For cases where there is a mismatch in ARMv8.2-LVA support between CPUs
we have to be careful in allowing secondary CPUs to boot if 52-bit
virtual addresses have already been enabled on the boot CPU.
This patch adds code to the secondary startup path. If the boot CPU has
enabled 52-bit VAs then ID_AA64MMFR2_EL1 is checked to see if the
secondary can also enable 52-bit support. If not, the secondary is
prevented from booting and an error message is displayed indicating why.
Technically this patch could be implemented using the cpufeature code
when considering 52-bit userspace support. However, we employ low level
checks here as the cpufeature code won't be able to run if we have
mismatched 52-bit kernel va support.
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Enabling 52-bit VAs on arm64 requires that the PGD table expands from 64
entries (for the 48-bit case) to 1024 entries. This quantity,
PTRS_PER_PGD is used as follows to compute which PGD entry corresponds
to a given virtual address, addr:
pgd_index(addr) -> (addr >> PGDIR_SHIFT) & (PTRS_PER_PGD - 1)
Userspace addresses are prefixed by 0's, so for a 48-bit userspace
address, uva, the following is true:
(uva >> PGDIR_SHIFT) & (1024 - 1) == (uva >> PGDIR_SHIFT) & (64 - 1)
In other words, a 48-bit userspace address will have the same pgd_index
when using PTRS_PER_PGD = 64 and 1024.
Kernel addresses are prefixed by 1's so, given a 48-bit kernel address,
kva, we have the following inequality:
(kva >> PGDIR_SHIFT) & (1024 - 1) != (kva >> PGDIR_SHIFT) & (64 - 1)
In other words a 48-bit kernel virtual address will have a different
pgd_index when using PTRS_PER_PGD = 64 and 1024.
If, however, we note that:
kva = 0xFFFF << 48 + lower (where lower[63:48] == 0b)
and, PGDIR_SHIFT = 42 (as we are dealing with 64KB PAGE_SIZE)
We can consider:
(kva >> PGDIR_SHIFT) & (1024 - 1) - (kva >> PGDIR_SHIFT) & (64 - 1)
= (0xFFFF << 6) & 0x3FF - (0xFFFF << 6) & 0x3F // "lower" cancels out
= 0x3C0
In other words, one can switch PTRS_PER_PGD to the 52-bit value globally
provided that they increment ttbr1_el1 by 0x3C0 * 8 = 0x1E00 bytes when
running with 48-bit kernel VAs (TCR_EL1.T1SZ = 16).
For kernel configuration where 52-bit userspace VAs are possible, this
patch offsets ttbr1_el1 and sets PTRS_PER_PGD corresponding to the
52-bit value.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Steve Capper <steve.capper@arm.com>
[will: added comment to TTBR1_BADDR_4852_OFFSET calculation]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Those image head's flags will be used later by kexec_file loader.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that deliberate writes to swapper_pg_dir are made via the fixmap, we
can defend against errant writes by moving it into the rodata section.
Since tramp_pg_dir and reserved_ttbr0 must be at a fixed offset from
swapper_pg_dir, and are not modified at runtime, these are also moved
into the rodata section. Likewise, idmap_pg_dir is not modified at
runtime, and is moved into rodata.
Signed-off-by: Jun Yao <yaojun8558363@gmail.com>
Reviewed-by: James Morse <james.morse@arm.com>
[Mark: simplify linker script, commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since the address of swapper_pg_dir is fixed for a given kernel image,
it is an attractive target for manipulation via an arbitrary write. To
mitigate this we'd like to make it read-only by moving it into the
rodata section.
We require that swapper_pg_dir is at a fixed offset from tramp_pg_dir
and reserved_ttbr0, so these will also need to move into rodata.
However, swapper_pg_dir is allocated along with some transient page
tables used for boot which we do not want to move into rodata.
As a step towards this, this patch separates the boot-time page tables
into a new init_pg_dir, and reduces swapper_pg_dir to the single page it
needs to be. This allows us to retain the relationship between
swapper_pg_dir, tramp_pg_dir, and swapper_pg_dir, while cleanly
separating these from the boot-time page tables.
The init_pg_dir holds all of the pgd/pud/pmd/pte levels needed during
boot, and all of these levels will be freed when we switch to the
swapper_pg_dir, which is initialized by the existing code in
paging_init(). Since we start off on the init_pg_dir, we no longer need
to allocate a transient page table in paging_init() in order to ensure
that swapper_pg_dir isn't live while we initialize it.
There should be no functional change as a result of this patch.
Signed-off-by: Jun Yao <yaojun8558363@gmail.com>
Reviewed-by: James Morse <james.morse@arm.com>
[Mark: place init_pg_dir after BSS, fold mm changes, commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In subsequent patches we'll use a transient pgd during the primary cpu's
boot process. To make this work while allowing secondary cpus to use the
swapper_pg_dir, we need to pass the relevant TTBR1 pgd as a parameter
to __enable_mmu().
This patch updates __enable__mmu() to take this as a parameter, updating
callsites to pass swapper_pg_dir for now.
There should be no functional change as a result of this patch.
Signed-off-by: Jun Yao <yaojun8558363@gmail.com>
Reviewed-by: James Morse <james.morse@arm.com>
[Mark: simplify assembly, clarify commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We don't currently limit guest accesses to the LOR registers, which we
neither virtualize nor context-switch. As such, guests are provided with
unusable information/controls, and are not isolated from each other (or
the host).
To prevent these issues, we can trap register accesses and present the
illusion LORegions are unssupported by the CPU. To do this, we mask
ID_AA64MMFR1.LO, and set HCR_EL2.TLOR to trap accesses to the following
registers:
* LORC_EL1
* LOREA_EL1
* LORID_EL1
* LORN_EL1
* LORSA_EL1
... when trapped, we inject an UNDEFINED exception to EL1, simulating
their non-existence.
As noted in D7.2.67, when no LORegions are implemented, LoadLOAcquire
and StoreLORelease must behave as LoadAcquire and StoreRelease
respectively. We can ensure this by clearing LORC_EL1.EN when a CPU's
EL2 is first initialized, as the host kernel will not modify this.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Vladimir Murzin <vladimir.murzin@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The identity map is mapped as both writeable and executable by the
SWAPPER_MM_MMUFLAGS and this is relied upon by the kpti code to manage
a synchronisation flag. Update the .pushsection flags to reflect the
actual mapping attributes.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
pte_to_phys lives in assembler.h and takes its destination register as
the first argument. Move phys_to_pte out of head.S to sit with its
counterpart and rejig it to follow the same calling convention.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since AArch64 assembly instructions take the destination register as
their first operand, do the same thing for the phys_to_ttbr macro.
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The ARM architecture defines the memory locations that are permitted
to be accessed as the result of a speculative instruction fetch from
an exception level for which all stages of translation are disabled.
Specifically, the core is permitted to speculatively fetch from the
4KB region containing the current program counter 4K and next 4K.
When translation is changed from enabled to disabled for the running
exception level (SCTLR_ELn[M] changed from a value of 1 to 0), the
Falkor core may errantly speculatively access memory locations outside
of the 4KB region permitted by the architecture. The errant memory
access may lead to one of the following unexpected behaviors.
1) A System Error Interrupt (SEI) being raised by the Falkor core due
to the errant memory access attempting to access a region of memory
that is protected by a slave-side memory protection unit.
2) Unpredictable device behavior due to a speculative read from device
memory. This behavior may only occur if the instruction cache is
disabled prior to or coincident with translation being changed from
enabled to disabled.
The conditions leading to this erratum will not occur when either of the
following occur:
1) A higher exception level disables translation of a lower exception level
(e.g. EL2 changing SCTLR_EL1[M] from a value of 1 to 0).
2) An exception level disabling its stage-1 translation if its stage-2
translation is enabled (e.g. EL1 changing SCTLR_EL1[M] from a value of 1
to 0 when HCR_EL2[VM] has a value of 1).
