The BIOS or boot loader will generally create an initial display
configuration for us that includes some set of active pipes and
displays. This routine tries to figure out which pipes and connectors
are active and stuffs them into the crtcs and modes array given to us by
the drm_fb_helper code.
The overall sequence is:
intel_fbdev_init - from driver load
intel_fbdev_init_bios - initialize the intel_fbdev using BIOS data
drm_fb_helper_init - build fb helper structs
drm_fb_helper_single_add_all_connectors - more fb helper structs
intel_fbdev_initial_config - apply the config
drm_fb_helper_initial_config - call ->probe then register_framebuffer()
drm_setup_crtcs - build crtc config for fbdev
intel_fb_initial_config - find active connectors etc
drm_fb_helper_single_fb_probe - set up fbdev
intelfb_create - re-use or alloc fb, build out fbdev structs
v2: use BIOS connector config unconditionally if possible (Daniel)
check for crtc cloning and reject (Daniel)
fix up comments (Daniel)
v3: use command line args and preferred modes first (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Re-add the WARN_ON for a missing encoder crtc - the state
sanitizer should take care of this. And spell-ocd the comments.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to reuse this in the fbdev initial config code independently
from any fastboot hacks. So allow a bit more flexibility.
v2: Forgot to git add ...
v3: make non-static (Jesse)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to do this early on before we try to fetch the plane config,
which depends on some of the pipe config state.
Note that the important part is that we do this before we initialize
gem, since otherwise we can't properly pre-reserve the stolen memory
for framebuffers inherited from the bios.
v2: split back out from get_plane_config change (Daniel)
update for recent locking & reset changes (Jesse)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Explain a bit more why we need to move this.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... and QUIRK_PIPEA_FORCE is not present.
I initially thought that case was impossible and just added a WARN on
it, but then I was told this case is possible due to
QUIRK_PIPEA_FORCE. So let's add a WARN that serves two purposes:
- tell us in case we have done something wrong;
- document the only case where we expect this.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a nice comment explaining why we shouldn't wait for a vblank on
all cases, wait based on the HW gen, and add a comment saying we
should probably skip that wait on some of the previous HW gens.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we pass struct intel_crtc as an argument, we can check for
DSI inside the function, removing one more of those confusing boolean
arguments.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we pass struct intel_crtc as an argument, there's no need for
it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to remove those 3 boolean arguments. This is the first step.
The "pipe" passed as the argument is always intel_crtc->pipe.
Also adjust the function documentation.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When I forked haswell_crtc_enable I copied all the code from
ironlake_crtc_enable. The last piece of the function contains a big
comment with a call to intel_wait_for_vblank. After this fork, we
rearranged the Haswell code so that it enables the planes as the very
last step of the modeset sequence, so we're sure that we call
intel_enable_primary_plane after the pipe is really running, so the
vblank waiting functions work as expected. I really believe this is
what fixes the problem described by the big comment, so let's give it
a try and get rid of that intel_wait_for_vblank, saving around 16ms
per modeset (and init/resume). We can always revert if needed :)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because on Haswell, the pipe is never running at this point, so we hit
the 50ms timeout waiting for nothing. We already have two other places
where we wait for vblanks on haswell_crtc_enable, so we're safe.
This gets us rid of one instance of "vblank wait timed out" for each
mode set, which means driver init and resume are also 50ms faster.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Depending on the HW gen and the connector type, the pipe won't start
running right after we call intel_enable_pipe, so that
intel_wait_for_vblank call we currently have will just sit there for
the full 50ms timeout. So this patch adds an argument that will allow
us to avoid the vblank wait in case we want. Currently all the callers
still request for the vblank wait, so the behavior should still be the
same.
We also added a POSTING_READ on the register: previously
intel_wait_for_vblank was acting as a POSTING_READ, but now if
wait_for_vblank is false we'll stkip it, so we need an explicit
POSTING_READ.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For use by get_plane_config.
v2: cleanup tile_height bits (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Jesse's patch to switch the fbdev framebuffer from an embedded
struct to a pointer the kfree in case of an error was missed. Fix this
up by using our own internal fb allocation helper directly instead of
reinventing that wheel.
We need a to_intel_framebuffer cast unfortunately since all the other
callers of _create still look better whith using a drm_framebuffer as
return pointer.
v2: Add an unlocked __intel_framebuffer_create function since our
dev->struct_mutex locking is too much a mess. With ppgtt we even need
it to take a look at the global gtt offset of pinned objects, since
the vma list might chance from underneath us. At least with the
current global gtt lookup functions. Reported by Mika.
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that it's a normally kmalloce buffer we can use the usual cleanup
paths. The upside here is that if we get the refcounting wrong will be
able to catch it, since the drm core will complain about leftover
framebuffers and kref about underflows.
v2: Kill intel_framebuffer_fini - no longer needed now that we
refcount all fbs properly and only confusing.
v3: We actually still need to call unregister_private to remove the fb
from the idr and drop the idr reference - the final unref doesn't do
that. So much for remembering my own fb liftime rules. Reported by
Imre Deak.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Touching the VGA registers risks a hard machine hang, at least on this
ivb machine after removing a conflicting efifb. This is more than likely
related to the discovery that VGA IO decode on the more recent PCH
platforms is terminally broken.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has very little effect other than log the errors in case of failure,
and we then hope for the best.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allocate this struct instead, so we can re-use another allocated
elsewhere if needed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: WARN_ON if there's no backing storage attached to an fb,
that's a bug.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We had 2 set of defines for the same register, so make it one.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And rename it to num_sprites as this value doesn't count the primary
plane.
This limit lives with num_pipes really, and now that dev_priv->info is
writable we can put it there instead.
While at it, introduce a intel_device_info_runtime_init() where we'll be
able to gather the device info fields at run-time.
v2: rename num_plane to num_sprites (Ville Syrjälä)
v3: rebase on top of latest drm-nightly
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (for v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (for v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we make sure that all the dev_priv->info usages are wrapped by
INTEL_INFO(), we can easily modify the ->info field to be structure and
not a pointer while keeping the const protection in the INTEL_INFO()
macro.
v2: Rebased onto latest drm-nightly
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec the entire MI_DISPLAY_FLIP packet must be contained
in a single cacheline. Make sure that happens.
v2: Use intel_ring_begin_cacheline_safe()
v3: Use intel_ring_cacheline_align() (Chris)
Cc: Bjoern C <lkml@call-home.ch>
Cc: Alexandru DAMIAN <alexandru.damian@intel.com>
Cc: Enrico Tagliavini <enrico.tagliavini@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74053
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next - I need to backmerge drm-intel-fixes patches
touching the error capture code to be able to merge Ben's cleanup
patches.
Conflicts:
drivers/gpu/drm/i915/i915_gpu_error.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These patches fix some issues caused by the DRM panel support from the
previous pull request and add two more panels (for the Toshiba AC100 as
well as the Seaboard and Ventana).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=NfNj
-----END PGP SIGNATURE-----
Merge tag 'drm/for-3.14-rc1-20140123' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.14-rc1 (update)
These patches fix some issues caused by the DRM panel support from the
previous pull request and add two more panels (for the Toshiba AC100 as
well as the Seaboard and Ventana).
* tag 'drm/for-3.14-rc1-20140123' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Obtain head number from DT
drm/panel: update EDID BLOB in panel_simple_get_modes()
gpu: host1x: Remove unnecessary include
drm/tegra: Use proper data type
drm/tegra: Clarify how panel modes override others
drm/tegra: Fix possible CRTC mask for RGB outputs
drm/i915: Use drm_encoder_crtc_ok()
drm: Move drm_encoder_crtc_ok() to core
drm: provide a helper for the encoder possible_crtcs mask
drm/tegra: Don't check resource with devm_ioremap_resource()
drm/panel: Add support for Chunghwa CLAA101WA01A panel
drm/panel: Add support for Samsung LTN101NT05 panel
With 20+ module parameters, I think referring to them via a struct
improves clarity over just having a bunch of globals. While at it, move
the parameter initialization and definitions into a new file
i915_params.c to reduce clutter in i915_drv.c.
Apart from the ill-named i915_enable_rc6, i915_enable_fbc and
i915_enable_ppgtt parameters, for which we lose the "i915_" prefix
internally, the module parameters now look the same both on the kernel
command line and in code. For example, "i915.modeset".
The downsides of the change are losing static on a couple of variables
and not having the initialization and module_param_named() right next to
each other. On the other hand, all module parameters are now defined in
one place at i915_params.c. Plus you can do this to find all module
parameter references:
$ git grep "i915\." -- drivers/gpu/drm/i915
v2:
- move the definitions into a new file
- s/i915_params/i915/
- make i915_try_reset i915.reset, for consistency
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we print all pipe underruns on GMCH platforms. Hook up the
same logic we use on PCH platforms where we disable the underrun
reporting after the first underrun.
Underruns don't actually generate interrupts themselves on GMCH
platforms, we just can detect them whenever we service other
interrupts. So we don't have any enable bits to worry about. We just
need to remember to clear the underrun status when enabling underrun
reporting.
Note that the underrun handling needs to be moved to the non-locked
pipe_stats[] loop in the interrupt handlers to avoid having to rework
the locking in intel_set_cpu_fifo_underrun_reporting().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have DDI support, we can check these all the time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit ee1452d745
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Sep 20 15:05:30 2013 +0300
drm/i915: assume all GM45 Acer laptops use inverted backlight PWM
failed and was later reverted in
commit be505f6439
Author: Alexander van Heukelum <heukelum@fastmail.fm>
Date: Sat Dec 28 21:00:39 2013 +0100
Revert "drm/i915: assume all GM45 Acer laptops use inverted backlight PWM"
fix the individual broken machine instead.
Note to backporters:
http://patchwork.freedesktop.org/patch/17837/
is the patch you want for 3.13 and older.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54171
Reference: http://mid.gmane.org/DUB115-W7628C7C710EA51AA110CD4A5000@phx.gbl
CC: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Patch mangling for 3.14 plus adding the link to the original
for 3.13.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we're doing the reset handling a bit late, and we're doing
it both in the driver load code and on resume. This makes it unusable
for e.g. resetting the panel power sequence state like Paulo wants to.
Instead of adding yet another single-use callback shuffle things
around:
- Output handling code is responsible to reset/init all state on its
own at driver load time.
- We call the reset functions much earlier, before we start using any
of the modeset code.
Compared to Paulo's new ->resume callback the only difference in
placement is that ->reset is still called without dev->struct_mutex
held. Which is imo a feature.
v2: Rebase on top of the now merge dinq.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I forgot to set new_config and new_enabled appropriately in the load
detect code. Fix it up.
v2: Handle the other error path in intel_get_load_detect_pipe() too (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
crtc->new_config is only relevant for pipes that are going to be active
post-modeset. Set the pointer to NULL for all pipes that are going to
be disabled. This is done to help catch bugs where some piece of code
would go looking at crtc->new_config even if the data there is stale.
v2: Clear new_config in disable_crtc_nofb() too (Imre)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the first modeset operation fails, we will attempt to restore the
previous configuration that we read out from the hardware. But as we
don't yet reconstruct the framebuffer information, we end up calling
the modeset code with an enabled crtc but with fb==NULL. This will
lead to an oops within the modeset code.
Check for NULL fb when restoring the configuration, and instead of
oopsing simply disable the pipe.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV we need to compute the new cdclk before we've updated the current
state. The code achieved that in a somewhat complex way. Now that we
have new_enabled and new_config, we can simplify the code quite a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new_config pointer to intel_crtc which will point to the new pipe
config for said crtc while intel_crtc.config will still contain the old
config during first parts of the modeset operation. This is a step
towards having the entire new state available during the compute phase,
so that we can make accurate decisions about global resource usage.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add 'new_enabled' to intel_crtc and precompute it alongside new_encoder
and new_crtc. This will allow making decisions about shared resources
that are affected by the set of active pipes, before we've clobbered
anything for real.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 446f254566.
I've left the masking in the pageflip code since that seems to be some
useful piece of preemptive robustness.
Iirc I've merged this patch under the assumption that the BIOS leaves
some random gunk in the lower bits and gets unhappy if we trample on
them. We have quite a few case like this, so this made sense.
Now I've just learned that there's actual hardware features bits in
the low 12 bits, and the kernel needs to preserve them to allow a
userspace blob to do its job. Given Dave Airlie's clear stance on
userspace blob drivers I've quickly chatted with him and he doesn't
seem too happy. So let's revert this.
If there are indeed bits that we must preserve in this range then we
can ressurrect this patch, but with proper documentation for those
bits supplied. And we probably also need to think a bit about
interactions with our driver.
Cc: Armin Reese <armin.c.reese@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@linux.ie>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On older generations (gen2, gen3) the GPU requires fences for many
operations, such as blits. The display hardware also requires fences for
scanouts and this leads to a situation where an arbitrary number of
fences may be pinned by old scanouts following a pageflip but before we
have executed the unpin workqueue. This is unpredictable by userspace
and leads to random EDEADLK when submitting an otherwise benign
execbuffer. However, we can detect when we have an outstanding flip and
so cause userspace to wait upon their completion before finally
declaring that the system is starved of fences. This is really no worse
than forcing the GPU to stall waiting for older execbuffer to retire and
release their fences before we can reallocate them for the next
execbuffer.
v2: move the test for a pending fb unpin to a common routine for
later reuse during eviction
Reported-and-tested-by: dimon@gmx.net
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73696
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Update the pixel/line/frame duration information when we switch to the
new pipe config. This will keep the timestamping constants in better
sync with the real hardware state.
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
drm core no longer uses crtc->hwmode, and neither does i915, so we can totally ignore it
in i915.
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
We don't really use hwmode anymore in i915, so eliminating its use
from the core code seems prudent. Just pass the appropriate mode
to drm_calc_timestamping_constants().
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Conflicts are getting out of hand, and now we have to shuffle even
more in -next which was also shuffled in -fixes (the call for
drm_mode_config_reset needs to move yet again).
So do a proper backmerge. I wanted to wait with this for the 3.13
relaese, but alas let's just do this now.
