The A10/A20 Allwinner SoCs have two camera sensor interface blocks,
named CSI0 and CSI1. The two have the same register layouts with
slightly different features:
- CSI0 has an image signal processor (ISP); CSI1 doesn't
- CSI0 can support up to four separate channels under CCIR656;
CSI1 can only support one
- CSI0 can support up to 16-bit wide bus with YUV422;
CSI1 can support up to 24-bit wide bus with YUV444
For now the driver doesn't support wide busses, nor CCIR656. So the
only relevant difference is whether a clock needs to be taken and
enabled for the ISP.
Add structs to record the differences, tie them to the compatible
strings, and deal with the ISP clock. Support for the new CSI1
hardware block is added as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On Allwinner SoCs, some high memory bandwidth devices do DMA directly
over the memory bus (called MBUS), instead of the system bus. These
devices include the CSI camera sensor interface, video (codec) engine,
display subsystem, etc.. The memory bus has a different addressing
scheme without the DRAM starting offset.
Deal with this using the "interconnects" property from the device tree,
or if that is not available, set dev->dma_pfn_offset to PHYS_PFN_OFFSET.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Allwinner camera sensor interface has a different definition of
[HV]sync. While the timing diagram uses the names HSYNC and VSYNC,
the note following the diagram and register names use HREF and VREF.
Combined they imply the hardware uses either [HV]REF or inverted
[HV]SYNC. There are also registers to set horizontal skip lengths
in pixels and vertical skip lengths in lines, also known as back
porches.
Fix the polarity handling by using the opposite polarity flag for
the checks. Also rename `[hv]sync_pol` to `[hv]ref_pol` to better
match the hardware register description.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CLK_POL field specifies whether data is sampled on the falling or
rising edge of PCLK, not whether the data lines are active high or low.
Evidence of this can be found in the timing diagram labeled "horizontal
size setting and pixel clock timing".
Fix the setting by checking the correct flag, V4L2_MBUS_PCLK_SAMPLE_RISING.
While at it, reorder the three polarity flag checks so HSYNC and VSYNC
are grouped together.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The omap3isp driver set the new buffer and enabled the CCDC in a situation
a new buffer was available but streaming was about to be stopped on the
CCDC. This lead to frequent system crashes in case there were buffers
queued when streming was being stopped.
Fix this by first checking whether there's an intent to stop streaming and
if there isn't, then set the new buffer and re-enable CCDC.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The isp was marked to have failed to stop if stopping streaming on an
external subdev failed. The return value from the external subdev should
be ignored instead as it is not part of the ISP and thus the ISP does not
need to be reset for that reason.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
-----BEGIN PGP SIGNATURE-----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=b15X
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-12-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
The v4l2-compliance tests failed with the touch device when multiplanar was
enabled in vivid. Since it is perfectly fine to support the multiplanar API
for touch, add support for this in vivid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_buffer's 'field' value was never initialized in vivid for the
touch capture device, causing v4l2-compliance errors.
Set it to NONE.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the sink pad of scaler subdevice to respond
VIDIOC_G_SELECTION and VIDIOC_S_SELECTION ioctls with the following
targets: V4L2_SEL_TGT_COMPOSE_BOUNDS and V4L2_SEL_TGT_CROP.
* Add new const struct crop_rect_default to initialize subdev scaler
properly.
* Make changes in sink pad format reflect to the crop rectangle. E.g.
changing the frame format to a smaller size one can make the former
crop rectangle selects a non existing frame area. To solve this
situation the crop rectangle is clamped to the frame boundaries.
* Clamp crop rectangle respecting the sink bounds during set_selection
ioctl.
Co-developed-by: Danilo Figueiredo Rocha <drocha.figueiredo@gmail.com>
Signed-off-by: Guilherme Alcarde Gallo <gagallo7@gmail.com>
Signed-off-by: Danilo Figueiredo Rocha <drocha.figueiredo@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MediaTek encoder allocates non pixel data area for an input buffer every
plane. As the input buffer should be read-only, the driver should not write
anything in the buffer. Therefore, the extra data should be unnecessary.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When requesting format from sensor, some sensors call the
subdev_get_try_crop which for ISI was not properly initialized, and this
causes errors in determining proper image resolutions.
To accommodate for this, when trying a format (in try_fmt), first attempt
to obtain the framesize for this format from sensor.
In case this fails, use the maximum ISI width/height as try_crop, otherwise
provide the first size height/width from the sensor.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In try_fmt, properly initialize the pad_cfg variable to zeros.
This can be used by various calls from the subdev, so it's better
to have it initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This adds support for GREY and Y16 formats, based on Y10 mbus codes.
Y16 needs to go through preview path in the ISI, with 2 pixels per word,
and it fits the Y16 format. The ISI data lines need to be MSB aligned with
the sensor data lines.
GREY format in 8 bits per pixel is done by dropping the 2 LSB bits
from the Y10 format, and packed as 4 pixels per word.
Suggested-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When requesting format from sensor, some sensors call the
subdev_get_try_crop which for ISC was not properly initialized, and this
causes errors in determining proper image resolutions.
To accommodate for this, when trying a format (in try_fmt), first attempt
to obtain the framesize for this format from sensor.
In case this fails, use the maximum ISC width/height as try_crop, otherwise
provide the first size height/width from the sensor.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With some sensors, the mbus code must match the one that sensor supports.
In this case we should initialize the mbus_code of the fse/fie before
calling the subdev, and not after.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In try_fmt, properly initialize the pad_cfg variable to zeros.
This can be used by various calls from the subdev, so it's better
to have it initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ISC can receive input from sensors using Y10 format directly
(10 bits greyscale). In this case, the ISC must dump the data directly,
either as GREY (8bit) or Y10 (10bit).
Y16 is not supported because we cannot align the MSB 10 bits to the MSB
inside the 16bit container.
For this format, the ISC internal pipeline cannot work (only works with
BAYER), so we must dump the data directly as 8bit/10bit.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case the format that the sensor sends is 8 bit only (like GREY for
example) we need to be able to bypass ISC pipeline and directly dump
8 bits.
That's why the hardcoded value of 16 bpp is not correct in all cases.
This change allows the output format to decide what is the correct bpp
(bits per pixel) such that the result is in the proper format.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When decoding using the CODA internal rotator (for example NV12
capture), currently the value vb2_buf.index + CODA_MAX_FRAMEBUFFERS (19)
is written into the DEC_PIC_ROT_INDEX register. At least with firmware
version 3.1.1 this causes CODA hangups as soon as the register value
reaches 32. Instead, always write CODA_MAX_FRAMEBUFFERS.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Both platform_get_irq_byname() and platform_get_irq() already print an
error. Remove the redundant error message.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds JPEG encoding support for CODA960, handling the JPEG
hardware directly. A separate JPEG encoder video device is created due
to the separate hardware unit and different supported pixel formats.
While the hardware can not change subsampling on the fly, it can encode
4:2:2 subsampled images into JPEGs of the same subsampling.
There are two additional tracepoints added to the coda driver that can
be used together with the v4l2:v4l2_qbuf and v4l2:v4l2_dqbuf tracepoints
to to follow video frames through the mem2mem device when encoding or
decoding with the CODA960 JPEG codec:
coda:coda_jpeg_run
coda:coda_jpeg_done
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
[hverkuil-cisco@xs4all.nl: removed unused k and q_data_dst variables]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CODA960 JPEG codec is controlled directly from the host, there is no
support in the BIT processor firmware. This patch adds the necessary
register definitions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Huffman bits tables are always 16 bytes long, and they are always
followed directly by the values tables, both in hardware and in JPEG
files. Just merge the two tables.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Always call finish_run when the hardware signals completion. This
will allow JPEG contexts to clean up even if job_abort was called
during the device_run.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In csc_set_coeff() we were previously checking if the format type was
V4L2_BUF_TYPE_VIDEO_OUTPUT or V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE as a
mean to figure out if the format was multiplanar or not. This was not
entirely accurate as the format type could also be a CAPTURE type
instead.
Fix this by removing the 'switch' construct and replacing them with
"if (V4L2_TYPE_IS_MULTIPLANAR(type))" instead.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver forgets to kill tasklet when probe fails and remove.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Support to emulate touch devices in vivid driver.
It generates touch patterns simulating single tap, double tap, triple
tap, move from left to right, zoom in, zoom out, palm press simulating
large area being pressed on screen, and simulating 16 different
simultaneous touch points.The values generated are based on
behavior of the rmi_f54 driver.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver misses destroying wdt_wq when remove like what is done when
probe fails.
Add the missed calls like what is done to job_wq to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver forgets to call destroy_workqueue when remove and probe fails.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Make sure that both enum_mbus_code() and enum_framesize() properly
populate the .which parameter member, otherwise -EINVAL is return
causing the subdev asynchronous registration handshake to fail.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When start_streaming fails after the buffers have been queued we have to
make sure all buffers are returned to user-space properly otherwise a
v4l2 level WARN is generated.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently we were using an arbitrarily small maximum resolution mostly
based on available sensor capabilities. However the hardware DMA limits
are much higher than the statically define maximum resolution we were
using.
There we rework the boundary check code to handle the maximum width and
height based on the maximum line width in bytes and re-calculating the
pixel width based on the given pixel format.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Because V4L2 still uses a specific way to manage power state of devices
that predates runtime PM, bridge driver should power on and off sub
device explicitly.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the needed control module register bit layout to support the AM654
family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the needed control module register bit layout to support
the DRA76x family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current CSI2 DPHY initialization sequence although
functional does not match with the documented sequence
in the Technical Reference Manual.
This may affect capture re-startability in stop/start
situations.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pixel processing unit was hard coded to only handle 8 bits per pixel
from input to output.
We now add handling for 10, 12 and 16 bits per pixel at the source and
setting the in-memory size (i.e. container size) to 16 bits for these 3
cases.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current method to calculate the ddr clk period is wrong.
Therefore the ths_term calculation is incorrect.
Also it was wrongly assumed that the ths_settle parameter
was based on the control clock instead of the pixel clock.
Since the DPHY can tolerate quite a bit a of variation,
capture was still mostly working with the 2 tested modes
when the pixel clock was close to the control clock
(i.e. 96 Mhz). But it would quickly stops working when
using different modes or when customers used different
sensors altogether.
Calculating the DDRClk period needs to take into account
the pixel bit width and the number of active data lanes.
Based on the latest technical reference manual these
parameters should now be calculated as follows:
THS_TERM: Programmed value = floor(20 ns/DDRClk period)
THS_SETTLE: Programmed value = floor(105 ns/DDRClk period) + 4
Also originally 'depth' was used to represent the number of
bits a pixel would use once stored in memory (i.e. the
container size). To accurately calculate the THS_* parameters
we need to use the actual number of bits per pixels coming
in from the sensor. So we are renaming 'depth' to 'bpp' (bits
per pixels) and update the format table to show the actual
number of bits per pixel being received.
The "container" size will be derived from the "bpp" value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Apply Errata i913 every time the functional clock is enabled.
This should take care of suspend/resume case as well.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When setting DMA for video capture from CSI channel, if the DMA size
is not given, it ends up writing as much data as sent by the camera.
This may lead to overwriting the buffers causing memory corruption.
Observed green lines on the default framebuffer.
Restrict the DMA to maximum height as specified in the S_FMT ioctl.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allow CAL to be able to export DMA buffer.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
First this patch adds a method to access the CTRL_CORE_CAMERRX_CONTROL
register to use the syscon mechanism. For backward compatibility we also
handle using the existing camerrx_control "reg" entry if a syscon node
is not found.
In addition the register bit layout for the CTRL_CORE_CAMERRX_CONTROL
changes depending on the device. In order to support this we need to use
a register access scheme based on data configuration instead of using
static macro.
In this case we make use of the regmap facility and create data set
based on the various device and phy available.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Looks like the preferred macro to define a single bit mask is BIT() and
not BIT_MASK().
Signed-off-by: Benoit Parrot <bparrot@ti.com>
[hverkuil-cisco@xs4all.nl: fix checkpatch warnings for CAL_HL_IRQ_MASK]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Hj7G
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of stuff in here, though it hasn't been too insane this merge
apart from dealing with the security fun.
uapi:
- export different colorspace properties on DP vs HDMI
- new fourcc for ARM 16x16 block format
- syncobj: allow querying last submitted timeline value
- DRM_FORMAT_BIG_ENDIAN defined as unsigned
core:
- allow using gem vma manager in ttm
- connector/encoder/bridge doc fixes
- allow more than 3 encoders for a connector
- displayport mst suspend/resume reprobing support
- vram lazy unmapping, uniform vram mm and gem vram
- edid cleanups + AVI informframe bar info
- displayport helpers - dpcd parser added
dp_cec:
- Allow a connector to be associated with a cec device
ttm:
- pipelining with no_gpu_wait fix
- always keep BOs on the LRU
sched:
- allow free_job routine to sleep
i915:
- Block userptr from mappable GTT
- i915 perf uapi versioning
- OA stream dynamic reconfiguration
- make context persistence optional
- introduce DRM_I915_UNSTABLE Kconfig
- add fake lmem testing under unstable
- BT.2020 support for DP MSA
- struct mutex elimination
- Tigerlake display/PLL/power management improvements
- Jasper Lake PCH support
- refactor PMU for multiple GPUs
- Icelake firmware update
- Split out vga + switcheroo code
amdgpu:
- implement dma-buf import/export without helpers
- vega20 RAS enablement
- DC i2c over aux fixes
- renoir GPU reset
- DC HDCP support
- BACO support for CI/VI asics
- MSI-X support
- Arcturus EEPROM support
- Arcturus VCN encode support
- VCN dynamic powergating on RV/RV2
amdkfd:
- add navi12/14/renoir support to kfd
radeon:
- SI dpm fix ported from amdgpu
- fix bad DMA on ppc platforms
gma500:
- memory leak fixes
qxl:
- convert to new gem mmap
exynos:
- build warning fix
komeda:
- add aclk sysfs attribute
v3d:
- userspace cleanup uapi change
i810:
- fix for underflow in dispatch ioctls
ast:
- refactor show_cursor
mgag200:
- refactor show_cursor
arcgpu:
- encoder finding improvements
mediatek:
- mipi_tx, dsi and partial crtc support for MT8183 SoC
- rotation support
meson:
- add suspend/resume support
omap:
- misc refactors
tegra:
- DisplayPort support for Tegra 210, 186 and 194.
- IOMMU-backed DMA API fixes
panfrost:
- fix lockdep issue
- simplify devfreq integration
rcar-du:
- R8A774B1 SoC support
- fixes for H2 ES2.0
sun4i:
- vcc-dsi regulator support
virtio-gpu:
- vmexit vs spinlock fix
- move to gem shmem helpers
- handle large command buffers with cma"
* tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm: (1855 commits)
drm/amdgpu: invalidate mmhub semaphore workaround in gmc9/gmc10
drm/amdgpu: initialize vm_inv_eng0_sem for gfxhub and mmhub
drm/amd/amdgpu/sriov skip RLCG s/r list for arcturus VF.
drm/amd/amdgpu/sriov temporarily skip ras,dtm,hdcp for arcturus VF
drm/amdgpu/gfx10: re-init clear state buffer after gpu reset
merge fix for "ftrace: Rework event_create_dir()"
drm/amdgpu: Update Arcturus golden registers
drm/amdgpu/gfx10: fix out-of-bound mqd_backup array access
drm/amdgpu/gfx10: explicitly wait for cp idle after halt/unhalt
Revert "drm/amd/display: enable S/G for RAVEN chip"
drm/amdgpu: disable gfxoff on original raven
drm/amdgpu: remove experimental flag for Navi14
drm/amdgpu: disable gfxoff when using register read interface
drm/amdgpu/powerplay: properly set PP_GFXOFF_MASK (v2)
drm/amdgpu: fix bad DMA from INTERRUPT_CNTL2
drm/radeon: fix bad DMA from INTERRUPT_CNTL2
drm/amd/display: Fix debugfs on MST connectors
drm/amdgpu/nv: add asic func for fetching vbios from rom directly
drm/amdgpu: put flush_delayed_work at first
drm/amdgpu/vcn2.5: fix the enc loop with hw fini
...
Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of the
patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs apis
so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over time,
it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules and
have it "just work" for a variety of platforms (like a distro kernel)
The big problem turned out to be a lack of depandancy information
between different areas of DT entries, and the work here resolves that
problem and now allows devices to boot properly, and quicker than a
monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6m6Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yntJQCcCqg6RQ7LTdHuZv1ETeefXlsfk00An1Jtean6
42bWGx52bGFvAcpjWy8R
=P7hq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
* patchwork: (360 commits)
media: Revert "media: mtk-vcodec: Remove extra area allocation in an input buffer on encoding"
media: hantro: Set H264 FIELDPIC_FLAG_E flag correctly
media: hantro: Remove now unused H264 pic_size
media: hantro: Use output buffer width and height for H264 decoding
media: hantro: Reduce H264 extra space for motion vectors
media: hantro: Fix H264 motion vector buffer offset
media: ti-vpe: vpe: fix compatible to match bindings
media: dt-bindings: media: ti-vpe: Document VPE driver
media: zr364xx: remove redundant assigmnent to idx, clean up code
media: Documentation: media: *_DEFAULT targets for subdevs
media: hantro: Fix s_fmt for dynamic resolution changes
media: i2c: Use the correct style for SPDX License Identifier
media: siano: Use the correct style for SPDX License Identifier
media: vicodec: media_device_cleanup was called too early
media: vim2m: media_device_cleanup was called too early
media: cedrus: Increase maximum supported size
media: cedrus: Fix H264 4k support
media: cedrus: Properly signal size in mode register
media: v4l2-ctrl: Lock main_hdl on operations of requests_queued.
media: si470x-i2c: add missed operations in remove
...
This reverts commit 3192b2ca79.
There are indications that this patch causes problems on some
platforms due to some hardware prefetch. Reverting this patch
for now until this is better understood.
Reported-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Update the compatible string to match the updated bindings.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Disable output side crop selections for the decoder.
This fixes the following v4l2-compliance complaint:
fail: v4l2-test-formats.cpp(1576): IS_DECODER(node)
test Cropping: FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Disable capture side compose selections for the encoder.
