When wlc_phy_txpwr_srom_read_lcnphy fails in wlc_phy_attach_lcnphy,
the allocated pi->u.pi_lcnphy is leaked, since struct brcms_phy will be
freed in the caller function.
Fix this by calling wlc_phy_detach_lcnphy in the error handler of
wlc_phy_txpwr_srom_read_lcnphy before returning.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200908121743.23108-1-keitasuzuki.park@sslab.ics.keio.ac.jp
Setting F2 block size to 128 bytes for BCM4329 allows to significantly
improve RX throughput on NVIDIA Tegra20. Before this change the throughput
was capped to 30 Mbit/s on Tegra, now throughput is at 40 Mbit/s, which is
a maximum throughput for the BCM4329 chip. The F2 block size is borrowed
from the downstream BCMDHD driver. The comment in the BCMDHD driver says
that 128B improves throughput and turns out that it works for the brcmfmac
as well.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-4-digetx@gmail.com
The chip ID was already printed out at the time when debug message about
the changed F2 watermark is printed, hence let's drop the unnecessary part
of the debug messages. This cleans code a tad and also allows to re-use
the F2 watermark debug messages by multiple chips.
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-3-digetx@gmail.com
This patch fixes SDHCI CRC errors during of RX throughput testing on
BCM4329 chip if SDIO BUS is clocked above 25MHz. In particular the
checksum problem is observed on NVIDIA Tegra20 SoCs. The good watermark
value is borrowed from downstream BCMDHD driver and it's matching to the
value that is already used for the BCM4339 chip, hence let's re-use it
for BCM4329.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-2-digetx@gmail.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9218:18: warning: ‘papd_cal_scalars_tbl_core1_rev3’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9151:18: warning: ‘papd_comp_epsilon_tbl_core1_rev3’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9084:18: warning: ‘papd_cal_scalars_tbl_core0_rev3’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9017:18: warning: ‘papd_comp_epsilon_tbl_core0_rev3’ defined but not used [-Wunused-const-variable=]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-31-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_lcn.c:1510:33: warning: ‘dot11lcnphytbl_rx_gain_info_rev1’ defined but not used [-Wunused-const-variable=]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-30-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:16:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_spurwar_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:19036:6: warning: variable ‘tempval’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_tempsense_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:21983:28: warning: variable ‘RfctrlMiscReg6_save’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_rssi_compute_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:22986:6: warning: variable ‘phyRx0_l’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_runsamples_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23101:6: warning: variable ‘lpf_bw_ctl_miscreg4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23100:50: warning: variable ‘lpf_bw_ctl_miscreg3’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_iqcal_gainparams_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23406:6: warning: variable ‘idx’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_a2_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:24707:7: warning: variable ‘phy_a6’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_a3_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:24999:7: warning: variable ‘phy_a11’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-29-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:11:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_rx_iq_cal’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1366:29: warning: variable ‘RFOverride0_old’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_radio_2064_channel_tune_4313’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:21: warning: variable ‘qFvco’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:14: warning: variable ‘qFref’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:6: warning: variable ‘qFxtal’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_idle_tssi_est’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:2856:6: warning: variable ‘idleTssi’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_tx_iqlo_soft_cal_full’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:53: warning: variable ‘locc4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:46: warning: variable ‘locc3’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:39: warning: variable ‘locc2’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:32: warning: variable ‘iqcc0’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_periodic_cal’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4196:6: warning: variable ‘rx_iqcomp_sz’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4195:33: warning: variable ‘rx_iqcomp’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4194:16: warning: variable ‘full_cal’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_phy_txpwr_srom_read_lcnphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4919:7: warning: variable ‘opo’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-28-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'name' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'requested_packet' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'suppr_transit_count' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'send_tim_signal' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'traffic_pending_bmp' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'traffic_lastreported_bmp' not described in 'brcmf_fws_mac_descriptor'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c:12:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c: In function ‘wlc_phy_upd_env_txpwr_rate_limits’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c:1516:11: warning: variable ‘vbat’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c:1516:5: warning: variable ‘temp’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-9-lee.jones@linaro.org
Most likely caused by doc-rot.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'wdev' not described in 'brcmf_p2p_remain_on_channel'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2048: warning: Function parameter or member 'cfg' not described in 'brcmf_p2p_ifchange'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2048: warning: Excess function parameter 'mac' description in 'brcmf_p2p_ifchange'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-7-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:18:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus_complete’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:850:7: warning: variable ‘update_rate’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1027:20: warning: variable ‘scb_ampdu’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-3-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:504:18: warning: ‘brcmf_fws_prio2fifo’ defined but not used [-Wunused-const-variable=]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-25-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43/phy_ht.c: In function ‘b43_phy_ht_op_init’:
