Occasionally, the device will send interrupts
while it is resuming, at a point where we are
not set up again to handle them. This causes
the core IRQ handling to completely disable
the IRQ, and then the driver won't work again
until it is reloaded/rebound.
To fix this issue disable the IRQ on suspend,
this will cause us to only get interrupts
again after we've setup everything on resume.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A pointer to the bus structure is still in iwl_priv. Finish
cleanup and remove it.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not needed since driver split.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some reason, WoWLAN doesn't always seem to
be happy with more advanced LQ commands. Since
we don't need them as we're not going to send
a lot of data, simply program the station with
the very simple default LQ command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
802.11 says:
"Sequence numbers for QoS (+)Null frames may be
set to any value."
However, if we use the normal counters then peers
will get confused with aggregation since there'll
be holes in the sequence number sequence.
To avoid that, don't assign sequence numbers to
QoS Null frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi GUy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updating the beacon every time right after one was
transmitted is pointless, most of the time we might
not even have to update it. We will update it every
time it changes, which includes from set_tim(), a
callback iwlwifi didn't implement so far.
This also reduces latency for clients, previously
we would update the beacon right after the previous
one was transmitted, and then a TIM change would
only take effect after that again -- updating the
beacon right after the TIM changes makes the TIM
change go out to the air faster.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For command queue testing, add "echo test" to debugfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
check the RF KILL flag in queue stuck watch dog function
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When detect command queue stuck, instead of reload the firmware
do the "echo" test to make sure it is really stuck before reload
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For error condition, STATUS_HCMD_ACTIVE already got clear before receive
tx cmd complete, give warning
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add "echo" host command for testing and drebugging to make sure uCode still
responding
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When detect cmd queue time out, display the current read/write pointer
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ftmac100 allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
If frame is under 64 bytes, page is freed, so increase truesize only for
bigger frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a 'truesize' argument to niu_rx_skb_append(), filled with rcr_size
by the caller to properly account frag sizes in skb->truesize
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ftgmac100 allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
If frame is under 64 bytes, page is freed, and truesize adjusted.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sky2 allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe allocates half a page per skb fragment. We must account
PAGE_SIZE/2 increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000 allocates half a page per skb fragment. We must account
PAGE_SIZE/2 increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000 allocates a full page per skb fragment. We must account PAGE_SIZE
increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2 allocates a full page per fragment. We must account PAGE_SIZE
increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix skb truesize underestimations of this driver.
Each frag truesize is exactly rx_frag_size bytes. (2048 bytes per
default)
A driver should not use "sizeof(struct sk_buff)" at all.
Signed-off-by: Eric Dumazet <eric.dumazet>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the driver version to 3.2.10.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds VMDq loopback pf support for i350 devices. The patch
is necessary since the register that enabled loopback was moved and
renamed from DTXSWC to TXSWC.
Signed-off-by: "Akeem G. Abodunrin" <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb_update/validate_nvm_checksum_with_offset() should be static.
Also removes unneeded prototypes for the above functions.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On i350 when traffic is looped back from a VF to the PF the value is byte
swapped from the normal format. In order to address this we need to add a
flag indicating that the ring will need to byte swap the loopback packets
prior to processing them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we mask interrupts in EIMS not in IMS there is no need to re-enable
mask bits in that register. As such we can remove the write to IMS from
the end of igb_msix_other.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change allows support for per packet timesync and global device reset
on the i350 adapter. These features were supported on both 82580 and i350
however it looks like several checks where not updated and as such the i350
support was not enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes certain that one interrupt is always initialized in
igb_request_irq. In addition we drop the use of adapter->pdev and
instead just call pdev since we made a local copy of the pointer earlier in
the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is mostly a drop of unnecessary pointer defines for q_vector when we
don't have issues with line width and don't have multiple references to
the pointer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct a check for change in FCoE priority when IEEE mode DCB is in use.
In IEEE mode a different function has to be used to get the FCoE priority
mask. Also, the check for the mask assumed that only one priority was set.
In case there should be more than one, check just the bit.
These changes help avoid link flapping issues that can come up when IEEE
DCB is in use.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add 2 new counters to ethtool:
1. Count DDP allocation failure since we max the number of buffers
allowed in one DDP context.
2. Count DDP allocation failure since we max the number of buffers
allowed in one DDP context when we alloc an extra buffer.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible for a VF to set an invalid target DMA address in its
Tx/Rx descriptor buffer pointers. The workarounds in this patch
will guard against such an event and issue a VFLR to the VF in response.
The VFLR will shut down the VF until an administrator can take action
to investigate the event and correct the problem.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prevents lots of broken frames from showing up on monitor interfaces
by default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: Fix incorrect key_miss handling" changed the code
to only report key miss errors if a MIC error wasn't reported.
When checking the flags in that order in the MAC code, it might miss some
real events, because the value of the MIC error flag is undefined under
some conditions.
The primary issue addressed by the previous commit is making sure that
MIC errors are properly reported on the STA side. This can be fixed in
a better way by adding a separate rx status flag for key miss and
ignoring it for multicast frames.
This fix slightly improves stability in AP mode on some older hardware,
like AR9132.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is unused since the previous dead code that was using it had been
removed earlier.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code for handling various restrictions concerning regulatory limits,
antenna gain, etc. is very convoluted and duplicated across various
EEPROM parsing implementations, making it hard to review.
This patch partially cleans up the mess by unifying regulatory limit
handling in one function and simplifying handling of antenna gain.
It also removes unused transmit power scaling arrays from the EEPROM code,
which belonged to an unimplemented API that isn't supposed to be in
the driver anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY errors relevant for ANI are always tracked by hardware counters, the
bits that allow them to pass through the rx filter are independent of that.