This fixes the following v4l2-compliance complaint:
fail: v4l2-test-formats.cpp(1662): IS_ENCODER(node)
test Composing: FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MediaTek encoder allocates non pixel data area for an input buffer every
plane. As the input buffer should be read-only, the driver should not write
anything in the buffer. Therefore, the extra data should be unnecessary.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In the implementation of aspeed_video_probe() the allocated memory for
video should be released if either devm_ioremap_resource()
or aspeed_video_init() or aspeed_video_setup_video() fails. Replace
kzalloc() with devm_kzalloc to avoid explicit release for video.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The irqlock spinlock has been unused from the start. Remove it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
v4l2_compat_ioctl32() is the function that calls into
v4l2_file_operations->compat_ioctl32(), so setting that back to the same
function leads to a trivial endless loop, followed by a kernel
stack overrun.
Remove the incorrect assignment.
Cc: stable@vger.kernel.org
Fixes: 7472c1c691 ("[media] media: venus: vdec: add video decoder files")
Fixes: aaaa93eda6 ("[media] media: venus: venc: add video encoder files")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The field kthread_sen in the vimc_sen_device is
not set and used. So remove the field and
the code that check if it is non NULL
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Cc: <stable@vger.kernel.org> # for v5.4 and up
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This control represents a generic read/write area.
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When driver is built as module and probe during insmod is deferred
because of sensor subdevs, there is NULL pointer deference because
mdev is cleaned up and then access it from v4l2_device_unregister().
Fix the wrong mdev and v4l2 dev order in error path of probe.
This fixes below null pointer deference:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ca026f68
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[...]
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
PC is at ida_free+0x7c/0x160
LR is at xas_start+0x44/0x204
[...]
[<c0dafd60>] (ida_free) from [<c083c20c>] (__media_device_unregister_entity+0x18/0xc0)
[<c083c20c>] (__media_device_unregister_entity) from [<c083c2e0>] (media_device_unregister_entity+0x2c/0x38)
[<c083c2e0>] (media_device_unregister_entity) from [<c0843404>] (v4l2_device_release+0xd0/0x104)
[<c0843404>] (v4l2_device_release) from [<c0632558>] (device_release+0x28/0x98)
[<c0632558>] (device_release) from [<c0db1204>] (kobject_put+0xa4/0x208)
[<c0db1204>] (kct_put) from [<bf00bac4>] (fimc_capture_subdev_unregistered+0x58/0x6c [s5p_fimc])
[<bf00bac4>] (fimc_capture_subdev_unregistered [s5p_fimc]) from [<c084a1cc>] (v4l2_device_unregister_subdev+0x6c/0xa8)
[<c084a1cc>] (v4l2_device_unregister_subdev) from [<c084a350>] (v4l2_device_unregister+0x64/0x94)
[<c084a350>] (v4l2_device_unregister) from [<bf0101ac>] (fimc_md_probe+0x4ec/0xaf8 [s5p_fimc])
[...]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Fixes: 9832e155f1 ("[media] media-device: split media initialization and registration")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is the same incorrect approach to locking implemented in
vivid_stop_generating_vid_cap(), vivid_stop_generating_vid_out() and
sdr_cap_stop_streaming().
These functions are called during streaming stopping with vivid_dev.mutex
locked. And they all do the same mistake while stopping their kthreads,
which need to lock this mutex as well. See the example from
vivid_stop_generating_vid_cap():
/* shutdown control thread */
vivid_grab_controls(dev, false);
mutex_unlock(&dev->mutex);
kthread_stop(dev->kthread_vid_cap);
dev->kthread_vid_cap = NULL;
mutex_lock(&dev->mutex);
But when this mutex is unlocked, another vb2_fop_read() can lock it
instead of vivid_thread_vid_cap() and manipulate the buffer queue.
That causes a use-after-free access later.
To fix those issues let's:
1. avoid unlocking the mutex in vivid_stop_generating_vid_cap(),
vivid_stop_generating_vid_out() and sdr_cap_stop_streaming();
2. use mutex_trylock() with schedule_timeout_uninterruptible() in
the loops of the vivid kthread handlers.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Refactor some of the vivid_create_instance code by using a
new vivid_create_queue() helper function.
Also add some sanity checks for the node_types vs input/output_types
module options.
This patch resolves these two smatch parse errors:
drivers/media/platform/vivid/vivid-core.c:1679 vivid_create_instance() parse error: OOM: 3002600Kb sm_state_count = 6160113
drivers/media/platform/vivid/vivid-core.c: drivers/media/platform/vivid/vivid-core.c:1679
vivid_create_instance() parse error: __split_smt: function too hairy. Giving up after 33 seconds
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch fixes this error:
drivers/media/platform/ti-vpe/vpdma.c:767 dump_dtd() error: '%pad' expects argument of type 'dma_addr_t*', argument 2 has type 'uint*'
dtd->start_addr is a u32, so no need for %pad.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fixes this warning:
drivers/media/platform/am437x/am437x-vpfe.c:288 vpfe_ccdc_validate_param() warn: unsigned 'ccdcparam->alaw.gamma_wd' is never less than zero.
by dropping the gamma_wd < VPFE_CCDC_GAMMA_BITS_15_6 check
since VPFE_CCDC_GAMMA_BITS_15_6 is 0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Instead of validating the links to capture devices and subdevices with
the same function, use the default v4l function for links between
subdevices and only use a different function for validating between
capture device and subdevice.
This change should also ease future work to associate multiple mbus
codes for the same pixelformat in vimc_pix_map.
These changes were tested with
v4l2-compliance SHA: 3f806630e2ecbcebe31872b865c5c4b42f111a99, 64 bits
and passed all tests:
Grand Total for vimc device /dev/media0: 451, Succeeded: 451, Failed: 0, Warnings: 0
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@protonmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The number of components are only set, and never used.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The official name is "R-Car M3-N", not "R-Car M3N".
Fixes: 4e8c120de9 ("media: fdp1: Support M3N and E3 platforms")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The kernel driver never touches the decoded buffers with the CPU.
All accesses are either done by hardware DMA masters or userspace
mapping the buffers. This means we don't need a kernel virtual
address mapping for those buffers at all. As those buffers are
usually quite large, we can save a good deal of kernel vmalloc
space by requesting to not have a kernel mapping set up for them.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The BIT decoder picture run temporarily locks the bitstream mutex while
the coda device mutex is locked, to refill the bitstream ring buffer.
Consequently, the decoder start command, which locks both mutexes when
flushing the bitstream ring buffer, must lock the coda device mutex
first as well, to avoid an ABBA deadlock.
Fixes: e7fd95849b ("media: coda: flush bitstream ring buffer on decoder restart")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
>From isp_video_release(), &isp->video_lock is held and subsequent
vb2_fop_release() tries to lock vdev->lock which is same with the
previous one. Replace vb2_fop_release() with _vb2_fop_release() to
fix the recursive locking.
Fixes: 1380f5754c ("[media] videobuf2: Add missing lock held on vb2_fop_release")
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
"f->fmt.sdr.reserved" is uninitialized. As other peer drivers
like msi2500 and airspy do, the fix initializes it to avoid
memory disclosures.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2N(R8A774B1) SoC.
The CSI-2 module of RZ/G2N is similar to R-Car M3-N.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the SoC specific information for RZ/G2N(R8A774B1) SoC.
The VIN module of RZ/G2N is similar to R-Car M3-N.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Most Gen3 boards can output frames in NV12 format, add support for this
with a runtime check that the running hardware supports it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Most but not all Gen3 hardware support outputting NV12, add a flag to
indicate which SoCs do support it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If a pixel format is not supported by the hardware NULL is returned by
rvin_format_from_pixel() for that fourcc. Verify that the pixel format
is supported using this or skip it when enumerating.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If a process is interrupted while accessing the video device and the
device lock is contended, release() could return early and fail to free
related resources.
Note that the return value of the v4l2 release file operation is
ignored.
Fixes: 28ffeebbb7 ("[media] bdisp: 2D blitter driver using v4l2 mem2mem framework")
Cc: stable <stable@vger.kernel.org> # 4.2
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch corrects the SPDX License Identifier style
in header files related to Video drivers for Xilinx devices.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Allwinner H3 SoC contains deinterlace unit, which has several modes of
operation - bypass, weave, bob and mixed (advanced) mode. I don't know
how mixed mode works, but according to Allwinner it gives best results,
so they use it exclusively. Currently this mode is also hardcoded here.
For each interleaved frame queued, this driver produces 2 deinterlaced
frames. Deinterlaced frames are based on 2 consequtive output buffers,
except for the first 2, where same output buffer is given to peripheral
as current and previous.
There is no documentation for this core, so register layout and fixed
values were taken from BSP driver.
I'm not sure if maximum size of the image unit is capable to process is
governed by size of "flag" buffers, frequency or it really is some HW
limitation. Currently driver can process full HD image in ~15ms (7.5ms
for each capture buffer), which allows to process 1920x1080@60i video
smoothly in real time.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[hverkuil-cisco@xs4all.nl: add static to deinterlace_ioctl_ops]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add mean window size parameter for debayer filter as a control in
vimc-debayer.
vimc-debayer was patched to allow changing mean window parameter
of the filter without needing to reload the driver. The parameter
can now be set using a v4l2-ctl control(mean_window_size).
Co-developed-by: Laís Pessine do Carmo <laispc19@gmail.com>
Signed-off-by: Laís Pessine do Carmo <laispc19@gmail.com>
Signed-off-by: Arthur Moraes do Lago <arthurmoraeslago@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the 'struct device *dev' field exists in each of the
entity structs, it can be moved to the common struct vimc_ent_devevice.
It is then used to replace 'pr_err' with 'dev_err' in the streamer
code.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since the pads array is of known small size, there is no reason to
allocate it separately. Instead, it is embedded in the entity struct.
This also conforms to the media controller doc:
'Most drivers will embed the pads array in a driver-specific structure,
avoiding dynamic allocation.'
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
[hverkuil-cisco@xs4all.nl: remove unused vimc_pads_init()]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
the struct vimc_platform_data is not used anymore and can be removed.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function 'vimc_pipeline_s_stream' is not used and can be
removed.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc is a single kernel module and does not need to
export any symbols therefore there is no need for these
declarations.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since this function only calls v4l2_device_unregister_subdev,
it is pointless.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
according to the docs, this function must be called during
the cleanup phase after unregistering the entity.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc_sen_add function first registers the subdevice and then
calls tpg_alloc. If tpg_alloc fails it unregisters the subdevice
and then frees vsen, this cause double free since the release
callback that follows subdevice unregistration also frees vsen.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the add callback returns NULL on failure and the array
is initialized to NULLs, there is no need for the intermediate
assignment to local var.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since NULL value for vimc entity pointer indicates
that entity creation failed and this is tested, the
pointers should be initialized to NULL.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT.
Both PREEMPT and PREEMPT_RT require the same functionality which today
depends on CONFIG_PREEMPT.
Switch the Kconfig dependency to CONFIG_PREEMPTION.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There appears to be a copy-paste error on the access of
csc_coeffs.y2r.r601.full.coeff, I believe csc_coeffs.2yr.r601.full.coeff
should be used instead. This is a moot point as the code is never
reached, but at least use the correct structure element.
Addresses-Coverity: ("Copy-paste error")
Fixes: 3ff3a712a9 ("media: ti-vpe: vpe: don't rely on colorspace member for conversion")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sometimes it detects a weird resolution such as 1024x287 when the
actual resolution is 1024x768. To resolve such an issue, this
commit adds clearing for hsync and vsync polarity register bits
at the beginning of the first mode detection. This is recommended
in the datasheet.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To prevent inaccurate detections of resolution, this commit enables
clearing of hsync/vsync polarity bits based on probed sync state.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support metadata output in vivid driver.
Metadata output is used to set brightness, contrast, saturation
and hue.
Adds new files for metadata output.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds meatadata capture support in vivid driver.
Adds new files for metadata capture.
Adds vivid controls to generate PTS and SCR for metadata stream.
also fixes v4l2-compliance issues seen on metadata device.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Up to now VPE was relying on the colorspace value of struct v4l2_format
as an indication to perform color space conversion from YUV to RGB or
not.
Instead we should used the source/destination fourcc codes as a more
reliable indication to perform color space conversion or not.
To do so, we rework the csc module to use "struct v4l2_format *" as
parameters, and reorganize the coefficients tables in a more logical
way.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The RGB to YUV HD full range coefficients did not match the TRM values
and appeared to be a cut-n-paste from the YUV to RGB section.
Replace the entries with the values from the TRM.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All 4 of the "colorspace" components were not originally handled.
Causing issue related to xfer_func not being initialized properly.
This was found with v4l2-compliance test.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For each queue we need to maintain resolutions, pixel format,
bytesperline, sizeimage, colorspace, etc.
Instead of manually adding more entries in the vpe_q_data struct, it is
better to just add a "struct v4l2_format" member and use that to store
all needed information.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
[hverkuil@xs4all.nl: fix checkpatch warning]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VPE uses VPDMA (built-in dma engine) to transfer data to and from the IP
and memory. VPDMA expect 32 bits addresses. To make sure that is always
the case set the DMA mask and coherent mask for the device.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using dma_addr_t as the type to hold address inside of a fix sized
descriptor used by the vpdma firmware is prone to fail when the expected
width is 32 bits and suddenly when CONFIG_LPAE is enabled the data size
is now 64 bits shifted the remaining members of the descriptor in memory
which confuses the firmware.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(691): ret == 0
fail: v4l2-test-buffers.cpp(974): captureBufs(node, q, m2m_q,
frame_count, true)
test MMAP: FAIL
This caused the following Kernel Warning:
WARNING: CPU: 0 PID: 961 at
drivers/media/v4l2-core/videobuf2-core.c:1658
__vb2_queue_cancel+0x174/0x1d8
...
CPU: 0 PID: 961 Comm: v4l2-compliance Not tainted
4.14.62-01720-g20ecd717e87a #6
Hardware name: Generic DRA72X (Flattened Device Tree)
Backtrace:
[<c020b5bc>] (dump_backtrace) from [<c020b8a0>] (show_stack+0x18/0x1c)
r7:00000009 r6:60070013 r5:00000000 r4:c1053824
[<c020b888>] (show_stack) from [<c09232e8>] (dump_stack+0x90/0xa4)
[<c0923258>] (dump_stack) from [<c022b740>] (__warn+0xec/0x104)
r7:00000009 r6:c0c0ad50 r5:00000000 r4:00000000
[<c022b654>] (__warn) from [<c022b810>] (warn_slowpath_null+0x28/0x30)
r9:00000008 r8:00000000 r7:eced4808 r6:edbc9bac r5:eced4844
r4:eced4808
[<c022b7e8>] (warn_slowpath_null) from [<c0726f48>]
(__vb2_queue_cancel+0x174/0x1d8)
[<c0726dd4>] (__vb2_queue_cancel) from [<c0727648>]
(vb2_core_queue_release+0x20/0x40)
r10:ecc7bd70 r9:00000008 r8:00000000 r7:edb73010 r6:edbc9bac
r5:eced4844
r4:eced4808 r3:00000004
[<c0727628>] (vb2_core_queue_release) from [<c0729528>]
(vb2_queue_release+0x10/0x14)
r5:edbc9810 r4:eced4800
[<c0729518>] (vb2_queue_release) from [<c0724d08>]
(v4l2_m2m_ctx_release+0x1c/0x30)
[<c0724cec>] (v4l2_m2m_ctx_release) from [<bf0e8f28>]
(vpe_release+0x74/0xb0 [ti_vpe])
r5:edbc9810 r4:ed67a400
[<bf0e8eb4>] (vpe_release [ti_vpe]) from [<c070fccc>]
(v4l2_release+0x3c/0x80)
r7:edb73010 r6:ed176aa0 r5:edbc9868 r4:ed5119c0
[<c070fc90>] (v4l2_release) from [<c033cf1c>] (__fput+0x8c/0x1dc)
r5:ecc7bd70 r4:ed5119c0
[<c033ce90>] (__fput) from [<c033d0cc>] (____fput+0x10/0x14)
r10:00000000 r9:ed5119c0 r8:ece392d0 r7:c1059544 r6:ece38d80
r5:ece392b4
r4:00000000
[<c033d0bc>] (____fput) from [<c0246e00>] (task_work_run+0x98/0xb8)
[<c0246d68>] (task_work_run) from [<c022f1d8>] (do_exit+0x170/0xa80)
r9:ece351fc r8:00000000 r7:ecde3f58 r6:ffffe000 r5:ece351c0
r4:ece38d80
[<c022f068>] (do_exit) from [<c022fb6c>] (do_group_exit+0x48/0xc4)
r7:000000f8
[<c022fb24>] (do_group_exit) from [<c022fc00>]
(__wake_up_parent+0x0/0x28)
r7:000000f8 r6:b6c6a798 r5:00000001 r4:00000001
[<c022fbe8>] (SyS_exit_group) from [<c0207c80>]
(ret_fast_syscall+0x0/0x4c)
These warnings are caused by buffers which not properly cleaned
up/release during an abort use case.
In the abort cases the VPDMA desc buffers would still be mapped and the
in-flight VB2 buffers would not be released properly causing a kernel
warning from being generated by the videobuf2-core level.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(294): \
(int)g_sequence() < seq.last_seq + 1
fail: v4l2-test-buffers.cpp(740): \
buf.check(m2m_q, last_m2m_seq)
fail: v4l2-test-buffers.cpp(974): \
captureBufs(node, q, m2m_q, frame_count, true)
test MMAP: FAIL
The driver is failing to update the source frame sequence number in the
vb2 buffer object. Only the destination frame sequence was being
updated.
This is only a reporting issue if the user space app actually cares
about the frame sequence number. But it is fixed nonetheless.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(463): !pfmt.sizeimage
fail: v4l2-test-formats.cpp(736): \
Video Capture Multiplanar is valid, \
but TRY_FMT failed to return a format
test VIDIOC_TRY_FMT: FAIL
This failure is causd by the driver failing to handle out range
'bytesperline' values from user space applications.
