Authenticate and enable port encryption only once for
an active HDCP 2.2 session, once port is authenticated
and encrypted enable encryption for each stream that
requires encryption on this port.
Similarly disable the stream encryption for each encrypted
stream, once all encrypted stream encryption is disabled,
disable the port HDCP encryption and deauthenticate the port.
v2:
- Add connector details in drm_err. [Ram]
- 's/port_auth/hdcp_auth_status'. [Ram]
- Added a debug print for stream enc.
v3:
- uniformity for connector detail in DMESG. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-19-anshuman.gupta@intel.com
Add support for HDCP 2.2 DP MST shim callback.
This adds existing DP HDCP shim callback for Link Authentication
and Encryption and HDCP 2.2 stream encryption
callback.
v2:
- Added a WARN_ON() instead of drm_err. [Uma]
- Cosmetic changes. [Uma]
v3:
- 's/port_data/hdcp_port_data' [Ram]
- skip redundant link check. [Ram]
v4:
- use pipe instead of port to access HDCP2_STREAM_STATUS
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-18-anshuman.gupta@intel.com
This requires for HDCP 2.2 MST check link.
As for DP/HDMI shims check_2_2_link retrieves the connector
from dig_port, this is not sufficient or DP MST connector,
there can be multiple DP MST topology connector associated
with same dig_port.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-16-anshuman.gupta@intel.com
Add support for multiple mst stream in hdcp port data
which will be used by RepeaterAuthStreamManage msg and
HDCP 2.2 security f/w for m' validation.
Security f/w doesn't have any provision to mark the stream_type
for each stream separately, it just take single input of
stream_type while authenticating the port and applies the
same stream_type to all streams. So driver mark each stream_type
with common highest supported content type for all streams
in DP MST Topology.
Security f/w supports RepeaterAuthStreamManage msg and m'
validation only once during port authentication and encryption.
Though it is not compulsory, security fw should support dynamic
update of content_type and should support RepeaterAuthStreamManage
msg and m' validation whenever required.
v2:
- Init the hdcp port data k for HDMI/DP SST stream.
v3:
- Cosmetic changes. [Uma]
v4:
- 's/port_auth/hdcp_port_auth'. [Ram]
- Commit log improvement.
v5:
- Comment and commit log improvement. [Ram]
v6:
- Check first connector connected status before intel_encoder_is_mst
to avoid any NULL pointer dereference.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Juston Li <juston.li@intel.com>
Acked-by: Juston Li <juston.li@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-15-anshuman.gupta@intel.com
hdcp_port_data is specific to a port on which HDCP
encryption is getting enabled, so encapsulate it to
intel_digital_port.
This will be required to enable HDCP 2.2 stream encryption.
v2:
- 's/port_data/hdcp_port_data'. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-12-anshuman.gupta@intel.com
Pass dig_port as an argument to intel_hdcp_init()
and intel_hdcp2_init().
This will be required for HDCP 2.2 stream encryption.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-11-anshuman.gupta@intel.com
Enable HDCP 1.4 DP MST stream encryption.
Enable stream encryption once encryption is enabled on
the DP transport driving the link for each stream which
has requested encryption.
Disable stream encryption for each stream that no longer
requires encryption before disabling HDCP encryption on
the link.
v2:
- Added debug print for stream encryption.
- Disable the hdcp on port after disabling last stream
encryption.
v3:
- Cosmetic change, removed the value less comment. [Uma]
v4:
- Split the Gen12 HDCP enablement patch. [Ram]
- Add connector details in drm_err.
v5:
- uniformity for connector detail in DMESG. [Ram]
- comments improvement. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-9-anshuman.gupta@intel.com
Both HDCP_{1.x,2.x} requires to select/deselect Multistream HDCP bit
in TRANS_DDI_FUNC_CTL in order to enable/disable stream HDCP
encryption over DP MST Transport Link.
HDCP 1.4 stream encryption requires to validate the stream encryption
status in HDCP_STATUS_{TRANSCODER,PORT} register driving that link
in order to enable/disable the stream encryption.
Both of above requirement are same for all Gen with respect to
B.Spec Documentation.
v2:
- Cosmetic changes function name, error msg print and
stream typo fixes. [Uma]
v3:
- uniformity for connector detail in DMESG. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-8-anshuman.gupta@intel.com
DP MST stream encryption status requires time of a link frame
in order to change its status, but as there were some HDCP
encryption timeout observed earlier, it is safer to use
ENCRYPT_STATUS_CHANGE_TIMEOUT_MS timeout for stream status too,
it requires to move the macro to a header.
It will be used by both HDCP{1.x,2.x} stream status timeout.
Related: 'commit 7e90e8d0c0 ("drm/i915: Increase timeout for Encrypt
status change")'
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-7-anshuman.gupta@intel.com
Gen12 has H/W delta with respect to HDCP{1.x,2.x} display engine
instances lies in Transcoder instead of DDI as in Gen11.
This requires hdcp driver to use mst_master_transcoder for link
authentication and stream transcoder for stream encryption
separately.
This will be used for both HDCP 1.4 and HDCP 2.2 over DP MST
on Gen12.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-6-anshuman.gupta@intel.com
There can be situation when DP MST connector is created without
mst modeset being done, in those cases connector->encoder will be
NULL. MST connector->encoder initializes after modeset.
Don't enable HDCP in such cases to prevent any crash.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Juston Li <juston.li@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-5-anshuman.gupta@intel.com
Handle CP_IRQ in DEVICE_SERVICE_IRQ_VECTOR_ESI0
It requires to call intel_hdcp_handle_cp_irq() in case
of CP_IRQ is triggered by a sink in DP-MST topology.
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-4-anshuman.gupta@intel.com
Get DRM connector reference count while scheduling a prop work
to avoid any possible destroy of DRM connector when it is in
DRM_CONNECTOR_REGISTERED state.
Fixes: a6597faa2d ("drm/i915: Protect workers against disappearing connectors")
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-3-anshuman.gupta@intel.com
When crtc state need_modeset is true it is not necessary
it is going to be a real modeset, it can turns to be a
fastset instead of modeset.
This turns content protection property to be DESIRED and hdcp
update_pipe left with property to be in DESIRED state but
actual hdcp->value was ENABLED.
This issue is caught with DP MST setup, where we have multiple
connector in same DP_MST topology. When disabling HDCP on one of
DP MST connector leads to set the crtc state need_modeset to true
for all other crtc driving the other DP-MST topology connectors.
This turns up other DP MST connectors CP property to be DESIRED
despite the actual hdcp->value is ENABLED.
Above scenario fails the DP MST HDCP IGT test, disabling HDCP on
one MST stream should not cause to disable HDCP on another MST
stream on same DP MST topology.
v2:
- Fixed connector->base.registration_state == DRM_CONNECTOR_REGISTERED
WARN_ON.
v3:
- Commit log improvement. [Uma]
- Added a comment before scheduling prop_work. [Uma]
Fixes: 33f9a623bf ("drm/i915/hdcp: Update CP as per the kernel internal state")
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-2-anshuman.gupta@intel.com
Device local-memory should be thought of as part the GT, which means it
should also sit under gt/.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112164300.356524-1-matthew.auld@intel.com
During igt_reset_nop_engine, it was observed that an unexpected failed
engine reset lead to us busywaiting on the stop-ring semaphore (set
during the reset preparations) on the first request afterwards. There was
no explicit MI_ARB_CHECK in this sequence as the presumption was that
the failed MI_SEMAPHORE_WAIT would itself act as an arbitration point.
It did not in this circumstance, so force it.
This patch is based on the assumption that the MI_SEMAPHORE_WAIT failure
to arbitrate is a rare Tigerlake bug, similar to the lite-restore vs
semaphore issues previously seen in the CS. The explicit MI_ARB_CHECK
should always ensure that there is at least one arbitration point in the
request before the MI_SEMAPHORE_WAIT to trigger the IDLE->ACTIVE event.
Upon processing that event, we will clear the stop-ring flag and release
the semaphore from its busywait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112100759.32698-2-chris@chris-wilson.co.uk
On the off chance that we need to arbitrate before launching the
payload, perform the check after we signal the request is ready to
start. Assuming instantaneous processing of the CS event, the request
will then be treated as having started when we make the decisions as to
how to process that CS event.
v2: More commentary about the users of i915_request_started() as a
reminder about why we are marking the initial breadcrumb.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112100759.32698-1-chris@chris-wilson.co.uk
A new fi-cml-dallium CI machine has 8G and apparently plenty free, yet
fails some selftests with ENOMEM. The failures all seem to be from
huge_gem_object which does not try very hard to allocate memory,
skipping reclaim entirely. Let's try a bit harder and direct reclaim
before failing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112020013.19464-1-chris@chris-wilson.co.uk
The clear-residuals mitigation is a relatively heavy hammer and under some
circumstances the user may wish to forgo the context isolation in order
to meet some performance requirement. Introduce a generic module
parameter to allow selectively enabling/disabling different mitigations.
To disable just the clear-residuals mitigation (on Ivybridge, Baytrail,
or Haswell) use the module parameter: i915.mitigations=auto,!residuals
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1858
Fixes: 47f8253d2b ("drm/i915/gen7: Clear all EU/L3 residual contexts")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org # v5.7
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111225220.3483-3-chris@chris-wilson.co.uk
The mitigation is required for all gen7 platforms, now that it does not
cause GPU hangs, restore it for Ivybridge and Baytrail.
Fixes: 47f8253d2b ("drm/i915/gen7: Clear all EU/L3 residual contexts")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Cc: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Reviewed-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111225220.3483-2-chris@chris-wilson.co.uk
MEDIA_STATE_VFE only accepts the 'maximum number of threads' in the
range [0, n-1] where n is #EU * (#threads/EU) with the number of threads
based on plaform and the number of EU based on the number of slices and
subslices. This is a fixed number per platform/gt, so appropriately
limit the number of threads we spawn to match the device.
v2: Oversaturate the system with tasks to force execution on every HW
thread; if the thread idles it is returned to the pool and may be reused
again before an unused thread.
v3: Fix more state commands, which was causing Baytrail to barf.
v4: STATE_CACHE_INVALIDATE requires a stall on Ivybridge
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2024
Fixes: 47f8253d2b ("drm/i915/gen7: Clear all EU/L3 residual contexts")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Cc: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Randy Wright <rwright@hpe.com>
Cc: stable@vger.kernel.org # v5.7+
Reviewed-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111225220.3483-1-chris@chris-wilson.co.uk
DG1's vswing tables are the same for eDP and HDMI but have slight
differences from ICL/TGL for DP.
v2:
- Use a "_hbr2_hbr3" suffix on the table name to make it more clear
that the same table is used for both HBR2 and HBR3 link rates.
(Swathi)
Bspec: 49291
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108222528.1954514-1-matthew.d.roper@intel.com
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Braswell's pdp workaround is full of dragons, that may be being angered
when they are interrupted. Let's not take that risk and disable
arbitration during the update.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111105735.21515-1-chris@chris-wilson.co.uk
Some new eDP panels don't like to operate at the max parameters, and
instead we need to go for an optimal confiugration. That unfortunately
doesn't work with older eDP panels which are generally only guaranteed
to work at the max parameters.
