When packets are received on the error queue, this function under
net_ratelimit():
netif_err(priv, hw, net_dev, "Err FD status = 0x%08x\n");
does not get printed. Instead we only see:
[ 3658.845592] net_ratelimit: 244 callbacks suppressed
[ 3663.969535] net_ratelimit: 230 callbacks suppressed
[ 3669.085478] net_ratelimit: 228 callbacks suppressed
Enabling NETIF_MSG_HW fixes this issue, and we can see some information
about the frame descriptors of packets.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() does a PHY reset, which means the PHY
loses its register settings. The fec_enet_mii_probe() starts the PHY
and does the necessary calls to configure the PHY via PHY framework,
and loads the correct register settings into the PHY. Therefore,
fec_enet_mii_probe() should be called only after the PHY has been
reset, not before as it is now.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the new group of devlink traps - PARSER_ERROR_DROPS.
This consists of registering the array of parser error drops supported,
controlling their action through the .trap_group_action_set() callback
and reporting an erroneous skb received on the error queue
appropriately.
DPAA2 devices do not support controlling the action of independent
parser error traps, thus the .trap_action_set() callback just returns an
EOPNOTSUPP while .trap_group_action_set() actually notifies the hardware
what it should do with a frame marked as having a header error.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support in dpaa2-eth for devlink. For the moment, just
register the device with devlink, add the corresponding devlink port and
implement the .info_get() callback.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
mpc52xx_fec_stop() uses in_interrupt() to check if it is safe to sleep. All
callers run in well defined contexts.
Pass an argument from the callers indicating whether it is safe to sleep.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a null-check for _pcs_, but it is being dereferenced
prior to this null-check. So, if _pcs_ can actually be null,
then there is a potential null pointer dereference that should
be fixed by null-checking _pcs_ before being dereferenced.
Addresses-Coverity-ID: 1497159 ("Dereference before null check")
Fixes: 94ae899b20 ("dpaa2-mac: add PCS support through the Lynx module")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SHARED_FS is enabled on a DPNI object the flow steering tables are
shared between all the traffic classes. Modify the driver so that we
only add a new flow steering entry on the TC#0 when this new option is
enabled.
Signed-off-by: Ionut-robert Aron <ionut-robert.aron@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to dpaa2_eth_link_state_update() is a leftover from the time
when on DPAA2 platforms the PHYs were started at boot time so when an
ifconfig was issued on the associated interface, the link status needed
to be checked directly from the ndo_open() callback.
This is not needed anymore since we are now properly integrated with the
PHY layer thus a link interrupt will come directly from the PHY
eventually without the need to call the sync function.
Fix this up by removing the call to dpaa2_eth_link_state_update().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to check if both the MDIO controller node and its
child node, the PCS device, are available since there is no chance that
the child node would be enabled when the parent it's not.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the support for TBF offload, the improper command version
was added even though the command format is for the V2 of
dpni_set_tx_shaping(). This does not affect the functionality of TBF
since the only change between these two versions is the addition of the
exceeded parameters which are not used in TBF. Still, fix the bug so
that we keep things in sync.
Fixes: 39344a8962 ("dpaa2-eth: add API for Tx shaping")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO reads can happen during PHY probing, and printing an error with
dev_err can result in a large number of error messages during device
probe. On a platform with a serial console this can result in
excessively long boot times in a way that looks like an infinite loop
when multiple busses are present. Since 0f183fd151 (net/fsl: enable
extended scanning in xgmac_mdio) we perform more scanning so there are
potentially more failures.
Reduce the logging level to dev_dbg which is consistent with the
Freescale enetc driver.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include PCS support in the dpaa2-eth driver by integrating it with the
new Lynx PCS module. There is not much to talk about in terms of changes
needed in the dpaa2-eth driver since the only steps necessary are to
find the MDIO device representing the PCS, register it to the Lynx PCS
module and then let phylink know if its existence also.
After this, the PCS callbacks will be treated directly by Lynx, without
interraction from dpaa2-eth's part.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the return expression.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(struct scatterlist),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix below sparse warning in dpmac.c.
warning: cast to restricted __le64
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add PTP sync packet one-step timestamping support.
