All scans are using the unified APIs now, so using "unified" in the
symbols is useless and just make them much longer and the main
difference between scans now is LMAC vs. UMAC. Remove "unified" from
all relevant symbols.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of hardcoding the differences between UMAC scans and LMAC
scans (which in this case is the number of simultaneous scans that can
run), introduce a max_scans variable and stop scans of the other type
(i.e. stop sched scan if regular scan is being attempted and
vice-versa) if the number of running scans reached the maximum.
Add a function that checks if the maximum number of scans was reached
and stops the appropriate scan to make room for the new scan.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
LMAC scans cannot handle more than one scan at a time, but UMAC scans
can. To avoid confusion we should combine the states of these two
types of scans. To do so, we need to support mutliple scans at the
same time for UMAC.
This commit changes the scan_status element from a single value to a
bitmask of running scan types for LMAC. Later, we will modify UMAC
scans to use the same state bitmask.
Additionally, add stopping scan flags for scheduled and regular scans.
This makes it easier to differentiate and handle stop requests
triggered by the driver and spontaneous stops generated by the
firmware.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some cases, max_out_time value is smaller than 200 and having the
NL80211_SCAN_FLAG_LOW_PRIORITY flag was actually causing the
max_out_time to be increased. To avoid that, set max_out_time to 200
only if it's greater than 200.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add scan parameters information to make it easier to debug scan dwell
times and fragmentation.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Scan iteration complete notification handling uses the wrong FW API
version (version 2 instead of version 3).
Fix that by removing version 2 API which is no longer used, and using
only the updated version.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the reset flow, the driver cancels ongoing scan and sends scan
complete notification to mac80211. However it does not clean its UID.
Add cleaning scan UID for the ongoing scan. Loop over all other UIDs
to make sure there's nothing left there and warn if any is found.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for delaying the start of a scheduled scan (or a WoWLAN
net-detect scan).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In nic restart flow we inform mac80211 that scan was aborted, but it was
based only on scan_status which is not set by UMAC scan. Fix that.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently scan params structure has only active or passive dwell time
fields, passive one is used for fragmented scans too. FW needs the
passive dwell time even when performing fragmented scan for calculating
time between channels. Add a separate parameter for fragmented dwell time
and pass both fragmented and passive to FW.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
20 ms fragments are no longer required by system.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The legacy scan API is deprecated and not used anymore with 10 and
higher firmware versions. Since we deprecated firmware version 9, we
can remove a whole lot of unused code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A scan abort command failure is not that unusual, since we may try to
send it after the scan has actually completed but before we received
the completed notification from the firmware. The scan abort can also
fail for other reasons, such as a timeout. In such cases, we should
clear things up so the next scans will work again. To do so, don't
return immediately in case of failures, but call
ieee80211_scan_completed() and clear the scan_status flags.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use the chanel hw_value and not the center frequency when
building channel array for scan_config_cmd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable EBS on one shot scans if supported by FW.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Last EBS status wasn't set to success in the initialization, which
caused the first scan to be without EBS. Fix that.
When EBS is not enabled by the driver, the FW still sends ebs_status success,
which can override EBS failure state. Consider only EBS failures, to avoid
such override. Last_ebs_success is set back to true upon disconnection.
Last_ebs_success wasn't set in umac scan abort flow, fix that too.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.
This fix is needed to fix few bugs regarding scans that take too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fragmented scan should be applied for all channels, passive and active.
When scanning on passive channels the firmware uses frag_passive_dwell
to define the maximum continuous scan time before returning to the
operating channel. On active channels max_out_time is the parameter
used by the firmware to define the maximum time allowed out of the
operating channel. Since active channels' scan should also be fragmented
set max_out_time equal to frag_passive_dwell.
In addition:
- Set max_out_time and suspend_time if the firmware doesn't support
fragmented scan to avoid unexpected behavior.
- Adjust max_out_time for second level of scan precedence.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This option enables scan offload iteration complete notification from
firmware which includes the last iteration's status and the scanned
channels from the current iteration.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we have an active scheduled scan, and the RFKILL
interrupt kicks in, the stack will cancel the scheduled
scan as part of the down flow. But cancelling scheduled
scan usually implies sending a command to the firwmare
which has been killed as part of the RFKILL interrupt
handling.
Because of that, we returned an error to mac80211 when
it asked to stop the scheduled scan and didn't notify the
end of the scheduled scan. Besides a fat warning, this led
to a situation in which cfg80211 would refuse any new scan
request.
To disentangle this, fake that the scheduled scan has been
stopped without sending the command to the firwmare, return
0 after having properly let cfg80211 know that the scan
has been cancelled.
