[Why]
Currently Z10 save/restore only covers 1 plane case. If we enter
Z10 with 2 planes enabled, 1 of the 2 planes will not be restored.
causing black screen.
[How]
Disable Zstate when more than 1 plane is enabled. Right now Z9 enable
but Z10 disable is not a supported config, so we disable both.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. To leverage and simplify the igt tool. Change the value of
retrain when calling preferred training settings.
Now, writing value to link settings triggers link training immediately.
2. Add dc lock when triggering link training in edp_ilr_write()
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To debug when p-state is being blocked and avoid PMFW hangs when
it does occur.
[How]
Re-use the DCN10 hardware sequencer by adding a new interface for
verifying p-state high on the hubbub. The interface is mostly the
same as the DCN10 interface, but the bit definitions have changed for
the debug bus.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The DP KVM failed to light up, since the lttpr_mode is not reset to
default value when failed to read LTTPR capabilities, and the
variable max_link_rate retains a initial value zero, this cause variable
link_rate be assigned to an error value zero, consquently pixel_clock
get wrong value zero, and kvm can't light up.
[how]
Reset lttpr_mode to default value when failed to read LTTPR
capabilities, so that the link_rate fallbacks to the minimum rate that
supported by link encoder and sink.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Tianci.Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
FPU operations in dcn10 was already moved to dml folder via calcs code.
However, dcn1_0_ip and dcn_1_0_soc with FPU componentd remains on dcn10.
Following previous changes to isolate FPU, this patch creates dcn10_fpu
files to isolate FPU-specific code and moves those structs to it.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dml/dcn20_fpu file centralizes all DCN2x functions that require FPU access.
Therefore, this patch moves FPU-related code from dcn21 to dcn20_fpu. These
include:
- dcn21_populate_dml_pipes_from_context()
- dcn21_validate_bandwidth_fp() and related:
- dcn21_calculate_wm(),
- patch_bounding_box(),
- calculate_wm_set_for_vlevel()
- renaming update_bw_bounding_box() to dcn21_update_bw_bounding_box(), move
to dcn20_fpu with related static function construct_low_pstate_lvl()
Also, make dcn21_fast_validate_bw() public in dcn21_resource as it is called
by dcn21_validate_bandwidth_fp() now in dcn20_fpu.
Reuse dcn20_fpu_adjust_dppclk() in dcn21_fast_validate_bw() as it isolates
the same FPU operation.
Include dchubbub.h as it is required in dcn21_populate_dml_pipes_from_context()
Signed-off-by: Melissa Wen <mwen@igalia.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move parts of dcn20 code that uses FPU to dml folder. It aims to isolate
FPU operations as described by series:
drm/amd/display: Introduce FPU directory inside DC
https://patchwork.freedesktop.org/series/93042/
This patch moves the following functions from dcn20_resource to
dml/dcn20_fpu and calls of public functions in dcn20_resource are
wrapped by DC_FP_START/END():
- void dcn20_populate_dml_writeback_from_context
- static bool is_dtbclk_required()
- static enum dcn_zstate_support_state()
- void dcn20_calculate_dlg_params()
- static void swizzle_to_dml_params()
- int dcn20_populate_dml_pipes_from_context()
- void dcn20_calculate_wm()
- void dcn20_cap_soc_clocks()
- void dcn20_update_bounding_box()
- void dcn20_patch_bounding_box()
- bool dcn20_validate_bandwidth_fp()
This movement also affects dcn21/30/31, as dcn20_calculate_dlg_params()
is used by them. For this reason, I included dcn20_fpu headers in
dcn20_resource headers to make dcn20_calculate_dlg_params() visible to
dcn21/30/31.
Three new functions are created to isolate well-delimited FPU
operations:
- void dcn20_fpu_set_wb_arb_params(): set cli_watermark,
pstate_watermark and time_per_pixel from wb_arb_params (struct
mcif_arb_params), since those uses FPU operations on double types:
WritebackUrgentWatermark, WritebackDRAMClockChangeWatermark, '16.0'.