To avoid the errant behavior, software must execute an ISB immediately
prior to executing the MSR that will change SCTLR_ELn[M] from 1 to 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
__cpu_setup() configures SCTLR_EL1 using some hard coded hex masks,
and el2_setup() duplicates some this when setting RES1 bits.
Lets make this the same as KVM's hyp_init, which uses named bits.
First, we add definitions for all the SCTLR_EL{1,2} bits, the RES{1,0}
bits, and those we want to set or clear.
Add a build_bug checks to ensures all bits are either set or clear.
This means we don't need to preserve endian-ness configuration
generated elsewhere.
Finally, move the head.S and proc.S users of these hard-coded masks
over to the macro versions.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently the early assembler page table code assumes that precisely
1xpgd, 1xpud, 1xpmd are sufficient to represent the early kernel text
mappings.
Unfortunately this is rarely the case when running with a 16KB granule,
and we also run into limits with 4KB granule when building much larger
kernels.
This patch re-writes the early page table logic to compute indices of
mappings for each level of page table, and if multiple indices are
required, the next-level page table is scaled up accordingly.
Also the required size of the swapper_pg_dir is computed at link time
to cover the mapping [KIMAGE_ADDR + VOFFSET, _end]. When KASLR is
enabled, an extra page is set aside for each level that may require extra
entries at runtime.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently, when using VA_BITS < 48, if the ID map text happens to be
placed in physical memory above VA_BITS, we increase the VA size (up to
48) and create a new table level, in order to map in the ID map text.
This is okay because the system always supports 48 bits of VA.
This patch extends the code such that if the system supports 52 bits of
VA, and the ID map text is placed that high up, then we increase the VA
size accordingly, up to 52.
One difference from the current implementation is that so far the
condition of VA_BITS < 48 has meant that the top level table is always
"full", with the maximum number of entries, and an extra table level is
always needed. Now, when VA_BITS = 48 (and using 64k pages), the top
level table is not full, and we simply need to increase the number of
entries in it, instead of creating a new table level.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: reduce arguments to __create_hyp_mappings()]
[catalin.marinas@arm.com: reworked/renamed __cpu_uses_extended_idmap_level()]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The top 4 bits of a 52-bit physical address are positioned at bits
12..15 of a page table entry. Introduce macros to convert between a
physical address and its placement in a table entry, and change all
macros/functions that access PTEs to use them.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: some long lines wrapped]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The top 4 bits of a 52-bit physical address are positioned at bits
12..15 in page table entries. Introduce a macro to move the bits there,
and change the early ID map and swapper table setup code to use it.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: additional comments for clarification]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The top 4 bits of a 52-bit physical address are positioned at bits 2..5
in the TTBR registers. Introduce a couple of macros to move the bits
there, and change all TTBR writers to use them.
Leave TTBR0 PAN code unchanged, to avoid complicating it. A system with
52-bit PA will have PAN anyway (because it's ARMv8.1 or later), and a
system without 52-bit PA can only use up to 48-bit PAs. A later patch in
this series will add a kconfig dependency to ensure PAN is configured.
In addition, when using 52-bit PA there is a special alignment
requirement on the top-level table. We don't currently have any VA_BITS
configuration that would violate the requirement, but one could be added
in the future, so add a compile-time BUG_ON to check for it.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: added TTBR_BADD_MASK_52 comment]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
To enable the kernel to use SVE, SVE traps from EL1 to EL2 must be
disabled. To take maximum advantage of the hardware, the full
available vector length also needs to be enabled for EL1 by
programming ZCR_EL2.LEN. (The kernel will program ZCR_EL1.LEN as
required, but this cannot override the limit set by ZCR_EL2.)
This patch makes the appropriate changes to the EL2 early setup
code.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When booting at EL2, ensure that we permit the EL1 host to sample
physical addresses and physical counter values using SPE.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When the kernel is entered at EL2 on an ARMv8.0 system, we construct
the EL1 pstate and make sure this uses the the EL1 stack pointer
(we perform an exception return to EL1h).
But if the kernel is either entered at EL1 or stays at EL2 (because
we're on a VHE-capable system), we fail to set SPsel, and use whatever
stack selection the higher exception level has choosen for us.
Let's not take any chance, and make sure that SPsel is set to one
before we decide the mode we're going to run in.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- VMAP_STACK support, allowing the kernel stacks to be allocated in
the vmalloc space with a guard page for trapping stack overflows. One
of the patches introduces THREAD_ALIGN and changes the generic
alloc_thread_stack_node() to use this instead of THREAD_SIZE (no
functional change for other architectures)
- Contiguous PTE hugetlb support re-enabled (after being reverted a
couple of times). We now have the semantics agreed in the generic mm
layer together with API improvements so that the architecture code can
detect between contiguous and non-contiguous huge PTEs
- Initial support for persistent memory on ARM: DC CVAP instruction
exposed to user space (HWCAP) and the in-kernel pmem API implemented
- raid6 improvements for arm64: faster algorithm for the delta syndrome
and implementation of the recovery routines using Neon
- FP/SIMD refactoring and removal of support for Neon in interrupt
context. This is in preparation for full SVE support
- PTE accessors converted from inline asm to cmpxchg so that we can
use LSE atomics if available (ARMv8.1)
- Perf support for Cortex-A35 and A73
- Non-urgent fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=vd0/
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- VMAP_STACK support, allowing the kernel stacks to be allocated in the
vmalloc space with a guard page for trapping stack overflows. One of
the patches introduces THREAD_ALIGN and changes the generic
alloc_thread_stack_node() to use this instead of THREAD_SIZE (no
functional change for other architectures)
- Contiguous PTE hugetlb support re-enabled (after being reverted a
couple of times). We now have the semantics agreed in the generic mm
layer together with API improvements so that the architecture code
can detect between contiguous and non-contiguous huge PTEs
- Initial support for persistent memory on ARM: DC CVAP instruction
exposed to user space (HWCAP) and the in-kernel pmem API implemented
- raid6 improvements for arm64: faster algorithm for the delta syndrome
and implementation of the recovery routines using Neon
- FP/SIMD refactoring and removal of support for Neon in interrupt
context. This is in preparation for full SVE support
- PTE accessors converted from inline asm to cmpxchg so that we can use
LSE atomics if available (ARMv8.1)
- Perf support for Cortex-A35 and A73
- Non-urgent fixes and cleanups
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (75 commits)
arm64: cleanup {COMPAT_,}SET_PERSONALITY() macro
arm64: introduce separated bits for mm_context_t flags
arm64: hugetlb: Cleanup setup_hugepagesz
arm64: Re-enable support for contiguous hugepages
arm64: hugetlb: Override set_huge_swap_pte_at() to support contiguous hugepages
arm64: hugetlb: Override huge_pte_clear() to support contiguous hugepages
arm64: hugetlb: Handle swap entries in huge_pte_offset() for contiguous hugepages
arm64: hugetlb: Add break-before-make logic for contiguous entries
arm64: hugetlb: Spring clean huge pte accessors
arm64: hugetlb: Introduce pte_pgprot helper
arm64: hugetlb: set_huge_pte_at Add WARN_ON on !pte_present
arm64: kexec: have own crash_smp_send_stop() for crash dump for nonpanic cores
arm64: dma-mapping: Mark atomic_pool as __ro_after_init
arm64: dma-mapping: Do not pass data to gen_pool_set_algo()
arm64: Remove the !CONFIG_ARM64_HW_AFDBM alternative code paths
arm64: Ignore hardware dirty bit updates in ptep_set_wrprotect()
arm64: Move PTE_RDONLY bit handling out of set_pte_at()
kvm: arm64: Convert kvm_set_s2pte_readonly() from inline asm to cmpxchg()
arm64: Convert pte handling from inline asm to using (cmp)xchg
arm64: neon/efi: Make EFI fpsimd save/restore variables static
...
In the KASLR setup routine, we ensure that the early virtual mapping
of the kernel image does not cover more than a single table entry at
the level above the swapper block level, so that the assembler routines
involved in setting up this mapping can remain simple.
