[Why]
DPALT detection for B0 PHY has its own set of RDPCSPIPE registers
[How]
Use RDPCSPIPE registers to detect if DPALT lane is 4 lane
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Hansen <Hansen.Dsouza@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The existing limit was mistakenly bigger than 4k for DCN 3.1
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current FPU code for DCN2x is located under dml/dcn2x.
This is not aligned with DC's general source tree
structure.
[How]
Move FPU code for DCN2x to dml/dcn20.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Overriding link setting inside override_training_settings
result in fallback link settings being ignored. This can
potentially cause link training to always fail and consequently
result in an infinite loop of link training to occur in
dp_verify_link_cap during detection.
[How]
Since preferred link settings are already considered inside
decide_link_settings, skip the check in override_training_settings
to avoid infinite link training loops.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Depends on DRM_AMDGPU_SI and DRM_AMD_DC
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
YELLOW_CARP_B0 address was not correct
[How]
Set YELLOW_CARP_B0 to 0x1A.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Jude Shih <shenshih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
DCN3 B0 has a mux, which redirects PHYC and PHYD to PHYF and PHYG.
[How]
Fix DIG mapping.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
(cherry picked from commit 4b7786d87f)
[Why]
Starting from B0, along with RDPCSTX, RDPCSPIPE registers are also used.
[How]
Make sure RDPCSPIPE registers are programmed correctly.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
(cherry picked from commit bdd1a21b52)
Depends on DRM_AMDGPU_SI and DRM_AMD_DC
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Running into bugchecks during stress test where rptr is 0xFFFFFFFF.
Typically this is caused by a hard hang, and can come from HW outside
of DCN.
[How]
To prevent bugchecks when writing the DMUB rptr, fist check that the
rptr is valid.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow us to query instances versions more cleanly.
Instancing support is not consistent unfortunately. SDMA is a
good example. Sienna cichlid has 4 total SDMA instances, each
enumerated separately (HWIDs 42, 43, 68, 69). Arcturus has 8
total SDMA instances, but they are enumerated as multiple
instances of the same HWIDs (4x HWID 42, 4x HWID 43). UMC
is another example. On most chips there are multiple
instances with the same HWID. This allows us to support both
forms.
v2: rebase
v3: clarify instancing support
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise, we will run into error case path.
v2: fix build when CONFIG_DRM_AMD_DC_DCN is not set
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use IP versions rather than asic_type to differentiate
IP version specific features.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use IP versions rather than asic_type to differentiate
IP version specific features.
v2: drop unrelated change
Acked-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some reason we're defining DP 2.0 definitions inside our
driver. Now that patches to introduce relevant definitions
are slated to be merged into drm-next this is causing conflicts.
In file included from drivers/gpu/drm/amd/amdgpu/amdgpu_bo_list.c:33:
In file included from ./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgpu.h:70:
In file included from ./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgpu_mode.h:36:
./include/drm/drm_dp_helper.h:1322:9: error: 'DP_MAIN_LINK_CHANNEL_CODING_PHY_REPEATER' macro redefined [-Werror,-Wmacro-redefined]
^
./drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dp_types.h:881:9: note: previous definition is here
^
1 error generated.
[How]
Guard all display driver defines with #ifndef for now. Once we pull
in the new definitions into amd-staging-drm-next we will follow
up and drop definitions from our driver and provide follow-up
header updates for any addition DP 2.0 definitions required
by our driver.
We also ensure drm_dp_helper.h is included before dc_dp_types.h.
v3: Ensure drm_dp_helper.h is included before dc_dp_types.h
v2: Add one missing endif
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
add display related cyan_skillfish files in.
makefile controlled by CONFIG_DRM_AMD_DC_DCN201 flag.
v2: squash in clang fixes from Harry, Nathan
v3: squash in missing CONFIG_DRM_AMD_DC check (Alex)
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Jun Lei <jun.lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The two AMD drivers have their own custom offsetof() implementation
that now triggers a warning with recent versions of clang:
drivers/gpu/drm/radeon/radeon_atombios.c:133:14: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
Change all the instances to use the normal offsetof() provided
by the kernel that does not have this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pci deviceid not passed to dal dc, without proper break,
dcn2.x falls into dcn3.x code path
[how]
pass in pci deviceid, and break once dal_version initialized.
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recently debugging efforts have involved setting/checking the
X.Y value used during payload allocation. Current output for
Y was calculated with incorrect bitshift. Y value is also not
human readable.
[How]
Refactor logging into separate function. Fix Y calculation error
and format output to be human readable.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Theoretically rare corner case where ceil(Y) results in rounding
up to an integer. If this happens, the 1 should be carried over to
the X value.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is a chance verified link cap can be greater than max link cap.
This causes software hang because we cannot power up PHY with link rate
that cannot handle.
The change is to guard verfieid link cap from becoming larger than max link cap
our PHy can support.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Stack variable params.backlight_ramping_override is uninitialized, so it
contains junk data
[How]
Initialize the variable to false
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Blnd, 3dlut, and shaper LUT select registers are double buffered, however
their accompanying LUT memory shutdown registers are not. As a result,
shutting down LUT memory immediately after setting a block to bypass causes
corruption as bypass only happens at next Vupdate.
[HOW]
Re-enable mem low power for CM block
Force optimization on next flip and disable LUT memory during optimization
sequence if LUT select field is then set to bypass
v2: squash in CONFIG_DRM_AMD_DC_DCN fix (Alex)
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pci deviceid not passed to dal dc, without proper break,
dcn2.x falls into dcn3.x code path
[how]
pass in pci deviceid, and break once dal_version initialized.
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Stack variable params.backlight_ramping_override is uninitialized, so it
contains junk data
[How]
Initialize the variable to false
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
ASSR is dependent on Signed PSP Verstage to enable Content
Protection for eDP panels. Unsigned PSP verstage is used
during development phase causing ASSR to FAIL.
As a result, link training is performed with
DP_PANEL_MODE_DEFAULT instead of DP_PANEL_MODE_EDP for
eDP panels that causes display flicker on some panels.
[How]
- Do not change panel mode, if ASSR is disabled
- Just report and continue to perform eDP link training
with right settings further.
Signed-off-by: Praful Swarnakar <Praful.Swarnakar@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
DC should be used in place of DAL in
upstream.
[How]
Replace dal with dc in function names.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fixes to backlight, LUT, PPS, MST
- Use correct vpg for 128b/132b encoding
- Improved logging for VCP
- Replace referral of dal with dc
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Oliver Logush <oliver.logush@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change is needed for DCN2 to make use of the immediate_update
flag. With this flag, update to PPS will be immediate, rather than
always taking place on dig_update signal.
[How]
Set AFMT_GENERIC7_FRAME/IMMEDIATE_UPDATE bits depending on flag
value.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Ilya <Ilya.Bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MST streams share the same link and should share the same encoder.
The current availability check may erroneously determine that an
encoder is unavailable for MST streams.
[How]
When checking for link encoder availability, check if an encoder
in use shares a link with the stream for which the availability
check is being conducted. If the link is shared, then the link
encoder should be shared too and will be deemed available.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Link encoder in the link could be null for certain links.