To solve these two conflicting requirements let's start with the optimal
setup, and if that fails we start again with the max parameters. The
downside is probably an extra modeset when we switch strategies but
I don't see a good way to avoid that.
For a bit of history we first tried to go for the fast+narrow in
commit 7769db5883 ("drm/i915/dp: optimize eDP 1.4+ link config
fast and narrow"). but that had to be reverted due to regression
on older panels in commit f11cb1c19a ("drm/i915/dp: revert back
to max link rate and lane count on eDP"). So now we try to get
the best of both worlds by using both strategies.
v2: Deal with output_bpp and uapi vs. hw state split
Reword some comments
v3: Rebase
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Albert Astals Cid <aacid@kde.org> # v5.0 backport
Cc: Emanuele Panigati <ilpanich@gmail.com> # v5.0 backport
Cc: Matteo Iervasi <matteoiervasi@gmail.com> # v5.0 backport
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=105267
References: https://bugs.freedesktop.org/show_bug.cgi?id=109959
References: https://gitlab.freedesktop.org/drm/intel/issues/272
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107182026.24848-1-ville.syrjala@linux.intel.com
Eliminate checkpatch warnings from intel_cursor.c:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Possible repeated word: 'by'
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110175624.3524-2-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
There was some misinterpretation of specification, when DDIX_USED is
set, the next bit means 0 for DP and 1 for HDMI.
Anyways this misinterpretation is not causing any issues, this change
is just to comply with specification.
Also as for us it do not matters if it is HDMI or DP, not checking the
port type that HTI is using.
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108134802.21280-1-jose.souza@intel.com
These error paths return success instead of negative error codes as
intended.
Fixes: c92724de6d ("drm/i915/selftests: Try to detect rollback during batchbuffer preemption")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/X/xMdcewtft7+QFM@mwanda
The pch_get_backlight(), lpt_get_backlight(), and lpt_set_backlight()
functions operate directly on the hardware registers. If inverting the
value is needed, using intel_panel_compute_brightness(), it should only
be done in the interface between hardware registers and
panel->backlight.level.
The CPU mode takeover code added in commit 5b1ec9ac7a
("drm/i915/backlight: Fix backlight takeover on LPT, v3.") reads the
hardware register and converts to panel->backlight.level correctly,
however the value written back should remain in the hardware register
"domain".
This hasn't been an issue, because GM45 machines are the only known
users of i915.invert_brightness and the brightness invert quirk, and
without one of them no conversion is made. It's likely nobody's ever hit
the problem.
Fixes: 5b1ec9ac7a ("drm/i915/backlight: Fix backlight takeover on LPT, v3.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v5.1+
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108152841.6944-1-jani.nikula@intel.com
When wedging the device, we cancel all outstanding requests and mark
them as EIO. Rather than duplicate the small function to do so between
each submission backend, export one.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210109163455.28466-3-chris@chris-wilson.co.uk
drivers/gpu/drm/i915//gt/intel_workarounds.c:1394:20: error: function 'is_nonpriv_flags_valid' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static inline bool is_nonpriv_flags_valid(u32 flags)
This is only used by debug build, so mark it as maybe-unused to keep the
compiler from complaining.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210109163455.28466-2-chris@chris-wilson.co.uk
Inject a fault into lrc_init_wa_ctx() to ensure that we can tolerate a
failure to construct the workarounds.
v2: Avoid mentioning an error for fault-injection, other CI will
complain about the dmesg spam.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210109114453.27798-1-chris@chris-wilson.co.uk
If a request is submitted and known to require no preemption, disable
arbitration around the batch which prevents the HW from handling a
preemption request during the payload.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-7-chris@chris-wilson.co.uk
The reason why we did not enable preemption on Broadwater was due to
missing GPGPU workarounds. Since this only applies to rcs0, only
restrict rcs0 (and our global capabilities).
While this does not affect exposing a preemption capability to
userspace, it does affect our internal decisions on whether to use
timeslicing and semaphores between individual engines.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-6-chris@chris-wilson.co.uk
We use the completion of the last active breadcrumb to retire the
requests along a timeline. This is purely opportunistic as nothing
guarantees that any particular timeline is terminated by a breadcrumb;
except for parking the engine where we explicitly add a breadcrumb so
that we park quickly and do an explicit retire upon signaling to reduce
the latency dramatically (avoiding a retire worker roundtrip).
With scheduling, we anticipate retiring completed timelines as a matter
of course. Performing the same action from inside the breadcrumbs is
intended to provide similar functionality for legacy ringbuffer
submission.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-5-chris@chris-wilson.co.uk
Before we mark the virtual engine as no longer inflight, flush any
ongoing signaling that may be using the ce->signal_link along the
previous breadcrumbs. On switch to a new physical engine, that link will
be inserted into the new set of breadcrumbs, causing confusion to an
ongoing iterator.
This patch undoes a last minute mistake introduced into commit
bab0557c8d ("drm/i915/gt: Remove virtual breadcrumb before transfer"),
whereby instead of unconditionally applying the flush, it was only
applied if the request itself was going to be reused.
v2: Generalise and cancel all remaining ce->signals
Fixes: bab0557c8d ("drm/i915/gt: Remove virtual breadcrumb before transfer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-4-chris@chris-wilson.co.uk
If any of the perf tests run into 0 time, not only are we liable to
divide by zero, but the result would be highly questionable.
Nevertheless, let's not have a div-by-zero error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-2-chris@chris-wilson.co.uk
On error we unpin and free the wa_ctx.vma, but do not clear any of the
derived flags. During lrc_init, we look at the flags and attempt to
dereference the wa_ctx.vma if they are set. To protect the error path
where we try to limp along without the wa_ctx, make sure we clear those
flags!
Reported-by: Matt Roper <matthew.d.roper@intel.com>
Fixes: 604a8f6f1e ("drm/i915/lrc: Only enable per-context and per-bb buffers if set")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-1-chris@chris-wilson.co.uk
As with the regular suspend paths, also disable the wakeref assertions
as we disable the driver during shutdown.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2899
Fixes: fe0f1e3bfd ("drm/i915: Shut down displays gracefully on reboot")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104203905.19248-1-chris@chris-wilson.co.uk
We need a power_domain wakeref in pps_{lock,unlock} to prevent
a race while resetting pps state in intel_power_sequencer_reset().
intel_power_sequencer_reset() need a pps_mutex to access pps_pipe
but it can't grab pps_mutex due to deadlock with power_well
functions are called while holding pps_mutex.
intel_power_sequencer_reset() is called by power_well function
associated with legacy platforms like vlv and chv therefore re-use
the POWER_DOMAIN_DISPLAY_CORE power domain, which only used
by vlv and chv display power domain.
This will avoids the unnecessary noise of unrelated power wells
in pps_{lock,unlock}.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107112500.16216-1-anshuman.gupta@intel.com
In the next^W future patch, we remove the strict priority system and
continuously re-evaluate the relative priority of tasks. As such we need
to enable the timeslice whenever there is more than one context in the
pipeline. This simplifies the decision and removes some of the tweaks to
suppress timeslicing, allowing us to lift the timeslice enabling to a
common spot at the end of running the submission tasklet.
One consequence of the suppression is that it was reducing fairness
between virtual engines on an over saturated system; undermining the
principle for timeslicing.
v2: Commentary
v3: Commentary for the right cancel_timer()
v4: Add tracing for why we need a timeslice
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2802
Testcase: igt/gem_exec_balancer/fairslice
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107132322.28373-1-chris@chris-wilson.co.uk
Commit 25b4620ee8 ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
added an intel_dsi_msleep() helper which skips sleeping if the
MIPI-sequences have a version of 3 or newer and the panel is in vid-mode;
and it moved a bunch of msleep-s over to this new helper.
This was based on my reading of the big comment around line 730 which
starts with "Panel enable/disable sequences from the VBT spec.",
where the "v3 video mode seq" column does not have any wait t# entries.
Given that this code has been used on a lot of different devices without
issues until now, it seems that my interpretation of the spec here is
mostly correct.
But now I have encountered one device, an Acer Aspire Switch 10 E
SW3-016, where the panel will not light up unless we do actually honor the
panel_on_delay after exexuting the MIPI_SEQ_PANEL_ON sequence.
What seems to set this model apart is that it is lacking a
MIPI_SEQ_DEASSERT_RESET sequence, which is where the power-on
delay usually happens.
Fix the panel not lighting up on this model by using an unconditional
msleep(panel_on_delay) instead of intel_dsi_msleep() when there is
no MIPI_SEQ_DEASSERT_RESET sequence.
Fixes: 25b4620ee8 ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201118124058.26021-1-hdegoede@redhat.com
Add support for DP-HDMI2.1 PCON
From the series cover letter:
This patch series attempts to add support for a DP-HDMI2.1 Protocol
Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
E5 to DisplayPort_v2.0:
https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
The details are mentioned in:
VESA DP-to-HDMI PCON Specification Standalone Document
https://groups.vesa.org/wg/DP/document/15651
This series starts with adding support for FRL (Fixed Rate Link)
Training between the PCON and HDMI2.1 sink.
As per HDMI2.1 specification, a new data-channel or lane is added in
FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
lanes).
With these patches, the HDMI2.1 PCON can be configured to achieve FRL
training based on the maximum FRL rate supported by the panel, source
and the PCON.
The approach is to add the support for FRL training between PCON and
HDMI2.1 sink and gradually add other blocks for supporting higher
resolutions and other HDMI2.1 features, that can be supported by pcon
for the sources that do not natively support HDMI2.1.
This is done before the DP Link training between the source and PCON
is started. In case of FRL training is not achieved, the PCON will
work in the regular TMDS mode, without HDMI2.1 feature support.
Any interruption in FRL training between the PCON and HDMI2.1 sink is
notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
registers are read and FRL training is re-attempted.
Currently, we have tested the FRL training and are able to enable 4K
display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
panel.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lfdpndkt.fsf@intel.com
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
-----BEGIN PGP SIGNATURE-----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=orEC
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-12-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.12:
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/78381a4f-45fd-aed4-174a-94ba051edd37@linux.intel.com
The bspec has been updated with new vswing programming for RKL DP. No
data is provided for HDMI or eDP, so for now we'll continue to assume
that those are the same as TGL.
Bspec: 49291
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218040535.45492-1-matthew.d.roper@intel.com
Reviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
AFter detecting a register mismatch between the protocontext and the
image generated by HW, immediately break out of the double loop.
Otherwise we end up with a second confusing error message.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210106123939.18435-1-chris@chris-wilson.co.uk
After boot into kernel. Driver configured ddc pin mapping based on
predefined table in parse_ddi_port(). Now driver configure rkl
ddc pin mapping depends on icp_ddc_pin_map[]. Then this table will
give incorrect gmbus port number to cause HDMI can't work.
Refer to commit cd0a89527d ("drm/i915/rkl: Add DDC pin mapping").
Create two ddc pin table for rkl TGP and CMP pch. Then HDMI can
works properly on rkl.
v2: update patch based on latest dinq branch.
v3: update ddc table for RKL+TGP sku.
