Add a pair of tracepoints, one to track rxrpc_connection struct ref
counting and the other to track the client connection cache state.
Signed-off-by: David Howells <dhowells@redhat.com>
Add additional call tracepoint points for noting call-connected,
call-released and connection-failed events.
Also fix one tracepoint that was using an integer instead of the
corresponding enum value as the point type.
Signed-off-by: David Howells <dhowells@redhat.com>
Print a symbolic packet type name for each valid received packet in the
trace output, not just a number.
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the basic transmit DATA packet content size at 1412 bytes so that they
can be arbitrarily assembled into jumbo packets.
In the future, I'm thinking of moving to keeping a jumbo packet header at
the beginning of each packet in the Tx queue and creating the packet header
on the spot when kernel_sendmsg() is invoked. That way, jumbo packets can
be assembled on the spur of the moment for (re-)transmission.
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_send_call_packet() should use type in both its switch-statements
rather than using pkt->whdr.type. This might give the compiler an easier
job of uninitialised variable checking.
Signed-off-by: David Howells <dhowells@redhat.com>
Don't transmit an ACK if call->ackr_reason in unset. There's the
possibility of a race between recvmsg() sending an ACK and the background
processing thread trying to send the same one.
Signed-off-by: David Howells <dhowells@redhat.com>
Make the retransmission algorithm use for-loops instead of do-loops and
move the counter increments into the for-statement increment slots.
Though the do-loops are slighly more efficient since there will be at least
one pass through the each loop, the counter increments are harder to get
right as the continue-statements skip them.
Without this, if there are any positive acks within the loop, the do-loop
will cycle forever because the counter increment is never done.
Signed-off-by: David Howells <dhowells@redhat.com>
The soft-ACK parser doesn't increment the pointer into the soft-ACK list,
resulting in the first ACK/NACK value being applied to all the relevant
packets in the Tx queue. This has the potential to miss retransmissions
and cause excessive retransmissions.
Fix this by incrementing the pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
If the last call on a client connection is release after the connection has
had a bunch of calls allocated but before any DATA packets are sent (so
that it's not yet marked RXRPC_CONN_EXPOSED), an assertion will happen in
rxrpc_disconnect_client_call().
af_rxrpc: Assertion failed - 1(0x1) >= 2(0x2) is false
------------[ cut here ]------------
kernel BUG at ../net/rxrpc/conn_client.c:753!
This is because it's expecting the conn to have been exposed and to have 2
or more refs - but this isn't necessarily the case.
Simply remove the assertion. This allows the conn to be moved into the
inactive state and deleted if it isn't resurrected before the final put is
called.
Signed-off-by: David Howells <dhowells@redhat.com>
Call rxrpc_release_call() on getting an error in rxrpc_new_client_call()
rather than trying to do the cleanup ourselves. This isn't a problem,
provided we set RXRPC_CALL_HAS_USERID only if we actually add the call to
the calls tree as cleanup code fragments that would otherwise cause
problems are conditional.
Without this, we miss some of the cleanup.
Signed-off-by: David Howells <dhowells@redhat.com>
In rxrpc_put_one_client_conn(), if a connection has RXRPC_CONN_COUNTED set
on it, then it's accounted for in rxrpc_nr_client_conns and may be on
various lists - and this is cleaned up correctly.
However, if the connection doesn't have RXRPC_CONN_COUNTED set on it, then
the put routine returns rather than just skipping the extra bit of cleanup.
Fix this by making the extra bit of clean up conditional instead and always
killing off the connection.
This manifests itself as connections with a zero usage count hanging around
in /proc/net/rxrpc_conns because the connection allocated, but discarded,
due to a race with another process that set up a parallel connection, which
was then shared instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Purge the queue of to_be_accepted calls on socket release. Note that
purging sock_calls doesn't release the ref owned by to_be_accepted.
Probably the sock_calls list is redundant given a purges of the recvmsg_q,
the to_be_accepted queue and the calls tree.
Signed-off-by: David Howells <dhowells@redhat.com>
Record calls that need to be accepted using sk_acceptq_added() otherwise
the backlog counter goes negative because sk_acceptq_removed() is called.