[How]
If link encoder in the link is null then get the link encoder
from the stream.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Unify the code which handles the conversion between hw lane setting
and dpcd lane setting.
v2: squash in unused variable fixes (Alex)
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To support per lane lane setting adjustment, we need to change cur_lane_setting
to an array one for each lane as the first step.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Requested feature to assist with Thermal, Acoustic, Power, and
Performance tuning.
[How]
Add a debug field that will override calculated minimum DRAM clock,
if the debug value is larger than the calculate value.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prevent unnecessary wake up of DMCUB when ABM is enabled without PSR
enabled, driver will notify DMCUB to stop ABM's vertical interrupts
if vsync is disabled and steady state is reached.
[How]
Send inbox message to notify ABM pause based on vsync on/off
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
AFMT is unused for DP audio, so powering it on for DP is unnecessary.
[HOW]
APG block should be powered down instead, however HW defaults to shutdown
state when not enabled so no further work is required.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
128b/132b uses the vpg instance assigned to hpo dp stream encoder.
The current vpg used is assigned to dio stream encoder.
This is incorrect and cause display black screen because the
actual vpg is powered off.
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ASSR is dependent on Signed PSP Verstage to enable Content
Protection for eDP panels. Unsigned PSP verstage is used
during development phase causing ASSR to FAIL.
As a result, link training is performed with
DP_PANEL_MODE_DEFAULT instead of DP_PANEL_MODE_EDP for
eDP panels that causes display flicker on some panels.
[How]
- Do not change panel mode, if ASSR is disabled
- Just report and continue to perform eDP link training
with right settings further.
Signed-off-by: Praful Swarnakar <Praful.Swarnakar@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using an empty macro expansion as a conditional expression
produces a W=1 warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c: In function 'dce_aux_transfer_with_retries':
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:775:156: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
775 | "dce_aux_transfer_with_retries: AUX_RET_SUCCESS: AUX_TRANSACTION_REPLY_I2C_OVER_AUX_DEFER");
| ^
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:783:155: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
783 | "dce_aux_transfer_with_retries: AUX_RET_SUCCESS: AUX_TRANSACTION_REPLY_I2C_OVER_AUX_NACK");
| ^
Expand it to "do { } while (0)" instead to make the expression
more robust and avoid the warning.
Fixes: 56aca23093 ("drm/amd/display: Add AUX I2C tracing.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, the 32bit kernel build fails due to an incorrect string
format specifier. ARRAY_SIZE() returns size_t type as it uses sizeof().
However, we specify it in a string as %ld. This causes a compiler error
and causes the 32bit build to fail.
[How]
Change the %ld to %zu as size_t (which sizeof() returns) is an unsigned
integer data type. We use 'z' to ensure it also works with 64bit build.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Hayden Goodfellow <Hayden.Goodfellow@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This new DC version brings improvements in the following areas:
- New firmware version
- Fix HPD problems on DCN2
- Fix generic encoder problems and null deferences
- Adjust DCN301 watermark
- Rework dynamic bpp for DCN3x
- Improve link training fallback logic
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Links which are dynamically assigned link encoders have their link
encoder set to NULL.
[How]
Check that a pointer to a link_encoder object is non-NULL before using
it.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need a bit for x86 driver to enable a FW boot option for an upcoming
feature.
[How]
Added a bit in dmub_fw_boot_options for an upcoming feature.
Reviewed-by: Jimmy Kizito <jimmy.kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DIG mapping change is causing a blocker
[How]
Revert the change for now. We will re-implement it later.
Reviewed-by: Jimmy Kizito <jimmy.kizito@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from B0, along with RDPCSTX, RDPCSPIPE registers are also used.
[How]
Make sure RDPCSPIPE registers are programmed correctly.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently causes visible flicker in some scenarios on OLED eDPs
Reviewed-by: Haonan Wang <haonan.wang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
Screen sometimes would have artifacts or blink once at the time when bpp
is dynamically changed.
How:
1. Changed to update PPS infopacket in frame mode instead of immediate mode
since other updates for bpp change are double-buffered.
2. Changed double-buffering enablement programming for DCN30 as advised by
ASIC team
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bing Guo <Bing.Guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If DCN30 watermark calc is used for DCN301, the calculated values are
wrong due to the data structure mismatch between DCN30 and DCN301.
However, using the original DCN301 watermark values causes underflow.
[how]
- Add DCN21-style watermark calculations
- Adjust DCN301 watermark values to remove the underflow
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The change of setting a timer callback on boot for 10 seconds is still
working, just lost power down on boot and power down for DCN3.
[How]
Added power down on boot and power down for DCN3.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect encoder assignments were being used while applying a new state
to hardware.
(1) When committing a new state to hardware requires resetting the
back-end, the encoder assignments of the current or old state should be
used when disabling the back-end; and the encoder assignments for the
next or new state should be used when re-enabling the back-end.
(2) Link training on hot plug could take over an encoder already in use
by another stream without first disabling it.
[How]
(1) Introduce a resource context 'link_enc_cfg_context' which includes:
- a mode to indicate when transitioning from current to next state.
- transient encoder assignments to use during this state transition.
Update the encoder configuration interface to respond to queries about
encoder assignment based on the mode of operation.
(2) Check if an encoder is already in use before attempting to perform
link training on hot plug.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Trying to enable multiple displays simultaneously exposed shortcomings
with the algorithm for dynamic link encoder assignment.
The main problems were:
- Assuming stream order remained constant across states would sometimes
lead to invalid DIG encoder assignment.
- Incorrect logic for deciding whether or not a DIG could support a
stream would also sometimes lead to invalid DIG encoder assignment.
- Changes in encoder assignment were wholesale while updating of the
pipe backend is incremental. This would lead to the hardware state not
matching the software state even with valid encoder assignments.
[How]
The following changes fix the identified problems.
- Use stream pointer rather than stream index to track streams across
states.
- Fix DIG compatibility check by examining the link signal type rather
than the stream signal type.
- Modify assignment algorithm to make incremental updates so software
and hardware states remain coherent.
Additionally:
- Add assertions and an encoder assignment validation function
link_enc_cfg_validate() to detect potential problems with encoder
assignment closer to their root cause.
- Reduce the frequency with which the assignment algorithm is executed.
It should not be necessary for fast state validation.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Link training should fail if stream bandwidth exceeds link bandwidth.
[How]
Correct fallback logic and use named variables to make intention clear.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN3 B0 has a mux, which redirects PHYC and PHYD to PHYF and PHYG.
[How]
Fix DIG mapping.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD disable and enable sequences are not mutually exclusive on Linux.
For HPDs that spans under 1s (i.e. HPD low = 1s), part of the disable
sequence (specifically, a request to SMU to lower refclk) could come
right before the call to PHY enablement, causing DMUB to access an
irresponsive PHY and thus a hard hang on the system.
[How]
Disable 48mhz refclk off when there is any HPD status in connected state
for dcn20.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
With Werror enabled in the kernel we were failing the clang build since
dml21_ModeSupportAndSystemConfigurationFull's stack frame is 1064 when
building with clang, and exceeding the default 1024 stack frame limit.
