Pull ARM driver updates from Arnd Bergmann:
"There are a few separately maintained driver subsystems that we merge
through the SoC tree, notable changes are:
- Memory controller updates, mainly for Tegra and Mediatek SoCs, and
clarifications for the memory controller DT bindings
- SCMI firmware interface updates, in particular a new transport
based on OPTEE and support for atomic operations.
- Cleanups to the TEE subsystem, refactoring its memory management
For SoC specific drivers without a separate subsystem, changes include
- Smaller updates and fixes for TI, AT91/SAMA5, Qualcomm and NXP
Layerscape SoCs.
- Driver support for Microchip SAMA5D29, Tesla FSD, Renesas RZ/G2L,
and Qualcomm SM8450.
- Better power management on Mediatek MT81xx, NXP i.MX8MQ and older
NVIDIA Tegra chips"
* tag 'arm-drivers-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (154 commits)
ARM: spear: fix typos in comments
soc/microchip: fix invalid free in mpfs_sys_controller_delete
soc: s4: Add support for power domains controller
dt-bindings: power: add Amlogic s4 power domains bindings
ARM: at91: add support in soc driver for new SAMA5D29
soc: mediatek: mmsys: add sw0_rst_offset in mmsys driver data
dt-bindings: memory: renesas,rpc-if: Document RZ/V2L SoC
memory: emif: check the pointer temp in get_device_details()
memory: emif: Add check for setup_interrupts
dt-bindings: arm: mediatek: mmsys: add support for MT8186
dt-bindings: mediatek: add compatible for MT8186 pwrap
soc: mediatek: pwrap: add pwrap driver for MT8186 SoC
soc: mediatek: mmsys: add mmsys reset control for MT8186
soc: mediatek: mtk-infracfg: Disable ACP on MT8192
soc: ti: k3-socinfo: Add AM62x JTAG ID
soc: mediatek: add MTK mutex support for MT8186
soc: mediatek: mmsys: add mt8186 mmsys routing table
soc: mediatek: pm-domains: Add support for mt8186
dt-bindings: power: Add MT8186 power domains
soc: mediatek: pm-domains: Add support for mt8195
...
In commit d687e056a1 ("soc: mediatek: mmsys: Add mt8192 mmsys routing table"),
the mmsys routing table for mt8192 was introduced but the input selector
for DITHER->DSI0 has no value assigned to it.
This means that we are clearing bit 0 instead of setting it, blocking
communication between these two blocks; due to that, any display that
is connected to DSI0 will not work, as no data will go through.
The effect of that issue is that, during bootup, the DRM will block for
some time, while atomically waiting for a vblank that never happens;
later, the situation doesn't get better, leaving the display in a
non-functional state.
To fix this issue, fix the route entry in the table by assigning the
dither input selector to MT8192_DISP_DSI0_SEL_IN.
Fixes: d687e056a1 ("soc: mediatek: mmsys: Add mt8192 mmsys routing table")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220128142056.359900-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add MTK mutex support for MT8186 SoC.
We need MTK mutex to control timing of display modules and there
are two display pipelines for MT8186 including internal and external
display.
MTK mutex for internal display:
- Timing source: DSI
- Control modules: OVL0/RDMA0/COLOR0/CCORR/AAL0/GAMMA/POSTMASK0/DITHER
MTK mutex for external display:
- Timing source : DPI
- Control modules: OVL_2L0/RDMA1
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add new routing table for MT8186.
In MT8186, there are two routing pipelines for internal and external
display.
Internal display: OVL0->RDMA0->COLOR0->CCORR0->AAL0->GAMMA->POSTMASK0->
DITHER->DSI0
External display: OVL_2L0->RDMA1->DPI0
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This reverts commit 9de2b9286a ("ASoC: mediatek: Check for error clk
pointer").
With this patch in the tree, Chromebooks running the affected hardware
no longer boot. Bisect points to this patch, and reverting it fixes
the problem.
An analysis of the code with this patch applied shows:
ret = init_clks(pdev, clk);
if (ret)
return ERR_PTR(ret);
...
for (j = 0; j < MAX_CLKS && data->clk_id[j]; j++) {
struct clk *c = clk[data->clk_id[j]];
if (IS_ERR(c)) {
dev_err(&pdev->dev, "%s: clk unavailable\n",
data->name);
return ERR_CAST(c);
}
scpd->clk[j] = c;
}
Not all clocks in the clk_names array have to be present. Only the clocks
in the data->clk_id array are actually needed. The code already checks if
the required clocks are available and bails out if not. The assumption that
all clocks have to be present is wrong, and commit 9de2b9286a ("ASoC:
mediatek: Check for error clk pointer") needs to be reverted.
Cc: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Cc: Mark Brown <broonie@kernel.org>
Cc: James Liao <jamesjj.liao@mediatek.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Reported-by: Daniel Golle <daniel@makrotopia.org>
Fixes: 9de2b9286a ("ASoC: mediatek: Check for error clk pointer")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220207160923.3911501-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The UFOE (data compression engine) component needs to be enabled to have
the imgtec gpu driver working. If we don't enable it we see a black screen.
Looks like when we switched to use and array for setting the routing
registers in commit 440147639a ("soc: mediatek: mmsys: Use an array for
setting the routing registers") we missed to add this component in the new
routing table, it was present before that commit, so fix it by adding
this component in the mt8173 routing table.
Fixes: 440147639a ("soc: mediatek: mmsys: Use an array for setting the routing registers")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Eizan Miyamoto <eizan@chromium.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210625062448.3462177-1-enric.balletbo@collabora.com
[mb: taking into account mask value]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In this new power domain driver, when adding one power domain
it will prepare the dependent clocks at the same.
So we only do clk_bulk_enable/disable control during power ON/OFF.
When system suspend, the pm runtime framework will forcely power off
power domains. However, the dependent clocks are disabled but kept
prepared.
In MediaTek clock drivers, PLL would be turned ON when we do
clk_bulk_prepare control.
Clock hierarchy:
PLL -->
DIV_CK -->
CLK_MUX
(may be dependent clocks)
-->
SUBSYS_CG
(may be dependent clocks)
It will lead some unexpected clock states during system suspend.
This patch will fix by doing prepare_enable/disable_unprepare on
dependent clocks at the same time while we are going to power on/off
any power domain.
Fixes: 59b644b01c ("soc: mediatek: Add MediaTek SCPSYS power domains")
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: chun-jie.chen <chun-jie.chen@mediatek.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210601035905.2970384-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Mediatek requires mmsys clocks to be unprepared during suspend,
otherwise system has chances to hang.
syscon_regmap_lookup_by_phandle_optional() will attach and prepare the
first clock in smi node, leading to additional prepare to the clock
which is not balanced with the prepare/unprepare pair in resume/suspend
callbacks.
If a power domain node requests an smi node and the smi node's first
clock is an mmsys clock, it will results in an unstable suspend resume.
Fixes: f414854c88 ("soc: mediatek: pm-domains: Add SMI block as bus protection block")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: chun-jie.chen <chun-jie.chen@mediatek.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210601035905.2970384-2-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the power domains names to the power domain struct so we
have meaningful name for every power domain. This also removes the
following debugfs error message.
[ 2.242068] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
[ 2.249949] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
[ 2.257784] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
...
Fixes: 59b644b01c ("soc: mediatek: Add MediaTek SCPSYS power domains")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210225175000.824661-1-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
