[Why]
Calculation of scaling ratio can result in a crash due to zero'd src or
dst plane rects.
[How]
Validate that src and dst rects are valid before using for scaling
calculations.
Reviewed-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hardware team has recommended to generically hard code this register to
0xFF as part of the effort to eventually remove this control. However
we set it to 0xF instead.
This causes 4 of audio 8ch to be muted.
Reviewed-by: Ariel Bernstein <eric.bernstein@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly plugging and unplugging a DP sink, detection link
training can be mistakenly skipped.
This is due to the hotplug processing occurring before the
encoder assignment logic has had a chance to process the removal
of a stream. The encoder that would be used for detection link
training is then erroneously reported as already in use and
detection link training is skipped.
[How]
During hot plug processing, only determine a link encoder to be
unavailable for a particular link if it has been assigned to a
different link.
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When copying a stream, the encoder assigned to it is copied too.
Encoder assignment should only happen when executing the encoder
assignment function link_encs_assign().
[How]
Clear the link encoder pointer for copied stream.
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On renoir usb-c port stops functioning on resume after f/w update.
New dmub firmware caused regression due to conflict with dmcu.
With new dmub f/w dmcu is superseded and should be disabled.
[How]
- Disable dmcu for all dcn21.
Check dmesg for dmub f/w version.
The old firmware (before regression):
[drm] DMUB hardware initialized: version=0x00000001
All other versions require this patch for renoir.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1735
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Size can be any value and is user controlled resulting in overwriting the
40 byte array wr_buf with an arbitrary length of data from buf.
Signed-off-by: Thelford Williams <tdwilliamsiv@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
When system boots in headless mode, connecting a 4k display creates a
null pointer dereference due to hubp for a certain plane being null.
Add a condition to check for null hubp before dereferencing it.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE legacy optimization path isn't well tested under new DC optimization
flow which can result in underflow occuring when initializing X11 on
Carrizo.
[How]
Retain the legacy optimization flow for DCE and keep the new one for DCN
to satisfy optimizations being correctly applied for ASIC that can
support it.
Fixes: 34316c1e56 ("drm/amd/display: Optimize bandwidth on following fast update")
Reported-by: Tom St Denis <tom.stdenis@amd.com>
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For optimal power savings on panels that can support it.
This was previously left disabled by default because of issues with
compositors that do not pageflip and scan out directly to the
frontbuffer.
For these compositors we now have detection methods that wait for x
number of pageflips after a full update - triggered by a buffer or
format change typically.
This may introduce bugs or new cases not tested by users so this is
only currently targeting newer DCN.
[How]
Add code in DM to set PSR state by default for newer DCN while falling
back to the feature mask for older.
Add a global debug flag that can be set to disable it for either.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Got Werror when building with Clang-13:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dpia.c:195:2:
error: variable 'ts' is used uninitialized whenever switch default is
taken [-Werror,-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dpia.c:200:9:
note: uninitialized use occurs here
return ts;
^~
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dpia.c:180:2:
note: variable 'ts' is declared here
enum dpia_set_config_ts ts;
^
1 error generated.
Fix it.
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable result is being initialized with a value that is never
read, it is being updated immediately afterwards in both branches
of an if statement. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Overriding link setting inside override_training_settings
result in fallback link settings being ignored. This can
potentially cause link training to always fail and consequently
result in an infinite loop of link training to occur in
dp_verify_link_cap during detection.
[How]
Since preferred link settings are already considered inside
decide_link_settings, skip the check in override_training_settings
to avoid infinite link training loops.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For those video format with 60 fps, the user space player could
ask for 120Hz for playback.
[How]
Add 120 in the table of common rates.
Signed-off-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
1. HPD callback function has deadlock problem
2. HPD status is not assigned
3. There is crash due to null pointer
4. link_enc is NULL in DPIA case
[How]
1. Fix deadlock problem by moving it out of the
drm_modeset_lock
2. Assign HPD status from the notify of outbox
from dmub FW
3. Fix the crash by checking if pin or enc exists
4. Use link_enc_cfg_get_link_enc_used_by_link to
dynamically assign
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jude Shih <shenshih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DIB_BE_CNTL<i>.DIG_HPD_SELECT selects the HPD block being used
by the display endpoint assigned to DIG<i>. In the case of USB4
display endpoints, no physical HPD block is assigned.
