Now that all the needed pieces are in place implement suspend support QCA6390
PCI devices. All other devices will return -EOPNOTSUPP during suspend. The
suspend is implemented by switching the firmware to WoW mode during suspend, so
the firmware will be running on low power mode while host is in suspend.
At the moment we are not able to shutdown and fully power off the device due to
bugs in MHI subsystem, so WoW mode is a workaround for the time being.
During suspend we enable WoW mode, disable CE irq and DP irq, then put MHI to
suspend state. During resume, driver resumes MHI firstly, then enables CE irq
and dp IRQ, and sends WoW wakeup command to firmware.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-11-git-send-email-kvalo@codeaurora.org
Firmware will check all the pipes before entering WoW mode during suspend. If
ATH11K_HTC_FLAG_NEED_CREDIT_UPDATE is set, firmware treats this pipe needed to
return credit even though it's actually not required. If any pipe needs to
return credit, the suspend_complete message doesn't send to host but is
dropped. So host gets time out and WoW suspend failed.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-8-git-send-email-kvalo@codeaurora.org
Just when resume from WoW, the write to select_window doesn't take
effect immediately, so read the register again to ensure the write
operation is finished.
Another change is to reset select_window to ZERO because this
register isn't restored after WoW, so the content of this register
becomes ZERO too.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-4-git-send-email-kvalo@codeaurora.org
Currently 6G specific tlvs have duplicate entries which is causing
scan failures. Fix this by removing the duplicate entries of the same
tlv. This also fixes out-of-bound memory writes caused due to
adding tlvs when num_hint_bssid and num_hint_s_ssid are ZEROs.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Fixes: 74601ecfef ("ath11k: Add support for 6g scan hint")
Reported-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-7-git-send-email-kvalo@codeaurora.org
There was no way to detect if the firmware crashed so add a warning. At the
moment the firmware is not restarted or anything like that, so when this
happens ath11k modules need to be reloaded.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-2-git-send-email-kvalo@codeaurora.org
When it has more than one restart_work queued meanwhile, the 2nd
restart_work is very easy to break the 1st restart work and lead
recovery fail.
Add a flag to allow only one restart work running untill
device successfully recovered.
It already has flag ATH10K_FLAG_CRASH_FLUSH, but it can not use this
flag again, because it is clear in ath10k_core_start. The function
ieee80211_reconfig(called by ieee80211_restart_work) of mac80211 do
many things and drv_start(call to ath10k_core_start) is 1st thing,
when drv_start complete, it does not mean restart complete. So it
add new flag and clear it in ath10k_reconfig_complete, because it
is the last thing called from drv_reconfig_complete of function
ieee80211_reconfig, after it, the restart process finished.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746bead6a0-d5e97c66-dedd-4b92-810e-c2e4840fafc9-000000@us-west-2.amazonses.com
In some devices difference in chip-id should be enough to pick
the right BDF. Add another support for chip-id based BDF selection.
With this new option, ath10k supports 2 fallback options.
The board name with chip-id as option looks as follows
board name 'bus=snoc,qmi-board-id=ff,qmi-chip-id=320'
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1
Tested-on: QCA6174 HW3.2 WLAN.RM.4.4.1-00157-QCARMSWPZ-1
Signed-off-by: Abhishek Kumar <kuabhs@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201207231824.v3.1.Ia6b95087ca566f77423f3802a78b946f7b593ff5@changeid
HE operation IE in beacons is constructed based on userspace params,
which firmware might not be aware of. This causes firmware not to
configure TXOP duration based RTS threshold which could cause mismatch
in behaviour with respect to what is being advertised in beacons. This
patch sends HE operation IE fetched from beacon to firmware using
WMI interface for configuration.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020183111.25458-4-pradeepc@codeaurora.org
QMI sequence fails if caldata file is not available.
It is observed that 'rmmod ath11k' fails if qmi message fails.
With this patch rmmod/insmod is working.
Logs:
Direct firmware load for IPQ8074/caldata.bin failed with error -2
Falling back to user helper
qmi failed to load CAL: IPQ8074/caldata.bin
qmi failed to load board data file:-11
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01699-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606916215-24643-1-git-send-email-akolli@codeaurora.org
I am trying to get the ath11k driver to work with VyOS and during the
build it tries to discover the firmware blobs which drivers require.
This doesn't work with ath11k because it doesn't use the MODULE_FIRMWARE
macro. This patch fixes that.
