A single object may be referenced by multiple registers fundamentally
breaking the static allotment of ids in the current design. When the
object is used the second time, the physical address of the first
assignment is relinquished and a second one granted. However, the
hardware is still reading (and possibly writing) to the old physical
address now returned to the system. Eventually hilarity will ensue, but
in the short term, it just means that cursors are broken when using more
than one pipe.
v2: Fix up leak of pci handle when handling an error during attachment,
and avoid a double kmap/kunmap. (Ville)
Rebase against -fixes.
v3: And fix the error handling added in v2 (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77351
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the upcoming patches we plan to break the correlation between
engine command streamers (a.k.a. rings) and ringbuffers, so it
makes sense to refactor the code and make the change obvious.
No functional changes.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen2 the scanline counter behaves a bit differently from the
later generations. Instead of adding one to the raw scanline
counter value, we must subtract one.
On HSW/BDW the scanline counter requires a +2 adjustment on HDMI
outputs. DP outputs on the on the other require the typical +1
adjustment.
As the fixup we must apply to the hardware scanline counter
depends on several factors, compute the desired offset at modeset
time and tuck it away for when it's needed.
v2: Clarify HSW+ situation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78997
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have to write to the primary plane base address registrer when we
enable/disable the primary plane in response to sprite coverage. Those
writes will cause the flip counter to increment which could interfere
with the detection of CS flip completion. We could end up completing
CS flips before the CS has even executed the commands from the ring.
To avoid such issues, wait for CS flips to finish before we toggle the
primary plane on/off.
v2: Rebased due to atomic sprite update changes
Testcase: igt/kms_mmio_vs_cs_flip/setplane_vs_cs_flip
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen2 reports FIFO underruns whenever no planes are enabled on the pipe.
So in order to avoid false positives we must enable the FIFO underrun
reporting only when at least one plane is enabled on the pipe. For
now just move the underrun reporting enable/disable points to the
other side of the plane enable/disable point. That doesn't cover cases
when we turn off all the planes for the pipe but leave the pipe running
on purpose, but it's better than the current situation.
On gen4+ we can actually move the underrun reporting enable/disable to
the opposite ends of the crtc enable/disable hooks. I suppose in theory
we could leave the underrun reporting enabled all the time, except on
VLV where PIPESTAT stops working when the display power well is down.
If we ever get around to unifying the PIPESTAT irq handling for all
gmch platforms, we should still follow the VLV route for other platforms.
It would also micro-optimize the irq handler a bit since we could then
skip the PIPESTAT reads for all disabled pipes.
Gen3 is still a mystery, but for now I'm going to assume it behaves
like gen4+.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIFO underruns don't generate interrupts on gmch platforms, so
if we want to know whether a modeset triggered FIFO underruns we
need to explicitly check for them.
As a modeset on one pipe could cause underruns on other pipes,
check for underruns on all pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
[danvet: Fix up merge error, kudos to Ville for noticing it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a pipe is already active when we init/resume there might not be a
full modeset afterwards so drm_vblank_on() may not get called. In such
a case if someone is holding a vblank reference across a suspend/resume
cycle drm_vblank_get() called after resuming won't re-enable the vblank
interrupts.
So in order to make sure vblank interrupts get re-enabled post-resume,
call drm_vblank_on() in intel_sanitize_crtc() if the crtc is already
active.
v2: Also drm_vblank_off() if the pipe got disabled magically
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Testecase: igt/kms_flip/vblank-vs-suspend
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in the drm vblank rework from Ville and me. drm core parts acked
by Dave Airlie
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Just a bit of fun around the placement of drm_vblank_on. This merge
resolution has been tested in drm-intel-nightly for a while already.
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't have hardware based disable bits on gmch platforms, so need
to block spurious underrun reports in software. Which means that we
_must_ start out with fifo underrun reporting disabled everywhere.
This is in big contrast to ilk/hsw/cpt where there's only _one_
disable bit for all platforms and hence we must allow underrun
reporting on disabled pipes. Otherwise nothing really works,
especially the CRC support since that's key'ed off the same irq
disable bit.
This allows us to ditch the fifo underrun reporting hack from the vlv
runtime pm code and unexport the internal function from i915_irq.c
again. Yay!
v2: Keep the display irq disabling, spotted by Imre.
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only the low-level irq handling functions still use integer crtc
indices with this. But fixing that will require a lot more sugery
and some good ideas for backwards compat with old ums userspace.
Both in drivers and in the drm core.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Originally these functions have been for user modesetting drivers to
ensure vblank processing doesn't fall over completely around modeset
changes. This has been carried over ever since then.
Now that Ville cleaned our vblank handling with an explicit
drm_vblank_off/on braket when disabling/enabling crtcs. So this seems
to be unnecessary now. The most important side effect was that due to
the delayed vblank disabling we have been pretty much guaranteed to
receive a vblank interrupt soonish after a crtc was enabled.
Note that our vblank handling across modeset is still fairly decent
fubar - we don't actually handle vblank counter all to well.
drm_update_vblank_count will make sure that the frame counter always
rolls forward, but userspace isn't really all to ready to cope with
the big jumps this causes.
This isn't a big mostly because the hardware retains the frame
counter. But with runtime pm and also across suspend/resume we fall
over.
Fixing this is a lot more involved and also needs som i-g-ts. So
material for another patch series.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All of the .queue_flip() callbacks duplicate the same code to pin the
buffers and calculate the gtt_offset. Move that code to
intel_crtc_page_flip(). In order to do that we must also move the ring
selection logic there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we've plugged the mmio vs. ring flip race, we shouldn't need
these vblank waits in the modeset codepaths anymore. So get rid of
them.
v2: gen2 needs to wait for planes to turn off before disabling pipe
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the vblank wait is gone from intel_enable_primary_plane(),
hsw_enable_ips() needs to do the vblank wait itself.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting from ILK, mmio flips also cause a flip done interrupt to be
signalled. This means if we first do a set_base and follow it
immediately with the CS flip, we might mistake the flip done interrupt
caused by the set_base as the flip done interrupt caused by the CS
flip.
The hardware has a flip counter which increments every time a mmio or
CS flip is issued. It basically counts the number of DSPSURF register
writes. This means we can sample the counter before we put the CS
flip into the ring, and then when we get a flip done interrupt we can
check whether the CS flip has actually performed the surface address
update, or if the interrupt was caused by a previous but yet
unfinished mmio flip.
Even with the flip counter we still have a race condition of the CS flip
base address update happens after the mmio flip done interrupt was
raised but not yet processed by the driver. When the interrupt is
eventually processed, the flip counter will already indicate that the
CS flip has been executed, but it would not actually complete until the
next start of vblank. We can use the DSPSURFLIVE register to check
whether the hardware is actually scanning out of the buffer we expect,
or if we managed hit this race window.
This covers all the cases where the CS flip actually changes the base
address. If the base address remains unchanged, we might still complete
the CS flip before it has actually completed. But since the address
didn't change anyway, the premature flip completion can't result in
userspace overwriting data that's still being scanned out.
CTG already has the flip counter and DSPSURFLIVE registers, and
although the flip done interrupt is still limited to CS flips alone,
the code now also checks the flip counter on CTG as well.
v2: s/dspsurf/gtt_offset/ (Chris)
Testcase: igt/kms_mmio_vs_cs_flip/setcrtc_vs_cs_flip
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73027
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add g4x_ prefix to flip_count_after_eq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_vblank_off() will turn off vblank interrupts, but as long as the
refcount is elevated drm_vblank_get() will not re-enable them. This
is a problem is someone is holding a vblank reference while a modeset is
happening, and the driver requires vblank interrupt to work during that
time.