This causes the preallocator to malfunction.
Calls that are preaccepted by AFS within the kernel aren't affected by
this.
Signed-off-by: David Howells <dhowells@redhat.com>
The code for determining the last packet in rxrpc_recvmsg_data() has been
using the RXRPC_CALL_RX_LAST flag to determine if the rx_top pointer points
to the last packet or not. This isn't a good idea, however, as the input
code may be running simultaneously on another CPU and that sets the flag
*before* updating the top pointer.
Fix this by the following means:
(1) Restrict the use of RXRPC_CALL_RX_LAST to the input routines only.
There's otherwise a synchronisation problem between detecting the flag
and checking tx_top. This could probably be dealt with by appropriate
application of memory barriers, but there's a simpler way.
(2) Set RXRPC_CALL_RX_LAST after setting rx_top.
(3) Make rxrpc_rotate_rx_window() consult the flags header field of the
DATA packet it's about to discard to see if that was the last packet.
Use this as the basis for ending the Rx phase. This shouldn't be a
problem because the recvmsg side of things is guaranteed to see the
packets in order.
(4) Make rxrpc_recvmsg_data() return 1 to indicate the end of the data if:
(a) the packet it has just processed is marked as RXRPC_LAST_PACKET
(b) the call's Rx phase has been ended.
Signed-off-by: David Howells <dhowells@redhat.com>
Move the check of rx_pkt_offset from rxrpc_locate_data() to the caller,
rxrpc_recvmsg_data(), so that it's more clear what's going on there.
Signed-off-by: David Howells <dhowells@redhat.com>
Add CONFIG_AF_RXRPC_IPV6 and make the IPv6 support code conditional on it.
This is then made conditional on CONFIG_IPV6.
Without this, the following can be seen:
net/built-in.o: In function `rxrpc_init_peer':
>> peer_object.c:(.text+0x18c3c8): undefined reference to `ip6_route_output_flags'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the 2-bytes Qualcomm tag that gigabit switches such as
the QCA8337/N might insert when receiving packets, or that we need
to insert while targeting specific switch ports. The tag is inserted
directly behind the ethernet header.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb replaces another one in ooo queue, I forgot to also
update tp->ooo_last_skb as well, if the replaced skb was the last one
in the queue.
To fix this, we simply can re-use the code that runs after an insertion,
trying to merge skbs at the right of current skb.
This not only fixes the bug, but also remove all small skbs that might
be a subset of the new one.
Example:
We receive segments 2001:3001, 4001:5001
Then we receive 2001:8001 : We should replace 2001:3001 with the big
skb, but also remove 4001:50001 from the queue to save space.
packetdrill test demonstrating the bug
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
+0.100 < . 1:1(0) ack 1 win 1024
+0 accept(3, ..., ...) = 4
+0.01 < . 1001:2001(1000) ack 1 win 1024
+0 > . 1:1(0) ack 1 <nop,nop, sack 1001:2001>
+0.01 < . 1001:3001(2000) ack 1 win 1024
+0 > . 1:1(0) ack 1 <nop,nop, sack 1001:2001 1001:3001>
Fixes: 9f5afeae51 ("tcp: use an RB tree for ooo receive queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=T1wh
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160913-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Support IPv6
Here is a set of patches that add IPv6 support. They need to be applied on
top of the just-posted miscellaneous fix patches. They are:
(1) Make autobinding of an unconnected socket work when sendmsg() is
called to initiate a client call.
(2) Don't specify the protocol when creating the client socket, but rather
take the default instead.
(3) Use rxrpc_extract_addr_from_skb() in a couple of places that were
doing the same thing manually. This allows the IPv6 address
extraction to be done in fewer places.
(4) Add IPv6 support. With this, calls can be made to IPv6 servers from
userspace AF_RXRPC programs; AFS, however, can't use IPv6 yet as the
RPC calls need to be upgradeable.
====================
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=vHfH
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160913-1' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Miscellaneous fixes
Here's a set of miscellaneous fix patches. There are a couple of points of
note:
(1) There is one non-fix patch that adjusts the call ref tracking
tracepoint to make kernel API-held refs on calls more obvious. This
is a prerequisite for the patch that fixes prealloc refcounting.