RKL+CNP sku will load cnp_ddc_pin_map[] setting.
v4: modify the if/else judgment to avoid nesting.
v5: fix typo in v4.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2577
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117142629.28729-1-shawn.c.lee@intel.com
It programs Plane's calculated x, y, offset to Plane SF register.
It does the calculation of x and y offsets using
skl_calc_main_surface_offset().
v3: Update commit message
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-4-jose.souza@intel.com
The calculation the offsets of the main surface will be needed by PSR2
selective fetch code so here splitting and exporting it.
No functional changes were done here.
v3: Rebased
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-3-jose.souza@intel.com
Now using plane damage clips property to calcualte the damaged area.
Selective fetch only supports one region to be fetched so software
needs to calculate a bounding box around all damage clips.
Now that we are not complete fetching each plane, there is another
loop needed as all the plane areas that intersect with the pipe
damaged area needs to be fetched from memory so the complete blending
of all planes can happen.
v2:
- do not shifting new_plane_state->uapi.dst only src is in 16.16 format
v4:
- setting plane selective fetch area using the whole pipe damage area
- mark the whole plane area damaged if plane visibility or alpha
changed
v5:
- taking in consideration src.y1 in the damage coordinates
- adding to the pipe damaged area planes that were visible but are
invisible in the new state
v6:
- consider old state plane coordinates when visibility changes or it
moved to calculate damaged area
- remove from damaged area the portion not in src clip
v7:
- intersec every damage clip with src to minimize damaged area
v8:
- adjust pipe_damaged area to 4 lines grouping
- adjust calculation now that is understood that uapi.src is the
framebuffer coordinates that plane will start to fetch from
v9:
- Only add plane dst or src to damaged_area if visible
- Early skip plane damage calculation if it was not visible in old and
new state
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-2-jose.souza@intel.com
In generating the reference LRC, we want a page-aligned address for
simplicity in computing the offsets within. This then shares the
computation for the HW LRC which is mapped and so page aligned, making
the comparison straightforward. It seems that kmalloc(4k) is not always
returning from a 4k-aligned slab cache (which would give us a page aligned
address) so force alignment by explicitly allocating a page.
Reported-by: "Gote, Nitin R" <nitin.r.gote@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Gote, Nitin R" <nitin.r.gote@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923114156.17749-1-chris@chris-wilson.co.uk
Older platforms use rawclk to derive the CS clock. rawclk is being
determined during intel_device_info_init(), and so that needs to be
pushed slightly earlier.
Fixes: f170523a7b ("drm/i915/gt: Consolidate the CS timestamp clocks")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104115145.24460-2-chris@chris-wilson.co.uk
In the near future, upstream will introduce a SZ_8G macro that is
slightly different to our own. Employ a temporary ifndef to avoid
compilation failure until we have backmerged.
References: 8b0fac44bd ("sizes.h: add SZ_8G/SZ_16G/SZ_32G macros")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104171511.32684-1-chris@chris-wilson.co.uk
Randconfig builds on 32-bit machines show lots of warnings for
the i915 driver for passing a 32-bit value into __const_hweight64():
drivers/gpu/drm/i915/gem/i915_gem_execbuffer.c:2584:9: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
return hweight64(VDBOX_MASK(&i915->gt));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/asm-generic/bitops/const_hweight.h:29:49: note: expanded from macro 'hweight64'
#define hweight64(w) (__builtin_constant_p(w) ? __const_hweight64(w) : __arch_hweight64(w))
Change it to hweight_long() to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210103135158.3591442-1-arnd@kernel.org
This allows us to remove pin_map from state allocation, which saves
us a few retry loops. We won't need this until first pin, anyway.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201231170405.22843-1-chris@chris-wilson.co.uk
Let's modify the "workaround lost" error message slightly to make it
more clear what the various numbers represent. Also, the 'expected'
value needs to be &'d with wa->read so that it doesn't include the mask
bits for masked registers (those bits are write-only in the hardware and
will usually always read out as 0's).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201231191103.854519-1-matthew.d.roper@intel.com
Since we use a flag within i915_request.flags to indicate when we have
boosted the request (so that we only apply the boost) once, this can be
used as the serialisation with i915_request_retire() to avoid having to
explicitly take the i915_request.lock which is more heavily contended.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201231093149.19086-1-chris@chris-wilson.co.uk
We only need to evaluate the current status of the context when it is
scheduled in, we will force a reschedule when the context is closed
propagating the change to inflight contexts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201231093946.11649-1-chris@chris-wilson.co.uk
Since we process schedule-in of a context after submitting the request,
if we decide to reset the context at that time, we also have to cancel
the requets we have marked for submission.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201230220028.17089-1-chris@chris-wilson.co.uk
Since multiple connectors may run intel_dp_aux_xfer conncurrently, a
single global pm_qos does not suffice. (One connector may disable the
dma-latency boost prematurely while the second is still depending on
it.) Instead of a single global pm_qos, track the pm_qos request for
each intel_dp.
v2: Move the pm_qos setup/teardown to intel_dp_aux_init/fini
Fixes: 9ee32fea5f ("drm/i915: irq-drive the dp aux communication")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201230202309.23982-1-chris@chris-wilson.co.uk
Declare that, under extreme circumstances, the shrinker may need to wait
upon a request, in which case reset must not itself deadlock in order to
ensure forward progress of the driver. That is since the shrinker may
depend upon a reset, any reset cannot touch the shrinker.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201229141626.4773-1-chris@chris-wilson.co.uk
accesses, inefficient and disfunctional code. The goal is to remove the
export of irq_to_desc() to prevent these things from creeping up again.
-----BEGIN PGP SIGNATURE-----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=BXv+
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is the second attempt after the first one failed miserably and
got zapped to unblock the rest of the interrupt related patches.
A treewide cleanup of interrupt descriptor (ab)use with all sorts of
racy accesses, inefficient and disfunctional code. The goal is to
remove the export of irq_to_desc() to prevent these things from
creeping up again"
* tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
genirq: Restrict export of irq_to_desc()
xen/events: Implement irq distribution
xen/events: Reduce irq_info:: Spurious_cnt storage size
xen/events: Only force affinity mask for percpu interrupts
xen/events: Use immediate affinity setting
xen/events: Remove disfunct affinity spreading
xen/events: Remove unused bind_evtchn_to_irq_lateeoi()
net/mlx5: Use effective interrupt affinity
net/mlx5: Replace irq_to_desc() abuse
net/mlx4: Use effective interrupt affinity
net/mlx4: Replace irq_to_desc() abuse
PCI: mobiveil: Use irq_data_get_irq_chip_data()
PCI: xilinx-nwl: Use irq_data_get_irq_chip_data()
NTB/msi: Use irq_has_action()
mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc
pinctrl: nomadik: Use irq_has_action()
drm/i915/pmu: Replace open coded kstat_irqs() copy
drm/i915/lpe_audio: Remove pointless irq_to_desc() usage
s390/irq: Use irq_desc_kstat_cpu() in show_msi_interrupt()
parisc/irq: Use irq_desc_kstat_cpu() in show_interrupts()
...
Pull the individual strands of creating a custom heartbeat requests into
a pair of common functions. This will reduce the number of changes we
will need to make in future.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224160213.29521-1-chris@chris-wilson.co.uk
The reloc batch is short lived but can exist in the user visible ppGTT,
and since it's backed by an internal object, which lacks page clearing,
we should take care to clear it upfront.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224151358.401345-2-matthew.auld@intel.com
Cc: stable@vger.kernel.org
The shadow batch is an internal object, which doesn't have any page
clearing, and since the batch_len can be smaller than the object, we
should take care to clear it.
Testcase: igt/gen9_exec_parse/shadow-peek
Fixes: 4f7af1948a ("drm/i915: Support ro ppgtt mapped cmdparser shadow buffers")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224151358.401345-1-matthew.auld@intel.com
Cc: stable@vger.kernel.org
Now that the tasklet completely controls scheduling of the requests, and
we postpone scheduling out the old requests, we can keep a hanging
virtual request bound to the engine on which it hung, and remove it from
te queue. On release, it will be returned to the same engine and remain
in its queue until it is scheduled; after which point it will become
eligible for transfer to a sibling. Instead, we could opt to resubmit the
request along the virtual engine on unhold, making it eligible for load
balancing immediately -- but that seems like a pointless optimisation
for a hanging context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224135544.1713-8-chris@chris-wilson.co.uk
Having recognised that we do not change the sibling until we schedule
out, we can then defer the decision to resubmit the virtual engine from
the unwind of the active queue to scheduling out of the virtual context.
This improves our resilence in virtual engine scheduling, and should
eliminate the rare cases of gem_exec_balance failing.
By keeping the unwind order intact on the local engine, we can preserve
data dependency ordering while doing a preempt-to-busy pass until we
have determined the new ELSP. This means that if we try to timeslice
between a virtual engine and a data-dependent ordinary request, the pair
will maintain their relative ordering and we will avoid the
resubmission, cancelling the timeslicing until further change.
The dilemma though is that we then may end up in a situation where the
'demotion' of the virtual request to an ordinary request in the engine
queue results in filling the ELSP[] with virtual requests instead of
spreading the load across the engines. To compensate for this, we mark
each virtual request and refuse to resubmit a virtual request in the
secondary ELSP slots, thus forcing subsequent virtual requests to be
scheduled out after timeslicing. By delaying the decision until we
schedule out, we will avoid unnecessary resubmission.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2079
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2098
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224135544.1713-7-chris@chris-wilson.co.uk
Let's only wait for the list iterator when decoupling the virtual
breadcrumb, as the signaling of all the requests may take a long time,
during which we do not want to keep the tasklet spinning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224135544.1713-6-chris@chris-wilson.co.uk
The issue with stale virtual breadcrumbs remain. Now we have the problem
that if the irq-signaler is still referencing the stale breadcrumb as we
transfer it to a new sibling, the list becomes spaghetti. This is a very
small window, but that doesn't stop it being hit infrequently. To
prevent the lists being tangled (the iterator starting on one engine's
b->signalers but walking onto another list), always decouple the virtual
breadcrumb on schedule-out and make sure that the walker has stepped out
of the lists.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224135544.1713-5-chris@chris-wilson.co.uk
Inside schedule_out, we do extra work upon idling the context, such as
updating the runtime, kicking off retires, kicking virtual engines.
However, if we are in a series of processing single requests per
contexts, we may find ourselves scheduling out the context, only to
immediately schedule it back in during dequeue. This is just extra work
that we can avoid if we keep the context marked as inflight across the
dequeue. This becomes more significant later on for minimising virtual
engine misses.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224135544.1713-4-chris@chris-wilson.co.uk
Once a virtual engine has been bound to a sibling, it will remain bound
until we finally schedule out the last active request. We can not rebind
the context to a new sibling while it is inflight as the context save
will conflict, hence we wait. As we cannot then use any other sibliing
while the context is inflight, only kick the bound sibling while it
inflight and upon scheduling out the kick the rest (so that we can swap
engines on timeslicing if the previously bound engine becomes
oversubscribed).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224135544.1713-3-chris@chris-wilson.co.uk
Rather than going back and forth between the rb_node entry and the
virtual_engine type, store the ve local and reuse it. As the
container_of conversion from rb_node to virtual_engine requires a
variable offset, performing that conversion just once shaves off a bit
of code.
v2: Keep a single virtual engine lookup, for typical use.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224135544.1713-2-chris@chris-wilson.co.uk
Rather than having special case code for opportunistically calling
process_csb() and performing a direct submit while holding the engine
spinlock for submitting the request, simply call the tasklet directly.