In this calculation we add the proposed KASLR offset to the values of
the _text and _end markers, and reject it if they would end up falling
in different swapper table sized windows.
However, when taking the addresses of _text and _end, the modulo offset
(the physical displacement modulo 2 MB) is already accounted for, and
so adding it again results in incorrect results. So disregard the modulo
offset from the calculation.
Fixes: 08cdac619c ("arm64: relocatable: deal with physically misaligned ...")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As it turns out, the unwind code is slightly broken, and probably has
been for a while. The problem is in the dumping of the exception stack,
which is intended to dump the contents of the pt_regs struct at each
level in the call stack where an exception was taken and routed to a
routine marked as __exception (which means its stack frame is right
below the pt_regs struct on the stack).
'Right below the pt_regs struct' is ill defined, though: the unwind
code assigns 'frame pointer + 0x10' to the .sp member of the stackframe
struct at each level, and dump_backtrace() happily dereferences that as
the pt_regs pointer when encountering an __exception routine. However,
the actual size of the stack frame created by this routine (which could
be one of many __exception routines we have in the kernel) is not known,
and so frame.sp is pretty useless to figure out where struct pt_regs
really is.
So it seems the only way to ensure that we can find our struct pt_regs
when walking the stack frames is to put it at a known fixed offset of
the stack frame pointer that is passed to such __exception routines.
The simplest way to do that is to put it inside pt_regs itself, which is
the main change implemented by this patch. As a bonus, doing this allows
us to get rid of a fair amount of cruft related to walking from one stack
to the other, which is especially nice since we intend to introduce yet
another stack for overflow handling once we add support for vmapped
stacks. It also fixes an inconsistency where we only add a stack frame
pointing to ELR_EL1 if we are executing from the IRQ stack but not when
we are executing from the task stack.
To consistly identify exceptions regs even in the presence of exceptions
taken from entry code, we must check whether the next frame was created
by entry text, rather than whether the current frame was crated by
exception text.
To avoid backtracing using PCs that fall in the idmap, or are controlled
by userspace, we must explcitly zero the FP and LR in startup paths, and
must ensure that the frame embedded in pt_regs is zeroed upon entry from
EL0. To avoid these NULL entries showin in the backtrace, unwind_frame()
is updated to avoid them.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[Mark: compare current frame against .entry.text, avoid bogus PCs]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
__inval_cache_range() is already the odd one out among our data cache
maintenance routines as the only remaining range-based one; as we're
going to want an invalidation routine to call from C code for the pmem
API, let's tweak the prototype and name to bring it in line with the
clean operations, and to make its relationship with __dma_inv_area()
neatly mirror that of __clean_dcache_area_poc() and __dma_clean_area().
The loop clearing the early page tables gets mildly massaged in the
process for the sake of consistency.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
After having split off the PE header, clean up the bits that remain:
use .long consistently, merge two adjacent #ifdef CONFIG_EFI blocks,
fix the offset of the PE header pointer and remove the redundant .align
that follows it.
Also, since we will be eliminating all open coded constants from the
EFI header in subsequent patches, let's replace the open coded "ARM\x64"
magic number with its .ascii equivalent.
No changes to the resulting binary image are intended.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation of yet another round of modifications to the PE/COFF
header, macroize it and move the definition into a separate source
file.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We only need to initialise sctlr_el1 if we're installing an EL2 stub, so
we may as well defer this until we're doing so. Similarly, we can defer
intialising CPTR_EL2 until then, as we do not access any trapped
functionality as part of el2_setup.
This patch modified el2_setup accordingly, allowing us to remove a
branch and simplify the code flow.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The early el2_setup code is a little convoluted, with two branches where
one would do. This makes the code more painful to read than is
necessary.
We can remove a branch and simplify the logic by moving the early return
in the booted-at-EL1 case earlier in the function. This separates it
from all the setup logic that only makes sense for EL2.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Unlike most sysreg defintiions, the GICv3 definitions don't have a SYS_
prefix, and they don't live in <asm/sysreg.h>. Additionally, some
definitions are duplicated elsewhere (e.g. in the KVM save/restore
code).
For consistency, and to make it possible to share a common definition
for these sysregs, this patch moves the definitions to <asm/sysreg.h>,
adding a SYS_ prefix, and sorting the registers per their encoding.
Existing users of the definitions are fixed up so that this change is
not problematic.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
The SPE architecture requires each exception level to enable access
to the SPE controls for the exception level below it, since additional
context-switch logic may be required to handle the buffer safely.
This patch allows EL1 (host) access to the SPE controls when entered at
EL2.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When building with debugging symbols, take the absolute path to the
vmlinux binary and add it to the special PE/COFF debug table entry.
This allows a debug EFI build to find the vmlinux binary, which is
very helpful in debugging, given that the offset where the Image is
first loaded by EFI is highly unpredictable.
On implementations of UEFI that choose to implement it, this
information is exposed via the EFI debug support table, which is a UEFI
configuration table that is accessible both by the firmware at boot time
and by the OS at runtime, and lists all PE/COFF images loaded by the
system.
The format of the NB10 Codeview entry is based on the definition used
by EDK2, which is our primary reference when it comes to the use of
PE/COFF in the context of UEFI firmware.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: use realpath instead of shell invocation, as discussed on list]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some places in the kernel open-code sequences using ADRP for a symbol
another instruction using a :lo12: relocation for that same symbol.
These sequences are easy to get wrong, and more painful to read than is
necessary. For these reasons, it is preferable to use the
{adr,ldr,str}_l macros for these cases.
This patch makes use of adr_l these in head.S, removing an open-coded
sequence using adrp.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In commit 23c8a500c2 ("arm64: kernel: use ordinary return/argument
register for el2_setup()"), we stopped using w20 as a global stash of
the boot mode flag, and instead pass this around in w0 as a function
parameter.
Unfortunately, we missed a couple of comments, which still refer to the
old convention of using w20/x20.
This patch fixes up the comments to describe the code as it currently
works.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Bit positions of CNTHCTL_EL2 are changing depending on HCR_EL2.E2H bit.
EL1PCEN and EL1PCTEN are 1st and 0th bits when E2H is not set, but they
are 11th and 10th bits respectively when E2H is set. Current code is
unintentionally setting wrong bits to CNTHCTL_EL2 with E2H set.
In fact, we don't need to set those two bits, which allow EL1 and EL0 to
access physical timer and counter respectively, if E2H and TGE are set
for the host kernel. They will be configured later as necessary. First,
we don't need to configure those bits for EL1, since the host kernel
runs in EL2. It is a hypervisor's responsibility to configure them
before entering a VM, which runs in EL0 and EL1. Second, EL0 accesses
are configured in the later stage of boot process.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the uaccess macros/functions to disable access to user
space by setting TTBR0_EL1 to a reserved zeroed page. Since the value
written to TTBR0_EL1 must be a physical address, for simplicity this
patch introduces a reserved_ttbr0 page at a constant offset from
swapper_pg_dir. The uaccess_disable code uses the ttbr1_el1 value
adjusted by the reserved_ttbr0 offset.
Enabling access to user is done by restoring TTBR0_EL1 with the value
from the struct thread_info ttbr0 variable. Interrupts must be disabled
during the uaccess_ttbr0_enable code to ensure the atomicity of the
thread_info.ttbr0 read and TTBR0_EL1 write. This patch also moves the
get_thread_info asm macro from entry.S to assembler.h for reuse in the
uaccess_ttbr0_* macros.
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves arm64's struct thread_info from the task stack into
task_struct. This protects thread_info from corruption in the case of
stack overflows, and makes its address harder to determine if stack
addresses are leaked, making a number of attacks more difficult. Precise
detection and handling of overflow is left for subsequent patches.
Largely, this involves changing code to store the task_struct in sp_el0,
and acquire the thread_info from the task struct. Core code now
implements current_thread_info(), and as noted in <linux/sched.h> this
relies on offsetof(task_struct, thread_info) == 0, enforced by core
code.
