The old code only handled either 6bpc or 8bpc. Since it's easy to do,
reorganize the code to be a bit more generic so that it can also handle
10bpc and 12bpc. Note that we still start with 8bpc, so there's no
functional change.
Also, since we no don't need to compute the 6BPC flag in the mode_valid
callback, we can consolidate things a bit. That requires though that
the link bw computation is moved up in the compute_config callback.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The procedure has now 3 steps:
1. Compute the bpp that the plane will output, this is done in
pipe_config_set_bpp and stored into pipe_config->pipe_bpp. Also,
this function clamps the pipe_bpp to whatever limit the EDID of any
connected output specifies.
2. Adjust the pipe_bpp in the encoder and crtc functions, according to
whatever constraints there are.
3. Decide whether to use dither by comparing the stored plane bpp with
computed pipe_bpp.
There are a few slight functional changes in this patch:
- LVDS connector are now also going through the EDID clamping. But in
a 2nd change we now unconditionally force the lvds bpc value - this
shouldn't matter in reality when the panel setup is consistent, but
better safe than sorry.
- HDMI now forces the pipe_bpp to the selected value - I think that's
what we actually want, since otherwise at least the pixelclock
computations are wrong (I'm not sure whether the port would accept
e.g. 10 bpc when in 12bpc mode). Contrary to the old code, we pick
the next higher bpc value, since otherwise there's no way to make
use of the 12 bpc mode (since the next patch will remove the 12bpc
plane format, it doesn't exist).
Both of these changes are due to the removal of the
pipe_bpp = min(display_bpp, plane_bpp);
statement.
Another slight change is the reworking of the dp bpc code:
- For the mode_valid callback it's sufficient to only check whether
the mode would fit at the lowest bpc.
- The bandwidth computation code is a bit restructured: It now walks
all available bpp values in an outer loop and the codeblock that
computes derived values (once a good configuration is found) has been
moved out of the for loop maze. This is prep work to allow us to
successively fall back on bpc values, and also correctly support bpc
values != 8 or 6.
v2: Rebased on top of Paulo Zanoni's little refactoring to use more
drm dp helper functions.
v3: Rebased on top of Jani's eDP bpp fix and Ville's limited color
range work.
v4: Remove the INTEL_MODE_DP_FORCE_6BPC #define, no longer needed.
v5: Remove intel_crtc->bpp, too, and fix up the 12bpc check in the
hdmi code. Also fixup the bpp check in intel_dp.c, it'll get reworked
in a later patch though again.
v6: Fix spelling in a comment.
v7: Debug output improvements for the bpp computation.
v8: Fixup 6bpc lvds check - dual-link and 8bpc mode are different
things!
v9: Reinstate the fix to properly ignore the firmware edp bpp ... this
was lost in a rebase.
v10: Both g4x and vlv lack 12bpc pipes, so don't enforce that we have
that. Still unsure whether this is the way to go, but at least 6bpc
for a 8bpc hdmi output seems to work.
v11: And g4x/vlv also lack 12bpc hdmi support, so only support high
depth on DP. Adjust the code.
v12: Rebased.
v13: Split out the introduction of pipe_config->dither|pipe_bpp, as
requested from Jesse Barnes.
v14: Split out the special 6BPC handling for DP, as requested by Jesse
Barnes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to compute this earlier. To avoid a big complicated patch,
this patch here just does the big search&replace and still calls the
old functions at the same places.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have a useful struct for this, let's use it. Some neat
pointer-chasing required, but it's all there already.
v2: Rebased on top of the added Haswell limited color range support.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is used way too often in the enable/disable paths. And will
be even more useful in the future.
Note that correct semantics of this change highly depend upon
correct updating of intel_crtc->config: Like with all other
modeset state, we need to call ->disable with the old config,
but ->mode_set and ->enable with the new config.
v2: Do not yet use the flag in the ->disable callbacks - atm we don't
yet have support for the information stored in the pipe_config in the
hw state readout code, so this will be wrong at boot-up/resume.
v3: Rebased on top of the hdmi/dp ddi encoder merging.
v4: Fixup stupid rebase error which lead to a NULL vfunc deref.
v5: On haswell the VGA port is on the PCH!
v6: s/IS_HASWELL/HAS_DDI/, spotted by Paulo Zanoni. Also add a missing
parameter name in a function declaration.
v7: Don't forget to git add ...
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Used by SDVO (and hopefully, eventually HDMI, if we ever get around
to fixing up the low dotclock CEA modes ...).