Before egress, one-step timestamping enablement needs,
- Enabling timestamp and FAS (Frame Annotation Status) in
dpni buffer layout.
- Write timestamp to frame annotation and set PTP bit in
FAS to mark as one-step timestamping event.
- Enabling one-step timestamping by dpni_set_single_step_cfg()
API, with offset provided to insert correction time on frame.
The offset must respect all MAC headers, VLAN tags and other
protocol headers accordingly. The correction field update can
consider delays up to one second. So PTP frame needs to be
filtered and parsed, and written timestamp into Sync frame
originTimestamp field.
The operation of API dpni_set_single_step_cfg() has to be done
when no one-step timestamping frames are in flight. So we have
to make sure the last one-step timestamping frame has already
been transmitted on hardware before starting to send the current
one. The resolution is,
- Utilize skb->cb[0] to mark timestamping request per packet.
If it is one-step timestamping PTP sync packet, queue to skb queue.
If not, transmit immediately.
- Schedule a work to transmit skbs in skb queue.
- mutex lock is used to ensure the last one-step timestamping packet
has already been transmitted on hardware through TX confirmation queue
before transmitting current packet.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a preparation for next hardware one-step timestamping
support. For DPAA2, the one step timestamping configuration on
hardware registers has to be done when there is no one-step timestamping
packet in flight. So we will have to use workqueue and skb queue
for such packets transmitting, to make sure waiting the last packet has
already been sent on hardware, and starting to transmit the current one.
So the tx timestamping flag in private data may not reflect the actual
request for the one-step timestamping packets of skb queue. This also
affects skb headroom allocation. Let's use skb->cb[0] to mark the
timestamping request for each skb.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke dpaa2_eth_enable_tx_tstamp() once in code after building FD,
rather than calling it in dpaa2_eth_build_single_fd(),
dpaa2_eth_build_sg_fd_single_buf(), and dpaa2_eth_build_sg_fd().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a global ptp_qoriq structure pointer, and export to use.
The ptp clock operations will be used in dpaa2-eth driver.
For example, supporting one step timestamping needs to write
current time to hardware frame annotation before sending and
then hardware inserts the delay time on frame during sending.
So in driver, at least clock gettime operation will be needed
to make sure right time is written to hardware frame annotation
for one step timestamping.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add APIs of 1588 single step timestamping.
- dpni_set_single_step_cfg
- dpni_get_single_step_cfg
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/freescale/fec_ptp.c:523:6: warning:
variable 'ns' set but not used [-Wunused-but-set-variable]
523 | u64 ns;
| ^~
After commit 6605b730c0 ("FEC: Add time stamping code and a PTP
hardware clock"), variable 'ns' is never used in fec_time_keep(),
so removing it to avoid build warning.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the correct resolution for the conflict from
merging the "net" tree fix:
commit 26cb7085c8 ("enetc: Remove the mdio bus on PF probe bailout")
with the "net-next" new work:
commit 07095c025a ("net: enetc: Use DT protocol information to set up the ports")
that moved mdio bus allocation to an ealier stage of
the PF probing routine.
Fixes: a57066b1a0 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some static functions in the dpaa2-eth driver don't have the dpaa2_eth_
prefix and this is becoming an inconvenience when looking at, for
example, a perf top output and trying to determine easily which entries
are dpaa2-eth related. Ammend this by adding the prefix to all the
functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some static functions in the dpaa2-eth driver don't have the dpaa2_eth_
prefix and this is becoming an inconvenience when looking at, for
example, a perf top output and trying to determine easily which entries
are dpaa2-eth related. Ammend this by adding the prefix to all the
functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some static functions in the dpaa2-eth driver don't have the dpaa2_eth_
prefix and this is becoming an inconvenience when looking at, for
example, a perf top output and trying to determine easily which entries
are dpaa2-eth related. Ammend this by adding the prefix to all the
functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the error path for regulator disable.