This is basically the same as:
commit 9b520d8495
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Tue Nov 4 15:54:11 2014 +0200
iwlwifi: mvm: abort scan upon RFKILL
This code existed but not for all the different FW APIs
we support.
Fix this.
but for the scheduled scan case.
Link: http://permalink.gmane.org/gmane.linux.kernel.wireless.general/133232
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
EBS error detection isn't supported by all FWs, so turn it on
only if the FW advertises such support.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.
This fix is needed to fix few bugs regarding scans that take too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a flag that enables match found notification to align with
FW API change.
Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Make passive scan fragmentation depends on the number of active
interfaces. In case of single-MAC, make passive scan less fragmented.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This configuration defines the ratio between number of scan iterations
where EBS is involved to those where it is not.
This configuration was left unconfigured due to inaccurate documentation.
Fix documentation as well.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The antenna configuration has to be read also from OTP
Currently read only from FW image
Guideline: An antenna exists only if appears both in FW image & NVM
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove warning on scan complete with unknown ID, since this
scan could be already cleared in abort flow.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The ssid_bitmap should be unsigned, though it doesn't matter
much as the high bits aren't used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For background and scheduled scan, using the new unified scan API,
support random MAC address scanning.
Unfortunately, the firmware right now doesn't support randomising
itself, so for now do it on the host - we'll change this once the
firmware supports randomising the address for each scan iteration
using the address/mask.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
LMAC TLV bit may be on in FWs that support UMAC scan; so check
for UMAC TLV bit first.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This API uses second CPU scan commands, and can support multiple
simultaneous scans.
Adding the new API, and adding new mechanisms to deal with up to
8 simultaneous scans instead of the old scan status.
New scan API requires scan configuration for default scan parameters,
adding it in _up flow. Also updating scan configuration after updating
valid scan antennas via debugfs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since it's too complicated for the fw to insert a DS Parameter Set
element in the middle of the frame, it was decided that it should be
done by the host. The fw will only parse the frame and update the
current channel field.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The scan reference wasn't released in case of offloaded scan,
causing the refcount to go wrong and prevent the device
from going into d0i3.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Scan condition iterator assumes that an interface is associated if
phy_ctxt is assigned, but this isn't the sutuation in P2P device.
OTOH P2P device is never associated so we can simply ignore it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The net-detect feature will require a scan offload to be started in
the same way it is done now for scheduled scan. Spin a new function
off of the sched_scan_start op code for reuse. Additionally,
restructure the function a bit for more readability.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move iwl_mvm_max_scan_ie_len function to scan.c and fix the
implementation to conform with the LMAC scan API.
Since the correct implementation would leave us with unacceptably
tiny probes, add a workaround which returns a larger value.
In current implementation it's possible that unified_scan_lmac and
unified_sched_scan_lmac would return -ENOBUFS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set RRM_ENABLED (bit 6) flag in scan commands. When this flag is set
the fw will add WFA vendor-specific TPC report and DS parameter set
IEs into probe requests.
This bit is set for SCAN_OFFLOAD_REQUEST_CMD(0x51).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reduce basic active dwell time from 30 ms on 2.4 GHz and 20 on 5.2 to
20 on 2.4 and 10 on 5.2.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable fragmented scan that was diabled due to a FW bug.
New fixed FWs use a TLV bit to advertise fragmented scan support.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Initialize LMAC scan command.
Fix EBS flag to be dependant on TLV flg and fix other bugs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add new scan API that uses the same command 0x51 for both regular and
sched scan.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Split sched scan IEs to band specific and not band specific
blocks. Common IEs blocks may be sent to the FW once per command,
instead of per band.
This allows optimization of size of the command, which may be
required by some drivers (eg. iwlmvm with newer firmware version).
As this changes the mac80211 API, update all drivers to use the
new version correctly, even if they don't (yet) make use of the
split data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use num of scan channels as advertised by fw TLV.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The low-priority scan feature can be useful, e.g. for OBSS
scans (if those are required by the AP); add back support
for it, restoring the maximum out time to the value it was
for low-priority scan before that was removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use ksize to get scan command size instead of calculating it, to
avoid nasty bugs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current sched scan channel configuration code
configures all the supported channels for scanning.
However, this can result in SYSASSERT in some cases,
when the configured channel is disabled.
Instead, configure only the channels given in the
req struct, and set the channel_count field appropriately.
While on it, change the code to use channel->hw_value
instead of recalculating the channel number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
tail should be equal to the last valid index, so
decrease it by one.