(2) The final patch alters how jumbo packets that partially exceed the
receive window are handled. Previously, space was being left in the
Rx buffer for them, but this significantly hurts performance as the Rx
window can't be increased to match the OpenAFS Tx window size.
Instead, the excess subpackets are discarded and an EXCEEDS_WINDOW ACK
is generated for the first. To avoid the problem of someone trying to
run the kernel out of space by feeding the kernel a series of
overlapping maximal jumbo packets, we stop allowing jumbo packets on a
call if we encounter more than three jumbo packets with duplicate or
excessive subpackets.
====================
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ovs kernel data path currently defers the execution of all
recirc actions until stack utilization is at a minimum.
This is too limiting for some packet forwarding scenarios due to
the small size of the deferred action FIFO (10 entries). For
example, broadcast traffic sent out more than 10 ports with
recirculation results in packet drops when the deferred action
FIFO becomes full, as reported here:
http://openvswitch.org/pipermail/dev/2016-March/067672.html
Since the current recursion depth is available (it is already tracked
by the exec_actions_level pcpu variable), we can use it to determine
whether to execute recirculation actions immediately (safe when
recursion depth is low) or defer execution until more stack space is
available.
With this change, the deferred action fifo size becomes a non-issue
for currently failing scenarios because it is no longer used when
there are three or fewer recursions through ovs_execute_actions().
Suggested-by: Pravin Shelar <pshelar@ovn.org>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c3f8324188 "net: Add full IPv6 addresses to flow_keys" added an
unused instance of struct flow_dissector_key_addrs into struct fl_flow_key,
remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the definitions for src/dst udp/tcp port masks and use
them when setting && dumping the relevant keys.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action is intended to be an upgrade from a usability perspective
from pedit (as well as operational debugability).
Compare this:
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action pedit munge offset -14 u8 set 0x02 \
munge offset -13 u8 set 0x15 \
munge offset -12 u8 set 0x15 \
munge offset -11 u8 set 0x15 \
munge offset -10 u16 set 0x1515 \
pipe
to:
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbmod dmac 02:15:15:15:15:15
Also try to do a MAC address swap with pedit or worse
try to debug a policy with destination mac, source mac and
etherype. Then make few rules out of those and you'll get my point.
In the future common use cases on pedit can be migrated to this action
(as an example different fields in ip v4/6, transports like tcp/udp/sctp
etc). For this first cut, this allows modifying basic ethernet header.
The most important ethernet use case at the moment is when redirecting or
mirroring packets to a remote machine. The dst mac address needs a re-write
so that it doesnt get dropped or confuse an interconnecting (learning) switch
or dropped by a target machine (which looks at the dst mac). And at times
when flipping back the packet a swap of the MAC addresses is needed.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a small skb_at_tc_ingress() helper for testing for ingress, so
make use of it. cls_bpf already uses it and so should act_bpf.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_mac_header_was_set() test in cls_bpf's and act_bpf's fast-path is
actually unnecessary and can be removed altogether. This was added by
commit a166151cbe ("bpf: fix bpf helpers to use skb->mac_header relative
offsets"), which was later on improved by 3431205e03 ("bpf: make programs
see skb->data == L2 for ingress and egress"). We're always guaranteed to
have valid mac header at the time we invoke cls_bpf_classify() or tcf_bpf().
Reason is that since 6d1ccff627 ("net: reset mac header in dev_start_xmit()")
we do skb_reset_mac_header() in __dev_queue_xmit() before we could call
into sch_handle_egress() or any subsequent enqueue. sch_handle_ingress()
always sees a valid mac header as well (things like skb_reset_mac_len()
would badly fail otherwise). Thus, drop the unnecessary test in classifier
and action case.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rcu_read_lock protection from tunnel_key_dump and use
rtnl_dereference, dump operation is protected by rtnl lock.
Also, remove rcu_read_lock from tunnel_key_release and use
rcu_dereference_protected.
Both operations are running exclusively and a writer couldn't modify
t->params while those functions are executed.