Add drm_vblank_on() as a counterpart to drm_vblank_off() which will
re-enabled vblank interrupts if the refcount is already elevated. This
will allow drivers to choose the specific places in the modeset sequence
at which vblank interrupts get disabled and enabled.
Testcase: igt/kms_flip/*-vs-suspend
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add Testcase tag for the igt I've written.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Seems like we shouldn't leave the data lane resert deasserted when
the port if disabled. So propagate the reset the data lanes in
the encoder .post_disable() hook.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During the enable sequence we first enable the dclkp output to the
display controller, and then enable the PLL. Do the opposite during
the disable sequence.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to pick the correct data lanes based on the port not the
pipe, so move the data lane deassert into the encoder .pre_enable()
hook from the chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Setup the pipe config dpll state correctly for CHV. Also add
a assert_pipe_disabled() to chv_disable_pll(), and program the
DPLL_MD registers in chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unsurprisingly the cursor C regiters are also at a weird offset on CHV.
Add more pipe offsets to handle them.
This also gets rid of most of the differences between the i9xx vs. ivb
cursor code. We can unify the remaining code as well, but I'll leave
that for another patch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Besides the fairly useless BUG_ON the logic is completely generic
and cane be used on any platform what wants to reuse the shared
dpll support code.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the last piece of code which write state to the hardware in
the ironalake ->crtc_mode_set callback.
I think we could merge this with the pll->enable hook, but otoh the
ordering requirements with the ldvs port are really tricky. Doing the
FP0/1 writes up-front before we even prepare the lvds port (in the
pre_pll_enable hook) like on i9xx seems safest.
With this ilk+ platforms are now ready for runtime PM with DPMS. Since
hsw/bdw also support runtime pm besides snb we need to first make the
haswell code save before we can touch the core code.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of every time it isn't active: We only need to do that when
the pll is currently unused, i.e. when pll->refcount == 0. For
paranoia add a warning for the ibx case where plls have a fixed
mapping and hence should always be unused after the call to
intel_put_shared_dpll.
v2: Simplify control flow and use struct assignment instead of memcpy
as suggested by Damien.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this all hw writes are also gone from the ->crtc_mode_set hook on
vlv. I wondered whether we should track more of the pll state in the
pipe config, but otoh as long as we don't have shared plls that's not
really useful - the cross-checking of the port clock should be
sufficient.
While at it also de-magic some of the pipe checks, this has been
irking me since a long time.
Whit this vlv is now ready for runtime PM on dpms. If we'd have
runtime PM support in general ...
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These two writes are the very last hw writes from the
->crtc_modeset_callback on pre-gen5 hardware. As usual vlv is a bit
different, so this here is just warm-up.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again the same story: This code just transform sw state from the pipe
config into hardware state. And again we can't move the pll code, but
this time around because the state isn't properly tracked in the pipe
config.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again this code just transforms sw state from the pipe config into
hardware state, so we can just move it around. Unfortunately again a
few forward declarations since intel_display.c is becoming a bit of a
mess.
Note that both for i9xx and ironlake code the only things remaining in
the ->crtc_mode_set hook is now the clock state computation and
sharing code. That needs to be moved into the compute config stage so
that we can catch impossible configurations earlier.
Also note that some of the DPLL hw setup code is still run from within
->crtc_mode_set, namele the pll->mode_set callback. We need to move
that first before we can do fancy things like enable runtime PM for
dpms off.
v2: Make it compile again after the rebase, bisectability issue
reported by Wu Fengguang.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now this really should be in the pipe config somewhere, but till now
it isn't. We can at least move it up a bit next to all the other pll
code since intel_dp_set_m_n really doesn't depend upon this.
This is just prep work so that moving all the hw frobbing code from
->crtc_mode_set to ->crtc_enable is clean.
v2: Do the same for haswell while at it, not just for ivb.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All these functions simply convert sw state as encoded in the pipe
config or primary framebuffer into hardware state. So we can move them
all into the crtc enable hook. Unfortunately this means a little bit
of duplication between the i9xx and vlv functions, but since we
already have highly refactored code I think this is acceptable.
Also a pile of forward declarations unfortunately.
Note also that the various <platform>_update_pll functions are still
called from within the ->crtc_mode_set hook. Mostly they compute the
clock state for the pipe config, but unfortunately there are some
random register writes interspersed. Those need to be moved out first
before we can enable runtime PM for DPMS.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can apperently miss them, but breaking the entire driver hampers
testing. So bail out after one minute, our customerary "this is a lost
cause" timeout.
References: https://bugs.freedesktop.org/show_bug.cgi?id=78383
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixed several switch statements, curly braces, dereference operators
and keywords.
Signed-off-by: Robin Schroer <sulamiification@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our two ->crtc_mode_set callbacks really don't care whether the fb is
pinned and set up already or not - all the state computation and
handling which originally looked at the framebuffer is already using
the indirection through the pipe configuration.
Eventually we want to move this up a bit more, but as long as the crtc
mode_set callback still exists (and as long as we don't need to pin an
entire pile of planes due to atomic modesets) there's not much point
in it. So I'll let this be for now.
v2: Don't forget about haswell ...
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A lot of the code in set_base is uncessary when the crtc is off, so we
can get rid of it all. Also, we don't need to call the fbc/psr update
functions since the crtc enable/disable hooks do that already.
The only things we really need are:
- Pin the new framebuffer and potentially unpin the old framebuffer
(if the crtc has been on and we only change the configuration).
- Update the plane registers.
The first step will move out of platform code with the very next
patch.
v2: Don't forget about haswell ...
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My plan here is to split up set_base into a prepare step, which does
the pinning, and a commit stage, which updates the hw state. Eventually
we should be able to move the prepare step at the beginning of any
atomic update. For now I only want to move the commit step into the
crtc_enable callbacks.
As a prep step sprinkle intel_edp_psr_update all over the place so
that we don't have to concern ourselves with that in the commit step.
v2: Rebase on top of Ville's enable/disable functions for all planes.
v3: Rebase more.
Reviewed-by: Akash Goel <akash.goel@intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just for consistency, this patch won't fix anything really.
v2: Rebase over all the recent plane enabling shuffling.
Reviewed-by: Akash Goel <akash.goel@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Way back we've used this to reject framebuffers with unsupported
pixel formats. But since the modesetting reorg with the compute
config stage we reject those much earlier and just BUG() in this
callback. So switch to a void return type.
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Including state readout and cross-checking. This allows us to get rid
of crtc->eld_vld on hsw+. It also means that fastboot will be unhappy
if the BIOS hasn't set up the audio routing like we want it too.
Wrt fastboot and external screens I see a few options:
- Don't.
- Try to fix up eld, infoframes and audio settings after the fact. But
that means some pretty extensive reworking of our code which
currently does all this while the pipe/port is still off.
I won't bother with converting SDVO over to this because the audio
support for SDVO is very lacking:
- We don't update the eld.
- We don't update the audio state on the sdvo encoder.
- We don't check whether the platform can even feed audio to the sdvo
encoder.
I've converted hdmi, dp & ddi all in one go since ddi needs both hdmi
and dp converted and so doing it step-by-step would have required a
few intermediate hacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on those platforms which have a simple bit and don't rely
on the fully programmable CSC unit to do this.
