Introduce a new .serdes_irq_mapping operation to prepare the
abstraction of IRQ mapping from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mv88e6xxx SERDES code checks for negative error code from
irq_find_mapping, while this function returns an unsigned integer. This
patch removes this dead code and simply returns 0 is no IRQ is found.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352_serdes_irq_link helper is not checking for any error that
may occur during hardware accesses. Worst, the "up" boolean is set from
the potentially unused "status" variable, if read operations failed.
As done in mv88e6390_serdes_irq_link_sgmii, return right away and do
not call dsa_port_phylink_mac_change if an error occurred.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now mv88e6xxx does not enable its ports at setup itself and let
the DSA core handle this, unused ports are disabled without being
powered on first. While that is expected, the SERDES powering code
was assuming that a port was already set up before powering it down,
resulting in freeing an unused IRQ. The patch fixes this assumption.
Fixes: b759f528ca ("net: dsa: mv88e6xxx: enable SERDES after setup")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow-up patch for commit 7a3007d22e ("net: dsa:
mv88e6xxx: fully support SERDES on Topaz family").
Since .port_set_cmode is only called from mv88e6xxx_port_setup_mac and
mv88e6xxx_phylink_mac_config, it is fine to keep this "make writable"
code private to the mv88e6341_port_set_cmode implementation, instead
of adding yet another operation to the switch info structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow-up patch for commit 17deaf5cb3 ("net: dsa:
mv88e6xxx: create serdes_get_lane chip operation").
The .serdes_get_lane implementations access the CMODE of a port,
even though it is cached at the moment, it is safer to call them
after the mutex is locked, not before.
At the same time, check for an eventual error and return IRQ_DONE,
instead of blindly ignoring it.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we support SERDES on the Topaz family in a limited way: no
IRQs and the cmode is not writable, thus the mode is determined by
strapping pins.
Marvell's examples though show how to make cmode writable on port 5 and
support SGMII autonegotiation. It is done by writing hidden registers,
for which we already have code.
This patch adds support for making the cmode for the SERDES port
writable on the Topaz family, via a new chip operation,
.port_set_cmode_writable, which is called from mv88e6xxx_port_setup_mac
just before .port_set_cmode.
SERDES IRQs are also enabled for Topaz.
Tested on Turris Mox.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic update. We are removing the last underscore from
macros MV88E6XXX_PORT_STS_CMODE_100BASE_X and
MV88E6XXX_PORT_STS_CMODE_1000BASE_X. The 2500base-x version does not
have that underscore. Also PHY_INTERFACE_MODE_ macros do not have it
there.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By adding an additional serdes_get_lane implementation (for Topaz), we
can merge the implementations of other SERDES functions (powering and
IRQs). We can skip checking port numbers, since the serdes_get_lane()
methods inform if there is no lane on a port or if the lane cannot be
used for given cmode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a serdes_get_lane() method in the mv88e6xxx operations structure.
Use it instead of calling the different implementations.
Also change the methods so that their return value is used only for
error. The lane number is put into a place referred to by a pointer
given as argument. If the port does not have a lane, return -ENODEV.
Lanes are phy addresses, so use u8 as their type.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the functions operating on the hidden debug registers
into it's own file, port_hidden.c. The functions prefix is renamed from
mv88e6390_hidden_ to mv88e6xxx_port_hidden_, to be consistent with the
rest of this driver. The macros are prefixed with MV88E6XXX_ prefix, and
are changed not to use the BIT() macro nor bit shifts, since the rest of
the port.h file does not use it.
We also add the support for setting the Block Address field when
operating hidden registers. Marvell's mdio examples for SERDES settings
on Topaz use Block Address 0x7 when reading/writing hidden registers,
and although the specification says that block must be set to 0xf, those
settings are reachable only with Block Address 0x7.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390_serdes_irq_link_sgmii IRQ handler reads the SERDES PHY
status register to determine speed, among other things. If cmode of the
port is set to 2500base-x, though, the PHY still reports 1000 Mbps (the
PHY register itself does not differentiate between 1000 Mbps and 2500
Mbps - it thinks it is running at 1000 Mbps, although clock is 2.5x
faster).
Look at the cmode and set SPEED_2500 if cmode is set to 2500base-x.
Also tell mv88e6xxx_port_setup_mac the PHY interface mode corresponding
to current cmode in terms of phy_interface_t.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mv88e6xxx_serdes_power is only called after driver setup,
we can wrap the SERDES IRQ code directly within it for clarity.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SERDES is powered on for CPU and DSA ports and powered down for unused
ports at setup time. But now that DSA calls mv88e6xxx_port_enable
and mv88e6xxx_port_disable for all ports, the SERDES power can now
be handled after setup inconditionally for all ports.
