No need to pass the dbgfs_dir just to assign it to mvm.
Assign to mvm and then call iwl_mvm_dbgfs_register.
This is a preparation towards the addition of a delayed
op_mode_start flow.
This will allow to split the op_mode_start flow.
Registration to debugfs must happen after we register to
mac80211 and the registration to mac80211 will soon be
delayed in certain cases. In order not to have to remember
the debugfs_dir in a separate variable, just set it into
the mvm structure so that it can be usable later.
Declare mvm->debugfs_dir in the iwl_mvm structure even when
IWLWIFI_DEBUGFS isn't enabled to simplify the source code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.a92ee491863d.I047923aa3598fbf4fb6fce2cdff75a4969fedd76@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlwifi patches intended for v5.12
* Check FW notification sizes for robustness;
* Improvements in the NAPI implementation;
* Implement a workaround for CCA-EXT;
* Add new FW API support;
* Fix a CSA bug;
* Implement PHY integration version parsing;
* A bit of refactoring;
* One more CSA bug fix, this time in the AP side;
* Support for new So devices and a bit of reorg;
* Per Platform Antenna Gain (PPAG) fixes and improvements;
* Improvements in the debug framework;
* Some other clean-ups and small fixes.
# gpg: Signature made Fri 05 Feb 2021 12:04:21 PM EET using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
We shouldn't trust the firmware with the sizes (or contents)
of notifications, accessing too much data could cause page
faults if the data doesn't fit into the allocated space. This
applies more on older NICs where multiple notifications can
be in a single RX buffer.
Add a general framework for checking a minimum size of any
notification in the RX handlers and use it for most. Some RX
handlers were already checking and I've moved the checks,
some more complex checks I left and made them _NO_SIZE for
the RX handlers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.3e155d5e5f90.I2121fa4ac7cd7eb98970d84b793796646afa3eed@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A FTM responder may do PASN authentication with unassociated stations
to allow secure ranging. In this case, the driver will add an internal
station and install the TK so the FW will accept protected FTM
request frames from this station and will send a protected FTM
response frame.
In addition, the driver needs to configure the HLTK to the FW so
the FW can derive the secure LTF bits. This is left for a later
patch since it is not yet supported by the FW.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.c915b44ad7dd.I72ef7f9753964555561c27ec503241105eddb14e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have a lot of mostly duplicated data structures that are repeated
only because the device name string is different. To avoid this, move
the string from the cfg to the trans structure and add it
independently from the rest of the configuration to the PCI mapping
tables.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is dead code, nothing uses the IWL_DEVICE_22560 macro and
thus nothing every uses IWL_DEVICE_FAMILY_22560. Remove it all.
While at it, remove some code and definitions used only in this
case, and clean up some comments/names that still refer to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware has now a new session protection command.
This new API allows the firmware to manage the protection
needed for association. It'll also remove the event when
the association is complete.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During D3 state there are some flows which requires FW reset.
Add new API to support it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove periodic trigger functionality.
After moving to the new API we will add periodic trigger functionality
that matches the new API.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support code to be able to use the DRAM buffer allocation command,
which allows us to send information about a buffer to the firmware
to use it with the DBGC hardware.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the "apply points" mechanism as preparation for the changed
debug API where this is now a "time point" instead. Use a new API
across the code at the trigger points ("time points"), but don't
yet implement it since that requires some more preparation.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In prior hardware generations (e.g. 9000 series), we received the BAR
frame with fake NSSN information to handle releasing frames from the
reorder buffer for the default queue, the other queues were getting
the FRAME_RELEASE notification in this case.
With multi-TID block-ack, the firmware no longer sends us the BAR
frame because the fake RX is quite big (just the metadata is around
48 bytes or so). Instead, it now sends us one (or multiple) special
release notifications (0xc2). The hardware consumes these as well,
but only generates the FRAME_RELEASE (0xc3) for queues other than
the default queue. We thus need to handle them in the same way we
handle the normal FRAME_RELEASE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If mvm->fwrt.cur_fw_img != IWL_UCODE_INIT, then
rfkill_safe_init_done must be true since
rfkill_safe_init_done is set to true before we start to load
the runtime image.
Remove the redundant condition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We will soon be using a new notification that will be
initiated by the driver, sent to the firmware and sent
back to all the RSS queues by the firmware. This new
notification will be useful to synchronize the NSSN across
all the queues.
For now, don't send the notification, just add the code to
handle it. Later patch will add the code to actually send
it.
While at it, validate the baid coming from the firmware to
avoid accessing an array with a bad index in the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
