[Why]
We defer clock updates to after pipes have been programmed. In
some instances we use DPPCLK that have been previously set to be
"unused". This results in a brief window of time where underflow
could occur.
[How]
During prepare bandwidth allow rn_update_clocks_update_dpp_dto
to check each instance and compare previous clock to new clock.
If new clock is higher than previous clock, program DPPDTO.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit latency
being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Virtual signals were previously counted as a workaround to S0i2 hang
which is fixed on Renoir. This blocks S0i3 diags testing.
[HOW]
Stop counting virtual signals as S0i2 hang is fixed on Renoir.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
there is some garbage showing up during reboot test.
Reason:
SMU might handle display driver msg defered and driver will send
next msg to SMU after 10ms timeout, once SMU FW handle previous msg,
parameters are changed to next one, which result in a wrong value be programmed.
[How]
Extend timeout to 2s so SMU will have enough time to handle driver msg.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit
latency being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Without additional HostVM Latency, Renoir takes 2us longer to exit
self-refresh. This causes underflow in certain cases.
[How]
Add table for Renoir with updated sr exit latencies for WM set A.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While booting into OS, driver updates DPP/DISP CLKs.
But init clock value is zero which is invalid.
[How]
Get current clocks value to update init clocks.
To avoid underflow.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After removing added latency for HostVM by default, DDR4 sr exit
latencies were no longer large enough for some panels and caused
underflow.
[How]
Add 1us to sr enter/exit watermark.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Blue screen when PNP with multiple monitor or hotplug external monitor when playing video
due to dpp dto isn't programmed properly.
If lower dpp clock, dpp dto need to be programmed first, and actual dpp clk not avalable yet.
[How]
set dpp dto as per request clk for lower case before dpp clk update, and after dpp clk updated
set dpp dto again with actual dpp clk.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Currently if VBIOSSMC_Result_UnknownCmd is returned as result of smu msg
there is no way to know. Put 1 in param so if 1 is returned, this unknown case is handled.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dpp dto phase and modulo are programmed with actual dpp global clk
and pipe clk. Need to use actual dpp clk to prgoram dpp dto modulo
to get more accuracy ratio.
[How]
assign actual dpp clk to dccg for dpp modulo programming.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Actual dpp/disp clock PMFW set are always equal or more than requested.
Need to cache the actual clock for debugging purpose.
[How]
Add actuall dpp/disp clk in clock manager and save it when set clocks.
Add an ASSERT in case of actual clock less than requested.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Program modulo with ref dpp clk Mhz/10.
Program phase with pipe dpp clk Mhz /10.
DMUB FW could use these value to determine optimization clk
for PSR power saving.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Currently disable 48mhz debug option only disables on boot.
Need to put option check in update_clocks as well to make it
affect more areas.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 78fe9f6394 ("drm/amd/display: Remove DISPCLK Limit Floor for Certain SMU Versions")
added a call to rn_vbios_smu_get_smu_version() to set clk_mgr->smu_ver.
That field is initialized prior to the if-statement, already.
Fixes: 78fe9f6394 (drm/amd/display: Remove DISPCLK Limit Floor for Certain SMU Versions)
Signed-off-by: Dirk Gouders <dirk@gouders.net>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Sung Lee <sung.lee@amd.com>
Cc: Yongqiang Sun <yongqiang.sun@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the load processes for Renoir, our display code needs to retrieve
the SMU clock and voltage table, however, this operation can fail which
means that we have to check this scenario. Currently, we are not
handling this case properly and as a result, we have seen the following
dmesg log during the boot:
RIP: 0010:rn_clk_mgr_construct+0x129/0x3d0 [amdgpu]
...
Call Trace:
dc_clk_mgr_create+0x16a/0x1b0 [amdgpu]
dc_create+0x231/0x760 [amdgpu]
This commit fixes this issue by checking the return status retrieved
from the clock table before try to populate any bandwidth.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
update_clocks might not be called on headless adapters. This means
DISPLAY_OFF may not be sent in headless cases.
[HOW]
If hardware is powered down on boot because it is headless (mode set
does not happen on that adapter) also send DISPLAY_OFF notification.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when ppt disabled, the watermark doesn't get fine tune causing
underflow.
[How]
It is a temporary solution to reduce sr_xxx_time by 3 us when ppt
disable.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we don't explicitly send a request for a minimum PHYCLK, and
we hope that the dependencies other clocks have will raise PHYCLK when
needed.
[How]
- new clk_mgr function to keep track of PHYCLK requirements
- request maximum requirement across all links
- remove PHYCLK from clock state comparator, as it doesn't come from DML
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU may return error code to driver, but driver only check if response
is OK.
[How]
Check SMU response instead of reg_wait, assert in case of reponse isn't
OK.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We try to to change new_clocks->dppclk_khz to 100000 when
new_clocks->dppclk_khz is 0
[How]
Don't change new_clocks->dppclk_khz value when new_clocks->dppclk_khz is
0
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In cases where a clock table is malformed such that fclk entries have
frequencies but not voltages listed, we don't catch the error and set
clocks to 0 instead of using hardcoded values as we should.
[HOW]
Add check for clock tables fclk entry's voltage as well
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[WHY]
SMU FW previously had an issue with lowering display clock to below 100
MHz, and a workaround was put in to limit it. Newest SMU FW does not
have this issue, and no longer needs the 100MHz cap.