Using the port enable and disable callbacks also have the benefit to
handle the SERDES IRQ for non user ports as well.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling a port, that is not for the driver to decide what to
do with the STP state. This is already handled by the DSA layer.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .port_enable and .port_disable operations are currently only
called for user ports, hence assuming they have a slave device. In
preparation for using these operations for other port types as well,
simply guard all implementations against non user ports and return
directly in such case.
Note that bcm_sf2_sw_suspend() currently calls bcm_sf2_port_disable()
(and thus b53_disable_port()) against the user and CPU ports, so do
not guards those functions. They will be called for unused ports in
the future, but that was expected by those drivers anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_port_setup_mac checks if the requested MAC settings are
different from the current ones, and if not, does nothing (since chaning
them requires putting the link down).
In this check it only looks if the triplet [link, speed, duplex] is
being changed.
This patch adds support to also check if the mode parameter (of type
phy_interface_t) is requested to be changed. The current mode is
computed by the ->port_link_state() method, and if it is different from
PHY_INTERFACE_MODE_NA, we check for equality with the requested mode.
In the implementations of the mv88e6250_port_link_state() method we set
the current mode to PHY_INTERFACE_MODE_NA - so the code does not check
for mode change on 6250.
In the mv88e6352_port_link_state() method, we use the cached cmode of
the port to determine the mode as phy_interface_t (and if it is not
enough, eg. for RGMII, we also look at the port control register for
RX/TX timings).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_smi_direct_wait routine is used to wait on indirect
registers access. It is of no exception and must delay between read
attempts, like other wait routines.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mv88e6xxx_smi_direct_wait function is only used to check
the 16th bit of the (16-bit) SMI Command register. But the bit shift
operation is not enough if we eventually use this function to check
other bits, thus replace it with a mask.
Fixes: e7ba0fad9c ("net: dsa: mv88e6xxx: refine SMI support")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have proper Wait Bit and Wait Mask routines, remove the
unused mv88e6xxx_wait routine and its Global 1 and Global 2 variants.
The indirect tables such as the Device Mapping Table or Priority
Override Table make use of an Update bit to distinguish reading (0)
from writing (1) operations. After a write operation occurs, the bit
self clears right away so there's no need to wait on it. Thus keep
things simple and remove the mv88e6xxx_update helper as well.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVB is not an indirect table using an Update bit, but a unit using
a Busy bit. This means that we must ensure that this bit is cleared
before setting it and wait until it gets cleared again after writing
an operation. Reflect that.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many portions of the driver need to wait until a given bit is set
or cleared. Some busses even have a specific implementation for this
operation. In preparation for such variant, implement a generic Wait
Bit routine that can be used by the driver core functions.
This allows us to get rid of the custom implementations we may find
in the driver. Note that for the EEPROM bits, BUSY and RUNNING bits
are independent, thus it is more efficient to wait independently for
each bit instead of waiting for their mask.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mv88e6xxx_wait routine is used to wait for a given mask
to be cleared to zero. However in some cases, the driver may have
to wait for a given mask to be of a certain non-zero value.
Thus provide a generic wait mask routine that will be used to implement
the current mv88e6xxx_wait function, and use it to wait for 88E6185
PPU states.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPU state of 88E6185 can be either "Disabled at Reset" or
"Disabled after Initialization". Because we intentionally clear the
PPU Enabled bit before checking its state, it is safe to wait for the
MV88E6185_G1_STS_PPU_STATE_DISABLED state explicitly instead of waiting
for any state different than MV88E6185_G1_STS_PPU_STATE_POLLING.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to drop the adjust_link callback in order to finally migrate to
phylink.
Otherwise we get the following warning during startup:
"mv88e6xxx 2188000.ethernet-1:10: Using legacy PHYLIB callbacks. Please
migrate to PHYLINK!"
The warning is generated in the function dsa_port_link_register_of in
dsa/port.c:
int dsa_port_link_register_of(struct dsa_port *dp)
{
struct dsa_switch *ds = dp->ds;
if (!ds->ops->adjust_link)
return dsa_port_phylink_register(dp);
dev_warn(ds->dev,
"Using legacy PHYLIB callbacks. Please migrate to PHYLINK!\n");
[...]
}
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds PTP support for the MV88E6250 family.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is done for all the other structs within this driver.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6250 family doesn't support the MV88E6XXX_PORT_CTL1_MESSAGE_PORT
bit.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this it is possible to mark certain chip ports as invalid. This is
required for example for the MV88E6220 (which is in general a MV88E6250
with 7 ports) but the ports 2-4 are not routed to pins.
If a user configures an invalid port, an error is returned.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6220 is almost the same as MV88E6250 except that the ports 2-4 are
not routed to pins. So the usable ports are 0, 1, 5 and 6.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read and
_mv88e6xxx_port_vlan_add is the only function requiring the preparation
of a new VLAN entry.