Enabling PHY errors in the rx filter often creates lots of useless DMA traffic
and might be responsible for some of the rx dma stop failure warnings.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't want to report random quality info (new PHYs are affected).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current debug parameter is applied to rtlwifi, which means that all
loaded drivers have the same level of debugging applied. In addition,
the previous method requires a two-step load process to enable debugging.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When tx is suspended temporarily and the queue is flushed, do not increase
the retry count or attempt to send out BAR frames. Instead simply retry
the affected subframes normally after the reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not increment the retry counter if packets to a sleeping station
were not sent because of tx failure, instead of only checking the filter
flag.
Clear the PS filter only after an A-MPDU was reported as filtered,
otherwise the hardware might do some unnecessary extra retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export how many times each of the reset triggers has fired through debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If "axq_qnum >= ARRAY_SIZE(sc->tx.txq)", then the call to
ath9k_hw_releasetxqueue() would read beyond the end of the ah->txq[]
array and possibly corrupt memory. Fortunately,
ath9k_hw_setuptxqueue() doesn't return high values of "axq_qnum" and
this code can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
th5k_hw_setup_tx_queue() returns a valid offset into the ah->ah_txq[]
array. The ah->ah_txq[] and the ah->txqs[] array are the same size.
Both have AR5K_NUM_TX_QUEUES elements. So this error handling code
will never trigger.
Also it's wrong. The call to ath5k_hw_release_tx_queue() with a qnum
of AR5K_NUM_TX_QUEUES or more will just trigger a WARN_ON() and
return. Or if it missed the WARN_ON(), it would just corrupt some
memory and return.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch for init calib cfg disable a set of calibration for both
init and runtime which cause performance issue, Fix it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the brcm80211 tree to drivers/net/wireless, and disable the version that's
in drivers/staging. This version includes the sources currently in staging,
plus any changes that have been sent out for review.
Sources in staging will be deleted in a followup patch.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/ath/ath6kl/cfg80211.o
drivers/net/wireless/ath/ath6kl/cfg80211.c:1838:2: warning: initialization from incompatible pointer type
Caused by commit e9f935e3e8dc0bddd0df6d148165d95925422502...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes file references to moved or deleted files
outside of Documentation/.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the 16 bit access to mscan registers there's too much data copied to
the zero initialized CAN frame when having an odd number of bytes to copy.
This patch ensures that only the requested bytes are copied by using an
8 bit access for the remaining byte.
Reported-by: Andre Naujoks <nautsch@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some consolidations of NPAR configuration
when FCoE and iSCSI L2 clients will get the same id,
in this case FCoE ring will be non-functional.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The doorbell register was being unconditionally swapped. In x86, that
meant it was being swapped to BE and written to the descriptor and to
memory, depending on the case of blue frame support or writing to
doorbell register. On PPC, this meant it was being swapped to LE and
then swapped back to BE while writing to the register. But in the blue
frame case, it was being written as LE to the descriptor.
The fix is not to swap doorbell unconditionally, write it to the
register as BE and convert it to BE when writing it to the descriptor.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Reported-by: Richard Hendrickson <richhend@us.ibm.com>
Cc: Eli Cohen <eli@dev.mellanox.co.il>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe reported to me that right after a bring up of a r6040 interface
the ethtool output had no consistent output with respect to link duplex
and speed. Fix this by adding a missing phy_start call in r6040_up and
conversely a phy_stop call in r6040_down to properly initialize phy states.
Reported-by: Joe Chou <Joe.Chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query port will now identify a 40G Ethernet speed.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdevice was being freed without being unregistered first if
mlx4_SET_PORT_general or mlx4_INIT_PORT failed.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of bits taken from mac table index in QP
calculation should be based on log_num_mac parameter.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a memory leak caused by missing iounmap when device
is being released.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Sharon Cohen <sharonc@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moderation is now done per ring and coalescing is enabled
by set_ring_param in ethtool.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug where ring size change caused insufficient memory
upon driver restart due to unreleased EQs.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now only RX rings used irq per ring
and TX used only one per port.
>From now on, both of them will use the
irq per ring while RX & TX ring[i] will
use the same irq.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Sharon Cohen <sharonc@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Rx hashing.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves the Tx hang check into the ring flags.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up several issues with VLANs on igb after the recent
changes that were meant to leave the VLANs enabled/disable via the
netdev->features flags.
Specifically the Rx VLAN settings were being dropped after reset due to the
fact that they were not being restored correctly. In addition I removed
the IRQ disable/enable since those were in place to protect the setting of
vlgrp.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of doing a byte swap on the staterr bits in the Rx descriptor we can
save ourselves a bit of space and some CPU time by instead just testing for
the various bits out of the Rx descriptor directly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the netdev now has its' own checksum flag to indicate if Rx checksum
is enabled we might as well use that instead of using the ring flag.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to cleanup some of the IVAR register configuration.