drivers/net/wireless/broadcom/b43/phy_ht.c:904:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-18-lee.jones@linaro.org
The function headers are either very weakly documented or not at all.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:94: warning: Function parameter or member 'reg50' not described in 'brcmf_btcoex_info'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:94: warning: Function parameter or member 'saved_regs_part2' not described in 'brcmf_btcoex_info'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:233: warning: Function parameter or member 'btci' not described in 'btcmf_btcoex_save_part1'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:253: warning: Function parameter or member 'btci' not described in 'brcmf_btcoex_restore_part1'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:273: warning: Function parameter or member 't' not described in 'brcmf_btcoex_timerfunc'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Function parameter or member 'vif' not described in 'brcmf_btcoex_set_mode'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Function parameter or member 'duration' not described in 'brcmf_btcoex_set_mode'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Excess function parameter 'cfg' description in 'brcmf_btcoex_set_mode'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-17-lee.jones@linaro.org
The function parameter is not documented and either are any of the
other functions in this source file.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c:69: warning: Function parameter or member 'c' not described in 'is_nvram_char'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-13-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:27:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_dotxstatus’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:845:6: warning: variable ‘mcl’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_b_phy_reset’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:1779:7: warning: variable ‘phy_in_reset’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_ucode_download’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:2273:23: warning: variable ‘wlc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_b_coreinit’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3176:6: warning: variable ‘sflags’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_set_chanspec’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3902:7: warning: variable ‘switchband’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_down’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5182:7: warning: variable ‘dev_gone’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_ofdm_rateset_war’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5393:5: warning: variable ‘r’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘mac80211_wlc_set_nrate’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5876:6: warning: variable ‘bcmerror’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_d11hdrs_mac80211’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:6213:7: warning: variable ‘short_preamble’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-10-lee.jones@linaro.org
Some formatting issues, some missing and some extra descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:162: warning: Function parameter or member 'oui' not described in 'brcmf_p2p_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:162: warning: Function parameter or member 'elts' not described in 'brcmf_p2p_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:181: warning: Function parameter or member 'oui' not described in 'brcmf_p2p_action_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:181: warning: Function parameter or member 'elts' not described in 'brcmf_p2p_action_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:196: warning: Function parameter or member 'query_data' not described in 'brcmf_p2psd_gas_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:210: warning: Function parameter or member 'extra_listen' not described in 'brcmf_config_af_params'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Function parameter or member 'ifp' not described in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Excess function parameter 'ndev' description in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Excess function parameter 'action' description in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'wdev' not described in 'brcmf_p2p_remain_on_channel'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'cookie' not described in 'brcmf_p2p_remain_on_channel'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1063: warning: Function parameter or member 'channel' not described in 'brcmf_p2p_act_frm_search'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1337: warning: Function parameter or member 'mac' not described in 'brcmf_p2p_gon_req_collision'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Function parameter or member 'cfg' not described in 'brcmf_p2p_ifchange'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Function parameter or member 'if_type' not described in 'brcmf_p2p_ifchange'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Excess function parameter 'mac' description in 'brcmf_p2p_ifchange'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-6-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:18:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_finalize’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:648:25: warning: variable ‘sgi’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus_complete’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:856:18: warning: variable ‘rr_retry_limit’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:855:5: warning: variable ‘antselid’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:853:41: warning: variable ‘tx_error’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:853:7: warning: variable ‘update_rate’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1037:28: warning: variable ‘tx_info’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1035:28: warning: variable ‘ini’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-5-lee.jones@linaro.org
'vif' is a function parameter which is oddly overwritten within the
function, but never read back. 'timeout' is set, but never checked.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c: In function ‘brcmf_p2p_scan_prep’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:894:31: warning: parameter ‘vif’ set but not used [-Wunused-but-set-parameter]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c: In function ‘brcmf_p2p_tx_action_frame’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1549:6: warning: variable ‘timeout’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-26-lee.jones@linaro.org