To simplify things up, remove the mv88e6xxx_vtu_get wrapper and
explicit the VLAN lookup in _mv88e6xxx_port_vlan_add. This rework
also avoids programming the broadcast entries again when changing a
port's membership, e.g. from tagged to untagged.
At the same time, rename the helper using an old underscore convention.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read.
Explicit the call to mv88e6xxx_vtu_getnext in _mv88e6xxx_port_vlan_del
and the return value expected by switchdev in case of software VLANs.
At the same time, rename the helper using an old underscore convention.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_vtu_getnext is simple enough to call it directly in the
mv88e6xxx_port_db_load_purge function and explicit the return code
expected by switchdev for software VLANs when an hardware VLAN does
not exist.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_vtu_getnext interprets two members from the input
mv88e6xxx_vtu_entry structure: the (excluded) vid member to start
the iteration from, and the valid argument specifying whether the VID
must be written or not (only required once at the start of a loop).
Explicit the assignation of these two fields right before calling
mv88e6xxx_vtu_getnext, as it is done in the mv88e6xxx_vtu_get wrapper.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lock the mutex in the mv88e6xxx_port_vlan_prepare function
called by the DSA stack, instead of doing it in the internal
mv88e6xxx_port_check_hw_vlan helper.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the define here makes the code more expressive.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have an ERPS (Ethernet Ring Protection Switching) setup involving
mv88e6250 switches which we're in the process of switching to a BSP
based on the mainline driver. Breaking any link in the ring works as
expected, with the ring reconfiguring itself quickly and traffic
continuing with almost no noticable drops. However, when plugging back
the cable, we see 5+ second stalls.
This has been tracked down to the userspace application in charge of
the protocol missing a few CCM messages on the good link (the one that
was not unplugged), causing it to broadcast a "signal fail". That
message eventually reaches its link partner, which responds by
blocking the port. Meanwhile, the first node has continued to block
the port with the just plugged-in cable, breaking the network. And the
reason for those missing CCM messages has in turn been tracked down to
the VTU apparently being too busy servicing load/purge operations that
the normal lookups are delayed.
Initial state, the link between C and D is blocked in software.
_____________________
/ \
| |
A ----- B ----- C *---- D
Unplug the cable between C and D.
_____________________
/ \
| |
A ----- B ----- C * * D
Reestablish the link between C and D.
_____________________
/ \
| |
A ----- B ----- C *---- D
Somehow, enough VTU/ATU operations happen inside C that prevents
the application from receving the CCM messages from B in a timely
manner, so a Signal Fail message is sent by C. When B receives
that, it responds by blocking its port.
_____________________
/ \
| |
A ----- B *---* C *---- D
Very shortly after this, the signal fail condition clears on the
BC link (some CCM messages finally make it through), so C
unblocks the port. However, a guard timer inside B prevents it
from removing the blocking before 5 seconds have elapsed.
It is not unlikely that our userspace ERPS implementation could be
smarter and/or is simply buggy. However, this patch fixes the symptoms
we see, and is a small optimization that should not break anything
(knock wood). The idea is simply to avoid doing an VTU load of an
entry identical to the one already present. To do that, we need to
know whether mv88e6xxx_vtu_get() actually found an existing entry, or
has just prepared a struct mv88e6xxx_vtu_entry for us to load. To that
end, let vlan->valid be an output parameter. The other two callers of
mv88e6xxx_vtu_get() are not affected by this patch since they pass
new=false.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a 1ms delay after reset deactivation. Otherwise the chip returns
bogus ID value. This is observed with 88E6390 (Peridot) chip.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a no-op that simply moves all locking and unlocking of
->reg_lock into trivial helpers. I did that to be able to easily add
some ad hoc instrumentation to those helpers to get some information
on contention and hold times of the mutex. Perhaps others want to do
something similar at some point, so this frees them from doing the
'sed -i' yoga, and have a much smaller 'git diff' while fiddling.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment is correct, but the code ends up moving the bits four
places too far, into the VTUOp field.
Fixes: bec8e57252 (net: dsa: mv88e6xxx: implement vtu_getnext and vtu_loadpurge for mv88e6250)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment is correct, but the code ends up moving the bits four
places too far, into the VTUOp field.
Fixes: 11ea809f1a (net: dsa: mv88e6xxx: support 256 databases)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA ports must flood unknown unicast and multicast, but the switch
must not flood the CPU ports with unknown multicast, as this results
in a lot of undesirable traffic that the network stack needs to filter
in software.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a port FDB dump operation, the mutex protecting the concurrent
access to the switch registers is currently held by the internal
mv88e6xxx_port_db_dump and mv88e6xxx_port_db_dump_fid helpers.
