From Ard:
"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.
So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."
Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add function to identify which MPCC is providing input to a specified OPP
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC should only be acquired per OPP. Therefore, DSC should only
be acquired for the top_pipe when ODM is enabled.
Not doing this check may lead to acquiring more DSC's than needed
when doing MPO + ODM Combine.
[HOW]
Only acquire DSC if pipe is top_pipe.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FP2 programming not happening when topology changes occur with multiple
displays.
[How]
Ensure FP2 is programmed whenever global sync changes occur but wait for
VACTIVE first to avoid underflow.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HUBP blanking sequence on DCN30 requires us to check if HUBP is in blank
and also toggle HUBP_DISABLE, which should instead be called
HUBP_SOFT_RESET for what it does in HW.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FP2 is not double buffered and must wait for VACTIVE
before programming.
[How]
Only update when there is a full update we should
change FP2 to avoid delay every flip.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
race condition of programming FP2 wrt pipe locking
and vactive state can cause underflow/black screen
[How]
Enforce the FP2 is only programmed during vactive,
and unlock pipe soon afterwards.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
some DP_SEC register defs and masks are missing.
[How]
add the missing defs and masks.
Signed-off-by: Max Tseng <chuan-yu.tseng@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DSCL memory blocks should be powered down when they're not in use.
This will reduce power consumption.
[How]
1. Write to DSCL_MEM_PWR_FORCE to put memory to shutdown when DSCL is not
used.
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The MPCC may change and request data when the pipes are switching from 2
to 1 or 1 to 2. During the switch there is a possibility of underflow
and flicker/missing data.
[How]
During VBlank the MPCC won't request data. The trick is to delay and
wait on VBlank, ONLY when pipes are either turning on or off, right
before MPCC is reset for the pipes.
Signed-off-by: Tashfique Abdullah <tabdullah@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We don't want GSL to be enabled when only updating
plane address
[How]
Only check other pipes for immediate flip if GSL is
already enabled
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.
[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to make sure all immediate flips are completed before locking
the pipes, but not pipes that are not flip immediate as they will be
locked by the OTG
[How]
Skip non flip immediate pipes when checking for flip pending.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the freesync power optimization increasing vtotal, the driver
believes that MPO is supported. MPO is turned on. Freesync then
exits, MPO can no longer be supported and immediate flip fails. This
causes corruption on the panel.
[How]
Avoid the freesync optimization when doing validation so in the case
freesync exits, driver can still support the configuration.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoids confusion in configurations.
v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Prior commit "Blank HUBP during pixel data blank for DCN30"
missed the call to set_disp_pattern_generator from
set_crtc_test_pattern, which re-exposed the issue for which
we initially blocked active-only p-state switching.
[How]
- remove dcn30_blank_pixel_data, set dcn30 back to dcn20 version
- new hwss funciton set_disp_pattern_generator
- dcn20 version just calls opp_set_disp_pattern_generator
- dcn30 version implements the HUBP blank
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When checking if we want to disable GSL or not,
we should reset flip_immediate to be the flip type
of the topmost plane before looping through the
other planes.
[How]
Set flip_immediate to be the flip type of the topmost
plane before looping through the other planes.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling PIP in Heaven, the PIP planes are VSYNC
flip and is also the top-most pipe. In this case GSL
will be disabled because we only check immediate flip
for the top pipe. However, the desktop planes are still
flip immediate so we should at least keep GSL on until
the full update.
[How]
Check each pipe in the tree to see if any planes
are flip immediate. Maintain the GSL lock if yes,
and take it down after when unlocking if any planes
are flipping VSYNC. Keeping GSL on with VSYNC +
flip immediate planes causes corruption.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should leave GSL if we're not doing immediate flip no matter if
we're doing pipe split or not
[How]
Check for updating GSL state whenever we're not doing
immediate flip
v2: Squash in build fix (Alex)
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow counter increases in AGM when performing some mode switches due
to timing sync, which is a known hardware issue.
[How]
Temporarily raise DPG height during timing sync so that underflow is not
reported.