The culprit seems to be the Pipe struct, so pull the relevant block
out into its own sub-function.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
dcn_bw_calc_rq_dlg_ttu uses a stack frame great than 1024. To solve this
we could allocate the rq_param, dlg_sys_param, and input structs
dynamically. Since this function is inside a kernel_fpu_begin()/end()
call we want to avoid memory allocation. Instead it's much
safer to pre-allocate these on the pipe_ctx.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Fixes: 3fe617ccaf ("Enable '-Werror' by default for all kernel builds")
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Xinhui Pan <Xinhui.Pan@amd.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: llvm@lists.linux.dev
Acked-by: Christian König <christian.koenig@amd.com>
Build-tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Passing structs adds a lot of overhead. We don't ever want to pass
anything bigger than primitives by value.
This patch fixes these Coverity IDs:
Addresses-Coverity-ID: 1424031: ("Big parameter passed by value")
Addresses-Coverity-ID: 1424055: ("Big parameter passed by value")
Addresses-Coverity-ID: 1424072: ("Big parameter passed by value")
Addresses-Coverity-ID: 1423779: ("Big parameter passed by value")
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Xinhui Pan <Xinhui.Pan@amd.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: llvm@lists.linux.dev
Acked-by: Christian König <christian.koenig@amd.com>
Build-tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Passing structs adds a lot of overhead. We don't ever want to pass
anything bigger than primitives by value.
This patch fixes these Coverity IDs:
Addresses-Coverity-ID: 1423868: ("Big parameter passed by value")
Addresses-Coverity-ID: 1423870: ("Big parameter passed by value")
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Xinhui Pan <Xinhui.Pan@amd.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: llvm@lists.linux.dev
Acked-by: Christian König <christian.koenig@amd.com>
Build-tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This neither needs to be on the stack nor passed by value
to each function call. In fact, when building with clang
it seems to break the Linux's default 1024 byte stack
frame limit.
[How]
We can simply pass this as a const pointer.
This patch fixes these Coverity IDs
Addresses-Coverity-ID: 1424031: ("Big parameter passed by value")
Addresses-Coverity-ID: 1423970: ("Big parameter passed by value")
Addresses-Coverity-ID: 1423941: ("Big parameter passed by value")
Addresses-Coverity-ID: 1451742: ("Big parameter passed by value")
Addresses-Coverity-ID: 1451887: ("Big parameter passed by value")
Addresses-Coverity-ID: 1454146: ("Big parameter passed by value")
Addresses-Coverity-ID: 1454152: ("Big parameter passed by value")
Addresses-Coverity-ID: 1454413: ("Big parameter passed by value")
Addresses-Coverity-ID: 1466144: ("Big parameter passed by value")
Addresses-Coverity-ID: 1487237: ("Big parameter passed by value")
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Fixes: 3fe617ccaf ("Enable '-Werror' by default for all kernel builds")
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Xinhui Pan <Xinhui.Pan@amd.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: llvm@lists.linux.dev
Acked-by: Christian König <christian.koenig@amd.com>
Build-tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using an empty macro expansion as a conditional expression
produces a W=1 warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c: In function 'dce_aux_transfer_with_retries':
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:775:156: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
775 | "dce_aux_transfer_with_retries: AUX_RET_SUCCESS: AUX_TRANSACTION_REPLY_I2C_OVER_AUX_DEFER");
| ^
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:783:155: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
783 | "dce_aux_transfer_with_retries: AUX_RET_SUCCESS: AUX_TRANSACTION_REPLY_I2C_OVER_AUX_NACK");
| ^
Expand it to "do { } while (0)" instead to make the expression
more robust and avoid the warning.
Fixes: 56aca23093 ("drm/amd/display: Add AUX I2C tracing.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
DC core is being released from DM before it's referenced
from hpd_rx wq destruction code.
How: Move hpd_rx destruction before DC core destruction.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some games, ie. Doom Eternal, present from compute following compute
post-fx and would benefit from having DCC image stores available.
DCN on gfx10_3 doesn't need INDEPENDENT_128B_BLOCKS = 0 so we can expose
these modifiers capable of DCC image stores.
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds the missing logic to set the correct value of dcc_ind_blk for this tiling version.
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't need to do this workaround if we start setting this value when we fill the plane attributes.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The "base_addr_is_mc_addr" field was added for dcn3.1 support but
pa_config was never updated to set it to false.
Uninitialized memory causes it to be set to true which results in
address mistranslation and white screen.
[How]
Use memset to ensure all fields are initialized to 0 by default.
Fixes: 64b1d0e8d5 ("drm/amd/display: Add DCN3.1 HWSEQ")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch allows panel orientation quirks from DRM core to be
used. They attach a DRM connector property "panel orientation"
which indicates in which direction the panel has been mounted.
Some machines have the internal screen mounted with a rotation.
Since the panel orientation quirks need the native mode from the
EDID, check for it in amdgpu_dm_connector_ddc_get_modes.
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The "base_addr_is_mc_addr" field was added for dcn3.1 support but
pa_config was never updated to set it to false.
Uninitialized memory causes it to be set to true which results in
address mistranslation and white screen.
[How]
Use memset to ensure all fields are initialized to 0 by default.
Fixes: 64b1d0e8d5 ("drm/amd/display: Add DCN3.1 HWSEQ")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This patch allows panel orientation quirks from DRM core to be
used. They attach a DRM connector property "panel orientation"
which indicates in which direction the panel has been mounted.
Some machines have the internal screen mounted with a rotation.
Since the panel orientation quirks need the native mode from the
EDID, check for it in amdgpu_dm_connector_ddc_get_modes.
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If link training is aborted, it shall be retried if sink is present.
[How]
Check hpd status to find out whether sink is present or not. If sink is
present, then link training shall be tried again with same settings.
Otherwise, link training shall be aborted.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Intermittently, there presents two occurrences of 0 stream
commits in a single HPD event. Current HDCP sequence does
not consider such scenerio, and will thus disable HDCP.
[How]
Add condition check to include stream remove and re-enable
case for HDCP enable.
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
call stack of amdgpu dsc mst pbn, slot num calculation is as below:
-compute_bpp_x16_from_target_bandwidth
-decide_dsc_target_bpp_x16
-setup_dsc_config
-dc_dsc_compute_bandwidth_range
-compute_mst_dsc_configs_for_link
-compute_mst_dsc_configs_for_state
from pbn -> dsc target bpp_x16
bpp_x16 is calulated by compute_bpp_x16_from_target_bandwidth.
Beside pixel clock and bpp, num_slices_h and bpp_increment_div
will also affect bpp_x16.
from dsc target bpp_x16 -> pbn
within dm_update_mst_vcpi_slots_for_dsc,
pbn = drm_dp_calc_pbn_mode(clock, bpp_x16, true);
drm_dp_calc_pbn_mode(int clock, int bpp, bool dsc)
{
return DIV_ROUND_UP_ULL(mul_u32_u32(clock * (bpp / 16), 64 * 1006),
8 * 54 * 1000 * 1000);
}
bpp / 16 trunc digits after decimal point. This will cause calculation
delta. drm_dp_calc_pbn_mode does not have other informations,
like num_slices_h, bpp_increment_div. therefore, it does not do revese
calcuation properly from bpp_x16 to pbn.
pbn from drm_dp_calc_pbn_mode is less than pbn from
compute_mst_dsc_configs_for_state. This cause not enough mst slot
allocated to display. display could not visually light up.