igb_assign_vector had become pretty large with multiple copies of the same
general code for setting the IVAR. This change consolidates most of that
code by adding the igb_write_ivar function which allows us just to compute
the index and offset and then use that information to setup the IVAR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves information related to interrupt throttle rate
configuration into a separate q_vector sub-structure called a work
container. A similar change has already been made for ixgbe and this work
is based off of that.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves all of the ring flags into a single value. The advantage
to this is that there is one central area for all of these flags and they
can all make use of the set/test bit operations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a number of places where we have values that are stored as u16
but are being converted to int unnecessarily. In order to avoid that we
should convert all variables that deal with the next_to_clean, next_to_use,
and count to u16 values.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to update the ring and vector allocations so that they
are per node instead of allocating everything on the node that
ifconfig/modprobe is called on. By doing this we can cut down
significantly on cross node traffic.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of storing most of the data for the TX hot path in the stack until
we are ready to write the descriptor we can save ourselves some time and
effort by pushing the SKB, tx_flags, gso_size, bytecount, and protocol into
the first igb_tx_buffer since that is where we will end up putting it
anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pm-runtime:
PM / Tracing: build rpm-traces.c only if CONFIG_PM_RUNTIME is set
PM / Runtime: Replace dev_dbg() with trace_rpm_*()
PM / Runtime: Introduce trace points for tracing rpm_* functions
PM / Runtime: Don't run callbacks under lock for power.irq_safe set
USB: Add wakeup info to debugging messages
PM / Runtime: pm_runtime_idle() can be called in atomic context
PM / Runtime: Add macro to test for runtime PM events
PM / Runtime: Add might_sleep() to runtime PM functions
Add support for reporting ring sizes via ethtool -g to the 8139cp driver.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change will combine the writes of tx_buffer_info and the Tx data
descriptors into a single function. The advantage of this is that we can
avoid needless memory reads from the buffer info struct and speed things up
by keeping the accesses to the local registers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to combine all of the TX flags fields into one u32
flags field so that it can be stored into the tx_buffer_info structure.
This includes the time stamp flag as well as mapped_as_page flag info.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to cleanup the protocol handling in the transmit path
so that it correctly offloads software VLAN tagged frames.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve the readability of the driver by separating
out the cmd_type configuration and the olinfo configuration into their own
functions. By doing this it is much easier to determine which ingredients
go into setting up these to portions of the descriptor.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change converts two tx_buffer_info index values into pointers. The
advantage to this is that we reduce unnecessary computations and in the case
of next_to_watch we get an added bonus of the value being able to provide
additional information as a NULL value indicates it is unset versus a 0 not
having any meaning for the index value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to simplify the transmit path by reducing the overhead
for creating a transmit context descriptor. The current implementation is
split with igb_tso and igb_tx_csum doing two separate implementations on
how to setup the tx_buffer_info structure and the tx_desc. By combining
them it is possible to reduce code and simplify things since now only one
function will create context descriptors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to be able to improve the performance of the TX path it has been
necessary to add addition info to the tx_buffer_info structure. However a
side effect is that the structure has gotten larger and this in turn has
also increased the size of the RX buffer info structure. In order to avoid
this in the future I am splitting the single buffer_info structure into two
separate ones and instead I will join them by making the buffer_info
pointer in the ring a union of the two.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is to make the NAPI budget limits for transmit
adjustable. Currently they are only set to 128, and when
the changes/improvements to NAPI occur to allow for adjustability,
it would be possible to tune the value for optimal
performance with applications such as routing.
v2: remove tie between NAPI and interrupt moderation
fix work limit define name (s/IXGBE/IGB/)
Update patch description to better reflect patch
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
When short packets are received with jumbos enabled on 82579, they can be
interpreted to have a receive address that does not match any configured
address. This is due to a hardware bug that can be worked around by
reducing the number of IPG octets added when the packet is transferred from
the PHY to the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000 driver when running with lockdep could run into
some possible deadlocks between the work items acquiring
rtnl and the rtnl lock being acquired before work items
were cancelled.
Use a private mutex to make sure lock ordering isn't violated.
The private mutex is only used to protect areas not generally
covered by the rtnl lock already.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the previous commit, there are several functions
that are only ever called from thread context, and are
able to sleep with msleep instead of mdelay.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Thomas Gleixner (tglx) reported that e1000 was delaying for many milliseconds
(using mdelay) from inside timer/interrupt context. None of these paths are
performance critical and can be moved into threads/work items. This patch
implements the work items and the next patch changes the mdelays to msleeps.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump the version string to better match pair up with the out of tree
driver that contains the same functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current wl12xx fw (7.3.0.0.77) supports both STA and AP mode, and
we no longer use AP-mode-specific quirks.
WL12XX_QUIRK_END_OF_TRANSACTION is still used for certain HWs, while
WL12XX_QUIRK_LPD_MODE is not used anymore.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx FW supports HW channel switch. If we don't use it,
sometimes the firmware gets confused when recalibrating to the new
channel, causing RX problems. This commit adds HW channel switch
support by implementing the channell_switch op.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
[added one comment, remove the tx_flush and rephrased the commit message]
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wiphy max_sched_scan_ie_len attribute was not set correctly and
remained as 0, so when IEs were being passed in a scheduled scan, we
were returning -EINVAL.
Fix this by setting the attribute properly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
p2p packets should go out only with OFDM rates.
Configure a new rate policy that will (later) be used
during p2p_find (when the p2p_cli / p2p_go interfaces
are in use, we won't have to use this policy, as
the configured rates should already be OFDM-only).
Additionally, update CONF_TX_MAX_RATE_CLASSES to reflect
the current value from the fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch verifies that the length of a buffer stored in a linked list
of pages is small enough to fit into a skb.
If the size is larger than a max size of a skb, it means that we shouldn't
go ahead building skbs anyway since we won't be able to send the buffer as
the user requested.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Cc: kvm@vger.kernel.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only function 1 has support for Alternate MAC Address in the EEPROM before,
this update now allow function 2 and 3 to have support for Alternate MAC
Address in the EEPROM.
Signed-off-by: "Akeem G. Abodunrin" <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code check word 0x37 in the EEPROM, if it is 0xFFFF _or_ 0x0000, then
there is no Alternate MAC Address in the EEPROM.
Signed-off-by: "Akeem G. Abodunrin" <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes "overwrite" problem. without this fix, SFP I2C EEPROM
data, which is located at A0 can be overwritten by the phy write function.
Signed-off-by: "Akeem G. Abodunrin" <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Receiving PFC (priority flow control) frames while the feature
is off should not pause the traffic class. On the X540 devices
the traffic class react to frames if it was previously enabled
because the field is incorrectly cleared.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X540 devices can only support up to 4 traffic classes and
guarantee a "lossless" traffic class on some platforms.
