This is only needed for drivers that do not use vb2_fop_release().
Note that vb2_queue_release() is *not* the counterpart of vb2_queue_init()
as some drivers here seem to think.
Also use vb2_video_unregister_device() to automatically stop streaming
at unregister time for those drivers that set vdev->queue.
Note that sun4i-csi didn't unregister the video device at all. That's
now fixed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For no obvious reason VB2_DMABUF was not enabled. Add this.
Also both read and write file ops were set, but this was not enabled
in the vb2 io_modes or in the device_caps capabilities. Drop this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Allwinner camera sensor interface has a different definition of
[HV]sync. While the timing diagram uses the names HSYNC and VSYNC,
the note following the diagram and register names use HREF and VREF.
Combined they imply the hardware uses either [HV]REF or inverted
[HV]SYNC. There are also registers to set horizontal skip lengths
in pixels and vertical skip lengths in lines, also known as back
porches.
Fix the polarity handling by using the opposite polarity flag for
the checks. Also rename `[hv]sync_pol` to `[hv]ref_pol` to better
match the hardware register description.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CLK_POL field specifies whether data is sampled on the falling or
rising edge of PCLK, not whether the data lines are active high or low.
Evidence of this can be found in the timing diagram labeled "horizontal
size setting and pixel clock timing".
Fix the setting by checking the correct flag, V4L2_MBUS_PCLK_SAMPLE_RISING.
While at it, reorder the three polarity flag checks so HSYNC and VSYNC
are grouped together.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The older CSI drivers have camera capture interface different from the one
in the newer ones.
This IP is pretty simple. Some variants (one controller out of two
instances on some SoCs) have an ISP embedded, but there's no code that make
use of it, so we ignored that part for now.
[Sakari Ailus: Wrapped a few long lines, set mbus code using a macro.]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