[How]
pass pbn from compute_mst_dsc_configs_for_state to
dm_update_mst_vcpi_slots_for_dsc
Cc: stable@vger.kernel.org
Reviewed-by: Scott Foster <Scott.Foster@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On Carrizo/Stoney systems we set backlight through panel_cntl, i.e.
directly via the PWM registers, if DMCU is not initialized. We
always read it back through ABM registers which leads to a
mismatch and forces atomic_commit to program the backlight
each time.
Instead make sure we use the same logic for backlight readback,
i.e. read it from panel_cntl if DMCU is not initialized.
We also need to remove some extraneous and incorrect calculations
at the end of dce_get_16_bit_backlight_from_pwm.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1666
Cc: stable@vger.kernel.org
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Assert only when FPU is not enabled.
Fixes: 0ea7ee8217 ("drm/amd/display: Add DC_FP helper to check FPU state")
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we're running a headless config with 0 links then the vblank
workqueue will be NULL - causing a NULL pointer exception during
any commit.
[How]
Guard access to the workqueue if it's NULL and don't queue or flush
work if it is.
Reported-by: Mike Lothian <mike@fireburn.co.uk>
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1700
Fixes: 58aa1c50e5 ("drm/amd/display: Use vblank control events for PSR enable/disable")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In amdgpu_dm_atomic_check, dc_validate_global_state is called. On
failure this logs a warning to the kernel journal. However warnings
shouldn't be used for atomic test-only commit failures: user-space
might be perfoming a lot of atomic test-only commits to find the
best hardware configuration.
Downgrade the log to a regular DRM atomic message. While at it, use
the new device-aware logging infrastructure.
This fixes error messages in the kernel when running gamescope [1].
[1]: https://github.com/Plagman/gamescope/issues/245
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Sequences to handle powering down these sub-IP blocks are now ready for use
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Power down VPG and AFMT blocks when not in use
[HOW]
Create afmt31 and vpg31 structs and add necessary fields to reg list
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Degamma coefficients are calculated in our degamma formula using
the regamma coefficients. We do not need to add separate degamma
coefficients.
[How]
Remove the change to add separate degamma coefficients.
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If link training is aborted, it shall be retried if sink is present.
[How]
Check hpd status to find out whether sink is present or not. If sink is
present, then link training shall be tried again with same settings.
Otherwise, link training shall be aborted.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Intermittently, there presents two occurrences of 0 stream
commits in a single HPD event. Current HDCP sequence does
not consider such scenerio, and will thus disable HDCP.
[How]
Add condition check to include stream remove and re-enable
case for HDCP enable.
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Correct degamma coefficients
* Optimize bandwidth on following fast update
* Fix multiple memory leaks reported by coverity
* Get backlight from PWM if DMCU is not initialized
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some incorrect coefficients were being used
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* PSR SMU optimizations
* MST dock fixes
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When system is in Z10 HPD interrupts cannot fire, we may miss display
configuration changes.
[How]
When Zstate is enabled, if DMUB indicate DCN has lost power, do a
complete detection periodically.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
call stack of amdgpu dsc mst pbn, slot num calculation is as below:
-compute_bpp_x16_from_target_bandwidth
-decide_dsc_target_bpp_x16
-setup_dsc_config
-dc_dsc_compute_bandwidth_range
-compute_mst_dsc_configs_for_link
-compute_mst_dsc_configs_for_state
from pbn -> dsc target bpp_x16
bpp_x16 is calulated by compute_bpp_x16_from_target_bandwidth.
Beside pixel clock and bpp, num_slices_h and bpp_increment_div
will also affect bpp_x16.
from dsc target bpp_x16 -> pbn
within dm_update_mst_vcpi_slots_for_dsc,
pbn = drm_dp_calc_pbn_mode(clock, bpp_x16, true);
drm_dp_calc_pbn_mode(int clock, int bpp, bool dsc)
{
return DIV_ROUND_UP_ULL(mul_u32_u32(clock * (bpp / 16), 64 * 1006),
8 * 54 * 1000 * 1000);
}
bpp / 16 trunc digits after decimal point. This will cause calculation
delta. drm_dp_calc_pbn_mode does not have other informations,
like num_slices_h, bpp_increment_div. therefore, it does not do revese
calcuation properly from bpp_x16 to pbn.
pbn from drm_dp_calc_pbn_mode is less than pbn from
compute_mst_dsc_configs_for_state. This cause not enough mst slot
allocated to display. display could not visually light up.
[How]
pass pbn from compute_mst_dsc_configs_for_state to
dm_update_mst_vcpi_slots_for_dsc
Cc: stable@vger.kernel.org
Reviewed-by: Scott Foster <Scott.Foster@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some scenarios like fullscreen game, major plane is scaled. Then
if a upper layer owns the cursor, cursor is invisiable in the
majority of the screen.
[How]
Instead assuming upper plane handles cursor, summing up upper
split planes on the same layer. If whole upper plane covers current
half/whole pipe plane, disable cursor.
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The current call to optimize_bandwidth never occurs because flip is
always pending from the FULL and FAST updates.
[How]
Optimize on the following flip when it's a FAST update and we know we
aren't going to be modifying the clocks again.
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans under 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enablement, causing DMUB to access an irresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off when there is any HPD status in
connected state.
Reviewed-by: Hersen Wu <hersenwu@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In YUV case, need to set the input TF to sRGB instead of BT709,
even though the input TF type is distributed. SRGB was not
being used because pixel format was not being set in the
surface update sequence.
Also, we were using the same coefficients for degamma and
regamma formula, causing the cutoff point of the linear
section of the curve to be incorrect.
[How]
Set pixel format in the surface update sequence. Add separate
coefficient arrays for regamma and degamma.
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit f5b6a20c7e.
This patch broke new settings from taking effect. Hotplug is
required for new settings to take effect.
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On Carrizo/Stoney systems we set backlight through panel_cntl, i.e.
directly via the PWM registers, if DMCU is not initialized. We
always read it back through ABM registers which leads to a
mismatch and forces atomic_commit to program the backlight
each time.
Instead make sure we use the same logic for backlight readback,
i.e. read it from panel_cntl if DMCU is not initialized.
We also need to remove some extraneous and incorrect calculations
at the end of dce_get_16_bit_backlight_from_pwm.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1666
Cc: stable@vger.kernel.org
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit "drm/amd/display: w/a for hard hang on HPD on native DP".
[How & Why]
Revert change as it does not fix the hard hang
in all cases. An alternative w/a will be submitted
separately.
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* PSR optimizations
* add support for ABM when ODM is enabled
* Z10 with PSR fixes
* Increase trace buffer
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need a check for NULL pointer access for ddc pin and aux engine.