Note that with the current code this includes CHV, but I guess that
platform will match BYT.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also add state readout and cross-check support. The only invasive change
is wiring up the new flag to the ->set_infoframes callbacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Patch done using the following semantic patch (thanks Daniel for the
help!)
@@
iterator name list_for_each_entry;
iterator name for_each_crtc;
struct drm_crtc * crtc;
struct drm_device * dev;
@@
-list_for_each_entry(crtc,&dev->mode_config.crtc_list, head) {
+for_each_crtc(dev,crtc) {
...
}
Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Generated using the semantic patch:
@@
iterator name list_for_each_entry;
iterator name for_each_intel_crtc;
struct intel_crtc * crtc;
struct drm_device * dev;
@@
-list_for_each_entry(crtc,&dev->mode_config.crtc_list,...) {
+for_each_intel_crtc(dev,crtc) {
...
}
Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe might not start to actually run until the port has been enabled
(depends on the platform and port type). So don't try to wait for vblank
after we enabled the pipe but haven't yet enabled the port.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already moved the plane disable/enable to happen as the first/last
thing on every other platforms. Follow suit with gmch platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Frob drm_vblank_on conflict, as usual.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No CRT output on CHV, so don't call intel_crt_init().
v2: Don't disable CRT on HAS.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add chv_crtc_clock_get() to read out the DPLL settings.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Fix compile due to bikeshedded headers in an earlier patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming PLL for CHV based on "Application note for 1273 CHV
Display phy".
v2: -Break the common lane reset into another patch.
-Break the clock calculation into another patch.
-The changes are based on Ville review.
-Rework based on DPIO register define naming convention change.
-Break the dpio write into few lines to improve readability.
-Correct the udelay during chv_enable_pll.
-clean up some magic numbers with some new define.
-program the afc recal bit which was missed.
v3: Based on Ville review
- minor correction of the bit defination
- add deassert/propagate data lane reset
v4: Corrected the udelay between dclkp enable and pll enable.
Minor comment and better way to clear the TX lane reset.
v5: Squash in fixup from Rafael Barbalho.
[vsyrjala: v6: Polish the defines (Imre)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the chv clock limit, find the best divisor.
The divisor data has been verified with this spreadsheet.
P1273_DPLL_Programming Spreadsheet.
v2: Rebase the code and change the chv_find_best_dpll based on new
standard way to use intel_PLL_is_valid. Besides, clean up some extra
variables.
v3: Ville suggest better fixed point for m2 calculation.
v4: -Add comment for the limit is compute using fast clock. (Ville)
-Don't pass the request clock to chv_clock, as the same function will
be use clock readout, which doens't have request clock. (Ville)
-Add and use DIV_ROUND_CLOSEST_ULL to consistent with other clock
calculation. (Ville)
-Fix the dp m2 after m2 has stored fixed point. (Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Avoid div-by-zero in chv_clock()]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During cold boot, the display controller needs to deassert the common
lane reset. Only do it once during intel_init_dpio for both PHYx2 and
PHYx1.
Besides, assert the common lane reset when disable pll. This still
to be determined whether need to do it by driver.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Don't disable DPIO PLL when using DSI]
[vsyrjala: Don't call vlv_disable_pll() by accident on CHV]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Move part of a moved comment back as suggested by Imre since
it's valid for both byt and chv.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The additional DPLL registers added to support Port D. Besides, add
some new PHY control and status registers based on B-spec.
v2: Based on Ville review
- Corrected DPIO_PHY_STATUS offset and name.
- Rebase based on upstream change after introduce enum dpio_phy and
enum dpio_channel.
v3: Rebased on top of Antti's 3-pipe prep patch. Note that the new offsets for
the DPLL registers aren't in place yet, so this introduces a slight regression.
But since 3 pipe support isn't fully enabled yet anyaway in -internal this
shouldn't matter too much.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has 2 display phys. First phy (IOSF offset 0x1A) has two channels,
and second phy (IOSF offset 0x12) has single channel. The first phy is
used for port B and port C, while second phy is only for port D.
v2: Move the pipe to determine which phy to select for
vlv_dpio_read/vlv_dpio_write to another patch. (Daniel)
v3: Rebase the code based on rework on how to calculate DPIO offset.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the same code for enabling/disabling planes on all platforms. Rename
the functions to reflect that they're no longer specific to any
platform.
For now we leave the plane enable/disable to ccur at the same old
position in the modeset sequence.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Frob drm_vblank_on conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We won't be calling intel_enable_primary_plane() or
intel_disable_primary_plane() with the primary plane in the
wrong state. So remove the useless DISPLAY_PLANE_ENABLE checks.
v2: Convert the checks to WARNs instead (Daniel,Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a mechanism by which we can evade the leading edge of vblank. This
guarantees that no two sprite register writes will straddle on either
side of the vblank start, and that means all the writes will be latched
together in one atomic operation.
We do the vblank evade by checking the scanline counter, and if it's too
close to the start of vblank (too close has been hardcoded to 100usec
for now), we will wait for the vblank start to pass. In order to
eliminate random delayes from the rest of the system, we operate with
interrupts disabled, except when waiting for the vblank obviously.
Note that we now go digging through pipe_to_crtc_mapping[] in the
vblank interrupt handler, which is a bit dangerous since we set up
interrupts before the crtcs. However in this case since it's the vblank
interrupt, we don't actually unmask it until some piece of code
requests it.
v2: preempt_check_resched() calls after local_irq_enable() (Jesse)
Hook up the vblank irq stuff on BDW as well
v3: Pass intel_crtc instead of drm_crtc (Daniel)
Warn if crtc.mutex isn't locked (Daniel)
Add an explicit compiler barrier and document the barriers (Daniel)
Note the irq vs. modeset setup madness in the commit message (Daniel)
v4: Use prepare_to_wait() & co. directly and eliminate vbl_received
v5: Refactor intel_pipe_handle_vblank() vs. drm_handle_vblank() (Chris)
Check for min/max scanline <= 0 (Chris)
Don't call intel_pipe_update_end() if start failed totally (Chris)
Check that the vblank counters match on both sides of the critical
section (Chris)
v6: Fix atomic update for interlaced modes
v7: Reorder code for better readability (Chris)
v8: Drop preempt_check_resched(). It's not available to modules
anymore and isn't even needed unless we ourselves cause
a wakeup needing reschedule while interrupts are off
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reasons we want to move away from the ->mode_set
callbacks: All hw state setup needs to move into ->enable hooks (so
that DOMS can do runtime pm) and all the configuration setup needs to
move into the compute_config functions.
To start with this make the enocer->mode_set callback optional.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BIOS can enable a pipe but leave the primary plane disabled. This
coflicts with out current idea of primary_enabled. Read the actual
hardware plane state and set primary_enabled appropriately.
We currently assume that primary_enabled is always true when we're about
to disable a crtc. That needs to change now as the plane may not be
enabled. So replace the relevant WARNs with early returns in
intel_{enable,disable}_primary_hw_plane().
Fixes the following warning
[ 3.831602] WARNING: CPU: 0 PID: 1112 at linux/drivers/gpu/drm/i915/intel_display.c:1918 intel_disable_primary_hw_plane+0xe4/0xf0 [i915]()
which got introduced here by me:
commit e9e39655c0c30cddc3f8c09a757678a24dd36737
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Apr 28 15:53:25 2014 +0300
drm/i915: Remove useless checks from primary enable/disable
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
assert_plane_enabled() is now triggering during FDI link train because
we no longer enable planes that early.