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.
[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Enable ODM Combine + Fullscreen MPO on DCN2.1
For lower power consumption in video use cases.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Create a separate dcn21_fast_validate_bw function for dcn21.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When forcing 3D mode in DAL, we set the right address to be the same as the
left address. We need to do the same for the meta addresses.
[How]
Program right meta to be same as left meta.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should be programmed with timing rather than with odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.
This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Formula uses kHz in their formula while our driver operates with Hz.
[How]
Divide audio rate by 1000 on the initial variable that is entered into formula.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We dont's turn off backlight before power off eDP (VDD),
which is a violation of eDP specs.
[How]
Power off eDP backlight before power off eDP
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
"Copy GSL groups when committing a new context" patch was accidentally
removed during a refactor
Patch: 21ffcc94d5 ("drm/amd/display: Copy GSL groups when committing a new context")
[How]
Re add it
Fixes: b6e881c947 ("drm/amd/display: update navi to use new surface programming behaviour")
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Recent characterization shows increased stutter latencies on some SKUs,
leading to underflow.
[how]
Update SOC params to account for this worst case latency.
Signed-off-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows us to reuse these on different asics.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function set_mst_bandwidth is poorly name since it isn't clear what
it does, and it also does not reflect any part of the allocation sequence
described in the DP spec.
[How]
Rename the function set_mst_bandwidth to set_throttled_vcp_size.
Signed-off-by: George Shen <george.shen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When pipe locks are being taken we wait for flip pending to clear first.
In some cases the pipe mapping is changed and the pending we're checking
for will never clear.
[How]
Don't check disabled pipes for flip pending.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If plane has changed, dcn20_detect_pipe_changes doesn't update dc_plane_state->update_flags, and the following dcn20_program_pipe can't reprogram hubp correctly.
[How]
Add a new flags bit "plane_changed" in pipe_ctx->update_flags.If old plane isn’t identical to new plane, this bit will be set and guide “dcn20_program_pipe” to programing HUBP correctly.
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dpcs reg are missing for dcn3 link encoder regs list, so add them.
Also remove
DPCSTX_DEBUG_CONFIG and RDPCSTX_DEBUG_CONFIG as they are unused and
cause compile errors for dcn3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This field is not defined for DCN3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Current pipe merge and split logic only supports cases where new
dc_state is allocated and relies on dc->current_state to gather
information from previous dc_state.
Calls to validate_bandwidth on UPDATE_TYPE_MED would cause an issue
because there is no new dc_state allocated, and data in
dc->current_state would be overwritten during pipe merge.
[how]
Only allow validate_bandwidth when new dc_state space is created.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Place the cursor in the center of screen between two pipes then
adjusting the viewport but cursour doesn't update cause DFPstate hang.
[How]
If viewport changed, update cursor as well.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reading for DP alt registers return incorrect values due to LE_SF
definition missing.
[How]
Define correct LE_SF or DP alt registers.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds ARM64 support into the DCN. This mainly enables support
for Navi graphics cards. The dcn10 changes haven't been tested,
since I don't have the relevant hardware available, but there
is no way to conditionally disable them, so I've done them anyway.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFP_KERNEL may and will sleep, and this is being executed in
a non-preemptible context; this will mess things up since it's
called inbetween DC_FP_START/END, and rescheduling will result
in the DC_FP_END later being called in a different context (or
just crashing if any floating point/vector registers/instructions
are used after the call is resumed in a different context).
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Register definitions are asic-specific, so functions that use registers of
a particular asic should be static, to be exposed in asic-specific function
pointer structures.
[How]
- make register-definition-using functions static
- make some functions non-static, for future use
- remove duplicate function definition
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The only usage of dcn20_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During SetPathMode and UpdatePlanes, the plane state can be null. We default
to linear swizzle mode when plane state is null. This resulted in bandwidth
validation failing when trying to set 8K60 mode (which previously passed validation
during rebuild timing list).
[How]
Change the default swizzle mode from linear to 4kb_s and update pitch accordingly.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