[How]
Adding a check for ddc pin and aux engine accesses.
Reviewed-by: Jimmy Kizito <jimmy.kizito@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is an attempt to fix false warning raised by Coverity
via multiple CID's.
Addresses-Coverity-ID: 1487412 ("Free of address-of expression")
Cc: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Wesley Chalmers <wesley.chalmers@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Assuming DIG link encoders are statically mapped to links can cause
system instability due to null pointer accesses.
[How]
- Add checks for non-null link encoder pointers before trying to access
them.
- When a hardware platform uses dynamic DIG assignment (i.e. resource
function 'link_encs_assign' defined) and a link supports flexible
mapping to DIGs, use the link_enc_cfg API to access the DIG assigned to
a link or stream.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] When a connector is unplugged, dpms is forced off so that some
connector allocations are cleared off. This is done outside the commit
sequence from the userspace. This causes HUBP blank. Due to the blank
hubp, a non blocking commit which queues flip will encounter a timeout
waiting for the flip_done because prior to writing the surface flip
address, hubp was in blank.
[How] Add a marker to DM's crtc state and use this field to indicate
whether dpms was forced off during an HPD. Check for this marker before
queuing the flip.
Reviewed-by: Anson Jacob <Anson.Jacob@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When ODM is enabled, ABM is blocked on dcn31 but unblocked on dcn30.
Since the dcn31 firmware is now able to handle ABM interop with ODM, it
is no longer necessary to block ABM when ODM is enabled.
Since the dcn30 firmware does not handle ABM interop with ODM, leaving
that combination unblocked can lead to one side of the screen appearing
brighter than the other.
[How]
When ODM is enabled, unblock abm on dcn31 and block it on dcn30
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, we will try to get dm.dc_lock in handle_hpd_rx_irq() when
link lost happened, which is risky and could cause deadlock.
e.g. If we are under procedure to enable MST streams and then monitor
happens to toggle short hpd to notify link lost, then
handle_hpd_rx_irq() will get blocked due to stream enabling flow has
dc_lock. However, under MST, enabling streams involves communication
with remote sinks which need to use handle_hpd_rx_irq() to handle
sideband messages. Thus, we have deadlock here.
[How]
Target is to have handle_hpd_rx_irq() finished as soon as possilble.
Hence we can react to interrupt quickly. Besides, we should avoid to
grabe dm.dc_lock within handle_hpd_rx_irq() to avoid deadlock situation.
Firstly, revert patches which introduced to use dm.dc_lock in
handle_hpd_rx_irq():
* commit ("drm/amd/display: NULL pointer error during ")
* commit ("drm/amd/display: Only one display lights up while using MST")
* commit ("drm/amd/display: take dc_lock in short pulse handler only")
Instead, create work to handle irq events which needs dm.dc_lock.
Besides:
* Create struct hpd_rx_irq_offload_work_queue for each link to handle
its short hpd events
* Avoid to handle link lost/ automated test if the link is disconnected
* Defer dc_lock needed works in dc_link_handle_hpd_rx_irq(). This
function should just handle simple stuff for us (e.g. DPCD R/W).
However, deferred works should still be handled by the order that
dc_link_handle_hpd_rx_irq() used to be.
* Change function name dm_handle_hpd_rx_irq() to
dm_handle_mst_sideband_msg() to be more specific
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Due to some code flow constraints, we need to defer dc_lock needed works
from dc_link_handle_hpd_rx_irq(). Thus, do following changes:
* Change allow_hpd_rx_irq() from static to public
* Change handle_automated_test() from static to public
* Extract link lost handling flow out from dc_link_handle_hpd_rx_irq()
and put those into a new function dc_link_dp_handle_link_loss()
* Add one option parameter to decide whether defer works within
dc_link_handle_hpd_rx_irq()
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
According to DP specs dfp cap ext validation is only for branch
device withou 128b/132b channel coding support and
downstream of the branch device doesn't have compression.
Therefore we are adding conditions to only do dfp cap
extension validation for branch devcie supporting 8b/10b
channel coding only and it has no DSC passthrough capability.
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before get dsc bw range is used to compute DSC bw range
based on the given fixed bpp min/max input.
The new change will merge any specs, signal, timing specific
bpp range decision into this function. So the function needs to make
a decision with all aspects considered.
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During DQE's promotion test, system hang issue is found on linux
system;
[How]
1. Add NULL pointor check for the link in the sequence trace
function;
2. Get the right link for the stream encoder before blank DP
stream;
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit "Revert "Add DPCD writes at key points" ".
The following patch will fix the system hang issue.
v2: squash in indentation warning fix
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DM needs to know how much overhead is added to DSC as result
of AMD internal DSC limitation.
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Assert only when FPU is not enabled.
Fixes: 0ea7ee8217 ("drm/amd/display: Add DC_FP helper to check FPU state")
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we're running a headless config with 0 links then the vblank
workqueue will be NULL - causing a NULL pointer exception during
any commit.
[How]
Guard access to the workqueue if it's NULL and don't queue or flush
work if it is.
Reported-by: Mike Lothian <mike@fireburn.co.uk>
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1700
Fixes: 58aa1c50e5 ("drm/amd/display: Use vblank control events for PSR enable/disable")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ttm:
- Fix ttm_bo_move_memcpy() when ttm_resource is subclassed.
- Fix ttm deadlock if target BO isn't idle
- ttm build fix
- ttm docs fix
dma-buf:
- config option fixes
fbdev:
- limit resolutions to avoid int overflow
i915:
- stddef change.
amdgpu:
- Misc cleanups, typo fixes
- EEPROM fix
- Add some new PCI IDs
- Scatter/Gather display support for Yellow Carp
- PCIe DPM fix for RKL platforms
- RAS fix
amdkfd:
- SVM fix
vc4:
- static function fix
mgag200:
- fix uninit var
panfrost:
- lock_region fixes
- Make some dma-buf config options depend on DMA_SHARED_BUFFER.
- Handle multiplication overflow of fbdev xres/yres in the core.
-----BEGIN PGP SIGNATURE-----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=R62Q
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2021-09-10' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Just an initial bunch of fixes for the merge window, amdgpu is most of
them with a few ttm fixes and an fbdev avoid multiply overflow fix.
core:
- Make some dma-buf config options depend on DMA_SHARED_BUFFER
- Handle multiplication overflow of fbdev xres/yres in the core
ttm:
- Fix ttm_bo_move_memcpy() when ttm_resource is subclassed
- Fix ttm deadlock if target BO isn't idle
- ttm build fix
- ttm docs fix
dma-buf:
- config option fixes
fbdev:
- limit resolutions to avoid int overflow
i915:
- stddef change.