VPDMA hardware is limited to 64k line stride (16 bytes aligned, so 65520
bytes). So make sure the provided or calculated 'bytesperline' is
smaller than the maximum value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(672): \
Video Capture Multiplanar: TRY_FMT(G_FMT) != G_FMT
fail: v4l2-test-formats.cpp(672): \
Video Output Multiplanar: TRY_FMT(G_FMT) != G_FMT
...
test VIDIOC_TRY_FMT: FAIL
The default pixel format was setup as pointing to a specific offset in
the vpe_formats table assuming it was pointing to the V4L2_PIX_FMT_YUYV
entry. This became false after the addition on the NV21 format (see
above commid-id)
So instead of hard-coding an offset which might change over time we need
to use a lookup helper instead so we know the default will always be what
we intended.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Fixes: 40cc823f7005 ("media: ti-vpe: Add support for NV21 format")
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance warns with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(718): \
This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(719): \
http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
...
test VIDIOC_TRY_FMT: FAIL
We need to make sure that the returns a valid pixel format in all
instance. Based on the v4l2 framework convention drivers must return a
valid pixel format when the requested pixel format is either invalid or
not supported.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
test VIDIOC_TRY_FMT: FAIL
This causes the following kernel panic:
Unable to handle kernel paging request at virtual address 56595561
pgd = ecd80e00
*pgd=00000000
Internal error: Oops: 205 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 930 Comm: v4l2-compliance Not tainted \
4.14.62-01715-gc8cd67f49a19 #1
Hardware name: Generic DRA72X (Flattened Device Tree)
task: ece44d80 task.stack: ecc6e000
PC is at __vpe_try_fmt+0x18c/0x2a8 [ti_vpe]
LR is at 0x8
Because the driver fails to properly check the 'num_planes' values for
proper ranges it ends up accessing out of bound data causing the kernel
panic.
Since this driver only handle single or dual plane pixel format, make
sure the provided value does not exceed 2 planes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VPE's max height supported MAX_H is set to 1184 which is the
padded height from VC1 decoder output.
In case of 90, 270 degree rotated video processing, input to
VPE will be 1080x1920, 720x1280 etc and MAX_H needs to be set
correct value. Setting MAX_H to 2048 as worst case height.
Signed-off-by: Ram Prasad <x0038811@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In NV21 format, the chroma plane is written to memory such that the U
and V components are swapped for NV12.
Create a new entry in the VPDMA formats to describe the correct data
types used in the data descriptors.
Update all checks for NV12 and add NV21 there as well.
Add support for V4L2_PIX_FMT_NV21 format for both capture and output
streams.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
SEQ_BT indicates the buffer for bottom field needs to be processed
before the top field.
Simplify the field selection logic to support SEQ_BT as well.
Modify the interlace flags to include any of alternate, SEQ_TB, SEQ_BT.
Update other format error checking to consider SEQ_BT.
Replace SEQ_TB with SEQ_XX wherever applicable.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of saving a pointer to the 'fh' member of struct vpe_ctx to
later have to use container_of to retrieve the actual pointer to the
context structure, which seems to confuse static code analysis tool
anyways, just save the pointer to the actual structure and then retrieve
it directly.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
commit 3dc2046ca7 ("[media] media: ti-vpe: vpe: allow use of user
specified stride") and commit da4414eaed ("[media] media: ti-vpe: vpdma:
add support for user specified stride") resulted in the Motion Vector
stride to be the same as the image stride.
This caused memory corruption in the output image as mentioned in
commit 00db969964 ("[media] media: ti-vpe: vpe: Fix line stride
for output motion vector").
Fixes: 3dc2046ca7 ("[media] media: ti-vpe: vpe: allow use of user specified stride")
Fixes: da4414eaed ("[media] media: ti-vpe: vpdma: add support for user specified stride")
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When TI CAL was introduce as another driver under platform/ti-vpe
adding a second entry into the ti-vpe directory in the platform
Makefile caused issues during parallel build.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Simplify these function implementations by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The image size is doubled for NV16 and is calculated as bytesperline *
height * 2 to accommodate the split of UV data. When writing the offset
to hardware, the width is used instead of bytesperline, fix this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The rectangle used to correct the compose settings when changing the
format was created inside a helper function and not where it was used.
This is confusing and makes the code harder to read, fix this.
This cleanup is made possible due to refactoring elsewhere and there is
no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After recent refactoring the rectangle named crop no longer reflects it
usage, to contain the source rectangle. Fix this by renaming it. There
is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f13d5f3619 ("media: vimc: Collapse component structure into a single monolithic driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The 2nd parameter of 'find_first_zero_bit()' is a number of bits, not of
bytes. So use 'csi2rx->max_lanes' instead of 'sizeof(lanes_used)'.
Fixes: 1fc3b37f34 ("media: v4l: cadence: Add Cadence MIPI-CSI2 RX driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As reported by jenkins@linuxtv.org, the build with i386 fails
with:
ld: drivers/media/platform/qcom/venus/helpers.o: in function `venus_helper_load_scale_clocks':
(.text+0x1d77): undefined reference to `__udivdi3'
ld: (.text+0x1dce): undefined reference to `__udivdi3'
make: *** [Makefile:1094: vmlinux] Error 1
That's because it divides an u32 bit integer by a u64 one.
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is possible for one HDMI connector to have multiple CEC adapters. The
typical real-world scenario is that where one adapter is used when the
device is in standby, and one that's better/smarter when the device is
powered up.
The cec-notifier changes were made with that in mind, but I missed that in
order to support this you need to tell cec_notifier_cec_adap_unregister()
which adapter you are unregistering from the notifier.
Add this additional argument. It is currently unused, but once all drivers
use this, the CEC core will be adapted for these use-cases.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e9fc8740-6be6-43a7-beee-ce2d7b54936e@xs4all.nl
When probed after the HDMI notifier, calling cec_notifier_cec_adap_register()
calls the enable() adapter callback, but the HW is not yet set up.
Moving cec_notifier_cec_adap_register() right before cec_register_adapter()
fixes the following crash:
Ignoring spurious kernel translation fault at virtual address 0000000000000008
[...]
Hardware name: Khadas VIM (DT)
[...]
pc : __do_kernel_fault+0xdc/0x120
lr : __do_kernel_fault+0xdc/0x120
[...]
Call trace:
__do_kernel_fault+0xdc/0x120
do_page_fault+0x180/0x458
do_translation_fault+0x64/0x70
do_mem_abort+0x3c/0x98
el1_da+0x20/0x94
meson_ao_cec_adap_enable+0x30/0x218 [ao_cec]
__cec_s_phys_addr+0x184/0x270
cec_s_phys_addr+0x44/0x60
cec_notifier_cec_adap_register+0x68/0x90
meson_ao_cec_probe+0xb0/0x288 [ao_cec]
[...]
el0_svc_compat+0x8/0x10
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 20958f9d5c ("media: meson/ao-cec: use cec_notifier_cec_adap_(un)register")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Current clock scaling calculations are same for vpu4 and
previous versions. For vpu4, Clock scaling calculations
are updated with cycles/mb and bitrate. This helps in
getting precise clock required.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add vpp cycles for different types of codec.
It indicates the cycles required by video hardware
to process each macroblock. Add vsp cycles, cycles
required by stream processor. Initialize the codec
data with core resources.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Failure to suspend (venus_suspend_3xx) happens when the system
is fresh booted and loading venus driver. This happens once and
after reload the venus driver modules the problem disrepair.
Fix the failure by skipping the check for WFI and IDLE bits if
PC_READY is on in control status register.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This aims to add a requests for bandwidth scaling depending
on the resolution and framerate (macroblocks per second). The
exact value of the requested bandwidth is get from a
pre-calculated tables for encoder and decoder.
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In downstream driver, there are two frequency tables defined,
one for the encoder and one for the decoder:
/* Encoders /
<972000 490000000 0x55555555>, / 4k UHD @ 30 /
<489600 320000000 0x55555555>, / 1080p @ 60 /
<244800 150000000 0x55555555>, / 1080p @ 30 /
<108000 75000000 0x55555555>, / 720p @ 30 */
/* Decoders /
<1944000 490000000 0xffffffff>, / 4k UHD @ 60 /
< 972000 320000000 0xffffffff>, / 4k UHD @ 30 /
< 489600 150000000 0xffffffff>, / 1080p @ 60 /
< 244800 75000000 0xffffffff>; / 1080p @ 30 */
It shows that encoder always needs a higher clock than decoder.
In current venus driver, the unified frequency table is aligned
with the downstream decoder table which causes performance issues
in encoding scenarios. Fix that by aligning frequency table on
worst case (encoding).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for cec-notifier to the cec-gpio driver.
This makes it possible to associate the CEC gpio pin with an HDMI
connector. This feature was always documented in the cec-gpio bindings:
Documentation/devicetree/bindings/media/cec-gpio.txt
But support for the hdmi-phandle property was never actually implemented in
this driver.
This patch adds support for this property.
It also fixes a few incorrect error returns in the probe() function, which
skipped the call to cec_delete_adapter().
Tested on a Raspberry Pi 3B with a modified vc4 driver.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The hardware is capable to passing V4L2_FIELD_ALTERNATE to user-space.
Allow users to request this field format but still default to using the
hardware interlacer if alternating is not explicitly requested.
Before this change a sensor providing data using alternate would be
always combined to an interlaced frame. After this change the user can
request to receive frames as alternate if the sensor provides it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The crop and compose rectangles are reset when s_fmt is called
resulting in potentially valid rectangles being lost when updating the
format. Fix this by mapping the rectangles inside the new format.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable to hold the video source information dimensions was poorly
named 'source'. This is confusing as a lot of other members of structs
share the same name with different purposes, rename it src_rect in
preparation of refactoring code.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2_FIELD_IS_INTERLACED() can be used to make the code more
readable, use it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While refactoring code the return statement became corrupted, fix it by
returning the correct return code.
Reported-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Fixes: 897e371389 ("media: rcar-vin: simplify how formats are set and reset"
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, if start streaming -> stop streaming -> start streaming
sequence is executed, driver will end job prematurely, if ctx->translen
is higher than 1, because "aborting" flag is still set from previous
stop streaming command.
Fix that by clearing "aborting" flag in start streaming handler.
Fixes: 96d8eab5d0 ("V4L/DVB: [v5,2/2] v4l: Add a mem-to-mem videobuf framework test device")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When vbi stream is started, followed by video streaming,
the vid_cap_streaming and vid_out_streaming were not being set to true,
which would cause the video stream to stop when vbi stream is stopped.
This patch allows to set vid_cap_streaming and vid_out_streaming to true.
According to Hans Verkuil it appears that these 'if (dev->kthread_vid_cap)'
checks are a left-over from the original vivid development and should never
have been there.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check for a potentially NULL pointer that was overlooked and use shorter
accessors to the same data. While we are at it, sprinkle a few comments.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Each of the supported decoder formats used to set the same RPC
interrupt handler by themselves, even though this could be done
by the IF init function itself. Move it to the right place and stop
making its symbol public.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
mtk_q_data::fmt is actually a pointer and must be dereferenced as such.
This went under the radar because mtk_v4l2_debug() evaluates to nothing
unless DEBUG is defined.
[acourbot: split into its own commit]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the array 'registers' on the stack but instead make it
static const. Makes the object code smaller by 45 bytes.
Before:
text data bss dec hex filename
17364 5000 0 22364 575c platform/s3c-camif/camif-regs.o
After:
text data bss dec hex filename
17255 5064 0 22319 572f platform/s3c-camif/camif-regs.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
At the beginning of the probe function, we have a call to
'request_muxed_region(BRA_SMB_BASE_ADDR, 7, "CEC00001")()'
A corresponding 'release_region()' is performed in the remove function but
is lacking in the error handling path.
Add it.
Fixes: b03c2fb97a ("media: add SECO cec driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The bus related static data included in the vpfe_fmt
static table can be derived dynamically instead.
This simplify the table and it's use.
We instead replace the per bus data info with just
the usual bit per pixel value for each supported
pixel format.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The try_fmt was not actually trying out the provided format
but merely returning the current format basically like get_fmt.
In addition set_fmt should first invoked try_fmt to validate the
given format before applying it to the hardware.
To fix all of these the whole get/try/set ioctl functions had to
be reworked.
When calculating the bytesperline/stride and sizeimage format
member we don't need to locally store the current value of
bytesperpixel as it can easily get derived dynamically.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
checkpatch.pl nows reports several:
WARNING: Prefer using '"%s...", __func__' to using '<function name>',
this function's name, in a string.
So fix these for the whole driver.
At the same time remove the function entry trace log as those can be
enabled using ftrace instead.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using a statically defined format array would cause issue when
multiple vpfe instance would be connected to sub-device of
different capabilities. We need to use an instance based array
instead to properly maintain a per port/instance format list.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VIDIOC_S_STD should not return an error if the value is identical
to the current one.
This error was highlighted by the v4l2-compliance test.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Returning queued vb2 buffers back to user space is a common
task best handled by a helper function.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When start_streaming fails the h/w module might be left enabled
inadvertently. Make sure it is disabled in the error path.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We were originally attempting to stop all processing as soon
as possible, but the in-progress DMA operation cannot be canceled.
This led to the module being in a busy state and prevented proper
power management functionality.
The existing implementation would attempt to clean things up by waiting
up to 50ms. However when receiving video frame at 15fps or lower,
it meant an inter frame arrival rate of 66.6 ms or higher.
In such cases upon tear down the following message could be seen:
omap_hwmod: vpfe0: _wait_target_disable failed
This patch fixes this issue by adding a stopping state where
we would wait for the next Vsync before disabling the hardware.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Previous generation of this driver were hard coded to handle
encoder/decoder where the first line never contains any data and
was therefore always skipped, however when dealing with actual
camera sensors the first line is always present.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently if vpfe is not active then it returns immediately in the
suspend and resume handlers. Change this so that it always performs the
pinctrl config so that we can still get proper sleep state configuration
on the pins even if we do not need to worry about fully saving and
restoring context.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move duplicated IS_SRC and IS_SINK dfines to common header. Rename
them to VIMC_IS_SRC and VIM_IS_SINK.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc uses Component API to split the driver into functional components.
The real hardware resembles a monolith structure than component and
component structure added a level of complexity making it hard to
maintain without adding any real benefit.
The sensor is one vimc component that would makes sense to be a separate
module to closely align with the real hardware. It would be easier to
collapse vimc into single monolithic driver first and then split the
sensor off as a separate module.
Collapse it into a single monolithic driver removing the Component API.
This patch removes the component API and makes minimal changes to the
code base preserving the functional division of the code structure.
Preserving the functional structure allows us to split the sensor off
as a separate module in the future.
Major design elements in this change are:
- Use existing struct vimc_ent_config and struct vimc_pipeline_config
to drive the initialization of the functional components.
- Make vimc_device and vimc_ent_config global by moving them to
vimc-common.h
- Add two new hooks add and rm to initialize and register, unregister
and free subdevs.
- All component API is now gone and bind and unbind hooks are modified
to do "add" and "rm" with minimal changes to just add and rm subdevs.
- vimc-core's bind and unbind are now register and unregister.
- Add a new field to vimc_device structure for saving the pointers to
struct vimc_ent_device(s) subdevs create in their "add" hooks. These
get used to create links and removing the subdevs. vimc-core allocates
this array which sized to number of entries in the topology defined in
the vimc_pipeline_config structure.
- vimc-core invokes "add" hooks from its vimc_register_devices().
The "add" hooks remain the same and register subdevs. They don't
create platform devices of their own and use vimc's pdev.dev as
their reference device. Each "add" hook returns pointer to its struct
vimc_ent_device. This is saved in the vimc_device ent_devs array.
- vimc-core invokes "rm" hooks from its unregister to unregister subdevs
and cleanup.
- vimc-core invokes "add" and "rm" hooks with pointer to struct vimc_device
and the corresponding vimc_ent_device saved in the ent_devs.
The following configure and stream test works on all devices.
media-ctl -d platform:vimc -V '"Sensor A":0[fmt:SBGGR8_1X8/640x480]'
media-ctl -d platform:vimc -V '"Debayer A":0[fmt:SBGGR8_1X8/640x480]'
media-ctl -d platform:vimc -V '"Sensor B":0[fmt:SBGGR8_1X8/640x480]'
media-ctl -d platform:vimc -V '"Debayer B":0[fmt:SBGGR8_1X8/640x480]'
v4l2-ctl -z platform:vimc -d "RGB/YUV Capture" -v width=1920,height=1440
v4l2-ctl -z platform:vimc -d "Raw Capture 0" -v pixelformat=BA81
v4l2-ctl -z platform:vimc -d "Raw Capture 1" -v pixelformat=BA81
v4l2-ctl --stream-mmap --stream-count=100 -d /dev/video1
v4l2-ctl --stream-mmap --stream-count=100 -d /dev/video2
v4l2-ctl --stream-mmap --stream-count=100 -d /dev/video3
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----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=QTT+
-----END PGP SIGNATURE-----
Merge tag 'media/v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a new sensor driver for ov5675
- a new platform driver for Allwinner A10 sensor interface
- some new remote controller keymaps
- some cosmetic changes at V4L2 core in order to avoid #ifdefs and to
merge two core modules into one
- removal of bcm2048 radio driver from staging
- removal of davinci_vpfe video driver from staging
- regression fix since Kernel 5.1 at the legacy VideoBuffer version 1
core
- added some documentation for remote controller protocols
- pixel format documentation was split on two files
- lots of other driver improvements and cleanups
* tag 'media/v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (321 commits)
media: videobuf-core.c: poll_wait needs a non-NULL buf pointer
media: sun4i: Make sun4i_csi_formats static
media: imx: remove unused including <linux/version.h>
media: stm32-dcmi: Delete an unnecessary of_node_put() call in dcmi_probe()
media: pvrusb2: qctrl.flag will be uninitlaized if cx2341x_ctrl_query() returns error code
media: em28xx: Fix exception handling in em28xx_alloc_urbs()
media: don't do a 31 bit shift on a signed int
media: use the BIT() macro
media: ov9650: add a sanity check
media: aspeed-video: address a protential usage of an unitialized var
media: vicodec: make life easier for static analyzers
media: remove include stdarg.h from some drivers
v4l2-core: fix coding style for the two new c files
media: v4l2-core: Remove BUG() from i2c and spi helpers
media: v4l2-core: introduce a helper to unregister a i2c subdev
media: v4l2-core: introduce a helper to unregister a spi subdev
media: v4l2-core: move i2c helpers out of v4l2-common.c
media: v4l2-core: move spi helpers out of v4l2-common.c
media: v4l2-core: Module re-organization
media: usbvision: Remove dead code
...