- void dcn20_fpu_set_wm_ranges(): set min_fill_clk_mhz and
max_fill_clk_mhz involves FPU calcs on dram_speed_mts (double type);
- void dcn20_fpu_adjust_dppclk(): adjust operation on RequiredDPPCLK
that is a double.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On LNX, TO_CLK_MGR_INTERNAL() only works to get clk_mgr_internal from a
given clk_mgr. In clk_mgr_dcn316 struct, the clk_mgr_internal is already
a memeber by the alias 'base'
[How]
Use &clk_mgr->base instead.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The issue only occurs during the GPU reset code path.
We first backup the current state prior to commiting 0 streams
internally from DM to DC. This state backup contains valid link
encoder assignments.
DC will clear the link encoder assignments as part of current state
(but not the backup, since it was a copied before the commit) and
free the extra stream reference it held.
DC requires that the link encoder assignments remain cleared/invalid
prior to commiting. Since the backup still has valid assignments we
call the interface post reset to clear them. This routine also
releases the extra reference that the link encoder interface held -
resulting in a double free (and eventually a NULL pointer dereference).
[How]
We'll have to do a full DC commit anyway after GPU reset because
the stream count previously went to 0.
We don't need to retain the assignment that we had backed up, so
just copy off of the now clean current state assignment after the
reset has occcurred with the new link_enc_cfg_copy() interface.
Fixes: 6d63fcc2a3 ("drm/amd/display: Reset link encoder assignments for GPU reset")
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Virtualization enters blue screen of death (BSoD)
due to NULL res_pool object when accessing DSC
encoder capability.
[How]
Add NULL check to avoid blue screen of death.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: 3.2.176
This version brings along following fixes:
- move FPU operations from dcn21 to dml/dcn20 folder
- move FPU-related code from dcn20 to dml folder
- Fix compile error from TO_CLK_MGR_INTERNAL
- Fix double free during GPU reset on DC streams
- Add NULL check
- [FW Promotion] Release 0.0.107.0
- enable dcn315/316 s0i2 support
- handle DP2.0 RX with UHBR20 but not UHBR13.5 support
- disable HPD SW timer for passive dongle type 1 only
- add gamut coefficient set A and B
- merge two duplicated clock_source_create
- Add link dp trace support
- move FPU associated DCN303 code to DML folder
- Release AUX engine after failed acquire
- Add minimal pipe split transition state
- Clean up fixed VS PHY test w/a function
- fix the clock source contruct for dcn315
- cleaning up smu_if to add future flexibility
- fix deep color ratio
- add debug option to bypass ssinfo from bios for dcn315
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP2.0 defines DP2.0 RX capability using bit maps. This means there is
a corner case the DP2.0 RX can declare UHBR20 capability but not UHBR13.5 support.
In this case we should skip UHBR13.5 selection and continue to our next option
in decide liink settings.
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is nice to have link training and link loss status logging in
our trace, and this patch add the all necessary accessors in dc
side.
[How]
1. Define dp_trace struct and create new file link_dp_trace.c and
link_dp_trace.h;
2. Add dp link training status update in dc_link_dp.c;
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a sequence in which aux arbitration
doesn't work correctly. Driver is left with
aux access after it times out waiting for access.
In future dmub fw is never granted aux access
and is stuck in a while loop.
[How]
Cancel aux request from driver after timing out.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?] When adding/removng a plane to some configurations,
unsupported pipe programming can occur when moving to a new plane.
[HOW?]