This patch sets the X540 devices to initialize a max
traffic class value of 4 at probe time.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch correctly configures DCB when less than 8 traffic classes
are available in hardware.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix PFC mask generation to OR in only a single bit for each priority in
the PFC mask returned via netlink.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PCI device ID 0x1501 has a hardware bug when the link downshifts for
whatever reason which requires a workaround. The workaround already exists
for other similar devices but is not called for 0x1501 (it should be called
for any ICH8-based device that uses a GbE PHY). There is also one other
instance when the workaround should be called - after disabling gigabit
speed when going to Sx.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During suspend, the PHY must be reset for workaround updates to take effect
without restarting auto-negotiation. Also, set the disable GbE and enable
Low Power Link Up (LPLU) if the EEPROM is configured to do likewise in
either D0 or non-D0a instead of just the latter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code is after the break statement so it never gets used. The
"vlan_mac_obj" variable does get initialized properly, so we can just
delete this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: Dimitris Michailidis <dm@chelsio.com>
Cc: Casey Leedom <leedom@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jon Mason <mason@myri.com>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
netback currently uses frag->page to store a temporary index reference while
processing incoming requests. Since frag->page is to become opaque switch
instead to using page_offset. Add a wrapper to tidy this up and propagate the
fact that the indexes are only u16 through the code (this was already true in
practice but unsigned long and in were inconsistently used as variable and
parameter types)
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Use DMA_TO_DEVICE and dma_mapping_error() -DaveM ]
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
82598 and 82599 do not ship with this type of PHY
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a problem in the ixgbe driver with the reporting of the flow
control parameters. The autoneg parameter is shown to be of if
*either* it really is off, or current modes for both tx and rx are off.
The problem is seen when the parameters are read or set when the link
is down. In this case, the driver sees that tx and rx are currently off
and therefore autoneg parameter is incorrectly reported to be off too.
Also, the ethtool binary can not set the autoneg off since it sees that
it already is. When a link later comes up, the autonegotiation is
carried out normally and the driver later on reports the autoneg
parameter to be on (as it is) and then it can also be changed with
ethtool.
The patch is made against v3.0 kernel, but the problem seems to be there
since v2.6.30-rc1.
Reviewer comments: What we are trying to do is to disable flow control
while the cable is disconnected. Since ixgbe defaults to full flow
control, we call ethtool -A autoneg off rx off tx off while the cable
is disconnected. This doesn't work, because the driver sets
hw->fc.current_mode = ixgbe_fc_none if the cable is unplugged.
ixgbe_get_pauseparam() then reports to ethtool that nothing needs to be
done. The code fixes this, but it might have some unknown consequences.
Signed-off-by: Mika Lansirinne <mika.lansirinne@stonesoft.com>
Reviewed-by: Esa-Pekka Pyokkimies <esa-pekka.pyokkimies@stonesoft.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disabling flow control in ixgbe_check_mac_link() results in incorrect
reporting by ethtool when link goes down, so remove it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
MFLCN register is used to set Rx flow control on parts newer than 82598.
This patch sends the value of MFLCN to ethtool, so it can be used in a
register dump (ethtool -d).
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for new device ID.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue with storing the driver version for the
firmware. If the os does not support the particular firmware
management tools, the firmware requires a driver version to be written
as 0xFFFFFFFF rather than the actual driver version.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since ixgbe_raise_i2c_clk() can never return anything else than 0
this patch removes it's return value and all checks for it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the data field in ixgbe_read_i2c_byte_generic so it does not
accumulate 1 bit using the same variable multiple times.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It some situations the driver sets __IXGBE_RESETTING and then
__IXGBE_DOWN flags. It is possible a link check may sneak in
between.
This patch adds check for both flags.
The idea is to reduce register reads while the PHY is resetting.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The initial function and setup tables can be marked as constant.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Packets should always be forwarded to the lowerdev using dev_forward_skb.
vlan->forward is for packets being forwarded directly to another macvlan/
macvtap device (used for multicast in bridge mode).
Reported-and-tested-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/built-in.o: In function `bfa_ioc_ct2_poweron':
(.text+0xcdc90): multiple definition of `bfa_ioc_ct2_poweron'
drivers/scsi/built-in.o:(.text+0x17f9a0): first defined here
This patch renames bfa_ioc_ct2_poweron() to bfa_nw_ioc_ct2_poweron() to avoid
multiple definition with Brocade scsi driver. It also modifies asic specific
interface setup to allocate MSIX resources at power on in case of 1860 HW with
no asic block and warns if the asic gen is neither BFI_ASIC_GEN_CT nor
BFI_ASIC_GEN_CT2.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check patch was complaining...mostly replaced:
if ((ret = asix_foo(xx)) < 0) ...
with
ret = asix_foo(xx);
if (ret < 0) ...
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Asix provided this patch and I've confirmed "Plugable USB2-E1000" and
"Shenzhen Winstars NWU220G" USB dongles can get a link and TX/RX data.
Signed-off-by: "Freddy Xin" <freddy@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix phy initialization for AX88772 (USB 2.0 100BT). Failure was
occasionally DHCP wouldn't work after reboot or suspend/resume cycle.
Remove MONITOR_MODE. In this mode, Received packets are not buffered when
the remote wakeup is enabled.
Signed-off-by: "Freddy Xin" <freddy@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Acked-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
the AR_SREV register does not seems to indicate whether AR9480 is
pci_express capable or not though the other information like macVersion
etc can be obtained properly. this fix is essential as ASPM won't be intialized
and its related driver functionality ath9k_hw_configpcipowersave won't be
called
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch fixes the assumption of maximum number of GPIO pins present
in AR9287/AR9300. this fix is essential as we might encounter some
functionality issues involved in accessing the status of GPIO pins which
are all incorrectly assumed to be not within the range of max_num_gpio
of AR9300/AR9287 chipsets
Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent patches added support for resetting the SD8686 hardware when
commands time out, which seems to happen quite frequently soon after
resuming the system from a Wake-on-WLAN-triggered resume.
