We need to do errata handling every time CAL is being enabled. The code
is currently in cal_runtime_get(), which is not the correct place for
it.
Move the code to cal_runtime_resume, which is called every time CAL is
enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
i913_errata() sets a bit to 1 in PHY_REG10, but for some reason uses
CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_DISABLE for the bit value. The value of
that macro is 1, so it works, but is still wrong.
Fix this to 1.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IRQENABLE_SET registers are (usually) not meant to be read, only written
to. The current driver needlessly uses read-modify-write cycle to enable
IRQ bits.
The read-modify-write has no bad side effects here, but it's still
better to clean this up by only using write.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the CAL driver stops streaming, it will shut everything down
without waiting for the current frame to finish. This leaves the CAL DMA
in a slightly undefined state, and when CAL DMA is enabled when the
stream is started the next time, the old DMA transfer will continue.
It is not clear if the old DMA transfer continues with the exact
settings of the original transfer, or is it a mix of old and new
settings, but in any case the end result is memory corruption as the
destination memory address is no longer valid.
I could not find any way to ensure that any old DMA transfer would be
discarded, except perhaps full CAL reset. But we cannot do a full reset
when one port is getting enabled, as that would reset both ports.
This patch tries to make sure that the DMA transfer is finished properly
when the stream is being stopped. I say "tries", as, as mentioned above,
I don't see a way to force the DMA transfer to finish. I believe this
fixes the corruptions for normal cases, but if for some reason the DMA
of the final frame would stall a lot, resulting in timeout in the code
waiting for the DMA to finish, we'll again end up with unfinished DMA
transfer. However, I don't know what could cause such a timeout.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the switch to use v4l2_async_notifier_add_subdev() and
v4l2_async_notifier_cleanup(), unloading the ti_cal module would cause a
kernel oops.
This was root cause to the fact that v4l2_async_notifier_cleanup() tries
to kfree the asd pointer passed into v4l2_async_notifier_add_subdev().
In our case the asd reference was from a statically allocated struct.
So in effect v4l2_async_notifier_cleanup() was trying to free a pointer
that was not kalloc.
So here we switch to using a kzalloc struct instead of a static one.
To achieve this we re-order some of the calls to prevent asd allocation
from leaking.
Fixes: d079f94c90 ("media: platform: Switch to v4l2_async_notifier_add_subdev")
Cc: stable@vger.kernel.org
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
disable_irqs() was mistakenly disabling all interrupts when called.
This cause all port stream to stop even if only stopping one of them.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure that both enum_mbus_code() and enum_framesize() properly
populate the .which parameter member, otherwise -EINVAL is return
causing the subdev asynchronous registration handshake to fail.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When start_streaming fails after the buffers have been queued we have to
make sure all buffers are returned to user-space properly otherwise a
v4l2 level WARN is generated.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently we were using an arbitrarily small maximum resolution mostly
based on available sensor capabilities. However the hardware DMA limits
are much higher than the statically define maximum resolution we were
using.
There we rework the boundary check code to handle the maximum width and
height based on the maximum line width in bytes and re-calculating the
pixel width based on the given pixel format.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Because V4L2 still uses a specific way to manage power state of devices
that predates runtime PM, bridge driver should power on and off sub
device explicitly.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the needed control module register bit layout to support the AM654
family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the needed control module register bit layout to support
the DRA76x family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current CSI2 DPHY initialization sequence although
functional does not match with the documented sequence
in the Technical Reference Manual.
This may affect capture re-startability in stop/start
situations.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pixel processing unit was hard coded to only handle 8 bits per pixel
from input to output.
We now add handling for 10, 12 and 16 bits per pixel at the source and
setting the in-memory size (i.e. container size) to 16 bits for these 3
cases.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current method to calculate the ddr clk period is wrong.
Therefore the ths_term calculation is incorrect.
Also it was wrongly assumed that the ths_settle parameter
was based on the control clock instead of the pixel clock.
Since the DPHY can tolerate quite a bit a of variation,
capture was still mostly working with the 2 tested modes
when the pixel clock was close to the control clock
(i.e. 96 Mhz). But it would quickly stops working when
using different modes or when customers used different
sensors altogether.
Calculating the DDRClk period needs to take into account
the pixel bit width and the number of active data lanes.
Based on the latest technical reference manual these
parameters should now be calculated as follows:
THS_TERM: Programmed value = floor(20 ns/DDRClk period)
THS_SETTLE: Programmed value = floor(105 ns/DDRClk period) + 4
Also originally 'depth' was used to represent the number of
bits a pixel would use once stored in memory (i.e. the
container size). To accurately calculate the THS_* parameters
we need to use the actual number of bits per pixels coming
in from the sensor. So we are renaming 'depth' to 'bpp' (bits
per pixels) and update the format table to show the actual
number of bits per pixel being received.