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_pm.c
Besides the conflict around the forcewake get/put (where we chaged the
called function in -fixes and added a new parameter in -next) code all
the current conflicts are of the adjacent lines changed type.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The intel_encoder_crtc_ok() is a duplicate of the drm_encoder_crtc_ok()
function that used to be only available in the DRM CRTC helpers. It has
recently been moved to the core, so the duplicate can now be dropped.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There's no LVDS port on 830M so don't go reading the LVDS control
register.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PFIT_CONTROL doesn't exist on 830M, so avoid reading it in
i9xx_get_pfit_config().
Also assume that only mobile gen2/3 chipsets have a panel fitter. This
matches the documentation, but I didn't have real hardware to verify.
Gen4 docmentation is a bit inconsistent, but experimenetation on my
LPT machine suggests that the panel fitter is available on non-mobile
gen4 platforms. At least on this machine panel fitter appears works
just fine even on VGA output.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VGA detection requires the reference clock to be on, so make sure this
is the case.
This fixes VGA hotplug/manual detection where all pipes are off and so
we would normally disable all clocks.
v2:
- Instead of disabling PSR clock gating, force the reference clock on
through the DPLL_A register. (Kin Chan S <kin.s.chan@intel.com>)
v3:
- Move enabling of the clock to intel_reset_dpio() and use the DPLL_B
register instead, where we already have a similar tweak for the CRI
clock. (Ville)
Reported-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_init_dpio() isn't called during resume, so we won't set the CRI
clock enable bit during that time. Move the enabling to
intel_reset_dpio() instead.
Note that the HW reset value for this bit is 1, so probably this patch
won't make any difference. We should still make the setting explicit,
since BIOS could change things under us.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The WA is mentioned in HSW's GAMMA_MODE register documentation, but
not on on BDW's documentation, so let's assume it is not needed there.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That we can use for debugging purposes.
v2: Use designated initializers for the 'names' array (Paulo Zanoni,
Jani Nikula).
Add a check in case the array has a hole (which can now remain
unnoticed with designated initializers) (Jani Nikula)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (for v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In some cases we have more than 1 connector associated to an encoder
(e.g., SDVO, Haswell DP/HDMI) and we can only set a mode for one of
these connectors. If we only allowed modesets for connected connectors
we would never need this patch, but since we do allow modeset for
disconnected connectors we may see user space trying to set modes on
the two connectors attached to the same encoder, so we need to forbid
that.
This problem can be reproduced by running the following
intel-gpu-tools test case:
./kms_setmode --run-subtest clone-exclusive-crtc
Thanks to Daniel Vetter for providing a version of this patch on
pastebin.
Credits-to: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My OCD just couldn't let this slide. Spotted while reviewing Ville's
patch to only flip planes when we have FBC.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like 830M doesn't quite like it when you try to move a plane from
one pipe to another. It seems that the plane's old pipe has to be active
even if the plane is already disabled, otherwise the relevant register
just won't accept new values.
The following commit:
commit 1f1c2e2468
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Nov 28 17:30:01 2013 +0200
drm/i915: Swap primary planes on gen2 for FBC
caused a regression on 830M. It will attempt to swap the planes when the
driver is loaded, but at that time only pipe A might be active, so plane
A gets disabled, but plane B won't get enabled since pipe B is not
active when we try to move the plane over to pipe A.
There's no reason to swap planes on 830M since it doesn't support
FBC. Change the logic a bit to limit the plane swapping to platforms
which actually support FBC. This should avoid getting a black screen on
830M.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the pipe A force quirk is applied the code will attempt to grab
a crtc mutex during intel_modeset_setup_hw_state(). If we're already
holding all crtc mutexes this will obviously deadlock every time.
So instead of using drm_modeset_lock_all() just grab the
mode_config.mutex. This is enough to avoid the unlocked mutex warnings
from certain lower level functions.
The regression was introduced in:
commit 0274766428
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Dec 2 11:08:06 2013 +0200
drm/i915: Take modeset locks around intel_modeset_setup_hw_state()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
[danvet: Add cc: stable since the offending commit has that, too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
LPT does have PCH refclk, but it's different form the IBX/CPT/PPT one
and doesn't use the same structs. It is wrong to have a message saying
that "LPT does not has PCH refclk" (sic). While at it, signal that we
only want this function on IBX/CPT/PPT by renaming it and adding a
WARN.
On HSW we also print "0 shared PLLs initialized", but we *do* have
shared PLLs on HSW (LCPLL, WRPLL, SPLL) and we *do* initialize them.
We just don't use "struct intel_shared_dpll". So remove the debug
message.
In the future we may want to rename all that "intel shared pll" code
to "ibx shared pll", but I'll leave this to another patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to Art, we don't have a way to read back the state reliably at
runtime, through the control reg or the mailbox, at least not without risking
disabling it again. So drop the readout and checking on BDW.
v2: drop TODO comment (Paulo)
move POSTING_READ of control reg under HSW branch in disable (Paulo)
always report IPS as enabled on BDW (Paulo)
References: https://bugs.freedesktop.org/show_bug.cgi?id=71906
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When fastbooting, we read out the pipe timings early on, and then in a
panel fitted config, disable the fitter later. But we weren't updating
the pipe src h/w, which meant the mouse cursor was clipped to the
pfitted size rather than the native size set later. Fix that up so the
cursor is visible in the new mode.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we won't check the state until the next DPMS transition, which
may never happen.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're iterating over the CPU transcoders, so check for the correct
power domain.
This fixes many "unclaimed register" error messages.
This can be reproduced by the IGT test mentioned below, but we still
get a FAIL when we run it.
Testcase: igt/kms_lip/flip-vs-panning-vs-hang
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My Acer 8510TZ stops displaying anything when X starts with Linus' current
tree. I bisected it down to commit ee1452d745.
This patch reverts commit ee1452d745.
After the revert, everything works as before.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Reported-by: Dylan Borg <borgdylan@hotmail.com> (for a Acer Extensa 5635Z)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The GMCH_CTRL register (or MGCC in the spec) is at a different address
on Sandybridge, and the address to which we currently write to is
undefined. These stray writes appear to upset (hard hang) my Ivybridge
machine whilst it is in UEFI mode.
Note that the register is still marked as locked RO on Sandybridge, so
vgaarb is still dysfunctional.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new HSW watermark code can now handle ILK/SNB/IVB as well, so
switch them over. Kill the old code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only need to init the reg offset for DPIO once, but we need to reset
DPIO at resume time and at init time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just add an early init since we may need to access DPIO regs early on.
The init call in modeset_init_hw is also needed for the resume case,
when we need to reset DPIO to keep things happy.
v2: split reset and reg init
v3: split patches (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, PC8 is enabled at modeset_global_resources, which is called
after intel_modeset_update_state. Due to this, there's a small race
condition on the case where we start enabling PC8, then do a modeset
while PC8 is still being enabled. The racing condition triggers a WARN
because intel_modeset_update_state will mark the CRTC as enabled, then
the thread that's still enabling PC8 might look at the data structure
and think that PC8 is being enabled while a pipe is enabled. Despite
the WARN, this is not really a bug since we'll wait for the
PC8-enabling thread to finish when we call modeset_global_resources.
The spec says the CRTC cannot be enabled when we disable LCPLL, so we
had a check for crtc->base.enabled. If we change to crtc->active we
will still prevent disabling LCPLL while the CRTC is enabled, and we
will also prevent the WARN above.
This is a replacement for the previous patch named
"drm/i915: get/put PC8 when we get/put a CRTC"
Testcase: igt/pm_pc8/modeset-lpsp-stress-no-wait
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
(cherry picked from commit 798183c547
from -next due to Dave's report.)
Reported-by: Dave Jones <davej@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The first piece, intel_ddi_pll_select, finds a PLL and assigns it to
the CRTC, but doesn't write any register. It can also fail in case it
doesn't find a PLL.
The second piece, intel_ddi_pll_enable, uses the information stored by
intel_ddi_pll_select to actually enable the PLL by writing to its
register. This function can't fail. We also have some refcount sanity
checks here.
The idea is that one day we'll remove all the functions that touch
registers from haswell_crtc_mode_set to haswell_crtc_enable, so we'll
call intel_ddi_pll_select at haswell_crtc_mode_set and then call
intel_ddi_pll_enable at haswell_crtc_enable. Since I'm already
touching this code, let's take care of this particular split today.
v2: - Clock on the debug message is in KHz
- Add missing POSTING_READ
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Bikeshed comments.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On my 855 machine the BIOS uses the following DPLL settings:
DPLL 0x90016000
FP0 = 0x61207
FP1 = 0x21207
With the 66MHz SSC refclock, that puts the BIOS generated VCO
frequency at ~908 MHz, which is lower than the 930 MHz limit
we have currently. This also results in the pixel clock coming
out significantly higher than the requested 65 MHz when we try
to recompute it.
Reduce the the VCO limit to 908 MHz. Combined with the earlier
SSC reference clock accuracy fix, this results in the pixel clock
coming out as 65.08 MHz which is quite close to the target. For
some reason the BIOS uses 64.881 MHz, which isn't quite as close.
This makes kms_flip wf_vblank-ts-check pass for the first time
on this machine \o/
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Store the SSC refclock frequency in kHz to get more accuracy. Currently
we're pretending that 66 MHz is ~66000 kHz, when in fact it is actually
~66667 kHz. By storing the less rounded kHz value we get a much better
accuracy for out pixel clock calculations.
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bruno Prémont has a 855 machine with a 1400x1050 LVDS screen.
The VBT mode is as follows:
0:"1400x1050" 0 108000 1400 1416 1528 1688 1050 1051 1054 1066 0x8 0xa
The BIOS uses the following DPLL settings:
DPLL = 0x90020000
FP0 = 0x2140e
FP1 = 0x21207
That puts the BIOS generated VCO frequency at 1512 MHz, which is
higher than the 1400 MHz limit we have currently.
Let's bump the VCO limit to 1512 MHz and see what happens.
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bruno Prémont has a 855 machine with a 1400x1050 LVDS screen.
The VBT mode is as follows:
0:"1400x1050" 0 108000 1400 1416 1528 1688 1050 1051 1054 1066 0x8 0xa
The BIOS uses the following DPLL settings:
DPLL = 0x90020000
FP0 = 0x2140e
FP1 = 0x21207
We can't generate that pixel clock currently as we're limiting the N
divider to at least 3, whereas the BIOS uses a value of 2.
Let's reduce the N minimum to 2 and see what happens.
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to determine the correct p2 divider for LVDS on gen2,
we need to check the CLKB mode from the LVDS port register to
determine if we're dealing with single or dual channel LVDS.
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code to enable/disable PC8 already takes care of saving and
restoring all the registers we need to save/restore, so do a put()
call when we enable PC8 and a get() call when we disable it.
Ideally, in order to make it easier to add runtime PM support to other
platforms, we should move some things from the PC8 code to the runtime
PM code, but let's do this later, since we can make Haswell work right
now.
V2: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Don't actually enable runtime pm since I didn't merge all
patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code was checking if all bits of "val" were enabled and
DE_PCH_EVENT_IVB was disabled. The new code doesn't care about the
state of DE_PCH_EVENT_IVB: it just checks if everything else is 1.
The goal is that future patches may completely disable interrupts, and
the LCPLL-disabling code shouldn't care about the state of
DE_PCH_EVENT_IVB.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: I think the commit message is actually wrong in it's
description of what the old test checked, but the new one seems sane.
So meh.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already have some checks and shouldn't be reaching these places on
!HAS_PC8 platforms, but add a WARN, just in case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The CRI clock is related to the display PHY, so the setup belongs
in intel_init_dpio().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSogqUAAoJEHm+PkMAQRiGM2MIAJrr5KEXEWuuAR4+JkkWBK7A
+dVT4n1MM4wP/aCIyriSlq7kgT03Wxk4Q4wKsj2wZvDQkNgEQjrctgIihc75jqi5
126nmT3YXJLwgDpFA3RHZUWve3j3vfUG53rRuk7K9Xx1sGWU3Ls7BuInvQZ//+QS
6UB4UuEAalmose5U8ToXQfMqZhjwreZKeb64TEZwFvu2klv4cnka1L/zHbmQGgRg
2Pfv+aUrjsYE8s9lkEKX8MIQsDn28Q5Lsv7XIEQwo2at4rYbJaxX6usuC1OI0MQ5
BLUn1GgtvOidq6FzSg6kXiA/MJYH3J0S+p4uULWAprxA+KeJRbWNRroM94W1qAk=
=1Wcq
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc3' into drm-intel-next-queued
Linux 3.13-rc3
I need a backmerge for two reasons:
- For merging the ppgtt patches from Ben I need to pull in the bdw
support.
- We now have duplicated calls to intel_uncore_forcewake_reset in the
setup code to due 2 different patches merged into -next and 3.13.
The conflict is silen so I need the merge to be able to apply
Deepak's fixup patch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Trivial conflict, it doesn't even show up in the merge diff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, PC8 is enabled at modeset_global_resources, which is called
after intel_modeset_update_state. Due to this, there's a small race
condition on the case where we start enabling PC8, then do a modeset
while PC8 is still being enabled. The racing condition triggers a WARN
because intel_modeset_update_state will mark the CRTC as enabled, then
the thread that's still enabling PC8 might look at the data structure
and think that PC8 is being enabled while a pipe is enabled. Despite
the WARN, this is not really a bug since we'll wait for the
PC8-enabling thread to finish when we call modeset_global_resources.
The spec says the CRTC cannot be enabled when we disable LCPLL, so we
had a check for crtc->base.enabled. If we change to crtc->active we
will still prevent disabling LCPLL while the CRTC is enabled, and we
will also prevent the WARN above.
This is a replacement for the previous patch named
"drm/i915: get/put PC8 when we get/put a CRTC"
Testcase: igt/pm_pc8/modeset-lpsp-stress-no-wait
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only plane A is FBC capable on gen2 (like gen3), but the panel fitter
is hooked up to pipe B, so we want to prefer pipe B + plane A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add the code comment Chris requested in his review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't have clock state readout support for DDI, so skip the pipe
config clock checks on all DDI platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We call intel_modeset_setup_hw_state() along two paths, driver
load/resume and after a lid event notification. During initialisation of
the driver, it is imperative that we reset the config state. This
correctly sets up the initial connector statuses and prepares the
hardware for a thorough probing. However, during a lid event, we only
want to undo the damage caused by the bios by resetting our last known
mode. In this cirumstance, we do not want to clobber our desired state.