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, the ChromeOS EC core driver has nothing related to an MFD device, so
move that driver from the MFD subsystem to the platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The sun4i_csi_formats array is only used in sun4i_v4l2.c, so it doesn't
make any sense to have it !static.
[Sakari Ailus: const static -> static const]
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A null pointer would be passed to a call of the function “of_node_put”
immediately after a call of the function “of_graph_get_next_endpoint”
failed at one place.
Remove this superfluous function call.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On 32-bits archs, a signed integer has 31 bits plus on extra
bit for signal. Due to that, touching the 32th bit with something
like:
int bar = 1 << 31;
has an undefined behavior in C on 32 bit architectures, as it
touches the signal bit. This is warned by cppcheck.
Instead, force the numbers to be unsigned, in order to solve this
issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As warned by cppcheck:
[drivers/media/dvb-frontends/cx24123.c:434]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
[drivers/media/pci/bt8xx/bttv-input.c:87]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
[drivers/media/pci/bt8xx/bttv-input.c:98]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
...
[drivers/media/v4l2-core/v4l2-ioctl.c:1391]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
There are lots of places where we're doing 1 << 31. That's bad,
as, depending on the architecture, this has an undefined behavior.
The BIT() macro is already prepared to handle this, so, let's
just switch all "1 << number" macros by BIT(number) at the header files
with has 1 << 31.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> # exynos4-is and s3c-camif
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # omap3isp, vsp1, xilinx, wl128x and ipu3
Reviewed-by: Benoit Parrot <bparrot@ti.com> # am437x and ti-vpe
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While this might not occur in practice, if the device is doing
the right thing, it would be teoretically be possible to have
both hsync_counter and vsync_counter negatives.
If this ever happen, ctrl will be undefined, but the driver
will still call:
aspeed_video_update(video, VE_CTRL, 0, ctrl);
Change the code to prevent this to happen.
This was warned by cppcheck:
[drivers/media/platform/aspeed-video.c:653]: (error) Uninitialized variable: ctrl
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cppcheck incorrectly produces an error here:
[drivers/media/platform/vicodec/vicodec-core.c:1677]: (error) Pointer addition with NULL pointer.
While this is actually a false positive, it doesn't hurt to
reorder the checks to make the code simpler, handling first
the error patch, where no color or alpha components are there.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It returns '0' even when a failure happens on jpeg buffer allocation
so this commit fixes the issue.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If an error occurs in this function, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, introduce two labels to perform
the cleanup work.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In fdp1_open(), 'ctx' is allocated through kzalloc(). However, it is not
deallocated if v4l2_ctrl_new_std() fails, leading to a memory leak bug. To
fix this issue, free 'ctx' before going to the 'done' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The older CSI drivers have camera capture interface different from the one
in the newer ones.
This IP is pretty simple. Some variants (one controller out of two
instances on some SoCs) have an ISP embedded, but there's no code that make
use of it, so we ignored that part for now.
[Sakari Ailus: Wrapped a few long lines, set mbus code using a macro.]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Makefile and Kconfig for the sun6i CSI driver are included in the main
Makefile / KConfig file. Since we're going to add a new CSI driver for an
older chip, and the Cedrus driver eventually, it makes more sense to put
those in our directory.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of sensor malfunction, stop streaming timeout takes much longer
than expected. This is due to conversion of time to jiffies: milliseconds
multiplied with HZ (ticks/second) gives out a value of jiffies with 10^3
greater. We need to also divide by 10^3 to obtain the right jiffies value.
In other words FRAME_INTERVAL_MILLI_SEC must be in seconds in order to
multiply by HZ and get the right jiffies value to add to the current
jiffies for the timeout expire time.
Fixes: 195ebc43bf ("[media] V4L: at91: add Atmel Image Sensor Interface (ISI) support")
Signed-off-by: Alexandre Kroupski <alexandre.kroupski@ingenico.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the vicodec stateful decoder supports
dynamic resolution switching and bytestream parsing.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the mtk-vcodec decoder supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the venus vdec supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support of several sub-devices within pipeline instead
of a single one.
This allows to support a CSI-2 camera sensor connected
through a CSI-2 to parallel bridge.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add media controller support to dcmi in order
to walk within remote subdevices pipeline.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a trace of the set of supported fourcc/mbus_code which
intersect between DCMI and source sub-device.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename "subdev" entity struct field to "source"
to prepare for several subdev support.
Move asd field on top of entity struct.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The streaming state should be set to the first upstream sub-device only,
not everywhere, for a sub-device driver itself knows how to best control
the streaming state of its own upstream sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The omap3isp driver registered subdevs without the dev field being set. Do
that now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently when the call vsp1_dl_body_get fails and returns null the
error return path leaks the allocation of dl. Fix this by kfree'ing
dl before returning.
Addresses-Coverity: ("Resource leak")
Fixes: 5d7936b8e2 ("media: vsp1: Convert display lists to use new body pool")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a goto from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the goto in two
places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When support for the IPMMU is not enabled, the FDP driver may be
probe-deferred multiple times, causing several messages to be printed
like:
rcar_fdp1 fe940000.fdp1: FCP not found (-517)
rcar_fdp1 fe944000.fdp1: FCP not found (-517)
Fix this by reducing the message level to debug level, as is done in the
VSP1 driver.
Fixes: 4710b752e0 ("[media] v4l: Add Renesas R-Car FDP1 Driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
of_get_next_child() increments the reference count of the returning
device_node. Decrement it in the check if we are using the old or the
new DTB.
Fixes: ba1f1f70c2 ("[media] media: mtk-mdp: Fix mdp device tree")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Houlong Wei <houlong.wei@mediatek.com>
[hverkuil-cisco@xs4all.nl: use node instead of parent as temp variable]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit b6c61a6c37.
The requested pixelformat is being propagated from the capture to the
tpg in the sensor.
This was a bad design choice, as we start having the following issues:
* We set a pixelformat in the capture;
* We set matching media bus formats in the subdevices pads;
* Link validate looks fine (sizes matches, media bus formats matches);
* Issue: if some of the subdevice doesn't know how to generate the
requested pixelformat in the capture, then stream_on fails. This is bad
because capture says it supports that pixelformat, everything looks
fine, but it is not, and there is no way to find it out through the
links.
This patch was implemented so we could request any pixelformat from the
pipeline regardeless of the media bus format configured between pads.
Not all pixelformat can be mapped into a media bus code (e.g.
multiplanar formats), so with this patch we could request those
pixelformats from the tpg.
Solution: map pixelformats to media bus codes as before, and implement
conversions to other pixelformats in the capture to support multiplanar.
So first step to this solution is to revert this patch.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Lucas A. M. Magalhaes <lucmaga@gmail.com>
Tested-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit 3c1b9ac753.
Required to Revert "media: vimc: propagate pixel format in the stream"
which introduced the stream object in the vimc_ent_device struct.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Lucas A. M. Magalhaes <lucmaga@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The image stride was adjusted when it was written to hardware and not
when configuring the format. Calculate the correct stride value and
report it to userspace.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert omap_vout to the vb2 framework. After this change
'v4l2-compliance -s' passes all tests.
As usual, this vb2 conversion is a 'big bang' patch and hard to read.
Tested on a Pandaboard and a Beagle XM board.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch fixes the following v4l2-compliance failures:
- FIELD_ANY could be returned, which is not allowed.
- JPEG colorspace was set instead of SRGB.
- No control events.
- Empty bus_info in QUERYCAP.
- Overlay format handling wasn't zeroing bitmap/clips and
didn't return the chromakey correctly.
- G_FBUF didn't fill in many of the v4l2_framebuffer values.
Now also return the base address of the corresponding
framebuffer that this overlays.
- Missing ENUM/G/S_OUTPUT ioctls.
- ROTATE/VFLIP controls were added when the HW didn't support them.
With these changes 'v4l2-compliance' passes all non-streaming tests.
Tested on a Pandaboard and a Beagle XM board.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OMAP 4 TRM specifies that when using double-index addressing
the address increases by the ES plus the EI value minus 1 within
a frame. When a full frame is transferred, the address increases
by the ES plus the frame index (FI) value minus 1.
The omap-dma code didn't account for the 'minus 1' in the FI register.
To get correct addressing, add 1 to the src_icg value.
This was found when testing a hacked version of the media m2m-deinterlace.c
driver on a Pandaboard.
The only other source that uses this feature is omap_vout_vrfb.c,
and that adds a + 1 when setting the dst_icg. This is a workaround
for the broken omap-dma.c behavior. So remove the workaround at the
same time that we fix omap-dma.c.
I tested the omap_vout driver with a Beagle XM board to check that
the '+ 1' in omap_vout_vrfb.c was indeed a workaround for the omap-dma
bug.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Link: https://lore.kernel.org/r/952e7f51-f208-9333-6f58-b7ed20d2ea0b@xs4all.nl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
arch/microblaze/ defines out_be32() and in_be32(), so don't do that
again in the driver source.
Fixes these build warnings:
../drivers/media/platform/fsl-viu.c:36: warning: "out_be32" redefined
../arch/microblaze/include/asm/io.h:50: note: this is the location of the previous definition
../drivers/media/platform/fsl-viu.c:37: warning: "in_be32" redefined
../arch/microblaze/include/asm/io.h:53: note: this is the location of the previous definition
Fixes: 29d7506863 ("media: fsl-viu: allow building it with COMPILE_TEST")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Error h264 bitstreams which picture info are out range of
decoder hardware specification, and no nal start code at the
beginning of the buffer, stop decoding and exit.
Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for V4L2_PIX_FMT_BGRA/X32 and V4L2_PIX_FMT_RGBA/X32 formats.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cache flags, timestamps and timecode structure of OUTPUT buffers
in per-instance structure array and fill correctly the same when
the CAPTURE buffers are done.
This will make v4l2-compliance decoder streaming test happy.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Correct handling of OUTPUT buffers field and make v4l2-compliance
happy.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This refactors code for start/stop streaming vb2 operations and
adds a state machine handling similar to the one in stateful codec
API documentation. One major change is that now the HFI session is
started on STREAMON(OUTPUT) and stopped on REQBUF(OUTPUT,count=0),
during that time STREAMOFF(CAP,OUT) just flush buffers but doesn't
stop the session. The other major change is that now the capture
and output queues are completely separated.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In most of the cases the client will know better what could be
the maximum size for compressed data buffers. Change the driver
to permit the user to set bigger size for the compressed buffer
but make reasonable sanitation.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Until now we returned num_output_bufs set during reqbuf but
that could be wrong when we implement stateful Codec API. So
get the minimum buffers for capture from HFI. This is supposed
to be called after stream header parsing, i.e. after dequeue
v4l2 event for change resolution.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds three more helper functions:
* for internal buffers reallocation, applicable when we are doing
dynamic resolution change
* for initial buffer processing of capture and output queue buffer
types
All of them will be needed for stateful Codec API support.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This makes hfi_session_init to return an error when it is
already called without a call to hfi_session_deinit.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Export few HFI functions to use them from decoder to implement
more granular control needed for stateful Codec API compliance.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make hfi_flush function to receive an argument for the type
of flush.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Here we export few helper function to use them from decoder to
implement more granular control needed for stateful Codec API
compliance.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Accept the buffer size requested by client and compare it
against driver calculated size and set the maximum to
bitstream plane.
Signed-off-by: Malathi Gottam <mgottam@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert the via-camera to the vb2 framework. With this change this
driver passes all 'v4l2-compliance -s' tests on my OLPC 1.5.
Also tested with the Sugar 'Record' application.
All tests were done under the OLPC official 5.0.8 kernel.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
New RGB444, RGB555 and RGB32 variants were recently added. Now also
support them in vivid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit "vivid: reorder CEC allocation and control set-up" missed that the CEC adapter
needs a valid vfd->name, and that was now filled in after the CEC adapter was
created, leading to an empty adapter name.
Fill in the name earlier.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 4ee895e71a ("media: vivid: reorder CEC allocation and control set-up")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that both Gen2 (video device centric) and Gen3 (media device
centric) modes of the driver have controls it is required to always
setup the controls when opening the devices. Remove the check which only
calls v4l2_ctrl_handler_setup() for Gen2 and call it unconditionally.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The R-Car VIN module supports V4L2_PIX_FMT_ARGB555 and
V4L2_PIX_FMT_ABGR32 pixel formats. Add the hardware register setup and
allow the alpha component to be changed while streaming using the
V4L2_CID_ALPHA_COMPONENT control.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch warning for macro VNDMR_A8BIT]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In preparation to adding support for RGB pixel formats with an alpha
component add a control to allow the user to control which alpha value
should be used.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The value have nothing to do with ARGB1555, it controls if the alpha
component should be filled in for ARGB1555 or ARGB888. Rename it to
reflect this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rework OF endpoint parsing for the omap3isp driver. This does add some
lines of code. The benefits are still clear:
- the great complication related to callbacks in endpoint parsing is gone;
instead endpoints are obtained port by port and
- endpoints may now have a default bus configuration which was not
possible while using callbacks. This driver does not benefit from that
feature, but as the omap3isp is one of the exemplary drivers, this works
as an example for driver developers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_async_notifier_add_fwnode_subdev() did not take a reference of
the added fwnode, relying on the caller to handle that instead, in essence
putting the fwnode to be added if there was an error.
As the reference is eventually released during the notifier cleanup, this
is not intuitive nor logical. Improve this by always getting a reference
when the function succeeds, and the caller releasing the reference when it
does not *itself* need it anymore.
Luckily, perhaps, there were just a handful of callers using the function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The davinci-vpif driver dereferences its local endpoints after releasing
the reference to them.
The driver also puts its endpoints explicitly while the
of_graph_get_next_endpoint() does that, too, leading to obtaining a
reference once and releasing it twice.
Both are fixed by this patch.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds support for CSI2TX v2.1 version of the controller.
Signed-off-by: Jan Kotas <jank@cadence.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch fixes mapping of lanes in DPHY_CFG register
of the controller. In the register, bit 0 means first data lane.
In Linux we currently assume lane 0 is clock.
Signed-off-by: Jan Kotas <jank@cadence.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds lane checks for CSI2TX, to prevent clock lane
being used as a data lane.
Signed-off-by: Jan Kotas <jank@cadence.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add an extra condition to add the video output control class when the
device has some hdmi outputs defined. This is required to then always
be able to add the display present control, which is enabled when
there are some hdmi outputs.
This fixes the corner case where no_error_inj is enabled and the
device has no frame buffer but some hdmi outputs, as otherwise the
video output control class would be added anyway. Without this fix,
the sanity checks fail in v4l2_ctrl_new() as name is NULL.
Fixes: c533435ffb ("media: vivid: add display present control")
Cc: stable@vger.kernel.org # for 5.3
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
struct vpfe_pixel_format was defined, but never used. Remove it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Simplify vpfe_pixel_format to just contain the pixelformat and bpp fields.
All others are unused.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver didn't use struct v4l2_fh, so add it.
This is a very basic conversion. I can't test this on real hardware,
so I didn't dare to also convert the driver to start using the
v4l2-mem2mem ioctl/fop helpers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This fixes autoloading the module by the OF compatible string.
Fixes: 83c40e6611 ("media: marvell-ccic/mmp: add devicetree support")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, the v4l2 control code is a bit silent on errors.
Add debug messages on (hopefully) most of the error paths.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of scattering black listing of pixel formats who are not
supported on particular platforms move it to a central location.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Format the current existing comments as kernel-doc comments, to be
reused at kernel documention. Add opening marks (/**) and return values.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As in "Function parameters" at doc-guide/kernel-doc.rst, "the
continuation of the description should start at the same column as the
previous line". Make the @producer_pixfmt comply with that.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As a more complete version of vimc_streamer_s_streamer comment was added
at "media: vimc: stream: add missing function documentation" commit in
.c file, remove the old documentation from .h file.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert this driver to use struct v4l2_fh and as a result switch to
using vb2/v4l2_mem2mem helper functions as well.
Only compile-tested due to lack of hardware. This driver is however
very similar to the m2m-deinterlace driver in this respect, and that
v4l2_fh conversion has been properly tested.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver is one of the few that is still not using struct
v4l2_fh. Convert it.
Tested on a Pandaboard.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert this driver to use struct v4l2_fh and as a result switch to
using vb2/v4l2_mem2mem helper functions as well.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The call to of_get_parent returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/ti-vpe/cal.c:1621:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1607, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/exynos4-is/fimc-is.c:813:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/fimc-is.c:870:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/fimc-is.c:885:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:545:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 541, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:528:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 499, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:534:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 499, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Building a KASAN-enabled kernel with clang ends up in a case where too
much is inlined into vivid_thread_vid_cap() and the stack usage grows
a lot, possibly when the register allocation fails to produce efficient
code and spills a lot of temporaries to the stack. This uses more
than twice the amount of stack than the sum of the individual functions
when they are not inlined:
drivers/media/platform/vivid/vivid-kthread-cap.c:766:12: error: stack frame size of 2208 bytes in function 'vivid_thread_vid_cap' [-Werror,-Wframe-larger-than=]
Marking two of the key functions in here as 'noinline_for_stack' avoids
the pathological case in clang without any apparent downside for gcc.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The patch fixes various v4l2-compliance failures:
- missing support for control events
- support of s/g_std even though this doesn't apply to a webcam
- missing colorspace reporting
- bus_info wasn't filled in by VIDIOC_QUERYCAP
- parm.capture.readbuffers was overridden with wrong value
- viacam_enum_framesizes/intervals didn't check the arguments
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Modern V4L2 drivers should use struct v4l2_fh to represent a filehandle.
This driver was one of the few that didn't use it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The power management hooks were never unregistered, which caused a
crash when unloading the module.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Probable cut&paste typo - use the correct field size.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the Amlogic SM1 SoC Family to the G12A AO-CECB
derivative.
