This patch adds supports for setting VF trust by host. If specified
VF is trusted, then it can enable promisc(include allmulti mode).
If a trusted VF enabled promisc, and being untrusted, host will
disable promisc mode for this VF.
For VF will update its promisc mode from set_rx_mode now, so it's
unnecessary to set broadcst promisc mode when initialization or
reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds support for spoof check configuration for VFs.
When it is enabled, "spoof checking" is done for both mac address
and VLAN. For each VF, the HW ensures that the source MAC address
(or VLAN) of every outgoing packet exists in the MAC-list (or
VLAN-list) configured for RX filtering for that VF. If not,
the packet is dropped.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds support to configure VF link properties.
The options are auto, enable, and disable. Even if the PF
is down, the communication between VFs will be normal
if the VFs are set to enable. The commands are as follows:
'ip link set <pf> vf <vf_id> state <auto|enable|disable>'
change the VF status
'ip link show'
show the setting status
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Don't populate the array tick_array on the stack but instead make it
static. Makes the object code smaller by 29 bytes.
Before:
text data bss dec hex filename
19191 432 0 19623 4ca7 hisilicon/hns3/hns3pf/hclge_tm.o
After:
text data bss dec hex filename
19098 496 0 19594 4c8a hisilicon/hns3/hns3pf/hclge_tm.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the arrays port_map and sl_map on the stack but
instead make them static. Makes the object code smaller by 64 bytes.
Before:
text data bss dec hex filename
49575 6872 64 56511 dcbf hisilicon/hns/hns_dsaf_main.o
After:
text data bss dec hex filename
49350 7032 64 56446 dc7e hisilicon/hns/hns_dsaf_main.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function mdio_sc_cfg_reg_write(), variable "reg_value" could be
uninitialized if regmap_read() fails. However, "reg_value" is used
to decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "priv->phy_mode" variable is an enum and in this context GCC will
treat it as unsigned to the error handling will never trigger.
Fixes: 57c5bc9ad7 ("net: hisilicon: add hix5hd2 mac driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
There is a spelling mistake in a .msg literal string. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds more information for reset DFX. Also, adds some
cleanups to reset info, move reset_fail_cnt into struct
hclge_rst_stats, and modifies some print formats.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch checks ops->set_default_reset_request whether is NULL
before using it in function hns3_slot_reset.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pfc_en and pfc_map need to be displayed in hexadecimal notation,
printing dma address should use %pad, and the end of printed string
needs to be add "\n".
This patch modifies them.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hardware doesn't support use specified speed and duplex
to negotiate, it's unnecessary to check and modify the port
speed and duplex for fibre port when autoneg is on.
Fixes: 22f48e24a2 ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when hns3 driver configures the tm shaper to limit
bandwidth below 20Mbit using the parameters calculated by
hclge_shaper_para_calc(), the actual bandwidth limited by tm
hardware module is not accurate enough, for example, 1.28 Mbit
when the user is configuring 1 Mbit.
This patch adjusts the ir_calc to be closer to ir, and
always calculate the ir_b parameter when user is configuring
a small bandwidth. Also, removes an unnecessary parenthesis
when calculating denominator.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After setting new channel num, it needs free old ring memory and
allocate new ring memory. If there is no enough memory and allocate
new ring memory fail, the ring may initialize fail. To make sure
the network interface can work normally, driver should revert the
channel to the old configuration.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ethtool_ops.set_channels support for HNS3 VF driver,
and updates related TQP information and RSS information, to support
modification of VF TQP number, and uses current rss_size instead of
max_rss_size to initialize RSS.
Also, fixes a format error in hclgevf_get_rss().
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array spec_opcode on the stack but instead make it
static const. Makes the object code smaller by 48 bytes.
Before:
text data bss dec hex filename
6914 1040 128 8082 1f92 hns3/hns3vf/hclgevf_cmd.o
After:
text data bss dec hex filename
6866 1040 128 8034 1f62 hns3/hns3vf/hclgevf_cmd.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_dbg_get_m7_info is used only in the hclge_debugfs.c,
so it should be declared with static.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the selftest and reset are performed at the same time, the loopback
setting may be still in the enable state after the reset. As a result,
packets cannot be sent out.
This patch fixes this issue by disabling loopback in hclge_mac_init.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relational and logical operators evaluate to bool,
explicit conversion is overly verbose and unnecessary.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver can only unregister client which included in hnae3_client_list.
This patch adds the client node validity judgment.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hclge_get_reset_level may return HNAE3_NONE_RESET,
so hdev->reset_level can not be assigned with the return
value in the hclge_reset(), otherwise, it will cause
the use of hdev->reset_level in hclge_reset_event get
into error.
Fixes: 012fcb52f6 ("net: hns3: activate reset timer when calling reset_event")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, the VF index used incorrectly in function
hclge_set_vlan_rx_offload_cfg() and hclge_set_vlan_rx_offload_cfg().
When VF id is greater than 8, for example 9, it will set the
same bit with VF id 1.
This patch fixes it by using vport->vport_id % HCLGE_VF_NUM_PER_CMD /
HCLGE_VF_NUM_PER_BYTE as the array index, instead of vport->vport_id /
HCLGE_VF_NUM_PER_CMD.
Fixes: 052ece6dc1 ("net: hns3: add ethtool related offload command")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the static keyword to the front of declaration of g_dsaf_mode_match,
and resolve the following compiler warning that can be seen when building
with warnings enabled (W=1):
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:27:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function 'hclge_restore_vlan_table':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:8016:18: warning:
variable 'qos' set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 70a214903d ("net: hns3: reduce the parameters of some functions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer reg_info is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current loopback mode is to add 0x1F to the SMAC address
as the DMAC address and enable the promiscuous mode.
However, if the VF address is the same as the DMAC address,
the loopback test fails.
Loopback can be enabled in three places: SSU, MAC, and serdes.
By default, SSU loopback is enabled, so if the SMAC and the DMAC
are the same, the packets are looped back in the SSU. If SSU loopback
is disabled, packets can reach MAC even if SMAC is the same as DMAC.
Therefore, this patch disables the SSU loopback before the loopback
test. In this way, the SMAC and DMAC can be the same, and the
promiscuous mode does not need to be enabled. And this is not
valid in version 0x20.
This patch also uses a macro to replace 0x1F.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the reset interrupt will be cleared firstly, so when
reset fails, if interrupt status register has reset interrupt,
it means there is a new coming reset.
Fixes: 72e2fb0799 ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the loopback test supports only mac selftest and serdes
selftest. This patch adds phy selftest.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware or IMP get specified error it may need the client
to take some special operations.
This patch implements the hns3 client's process_hw_errorx.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimizes the waiting time for TQP reset.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some incorrect type in assignment reported by sparse.
Those sparse warning as below:
- warning : restricted __le16 degrades to integer
- warning : cast from restricted __le32
- warning : expected restricted __le32
- warning : cast from restricted __be32
- warning : cast from restricted __be16
- warning : cast to restricted __le16
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hclge_dcb.c, these pair of codes:
hclge_notify_client(hdev, HNAE3_DOWN_CLIENT);
hclge_notify_client(hdev, HNAE3_UNINIT_CLIENT);
and
hclge_notify_client(hdev, HNAE3_INIT_CLIENT);
hclge_notify_client(hdev, HNAE3_UP_CLIENT);
are called many times, so make them into a function.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To better identify abnormal conditions, this patch modifies or
adds some logs to show driver status more accurately.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies parameters of some functions by deleting
unused parameter.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces kstrtouint()'s patameter base with 0 in the
hclge_dbg_dump_tm_mac(), which makes it more flexible. Also
uses a macro to replace string "dump tm map", since it has been
used multiple times.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses macro to replace some magic number.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For making the code more readable, this patch uses a array to
keep the information about the dumping register, and then uses
it to parse the parameter cmd_buf which passing into
hclge_dbg_dump_reg_cmd().
Also replaces parameter "base" of kstrtouint with 0 in the
hclge_dbg_dump_reg_common(), which makes it more flexible.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:542:30:
warning: meta_data_key_info defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:553:30:
warning: tuple_key_info defined but not used [-Wunused-const-variable=]
The two variable is only used in hclge_main.c,
so just move the definition over there.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the call to phy_attached_info() to the hns driver
to identify which exact PHY drivers is in use.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the call to phy_attached_info() to the hns3 driver
to identify which exact PHY drivers and models is in use.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC TNL interrupt is used to collect statistic info about
link status changing suddenly when netdev is running.
But when stopping netdev, the enabled MAC TNL interrupt is
unnecessary, and may add some noises to the statistic info.
So this patch disables it before stopping MAC.
Fixes: a63457878b ("net: hns3: Add handling of MAC tunnel interruption")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes print level of RAS error log from warning to error.
Because RAS error and its recovery process could cause application
failure. Also uses %u instead of %d when the parameter is unsigned.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer type parameter should be declare as const for preventing
from its pointed value being unexpected modified.
The uninitialized variable can not be return directly. The default
return value is 0 if no abnormal result.
This patch fixes the preceding two errors, deletes redundant
declaration of a function and align one parameter.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some temporary variables do not need to be initialized that
they will be set before used, so this patch deletes the
initialization value of these temporary variables.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huzhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To explain some code, this patch adds some comments, and modifies or
merges some comments to make them more neat.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:3190:5:
warning: symbol 'hclge_func_reset_sync_vf' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro arguments should be enclosed in parentheses, in case of
expression argument, but parentheses of pure number in macro
definition should be removed for simplicity.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before PF asserting function reset, it should make sure
that all its VFs have been ready, otherwise, it will cause
some hardware errors.
So this patch adds function hclge_func_reset_sync_vf() to
synchronize VF before asserting PF function reset. For new
firmware which supports command HCLGE_OPC_QUERY_VF_RST_RDY,
we will try to query VFs' ready status within 30 seconds.