Fixes: 54d94fd89d90 ('net/sched: Introduce act_tunnel_key')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 support to AF_RXRPC. With this, AF_RXRPC sockets can be created:
service = socket(AF_RXRPC, SOCK_DGRAM, PF_INET6);
instead of:
service = socket(AF_RXRPC, SOCK_DGRAM, PF_INET);
The AFS filesystem doesn't support IPv6 at the moment, though, since that
requires upgrades to some of the RPC calls.
Note that a good portion of this patch is replacing "%pI4:%u" in print
statements with "%pISpc" which is able to handle both protocols and print
the port.
Signed-off-by: David Howells <dhowells@redhat.com>
There are two places that want to transmit a packet in response to one just
received and manually pick the address to reply to out of the sk_buff.
Make them use rxrpc_extract_addr_from_skb() instead so that IPv6 is handled
automatically.
Signed-off-by: David Howells <dhowells@redhat.com>
Create an address for sendmsg() to bind unbound socket with rather than
using a completely blank address otherwise the transport socket creation
will fail because it will try to use address family 0.
We use the address family specified in the protocol argument when the
AF_RXRPC socket was created and SOCK_DGRAM as the default. For anything
else, bind() must be used.
Signed-off-by: David Howells <dhowells@redhat.com>
call->rx_winsize should be initialised to the sysctl setting and the sysctl
setting should be limited to the maximum we want to permit. Further, we
need to place this in the ACK info instead of the sysctl setting.
Furthermore, discard the idea of accepting the subpackets of a jumbo packet
that lie beyond the receive window when the first packet of the jumbo is
within the window. Just discard the excess subpackets instead. This
allows the receive window to be opened up right to the buffer size less one
for the dead slot.
Signed-off-by: David Howells <dhowells@redhat.com>
The preallocated call buffer holds a ref on the calls within that buffer.
The ref was being released in the wrong place - it worked okay for incoming
calls to the AFS cache manager service, but doesn't work right for incoming
calls to a userspace service.
Instead of releasing an extra ref service calls in rxrpc_release_call(),
the ref needs to be released during the acceptance/rejectance process. To
this end:
(1) The prealloc ref is now normally released during
rxrpc_new_incoming_call().
(2) For preallocated kernel API calls, the kernel API's ref needs to be
released when the call is discarded on socket close.
(3) We shouldn't take a second ref in rxrpc_accept_call().
(4) rxrpc_recvmsg_new_call() needs to get a ref of its own when it adds
the call to the to_be_accepted socket queue.
In doing (4) above, we would prefer not to put the call's refcount down to
0 as that entails doing cleanup in softirq context, but it's unlikely as
there are several refs held elsewhere, at least one of which must be put by
someone in process context calling rxrpc_release_call(). However, it's not
a problem if we do have to do that.
Signed-off-by: David Howells <dhowells@redhat.com>
Adjust the call ref tracepoint to show references held on a call by the
kernel API separately as much as possible and add an additional trace to at
the allocation point from the preallocation buffer for an incoming call.
Note that this doesn't show the allocation of a client call for the kernel
separately at the moment.
Signed-off-by: David Howells <dhowells@redhat.com>
Allow tx_winsize to grow when the ACK info packet shows a larger receive
window at the other end rather than only permitting it to shrink.
Signed-off-by: David Howells <dhowells@redhat.com>
skb->len should be used rather than skb->data_len when referring to the
amount of data in a packet. This will only cause a malfunction in the
following cases:
(1) We receive a jumbo packet (validation and splitting both are wrong).
(2) We see if there's extra ACK info in an ACK packet (we think it's not
there and just ignore it).
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_recvmsg() needs to make sure that the call it has just been
processing gets requeued for further attention if the buffer has been
filled and there's more data to be consumed. The softirq producer only
queues the call and wakes the socket if it fills the first slot in the
window, so userspace might end up sleeping forever otherwise, despite there
being data available.
This is not a problem provided the userspace buffer is big enough or it
empties the buffer completely before more data comes in.
Signed-off-by: David Howells <dhowells@redhat.com>
We need to wake up the sender when Tx window rotation due to an incoming
ACK makes space in the buffer otherwise the sender is liable to just hang
endlessly.
This problem isn't noticeable if the Tx phase transfers no more than will
fit in a single window or the Tx window rotates fast enough that it doesn't
get full.