At http://dev.laptop.org/ticket/10969 we see the same thing happen
with transmits. In this case, the hardware will fail to respond to
a frame passed for transmission, and libertas (correctly) will block
all further commands and transmissions as the hardware can only
deal with one thing at a time. This results in a lockup while the
system waits indefinitely for the dead card to respond.
Hook up a TX lockup timer to detect this and reset the hardware.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.
The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
ops.conf_tx = conf_tx_op;
@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
conf_tx_op (
- struct ieee80211_hw *hw,
+ struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u16 queue,
const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename the iwlagn module as iwlwifi in preparation for future
changes. Add an alias to iwlagn for backward compatibility.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this extends the bits for rf kill GPIO selection to [7:2] from [4:2] as
we use GPIO pin 11 as rfkill for AR9480 and also remove few unused
macros
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: "Hu, Russell" <rhu@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In failure case locks are not allocated in mwifiex_register().
So mwifiex_free_lock_list() routine call becomes redundant.
Also we don't need to check return type for mwifiex_init_lock_list()
routine. It never fails.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "mwifiex: remove list traversal.."(fcf2176c87..)
wrongly modifies AMSDU aggregation check. Due to this even though
packet size for iperf traffic is already large, we unnecessarily
try to aggregate them which adds some delay. If Tx iperf is started
on UUT for 30 seconds, UUT keeps sending Tx packets for few more
seconds.
That commit is reverted to fix the problem.
Also, MIN_NUM_AMSDU check is moved inside the loop to optimize the
loop.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was reported and tested by Martin Walter over at AVM GmbH Berlin.
This also applies to 3.0.1 so sendint to stable.
Cc: s.kirste@avm.de
Cc: d.friedel@avm.de
Cc: Martin Walter <m.walter@avm.de>
Cc: Peter Grabienski <pgrabien@qca.qualcomm.com>
Cc: stable@kernel.org
Tested-by: Martin Walter <m.walter@avm.de>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pch_gbe driver has an issue which a network stops,
when receiving traffic is high.
In the case, The link down and up are necessary to return a network.
This patch fixed this issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link was downed during network use,
there is an issue on which PC freezes.
This patch fixed this issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a VM is saved and restored (or migrated) the netback driver will no
longer process any Tx packets from the frontend. xenvif_up() does not
schedule the processing of any pending Tx requests from the front end
because the carrier is off. Without this initial kick the frontend
just adds Tx requests to the ring without raising an event (until the
ring is full).
This was caused by 47103041e9 (net:
xen-netback: convert to hw_features) which reordered the calls to
xenvif_up() and netif_carrier_on() in xenvif_connect().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware is cached during the first successful call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().
It's similar to 953a12cc28 but the
firmware is mandatory.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit removed some including headers:
"net: sh_eth: move the asm/sh_eth.h to include/linux/"
(commit id: d4fa0e35fd)
Then, the build failure happened on the linux-next:
drivers/net/ethernet/renesas/sh_eth.c:601: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/net/ethernet/renesas/sh_eth.c:1970: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: function declaration isn't a prototype
drivers/net/ethernet/renesas/sh_eth.c:1971: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: function declaration isn't a prototype
drivers/net/ethernet/renesas/sh_eth.c:1972: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: function declaration isn't a prototype
This patch fixes the issue. This patch also get back include/kernel.h
and linux/spinlock.h.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a test where a pair of bonding interfaces using ARP monitoring
were both brought up and torn down (with an rmmod) repeatedly, a panic
in the timer code was noticed. I tracked this down and determined that
any of the bonding functions that ran as workqueue handlers and requeued
more work might not properly exit when the module was removed.
There was a flag protected by the bond lock called kill_timers that is
set when the interface goes down or the module is removed, but many of
the functions that monitor link status now unlock the bond lock to take
rtnl first. There is a chance that another CPU running the rmmod could
get the lock and set kill_timers after the first check has passed.
This patch does not allow any function to queue work that will make
itself run unless kill_timers is not set. I also noticed while doing
this work that bond_resend_igmp_join_requests did not have a check for
kill_timers, so I added the needed call there as well.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Liang Zheng <lzheng@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also changing it's frequency to once every 64s instead of existing 32s as
it was shown to affect performance
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was manifesting as a crash when FAT Dump extraction was attempted on a PPC machine.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was showing up as junk value on PPC /Big endian machines since
it was marked as a byte.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 60s delay before timeout on polling Bit 31 so that FAT dump can
complete when reset occurs.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes compilation errors when compiling for ARM:
ath6kl/debug.c:312: error: implicit declaration of function 'vmalloc'
ath6kl/debug.c:312: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:342: error: implicit declaration of function 'vfree'
ath6kl/debug.c:696: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:871: warning: assignment makes pointer from integer without a cast
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
My earlier debug log additions added these warnings when compiling 64 bit
kernels:
ath6kl/init.c:962: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:975: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:988: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:1009: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:1192: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
ath6kl/init.c:1236: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
ath6kl/init.c:1267: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
Reported-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Usually you have to take the bus lock. Why not here too?
I saw this when working on something else. Not even compile tested.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Cc: "Uwe Kleine-Konig" <u.kleine-koenig@pengutronix.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses to the mdio busses must be done with the mdio_lock to ensure
proper operation. Conveniently we have the helper function
mdiobus_read() to do that for us. Lets use it in get_phy_id() instead
of accessing the bus without the lock held.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add uAPSD support to mac80211. This is probably not
possible with all devices, so advertising it with
the cfg80211 flag will be left up to drivers that
want it.