And keep the old implementation for compatible with firmware
which does not support this command.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refines the interface for querying MAC pause
statistics, and adds structure hns3_mac_stats to keep the
count of TX & RX.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a new function hclge_ncl_config_data_print()
to print the data of NCL_CONFIG, to make the code more
readable. Also, using macro replaces some magic number.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware supports up to 8 TX BD for non-TSO skb and 63 TX
BD for TSO skb. Currently hns3 driver does not check the max
BD num that required by a skb before filling desc, which may
cause the hardware to issue a RAS error throug PCIe AER.
This patch adds the max BD num check before filling desc,
if the bd num is not within the hardware limit, it will
record the error by ring->stats.sw_err_cnt counter and
free the skb.
This patch also cleans up the hns3_nic_bd_num function by
changing the return type and removing an unnecessary check.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds tx_vlan_err, tx_l4_proto_err, tx_l2l3l4_err
and tx_tso_err counter to tx process, in order to better
debug the desc filling error.
This patch also adds a missing u64_stats_update_* around
ring->stats.sw_err_cnt and adds hns3_rl_err to limit the
error printing in the IO patch.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we can use ethtool -d command to dump some registers. However,
these registers information is not enough to find out where the problem is.
This patch adds DFX registers information after original registers
when use ethtool -d commmand to dump registers. Also, using macro
replaces some related magic number.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the pause options of HNS3 shown like this:
"RX/TX" is always the same with "RX negotiated/TX negotiated".
Because of the driver covered the value of "RX/TX" with the value
of "RX negotiated/TX negotiated" after adjust link.
This patch records the pause configurations of the user, and never
covered them in adjust link.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the input length reaches the maximum value of size_t, the reverse is
triggered when 1 is added. In addition, there is no need to have such a
large length. Therefore, the input length should be checked and the value
should be less than or equal to 1024.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the hns3_fill_desc_vtags function
by avoiding passing too many parameters, reducing indent
level and some other clean up.
This patch also adds the hns3_fill_skb_desc function to
fill the first desc of a skb.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VF driver has two kinds of interrupts, reset & CMDQ RX.
For revision 0x21, according to the UM, each interrupt should be
cleared by write 0 to the corresponding bit, but the implementation
writes 0 to the whole register in fact, it will clear other
interrupt at the same time, then the VF will loss the interrupt.
But for revision 0x20, this interrupt clear register is a read &
write register, for compatible, we just keep the old implementation
for 0x20.
This patch fixes it, also, adds a new register for reading the interrupt
status according to hardware user manual.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: b90fcc5bd9 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the arm64 platform, executing "ifconfig eth0 up" will fail,
returning "ifconfig: SIOCSIFFLAGS: Input/output error."
ndev->dev is not initialized, dma_map_single->get_dma_ops->
dummy_dma_ops->__dummy_map_page will return DMA_ERROR_CODE
directly, so when we use dma_map_single, the first parameter
is to use the device of platform_device.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_DESC_NUM is 256, in tx_count, the maximum value of
mod(TX_DESC_NUM - 1) is 254, the variable "count" in
the hip04_mac_start_xmit function is never equal to
(TX_DESC_NUM - 1), so hip04_mac_start_xmit never
return NETDEV_TX_BUSY.
tx_count is modified to mod(TX_DESC_NUM) so that
the maximum value of tx_count can reach
(TX_DESC_NUM - 1), then hip04_mac_start_xmit can reurn
NETDEV_TX_BUSY.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling hclge_reset_event() within HCLGE_RESET_INTERVAL,
it returns directly now. If no one call it again, then the
error which needs a reset to fix it can not be fixed.
So this patch activates the reset timer for this case, and
adds checking in the end of the reset procedure to make this
error fixed earlier.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the reset interrupt is cleared in the reset task, which
is too late. Since, when the hardware finish the previous reset,
it can begin to do a new global/IMP reset, if this new coming reset
type is same as the previous one, the driver will clear them together,
then driver can not get that there is another reset, but the hardware
still wait for the driver to deal with the second one.
So this patch clears PF's reset interrupt status in the
hclge_irq_handle(), the hardware waits for handshaking from
driver before doing reset, so the driver and hardware deal with reset
one by one.
BTW, when VF doing global/IMP reset, it reads PF's reset interrupt
register to get that whether PF driver's re-initialization is done,
since VF's re-initialization should be done after PF's. So we add
a new command and a register bit to do that. When VF receive reset
interrupt, it sets up this bit, and PF finishes re-initialization
send command to clear this bit, then VF do re-initialization.
Fixes: 4ed340ab8f ("net: hns3: Add reset process in hclge_main")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver sets handshake status to tell the hardware
that the driver have downed the netdev and it can continue with
reset process. The driver will clear the handshake status when
re-initializing the CMDQ, and does not recover this status
when reset fail, which may cause the hardware to wait for
the handshake status to be set and not being able to continue
with reset process.
So this patch delays clearing handshake status just before UP,
and recovers this status when reset fail.
BTW, this patch adds a new function hclge(vf)_reset_handshake() to
deal with the reset handshake issue, and renames
HCLGE(VF)_NIC_CMQ_ENABLE to HCLGE(VF)_NIC_SW_RST_RDY which
represents this register bit more accurately.
Fixes: ada13ee3db ("net: hns3: add handshake with hardware while doing reset")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The member 'mac_add' defined in hclge_mac_ethertype_idx_rd_cmd
means MAC address, so 'mac_addr' is a better name for it.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 4th and 5th parameter of hclge_cmd_query_error is useless, so this
patch removes them.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclge_tm_schd_info_update calls hclge_tm_schd_info_init to
initialize the schedule info, hdev->tm_info.num_pg and
hdev->tx_sch_mode is not changed, which makes the checking in
hclge_tm_schd_info_init unnecessary.
So this patch moves the hdev->tm_info.num_pg and hdev->tx_sch_mode
checking into hclge_tm_schd_init and changes the return type of
hclge_tm_schd_info_init from int to void.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unused_count variable is used to indicate how many
RX BD need attaching new buffer in hns3_clean_rx_ring,
and the clean_count variable has the similar meaning.
This patch removes the clean_count variable and use
unused_count to uniformly indicate the RX BD that need
attaching new buffer.
This patch also clean up some coding style related to
variable assignment in hns3_clean_rx_ring.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local variable return_status in hclge_get_mac_val_cmd_status()
is useless. So this patch returns the error code directly, instead of
using this variable. Also, replace some '%d' with '%u' in
hclge_get_mac_val_cmd_status().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, when changing the ring parameters, we free the old
ring resources firstly, and then setup the new ring resources.
In some case of an memory allocation fail, there will be no
resources to use. This patch refines it by setup new ring
resources and free the old ring resources in order.
Also reduce the max ring BD number to 32760 according to UM.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some commands are not supported on DCB-unsupported ports.
This patch distinguishes these commands and does not query
unsupported commands in debugfs.
This patch also fix an error in the dump "qos buf cfg"
command in debugfs.
Fixes: 2849d4e7a1 ("net: hns3: Add "tc config" info query function")
Fixes: 7d9d7f8864 ("net: hns3: Add "qos buffer" config info query function")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NCSI has HW error, the IMP will report this error to the driver
by sending a mailbox. After received this message, the driver should
assert a global reset to fix this kind of HW error.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, PF updates link status per second. For some scenario,
it requires link down event being reported more quickly.
To solve it, firmware pushes the link change event to PF with
CMDQ message, and driver updates the link status directly.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to match the firmware node handle of a device and provide
wrappers for {bus/class/driver}_find_device() APIs to avoid proliferation
of duplicate custom match functions.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-usb@vger.kernel.org
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Joe Perches <joe@perches.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190723221838.12024-4-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages when driver
initialization done, so switch to dev_info().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware supports 0.5K, 1K, 2K, 4K RX buffer size, the
RX buffer can not be reused because the hns3_page_order
return 0 when page size and RX buffer size are both 4096.
So this patch changes the hns3_page_order to return 1 when
RX buffer is greater than half of the page size and page size
is less the 8192, and dev_alloc_pages has already been used
to allocate the compound page for RX buffer.
This patch also changes hnae3_* to hns3_* for page order
and RX buffer size calculation because they are used in
hns3 module.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The misc interrupt is used to schedule the reset and mailbox
subtask, and service_task delayed_work is used to do periodic
management work each second.
This patch sets the above three subtask's affinity using the
misc interrupt' affinity.
Also this patch setups a affinity notify for misc interrupt to
allow user to change the above three subtask's affinity.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use delayed work instead of using timers to trigger the
hclge_serive.
Simplify the code with one less middle function and in order
to support misc irq affinity.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some times just see the eth interface have been down/up via
dmesg, but can not know why the eth down. So adds some debug
messages to identify the cause for this.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies firmware version display format in
hclge(vf)_cmd_init() and hns3_get_drvinfo(). Also, adds
some optimizations for firmware version display format.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating memory, the GFP_KERNEL cannot be used during the
spin_lock period. This is because it may cause scheduling when holding
spin_lock. This patch changes GFP flag to GFP_ATOMIC in this case.
Fixes: dd74f815dd ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: lipeng 00277521 <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, hclge_reset_err_handle() will assert a global reset
when the failing count is smaller than MAX_RESET_FAIL_CNT, which
will affect other running functions.
So this patch removes this upgrading, and uses re-scheduling reset
task to do it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some cases, ops->get_reset_level may not be implemented, so we
should check whether it is NULL before calling get_reset_level.
Signed-off-by: Guangbin Huang <huangguangbin@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_set_channels() should check the resetting status firstly,
since the device will reinitialize when resetting. If the
reset has not completed, the hns3_set_channels() may access
invalid memory.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit(net: phy: marvell: change default m88e1510 LED configuration),
the active LED of Hip07 devices is always off, because Hip07 just
use 2 LEDs.