This allows us to retain the direct submission path, including the CS
draining to allow fast/immediate submissions, without requiring any
duplicated code paths, and most importantly greatly simplifying the
control flow by removing reentrancy. This will enable us to close a few
races in the virtual engines in the next few patches.
The trickiest part here is to ensure that paired operations (such as
schedule_in/schedule_out) remain under consistent locking domains,
e.g. when pulled outside of the engine->active.lock
v2: Use bh kicking, see commit 3c53776e29 ("Mark HI and TASKLET
softirq synchronous").
v3: Update engine-reset to be tasklet aware
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224135544.1713-1-chris@chris-wilson.co.uk
If we want to reuse a fence that is in active use by the GPU, we have to
wait an uncertain amount of time, but if we reuse an inactive fence, we
can change it right away. Loop through the list of available fences
twice, ignoring any active fences on the first pass.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201223122051.4624-1-chris@chris-wilson.co.uk
Pull the GT clock information [used to derive CS timestamps and PM
interval] under the GT so that is it local to the users. In doing so, we
consolidate the two references for the same information, of which the
runtime-info took note of a potential clock source override and scaling
factors.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201223122359.22562-2-chris@chris-wilson.co.uk
We assume that both timestamps are driven off the same clock [reported
to userspace as I915_PARAM_CS_TIMESTAMP_FREQUENCY]. Verify that this is
so by reading the timestamp registers around a busywait (on an otherwise
idle engine so there should be no preemptions).
v2: Icelake (not ehl, nor tgl) seems to be using a fixed 80ns interval
for, and only for, CTX_TIMESTAMP -- or it may be GPU frequency and the
test is always running at maximum frequency?. As far as I can tell, this
isolated change in behaviour is undocumented.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201223122359.22562-1-chris@chris-wilson.co.uk
No functional changes yet, this just adds definitions for all of the
known DPCD registers used by Intel's HDR backlight interface. Since
we'll only ever use this in i915, we just define them in
intel_dp_aux_backlight.c
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-7-lyude@redhat.com
Since we're about to add support for a second type of backlight control
interface over DP AUX (specifically, Intel's proprietary HDR backlight
controls) let's rename all of the current backlight hooks we have for
vesa to make it clear that they're specific to the VESA interface and
not Intel's.
v3:
* Rebase
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-6-lyude@redhat.com
Instead of using intel_panel->backlight.level, have the caller provide us
with the current panel backlight value. We'll need this for when we
separate PWM-related backlight callbacks from other means of backlight
control (like DPCD backlight controls), as the caller of each PWM callback
will be responsible for converting the current brightness value to it's
respective PWM level.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-4-lyude@redhat.com
Since we're going to need to add a set of lower-level PWM backlight
control hooks to be shared by normal backlight controls and HDR
backlight controls in SDR mode, let's add a prefix to the external PWM
backlight functions so that the difference between them and the high
level PWM-only backlight functions is a bit more obvious.
This introduces no functional changes.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-3-lyude@redhat.com
Since we're about to start adding support for Intel's magic HDR
backlight interface over DPCD, we need to ensure we're properly
programming this field so that Intel specific sink services are exposed.
Otherwise, 0x300-0x3ff will just read zeroes.
We also take care not to reprogram the source OUI if it already matches
what we expect. This is just to be careful so that we don't accidentally
take the panel out of any backlight control modes we found it in.
v2:
* Add careful parameter to intel_edp_init_source_oui() to avoid
re-writing the source OUI if it's already been set during driver
initialization
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-2-lyude@redhat.com
The caller determines if the failure is an error or not, so avoid
warning when we will try again and succeed. For example,
<7> [111.319321] [drm:intel_guc_fw_upload [i915]] GuC status 0x20
<3> [111.319340] i915 0000:00:02.0: [drm] *ERROR* GuC load failed: status = 0x00000020
<3> [111.319606] i915 0000:00:02.0: [drm] *ERROR* GuC load failed: status: Reset = 0, BootROM = 0x10, UKernel = 0x00, MIA = 0x00, Auth = 0x00
<7> [111.320045] [drm:__uc_init_hw [i915]] GuC fw load failed: -110; will reset and retry 2 more time(s)
<7> [111.322978] [drm:intel_guc_fw_upload [i915]] GuC status 0x8002f0ec
should not have been reported as a _test_ failure, as the GuC was
successfully loaded on the second attempt and the system remained
operational.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2797
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201214100949.11387-2-chris@chris-wilson.co.uk
If PCON has capability to convert RGB->YCbCr colorspace and also
to 444->420 downsampling then for any YUV420 only mode, we can
let the PCON do all the conversion. If the PCON supports
RGB->YCbCr conversion for all BT2020, BT709, BT601, choose
the one that is selected by userspace via connector colorspace
property, otherwise default to BT601.
v2: As suggested by Uma Shankar, considered case for colorspace
BT709 and BT2020, and default to BT601. Also appended dir
'display' in commit message.
v3: Fixed typo in condition for printing one of the error msg.
v4: As suggested by Uma Shankar:
-Fixed bug in determining the colorspace for RGB->YCbCr conversion.
-Fixed minor formatting issues
Also updated the commit message as per latest changes.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-16-ankit.k.nautiyal@intel.com
When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink
via DP HDMI2.1 PCON, the PCON can be configured to decode the
DSC1.1 compressed stream and encode to DSC1.2. It then sends the
DSC1.2 compressed stream to the HDMI2.1 sink.
This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based
on the PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder
capabilities.
v2: Addressed review comments from Uma Shankar:
-fixed the error in packing pps parameter values
-added check for pcon in the pcon related function
-appended display in commit message
v3: Only consider non-zero DSC FRL b/w for determining max FRL b/w
supported by sink.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch BRACES, LINE_SPACING, PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-15-ankit.k.nautiyal@intel.com
The DP-HDMI2.1 PCON spec provides way for a source to set PPS
parameters: slice height, slice width and bits_per_pixel, based on
the HDMI2.1 sink capabilities. The DSC encoder of the PCON will
respect these parameters, while preparing the 128 byte PPS.
This patch adds helper functions to calculate these PPS paremeters as
per the HDMI2.1 specification.
v2: Addressed review comments given by Uma Shankar:
-added documentation for functions
-fixed typos and errors
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch SUSPECT_CODE_INDENT, TYPO_SPELLING]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-14-ankit.k.nautiyal@intel.com
This patch adds support to read and store the DSC capabilities of the
HDMI2.1 PCon encoder. It also adds a new field to store these caps,
The caps are read during dfp update and can later be used to get the
PPS parameters for PCON-HDMI2.1 sink pair. Which inturn will be used
to take a call to override the existing PPS-metadata, by either
writing the entire new PPS metadata, or by writing only the
PPS override parameters.
v2: Restructured the code to read all capability DPCDs at once and store
in an array in intel_dp structure.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-13-ankit.k.nautiyal@intel.com
In this patch enables support for detecting link failures between
PCON and HDMI sink in i915 driver. HDMI link loss indication to
upstream DP source is indicated via IRQ_HPD. This is followed by
reading of HDMI link configuration status (HDMI_TX_LINK_ACTIVE_STATUS).
If the PCON → HDMI 2.1 link status is off; reinitiate frl link
training to recover. Also, report HDMI FRL link error count range for
each individual FRL active lane is indicated by
DOWNSTREAM_HDMI_ERROR_STATUS_LN registers.
v2: Checked for dpcd read and write failures and added debug message.
(Uma Shankar)
v3: Rearranged code to re-start FRL link training or fall back to
TMDS mode.
v4: Resused function to check frl which inturn restarts FRL and
fallback to TMDS mode.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-12-ankit.k.nautiyal@intel.com
This patch calls functions to check FRL training requirements
for an HDMI2.1 sink, when connected through PCON.
The call is made before the DP link training. In case FRL is not
required or failure during FRL training, the TMDS mode is selected
for the pcon.
v2: moved check_frl_training() just after FEC READY, before
starting DP link training.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-11-ankit.k.nautiyal@intel.com
This patch adds functions to start FRL training for an HDMI2.1 sink,
connected via a PCON as a DP branch device.
This patch also adds a new structure for storing frl training related
data, when FRL training is completed.
v2: As suggested by Uma Shankar:
-renamed couple of variables for better clarity
-tweaked the macros used for correct semantics for true/false
-fixed other styling issues.
v3: Completed the TODO for condition for going to FRL mode.
Modified the condition to determine the required FRL b/w
based only on the Pcon and Sink's max FRL values.
Moved the frl structure initialization to intel_dp_init_connector().
v4: Fixed typo in initialization of frl structure.
v5: Always use FRL if its possible, instead of enabling only for
higher modes as done in v3.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
[Jani: Fixed checkpatch BRACES, CONSTANT_COMPARISON.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-10-ankit.k.nautiyal@intel.com
HDMI2.1 PCON advertises Max FRL bandwidth supported by the PCON.
This patch captures this in dfp cap structure in intel_dp and uses
this to prune connector modes that cannot be supported by the PCON
and FRL bandwidth.
v2: Addressed review comments from Uma Shankar:
-tweaked the comparison of target bw and pcon frl bw to avoid roundup errors.
-minor modification of field names and comments.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-9-ankit.k.nautiyal@intel.com
When waiting for the submit, before checking the status of the request,
kick the tasklet to make sure we are processing the submission. This
speeds up submission if we are using any tasklet suppression for
secondary requests.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201222113536.3775-3-chris@chris-wilson.co.uk
Make sure that the request has been submitted to HW before we begin our
wait. This reduces our reliance on the semaphore yield interrupt driving
the preemption request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201222113536.3775-2-chris@chris-wilson.co.uk
We assume that the contents of the HWSP are lost across suspend, and so
upon resume we must restore critical values such as the timeline seqno.
Keep track of every timeline allocated that uses the HWSP as its storage
and so we can then reset all seqno values by walking that list.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201222104242.10993-1-chris@chris-wilson.co.uk
Ville suggested this as a good idea, let's move this before moving
the crtc code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: fixed i915xx_plane.h standalone build.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201221110957.18215-1-jani.nikula@intel.com
This file is a monster, let's start simple, the cursor plane code
seems pretty standalone, and splits out easily enough.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Jani: cleaned up intel_cursor.h a bit.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201221090449.8288-4-jani.nikula@intel.com
Primarily used by selftests, but also by runtime debugging of engine
w/a, is a routine to create a temporarily bound buffer for readback.
Almagamate the duplicated routines into one.