Fixes: 9269e5560b ("net: fec: add phy-reset-gpios PROBE_DEFER check")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix smatch warning:
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:2419
alloc_channel() warn: passing zero to 'ERR_PTR'
setup_dpcon() should return ERR_PTR(err) instead of zero in error
handling case.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls napi_schedule_irqoff() from a context where, in RT,
hardirqs are not disabled, since the IRQ handler is force-threaded.
In the call path of this function, __raise_softirq_irqoff() is modifying
its per-CPU mask of pending softirqs that must be processed, using
or_softirq_pending(). The or_softirq_pending() function is not atomic,
but since interrupts are supposed to be disabled, nobody should be
preempting it, and the operation should be safe.
Nonetheless, when running with hardirqs on, as in the PREEMPT_RT case,
it isn't safe, and the pending softirqs mask can get corrupted,
resulting in softirqs being lost and never processed.
To have common code that works with PREEMPT_RT and with mainline Linux,
we can use plain napi_schedule() instead. The difference is that
napi_schedule() (via __napi_schedule) also calls local_irq_save, which
disables hardirqs if they aren't already. But, since they already are
disabled in non-RT, this means that in practice we don't see any
measurable difference in throughput or latency with this patch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls napi_schedule_irqoff() from a context where, in RT,
hardirqs are not disabled, since the IRQ handler is force-threaded.
In the call path of this function, __raise_softirq_irqoff() is modifying
its per-CPU mask of pending softirqs that must be processed, using
or_softirq_pending(). The or_softirq_pending() function is not atomic,
but since interrupts are supposed to be disabled, nobody should be
preempting it, and the operation should be safe.
Nonetheless, when running with hardirqs on, as in the PREEMPT_RT case,
it isn't safe, and the pending softirqs mask can get corrupted,
resulting in softirqs being lost and never processed.
To have common code that works with PREEMPT_RT and with mainline Linux,
we can use plain napi_schedule() instead. The difference is that
napi_schedule() (via __napi_schedule) also calls local_irq_save, which
disables hardirqs if they aren't already. But, since they already are
disabled in non-RT, this means that in practice we don't see any
measurable difference in throughput or latency with this patch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory allocation for ethernet address hash table.
The code was wrongly allocating an array for eth hash table which
is incorrect because this is the main structure for eth hash table
(struct eth_hash_t) that contains inside a number of elements.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a safe check to avoid dereferencing null pointer
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter 'priority' is incorrectly forced to zero which ultimately
induces logically dead code in the subsequent lines.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check before using returned value to avoid dereferencing null pointer.
Fixes: 18a6c85fcc ("fsl/fman: Add FMan Port Support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Potentially overflowing expression (ts_freq << 16 and intgr << 16)
declared as type u32 (32-bit unsigned) is evaluated using 32-bit
arithmetic and then used in a context that expects an expression of
type u64 (64-bit unsigned) which ultimately is used as 16-bit
unsigned by typecasting to u16. Fixed by using an unsigned 32-bit
integer since the value is truncated anyway in the end.
Fixes: 414fd46e77 ("fsl/fman: Add FMan support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of invalid rule, a positive value EINVAL is returned here.
I think this is a typo error. It is necessary to return an error value.
Cc: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
For ENETC ports that register an external MDIO bus,
the bus doesn't get removed on the error bailout path
of enetc_pf_probe().
This issue became much more visible after recent:
commit 07095c025a ("net: enetc: Use DT protocol information to set up the ports")
Before this commit, one could make probing fail on the error
path only by having register_netdev() fail, which is unlikely.
But after this commit, because it moved the enetc_of_phy_get()
call up in the probing sequence, now we can trigger an mdiobus_free()
bug just by forcing enetc_alloc_msix() to return error, i.e. with the
'pci=nomsi' kernel bootarg (since ENETC relies on MSI support to work),
as the calltrace below shows:
kernel BUG at /home/eiz/work/enetc/net/drivers/net/phy/mdio_bus.c:648!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[...]
Hardware name: LS1028A RDB Board (DT)
pstate: 80000005 (Nzcv daif -PAN -UAO BTYPE=--)
pc : mdiobus_free+0x50/0x58
lr : devm_mdiobus_free+0x14/0x20
[...]