This patch adds a phy_register_fixup_for_uid() for m88e1510 to
correct the LED configuration.
Fixes: 077772468e ("net: phy: marvell: change default m88e1510 LED configuration")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: linyunsheng <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All constant in 'enum HCLGE_MBX_OPCODE' start with HCLGE, except
'HLCGE_MBX_PUSH_VLAN_INFO' (C and L switched)
s/HLC/HCL/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix excessive stack usage in cxgb4, from Arnd Bergmann.
2) Missing skb queue lock init in tipc, from Chris Packham.
3) Fix some regressions in ipv6 flow label handling, from Eric Dumazet.
4) Elide flow dissection of local packets in FIB rules, from Petar
Penkov.
5) Fix TLS support build failure in mlx5, from Tariq Toukab.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ppp: mppe: Revert "ppp: mppe: Add softdep to arc4"
net: dsa: qca8k: replace legacy gpio include
net: hisilicon: Use devm_platform_ioremap_resource
cxgb4: reduce kernel stack usage in cudbg_collect_mem_region()
tipc: ensure head->lock is initialised
tc-tests: updated skbedit tests
nfp: flower: ensure ip protocol is specified for L4 matches
nfp: flower: fix ethernet check on match fields
net/mlx5e: Provide cb_list pointer when setting up tc block on rep
net: phy: make exported variables non-static
net: sched: Fix NULL-pointer dereference in tc_indr_block_ing_cmd()
davinci_cpdma: don't cast dma_addr_t to pointer
net: openvswitch: do not update max_headroom if new headroom is equal to old headroom
net/mlx5e: Convert single case statement switch statements into if statements
net/mlx5: E-Switch, Reduce ingress acl modify metadata stack usage
net/mlx5e: Fix unused variable warning when CONFIG_MLX5_ESWITCH is off
net/mlx5e: Fix compilation error in TLS code
ipv6: fix static key imbalance in fl_create()
ipv6: fix potential crash in ip6_datagram_dst_update()
ipv6: tcp: fix flowlabels reflection for RST packets
...
Use devm_platform_ioremap_resource instead of
devm_ioremap_resource. Make the code simpler.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
HI13X1 changed the offsets and bitmaps for tx_desc
registers in the same peripheral device on different
models of the hip04_eth.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1 changed the offsets and bitmaps for rx_desc
registers in the same peripheral device on different
models of the hip04_eth.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buf unit size of HI13X1_GMAC is cache_line_size,
which is 64, so the address we write to the buf register
needs to be shifted right by 6 bits.
The 31st bit of the PPE_CFG_CPU_ADD_ADDR register
of HI13X1_GMAC indicates whether to release the buffer
of the message, and the low indicates that it is valid.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, group is the same as the port, but some
boards specify a special group for better load
balancing of each processing unit.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1_GMAC delete request for soft reset at first,
otherwise, the subsequent initialization will not
take effect.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1_GMAC changed the offsets and bitmaps for
GE_TX_LOCAL_PAGE_REG registers in the same peripheral
device on different models of the hip04_eth. With the
default configuration, HI13X1_GMAC can also work without
any writes to the GE_TX_LOCAL_PAGE_REG register.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warning from sparse:
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warning from sparse:
hip04_eth.c:468:25: warning: incorrect type in assignment
hip04_eth.c:468:25: expected unsigned int [usertype] send_addr
hip04_eth.c:468:25: got restricted __be32 [usertype]
hip04_eth.c:469:25: warning: incorrect type in assignment
hip04_eth.c:469:25: expected unsigned int [usertype] send_size
hip04_eth.c:469:25: got restricted __be32 [usertype]
hip04_eth.c:470:19: warning: incorrect type in assignment
hip04_eth.c:470:19: expected unsigned int [usertype] cfg
hip04_eth.c:470:19: got restricted __be32 [usertype]
hip04_eth.c:472:23: warning: incorrect type in assignment
hip04_eth.c:472:23: expected unsigned int [usertype] wb_addr
hip04_eth.c:472:23: got restricted __be32 [usertype]
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the hip04_eth driver to support HI13X1_GMAC.
Enable it with CONFIG_HI13X1_GMAC option.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If HCLGE_MBX_MAX_RESP_DATA_SIZE > HCLGE_MBX_MAX_RESP_DATA_SIZE,
the memcpy will cause out of memory. So this patch just set
resp_data_len to the maximum length for this case.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some bitwise operator used signed type, this patch fixes
them with unsigned type.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds default value for tc_size and tc_offset, or it may
get random value and used later.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of msg_data may be NULL in some cases, which will cause
errors reported by some compiler.
So this patch adds a check to fix it.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of param type is always not changed in
hclgevf_bind_ring_to_vector, move the assignment to
front of "for {}" can reduce the redundant assignment.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the HNS3 driver just defines part of IMP return code,
This patch supplements all the remaining IMP return code, and adds
a function to convert this code to the error number.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver queries the media port information, and
updates the port capability periodically. But it sets an error
mac->speed_type value, which stops update port capability.
Fixes: 88d10bd6f7 ("net: hns3: add support for multiple media type")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control autoneg is unsupported for fibre port. It takes no
effect for flow control when restart autoneg. This patch fixes
it, return -EOPNOTSUPP when user tries to enable flow control
autoneg.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, the broadcast promisc is enabled by firmware,
it's unnecessary to enable it when initializing VF.
For revision 0x21, it's necessary to enable broadcast promisc mode
when initializing or re-initializing VF, otherwise, it will be
unable to send and receive promisc packets.
Fixes: f01f5559ca ("net: hns3: don't allow vf to enable promisc mode")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hip07 chip support vlan TSO, this patch adds NETIF_F_TSO
and NETIF_F_TSO6 flags to vlan_features to improve the
performance after adding vlan to the net ports.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CMDQ ring is full, hclge_cmd_send may return directly, but IMP still
working and HW pointer changed, SW ring pointer do not match the HW
pointer. This patch update the SW pointer every time when the space is
full, so it can work normally next time if IMP and HW still working.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNS3_RXD_VLD_B bit has already been checked in hns3_add_frag
or hns3_handle_rx_bd before calling hns3_handle_bdinfo, so when
hns3_handle_bdinfo is called, the HNS3_RXD_VLD_B bit is always
set, which makes the checking in hns3_handle_bdinfo unnecessary.
This patch removes the RXD_VLD_B checking in hns3_handle_bdinfo.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unused linkmode definition.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The frame column is based on rx_crc_errors and rx_frame_errors. So
l3l4 checksum error should not be counted by rx_crc_errors. Instead,
l3l4 checksum error should be counted in ifconfig error column.
Fixes: d3ec4ef669 ("net: hns3: refactor the statistics updating for netdev")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since some MSI-X interrupt's status may be cleared by hardware,
so when the driver receives the interrupt, reading
HCLGE_VECTOR0_PF_OTHER_INT_STS_REG register will get an empty
unknown interrupt. For this case, the irq handler should enable
vector0 interrupt. This patch also use dev_info() instead of
dev_dbg() in the hclge_check_event_cause(), since this information
will be useful for normal usage.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF reset may fail for some probabilistic reasons,
such as wait for hardware reset timeout, wait for mailbox
response timeout, so this patch tries to re-schedule the
reset task when the number of reset failing is under
HCLGEVF_RESET_MAX_FAIL_CNT. This patch also add a function
hclgevf_reset_err_handle() to handle the reset failing.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Local device and link partner config auto-negotiation on both,
local device config pause frame use as: rx on/tx off,
link partner config pause frame use as: rx off/tx on.
We except the result is:
Local device:
Autonegotiate: on
RX: on
TX: off
RX negotiated: on
TX negotiated: off
Link partner:
Autonegotiate: on
RX: off
TX: on
RX negotiated: off
TX negotiated: on
But actually, the result of Local device and link partner is both:
Autonegotiate: on
RX: off
TX: off
RX negotiated: off
TX negotiated: off
The root cause is that the supported flag is has only Pause,
reference to the function genphy_config_advert():
static int genphy_config_advert(struct phy_device *phydev)
{
...
linkmode_and(phydev->advertising, phydev->advertising,
phydev->supported);
...
}
The pause frame use of link partner is rx off/tx on, so its
advertising only set the bit Asym_Pause, and the supported is
only set the bit Pause, so the result of linkmode_and(), is
rx off/tx off.
This patch adds Asym_Pause to the supported flag to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting -Wformat=2, there is a compiler warning like this:
hclge_main.c:xxx:x: warning: format not a string literal and no
format arguments [-Wformat-nonliteral]
strs[i].desc);
^~~~
This patch adds missing format parameter "%s" to snprintf() to
fix it.
Fixes: 46a3df9f97 ("Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hdev->tx_sch_mode is HCLGE_FLAG_VNET_BASE_SCH_MODE, the
hclge_tm_schd_mode_vnet_base_cfg calls hclge_tm_pri_schd_mode_cfg
with vport->vport_id as pri_id, which is used as index for
hdev->tm_info.tc_info, it will cause out of bound access issue
if vport_id is equal to or larger than HNAE3_MAX_TC.
Also hardware only support maximum speed of HCLGE_ETHER_MAX_RATE.
So this patch adds two checks for above cases.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when there is share buffer in the SSU(storage
switching unit), the low waterline for RX private buffer is
too low to keep the hardware running. Hardware may have
processed all the packet stored in the private buffer of the
low waterline before the new packet comes, because hardware
only tell the peer send packet again when the private buffer
is under the low waterline.
So this patch only allocate RX private buffer if there is
enough buffer according to hardware user manual.
This patch also reserve some buffer for reusing when TC num
is less than or equal to 2, and change PAUSE_TRANS_GAP &
HCLGE_NON_DCB_ADDITIONAL_BUF according to hardware user
manual.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when TC num is one, the DCB will be disabled no matter if
pfc_en is non-zero or not.
