14c5932805 ("ath9k: Update QCA953x initvals")
disabled HW peak detect calibartion on QCA953x 1.0, which
should also be applied on 2.0.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Check and set Rx MAC timestamp when firmware indicates it.
Firmware adds it in Rx beacon frame only at this moment.
Driver and mac80211 may utilize it to detect such clockdrift
or beacon collision and use the result for beacon collision
avoidance.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now only WMI originating mgmt frames were
reported to mac80211. Management frames on HTT
were basically dropped (except frames which looked
like management but had FCS error).
To allow sniffing all frames (including offloaded
frames) without interfering with mac80211
operation and states a new rx_flag was introduced
and is not being used to distinguish frames and
classify them for mac80211.
Signed-off-by: Grzegorz Bajorski <grzegorz.bajorski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Import new headers from my firmware branch:
<https://github.com/chunkeey/carl9170fw>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add module parameter oob_mode. Takes effect the next time
the interface is brought up and FW is loaded. Puts the FW
in special "out of the box" (OOB) mode which is used for
diagnostics and certification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When starting a PCP, pass the is_go flag to firmware in
wmi_pcp_start. This flag indicates whether we started
a PCP which is also a GO(P2P group owner) or just a regular
PCP.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW crashed with no_fw_recovery mode enabled, user space
could still call wil_cfg80211_change_iface quickly to change
interface type, and this would cause recovery to proceed and
FW crash logs may be lost.
Fix this problem by not resetting the FW in case no_fw_recovery
is enabled.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix a debug message related to IOCTL that was incorrectly logged
with the MISC category, and move it inside wil_ioctl so it will
always be logged even if we call wil_ioctl from other places.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix 2 race conditions found during test runs of P2P discovery:
1. Because wil_p2p_cancel_listen was not protected, user space
could start a new P2P listen/search before wmi_stop_discovery
completed. This caused a crash in the firmware.
2. In P2P listen, when listen timer expires and user space calls
cancel_remain_on_channel at the same time, code could send the
cfg80211_remain_on_channel_expired notification twice.
Added protections with wil->mutex to several places that call
wmi_stop_discovery.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added support for the P2P_DEVICE virtual interface. This interface
is intended for P2P management operations such as discovery and
GO negotiation. Normally it is implemented by drivers to allow
a separate interface for P2P management with its own MAC address,
but for 11ad drivers it is needed to support P2P search, since it
cannot otherwise be separated from normal scan.
Since we only support a single interface/MAC address, we can't
easily separate between primary and P2P_DEVICE interfaces.
For example when a management packet arrives we can't tell for
which interface it is intended. To work around this, we store
a pointer to the interface where the last "radio operation" was
triggered such as scan or remain on channel, and we forward
management packets and scan results to this interface.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
supporting p2p_find, p2p_listen and p2p_connect
Use updated cfg80211_get_bss API (additional argument)
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the ability to notify the platform driver on different
events, such as FW crash, pre reset and FW ready.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
For example, stations inside a PBSS can communicate directly, and
the PCP role can be transferred between stations.
This change adds PBSS support, and has 2 main parts:
1. When starting an AP, add an option to start as a PCP instead.
This is implemented by a new PBSS flag which is passed as part of
the cfg80211_ap_settings structure.
2. When connecting to a BSS, add an option to connect to a PCP
instead of an AP. This is again implemented by a new PBSS flag,
added to the cfg80211_connect_params structure.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Switch to auto-generated version of wmi.h which is maintained
by FW team. This will allow better sync between teams in the
future and avoid bugs because of unexpected API changes.
The wmi.h will have many differences but most are cosmetic.
It also includes these real differences:
1. is_go parameter added to BCON_CTRL and START_PCP commands.
2. max_rx_pl_per_desc added to CFG_RX_CHAIN command.
3. various small API updates that are not currently used by
driver.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for discovery mode during scan. When discovery mode
is active, station transmits special beacons while scanning.
This can optimize the scan mainly when there is only one AP/PCP
around.
Discovery mode is implicitly used by firmware during P2P search.
Since there is currently no use case where user space has a
reason to directly control discovery mode, we expose it only
through a debugfs flag.
Also fix name confusion in the wmi_scan_type enumeration.