It only adds a single init register.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[hverkuil-cisco@xs4all.nl: dropped spurious newline]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver builds fine without these, and they cause build
problems once davinci multiplatform support is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a potential integer overflow when int 2 is left shifted
as this is evaluated using 32 bit arithmetic but is being used in
a context that expects an expression of type s64. Fix this by
generating a mask using GENMASK to avoid a 32 bit overflow.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: 8a99e9faa1 ("media: vivid: add HDMI (dis)connect RX emulation")
Fixes: 79a792dafa ("media: vivid: add HDMI (dis)connect TX emulation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The priv field of struct v4l2_pix_format shouldn't be set by drivers,
it's set by the v4l2 core instead to V4L2_PIX_FMT_PRIV_MAGIC.
Drop this from the few media drivers that still do this.
Note that the gspca patch is slightly more involved since some of the
sub-gspca drivers use the priv field internally.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[hverkuil-cisco@xs4all.nl: fix clash in gspca between priv arg and priv variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cec_notifier_cec_adap_(un)register instead of
cec_notifier_get, cec_notifier_put and cec_register_cec_notifier.
Also enable the CEC_CAP_CONNECTOR_INFO capability.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cec_notifier_cec_adap_(un)register instead of
cec_notifier_get, cec_notifier_put and cec_register_cec_notifier.
Also enable the CEC_CAP_CONNECTOR_INFO capability.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cec_notifier_cec_adap_(un)register instead of
cec_notifier_get, cec_notifier_put and cec_register_cec_notifier.
Also enable the CEC_CAP_CONNECTOR_INFO capability.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cec_notifier_cec_adap_(un)register instead of
cec_notifier_get_conn, cec_notifier_put and cec_register_cec_notifier.
Also enable the CEC_CAP_CONNECTOR_INFO capability.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ettore Chimenti <ek5.chimenti@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cec_notifier_cec_adap_(un)register instead of
cec_notifier_get_conn, cec_notifier_put and cec_register_cec_notifier.
Also enable the CEC_CAP_CONNECTOR_INFO capability.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the new cec_notifier_cec_adap_(un)register() functions to
(un)register the notifier for the CEC adapter.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The device_caps in struct video_device are already set correctly,
so there is no need to set them in querycap again.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2 core sets the format description and flags for the driver in order
to ensure consistent naming.
So drop the strscpy of the description in drivers. Also remove any
description strings in driver-internal structures since those are
no longer needed.
And in am437x-vpfe.c drop an unnecessary f->type assignment in
vpfe_enum_fmt().
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[hverkuil-cisco@xs4all.nl: addressed some small suggestions from Laurent]
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ABgl
-----END PGP SIGNATURE-----
Merge tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Atmel microship ISC driver
- coda has gained support for mpeg2 and mpeg4
- cxusb gained support for analog TV
- rockchip staging driver was split into two separate staging drivers
- added a new staging driver for Allegro DVT video IP core
- added a new staging driver for Amlogic Meson video decoder
- lots of improvements and cleanups
* tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (398 commits)
media: allegro: use new v4l2_m2m_ioctl_try_encoder_cmd funcs
media: doc-rst: Fix typos
media: radio-raremono: change devm_k*alloc to k*alloc
media: stv0297: fix frequency range limit
media: rc: Prefer KEY_NUMERIC_* for number buttons on remotes
media: dvb_frontend: split dvb_frontend_handle_ioctl function
media: mceusb: disable "nonsensical irdata" messages
media: rc: remove redundant dev_err message
media: cec-notifier: add new notifier functions
media: cec: add struct cec_connector_info support
media: cec-notifier: rename variables, check kstrdup and n->conn_name
media: MAINTAINERS: Add maintainers for Media Controller
media: staging: media: tegra-vde: Defer dmabuf's unmapping
media: staging: media: tegra-vde: Add IOMMU support
media: hdpvr: fix locking and a missing msleep
media: v4l2: Test type instead of cfg->type in v4l2_ctrl_new_custom()
media: atmel: atmel-isc: fix i386 build error
media: v4l2-ctrl: Move compound control initialization
media: hantro: Use vb2_get_buffer
media: pci: cx88: Change the type of 'missed' to u64
...
Define struct cec_connector_info in media/cec.h and define
CEC_CAP_CONNECTOR_INFO. In a later patch this will be moved to
uapi/linux/cec.h.
The CEC_CAP_CONNECTOR_INFO capability can be set by drivers, but
cec_allocate_adapter() will remove it again until the public API
for this can be enabled once all drm drivers wire this up correctly.
Also add the cec_fill_conn_info_from_drm and cec_s_conn_info functions,
which are needed by drm drivers to fill in the cec_connector info
based on a drm_connector.
The cec_notifier_(un)register and cec_register_cec_notifier
prototypes were moved from cec-notifier.h to cec.h since cec.h no longer
includes cec-notifier.h. These headers included each other before,
which caused various problems.
Due to these changes the seco-cec driver was changed as well: it
should include cec-notifier.h, not cec.h.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_fill_pixfmt() returns -EINVAL if the pixelformat used as parameter is
invalid or if the user is trying to use a multiplanar format with the
singleplanar API. Currently, the vimc_cap_try_fmt_vid_cap() returns such
value, but vimc_cap_s_fmt_vid_cap() is ignoring it. Fix that and returns
an error value if vimc_cap_try_fmt_vid_cap() has failed.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Suggested-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for dynamically changing the GOP size, bitrate, frame rate,
constant intra quantization parameter, number of intra refresh macro
blocks and slice mode parameters.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changing slice mode dynamically while encoding will require to calculate
the register value again, so split it out into a separate function.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the platform device pointer is stored in struct coda_dev,
only to convert it into a device pointer wherever it is used. Just
store the device pointer directly.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If reordering is not enabled, the last decoded frame has to be the last
returned buffer. Otherwise wait for the firmware to report no more
frame to display. In that case the return buffer is the last one as
well, and can be reported as such.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there is still a buffer pending, mark it as the last buffer. It will
create a meta that is flagged as last when the buffer is copied into the
bitstream ring buffer. If there are no more buffers pending, find the
last bitstream meta and mark it as last. If there is no bitstream meta
either, wake up the capture queue as there will be no more decoded
frames.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure that an encoder stop command running concurrently with an
encoder finish_run always either flags the last returned buffer or wakes
up the capture queue to signal the end of stream condition afterwards.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the flagged last output buffer to also flag the corresponding
capture buffer after encoding. This causes the end of stream event
to be issued and the buffer to be dequeued with the last flag set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there are no pending queued output buffers to be encoded, waking up
the capture queue with -EPIPE signals end of stream. If there are
pending buffers on the other hand, setting the V4L2_BUF_FLAG_LAST on
the resulting encoded capture buffers is all that is needed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using the output queue sequence counter to determine the last buffer to
be encoded or decoded always was fragile at best. Now that we have the
last buffer flag propagating from the output queue to the capture queue
correctly, this is not needed anymore.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mark the last output buffer to be encoded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there are still queued output buffers pending to be copied into the
bitstream ring buffer, setting the stream end flag should be deferred
until the marked last output buffer is written into the bitstream ring
buffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mark the last output buffer to be decoded and only copy pending queued
output buffers into the bitstream ring buffer in the BIT processor
decoder case.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since V4L2_BUF_FLAG_LAST is a CAPTURE only flag, clear it from OUTPUT
buffers in QBUF and DQBUF. This allows to use the flag internally to
signal the last buffer to decode after a decoder stop command was
issued.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If no more frames are decoded in bitstream end mode, and a previously
decoded frame has been returned, the firmware still increments the frame
number. To avoid a sequence number mismatch after decoder restart,
increment the sequence_offset correction parameter.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The bitstream ringbuffer might be in an underrun state after draining,
or it might still contain unread data if the previous decoder stop
command was flagged as immediate. Flush the bitstream ring buffer
during V4L2_DEC_CMD_START to get into a well defined state. Also fill
the bitstream with buffers that have been queued during draining,
to resume decoding immediately.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On CODA960, sequence initialization can succeed if less than 512 bytes
are ready in the bitstream ring buffer.
On other variants, warn about too small payload in start_streaming.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the first buffer contains only headers, the sequence initialization
command fails. On CodaHx4 the buffer must be padded to at least 512
bytes, on CODA960 it seems to be enough to just repeat the sequence and
extension headers (MPEG-2) or the VOS and VO headers (MPEG-4) once for
for sequence initialization to succeed without further bitstream data.
On CodaHx4 the headers can be repeated multiple times until the 512 byte
mark is reached.
A similar issue was solved for h.264 by padding with a filler NAL in
commit 0eef89403e ("[media] coda: pad first h.264 buffer to 512
bytes").
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pass vaddr and size to coda_bitstream_queue instead of a struct
vb2_v4l2_buffer to make it reusable for queueing data that is
not exactly a whole v4l2 buffer into the bitstream ringbuffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Combine the separate auxiliary buffer, buffer meta, frame type, and
decode error arrays into an array of struct coda_internal_frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stateful decoder API requires decoders to signal detection
of stream dimensions via the V4L2_EVENT_SOURCE_CHANGE event.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a sequence initialization work item to be run when OUTPUT buffers
are queued in the initialization state.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sequence initialization already has to happen during the
initialization phase, after headers have been queued on the OUTPUT
queue. This means that sequence initialization has to be queued as
a work item from QBUF on the OUTPUT queue. The internal framebuffer
setup should be done later during VIDIOC_REQBUFS() on the CAPTURE
queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the DEC_CMD_STOP command is issued after the context has already
consumed all the queued buffers, we need to make sure to wake the
destination queue with last_buffer_dequeued set, to allow userspace to
make progress in its EOS handling.
As there might still be picture run workers pending at that point, we
need to synchronize with them, so the sequence number comparison reads
stable values.
reword commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Combine setting the last_buffer_dequeued flag on the capture video
queue and waking up its done workqueue into a helper function.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
coda_encoder_cmd() is racy, as the last scheduled picture run worker can
still be in-flight while the ENC_CMD_STOP command is issued. Depending
on the exact timing the sequence numbers might already be changed, but
the last buffer might not have been put on the destination queue yet.
In this case the current implementation would prematurely wake the
destination queue with last_buffer_dequeued=true, causing userspace to
call streamoff before the last buffer is handled.
Close this race window by synchronizing with the pic_run_worker before
doing the sequence check.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[l.stach@pengutronix.de: switch to flush_work, reword commit message]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sequence number handling assumed that the BIT processor frame number
starts counting at 1, but this is not true for the MPEG-2 decoder,
which starts at 0. Fix the sequence counter offset detection to handle
this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use mem2mem try_en/decoder_cmd helpers to ensure consistent behaviour
with other video codec drivers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CMD_START shall be used to start the processing after a drain that
was initiated with CMD_STOP.
Up until now, a drain on coda could only be finished with a
STREAMOFF-STREAMON, which resulted in a reset of the device.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As warned by sparse:
drivers/media/platform/marvell-ccic/cafe-driver.c:475:23: warning: symbol 'ov7670_info' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It's impossible for mmpcam_calc_dphy() to be called without it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Avoid pointlessly calling calc_dphy() when the bus is not
V4L2_MBUS_CSI2_DPHY. This will make it easier to replace the platform data
with devicetree.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sensor needs the MCLK clock running when it's being probed. On
platforms where the sensor is instantiated from a DT (MMP2) it is going
to happen asynchronously.
Therefore, the current modus operandi, where the bridge driver fiddles
with the sensor power and clock itself is not going to fly. As the comments
wisely note, this doesn't even belong there.
Luckily, the ov7670 driver is already able to control its power and
reset lines, we can just drop the MMP platform glue altogether.
It also requests the clock via the standard clock subsystem. Good -- let's
set up a clock instance so that the sensor can ask us to enable the clock.
Note that this is pretty dumb at the moment: the clock is hardwired to a
particular frequency and parent. It was always the case.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
An instance of a sensor on DT-based MMP2 platform is always going to be
created asynchronously.
Let's move the manual device creation away from the core to the Cafe
driver (used on OLPC XO-1, not present in DT) and set up appropriate
async matches: I2C on Cafe, FWNODE on MMP (OLPC XO-1.75).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The platform data is actually not used anywhere (along with the CSI
support) and should be safe to remove.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the names more suitable for devicetree bindings.
There are no board files utilizing this, thus we seem to be at liberty
at renaming this without consequences.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The access to REG_CLKCTRL or REG_CTRL1 without the clock enabled hangs
the machine. Enable the clock first.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove structure members and headers that are not actually used. Saves
us from some noise in subsequent cleanup commits.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This accesses the clock registers directly and thus is going to stay in the
way of making the driver devicetree friendly.
No boards seems to actually use this. If it's somehow actually needed it
needs to be done differently.
This reverts commit 7c269f454e.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set/invalidate physical addresses based on the configuration of the
display present control. This is relevant not only when the display
present control is modified, but also when the Vivid instance EDID is
set/cleared.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CEC adapters and controllers (handlers) are now set up as follows:
1. Allocate CEC adapters: setup of control handlers in next step
requires these adapters to be allocated.
2. Setup of control handlers: This must be done prior to registering
and exposing the adapters to user space to avoid a race condition.
3. Register CEC adapters: make them available to user space.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: PTR_ERR -> PTR_ERR_OR_ZERO]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds the following bitmask control:
-V4L2_CID_DV_RX_POWER_PRESENT
The RX_POWER_PRESENT bitmask is set based on the digital video timings
signal mode. This also removes 1/1 warnings for v4l2-compliance test on
vivid instance with HDMI input.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds the following bitmask controls:
-V4L2_CID_DV_TX_EDID_PRESENT
-V4L2_CID_DV_TX_HOTPLUG
-V4L2_CID_DV_TX_RXSENSE
The bitmasks are all set based on the custom vivid DISPLAY_PRESENT
control. This also removes 2/2 v4l2-compliance warnings for vivid
output device.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will be used for HDMI-specific controls such as hotplug detection
and power present.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a custom control for selecting the presence of a display connected
to the active output. This control is part of an effort to implement
proper HDMI (dis)connect behavior for vivid.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make the following properties per-input:
-Standard Signal Mode
-Standard
These properties need to be per-input in order to implement proper HDMI
(dis)connect-behavior, where the signal mode will be used to signify
whether or not there is an inpute device connected.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make the following properties per-input
-DV Timings Signal Mode
-DV Timings
These properties need to be per-input in order to implement proper
HDMI (dis)connect-behavior, where the signal mode will be used to
signify whether or not there is an input device connected.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
AST2500 silicon revision A1 and A2 have a silicon bug which causes
extremly long capturing time on specific resolutions (1680 width).
To fix the bug, this commit adjusts the capturing window register
setting to 1728 if detected width is 1680. The compression window
register setting will be kept as the original width so output
result will be the same.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add comments at vimc_streamer_s_stream and vimc_streamer_thread, making
the vimc-stream totally documented.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
[hverkuil-cisco@xs4all.nl: fix typo: in a fixed framerate -> at a fixed framerate]
[hverkuil-cisco@xs4all.nl: fix typo: stops the thread -> stop the thread]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The tpf_min (1/100) and tpf_max (100/1) are used as the lowest and the
highest allowable value for the desired frame period in
vivid_vid_cap_s_parm().
But the comparison between these values is unnecessary because the compared
value is already chosen from webcam_intervals[] (from 1/60 to 1/1).
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We were getting the codec interface through a proxy function that does
not bring anything compared to just accessing the interface definition
directly, so just do that. Also make the decoder interfaces const.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The interface used to communicate with the firmware casts pointers
into unsigned longs and back again in order to store private
references, all of this for pointers that remain purely in the kernel.
Replace these unsigned longs with void pointers to make the code a bit
sturdier and easier to follow.
Also simplify some interfaces by removing arguments that could be
infered from others.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch alignment warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove redundant Makefile rules (vimc_capture-objs, ...).
Stop exposing vimc-{common, streamer} as modules, since there's no use
case where they would be individually added/removed from Vimc. As
consequence, remove MODULE_ macros from vimc-{common, streamer}.
`-objs` is fitted for building host programs, change to `-y`, more
straightforward for device drivers.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Suggested-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix typo on "tranforming". Add a line break so it keeps under 80 columns.
Fix typo on "[it] need".
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the beginning the second clock ('special', 'sclk') was optional and
it is not available on some variants of Exynos SoCs (i.e. Exynos5420 with
v7 of MFC hardware).
However commit 1bce6fb3ed ("[media] s5p-mfc: Rework clock handling")
made handling of all specified clocks mandatory. This patch restores
original behavior of the driver and fixes its operation on
Exynos5420 SoCs.
Fixes: 1bce6fb3ed ("[media] s5p-mfc: Rework clock handling")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After the rework of the Gen2 file operations it's now trivial to merge
the Gen2 and Gen3 versions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function no longer serve a purpose as most tasks it performed have
been refactored, fold what remains of it into the only caller. While at
it add error checking for v4l2_ctrl_handler_setup().
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The two power helpers are now only dealing with the parallel subdevice,
merge them into a single rvin_power_parallel() helper to reduce code
duplication.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The helpers rvin_power_{on,off} deal with both VIN and the parallel
subdevice power. This makes it hard to merge the Gen2 and Gen3
open/release functions. Move the VIN power handling directly to the
open/release functions to prepare for the merge.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The format is already synced when the subdevice is bound, there is no
need to do do it every time the video device is opened.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The user should be allowed to break waiting for the lock when opening
the video device.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Runtime PM is already enabled unconditionally when the driver is probed
and disabled when it's removed. There is no point in doing it again for
Gen2 when opening and closing the video device.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver does not implement runtime resume and suspend function so
there is little point in trying to call them. This is a leftover from
the drivers soc_camera beginnings.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fixed issues that can lead to potential bugs.
Cleanup order in the driver
Taking into consideration std control creation can fail
mutex_destroy call
changing controller_formats with const specifier
some cosmetic cleanups
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This splits the Atmel ISC driver into a common base: atmel-isc-base.c
and the driver probe/dt part , atmel-sama5d2-isc.c
This is needed to keep a common ground for the sensor controller which will
be reused.
The atmel-isc will use the common symbols inside the atmel-isc-base
Future driver will also use the same symbols and redefine different aspects,
for a different version of the ISC.