This error causes in "a gap" in some cases (as well as
some possible out-of-bound write), finally resulting in
ucode assertion.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
CMD_SYNC is really 0 which is confusing:
if (cmd.flags & CMD_SYNC) is always false.
Fix this by simply removing its definition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add an option to notify mac80211 about sched scan complete from
iwl_mvm_stop_sched_scan(), to enable this notification when the
stop was called from within the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch enables Energy Based Scan (EBS) - intended to detect energy
on 5 GHz band channels. Passive scan on this band takes up to 2.64 sec
assuming 110mSec per-channel * 24 channels. EBS is designed to detect
energy on channels with intensive Wifi activity as well as those where
only beacons are transmitted. EBS completes sampling all channels within
shortest beacon frame transmission time. Total EBS duration is about 100
msec (typical beacon interval).
Detecting Wifi activity on 5 GHz band channels can significantly reduce
scan duration thus saving time and power. EBS failure reported by FW
disables EBS for current connection. It is re-enabled upon new
connection attempt on any WLAN interface.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware doesn't handle properly the fragmented scan.
Stop using it.
While at it change max_out_time and suspend_time units from
usec to TUs as expected by firmware API.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
While the scan_cmd should really be allocated in init (and
we do fail init in case the allocation failed), it doesn't
mean we should lock up the machine if something really bad
happened.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of system low latency configure passive scan to be fragmented.
Set the following scan parameters for both immediate and scheduled scan:
- passive scan fragment duration = 20ms
- out-of-channel time = 70ms
- suspend time = 105ms
Restructure channel's active/passive dwell time configuration to better
suit the above change.
The idea is that under low latency traffic passive scan is fragmented,
i.e. that dwell on a particular channel will be fragmented. Each
fragment dwell time is 20ms and fragments period is 105ms. Skipping to
next channel will be delayed by the same period (105ms). So suspend_time
parameter describing both fragments and channels skipping periods is set
to 105ms. This value is chosen so that overall passive scan duration
will not be too long. Max_out_time in this case is set to 70ms, so for
active scanning operating channel will be left for 70ms while for
passive still for 20ms (fragment dwell).
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some scan parameters should be dependent on traffic conditions.
Centralize conditions verification in one function and obtain
scan max out-of-channel and suspend time in that new function.
Rely on bound interfaces indication instead of association state
to calculate scan parameters. If no bound interfaces use default
values for out-of-channel and suspend time parameters.
Additionally, get rid of NL80211_SCAN_FLAG_LOW_PRIORITY checks
since no use case for this exists so far.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[reword commit log a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A scheduled scan is a more persistent setting and should take priority
over temporary regular scans. Abort the regular when a sched_scan
request arrives and then request the sched_scan.
The kernel API allows sending a sched_scan without canceling a regular
scan in progress, so this is our way to abstract the FW's limitations.
Make the scan-cancel Rx handler async and flush after invocation to
ensure new scans can't creep in before it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
cfg80211 assumes a scheduled scan is stopped synchronously. Wait for the
FW before returning to caller.
Don't do anything in the async handler in the stop-from-above flow.
There's no need to call the mac80211 sched-scan completion as the
cleanup will be automatic. Make sure the async handler is called before
the next incoming scan changes the scan_status by flushing the async
handlers after all invocations.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
BGN SKU won't scan on 5.2GHz obviously, but the firmware
still expects the driver to reserve space for the the probe
request for the 5.2GHz band.
Fix this by allocating space and leave it empty.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69541
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These inlines are pretty pointless now as they just return a
fixed struct value, remove them - the code even gets shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The scheduled scan matchsets were intended to be a list of filters,
with the found BSS having to pass at least one of them to be passed
to the host. When the RSSI attribute was added, however, this was
broken and currently wpa_supplicant adds that attribute in its own
matchset; however, it doesn't intend that to mean that anything
that passes the RSSI filter should be passed to the host, instead
it wants it to mean that everything needs to also have higher RSSI.
This is semantically problematic because we have a list of filters
like [ SSID1, SSID2, SSID3, RSSI ] with no real indication which
one should be OR'ed and which one AND'ed.
To fix this, move the RSSI filter attribute into each matchset. As
we need to stay backward compatible, treat a matchset with only the
RSSI attribute as a "default RSSI filter" for all other matchsets,
but only if there are other matchsets (an RSSI-only matchset by
itself is still desirable.)
To make driver implementation easier, keep a global min_rssi_thold
for the entire request as well. The only affected driver is ath6kl.
I found this when I looked into the code after Raja Mani submitted
a patch fixing the n_match_sets calculation to disregard the RSSI,
but that patch didn't address the semantic issue.