In order to try and keep sanity between the config state and our own
tracking, do the drm_mode_config_reset() first along the load/resume
paths before reading out the hw state and apply any definite known
corrections.
v2: "As discussed on irc I don't think we should force the connector
state to anything here: Imo connector->status should reflect what we
believe to be the true output connection state, whereas connector->encoder
reflects whether this connector is wired up to a pipe. And since we no
longer reject modeset on disconnected connectors and never nuked the pipe
if the connector gets disconnected there's no reason for that - such policy
is userspace's job.
This regression has been introduced in
commit 2e9388923e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 11 20:08:24 2012 +0200
drm/i915/crt: explicitly set up HOTPLUG_BITS on resume"
so sayeth Daniel.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org (v3.8 and later)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some lower level things get angry if we don't have modeset locks
during intel_modeset_setup_hw_state(). Actually the resume and
lid_notify codepaths alreday hold the locks, but the init codepath
doesn't, so fix that.
Note: This slipped through since we only disable pipes if the
plane/pipe linking doesn't match. Which is only relevant on older
gen3 mobile machines, if the BIOS fails to set up our preferred
linking.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Tested-and-reported-by: Paul Bolle <pebolle@tiscali.nl>
[danvet: Add note now that I could confirm my theory with the log
files Paul Bolle provided.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check that the N and P dividers don't cause a divide by zero.
This shouldn't happen under normal circumstances, but can
happen eg. under simulation.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're currently misprinting the port name when vlv_wait_port_ready()
times out. Fix it by using port_name().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ring scratch pages don't have a PPGTT mapping, so the DERRM SRM
should target the global GTT instead.
v2: Add MI_SRM_LRM_GLOBAL_GTT define for -fixes
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When I submitted the first patch adding these force wake functions,
Chris Wilson observed that I was using the wrong functions, so I sent
a second version of the patch to correct this problem. The problem is
that v1 was merged instead of v2.
I was able to notice the problem when running the
debugfs-forcewake-user subtest of pm_pc8 from intel-gpu-tools.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were miscalculating the pipe CSC post offset for the full->limited
range conversion. The resulting post offset was double what it was
supposed to be, which caused blacks to come out grey when using
limited range output on HSW+.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71769
Cc: stable@vger.kernel.org
Tested-by: Lauri Mylläri <lauri.myllari@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we call intel_display_power_enabled() from
i915_capture_error_state() in IRQ context and then take a mutex. To fix
this add a new intel_display_power_enabled_sw() which returns the domain
state based on software tracking as opposed to reading the actual HW
state.
Since we use domain_use_count for this without locking on the reader
side make sure we increase the counter only after enabling all required
power wells and decrease it before disabling any of these power wells.
Regression introduced in
commit 1b02383464b4a915627ef3b8fd0ad7f07168c54c
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Sep 24 16:17:09 2013 +0300
drm/i915: support for multiple power wells
Note that atm we depend on the value returned by
intel_display_power_enabled_sw() in i915_capture_error_state() to avoid
unclaimed register access reports. This was never guaranteed though,
since another thread can disable the power concurrently. If this is a
problem we need another explicit way to disable the reporting during
error captures.
v2:
- remove barriers as the caller can't depend on the value
returned from i915_capture_error_state_sw() anyway (Ville)
- dump the state of pipe/transcoder power domain state (Daniel)
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV can have eDP on either port B or C, or even both. Based on the
VBT spec, intel_dpd_is_edp() should work on VLV too, assuming we
check the correct ports.
So instead of hardcoding port D, rename the function to
intel_dp_is_edp() and pass the port as a parameter, and use it
on VLV ports B and C.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71051
Tested-by: Robert Hooker <robert.hooker@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Wrestle the patch to apply and compile properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added power well arguments to all the force wake routines
to help us individually control power well based on the
scenario.
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with the removed forcewake hack and drop one
spurious hunk Jesse noticed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to user fudging (for instance using video=VGA-1:e with FBDEV=n) we can
attempt to reset an inconsistent CRTC that is marked as active but has
no assigned fb. It would be wise to fix this earlier, but the long
term plan is to have primary and secondary planes associated with a
CRTC, in which crtc->fb being NULL will be expected. So for a quick
short term fix with pretensions of grandeur, just check for a NULL fb
during GPU reset and ignore the plane restoration.
This fixes a potential hard hang (a panic in the panic handler)
following a GPU hang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Add a corresponding fixme comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This may need work if other platforms do the same thing, but in the
meantime we should avoid looking at HSW specific bits in this generic
function.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[added IS_BROADWELL too as that needs the same handling (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
[danvet: Add Imre's missing sob.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In intel_display_capture_error_state we use HAS_POWER_WELL to check if
we are running on Haswell/Broadwell when accessing HSW_PWR_WELL_DRIVER
which is specific to these platforms. Future platforms with power wells
don't have this register, so HAS_POWER_WELL won't work there any more.
Use IS_HASWELL/IS_BROADWELL instead.
v3: fix using logical || instead of bitwise | (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to hold the pc8 lock around toggling the value of gpu_idle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the hardware does not support package C8, then do not even schedule
work to enable it. Thereby we can eliminate a bunch of dangerous work.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to hold the pc8 lock around toggling the value of gpu_idle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We must have one to fill out the adjusted_mode.crtc_clock. And with
the tv encoder fixed up every encoder we have has a ->get_config
callback. So we can drop the checks.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently they need the same treatment as primary planes. This fixes
modesetting failures because of stuck cursors (!) on Thomas' i830M
machine.
I've figured while at it I'll also roll it out for the ivb 3 pipe
version of this function. I didn't do this for i845/i865 since Bspec
says the update mechanism works differently, and there's some
additional rules about what can be updated in which order.
Tested-by: Thomas Richter <thor@math.tu-berlin.de>
Cc: stable@vger.kernel.org
Cc: Thomas Richter <thor@math.tu-berlin.de>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The quirk was added as what I'd say was a stopgap measure in
commit e85843bec6
Author: Kamal Mostafa <kamal@canonical.com>
Date: Fri Jul 19 15:02:01 2013 -0700
drm/i915: quirk no PCH_PWM_ENABLE for Dell XPS13 backlight
without really digging into what was going on.
Also, as mentioned in the related bug [1], having the quirk regressed
some of the machines it was supposed to fix to begin with, and there
were patches posted to disable the quirk on such machines [2]!
The fact is, we do need the BLM_PCH_PWM_ENABLE bit set to have
backlight. With the quirk, we've relied on BIOS to have set it, and our
save/restore code to retain it. With the full backlight setup at enable,
we have no place for things that rely on previous state.
With the per platform hooks, we've also made a change in the PCH
platform enable order: setting the backlight duty cycle between CPU and
PCH PWM enable. Some experimenting and
commit 770c12312a
Author: Takashi Iwai <tiwai@suse.de>
Date: Sat Aug 11 08:56:42 2012 +0200
drm/i915: Fix blank panel at reopening lid
indicate that we can't set the backlight before enabling CPU PWM; the
value just won't stick. But AFAICT we should do it before enabling the
PCH PWM.
Finally, any fallout we should fix properly, preferrably without quirks,
and absolutely without quirks that rely on existing state. With the per
platform hooks have much more flexibility to adjust the sequence as
required by platforms.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=47941
[2] http://lkml.kernel.org/r/1378229848-29113-1-git-send-email-kamal@canonical.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The backlight code has grown rather hairy, not least because the
hardware registers and bits have repeatedly been shuffled around. And
this isn't expected to get any easier with new hardware. Make things
easier for our (read: my) poor brains, and split the code up into chip
specific functions.
There should be no functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've always felt the backlight device conditional build has been all
backwards. Make it feel right.
Gently move things towards connector based stuff while at it.
There should be no functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv_dpio_read/write should be describe more in PHY centric instead of
display controller centric.
Create a enum dpio_channel for channel index and enum dpio_phy for PHY
index. This should better to gather for upcoming platform.
v2: Rebase the code based on
drm/i915/vlv: Fix typo in the DPIO register define.
v3: Rename vlv_phy to dpio_phy_iosf_port and define additional macro
DPIO_PHY, and remove unrelated change. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's the Broadwell pull request. From a kernel driver pov there's
two areas with big changes in Broadwell:
- Completely new enumerated interrupt bits. On the plus side it now looks
fairly unform and sane.
- Completely new pagetable layout.
To ensure minimal impact on existing platforms we've refactored both the
irq and low-level gtt handling code a lot in anticipation of the bdw push.
So now bdw enabling in these areas just plugs in a bunch of vfuncs.
Otherwise it's all fairly harmless adjusting of switch cases and
if-ladders to shovel bdw into the right blocks. So minimized impact on
existing platforms. I've also merged the bdw-stage1 branch into our
-nightly integration branch for the past week to make sure we don't break
anything.
Note that there's still quite a flurry or patches floating around, but
I've figured I'll push this out. I plan to keep the bdw fixes separate
from my usual -fixes stream so that you can reject them easily in case it
still looks like too much churn. Also, bdw is for now hidden behind the
preliminary hw enabling module option. So there's no real pressure to get
follow-up patches all into 3.13.
* tag 'bdw-stage1-2013-11-08-v2' of git://people.freedesktop.org/~danvet/drm-intel: (75 commits)
drm/i915: Mask the vblank interrupt on bdw by default
drm/i915: Wire up cpu fifo underrun reporting support for bdw
drm/i915: Optimize gen8_enable|disable_vblank functions
drm/i915: Wire up pipe CRC support for bdw
drm/i915: Wire up PCH interrupts for bdw
drm/i915: Wire up port A aux channel
drm/i915: Fix up the bdw pipe interrupt enable lists
drm/i915: Optimize pipe irq handling on bdw
drm/i915/bdw: Take render error interrupt out of the mask
drm/i915/bdw: Add BDW PCH check first
drm/i915: Use hsw_crt_get_config on BDW
drm/i915/bdw: Change dp aux timeout to 600us on DDIA
drm/i915/bdw: Enable trickle feed on Broadwell
drm/i915/bdw: WaSingleSubspanDispatchOnAALinesAndPoints
drm/i915/bdw: conservative SBE VUE cache mode
drm/i915/bdw: Limit SDE poly depth FIFO to 2
drm/i915/bdw: Sampler power bypass disable
ddrm/i915/bdw: Disable centroid pixel perf optimization
drm/i915/bdw: BWGTLB clock gate disable
drm/i915/bdw: Implement edp PSR workarounds
...
Like on HSW, trickle feed should always be enabled on BDW.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Squash in fixup from Ben to synchronize the GT mailbox commands.
CC: Art Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So treat it like Haswell.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Route cursor and sprite data through the pipe CSC unit on BDW.
Primary plane data is already sent through the pipe CSC.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And it inherits some bits from the previous TRANS_CONF (aka PIPE_CONF
on previous gens).
v2: Rebase on to of the pipe config bpp handling rework.
v3: Rebased on top of the pipe_config->dither refactoring.
v4: Drop the read-modify-write cycle for PIPEMISC, similarly to how we
now also build up PIPECONF completely ourselves - keeping around
random stuff set by the BIOS just isn't a good idea. I've checked BDW
BSpec and we already set all relevant bits.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just make Broadwell follow the same code paths as Haswell here,
instead of running code for the even-older platforms.
v2: Shuffle around Ben's vma prep work.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just enough to make the code not barf...
Init BDW display to look like HSW. For the simulator this should be
fine, but this will probably require more work.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a FIXME comment about RCS flips being untested on bdw.
Also add a note that hblank events are reserved on bdw+ in DERRMR.]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some VLV PHY/PLL DPIO registers have group/lane/channel access. Current
DPIO register definition doesn't have a structure way to break them
down. As a result it is not easy to match the PHY/PLL registers with the
configdb document. Rename those registers based on the configdb for easy
cross references, and without the need to check the offset in the header
file.
New format is as following.
<platform name>_<DPIO component><optional lane #>_DW<dword # in the
doc>_<optional channel #>
For example,
VLV_PCS_DW0 - Group access to PCS for lane 0 to 3 for PCS DWORD 0.
VLV_PCS01_DW0_CH0 - PCS access to lane 0/1, channel 0 for PCS DWORD 0.
Another example is
VLV_TX_DW0 - Group access to TX lane 0 to 3 for TX DWORD 0
VLV_TX0_DW0 - Refer to TX Lane 0 access only for TX DWORD 0.
There is no functional change on this patch.
v2: Rebase based on previous patch change.
v3: There may be configdb different version that document the start DW
differently. Add a comment to clarify. Fix up some mismatch start DW
for second PLL block. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
Use the same wait_for_vblank code for CTG that we use for ILK+.
Also fix the name of the frame counter register while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/BYT, backlight controls a per-pipe, so when adjusting the
backlight we need to pass the correct info. So make the externally
visible backlight functions take a connector argument, which can be used
internally to figure out the pipe backlight to adjust.
v2: make connector pipe lookup check for NULL crtc (Jani)
fixup connector check in ASLE code (Jani)
v3: make sure we take the mode config lock around lookups (Daniel)
v4: fix double unlock in panel_get_brightness (Daniel)
v5: push ASLE work into a work queue (Daniel)
v6: separate ASLE work to a prep patch, rebase (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
valleyview_modeset_global_pipes() may add pipes that are getting fully
disabled to prepare_pipes bitmask. The rest of the code doesn't expect
this, so clear out any such pipes from the prepare_pipes bitmask.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's be a bit more consistent with our error values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's possible that the CCK clock could run at a different rate than the
DDR clock, so use the same method to get CCK as the GMBUS code does when
calculating the new CDclk divider in the VLV display code.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/BYT, we can adjust the CDclk frequency up or down based on the
max pixel clock we need to drive. Lowering it can save power, while
raising it is necessary to support high resolution.