This is done to avoid complete code duplication by creating a totally
different driver for the new variant of the ISC.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: folded 'atmel: atmel-sama5d2-isc: fixed checkpatch warnings' into this patch]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the newly introduced vb2_get_buffer API and avoid
accessing buffers in the queue directly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the newly introduced vb2_get_buffer API and avoid
accessing buffers in the queue directly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fixed checkpatch alignment warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the newly introduced vb2_get_buffer API and avoid
accessing buffers in the queue directly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Gj1MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGctkH/0At3+SQPY2JJSy8
i6+TDeytFx9OggeGLPHChRfehkAlvMb/kd34QHnuEvDqUuCAMU6HZQJFKoK9mvFI
sDJVayPGDSqpm+iv8qLpMBPShiCXYVnGZeVfOdv36jUswL0k6wHV1pz4avFkDeZa
1F4pmI6O2XRkNTYQawbUaFkAngWUCBG9ECLnHJnuIY6ohShBvjI4+E2JUaht+8gO
M2h2b9ieddWmjxV3LTKgsK1v+347RljxdZTWnJ62SCDSEVZvsgSA9W2wnebVhBkJ
drSmrFLxNiM+W45mkbUFmQixRSmjv++oRR096fxAnodBxMw0TDxE1RiMQWE6rVvG
N6MC6xA=
=+B0P
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc5' into patchwork
Linux 5.2-rc5
There are some media fixes on -rc5, so merge from it at media
devel tree.
* tag 'v5.2-rc5': (210 commits)
Linux 5.2-rc5
x86/microcode, cpuhotplug: Add a microcode loader CPU hotplug callback
Smack: Restore the smackfsdef mount option and add missing prefixes
ftrace: Fix NULL pointer dereference in free_ftrace_func_mapper()
module: Fix livepatch/ftrace module text permissions race
tracing/uprobe: Fix obsolete comment on trace_uprobe_create()
tracing/uprobe: Fix NULL pointer dereference in trace_uprobe_create()
tracing: Make two symbols static
tracing: avoid build warning with HAVE_NOP_MCOUNT
tracing: Fix out-of-range read in trace_stack_print()
gfs2: Fix rounding error in gfs2_iomap_page_prepare
x86/kasan: Fix boot with 5-level paging and KASAN
timekeeping: Repair ktime_get_coarse*() granularity
Revert "ALSA: hda/realtek - Improve the headset mic for Acer Aspire laptops"
mm/devm_memremap_pages: fix final page put race
PCI/P2PDMA: track pgmap references per resource, not globally
lib/genalloc: introduce chunk owners
PCI/P2PDMA: fix the gen_pool_add_virt() failure path
mm/devm_memremap_pages: introduce devm_memunmap_pages
drivers/base/devres: introduce devm_release_action()
...
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=UXan
-----END PGP SIGNATURE-----
Merge tag 'media/v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a debug warning for satellite tuning at dvb core was producing too
much noise
- a regression at hfi_parser on Venus driver
* tag 'media/v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: venus: hfi_parser: fix a regression in parser
media: dvb: warning about dvb frequency limits produces too much noise
MFC v6 and v7 has no register to read min scratch buffer size, so it has
to be read conditionally only if hardware supports it. This fixes following
NULL pointer exception on SoCs with MFC v6/v7:
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = f25837f9
[00000000] *pgd=bd93d835
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
Modules linked in: btmrvl_sdio btmrvl bluetooth mwifiex_sdio mwifiex ecdh_generic ecc
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
PC is at s5p_mfc_get_min_scratch_buf_size+0x30/0x3c
LR is at s5p_mfc_get_min_scratch_buf_size+0x28/0x3c
...
[<c074f998>] (s5p_mfc_get_min_scratch_buf_size) from [<c0745bc0>] (s5p_mfc_irq+0x814/0xa5c)
[<c0745bc0>] (s5p_mfc_irq) from [<c019a218>] (__handle_irq_event_percpu+0x64/0x3f8)
[<c019a218>] (__handle_irq_event_percpu) from [<c019a5d8>] (handle_irq_event_percpu+0x2c/0x7c)
[<c019a5d8>] (handle_irq_event_percpu) from [<c019a660>] (handle_irq_event+0x38/0x5c)
[<c019a660>] (handle_irq_event) from [<c019ebc4>] (handle_fasteoi_irq+0xc4/0x180)
[<c019ebc4>] (handle_fasteoi_irq) from [<c0199270>] (generic_handle_irq+0x24/0x34)
[<c0199270>] (generic_handle_irq) from [<c0199888>] (__handle_domain_irq+0x7c/0xec)
[<c0199888>] (__handle_domain_irq) from [<c04ac298>] (gic_handle_irq+0x58/0x9c)
[<c04ac298>] (gic_handle_irq) from [<c0101ab0>] (__irq_svc+0x70/0xb0)
Exception stack(0xe73ddc60 to 0xe73ddca8)
...
[<c0101ab0>] (__irq_svc) from [<c01967d8>] (console_unlock+0x5a8/0x6a8)
[<c01967d8>] (console_unlock) from [<c01981d0>] (vprintk_emit+0x118/0x2d8)
[<c01981d0>] (vprintk_emit) from [<c01983b0>] (vprintk_default+0x20/0x28)
[<c01983b0>] (vprintk_default) from [<c01989b4>] (printk+0x30/0x54)
[<c01989b4>] (printk) from [<c07500b8>] (s5p_mfc_init_decode_v6+0x1d4/0x284)
[<c07500b8>] (s5p_mfc_init_decode_v6) from [<c07230d0>] (vb2_start_streaming+0x24/0x150)
[<c07230d0>] (vb2_start_streaming) from [<c0724e4c>] (vb2_core_streamon+0x11c/0x15c)
[<c0724e4c>] (vb2_core_streamon) from [<c07478b8>] (vidioc_streamon+0x64/0xa0)
[<c07478b8>] (vidioc_streamon) from [<c0709640>] (__video_do_ioctl+0x28c/0x45c)
[<c0709640>] (__video_do_ioctl) from [<c0709bc8>] (video_usercopy+0x260/0x8a4)
[<c0709bc8>] (video_usercopy) from [<c02b3820>] (do_vfs_ioctl+0xb0/0x9fc)
[<c02b3820>] (do_vfs_ioctl) from [<c02b41a0>] (ksys_ioctl+0x34/0x58)
[<c02b41a0>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xe73ddfa8 to 0xe73ddff0)
...
---[ end trace 376cf5ba6e0bee93 ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If vpif_probe() fails on v4l2_device_register() and vpif_probe_complete(),
then memory allocated at initialize_vpif() for global vpif_obj.dev[i]
become unreleased.
The patch adds deallocation of vpif_obj.dev[i] on the error path.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When building with CONFIG_VIDEO_CODA and CONFIG_CODA_FS enabled as
loadable modules, we see the following warning:
fs/coda/coda.ko
drivers/media/platform/coda/coda.ko
Rework so media/platform/coda is named coda-vpu. Leaving CODA_FS as is
since that's a well known module.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
New Gen3 R-Car platforms incorporate the FDP1 with an updated version
register. No code change is required to support these targets, but they
will currently report an error stating that the device can not be
identified.
Update the driver to match against the new device types.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
XCMhQ9s=
=cb80
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc4' into media/master
There are some conflicts due to SPDX changes. We also have more
patches being merged via media tree touching them.
So, let's merge back from upstream and address those.
Linux 5.2-rc4
* tag 'v5.2-rc4': (767 commits)
Linux 5.2-rc4
MAINTAINERS: Karthikeyan Ramasubramanian is MIA
i2c: xiic: Add max_read_len quirk
lockref: Limit number of cmpxchg loop retries
uaccess: add noop untagged_addr definition
x86/insn-eval: Fix use-after-free access to LDT entry
kbuild: use more portable 'command -v' for cc-cross-prefix
s390/unwind: correct stack switching during unwind
block, bfq: add weight symlink to the bfq.weight cgroup parameter
cgroup: let a symlink too be created with a cftype file
drm/nouveau/secboot/gp10[2467]: support newer FW to fix SEC2 failures on some boards
drm/nouveau/secboot: enable loading of versioned LS PMU/SEC2 ACR msgqueue FW
drm/nouveau/secboot: split out FW version-specific LS function pointers
drm/nouveau/secboot: pass max supported FW version to LS load funcs
drm/nouveau/core: support versioned firmware loading
drm/nouveau/core: pass subdev into nvkm_firmware_get, rather than device
block: free sched's request pool in blk_cleanup_queue
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
...
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Correctly handle stopping and restarting the encoder, keeping
track of the stop and drain states.
In addition it adds correct handling of corner cases, allowing
v4l2-compliance to pass.
Unfortunately, the code is getting to be quite complicated, so
we need to work on better codec support in v4l2-mem2mem.c to
simplify drivers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return an error when attempting to subscribe to those events
for a stateless codec.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After a resolution change is detected, q_data->sizeimage is updated
to the new format, but buf_prepare is still draining buffers that
need to use the old pre-resolution-change value. So store the sizeimage
value in q_data->vb2_sizeimage in queue_setup and use that in
buf_prepare.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set V4L2_BUF_FLAG_P/KEYFRAME after decoding a frame.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stateful encoder requires the presence of this control.
Since a single buffer is sufficient for vicodec, we just
set this control to 1.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Setting the encoder output format to e.g. 1920x1080 will set the
crop rectangle to 1920x1088, the coded resolution to 1920x1088 and
the capture coded resolution and sizeimage to 1920x1088 as well.
Note that this might change, since the encoder spec is still in
flux with respect to how this should behave.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The initial sizeimage value was wrong for the stateless decoder.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rather than returning width/height values of 0, just default to
a format. Formats in V4L2 are always supposed to be valid, there
is no concept of an invalid format.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_ctrl_request_complete can sleep, so can't be called while
a spinlock is held.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since locking is handled by regmap, the spin_lock_irqsave() in the
meson_ao_cec_g12a_read/write() regmap callbacks is not needed.
Fixes: b7778c4668 ("media: platform: meson: Add Amlogic Meson G12A AO CEC Controller driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of watchdog timeout detected while doing mode detection,
it's better triggering video engine hardware reset immediately so
this commit fixes code for the case. Other than the case, it will
trigger video engine hardware reset after RESOLUTION_CHANGE_DELAY.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are cases that interrupt bits are cleared by a 500ms delayed
work which causes unnecessary irq calls. Also, the current
interrupt handler returns IRQ_HANDLED always but it should return
IRQ_NONE if there is any unhandled interrupt. So this commit
refines the interrupt handling logic to fix these issues.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VE_INTERRUPT_CAPTURE_COMPLETE and VE_INTERRUPT_COMP_COMPLETE are
not set at the same time but the current interrupt handling
mechanism of this driver doesn't clear the interrupt flag until
both two are set, and this behavior causes unnecessary interrupt
handler calls. In fact, this driver provides JPEG format only so
taking care of the VE_INTERRUPT_COMP_COMPLETE is enough for getting
compressed image frame so this commit gets rid of the
VE_INTERRUPT_CAPTURE_COMPLETE checking logic to simplify the logic.
Handling of VE_INTERRUPT_CAPTURE_COMPLETE could be added back later
when it's actually needed.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver prints out too much log messages when a
mode change happens, video turned off by screen saver and etc.
Actually, all cases are reported to user space properly. Also,
these are not critical errors but recoverable things, so this
commit changes the log level of some noisy printing outs.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Video Engine has a dedicated interrupt line so this driver doesn't
need to use IRQF_SHARED flag so remove it. Also, it'd be good for
following what Thomas recommended in the IRQF_ONESHOT support
patch like below:
"Note that for now IRQF_ONESHOT cannot be used with IRQF_SHARED to
avoid complex accounting mechanisms."
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Differently from other Aspeed drivers, this driver calls clock
control APIs in interrupt context. Since ECLK is coupled with a
reset bit in clk-aspeed module, aspeed_clk_enable will make 10ms of
busy waiting delay for triggering the reset and it will eventually
disturb other drivers' interrupt handling. To fix this issue, this
commit changes this driver's irq to threaded irq so that the delay
can be happened in a thread context.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver calls clk_prepare and clk_unprepare from
interrupt context too but these should be called from sleepable
context only. To fix this issue, this commit splits out
clk_enable/disable and clk_prepare/unprepare, and it places
clk_prepare/unprepare calls into the module probe/remove function.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The assigment of FB_VMODE_NONINTERLACE to var->vmode should be a
bit-wise or of FB_VMODE_NONINTERLACE instead of an assignment,
otherwise the previous clearing of the FB_VMODE_MASK bits of
var->vmode makes no sense and is redundant.
Addresses-Coverity: ("Unused value")
Fixes: ad4e02d508 ("[media] vivid: add a simple framebuffer device for overlay testing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
MT8183 will use a multi-planar format backed by a single buffer. Adapt
the existing code to be able to handle such frames instead of assuming
each frame is backed by two buffers.
Co-developed-by: Alexandre Courbot <acourbot@chromium.org>
[acourbot: refactor, cleanup and split]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch alignment warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Formats are read-only internal memory structures, so make them const.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Replace the GPLv2 boilerplate with the corresponding SPDX reference.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Change the way subdevices check if the stream is running. Verify the stream
pointer instead of src_frame. This makes easier to get rid of the void* and
u8* that points to frames in the subdevices structs.
Remove checks that s_stream does on subdevices. They are redundant since
the Media Controller Framework doesn't allow two streaming on the same
media pipeline at the same time.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you may redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190116.162794791@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
distributable under the terms of the gnu general public license
version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081035.495262081@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 this program is distributed
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more
details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.889824453@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 this program is distributed
in the hope that it will be useful but without any warranty without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more
details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 97 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.025053186@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new helper functions for the try_de/decoder_cmd ioctls.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support for multiplanar and singleplanar formats is mutually exclusive,
at least in practice. In our attempt to unify support for support for
mplane and !mplane in v4l, let's get rid of the
->vidioc_enum_fmt_{vid,out}_cap_mplane() hooks and call
->vidioc_enum_fmt_{vid,out}_cap() instead.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[hverkuil-cisco@xs4all.nl: fix typos: pirv -> priv and prov -> priv]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is needed if we want the core to be able to check _MPLANE support
without having to call the ->vidioc_querycap() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file may be distributed under the terms of the gnu general
public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.395589349@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
video_unregister_device() can be called on a never or an already
unregistered device. Drop the redundant check.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm functions are fine for managing resources that are directly related
to the device at hand and that have no other dependencies. However, a
process holding a file handle to a device created by a driver for a device
may result in the file handle left behind after the device is long gone.
This will result in accessing released (and potentially reallocated)
memory.
Instead, manage the memory resources in the driver. Releasing the
resources can be later on bound to e.g. by releasing a reference.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch replaces bit shifting on 1 with the BIT(x) macro.
This was done with coccinelle:
@@
constant c;
@@
-1 << c
+BIT(c)
[mchehab+samsung@kernel.org: rebase on the top of upstream]
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The A83T SoC has a camera sensor interface (known as CSI in Allwinner
lingo), which is similar to the one found on the A64 and H3. The only
difference seems to be that support of MIPI CSI through a connected
MIPI CSI-2 bridge.
Add support for this variant.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The call to of_find_device_by_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_pm.c:60:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 38, but without a corresponding object release within this function.
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_pm.c:63:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 38, but without a corresponding object release within this function.
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_pm.c:72:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 38, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/mtk-vpu/mtk_vpu.c:477:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 464, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use v4l2_m2m2_buf_copy_metadata to let BIT encoder contexts copy buffer
field, timestamp, timestamp flags, and optionally timecode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
coda_command_sync, coda_hw_reset, and __coda_start_decoding
all expect to be called under the coda_mutex device lock.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The MPEG-2 decoder firmware reports profile and level indication that
can be used to set V4L2 MPEG-2 profile and level controls
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The MPEG-4 decoder firmware reports profile and level indication values
that can be used to update V4L2 MPEG-4 profile and level controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The other subdevice implementations in vimc (debayer and scaler) which
share their code structure with the sensor do not have an explicit
return statement at the end of the s_stream(0) code path. Align the
sensor subdevice by dropping the return statement.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the system has other devices being registered in the component
framework, the compare function will be called with a device that
doesn't belong to vimc.
This device is not necessarily a platform_device, nor have a
platform_data (which causes a NULL pointer dereference error) and if it
does have a pdata, it is not necessarily type of struct vimc_platform_data.
So casting to any of these types is wrong.
Instead of expecting a given pdev with a given pdata, just expect for
the device it self. vimc-core is the one who creates them, we know in
advance exactly which object to expect in the match.
Fixes: 4a29b70907 ("[media] vimc: Subdevices as modules")
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vim2m_device_release() will be called by video_unregister_device() to release
various objects.
There are two double-free issue,
1. dev->m2m_dev will be freed twice in error_m2m path/vim2m_device_release
2. the error_v4l2 and error_free path in vim2m_probe() will release
same objects, since vim2m_device_release has done.
Fixes: ea6c7e34f3 ("media: vim2m: replace devm_kzalloc by kzalloc")
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Unbinding the driver while streaming caused the driver to hang.
The cause of this was failing to use the v4l2_device release
function and the use of devm_kmalloc for the state structure.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This commit clears the interrupt reason (INT_REASON) register
on the interrupt handler. Without this clearing, the CODA hardware
has been observed to get completely stalled on CODA980 variants,
requiring a pretty deep hardware reset.
The datasheet specifies that the INT_REASON register is set
by the CODA hardware, and should be cleared by the host.
While the CODA versions that are currently supported by this driver
don't seem to need this change, it's a really small change,
so it seems a wise thing to do to avoid hitting some
rare race-condition in the hardware.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current interrupt handler is doing very little, and not doing
any non-atomic operations. Pretty much all it does is accessing
a couple registers, taking a couple spinlocks and then signalling
a completion.
There is no reason this should be a threaded interrupt handler,
so move the handler to regular hard interrupt context.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The mutex unlock in the threaded interrupt handler is not paired
with any mutex lock. Remove it.
This bug has been here for a really long time, so it applies
to any stable repo.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is just a cosmetic change to print a more descriptive
message, to distinguish decoder from encoder:
So, instead of printing
coda 2040000.vpu: codec registered as /dev/video[4-5]
With this change, the driver now prints
coda 2040000.vpu: encoder registered as /dev/video4
coda 2040000.vpu: decoder registered as /dev/video5
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These two slice modes used by the V4L2_CID_MPEG_VIDEO_MULTI_SLICE_MODE
control had a silly typo:
V4L2_MPEG_VIDEO_MULTI_SICE_MODE_MAX_MB
V4L2_MPEG_VIDEO_MULTI_SICE_MODE_MAX_BYTES
SICE should be SLICE.