It must be held at the higher level in mv88e6xxx_port_fdb_dump which
is called directly by DSA through ds->ops->port_fdb_dump. Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.
2) Read SFP eeprom in max 16 byte increments to avoid problems with
some SFP modules, from Russell King.
3) Fix UDP socket lookup wrt. VRF, from Tim Beale.
4) Handle route invalidation properly in s390 qeth driver, from Julian
Wiedmann.
5) Memory leak on unload in RDS, from Zhu Yanjun.
6) sctp_process_init leak, from Neil HOrman.
7) Fix fib_rules rule insertion semantic change that broke Android,
from Hangbin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
net: aquantia: fix wol configuration not applied sometimes
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
net: rds: fix memory leak when unload rds_rdma
ipv6: fix the check before getting the cookie in rt6_get_cookie
ipv4: not do cache for local delivery if bc_forwarding is enabled
s390/qeth: handle error when updating TX queue count
s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
s390/qeth: check dst entry before use
s390/qeth: handle limited IPv4 broadcast in L3 TX path
net: fix indirect calls helpers for ptype list hooks.
net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
udp: only choose unbound UDP socket for multicast when not in a VRF
net/tls: replace the sleeping lock around RX resync with a bit lock
...
The new mv88e6250_g1_reset() is identical to mv88e6352_g1_reset() except
for the call of mv88e6352_g1_wait_ppu_polling(), so refactor the 6352
version in term of the 6250 one. No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Marvell 88E6250. I've checked that each
member in the ops-structure makes sense, and basic switchdev
functionality works fine.
It uses the new dual_chip option, and since its port registers start
at SMI address 0x08 or 0x18 (i.e., always sw_addr + 0x08), we need to
introduce a new compatible string in order for the auto-identification
in mv88e6xxx_detect() to work.
The chip has four per port 16-bits statistics registers, two of which
correspond to the existing "sw_in_filtered" and "sw_out_filtered" (but
at offsets 0x13 and 0x10 rather than 0x12 and 0x13, because why should
this be easy...). Wiring up those four statistics seems to require
introducing a STATS_TYPE_PORT_6250 bit or similar, which seems a tad
ugly, so for now this just allows access to the STATS_TYPE_BANK0 ones.
The chip does have ptp support, and the existing
mv88e6352_{gpio,avb,ptp}_ops at first glance seem like they would work
out-of-the-box, but for simplicity (and lack of testing) I'm eliding
this.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6250 has a rather different way of reporting the link, speed
and duplex status. A simple difference is that the link bit is bit 12
rather than bit 11 of the port status register.
It gets more complicated for speed and duplex, which do not have
separate fields. Instead, there's a four-bit PortMode field, and
decoding that depends on whether it's a phy or mii port. For the phy
ports, only four of the 16 values have defined meaning; the rest are
called "reserved", so returning {SPEED,DUPLEX}_UNKNOWN seems
reasonable.
For the mii ports, most possible values are documented (0x3 and 0x5
are reserved), but I'm unable to make sense of them all. Since the
bits simply reflect the Px_MODE[3:0] configuration pins, just support
the subset that I'm certain about. Support for other setups can be
added later.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data sheet also mentions the possibility of selecting 200 Mbps for
the MII ports (ports 5 and 6) by setting the ForceSpd field to
0x2 (aka MV88E6065_PORT_MAC_CTL_SPEED_200). However, there's a note
that "actual speed is determined by bit 8 above", and flipping back a
page, one finds that bits 13:8 are reserved...
So without further information on what bit 8 means, let's stick to
supporting just 10 and 100 Mbps on all ports.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6352_G2_WDOG_CTL_* bits almost, but not quite, describe the
watchdog control register on the mv88e6250. Among those actually
referenced in the code, only QC_ENABLE differs (bit 6 rather than bit
5).
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are almost identical to the 6185 variants, but have fewer bits
for the FID.
Bit 10 of the VTU_OP register (offset 0x05) is the VidPolicy bit,
which one should probably preserve in mv88e6xxx_g1_vtu_op(), instead
of always writing a 0. However, on the 6352 family, that bit is
located at bit 12 in the VTU FID register (offset 0x02), and is always
unconditionally cleared by the mv88e6xxx_g1_vtu_fid_write()
function.
Since nothing in the existing driver seems to know or care about that
bit, it seems reasonable to not add the boilerplate to preserve it for
the 6250 (which would require adding a chip-specific vtu_op function,
or adding chip-quirks to the existing one).
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the currently supported chips have .num_databases either 256 or
4096, so this patch does not change behaviour for any of those. The
mv88e6250, however, has .num_databases == 64, and it does not put the
upper two bits in ATU control 13:12, but rather in ATU Operation
9:8. So change the logic to prepare for supporting mv88e6250.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88e6250 (as well as 6220, 6071, 6070, 6020) do not support
multi-chip (indirect) addressing. However, one can still have two of
them on the same mdio bus, since the device only uses 16 of the 32
possible addresses, either addresses 0x00-0x0F or 0x10-0x1F depending
on the ADDR4 pin at reset [since ADDR4 is internally pulled high, the
latter is the default].