Due to my previous patches it is now a fairly
straight-forward extension. Drivers need to have
accurate TX status reporting for the EOSP frame.
For drivers that buffer themselves, the provided
APIs allow releasing the right number of frames,
but then drivers need to set EOSP and more-data
themselves. This is documented in more detail in
the new code itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For uAPSD implementation, it is necessary to know on
which ACs frames are buffered. mac80211 obviously
knows about the frames it has buffered itself, but
with aggregation many drivers buffer frames. Thus,
mac80211 needs to be informed about this.
For now, since we don't have APSD in any form, this
will unconditionally set the TIM bit for the station
but later with uAPSD only some ACs might cause the
TIM bit to be set.
ath9k is the only driver using this API and I only
modify it in the most basic way, it won't be able
to implement uAPSD with this yet. But it can't do
that anyway since there's no way to selectively
release frames to the peer yet.
Since drivers will buffer frames per TID, let them
inform mac80211 on a per TID basis, mac80211 will
then sort out the AC mapping itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
both sta and lq_sta are guaranteed to be not null in the
calling function so we don't need to check them here.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_gpio_get reads the GPIO in/out registers to get the status of
GPIO pins, so use PS wrappers
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Making adding and deleting virtual interfaces dynamic. Adding
handlers for creating and deleting virtual interface with
given name and dev respectively.
Also, creating default interface of type station on insmod of
the driver.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iw dev mlan0 link" shows wrong data rate, because data rate is
not sent properly to cfg80211 stack. Also stack is not updated
with mcs and Tx data flags information.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In disconnected state "iw dev mlan0 link" command will return
from cfg80211 stack itself. We also have an error check in
mwifiex_cfg80211_get_station() routine. Therefore the code
under "if (!priv->media_connected)" condition in
mwifiex_rate_ioctl_get_rate_value() routine becomes unreachable.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An extra call to mwifiex_dump_station_info() routine in get_station
callback function is redundant
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of the rx status's is_mybeacon in order to avoid
redundant memcmp.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fill the ampdu_[ack]_len for both aggregation and normal frames.
So that we could avoid unnecesary conditional at tx status.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Add a callback in the BNA, which is called before sending FW command to stop
RxQs. After this callback is called, driver should not post anymore Rx
buffers to the RxQ. This addresses a small window where driver posts Rx
buffers while FW is stopping/has stopped the RxQ.
- Registering callback function, rx_stall_cbfn, during bna_rx_create.
Invoking callback function, rx_stall_cbfn, before sending rx_cfg_clr
command to FW
- Bnad_cb_rx_stall implementation - set a flag in the Rxq to mark buffer
posting disabled state. While posting buffers check for the above flag.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Fix to release soft reset in PLL init for HW
- Added stats attributes and new bfi msg class
- Removed some unused code and typo fixes
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables new HW Brocade 1860. Add BFA_CM_NIC capability mask to
bfa_ioc_attr, Sub-System Device ID Info and support for Brocade 1860 device
ID to bfa_ioc.c and bnad.c.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device ID 0x22 and new asic generation BFI_ASIC_GEN_CT2 for 1860.
Implement FW download from user space for new Brocade HW.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add capability map and generic model name scheme for manufacturing block.
Add card types for new HW.
Remove bfa_mfg_is_card_type_valid and ibfa_mfg_adapter_prop_init_flash_ct
macros.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic to set ASIC specfic interface in IOC, HW interface initialization
APIs, mode based initialization and MSI-X resource allocation for 1860 with
no asic block. Add new h/w specific register definitions and setup registers
used by IOC logic.
Use normal kernel declaration style, c99 initializers and const for mailbox
structures. Remove unneeded parentheses.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make USB-to-Ethernet-adapters (depending on usbnet) support
timestamping, the "skb_defer_rx_timestamp" and "skb_tx_timestamp" function
calls are added.
Signed-off-by: Michael Riesch <michael@riesch.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use hardcoded irq num and replace it with
FEC_IRQ_NUM macro.
Signed-off-by: Xiao Jiang <jgq516@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed that the legacy Interrupt handler didn't have the same
ECC warning as did the MSI. So this patch adds it.
Signed-off-by: Don Skidmore <donald.c.skidmore>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 thermal sensor interrupt isn't a General Purpose Interrupt
so doesn't need to be enabled in ixgbe_setup_gpie(). Likewise X540 doesn't
use the SDP0 for thermal sensor so it doesn't need to be enabled for any
device other than 82599.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to enable thermal sensors for the x540 hardware, as well as a
thermal interrupt check which will exit with a critical message of a
thermal overheat is detected. Intent of code allows other mac types to
be added with different configuration in the future.
Fixed in this version is the addition of setting the temp_sensor
capable flag which was previously only set for a specific mac.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Revise high and low threshold marks wrt flow control to account
for the X540 devices and latency introduced by the loopback
switch.
Without this it was in theory possible to drop frames on a
supposedly lossless link with X540 or SR-IOV enabled.
Previously we used a magic number in a define to calculate the
threshold values. This made it difficult to sort out exactly
which latencies were or were not being accounted for. Here
I was overly explicit and tried to used #define names that would
be recognizable after reading the IEEE 802.1Qbb specification.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable LLI for FCoE since regular interrupt
and their moderation rate works slightly better
for FCoE also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to help cleanup the interrupt throttle rate logic by
storing the interrupt throttle rate as a value in microseconds instead of
interrupts per second. The advantage to this approach is that the value
can now be stored in an 16 bit field and doesn't require as much math to
flip the value back and forth since the hardware already used microseconds
when setting the rate.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes to clean up the vlan rx path broke trunk vlan. Trunk vlans in
a VF driver are those set using:
"ip link set <pfdev> vf <n> <vlanid>"
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Doing an 'ifconfig ethN down' followed by an 'ifconfig ethN up' on a qemu-kvm
guest system configured with two e1000 NICs can result in an 'unable to handle
kernel paging request at 0000000100000000' or 'bad page map in process ...' or
something similar.