This problem got introduced in:
commit a5c4d7bc18
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Mar 7 18:32:13 2014 +0200
drm/i915: Disable/enable planes as the first/last thing during modeset on ILK+
Just drop the assert since we shouldn't need planes for link training.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Squash in fixup for now unused plane local variable, reported
by 0-day tester.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init sizzling on all platforms so move it to the
platform independent runtime resume callback. The ring frequency reinit
is also needed everywhere except on VLV, but gen6_update_ring_freq()
will be a noop on VLV, so we can move this function too to platform
independent code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by the next patch moving the call out from platform
specific RPM callbacks to platform independent code.
No functional change.
v2:
- patch introduce in v2 of the patchset
v3:
- simplify platform check condition (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to disable the interrupts for all platforms, so make the helpers
for this platform independent and call them from them platform
independent runtime suspend/resume callbacks.
On HSW/BDW this will move interrupt disabling/re-enabling at the
beginning/end of runtime suspend/resume respectively, but I don't see
any reason why this would cause a problem there. In any case this seems
to be the correct thing to do even on those platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While checking the error capture path I noticed that we lacked the
power domain-on check for PIPESTAT so fix this by moving that to where
the rest of pipe registers are captured.
The move also revealed that we actually don't include this register in
the error report, so fix that too.
v2:
- patch introduced in v2 of the patchset
v3:
- add back !HAS_PCH_SPLIT check (Ville)
[ Ignore my previous comment about the gen<=5 || vlv check, I realized
that it's the same as !HAS_PCH_SPLIT. ]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
Depending on the SDVO output_flags SDVO may have multiple connectors
linking to the same encoder (in intel_connector->encoder->base).
Only one of those connectors should be active (ie link to the encoder
thru drm_connector->encoder).
If intel_connector_break_all_links() is called from intel_sanitize_crtc()
we may break the crtc connection of an encoder thru an inactive connector
in which case intel_connector_break_all_links() will not be called again
for the active connector if this happens to come later in the list due to:
if (connector->encoder->base.crtc != &crtc->base)
continue;
in intel_sanitize_crtc().
This will however leave the drm_connector->encoder linkage for this
active connector in place. Subsequently this will cause multiple
warnings in intel_connector_check_state() to trigger and the driver
will eventually die in drm_encoder_crtc_ok() (because of crtc == NULL).
To avoid this remove intel_connector_break_all_links() and move its
code to its two calling functions: intel_sanitize_crtc() and
intel_sanitize_encoder().
This allows to implement the link breaking more flexibly matching
the surrounding code: ie. in intel_sanitize_crtc() we can break the
crtc link separatly after the links to the encoders have been
broken which avoids above problem.
This regression has been introduced in:
commit 2492935248
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jul 2 20:28:59 2012 +0200
drm/i915: read out the modeset hw state at load and resume time
so goes back to the very beginning of the modeset rework.
v2: This patch takes care of the concernes voiced by Chris Wilson
and Daniel Vetter that only breaking links if the drm_connector
is linked to an encoder may miss some links.
v3: move all encoder handling to encoder loop as suggested by
Daniel Vetter.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
... our current modeset code isn't good enough yet to handle this. The
scenario is:
1. BIOS sets up a cloned config with lvds+external screen on the same
pipe, e.g. pipe B.
2. We read out that state for pipe B and assign the gmch_pfit state to
it.
3. The initial modeset switches the lvds to pipe A but due to lack of
atomic modeset we don't recompute the config of pipe B.
-> both pipes now claim (in the sw pipe config structure) to use the
gmch_pfit, which just won't work.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74081
Tested-by: max <manikulin@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The pipe is off at that point in time, so a vblank wait is simply a
50ms wait. Caught by Jesse's verbose "make vblank wait timeouts WARN"
patch. We've probably had a few versions of this float around already.
To document assumptions put a pipe assert into the same place. And
also add a posting read.
If we ever decide to update the eld and infoframes while the pipe is
already on (e.g. for fastboot) then there's lots of work to do. So
better properly document all the hidden assumptions.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already do this for HSW, but doing it makes sense for everything else
as well. Extend it for ILK/SNB/IVB since that's where the new watermark
code is used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
[danvet: Resolve conflict since I've plucked this out of the middle of
Ville's series.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like on hsw/bdw the pipe isn't actually running yet at this point.
This holds for both pch ports and the cpu edp port according to my
testing on ilk, snb and ivb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a requirement added to the spec. This patch will prevent
persistent corruption on the display.
v2: Make the wait before the vblank wait. (Art)
Try to finish early by polling the register
s/present/prevent (Chris)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Upgrade debug output to ERROR.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
haswell_write_eld() is also used on broadwell, so let's not explicitely
mention Haswell. The rest of the function has plenty of debug output
which will print the function name, so we know where we are anyway.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Comment from Ben: It's a bit unclear whether we need this dance still
on bdw.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next after the big s/crtc->fb/crtc->primary->fb/
cocinelle patch to avoid endless amounts of conflict hilarity in my
-next queue for 3.16.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge window -fixes pull request as usual. Well, I did sneak in Jani's
drm_i915_private_t typedef removal, need to have fun with a big sed job
too ;-)
Otherwise:
- hdmi interlaced fixes (Jesse&Ville)
- pipe error/underrun/crc tracking fixes, regression in late 3.14-rc (but
not cc: stable since only really relevant for igt runs)
- large cursor wm fixes (Chris)
- fix gpu turbo boost/throttle again, was getting stuck due to vlv rps
patches (Chris+Imre)
- fix runtime pm fallout (Paulo)
- bios framebuffer inherit fix (Chris)
- a few smaller things
* tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel: (196 commits)
Skip intel_crt_init for Dell XPS 8700
drm/i915: vlv: fix RPS interrupt mask setting
Revert "drm/i915/vlv: fixup DDR freq detection per Punit spec"
drm/i915: move power domain init earlier during system resume
drm/i915: Fix the computation of required fb size for pipe
drm/i915: don't get/put runtime PM at the debugfs forcewake file
drm/i915: fix WARNs when reading DDI state while suspended
drm/i915: don't read cursor registers on powered down pipes
drm/i915: get runtime PM at i915_display_info
drm/i915: don't read pp_ctrl_reg if we're suspended
drm/i915: get runtime PM at i915_reg_read_ioctl
drm/i915: don't schedule force_wake_timer at gen6_read
drm/i915: vlv: reserve the GT power context only once during driver init
drm/i915: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/overlay: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/ringbuffer: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/display: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/irq: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/gem: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t
...
There's no point in hiding the DP M/N setup in the update_pll functions.
Just move it to the mode_set function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Inherit/reuse firmwar framebuffers (for real this time) from Jesse, less
flicker for fastbooting.
- More flexible cloning for hdmi (Ville).
- Some PPGTT fixes from Ben.
- Ring init fixes from Naresh Kumar.
- set_cache_level regression fixes for the vma conversion from Ville&Chris.
- Conversion to the new dp aux helpers (Jani).
- Unification of runtime pm with pc8 support from Paulo, prep work for runtime
pm on other platforms than HSW.
- Larger cursor sizes (Sagar Kamble).
- Piles of improvements and fixes all over, as usual.