This patch enables the DCB if pfc_en is non-zero, even when TC num
is one.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When change MTU or other operations, which just calling .reset_notify
to do HNAE3_DOWN_CLIENT and HNAE3_UP_CLIENT, then
the netdev_tx_reset_queue() in the hns3_clear_all_ring() will be
ignored. So the dev_watchdog() may misdiagnose a TX timeout.
This patch separates netdev_tx_reset_queue() from
hns3_clear_all_ring(), and unifies hns3_clear_all_ring() and
hns3_force_clear_all_ring into one, since they are doing
similar things.
Fixes: 3a30964a2e ("net: hns3: delay ring buffer clearing during reset")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we failed to enable NIC HW error interrupts during client
initialization in some cases, we should do exception handling to clear
flags and free the resources.
Fixes: 00ea6e5fda ("net: hns3: delay and separate enabling of NIC and ROCE HW errors")
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ROCE HW errors should only be enabled when initializing ROCE's
client, the current code enable it no matter initializing NIC or
ROCE client.
So this patch fixes it.
Fixes: 00ea6e5fda ("net: hns3: delay and separate enabling of NIC and ROCE HW errors")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading or unloading module, it should wait for the reset task
done before it un-initializes the client, otherwise the reset task
may cause a NULL pointer reference.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds check to number of bds before we allocate memory for
them. If we get an invalid bd num in some cases, it will cause a memory
overflow.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add override_pci_need_reset to prevent redundant and unwanted PF
resets if a RAS error occurs in commit 69b51bbb03 ("net: hns3: fix
to stop multiple HNS reset due to the AER changes").
Now in HNS3 driver, we use hw_err_reset_req to record reset level that
we need to recover from a RAS error. This variable cans solve above
issue as override_pci_need_reset, so this patch removes
override_pci_need_reset.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users should be informed if HNS driver failed to allocate memory for
descriptor when handling hw errors. This patch solve above issues.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimizes hclge_handle_hw_ras_error() to make the code logic
clearer.
1. If there was no NIC or Roce RAS when we read
HCLGE_RAS_PF_OTHER_INT_STS_REG, we return directly.
2. Because NIC and Roce RAS may occurs at the same time, so we should
check value of revision at first before we handle Roce RAS instead
of only checking it in branch of no NIC RAS is detected.
3. Check HCLGE_STATE_RST_HANDLING each time before we want to return
PCI_ERS_RESULT_NEED_RESET.
4. Remove checking of HCLGE_RAS_REG_NFE_MASK and
HCLGE_RAS_REG_ROCEE_ERR_MASK because if hw_err_reset_req is not
zero, it proves that we have set it in handling of NIC or Roce RAS.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing global reset, the MAC autoneg state of fibre
port is set to default, which may cause user configuration
lost. This patch fixes it by restore the MAC autoneg state
after reset.
Fixes: 22f48e24a2 ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When HW is resetting, firmware is unable to handle commands
from driver. So if remove VLAN device from stack at this time,
it will fail to remove the VLAN ID from HW VLAN filter, then
the VLAN filter status is unsynced with stack.
This patch fixes it by recording the VLAN ID delete failed,
and removes them again when reset complete.
Fixes: 44e626f720 ("net: hns3: fix VLAN offload handle for VLAN inserted by port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For VF VLAN filter is disabled when VF VLAN table is full, then the
new VLAN ID won't be added into VF VLAN table, it will always print
fail log when remove these VLAN IDs. If user has added too many
VLANs, it will cause massive verbose print logs.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing selftest for fibre port with autoneg on, the MAC speed
may be incorrect, which may cause the selftest failed. This patch
fixes it by halting autoneg during the selftest.
Fixes: 22f48e24a2 ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"git diff" says:
\ No newline at end of file
after modifying the file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer ae_dev is null checked however, prior to that it is dereferenced
when assigned pointer ops. Fix this by assigning pointer ops after ae_dev
has been null checked.
Addresses-Coverity: ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does following things:
1. add the keyword const before some variables which won't be modified
in functions.
2. changes some variables from signed to unsigned to avoid bitwise
operation on signed variables.
3. adds or removes initialization of some variables.
4. defines a new structure to help parsing mailbox messages instead of
using an array which is harder to get the meaning of each element.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver may not be able to disable the ring through firmware
when downing the netdev during reset process, which may cause
hardware accessing freed buffer problem.
This patch delays the ring buffer clearing to reset uninit
process because hardware will not access the ring buffer after
hardware reset is completed.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hns3_nic_net_xmit does not return NETDEV_TX_BUSY when doing
a loopback selftest, the skb is not freed in hns3_clean_tx_ring
or hns3_nic_net_xmit, which causes skb not freed problem.
This patch fixes it by freeing skb when hns3_nic_net_xmit does
not return NETDEV_TX_OK.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev is dereferenced before null checking in the function
hns3_setup_tc.
This patch moves the dereferencing after the null checking.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns3_nic_init_irq(), if request irq fail at index i,
the function return directly without releasing irq resources
that already requested, and nowhere else will release them.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IMP will set restting state for all function when PF FLR, driver
just clear the restting state in resetting progress, but don't do
it in initializing progress. As FLR is not created by driver,
it is necessary to clear restting state when initializing HW device.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function hclge_handle_all_hw_msix_error() contains four parts:
1. Query buffer descriptors for MSI-X errors.
2. Query and clear all main PF MSI-X errors.
3. Query and clear all PF MSI-X errors.
4. Handle mac tunnel interrupts.
Part 2 and part 3 handle errors of some different modules respectively,
this patch extracts them into dividual functions, which makes the logic
clearer.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies print message of rx_q_search_miss from error to dfx to
prevent misleading users, because this interrupt may occur if we receive
packets during initialization of HNS3 driver.
Otherwise, this patch masks 28th bit of PPU_MPF_ABNORMAL_SRC2 which is now
meaningless.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the recovery for the HNS H/W errors which occurred
before the driver initialization.
Reported-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presently the HNS driver enables the HNS H/W error interrupts after
the dev initialization is completed. However some exceptions such as
NCSI errors can occur when the network port driver is not loaded
and those errors required reporting to the BMC.
Therefore the firmware enabled all the HNS ras error interrupts
before the driver is loaded. And in some cases, there will be some
H/W errors remained unclear before reboot. Thus the HNS driver needs
to process and recover those hw errors occurred before HNS driver is
initialized.
This patch adds processing of the HNS hw errors(RAS and MSI-X)
which occurred before the driver initialization. For RAS, because
they are enabled by firmware, so we can detect specific bits, then
log and clear them. But for MSI-X which can not be enabled before
open vector0 irq, we can't detect the specific error bits, so we
just write 1 to all interrupt source registers to clear.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS does not need to be reset when errors occur in some bits.
However presently the HNAE3_FUNC_RESET is set in this case and
as a result the default_reset is done when these errors are reported.
This patch fix this issue. Also patch does some optimization
in setting the reset level for the error recovery.
Reported-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presently the error handling code sets the reset level required
for the recovery of the hw errors to the reset framework in the
error_detected AER callback. However the rest_event would be
called later from the slot_reset callback. This can cause issue
of using the wrong reset_level if a high priority reset request
occur before the slot_reset is called.
This patch delays setting of the reset level, required
for the hw errors, to the reset framework until the
slot_reset is called.
Reported-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some coding style issues reported by some static code
analysis tools and code review, such as modify some comments, rename
some variables, log some errors in detail, and fixes some alignment
errors.
BTW, these cleanups do not change the logic of code.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: HuiSong Li <lihuisong@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch deletes some redundant code and refactors some bloated
functions.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make it more readable, this patch modifies PF/VF's
RSS hash key configuring function.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some macros instead of magic numbers in serval places
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to improve readability, this patch uses macros to
replace some magic numbers, and adds some comments for some
others.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since HNAE3_CLIENT_UNIC and HNAE3_DEV_UNIC is not used any more,
this patch removes the redundant codes.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We trigger PF reset when a RAS error of NIC named over_8bd_nfe_err
occurred before. But it is possible that a VF causes that error, it's
reasonable to trigger VF reset instead of PF reset in this case.
This patch add detection of vf_id if a over_8bd_nfe_err occurs, if
vf_id is 0, we trigger PF reset. Otherwise, we will trigger VF reset
on the VF with error.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new hns3_get_new_flow_lvl function to calculate
the packet flow level, which is used to decide the interrupt
coalescence parameter, in order to make the flow level calculation
code more readable and make the future calculation ajdustment easier.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces numa_node_id with numa_mem_id when doing buffer
reusing checking, because the buffer still can be reused when the
buffer is from the nearest node and the local node has no memory
attached.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a GRO packet is assembled by HW, the checksum is
modified to reflect the entire packet by HW and skb->ip_summed is
set to CHECKSUM_UNNECESSARY, which is not compliant with SW GRO.
This patch sets up skb's network and transport header, sets the
GRO packet's checksum according to pseudo header and set the
skb->ip_summed to CHECKSUM_PARTIAL.
This patch also use gso_size to distinguish GRO packet from
normal packet, use eth_type_vlan to check the VLAN type and set
the SKB_GSO_TCP_FIXEDID according to BD info during HW GRO info
processing.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to user manual, the maximum size of mailbox responding
data is 8 bytes, the macro HCLGE_MBX_MAX_RESP_DATA_SIZE
should be defined as 8 instead of 16.
Fixes: 9194d18b05 ("net: hns3: fix the problem that the supported port is empty")
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch logs detail error info of ROCEE ECC and AXI errors for
debug purpose, and remove unnecessary reset for ROCEE overflow
errors.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.
2) Read SFP eeprom in max 16 byte increments to avoid problems with
some SFP modules, from Russell King.
3) Fix UDP socket lookup wrt. VRF, from Tim Beale.
4) Handle route invalidation properly in s390 qeth driver, from Julian
Wiedmann.