Add a new callback in modeset_affected_pipes and a
modeset_global_resources function to perform this adjustment as
necessary.
v2: use punit interface for 320 and 266 MHz CDclk adjustments (Ville)
v3: reset GMBUS dividers too, since we changed CDclk (Ville)
v4: jump to highest voltage when going to 400MHz CDclk (Jesse)
v5: drop duplicate define (Ville)
use shifts by 1 for fixed point (Ville)
drop new callback (Daniel)
v6: fixup adjusted_mode.clock -> adjusted_mode.crtc_clock again (Ville)
document Bunit reg access better (Ville)
v7: pass modeset_pipes and pipe_config to global_pipes so we get the right
clock data (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines HD-Audio configuration registers and enables display audio
from HDA controller for Valleyview2.
v2: fix missing offset VLV_DISPLAY_BASE
v3: rename patch from 'enable HDMI audio' to 'enable HDA display audio', since
it's for both HDMI and DP audio
v4: use enc_to_dig_port() to get port number, instead of using Haswell specific
function intel_ddi_get_encoder_port()
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even though we only check for unclaimed registers while we're writing
registers, if we read a bad register we'll still trigger a CPU error
interrupt, and we'll print an "Unclaimed register" DRM_ERROR due to
that. To avoid this error, just avoid touching power domains that are
not enabled.
Use kzalloc so we're sure all the disabled domains will be zeroed on
the error state file. We already print the information that is enough
to discover if the power well is enabled on the error state file, so
this should not be a problem.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69747
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Originally I've thought that this is leftover hw state dirt from the
BIOS. But after way too much helpless flailing around on my part I've
noticed that the actual bug is when we change the state of an already
active pipe.
For example when we change the fdi lines from 2 to 3 without switching
off outputs in-between we'll never see the crucial on->off transition
in the ->modeset_global_resources hook the current logic relies on.
Patch version 2 got this right by instead also checking whether the
pipe is indeed active. But that in turn broke things when pipes have
been turned off through dpms since the bifurcate enabling is done in
the ->crtc_mode_set callback.
To address this issues discussed with Ville in the patch review move
the setting of the bifurcate bit into the ->crtc_enable hook. That way
we won't wreak havoc with this state when userspace puts all other
outputs into dpms off state. This also moves us forward with our
overall goal to unify the modeset and dpms on paths (which we need to
have to allow runtime pm in the dpms off state).
Unfortunately this requires us to move the bifurcate helpers around a
bit.
Also update the commit message, I've misanalyzed the bug rather badly.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70507
Tested-by: Jan-Michael Brummer <jan.brummer@tabos.org>
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We store cursor_x/y as int16_t internally, but the user provided
coordinates are int32_t. Clamp the coordinates so that they don't
overflow the int16_t. Since the cursor is only 64x64 in size, the
clamping can't cause any visual changes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CTG+ read out the pipe bpp setting from hardware and fill it into
pipe config. Also check it appropriately.
v2: Don't do the pipe_bpp extraction inside the PCH only code block on
ILK+.
Avoid the PIPECONF read as we already have read it for the
PIPECONF_EANBLE check.
Note: This is already in drm-intel-next-queued as
commit 42571aefaf
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 6 23:29:00 2013 +0300
drm/i915: Add support for pipe_bpp readout
but is needed for the following bugfix.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we make sure that all power domains are enabled during driver
init and turn off unneded ones only after the first modeset. Similarly
during suspend we enable all power domains, which will remain on through
the following resume until the first modeset.
This logic is supported by intel_set_power_well() in the power domain
framework. It would be nice to simplify the API, so that we only have
get/put functions and make it more explicit on the higher level how this
"power well on during init" logic works. This will make it also easier
if in the future we want to shorten the time the power wells are on.
For this add a new device private flag tracking whether we have the
power wells on because of init/suspend and use only
intel_display_power_get()/put(). As nothing else uses
intel_set_power_well() we can remove it.
This also fixes
commit 6efdf354dd
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Oct 16 17:25:52 2013 +0300
drm/i915: enable only the needed power domains during modeset
where removing intel_set_power_well() resulted in not releasing the
reference on the power well that was taken during init and thus leaving
the power well on all the time. Regression reported by Paulo.
v2:
- move the init_power_on flag to the power_domains struct (Daniel)
v3:
- add note about this being a regression fix too (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far the modeset code enabled all power domains if it needed any. It
wasn't a problem since HW generations so far only had one always-on
power well and one dynamic power well that can be enabled/disabled. For
domains powered by always-on power wells (panel fitter on pipe A and the
eDP transcoder) we didn't do anything, for all other domains we just
enabled the single dynamic power well.
Future HW generations will change this, as they add multiple dynamic
power wells. Support for these will be added later, this patch prepares
for those by making sure we only enable the required domains.
Note that after this change on HSW we'll enable all power domains even
if it was the domain for the panel fitter on pipe A or the eDP
transcoder. This isn't a problem since the power domain framework
already checks if the domain is on an always-on power well and doesn't
do anything in this case.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll need the same functionality for other HW generations. The support
for these will be added by upcoming patches.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jun 5 13:34:23 2013 +0200
drm/i915: consolidate pch pll enable sequence
I've removed all the code from this if block, but somehow forgotten to
kill the block itself.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The HDMI audio expects HDMI pixel clock to be set in the audio
configuration. We've currently just set 0, using 25.2 / 1.001 kHz
frequency, which fails with some modes.
v2: Now with a commit message.
Reference: http://mid.gmane.org/CAGpEb3Ep1LRZETPxHGRfBDqr5Ts2tAc8gCukWwugUf1U5NYv1g@mail.gmail.com
Reference: http://mid.gmane.org/20130206213533.GA16367@hardeman.nu
Reported-by: David Härdeman <david@hardeman.nu>
Reported-by: Jasper Smet <josbeir@gmail.com>
Tested-by: Jasper Smet <josbeir@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed for setting the HDMI pixel clock for audio
config. No functional changes.
v2: Now with a commit message.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's better to catch such fallout early, and this way we can rely on
the checking done by the drm core on fb->heigh/width at modeset time.
If we ever support planar formats on intel we might want to look into
a common helper to do all this, but for now this is good enough.
v2: Take tiling into account, requested by Ville.
v3: Fix tile height on gen2, spotted by Ville.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Assuming that all framebuffer related metadata is invariant simplifies
our userspace input data checking. And current userspace always first
updates the tiling of an object before creating a framebuffer with it.
This allows us to upconvert a check in pin_and_fence to a WARN.
In the future it should also be helpful to know which buffer objects
are potential scanout targets for e.g. frontbuffer rendering tracking
and similar things.
Note that SNA shipped for one prerelease with code which will be
broken through this patch. But users shouldn't notice since it's
purely an optimization and will transparently fall back to allocating
a new fb. i-g-t also had offending code (now fixed), but we don't
really care about breaking the test-suite.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Grumpily-reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We look at gem state (like obj->tiling/obj->stride), we better have
the relevant locks.
Right now this doesn't matter much since most of these checks are
a curtesy to safe buggy userspace, but I'd like to freeze the tiling
once we have framebuffer objects attached. And then locking matters.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch changes HDMI port registration order for the BayTrail platform.
The story is that in kernel version 3.11 i915 supported only one HDMI port -
the HDMIB port. So this port ended up being HDMI-1 in user-space.
But commit '6f6005a drm/i915: expose HDMI connectors on port C on BYT'
introduced HDMIC port support. And added HDMIC registration prior to HDMIB,
so HDMIB became HDMI-2 and HDMIC became HDMI-1.
Well, this is fine as far as the kernel is concerned. i915 does not give any
guarantees to the numbering, and has never given them.
However, this breaks wayland setup in Tizen IVI. We have only one single HDMI
port on our hardware, and it is connected to HDMIB. Our configuration relies on
the fact that it is HDMI-1.
Well, certainly this is user-space problem which was exposed with Jesse's
patch. However, there is a reason why we have to do this assumption - we use
touchscreen monitors and we have to associate event devices with the monitors,
and this is not easy to do dynamically, so we just have a static setup.
Anyway, while the user-space setup will have to be fixed regardless, let's
chane the HDMI port registration order so that HDMIB stays HDMI-1, just like it
was in 3.11. Simply because there is no strong reason for changing the order in
the kernel, and it'll help setups like ours in sense that we'll have more time
for fixing the issue properly.
Also amend the commentary which looks a bit out-of-date.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[danvet: Drop the commment, SDVOC is gone and we have a proper HDMIC
define now.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Yet other direct usages of the pipe number instead of pipe_name().
We've been tracking them lately but managed to miss these last ones.
v2: Catch them all! (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fill out the HSW watermark s/w tracking structures with the current
hardware state in intel_modeset_setup_hw_state(). This allows us to skip
the HW state readback during watermark programming and just use the values
we keep around in dev_priv->wm. Reduces the overhead of the watermark
programming quite a bit.
v2: s/init_wm/wm_get_hw_state
Remove stale comment about sprites
Make DDB partitioning readout safer
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix whitespace fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rounding down when calculating the dot/vco frequencies doesn't make much
sense. Round to closest should give slightly nicer answers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This file is all about the legacy fbdev support. If we want to extract
framebuffer functions, we better put those into a separate file.
Also rename functions accordingly, only two have used the intel_fb_
prefix anyway.
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Boots Just Fine (tm)!
The only glitch seems to be that at least on Fedora the boot splash
gets confused and doesn't display much at all.
And since there's no ugly console flickering anymore in between, the
flicker while switching between X servers (VT support is still enabled)
is even more jarring.
Also, I'm unsure whether we don't need to somehow kick out vgacon, now
that nothing else gets in the way. But stuff seems to work, so I
don't care. Also everything still works as well with VGA_CONSOLE=n
Also the #ifdef mess needs a bit of a cleanup, follow-up patches will
do just that.
To keep the Kconfig tidy, extract all the i915 options into its own
file.
v2:
- Rebase on top of the preliminary hw support option and the
intel_drv.h cleanup.
- Shut up warnings in i915_debugfs.c
v3: Use the right CONFIG variable, spotted by Chon Ming.
Cc: Lee, Chon Ming <chon.ming.lee@intel.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current pre-gen4 pipe off code might break out of the loop
due to the timeout, but then the fail to print the warning.
Refactor the code a bit to use wait_for() to avoid the problem,
and that we also re-check the condition after the timeout has
expired.
v2: Use wait_for()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 81b5c7bc8d.
Adding drm/i915 into the vga arbiter chain means that X (in a piece of
well-meant paranoia) will do a get/put on the vga decoding around
_every_ accel call down into the ddx. Which results in some nice
performance disasters [1]. This really breaks userspace, by disabling
DRI for everyone, and stops OpenGL from working, this isn't limited
to just the i915 but both the integrated and discrete GPUs on
multi-gpu systems, in other words this causes untold worlds of pain,
Ville tried to come up with a Great Hack to fiddle the required VGA
I/O ops behind everyone's back using stop_machine, but that didn't
really work out [2]. Given that we're fairly late in the -rc stage for
such games let's just revert this all.
One thing we might want to keep is to delay the disabling of the vga
decoding until the fbdev emulation and the fbcon screen is set up. If
we kill vga mem decoding beforehand fbcon can end up with a white
square in the top-left corner it tried to save from the vga memory for
a seamless transition. And we have bug reports on older platforms
which seem to match these symptoms.
But again that's something to play around with in -next.
References: [1] http://lists.x.org/archives/xorg-devel/2013-September/037763.html
References: [2] http://www.spinics.net/lists/intel-gfx/msg34062.html
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 6e1b4fdad5.
This is part of a revert due to a userspace breakage, better explained in the revert of 1a1a4cbf4906a13c0c377f708df5d94168e7b582.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Let's try to avoid these confusing negated booleans.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the end of haswell_crtc_enable we have an intel_wait_for_vblank
with a big comment, and the message suggests it's a workaround for
something we don't really understand. So I removed that wait and
started getting HW state readout error messages saying that the IPS
state is not what we expected.
I investigated and concluded that after you write IPS_ENABLE to
IPS_CTL, the bit will only actually become 1 on the next vblank. So
add code to wait for the IPS_ENABLE bit. We don't really need this
wait right now due to the wait I already mentioned, but at least this
one has a reason to be there, while the other one is just to
workaround some problem: we may remove it in the future.
The wait also acts as a POSTING_READ which we missed.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PIPEA quirk is specifically for the issue with the PIPEB PLL on
830gm being slaved to the PIPEA PLL, and so to use PIPEB requires PIPEA
running. i845 doesn't even have the second PLL or pipe, and enabling
the quirk results in a blank DVO LVDS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new names make it clearer which plane we're talking about.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Resolve small conflict with the haswell_crtc_disable_planes
extraction.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The intel_flush_primary_plane name actually tells us which plane
we're talking about.
Also reorganize the internals a bit and add a missing POSTING_READ()
to make sure the hardware has seen the changes by the time we
return from the function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IPS should be OK as long as one plane is enabled on the pipe, but
it does seem to cause problems when going between primary only and
sprite only.
This needs more investigations, but for now just disable IPS whenever
the primary plane is disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the primary gets marked as disabled while the pipe is off for
instance, we should still re-enable it when the pipe is turned on,
unless the sprite covers it fully also in that configuration.
Unfortunately we do the plane visibility checks only in the sprite code,
which is executed after the primary enabling when turning the pipe off.
Ideally we should compute the plane visibility before touching the
hardware at all, but for now just set the primary_disabld flag
in intel_{enable,disable}_plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The VGACNTRL register contains a bunch of other stuff besides
the VGA_DISP_DISABLE bit. When we write the register we always set those
other bits to zero, so normally the current check would work.
However on HSW disabling and re-enabling the power well will reset the
VGACNTRL register to its default value, which has several of the other
bits set as well.
So only look at the VGA_DISP_DISABLE bit when checking whether the VGA
plane needs re-disabling.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Everyone else uses intel_PLL_is_valid(), so make VLV use it as well.
We don't have any special p and m limits on VLV, so skip those tests,
and we also need to skip the m1<=m2 test line PNV.
Reorganize the function a bit to move the n check alongside the rest of
the test for the non-derived dividers, and check the derived values
afterwards.