These result from a 4096-byte page being corrupted with the following two-word
pattern (16-bytes) repeated throughout the entire page:
0x0000000000000000
0x0000000100000000
There can be other bits set as well. What is a constant is that the 2nd word
has the 32nd bit set. So one could see:
:
0x0000000000000000
0x0000000100000000
0x0000000000000000
0x0000000172adc067 <<< bad pte
0x800000006ec60067
0x0000000700000040
0x0000000000000000
0x0000000100000000
:
Which came from from a process' page table I dumped out when the marked line
was seen as bad by print_bad_pte().
The repeating pattern represents the e1000's two-word receive descriptor:
struct e1000_rx_desc {
__le64 buffer_addr; /* Address of the descriptor's data buffer */
__le16 length; /* Length of data DMAed into data buffer */
__le16 csum; /* Packet checksum */
u8 status; /* Descriptor status */
u8 errors; /* Descriptor Errors */
__le16 special;
};
And the 32nd bit of the 2nd word maps to the 'u8 status' member, and
corresponds to E1000_RXD_STAT_DD which indicates the descriptor is done.
The corruption appears to result from the following...
. An 'ifconfig ethN down' gets us into e1000_close(), which through a number
of subfunctions results in:
1. E1000_RCTL_EN being cleared in RCTL register. [e1000_down()]
2. dma_free_coherent() being called. [e1000_free_rx_resources()]
. An 'ifconfig ethN up' gets us into e1000_open(), which through a number of
subfunctions results in:
1. dma_alloc_coherent() being called. [e1000_setup_rx_resources()]
2. E1000_RCTL_EN being set in RCTL register. [e1000_setup_rctl()]
3. E1000_RCTL_EN being cleared in RCTL register. [e1000_configure_rx()]
4. RDLEN, RDBAH and RDBAL registers being set to reflect the dma page
allocated in step 1. [e1000_configure_rx()]
5. E1000_RCTL_EN being set in RCTL register. [e1000_configure_rx()]
During the 'ifconfig ethN up' there is a window opened, starting in step 2
where the receives are enabled up until they are disabled in step 3, in which
the address of the receive descriptor dma page known by the NIC is still the
previous one which was freed during the 'ifconfig ethN down'. If this memory
has been reallocated for some other use and the NIC feels so inclined, it will
write to that former dma page with predictably unpleasant results.
I realize that in the guest, we're dealing with an e1000 NIC that is software
emulated by qemu-kvm. The problem doesn't appear to occur on bare-metal. Andy
suspects that this is because in the emulator link-up is essentially instant
and traffic can start flowing immediately. Whereas on bare-metal, link-up
usually seems to take at least a few milliseconds. And this might be enough
to prevent traffic from flowing into the device inside the window where
E1000_RCTL_EN is set.
So perhaps a modification needs to be made to the qemu-kvm e1000 NIC emulator
to delay the link-up. But in defense of the emulator, it seems like a bad idea
to enable dma operations before the address of the memory to be involved has
been made known.
The following patch no longer enables receives in e1000_setup_rctl() but leaves
them however they were. It only enables receives in e1000_configure_rx(), and
only after the dma address has been made known to the hardware.
There are two places where e1000_setup_rctl() gets called. The one in
e1000_configure() is followed immediately by a call to e1000_configure_rx(), so
there's really no change functionally (except for the removal of the problem
window. The other is in __e1000_shutdown() and is not followed by a call to
e1000_configure_rx(), so there is a change functionally. But consider...
. An 'ifconfig ethN down' (just as described above).
. A 'suspend' of the system, which (I'm assuming) will find its way into
e1000_suspend() which calls __e1000_shutdown() resulting in:
1. E1000_RCTL_EN being set in RCTL register. [e1000_setup_rctl()]
And again we've re-opened the problem window for some unknown amount of time.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If request_irq fails, the ibmveth driver will overwrite
the rc and end up returning a successful rc on its open
function, resulting in an oops later when a packet gets
sent and buffers are not allocated due to the failed open.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix EEH recovery on new P Series platform by
requesting fundamental reset.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has two warning messages that might be triggered
by normal use cases. When they appear, the messages give the
impression of a never ending series of errors.
This commit changes them to debug messages instead.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for SJW user settings to not set the synchronization
jump width (SJW) to 1 in any case when using the in-kernel bittiming
calculation.
The ip-tool from iproute2 already supports to pass the user defined SJW
value. The given SJW value is sanitized with the controller specific sjw_max
and the calculated tseg2 value. As the SJW can have values up to 4 providing
this value will lead to the maximum possible SJW automatically. A higher SJW
allows higher controller oscillator tolerances.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch also changes writel/readl to iowrite32/ioread32.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver for the SJA1000 based PCMCIA card 'CPC-Card' from
EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Markus Plessing <plessing@ems-wuensche.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otheriwse the module.h split up fails like this:
drivers/net/wireless/ath/ath6kl/init.c:27:26: error: expected ')' before 'uint'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For some reason firmware is sending invalid rates when we try to
query current bitrate from ath6kl_get_station() and a warning is issued:
[ 3810.415720] ath6kl: invalid rate: 1935633515
[ 3811.105493] ath6kl: invalid rate: 1935633515
[ 3811.556063] ath6kl: invalid rate: 1935633515
As the warning happens way too often, convert the warning to a debug
message once we have a proper fix. But to make it easy to follow
how often the problem appears, add a debugfs to print
various statistics about workarounds and make this issue the first WAR.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* git://github.com/davem330/net:
ipv6-multicast: Fix memory leak in IPv6 multicast.