5) Memory leak on unload in RDS, from Zhu Yanjun.
6) sctp_process_init leak, from Neil HOrman.
7) Fix fib_rules rule insertion semantic change that broke Android,
from Hangbin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
net: aquantia: fix wol configuration not applied sometimes
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
net: rds: fix memory leak when unload rds_rdma
ipv6: fix the check before getting the cookie in rt6_get_cookie
ipv4: not do cache for local delivery if bc_forwarding is enabled
s390/qeth: handle error when updating TX queue count
s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
s390/qeth: check dst entry before use
s390/qeth: handle limited IPv4 broadcast in L3 TX path
net: fix indirect calls helpers for ptype list hooks.
net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
udp: only choose unbound UDP socket for multicast when not in a VRF
net/tls: replace the sleeping lock around RX resync with a bit lock
...
Remove references to HCLGE_MAC_ETHERTYPE_LLDP and use ETH_P_LLDP instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All RAS and MSI-X should be enabled just in the final stage of HNS3
initialization. It means that they should be enabled in
hclge_init_xxx_client_instance instead of hclge_ae_dev(). Especially
MSI-X, if it is enabled before opening vector0 IRQ, there are some
chances that a MSI-X error will cause failure on initialization of
NIC client instane. So this patch delays enabling of HW errors.
Otherwise, we also separate enabling of ROCE RAS from NIC, because
it's not reasonable to enable ROCE RAS if we even don't have a ROCE
driver.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are four commands being used to query and clear RAS and MSI-X
interrupts status. They should be contained in array of special opcodes
because these commands have several descriptors, and we need to judge
return value in the first descriptor rather than the last one as other
opcodes. In addition, we shouldn't set the NEXT_FLAG of first descriptor.
This patch fixes above issues.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't set HNAE3_NONE_RESET bit of the variable that represents a
reset request during handling of MSI-X errors, or may cause issue when
trigger reset.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LINK_UP and LINK_DOWN are two bits of MAC tunnel interrupts, but previous
HNS3 driver didn't handle them. If they were enabled, value of these two
bits will change during link down and link up, which will cause HNS3
driver keep receiving IRQ but can't handle them.
This patch adds handling of these two bits of interrupts, we will record
and clear them as what we do to other MAC tunnel interrupts.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hclge/hclgevf and hns3 module can be unloaded independently,
when hclge/hclgevf unloaded firstly, the ops of ae_dev should
be set to NULL, otherwise it will cause an use-after-free problem.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we add a VF without loading hclgevf.ko and then there is a RAS error
occurs, PCIe AER will call error_detected and slot_reset of all functions,
and will get a NULL pointer when we check ad_dev->ops->handle_hw_ras_error.
This will cause a call trace and failures on handling of follow-up RAS
errors.
This patch check ae_dev and ad_dev->ops at first to solve above issues.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the port shaper according to the MAC speed as
suggested by hardware user manual.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In orginal codes, the driver only restore VLAN filter entries
for PF after reset, the VLAN entries of VF will lose in this
case.
This patch fixes it by recording VLAN IDs for each function
when add VLAN, and restore the VLAN IDs after reset.
Fixes: 681ec3999b ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF VLAN table can only support no more than 256 VLANs. When user
adds too many VLANs, the VF VLAN table will be full, and firmware
will close the VF VLAN table for the function. When VF VLAN table
is full, and user keeps adding new VLANs, it's unnecessary to
configure the VF VLAN table, because it will always fail, and print
warning message. The worst case is adding 4K VLANs, and doing reset,
it will take much time to restore these VLANs, which may cause VF
reset fail by timeout.
Fixes: 6c251711b3 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since core reset is similar to the global reset, so this
patch removes it and uses global reset to replace it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing a loopback test at copper ports, the serdes loopback
and the phy loopback will fail, because of the adjust link had
not finished, and phy not ready.
Adds sleep between adjust link and test process to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When hclge_bind_ring_with_vector() fails,
hclge_map_unmap_ring_to_vf_vector() returns the error
directly, so nobody will free the memory allocated by
hclge_get_ring_chain_from_mbx().
So hclge_free_vector_ring_chain() should be called no matter
hclge_bind_ring_with_vector() fails or not.
Fixes: 84e095d64e ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_uninit_phy() should be called before checking
HNS3_NIC_STATE_INITED flags, otherwise when this checking fails,
there is nobody to call hns3_uninit_phy().
Fixes: c8a8045b2d ("net: hns3: Fix NULL deref when unloading driver")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unloading driver, the reset task should not be scheduled
anymore. If disable IRQ before cancel ongoing reset task,
the IRQ may be re-enabled by the reset task.
This patch uses HCLGE_STATE_REMOVING/HCLGEVF_STATE_REMOVING
flag to indicate that the driver is unloading, and we should
stop new coming reset service to be scheduled, otherwise,
reset service will access some resource which has been freed
by unloading.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reset happens, the hardware reset should begin after the
driver has finished its preparatory work, otherwise it may cause
some hardware error.
Before Hardware's reset, it will wait for the driver to write
bit HCLGE_NIC_CMQ_ENABLE of register HCLGE_NIC_CSQ_DEPTH_REG
to 1, while the driver finishes its preparatory work will do that.
BTW, since some cases this register will be cleared, so it needs
some sync time before driver's writing.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclgevf_init_client_instance() is a little bloated and there is
some duplicated code. This patch adds some cleanup for it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_init_client_instance() is a little bloated and there is
some duplicated code. This patch adds some cleanup for it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF NIC client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGEVF_STATE_NIC_REGISTERED
to indicate that. And before calling VF NIC client's uninit_instance(),
we clear this state.
So any operation of VF NIC client from HCLGEVF is not allowed if this
state is not set.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PF ROCE client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGE_STATE_ROCE_REGISTERED
to indicate that. And before calling PF ROCE client's uninit_instance(),
we clear this state.
So any operation of the ROCE client from HCLGE is not allowed if this
state is not set.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PF NIC client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGE_STATE_NIC_REGISTERED
to indicate that. And before calling PF NIC client's uninit_instance(),
we clear this state.
So any operation of PF NIC client from HCLGE is not allowed if this
state is not set.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware user menual, the GRO_SIZE is 14 bits width,
the HNS3_RXD_GRO_SIZE_M is 10 bits width now, which may cause
hardware GRO received packet error problem.
Fixes: a6d53b97a2 ("net: hns3: Adds GRO params to SKB for the stack")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ifdef condition of function hclge_add_fd_entry_by_arfs() is
unnecessary. It may cause compile warning when CONFIG_RFS_ACCEL
is not chosen. This patch fixes it by removing the ifdef condition.
Fixes: d93ed94fbe ("net: hns3: add aRFS support for PF")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC capbility may be changed with port speed changes. Driver
needs to read the active FEC mode, and update FEC capability
when port speed changes.
Fixes: 7e6ec9148a ("net: hns3: add support for FEC encoding control")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds aRFS support for PF. The aRFS rules are also
stored in the hardware flow director table, Use the existing
filter management functions to insert TCPv4/UDPv4/TCPv6/UDPv6
flow director filters. To avoid rule conflict, once user adds
flow director rules with ethtool, the aRFS will be disabled,
and clear exist aRFS rules. Once all user configure rules were
removed, aRFS can work again.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be compatible with aRFS rules, this patch adds
spin_lock for flow director rule adding, deleting, querying,
and packages the rule configuration.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate CPU rmap and add entry for each irq. CPU rmap is
used in aRFS to get the queue number of the rx completion
interrupts.
In additional, remove the calling of
irq_set_affinity_notifier() in hns3_nic_init_irq(), because
we have registered notifier in irq_cpu_rmap_add() for each
vector, otherwise it may cause use-after-free issue.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer l2_hdr is being assigned to itself, this is redundant
and can be removed.
Addresses-Coverity: ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses devm_kcalloc instead of kcalloc when allocating
ring->desc_cb, because devm_kcalloc not only ensure to free the
memory when the dev is deallocted, but also allocate the memory
from it's device memory node.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some unused field in struct hns3_enet_ring,
use ring->dev for ring_to_dev macro, and use dev consistently
in hns3_fill_desc.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When page size is 64K, RX buffer is currently not reused when the
page_offset is moved to last buffer. This patch adds checking to
decide whether the buffer page can be reused when last_offset is
moved beyond last offset.
If the driver is the only user of page when page_offset is moved
to beyond last offset, then buffer can be reused and page_offset
is set to zero.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a barrier is used when cleaning each TX BD, which may
cause performance degradation.
This patch optimizes it to use one barrier when cleaning TX BD
each round.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When desc filling fails in hns3_nic_net_xmit, it will call
hns3_clear_desc to unmap the dma mapping. But currently the
ring->next_to_use points to the desc where the desc filling
or dma mapping return error, which means the desc that
ring->next_to_use points to has not done the dma mapping,
the desc that need unmapping is before the ring->next_to_use.
This patch fixes it by calling ring_ptr_move_bw(next_to_use)
before doing unmapping operation, and set desc_cb->dma to
zero to avoid freeing it again when unloading.
Also, when filling skb head or frag fails, both need to unmap
all the way back to next_to_use_head, so remove one desc filling
error handling.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filling len and checksum info to description, there is some
similar checking or calculation.
So this patch adds hns3_set_l2l3l4 to fill the inner(/normal)
header's len and checksum info. If it is a encapsulation skb, it
calls hns3_set_outer_l2l3l4 to handle the outer header's len and
checksum info, in order to avoid some similar checking or
calculation.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch separates the inner and outer l2l3l4 len handling in
hns3_set_l2l3l4_len, this is a preparation to combine the l2l3l4
len and checksum handling for inner and outer header.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware user manual, the tunnel packet type is
available in the rx.ol_info field of struct hns3_desc. Currently
the tunnel packet type is decided by the rx.l234_info, which may
cause RX checksum handling error.