Rename these enum values, keeping the old ones (under #ifndef __KERNEL__)
for backwards compatibility reasons.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlzrJgUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1XAIAJajJpeKc9MVQipi
zWiI+WgHDg8gG/HnLKzP2Zp4MUjTCz30t0rnBbdo6AyK6LnPBL53yxg9q64XN7vI
p/h2ys+/DvqhIYSPWX6C++HYQT4Cb5ghxJABEIsztd3G4nfB9L2vgq9zKSNFusTD
UtfUxufciZPX515TuE4IqWMwS4Ut5daH7V3jjZunhPiayTFv64e1KbpKLLzHR0NR
DfFbrPcdp7VyCT/A5AKrqfqeB6O9dm/Fe4CsdsaKuzASCXJ6GUc/A7iZDndv/KA4
f5Xh7SGlQ2TfT1ud/aMfdw3AcMjqB8zgMJenovJ7UuHDfULBWNeAmMh/cTDwY9eY
Xgyvfm0=
=S8p9
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc2' into patchwork
Merge back from upstream into media tree, as there are some
patches merged upstream that has pontential of causing
conflicts (one actually rised a conflict already).
Linux 5.2-rc2
* tag 'v5.2-rc2': (377 commits)
Linux 5.2-rc2
random: fix soft lockup when trying to read from an uninitialized blocking pool
tracing: Silence GCC 9 array bounds warning
ext4: fix dcache lookup of !casefolded directories
locking/lock_events: Use this_cpu_add() when necessary
KVM: x86: fix return value for reserved EFER
tools/kvm_stat: fix fields filter for child events
KVM: selftests: Wrap vcpu_nested_state_get/set functions with x86 guard
kvm: selftests: aarch64: compile with warnings on
kvm: selftests: aarch64: fix default vm mode
kvm: selftests: aarch64: dirty_log_test: fix unaligned memslot size
KVM: s390: fix memory slot handling for KVM_SET_USER_MEMORY_REGION
KVM: x86/pmu: do not mask the value that is written to fixed PMUs
KVM: x86/pmu: mask the result of rdpmc according to the width of the counters
x86/kvm/pmu: Set AMD's virt PMU version to 1
KVM: x86: do not spam dmesg with VMCS/VMCB dumps
kvm: Check irqchip mode before assign irqfd
kvm: svm/avic: fix off-by-one in checking host APIC ID
KVM: selftests: do not blindly clobber registers in guest asm
KVM: selftests: Remove duplicated TEST_ASSERT in hyperv_cpuid.c
...
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/qcom/venus/firmware.c:90:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 82, but without a corresponding object release within this function.
drivers/media/platform/qcom/venus/firmware.c:94:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 82, but without a corresponding object release within this function.
drivers/media/platform/qcom/venus/firmware.c:128:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 82, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Drop the reference to "parallel-ports" and remote endpoint's parent
nodes obtained previously with of_get_child_by_name() and
of_get_parent() respectively.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clean up of resources should be in reverse order of vpss_init().
Fix this inside vpss_exit().
Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove the header search path to the current directory.
The compiler will search headers in the current directory by
using #include "..." instead of #include <...>
Also, change TRACE_INCLUDE_PATH to point to the location of trace.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The commit
05fed81625 ("[media] marvell-ccic: add MIPI support for marvell-ccic driver")
that claimed to add CSI2 turned on C0_EOF_VSYNC for parallel bus
without a very good explanation.
That broke camera on OLPC XO-1.75 which precisely uses a sensor on a
parallel bus. Revert that chunk.
Tested on an OLPC XO-1.75.
Fixes: 05fed81625 ("[media] marvell-ccic: add MIPI support for marvell-ccic driver")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The commit d790b7eda9 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
left dma_desc_nent unset. It previously contained the number of DMA
descriptors as returned from dma_map_sg().
We can now (since the commit referred to above) obtain the same value from
the sg_table and drop dma_desc_nent altogether.
Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe
driver, since that one doesn't do DMA.
[mchehab+samsung@kernel.org: fix a checkpatch warning]
Fixes: d790b7eda9 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Due to limitations in gpiolib it was impossible to disable the interrupt of
an input gpio and then switch it to gpio output and drive it. The only way
to achieve that was to free the interrupt first, then switch the direction.
When going back to gpio input and using interrupts to read the gpio pin you
had to request the irq again.
This limitation was lifted in gpiolib in kernel 4.20, but the cec-gpio driver
was still using the old workaround implementation.
This patch updates the cec-gpio driver to just enable and disable the irq.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Venus v4 doesn't send ALLOC_MODE property and thus parser doesn't
recognize it as dynamic buffer (for OUTPUT/OUTPUT2 type of buffers)
make it obvious in the helper function.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Patch commit de5a0bafcf ("media: venus: core: correct maximum hardware
load for sdm845") meant to increase the maximum hardware load for sdm845,
but ended up changing the one for msm8996 instead.
Fixes: de5a0bafcf ("media: venus: core: correct maximum hardware load for sdm845")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The header report return value from decoder sequence initialization is
available on CodaHx4 and CODA7541 already. Use the profile and level
identification values reported by the firmware to update codec specific
profile and level controls after sequence initialization has succeeded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When a menu control is updated via s_ctrl, print the corresponding menu
entry string in addition to the numerical value it is set to.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Otherwise the default initialization would always swamp the debug log.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Print a single line containing the following information:
- which frame was decoded, including its type,
- if no frame was decoded, the reason (code) why
- which decoded frame was returned, copied out by either rotator or VODA,
- if no frame was returned, the reason (code) why, and
- the output queue sequence number, which is only useful in case
each queued coded buffer corresponds to exactly one frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a function to translate from V4L2 buffer flags to 'I'/'P'/'B'
characters for debug output.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This allows to use coda_debug level 2 for verbose but not quite as
verbose debug logging. Register access level logging is of limited
use anyway, as this includes busy polling of status bits.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case the sensor refuses to set the format, avoid printing the error
message that no compatible format was found.
This means that the try_fmt will be less verbose.
The error will be printed only if really a format cannot be found.
Some application try all possible formats in a row (gstreamer e.g.)
which will flood the console with error messages until a working one is found.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds support for the 'button' control DO_WHITE_BALANCE
This feature will enable the ISC to compute the white balance coefficients
in a one time shot, at the user discretion.
This can be used if a color chart/grey chart is present in front of the camera.
The ISC will adjust the coefficients and have them fixed until next balance
or until sensor mode is changed.
This is particularly useful for white balance adjustment in different
lighting scenarios, and then taking photos to similar scenery.
The old auto white balance stays in place, where the ISC will adjust every
4 frames to the current scenery lighting, if the scenery is approximately
grey in average, otherwise grey world algorithm fails.
One time white balance adjustments needs streaming to be enabled, such that
capture is enabled and the histogram has data to work with.
Histogram without capture does not work in this hardware module.
To start the one time white balance procedure:
v4l2-ctl --set-ctrl=do_white_balance=1
This feature works only if the sensor is streaming RAW data, as the hardware
supports a histogram only for RAW bayer components.
If the auto white balance is enabled, do_white_balance does nothing.
If the streaming is disabled, or the sensor does not output RAW data, the
control is inactive.
User controls now include the do_white_balance ctrl:
User Controls
brightness 0x00980900 (int) : min=-1024 max=1023 step=1 default=0 value=0 flags=slider
contrast 0x00980901 (int) : min=-2048 max=2047 step=1 default=256 value=256 flags=slider
white_balance_automatic 0x0098090c (bool) : default=1 value=0
do_white_balance 0x0098090d (button) : flags=write-only, execute-on-write
gamma 0x00980910 (int) : min=0 max=2 step=1 default=2 value=2 flags=slider
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reworked auto white balance feature (awb) to cope with all four channels.
Implemented stretching and grey world algorithms.
Using the histogram, the ISC will auto adjust the white balance during
frame captures.
Because each histogram needs a frame, it will take 4 frames for one adjustment.
When the gains were updated by previous code, the registers for the gains
were updated only on new streaming start. Now, after each full histogram the
registers are updated with new gains.
Also, on previous code, if the streaming stopped but not all 3 histograms
finished, a new histogram was started either way. This used to lead to an
error "timeout to update profile" when streaming was stopped.
According to the hardware, histogram can only work together with the capture,
not independently.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5b
("kbuild: do not drop -I without parameter").
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=M94t
-----END PGP SIGNATURE-----
Merge tag 'media/v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some fixes for some platform drivers (rockchip, atmel, omap, daVinci,
tegra-cec, coda and rcar).
Also includes a fix on one of the V4L2 uAPI doc, explaining a border
case"
* tag 'media/v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: rockchip/vpu: Fix/re-order probe-error/remove path
media: rockchip/vpu: Initialize mdev->bus_info
media: rockchip/vpu: Get vdev from the file arg in vidioc_querycap()
media: rockchip/vpu: Add missing dont_use_autosuspend() calls
media: rockchip/vpu: Do not request id 0 for our video device
media: tegra-cec: fix cec_notifier_parse_hdmi_phandle return check
media: davinci/vpbe: array underflow in vpbe_enum_outputs()
media: field-order.rst: clarify FIELD_ANY and FIELD_NONE
media: staging/imx: add media device to capture register
media: rcar-csi2: Propagate the FLD signal for NTSC and PAL
media: rcar-csi2: restart CSI-2 link if error is detected
media: omap_vout: potential buffer overflow in vidioc_dqbuf()
media: coda: fix unset field and fail on invalid field in buf_prepare
media: atmel: atmel-isc: fix asd memory allocation
media: atmel: atmel-isc: fix INIT_WORK misplacement
media: atmel: atmel-isc: limit incoming pixels per frame
-----BEGIN PGP SIGNATURE-----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=YFiQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This has two exciting community drivers for ARM Mali accelerators.
Since ARM has never been open source friendly on the GPU side of the
house, the community has had to create open source drivers for the
Mali GPUs. Lima covers the older t4xx and panfrost the newer 6xx/7xx
series. Well done to all involved and hopefully this will help ARM
head in the right direction.
There is also now the ability if you don't have any of the legacy
drivers enabled (pre-KMS) to remove all the pre-KMS support code from
the core drm, this saves 10% or so in codesize on my machine.
i915 also enable Icelake/Elkhart Lake Gen11 GPUs by default, vboxvideo
moves out of staging.
There are also some rcar-du patches which crossover with media tree
but all should be acked by Mauro.
Summary:
uapi changes:
- Colorspace connector property
- fourcc - new YUV formts
- timeline sync objects initially merged
- expose FB_DAMAGE_CLIPS to atomic userspace
new drivers:
- vboxvideo: moved out of staging
- aspeed: ASPEED SoC BMC chip display support
- lima: ARM Mali4xx GPU acceleration driver support
- panfrost: ARM Mali6xx/7xx Midgard/Bitfrost acceleration driver support
core:
- component helper docs
- unplugging fixes
- devm device init
- MIPI/DSI rate control
- shmem backed gem objects
- connector, display_info, edid_quirks cleanups
- dma_buf fence chain support
- 64-bit dma-fence seqno comparison fixes
- move initial fb config code to core
- gem fence array helpers for Lima
- ability to remove legacy support code if no drivers requires it (removes 10% of drm.ko size)
- lease fixes
ttm:
- unified DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
panel:
- OSD070T1718-19TS panel support
- panel-tpo-td028ttec1 backlight support
- Ronbo RB070D30 MIPI/DSI
- Feiyang FY07024DI26A30-D MIPI-DSI panel
- Rocktech jh057n00900 MIPI-DSI panel
i915:
- Comet Lake (Gen9) PCI IDs
- Updated Icelake PCI IDs
- Elkhartlake (Gen11) support
- DP MST property addtions
- plane and watermark fixes
- Icelake port sync and VEBOX disable fixes
- struct_mutex usage reduction
- Icelake gamma fix
- GuC reset fixes
- make mmap more asynchronous
- sound display power well race fixes
- DDI/MIPI-DSI clocks for Icelake
- Icelake RPS frequency changing support
- Icelake workarounds
amdgpu:
- Use HMM for userptr
- vega20 experimental smu11 support
- RAS support for vega20
- BACO support for vega12 + fixes for vega20
- reworked IH interrupt handling
- amdkfd RAS support
- Freesync improvements
- initial timeline sync object support
- DC Z ordering fixes
- NV12 planes support
- colorspace properties for planes=
- eDP opts if eDP already initialized
nouveau:
- misc fixes
etnaviv:
- misc fixes
msm:
- GPU zap shader support expansion
- robustness ABI addition
exynos:
- Logging cleanups
tegra:
- Shared reset fix
- CPU cache maintenance fix
cirrus:
- driver rewritten using simple helpers
meson:
- G12A support
vmwgfx:
- Resource dirtying management improvements
- Userspace logging improvements
virtio:
- PRIME fixes
rockchip:
- rk3066 hdmi support
sun4i:
- DSI burst mode support
vc4:
- load tracker to detect underflow
v3d:
- v3d v4.2 support
malidp:
- initial Mali D71 support in komeda driver
tfp410:
- omap related improvement
omapdrm:
- drm bridge/panel support
- drop some omap specific panels
rcar-du:
- Display writeback support"
* tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm: (1507 commits)
drm/msm/a6xx: No zap shader is not an error
drm/cma-helper: Fix drm_gem_cma_free_object()
drm: Fix timestamp docs for variable refresh properties.
drm/komeda: Mark the local functions as static
drm/komeda: Fixed warning: Function parameter or member not described
drm/komeda: Expose bus_width to Komeda-CORE
drm/komeda: Add sysfs attribute: core_id and config_id
drm: add non-desktop quirk for Valve HMDs
drm/panfrost: Show stored feature registers
drm/panfrost: Don't scream about deferred probe
drm/panfrost: Disable PM on probe failure
drm/panfrost: Set DMA masks earlier
drm/panfrost: Add sanity checks to submit IOCTL
drm/etnaviv: initialize idle mask before querying the HW db
drm: introduce a capability flag for syncobj timeline support
drm: report consistent errors when checking syncobj capibility
drm/nouveau/nouveau: forward error generated while resuming objects tree
drm/nouveau/fb/ramgk104: fix spelling mistake "sucessfully" -> "successfully"
drm/nouveau/i2c: Disable i2c bus access after ->fini()
drm/nouveau: Remove duplicate ACPI_VIDEO_NOTIFY_PROBE definition
...
cec_notifier_parse_hdmi_phandle returns an error pointer, not a NULL
pointer on error.
Fixes: 4d34c9267d: ("media: tegra_cec: use new cec_notifier_parse_hdmi_phandle helper")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In vpbe_enum_outputs() we check if (temp_index >= cfg->num_outputs) but
the problem is that "temp_index" can be negative. This patch changes
the types to unsigned to address this array underflow bug.
Fixes: 66715cdc32 ("[media] davinci vpbe: VPBE display driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Depending on which video standard is used the driver needs to setup the
hardware to correctly handle fields. If stream is identified as NTSC
or PAL setup field detection and propagate the field detection signal.
Later versions of the datasheet have been updated to make it clear
that FLD register should be set to 0 when dealing with non-interlaced
field formats.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Restart the CSI-2 link if the CSI-2 receiver detects an error during
reception. The driver did nothing when a link error happened and the
data flow simply stopped without the user knowing why.
Change the driver to try and recover from errors by restarting the link
and informing the user that something is not right. For obvious reasons
it's not possible to recover from all errors (video source disconnected
for example) but in such cases the user is at least informed of the
error and the same behavior of the stopped data flow is retained.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The "b->index" is a u32 the comes from the user in the ioctl. It hasn't
been checked. We aren't supposed to use it but we're instead supposed
to use the value that gets written to it when we call videobuf_dqbuf().
The videobuf_dqbuf() first memsets it to zero and then re-initializes it
inside the videobuf_status() function. It's this final value which we
want.
Hans Verkuil pointed out that we need to check the return from
videobuf_dqbuf(). I ended up doing a little cleanup related to that as
well.
Fixes: 72915e851d ("[media] V4L2: OMAP: VOUT: dma map and unmap v4l2 buffers in qbuf and dqbuf")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance likes to queue a buffer with field set to V4L2_FIELD_ANY
and expects it to be returned corrected to a valid field.
Follow vicodec in handling this in the buf_prepare callback.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The subsystem will free the asd memory on notifier cleanup, if the asd is
added to the notifier.
However the memory is freed using kfree.
Thus, we cannot allocate the asd using devm_*
This can lead to crashes and problems.
To test this issue, just return an error at probe, but cleanup the
notifier beforehand.
Fixes: 106267444f ("[media] atmel-isc: add the Image Sensor Controller code")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case the completion function failes, unbind will be called
which will call cancel_work for awb_work.
This will trigger a WARN message from the workqueue.
To avoid this, move the INIT_WORK call at the start of the completion
function. This way the work is always initialized, which corresponds
to the 'always canceled' unbind code.
Fixes: 93d4a26c3d ("[media] atmel-isc: add the isc pipeline function")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will limit the incoming pixels per frame from the sensor.
Currently, the ISC will stop sampling the frame only when the vsync/hsync
are detected.
If we misconfigure the resolution in the sensor w.r.t. resolution in the ISC,
the buffer used for DMA in the ISC will be smaller than the number of pixels
that the ISC DMA engine will copy.
In this case it happens that the DMA will overwrite parts of the memory which
should not be written, leading to memory corruption.
To avoid this situation, use the PFE CFG1 and PFE CFG2 registers, which crop
the incoming frame to the resolution that we configure.
This way the DMA engine will never write more data than we expect it to.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reserved memory doesn't need to be required; system memory would work
fine.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The reset line is toggled by enabling the clocks, so it's not necessary
to manually toggle the reset as well.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
During probe, return the provided errors value instead of -ENODEV.