This required adding a new encoder->mode_set callback to be able to
pass around the intel_crtc_config.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only used by the lvds encoder. Note that we shouldn't do the same
simple conversion with the FORCE_6BPC flag, since that's much better
handled by moving all the pipe_bpc computation around.
This requires that we pass the pipe config around to encoders, so
that they can set special attributes and set constraints. To do so
introduce a new ->compute_config encoder callback, which is called in
stead of the drm crtc helper's ->mode_fixup.
To avoid massive churn all over the codebase we don't want to convert
all existing ->mode_fixup functions. Instead I've opted to convert
them on an as-needed basis (mostly to cut down on rebase conflicts and
to have more freedom to experiment around while developing the
patches).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To make decent modeset state checking possible (e.g. for the check
mode with atomic modesetting) we want to have the full pipe
configuration and state checks done before we touch the hw.
To ensure that all the little bits&pieces that are now moved to the
pipe_config handle this correctly, move its computation to the right
spot now, before we touch the hw in the disable_pipes step.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently only containing the requested and the adjusted mode. And
only crtc callbacks are converted somewhat to it, encoders will be
done on a as-needed basis (simply too much churn in one patch
otherwise).
Future patches will add tons more useful stuff to this struct,
starting with the very simple.
v2: Store the pipe_config in the intel_crtc, so that the ->mode-set,
->enable and also ->disable have easy access to it.
v3: Store the pipe config in the right crtc ...
v4: Rebased.
v5: Fixup an OOPS when trying to kfree an ERR_PTR.
v6: Used drm_moode_copy and some other small cleanups as suggested
by Ville Syrjälä.
v7: drm_mode_copy preserves the mode id of the destination, so no need
to clear it again (Ville).
v8: Break a long line spotted by Paulo.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From the w/a database:
'To prevent false VT-d type 6 error:
The primary display plane must be 256KiB aligned, and require an extra
128 PTEs of padding afterward;
The sprites planes must be 128KiB aligned, and require an extra 64 PTEs
of padding afterward;
The cursors must be 64KiB aligned, and require an extra 2 PTEs of
padding afterward.'
As we use the same function to pin the primary and sprite planes, we can
simply use the more strict requirements for scanouts for both.
Instead of using explicit padding PTEs following the scanout objects, we
should be able to use the scratch page that is always mapped into the
unused PTEs to avoid the VT-d error.
References: https://bugs.freedesktop.org/show_bug.cgi?id=59626
References: https://bugs.freedesktop.org/show_bug.cgi?id=59627
References: https://bugs.freedesktop.org/show_bug.cgi?id=59631
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Apply s/vtd_wa/vtd_scanout_wa/ bikeshed since Damien likes
it, too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needed for VT switchless resume.
v2: cursor state is now handled correctly in crtc_enable (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So don't read it when capturing the error state. This solves some
"unclaimed register" messages on Haswell when we hang the GPU.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The first version of commit "drm/i915: there's no DSPADDR register on
Haswell" added 2 "!IS_HASWELL" checks. When reviewing the patch, Ben
suggested to make these checks more future-proof, so when Daniel
applied the patch he fixed the first check but not the second. This
commit makes the second check also "future-proof".
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We are really talking about the transcoder function here and the disable
version uses trancoder in its name already, so let's try to be
consistent.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the case where the hardware has been wrongly programmed and the EDP
TRANS_DDI_FUNC_CTL register has a bogus value in its EDP Input field, we
were using the pipe variable uninitialized.
In this case, shutdown the transcoder. It will be programmed correctly
the next time we try to enabled eDP.
Note from Paulo's review: Wrong modeset sequence can easily lead to
frozen machines hence the disable_ddi call might be risky. But since
things are awry already, doesn't matter too much.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add note about Paulo's caution about potential hangs.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This comment looks like some historical leftover. Get rid of it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Port C is for eDP. Port B is shared between HDMI and DP.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Planes are fixed to pipes in VLV.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into drm-intel-next-queued
Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in
commit a321e91b6d
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 27 17:02:56 2013 -0800
lib/scatterlist: add simple page iterator
The merge itself is just two trivial conflicts:
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So don't read it when we hang the GPU. This solves "unclaimed
register" messages.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Future-proof by adding a gen >= 7 check in addition to the
!IS_HSW check from Paulo's original patch, suggested by Ben.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So don't read it when capturing the error state. This solves some
"unclaimed register" messages on Haswell when we hang the GPU.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This solves some "unclaimed register" messages when there's a GPU hang
on Haswell.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add missing IS_VLV check as spotted by Ville Syrjälä.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bunch of fixes, nothing truely horrible:
- Fix PCH irq handling race which resulted in missed gmbus/dp aux irqs
and subsequent fallout (Paulo)
- Fixup off-by-one in our hsw id table (Kenneth)
- Fixup ilk rc6 support (disabled by default), regression introduced in
3.8
- g4x plane w/a from Egbert Eich
- gen2/3/4 dpms suspend/standy fixes for VGA outputs from Patrik Jakobsson
- Workaround dying ivb machines with less aggressive rc6 values (Stéphane
Marchesin)
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Turn off hsync and vsync on ADPA when disabling crt
drm/i915: Fix incorrect definition of ADPA HSYNC and VSYNC bits
drm/i915: also disable south interrupts when handling them
drm/i915: enable irqs earlier when resuming
drm/i915: Increase the RC6p threshold.