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-8-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-7-allen.cryptic@gmail.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43/phy_n.c: In function ‘b43_nphy_workarounds_rev3plus’:
drivers/net/wireless/broadcom/b43/phy_n.c:3346:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c: In function ‘b43_nphy_spur_workaround’:
drivers/net/wireless/broadcom/b43/phy_n.c:4608:4: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c:4641:4: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c: In function ‘b43_phy_initn’:
drivers/net/wireless/broadcom/b43/phy_n.c:6170:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c:6215:5: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de>
Cc: Michael Buesch <m@bues.ch>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-31-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43/phy_common.c:467: warning: Function parameter or member 'work' not described in 'b43_phy_txpower_adjust_work'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de>
Cc: Martin Langer <martin-langer@gmx.de>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <m@bues.ch>
Cc: van Dyk <kugelfang@gentoo.org>
Cc: Andreas Jaggi <andreas.jaggi@waterwave.ch>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-27-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:30:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:288: warning: Function parameter or member 'wl' not described in 'brcms_free'
drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:1127: warning: Function parameter or member 'pdev' not described in 'brcms_attach'
drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:1222: warning: Function parameter or member 'pdev' not described in 'brcms_bcma_probe'
drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:1301: warning: Function parameter or member 'work' not described in 'brcms_driver_init'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-25-lee.jones@linaro.org
Also demote a commit block header which is clearly not suitable for kerneldoc.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c: In function ‘brcmf_fweh_handle_if_event’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:131:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:36: warning: Function parameter or member 'datalen' not described in 'brcmf_fweh_queue_item'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:44: warning: Function parameter or member 'code' not described in 'brcmf_fweh_event_name'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:44: warning: Function parameter or member 'name' not described in 'brcmf_fweh_event_name'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Function parameter or member 'emsg' not described in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Function parameter or member 'data' not described in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Excess function parameter 'item' description in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Excess function parameter 'ifpp' description in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:391: warning: Function parameter or member 'packet_len' not described in 'brcmf_fweh_process_event'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-24-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c: In function ‘brcmf_fweh_handle_if_event’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:131:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-23-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43legacy/main.c: In function ‘b43legacy_interrupt_tasklet’:
drivers/net/wireless/broadcom/b43legacy/main.c:1344:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Martin Langer <martin-langer@gmx.de>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <m@bues.ch>
Cc: van Dyk <kugelfang@gentoo.org>
Cc: Andreas Jaggi <andreas.jaggi@waterwave.ch>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-18-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43/main.c: In function ‘b43_dummy_transmission’:
drivers/net/wireless/broadcom/b43/main.c:785:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/main.c: In function ‘b43_do_interrupt_thread’:
drivers/net/wireless/broadcom/b43/main.c:2017:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Martin Langer <martin-langer@gmx.de>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <m@bues.ch>
Cc: van Dyk <kugelfang@gentoo.org>
Cc: Andreas Jaggi <andreas.jaggi@waterwave.ch>
Cc: Albert Herranz <albert_herranz@yahoo.es>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-8-lee.jones@linaro.org
The 4329 throughput drops from 40.2 Mbits/sec to 190 Kbits/sec in 2G
11n mode because the commit b41c232d33 ("brcmfmac: reserve 2 credits
for host tx control path"). To fix the issue, host driver only reserves
tx control credit when there is a txctl frame is pending to send. And
we also check available credit by using "not equal to 0" instead of
"greater than 0" because tx_max and tx_seq are circled positive numbers.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: b41c232d33 ("brcmfmac: reserve 2 credits for host tx control path")
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813070017.89023-1-wright.feng@cypress.com
Clang static analysis reports this error
brcmfmac/core.c:490:4: warning: Dereference of null pointer
(*ifp)->ndev->stats.rx_errors++;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this block of code
if (ret || !(*ifp) || !(*ifp)->ndev) {
if (ret != -ENODATA && *ifp)
(*ifp)->ndev->stats.rx_errors++;
brcmu_pkt_buf_free_skb(skb);
return -ENODATA;
}
(*ifp)->ndev being NULL is caught as an error
But then it is used to report the error.
So add a check before using it.
Fixes: 91b632803e ("brcmfmac: Use net_device_stats from struct net_device")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802161804.6126-1-trix@redhat.com
When brcmf_proto_msgbuf_attach fail and msgbuf->txflow_wq != NULL,
we should destroy the workqueue.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595237765-66238-1-git-send-email-wangyufen@huawei.com
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
Set the timeout value as per cfg80211's set_power_mgmt() request. If the
requested value value is left undefined we set it to 2 seconds, the
maximum supported value.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721112302.22718-1-nsaenzjulienne@suse.de
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719111124.58167-1-grandmaster@al2klimov.de
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719110115.58085-1-grandmaster@al2klimov.de
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
In some b43 files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-6-f.suligoi@asem.it
The code in the BRCM80211 BRCMSMAC driver is using the legacy
GPIO API to to a complex check of the validity of the base of
the GPIO chip and whether it is present at all and then adding
an offset to the base of the chip.
