The commit 16ada730a7 ("mmc: sdhci-of-arasan: Modify clock operations
handling") introduced support for platform specific clock operations.
Around the same point in time the commit 36c6aadaae ("mmc:
sdhci-of-arasan: Add support for Intel Keem Bay") was also merged.
Unfortunate it was not really tested on top of the previously mentioned
commit, which causes clock registration failures for Keem Bay SOC devices.
Let's fix this, by properly declaring the clock operation for Keem Bay SOC
devices.
Fixes: 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201118120120.24908-2-muhammad.husaini.zulkifli@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mmc/host/sdhci-st.c:512:34: warning:
‘st_sdhci_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162344.485921-2-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mmc/host/sdhci-sprd.c:723:34: warning:
‘sdhci_sprd_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20201120162344.485921-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A UHS setting of SDR25 can give better results for High Speed mode.
This is because there is no setting corresponding to high speed. Currently
SDHCI sets no value, which means zero which is also the setting for SDR12.
There was an attempt to change this in sdhci.c but it caused problems for
some drivers, so it was reverted and the change was made to sdhci-brcmstb
in commit 2fefc7c5f7 ("mmc: sdhci-brcmstb: Fix incorrect switch to HS
mode"). Several other drivers also do this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v5.4+
Link: https://lore.kernel.org/r/20201112133656.20317-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
pic32_sdhci_probe_platform() always returned 0, so there's no reason for
a return value. In addition, pic32_sdhci_probe() checked the return value
for possible error which is unnecessary.
Convert pic32_sdhci_probe_platform() to a void function and remove the
return value check. Fix the following Coccinelle warning:
./drivers/mmc/host/sdhci-pic32.c:127:5-8: Unneeded variable: "ret". Return "0" on line 137
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1604847648-13036-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/mmc/host/meson-gx-mmc.c:1252:34: warning:
‘meson_mmc_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201103163046.14336-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RTS5261 support SD mode and PCIe/NVMe mode. The workflow is as follows.
1.RTS5261 work in SD mode and set MMC_CAPS2_SD_EXP flag.
2.If card is plugged in, Host send CMD8 to ask card's PCIe availability.
3.If the card has PCIe availability and WP is not set, init_sd_express() will be invoked,
RTS5261 switch to PCIe/NVMe mode.
4.Mmc driver handover it to NVMe driver.
5.If card is unplugged, RTS5261 will switch to SD mode.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Link: https://lore.kernel.org/r/1603936703-3403-1-git-send-email-rui_feng@realsil.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the SD specification v7.10 the SD express card has been added. This new
type of removable SD card, can be managed via a PCIe/NVMe based interface,
while also allowing backwards compatibility towards the legacy SD
interface.
To keep the backwards compatibility, it's required to start the
initialization through the legacy SD interface. If it turns out that the
mmc host and the SD card, both supports the PCIe/NVMe interface, then a
switch should be allowed.
Therefore, let's introduce some basic support for this type of SD cards to
the mmc core. The mmc host, should set MMC_CAP2_SD_EXP if it supports this
interface and MMC_CAP2_SD_EXP_1_2V, if also 1.2V is supported, as to inform
the core about it.
To deal with the switch to the PCIe/NVMe interface, the mmc host is
required to implement a new host ops, ->init_sd_express(). Based on the
initial communication between the host and the card, host->ios.timing is
set to either MMC_TIMING_SD_EXP or MMC_TIMING_SD_EXP_1_2V, depending on if
1.2V is supported or not. In this way, the mmc host can check these values
in its ->init_sd_express() ops, to know how to proceed with the handover.
Note that, to manage card insert/removal, the mmc core sticks with using
the ->get_cd() callback, which means it's the host's responsibility to make
sure it provides valid data, even if the card may be managed by PCIe/NVMe
at the moment. As long as the card seems to be present, the mmc core keeps
the card powered on.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Rui Feng <rui_feng@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1603936636-3126-1-git-send-email-rui_feng@realsil.com.cn
This change will allow platform designers better control over signal
integrity by allowing them to tune the HS200 and HS400 driver strengths.
The driver strength was previously hard coded to A to solve boot
problems with certain platforms. This driver strength does not
universally apply to all platforms so we need a knob to adjust it.
All older platforms currently have the SDR104 preset hard coded to A in
the firmware. This means that switching from the hard coded value in
the kernel to reading the SDR104 preset is a no-op for these platforms.
Newer platforms will have properly set presets. So this change will
support both new and old platforms.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Victor Ding <victording@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201027084612.528301-1-victording@google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via DT table so it should be always used and
the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant for sunxi). This
fixes compile warning:
drivers/mmc/host/sunxi-mmc.c:1181:34: warning: ‘sunxi_mmc_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201026153810.89512-3-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver uses GPIO Descriptor Consumer Interface so include proper
header to fix compile test errors like:
drivers/mmc/host/s3cmci.c: In function ‘s3cmci_check_sdio_irq’:
drivers/mmc/host/s3cmci.c:304:7: error:
implicit declaration of function ‘gpiod_get_value’; did you mean ‘gpio_get_value’? [-Werror=implicit-function-declaration]
drivers/mmc/host/s3cmci.c: In function ‘s3cmci_probe_pdata’:
drivers/mmc/host/s3cmci.c:1451:19: error:
implicit declaration of function ‘devm_gpiod_get_index’ [-Werror=implicit-function-declaration]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201026153810.89512-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