Call trace:
mdiobus_free+0x50/0x58
devm_mdiobus_free+0x14/0x20
release_nodes+0x138/0x228
devres_release_all+0x38/0x60
really_probe+0x1c8/0x368
driver_probe_device+0x5c/0xc0
device_driver_attach+0x74/0x80
__driver_attach+0x8c/0xd8
bus_for_each_dev+0x7c/0xd8
driver_attach+0x24/0x30
bus_add_driver+0x154/0x200
driver_register+0x64/0x120
__pci_register_driver+0x44/0x50
enetc_pf_driver_init+0x24/0x30
do_one_initcall+0x60/0x1c0
kernel_init_freeable+0x1fc/0x274
kernel_init+0x14/0x110
ret_from_fork+0x10/0x34
Fixes: ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enetc_imdio_remove() is missing from the enetc_pf_probe()
bailout path. Not surprisingly because enetc_setup_serdes()
is registering the imdio bus for internal purposes, and it's
not obvious that enetc_imdio_remove() currently performs the
teardown of enetc_setup_serdes().
To fix this, define enetc_teardown_serdes() to wrap
enetc_imdio_remove() (improve code maintenance) and call it
on bailout and remove paths.
Fixes: 975d183ef0 ("net: enetc: Initialize SerDes for SGMII and USXGMII protocols")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
React to TC_SETUP_QDISC_TBF and configure the egress shaper as
appropriate with the maximum rate and burst size requested by the user.
TBF can only be offloaded on DPAA2 when it's the root qdisc, ie it's a
per port shaper.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary API (dpni_set_tx_shaping) for configuring the rate and
burst size of a per port shaper in DPAA2.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the setup done for MQPRIO into a separate function so that
with the addition of another offload we do not crowd
dpaa2_eth_setup_tc(). After this restructuring it's easier to see what
is supported in terms of Qdisc offloading.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic dynamic interrupt moderation (dim)
framework to implement adaptive interrupt coalescing
on Rx. With the per-packet interrupt scheme, a high
interrupt rate has been noted for moderate traffic flows
leading to high CPU utilization. The 'dim' scheme
implemented by the current patch addresses this issue
improving CPU utilization while using minimal coalescing
time thresholds in order to preserve a good latency.
On the Tx side use an optimal time threshold value by
default. This value has been optimized for Tx TCP
streams at a rate of around 85kpps on a 1G link,
at which rate half of the Tx ring size (128) gets filled
in 1500 usecs. Scaling this down to 2.5G links yields
the current value of 600 usecs, which is conservative
and gives good enough results for 1G links too (see
next).
Below are some measurement results for before and after
this patch (and related dependencies) basically, for a
2 ARM Cortex-A72 @1.3Ghz CPUs system (32 KB L1 data cache),
using 60secs log netperf TCP stream tests @ 1Gbit link
(maximum throughput):
1) 1 Rx TCP flow, both Rx and Tx processed by the same NAPI
thread on the same CPU:
CPU utilization int rate (ints/sec)
Before: 50%-60% (over 50%) 92k
After: 13%-22% 3.5k-12k
Comment: Major CPU utilization improvement for a single flow
Rx TCP flow (i.e. netperf -t TCP_MAERTS) on a single
CPU. Usually settles under 16% for longer tests.
2) 4 Rx TCP flows + 4 Tx TCP flows (+ pings to check the latency):
Total CPU utilization Total int rate (ints/sec)
Before: ~80% (spikes to 90%) ~100k
After: 60% (more steady) ~4k
Comment: Important improvement for this load test, while the
ping test outcome does not show any notable
difference compared to before.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable programming of the interrupt coalescing registers
and allow manual configuration of the coalescing time
thresholds via ethtool. Packet thresholds have been fixed
to predetermined values as there's no point in making them
run-time configurable, also anticipating the dynamic interrupt
moderation (DIM) algorithm which uses fixed packet thresholds
as well. If the interface is up when the operation mode of
traffic interrupt events is changed by the user (i.e. switching
from default per-packet interrupts to coalesced interrupts),
the traffic needs to be paused in the process.