Note that this changes vlv_find_best_dpll() in two ways:
- The .vco comparison is now >max instead of >=max, and since we round
down when calculating that stuff, we may now allow frequencies slightly
above the max as we do on other platforms. The previous method
disallowed exactly max and anything above it.
- We now check the .dot frequency against the data rate limits, which we
didn't do before.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If vlv_find_best_dpll() couldn't find suitable PLL settings,
just say so instead of lying to caller.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After aligning the p1 divider limits, and removing the unused p and m
limits, intel_limits_vlv_dac and intel_limits_vlv_hdmi are identical.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't use .dot_limit for anything on VLV, so don't populate it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We never check the p and m limits (which according to comments are
based on someone's guesswork), so just remove them.
VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm has no p and m
limits listed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm tells us that the
minimum p2 divider is 2. Use that limit on the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm p1
can be 2-3 always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some reason there's a sort of off by one issue with the p1 divider.
The actual p1 limits according to
VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm is 2-3, so we should
just say that instead of saying 1-3 and avoiding the 1 via the choice of
comparison operator.
I don't know why we're using different p1 limits for intel_limits_vlv_dac
and intel_limits_vlv_hdmi, but let's preserve that for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We limit the maximum n divider value in order to make sure the PLL's
reference inout is at least 19.2 MHz. I assume that is done to satisfy
some hardware requirement.
However we never check whether that calculated limit is below the
maximum supoorted N divider value (7). In practice that is always true
since we only support 100 MHz reference clock, but making the code
safe against higher reference clocks seems like a reasoanble thing to
do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The p2 divider on VLV needs to be even when it's > 10. The current code
to make that happen is rather weird. Just make the step size adjustement
in the for loop decrement step.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite vlv_find_best_dpll() to use intel_clock_t rather than
an army of local variables.
Also extract the code to calculate the derived values into
vlv_clock().
v2: Split up the earlier fixes, extract vlv_clock()
v3: Initialize best_clock
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We do 'bestppm - 10' in vlv_find_best_dpll() but never check whether
that might underflow. Add such a check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use div_u64() to make the ppm calculation in vlv_find_best_dpll() safe
against interger overflows.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When booting with i915.fastboot=1, we always take tha code path and end
up undoing what we're trying to do with adjusted_mode.
Hopefully, as the fastboot hardware readout code is using adjusted_mode
as well, it should be equivalent.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of it just being on the mailing list, let's put Jesse's
explanation next to the code in question.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DPIO needs to have common reset de-asserted on soft resets like boot and
S3. In some cases, the BIOS will have done this for us, but it should
be safe to do at runtime as well, as long as we do it when the pipes are
otherwise off.
v2: update bit name to match docs better (Ville)
reset after CRI clock select (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=69166
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter a situation where the CPU blocks waiting for results
from the GPU, give the GPU a kick to boost its the frequency.
This should work to reduce user interface stalls and to quickly promote
mesa to high frequencies - but the cost is that our requested frequency
stalls high (as we do not idle for long enough before rc6 to start
reducing frequencies, nor are we aggressive at down clocking an
underused GPU). However, this should be mitigated by rc6 itself powering
off the GPU when idle, and that energy use is dependent upon the workload
of the GPU in addition to its frequency (e.g. the math or sampler
functions only consume power when used). Still, this is likely to
adversely affect light workloads.
In particular, this nearly eliminates the highly noticeable wake-up lag
in animations from idle. For example, expose or workspace transitions.
(However, given the situation where we fail to downclock, our requested
frequency is almost always the maximum, except for Baytrail where we
manually downclock upon idling. This often masks the latency of
upclocking after being idle, so animations are typically smooth - at the
cost of increased power consumption.)
Stéphane raised the concern that this will punish good applications and
reward bad applications - but due to the nature of how mesa performs its
client throttling, I believe all mesa applications will be roughly
equally affected. To address this concern, and to prevent applications
like compositors from permanently boosting the RPS state, we ratelimit the
frequency of the wait-boosts each client recieves.
Unfortunately, this techinique is ineffective with Ironlake - which also
has dynamic render power states and suffers just as dramatically. For
Ironlake, the thermal/power headroom is shared with the CPU through
Intelligent Power Sharing and the intel-ips module. This leaves us with
no GPU boost frequencies available when coming out of idle, and due to
hardware limitations we cannot change the arbitration between the CPU and
GPU quickly enough to be effective.
v2: Limit each client to receiving a single boost for each active period.
Tested by QA to only marginally increase power, and to demonstrably
increase throughput in games. No latency measurements yet.
v3: Cater for front-buffer rendering with manual throttling.
v4: Tidy up.
v5: Sadly the compositor needs frequent boosts as it may never idle, but
due to its picking mechanism (using ReadPixels) may require frequent
waits. Those waits, along with the waits for the vrefresh swap, conspire
to keep the GPU at low frequencies despite the interactive latency. To
overcome this we ditch the one-boost-per-active-period and just ratelimit
the number of wait-boosts each client can receive.
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68716
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: No extern for function prototypes in headers.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we ever end up doing the retry loop due to bandwidth constraints, we
would rewrite pipe_src_{w,n} based on adjusted_mode timings. But by that
time the encoder may have already replaced the adjusted_mode with a
fixed panel mode, which would then corrupt pipe_src_{w,h}.
v2: Use requested_mode and slap on a big comment from Daniel
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This workaround is described in the mode set sequence documentation.
When enabling planes for the second pipe, we need to wait for 2
vblanks on the first pipe. This should solve "a flash of screen
corruption if planes are enabled on second/third pipe during the time
that big FIFO mode is exiting". Watermarks are fun :)
v2: Save indentation levels
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Refactor the plane enabling/disabling into helper functions and move
the calls to happen as the first thing during .crtc_disable, and the
last thing during .crtc_enable.
Those are the two clear points where we are sure that the pipe is
actually running regardless of the encoder type or hardware
generation.
v2: Made by Paulo:
Remove the code touching everything but the Haswell functions. We
need this change on Haswell right now since it fixes a FIFO underrun
that we get on pipe A while we enable pipe B (see the workaround
notes on the Haswell mode set sequence documentation). We can bring
back the code to gens 2-7 later, once they're tested.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The global integrated clock source bit resides in DPLL B on VLV, but we
were treating it as a per-pipe resource. It needs to be set whenever
any PLL is active, so pull setting the bit out of vlv_update_pll and
into vlv_enable_pll. Also add a vlv_disable_pll to prevent disabling it
when pipe B shuts down.
I'm guessing on the references here, I expect this to bite any config
where multiple displays are active or displays are moved from pipe to
pipe.
v2: re-add bits in vlv_update_pll to keep from confusing the state checker
v3: use enum pipe checks (Daniel)
set CRI clock source early (Ville)
consistently set CRI clock source everywhere (Ville)
v4: drop unnecessary setting of bit in vlv enable pll (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=67245
References: https://bugs.freedesktop.org/show_bug.cgi?id=69693
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/1/PIPE_B/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some reason, every single time I try to run module_reload
something tries to read the connector sysfs files. This happens
after we destroy the encoders and before we destroy the connectors, so
when the sysfs read triggers the connector detect() function,
intel_conector->encoder points to memory that was already freed.
The bad backtrace is just:
[<ffffffff8163ca9a>] dump_stack+0x54/0x74
[<ffffffffa00c2c8e>] intel_dp_detect+0x1e/0x4b0 [i915]
[<ffffffffa001913d>] status_show+0x3d/0x80 [drm]
[<ffffffff813d5340>] dev_attr_show+0x20/0x60
[<ffffffff81221f50>] ? sysfs_read_file+0x80/0x1b0
[<ffffffff81221f79>] sysfs_read_file+0xa9/0x1b0
[<ffffffff811aaf1e>] vfs_read+0x9e/0x170
[<ffffffff811aba4c>] SyS_read+0x4c/0xa0
[<ffffffff8164e392>] system_call_fastpath+0x16/0x1b
But if you add tons of memory checking debug options to your Kernel
you'll also see:
- general protection fault: 0000
- BUG kmalloc-4096 (Tainted: G D W ): Poison overwritten
- INFO: Allocated in intel_ddi_init+0x65/0x270 [i915]
- INFO: Freed in intel_dp_encoder_destroy+0x69/0xb0 [i915]
Among a bunch of other error messages.
So this commit just destroys the sysfs files before both the encoder
and connectors are freed.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv_find_best_dpll() has an open coded DIV_ROUND_CLOSEST(). Replace it
with the real thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use 'continue' to get rid of one indent level in vlv_find_best_dpll()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we ask to adjust the crtc timings for stereo modes, the correct
pipe_src_w and pipe_src_h can be found in crtc_vdisplay and crtc_hdisplay.
v2: Add comment about why pipe_src_w/h need to be set afert
set_crtcinfo() (Daniel Vetter)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When scanning out big stereo buffers that are actually bigger that their
natural 2D counterpart, we need to blow up the crtc timings as well.
Not that this is only done for frame packing as this is the only stereo
mode currently exposed needing this kind of ajdustements.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).
This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.
v2: Rebased on drm-intel-queued-next
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to dump the parameters given to the hardware, so let's use
crtc_clock here.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With some divider values we end up with the wrong result. So remove the
intermediates (like Ville suggested in the first place) to get the right
answer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calculation is a little different than other platforms.
v2: update to use port_clock instead
rebase on top of Ville's changes
v3: update to new port_clock semantics - don't divide by
pixel_multiplier (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=67345
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions were added before the final PC8 implementation, and
their callers moved to intel_display.c during the code review.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And move it so it doesn't need a forward declaration.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also move it to the top of the file so we can remove the forward
declaration.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Flat out skip anything to do with PLL if we have a DSI encoder (and thus
DSI PLL). Also skip PLL computation if the encoder has already set
clocks. This allows for some tidying up of the code, including a
superfluous call to intel_limit() for LVDS downclock path.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i9xx_crtc_clock_get() no longer populates adjusted_mode.clock, so we
must get the pixel clock from port_clock in intel_crtc_mode_get().
This bug caused Chris's 845g machine to lockup during boot, and it
was introduced in:
commit 18442d0878
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 13 16:00:08 2013 +0300
drm/i915: Fix port_clock and adjusted_mode.clock readout all over
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69713
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already restore planes during the modeset operation, so no need to do
another loop over the planes and try to restore them again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The VGA plane needs to be disabled before we start doing any
modeset operations on resume.
This should also guarantee that the power well will be enabled
when we call i915_redisable_vga() since it gets explicitly powered on
during resume, and will get powered back off during the modeset
operation if no longer needed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the gratious overallocation of crtcs. Seems to go back to the ums
days of yonder ...
We also still need it to make the fbdev emulation happy, but I don't
think there's really a need. Especially since the current fbdev
emulation doesn't actually support cloning.
v2: Use sizeof(*pointer) pattern (Jani).
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No buffer overflows here, but better safe than sorry.
v2:
- Fixup the sizeof conversion, I've missed the pointer deref (Jani).
- Drop the redundant GFP_ZERO, kcalloc alreads memsets (Jani).
- Use kmalloc_array for the execbuf fastpath to avoid the memset
(Chris). I've opted to leave all other conversions as-is since they
aren't in a fastpath and dealing with cleared memory instead of
random garbage is just generally nicer.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the contentious kmalloc_array hunk in execbuf.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done while reviewing all our allocations for fubar. Also a few errant
cases of lacking () for the sizeof operator - just a bit of OCD.
I've left out all the conversions that also should use kcalloc from
this patch (it's only 2).
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2013-09-21:
- clock state handling rework from Ville
- l3 parity handling fixes for hsw from Ben
- some more watermark improvements from Ville
- ban badly behaved context from Mika
- a few vlv improvements from Jesse
- VGA power domain handling from Ville
drm-intel-next-2013-09-06:
- Basic mipi dsi support from Jani. Not yet converted over to drm_bridge
since that was too fresh, but the porting is in progress already.
- More vma patches from Ben, this time the code to convert the execbuffer
code. Now that the shrinker recursion bug is tracked down we can move
ahead here again. Yay!
- Optimize hw context switching to not generate needless interrupts (Chris
Wilson). Also some shuffling for the oustanding request allocation.
- Opregion support for SWSCI, although not yet fully wired up (we need a
bit of runtime D3 support for that apparently, due to Windows design
deficiencies), from Jani Nikula.
- A few smaller changes all over.
[airlied: merge conflict fix in i9xx_set_pipeconf]
* tag 'drm-intel-next-2013-09-21-merged' of git://people.freedesktop.org/~danvet/drm-intel: (119 commits)
drm/i915: assume all GM45 Acer laptops use inverted backlight PWM
drm/i915: cleanup a min_t() cast
drm/i915: Pull intel_init_power_well() out of intel_modeset_init_hw()
drm/i915: Add POWER_DOMAIN_VGA
drm/i915: Refactor power well refcount inc/dec operations
drm/i915: Add intel_display_power_{get, put} to request power for specific domains
drm/i915: Change i915_request power well handling
drm/i915: POSTING_READ IPS_CTL before waiting for the vblank
drm/i915: don't disable ERR_INT on the IRQ handler
drm/i915/vlv: disable rc6p and rc6pp residency reporting on BYT
drm/i915/vlv: honor i915_enable_rc6 boot param on VLV
drm/i915: s/HAS_L3_GPU_CACHE/HAS_L3_DPF
drm/i915: Do remaps for all contexts
drm/i915: Keep a list of all contexts
drm/i915: Make l3 remapping use the ring
drm/i915: Add second slice l3 remapping
drm/i915: Fix HSW parity test
drm/i915: dump crtc timings from the pipe config
drm/i915: register backlight device also when backlight class is a module
drm/i915: write D_COMP using the mailbox
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
This regression has been introduced in
commit 9f11a9e4e5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jun 13 00:54:58 2013 +0200
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
Ville brough up the idea that this is just the pipe A quirk gone
wrong.