ipv6: check return value for dst_alloc
net: check return value for dst_alloc
ipv6-multicast: Fix memory leak in input path.
bnx2x: add missing break in bnx2x_dcbnl_get_cap
bnx2x: fix WOL by enablement PME in config space
bnx2x: fix hw attention handling
net: fix a typo in Documentation/networking/scaling.txt
ath9k: Fix a dma warning/memory leak
rtlwifi: rtl8192cu: Fix unitialized struct
iwlagn: fix dangling scan request
batman-adv: do_bcast has to be true for broadcast packets only
cfg80211: Fix validation of AKM suites
iwlegacy: do not use interruptible waits
iwlegacy: fix command queue timeout
ath9k_hw: Fix Rx DMA stuck for AR9003 chips
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use register name to initialize attention mask
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wrqu->encoding.length comes from the network administrator. It's
size u16. We want to limit "tocopy" to the smallest value of either
"len_keys", "wrqu->encoding.length" or 100. But because .length
gets cast from u16 to u8 we might use a random, smaller value than
the was desired. It's probably not very serious, but we may as well
fix it.
Btw, this is from code auditing and not from testing. I don't know
if this affects anyone in real life.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we cancel a scan, the completion runs
only from the workqueue. This can cause the
remain-on-channel scan to fail when another
one was just canceled, because we're still
aborting it.
To fix this, run the completion inline with
the lock still held before returning from
iwl_scan_cancel_timeout().
Also, to avoid the scan complete work from
completing a new scan prematurely, add a
new STATUS_SCAN_COMPLETE bit.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To make the next patch easier to read, move
the function up, it'll be needed earlier in
this file in the next patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We'll need to be able to run scan complete
inline, not from the workqueue, so refactor
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of iwl_scan_cancel_timeout()
isn't used anywhere, so let's just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only 5150 series devices report their temperature
in Kelvin, and for those we already convert it to
Celsius when storing into priv->temperature, so
there's no way priv->temperature will ever be in
Kelvin. Remove support for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an AP mode interface is added with a DTIM
period of two, the slot programming is wrong.
Fix it by taking into account the DTIM period.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If iwl_scan_initiate() fails for any reason,
priv->scan_request and priv->scan_vif are left
dangling. This can lead to a crash later when
iwl_bg_scan_completed() tries to run a pending
scan request.
In practice, this seems to be very rare due to
the STATUS_SCANNING check earlier. That check,
however, is wrong -- it should allow a scan to
be queued when a reset/roc scan is going on.
When a normal scan is already going on, a new
one can't be issued by mac80211, so that code
can be removed completely. I introduced this
bug when adding off-channel support in commit
266af4c745.
Cc: stable@kernel.org [3.0]
Reported-by: Peng Yan <peng.yan@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As everybody knows kcalloc checks the multiplication is safe and
that we don't run into overflow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the current code, the rate scaling isn't fed with
statistics from the BA notifications.
This is since my patch:
iwlagn: reclaim the packets in transport layer
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add debugging to show the status of probe in scan notification
to help debug probe related issues
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since all the queue logic has been moved to the transport layer,
the sequence number is set in the transport layer.
While doing that I forgot that the mac header is copied to the
TB of the TX cmd in the upper layer before the call to the transport
layer. So basically we used the sequence number from mac80211...
This was fine for the first assocation but after the second, mac80211
resets its counters while we don't hence a shift that led to terrible
impact on performance.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since priv->temperature is signed, we cannot use debugfs_create_u32
to refer to it.
Use a regular debugfs file instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Txid was used without being initialized.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After 'ath9k: optimize ath9k_ps_restore', it would only send the device to
network sleep and not to full sleep anymore, potentially causing more
battery drain.
Reported-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After handling command response, cmd skb is inserted into command
free queue(which keeps track of availabile skbs) for reuse purpose.
Skb length is not getting reset to zero here. This patch takes care
of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_channel_to_frequency() routine expects band parameter in
the form of "enum ieee80211_band band". Currently driver specific
band (BAND_A, BAND_AN etc.) is passed to the routine.
This patch makes sure that correct parameter is passed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In recent commit "mwifiex: use cfg80211 dynamic scan..."
(7c6fa2a843..) scan table handling in driver is removed to
make use of cfg80211 dynamic scan table. Now driver sends
beacon buffers found in scanning directly to stack and parse
the buffer for requested BSS only during association.
Beacon buffer doesn't contain bss band information. Driver
gets it from firmware in separate tlv (chan_band_tlv).
Currently since we don't inform stack about bss bandinfo,
there is an issue with 5GHz association.
Use "priv" field of struct cfg80211_bss to store bandinfo.
This fixes 5GHz association issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes association in 5GHz doesn't work. Dmesg log shows
"Can not find requested SSID xyz" error message. Currently
while preparing scan channel list for firmware Null entries
are created for disabled channels. The routine which retrieves
this list ignores channels after Null entry. Hence sometimes
driver doesn't scan the channel of requested AP and association
fails. The issue is fixed by avoiding those NULL entries.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When scanning for the broadcast SSID, there is no need to add the
SSID TLV (restoring the behaviour of the driver behaviour in the wext
days, confirmed in Marvell specifications).
If bssid is unspecified, the current scan code will usually fire off an
active scan probing for the specific requested SSID. However, if a scan
is ongoing (or has just finished), those scan results will be used
instead (even if that scan is totally different, e.g. a passive scan on
channel 4 for a different SSID). Fix this inconsistency by always
firing off a scan when associating without a bssid.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.
Update all the drivers that implement these callbacks.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this represents the bitmap of block ACK received after the
successful transmission of an aggregate frame. also made few
changes to beautify the display
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