* tag 'drm-intel-next-2014-03-21' of git://anongit.freedesktop.org/drm-intel: (75 commits)
drm/i915: Include a note about the dangers of I915_READ64/I915_WRITE64
drm/i915/sdvo: fix questionable return value check
drm/i915: Fix unsafe loop iteration over vma whilst unbinding them
drm/i915: Enabling 128x128 and 256x256 ARGB Cursor Support
drm/i915: Print how many objects are shared in per-process stats
drm/i915: Per-process stats work better when evaluated per-process
drm/i915: remove rps local variables
drm/i915: Remove extraneous MMIO for RPS
drm/i915: Rename and comment all the RPS *stuff*
drm/i915: Store the HW min frequency as min_freq
drm/i915: Fix coding style for RPS
drm/i915: Reorganize the overclock code
drm/i915: init pm.suspended earlier
drm/i915: update the PC8 and runtime PM documentation
drm/i915: rename __hsw_do_{en, dis}able_pc8
drm/i915: kill struct i915_package_c8
drm/i915: move pc8.irqs_disabled to pm.irqs_disabled
drm/i915: remove dev_priv->pc8.enabled
drm/i915: don't get/put PC8 when getting/putting power wells
drm/i915: make intel_aux_display_runtime_get get runtime PM, not PC8
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Because if we keep the current code, we'll get tons of WARNs on
Broadwell, since the code is Haswell-specific.
We could have also added a Broadwell-specific code there, but it's not
really needed since we never disable LCPLL with the hotplug interrupts
still enabled. So keep the easy-and-simple-to-maintain solution until
we actually need something else.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Ensure that existing driver loops over all planes do not change behavior
when we begin adding new types of planes (primary and cursor) to the DRM
plane list in future patches.
v2: Switch to using drm_for_each_legacy_plane()
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
That's what the spec said! And HSW needs it through pcode (you can
only read it through MCHBAR), so create hsw_write_dcomp to abstract
the weirdness.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that PC8 is part of runtime PM, the check is useless.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just because I have a SNB machine and I can easily test it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we don't keep the hotplug interrupts enabled anymore, we can
kill the regsave struct and just cal the normal IRQ preinstall,
postinstall and uninstall functions. This makes it easier to add
runtime PM support to non-HSW platforms.
The only downside is in case we get a request to update interrupts
while they are disabled, won't be able to update the regsave struct.
But this should never happen anyway, so we're not losing too much.
v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These were apparently meant to protect the SAREA which only has
room for two pipes, but things clearly went a bit wonky when
first the .update_plane() hooks were split up and then pipe C
got introduced.
The checks actually protecting the SAREA live in
intel_crtc_update_sarea() these days, so the checks in the primary
plane update hooks are just historical leftovers which are to be
eliminated.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those values are, global, only used in one function and already stored
in mode_config.cursor_{width,height}.
As a result, this initialization code has been moved from the
crtc_init() function to the global modeset_init() one.
I also renamed CURSOR_{WIDTH,HEIGHT} to MAX_CURSOR_{WIDTH,HEIGHT} to be
more accurate about what these value really are.
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of reading out the CD clock rate from the HW at each modeset, do
this only during driver init and resume and use the cached value during
modeset. This moves things towards a state where the sw and hw side
setup is separated. It's also needed for VLV RPM, where we don't put
device into D0 state until modeset_global_resources is called and thus
can't access any display/gfx registers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we reserve/allocate and free the power context during GT power
enable/disable time. There is no need to do this, we can reserve/allocate
the buffer once during driver loading and free it during driver cleanup.
The re-reservation can also fail in case the driver previously manages to
allocate something on the given fixed address.
The buffer isn't exepected to move even if allocated by the BIOS, for
safety add an assert to check this assumption.
This also fixed a bug for Ville, where re-reserving the context failed
during a GPU reset (I assume because something else got allocated on its
fixed address).
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If vsyncshift comes out as negative, add one htotal to it to get the
corresponding positive value.
This is rather theoretical as it would require a mode where the
hsync+back porch is very long and the active+front porch very short.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PIPECONF_INTERLACE_W_FIELD_INDICATION is only meant to be used for sdvo
since it implies a slightly weird vsync shift of htotal/2. For everything
else we should use PIPECONF_INTERLACE_W_SYNC_SHIFT and let the value in
the VSYNCSHIFT register take effect.
The only exception is gen3 simply because VSYNCSHIFT didn't exist yet.
Gen2 doesn't support interlaced modes at all, so we can drop the
explicit gen2 checks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When interlaced sdvo output is used, vsyncshift should supposedly
be (htotal-1)/2. In reality PIPECONF/TRANSCONF will override it by
using the legacy vsyncshift interlace mode which causes the hardware
to ignore the VSYNCSHIFT register.
The only odd thing here is that on PCH platforms we program the
VSYNCSHIFT on both CPU and PCH, and it's not entirely clear if both
sides have to agree on the value or not. On the CPU side there's no
way to override the value via PIPECONF anymore, so if we want to make
the CPU side agree with the PCH side, we should probably program the
approriate value into VSYNCSHIFT manually. So let's do that, but for
now leave the PCH side to still use the legacy interlace mode in
TRANSCONF.
We can also drop the gen2 check since gen2 doesn't support interlaced
modes at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes HDMI testers happier on VLV platforms. It may be that we
need it for any non-SVO platform, but I don't have any tests to back
that up, so I'm leaving other pre-ILK platforms alone for now.
Tested-by: "Clint Taylor <clinton.a.taylor@intel.com>"
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74964
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the cursor width is changed, we may need to recompute our WM to
prevent untold flickering. We hope that the registers are flushed on the
same vblank to prevent underruns...
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit 5c673b60a9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Mar 7 20:34:46 2014 +0100
drm/i915: Don't enable display error interrupts from the start
we don't enable underrun interrupts any more at takeover time.
Unfortunately I've forgotten to also adjust the sw-side tracking.
Since the code assumes that disabled pipes have underrun reporting
enabled set the disable flag only on all pipes which are active at
takeover time. Without this underrun reporting wasn't enabled
correctly on the first modeset. Note that for fastboot this is another
piece of state that needs to be fixed up by enabling the underrung
reporting after watermarks have beend fixed up.
On ivb/hsw an additional effect of this regression was that also all
cpu crc reporting stopped working since the master error interrupt it
shared across all pipes and sources.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76150
[danvet: Augment the code comment and polish the commit message a bit,
as discussed with Jani.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: lu hua <huax.lu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this patch we allow larger cursor planes of sizes 128x128
and 256x256.
v2: Added more precise check on size while setting cursor plane.
v3: Changes related to restructuring cursor size restrictions
and DRM_DEBUG usage.
v4: Indentation related changes for setting cursor control and
implementing DRM_CAP_CURSOR_WIDTH and DRM_CAP_CURSOR_HEIGHT
Testcase: igt/kms_cursor_crc
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: G, Pallavi <pallavi.g@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that PC8 got much simpler, there are less things to document.
Also, runtime PM already has a nice documentation, so we don't need to
re-explain it on our driver.
v2: - Rebase.
- Fix typo (Jesse).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After we removed all the intermediate abstractions, we can rename
these functions to just hsw_{en,dis}able_pc8.
v2: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When other platforms add runtime PM support they will also need to
disable interrupts, so move the variable to the runtime PM struct.
Also notice that the longer-term goal is to completely kill the
regsave struct, and I even have patches for that.
v2: - Rebase.
v3: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It was just being used on debugfs and on a WARN inside
hsw_set_power_well. But now that we PC8 is part of runtime PM and we
get/put runtime PM when we get/put any power domain, we shouldn't need
the WARN anymore.
v2: - Rebase.
v3: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we already get/put runtime PM every time we get/put any power
domain, and now PC8 and runtime PM are the same thing.