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
drm/i915: Fix Haswell/CRW PCI IDs.
drm/i915: Don't clobber crtc->fb when queue_flip fails
drm/i915: wait_event_timeout's timeout is in jiffies
drm/i915: Fix missing variable initilization
Some HDMI registers can be used for SDVO, so saying "HDMIB" should be
the same as saying "SDVOB" for a given HW generation. This was not
true and led to confusions and even a regression.
Previously we had:
- SDVO{B,C} defined as the Gen3+ registers
- HDMI{B,C,D} and PCH_SDVOB defined as the PCH registers
But now:
- SDVO{B,C} became GEN3_SDVO{B,C} on SDVO code
- SDVO{B,C} became GEN4_HDMI{B,C} on HDMI code
- HDMI{B,C,D} became PCH_HDMI{B,C,D}
- PCH_SDVOB is still the same thing
v2: Rebase (v1 was sent in May 2012).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On G45 some low res modes (800x600 and 1024x768) produce a blank
screen when the display plane is enabled with with cursor plane
off.
Experiments showed that this issue occurred when the following
conditions were met:
a. a previous mode had the cursor plane enabled (Xserver).
b. this mode or the previous one was using self refresh. (Thus
the problem was only seen with low res modes).
The screens lit up as soon as the cursor plane got enabled.
Therefore the blank screen occurred only in console mode, not
when running an Xserver.
It also seemed to be necessary to disable self refresh while briefly
enabling the cursor plane.
Signed-off-by: Egbert Eich <eich@suse.com>
Bugzilla: https://bugs.freedesktop.org/attachment.cgi?bugid=61457
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: drop spurious whitespace change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code is totally obvious so these comments serve no purpose. What's
worse, one of them was wrong. Just remove them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The load detection code has moved around at some point, but it left
a comment behind. The code now looks to be different enough to make
the comment stale as well. Just remove it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The proper use of find_pll() isn't always so easy to determine from the
code itself. Some documentation should help.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Restore crtc->fb to the old framebuffer if queue_flip fails.
While at it, kill the pointless intel_fb temp variable.
v2: Update crtc->fb before queue_flip and restore it back
after a failure.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So ditch that if clause from the i8xx pll update code.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two regressions fixes from snowboarding land
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Revert hdmi HDP pin checks
drm/i915: Handle untiled planes when computing their offsets
We trim the fb to fit the CRTC by computing the offset of that CRTC to
its nearest tile_row origin. This allows us to use framebuffers that are
larger than the CRTC limits without additional work.
However, we failed to compute the offset for a linear framebuffer
correctly as we treated its x-advance in whole tiles (instead of the
linear increment expected), leaving the CRTC misaligned with its
contents.
Fixes regression from commit c2c7513124
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 5 12:17:30 2012 +0200
drm/i915: adjust framebuffer base address on gen4+
v2: Adjust relative x-coordinate after linear alignment (vsyrjala)
v3: Repaint with pokadots (vsyrjala)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61152
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's my promised pile of fixes for 3.9. I've dropped the core prep
patches for vt-switchless suspend/resume as discussed on irc. Highlights:
- Fix dmar on g4x. Not really gfx related, but I'm fed up with getting
blamed for dmar crapouts.
- Disable wc ptes updates on ilk when dmar is enabled (Chris). So again,
dmar, but this time gfx related :(
- Reduced range support for hsw, using the pipe CSC (Ville).
- Fixup pll limits for gen3/4 (Patrick Jakobsson). The sdvo patch is
already confirmed to fix 2 bug reports, so added cc: stable on that one.
- Regression fix for 8bit fb console (Ville).
- Preserve lane reversal bits on DDI/FDI ports (Damien).