amdgpu:
- Misc cleanups, typo fixes
- EEPROM fix
- Add some new PCI IDs
- Scatter/Gather display support for Yellow Carp
- PCIe DPM fix for RKL platforms
- RAS fix
amdkfd:
- SVM fix
vc4:
- static function fix
mgag200:
- fix uninit var
panfrost:
- lock_region fixes"
* tag 'drm-next-2021-09-10' of git://anongit.freedesktop.org/drm/drm: (36 commits)
drm/ttm: Fix a deadlock if the target BO is not idle during swap
fbmem: don't allow too huge resolutions
dma-buf: DMABUF_SYSFS_STATS should depend on DMA_SHARED_BUFFER
dma-buf: DMABUF_DEBUG should depend on DMA_SHARED_BUFFER
drm/i915: use linux/stddef.h due to "isystem: trim/fixup stdarg.h and other headers"
dma-buf: DMABUF_MOVE_NOTIFY should depend on DMA_SHARED_BUFFER
drm/amdkfd: drop process ref count when xnack disable
drm/amdgpu: enable more pm sysfs under SRIOV 1-VF mode
drm/amdgpu: fix fdinfo race with process exit
drm/amdgpu: Fix a deadlock if previous GEM object allocation fails
drm/amdgpu: stop scheduler when calling hw_fini (v2)
drm/amdgpu: Clear RAS interrupt status on aldebaran
drm/amd/display: Initialize lt_settings on instantiation
drm/amd/display: cleanup idents after a revert
drm/amd/display: Fix memory leak reported by coverity
drm/ttm: Fix ttm_bo_move_memcpy() for subclassed struct ttm_resource
drm/amdgpu/swsmu: fix spelling mistake "minimun" -> "minimum"
drm/amdgpu: Disable PCIE_DPM on Intel RKL Platform
drm/amdgpu: show both cmd id and name when psp cmd failed
drm/amd/display: setup system context for APUs
...
This symbols is not used outside of dc_link_dp.c, so marks it static.
Fix the following sparse warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:1766:16:
warning: symbol 'configure_lttpr_mode_non_transparent' was not declared.
Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:1755:16:
warning: symbol 'configure_lttpr_mode_transparent' was not declared.
Should it be static?
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In amdgpu_dm_atomic_check, dc_validate_global_state is called. On
failure this logs a warning to the kernel journal. However warnings
shouldn't be used for atomic test-only commit failures: user-space
might be perfoming a lot of atomic test-only commits to find the
best hardware configuration.
Downgrade the log to a regular DRM atomic message. While at it, use
the new device-aware logging infrastructure.
This fixes error messages in the kernel when running gamescope [1].
[1]: https://github.com/Plagman/gamescope/issues/245
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add -s option (strict mode) to merge_config.sh to make it fail when
any symbol is redefined.
- Show a warning if a different compiler is used for building external
modules.
- Infer --target from ARCH for CC=clang to let you cross-compile the
kernel without CROSS_COMPILE.
- Make the integrated assembler default (LLVM_IAS=1) for CC=clang.
- Add <linux/stdarg.h> to the kernel source instead of borrowing
<stdarg.h> from the compiler.
- Add Nick Desaulniers as a Kbuild reviewer.
- Drop stale cc-option tests.
- Fix the combination of CONFIG_TRIM_UNUSED_KSYMS and CONFIG_LTO_CLANG
to handle symbols in inline assembly.
- Show a warning if 'FORCE' is missing for if_changed rules.
- Various cleanups
-----BEGIN PGP SIGNATURE-----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=lw3M
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add -s option (strict mode) to merge_config.sh to make it fail when
any symbol is redefined.
- Show a warning if a different compiler is used for building external
modules.
- Infer --target from ARCH for CC=clang to let you cross-compile the
kernel without CROSS_COMPILE.
- Make the integrated assembler default (LLVM_IAS=1) for CC=clang.
- Add <linux/stdarg.h> to the kernel source instead of borrowing
<stdarg.h> from the compiler.
- Add Nick Desaulniers as a Kbuild reviewer.
- Drop stale cc-option tests.
- Fix the combination of CONFIG_TRIM_UNUSED_KSYMS and CONFIG_LTO_CLANG
to handle symbols in inline assembly.
- Show a warning if 'FORCE' is missing for if_changed rules.
- Various cleanups
* tag 'kbuild-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kbuild: redo fake deps at include/ksym/*.h
kbuild: clean up objtool_args slightly
modpost: get the *.mod file path more simply
checkkconfigsymbols.py: Fix the '--ignore' option
kbuild: merge vmlinux_link() between ARCH=um and other architectures
kbuild: do not remove 'linux' link in scripts/link-vmlinux.sh
kbuild: merge vmlinux_link() between the ordinary link and Clang LTO
kbuild: remove stale *.symversions
kbuild: remove unused quiet_cmd_update_lto_symversions
gen_compile_commands: extract compiler command from a series of commands
x86: remove cc-option-yn test for -mtune=
arc: replace cc-option-yn uses with cc-option
s390: replace cc-option-yn uses with cc-option
ia64: move core-y in arch/ia64/Makefile to arch/ia64/Kbuild
sparc: move the install rule to arch/sparc/Makefile
security: remove unneeded subdir-$(CONFIG_...)
kbuild: sh: remove unused install script
kbuild: Fix 'no symbols' warning when CONFIG_TRIM_UNUSD_KSYMS=y
kbuild: Switch to 'f' variants of integrated assembler flag
kbuild: Shuffle blank line to improve comment meaning
...
Pointer sink is being inintialized with a value that is never read,
it is later being re-assigned a new value. Remove the redundant
initialization.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a DC_LOG_WARNING message. Fix it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- FW promotion 0.0.80
- Add missing ABM register offsets
- Fix in swizzle mode mapping
- Emulated sink support for freesync
- Improvoments in max target bpp
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add volatile to avoid incomplete flushing of data in rb
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swizzle mode enum for DC_SW_VAR_R_X was existing,
but not mapped correctly.
[How]
Update mapping and conversion for DC_SW_VAR_R_X.
Reviewed-by: XiangBing Foo <XiangBing.Foo@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Cc: stable@vger.kernel.org
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When forced modes are used during certain IGT tests,
without a real connector, dc_sink would be null when
standard modes are added by the driver. Calling the
function to update freesync capabilities at this
point will result in an error being printed
[How]
Use emulated sink when available. If both the normal
and emulated sink are not available, set all freesync
parameters to 0.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some monitors exhibit corruption at 16bpp DSC.
[How]
- Add helpers for patching edid caps.
- Use it for limiting DSC target bitrate to 15bpp for known monitors
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Cc: stable@vger.kernel.org
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Max target bpp override is an option for working around
DSC issues. It is supported on DC level, but was not
used in DM.
[How]
Use actual option value instead of 0.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Clocks don't get recalculated in 0 stream/0 pipe configs,
blocking S0i3 if dcfclk gets high enough
[HOW]
Create DCN31 copy of DCN30 bandwidth validation func which
doesn't entirely skip validation in 0 pipe scenarios
Override dcfclk to vlevel 0/min value during validation if pipe
count is 0
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To add support for HPD interrupt handling from DMUB.
HPD interrupt could be triggered from outbox1 from DMUB
[HOW]
1) Use queue_work to handle hpd task from outbox1
2) Add handle_hpd_irq_helper to share interrupt handling code
between legacy and DMUB HPD from outbox1
3) Added DMUB HPD handling in dmub_srv_stat_get_notification().