Note that after resume the bios might or might not have enabled pipe A
already. We have a bit of magic to make sure that on resume we set up
a decent mode for pipe A, but I fear if I just smash pipe A to always
on we'd enable it in a bogus state and hang the hw. Hence the
readback.
v2: Clarify the logic a bit as suggested by Chris. Also amend the
commit message to clarify why we don't unconditionally enable the
pipe.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66462
References: https://lkml.org/lkml/2013/8/26/238
Cc: Meelis Roos <mroos@ut.ee>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Use |= instead of = as suggested by Chris.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQMORAAoJEHm+PkMAQRiGj14H/1bjhtfNjPdX7MVQAzA+WpwX
s7h1IQu2Si9S5S1lBiM2sBTOssVcmfheO9x4yqm7JNOD1RnssWKOM3q+zVOLstwd
GD3gluJPeraD5EyYSqEJ9ILPQ3gbxb4wOlT0Z291TW6E8XhLRr0RTOJPksRsgvLH
Ckm9uJh6ArS6ZXfXiaDQfd+xHAQJkUfW6nMSA0g9ZO9C6KIDRvcbUmrY3m4HhfIk
mK0TXCBs+AXGDIjTEB8JgIQL/5y1Qn0c4R+2uTU/4YWwyLvJTV1e44kGoleukMMT
6Pw/TNlUEN161dbSaqCyF3sfXHDYQ5valycI2PDgitMtPSxbzsU1VDizS8+daRg=
=lEmF
-----END PGP SIGNATURE-----
Merge tag 'v3.12-rc2' into drm-intel-next
Backmerge Linux 3.12-rc2 to prep for a bunch of -next patches:
- Header cleanup in intel_drv.h, both changed in -fixes and my current
-next pile.
- Cursor handling cleanup for -next which depends upon the cursor
handling fix merged into -rc2.
All just trivial conflicts of the "changed adjacent lines" type:
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The init and resume codepaths want to handel the power well in slightly
different ways, so pull the power well init out from
intel_modeset_init_hw() which gets called in both cases.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure we write to IPS before we actually wait.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I always get royally confused how a modeline with all zeros could
possible pass the paranoid pipe config checker. Until I realize again
that we only check the crtc timings. So dump the crtc timings for the
adjusted mode.
This will be even more important for 3D support where the crtc timings
are markedly different from the input modeline if we have
frame-by-frame 3d output enabled.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
You can't write it using the MCHBAR mirror, the write will just get
dropped.
This should make us BSpec-compliant, but there's no real bug I could
reproduce that is fixed by this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Fix spelling mistake in the comment that Damien spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On HSW enabling a plane on a disabled pipe may hang the entire system.
And there's no good reason for doing it ever, so just don't.
v2: Move the crtc active checks to intel_crtc_cursor_{set,move} to
avoid confusing people during modeset
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor is disabled before crtc mode set in crtc disable (and we
assert this is the case), and enabled afterwards in crtc enable. Do not
update it in crtc mode set.
On HSW enabling a plane on a disabled pipe may hang the entire system.
And there's no good reason for doing it ever, so just don't.
v2: Add note about HSW hangs - vsyrjala
Cc: stable@vger.kernel.org
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Double wide mode is only available on pipe A, except on GDG where
pipe B is also double wide capable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pipe horizontal source size must be even when either LVDS dual channel
mode, DVO ganged mode, or pipe double wide mode is used.
We must round it down since we can never increase the user specified
viewport size.
The actual error from an odd pipe source width looks like a diagonal
shift, like you might get from a bad stride.
v2: s/ganaged/ganged/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't want to try to push the hardware beyond it's capabilities,
so check the pixel clock against the display core clock limit. Do
it for pre-gen4 for now since that's where we alread have the double
wide pixel clock limit check.
Let's assume that when double wide mode is enabled the max
pixel clock limit is also doubled.
FIXME: panel fitter downscaling probably affects the limit on
non-pch platforms too, so we'd need another version of
ilk_pipe_pixel_rate() to figure that out.
FIXME: should check the limits on all platforms. Also sprites
affect the max allowed pixel rate on some platforms, so we need
to eventually tie all the planes and pipes into one check in
the future. But we need plane state pre-compute before that can
happen.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read the double wide pipe information from hardware in
i9xx_get_pipe_config(), and check it in intel_pipe_config_compare()
For gen4+ double_wide is always false so the comparison can be done
on all platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine the need for double wide mode already in compute_config
stage as we need that information to figure out if horizontal
coordinates need to be adjusted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simply inline the 100MHz default we're using. Having gunk around that
has leftover LVDS support on a platform that just doesn't have this
isn't of any use.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First of all we should not be looking at fb->{width,height} as those do
not tell us what the actual pipe size is. Second of all we need to use
>= for the comparison.
So fix the comparison, and make use of the new pipe_src_{w,h} to
determine the real pipe source dimensions.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the cursor x coordinate is exactly -cursor_width, the cursor is
invisible. And obviously the same holds for the y coordinate and
cursor_height.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather that mess about with hdisplay/vdisplay from requested_mode, add
explicit pipe src size information to pipe config.
Now requested_mode is only really relevant for dvo/sdvo output timings.
For everything else either adjusted_mode or pipe src size should be
used.
In many places where we end up using pipe source size, we should
actually use the primary plane size, but we don't currently store
that information explicitly. As long as we treat primaries as full
screen only, we can get away with this. Eventually when we move
primaries over to drm_plane, we need to fix it all up.
v2: Add a comment to explain what pipe_src_{w,h} are
Add a note about primary planes to commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move intel_crtc_active() to intel_display.c and make it available
elsewhere as well.
intel_edp_psr_match_conditions() already has one open coded copy,
so replace that one with a call to intel_crtc_active().
v2: Copy paste a big comment from danvet's mail explaining
when we can ditch the extra checks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
lpt_program_iclkip() wants to know the pixel clock. It should get that
information from adjusted_mode, not crtc->mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i9xx_set_pipeconf() attempts to get the current pixel clock from
requested_mode. requested_mode.clock may be totally bogus, so the
clock should come from adjusted_mode.
v2: Dropped the intel_compute_config() hunk due to killing of the
INTEL_FDI_FREQ check
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check and dump for port_clock.
v2: Also dump port_clock
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new pipe config check macro PIPE_CONF_CHECK_CLOCK_FUZZY() to make
it trivial and error proof to compare clocks in a fuzzy manner.
v2: Drop extra curly braces
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().
Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.
In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.
DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.
v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
eliminate the useless link_freq variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the 120MHz refernce clock case for PCH DPLLs.
Also determine the reference clock frequency more accurately by
checking for the PLLB_REF_INPUT_SPREADSPECTRUMIN refclk input
mode. The gen2 code already checked it, but it stil assumed a
fixed 66MHz refclk. Instead we need to consult the VBT for the
real value.
v2: Fix refclk for SSC panel case
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already extract the DPLL state to pipe_config, so let's make use of
it in i9xx_crtc_clock_get() and avoid the register reads.
This will also make the function closer to being useable with PCH DPLL
since the registers for those live in a different address.
Also kill the useless adjusted_mode.clock zeroing. It's already zero at
this point.
v2: Read out DPLL state in intel_crtc_mode_get()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extract the code to calculate the dotclock from the link clock and M/N
values into a new function from ironlake_crtc_clock_get().
The new function can be used to calculate the dotclock for both FDI and
DP cases.
Also simplify the code a bit along the way.
v2: Don't forget about non-pch encoders in ironlake_crtc_clock_get()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor is supposed to be disabled during crtc mode set (disabled by
ctrc disable). Assert this is the case.
v2: move cursor disabled assert next to plane asserts (Ville)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to do fuzzy clock checks for other things besides
adjusted_mode.clock, so just pass two two clocks to compare
to intel_fuzzy_clock_check().
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add functions to read out the CPU and PCH transcoder M/N values,
and use them to fill out the pipe config dp_m_n information. And
while at it populate has_dp_encoder too.
Also refactor ironlake_get_fdi_m_n_config() to simply call the new
intel_cpu_transcoder_get_m_n() function.
v2: Remember the DDI
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CTG+ read out the pipe bpp setting from hardware and fill it into
pipe config. Also check it appropriately.
v2: Don't do the pipe_bpp extraction inside the PCH only code block on
ILK+.
Avoid the PIPECONF read as we already have read it for the
PIPECONF_EANBLE check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It would be easier if adjusted_mode.clock would be the pipe pixel clock,
and it actually is, except for the cases where pixel_multiplier > 1.
So let's change intel_sdvo to use port_clock as the multiplied clock,
and then we can leave adjusted_mode.clock as pipe pixel clock.
v2: Improve port_clock documentation
Rebased on top of SDVO pixel_multiplier fixes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We feed the non-multiplied clock to intel_link_compute_m_n(), so the
opposite operation should use the same order of operations. So we just
multiply by pixel_multiplier in the end now.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ignoring the legacy DRI1 code, and a couple of special cases (to be
discussed later), all access to the ring is mediated through requests.
The first write to a ring will grab a seqno and mark the ring as having
an outstanding_lazy_request. Either through explicitly adding a request
after an execbuffer or through an implicit wait (either by the CPU or by
a semaphore), that sequence of writes will be terminated with a request.
So we can ellide all the intervening writes to the tail register and
send the entire command stream to the GPU at once. This will reduce the
number of *serialising* writes to the tail register by a factor or 3-5
times (depending upon architecture and number of workarounds, context
switches, etc involved). This becomes even more noticeable when the
register write is overloaded with a number of debugging tools. The
astute reader will wonder if it is then possible to overflow the ring
with a single command. It is not. When we start a command sequence to
the ring, we check for available space and issue a wait in case we have
not. The ring wait will in this case be forced to flush the outstanding
register write and then poll the ACTHD for sufficient space to continue.
The exception to the rule where everything is inside a request are a few
initialisation cases where we may want to write GPU commands via the CS
before userspace wakes up and page flips.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the call to intel_update_watermarks() just once or twice during
modeset. Ideally it should happen independently when each plane gets
enabled/disabled, but for now it seems better to keep it in central
place. We can improve things when we get all the planes sorted out
in a better way.
When enabling set up the watermarks just before the pipe is enabled.
And when disabling we need to wait until we've marked the crtc as
inactive, as otherwise intel_crtc_active() would still think the pipe
is enabled and the computed watermarks would reflect that.
v2: Pimp up the commit message a bit
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Passing the appropriate crtc to intel_update_watermarks() should help
in avoiding needless work in the future.
v2: Avoid clash with internal 'crtc' variable in some wm functions
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace "%8x" with "%08x".
The hex number should be shown with zero stuffed instead of spaces.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Detangle the additional state of whether or not the hw has the pfit
enabled from whether it has zero size. This allows us to cleanly
distinguish in the code when we expect the pfit to be enabled (for
Haswell pc8), and when the BIOS is confused and needs sanitizing.
Reported-by: shui yanwei <yangweix.shui@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68251
Tested-by: shui yanwei <yangweix.shui@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When transitioning away from vgacon the system tries to save the
current contents of the VGA memory, so that it can be cleanly handed
off to fbcon (or whatever comes afterwards).
The recent change
commit 81b5c7bc8d
Author: Alex Williamson <alex.williamson@redhat.com>
Date: Wed Aug 28 09:39:08 2013 -0600
i915: Update VGA arbiter support for newer devices
caused i915 to disable VGA memory decode for the IGD when i915 is
initializing. Unfortunately that happens before the vgacon->fbcon
handoff so vgacon_save_screen() will read out all ones from the
VGA memory.
After the handoff fbcon will inherit the bogus state from vgacon,
and pre-fills the fb with matching contents. The end result is
a white rectangle in the top left corner of the screen, the size
of which matches the now inactive VGA console.
To remedy the situation delay the disabling of VGA memory until
the vgacon->fbcon handoff has happened.
Also rename i915_enable_vga to i915_enable_vga_mem to make
the relationship between these functions clearer.
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once again we find that Valleyview is ever so subtlety different from
the rest of its gen7 brethen. In this case, Valleyview has no support
for pageflipping from the RCS ring.
Fixes a regression from
commit ffe74d7550
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Aug 26 20:58:12 2013 +0100
drm/i915: Use RCS flips on Ivybridge+
Reported-by: "Lee, Chon Ming" <chon.ming.lee@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68968
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The patch doesn't contain functional change, but is to prepare for
future platform which has different DPIO phy. The additional pipe
parameter will use to select which phy to target for.
v2: Update the commit message and add static for the new function.
(Jani/Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ironlake_fdi_compute_config() already checks that we have enough
FDI bandwidth. And it doesn't just use a hardcoded value but takes
into account factors such as the actual FDI frequency, shared FDI
B/C lanes, etc.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For DP pll settings, there is only two golden configs. Instead of
running through the algorithm to determine it, hardcode the value and get it
determine in intel_dp_set_clock.
v2: Rework on the intel_limit compiler warning. (Jani)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Fix up checkpatch issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec says to notify prior to power down and after power up. It is
unclear whether it makes a difference.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DPLL is not needed for DSI
v2: Rebase due to added DSI PLL assertion patch.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For DSI, we need to be asserting DSI PLL, not DPLL.
This is a somewhat stopgap implementation. It's slightly ugly to have to
pass the dsi parameter to intel_enable_pipe().
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The dpll actually runs at the port clock so we don't need
to multiply it again with the pixel multiplier to get the
adjusted_mode.clock. This is in contrast to the ironlake
pixel clock readout code which uses the fdi dotclock: That
one does _not_ run with multiplied pixels.