Suggested-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201219020343.22681-2-chris@chris-wilson.co.uk
Split the definition, construction and updating of the Logical Ring
Context from the execlist submission interface. The LRC is used by the
HW, irrespective of our different submission backends.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201219020343.22681-1-chris@chris-wilson.co.uk
tasklet_kill() ensures that we _yield_ the processor until a remote
tasklet is completed. However, this leads to a starvation condition as
being at the bottom of the scheduler's runqueue means that anything else
is able to run, including all hogs keeping the tasklet occupied.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201220134858.10510-1-chris@chris-wilson.co.uk
- Only enable char/agp uapi when CONFIG_DRM_LEGACY is set
Cross-subsystem Changes:
- vma_set_file helper to make vma->vm_file changing less brittle,
acked by Andrew
Core Changes:
- dma-buf heaps improvements
- pass full atomic modeset state to driver callbacks
- shmem helpers: cached bo by default
- cleanups for fbdev, fb-helpers
- better docs for drm modes and SCALING_FITLER uapi
- ttm: fix dma32 page pool regression
Driver Changes:
- multi-hop regression fixes for amdgpu, radeon, nouveau
- lots of small amdgpu hw enabling fixes (display, pm, ...)
- fixes for imx, mcde, meson, some panels, virtio, qxl, i915, all
fairly minor
- some cleanups for legacy drm/fbdev drivers
-----BEGIN PGP SIGNATURE-----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=BhU/
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-18' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Daniel Vetter:
"UAPI Changes:
- Only enable char/agp uapi when CONFIG_DRM_LEGACY is set
Cross-subsystem Changes:
- vma_set_file helper to make vma->vm_file changing less brittle,
acked by Andrew
Core Changes:
- dma-buf heaps improvements
- pass full atomic modeset state to driver callbacks
- shmem helpers: cached bo by default
- cleanups for fbdev, fb-helpers
- better docs for drm modes and SCALING_FITLER uapi
- ttm: fix dma32 page pool regression
Driver Changes:
- multi-hop regression fixes for amdgpu, radeon, nouveau
- lots of small amdgpu hw enabling fixes (display, pm, ...)
- fixes for imx, mcde, meson, some panels, virtio, qxl, i915, all
fairly minor
- some cleanups for legacy drm/fbdev drivers"
* tag 'drm-next-2020-12-18' of git://anongit.freedesktop.org/drm/drm: (117 commits)
drm/qxl: don't allocate a dma_address array
drm/nouveau: fix multihop when move doesn't work.
drm/i915/tgl: Fix REVID macros for TGL to fetch correct stepping
drm/i915: Fix mismatch between misplaced vma check and vma insert
drm/i915/perf: also include Gen11 in OATAILPTR workaround
Revert "drm/i915: re-order if/else ladder for hpd_irq_setup"
drm/amdgpu/disply: fix documentation warnings in display manager
drm/amdgpu: print mmhub client name for dimgrey_cavefish
drm/amdgpu: set mode1 reset as default for dimgrey_cavefish
drm/amd/display: Add get_dig_frontend implementation for DCEx
drm/radeon: remove h from printk format specifier
drm/amdgpu: remove h from printk format specifier
drm/amdgpu: Fix spelling mistake "Heterogenous" -> "Heterogeneous"
drm/amdgpu: fix regression in vbios reservation handling on headless
drm/amdgpu/SRIOV: Extend VF reset request wait period
drm/amdkfd: correct amdgpu_amdkfd_gpuvm_alloc_memory_of_gpu log.
drm/amd/display: Adding prototype for dccg21_update_dpp_dto()
drm/amdgpu: print what method we are using for runtime pm
drm/amdgpu: simplify logic in atpx resume handling
drm/amdgpu: no need to call pci_ignore_hotplug for _PR3
...
Since we allow removing the timeline map at runtime, there is a risk
that rq->hwsp points into a stale page. To control that risk, we hold
the RCU read lock while reading *rq->hwsp, but we missed a couple of
important barriers. First, the unpinning / removal of the timeline map
must be after all RCU readers into that map are complete, i.e. after an
rcu barrier (in this case courtesy of call_rcu()). Secondly, we must
make sure that the rq->hwsp we are about to dereference under the RCU
lock is valid. In this case, we make the rq->hwsp pointer safe during
i915_request_retire() and so we know that rq->hwsp may become invalid
only after the request has been signaled. Therefore is the request is
not yet signaled when we acquire rq->hwsp under the RCU, we know that
rq->hwsp will remain valid for the duration of the RCU read lock.
This is a very small window that may lead to either considering the
request not completed (causing a delay until the request is checked
again, any wait for the request is not affected) or dereferencing an
invalid pointer.
Fixes: 3adac4689f ("drm/i915: Introduce concept of per-timeline (context) HWSP")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.1+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218122421.18344-1-chris@chris-wilson.co.uk
Fix TGL REVID macros to fetch correct display/gt stepping based
on SOC rev id from INTEL_REVID() macro. Previously, we were just
returning the first element of the revid array instead of using
the correct index based on SOC rev id.
Fixes: c33298cb34 ("drm/i915/tgl: Fix stepping WA matching")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203072359.156682-1-aditya.swarup@intel.com
(cherry picked from commit 83dbd74f82)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When inserting a VMA, we restrict the placement to the low 4G unless the
caller opts into using the full range. This was done to allow usersapce
the opportunity to transition slowly from a 32b address space, and to
avoid breaking inherent 32b assumptions of some commands.
However, for insert we limited ourselves to 4G-4K, but on verification
we allowed the full 4G. This causes some attempts to bind a new buffer
to sporadically fail with -ENOSPC, but at other times be bound
successfully.
commit 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1
page") suggests that there is a genuine problem with stateless addressing
that cannot utilize the last page in 4G and so we purposefully excluded
it. This means that the quick pin pass may cause us to utilize a buggy
placement.
Reported-by: CQ Tang <cq.tang@intel.com>
Testcase: igt/gem_exec_params/larger-than-life-batch
Fixes: 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1 page")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: CQ Tang <cq.tang@intel.com>
Reviewed-by: CQ Tang <cq.tang@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v4.5+
Link: https://patchwork.freedesktop.org/patch/msgid/20201216092951.7124-1-chris@chris-wilson.co.uk
(cherry picked from commit 5f22cc0b13)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We now use ilk_hpd_irq_setup for all GMCH platforms that do not have
hotplug. These are early gen3 and gen2 devices that now explode on boot
as they try to access non-existent registers.
Fixes: 794d61a190 ("drm/i915: re-order if/else ladder for hpd_irq_setup")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127145748.29491-1-chris@chris-wilson.co.uk
(cherry picked from commit e5346a1ff3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add bound checks for TGL REV ID array. Since, there might
be a possibility of using older kernels on latest platform
revisions, resulting in out of bounds access for rev ID array.
In this scenario, use the latest rev ID available and apply
those WAs.
Also, modify GT macros for TGL rev ID to reuse tgl_revids_get().
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203072359.156682-2-aditya.swarup@intel.com
Fix TGL REVID macros to fetch correct display/gt stepping based
on SOC rev id from INTEL_REVID() macro. Previously, we were just
returning the first element of the revid array instead of using
the correct index based on SOC rev id.
Fixes: c33298cb34 ("drm/i915/tgl: Fix stepping WA matching")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203072359.156682-1-aditya.swarup@intel.com
Since we wake the GT up before executing a request, and go to sleep as
soon as it is retired, the GT wake time not only represents how long the
device is powered up, but also provides a summary, albeit an overestimate,
of the device runtime (i.e. the rc0 time to compare against rc6 time).
v2: s/busy/awake/
v3: software-gt-awake-time and I915_PMU_SOFTWARE_GT_AWAKE_TIME
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154456.13954-1-chris@chris-wilson.co.uk
Matthew Brost pointed out that the while-loop on a shared breadcrumb was
inherently fraught with danger as it competed with the other users of
the breadcrumbs. However, in order to completely drain the re-arming irq
worker, the while-loop is a necessity, despite my optimism that we could
force cancellation with a couple of irq_work invocations.
Given that we can't merely drop the while-loop, use an activity counter on
the breadcrumbs to detect when we are parking the breadcrumbs for the
last time.
Based on a patch by Matthew Brost.
Reported-by: Matthew Brost <matthew.brost@intel.com>
Suggested-by: Matthew Brost <matthew.brost@intel.com>
Fixes: 9d5612ca16 ("drm/i915/gt: Defer enabling the breadcrumb interrupt to after submission")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201217091524.10258-1-chris@chris-wilson.co.uk
Use the wait_queue_entry.flags to denote the special fence behaviour
(flattening continuations along fence chains, and for propagating
errors) rather than trying to detect ordinary waiters by their
functions.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201216165850.25030-1-chris@chris-wilson.co.uk
The free_list and worker was introduced in commit 5f09a9c8ab ("drm/i915:
Allow contexts to be unreferenced locklessly"), but subsequently made
redundant by the removal of the last sleeping lock in commit 2935ed5339
("drm/i915: Remove logical HW ID"). As we can now free the GEM context
immediately from any context, remove the deferral of the free_list
v2: Lift removing the context from the global list into close().
Suggested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215152138.8158-1-chris@chris-wilson.co.uk
When inserting a VMA, we restrict the placement to the low 4G unless the
caller opts into using the full range. This was done to allow usersapce
the opportunity to transition slowly from a 32b address space, and to
avoid breaking inherent 32b assumptions of some commands.
However, for insert we limited ourselves to 4G-4K, but on verification
we allowed the full 4G. This causes some attempts to bind a new buffer
to sporadically fail with -ENOSPC, but at other times be bound
successfully.
commit 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1
page") suggests that there is a genuine problem with stateless addressing
that cannot utilize the last page in 4G and so we purposefully excluded
it. This means that the quick pin pass may cause us to utilize a buggy
placement.
Reported-by: CQ Tang <cq.tang@intel.com>
Testcase: igt/gem_exec_params/larger-than-life-batch
Fixes: 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1 page")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: CQ Tang <cq.tang@intel.com>
Reviewed-by: CQ Tang <cq.tang@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v4.5+
Link: https://patchwork.freedesktop.org/patch/msgid/20201216092951.7124-1-chris@chris-wilson.co.uk
Now that relay_open() accepts const callbacks, make relay callbacks const.
Link: https://lkml.kernel.org/r/534d089f413db98aa0b94773fa49d5275d0d3c25.1606153547.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With GEN11_HOTPLUG_CTL_LONG_DETECT(), SHOTPLUG_CTL_DDI_HPD_LONG_DETECT()
and ICP_TC_HPD_LONG_DETECT() taking the hpd_pin as their argument
we can remove some duplication in the long_detect() switch statements.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204182309.14213-1-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Driver code has no business with the internals of the irq descriptor.
Aside of that the count is per interrupt line and therefore takes
interrupts from other devices into account which share the interrupt line
and are not handled by the graphics driver.
Replace it with a pmu private count which only counts interrupts which
originate from the graphics card.
To avoid atomics or heuristics of some sort make the counter field
'unsigned long'. That limits the count to 4e9 on 32bit which is a lot and
postprocessing can easily deal with the occasional wraparound.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://lore.kernel.org/r/20201210194043.957046529@linutronix.de
Nothing uses the result and nothing should ever use it in driver code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20201210194043.862572239@linutronix.de
To support legacy gamma ioctls the drivers need to set
drm_crtc_funcs.gamma_set either to a custom implementation or to
drm_atomic_helper_legacy_gamma_set. Most of the atomic drivers do the
latter.