Add a safe transistion state before programming new configuration.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: 3.2.175
This version brings along following fixes:
- Remove invalid RDPCS Programming in DAL
- Make functional resource functions non-static
- Reset VIC if HDMI_VIC is present
- Add frame alternate 3D & restrict HW packed on dongles
- Reg to turn on/off PSR Power seq in FSM
- Modify plane removal sequence to avoid hangs
- Pass HostVM enable flag into DCN3.1 DML
- DC Validation failures
- Program OPP before ODM
- Refactor fixed VS w/a for PHY tests
- Pass deep sleep disabled allow info to dmub fw
- Refine the EDID override
- [FW Promotion] Release 0.0.106.0
- Add verify_link_cap back for hdmi
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We already get the SBIOS EDID via ACPI on KMD,
but after that, we just use the monitor EDID to set it HDR caps
[How]
Make the SBIOS EDID override to read_edid()
That can change the read EDID caps from the right EDID
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: jinzh <jinzh@github.amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Calculations differ with HostVM enabled/disabled, causing underflow in
configs with high refresh displays + scaling due to lower available BW
[HOW]
Check riommu_active in order to pass correct HostVM enablement to DML
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Some projectors support frame alternate 3D modes at 120Hz, but DAL3 does
not create timings. Most active DP to HDMI dongles do not translate
infoframes properly to use HW packing stereo mode.
[HOW?]
Create frame alternate 3D timings for displays that support it. Disable HW
packing 3D mode on DP active dongles.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't fill up the logs with:
[253557.859575] [drm:amdgpu_dm_atomic_check [amdgpu]] DSC precompute is not needed.
[253557.892966] [drm:amdgpu_dm_atomic_check [amdgpu]] DSC precompute is not needed.
[253557.926070] [drm:amdgpu_dm_atomic_check [amdgpu]] DSC precompute is not needed.
[253557.959344] [drm:amdgpu_dm_atomic_check [amdgpu]] DSC precompute is not needed.
which prints many times a second, when the kernel is run with
drm.debug=2.
Instead of DRM_DEBUG_DRIVER(), make it DRM_INFO_ONCE().
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Roman Li <Roman.Li@amd.com>
Cc: Felix Kuehling <felix.kuehling@amd.com>
Cc: Hersen Wu <hersenwu@amd.com>
Cc: Daniel Wheeler <daniel.wheeler@amd.com>
Fixes: 17ce8a6907 ("drm/amd/display: Add dsc pre-validation in atomic check")
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Silence [-Wmissing-prototypes] sparse warnings from the display folder
such as:
../drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn315/dcn315_smu.c:126:5: warning: no previous prototype for ‘dcn315_smu_send_msg_with_param’ [-Wmissing-prototypes]
126 | int dcn315_smu_send_msg_with_param(
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
v2: drop unused function dcn315_smu_set_voltage_via_phyclk() to avoid
adding a warning (Alex)
Cc: Qingqing Zhuo (Lillian) <qingqing.zhuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Silence the following sparse warnings:
../drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:865:16:
sparse: warning: Using plain integer as NULL pointer
../drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:1588:84:
sparse: warning: Using plain integer as NULL pointer
../drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:2725:84:
sparse: warning: Using plain integer as NULL pointer
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1919:16:
sparse: warning: Using plain integer as NULL pointer
v2: drop removal of default case to avoid adding warnings (Alex)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When CONFIG_DRM_AMD_DC_DCN is not set, the function
'dm_helpers_enable_periodic_detection' doesn't have its prototype defined,
causing the following warning:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_helpers.c:805:6:
warning: no previous prototype for function 'dm_helpers_enable_periodic_detection' [-Wmissing-prototypes]
void dm_helpers_enable_periodic_detection(struct dc_context *ctx, bool enable)
^
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_helpers.c:805:1:
note: declare 'static' if the function is not intended to be used outside
of this translation unit
void dm_helpers_enable_periodic_detection(struct dc_context *ctx, bool enable)
^
static
1 warning generated.
This commit silences this warning by adding a conditional directive
around the mentioned function, and also corrects a small spelling error.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Part of the documentation of the 'dc_process_dmub_aux_transfer_async'
function was misplaced, being put together with the
‘dc_enable_dmub_notifications’ documentation. This caused the following
warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:3757: warning:
expecting prototype for dc_process_dmub_aux_transfer_async(). Prototype
was for dc_enable_dmub_notifications() instead
This commit fixes the warning by placing the function documentations in
their right place.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