Use the existing function to obtain a GPIO line internally
from a GPIO chip so we can use the offset directly and
modernize the code to use GPIO descriptors instead of integers
from the global GPIO numberspace.
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Frank Kao <frank.kao@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200711210150.4943-1-linus.walleij@linaro.org
The driver relies on the compatible string from DT to determine which
FW configuration file it should load. The DTS spec allows for '/' as
part of the compatible string. We change this to '-' so that we will
still be able to load the config file, even when the compatible has a
'/'. This fixes explicitly the firmware loading for
"solidrun,cubox-i/q".
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Hans deGoede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200701112201.6449-1-matthias.bgg@kernel.org
Linux 3.6 introduces TSQ which has a per socket threshold for TCP Tx
packet to reduce latency. In flow control mode, host driver enqueues skb
in hanger and TCP doesn't push new skb frees until host frees the skb when
receiving fwstatus event. So set pacing shift 8 to send them as a single
large aggregate frame to the bus layer.
43455 TX TCP throughput in different FC modes on Linux 5.4.18
sk_pacing_shift : Throughput (fcmode=0)
10: 245 Mbps
9: 245 Mbps
8: 246 Mbps
7: 246 Mbps
sk_pacing_shift : Throughput (fcmode=1)
10: 182 Mbps
9: 197 Mbps
8: 206 Mbps
7: 207 Mbps
sk_pacing_shift : Throughput (fcmode=2)
10: 180 Mbps
9: 197 Mbps
8: 206 Mbps
7: 207 Mbps
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624091608.25154-3-wright.feng@cypress.com
When USB or SDIO device got abnormal bus disconnection, host driver
tried to clean up the skbs in PSQ and TXQ (The skb's pointer in hanger
slot linked to PSQ and TSQ), so we should set the state of skb hanger slot
to BRCMF_FWS_HANGER_ITEM_STATE_FREE before freeing skb.
In brcmf_fws_bus_txq_cleanup it already sets
BRCMF_FWS_HANGER_ITEM_STATE_FREE before freeing skb, therefore we add the
same thing in brcmf_fws_psq_flush to avoid following warning message.
[ 1580.012880] ------------ [ cut here ]------------
[ 1580.017550] WARNING: CPU: 3 PID: 3065 at
drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49
brcmu_pkt_buf_free_skb+0x21/0x30 [brcmutil]
[ 1580.184017] Call Trace:
[ 1580.186514] brcmf_fws_cleanup+0x14e/0x190 [brcmfmac]
[ 1580.191594] brcmf_fws_del_interface+0x70/0x90 [brcmfmac]
[ 1580.197029] brcmf_proto_bcdc_del_if+0xe/0x10 [brcmfmac]
[ 1580.202418] brcmf_remove_interface+0x69/0x190 [brcmfmac]
[ 1580.207888] brcmf_detach+0x90/0xe0 [brcmfmac]
[ 1580.212385] brcmf_usb_disconnect+0x76/0xb0 [brcmfmac]
[ 1580.217557] usb_unbind_interface+0x72/0x260
[ 1580.221857] device_release_driver_internal+0x141/0x200
[ 1580.227152] device_release_driver+0x12/0x20
[ 1580.231460] bus_remove_device+0xfd/0x170
[ 1580.235504] device_del+0x1d9/0x300
[ 1580.239041] usb_disable_device+0x9e/0x270
[ 1580.243160] usb_disconnect+0x94/0x270
[ 1580.246980] hub_event+0x76d/0x13b0
[ 1580.250499] process_one_work+0x144/0x360
[ 1580.254564] worker_thread+0x4d/0x3c0
[ 1580.258247] kthread+0x109/0x140
[ 1580.261515] ? rescuer_thread+0x340/0x340
[ 1580.265543] ? kthread_park+0x60/0x60
[ 1580.269237] ? SyS_exit_group+0x14/0x20
[ 1580.273118] ret_from_fork+0x25/0x30
[ 1580.300446] ------------ [ cut here ]------------
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624091608.25154-2-wright.feng@cypress.com
commit 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
adds a reset function to recover firmware trap for PCIe bus. This commit
adds an implementation for SDIO bus.