[HOW]
Remove the 100MHz cap based on the SMU FW version.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some structures and functions meant only to be used in the
scope of that single rn_clk_mgr c file.
[How]
Make structs and funcs static if only meant to be used within
rn_clk_mgr
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Having watermark ranges saved inside clk_mgr to be
available for debug at all times would be useful.
Add it to the clk_mgr_internal struct for reference.
Only populated for Renoir, unused for other asics.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
48mhz turn off feature does not work on HDMI and DVI, but the feauture
was only blocked on HDMI, this change will apply the same wa on DVI
[HOW]
Apply workaround for all TMDS signal types (HDMI, DVI single/dual link)
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A corner case currently exists where DPP DTO is lowered before
pipes are updated to a higher viewport. This causes underflow
as the DPPCLK is too low for the current viewport.
[How]
Only lower DPP DTO when it is safe to lower, or if
the newer clocks are higher than the current ones.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems always request passive flip on RN due to incorrect compare
clock state to determine optization.
[How]
Instead of calling memcmp, compare clock state member to determine the
condition.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized sr latency numbers, for lpddr4
[How]
change the sr laency in the lpddr4 wm table to the new latency
number
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers, for lpddr4
[How]
change the p-state laency in the lpddr4 wm table to the new latency
number
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before was using HW counter value to determine the dprefclk. Which
take into account ss, but has large variation, not good enough for
generating audio dto. Also, the bios parser code to get the ss
percentage was not working.
[How]
After this change, dprefclk is hard coded, same as on RV. We don't
expect this to change on Renoir. Modified bios parser code to get
the right ss percentage.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new sr and pstate latencies are optimized for the case when we are not
using lpddr4 memory
[How]
have two different wm tables, one for the lpddr case and one for
non lpddr case
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When video_memory_type bw_params->vram_type
is assigned, wedistinguish between Ddr4MemType and LpDdr4MemType.
Because of this we will never report that we are using
LpDdr4MemType and never re-purpose WM set D
[How]
populate bios integrated info for renoir by adding the
revision number for renoir and use that integrated info
table instead of of asic_id to get the vram type
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
First, to make code more consistent
Second, to get rid of those scenario where we create a second
local pointer to dc when it's already passed in.
[How]
Rename core_dc to dc
Remove duplicate local pointers to dc
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers.
[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
* Clk Mgr DTO update point did not cover all needed updates, as it included a
check for plane_state which does not exist yet when the updater is called on
driver startup
* This resulted in another update path in the pipe programming sequence, based
on a dppclk update flag
* However, this alternate path allowed for stray DTO updates, some of which would
occur in the wrong order during dppclk lowering and cause underflow
[How]
* Remove plane_state check and use of plane_res.dpp->inst, getting rid
of sequence dependencies (this results in extra dto programming for unused
pipes but that doesn't cause issues and is a small cost)
* Allow DTOs to be updated even if global clock is equal, to account for
edge case exposed by diags tests
* Remove update_dpp_dto call in pipe programming sequence (leave update to
dppclk_control there, as that update is necessary and shouldn't occur in clk
mgr)
* Remove call to optimize_bandwidth when committing state, as it is not needed
and resulted in sporadic underflows even with other fixes in place
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU does not keep the wm table across S3, S4, need to re-send
the table. Also defer sending the cable to after DCN bave initialized
[How]
Send table at end of init hw
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This value will be needed by dml and therefore should be externally
accessible.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System hang during S0i3 if DP only connected due to clk is disabled when
doing link training.
During S0i3, clk is disabled while the clk state is updated when ini_hw
called, and at the moment clk is still disabled which indicating a wrong
state for next time trying to enable clk.
[How]
Add an unknown state and initialize it during int_hw, make sure enable clk
command be sent to smu.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use requested_dispclk_khz / 1000 directly
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU fixed this issue after version 0x370c00
[How]
enable smu send message to set dcfclk after smu version 0x370c00
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Should always MP0_BASE for any register definition from MP per-IP header files.
I belive the reason the linux version of MP1_BASE works is The 0th element of the 0th table
of that is identical to the corrisponding value of MP0_BASE in the renoir offset header file.
The reason we should only use MP0_BASE is There is only one set of per-IP headers MP
that includes all register definitions related to SMU IP block. This IP includes MP0, MP1, MP2
and an ecryption engine that can be used only by MP0. As a result all register definitions from
MP file should be based only on MP0_BASE data.
[How]
Change MP1_BASE to MP0_BASE
Signed-off-by: joseph gravenor <joseph.gravenor@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Handle the case where we don't get a valid table. Also fixes compiler
warning for variable potentially used before assignment.
[How]
If the entire table has no valid fclk, reject the table and use our own
hard code.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
dprefclk is improperly read due to incorrect units used.
Causes an audio clock to be improperly set, making audio
non-functional and videos play back too fast
[HOW]
Scale dprefclk value from MHz to KHz (multiply by 1000)
to ensure that dprefclk_khz is in correct units
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Doing this allows us to split it for diffrent asics. This design will
be helpful for future Asciis.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously SMU was giving us 0s for the clock table. Now they have valid
clock table. We should use theirs. Also, need to send SMU watermark
ranges for selecting optimal watermarks.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