This allows the driver to be deferred probed if needed.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the V4L2_PIX_FMT_RGBA555, V4L2_PIX_FMT_RGBX555,
V4L2_PIX_FMT_ABGR555, V4L2_PIX_FMT_XBGR555, V4L2_PIX_FMT_BGRA555 and
V4L2_PIX_FMT_BGRX555 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the V4L2_PIX_FMT_RGBA444, V4L2_PIX_FMT_RGBX444,
V4L2_PIX_FMT_ABGR444, V4L2_PIX_FMT_XBGR444, V4L2_PIX_FMT_BGRA444 and
V4L2_PIX_FMT_BGRX444 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the V4L2_PIX_FMT_BGRA32, V4L2_PIX_FMT_BGRX32,
V4L2_PIX_FMT_RGBA32 and V4L2_PIX_FMT_RGBX32 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Amlogic G12A SoC embeds a second CEC controller with a totally
different design.
The two controller can work in the same time since the CEC line can
be set to two different pins on the two controllers.
This second CEC controller is documented as "AO-CEC-B", thus the
registers will be named "CECB_" to differentiate with the other
AO-CEC driver.
Unlike the other AO-CEC controller, this one takes the Oscillator
clock as input and embeds a dual-divider to provide a precise
32768Hz clock for communication. This is handled by registering
a clock in the driver.
Unlike the other AO-CEC controller, this controller supports setting
up to 15 logical addresses and supports the signal_free_time settings
in the transmit function.
Unfortunately, this controller does not support "monitor" mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CrosEC CEC driver never decremented the HDMI device refcount.
CEC drivers only need the HDMI device pointer as a key in the
notifier list, it never accesses the device, so there is no
need to keep a reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SECO CEC driver never decremented the HDMI device refcount.
CEC drivers only need the HDMI device pointer as a key in the
notifier list, it never accesses the device, so there is no
need to keep a reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Tegra CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The STI CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The S5P CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The meson CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I previously added an RC_CORE dependency here, but missed the corner
case of CONFIG_VIDEO_SECO_CEC=y with CONFIG_RC_CORE=m, which still
causes a link error:
drivers/media/platform/seco-cec/seco-cec.o: In function `secocec_probe':
seco-cec.c:(.text+0x1b8): undefined reference to `devm_rc_allocate_device'
seco-cec.c:(.text+0x2e8): undefined reference to `devm_rc_register_device'
drivers/media/platform/seco-cec/seco-cec.o: In function `secocec_irq_handler':
seco-cec.c:(.text+0xa2c): undefined reference to `rc_keydown'
Refine the dependency to disallow building the RC subdriver in this case.
This is the same logic we apply in other drivers like it.
Fixes: f27dd0ad68 ("media: seco-cec: fix RC_CORE dependency")
Cc: <stable@vger.kernel.org> # 5.1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later datasheet versions (rev 1.00) clarifies that the FLD register
should be set after LINKCNT.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Latest information from hardware engineers reveals that H3 ES2 and ES3
behave differently when working with link speeds bellow 250 Mpbs.
Add a SoC match for H3 ES2.* and use the correct startup sequence.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The latest datasheet (rev 1.50) updates the start procedure for V3M and
E3. Update the driver to match these changes.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later versions of the datasheet updates the reset procedure to more
closely resemble the standby mode. Update the driver to enter and exit
the standby mode instead of resetting the hardware before and after
streaming is started and stopped. This replaces the software reset
(SRST.SRST) control.
While at it break out the full start and stop procedures from
rcsi2_s_stream() into the existing helper functions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If VIDIOC_CREATE_BUFS is called with a sizeimage smaller than the
queue sizeimage, fail with -EINVAL instead of correcting the size
and continuing without error. This is required by v4l2-compliance.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance sets colorimetry on the output queue and then verifies
that querying colorimetry on the capture queue returns the same
configuration. For this to work, the encoder must allow setting context
colorimetry parameters on the output queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stateful encoder API requires VIDIOC_ENUM_FRAMESIZES to be
implemented.
Allow enumeration of supported frame sizes for encoding.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return -ENOTTY when userspace tries to call VIDIOC_(TRY_)ENCODER_CMD on
a decoder instance or VIDIOC_(TRY_)DECODER_CMD on an encoder instance.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add min number of buffers for capture (decoder) and output (encoder)
controls, which are required by the stateful video decoder / encoder
interface specification.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The error return value is not written by some firmware codecs, such as
MPEG-2 decode on CodaHx4. Clear the error return value before starting
the picture run to avoid misinterpreting unrelated values returned by
sequence initialization as error return value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since levels are specified in terms of maximum values, there is no
reason to filter out lower levels than the supported maximum.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The chosen codec depends on the coded format, which is known as soon as
the S_FMT call on the coded queue. This allows to use the codec in
callbacks that may be called before start_streaming, such as buf_queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
syzkaller reported crashes on kfree() called from
vivid_vid_cap_s_selection(). This looks like a simple typo, as
dev->bitmap_cap is allocated with vzalloc() throughout the file.
Fixes: ef834f7836 ("[media] vivid: add the video capture and output
parts")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reported-by: Syzbot <syzbot+6c0effb5877f6b0344e2@syzkaller.appspotmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Update referenced frame buffer's reference count when playing vp9
content which has show_existing_frame flag, and copy enough buffer
data to current shown frame.
Signed-off-by: Maoguang Meng <maoguang.meng@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Do not access sd_formats[] if num_of_sd_formats is zero, ie
subdev sensor didn't expose any formats.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Report overrun error only when it exceeds a given threshold.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Enlarge the plane number to support more complex case
and add the support for fmt change case.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Media bus codes were being mapped to pixelformats, which causes a
limitation on vimc because not all pixelformats can be mapped to media
bus codes.
Also, media bus codes are an internal configuration from the device.
Userspace only assures media bus codes matches between pads and expects
the image in a given pixelformat. So we can allow almost any media bus
format to be configured between pads, except for debayer that expects a
media bus code of type bayer in the sink pad.
[hverkuil-cisco@xs4all.nl: drop use of v4l2_get_fourcc_name: not yet available]
[hverkuil-cisco@xs4all.nl: made vimc_mbus_list static]
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is mandatory to write CEC_CFGR only when CECEN=0. To protect
transmission, a check have been added to delayed logical address
modification. This patch is necessary tp pass all tests of compliance.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ISC will output the "ARGB32" configuration in byte order: B, G, R, Alpha.
This is in fact the format BGRA, aka ABGR32.
If alpha is missing, the same format is equivalent to XBGR32.
Added both formats and removed ARGB32 which is wrong.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This change is a redesign in the formats and the way the ISC is
configured w.r.t. sensor format and the output format from the ISC.
I have changed the splitting between sensor output (which is also ISC input)
and ISC output.
The sensor format represents the way the sensor is configured, and what ISC
is receiving.
The format configuration represents the way ISC is interpreting the data and
formatting the output to the subsystem.
Now it's much easier to figure out what is the ISC configuration for input, and
what is the configuration for output.
The non-raw format can be obtained directly from sensor or it can be done
inside the ISC. The controller format list will include a configuration for
each format.
The old supported formats are still in place, if we want to dump the sensor
format directly to the output, the try format routine will detect and
configure the pipeline accordingly.
This also fixes the previous issues when the raw format was NULL which
resulted in many crashes for sensors which did not have the expected/tested
formats.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The strncpy() function is being deprecated upstream. Replace
it by the safer strscpy().
While here, replace a few occurences of strlcpy() that were
recently added to also use strscpy().
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The support for those two formats are archtecture-dependent.
Use the endianness to CPU macros to do it right.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm_kcalloc may fail and return a null pointer. The fix returns
-ENOMEM upon failures to avoid null pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This member is never read throughout the code, so remove it.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions by changing a few local variables from vb2_buffer to
vb2_v4l2_buffer. However, it left a few accesses to vb2_buffer::planes
as-is, accidentally turning them into accesses to
vb2_v4l2_buffer::planes and resulting in values being read from/written
to the wrong place.
Fix this by inserting vb2_buf into these accesses so they mimic their
original behavior.
Fixes: 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem buffer helpers")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
clang warns about a possible variable use that gcc never
complained about:
drivers/media/platform/davinci/isif.c:982:32: error: variable 'frame_size' is uninitialized when used here
[-Werror,-Wuninitialized]
dm365_vpss_set_pg_frame_size(frame_size);
^~~~~~~~~~
drivers/media/platform/davinci/isif.c:887:2: note: variable 'frame_size' is declared here
struct vpss_pg_frame_size frame_size;
^
1 error generated.
There is no initialization for this variable at all, and there
has never been one in the mainline kernel, so we really should
not put that stack data into an mmio register.
On the other hand, I suspect that gcc checks the condition
more closely and notices that the global
isif_cfg.bayer.config_params.test_pat_gen flag is initialized
to zero and never written to from any code path, so anything
depending on it can be eliminated.
To shut up the clang warning, just remove the dead code manually,
it has probably never been used because any attempt to do so
would have resulted in undefined behavior.
Fixes: 63e3ab142f ("V4L/DVB: V4L - vpfe capture - source for ISIF driver on DM365")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Smatch warns about small size on two structs:
drivers/media/platform/qcom/venus/hfi_parser.c:103 parse_profile_level() error: memcpy() 'proflevel' too small (8 vs 128)
drivers/media/platform/qcom/venus/hfi_parser.c: drivers/media/platform/qcom/venus/hfi_parser.c:129 parse_caps() error: memcpy() 'cap' too small (16 vs 512)
The reason is that the hfi_parser actually expects:
- multiple data entries on hfi_capabilities
- multiple profile_level on hfi_profile_level_supported
However, the structs trick gcc, making it to believe that
there's just one value for each.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The only way for p_set to be NULL would be if vin_coef_set would be an
empty array.
On such case, the driver will OOPS, as it would try to de-reference a
NULL value. So, the check if p_set is not NULL doesn't make any sense.
Solves those two smatch warnings:
drivers/media/platform/rcar-vin/rcar-dma.c:489 rvin_set_coeff() warn: variable dereferenced before check 'p_set' (see line 484)
drivers/media/platform/rcar-vin/rcar-dma.c:494 rvin_set_coeff() error: we previously assumed 'p_set' could be null (see line 489)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
At the error logic, ipc_buf was already asigned to &ctx->ipc_buf_struct,
with can't be null, as warned by smatch:
drivers/media/platform/sti/delta/delta-ipc.c:223 delta_ipc_open() warn: variable dereferenced before check 'ctx->ipc_buf' (see line 183)
So, remove the uneeded check.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Indentation is odd in several places, especially when printing messages
to the kernel log. Fix it to match the usual coding style.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
for stateless decoder, set the output pixelformat
to V4L2_PIX_FMT_FWHT_STATELESS and the pix info to
pixfmt_stateless_fwht
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implement a stateless decoder for the new node.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: add 'return 0;' before default case in vicodec_try_ctrl()]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add stateless decoder instance field to the dev struct and
register another node for the statelsess decoder.
The stateless API for the node will be implemented in further patches.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix typo: videdev-stateless-dec -> stateless-decoder]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add structs and definitions needed to implement stateless
decoder for fwht and add I/P-frames QP controls to the
public api.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add struct 'vicodec_dev_instance' for the fields in vicodec_dev
that have have both decoder and encoder versions.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the stateless decoder the reference buffer is null if the
frame is an I-frame (flagged with FWHT_FL_I_FRAME).
Make sure not to dereference it in that case.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename 'v4l2_fwht_default_fmt' to 'v4l2_fwht_find_nth_fmt'
and add a function 'v4l2_fwht_validate_fmt' to check if
a format info matches the parameters.
This function will also be used to validate the stateless
params when adding support for stateless codecs.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the code that validates version dependent header
values to a separate function 'validate_by_version'
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the decoder, save the inner reference frame in the same
format as the capture buffer.
The decoder writes directly to the capture buffer and then
the capture buffer is copied to the reference buffer.
This will simplify the stateless decoder.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the field 'buf' to fwht_raw_frame to indicate
the start of the raw frame buffer.
This field will be used to copy the capture buffer
to the reference buffer in the next patch.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce 'prepare_raw_frame' function that fills the values
of a raw frame struct according to the format.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function 'v4l2_m2m_buf_copy_metadata' should
be called even if decoding/encoding ends with
status VB2_BUF_STATE_ERROR, so that the metadata
is copied from the source buffer to the dest buffer.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_fwht_encode returns either an error code on
failure or the size of the compressed frame on
success. So change the var assigned to it from
'ret' to 'comp_sz_or_errcode' to clarify that.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'v4l2_m2m_ctx_release' calls request complete
so it should be called before 'v4l2_ctrl_handler_free'.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The logic of g_selection was wrong: encoders support crop,
decoders support compose, but the code allowed both.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The selection api should check only single buffer types
because multiplanar types are converted to
single in drivers/media/v4l2-core/v4l2-ioctl.c
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Checkpatch wants to use 'help' instead of '---help---':
WARNING: prefer 'help' over '---help---' for new help texts
Let's change it globally at the media subsystem, as otherwise people
would keep using the old way.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ti-vpe driver parsed the remote endpoints for properties but ignored the
local ones. Fix this by parsing the local endpoint properties instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
V4L2 fwnode matching right now still works based on device nodes, not port
nodes. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When start_streaming was called both last_src_buf and last_dst_buf
pointers were set to NULL, but this depends on whether the capture
or output queue starts streaming.
When decoding with resolution changes in between the capture queue
has to restart streaming whenever a resolution change occurs. And
that would reset last_src_buf as well, which causes a problem if
the decoder was stopped by the application. Since last_src_buf
is now NULL, the LAST flag is never set for the last capture
buffer.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some functions like enum_fmt use the buffer type as was passed
from userspace, which might cause the switch to fall into the
default case. Just drop the WARN_ON(1) to avoid kernel log pollution.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The s_stream callback was not being called for the first entity in the
stream pipeline array.
Instead of verifying the type of the node (video or subdevice) and
calling s_stream from the second entity in the pipeline, do this process
for all the entities in the pipeline for consistency.
The previous code was not a problem because the first entity is a video
device and not a subdevice, but this patch prepares vimc to allow
setting some configuration in the entity before calling s_stream.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Tested-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix line-too-long warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no need to have the frame field in the vimc_stream struct.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Tested-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The type V4L2_FRMSIZE_TYPE_CONTINUOUS expects a step of 1.
This fixes v4l2-compliance test error:
fail: v4l2-test-formats.cpp(184): invalid step_width/height for continuous framesize
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The state TASK_UNINTERRUPTIBLE should be set just before
schedule_timeout() call, so it knows the sleep mode it should enter.
There is no point in setting TASK_UNINTERRUPTIBLE at the initialization
of the thread as schedule_timeout() will set the state back to
TASK_RUNNING.
This fixes a warning in __might_sleep() call, as it's expecting the
task to be in TASK_RUNNING state just before changing the state to
a sleeping state.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The format of the sink pad should be a bayer mbus format.
This fixes a kernel NULL pointer dereference error that was caused when
the stream starts because the configured format was not found in the
pixelmap table.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang-9 makes some different inlining decisions compared to gcc, which
leads to a warning about a possible stack overflow problem when building
with CONFIG_KASAN, including when setting asan-stack=0, which avoids
most other frame overflow warnings:
drivers/media/platform/vicodec/codec-fwht.c:673:12: error: stack frame size of 2224 bytes in function 'encode_plane'
Manually adding noinline_for_stack annotations in those functions
called by encode_plane() or decode_plane() that require a significant
amount of kernel stack makes this impossible to happen with any
compiler.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ISC driver currently supports ITU-R 601 encoding which
utilizes the external hsync and vsync signals. ITU-R 656
format removes the need for these pins by embedding the
sync pulses within the data packet.
To support this feature, enable necessary register bits
when this feature is enabled via device tree.
Signed-off-by: Ken Sloat <ksloat@aampglobal.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Avoid call of dmaengine_terminate_all() between
dmaengine_prep_slave_single() and dmaengine_submit() by locking
the whole DMA submission sequence.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Start streaming was sometimes failing because of pm_runtime_get_sync()
non-0 return value. In fact return value was not an error but a
positive value (1), indicating that PM was already enabled.
Fix this by going to error path only with negative return value.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Function `sh_veu_find_fmt` returns an address that is an addition of a
base pointer `sh_veu_fmt` and an offset. The base pointer refers to a
global variable of which address cannot be NULL. Therefore, this commit
removes the NULL pointer checks on the return values of function
`sh_veu_find_fmt`.
Signed-off-by: Shaobo He <shaobo@cs.utah.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions, but omitted two occurrences that are accessed in the
mtk_v4l2_debug() macro. These only trigger compiler errors when DEBUG is
defined.
Fixes: 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem buffer helpers")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the SoC specific information for RZ/G2M(r8a774a1) SoC.
The VIN module of RZ/G2M is similar to R-Car M3-W.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2M(r8a774a1) SoC.
The CSI-2 module of RZ/G2M is similar to R-Car M3-W.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm_ioremap_resource() already prints an error message on failure, so
there is no need to repeat that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changes to v4l2-fwnode in commit [1] triggered a lockdep warning in
rcar-vin. The first attempt to solve this warning in the rcar-vin driver
was incomplete and only pushed the warning to happen at stream on time
instead of at probe time.
This change reverts the incomplete fix and properly fixes the warning by
removing the need to hold the rcar-vin specific group lock when calling
v4l2_async_notifier_parse_fwnode_endpoints_by_port(). And instead takes
it in the callback where it's really needed.
[1] commit eae2aed1ea ("media: v4l2-fwnode: Switch to
v4l2_async_notifier_add_subdev")
Fixes: 6458afc8c4 ("media: rcar-vin: remove unneeded locking in async callbacks")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the new v4l2_subdev_internal_ops release op to free the
subdev memory only when the last user closed the file handle.
Move v4l2_device_unregister_subdev() to the end of the
vimc_ent_sd_unregister() function since now the unregister_subdev()
call may free the vimc_ent_device struct which is used after the
unregister_subdev() call. So this now has to be done last.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't free vimc_cap_device immediately, instead do this
in the video_device release function which is called when the
last user closes the video device. Only then is it safe to
free the memory.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The media_device is part of a static global vimc_device struct.
The media framework expects this to be zeroed before it is
used, however, since this is a global this is not the case if
vimc is unbound and then bound again.
So call memset to ensure any left-over values are cleared.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