This issue goes back to the original clock readout code added
in
commit f1f644dc66
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Jun 27 00:39:25 2013 +0300
drm/i915: get mode clock when reading the pipe config v9
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is intended to add VGA arbiter support for Intel HD graphics on
Core processors. The old GMCH registers no longer exist, so even
though it appears that i915 participates in VGA arbitration, it doesn't
work. On Intel HD graphics we already attempt to disable VGA regions
of the device. This makes registering as a VGA client unnecessary since
we don't intend to operate differently depending on how many VGA devices
are present. We can disable VGA memory regions by clearing the memory
enable bit in the VGA MSR. That only leaves VGA IO, which we update
the VGA arbiter to know that we don't participate in VGA memory
arbitration. We also add a hook on unload to re-enable memory and
reinstate VGA memory arbitration.
v3: Use explicit LEGACY_IO | LEGACY_MEM when restoring rather than
LEGACY_MASK, per Ville's comments.
v2: I915_READ/WRITE accessors don't work in i915_disable_vga, use inb/outb
directly. Also, on the driver unbind VGA enable path, acquire legacy
IO to re-enable VGA memory. Correct comment.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add patch changelog. Also squash in a fixup to have a dummy
static inline for vga_set_legacy_decoding for CONFIG_VGA_ARB=n as
reported by the 0-day kernel build bot.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
fixup 2
We shouldn't disable the trickle feed bits on Haswell. Our
documentation explicitly says the trickle feed bits of PRI_CTL and
CUR_CTL should not be programmed to 1, and the hardware engineer also
asked us to not program the SPR_CTL field to 1. Leaving the bits as 1
could cause underflows.
Reported-by: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RCS flips do work on Iybridge+ so long as we can unmask the messages
through DERRMR. However, there are quite a few workarounds mentioned
regarding unmasking more than one event or triggering more than one
message through DERRMR. Those workarounds in principle prevent us from
performing pipelined flips (and asynchronous flips across multiple
planes) and equally apply to the "known good" BCS ring. Given that it
already appears to work, and also appears to work with unmasking all 3
planes at once (and queuing flips across multiple planes), be brave.
Bugzlla: https://bugs.freedesktop.org/show_bug.cgi?id=67600
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Lightly-tested-by: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Need to get my stuff out the door ;-) Highlights:
- pc8+ support from Paulo
- more vma patches from Ben.
- Kconfig option to enable preliminary support by default (Josh
Triplett)
- Optimized cpu cache flush handling and support for write-through caching
of display planes on Iris (Chris)
- rc6 tuning from Stéphane Marchesin for more stability
- VECS seqno wrap/semaphores fix (Ben)
- a pile of smaller cleanups and improvements all over
Note that I've ditched Ben's execbuf vma conversion for 3.12 since not yet
ready. But there's still other vma conversion stuff in here.
* tag 'drm-intel-next-2013-08-23' of git://people.freedesktop.org/~danvet/drm-intel: (62 commits)
drm/i915: Print seqnos as unsigned in debugfs
drm/i915: Fix context size calculation on SNB/IVB/VLV
drm/i915: Use POSTING_READ in lcpll code
drm/i915: enable Package C8+ by default
drm/i915: add i915.pc8_timeout function
drm/i915: add i915_pc8_status debugfs file
drm/i915: allow package C8+ states on Haswell (disabled)
drm/i915: fix SDEIMR assertion when disabling LCPLL
drm/i915: grab force_wake when restoring LCPLL
drm/i915: drop WaMbcDriverBootEnable workaround
drm/i915: Cleaning up the relocate entry function
drm/i915: merge HSW and SNB PM irq handlers
drm/i915: fix how we mask PMIMR when adding work to the queue
drm/i915: don't queue PM events we won't process
drm/i915: don't disable/reenable IVB error interrupts when not needed
drm/i915: add dev_priv->pm_irq_mask
drm/i915: don't update GEN6_PMIMR when it's not needed
drm/i915: wrap GEN6_PMIMR changes
drm/i915: wrap GTIMR changes
drm/i915: add the FCLK case to intel_ddi_get_cdclk_freq
...
This lets drivers see the flags requested by the application
[airlied: fixup for rcar/imx/msm]
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
If we don't use the return value of a mmio read our coding style is to
use the POSTING_READ macro. This avoids cluttering the mmio traces.
While at it add the missing posting read in the lcpll enable function
that Paulo spotted.
v2: Drop the _NOTRACE changes, tracing such wait_for loops in the modeset
code might actually be rather useful!
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently only enter PC8+ after all its required conditions are
met, there's no rendering, and we stay like that for at least 5
seconds.
I chose "5 seconds" because this value is conservative and won't make
us enter/leave PC8+ thousands of times after the screen is off: some
desktop environments have applications that wake up and do rendering
every 1-3 seconds, even when the screen is off and the machine is
completely idle.
But when I was testing my PC8+ patches I set the default value to
100ms so I could use the bad-behaving desktop environments to
stress-test my patches. I also thought it would be a good idea to ask
our power management team to test different values, but I'm pretty
sure they would ask me for an easy way to change the timeout. So to
help these 2 cases I decided to create an option that would make it
easier to change the default value. I also expect people making
specific products that use our driver could try to find the perfect
timeout for them.
Anyway, fixing the bad-behaving applications will always lead to
better power savings than just changing the timeout value: you need to
stop waking the Kernel, not quickly put it back to sleep again after
you wake it for nothing. Bad sleep leads to bad mood!
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch allows PC8+ states on Haswell. These states can only be
reached when all the display outputs are disabled, and they allow some
more power savings.
The fact that the graphics device is allowing PC8+ doesn't mean that
the machine will actually enter PC8+: all the other devices also need
to allow PC8+.
For now this option is disabled by default. You need i915.allow_pc8=1
if you want it.
This patch adds a big comment inside i915_drv.h explaining how it
works and how it tracks things. Read it.
v2: (this is not really v2, many previous versions were already sent,
but they had different names)
- Use the new functions to enable/disable GTIMR and GEN6_PMIMR
- Rename almost all variables and functions to names suggested by
Chris
- More WARNs on the IRQ handling code
- Also disable PC8 when there's GPU work to do (thanks to Ben for
the help on this), so apps can run caster
- Enable PC8 on a delayed work function that is delayed for 5
seconds. This makes sure we only enable PC8+ if we're really
idle
- Make sure we're not in PC8+ when suspending
v3: - WARN if IRQs are disabled on __wait_seqno
- Replace some DRM_ERRORs with WARNs
- Fix calls to restore GT and PM interrupts
- Use intel_mark_busy instead of intel_ring_advance to disable PC8
v4: - Use the force_wake, Luke!
v5: - Remove the "IIR is not zero" WARNs
- Move the force_wake chunk to its own patch
- Only restore what's missing from RC6, not everything
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was causing WARNs in one machine, so instead of trying to guess
exactly which hotplug bits should exist, just do the test on the
non-HPD bits. We don't care about the state of the hotplug bits, we
just care about the others, that need to be 1.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If LCPLL is disabled, there's a chance we might be in package C8 state
or deeper, and we'll get a hard hang when restoring LCPLL (also, a red
led lights up on my motherboard). So grab the force_wake, which will
get us out of RC6 and, as a consequence, out of PC8+ (since we need
RC6 to get into PC8+).
Note: Discussions with hw designers are still ongoing what exactly
goes boom here. But I think we can go ahead and just merge this little
hack for now until it's clear what we actually need.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add small note about the current state of the discussion
around this hack.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The existing code was trying different vswing and preemphasis settings
in the wrong place, and wasn't trying them enough. So add a loop to
walk through them, properly disabling FDI TX and RX in between if a
failure is detected.
v2: remove unneeded reg writes, add delays around bit lock checks (Jesse)
v3: fix TX and RX disable per spec (Paulo)
fix delays per spec (Paulo)
make RX symbol lock check match TX bit lock check (Paulo)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51983
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whenever I need to work with the HSW_PWER_WELL_* register bits I have
to look at the documentation to find out which bit is to request the
power well and which one shows its current state. Rename the bits so I
won't need to look the docs every time.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the power well is disabled VGA is guaranteed to be disabled.
This fixes unclaimed register messages that happen on suspend/resume.
v2: Check the actual hw power well state instead of our own tracking
to make sure VGA is _really_ off (in case the BIOS/KVMr has just its
own request bit set). Requested by Ville.
Note: Ville suggested whether it wouldn't be better to just enable the
power well over a slightly longer time in our resume code, since we
already do that. I tend to agree, but there's also the modeset force
code in the lid notifier which _also_ eventually calls redisable_vga.
We shouldn't ever need this on somewhat modern hw (everything with
opregion essentially) but the code to bail out isn't there. Hence
stick with this simple approach here for now.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67517
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Summarize the discussion around the resume sequence and lid
notifier a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After computing the stage changes for the set_config, record those in
the debug log.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Caught by "make W=1 drivers/gpu/drm/i915/".
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we get an error event really early in the driver setup sequence,
which gen3 is especially prone to with various display GTT faults we
Oops. So try to avoid this.
Additionally with Haswell the transcoders are a separate bank of
registers from the pipes (4 transcoders, 3 pipes). In event of an
error, we want to be sure we have a complete and accurate picture of
the machine state, so record all the transcoders in addition to all
the active pipes.
This regression has been introduced in
commit 702e7a56af
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Oct 23 18:29:59 2012 -0200
drm/i915: convert PIPECONF to use transcoder instead of pipe
Based on the patch "drm/i915: Dump all transcoder registers on error"
from Chris Wilson:
v2: Rebase so that we don't try to be clever and try to figure out the
cpu transcoder from hw state. That exercise should be done when we
analyze the error state offline.
The actual bugfix is to not call intel_pipe_to_cpu_transcoder in the
error state capture code in case the pipes aren't fully set up yet.
v3: Simplifiy the err->num_transcoders computation a bit. While at it
make the error capture stuff save on systems without a display block.
v4: Fix fail, spotted by Jani.
v5: Completely new commit message, cc: stable.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60021
Cc: stable@vger.kernel.org
Tested-by: Dustin King <daking@rescomp.stanford.edu>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The display engine has unique coherency rules such that it requires
special handling to ensure that all writes to cursors, scanouts and
sprites are clflushed. This patch introduces the infrastructure to
simply track when an object is being accessed by the display engine.
v2: Explain the is_pin_display() magic as the sources for obj->pin_count
and their individual rules is not obvious. (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ryan noticed that on his board, HDMI was wired up to port C but not
exposed by the kernel, which had only expected DP on that port. Fix
that up by enumerating both ports if possible.
Tested-by: "Matsumura, Ryan" <ryan.matsumura@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fix up the whitespace fail. Tsk.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And also fix a small typo in the intel_encoder_dpms() comment.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The SDVO code tries to compare the encoder's and crtc's idea of the
pixel_multiplier. Normally they have to match, but when transitioning
to DPMS off, we turn off the pipe before reading out the pipe_config,
so the pixel_multiplier in the pipe_config will be 0, whereas the
encoder will still have its pixel_multiplier set to whatever value we
were using when the display was active. This leads to a warning
from intel_modeset_check_state().
WARNING: CPU: 1 PID: 2846 at drivers/gpu/drm/i915/intel_sdvo.c:1378 intel_sdvo_get_config+0x158/0x160()
SDVO pixel multiplier mismatch, port: 0, encoder: 1
Modules linked in: snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_hwdep
CPU: 1 PID: 2846 Comm: Xorg Not tainted 3.11.0-rc3-00208-gbe1e8d7-dirty #19
Hardware name: Apple Computer, Inc. Macmini1,1/Mac-F4208EC8, BIOS MM11.88Z.0055.B03.0604071521 04/07/06
00000000 00000000 ef0afa54 c1597bbb c1737ea4 ef0afa84 c10392ca c1737e6c
ef0afab0 00000b1e c1737ea4 00000562 c12dfbe8 c12dfbe8 ef0afb14 00000000
f697ec00 ef0afa9c c103936e 00000009 ef0afa94 c1737e6c ef0afab0 ef0afadc
Call Trace:
[<c1597bbb>] dump_stack+0x41/0x56
[<c10392ca>] warn_slowpath_common+0x7a/0xa0
[<c103936e>] warn_slowpath_fmt+0x2e/0x30
[<c12dfbe8>] intel_sdvo_get_config+0x158/0x160
[<c12c3220>] check_crtc_state+0x1e0/0xb10
[<c12cdc7d>] intel_modeset_check_state+0x29d/0x7c0
[<c12dfe5c>] intel_sdvo_dpms+0x5c/0xa0
[<c12985de>] drm_mode_obj_set_property_ioctl+0x40e/0x420
[<c1298625>] drm_mode_connector_property_set_ioctl+0x35/0x40
[<c1289294>] drm_ioctl+0x3e4/0x540
[<c10fc1a2>] do_vfs_ioctl+0x72/0x570
[<c10fc72f>] SyS_ioctl+0x8f/0xa0
[<c159b7fa>] sysenter_do_call+0x12/0x22
---[ end trace 7ce940aff1366d60 ]---
Fix the problem by skipping the encoder get_config() function for
inactive encoders.
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than open-code the teardown of a framebuffer, export the routine
from intel_display.c. This then make intel_fbdev symmetric in its use of
the common intel_framebuffer routines to initialise and clean up the
struct intel_framebuffer. (And new features need only be added in one
location!)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Userspace can pass a mode with an unspecified vsync/hsync polarity
setting. All encoders in the Intel driver take this to mean a negative
polarity setting. The HW readout/state checker code on the other hand
needs these flags to be explicitly set, otherwise the state checker will
WARN about the mismatch.
Get rid of the WARN by making the polarity setting explicit in the
adjusted mode flags based on the requested mode flags. This will keep
the existing behavior otherwise.
Note that we could guess from the other timing parameters whether the
user wanted a VESA or other standard mode and set the polarity
accordingly. This is what the NV driver does
(drivers/gpu/drm/nouveau/dispnv04/crtc.c), but I think that's not very
exact and would change the existing behavior of the Intel driver.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65442
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: cancan,feng <cancan.feng@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV wants encoder enabling before the pipe is up. With the previously
rearranged VLV DP and HDMI ->pre_enable and ->enable callbacks in place,
this no longer depends on the early ->enable hook call. Move the
->enable call at the end of the sequence, similar to the crtc enable on
other platforms. This will be needed e.g. for moving the eDP backlight
enabling to the right place in the sequence, currently done too early on
VLV.
There should be no functional changes.
v2: Rebase.
v3: Explain why this is needed in the commit message (Chris).