In order to prepare for supporting the 88e6250 and friends, introduce
mv88e6xxx_info::dual_chip to allow having a non-zero sw_addr while
still using direct addressing.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite a few of the existing supported chips that use
mv88e6085_g1_ieee_pri_map as ->ieee_pri_map (including, incidentally,
mv88e6085 itself) actually have a reset value of 0xfa50 in the
G1_IEEE_PRI register.
The data sheet for the mv88e6095, however, does describe a reset value
of 0xfa41.
So rather than changing the value in the existing callback, introduce
a new variant with the 0xfa50 value. That will be used by the upcoming
mv88e6250, and existing chips can be switched over one by one,
preferably double-checking both the data sheet and actual hardware in
each case - if anybody actually feels this is important enough to
care.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g1_stats_wait has no users outside global1.c, so make it
static.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macros have an extraneous '800' (after 0180C2 there should be just
six nibbles, with X representing one), while the comments have
interchanged c2 and 80 and an extra :00.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When non-bridged, non-vlan'ed mv88e6xxx port is moving down, error
message is logged:
failed to kill vid 0081/0 for device eth_cu_1000_4
This is caused by call from __vlan_vid_del() with vin set to zero, over
call chain this results into _mv88e6xxx_port_vlan_del() called with
vid=0, and mv88e6xxx_vtu_get() called from there returns -EINVAL.
On symmetric path moving port up, call goes through
mv88e6xxx_port_vlan_prepare() that calls mv88e6xxx_port_check_hw_vlan()
that returns -EOPNOTSUPP for zero vid.
This patch changes mv88e6xxx_vtu_get() to also return -EOPNOTSUPP for
zero vid, then this error code is explicitly cleared in
dsa_slave_vlan_rx_kill_vid() and error message is no longer logged.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Currently, the upper half of a 4-byte STATS_TYPE_PORT statistic ends
up in bits 47:32 of the return value, instead of bits 31:16 as they
should.
Fixes: 6e46e2d821 ("net: dsa: mv88e6xxx: Fix u64 statistics")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Marvell SOHO switches have several ways to access the internal
registers. One of them being the System Management Interface (SMI),
using the MDC and MDIO pins, with direct and indirect variants.
In preparation for adding support for other register accesses, move
the SMI code into its own files. At the same time, refine the code
to make it clear that the indirect variant is implemented using the
direct variant accessing only two registers for command and data.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NO_CPU strap is set, the switch starts in 'dumb hub' mode, with
all ports enable. Ports which are then actively used are reconfigured
as required when the driver starts. However unused ports are left
alone. Change this to disable them, and turn off any SERDES
interface. This could save some power and so reduce the temperature a
bit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When requested to disable a port, set the port STP state to disabled.
This fully disables the port and should save some power.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the legacy method of probing the mv88e6xxx driver, now that all
the mainline boards have been converted to use mdio based probing for
a number of cycles.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink will call the mac_config() callback once per second when
polling a PHY or a fixed link. The MAC driver is not supposed to
reconfigure the MAC if nothing has changed.
Make the mv88e6xxx driver look at the current configuration of the
port, and return early if nothing has changed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes few issues in mv88e6390x_port_set_cmode().
1. When entering the function the old cmode may be 0, in this case
mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
out and have no chance to set a new mode. Therefore deal properly
with -ENODEV.
2. Once we have disabled power and irq, let's set the cached cmode to 0.
This reflects the actual status and is cleaner if we bail out with an
error in the following function calls.
3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
Currently we set the cached mode to the new one at the very end of
the function only, means until then we use the old one what may be
wrong.
4. When calling mv88e6390_serdes_irq_enable() we use the lane value
belonging to the old cmode. Get the lane belonging to the new cmode
before calling this function.
It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.
Fixes: d235c48b40 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This partially reverts ed8fe20205 ("net: dsa: mv88e6xxx: prevent
interrupt storm caused by mv88e6390x_port_set_cmode"). I missed
that chip->ports[].cmode is overwritten anyway by the cmode
caching in mv88e6xxx_setup().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the switch driver is expected to configure CPU and DSA
ports to their maximum speed. For the 6341 and 6390 families, the
ports interface mode has to be configured as well. The 6390X range
support 10G ports using XAUI, while the 6341 and 6390 supports
2500BaseX, as their maximum speed.
Fixes: 787799a9d5 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original patch I missed to add mv88e6xxx_ports_cmode_init()
to the second probe function, the one for the new DSA framework.