With this, we can also now kill the hsw_{en,dis}able_package_c8
functions.
v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the latest changes, the indirection is useless.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since after the latest patches it's only being used to prevent
getting/putting the runtime PM refcount.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of PC8 references. Now that both are the same thing and we
are killing PC8, just get the runtime PM reference.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The requirements_met variable was used to track two things: enabled
CRTCs and the power well. After the latest chagnes, we get a runtime
PM reference whenever we get any of the power domains, and we get
power domains when we enable CRTCs or the power well, so we should
already be covered, not needing this specific tracking.
v2: - Rebase.
v3: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, when our driver becomes idle for i915.pc8_timeout (default:
5s) we enable PC8, so we save some power, but not everything we can.
Then, while PC8 is enabled, if we stay idle for more
autosuspend_delay_ms (default: 10s) we'll enter runtime PM and put the
graphics device in D3 state, saving even more power. The two features
are separate things with increasing levels of power savings, but if we
disable PC8 we'll never get into D3.
While from the modularity point of view it would be nice to keep these
features as separate, we have reasons to merge them:
- We are not aware of anybody wanting a "PC8 without D3" environment.
- If we keep both features as separate, we'll have to to test both
PC8 and PC8+D3 code paths. We're already having a major pain to
make QA do automated testing of just one thing, testing both paths
will cost even more.
- Only Haswell+ supports PC8, so if we want to add runtime PM support
to, for example, IVB, we'll have to copy some code from the PC8
feature to runtime PM, so merging both features as a single thing
will make it easier for enabling runtime PM on other platforms.
This patch only does the very basic steps required to have PC8 and
runtime PM merged on a single feature: the next patches will take care
of cleaning up everything.
v2: - Rebase.
v3: - Rebase.
- Fully remove the deprecated i915 params since Daniel doesn't
consider them as part of the ABI.
v4: - Rebase.
- Fix typo in the commit message.
v5: - Rebase, again.
- Add a huge comment explaining the different forcewake usage
(Chris, Daniel).
- Use open-coded forcewake functions (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we merge PC8 and runtime PM, these new functions are going to be
called by the runtime suspend/resume functions, and their callers are
going to be removed.
v2: - Rebase
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The name 'update_plane' was used both for the primary plane functions in
intel_display.c and the sprite/overlay functions in intel_sprite.c.
Rename the primary plane functions to 'update_primary_plane' to avoid
confusion.
On a similar note, intel_display.c already had a function called
intel_disable_primary_plane() that programs the hardware to disable a
pipe's primary plane. When we hook up primary planes through the DRM
plane interface, one of the natural handler names will be
intel_primary_plane_disable(), which is very similar. To avoid
confusion, rename the existing intel_disable_primary_plane() to
intel_disable_primary_hw_plane() to make the two names a little more
distinct.
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
[danvet: Fix up conflicts.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTJlUvAAoJEHm+PkMAQRiGOhYH/1I+Bc7N7Rjr6QQAtBIy0GPC
XMqSE/gpgxlvRneQbQsvTUlPnWRhgzLGendT9HFKawkaQ0UNuZdRVyBHGFmpuED8
RlbicVVuuEZabrxEnCd7UPvYvEyK5pLIFpCRs5B+ManB1qLki2Ar03ymH1NRxOde
edmPbSUFo2aONITrEBm7tqT3cShTmBaDGP/zU0TNDMNrpVVDbHZolSNu2z4xOTa5
GqAOEbluLQ6jP3yxWur/V3Lk3W7pB6TabfX4o6UZu0F3iFnJxRMIzHXrI3o4yLTj
HEwmB3npfc8DIUk4oik7RkN+aqxDcdg/rBLQD63+xxt6zCkP+0q16brC0R67qWE=
=n9Ml
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc7' into drm-next
Linux 3.14-rc7
Backmerge to help out Intel guys.
Conflicts:
drivers/gpu/drm/i915/Makefile
Makefile cleanup in drm-intel-next conflicts with a build-fix to move
intel_opregion under CONFIG_ACPI.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't need to hold struct_mutex all through intel_pipe_set_base(),
just need to hold it while pinning/unpinning the buffers.
So reduce the struct_mutext usage in intel_pipe_set_base() just like we
did for the sprite code in:
commit 82284b6bec
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Oct 1 18:02:12 2013 +0300
drm/i915: Reduce the time we hold struct mutex in sprite update_plane code
The FBC and PSR locking is still entirely fubar. That stuff was
previouly done while holding struct_mutex, so leave it there for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTHSaRAAoJEHm+PkMAQRiG7G8IAJHElwFDNSQE7Y9MmbicrAMG
kfjhBtBpTaVrJKQXegCNUwDaLLyC4oLIxDheW84oPXbrEGDLqPtBov/hrcFkHVr4
lh/ZYk02nYtcfpN0JnL/Yj2oKHVmBWs0vFlM7StSFsJCj10DoCVQQdmAJ8XODTPo
CXMapk+UikTX1TlIO8+B5toyl3R1OqPmW211UV1vQVLKy66hu+MKVN/V+/EyopL0
1jO81EDpaRaeIJh1/okcyUoIq9pqLkAWNpeQ7uyXZ+Sfivt9RXwLYKmAB3lP20Hc
ZMIIoHSCyYRFjxLlQvt02bA9nY4wTY7YN5kZ2kk65y7TFfhcGsCw1Sc69iyCoKs=
=CJcA
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc6' into drm-intel-next-queued
Linux 3.14-rc6
I need the hdmi/dvi-dual link fixes in 3.14 to avoid ugly conflicts
when merging Ville's new hdmi cloning support into my -next tree
Conflicts:
drivers/gpu/drm/i915/Makefile
drivers/gpu/drm/i915/intel_dp.c
Makefile cleanup conflicts with an acpi build fix, intel_dp.c is
trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we allow encoders to indicate whether they can be part of a
cloned set with just one flag. That's not flexible enough to describe
the actual hardware capabilities. Instead make it a bitmask of encoder
types with which the current encoder can be cloned.
For now we set the bitmask to allow DVO+DVO and DVO+VGA, which should
match what the old boolean flag allowed. We will add some more cloning
options in the future.
Note that this patch also removes the encoder.possible_clones setting
from encoder setup code - we compute this dynamically.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add Ville's explanation why removing the encoder
possible_clones is save.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The stolen allocator objects loudly if the caller requests a zero-sized
object. This is a useful verbose check as in most cases the request
should have been pruned much early. Here we just want to silently return
before attempting the allocation.
Regression from
commit 484b41dd70
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Mar 7 08:57:55 2014 -0800
drm/i915: remove early fb allocation dependency on CONFIG_FB v2
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=75963
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During KMS takeover, we try to capture the current configuration and
preserve it across our initialisation. For a variety of reasons, we may
fail this, for example if the current mode was using the legacy VGA
plane. Under such circumstances, we discard the fb in the plane config
and tried to find a matching fb on another CRTC. This obviously also
failed, leaving the plane config fb dangling, pointing to the freed block.