This patch also prepares the ground for introducing DIM on Rx.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'struct enetc_bdr' is already '____cacheline_aligned_in_smp'.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt coalescing registers naming in the current revision
of the Ref Man (RM) is ICR, deprecating the ICIR name used
in earlier (draft) versions of the RM.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A reliable traffic pause (and reconfiguration) procedure
is needed to be able to safely make h/w configuration
changes during run-time, like changing the mode in which the
interrupts are operating (i.e. with or without coalescing),
as opposed to making on-the-fly register updates that
may be subject to h/w or s/w concurrency issues.
To this end, the code responsible of the run-time device
configurations that basically starts resp. stops the traffic
flow through the device has been extracted from the
the enetc_open/_close procedures, to the separate standalone
enetc_start/_stop procedures. Traffic stop should be as
graceful as possible, it lets the executing napi threads to
to finish while the interrupts stay disabled. But since
the napi thread will try to re-enable interrupts by clearing
the device's unmask register, the enable_irq/ disable_irq
API has been used to avoid this potential concurrency issue
and make the traffic pause procedure more reliable.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's time to differentiate between Rx and Tx ring sizes.
Not only Tx rings are processed differently than Rx rings,
but their default number also differs - i.e. up to 8 Tx rings
per device (8 traffic classes) vs. 2 Rx rings (one per CPU).
So let's set Tx rings sizes to half the size of the Rx rings
for now, to be conservative.
The default ring sizes were decreased as well (to the next
lower power of 2), to reduce the memory footprint, buffering
etc., since the measurements I've made so far show that the
rings are very unlikely to get full.
This change also anticipates the introduction of the
dynamic interrupt moderation (dim) algorithm which operates
on maximum packet thresholds of 256 packets for Rx and 128
packets for Tx.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dma_coerce_mask_and_coherent() fails, the alloced netdev need to be freed.
Fixes: 060ad66f97 ("dpaa_eth: change DMA device")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because clk_prepare_enable and clk_disable_unprepare already
checked NULL clock parameter, so the additional checks are
unnecessary, just remove them.
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DT information rather than in-band information from bootloader to
set up MAC for XGMII. For RGMII use the DT indication in addition to
RGMII defaults in hardware.
However, this implies that PHY connection information needs to be
extracted before netdevice creation, when the ENETC Port MAC is
being configured.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC has ethernet MACs capable of SGMII, 2500BaseX and USXGMII. But in
order to use these protocols some SerDes configurations need to be
performed. The SerDes is configurable via an internal PCS PHY which is
connected to an internal MDIO bus at address 0.
This patch basically removes the dependency on bootloader regarding
SerDes initialization.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to use snprintf() on a constant string, nor using magic
constant in the fixed code was a good idea.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Code of the form "if(x) x = 0" replaced with "x = 0".
Code of the form "if(x == a) x = a" removed.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initializing with 0 makes it much easier to identify time stamps from
otherwise uninitialized clock.
Initialization of PTP clock with current kernel time makes little sense as
PTP time scale differs from UTC time scale that kernel time represents.
It only leads to confusion when no actual PTP initialization happens, as
these time scales differ in a small integer number of seconds (37 at the
time of writing.)
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PPS feature could be useful even when hardware time stamping
of network packets is not in use, so remove offending check
for this condition from fec_ptp_enable_pps().
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix support for external PTP-aware devices such as DSA or PTP PHY:
Make sure we never time stamp tx packets when hardware time stamping
is disabled.
Check for PTP PHY being in use and then pass ioctls related to time
stamping of Ethernet packets to the PTP PHY rather than handle them
ourselves. In addition, disable our own hardware time stamping in this
case.
Fixes: 6605b730c0 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The fsl_mc_get_endpoint() function can return an error or directly a
NULL pointer in case the peer device is not under the root DPRC
container. Treat this case also, otherwise it would lead to a NULL
pointer when trying to access the peer fsl_mc_device.
