When running with OP-TEE, the suspend control is handled securely.
Suspend can be entered using PSCI support. Since the sama5d2 supports
multiple suspend modes, add a new CONFIG_ATMEL_SECURE_PM which will
send a SMC call to select the suspend mode at init time.
"atmel.pm_modes" boot argument is still supported for compatibility
purposes but the standby value is actually ignored since PSCI suspend
is used and it only support one mode (suspend).
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
SoCs supporting ULP0 or ULP1 modes and variants of Cadence Ethernet IP
(controlled by macb driver) may behave buggy when Wake-on-Lan (WoL) is
configured and WoL packet is received while in ULP0/ULP1. On some SoCs
Ethernet interface is not working after resume. On other SoCs the CPU
goes to abort on resume path when switching execution from internal SRAM
to DRAM. For ULP1 + WoL the issue is related a particular restart
sequence of the internal clocks when resuming. These clocks are
automatically managed by PMC and may happen that GMAC peripheral clock
is restarted few clock cycles before internal clocks causing blocking
of Ethernet's DMA. As a consequence Ethernet TX transactions are stopped
and RX transactions are partially stopped (packets are received by MAC,
RX counters incremented but the data is not transferred to DRAM). The
workaround for this is to disable Ethernet's peripheral clock when
going to ULP1. Same behavior has been reproduced on ULP0 for some
platforms (SAMA5D2, SAMA5D3) and the same workaround solves the issue.
The problem has been solved on pm.c as quirk to avoid polluting the
MACB driver with AT91 specific issues as this driver is generic to
multiple vendors.
At probe pointers to struct device_node are retrieved and on the
at91_pm_enter() the quirk specifics are applied: for all Ethernet
interfaces that were parsed the peripheral clocks are disabled. A
special handling is done for modes in dns_modes mask as these are
considered modes that blocks the system if WoL packet are received
but for which applying quirk will lead to not waking up on WoL
packets: in situation where Ethernet interface(s) has suspend mode
in dns_modes mask and Ethernet interface(s) is the only available
wakeup source the suspend is canceled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Use kernel documentation style. Along with it fix the naming of
struct at91_pm_sfrbu_regs in documentation.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Introduce macros to replace standby/suspend mode if they depends on
controllers that failed to map (or other errors). Macros keep track
of the complementary mode to avoid having set the same AT91 PM mode
for both suspend and standby.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Backup area is now switched to VDDIN33 at boot (with the help of
bootloader). When switching to backup mode we need to switch backup area
to VBAT as all the other power sources are cut off. The resuming from
backup mode is done with the help of bootloader, so there is no need to
do something particular in Linux to restore backup area power source.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210830100927.22711-1-claudiu.beznea@microchip.com
The resuming from backup mode is done with the help of bootloader.
The bootloader reconfigure the DDR controller and DDR PHY controller.
To speed-up the resuming process save the PHY calibration data into
SECURAM before suspending (securam is powered on backup mode).
This data will be later used by bootloader in DDR PHY reconfiguration
process. Also, in the process or recalibration the first 8 words of
the memory may get corrupted. To solve this, these 8 words are saved
in the securam and restored by bootloader in the process of PHY
configuration.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-20-claudiu.beznea@microchip.com
at91_pm_modes_init() checks for proper nodes in device tree and maps
them accordingly. Up to SAMA7G5 all AT91 SoCs had the same mapping
b/w power saving modes and different controllers needed in the
final/first steps of suspend/resume. SAMA7G5 is not aligned with the
old SoCs thus the code is adapted for this. This patch prepares
the field for next commits.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-5-claudiu.beznea@microchip.com
ULP0 fast improves suspend/resume time with few milliseconds the drawback
being the power consumption. The mean values measured for suspend/resume
time are as follows (measured on SAMA5D2 Xplained board), ULP0 compared
with fast ULP0:
- ulp0 fast: suspend time: 169 ms, resume time: 216 ms
- ulp0 : suspend time: 197 ms, resume time: 258 ms
Current consumption while suspended (measured on SAMA5D2 Xplained board):
- ulp0 fast: 730uA
- ulp0 : 270uA
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1596616610-15460-2-git-send-email-claudiu.beznea@microchip.com
SAM9X60's PMC has different master clock register offset than the other
SoCs' PMC. Due to this, specify master clock register offset based
on PMC compatible and pass it to pm_suspend.S since it is also needed
in there. When PM part for SAM9X60 was published the SAM9X60's PMC
(commit f6deae46039c ("clk: at91: add sam9x60 pmc driver")) wasn't
integrated.