This change means that the 'tsk' register used in entry.S now points to
a task_struct, rather than a thread_info as it used to. To make this
clear, the TI_* field offsets are renamed to TSK_TI_*, with asm-offsets
appropriately updated to account for the structural change.
Userspace clobbers sp_el0, and we can no longer restore this from the
stack. Instead, the current task is cached in a per-cpu variable that we
can safely access from early assembly as interrupts are disabled (and we
are thus not preemptible).
Both secondary entry and idle are updated to stash the sp and task
pointer separately.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: James Morse <james.morse@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit f436b2ac90 ("arm64: kernel: fix architected PMU registers
unconditional access") made sure we wouldn't access unimplemented
PMU registers, but also left MDCR_EL2 uninitialized in that case,
leading to trap bits being potentially left set.
Make sure we always write something in that register.
Fixes: f436b2ac90 ("arm64: kernel: fix architected PMU registers unconditional access")
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the only remaining occurrences of the use of callee saved
registers are on the primary boot path, add a comment to the code
which register is used for what.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Instead of stashing the value of the link register in x28 before setting
up the stack and calling into C code, create an ordinary PCS compatible
stack frame so that we can push the return address onto the stack.
Since exception handlers require a stack as well, assign the stack pointer
register before installing the vector table.
Note that this accounts for the difference between THREAD_START_SP and
THREAD_SIZE, given that the stack pointer is always decremented before
calling into any C code.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Keeping __PHYS_OFFSET in x24 is actually less clear than simply taking
the value of __PHYS_OFFSET using an adrp instruction in the three places
that we need it. So change that.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Using x27 for passing to __enable_mmu what is essentially the return
address makes the code look more complicated than it needs to be. So
switch to x30/lr, and update the secondary and cpu_resume call sites to
simply call __enable_mmu as an ordinary function, with a bl instruction.
This requires the callers to be covered by .idmap.text.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The KASLR processing is only used by the primary boot path, and
complements the processing that takes place in __primary_switch().
Move the two parts together, to make the code easier to understand.
Also, fix up a minor whitespace issue.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: fixed conflict with -rc3 due to lack of fd363bd417]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The function el2_setup() passes its return value in register w20, and
in the two cases where the caller actually cares about this return value,
it is passed into set_cpu_boot_mode_flag() [almost] directly, which
expects its input in w20 as well.
So there is no reason to use a 'special' callee saved register here, but
we can simply follow the PCS for return value and first argument,
respectively.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Resume from hibernate needs to clean any text executed by the kernel with
the MMU off to the PoC. Collect these functions together into the
.idmap.text section as all this code is tightly coupled and also needs
the same cleaning after resume.
Data is more complicated, secondary_holding_pen_release is written with
the MMU on, clean and invalidated, then read with the MMU off. In contrast
__boot_cpu_mode is written with the MMU off, the corresponding cache line
is invalidated, so when we read it with the MMU on we don't get stale data.
These cache maintenance operations conflict with each other if the values
are within a Cache Writeback Granule (CWG) of each other.
Collect the data into two sections .mmuoff.data.read and .mmuoff.data.write,
the linker script ensures mmuoff.data.write section is aligned to the
architectural maximum CWG of 2KB.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, x25 and x26 hold the physical addresses of idmap_pg_dir
and swapper_pg_dir, respectively, when running early boot code. But
having registers with 'global' scope in files that contain different
sections with different lifetimes, and that are called by different
CPUs at different times is a bit messy, especially since stashing the
values does not buy us anything in terms of code size or clarity.
So simply replace each reference to x25 or x26 with an adrp instruction
referring to idmap_pg_dir or swapper_pg_dir directly.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The linker routines that we rely on to produce a relocatable PIE binary
treat it as a shared ELF object in some ways, i.e., it emits symbol based
R_AARCH64_ABS64 relocations into the final binary since doing so would be
appropriate when linking a shared library that is subject to symbol
preemption. (This means that an executable can override certain symbols
that are exported by a shared library it is linked with, and that the
shared library *must* update all its internal references as well, and point
them to the version provided by the executable.)
Symbol preemption does not occur for OS hosted PIE executables, let alone
for vmlinux, and so we would prefer to get rid of these symbol based
relocations. This would allow us to simplify the relocation routines, and
to strip the .dynsym, .dynstr and .hash sections from the binary. (Note
that these are tiny, and are placed in the .init segment, but they clutter
up the vmlinux binary.)
Note that these R_AARCH64_ABS64 relocations are only emitted for absolute
references to symbols defined in the linker script, all other relocatable
quantities are covered by anonymous R_AARCH64_RELATIVE relocations that
simply list the offsets to all 64-bit values in the binary that need to be
fixed up based on the offset between the link time and run time addresses.
Fortunately, GNU ld has a -Bsymbolic option, which is intended for shared
libraries to allow them to ignore symbol preemption, and unconditionally
bind all internal symbol references to its own definitions. So set it for
our PIE binary as well, and get rid of the asoociated sections and the
relocation code that processes them.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: fixed conflict with __dynsym_offset linker script entry]
Signed-off-by: Will Deacon <will.deacon@arm.com>
- virt_to_page/page_address optimisations
- Support for NUMA systems described using device-tree
- Support for hibernate/suspend-to-disk
- Proper support for maxcpus= command line parameter
- Detection and graceful handling of AArch64-only CPUs
- Miscellaneous cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJXNbgkAAoJELescNyEwWM0PtcIAK11xaOMmSqXz8fcTeNLw4dS
taaPWhjCYus8EhJyvTetfwk74+qVApdvKXKNKgODJXQEjeQx2brdUfbQZb31DTGT
798UYCAyEYCWkXspqi+/dpZEgUGPYH7uGOu2eDd19+PhTeX/EQSRX3fC9k0BNhvh
PN9pOgRcKAlIExZ6QYmT0g56VLtbCfFShN41mQ8HdpShl6pPJuhQ+kDDzudmRjuD
11/oYuOaVTnwbPuXn+sjOrWvMkfINHI70BAQnnBs0v+5c45mzpqEMsy0dYo2Pl2m
ar5lUFVIZggQkiqcOzqBzEgF+4gNw4LUu1DgK6cNKNMtL6k8E9zeOZMWeSVr0lg=
=bT5E
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
- virt_to_page/page_address optimisations
- support for NUMA systems described using device-tree
- support for hibernate/suspend-to-disk
- proper support for maxcpus= command line parameter
- detection and graceful handling of AArch64-only CPUs
- miscellaneous cleanups and non-critical fixes
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
arm64: do not enforce strict 16 byte alignment to stack pointer
arm64: kernel: Fix incorrect brk randomization
arm64: cpuinfo: Missing NULL terminator in compat_hwcap_str
arm64: secondary_start_kernel: Remove unnecessary barrier
arm64: Ensure pmd_present() returns false after pmd_mknotpresent()
arm64: Replace hard-coded values in the pmd/pud_bad() macros
arm64: Implement pmdp_set_access_flags() for hardware AF/DBM
arm64: Fix typo in the pmdp_huge_get_and_clear() definition
arm64: mm: remove unnecessary EXPORT_SYMBOL_GPL
arm64: always use STRICT_MM_TYPECHECKS
arm64: kvm: Fix kvm teardown for systems using the extended idmap
arm64: kaslr: increase randomization granularity
arm64: kconfig: drop CONFIG_RTC_LIB dependency
arm64: make ARCH_SUPPORTS_DEBUG_PAGEALLOC depend on !HIBERNATION
arm64: hibernate: Refuse to hibernate if the boot cpu is offline
arm64: kernel: Add support for hibernate/suspend-to-disk
PM / Hibernate: Call flush_icache_range() on pages restored in-place
arm64: Add new asm macro copy_page
arm64: Promote KERNEL_START/KERNEL_END definitions to a header file
arm64: kernel: Include _AC definition in page.h
...
KERNEL_START and KERNEL_END are useful outside head.S, move them to a
header file.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
By enabling the MMU early in cpu_resume(), the sleep_save_sp and stack can
be accessed by VA, which avoids the need to convert-addresses and clean to
PoC on the suspend path.