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If there is no valid MAC address in the device tree,
use a random MAC address.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC allocates 2K buffers, but looses some of it due to
alignment. It can however support an MTU bigger than the default. This
is particularly interesting when used in combination with Ethernet
switches supporting DSA, which have extra headers. The DSA core will
try to increase the MTU to support these extra headers. If the max
size defaults to that of standard Ethernet we get a warning. By
setting the max to what the driver actually supports, we avoid this
warning.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to use eth_broadcast_addr() to assign broadcast address
insetad of memset().
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ISR, we poll the event register for the queues in need of
service and then enter polled mode. After this point, the event
register will never be read again until we exit polled mode.
In a scenario where a UDP flow is routed back out through the same
interface, i.e. "router-on-a-stick" we'll typically only see an rx
queue event initially. Once we start to process the incoming flow
we'll be locked polled mode, but we'll never clean the tx rings since
that event is never caught.
Eventually the netdev watchdog will trip, causing all buffers to be
dropped and then the process starts over again.
Rework the NAPI poll to keep trying to consome the entire budget as
long as new events are coming in, making sure to service all rx/tx
queues, in priority order, on each pass.
Fixes: 4d494cdc92 ("net: fec: change data structure to support multiqueue")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On link down, the draining of the S/G cache should be done on all
_possible_ CPUs not just the ones that are online in that moment.
Fix this by changing the iterator.
Fixes: d70446ee1f ("dpaa2-eth: send a scatter-gather FD instead of realloc-ing")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the previous commit, in case of insufficient SKB headroom on the Tx
path instead of reallocing the SKB we now send a S/G frame descriptor.
Export the number of occurences of this case as a per CPU counter (in
debugfs) and a total number in the ethtool statistics - "tx converted sg
frames'.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of realloc-ing the skb on the Tx path when the provided headroom
is smaller than the HW requirements, create a Scatter/Gather frame
descriptor with only one entry.
Remove the '[drv] tx realloc frames' counter exposed previously through
ethtool since it is no longer used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 'tcfp_burst' with TICK factor, driver side always need to recover
it to the original value, this patch moves the generic calculation and
recover to the 'burst' original value before offloading to device driver.
Signed-off-by: Po Liu <po.liu@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rings bitmap of an interrupt vector encodes
which of the device's rings were assigned to that
interrupt vector.
Hence the iteration range of the tx rings bitmap
(for_each_set_bit()) should be the total number of
Tx rings of that netdevice instead of the number of
rings assigned to the interrupt vector.
Since there are 2 cores, and one interrupt vector for
each core, the number of rings asigned to an interrupt
vector is half the number of available rings.
The impact of this error is that the upper half of the
tx rings could still generate interrupts during napi
polling.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Two of the function parameters (qtype and index) were misspelled in the
associated descriptions of dpni_[set/get]_taildrop which led to sparse
warnings. Fix this by using the exact same names as present in the
function definition.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2-eth.h header file includes dpaa2-eth-trace.h which includes
back dpaa2-eth leading to a recursion in the include path. Fix this by
removing the include of dpaa2-eth.h in the trace header.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should keep retrying to acquire buffers through the software portals
as long as the function returns -EBUSY and the number of retries is
__below__ DPAA2_ETH_SWP_BUSY_RETRIES.
Fixes: ef17bd7cc0 ("dpaa2-eth: Avoid unbounded while loops")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before passing the result of skb_to_sgvec() to dma_map_sg() check if any
error was returned.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of multiple traffic classes support, the number
of available frame queues grew significantly, overly inflating the
debugfs FQ statistics entry. Update it to only show the queues
which are actually in use (i.e. have a non-zero frame counter).
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow metering entries in IEEE 802.1Qci is an optional function for a
flow filtering module. Flow metering is two rates two buckets and three
color marker to policing the frames. This patch only enable one rate one
bucket and in color blind mode. Flow metering instance are as
specified in the algorithm in MEF 10.3 and in Bandwidth Profile
Parameters. They are:
a) Flow meter instance identifier. An integer value identifying the flow
meter instance. The patch use the police 'index' as thin value.
b) Committed Information Rate (CIR), in bits per second. This patch use
the 'rate_bytes_ps' represent this value.
c) Committed Burst Size (CBS), in octets. This patch use the 'burst'
represent this value.
d) Excess Information Rate (EIR), in bits per second.
e) Excess Burst Size per Bandwidth Profile Flow (EBS), in octets.