The type previously called WMI_LONG_SCAN is actually
WMI_ACTIVE_SCAN.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
MAC address of wil6210 was not set in wiphy
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wmi_evt_connect doesn't check if the connect event is received for
an already connected station.
This can lead to memory leak as a new vring is allocated without
freeing the previously allocated vring and to unexpected behavior
of nl80211 layer due to unexpected notification of a new station.
Add a check in wmi_evt_connect in AP mode to verify that the requested
CID is not associated to an already connected station.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI synchronous handling has changed and WMI calls that provide
a buffer for the reply are completed in the WMI interrupt context.
This allows sending the RX and TX BACK commands from the WMI event
handler without the need for the worker thread.
This is a better approach as it can decrease the handshake time
in the connect flow and prevent race conditions in case of fast
disconnects. An example for such a race is handling of wil_back_rx_handle
during a disconnect event, as wil_back_rx_handle is not protected by
the wil mutex and a disconnect can be handled after sta->status is
verified as connected.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 166de3f189 ("ath10k: remove supported chain mask") had revealed
an issue on monitor mode. Configuring NSS upon monitor interface
creation is causing target assert in all qca9888x and qca6174 firmware.
Firmware assert issue can be reproduced by below sequence even after
reverting commit 166de3f189 ("ath10k: remove supported chain mask").
ip link set wlan0 down
iw wlan0 set type monitor
iw phy0 set antenna 7
ip link set wlan0 up
This issue is originally reported on qca9888 with 10.1 firmware.
Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation")
Cc: stable@vger.kernel.org
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of HTT Tx descriptors and qcache peer
limit aren't hw-specific. In fact they are
firmware specific and should not be placed in
hw_params.
The QCA4019 limits were submitted with the peer
flow control firmware only and to my understanding
there's no non-peer-flow-ctrl QCA4019 firmware.
However QCA99X0 is planned to run firmware
supporting the feature as well. Therefore this
patch enables QCA99X0 to use 2500 tx descriptors
whenever possible instead of just 1424.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA4019 can queue up to 2500 frames at a time.
This means it requires roughly 5000 entires on the
ring to work properly. Otherwise random tx failure
may occur.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The current/old tx path design was that host, at
its own leisure, pushed tx frames to the device.
For HTT there was ~1000-1400 msdu queue depth.
After reaching that limit the driver would request
mac80211 to stop queues. There was little control
over what packets got in there as far as
DA/RA was considered so it was rather easy to
starve per-station traffic flows.
With MU-MIMO this became a significant problem
because the queue depth was insufficient to buffer
frames from multiple clients (which could have
different signal quality and capabilities) in an
efficient fashion.
Hence the new tx path in 10.4 was introduced: a
pull-push mode.
Firmware and host can share tx queue state via
DMA. The state is logically a 2 dimensional array
addressed via peer_id+tid pair. Each entry is a
counter (either number of bytes or packets. Host
keeps it updated and firmware uses it for
scheduling Tx pull requests to host.
This allows MU-MIMO to become a lot more effective
with 10+ clients.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware 10.4.3 onwards can support a pull-push Tx
model where it shares a Tx queue state with the
host.
The host updates the DMA region it pointed to
during HTT setup whenever number of software
queued from (on host) changes. Based on this
information firmware issues fetch requests to the
host telling the host how many frames from a list
of given stations/tids should be submitted to the
firmware.
The code won't be called because not all
appropriate HTT events are processed yet.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This implements very basic support for software
queueing. It also contains some knobs that will be
patched later.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This merely adds some parsing, generation and
sanity checks with placeholders for real
code/functionality to be added later.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The pull-push functionality of 10.4 will be based
on peer_id and tid. These will need to be mapped,
eventually, to ieee80211_txq to be used with
ieee80211_tx_dequeue().
Iterating over existing stations every time
peer_id needs to be mapped to a station would be
inefficient wrt CPU time.
The new firmware, which will be the only user of
the code flow-wise, will guarantee to use low
peer_ids first so despite peer_map's apparent huge
size d-cache thrashing should not be a problem.
Older firmware hot paths will effectively not use
peer_map.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.4.3 firmware with congestion control
guarantees that each peer has only a single
peer_id mapping.