This patch fixes it by using the correct field in struct hns3_desc
to decide the tunnel packet type.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW requires every continuous 8 buffer data to be larger than MSS,
we simplify it by ensuring skb_headlen + the first continuous
7 frags to to be larger than GSO header len + mss, and the
remaining continuous 7 frags to be larger than MSS except the
last 7 frags.
This patch adds hns3_skb_need_linearized to handle it for TSO
case.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, using "ethtool --statistics" can show how many time RX
page have been reused, but there is no counter for RX page not
being reused.
This patch adds non_reuse_pg counter to better debug the performance
issue, because it is hard to determine when the RX page is reused
or not if there is no such counter.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_schedule_irqoff is introduced to be used from hard interrupts
handlers or when irqs are already masked, see:
https://lists.openwall.net/netdev/2014/10/29/2
So this patch replaces napi_schedule with napi_schedule_irqoff.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, maybe_stop_tx ops for TSO and non-TSO case share some BD
calculation code, so this patch unifies the maybe_stop_tx by removing
the maybe_stop_tx ops. skb_is_gso() can be used to differentiate the
case between TSO and non-TSO case if there is need to handle special
case for TSO case.
This patch also add tx_copy field in "ethtool --statistics" to help
better debug the performance issue caused by calling skb_copy.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for FEC encoding control, user can change
FEC mode by command ethtool --set-fec, and get FEC mode by command
ethtool --show-fec. The fec capability is changed follow the port
speed. If autoneg on, the user configure fec mode will be overwritten
by autoneg result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, our driver only supports phydev to autoneg or change
port speed. This patch adds support for fibre port, driver gets
media speed capability and autoneg capability from firmware. If
the media supports multiple speeds, user can change port speed
with command "ethtool -s <devname> speed xxxx autoneg off duplex
full". If autoneg on, the user configuration may be overwritten
by the autoneg result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we can only identify copper and fiber type, the
supported link modes of port information are always showing
SR type. This patch adds support for multiple media types,
include SR, LR CR, KR. Driver needs to query the media type
from firmware periodicly, and updates the port information.
The new port information looks like this:
Settings for eth0:
Supported ports: [ FIBRE ]
Supported link modes: 25000baseCR/Full
25000baseSR/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Supported FEC modes: None BaseR
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000036 (54)
probe link ifdown ifup
Link detected: yes
In order to be compatible with old firmware which only support
sfp speed, we remained using the same query command, and kept
the former logic.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-04-28
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Introduce BPF socket local storage map so that BPF programs can store
private data they associate with a socket (instead of e.g. separate hash
table), from Martin.
2) Add support for bpftool to dump BTF types. This is done through a new
`bpftool btf dump` sub-command, from Andrii.
3) Enable BPF-based flow dissector for skb-less eth_get_headlen() calls which
was currently not supported since skb was used to lookup netns, from Stanislav.
4) Add an opt-in interface for tracepoints to expose a writable context
for attached BPF programs, used here for NBD sockets, from Matt.
5) BPF xadd related arm64 JIT fixes and scalability improvements, from Daniel.
6) Change the skb->protocol for bpf_skb_adjust_room() helper in order to
support tunnels such as sit. Add selftests as well, from Willem.
7) Various smaller misc fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It's meaningless to trigger reset when failed to send command to IMP,
because the failure is usually caused by no authority, illegal command
and so on. When that happened, we just need to return the status code
for further debugging.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check for the hns3_put_ring_config() to prevent
double free, and for more readable, move the NULL assignment of
priv->ring_data into the hns3_put_ring_config().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test results show that the maximum time of hardware return
to mac link state is 500MS.The software needs to set twice the
maximum time of hardware return state (1000MS).
If not modified, the loopback test returns probability failure.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configure pause, current implementation returns directly
after setup PFC without setup BP, which is not sufficient.
So this patch fixes it, only return while setting PFC failed.
Fixes: 44e59e375b ("net: hns3: do not return GE PFC setting err when initializing")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the hardware does not handle mailboxes and the hardware
reset include TQP reset, so it is unnecessary to reset TQP
in the hclgevf_ae_stop() while doing VF reset. Also it is
unnecessary to reset the remaining TQP when one reset fails.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses a reserved byte in the hclge_mbx_vf_to_pf_cmd
to save the need_resp flag, so when PF received the mailbox,
it can use it to decise whether send a response to VF.
For hclge_set_vf_uc_mac_addr(), it should use mbx_need_resp flag
to decide whether send response to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since irq handler and mailbox task will both update arq's count,
so arq's count should use atomic_t instead of u32, otherwise
its value may go wrong finally.
Fixes: 07a0556a3a ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGEVF_STATE_CMD_DISABLE is more suitable than
HCLGEVF_STATE_RST_HANDLING to stop sending keep alive msg,
since HCLGEVF_STATE_RST_HANDLING only be set when the reset
task is running.
Fixes: c59a85c07e ("net: hns3: stop sending keep alive msg to PF when VF is resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bdinfo handled in hns3_handle_bdinfo is only valid on the
last BD of the current packet, currently the bd info may be handled
based on the first BD if the packet has more than two BDs, which
may cause rx error.
This patch fixes it by using the last BD of the current packet in
hns3_handle_bdinfo.
Also, hns3_set_rx_skb_rss_type has used RSS hash value from the last
BD of the current packet, so remove the same last BD calculation in
hns3_set_rx_skb_rss_type and call it from hns3_handle_bdinfo.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_desc_unused() returns how many BD have been cleaned, but new
buffer has not been attached to them. The register of
HNS3_RING_RX_RING_FBDNUM_REG returns how many BD need allocating new
buffer to or need to cleaned. So the remaining BD need to be clean
is HNS3_RING_RX_RING_FBDNUM_REG - hns3_desc_unused().
Also, new buffer can not attach to the pending BD when the last BD is
not handled, because memcpy has not been done on the first pending BD.
This patch fixes by subtracting the pending BD num from unused_count
after 'HNS3_RING_RX_RING_FBDNUM_REG - unused_count' is used to calculate
the BD bum need to be clean.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_clean_tx_ring calls hns3_nic_reclaim_one_desc to clean
buffers and set ring->next_to_clean, then hns3_nic_net_xmit
reuses the cleaned buffers. But there are no memory barriers
when buffers gets recycled, so the recycled buffers can be
corrupted.
This patch uses smp_store_release to update ring->next_to_clean
and smp_load_acquire to read ring->next_to_clean to properly
hand off buffers from hns3_clean_tx_ring to hns3_nic_net_xmit.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default m88e151x LED configuration is 0x1177, used LED[0]
for 1000M link, LED[1] for 100M link, and LED[2] for active.
But for some boards, which use LED[0] for link, and LED[1] for
active, prefer to be 0x1040. To be compatible with this case,
this patch defines a new dev_flag, and set it before connect
phy in HNS3 driver. When phy initializing, using the new
LED configuration if this dev_flag is set.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update all users of eth_get_headlen to pass network device, fetch
network namespace from it and pass it down to the flow dissector.
This commit is a noop until administrator inserts BPF flow dissector
program.
Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
PF supports all debugfs command, but VF only supports part of
debugfs command. So VF should not show unsupported help information.
This patch adds a check for PF and PF to show the supportable help
information.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates VF's TQP statistic info in the service task,
and adds a limitation to prevent update too frequently.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC tnl interruptions are different from other type of RAS and MSI-X
errors, because some bits, such as OVF/LR/RF will occur during link up
and down.
The drivers should clear status of all MAC tnl interruption bits but
shouldn't print any message that would mislead the users.
In case that link down and re-up in a short time because of some reasons,
we record when they occurred, and users can query them by debugfs.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allow users to dump content of NCL_CONFIG by using debugfs
command.
Command format:
echo dump ncl_config <offset> <length> > cmd
It will print as follows:
hns3 0000:7d:00.0: offset | data
hns3 0000:7d:00.0: 0x0000 | 0x00000020
hns3 0000:7d:00.0: 0x0004 | 0x00000400
hns3 0000:7d:00.0: 0x0008 | 0x08020401
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for network interface message level
settings. The message level can be changed by module parameter
or ethtool.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we just print few information when tx timeout happens.
In order to find out the cause of timeout, this patch prints more
information about the packet statistics, tqp registers and
napi state.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function hns3_get_tx_timeo_queue_info(), it should use
netdev->num_tx_queues, instead of netdve->real_num_tx_queues
as the loop limitation.
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current codes, tx_timeout_cnt is used before increased,
then we can see the tx_timeout_count is still 0 from the
print when tx timeout happens, e.g.
"hns3 0000:7d:00.3 eth3: tx_timeout count: 0, queue id: 0, SW_NTU:
0xa6, SW_NTC: 0xa4, HW_HEAD: 0xa4, HW_TAIL: 0xa6, INT: 0x1"
The tx_timeout_cnt should be updated before used.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When wait for response timeout or response code not match, there
should be more information for debugging.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When received vector0 msix and other event interrupt, it should
print the value of the register for debugging.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some statistics for VF reset.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds statistics for PF's reset information,
also, provides a debugfs command to dump these statistics.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting vport->bw_limit to hdev->tm_info.pg_info[0].bw_limit
in hclge_tm_vport_tc_info_update, vport->bw_limit can be as big as
HCLGE_ETHER_MAX_RATE (100000), which can not fit into u16 (65535).
So this patch fixes it by using u32 for vport->bw_limit.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input parameter "proto" in function hclge_set_vlan_filter_hw()
is asked to be __be16, but got u16 when calling it in function
hclge_update_port_base_vlan_cfg().
This patch fixes it by converting it with htons().
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 21e043cd81 ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some redundant BH disable when initializing
and uninitializing command queue.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is pending skb in RX flow when close the port, and the
pending buffer is not cleaned, the new packet will be added to
the pending skb when the port opens again, and the first new
packet has error data.
