Currently, the tx unicast promisc is always enabled when promisc
mode on. If tx unicast promisc on, a function will receive all
unicast packet from other functions belong to the same port.
Add a ethtool private flag to control whether enable tx
unicast promisc. Then the function is able to filter the
unknown unicast packets from other function.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the PF driver removes all (including its VFs') MAC/VLAN
flow director table entries when resetting, and restores them after
reset completed.
In fact, the hardware will clear all table entries only in IMP
reset and global reset. So driver only needs to restore the table
entries in these cases, and needs do nothing when PF reset, FLR
or other function level reset.
This patch optimizes it by removing unnecessary table entries clear
and restoring handling in the reset flow, and doing the restoring
after reset completed.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, PF responds to VF depending on what mailbox it is
handling, it is a bit inflexible. The correct way is, PF should
check the mbx_need_resp field to decide whether gives response
to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For making the code more readable, this adds several new
structure to replace the msg field in structure
hclge_mbx_vf_to_pf_cmd and hclge_mbx_pf_to_vf_cmd.
Also uses macro to instead of some magic number.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if VF is loaded on the host side, the host doesn't
clear the VF's VLAN table entries when VF removing. In this
case, when doing reset and disabling sriov at the same time the
VLAN device over VF will be removed, but the VLAN table entries
in hardware are remained.
This patch fixes it by asking PF to clear the VLAN table entries for
VF when VF is removing. It also clears the VLAN table full bit
after VF VLAN table entries being cleared.
Fixes: c6075b1934 ("net: hns3: Record VF vlan tables")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using '%d' for printing type unsigned int or '%u' for
type int would cause static tools to give false warnings,
so this patch cleanups this warning by using the suitable
format specifier of the type of variable.
BTW, modifies the type of some variables and macro to
synchronize with their usage.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the comment for macro HCLGE_MBX_GET_VF_FLR_STATUS
more correct, and adds comments in some place to make the code more
readable.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds supports for setting VF trust by host. If specified
VF is trusted, then it can enable promisc(include allmulti mode).
If a trusted VF enabled promisc, and being untrusted, host will
disable promisc mode for this VF.
For VF will update its promisc mode from set_rx_mode now, so it's
unnecessary to set broadcst promisc mode when initialization or
reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
When NCSI has HW error, the IMP will report this error to the driver
by sending a mailbox. After received this message, the driver should
assert a global reset to fix this kind of HW error.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, PF updates link status per second. For some scenario,
it requires link down event being reported more quickly.
To solve it, firmware pushes the link change event to PF with
CMDQ message, and driver updates the link status directly.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All constant in 'enum HCLGE_MBX_OPCODE' start with HCLGE, except
'HLCGE_MBX_PUSH_VLAN_INFO' (C and L switched)
s/HLC/HCL/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to user manual, the maximum size of mailbox responding
data is 8 bytes, the macro HCLGE_MBX_MAX_RESP_DATA_SIZE
should be defined as 8 instead of 16.
Fixes: 9194d18b05 ("net: hns3: fix the problem that the supported port is empty")
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses a reserved byte in the hclge_mbx_vf_to_pf_cmd
to save the need_resp flag, so when PF received the mailbox,
it can use it to decise whether send a response to VF.
For hclge_set_vf_uc_mac_addr(), it should use mbx_need_resp flag
to decide whether send response to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since irq handler and mailbox task will both update arq's count,
so arq's count should use atomic_t instead of u32, otherwise
its value may go wrong finally.
Fixes: 07a0556a3a ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.
This patch fixes it. When VF loads up, it firstly queries the port
based VLAN state from PF. When user change port based VLAN state
from PF, PF firstly checks whether the VF is alive. If the VF is
alive, then PF notifies the VF the modification; otherwise PF
configure the port based VLAN state directly.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Method for obtaining the media type of the VF network port periodically,
regular tasks will not run until the network port UP. When the network
port is DOWN, the network port cannot obtain the media type.
Modifies the media type obtained when initializing the VF network port.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the unicast and multicast tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Run ethtool ethx when displaying device information in VF，
the supported port and link mode items will be empty.
This patch fixes it.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds mtu setting support for vf, currently
vf and pf share the same hardware mtu setting. Mtu set
by vf must be less than or equal to pf' mtu, and mtu
set by pf must be greater than or equal to vf' mtu.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way for pf to know if a vf device is
alive or not, so PF does not know which vf to notify when
reset happens, or which vf's mtu is invalid when vf and pf
share the same hardware mtu setting.
This patch adds vport alive state checking support, in order
to support the above scenario.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PF performs a function reset, the hardware will reset both PF
and all the VF belong to this PF. Hence, both PF's driver and VF's
driver need to perform corresponding reset operations.
Before PF driver asserting function reset to hardware, it firstly
set up VF's hardware reset status, and inform the VF driver with
HNAE3_VF_PF_FUNC_RESET, then VF driver sets this reset type to
reset_pending and shechule reset task to stop IO and waits for the
hardware reset status to clear. When PF driver has reinitialized the
hardware and is ready to process mailbox from VF, PF driver clears
VF's hardware reset status for VF to continue its reset process.
Also, this patch uses readl_poll_timeout to simplify the hardware reset
status waitting.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the update flow of the new PF driver, if a multicast address is in mta
table, the VF deletion action will not take effect.
This patch adds the VF adaptation according to the new flow of PF'driver.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Reviewed-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset Asserting message is forwarded by PF to inform VF about
the hardware reset which is about to happen. This might be due
to the earlier VF reset request received by the PF or because PF
for any reason decides to undergo reset. This message results in
VF to go in pending state in which it polls the hardware to
complete the reset and then further resets/tears its own stack.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current mailbox CRQ could consists of both synchronous and async
responses from the PF. Synchronous responses are time critical
and should be handed over to the waiting tasks/context as quickly
as possible otherwise timeout occurs.
Above problem gets accentuated if CRQ consists of even single
async message. Hence, it is important to have quick handling of
synchronous messages and maybe deferred handling of async messages
This patch introduces separate ARQ(async receive queues) for the
async messages. These messages are processed later with repsect
to mailbox task while synchronous messages still gets processed
in context to mailbox interrupt.
ARQ is important as VF reset introduces some new async messages
like MBX_ASSERTING_RESET which adds up to the presssure on the
responses for synchronousmessages and they timeout even more
quickly.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the buffer overflow warning by refactoring
hclgevf_bind_ring_to_vector and hclge_get_ring_chain_from_mbx.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of the mailbox to the VF driver. The
mailbox shall be used as an interface to communicate with the
PF driver for various purposes like {set|get} MAC related
operations, reset, link status etc. The mailbox supports both
synchronous and asynchronous command send to PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