We can simplify this by making the core handle it automatically.
Move the drm_atomic_helper_legacy_gamma_set() functionality into
drm_color_mgmt.c to make drm_mode_gamma_set_ioctl() use
drm_crtc_funcs.gamma_set if set or GAMMA_LUT property if not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201211114237.213288-2-tomi.valkeinen@ti.com
- migrate_disable/enable() support which originates from the RT tree and
is now a prerequisite for the new preemptible kmap_local() API which aims
to replace kmap_atomic().
- A fair amount of topology and NUMA related improvements
- Improvements for the frequency invariant calculations
- Enhanced robustness for the global CPU priority tracking and decision
making
- The usual small fixes and enhancements all over the place
-----BEGIN PGP SIGNATURE-----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=Oz1V
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Thomas Gleixner:
- migrate_disable/enable() support which originates from the RT tree
and is now a prerequisite for the new preemptible kmap_local() API
which aims to replace kmap_atomic().
- A fair amount of topology and NUMA related improvements
- Improvements for the frequency invariant calculations
- Enhanced robustness for the global CPU priority tracking and decision
making
- The usual small fixes and enhancements all over the place
* tag 'sched-core-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (61 commits)
sched/fair: Trivial correction of the newidle_balance() comment
sched/fair: Clear SMT siblings after determining the core is not idle
sched: Fix kernel-doc markup
x86: Print ratio freq_max/freq_base used in frequency invariance calculations
x86, sched: Use midpoint of max_boost and max_P for frequency invariance on AMD EPYC
x86, sched: Calculate frequency invariance for AMD systems
irq_work: Optimize irq_work_single()
smp: Cleanup smp_call_function*()
irq_work: Cleanup
sched: Limit the amount of NUMA imbalance that can exist at fork time
sched/numa: Allow a floating imbalance between NUMA nodes
sched: Avoid unnecessary calculation of load imbalance at clone time
sched/numa: Rename nr_running and break out the magic number
sched: Make migrate_disable/enable() independent of RT
sched/topology: Condition EAS enablement on FIE support
arm64: Rebuild sched domains on invariance status changes
sched/topology,schedutil: Wrap sched domains rebuild
sched/uclamp: Allow to reset a task uclamp constraint value
sched/core: Fix typos in comments
Documentation: scheduler: fix information on arch SD flags, sched_domain and sched_debug
...
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support
-----BEGIN PGP SIGNATURE-----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=c9rl
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
Chris spotted that since 16ffe73c18 ("drm/i915/pmu: Use GT parked for
estimating RC6 while asleep") we don't rely on runtime pm internals when
estimating RC6 while asleep. We can remove the ifdef code to simplify and
at the same time wake up the device less when querying RC6 if CONFIG_PM is
not compiled in.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
References: 16ffe73c18 ("drm/i915/pmu: Use GT parked for estimating RC6 while asleep")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201214094349.3563876-3-tvrtko.ursulin@linux.intel.com
Chris found a CI report which points out calling intel_runtime_pm_get from
inside i915_pmu_enable hook is not allowed since it can be invoked from
hard irq context. This is something we knew but forgot, so lets fix it
once again.
We do this by syncing the internal book keeping with hardware rc6 counter
on driver load.
v2:
* Always sync on parking and fully sync on init.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: f4e9894b69 ("drm/i915/pmu: Correct the rc6 offset upon enabling")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201214094349.3563876-1-tvrtko.ursulin@linux.intel.com
Reduce the module/device probe error into a mere debug to hide issues
where the initial modeset is failing (after lies told by hw probe) and
the system hangs with a livelock in cleaning up the failed commit.
Reported-by: H.J. Lu <hjl.tools@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=210619
Fixes: b3bf99daae ("drm/i915/display: Defer initial modeset until after GGTT is initialised")
Fixes: ccc9e67ab2 ("drm/i915/display: Defer initial modeset until after GGTT is initialised")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201210230741.17140-1-chris@chris-wilson.co.uk
When we reset the legacy ring context, due to potential corruption over
suspend/resume, remove the valid bit so that we avoid loading garbage.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201210080240.24529-1-chris@chris-wilson.co.uk
The above workaround was added as an engine workaround not a GT
workaround. Moved it to the correct location.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201210170615.3107266-1-lucas.demarchi@intel.com
For an enabled DSC during HW readout the corresponding power reference
is taken along the CRTC power domain references in
get_crtc_power_domains(). Remove the incorrect get ref from the DSI
encoder hook.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209153952.3397959-1-imre.deak@intel.com
Move the initialization of the rc_model_size from the common code into
encoder code, allowing different encoders to specify the size according
to their needs. Keep using the hard coded value in the encoders for now
to make this a non-functional change.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6843c4f6958619f7389180aa92fded7b9fdbb4ba.1607429866.git.jani.nikula@intel.com
The rc_model_size is specified in the DSC config, and the hardware
programming should respect that instead of hard coding a value of 8192.
Regardless, the rc_model_size in DSC config is currently hard coded to
the same value, so this should have no impact, other than allowing the
use of other sizes as needed.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/27d86ad25832bbb985f6e996f3d02dca01a66895.1607429866.git.jani.nikula@intel.com
These functions are independent from the backend used and can therefore
be split out of the exelists submission file, so they can be re-used by
the upcoming GuC submission backend.
Based on a patch by Chris Wilson.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209233618.4287-3-chris@chris-wilson.co.uk
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We want to separate the utility functions for controlling the logical
ring context from the execlists submission mechanism (which is an
overgrown scheduler).
This is similar to Daniele's work to split up the files, but being
selfish I wanted to base it after my own changes to intel_lrc.c petered
out.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209233618.4287-2-chris@chris-wilson.co.uk
Cleanup intel_lrc.h by moving some of the residual common register
definitions into intel_lrc_reg.h, prior to rebranding and splitting off
the submission backends.
v2: keep the SCHEDULE enum in the old file, since it is specific to the
gvt usage of the execlists submission backend (John)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> #v2
Cc: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209233618.4287-1-chris@chris-wilson.co.uk
Tigerlake is plagued by spontaneous DMAR faults [reason 7, next page
table ptr is invalid] which lead to GPU hangs. These faults occur when
an iommu map is immediately reused. Adding further clflushes and
barriers around either the GTT PTE or iommu PTE updates do not prevent
the faults. So far the only effect has been from inducing a delay
between reuse of the iommu on the GPU, and applying the delay at the
iommu map allows for the smallest stable delay.
Note that such a delay is hideous and clearly does not fix the root cause,
and so should only be a bandaid until a complete solution is found. The
delay was determined by running igt/gem_exec_fence/parallel in a loop for
a few hours (unpatched MTBF is about 10s).
We have also seen such DMAR fault [reason 7] errors on other platforms,
notably gen9-gen11, but so far it has only been trivially and
consistently reproduced on Tigerlake.
v2: Leave a tell-tale to know when we apply the vt'd quirk, and as a
reminder to remove it again. Hopefully.
Testcase: igt/gem_exec_fence/parallel
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209164008.5487-2-chris@chris-wilson.co.uk
A call to wait for the GT to idle from inside the put_pages fallback is
prone to cause an uninterruptible livelock. As it does not provide
adequate serialisation with new requests, simply fallback to a trivial
sleep.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209164008.5487-1-chris@chris-wilson.co.uk
Document what a masked register is according to bspec so we avoid
developers using the wrong functions to implement WAs.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209045246.2905675-3-lucas.demarchi@intel.com
The use of "masked" in this function is due to its history. Once upon a
time it received a mask and a value as parameter. Since
commit eeec73f8a4 ("drm/i915/gt: Skip rmw for masked registers")
that is not true anymore and now there is a clear and a set parameter.
Depending on the case, that can still be thought as a mask and value,
but there are some subtle differences: what we clear doesn't need to be
the same bits we are setting, particularly when we are using masked
registers.
The fact that we also have "masked registers", i.e. registers whose mask
is stored in the upper 16 bits of the register, makes it even more
confusing, because "masked" in wa_write_masked_or() has little to do
with masked registers, but rather refers to the old mask parameter the
function received (that can also, but not exclusively, be used to write
to masked register).
Avoid the ambiguity and misnomer by renaming it to something else,
hopefully less confusing: wa_write_clr_set(), to designate that we are
doing both clr and set operations in the register.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209045246.2905675-2-lucas.demarchi@intel.com
When using masked registers, there is nothing to clear since a masked
register has the mask in the upper 16b: we can just write to the
location we want and use the mask to control what bits we are writing
to.
However that doesn't mean we don't want to read back the register and
check the value actually matched what we wanted to write, i.e. that
the WA stick. That should be an explicit opt-out for registers that are
either write-only or that are affected by hardware misbehavior.
Moreover both wa_masked_en() and wa_masked_dis() check the WA stick, so
skipping the check just because the field is more than 1 bit is
surprising and error-prone.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209045246.2905675-1-lucas.demarchi@intel.com
We checked the table size against a hardcoded number of entries, and
that number was excluding the special mocs registers at the end.
Fixes: 777a7717d6 ("drm/i915/gt: Program mocs:63 for cache eviction on gen9")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.3+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127102540.13117-1-chris@chris-wilson.co.uk
(cherry picked from commit 444fbf5d70)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[backported and updated the Fixes sha]
This patch fixes the slice count computation algorithm
for calculating the slice count based on Peak pixel rate
and the max slice width allowed on the DSC engines.
We need to ensure slice count > min slice count req
as per DP spec based on peak pixel rate and that it is
greater than min slice count based on the max slice width
advertised by DPCD. So use max of these two.
In the prev patch we were using min of these 2 causing it
to violate the max slice width limitation causing a blank
screen on 8K@60.
Fixes: d9218c8f6c ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204205804.25225-1-manasi.d.navare@intel.com
(cherry picked from commit d371d6ea92)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently the check that the unsigned size_t variable i is >= 0
is always true because the unsigned variable will never be negative,
causing the loop to run forever. Fix this by changing the
pre-decrement check to a zero check on i followed by a decrement of i.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: bfed6708d6 ("drm/i915: use vmap in shmem_pin_map")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002170354.94627-1-colin.king@canonical.com
(cherry picked from commit e70956a249)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We currently presume that the engine reset is successful, cancelling the
expired preemption timer in the process. However, engine resets can
fail, leaving the timeout still pending and we will then respond to the
timeout again next time the tasklet fires. What we want is for the
failed engine reset to be promoted to a full device reset, which is
kicked by the heartbeat once the engine stops processing events.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1168
Fixes: 3a7a92aba8 ("drm/i915/execlists: Force preemption")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151234.19729-2-chris@chris-wilson.co.uk
(cherry picked from commit d997e240ce)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Before reseting the engine, we suspend the execution of the guilty
request, so that we can continue execution with a new context while we
slowly compress the captured error state for the guilty context. However,
if the reset fails, we will promptly attempt to reset the same request
again, and discover the ongoing capture. Ignore the second attempt to
suspend and capture the same request.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1168
Fixes: 32ff621fd7 ("drm/i915/gt: Allow temporary suspension of inflight requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v5.7+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151234.19729-1-chris@chris-wilson.co.uk
(cherry picked from commit b969540500)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In the course of discovering and closing many races with context closure
and execbuf submission, since commit 61231f6bd0 ("drm/i915/gem: Check
that the context wasn't closed during setup") we started checking that
the context was not closed by another userspace thread during the execbuf
ioctl. In doing so we cancelled the inflight request (by telling it to be
skipped), but kept reporting success since we do submit a request, albeit
one that doesn't execute. As the error is known before we return from the
ioctl, we can report the error we detect immediately, rather than leave
it on the fence status. With the immediate propagation of the error, it
is easier for userspace to handle.