Fixes: ed8fe20205 ("net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode")
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an external PHY is connected via SGMII and uses in-band signalling
then the auto-negotiated values aren't propagated to the port,
resulting in a broken link. See discussion in [0]. This patch adds
this propagation. We need to call mv88e6xxx_port_setup_mac(),
therefore export it from chip.c.
Successfully tested on a ZII DTU with 88E6390 switch and an
Aquantia AQCS109 PHY connected via SGMII to port 9.
[0] https://marc.info/?t=155130287200001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ports 9 and 10 don't have internal PHY's but are (dependent on the
version) SERDES/SGMII/XAUI/RXAUI ports.
v2:
- fix it for all 88E6x90 family members
Fixes: bc3931557d ("net: dsa: mv88e6xxx: Add number of internal PHYs")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing another issue I faced the problem that
mv88e6xxx_port_setup_mac() failed due to DUPLEX_UNKNOWN being passed
as argument to mv88e6xxx_port_set_duplex(). We should handle this case
gracefully and return -EOPNOTSUPP, like e.g. mv88e6xxx_port_set_speed()
is doing it.
Fixes: 7f1ae07b51 ("net: dsa: mv88e6xxx: add port duplex setter")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.
Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c3949 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.
Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.
v2:
- add small helper and init the number of actual ports only
Fixes: 364e9d7776 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.
Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.
This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.
Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.
This was tested on 6390X using RXAUI mode.
Fixes: 364e9d7776 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined. Fix
the combing, which wrongly worked on u16's.
Fixes: 80c4627b27 ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Topaz family should have different phylink_validate method from the
Peridot, since on Topaz the port supporting 2500BaseX mode is port 5,
not 9 and 10.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 787799a9d5 sets the SERDES interfaces of 6390 and 6390X to
1000BaseX, but this is only needed on 6390X, since there are SERDES
interfaces which can be used on lower ports on 6390.
This commit fixes this by returning to previous behaviour on 6390.
(Previous behaviour means that CMODE is not set at all if requested mode
is NA).
This is needed on Turris MOX, where the 88e6190 is connected to CPU in
2500BaseX mode.
Fixes: 787799a9d5 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to hold the register lock while requesting the GPIO
interrupt. By not holding it we can also avoid a false positive
lockdep splat.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following false positive lockdep splat has been observed.
======================================================
WARNING: possible circular locking dependency detected
4.20.0+ #302 Not tainted
------------------------------------------------------
systemd-udevd/160 is trying to acquire lock:
edea6080 (&chip->reg_lock){+.+.}, at: __setup_irq+0x640/0x704
but task is already holding lock:
edff0340 (&desc->request_mutex){+.+.}, at: __setup_irq+0xa0/0x704
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&desc->request_mutex){+.+.}:
mutex_lock_nested+0x1c/0x24
__setup_irq+0xa0/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_probe+0x41c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
-> #0 (&chip->reg_lock){+.+.}:
__mutex_lock+0x50/0x8b8
mutex_lock_nested+0x1c/0x24
__setup_irq+0x640/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_g2_irq_setup+0xcc/0x1b4 [mv88e6xxx]
mv88e6xxx_probe+0x44c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&desc->request_mutex);
lock(&chip->reg_lock);
lock(&desc->request_mutex);
lock(&chip->reg_lock);
&desc->request_mutex refer to two different mutex. #1 is the GPIO for
the chip interrupt. #2 is the chained interrupt between global 1 and
global 2.
Add lockdep classes to the GPIO interrupt to avoid this.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not specifying an explicit format argument but instead passing a
string litteral which causes these two warnings to show up:
drivers/net/dsa/mv88e6xxx/chip.c: In function
'mv88e6xxx_irq_poll_setup':
drivers/net/dsa/mv88e6xxx/chip.c:483:2: warning: format not a string
literal and no format arguments [-Wformat-security]
chip->kworker = kthread_create_worker(0, dev_name(chip->dev));
^~~~
drivers/net/dsa/mv88e6xxx/ptp.c: In function 'mv88e6xxx_ptp_setup':
drivers/net/dsa/mv88e6xxx/ptp.c:403:4: warning: format not a string
literal and no format arguments [-Wformat-security]
dev_name(chip->dev));
^~~~~~~~
LD [M] drivers/net/dsa/mv88e6xxx/mv88e6xxx.o
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the bridge flags to Marvell 88e6xxx bridges, allowing
the multicast and unicast flood properties to be controlled. These
can be controlled on a per-port basis via commands such as:
bridge link set dev lan1 flood on|off
bridge link set dev lan1 mcast_flood on|off
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge. When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.
I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are
directly cleared by reading the Global 1 status register. However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.
The code only services interrupts whose status bit is set at the time of reading its status
register. If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.
This is not a problem with polling or level interrupts since the handler will be called
again to process the event. However, it's a big problem when using level interrupts.