- Page flip vs. gpu hang fixes (Ville). Unfortuntely not quite all of
them, need to decide what to do with the currently still in-flight ones.
- Panel fitter regression fix from Mika Kuoppala (was accidentally left on
on some pipes with the new modset code since 3.7). This also improves
the modeset sequence and might help a few other unrelated issues with
lvds.
- Write backlight regs even harder ... another installement in our eternal
fight against the BIOS and backlights.
- Fixup lid notifier vs. suspend/resume races (Zhang Rui). Prep work for
new ACPI stuff, but closing the race itself seems worthwile on its own.
- A few other small fixes and tiny cleanups all over.
Lots of the patches are cc: stable since I've stalled on a few
not-so-important fixes for 3.8 due to the grumpy noise Linus made.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (33 commits)
intel/iommu: force writebuffer-flush quirk on Gen 4 Chipsets
drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK
drm/i915: Implement pipe CSC based limited range RGB output
drm/i915: inverted brightness quirk for Acer Aspire 4736Z
drm/i915: Print the hw context status is debugfs
drm/i915: Use HAS_L3_GPU_CACHE in i915_gem_l3_remap
drm/i915: Fix PIPE_CONTROL DW/QW write through global GTT on IVB+
drm/i915: Set i9xx sdvo clock limits according to specifications
drm/i915: Set i9xx lvds clock limits according to specifications
drm/i915: Preserve the DDI link reversal configuration
drm/i915: Preserve the FDI line reversal override bit on CPT
drm/i915: add missing \n to UTS_RELEASE in the error_state
drm: Use C8 instead of RGB332 when determining the format from depth/bpp
drm: Fill depth/bits_per_pixel for C8 format
drm/i915: don't clflush gem objects in stolen memory
drm/i915: Don't wait for page flips if there was GPU reset
drm/i915: Kill obj->pending_flip
drm/i915: Fix a typo in a intel_modeset_stage_output_state() comment
drm/i915: remove bogus mutex_unlock from error-path
drm/i915: Print the pipe control page GTT address
...
GPU reset will drop all flips that are still in the ring. So after the
reset, call update_plane() for all CRTCs to make sure the primary
planes are scanning out from the correct buffer.
Also finish all pending flips. That means user space will get its
page flip events and won't get stuck waiting for them.
v2: Explicitly finish page flips instead of relying on FLIP_DONE
interrupt being generated by the base address update.
v3: Make two loops over crtcs to avoid deadlocks with the crtc mutex
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup long line complaint from checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since obj->pending_flips was never set, intel_pipe_set_base() never
actually waited for pending page flips to complete.
We really do want to wait for the pending flips, because otherwise the
mmio surface base address update could overtake the flip, and you
could end up with an old frame on the screen once the flip really
completes.
Just call intel_crtc_wait_pending_flips() prior to calling
intel_pipe_set_base() instead of calling just intel_finish_fb()
from intel_pipe_set_base(). Moving the call outside of
intel_pipe_set_base() avoids calling it twice from the full
modeset path.
v2: Wait for pending flips w/o holding struct_mutex
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HSW no longer has the PIPECONF bit for limited range RGB output.
Instead the pipe CSC unit must be used to perform that task.
The CSC pre offset are set to 0, since the incoming data is full
[0:255] range RGB, the coefficients are programmed to compress the
data into [0:219] range, and then we use either the CSC_MODE black
screen offset bit, or the CSC post offsets to shift the data to
the correct [16:235] range.
Also have to change the confiuration of all planes so that the
data is sent through the pipe CSC unit. For simplicity send the
plane data through the pipe CSC unit always, and in case full
range output is requested, the pipe CSC unit is set up with an
identity transform to pass the plane data through unchanged.
I've been told by some hardware people that the use of the pipe
CSC unit shouldn't result in any measurable increase in power
consumption numbers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Intel PRM says the M1 and M2 divisors must be in the range of 10-20 and 5-9.
Since we do all calculations based on them being register values (which are
subtracted by 2) we need to specify them accordingly.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56359
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Intel PRM says the M1 and M2 divisors must be in the range of 10-20 and 5-9.
Since we do all calculations based on them being register values (which are
subtracted by 2) we need to specify them accordingly.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a GPU reset occurs while a page flip has been submitted to the ring,
the flip will never complete once the ring has been reset.