Fixes: 01c7031cfa ("ARM: at91: pm: initial PM support for SAM9X60")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1579522208-19523-2-git-send-email-claudiu.beznea@microchip.com
AT91 SoC for 5.3
- fix a pm.c warning with W=1
* tag 'at91-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
arm: add missing include platform-data/atmel.h
Signed-off-by: Olof Johansson <olof@lixom.net>
Include corresponding headerfile <linux/platform-data/atmel.h> for
function at91_suspend_entering_slow_clock().
../arch/arm/mach-at91/pm.c:279:5: warning: no previous prototype for ‘at91_suspend_entering_slow_clock’ [-Wmissing-prototypes]
int at91_suspend_entering_slow_clock(void)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Philippe Mazenauer <philippe.mazenauer@outlook.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AT91 SoC for 5.2
- PM changes for SAM9X60
* tag 'at91-5.2-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: at91: pm: do not disable/enable PLLA for ULP modes
ARM: at91: pm: disable RC oscillator in ULP0
ARM: at91: pm: add ULP1 support for SAM9X60
ARM: at91: pm: add support for per SoC wakeup source configuration
ARM: at91: pm: keep at91_pm_backup_init() only for SAMA5D2 SoCs
ARM: at91: pm: initial PM support for SAM9X60
dt-bindings: arm: atmel: add binding for SAM9X60 SoC
ARM: at91: pm: introduce at91_soc_pm structure
Signed-off-by: Olof Johansson <olof@lixom.net>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device. When returning error we should
call put_device.
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Add support for per SoC wakeup source configuration. In this way
we could have per SoC wakeup sources, shutdown controller and power
management controller configurations for ULP1 power management mode.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
To have per SoC PM information add a new structure which embed
a member of type struct at91_pm_data. This will allow easy addition
of new information without contaminate struct at91_pm_data that is
passed to the last phase suspend function (at91_suspend_sram_fn).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
of_find_device_by_node takes a reference to the struct device when it
finds a match via get_device. but it fails to put_device in
at91_pm_config_ws, for_each_matching_node_and_match will get and put
the node properly, there is no need to call the of_put_node. Therefore,
just call put_device instead of of_node_put in at91_pm_config_ws.
Fixes: d7484f5c6b ("ARM: at91: pm: configure wakeup sources for ULP1 mode")
Suggested-by: Claudiu Beznea <Claudiu.Beznea@microchip.com>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There is no need to initialize pm_bu since it is used only if backup
mode is selected. In case backup mode initialization fails (which means
pm_bu is invalid) the ULP0 mode will be selected.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
Since for ULP1 PM mode of SAMA5D2 the wakeup sources are limited and
well known add a method to check if these wakeup sources are defined by
user (either via DT or filesystem). In case there are no wakeup sources
defined for ULP1 the PM suspend will fail, otherwise these will be
configured in fast startup registers of PMC. Since wakeup sources of
ULP1 need also to be configured in SHDWC registers the code was a bit
changed to map the SHDWC also in case ULP1 is requested by user (this
was done in the initialization phase). In case the ULP1 initialization
fails the ULP0 mode is used (this mode was also used in case backup mode
initialization failed).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the ULP1 mode, in order to achieve the lowest power consumption
with the system in retention mode and be able to resume on the wake
up events, all the clocks are shut off, inclusive the embedded 12MHz
RC oscillator, and the number of wake up sources is limited as well.
When the wake up event is asserted, the embedded 12MHz RC oscillator
restarts automatically.
The ULP1 (Ultra Low-power mode 1) is introduced by SAMA5D2.
The previous size of pm_suspend.o was 2148 bytes. With the addition of
ULP1 mode the new size of pm_suspend.o raised at 2456 bytes.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[claudiu.beznea@microchip.com: aligned with 4.18-rc1]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add more compatibles to be able to correct the USB clock detection.
at91sam9261 and at91sam9263 have the same PMC_SCSR layout as at91sam9260.
at91sam9rl doesn't have any USB clock.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The PM code wrongly uses virt_to_phys() instead of __pa_symbol() and was
not updated by commit 64fc2a947a ("ARM: 8641/1: treewide: Replace uses of
virt_to_phys with __pa_symbol") because it was not yet in tree.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