The fix presented here is to add a loop around the code servicing switch interrupts. If
any pending interrupts remain after the current set has been handled, we loop and process
the new set. If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.
Tested on espressobin board.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using an external PHY, ports 9 and 10 can support 2500BaseT.
So set this link mode in the mask when validating.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
On one hand, the mv88e6xxx driver has a work queue called in loop
which will attempt register accesses after MDIO bus suspension, that
entirely freezes the platform during suspend.
On the other hand, the DSA core is not ready yet to support suspend to
RAM operation because so far there is no way to recover reliably the
switch configuration.
To avoid the kernel to freeze when suspending with a switch driven by
the mv88e6xxx driver, we choose to prevent the driver suspension and
in the same way, the whole platform.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU port vector contains a bit per port of the switch. The code
wrongly used it as a port number, and incremented a port counter. This
resulted in the wrong interfaces counter being incremented, and
potentially going off the end of the array of ports.
Fix this by using the source port ID for the violation, which really
is a port number.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Tested-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 65f60e4582 ("net: dsa: mv88e6xxx: Keep ATU/VTU violation statistics")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duec to a typo, mv88e6390_serdes_irq_setup() calls itself, rather than
mv88e6390x_serdes_irq_setup(). It then blows the stack, and shortly
after the machine blows up.
Fixes: 2defda1f4b ("net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390X")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6320 family of switches uses the same watchdog registers as the
6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ethtool_regs version is set to 0 for all DSA drivers.
Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have a workaround for a couple of switches whose internal
PHYs only have the Marvel OUI, but no model number. We detect such
PHYs and give them the 6390 ID as the model number. However the
mv88e6161 has two SERDES interfaces in the same address range as its
internal PHYs. These suffer from the same problem, the Marvell OUI,
but no model number. As a result, these SERDES interfaces were getting
the same PHY ID as the mv88e6390, even though they are not PHYs, and
the Marvell PHY driver was trying to drive them.
Add a special case to stop this from happen.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10
to support up to 10Gbps using 4 SERDES interfaces. However, when lower
speeds are used, which need fewer SERDES interfaces, the unused SERDES
interfaces can be used by ports 2-8.
The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces
assigned to them. This only gets changed when the interface is
configured after what the SFP supports has been determined, or the 10G
PHY completes auto-neg.
For hardware designs which limit ports 9 and 10 to one or two SERDES
interfaces, and place SFPs on the lower interfaces, this is too
late. Those ports with SFP should not wait until ports 9/10 are up in
order to get access to the SERDES interface. So change the default
configuration when the driver is initialised. Configure ports 9 and 10
to 1000BaseX, so they use a single SERDES interface, freeing up the
others. They can steal them back if they need them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for the port_set_speed method for the Topaz family.
Currently the same method is used as for the Peridot family, but
this is wrong for the SERDES port.
On Topaz, the SERDES port is port 5, not 9 and 10 as in Peridot.
Moreover setting alt_bit on Topaz only makes sense for port 0 (for
(differentiating 100mbps vs 200mbps). The SERDES port does not
support more than 2500mbps, so alt_bit does not make any difference.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a cut/paste error and a typo which results in ATU miss violations
not being reported.
Fixes: 0977644c50 ("net: dsa: mv88e6xxx: Decode ATU problem interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6xxx can have external PHYs attached to certain ports and those
PHYs could even be on different MDIO bus than the one within the switch.
This patch makes sure that ports with such PHYs are configured correctly
according to the information provided by the PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6352 family has one SERDES interface, which can be used by either
port 4 or port 5. Add interrupt support for the SERDES interface, and
report when the link status changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After changing to the needed page, actually write the value to the
register!
Fixes: 09cb7dfd3f ("net: dsa: mv88e6xxx: describe PHY page and SerDes")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards the interrupt can be shared between multiple devices.
For example on Turris Mox the interrupt is shared between all switches.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added a new error path, but we need to drop the lock before we return.
Fixes: 2d2e1dd299 ("net: dsa: mv88e6xxx: Cache the port cmode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to test if these flags are set but there are some && vs &
typos.
Fixes: efd1ba6af9 ("net: dsa: mv88e6xxx: Add SERDES phydev_mac_change up for 6390")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port changes CMODE, the SERDES interface being used can change.
Disable interrupts for the old SERDES interface, and enable interrupts
on the new.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink wants to know when the MAC layers notices a change in the
link. For the 6390 family, this is a change in the SERDES state.
Add interrupt support for the SERDES interface used to implement
SGMII/1000Base-X/2500Base-X. This is currently limited to ports 9 and
10. Support for the 10G SERDES and other ports will be added later,
building on this basic framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An up coming change will register interrupts for individual switch
ports, using the mv88e6xxx_port as the interrupt context information.