This patch cleans the pending skb when clean RX ring.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some cases, PHY may not be connected to MDIO bus, then
the driver will initialize fail since MDIO bus initialization
fails.
This patch fixes it by skipping the MDIO bus initialization
when PHY is inexistent.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware description, reset level that should be
triggered are not consistent in a module. For example, in SSU
common errors, the first two bits has no need to do reset,
but the other bits need global reset.
This patch sets separate reset level for all RAS and MSI-X
interrupts by adding a reset_lvel field in struct hclge_hw_error,
and fixes some incorrect reset level.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hardware may have not enough buffer to receive packet
when it has used more than two MPS(maximum packet size) of
buffer, but there are still a lot of shared buffer left unused
when TC num is small.
This patch divides shared buffer to be used between TC when
the port supports DCB, and adjusts the waterline and threshold
according to user manual for the port that does not support
DCB.
This patch also change hclge_get_tc_num's return type to u32
to avoid signed-unsigned mix with divide.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently RX shared buffer' threshold size for speific TC is
set to smaller value when the TC's PFC is not enabled, which may
cause performance problem because hardware may not have enough
hardware buffer when PFC is not enabled.
This patch sets the same threshold size for all TC no matter if
the specific TC's PFC is enabled.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a GRO packet is received by driver, the cwr field in the
struct tcphdr needs to be checked to decide whether to set the
SKB_GSO_TCP_ECN for skb_shinfo(skb)->gso_type.
So this patch adds hns3_gro_complete to do that, and adds the
hns3_handle_bdinfo to handle the hns3_gro_complete and
hns3_rx_checksum.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the parameters of hns3_rx_checksum to be more specific to
what is used internally, rather than passing in a pointer to the
whole hns3_desc. Reduces duplicate code and bring this function
inline with the approach used in hns3_set_gro_param.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.
This patch fixes it. When VF loads up, it firstly queries the port
based VLAN state from PF. When user change port based VLAN state
from PF, PF firstly checks whether the VF is alive. If the VF is
alive, then PF notifies the VF the modification; otherwise PF
configure the port based VLAN state directly.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.
Indeed, ndo_set_vf_vlan() is expected to enable or disable port based
VLAN (hardware inserts a specified VLAN tag to all TX packets for a
specified VF) . When enable port based VLAN, we use port based VLAN id
as VLAN filter entry. When disable port based VLAN, we use VLAN id of
VLAN device.
This patch fixes it for PF, enable/disable port based VLAN when calls
ndo_set_vf_vlan().
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in TX direction, driver implements the TX VLAN offload
by checking the VLAN header in skb, and filling it into TX descriptor.
Usually it works well, but if enable inserting VLAN header based on
port, it may conflict when out_tag field of TX descriptor is already
used, and cause RAS error.
In RX direction, hardware supports stripping max two VLAN headers.
For vlan_tci in skb can only store one VLAN tag, when RX VLAN offload
enabled, driver tells hardware to strip one VLAN header from RX
packet; when RX VLAN offload disabled, driver tells hardware not to
strip VLAN header from RX packet. Now if port based insert VLAN
enabled, all RX packets will have the port based VLAN header. This
header is useless for stack, driver needs to ask hardware to strip
it. Unfortunately, hardware can't drop this VLAN header, and always
fill it into RX descriptor, so driver has to identify and drop it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our hardware supports inserting a specified VLAN header for each
function when sending packets. User can enable it with command
"ip link set <devname> vf <vfid> vlan <vlan id>".
For this VLAN header is inserted by hardware, not from stack,
hardware also needs to strip it from received packets before
sending to stack. In this case, driver needs to tell
hardware which VLAN to insert or strip.
The current VLAN initialization doesn't allow inserting
VLAN header by hardware, this patch modifies it, in order be
compatible with VLAN inserted base on port.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclgevf_client_start() fails or VF driver unloaded, there is
nobody to disable keep_alive_timer.
So this patch fixes them.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checking of HCLGEVF_STATE_RST_HANDLING flag in the
hclgevf_reset_task_schedule() will make some scheduling of
reset pending fail. This flag will be checked in the
hclgevf_reset_service_task(), it is unnecessary to check it
in the hclgevf_reset_task_schedule(). So this patch removes it.
Fixes: 35a1e50343 ("net: hns3: Add VF Reset Service Task to support event handling")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds error handler for the failure of command queue
initialization both PF and VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the command queue needs re-initialization, the mailbox handling
task should do nothing, otherwise this task will just get some error
print.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ongoing lower-level reset will fail when there is a higher-level
reset occurs, so the error handler should deal with this situation.
Fixes: 6a5f6fa382 ("net: hns3: add error handler for hclgevf_reset()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware reset does not finish, the driver should not
request a new reset, otherwise the ongoing hardware reset
will get problem.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to deal with the new coming reset if
it is lower than the ongoing one.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the reset has been done successfully, the ongoing reset timer
is unnecessary.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_client_stop() should be called after unregister_netdev(),
otherwise the ongoing reset task may start the client just after it.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a vport is not alive, it is unnecessary to notify it to reset
before PF asserting a reset. So before inform vport to reset,
we need to check its alive state firstly.
Fixes: aa5c4f175b ("net: hns3: add reset handling for VF when doing PF reset")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reinitializing, the vport alive state needs to be set up.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting, the vport alive state should be set to default,
otherwise the alive state of the vport whose driver not running
is wrong before the timer to check it out.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mskid is unsigned and hence comparisons with negative
error return values are always false. Fix this by making mskid an
int.
Fixes: f058e46855 ("net: hns: fix ICMP6 neighbor solicitation messages discard problem")
Addresses-Coverity: ("Operands don't affect result")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some sparse warnings in the HNS drivers:
warning: incorrect type in assignment (different address spaces)
expected void [noderef] <asn:2> *io_base
got void *vaddr
warning: cast removes address space '<asn:2>' of expression
[...]
Add __iomem and change all the u8 __iomem to void __iomem to
fix these kind of warnings.
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:2> *base
got unsigned char [usertype] *base_addr
warning: cast to restricted __le16
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype] tbl_tcam_data_high
got restricted __le32 [usertype]
warning: cast to restricted __le32
[...]
These variables used u32/u16 as their type, and finally as a
parameter of writel(), writel() will do the cpu_to_le32 coversion
so remove the little endian covert code to fix these kind of warnings.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP6 neighbor solicitation messages will be discard by the Hip06
chips, because of not setting forwarding pool. Enable promisc mode
has the same problem.
This patch fix the wrong forwarding table configs for the multicast
vague matching when enable promisc mode, and add forwarding pool
for the forwarding table.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the HNS driver loaded, always have an error print:
"netif_napi_add() called with weight 256"
This is because the kernel checks the NAPI polling weights
requested by drivers and it prints an error message if a driver
requests a weight bigger than 64.
So use NAPI_POLL_WEIGHT to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is trying to fix the issue due to:
[27237.844750] BUG: KASAN: use-after-free in hns_nic_net_xmit_hw+0x708/0xa18[hns_enet_drv]
After hnae_queue_xmit() in hns_nic_net_xmit_hw(), can be
interrupted by interruptions, and than call hns_nic_tx_poll_one()
to handle the new packets, and free the skb. So, when turn back to
hns_nic_net_xmit_hw(), calling skb->len will cause use-after-free.
This patch update tx ring statistics in hns_nic_tx_poll_one() to
fix the bug.
Signed-off-by: Liubin Shu <shuliubin@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function hnae3_match_n_instantiate() was called both by
initializing or uninitializing client. For uninitializing, the
return value was never used.
To make it more clear, this patch splits it to two functions,
hnae3_init_client_instance() and hnae3_uninit_client_instance().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hns3_reset_notify_uninit_enet() HNS3_NIC_STATE_INITED flag
should be checked and cleared firstly.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting, the changing of MTU is not allowed, so this patch
adds checking reset status in hns3_nic_change_mtu() to do that.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_get_stats() should check the resetting status firstly,
since the device will be reinitialized when resetting. If the
reset has not completed, the hns3_get_stats() may access
invalid memory.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It used netdev->uc and netdev->mc list in function
hns3_recover_hw_addr() and hns3_remove_hw_addr().
We should add protect for them.
Fixes: f05e210971 ("net: hns3: Clear mac vlan table entries when unload driver or function reset")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
csq is used as a ring buffer, the value of the desc will be replaced
in next use. This patch removes the unnecessary memset, and just
updates the next_to_clean.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a likely case for hns3_fill_desc and
limits the local variables' scope as much as possible,
also avoid div operation when the tqp_vector->num_tqps
is one.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimizes the ring_space by calculating the
ring space without calling ring_dist.
Also ring_dist is only used by ring_space, so this patch
removes it when it is no longer used.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When set 2 same MAC to different function of one port, IMP
will return error as the later one may modify the origin one.
This will cause bond fail for 2 VFs of one port.
Driver just print warning and return 0 with this patch, so
if set same MAC address, it will return 0 but do not really
configure HW.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Method for obtaining the media type of the VF network port periodically,
regular tasks will not run until the network port UP. When the network
port is DOWN, the network port cannot obtain the media type.
Modifies the media type obtained when initializing the VF network port.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the kdump kernel started, the HNS3 driver fail to register:
[14.753340] hns3 0000:7d:00.0: Alloc umv space failed, want 512, get 0
[14.795034] hns3 0000:7d:00.0: add uc mac address fail, ret =-22.
By default, the HNS3 driver will use about 512M memory, but
usually the reserved memory of kdump kernel is 576M, so the HNS3
driver fail to register. This patch reduces the memory use in
kdump kernel to about 16M.