Signed-off-by: David Howells <dhowells@redhat.com>
Peer records created for incoming connections weren't getting their hash
key set. This meant that incoming calls wouldn't see more than one DATA
packet - which is not a problem for AFS CM calls with small request data
blobs.
Signed-off-by: David Howells <dhowells@redhat.com>
'ub' is malloced in tipc_udp_enable() and should be freed before
leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ba5aa84a2d ("tipc: split UDP nl address parsing")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If /sbin/bridge-stp is available on the system, bridge tries to execute
it instead of the kernel implementation when starting/stopping STP.
If anything goes wrong with /sbin/bridge-stp, bridge silently falls back
to kernel STP, making hard to debug userspace STP.
This patch adds a br_stp_call_user helper to start/stop userspace STP
and debug errors from the program: abnormal exit status is stored in the
lower byte and normal exit status is stored in higher byte.
Below is a simple example on a kernel with dynamic debug enabled:
# ln -s /bin/false /sbin/bridge-stp
# brctl stp br0 on
br0: failed to start userspace STP (256)
# dmesg
br0: /sbin/bridge-stp exited with code 1
br0: failed to start userspace STP (256)
br0: using kernel STP
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Mostly small sets of driver fixes scattered all over the place.
1) Mediatek driver fixes from Sean Wang. Forward port not written
correctly during TX map, missed handling of EPROBE_DEFER, and
mistaken use of put_page() instead of skb_free_frag().
2) Fix socket double-free in KCM code, from WANG Cong.
3) QED driver fixes from Sudarsana Reddy Kalluru, including a fix for
using the dcbx buffers before initializing them.
4) Mellanox Switch driver fixes from Jiri Pirko, including a fix for
double fib removals and an error handling fix in
mlxsw_sp_module_init().
5) Fix kernel panic when enabling LLDP in i40e driver, from Dave
Ertman.
6) Fix padding of TSO packets in thunderx driver, from Sunil Goutham.
7) TCP's rcv_wup not initialized properly when using fastopen, from
Neal Cardwell.
8) Don't use uninitialized flow keys in flow dissector, from Gao
Feng.
9) Use after free in l2tp module unload, from Sabrina Dubroca.
10) Fix interrupt registry ordering issues in smsc911x driver, from
Jeremy Linton.
11) Fix crashes in bonding having to do with enslaving and rx_handler,
from Mahesh Bandewar.
12) AF_UNIX deadlock fixes from Linus.
13) In mlx5 driver, don't read skb->xmit_mode after it might have been
freed from the TX reclaim path. From Tariq Toukan.
14) Fix a bug from 2015 in TCP Yeah where the congestion window does
not increase, from Artem Germanov.
15) Don't pad frames on receive in NFP driver, from Jakub Kicinski.
16) Fix chunk fragmenting in SCTP wrt. GSO, from Marcelo Ricardo
Leitner.
17) Fix deletion of VRF routes, from Mark Tomlinson.
18) Fix device refcount leak when DAD fails in ipv6, from Wei Yongjun"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
net/mlx4_en: Fix panic on xmit while port is down
net/mlx4_en: Fixes for DCBX
net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_state()
net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_all()
net: ethernet: renesas: sh_eth: add POST registers for rz
drivers: net: phy: mdio-xgene: Add hardware dependency
dwc_eth_qos: do not register semi-initialized device
sctp: identify chunks that need to be fragmented at IP level
mlxsw: spectrum: Set port type before setting its address
mlxsw: spectrum_router: Fix error path in mlxsw_sp_router_init
nfp: don't pad frames on receive
nfp: drop support for old firmware ABIs
nfp: remove linux/version.h includes
tcp: cwnd does not increase in TCP YeAH
net/mlx5e: Fix parsing of vlan packets when updating lro header
net/mlx5e: Fix global PFC counters replication
net/mlx5e: Prevent casting overflow
net/mlx5e: Move an_disable_cap bit to a new position
net/mlx5e: Fix xmit_more counter race issue
tcp: fastopen: avoid negative sk_forward_alloc
...
A previous patch added l3mdev flow update making these hooks
redundant. Remove them.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