The 1:1 mapping isn't the case for older firmwares
(e.g. 10.4.1, 10.2, 10.1) but it should not
matter. This 1:1 mapping is going to be only used
by future code which inherently (flow-wise) is for
10.4.3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx pending counter logic assumed that the sk_buff
is already known and hence was performed in HTT
functions themselves.
However, for the sake of future wake_tx_queue()
usage the driver must be able to tell whether it
can submit more frames to firmware before it
dequeues frame from ieee80211_txq (and thus long
before HTT Tx functions are called) because once a
frame is dequeued it cannot be requeud back to
mac80211.
This prepares the driver for future changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some future changes will need to determine final
tx method early on. Prepare the code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prepares the code for future reuse with
ieee80211_txq and wake_tx_queue() in mind.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.6. Major changes:
ath10k
* dt: add bindings for ipq4019 wifi block
* start adding support for qca4019 chip
ath9k
* add device ID for Toshiba WLM-20U2/GN-1080
* allow more than one interface on DFS channels
JP WiFi certification for bandwidth of channel 14 failed, the OBW
is lower than the requirement. Clear the bb filter calibration power
threshold to increase OBW(+2). The fix only for qca9531 chip now.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some configurations, this function uses more than the warning limit
of 1024 bytes:
drivers/net/wireless/ath/ath9k/ar9003_aic.c: In function 'ar9003_aic_cal_post_process':
drivers/net/wireless/ath/ath9k/ar9003_aic.c:434:1: error: the frame size of 1040 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
It turns out that there are two large arrays on the stack here, but
almost all the data in them is never used outside of the loop in
which it gets written, so we can replace the array with a single
instance.
The .valid flag is used later, so I'm replacing the array of structures
with an array of bools. An obvious follow-up optimization would be
to replace it with a bitmask and set_bit()/find_first_bit()/
find_last_bit()/... operations. However, I have not tested this patch,
so I sticked to the simpler transformation that does the job of
reducing the stack usage to a harmless level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make NF load complete quickly and reliably. NF load execution
is delayed by HW to end of frame if frame Rx or Tx is ongoing.
Increasing timeout to max frame duration. If NF cal is ongoing
before NF load, stop it before load, and restart it afterwards.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
First check for the device state before enabling / disabling
btcoex, also return a proper error value. Enabling / disabling
btcoex ideally does a f/w + ath10k_core_restart so the checks
that are applicable for 'simulate_fw_crash' shall be applicable
for this as well
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To enable per peer stats feature we are reducing the number of peers.
Firmware has introduced tx stats feature. We have memory limitation in
firmware to add these additional bytes.
These are the new variables introduced in the firmware.
======== =======================
Variable Bytes required/per rate
======== =======================
TX success packets 1
TX failed packets 1
Retry packets 1
Success bytes 2
TX failed bytes 2
Retry bytes 2
Tx duration 4
Rate 1
Bw and AMPDU flags 1
Total 16 (because of allocation in word pattern)
Firmware sends these tx_stats in pktlog.
If we consider 4 feedbacks at a time, Frimware need about ~1K memory for coding
and 8192 bytes required / per rate [ 4*16*128(peers)].
To accommodate this firmware needs to reduce 10 peers.
This fixes a firmware crash with firmware-5.bin_10.2.4.70.22-2.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On multicore systems, it is possible that txrx tasket can run
in parallel with pci tasklet (i.e smp affinity of ath10k irq is
assigned to multiple CPUs). Feeding and consuming from the same
rx completion list leads to txrx tasklet runs for longer period.
Prevent this by processing a snapshot of rx queue by moving list
into temporary list. Consecutive received frames will be processed
in next batch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Received frame indications are queued into a skb list and latest
processed by txrx tasklet. This skb queue is protected by htt rx lock.
Since the entire rx processing till delivering frame to mac80211 and
replenish tasks are processed under rx_lock protection, there might be
some delay in queuing newly received rx frame into that list on
multicore systems. Optimize this by using skb list lock while accessing
rx completion queue instead of htt rx lock.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath10k_pci_hif_exchange_bmi_msg() function may return the positive
value EIO instead of -EIO in case of error.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
pktlog data is different between firmware variants (eg. 10.2 vs 10.4). To
have a unified user space script to decode pktlog trace events generated,
it is desirable to know which firmware variant has provided the events and
thereby decode the pktlogs appropriately. Hardware revision (hw_rev) helps
to determine the firmware variant sending these trace events. So add hw_rev
to trace events.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently, we are providing wrong payload data of pktlog to trace points.