And when the kdump kernel starts, we must clear ucast mac address
first to avoid add fail.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hip08 SOC does not support 1000M half, this patch adds 1000M half
check for hns3_ethtool_ops.set_link_ksettings, so the user can not
set 1000M half by ethtool.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the rules for configuring search paths in Kbuild have
changed, this will lead some erros when compiling hns3 with the
following command:
make O=DIR M=drivers/net/ethernet/hisilicon/hns3
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:11:10:
fatal error: hnae3.h: No such file or directory
This patch fix it by adding $(srctree)/ prefix to the serach paths.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added IANA_VXLAN_UDP_PORT (4789) definition to vxlan header file so it
can be used by drivers instead of local definition.
Updated drivers which locally defined it as 4789 to use it.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: John Hurley <john.hurley@netronome.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Yunsheng Lin <linyunsheng@huawei.com>
Cc: Peng Li <lipeng321@huawei.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When there is only one byte in a frag, the current calculation
using "(size + HNS3_MAX_BD_SIZE - 1) >> HNS3_MAX_BD_SIZE_OFFSET"
will return zero, because HNS3_MAX_BD_SIZE is 65535 and
HNS3_MAX_BD_SIZE_OFFSET is 16. So it will cause tx error when
a frag's size is one byte.
This patch fixes it by using DIV_ROUND_UP.
Fixes: 3fe13ed95d ("net: hns3: avoid mult + div op in critical data path")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:414:6:
warning: symbol 'hclge_destroy_cmd_queue' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.
We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.
Tested with ixgbe and CONFIG_FCOE=m
With pktgen using queue xmit:
threads vanilla patched
(kpps) (kpps)
1 2334 2428
2 4166 4278
4 7895 8100
v1 -> v2:
- rebased after helper's name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c:407:6:
warning: symbol 'hclgevf_update_link_mode' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit bfcb79fca1
("PCI/ERR: Run error recovery callbacks for all affected devices")
affected the non-fatal error recovery logic for the HNS and RDMA devices.
This is because each HNS PF under PCIe bus receive callbacks
from the AER driver when an error is reported for one of the PF.
This causes unwanted PF resets because
the HNS decides which PF to reset based on the reset type set.
The HNS error handling code sets the reset type based on the hw error
type detected.
This patch provides fix for the above issue for the recovery of
the hw errors in the HNS and RDMA devices.
This patch needs backporting to the kernel v5.0+
Fixes: 332fbf5765 ("net: hns3: add handling of hw ras errors using new set of commands")
Reported-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW can not guarantee complete write desc->rx.size, even though
HNS3_RXD_VLD_B has been set. Driver needs to add dma_rmb()
instruction to make sure desc->rx.size is always valid.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a couple logical ORs accidentally mixed in with the bitwise
ORs.
Fixes: e8149933b1 ("net: hns3: remove hnae3_get_bit in data path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(struct boo) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hns3_client_start() failed in the hns3_client_init(),
register_dev() should be undo in its error handling.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presently the hns reset_type for the roce errors is set
in the hclge_log_and_clear_rocee_ras_error function.
This function is also called to detect and clear roce errors
while enabling the rdma error interrupts. However there is no hns
reset requested for this case. This can cause issue of wrong
reset_type used with subsequent hns reset as the
reset_type set in the above case was not cleared.
This patch moves setting of hns reset_type for the roce errors from
hclge_log_and_clear_rocee_ras_error function
to hclge_handle_rocee_ras_error.
Fixes: 630ba007f4 ("net: hns3: add handling of RDMA RAS errors")
Reported-by: Huazhong Tan <tanhuazhong@huawei.com>
Reported-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, VF shares the same RSS config with PF.
In original codes, it always return 0 when query RSS hash
key for VF. This patch fixes it by return the hash key
got from PF.
Fixes: 374ad29176 ("net: hns3: net: hns3: Add RSS general configuration support for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x21, the switch of VF VLAN filter is per function.
It's necessary to enable VF VLAN filter for each VF when initializing.
Otherwise, VF will be able to receive broadcast packets with unknown
VLAN when PF enters promisc mode.
Fixes: 64d114f0a7 ("net: hns3: Add egress/ingress vlan filter for revision 0x21")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to config depth for tx|rx ring separately
by ethtool command "-G".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hnae3_get_bit uses hnae3_get_field, and hnae3_get_field
masks the data, which is unnecessary in data path.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hnae3_set_bit and hnae3_set_field masks the data before setting
the field or bit, which is unnecessary because the data is already
zero initialized.
Suggested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds unlikely hint for error handling in critical data
path.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fill_desc ops has only one implementation, and
get_rxd_bnum has not been used, so this patch removes
them.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch limits some variables' scope as much as possible in
hns3_fill_desc.
Also, only set l3_type and l4_type when necessary.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses shift offset to avoid doing mult and div operation.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds xps setting support for hns3 driver based on
the interrupt affinity info.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware's description, the driver should clear
the command queue's registers when uloading VF driver. Otherwise,
these existing value may lead the IMP get into a wrong state.
Fixes: fedd0c15d2 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware's description, the driver should clear
the command queue's registers when uloading driver. Otherwise,
these existing value may lead the IMP get into a wrong state.
Also this patch adds hclge_cmd_uninit() to do the command queue
uninitialization which includes clearing registers and freeing
memory.
Fixes: 68c0a5c706 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the vlan tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the unicast and multicast tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modify print message of 6th bit of ppp mpf abnormal errors,
there is a extra letter e in it.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These bits are enabled now and have been test.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3rd and 4th of PPU(RCB) PF Abnormal is RAS errors instead of MSI-X
like other bits. This patch adds process of handling and logging this
two bits. Otherwise, this patch modifies print message of 28th and 29th
bit of PPU MPF Abnormal errors, which keep same with other errors now.
Fixes: f69b10b317 ("net: hns3: handle hw errors of PPU(RCB)")
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add information of specific bit in log to be consistent
with other type of errors, so that we can know which memory of ssu
has occurred a ecc ras errors.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, for copper port which doesn't connect to phy,
it always returns -EOPNOTSUPP when query port information. This
patch fixes it by return the port information of MAC.
Fixes: 5f373b1585 ("net: hns3: Fix speed/duplex information loss problem when executing ethtool ethx cmd of VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link mode with bits has been up to more than 31 for some MAC
and phy. Convert to using a linkmode bitmap, which can support all
link modes.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hnae3_register_ae_dev(), ae_algo->ops is assigned to ae_dev->ops
before check that ae_algo->ops is valid.
And in hnae3_register_ae_algo(), missing check for ae_algo->ops.
This patch fixes them.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are exported, add pointer checking at the beginning
can make them more safe.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the missing device reference release-after-use in
the positive leg of the roce reset API of the HNS DSAF.
Fixes: c969c6e7ab ("net: hns: Fix object reference leaks in hns_dsaf_roce_reset()")
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:2431:5: warning:
symbol 'hclge_set_all_vf_rst' was not declared. Should it be static?
Fixes: aa5c4f175b ("net: hns3: add reset handling for VF when doing PF reset")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating the available MAC VLAN table counts,
MAC VLAN table entry count function adds
operation 0 value protection measures.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to prevent the variable anomaly from being larger than desc_num,
the upper limit judgment condition becomes >=.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user disables vlan filter, and adds vlan device, it won't
notify the driver the update the vlan filter. In this case, when
user enables vlan filter again, the packets with new vlan tag
will be filtered by vlan filter.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple macros with the largest number of TCs in the system,
optimized to HCLGE_MAX_TC_NUM.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Run ethtool ethx when displaying device information in VF，
the supported port and link mode items will be empty.
This patch fixes it.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the TC is enabled, we need to check whether the buffer is enough,
otherwise it may lead to a wrong -ENOMEM case.
Fixes: 9ffe79a9c2 ("net: hns3: Support for dynamically assigning tx buffer to TC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does not change the code logic. There are some same
set_bit statements called by add/rm_uc/mc_addr_common, and move
this statements into hclge_prepare_mac_addr to reduce duplicate
code.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For simplifying the code, this patch adds hclge_cmd_check_retval() to
check the return value of the command.
Also, according the IMP's description, when there are several descriptors
in a command, then the IMP will save the return value on the last
description, so hclge_cmd_check_retval() just check the last one for this
case.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are four steps to calcuate the rx private buffer, each step
can be done in a function to avoid code duplication and aid code
readability.
This patch adds three separate functions do the job. Also, the
function name more or less make the comment redundant, so remove
some obvious comment.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second parameter to the hook function set_gro_en is always passed in
true/false, so modify it's type from int to bool.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 supports setting rx-usecs|tx-usecs as 0, but it will not
update dynamically when adaptive-tx or adaptive-rx is enable.
This patch removes the Redundant check.
Fixes: a95e1f8666 ("net: hns3: change the time interval of int_gl calculating")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same code style for rx_group and tx_group in the
hns3_update_new_int_gl().
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should return -ENOMEM if the kcalloc() fails.
Fixes: d174ea75c9 ("net: hns3: add statistics for PFC frames and MAC control frame")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In orginal codes, driver always enables flow director when
intializing. When user disable flow director with command
ethtool -K, the flow director will be enabled again after
resetting.
This patch fixes it by only enabling it when first initialzing.
Fixes: 6871af29b3 ("net: hns3: Add reset handle for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF is resetting, it can't communicate to PF with mailbox msg.
This patch adds reset state checking before sending keep alive msg
to PF.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 VF driver support NIC and Roce, hdev stores NIC
handle and Roce handle, should use correct parameter for
container_of.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hclge_init_umv_space() failed in the hclge_init_ae_dev(),
we should undo all the operation which has been done successfully,
the last success operation maybe hclge_mac_mdio_config(), so if
hclge_init_umv_space() failed, we also need to undo it.
Fixes: 288475b2ad01 ("{topost} net: hns3: refine umv space allocation")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rss result is more uniform when use recommended hash key from
microsoft, instead of the one generated by netdev_rss_key_fill().
Also using hash algorithm "xor" is better than "toeplitz".
This patch modifies the default hash key and hash algorithm.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