The "container" size will be derived from the "bpp" value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Apply Errata i913 every time the functional clock is enabled.
This should take care of suspend/resume case as well.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When setting DMA for video capture from CSI channel, if the DMA size
is not given, it ends up writing as much data as sent by the camera.
This may lead to overwriting the buffers causing memory corruption.
Observed green lines on the default framebuffer.
Restrict the DMA to maximum height as specified in the S_FMT ioctl.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allow CAL to be able to export DMA buffer.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
First this patch adds a method to access the CTRL_CORE_CAMERRX_CONTROL
register to use the syscon mechanism. For backward compatibility we also
handle using the existing camerrx_control "reg" entry if a syscon node
is not found.
In addition the register bit layout for the CTRL_CORE_CAMERRX_CONTROL
changes depending on the device. In order to support this we need to use
a register access scheme based on data configuration instead of using
static macro.
In this case we make use of the regmap facility and create data set
based on the various device and phy available.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The call to of_get_parent returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/ti-vpe/cal.c:1621:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1607, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ti-vpe driver parsed the remote endpoints for properties but ignored the
local ones. Fix this by parsing the local endpoint properties instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media
bus enum.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Switch all media platform drivers to call v4l2_async_notifier_add_subdev()
to add asd's to a notifier, in place of referencing the notifier->subdevs[]
array. These drivers also must now call v4l2_async_notifier_init() before
adding asd's to their notifiers.
There may still be cases where a platform driver maintains a list of
asd's that is a duplicate of the notifier asd_list, in which case its
possible the platform driver list can be removed, and can reference the
notifier asd_list instead. One example of where a duplicate list has
been removed in this patch is xilinx-vipp.c. If there are such cases
remaining, those drivers should be optimized to remove the duplicate
platform driver asd lists.
None of the changes to the platform drivers in this patch have been
tested. Verify that the async subdevices needed by the platform are
bound at load time, and that the driver unloads and reloads correctly
with no memory leaking of asd objects.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
of_node_put has taken the null pinter check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Cc: Benoit Parrot <bparrot@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2_ASYNC_MATCH_FWNODE match criteria requires just one
struct to be filled (struct fwnode_handle). The V4L2_ASYNC_MATCH_DEVNAME
match criteria requires just a device name.
So, it doesn't make sense to enclose those into structs,
as the criteria can go directly into the union.
That makes easier to document it, as we don't need to document
weird senseless structs.
At drivers, this makes even clearer about the match criteria.
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Hyun Kwon <hyun.kwon@xilinx.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The async subdev notifier .bound(), .unbind() and .complete() operations
are function pointers stored directly in the v4l2_async_subdev
structure. As the structure isn't immutable, this creates a potential
security risk as the function pointers are mutable.
To fix this, move the function pointers to a new
v4l2_async_subdev_operations structure that can be made const in
drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now, we can use of_graph_get_remote_endpoint(). Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch users of the v4l2_of_ APIs to the more generic v4l2_fwnode_ APIs.
Async OF matching is replaced by fwnode matching and OF matching support
is removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Benoit Parrot <bparrot@ti.com> # i2c/ov2569.c, am437x/am437x-vpfe.c and ti-vpe/cal.c
Tested-by: Hans Verkuil <hans.verkuil@cisco.com> # Atmel sama5d3 board + ov2640 sensor
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
[hans.verkuil@cisco.com: dropped soc_camera/rcar_vin.c patch because that driver will be removed]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stop using alloc_ctx and just fill in the device pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported ctx->sensor is being dereferenced before being checked
in cal_get_external_info(). That being the case it was also checked
twice in multiple other location where v4l2_subdev_call is already
checking it so no need to explicitly check it again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported, the current cal_enum_frameintervals() is confusing
and does not have the intended behavior.
Fix this by re-implementing to properly propagate the enum_frame_interval
request to the subdevice.
[mchehab@osg.samsung.com: remove a now bogus "ret = 0" statement]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix the following sparse warnings:
ti-vpe/cal.c:387:26: warning: incorrect type in return expression (different address spaces)
ti-vpe/cal.c:459:26: warning: incorrect type in return expression (different address spaces)
ti-vpe/cal.c:503:27: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:509:47: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:518:47: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:526:31: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:1807:24: warning: Using plain integer as NULL pointer
ti-vpe/cal.c:1844:16: warning: Using plain integer as NULL pointer
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Camera Adaptation Layer (CAL) is a block which consists of a dual
port CSI2/MIPI camera capture engine.
Port #0 can handle CSI2 camera connected to up to 4 data lanes.
Port #1 can handle CSI2 camera connected to up to 2 data lanes.
The driver implements the required API/ioctls to be V4L2 compliant.
Driver supports the following:
- V4L2 API using DMABUF/MMAP buffer access based on videobuf2 api
- Asynchronous sensor sub device registration
- DT support
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