Regression from
commit 484b41dd70
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Mar 7 08:57:55 2014 -0800
drm/i915: remove early fb allocation dependency on CONFIG_FB v2
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=75963
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By stuffing the fb allocation into the crtc, we get mode set lifetime
refcounting for free, but have to handle the initial pin & fence
slightly differently. It also means we can move the shared fb handling
into the core rather than leaving it out in the fbdev code.
v2: null out crtc->fb on error (Daniel)
take fbdev fb ref and remove unused error path (Daniel)
Requested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Retrieve current framebuffer config info from the regs and create an fb
object for the buffer the BIOS or boot loader left us. This should
allow for smooth transitions to userspace apps once we finish the
initial configuration construction.
v2: check for non-native modes and adjust (Jesse)
fixup aperture and cmap frees (Imre)
use unlocked unref if init_bios fails (Jesse)
fix curly brace around DSPADDR check (Imre)
comment failure path for pin_and_fence (Imre)
v3: fixup fixup of aperture frees (Chris)
v4: update to current bits (locking & pin_and_fence hack) (Jesse)
v5: move fb config fetch to display code (Jesse)
re-order hw state readout on initial load to suit fb inherit (Jesse)
re-add pin_and_fence in fbdev code to make sure we refcount properly (Je
v6: rename to plane_config (Daniel)
check for valid object when initializing BIOS fb (Jesse)
split from plane_config readout and other display changes (Jesse)
drop use_bios_fb option (Chris)
update comments (Jesse)
rework fbdev_init_bios for clarity (Jesse)
drop fb obj ref under lock (Chris)
v7: use fb object from plane_config instead (Ville)
take ref on fb object (Jesse)
v8: put under i915_fastboot option (Jesse)
fix fb ptr checking (Jesse)
inform drm_fb_helper if we fail to enable a connector (Jesse)
drop unnecessary enabled[] modifications in failure cases (Chris)
split from BIOS connector config readout (Daniel)
don't memset the fb buffer if preallocated (Chris)
alloc ifbdev up front and pass to init_bios (Chris)
check for bad ifbdev in restore_mode too (Chris)
v9: fix up !fastboot bpp setting (Jesse)
fix up !fastboot helper alloc (Jesse)
make sure BIOS fb is sufficient for biggest active pipe (Jesse)
v10:fix up size calculation for proposed fbs (Chris)
go back to two pass pipe fb assignment (Chris)
add warning for active pipes w/o fbs (Chris)
clean up num_pipes checks in fbdev_init and fbdev_restore_mode (Chris)
move i915.fastboot into fbdev_init (Chris)
v11:make BIOS connector config usage unconditional (Daniel)
v12:fix up fb vs pipe size checking (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should allow BIOS fb inheritance to work on ILK+ machines too.
v2: handle tiled BIOS fbs (Kristian)
split out common bits (Jesse)
v3: alloc fb obj out in _init
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the current plane configuration at init time into a new
plane_config structure. This allows us to track any existing
framebuffers attached to the plane and potentially re-use them in our
fbdev code for a smooth handoff.
v2: update for new pitch_for_width function (Jesse)
comment how get_plane_config works with shared fbs (Jesse)
v3: s/ARGB/XRGB (Ville)
use pipesrc width/height (Ville)
fix fourcc comment (Bob)
use drm_format_plane_cpp (Ville)
v4: use fb for tracking fb data object (Ville)
v5: fix up gen2 pitch limits (Ville)
v6: read out stride as well (Daniel)
v7: split out init ordering changes (Daniel)
don't fetch config if !CONFIG_FB
v8: use proper height in get_plane_config (Chris)
v9: fix CONFIG_FB check for modular configs (Jani)
v10: add comment about stolen allocation stomping
v11: drop hw state readout hunk (Daniel)
v12: handle tiled BIOS fbs (Kristian)
pull out common bits (Jesse)
v13: move fb obj alloc out to _init
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Early at init time, we can try to read out the plane config structure
and try to preserve it if possible.
v2: alloc fb obj at init time after fetching plane config
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on an early draft from Jesse.
Add support for powering on/off the dynamic power wells on VLV by
registering its display and dpio dynamic power wells with the power
domain framework.
For now power on all PHY TX lanes regardless of the actual lane
configuration. Later this can be optimized when the PHY side setup
enables only the required lanes. Atm, it enables all lanes in all
cases.
v2:
- undef function local COND macro after its last use (Ville)
- Take dev_priv->irq_lock around the whole sequence of
intel_set_cpu_fifo_underrun_reporting_nolock() and
valleyview_disable_display_irqs(). They are short and releasing
the lock in between only makes proving correctness more difficult.
- sanitize local var names in vlv_power_well_enabled()
v3:
- rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict due to my changes in the previous patch.
Also throw in an assert_spin_locked for safety. And finally appease
checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can read out the pipe HW state only if the required power domain is
on. If not we consider the pipe to be off.
v2:
- no change
v3:
- push down the power domain checks into the specific crtc
get_pipe_config handlers (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Parts that poke port specific HW blocks like the encoder HW state
readout or connector hotplug detect code need a way to check whether
required power domains are on or enable/disable these. For this purpose
add a set of power domains that refer to the port HW blocks. Get the
proper port power domains during modeset.
For now when requesting the power domain for a DDI port get it for a 4
lane configuration. This can be optimized later to request only the 2
lane power domain, when proper support is added on the VLV PHY side for
this. Atm, the PHY setup code assumes a 4 lane config in all cases.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions will be needed by the valleyview specific power well
update functionality added in an upcoming patch, so move them earlier.
No functional change.
v2:
- no change
v3:
- rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This macro is similar to for_each_pipe() we already have. Convert the
two call sites we have at the same time.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I recently fumbled a patch because I wrote twice num_sprites[i], and it
was the right thing to do in only 50% of the cases.
This patch ensures I need to write num_sprites[pipe], ie it should be
self-documented that it's per-pipe number of sprites without having to
look at what is 'i' this time around.
It's all a lame excuse, but it does make it harder to redo the same
mistake.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we need precisely N lanes to satisfy the FDI bandwidth requirement,
the code would still claim that we need N+1 lanes. Use DIV_ROUND_UP()
to get a more accurate answer.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After a hang and failed reset, we cannot use the GPU to execute the page
flip instructions. Instead we can force a synchronous mmio flip. (Later,
we can reduce the synchronicity of the mmio flip by moving some of the
delays off to a worker, like the current page flip code; see vblank
tasks.)
References: https://bugs.freedesktop.org/show_bug.cgi?id=72631
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the addition of dev_priv->mm.busy, there's no more need for
dev_priv->pc8.gpu_idle, so kill it.
Notice that when you remove gpu_idle, hsw_package_c8_gpu_idle and
hsw_package_c8_gpu_busy become identical to hsw_enable_package_c8 and
hsw_disable_package_c8, so just use them.
Also, when we boot the machine, dev_priv->mm.busy initially considers
the machine as idle. This is opposed to dev_priv->pc8.gpu_idle, which
considered it busy. So dev_priv->pc8.disable_count has to be
initalized to 1 now.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because intel_mark_idle still touches some registers: it needs the
machine to be awake. If you set both the autosuspend and PC8 delays to
zero, you can get a "Device suspended" WARN when gen6_rps_idle touches
registers.
This is not easy to reproduce, but happens once in a while when
running pm_pc8.
Testcase: igt/pm_pc8
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently call intel_mark_idle() too often, as we do so as a
side-effect of processing the request queue. However, we the calls to
intel_mark_idle() are expected to be paired with a call to
intel_mark_busy() (or else we try to idle the hardware by accessing
registers that are already disabled). Make the idle/busy tracking
explicit to prevent the multiple calls.
v2: We can drop some of the complexity in __i915_add_request() as
queue_delayed_work() already behaves as we want (not requeuing the item
if it is already in the queue) and mark_busy/mark_idle imply that the
idle task is inactive.
v3: We do still need to cancel the pending idle task so that it is sent
again after the current busy load completes (not in the middle of it).