The GPU reset can be detected by sampling the reset_counter before the
flip is submitted, and then while waiting for the flip, the sampled
counter is compared with the current reset_counter value.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Move the reset_counter assignment to an earlier place in
common code as discussed on the mailing list.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60140
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pending flip mask no longer set anywhere, so trying to wait for
while it's non-zero is a no-op. Remove it completely.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the previous patch "drm/i915: disable shared panel fitter for
pipe" we now disable the panel fitter at the right spot in the modeset
sequence in the crtc functions on all platforms. Hence the disabling
in intel_disable_lvds is no longer required and potentially harmful
(since the plane is still enabled at this point).
Similarly on the enabling side we enable the panel fitter in the lvds
callback only once the plane is enabled. Which is too late. Hence move
this into a new intel_pre_enable_lvds callback.
Finally we can ditch lvds_encoder->pfit_dirty - this was required to
work around the crtc helper semantics, but with the new i915 modeset
infrastructure we should enable/disable the pfit only when enabling or
disabling the entire output pipeline. So separate state tracking for
the pfit is no longer required.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Bikeshed the commit message a bit to stress that now we
enable/disable the pfit on i9xx platforms at the right point of time
compared to the old code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If encoder is switched off by BIOS, but the panel fitter is left on,
we never try to turn off the panel fitter and leave it still attached
to the pipe - which can cause blurry output elsewhere.
Based on work by Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58867
Cc: stable@vger.kernel.org
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: Andreas Sturmlechner <andreas.sturmlechner@gmail.com>
[danvet: Remove the redundant HAS_PCH_SPLIT check and add a tiny
comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While doing the modeset rework for drm/i915 I've noticed that the fb
helper is very liberal with the semantics of the ->set_config
interface:
- It doesn't bother clearing stale modes (e.g. when unplugging a
screen).
- It unconditionally sets the fb, even if no mode will be set on a
given crtc.
- The initial setup is a bit fun since we need to pick crtcs to decide
the desired fb size, but also should set the modeset->fb pointer.
Explain what's going on in the fixup code after the fb is allocated.
The crtc helper didn't really care, but the new i915 modeset
infrastructure did, so I've had to add a bunch of special-cases to
catch this.
Fix this all up and enforce the interface by converting the checks in
drm/i915/intel_display.c to BUG_ONs.
v2: Fix commit message spell fail spotted by Rob Clark.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the driver is in control of whether it needs to disable
everything at take-over or not, we can rip this all out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
"Probably the last feature pull for 3.9, there's some fixes outstanding
thought that I'd like to sneak in. And maybe 3.8 takes a bit longer ...
Anyway, highlights of this pull:
- Kill the horrible IS_DISPLAYREG hack to handle the mmio offset movements
on vlv, big thanks to Ville.
- Dynamic power well support for Haswell, shaves away a bit when only
using the eDP port on pipe A (Paulo). Plus unclaimed register fixes
uncovered by this.
- Clarifications of the gpu hang/reset state transitions, hopefully fixing
a few spurious -EIO deaths in userspace.
- Haswell ELD fixes.
- Some more (pp)gtt cleanups from Ben.
- A few smaller things all over.
Plus all the stuff from the previous rather small pull request:
- Broadcast RBG improvements and reduced color range fixes from Ville.
- Ben is on a "kill legacy gtt code for good" spree, first pile of patches
included.
- No-relocs and bo lut improvements for faster execbuf from Chris.
- Some refactorings from Imre."
* tag 'drm-intel-next-2013-02-01' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
GPU/i915: Fix acpi_bus_get_device() check in drivers/gpu/drm/i915/intel_opregion.c
drm/i915: Set the SR01 "screen off" bit in i915_redisable_vga() too
drm/i915: Kill IS_DISPLAYREG()
drm/i915: Introduce i915_vgacntrl_reg()
drm/i915: gen6_gmch_remove can be static
drm/i915: dynamic Haswell display power well support
drm/i915: check the power down well on assert_pipe()
drm/i915: don't send DP "idle" pattern before "normal" on HSW PORT_A
drm/i915: don't run hsw power well code on !hsw
drm/i915: kill cargo-culted locking from power well code
drm/i915: Only run idle processing from i915_gem_retire_requests_worker
drm/i915: Fix CAGF for HSW
drm/i915: Reclaim GTT space for failed PPGTT
drm/i915: remove intel_gtt structure
drm/i915: Add probe and remove to the gtt ops
drm/i915: extract hw ppgtt setup/cleanup code
drm/i915: pte_encode is gen6+
drm/i915: vfuncs for ppgtt
drm/i915: vfuncs for gtt_clear_range/insert_entries
drm/i915: Error state should print /sys/kernel/debug
...