MMU setup is shared with the boot path, meaning the swapper_pg_dir is
restored directly: ttbr1_el1 is no longer saved/restored.
struct sleep_save_sp is removed, replacing it with a single array of
pointers.
cpu_do_{suspend,resume} could be further reduced to not restore: cpacr_el1,
mdscr_el1, tcr_el1, vbar_el1 and sctlr_el1, all of which are set by
__cpu_setup(). However these values all contain res0 bits that may be used
to enable future features.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When booting a relocatable kernel image, there is no practical reason
to refuse an image whose load address is not exactly TEXT_OFFSET bytes
above a 2 MB aligned base address, as long as the physical and virtual
misalignment with respect to the swapper block size are equal, and are
both aligned to THREAD_SIZE.
Since the virtual misalignment is under our control when we first enter
the kernel proper, we can simply choose its value to be equal to the
physical misalignment.
So treat the misalignment of the physical load address as the initial
KASLR offset, and fix up the remaining code to deal with that.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
For historical reasons, the kernel Image must be loaded into physical
memory at a 512 KB offset above a 2 MB aligned base address. The region
between the base address and the start of the kernel Image has no
significance to the kernel itself, but it is currently mapped explicitly
into the early kernel VMA range for all translation granules.
In some cases (i.e., 4 KB granule), this is unavoidable, due to the 2 MB
granularity of the early kernel mappings. However, in other cases, e.g.,
when running with larger page sizes, or in the future, with more granular
KASLR, there is no reason to map it explicitly like we do currently.
So update the logic so that the region is mapped only if that happens as
a side effect of rounding the start address of the kernel to swapper block
size, and leave it unmapped otherwise.
Since the symbol kernel_img_size now simply resolves to the memory
footprint of the kernel Image, we can drop its definition from image.h
and opencode its calculation.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When building a relocatable kernel, we currently rely on the fact that
early 64-bit literal loads need to be deferred to after the relocation
has been performed only if they involve symbol references, and not if
they involve assemble time constants. While this is not an unreasonable
assumption to make, it is better to switch to movk/movz sequences, since
these are guaranteed to be resolved at link time, simply because there are
no dynamic relocation types to describe them.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Refactor the relocation processing so that the code executes from the
ID map while accessing the relocation tables via the virtual mapping.
This way, we can use literals containing virtual addresses as before,
instead of having to use convoluted absolute expressions.
For symmetry with the secondary code path, the relocation code and the
subsequent jump to the virtual entry point are implemented in a function
called __primary_switch(), and __mmap_switched() is renamed to
__primary_switched(). Also, the call sequence in stext() is aligned with
the one in secondary_startup(), by replacing the awkward 'adr_l lr' and
'b cpu_setup' sequence with a simple branch and link.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We can simply use a relocated 64-bit literal to store the address of
__secondary_switched(), and the relocation code will ensure that it
holds the correct value at secondary entry time, as long as we make sure
that the literal is not dereferenced until after we have enabled the MMU.
So jump via a small __secondary_switch() function covered by the ID map
that performs the literal load and branch-to-register.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This unexports some symbols from head.S that are only used locally.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When using the Virtualisation Host Extensions, EL1 is not used in
the host and requires no separate configuration.
In addition, with VHE enabled, non-hyp-specific EL2 configuration
that does not need to be done early will be done anyway in
__cpu_setup via the _EL1 system register aliases. In particular,
the layout and definition of CPTR_EL2 are changed by enabling VHE
so that they resemble CPACR_EL1, so existing code to initialise
CPTR_EL2 becomes architecturally wrong in this case.
This patch simply skips the affected initialisation code in the
non-VHE case.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In head.S, the str_l macro, which takes a source register, a symbol name
and a temp register, is used to store a status value to the variable
__early_cpu_boot_status. Subsequently, the value of the temp register is
reused to invalidate any cachelines covering this variable.
However, since str_l resolves to
adrp \tmp, \sym
str \src, [\tmp, :lo12:\sym]
the temp register never actually holds the address of the variable but
only of the 4 KB window that covers it, and reusing it leads to the
wrong cacheline being invalidated. So instead, take the address
explicitly before doing the store, and reuse that value to perform
the cache invalidation.
Fixes: bb9052744f ("arm64: Handle early CPU boot failures")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Suzuki K Poulose <Suzuki.Poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Apart from the arm64/linux and EFI header data structures, there is nothing
in the .head.text section that must reside at the beginning of the Image.
So let's move it to the .init section where it belongs.
Note that this involves some minor tweaking of the EFI header, primarily
because the address of 'stext' no longer coincides with the start of the
.text section. It also requires a couple of relocated symbol references
to be slightly rewritten or their definition moved to the linker script.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The KASLR code incorrectly expects the contents of x18 to be preserved
across a call into C code, and uses it to stash the contents of SCTLR_EL1
before enabling the MMU. If the MMU needs to be disabled again to create
the randomized kernel mapping, x18 is written back to SCTLR_EL1, which is
likely to crash the system if x18 has been clobbered by kasan_early_init()
or kaslr_early_init(). So use x22 instead, which is not in use so far in
head.S
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit f80fb3a3d5 ("arm64: add support for kernel ASLR") missed a
DSB necessary to complete I-cache maintenance in the primary boot path,
and hence stale instructions may still be present in the I-cache and may
be executed until the I-cache maintenance naturally completes.
Since commit 8ec4198743 ("arm64: mm: ensure patched kernel text is
fetched from PoU"), all CPUs invalidate their I-caches after their MMU
is enabled. Prior a CPU's MMU having been enabled, arbitrary lines may
have been fetched from the PoC into I-caches. We never patch text
expected to be executed with the MMU off. Thus, it is unnecessary to
perform broadcast I-cache maintenance in the primary boot path.
This patch reduces the scope of the I-cache maintenance to the local
CPU, and adds the missing DSB with similar scope, matching prior
maintenance in the primary boot path.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesehvuel <ard.biesheuvel@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Initial page table creation reworked to avoid breaking large block
mappings (huge pages) into smaller ones. The ARM architecture requires
break-before-make in such cases to avoid TLB conflicts but that's not
always possible on live page tables
- Kernel virtual memory layout: the kernel image is no longer linked to
the bottom of the linear mapping (PAGE_OFFSET) but at the bottom of
the vmalloc space, allowing the kernel to be loaded (nearly) anywhere
in physical RAM
- Kernel ASLR: position independent kernel Image and modules being
randomly mapped in the vmalloc space with the randomness is provided
by UEFI (efi_get_random_bytes() patches merged via the arm64 tree,
acked by Matt Fleming)
- Implement relative exception tables for arm64, required by KASLR
(initial code for ARCH_HAS_RELATIVE_EXTABLE added to lib/extable.c but
actual x86 conversion to deferred to 4.7 because of the merge
dependencies)
- Support for the User Access Override feature of ARMv8.2: this allows
uaccess functions (get_user etc.) to be implemented using LDTR/STTR
instructions. Such instructions, when run by the kernel, perform
unprivileged accesses adding an extra level of protection. The
set_fs() macro is used to "upgrade" such instruction to privileged
accesses via the UAO bit
- Half-precision floating point support (part of ARMv8.2)
- Optimisations for CPUs with or without a hardware prefetcher (using
run-time code patching)
- copy_page performance improvement to deal with 128 bytes at a time
- Sanity checks on the CPU capabilities (via CPUID) to prevent
incompatible secondary CPUs from being brought up (e.g. weird
big.LITTLE configurations)
- valid_user_regs() reworked for better sanity check of the sigcontext
information (restored pstate information)
- ACPI parking protocol implementation
- CONFIG_DEBUG_RODATA enabled by default
- VDSO code marked as read-only
- DEBUG_PAGEALLOC support
- ARCH_HAS_UBSAN_SANITIZE_ALL enabled
- Erratum workaround Cavium ThunderX SoC
- set_pte_at() fix for PROT_NONE mappings
- Code clean-ups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/oS+
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Here are the main arm64 updates for 4.6. There are some relatively
intrusive changes to support KASLR, the reworking of the kernel
virtual memory layout and initial page table creation.