Signed-off-by: Devin Bayer <dev@doubly.so>
[kvalo@codeaurora.org: cleanup commit log, move to pci.c]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201202182705.dhkml4nb4rf2vwav@orac
Incase of hardware encryption, WMI_PEER_AUTH flag will be set by firmware
during install key. Since install key wont be done for software encryption
mode, firmware will not set this flag. Due to this, seeing traffic failure
in software encryption. Hence, avoid resetting peer auth flag if hardware
encryption disabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01421-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606369414-25211-1-git-send-email-seevalam@codeaurora.org
cppcheck possible warnings: (new ones prefixed by >>, may not real problems)
drivers/net/wireless/ath/ath10k/sdio.c:2234:2:
warning: Non-boolean value returned from function returning bool [returnNonBoolInBooleanFunction]
return param & HI_OPTION_SDIO_CRASH_DUMP_ENHANCEMENT_FW;
Reported-by: kernel test robot <rong.a.chen@intel.com>
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606103240-9868-1-git-send-email-wgong@codeaurora.org
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ath.git patches for v5.11. Major changes:
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
This commit updates the BMPS exit path to be consistent with downstream in
terms of exiting BMPS mode. Downstream sets the flag to send a NULL data
frame to the host on exiting BMPS.
This will tell the AP to send any queued frames to the STA immediately.
Verified the relevant bit toggle in wireshark.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201120021403.2646574-2-bryan.odonoghue@linaro.org
The wmi service available event has been
extended to contain extra 128 bit for new services
to be indicated by firmware.
Currently the presence of any optional TLVs in
the wmi service available event leads to a parsing
error with the below error message:
ath10k_snoc 18800000.wifi: failed to parse svc_avail tlv: -71
The wmi service available event parsing should
not return error for the newly added optional TLV.
Fix this parsing for service available event message.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00720-QCAHLSWMTPL-1
Fixes: cea19a6ce8 ("ath10k: add WMI_SERVICE_AVAILABLE_EVENT support")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605501291-23040-1-git-send-email-pillair@codeaurora.org
It was observed that the codepath for the ATH11K_SKB_HW_80211_ENCAP was
used even when the IEEE80211_TX_CTRL_HW_80211_ENCAP was not enabled for a
an skbuff. This became even more prominent when the QCAs wlan-open patchset
for ath11k [1] was applied and a sane looking fix just caused crashes when
injecting frames via a monitor interface (for example with ratechecker):
[ 86.963152] Unable to handle kernel NULL pointer dereference at virtual address 00000338
[ 86.963192] pgd = ffffffc0008f0000
[ 86.971034] [00000338] *pgd=0000000051706003, *pud=0000000051706003, *pmd=0000000051707003, *pte=00e800000b000707
[ 86.984292] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[...]
[ 87.713339] [<ffffffbffc802480>] ieee80211_tx_status_8023+0xf8/0x220 [mac80211]
[ 87.715654] [<ffffffbffc98bad4>] ath11k_dp_tx_completion_handler+0x42c/0xa10 [ath11k]
[ 87.722924] [<ffffffbffc989190>] ath11k_dp_service_srng+0x70/0x3c8 [ath11k]
[ 87.730831] [<ffffffbffca03460>] 0xffffffbffca03460
[ 87.737599] [<ffffffc00046ef58>] net_rx_action+0xf8/0x288
[ 87.742462] [<ffffffc000097554>] __do_softirq+0xfc/0x220
[ 87.748014] [<ffffffc000097900>] irq_exit+0x98/0xe8
[ 87.753396] [<ffffffc0000cf188>] __handle_domain_irq+0x90/0xb8
[ 87.757999] [<ffffffc000081ca4>] gic_handle_irq+0x6c/0xc8
[ 87.763899] Exception stack(0xffffffc00081bdc0 to 0xffffffc00081bef0)
Problem is that the state of ath11k_skb_cb->flags must be considered
unknown and could contain anything when it is not manually initialized. So
it could also contain ATH11K_SKB_HW_80211_ENCAP. And this can result in the
code to assume that the ath11k_skb_cb->vif is set - even when this is not
always the case for non ATH11K_SKB_HW_80211_ENCAP transmissions.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
[1] https://source.codeaurora.org/quic/qsdk/oss/system/feeds/wlan-open/tree/mac80211/patches?h=NHSS.QSDK.11.4.r3
(162 patches at the moment which are often not upstreamed but essential
to get ath11k working)
Fixes: e7f33e0c52 ("ath11k: add tx hw 802.11 encapsulation offloading support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-2-sven@narfation.org
The driver_data area of ieee80211_tx_info is used in ath11k for
ath11k_skb_cb. The first function in the TX patch which rewrites it to
ath11k_skb_cb is already ath11k_mac_op_tx. No one else in the code path
must use it for something else before it reinitializes it. Otherwise the
data has to be considered uninitialized or corrupt.
But the ieee80211_tx_info.control shares exactly the same area as
ieee80211_tx_info.driver_data and ath11k is still using it. This results in
best case in a
ath11k c000000.wifi1: no vif found for mgmt frame, flags 0x0
or (slightly worse) in a kernel oops.
Instead, the interesting data must be moved first into the ath11k_skb_cb
and ieee80211_tx_info.control must then not be used anymore.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-1-sven@narfation.org