[How]
Setting DIB_BE_CNTL<i>.DIG_HPD_SELECT to 5 indicates that no HPD
is assigned to a display endpoint. Firmware decrements the
HPD_SELECT value by 1 before writing it to the register.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To process SET_CONFIG transactions with DMUB using inbox1 and
outbox1 mail boxes.
[How]
1) DMUB posts SET_CONFIG reply as an Outbox1 message of type
DMUB_OUT_CMD__SET_CONFIG_REPLY.
2) The dmub async to sync mechanism for AUX is modified to accommodate
SET_CONFIG commands for both command issue and reply code paths.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jude Shih <shenshih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To process SET_CONFIG transactions with DMUB using inbox1 and
outbox1 mail boxes.
[How]
1) Added inbox1 DPIA command subtype DMUB_CMD__DPIA_SET_CONFIG_ACCESS to
issue SET_CONFIG command to DMUB in dc_process_dmub_set_config_async().
DMUB processes the command with DPIA sends reply back immediately or
in an outbox1 message triggering an outbox1 interrupt to driver.
2) DMUB posts SET_CONFIG reply as an Outbox1 message of type
DMUB_OUT_CMD__SET_CONFIG_REPLY.
3) The dmub async to sync mechanism for AUX is modified to accommodate
SET_CONFIG commands for both command issue and reply code paths.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Training settings need to be applied to DPIA link at start of each
training loop. Note: FEC readiness should be configured before link
training while FEC enablement should be configured once training is
complete.
[How]
- Implement DPIA link configuration function.
- Account for dynamically assigned link encoders during link
configuration.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Training of DPIA link differs enough from that of conventional
DP link to warrant a separate implementation.
[How]
- Implement top-level of DPIA training loop.
- Make functions shared between DP and DPIA link training "public".
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To add support for HPD & HPD RX interrupt handling for USB4 DPIA in
YELLOW_CARP_B0. USB4 DPIA HPD & HPD RX interrupts are issued from DMUB to
driver as a outbox1 message.
[HOW]
1) Created get_link_index_from_dpia_port_index() to retrieve link index
from dpia port index for HPD & HPD RX dmub notifications.
2) Added DMUB HPD & HPD RX handling in dmub_srv_stat_get_notification().
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To enable dc links for USB4 DPIA ports and AUX command tunneling
for YELLOW_CARP_B0.
[HOW]
1) Created dc links for all USB4 DPIA ports in create_links().
dc_link_construct() implementation is split for legacy DDC and DPIAs.
As usb4 has no ddc, ddc->ddc_pin will be set to NULL for its dc link
and this parameter will be used to identify the dc links as DPIA. The
dc link for DPIA is further to be enhanced with implementation for link
encoder and link initialization.
2) usb4_dpia_count in struct resource_pool will be initialized to 4 in
dcn31_resource_construct() if the DCN is YELLOW_CARP_B0.
3) Enabled DMUB AUX via outbox for YELLOW_CARP_B0.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ind_block_64b_no_128bcl means INDEP_64B && INDEP_128B &&
MAX_COMPRESSED_BLOCK_SIZE == 64B. Only used by gfx10.3.
ind_block_64b means INDEP_64B && !INDEP_128B &&
MAX_COMPRESSED_BLOCK_SIZE == 64B. Only used by gfx9 and gfx10.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During DQE's promotion test, error appears in dmesg at boot
on dcn3.1;
[How]
Add NULL pointor check for the pointor to the amdgpu_dm_connector;
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Trying to enable multiple displays simultaneously exposed shortcomings
with the algorithm for dynamic link encoder assignment.
The main problems were:
- Assuming stream order remained constant across states would
sometimes lead to invalid DIG encoder assignment.
- Incorrect logic for deciding whether or not a DIG could support a
stream would also sometimes lead to invalid DIG encoder assignment.
- Changes in encoder assignment were wholesale while updating of the
pipe backend is incremental. This would lead to the hardware state
not matching the software state even with valid encoder assignments.
[How]
The following changes fix the identified problems.
- Use stream pointer rather than stream index to track streams across
states.
- Fix DIG compatibility check by examining the link signal type
rather than the stream signal type.
- Modify assignment algorithm to make incremental updates so software
and hardware states remain coherent.
Additionally:
- Add assertions and an encoder assignment validation
function link_enc_cfg_validate() to detect potential problems with
encoder assignment closer to their root cause.
- Reduce the frequency with which the assignment algorithm is
executed. It should not be necessary for fast state validation.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The codes to blank all dp display have been called many times,
so add a helper in dc_link to make it more concise.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