Summary:
- Initial page table creation reworked to avoid breaking large block
mappings (huge pages) into smaller ones. The ARM architecture
requires break-before-make in such cases to avoid TLB conflicts but
that's not always possible on live page tables
- Kernel virtual memory layout: the kernel image is no longer linked
to the bottom of the linear mapping (PAGE_OFFSET) but at the bottom
of the vmalloc space, allowing the kernel to be loaded (nearly)
anywhere in physical RAM
- Kernel ASLR: position independent kernel Image and modules being
randomly mapped in the vmalloc space with the randomness is
provided by UEFI (efi_get_random_bytes() patches merged via the
arm64 tree, acked by Matt Fleming)
- Implement relative exception tables for arm64, required by KASLR
(initial code for ARCH_HAS_RELATIVE_EXTABLE added to lib/extable.c
but actual x86 conversion to deferred to 4.7 because of the merge
dependencies)
- Support for the User Access Override feature of ARMv8.2: this
allows uaccess functions (get_user etc.) to be implemented using
LDTR/STTR instructions. Such instructions, when run by the kernel,
perform unprivileged accesses adding an extra level of protection.
The set_fs() macro is used to "upgrade" such instruction to
privileged accesses via the UAO bit
- Half-precision floating point support (part of ARMv8.2)
- Optimisations for CPUs with or without a hardware prefetcher (using
run-time code patching)
- copy_page performance improvement to deal with 128 bytes at a time
- Sanity checks on the CPU capabilities (via CPUID) to prevent
incompatible secondary CPUs from being brought up (e.g. weird
big.LITTLE configurations)
- valid_user_regs() reworked for better sanity check of the
sigcontext information (restored pstate information)
- ACPI parking protocol implementation
- CONFIG_DEBUG_RODATA enabled by default
- VDSO code marked as read-only
- DEBUG_PAGEALLOC support
- ARCH_HAS_UBSAN_SANITIZE_ALL enabled
- Erratum workaround Cavium ThunderX SoC
- set_pte_at() fix for PROT_NONE mappings
- Code clean-ups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (99 commits)
arm64: kasan: Fix zero shadow mapping overriding kernel image shadow
arm64: kasan: Use actual memory node when populating the kernel image shadow
arm64: Update PTE_RDONLY in set_pte_at() for PROT_NONE permission
arm64: Fix misspellings in comments.
arm64: efi: add missing frame pointer assignment
arm64: make mrs_s prefixing implicit in read_cpuid
arm64: enable CONFIG_DEBUG_RODATA by default
arm64: Rework valid_user_regs
arm64: mm: check at build time that PAGE_OFFSET divides the VA space evenly
arm64: KVM: Move kvm_call_hyp back to its original localtion
arm64: mm: treat memstart_addr as a signed quantity
arm64: mm: list kernel sections in order
arm64: lse: deal with clobbered IP registers after branch via PLT
arm64: mm: dump: Use VA_START directly instead of private LOWEST_ADDR
arm64: kconfig: add submenu for 8.2 architectural features
arm64: kernel: acpi: fix ioremap in ACPI parking protocol cpu_postboot
arm64: Add support for Half precision floating point
arm64: Remove fixmap include fragility
arm64: Add workaround for Cavium erratum 27456
arm64: mm: Mark .rodata as RO
...
With ARMv8.1 VHE, the architecture is able to (almost) transparently
run the kernel at EL2, despite being written for EL1.
This patch takes care of the "almost" part, mostly preventing the kernel
from dropping from EL2 to EL1, and setting up the HYP configuration.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A secondary CPU could fail to come online due to insufficient
capabilities and could simply die or loop in the kernel.
e.g, a CPU with no support for the selected kernel PAGE_SIZE
loops in kernel with MMU turned off.
or a hotplugged CPU which doesn't have one of the advertised
system capability will die during the activation.
There is no way to synchronise the status of the failing CPU
back to the master. This patch solves the issue by adding a
field to the secondary_data which can be updated by the failing
CPU. If the secondary CPU fails even before turning the MMU on,
it updates the status in a special variable reserved in the head.txt
section to make sure that the update can be cache invalidated safely
without possible sharing of cache write back granule.
Here are the possible states :
-1. CPU_MMU_OFF - Initial value set by the master CPU, this value
indicates that the CPU could not turn the MMU on, hence the status
could not be reliably updated in the secondary_data. Instead, the
CPU has updated the status @ __early_cpu_boot_status.
0. CPU_BOOT_SUCCESS - CPU has booted successfully.
1. CPU_KILL_ME - CPU has invoked cpu_ops->die, indicating the
master CPU to synchronise by issuing a cpu_ops->cpu_kill.
2. CPU_STUCK_IN_KERNEL - CPU couldn't invoke die(), instead is
looping in the kernel. This information could be used by say,
kexec to check if it is really safe to do a kexec reboot.
3. CPU_PANIC_KERNEL - CPU detected some serious issues which
requires kernel to crash immediately. The secondary CPU cannot
call panic() until it has initialised the GIC. This flag can
be used to instruct the master to do so.
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[catalin.marinas@arm.com: conflict resolution]
[catalin.marinas@arm.com: converted "status" from int to long]
[catalin.marinas@arm.com: updated update_early_cpu_boot_status to use str_l]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This adds support for KASLR is implemented, based on entropy provided by
the bootloader in the /chosen/kaslr-seed DT property. Depending on the size
of the address space (VA_BITS) and the page size, the entropy in the
virtual displacement is up to 13 bits (16k/2 levels) and up to 25 bits (all
4 levels), with the sidenote that displacements that result in the kernel
image straddling a 1GB/32MB/512MB alignment boundary (for 4KB/16KB/64KB
granule kernels, respectively) are not allowed, and will be rounded up to
an acceptable value.
If CONFIG_RANDOMIZE_MODULE_REGION_FULL is enabled, the module region is
randomized independently from the core kernel. This makes it less likely
that the location of core kernel data structures can be determined by an
adversary, but causes all function calls from modules into the core kernel
to be resolved via entries in the module PLTs.
If CONFIG_RANDOMIZE_MODULE_REGION_FULL is not enabled, the module region is
randomized by choosing a page aligned 128 MB region inside the interval
[_etext - 128 MB, _stext + 128 MB). This gives between 10 and 14 bits of
entropy (depending on page size), independently of the kernel randomization,
but still guarantees that modules are within the range of relative branch
and jump instructions (with the caveat that, since the module region is
shared with other uses of the vmalloc area, modules may need to be loaded
further away if the module region is exhausted)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This implements CONFIG_RELOCATABLE, which links the final vmlinux
image with a dynamic relocation section, allowing the early boot code
to perform a relocation to a different virtual address at runtime.
This is a prerequisite for KASLR (CONFIG_RANDOMIZE_BASE).
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Before implementing KASLR for arm64 by building a self-relocating PIE
executable, we have to ensure that values we use before the relocation
routine is executed are not subject to dynamic relocation themselves.
This applies not only to virtual addresses, but also to values that are
supplied by the linker at build time and relocated using R_AARCH64_ABS64
relocations.
So instead, use assemble time constants, or force the use of static
relocations by folding the constants into the instructions.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Unfortunately, the current way of using the linker to emit build time
constants into the Image header will no longer work once we switch to
the use of PIE executables. The reason is that such constants are emitted
into the binary using R_AARCH64_ABS64 relocations, which are resolved at
runtime, not at build time, and the places targeted by those relocations
will contain zeroes before that.
So refactor the endian swapping linker script constant generation code so
that it emits the upper and lower 32-bit words separately.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This relaxes the kernel Image placement requirements, so that it
may be placed at any 2 MB aligned offset in physical memory.
This is accomplished by ignoring PHYS_OFFSET when installing
memblocks, and accounting for the apparent virtual offset of
the kernel Image. As a result, virtual address references
below PAGE_OFFSET are correctly mapped onto physical references
into the kernel Image regardless of where it sits in memory.