Reported-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we can reuse the check on other platforms too. Also factor out
a version of the function that doesn't check if the power is on, we'll
need to call this from within the power domain framework.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power domains framework is internal to the i915 driver, so pass
drm_i915_private instead of drm_device to its functions.
Also remove a dangling intel_set_power_well() declaration.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should be impossible due to the wait for outstanding flips that the
caller is meant to perform prior to updating the scanout base. Paranoia
tells me to check anyway.
References: https://bugs.freedesktop.org/show_bug.cgi?id=75502
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To silence locking complaints. This was a rebase failure on my part in
commit fa9fa083d0
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Feb 11 15:28:56 2014 -0800
drm/i915: read out hw state earlier v2
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To modeset_update_crtc_power_domains, since this function is
responsible for updating all the power domains of all CRTCs after a
modeset. In the future we should also run this function on all
platforms, not just Haswell.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Fix the execbuf rebind performance regression due to topic/ppgtt (Chris).
- Fix up the connector cleanup ordering for sdvod i2c and dp aux devices (Imre).
- Try to preserve the firmware modeset config on driver load. And a bit of prep
work for smooth takeover of the fb contents (Jesse).
- Prep cleanup for larger gtt address spaces on bdw (Ben).
- Improve our vblank_wait code to make hsw modesets faster (Paulo).
- Display debugfs file (Jesse).
- DRRS prep work from Vandana Kannan.
- pipestat interrupt handler to fix a few races around vblank/pageflip handling
on byt (Imre).
- Improve display fuse handling for display-less SKUs (Damien).
- Drop locks while stalling for the gpu when serving pagefaults to improve
interactivity (Chris).
- And as usual piles of other improvements and small fixes all over.
* tag 'drm-intel-next-2014-02-14' of ssh://git.freedesktop.org/git/drm-intel: (65 commits)
drm/i915: fix NULL deref in the load detect code
drm/i915: Only bind each object rather than for every execbuffer
drm/i915: Directly return the vma from bind_to_vm
drm/i915: Simplify i915_gem_object_ggtt_unpin
drm/i915: Allow blocking in the PDE alloc when running low on gtt space
drm/i915: Don't allocate context pages as mappable
drm/i915: Handle set_cache_level errors in the status page setup
drm/i915: Don't pin the status page as mappable
drm/i915: Don't set PIN_MAPPABLE for legacy ringbuffers
drm/i915: Handle set_cache_level errors in the pipe control scratch setup
drm/i915: split PIN_GLOBAL out from PIN_MAPPABLE
drm/i915: Consolidate binding parameters into flags
drm/i915: sdvo: add i2c sysfs symlink to the connector's directory
drm/i915: sdvo: fix error path in sdvo_connector_init
drm/i915: dp: fix order of dp aux i2c device cleanup
drm/i915: add unregister callback to connector
drm/i915: don't reference null pointer at i915_sink_crc
drm/i915/lvds: Remove dead code from failing case
drm/i915: don't preserve inherited configs with nothing on v2
drm/i915/bdw: Split up PPGTT cleanup
...
We need to read the correct register, not a register that doesn't exist
and will trigger "Unclaimed register" messages when we touch it.
Also rearrange the checks in an attempt to prevent this error from
happening again.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: dropped an extra empty line introduced.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Apparently we've missed a few more than what Fengguang's 0-day tester
recently reported in i915_irq.c ... Makes sparse happy again (ignore
some spurious stuff about ksyms of exported functions).
Cc: kbuild test robot <fengguang.wu@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Yet more steps towards atomic modeset from Ville.
- DP panel power sequencing improvements from Paulo.
- irq code cleanups from Ville.
- 5.4 GHz dp lane clock support for bdw/hsw from Todd.
- Clock readout support for hsw/bdw (aka fastboot) from Jesse.
- Make pipe underruns report at ERROR level (Ville). This is to check our
improved watermarks code.
- Full ppgtt support from Ben for gen7.
- More fbc fixes and improvements from Ville all over the place, unfortunately
not yet enabled by default on more platforms.
- w/a cleanups from Ville.
- HiZ stall optimization settings (Chia-I Wu).
- Display register mmio offset refactor patch from Antti.
- RPS improvements for corner-cases from Jeff McGee.
* tag 'drm-intel-next-2014-02-07' of ssh://git.freedesktop.org/git/drm-intel: (166 commits)
drm/i915: Update rps interrupt limits
drm/i915: Restore rps/rc6 on reset
drm/i915: Prevent recursion by retiring requests when the ring is full
drm/i915: Generate a hang error code
drm/i915: unify FLIP_DONE macro names
drm/i915: vlv: s/spin_lock_irqsave/spin_lock/ in irq handler
drm/i915: factor out valleyview_pipestat_irq_handler
drm/i915: vlv: don't unmask IIR[DISPLAY_PIPE_A/B_VBLANK] interrupt
drm/i915: Reorganize display pipe register accesses
drm/i915: Treat using a purged buffer as a source of EFAULT
drm/i915: Convert EFAULT into a silent SIGBUS
drm/i915: release mutex in i915_gem_init()'s error path
drm/i915: check for oom when allocating private_default_ctx
drm/i915/vlv: WA to fix Voltage not getting dropped to Vmin when Gfx is power gated.
drm/i915: Get rid of acthd based guilty batch search
drm/i915: Use hangcheck score to find guilty context
drm/i915: Drop WaDisablePSDDualDispatchEnable:ivb for IVB GT2
drm/i915: Fix IVB GT2 WaDisableDopClockGating and WaDisablePSDDualDispatchEnable
drm/i915: Don't access snooped pages through the GTT (even for error capture)
drm/i915: Only print information for filing bug reports once
...
Conflicts:
drivers/gpu/drm/i915/intel_dp.c
3 fixes plus 1 prep patch, all four cc: stable. Jani will take over from
here and the plan is that he'll do 3.14-fixes for the entire release just
to work things out a bit.
* tag 'drm-intel-fixes-2014-02-14' of ssh://git.freedesktop.org/git/drm-intel:
drm/i915/dp: add native aux defer retry limit
drm/i915/dp: increase native aux defer retry timeout
drm/i915: Prevent MI_DISPLAY_FLIP straddling two cachelines on IVB
drm/i915: Add intel_ring_cachline_align()
Spotted while auditing the code for fencing issues.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like I've missed one of the potential NULL deref bugs in Jesse's
fbdev->fb embedded struct to pointer conversions. Fix it up.
This regression has been introduced in
commit 8bcd45534d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Feb 7 12:10:38 2014 -0800
drm/i915: alloc intel_fb in the intel_fbdev struct
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit d9255d5714
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Sep 26 20:05:59 2013 -0300
it became clear that we need to separate the unload sequence into two
parts:
1. remove all interfaces through which new operations on some object
(crtc, encoder, connector) can be started and make sure all pending
operations are completed
2. do the actual tear down of the internal representation of the above
objects
The above commit achieved this separation for connectors by splitting
out the sysfs removal part from the connector's destroy callback and
doing this removal before calling drm_mode_config_cleanup() which does
the actual tear-down of all the drm objects.
Since we'll have to customize the interface removal part for different
types of connectors in the upcoming patches, add a new unregister
callback and move the interface removal part to it.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We assign the sarea_priv pointer only in the dma ioctl, which is
disallowed when kernel modesetting is enabled. So this is dead code.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