Fixes: 61231f6bd0 ("drm/i915/gem: Check that the context wasn't closed during setup")
Testcase: igt/gem_ctx_exec/basic-close-race
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v5.7+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203103432.31526-1-chris@chris-wilson.co.uk
(cherry picked from commit ba38b79eae)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There is a copy and paste bug in this code. It's supposed to check
"obj2" instead of checking "obj" a second time.
Fixes: 80f0b679d6 ("drm/i915: Add an implementation for i915_gem_ww_ctx locking, v2.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/8ilneOcJAjwqU4t@mwand
(cherry picked from commit 14f2d7604f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Closed vma are protected by the GT wakeref held as we lookup the vma, so
we know that the vma will not be freed as we process it for the execbuf.
Instead we expect to catch the closed status of the context, and simply
allow the close-race on an individual vma to be washed away.
Longer term, the GT wakeref protection will be removed by explicit
vma.kref tracking.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2245
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201207193824.18114-1-chris@chris-wilson.co.uk
This patch fixes the slice count computation algorithm
for calculating the slice count based on Peak pixel rate
and the max slice width allowed on the DSC engines.
We need to ensure slice count > min slice count req
as per DP spec based on peak pixel rate and that it is
greater than min slice count based on the max slice width
advertised by DPCD. So use max of these two.
In the prev patch we were using min of these 2 causing it
to violate the max slice width limitation causing a blank
screen on 8K@60.
Fixes: d9218c8f6c ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204205804.25225-1-manasi.d.navare@intel.com
The Bspec does not mention polling the FEC Enable
Live status bit. That is only there for debug purposes.
So remove the polling from driver.
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201125072634.27664-1-manasi.d.navare@intel.com
When we fail to find a single block large enough to require splitting,
report the largest block we did find.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201207130346.11849-1-chris@chris-wilson.co.uk
Currently the check that the unsigned size_t variable i is >= 0
is always true because the unsigned variable will never be negative,
causing the loop to run forever. Fix this by changing the
pre-decrement check to a zero check on i followed by a decrement of i.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: bfed6708d6 ("drm/i915: use vmap in shmem_pin_map")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002170354.94627-1-colin.king@canonical.com
Remove the last macro and implement it as a function like the rest of
the operations that don't assume there is a `wal` list, but rather
receive it as argument.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201205092542.2325477-4-lucas.demarchi@intel.com
Just ommitting the list it's operating on doesn't save much typing
and adds another way to do the same thing. Just replace it with
wa_masked_dis().
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201205092542.2325477-3-lucas.demarchi@intel.com
Just ommitting the list it's operating on doesn't save much typing and
adds another way to do the same thing. Just replace it with
wa_masked_en().
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201205092542.2325477-2-lucas.demarchi@intel.com
Set GS Timer to 224 to prevent a HS/DS hang.
Bspec: 53508
v2: reword commit message and add comment explaining why read
verification is ignored (Chris)
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201205092542.2325477-1-lucas.demarchi@intel.com
Switch off the scanout during driver unregister, so we can shutdown the
HW immediately for unbind.
v2: Remove the old shutdown from remove, it should now be redundant.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204161601.20897-1-chris@chris-wilson.co.uk
Let's do the kill_bigjoiner_slave() thing from
intel_bigjoiner_add_affected_crtcs() since it's related to
what we do there. This cleans up the logic in the
compute_config() loop a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201124201156.17095-4-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
If either of the bigjoiner pipes needs a modeset then we need
a modeset on both pipes. Make it so.
v2: Split out the kill_bigjoiner_slave() change (Manasi)
Add affected connectors/planes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201124201156.17095-3-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
drm_atomic_add_affected_planes() only considers planes which
are logically enabled in the uapi state. For bigjoiner we need
to consider planes logically enabled in the hw state. Add a
helper for that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201124201156.17095-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Currently crtc_state->uapi.plane_mask only tracks logically
enabled planes on the uapi level. For bigjoiner purposes
we want to do the same for the hw state. Let's follow the
pattern established by active_planes & co. here.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201124201156.17095-1-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Across a reset, we stop the engine but not the timers. This leaves a
window where the timers have inconsistent state with the engine, but
should only result in a spurious timeout. As we cancel the outstanding
events, also cancel their timers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151234.19729-4-chris@chris-wilson.co.uk
We currently presume that the engine reset is successful, cancelling the
expired preemption timer in the process. However, engine resets can
fail, leaving the timeout still pending and we will then respond to the
timeout again next time the tasklet fires. What we want is for the
failed engine reset to be promoted to a full device reset, which is
kicked by the heartbeat once the engine stops processing events.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1168
Fixes: 3a7a92aba8 ("drm/i915/execlists: Force preemption")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151234.19729-2-chris@chris-wilson.co.uk
Before reseting the engine, we suspend the execution of the guilty
request, so that we can continue execution with a new context while we
slowly compress the captured error state for the guilty context. However,
if the reset fails, we will promptly attempt to reset the same request
again, and discover the ongoing capture. Ignore the second attempt to
suspend and capture the same request.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1168
Fixes: 32ff621fd7 ("drm/i915/gt: Allow temporary suspension of inflight requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v5.7+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151234.19729-1-chris@chris-wilson.co.uk
In the course of discovering and closing many races with context closure
and execbuf submission, since commit 61231f6bd0 ("drm/i915/gem: Check
that the context wasn't closed during setup") we started checking that
the context was not closed by another userspace thread during the execbuf
ioctl. In doing so we cancelled the inflight request (by telling it to be
skipped), but kept reporting success since we do submit a request, albeit
one that doesn't execute. As the error is known before we return from the
ioctl, we can report the error we detect immediately, rather than leave
it on the fence status. With the immediate propagation of the error, it
is easier for userspace to handle.
Fixes: 61231f6bd0 ("drm/i915/gem: Check that the context wasn't closed during setup")
Testcase: igt/gem_ctx_exec/basic-close-race
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v5.7+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203103432.31526-1-chris@chris-wilson.co.uk
Throw away all the debugfs entries that are not being actively used for
debugging/developing IGT. Note that a couple of these are already and
will remain available under the gt/
Files removed:
i915_gem_fence_regs
i915_gem_interrupt
i915_ring_freq_table
i915_context_status
i915_llc
i915_shrinker_info
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201202112140.16759-1-chris@chris-wilson.co.uk
All the display power domain references are wakeref tracked now, so we
can mark intel_display_power_put_unchecked() as an internal function
(for suppressing wakeref tracking in non-debug builds).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130212200.2811939-10-imre.deak@intel.com
Add wakeref tracking for the display power domain reference taken to
keep the display power well functionality disabled.
v2: Add missing wakeref zeroing to intel_power_domains_driver_remove()
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201201161340.2879202-2-imre.deak@intel.com
Rename power_domains.wakeref to power_domains.init_wakeref to make the
use of this reference clearer. The next patch adds tracking for another
power reference user of the power_domains functionality.
While at it add a missing zero wakeref assert when setting the wakeref.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130212200.2811939-8-imre.deak@intel.com
Factor out helper functions to get/put a set of power domains that are
tracked using their wakeref handles. The same is needed by the next
patch adding tracking for enabled CRTC power domains.
v2: s/uint64_t/u64/ (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201201161340.2879202-1-imre.deak@intel.com
The for_each_oldnew_intel_crtc_in_state() iterator index does match
crtc->pipe, but using the same thing as array index when getting and
putting CRTC power domains makes things clearer.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130212200.2811939-2-imre.deak@intel.com
There is a copy and paste bug in this code. It's supposed to check
"obj2" instead of checking "obj" a second time.
Fixes: 80f0b679d6 ("drm/i915: Add an implementation for i915_gem_ww_ctx locking, v2.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/8ilneOcJAjwqU4t@mwand
This moves the functions into static const instead of having
funcs and data in the same struct.
It leaves the power callback alone, as it is used in a different
manner.
v2: leave power callback alone (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130210945.31850-1-airlied@gmail.com
In most cases, we are better off letting the compiler decide whether to
inline static functions in .c files or not. In this case, the inline
will be ignored anyway as mmio_pm_restore_handler() is passed as a
function pointer.
Fixes: 5f60b12edc ("drm/i915/gvt: Save/restore HW status to support GVT suspend/resume")
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Hang Yuan <hang.yuan@linux.intel.com>
Cc: Colin Xu <colin.xu@intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: intel-gvt-dev@lists.freedesktop.org
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20201130111353.25406-1-jani.nikula@intel.com
drm/i915 features for v5.11:
Highlights:
- Enable big joiner to join two pipes to one port to overcome pipe restrictions
(Manasi, Ville, Maarten)
Display:
- More DG1 enabling (Lucas, Aditya)
- Fixes to cases without display (Lucas, José, Jani)
- Initial PSR state improvements (José)
- JSL eDP vswing updates (Tejas)
- Handle EDID declared max 16 bpc (Ville)
- Display refactoring (Ville)
Other:
- GVT features
- Backmerge
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87czzzkk1s.fsf@intel.com
!HAS_DISPLAY() implies !HAS_OVERLAY(), skipping overlay setup anyway, so
return earlier from intel_modeset_init() for clarity.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106225531.920641-4-lucas.demarchi@intel.com
(cherry picked from commit 71c8415d0d)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We treat idling the GT (intel_rps_park) as a downclock event, and reduce
the frequency we intend to restart the GT with. Since the two workloads
are likely related (e.g. a compositor rendering every 16ms), we want to
carry the frequency and load information from across the idling.
However, we do also need to update the frequencies so that workloads
that run for less than 1ms are autotuned by RPS (otherwise we leave
compositors running at max clocks, draining excess power). Conversely,
if we try to run too slowly, the next workload has to run longer. Since
there is a hysteresis in the power graph, below a certain frequency
running a short workload for longer consumes more energy than running it
slightly higher for less time. The exact balance point is unknown
beforehand, but measurements with 30fps media playback indicate that RPe
is a better choice.
Reported-by: Edward Baker <edward.baker@intel.com>
Tested-by: Edward Baker <edward.baker@intel.com>
Fixes: 043cd2d14e ("drm/i915/gt: Leave rps->cur_freq on unpark")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Edward Baker <edward.baker@intel.com>
Cc: Andi Shyti <andi.shyti@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201124183521.28623-1-chris@chris-wilson.co.uk
(cherry picked from commit f7ed83cc19)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
As we use a shmemfs file to hold the context state, when not in use it
may be swapped out, such as across suspend. Since we wrote into the
shmemfs without marking the pages as dirty, the contents may be dropped
instead of being written back to swap. On re-using the shmemfs file,
such as creating a new context after resume, the contents of that file
were likely garbage and so the new context could then hang the GPU.