Special care needs to be taken for dealing with memory limits passed
via mem=, since the generic implementation clips memory top down, which
may clip the kernel image itself if it is loaded high up in memory. To
deal with this case, we simply add back the memory covering the kernel
image, which may result in more memory to be retained than was passed
as a mem= parameter.
Since mem= should not be considered a production feature, a panic notifier
handler is installed that dumps the memory limit at panic time if one was
set.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This introduces the preprocessor symbol KIMAGE_VADDR which will serve as
the symbolic virtual base of the kernel region, i.e., the kernel's virtual
offset will be KIMAGE_VADDR + TEXT_OFFSET. For now, we define it as being
equal to PAGE_OFFSET, but in the future, it will be moved below it once
we move the kernel virtual mapping out of the linear mapping.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently the zero page is set up in paging_init, and thus we cannot use
the zero page earlier. We use the zero page as a reserved TTBR value
from which no TLB entries may be allocated (e.g. when uninstalling the
idmap). To enable such usage earlier (as may be required for invasive
changes to the kernel page tables), and to minimise the time that the
idmap is active, we need to be able to use the zero page before
paging_init.
This patch follows the example set by x86, by allocating the zero page
at compile time, in .bss. This means that the zero page itself is
available immediately upon entry to start_kernel (as we zero .bss before
this), and also means that the zero page takes up no space in the raw
Image binary. The associated struct page is allocated in bootmem_init,
and remains unavailable until this time.
Outside of arch code, the only users of empty_zero_page assume that the
empty_zero_page symbol refers to the zeroed memory itself, and that
ZERO_PAGE(x) must be used to acquire the associated struct page,
following the example of x86. This patch also brings arm64 inline with
these assumptions.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Laura Abbott <labbott@fedoraproject.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The Performance Monitors extension is an optional feature of the
AArch64 architecture, therefore, in order to access Performance
Monitors registers safely, the kernel should detect the architected
PMU unit presence through the ID_AA64DFR0_EL1 register PMUVer field
before accessing them.
This patch implements a guard by reading the ID_AA64DFR0_EL1 register
PMUVer field to detect the architected PMU presence and prevent accessing
PMU system registers if the Performance Monitors extension is not
implemented in the core.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: 60792ad349 ("arm64: kernel: enforce pmuserenr_el0 initialization and restore")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently we use an open-coded memzero to clear the BSS. As it is a
trivial implementation, it is sub-optimal.
Our optimised memset doesn't use the stack, is position-independent, and
for the memzero case can use of DC ZVA to clear large blocks
efficiently. In __mmap_switched the MMU is on and there are no live
caller-saved registers, so we can safely call an uninstrumented memset.
This patch changes __mmap_switched to use memset when clearing the BSS.
We use the __pi_memset alias so as to avoid any instrumentation in all
kernel configurations.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There is need for figuring out how to manage struct thread_info data when
IRQ stack is introduced. struct thread_info information should be copied
to IRQ stack under the current thread_info calculation logic whenever
context switching is invoked. This is too expensive to keep supporting
the approach.
Instead, this patch pays attention to sp_el0 which is an unused scratch
register in EL1 context. sp_el0 utilization not only simplifies the
management, but also prevents text section size from being increased
largely due to static allocated IRQ stack as removing masking operation
using THREAD_SIZE in many places.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jungseok Lee <jungseoklee85@gmail.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWOkmIAAoJEGvWsS0AyF7x4GgQAINU3NePjFFvWZNCkqobeH9+
jFKwtXamIudhTSdnXNXyYWmtRL9Krg3qI4zDQf68dvDFAZAze2kVuOi1yPpCbpFZ
/j/afNyQc7+PoyqRAzmT+EMPZlcuOA84Prrl1r3QWZ58QaFeVk/6ZxrHunTHxN0x
mR9PIXfWx73MTo+UnG8FChkmEY6LmV4XpemgTaMR9FqFhdT51OZSxDDAYXOTm4JW
a5HdN9OWjjJ2rhLlFEaC7tszG9B5doHdy2tr5ge/YERVJzIPDogHkMe8ZhfAJc+x
SQU5tKN6Pg4MOi+dLhxlk0/mKCvHLiEQ5KVREJnt8GxupAR54Bat+DQ+rP9cSnpq
dRQTcARIOyy9LGgy+ROAsSo+NiyM5WuJ0/WJUYKmgWTJOfczRYoZv6TMKlwNOUYb
tGLCZHhKPM3yBHJlWbQykl3xmSuudxCMmjlZzg7B+MVfTP6uo0CRSPmYl+v67q+J
bBw/Z2RYXWYGnvlc6OfbMeImI6prXeE36+5ytyJFga0m+IqcTzRGzjcLxKEvdbiU
pr8n9i+hV9iSsT/UwukXZ8ay6zH7PrTLzILWQlieutfXlvha7MYeGxnkbLmdYcfe
GCj374io5cdImHcVKmfhnOMlFOLuOHphl9cmsd/O2LmCIqBj9BIeNH2Om8mHVK2F
YHczMdpESlJApE7kUc1e
=3six
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (91 commits)
arm64/efi: fix libstub build under CONFIG_MODVERSIONS
ARM64: Enable multi-core scheduler support by default
arm64/efi: move arm64 specific stub C code to libstub
arm64: page-align sections for DEBUG_RODATA
arm64: Fix build with CONFIG_ZONE_DMA=n
arm64: Fix compat register mappings
arm64: Increase the max granular size
arm64: remove bogus TASK_SIZE_64 check
arm64: make Timer Interrupt Frequency selectable
arm64/mm: use PAGE_ALIGNED instead of IS_ALIGNED
arm64: cachetype: fix definitions of ICACHEF_* flags
arm64: cpufeature: declare enable_cpu_capabilities as static
genirq: Make the cpuhotplug migration code less noisy
arm64: Constify hwcap name string arrays
arm64/kvm: Make use of the system wide safe values
arm64/debug: Make use of the system wide safe value
arm64: Move FP/ASIMD hwcap handling to common code
arm64/HWCAP: Use system wide safe values
arm64/capabilities: Make use of system wide safe value
arm64: Delay cpu feature capability checks
...
Ensure that the selected page size is supported by the CPU(s). If it doesn't
park it.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
At the moment, we only support maximum of 3-level page table for
swapper. With 48bit VA, 64K has only 3 levels and 4K uses section
mapping. Add support for 4-level page table for swapper, needed
by 16K pages.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Move the kernel pagetable (both swapper and idmap) definitions
from the generic asm/page.h to a new file, asm/kernel-pgtable.h.
This is mostly a cosmetic change, to clean up the asm/page.h to
get rid of the arch specific details which are not needed by the
generic code.
Also renames the symbols to prevent conflicts. e.g,
BLOCK_SHIFT => SWAPPER_BLOCK_SHIFT
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds arch specific code for kernel address sanitizer
(see Documentation/kasan.txt).
1/8 of kernel addresses reserved for shadow memory. There was no
big enough hole for this, so virtual addresses for shadow were
stolen from vmalloc area.
At early boot stage the whole shadow region populated with just
one physical page (kasan_zero_page). Later, this page reused
as readonly zero shadow for some memory that KASan currently
don't track (vmalloc).
After mapping the physical memory, pages for shadow memory are
allocated and mapped.
Functions like memset/memmove/memcpy do a lot of memory accesses.
If bad pointer passed to one of these function it is important
to catch this. Compiler's instrumentation cannot do this since
these functions are written in assembly.
KASan replaces memory functions with manually instrumented variants.
Original functions declared as weak symbols so strong definitions
in mm/kasan/kasan.c could replace them. Original functions have aliases
with '__' prefix in name, so we could call non-instrumented variant
if needed.
Some files built without kasan instrumentation (e.g. mm/slub.c).
Original mem* function replaced (via #define) with prefixed variants
to disable memory access checks for such files.