And plus some other parameters. This patch set EIR/EBS default disable
and color blind mode.
v1->v2 changes:
- Use div_u64() as division replace the '/' report:
All errors (new ones prefixed by >>):
ld: drivers/net/ethernet/freescale/enetc/enetc_qos.o: in function `enetc_flowmeter_hw_set':
>> enetc_qos.c:(.text+0x66): undefined reference to `__udivdi3'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base on the tc flower offload police action add max frame size by the
parameter 'mtu'. Tc flower device driver working by the IEEE 802.1Qci
stream filter can implement the max frame size filtering. Add it to the
current hardware tc flower stearm filter driver.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we know the xgmac hardware always has a c45
compliant bus, let's try scanning for c22 capable
PHYs first. If we fail to find any, then it will
fall back to c45 automatically.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACPI support for xgmac MDIO bus registration while maintaining
the existing DT support.
The function mdiobus_register() inside of_mdiobus_register(), brings
up all the PHYs on the mdio bus and attach them to the bus.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN tag insertion/extraction offload is correctly
activated at probe time but deactivation of this feature
(i.e. via ethtool) is broken. Toggling works only for
Tx/Rx ring 0 of a PF, and is ignored for the other rings,
including the VF rings.
To fix this, the existing VLAN offload toggling code
was extended to all the rings assigned to a netdevice,
instead of the default ring 0 (likely a leftover from the
early validation days of this feature). And the code was
moved to the common set_features() function to fix toggling
for the VF driver too.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a drop frames counter to tc flower offloading.
Reporting h/w dropped frames is necessary for some actions.
Some actions like police action and the coming introduced stream gate
action would produce dropped frames which is necessary for user. Status
update shows how many filtered packets increasing and how many dropped
in those packets.
v2: Changes
- Update commit comments suggest by Jiri Pirko.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tlen field into struct tso_t, and change tso_start()
to return skb_transport_offset(skb) + tso->tlen
This removes from callers the need to use tcp_hdrlen(skb) and
will ease UDP segmentation offload addition.
v2: calls tso_start() earlier in otx2_sq_append_tso() [Jakub]
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The replacement of <asm/pgrable.h> with <linux/pgtable.h> made the include
of the latter in the middle of asm includes. Fix this up with the aid of
the below script and manual adjustments here and there.
import sys
import re
if len(sys.argv) is not 3:
print "USAGE: %s <file> <header>" % (sys.argv[0])
sys.exit(1)
hdr_to_move="#include <linux/%s>" % sys.argv[2]
moved = False
in_hdrs = False
with open(sys.argv[1], "r") as f:
lines = f.readlines()
for _line in lines:
line = _line.rstrip('
')
if line == hdr_to_move:
continue
if line.startswith("#include <linux/"):
in_hdrs = True
elif not moved and in_hdrs:
moved = True
print hdr_to_move
print line
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net/sch_generic.h does not need to be included, remove it.
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leave congestion group taildrop enabled for all traffic classes
when PFC is enabled. Notification threshold is low enough such
that it will be hit first and this also ensures that FQs on
traffic classes which are not PFC enabled won't drain the buffer
pool.
FQ taildrop threshold is kept disabled as long as any form of
flow control is on. Since FQ taildrop works with bytes, not number
of frames, we can't guarantee it will not interfere with the
congestion notification mechanism for all frame sizes.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in dpaa2-eth for PFC (Priority Flow Control)
through the DCB ops.
Instruct the hardware to respond to received PFC frames.
Current firmware doesn't allow us to selectively enable PFC
on the Rx side for some priorities only, so we will react to
all incoming PFC frames (and stop transmitting on the traffic
classes specified in the frame).
Also, configure the hardware to generate PFC frames based on Rx
congestion notifications. When a certain number of frames accumulate in
the ingress queues corresponding to a traffic class, priority flow
control frames are generated for that TC.
The number of PFC traffic classes available can be queried through
lldptool. Also, which of those traffic classes have PFC enabled is also
controlled through the same dcbnl_rtnl_ops callbacks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