Add members to the mv88e6xxx_port structure so we can link it back to
the mv88e6xxx_chip member the port belongs to and the port number of
the port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family has a number of SERDES interfaces per port. When the
cmode changes, eg 1000Base-X to XAUI, the SERDES interface in use will
also change. Power down the old SERDES interface and power up the new
SERDES interface.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ports CMODE indicates the type of link between the MAC and the
PHY. It is used often in the SERDES code. Rather than read it each
time, cache its value.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 has three different SERDES interface types. 2500Base-X is
implemented by the SGMII/1000Base-X SERDES. So power on/off the
correct SERDES.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for accessing SERDES registers of the 6390 family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a need to add more functions manipulating the SERDES
interfaces. Cleanup the namespace.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 has two SERDES interfaces, used by ports 9 and 10. The 6390X
has eight SERDES interfaces. These allow ports 9 and 10 to do 10G. Or
if lower speeds are used, some of the SERDES interfaces can be used by
ports 2-8 for 1000Base-X.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family has 8 SERDES lanes. What ports use these lanes depends
on how ports 9 and 10 are configured. If 9 and 10 does not make use of
a line, one of the lower ports can use it.
Add a function to return the lane a port is using, if any, and simplify
the code to power up/down the lane.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rudimentary phylink support to mv88e6xxx.
TODO:
- needs to call phylink_mac_change() when the port link comes up/goes down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6185 can enable/disable 802.3z pause be setting the MyPause bit in
the port status register. Add an op to support this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Version 1 of the patch adding SERDES support to the 88E6141/6341
correctly added the ops to the 88E6141/6341. However, by the time
version 3 was committed, the ops had moved to the 88E6085/6175. Put
them back where they belong.
Fixes: 5bafeb6e7e ("net: dsa: mv88e6xxx: 88E6141/6341 SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
free_irq() waits until all handlers for this IRQ have completed. As the
relevant handler (mv88e6xxx_g1_irq_thread_fn()) takes the chip's reg_lock
it might never return if the thread calling free_irq() holds this lock.
For the same reason kthread_cancel_delayed_work_sync() in the polling case
must not hold this lock.
Also first free the irq (or stop the worker respectively) such that
mv88e6xxx_g1_irq_thread_work() isn't called any more before the irq
mappings are dropped in mv88e6xxx_g1_irq_free_common() to prevent the
worker thread to call handle_nested_irq(0) which results in a NULL-pointer
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For slow processors using bit-banging MDIO, 20ms can be too short a
timeout when waiting for the transmit timestamp to become
available. Double it to 40ms.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the 6352 and newer switches, the PTP Ethertype defaults to
ETH_P_1588. Hence it was not explicitly set. The 6165 however defaults
to 0. So explicitly set the EtherType.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 family supports a more restricted version of hardware time
stamps. Only L2 PTP is supported. All ports have to use the same
EtherType, and transport spec configuration. PTP can only be
enabled/disabled globally, not per port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 only supports layer L2 PTP, where as the more modern devices
also support UDP and UDPv6, i.e. L4. Abstract the supported receive
filters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 family does not have per port PTP control registers. Also, it
places the timestamp data in different registers. Abstract the current
implementation of 6352 compatible PTP devices so that 6165 can be
added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family has its global clock in the PTP global
registers. It does not support any form of PTP events. Add a function
to read the clock, fill in an ops structure, and register it with the
two members of the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6165 PTP registers are all in AVB bank F, unlike newer
generations which spread them over AVB bank E and F. Implement AVB ops
for the MV88E6165 which hides this difference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family supports PTP, but its registers use a different
layout to the currently supported devices. Abstract accessing the PTP
registers into a set of ops, so making space for a second
implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it explicit that either device tree is used or platform data. If
neither is available, abort the probe.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 877b7cb0b6 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mv88e6xxx_probe(), ("np" or "pdata") might be an invariant
but GCC can't see that, therefore:
drivers/net/dsa/mv88e6xxx/chip.c: In function ‘mv88e6xxx_probe’:
drivers/net/dsa/mv88e6xxx/chip.c:4420:13: warning: ‘compat_info’ may be used uninitialized in this function [-Wmaybe-uninitialized]
chip->info = compat_info;
Actually, it should have warned on the "if (!compat_info)" test, but
whatever.
Explicitly initialize to NULL in the variable declaration to
deal with this.
Fixes: 877b7cb0b6 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the size of the EEPROM to the platform data, so it can also be
instantiated by a platform device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all the world uses device tree. Some parts of the world still use
platform devices and platform data. Add basic support for probing a
Marvell switch via platform data.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IRQ domain will work without an OF node. It is not possible to
reference interrupts via a phandle, but C code can still use
irq_find_mapping() to get an interrupt from the domain.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