Data we receive from FW through copy engine 8 contains pktlog data alone.
We don't need to parse anything in driver before handing it to trace
points.
Fixes: afb0bf7f53 ("ath10k: add support for pktlog in QCA99X0")
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We periodically receive f/w stats event for updating
the rx duration and there is no reason to keep on appending
the f/w stats peer list, as this gets completely cleaned up when
the user polls for f/w stats {pdev, vdev, peer stats}. Only don't
print the warning message in the case PEER_STATS service is enabled
Fixes: 856e7c3 ("ath10k: add debugfs support for Per STA total rx duration")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We are not updating peer stats rx_duration periodically
unless the user one polls for fw_stats, this is because
we discard the update event since pdev list is empty. Fix
this by updating rx duration periodically irrepective of checks
for pdev list (irrespective of ping-pong response)
Fixes: 856e7c3 ("ath10k: add debugfs support for Per STA total rx duration")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
len has been initialized with a value of 0 and buf_len with 4096. There
is no way that this condition (len > buf_len) can be true now.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for 11ad devices.
Add support for PBSS by introducing a new PBSS flag attribute.
The PBSS flag is used in the START_AP command to request starting
a PCP instead of an AP, and in the CONNECT command to request
connecting to a PCP instead of an AP.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some of the parameter like tx/rx chain mask, number of htt tx desc,
qcache active peer count, etc goes via wmi init cmd to qca4019 firmware
are different.
To make use of 10.4 gen_init function for qca4019, change wmi service
ready handler and 10.4 wmi init functions to adapt qca4019 specific
init values.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a new entry in hw_params_list for qca4019 with list of
it's own details.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Abstraction layer for vdev subtype is added to solve
subtype mismatch and to give flexible compatibility
among different firmware revisions.
For instance, 10.2 and 10.4 firmware has different
definition of their vdev subtypes for Mesh.
10.4 defined subtype 6 for 802.11s Mesh while 10.2 uses 5.
Hence use the abstraction API to get right subtype to use.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Interface type P2P_GO can be checked by either arvif->vdev_type
and arvif->vdev_subtype or vif->type and vif->p2p.
Use later one to avoid more cpu consumption that could happen
when subtype abstraction layer change is introduced.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update 10.4 WMI service map to sync to the latest 10.4 firmware
as of 1/20/2016.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_10_4_SERVICE_MESH bit is for non IEEE802.11s Mesh.
Hence rename it to WMI_10_4_SERVICE_MESH_NON_11S.
Also add _11S as post-fix to each of WMI_SERVICE_MESH and
WMI_VDEV_SUBTYPE_MESH specifying the service is for 11s Mesh.
This will help users to distinguish 11s Mesh from non 11s Mesh.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx vring needs to be enlarged to get better
performance for traffic over 2Gbps.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case there are multiple WMI commands with the same reply_id,
the following scenario can occur:
- Driver sends the first command to the device
- The reply didn’t get on time and there is timeout
- Reply_id, reply_buf and reply_size are set to 0
- Driver sends second wmi command with the same reply_id as the first
- Driver sets wil->reply_id
- Reply for the first wmi command arrives and handled by wmi_recv_cmd
- As its ID fits the reply_id but the reply_buf is not set yet it is
handled as a reply with event handler, and WARN_ON is printed
This patch guarantee atomic setting of all the reply variables and
prevents the above scenario.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211_ops.disconnect() should wait for disconnect flow to
complete. If it does not, internal state becomes out of sync with
one in cfg80211. If one does stress test connect/disconnect
sequence, cfg80211 will issue next connect before disconnect
completed internally.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wil_tx_vring locks the vring_tx_data lock before accessing the TX
vring to check if it is enabled and valid for use.
In case of quick disconnect / connect events for the same station,
spin_lock(&txdata->lock) can be called during the lock initialization
in the vring init function.
To prevent such a race, the TX vrings spin lock should be initialized
once during wil6210 driver initialization.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