Reported-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some older versions of wpa_supplicant don't necessarily stop
scheduled scan before starting a regular scan, and there's
nothing in the API that requires it either. As a consequence
our driver's behaviour of not allowing scan while scheduled
scan was in progress broke userspace.
However, it is valid to unilaterally stop scheduled scan at
any point in time, so when a regular scan request comes just
abort the scheduled scan and run the regular scan.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take a reference when starting to scan and release it on completion.
Note that if the scan is cancelled/aborted, a completion will still be
sent up.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Notify scan completed if fw_restart flow isn't going to be run.
Otherwise, the scan will stay stack forever and mac80211 will
not be able to remove the interface.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Not doing so will let BT kill our probe requests leading to
failures in scan.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure scheduled scan to notify match found on every beacon
or probe response if the scan request doesn't contain valid ssid
list for filtering.
Without this configuration the FW passes all beacons to the host
but doesn't notify the stack that the scan results are ready for
processing.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware needs to be stopped quickly (100ms) after the
RFKILL interrupt fired. Failing to do so would allow the
firmware to access the radio registers which would lead to
a hardware error.
Before this change, we would kill the firmware only when
mac80211 stops the device which can take a fair amount of
time. Take a shortcut by stopping the device right away
in the interrupt.
This is not relevant if the current firmware is INIT
firmware since that firmware can run while in RFKILL.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Advertise driver's support for low priority scan.
Notice that this overwrites current setting by mac80211 which depends
only on hw scan support.
This scan priority can be configured by user space application
and it affects scan continuity, low priority scan
will be more fragmented scan.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Bit 0 in the scan offloading flags asks the filter
to pass all the results (instead of filtering them,
by default), rather than the other way around (like
it is defined and used today).
Fix the flag name appropriately, and fix its user.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fix is related to a scan request when associated (bgscan).
FW expects suspend time parameter in micro seconds while the driver
provides a value in time units. This bug leads to a high traffic
latency when scan is requested while traffic is in progress.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for scheduled scan according to firmware support.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New FW doesn't use the SSID from scan request template. Adding
a TLV flag to indicate the change, and fixing the flows to send
the first SSID in SSID list if the flag is on.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an option to set rx antennas for the scan command from debugfs.
Create a file called ant_rxchain in the mvm debugfs directory.
To choose antennas, write a number between 1-7 to ant_rxchain.
Write 1 for A, 2 for B, 3 for AB and so on.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When RFKill cuts short a scan, mac80211 cancels the scan.
This is done by sending a host command to the firmware, but
this command was dropped because of RFKill. Flag this
command as "SEND_IN_RFKILL" to make sure it is sent to the
firmware. The firmware will send SCAN_COMPLETE_NOTIFICATION
which will trigger a call to ieee80211_scan_completed.
If the scan cannot be aborted, it is because the firmware
already finished the scan but we hadn't notified mac80211
at the time mac80211 decided to cancel the scan. By the time
we see the scan could not be aborted, mac80211 has been
notified already.
This patch fixes situations in which we didn't notify
mac80211 upon completion of the scan that was cut short
by RFkill.
Cc: stable@vger.kernel.org [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable passive to active scan feature, on channels that was
active in the past hour.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set SSID bitmap for direct scan even on passive channels,
for the passive-to-active feature. Without this patch only
the SSID from probe request template is sent on passive
channels, after passive-to-active switching, causing us to
not find all desired networks.
Remove the unused passive scan mask constant.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bits 1-21 in this channel type attributes are indication for which
SSID is going to be sent on this channel. Since the first SSID is
sent implicitly in the probe request, we don't need to toggle its
bit here.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Increment index in each iteration. Without this increment we are
overriding the added SSIDs and we will send only the last SSId
and (n_ssids - 1) broadcast probes.
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the right source of information for the valid Tx
antennas, not the NVM.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
7000.c was released as GPL only by mistake: it should be
dual licensed - GPL / BSD.
The file that contains the license in the kernel is COPYING
and not LICENSE.GPL.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FW can differentiate between scans, according to the interface
type on which the scan was issues. Supply the interfaces type
information to the FW.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer firmware revisions have a completely new
firmware API. This is the new driver for this
new API.
I've listed the people who directly contributed
code, but many others from various teams have
contributed in other ways.
Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Amit Beka <amit.beka@intel.com>
Cc: Amnon Paz <amnonx.paz@intel.com>
Cc: Assaf Krauss <assaf.krauss@intel.com>
Cc: David Spinadel <david.spinadel@intel.com>
Cc: Dor Shaish <dor.shaish@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Eytan Lifshitz <eytan.lifshitz@intel.com>
Cc: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