HPD handling callback function and wake up the DMUB thread.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Jude Shih <shenshih@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some ABM registers don't exist on DCN 3.01, so are
missing from its register offset list. However,
this list was copied to later versions of DCN that
do have these registers. As a result, they're
inaccessible from the driver on those DCN versions
even though they exist.
[How]
Add the missing ABM register offsets to DCN 3.02+
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Retrieve 128/132b link cap.
2. 128/132b link training and payload allocation.
3. UHBR10 link rate support.
[squash in warning fixes - Alex]
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
lt_settings' pointers remain uninitialized but nonzero if display fails
to light up with no DPCD/EDID info populated, leading to a hang on access
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The change has caused high idle memory clock speed and power
consumption at some resolutions and frame rates for Navi10
[HOW]
Reverted change "drm/amd/display: Fixed Intermittent blue
screen on OLED panel"
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Angus Wang <angus.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Free memory allocated if any of the previous allocations failed.
>>> CID 1487129: Resource leaks (RESOURCE_LEAK)
>>> Variable "vpg" going out of scope leaks the storage it points to.
Addresses-Coverity-ID: 1487129: ("Resource leaks")
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Scatter/gather is APU feature starting from carrizo.
adev->apu_flags is not used for all APUs.
adev->flags & AMD_IS_APU can be used for all APUs.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
./drivers/gpu/drm/amd/display/dc/dcn31/dcn31_panel_cntl.c:112:9-10:WARNING:
return of 0/1 in function 'dcn31_is_panel_backlight_on'
with return type bool
./drivers/gpu/drm/amd/display/dc/dcn31/dcn31_panel_cntl.c:122:9-10:WARNING:
return of 0/1 in function 'dcn31_is_panel_powered_on'
with return type bool
Return statements in functions returning bool should use true/false
instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Jing Yangyang <jing.yangyang@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This is a global parameter, not a per pipe parameter and it's useful
for experimenting with the prefetch schedule to be adjustable from
the SOC bb.
[How]
Add a parameter to the SOC bb, default is the existing policy for
all DCN. Fill it in when filling SOC bb parameters.
Revert the policy to use MinDCFClk at the same time since that's not
going to give us P-State in most cases on the spreadsheet.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1403
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DML is initialized again unnecessarily after its done conditionally.
Remove the duplicate initialization
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1403
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The DCN3 SoC parameter num_states was calculated but not saved into the
object.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1403
Cc: stable@vger.kernel.org
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recent HDMI2.0 HF1-1 V-Swing testing showed that logging deep color
status helps in validation of testcase.
[How]
Add logging based on various color depths and pixel encoding
formats.
Signed-off-by: Praful Swarnakar <Praful.Swarnakar@amd.com>
Reviewed-by: Hersen Wu <hersenwu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A cleaner solution, only done once on boot.
[How]
Remove previous workaround and configure an extra
vmid one time on boot
Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ship minimal stdarg.h (1 type, 4 macros) as <linux/stdarg.h>.
stdarg.h is the only userspace header commonly used in the kernel.
GPL 2 version of <stdarg.h> can be extracted from
http://archive.debian.org/debian/pool/main/g/gcc-4.2/gcc-4.2_4.2.4.orig.tar.gz
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Delete/fixup few includes in anticipation of global -isystem compile
option removal.
Note: crypto/aegis128-neon-inner.c keeps <stddef.h> due to redefinition
of uintptr_t error (one definition comes from <stddef.h>, another from
<linux/types.h>).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dcn301_calculate_wm_and_dl() causes flickering when external monitor is
connected.
This issue has been fixed before by commit 0e4c0ae59d
("drm/amdgpu/display: drop dcn301_calculate_wm_and_dl for now"), however
part of the fix was gone after commit 2cbcb78c9e ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next").
[how]
Use dcn30_calculate_wm_and_dlg() instead as in the original fix.
Fixes: 2cbcb78c9e ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Oliver Logush <oliver.logush@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Ensure DCN save init registers after VM setup
- Fix multi-display support for idle opt workqueue
- Use vblank control events for PSR enable/disable
- Create default dc_sink when fail reading EDID under MST
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Compilation of the workqueue fails if not building with the DCN config
option set.
[How]
Guard calls to the flush with the DCN config option to fix the build.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM initializes VM context after DMCUB initialization.
This results in loss of DCN_VM_CONTEXT registers after z10.
[How]
Notify DMCUB when VM setup is complete, and have DMCUB
save init registers.
v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR can disable the HUBP along with the OTG when PSR is active.
We'll hit a pageflip timeout when the OTG is disable because we're no
longer updating the CRTC vblank counter and the pflip high IRQ will
not fire on the flip.
In order to flip the page flip timeout occur we should modify the
enter/exit conditions to match DRM requirements.
[How]
Use our deferred handlers for DRM vblank control to notify DMCU(B)
when it can enable or disable PSR based on whether vblank is disabled or
enabled respectively.
We'll need to pass along the stream with the notification now because
we want to access the CRTC state while the CRTC is locked to get the
stream state prior to the commit.
Retain a reference to the stream so it remains safe to continue to
access and release that reference once we're done with it.
Enable/disable logic follows what we were previously doing in
update_planes.
The workqueue has to be flushed before programming streams or planes
to ensure that we exit out of idle optimizations and PSR before
these events occur if necessary.
To keep the skip count logic the same to avoid FBCON PSR enablement
requires copying the allow condition onto the DM IRQ parameters - a
field that we can actually access from the worker.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The current implementation for idle optimization support only has a
single work item that gets reshuffled into the system workqueue
whenever we receive an enable or disable event.
We can have mismatched events if the work hasn't been processed or if
we're getting control events from multiple displays at once.
This fixes this issue and also makes the implementation usable for
PSR control - which will be addressed in another patch.
[How]
We need to be able to flush remaining work out on demand for driver stop
and psr disable so create a driver specific workqueue instead of using
the system one. The workqueue will be single threaded to guarantee the
ordering of enable/disable events.
Refactor the queue to allocate the control work and deallocate it
after processing it.
Pass the acrtc directly to make it easier to handle psr enable/disable
in a later patch.
Rename things to indicate that it's not just MALL specific.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While reading remote EDID via Startech 1-to-4 hub, occasionally we
won't get response in time and won't light up corresponding monitor.
Ideally, we can still add generic modes for userspace to choose to try
to light up the monitor and which is done in
drm_helper_probe_single_connector_modes(). So the main problem here is
that we fail .mode_valid since we don't create remote dc_sink for this
case.
[How]
Also add default dc_sink if we can't get the EDID.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable dc->clk_mgr is checked in:
if (dc->clk_mgr && dc->clk_mgr->funcs->get_clock)
This indicates dc->clk_mgr can be NULL.
However, it is dereferenced in:
if (!dc->clk_mgr->funcs->get_clock)
To fix this null-pointer dereference, check dc->clk_mgr and the function
pointer dc->clk_mgr->funcs->get_clock earlier, and return if one of them
is NULL.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Building with W=1 complains about an empty 'else' statement, so use the
usual do-nothing-while-0 loop to quieten this warning.
../drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:113:53: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
113 | *state, retry_count);
Fixes: b30eda8d41 ("drm/amd/display: Add ETW log to dmub_psr_get_state")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we're backdoor loading the DMCUB performs more work than just
the PHY reset so we can end up resetting before the cleanup has fully
finished.
[How]
Increase timeout, add udelay between spins to guarantee a minimum.
Reviewed-by: Roy Chan <roy.chan@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Otherwise we can end up processing whatever was left in the register
if the DMCUB was previously reset.
If DMCUB gets force reset too early from another client then we might
not have even acked the disable yet - causing DMCUB instantly shutdown
if the command was 10020000.
[How]
Move the GPINT clear outside of the reset loop and do it unconditionally
after the DMCUB has been properly reset.
Reviewed-by: Roy Chan <roy.chan@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fix memory allocation in dm IRQ context to use GFP_ATOMIC
- Increase timeout threshold for DMCUB reset
- Clear GPINT after DMCUB has reset
- Add AUX I2C tracing
- Fix code commenting style
- Some refactoring
- Remove invalid assert for ODM + MPC case
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DM needs to be notified when hdcp module has completed
authentication attempt.
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Developers can find it useful if the driver can produce
AUX traces without special equipment.
[How]
Add AUX tracing.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
the programming sequeune was for old asic.
the correct programming sequeunce should be similar to the one
used in mpc. the fix is copied from the mpc programming sequeunce.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the plane has been removed, the writeback disablement logic
doesn't run
[How]
fix the logic order
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable eng_id is being initialized with a value that is never
read, it is being re-assigned on the next statment. The assignment
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With kernel module parameter "freesync_video" is enabled, if the mode
is changed to preferred mode(the mode with highest rate), then Freesync
fails because the preferred mode is treated as one of freesync video
mode, and then be configurated as freesync video mode(fixed refresh
rate).
[How]
Skip freesync fixed rate configurating when modeset to preferred mode.
Signed-off-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMUB firmware info is printed before it gets initialized.
Correct this order to ensure true value is conveyed.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To fully isolate FPU operations in a single place, we must avoid
situations where compilers spill FP values to registers due to FP enable
in a specific C file. Note that even if we isolate all FPU functions in
a single file and call its interface from other files, the compiler
might enable the use of FPU before we call DC_FP_START. Nevertheless, it
is the programmer's responsibility to invoke DC_FP_START/END in the
correct place. To highlight situations where developers forgot to use
the FP protection before calling the DC FPU interface functions, we
introduce a helper that checks if the function is invoked under FP
protection. If not, it will trigger a kernel warning.
Changes cince V3:
- Rebase
Changes cince V2 (Christian):
- Do not use this_cpu_* between get/put_cpu_ptr().
- In the kernel documentation, better describe restrictions.
- Make dc_assert_fp_enabled trigger the ASSERT message.
Changes since V1:
- Remove fp_enable variables
- Rename dc_is_fp_enabled to dc_assert_fp_enabled
- Replace wrong variable type
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Anson Jacob <Anson.Jacob@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Jun Lei <jun.lei@amd.com>
Cc: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Cc: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC invokes DC_FPU_START/END in multiple parts of the code; this can
create a situation where we invoke this FPU operation in a nested way or
exit too early. For avoiding this situation, this commit adds a
mechanism where dc_fpu_begin/end manages the access to
kernel_fpu_begin/end.
Change since V3:
- Rebase
Change since V2:
- Christian: Do not use this_cpu_* between get/put_cpu_ptr().
Change since V1:
- Use a better variable names
- Use get_cpu_ptr and put_cpu_ptr to better balance preemption enable
and disable
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Anson Jacob <Anson.Jacob@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Jun Lei <jun.lei@amd.com>
Cc: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Cc: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC invokes DC_FPU_START/END in multiple parts of the code; this can
create a situation where we invoke this FPU operation in a nested way or
exit too early. For avoiding this situation, this commit adds a
mechanism where dc_fpu_begin/end manages the access to
kernel_fpu_begin/end.
Change since V3:
- Christian: Move PPC64 code to dc_fpu_begin/end.
Change since V2:
- Christian: Do not use this_cpu_* between get/put_cpu_ptr().
Change since V1:
- Use a better variable names
- Use get_cpu_ptr and put_cpu_ptr to better balance preemption enable
and disable
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Anson Jacob <Anson.Jacob@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Jun Lei <jun.lei@amd.com>
Cc: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Cc: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The display core files rely on FPU, which requires to be compiled with
special flags. Ideally, we don't want these FPU operations spread around
the DC code; nevertheless, it happens in the current source. This commit
introduces a new directory inside DML for centralizing shared DCN
functions that require FPU and have been used outside DML. For
illustrating this process of transferring FPU functions to the DML
folder, this commit moves one of the functions
dcn20_populate_dml_writeback_from_context) that require FPU access to a
single shared file. Notice that this is the first part of the work, and
it does not fix the FPU issue yet; we still need other patches for
achieving the complete FPU isolation.
Changes since V3:
- Jun: Instead of creating a new directory to keep the FPU code, let's
make the DML folder the only part that requires FPU access. Drop
fpu_operation folder.
- Christian: Fix function code style.
Changes since V2:
- Christian: Remove unnecessary wrapper.
- lkp: Add missing prototype.
- Only compile the FPU operations if the DCN option is enabled.
Change since V1:
- Update documentation and rebase.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Anson Jacob <Anson.Jacob@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Jun Lei <jun.lei@amd.com>
Cc: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Cc: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans over 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enable, causing DMUB to access an unresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off on native DP.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We do not currently support ODM plus MPO on only one side of the
screen. This unsupported case causes validation calculations to
divide by zero due to invalid viewport values.
[How]
Add stopgap for the validation of ODM plus MPO on one side of
screen case.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jaehyun Chung <jaehyum.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] On S4 resume we also need to fix detection of when to reload DMCUB
firmware because we're currently using the VBIOS version which isn't
compatible with the driver version.
[How] Update the hardware init check for DCN31 since it's the ASIC that
has this issue.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jude Shih <jude.shih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Display Manager initializes array of vblank workqueues, but only 1 is used.
[How]
Use single instance init instead of array.
Reviewed-by: Qingqing Zhou <Qingqing.Zhuo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Hardware team suggested to use SRExitTime= 35.5us as w/a to prevent
underflow in certain modes.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
In DCN2x, HW doesn't automatically divide MASTER_UPDATE_LOCK_DB_X
by the number of pipes ODM Combined.
How:
Set MASTER_UPDATE_LOCK_DB_X to the value that is adjusted by the
number of pipes ODM Combined.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
For DCN31 onward, LTTPR is to be enabled and set to Transparent by
VBIOS. Driver is to assume that VBIOS has done this without needing to
check the VBIOS interop bit.
[HOW]
Add LTTPR enable and interop VBIOS bits into dc->caps, and force-set the
interop bit to true for DCN31+.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMUB firmware info is printed before it gets initialized.
Correct this order to ensure true value is conveyed.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans over 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enable, causing DMUB to access an unresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off on native DP.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