Simply mark the page as being written when copying into the shmemfs
file, and it the new contents will be retained across swapout.
Fixes: be1cb55a07 ("drm/i915/gt: Keep a no-frills swappable copy of the default context state")
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: Venkata Ramana Nayana <venkata.ramana.nayana@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v5.8+
Link: https://patchwork.freedesktop.org/patch/msgid/20201127120718.454037-161-matthew.auld@intel.com
(cherry picked from commit a9d71f76cc)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Allow a brief period for continued access to a dead intel_context by
deferring the release of the struct until after an RCU grace period.
As we are using a dedicated slab cache for the contexts, we can defer
the release of the slab pages via RCU, with the caveat that individual
structs may be reused from the freelist within an RCU grace period. To
handle that, we have to avoid clearing members of the zombie struct.
This is required for a later patch to handle locking around virtual
requests in the signaler, as those requests may want to move between
engines and be destroyed while we are holding b->irq_lock on a physical
engine.
v2: Drop mutex_reinit(), if we never mark the mutex as destroyed we
don't need to reset the debug code, at the loss of having the mutex
debug code spot us attempting to destroy a locked mutex.
v3: As the intended use will remain strongly referenced counted, with
very little inflight access across reuse, drop the ctor.
v4: Drop the unrequired change to remove the temporary reference around
dropping the active context, and add back some more missing ctor
operations.
v5: The ctor is back. Tvrtko spotted that ce->signal_lock [introduced
later] maybe accessed under RCU and so needs special care not to be
reinitialised.
v6: Don't mix SLAB_TYPESAFE_BY_RCU and RCU list iteration.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201126140407.31952-3-chris@chris-wilson.co.uk
(cherry picked from commit 14d1eaf088)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since we try and estimate how long we require to update the registers to
perform a plane update, it is of vital importance that we measure the
distribution of plane updates to better guide our estimate. If we
underestimate how long it takes to perform the plane update, we may
slip into the next scanout frame causing a tear. If we overestimate, we
may unnecessarily delay the update to the next frame, causing visible
jitter.
Replace the warning that we exceed some arbitrary threshold for the
vblank update with a histogram for debugfs.
v2: Add a per-crtc debugfs entry so that the information is easier to
extract when testing individual CRTC, and so that it can be reset before
a test.
v3: Flip the graph on its side; creates space to label the time axis.
Updates: 4684
|
1us |
|
4us |********
|**********
16us |***********
|*****
66us |
|
262us |
|
1ms |
|
4ms |
|
17ms |
|
Min update: 5918ns
Max update: 54781ns
Average update: 16628ns
Overruns > 250us: 0
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1982
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20201202212814.26320-1-chris@chris-wilson.co.uk
Mixing I915_ALLOC_CONTIGUOUS and I915_ALLOC_MAX_SEGMENT_SIZE fared
badly. The two directives conflict, with the contiguous request setting
the min_order to the full size of the object, and the max-segment-size
setting the max_order to the limit of the DMA mapper. This results in a
situation where max_order < min_order, causing our sanity checks to
fail.
Instead of limiting the buddy block size, in the previous patch we split
the oversized buddy into multiple scatterlist elements.
Fixes: d2cf0125d4 ("drm/i915/lmem: Limit block size to 4G")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201202173444.14903-2-chris@chris-wilson.co.uk
Adhere to the i915_sg_max_segment() limit on the lengths of individual
scatterlist elements, and in doing so split up very large chunks of lmem
into manageable pieces for the dma-mapping backend.
Reported-by: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Suggested-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201202173444.14903-1-chris@chris-wilson.co.uk
Good riddance! Remove the macros and their remaining references in
comments.
The following functions should be used instead, depending on the use
case:
- intel_uncore_read(), intel_uncore_write(), intel_uncore_posting_read()
- intel_de_read(), intel_de_write(), intel_de_posting_read()
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130111601.2817-10-jani.nikula@intel.com
There are some corner cases wrt underrun when we enable
FBC with PSR2 on TGL. Recommendation from hardware is to
keep this combination disabled.
Bspec: 50422 HSD: 14010260002
v2: Added psr2 enabled check from crtc_state (Anshuman)
Added Bspec link and HSD referneces (Jose)
v3: Moved the logic to disable fbc to intel_fbc_update_state_cache
and removed the crtc->config usages, as per Ville's recommendation.
v4: Introduced a variable in fbc state_cache instead of the earlier
plane.visible WA, as suggested by Jose.
v5: Dropped an extra check for fbc in intel_fbc_enable and addressed
review comments by Jose.
v6: Move WA to end of function and added Jose's RB.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201201190406.1752-2-uma.shankar@intel.com
Adding any kinds of "last" abi markers is usually a mistake which I
repeated when implementing the PMU because it felt convenient at the time.
This patch marks I915_PMU_LAST as deprecated and stops the internal
implementation using it for sizing the event status bitmask and array.
New way of sizing the fields is a bit less elegant, but it omits reserving
slots for tracking events we are not interested in, and as such saves some
runtime space. Adding sampling events is likely to be a special event and
the new plumbing needed will be easily detected in testing. Existing
asserts against the bitfield and array sizes are keeping the code safe.
First event which gets the new treatment in this new scheme are the
interrupts - which neither needs any tracking in i915 pmu nor needs
waking up the GPU to read it.
v2:
* Streamline helper names. (Chris)
v3:
* Comment which events need tracking. (Chris)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201201131757.206367-1-tvrtko.ursulin@linux.intel.com
Let's avoid adding new I915_WRITE uses while we try to get rid of them.
Fixes: 5f60b12edc ("drm/i915/gvt: Save/restore HW status to support GVT suspend/resume")
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Hang Yuan <hang.yuan@linux.intel.com>
Cc: Colin Xu <colin.xu@intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: intel-gvt-dev@lists.freedesktop.org
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130111601.2817-9-jani.nikula@intel.com
Implement Read back of HDR metadata infoframes i.e Dynamic Range
and Mastering Infoframe for LSPCON devices.
v2: Added proper bitmask of enabled infoframes as per Ville's
recommendation.
v3: Dropped a redundant wrapper as per Ville's comment.
v4: Dropped a redundant print, added Ville's RB.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-14-uma.shankar@intel.com
Implemented Infoframes enabled readback for LSPCON devices.
This will help align the implementation with state readback
infrastructure.
v2: Added proper bitmask of enabled infoframes as per Ville's
recommendation.
v3: Added pcon specific infoframe types instead of using the HSW
one's, as recommended by Ville.
v4: Addressed Ville's review comment by adding HDMI infoframe
versions directly instead of DIP wrappers.
v5: Re-ordered the patches to avoid potential break in usage,
as suggested by Ville.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-13-uma.shankar@intel.com
Lspcon has Infoframes as well as DIP for HDR metadata(DRM Infoframe).
Create a separate mechanism for lspcon compared to HDMI in order to
address the same and ensure future scalability.
v2: Streamlined this as per Ville's suggestions, making sure that
HDMI infoframe versions are directly returned instead of a redundant
and confusing DIP overhead.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-12-uma.shankar@intel.com
Enable HDR for LSPCON based on Parade along with MCA.
v2: Added a helper for status reg as suggested by Ville.
v3: Removed a redundant variable, added Ville's RB.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Vipin Anand <vipin.anand@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-11-uma.shankar@intel.com
Enable HDMI Colorspace for LSPCON based devices. Sending Colorimetry
data for HDR using AVI infoframe. LSPCON firmware expects this and though
SOC drives DP, for HDMI panel AVI infoframe is sent to the LSPCON device
which transfers the same to HDMI sink.
v2: Dropped state managed in drm core as per Jani Nikula's suggestion.
v3: Aligned colorimetry handling for lspcon as per compute_avi_infoframes,
as suggested by Ville.
v4: Finally fixed this with Ville's help, re-phrased the commit header
and description.
v5: Register HDMI colorspace for lspcon and move this to
intel_dp_add_properties as we can't create property at late_register.
Credits-to: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-9-uma.shankar@intel.com
With LSPCON we use the AVI infoframe to convey the colorimetry
information (as opposed to DP MSA/SDP), so the property we expose
should match the values we can stuff into the infoframe. Ie. we
must use the HDMI variant of the property, even though we drive
LSPCON in PCON mode. To that end just split
intel_attach_colorspace_property() into HDMI and DP variants
and let the caller worry about which one it wants to use.
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-8-uma.shankar@intel.com
Content type is supported on HDMI sink devices. Attached the
property for the same for LSPCON based devices.
v2: Added the content type programming when we are attaching
the property to connector, as suggested by Ville.
v3: Need to attach content type on intel_dp_add_properties
as creating of new properties is not possible at late_register.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-7-uma.shankar@intel.com
Attach HDR property for Gen9 devices with MCA LSPCON
chips.
v2: Cleaned HDR property attachment logic based on capability
as per Jani Nikula's suggestion.
v3: Fixed the HDR property attachment logic as per the new changes
by Kai-Feng to align with lspcon detection failure on some devices.
v4: Add HDR proprty in late_register to handle lspcon detection,
as suggested by Ville.
v5: Init Lspcon only if advertized from BIOS.
v6: Added a Todo to plan a cleanup later, added Ville's RB.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-4-uma.shankar@intel.com
Gen9 hardware supports HDMI2.0 through LSPCON chips.
Extending HDR support for MCA LSPCON based GEN9 devices.
SOC will drive LSPCON as DP and send HDR metadata as standard
DP SDP packets. LSPCON will be set to operate in PCON mode,
will receive the metadata and create Dynamic Range and
Mastering Infoframe (DRM packets) and send it to HDR capable
HDMI sink devices.
v2: Re-used hsw infoframe write implementation for HDR metadata
for LSPCON as per Ville's suggestion.
v3: Addressed Jani Nikula's review comments.
v4: Addressed Ville's review comments, removed redundant wrapper
and checks, passed arguments instead of hardcodings.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-3-uma.shankar@intel.com
LSPCON firmware exposes HDR capability through LPCON_CAPABILITIES
DPCD register. LSPCON implementations capable of supporting
HDR set HDR_CAPABILITY bit in LSPCON_CAPABILITIES to 1. This patch
reads the same, detects the HDR capability and adds this to
intel_lspcon struct.
v2: Addressed Jani Nikula's review comment and fixed the HDR
capability detection logic
v3: Deferred HDR detection from lspcon_init (Ville)
v4: Addressed Ville's minor review comments, added his RB.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-2-uma.shankar@intel.com
Add the calculations to set plane selective fetch registers depending
in the value of the area damaged.
It is still using the whole plane area as damaged but that will change
in next patches.
v2:
- fixed new_plane_state->uapi.dst.y2 typo in
intel_psr2_sel_fetch_update()
- do not shifthing new_plane_state->uapi.dst only src is in 16.16 format
BSpec: 55229
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130125750.17820-1-jose.souza@intel.com