Signed-off-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since arm64 does not use a builtin decompressor, the EFI stub is built
into the kernel proper. So far, this has been working fine, but actually,
since the stub is in fact a PE/COFF relocatable binary that is executed
at an unknown offset in the 1:1 mapping provided by the UEFI firmware, we
should not be seamlessly sharing code with the kernel proper, which is a
position dependent executable linked at a high virtual offset.
So instead, separate the contents of libstub and its dependencies, by
putting them into their own namespace by prefixing all of its symbols
with __efistub. This way, we have tight control over what parts of the
kernel proper are referenced by the stub.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Contrary to what was originally expected, EL3 firmware can (for whatever
reason) disable GICv3 system register access. In this case, the kernel
explodes very early.
Work around this by testing if the SRE bit sticks or not. If it doesn't,
abort the GICv3 setup, and pray that the firmware has passed a DT that
doesn't contain a GICv3 node.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When entering the kernel at EL2, we fail to initialise the MDCR_EL2
register which controls debug access and PMU capabilities at EL1.
This patch ensures that the register is initialised so that all traps
are disabled and all the PMU counters are available to the host. When a
guest is scheduled, KVM takes care to configure trapping appropriately.
Cc: <stable@vger.kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 booting document requires that the bootloader has cleaned the
kernel image to the PoC. However, when a CPU re-enters the kernel due to
either a CPU hotplug "on" event or resuming from a low-power state (e.g.
cpuidle), the kernel text may in-fact be dirty at the PoU due to things
like alternative patching or even module loading.
Thanks to I-cache speculation with the MMU off, stale instructions could
be fetched prior to enabling the MMU, potentially leading to crashes
when executing regions of code that have been modified at runtime.
This patch addresses the issue by ensuring that the local I-cache is
invalidated immediately after a CPU has enabled its MMU but before
jumping out of the identity mapping. Any stale instructions fetched from
the PoC will then be discarded and refetched correctly from the PoU.
Patching kernel text executed prior to the MMU being enabled is
prohibited, so the early entry code will always be clean.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Nobody seems to be producing !SMP systems anymore, so this is just
becoming a source of kernel bugs, particularly if people want to use
coherent DMA with non-shared pages.
This patch forces CONFIG_SMP=y for arm64, removing a modest amount of
code in the process.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit ea8c2e1124 ("arm64: Extend the idmap to the whole kernel
image") changed the early page table code so that the entire kernel
Image is covered by the identity map. This allows functions that
need to enable or disable the MMU to reside anywhere in the kernel
Image.
However, this change has the unfortunate side effect that the Image
cannot cross a physical 512 MB alignment boundary anymore, since the
early page table code cannot deal with the Image crossing a /virtual/
512 MB alignment boundary.
So instead, reduce the ID map to a single page, that is populated by
the contents of the .idmap.text section. Only three functions reside
there at the moment: __enable_mmu(), cpu_resume_mmu() and cpu_reset().
If new code is introduced that needs to manipulate the MMU state, it
should be added to this section as well.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently, the FDT blob needs to be in the same 512 MB region as
the kernel, so that it can be mapped into the kernel virtual memory
space very early on using a minimal set of statically allocated
translation tables.
Now that we have early fixmap support, we can relax this restriction,
by moving the permanent FDT mapping to the fixmap region instead.
This way, the FDT blob may be anywhere in memory.
This also moves the vetting of the FDT to mmu.c, since the early
init code in head.S does not handle mapping of the FDT anymore.
At the same time, fix up some comments in head.S that have gone stale.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We write idmap_t0sz with SCTLR_EL1.{C,M} clear, but we only have the
guarnatee that the kernel Image is clean, not invalid in the caches, and
therefore we might read a stale value once the MMU is enabled.
This patch ensures we invalidate the corresponding cacheline after the
write as we do for all other data written before we set SCTLR_EL1.{C.M},
guaranteeing that the value will be visible later. We rely on the DSBs
in __create_page_tables to complete the maintenance.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
CC: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
After writing the page tables, we use __inval_cache_range to invalidate
any stale cache entries. Strongly Ordered memory accesses are not
ordered w.r.t. cache maintenance instructions, and hence explicit memory
barriers are required to provide this ordering. However,
__inval_cache_range was written to be used on Normal Cacheable memory
once the MMU and caches are on, and does not have any barriers prior to
the DC instructions.
This patch adds a DMB between the page tables being written and the
corresponding cachelines being invalidated, ensuring that the
invalidation makes the new data visible to subsequent cacheable
accesses. A barrier is not required before the prior invalidate as we do
not access the page table memory area prior to this, and earlier
barriers in preserve_boot_args and set_cpu_boot_mode_flag ensures
ordering w.r.t. any stores performed prior to entering Linux.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: c218bca74e ("arm64: Relax the kernel cache requirements for boot")
Signed-off-by: Will Deacon <will.deacon@arm.com>
The page size and the number of translation levels, and hence the supported
virtual address range, are build-time configurables on arm64 whose optimal
values are use case dependent. However, in the current implementation, if
the system's RAM is located at a very high offset, the virtual address range
needs to reflect that merely because the identity mapping, which is only used
to enable or disable the MMU, requires the extended virtual range to map the
physical memory at an equal virtual offset.
This patch relaxes that requirement, by increasing the number of translation
levels for the identity mapping only, and only when actually needed, i.e.,
when system RAM's offset is found to be out of reach at runtime.
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
According to the arm64 boot protocol, registers x1 to x3 should be
zero upon kernel entry, and non-zero values are reserved for future
use. This future use is going to be problematic if we never enforce
the current rules, so start enforcing them now, by emitting a warning
if non-zero values are detected.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This removes the function __calc_phys_offset and all open coded
virtual to physical address translations using the offset kept
in x28.
Instead, just use absolute or PC-relative symbol references as
appropriate when referring to virtual or physical addresses,
respectively.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Enabling of the MMU is split into two functions, with an align and
a branch in the middle. On arm64, the entire kernel Image is ID mapped
so this is really not necessary, and we can just merge it into a
single function.
Also replaces an open coded adrp/add reference to __enable_mmu pair
with adr_l.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Replace the confusing virtual/physical address arithmetic with a simple
PC-relative reference.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This removes the confusing __switch_data object from head.S,
and replaces it with standard PC-relative references to the
various symbols it encapsulates.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The global processor_id is assigned the MIDR_EL1 value of the boot
CPU in the early init code, but is never referenced afterwards.
As the relevance of the MIDR_EL1 value of the boot CPU is debatable
anyway, especially under big.LITTLE, let's remove it before anyone
starts using it.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
struct cpu_table is an artifact left from the (very) early days of
the arm64 port, and its only real use is to allow the most beautiful
"AArch64 Processor" string to be displayed at boot time.
Really? Yes, really.
Let's get rid of it. In order to avoid another BogoMips-gate, the
aforementioned string is preserved.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 828e9834e9 ("arm64: head: create a new function for setting
the boot_cpu_mode flag") added BOOT_CPU_MODE_EL1, a nonzero value
replacing uses of zero. However it failed to update __boot_cpu_mode
appropriately.
A CPU booted at EL2 writes BOOT_CPU_MODE_EL2 to __boot_cpu_mode[0], and
a CPU booted at EL1 writes BOOT_CPU_MODE_EL1 to __boot_cpu_mode[1].
Later is_hyp_mode_mismatched() determines there to be a mismatch if
__boot_cpu_mode[0] != __boot_cpu_mode[1].
If all CPUs are booted at EL1, __boot_cpu_mode[0] will be set to
BOOT_CPU_MODE_EL1, but __boot_cpu_mode[1] will retain its initial value
of zero, and is_hyp_mode_mismatched will erroneously determine that the
boot modes are mismatched. This hasn't been a problem so far, but later
patches which will make use of is_hyp_mode_mismatched() expect it to
work correctly.
This patch initialises __boot_cpu_mode[1] to BOOT_CPU_MODE_EL1, fixing
the erroneous mismatch detection when all CPUs are booted at EL1.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Another one for the big head.S spring cleaning: the label should
be after the .align or it may point to the padding.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