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we get flooded by the kernel warning us that we are doing
long sequences of IO without serialisation. For example,
WARNING: CPU: 0 PID: 11136 at drivers/gpu/drm/i915/intel_sideband.c:40 vlv_sideband_rw+0x48/0x1ef()
Modules linked in:
CPU: 0 PID: 11136 Comm: kworker/u2:0 Tainted: G W 3.11.0-rc2+ #4
Call Trace:
[<c2028564>] ? warn_slowpath_common+0x63/0x78
[<c227ad43>] ? vlv_sideband_rw+0x48/0x1ef
[<c20285dd>] ? warn_slowpath_null+0xf/0x13
[<c227ad43>] ? vlv_sideband_rw+0x48/0x1ef
[<c227b060>] ? vlv_dpio_write+0x1c/0x21
[<c2262b3b>] ? intel_dp_set_signal_levels+0x24a/0x385
[<c2264909>] ? intel_dp_complete_link_train+0x25/0x1d1
[<c2264c55>] ? intel_dp_check_link_status+0xf7/0x106
[<c2238ced>] ? i915_hotplug_work_func+0x17b/0x221
[<c203a204>] ? process_one_work+0x12e/0x210
[<c203a5e4>] ? worker_thread+0x116/0x1ad
[<c203a4ce>] ? rescuer_thread+0x1cb/0x1cb
[<c203d8f5>] ? kthread+0x67/0x6c
[<c2457ebb>] ? ret_from_kernel_thread+0x1b/0x30
[<c203d88e>] ? init_completion+0x18/0x18
v2: Retire the locking in vlv_crtc_enable() and do it close to the meat.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Squash in a s/mutex_lock/mutex_unlock/ fixup spotted by the 0
day kernel build/coccinelle and reported by Dan Carpenter.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Art confirms that this should work fine. Since most panels are 18bpp
with dithering from 24bpp, the existing code wouldn't be enabled in most
cases.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the old days of the crtc helpers we've only had the encoder and
crtc ->mode_fixup callbacks. So when the lvds connector wanted to
adjust the crtc timings it had to set a driver-private mode flag to
tell the crtc mode fixup code to not overwrite them with the generic
ones.
When converting things to the new infrastructure I've kept the entire
logic and only moved the flag to pipe_config->timings_set. But this
logic is pretty tricky and already caused regressions:
commit 21d8a4756a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 12 08:07:30 2013 +0200
drm/i915: fix pfit regression for non-autoscaled resolutions
So take advantage of the flexibility our own modeset infrastructure
affords us and prefill default crtc timings. This allows us to rip out
->timings_set. Note that we overwrite things again when retrying the
pipe config computation due to bandwidth constraints to avoid bogus
crtc timings if the encoder only does relative adjustments (which is
how the pfit code works). Only a theoretical concern though since
platforms where we retry (pch-split platforms) do not need
adjustements (since only the old gmch pfit needs that). But let's
better be safe than sorry.
Since we now initialize the crtc timings before calling the
encoder->compute_config functions the crtc initialization in the gmch
pfit code is now redudant and so can be removed.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add a paragraph to the commit message to explain why we can
ditch the crtc timings initialization call from the gmch pfit code, to
answer a question from Rodrigo's review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The encoder->mode_set callback from the crtc helpers is now completely
unused in our driver. Good riddance!
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Everyone is now using our own ->compute_config callback, which means
we can now also make that callback mandatory.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need the correct clock to accurately assess whether we need to
enable the double wide pipe mode or not.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Stuart Abercrombie <sabercrombie@google.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, the register access code is split between i915_drv.c and
intel_pm.c. It only bares a superficial resemblance to the reset of the
powermanagement code, so move it all into its own file. This is to ease
further patches to enforce serialised register access.
v2: Scan for random abuse of I915_WRITE_NOTRACE
v3: Take the opportunity to rename the GT functions as uncore. Uncore is
the term used by the hardware design (and bspec) for all functions
outside of the GPU (and CPU) cores in what is also known as the System
Agent.
v4: Rebase onto SNB rc6 fixes
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Wrestle patch into applying and inline
intel_uncore_early_sanitize (plus move the old comment to the new
function). Also keep the _santize postfix for intel_uncore_sanitize.]
[danvet: Squash in fixup spotted by Chris on irc: We need to call
intel_pm_init before intel_uncore_sanitize since the later will call
cancel_work on the delayed rps setup work the former initializes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This backmerges Linus' merge commit of the latest drm-fixes pull:
commit 549f3a1218
Merge: 42577ca058ca4a
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue Jul 23 15:47:08 2013 -0700
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
We've accrued a few too many conflicts, but the real reason is that I
want to merge the 100% solution for Haswell concurrent registers
writes into drm-intel-next. But that depends upon the 90% bandaid
merged into -fixes:
commit a7cd1b8fea
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 19 20:36:51 2013 +0100
drm/i915: Serialize almost all register access
Also, we can roll up on accrued conflicts.
Usually I'd backmerge a tagged -rc, but I want to get this done before
heading off to vacations next week ;-)
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem.c
v2: For added hilarity we have a init sequence conflict around the
gt_lock, so need to move that one, too. Spotted by Jani Nikula.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now there are no callers, but these functions are going to be
needed for the code that allows Package C8+. Other future features may
also require this code.
Also merge the commit which introduced assert_can_disable_lcpll and
had the following commit message:
Most of the hardware needs to be disabled before LCPLL is disabled, so
let's add a function to assert some of items listed in the "Display
Sequences for LCPLL disabling" documentation.
The idea is that hsw_disable_lcpll should not disable the hardware,
the callers need to take care of calling hsw_disable_lcpll only once
everything is already disabled.
v2: - Rebase.
- Fix D_COMP wait timeout.
v3: - Use wait_for_atomic_use (Ben)
- Remove/add a useless/needed POSTING_READ (Ben)
- Early return in case LCPLL is already restored (Ben)
- Add ndelay(100) (Ben)
v4: - Merge the commit that added assert_can_disable_lcpll (Ben)
- Add interrupt assertions (Ben)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail since there's no HAS_LP_PCH yet.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently don't support HDMI clock bending nor use SSC for DP or
HDMI on Haswell, so the only case where we need CLKOUT_DP is for VGA.
v2: - Replace the IS_ULT check for LPT-LP
- Simplify GEN0/DBUFF0 check due to change on the previous patch
- Also check for SBI_SSCCTL_DISABLE (Ben).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now it implements 3 different sequences from BSpec and also has
support for ULT.
v2: - Change IS_ULT checks for LPT-LP checks
- Add check for LPT-LP + with_fdi (Ben)
- Merge DBUFF0/GEN0 bit definitions since they're the same
register (Ben)
- DBUFF0 (1<<0) is Disable, not Enable
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=47941
BugLink: https://bugs.launchpad.net/bugs/1163720
BugLink: https://bugs.launchpad.net/bugs/1162026
Some machines suffer from non-functional backlight controls if
BLM_PCH_PWM_ENABLE is set, so provide a quirk to avoid doing so.
Apply this quirk to Dell XPS 13 models.
Tested-by: Eric Griffith <EGriffith92@gmail.com>
Tested-by: Kent Baxley <kent.baxley@canonical.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The next step is to modify lpt_enable_clkout_dp to enable support for
"Sequence to enable CLKOUT_DP" and "Sequence to enable CLKOUT_DP
without spread".
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because lpt_init_pch_refclk implements the "Sequence to enable
CLKOUT_DP for FDI usage and configure PCH FDI I/O", which is very
similar to "Sequence to enable CLKOUT_DP" and "Sequence to enable
CLKOUT_DP without spread". With the extracted functions we can more
easily implement the two missing sequences.
v2: Rebase (WaMPhyProgramming:hsw comment).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The machines that fall in the "is_sdv" case are some very early
pre-production steppings. This patch may break VGA output after
suspend/resume on these machines.
Even the documentation for the is_sdv cases was removed from BSpec.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PSR must be enabled after transcoder and port are running.
And it is only available for HSW.
v2: move enable/disable to intel_ddi
v3: The spec suggests PSR should be disabled even before backlight (by pzanoni)
v4: also disabling and enabling whenever panel is disabled/enabled.
v5: make it last patch to avoid breaking whenever bisecting. So calling for
update and force exit came to this patch along with enable/disable calls.
v6: Remove unused and unecessary psr_enable/disable calls, as notice by Paulo.
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Drop the psr exit code in the busy ioctl since I didn't merge
that part of the infrastructure yet - it needs more thought.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit e3de42b684
Author: Imre Deak <imre.deak@intel.com>
Date: Fri May 3 19:44:07 2013 +0200
drm/i915: force full modeset if the connector is in DPMS OFF mode
a new function was added that walked over the set of connectors to see
if any of the currently associated CRTC was switched off. This function
walked an array of connectors, rather than the array of pointers to
connectors contained in the drm_mode_set - i.e. it was dereferencing far
past the end of the first connector. This only becomes an issue if we
attempt to use a clone mode (i.e. more than one connector per CRTC) such
that set->num_connectors > 1.
Reported-by: Timo Aaltonen <tjaalton@ubuntu.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65927
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Egbert Eich <eich@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There seems to be no limit to the amount of gunk the firmware can
leave behind. Some platforms leave pch dplls on which are not in
active use at all. The example in the bug report is a Apple Macbook
Pro.
Note that this escape scrunity of the hw state checker until we've
tried to use this enabled, but unused pll since we did only check for
the inverse case of a in-used, but disabled pll.
v2: Add a WARN in the pll state checker which would have caught this
case.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66952
Reported-and-tested-by: shui yangwei <yangweix.shui@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Toghether with the hw state readout this should catch cases where we
don't properly updated the pll state (either in sw or hw). At least
for the shared dpll code the equivalent tricke helped a lot in
catching bugs.
Also rename the function prefix, it's not a generic piece of
infrastructure.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec for the "DPLL HDMI multiplier" field says:
"Restriction : The DPLL must be enabled and stable before setting these bits.
These bits must be programmed after DPLL_SEL is programmed."
There is apparently no restriction on programming the DPLL_SEL
register wrt the DPLL. So let's just move that up before we enable the
pch dpll.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to call the ->pre_pll_enable hook twice if we don't enable the
dpll too early. This should make Jani a bit less grumpy.
v2: Rebase on top of the newly-colored BUG_ONs.
v3: Reinstate the lost write of the DPLL_MD register, spotted by Imre.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move error state generation and stringification to it's
own compilation unit. Sysfs also uses this so it can't be
under CONFIG_DEBUG_FS
This fixes a regression introduced in
commit ef86ddced7
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu Jun 6 17:38:54 2013 +0300
drm/i915: add error_state sysfs entry
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66814
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Came accross two open coding of for_each_pipe(), might as well use the
macro.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's in the PFIT_CONTROL register, but very much associated with the
lvds encoder. So move the readout for it (in the case of an otherwise
disabled pfit) from the pipe to the lvds encoder's get_config
function.
Otherwise we get a pipe state mismatch if we use pipe B for a non-lvds
output and we've left the dither bit enabled behind us. This can
happen if the BIOS has set the bit (some seem to unconditionally do
that, even in the complete absence of an lvds port), but not enabled
pipe B at boot-up. Then we won't clear the pfit control register since
we can only touch that if the pfit is associated with our pipe in the
crtc configuration - we could trample over the pfit state of the other
pipe otherwise since it's shared. Once pipe B is enabled we notice
that the 6to8 dither bit is set and complain about the mismatch.
Note that testing indicates that we don't actually need to set this
bit when the pfit is disabled, dithering on 18bpp panels seems to work
regardless. But ripping that code out is not something for a bugfix
meant for -rc kernels.
v2: While at it clarify the logic in i9xx_get_pfit_config, spurred by
comments from Chris on irc.
v3: Use Chris suggestion to make the control flow in
i9xx_get_pfit_config easier to understand.
v4: Kill the extra line, spotted by Chris.
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
References: http://lists.freedesktop.org/archives/intel-gfx/2013-July/030092.html
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I just got confirmation that we're using some old values for the PLL
LPF coefficients for DP RBR/HDMI/DAC on VLV. The
VLV2A0_DP_eDP_HDMI_DPIO_driver_vbios_notes_9 document lists both values
by mistake, and apparently we had picked the wrong one. Change the
coefficients to the recommended values.
Changing the value doesn't appear to destabilize the VGA output picture
even with my sensitive HP ZR24w display. Also HDMI output to my TV still
works fine.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Section 1.5.4, "DPLL A Control Register" from Bspec about bit 23
"FPA0/A1 P2 Clock Divide":
0 = Divide by 2
1 = Divide by 4. This bit must be set in DVO non-gang mode
So copy the current limits (which should be good for i8xx) and create
a new set for dvo encoders.
Reviewed-by: Chris Wilson <chris@chris-wilson.oc.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've missed that intel_dvo_mode_set changes the dpll configuration.
Hence when I've reworked the sequence to only enable the dpll in the
crtc_enable callback in
commit 66e3d5c099
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jun 16 21:24:16 2013 +0200
drm/i915: move i9xx dpll enabling into crtc enable function
that special DVO bit was lost. Some BSpec reading confirms that it's
only needed for DVO encoders. Section 1.5.4, "DPLL A Control Register"
for bit 30:
"2X Clock Enable. When driving In non-gang DVO modes such as a
connected flat panel or TV, a 2X" version of the clock is needed. When
not using the 2X output it should be disabled. This bit cannot be set
when driving the integrated LVDS port on devices such as Montara-GM."
Fix this regression up.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66516
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Partially-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Soon we want to gut a lot of our existing assumptions how many address
spaces an object can live in, and in doing so, embed the drm_mm_node in
the object (and later the VMA).
It's possible in the future we'll want to add more getter/setter
methods, but for now this is enough to enable the VMAs.
v2: Reworked commit message (Ben)
Added comments to the main functions (Ben)
sed -i "s/i915_gem_obj_set_color/i915_gem_obj_ggtt_set_color/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_bound/i915_gem_obj_ggtt_bound/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_size/i915_gem_obj_ggtt_size/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_offset/i915_gem_obj_ggtt_offset/" drivers/gpu/drm/i915/*.[ch]
(Daniel)
v3: Rebased on new reserve_node patch
Changed DRM_DEBUG_KMS to actually work (will need fixing later)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only do this on IBX where there's a fixed pch dpll to pipe
assignment. Being explicit about it can't really hurt and makes
sparse happy.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