Upon SDIO firmware trap, do below:
- Remove the device
- Reset hardware
- Probe the device again
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622144851.165248-1-chi-hsien.lin@cypress.com
Ignore FW event if the event's BSSID is different form the BSSID of the
currently connected AP. Check interface state is connected or not, if
state is not connected that can ignore link down event.
Signed-off-by: Able Liao <Able.Liao@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-4-chi-hsien.lin@cypress.com
Current brcmf_link_down() always call cfg80211_disconnected() with
locally_generated=1, which is not always the case. Add event source
argument on link down handler and set locally_generated based on the
real trigger.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-3-chi-hsien.lin@cypress.com
Unable to change back to visiable SSID because there is
no disable hidden ssid routine.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-2-chi-hsien.lin@cypress.com
Commit 4905432b28b7 ("brcmfmac: Fix P2P Group Formation failure via Go-neg
method") did not initialize requested_dwell properly, resulting in an
always-false dwell time overflow check. Fix it by setting the correct
requested_dwell value.
Fixes: 4905432b28b7 ("brcmfmac: Fix P2P Group Formation failure via Go-neg method")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joseph Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-7-chi-hsien.lin@cypress.com
This patch move the credit map setting to right place to avoid
brcmf_fws_return_credits() return without setting the credit map.
It fix the thoughput zero stalls issue in softAP mode when STA
using PM 1 mode.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-6-chi-hsien.lin@cypress.com
There is a mismatch of tx status flag values between host and firmware.
It makes the host mistake the flags and have incorrect behavior of credit
returns. So update the flags to sync with the firmware ones.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-5-chi-hsien.lin@cypress.com
It is observed that sometimes when sdiod is low in tx credits in low
rssi scenarios, the data path consumes all sdiod rx all credits and
there is no sdiod rx credit available for control path causing host
and card to go out of sync resulting in link loss between host and
card. So in order to prevent it some credits are reserved for control
path.
Note that TXCTL_CREDITS can't be larger than the firmware default
credit update threshold 2; otherwise there will be a deadlock for both
side waiting for each other.
Signed-off-by: Amar Shankar <amsr@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-4-chi-hsien.lin@cypress.com
In wifi firmware, max length of IOCTL/IOVAR buffer size is 8192.
Increase the message buffer max size same as wifi firmware for control
packets so return buffers can come back.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-3-chi-hsien.lin@cypress.com
Current credit borrowing allows only the access category BE to
borrow the credits. This change is to fix the credit borrowing
logic, to make borrowing available for all access categories
and also to borrow only from the lower categories. This fixes WFA
802.11n certs 5.2.27 failures.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-2-chi-hsien.lin@cypress.com
Bss info flag definition need to be fixed from 0x2 to 0x4
This flag is for rssi info received on channel.
All Firmware branches defined as 0x4 and this is bug in brcmfmac.
Signed-off-by: Prasanna Kerekoppa <prasanna.kerekoppa@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-6-wright.feng@cypress.com
The firmware state machines are not fully suitable for concurrent
station interface support, it may hit unexpected error if we have 2
different SSIDs and the roaming scenarios concurrently.
To avoid the bad user-experience if this is not fully validated, we
dis-allow user to create two concurrent station interfaces.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-5-wright.feng@cypress.com
brcmfmac host driver makes SDIO bus sleep and stops SDIO watchdog if no
pending event or data. As a result, host driver does not poll firmware
console buffer before buffer overflow, which leads to missing firmware
logs. We should not stop SDIO watchdog if console_interval is non-zero
in debug build.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-4-wright.feng@cypress.com
When host driver retrieves mac addresses from dongle, driver copies memory
from drvr->mac to perm_addr. But at the moment, drvr->mac is all zero
array which causes permanent MAC address in wiphy is all zero as well.
To fix this, we set drvr->mac before setting perm_addr.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-3-wright.feng@cypress.com
To truncate the additional bytes, if extra bytes have been received.
Current code only have a warning and proceed without handling it.
But in one of the crash reported by DVT, these causes the
crash intermittently. So the processing is limit to the skb->len.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-2-wright.feng@cypress.com
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Set MES watermark size to 0x50 for 43012. It fixes SDIO bus hang issue
when running at high throughput.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-6-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4354/4356 SDIO.
Also enable and configure F1 MesBusyCtrl. It would resolve random driver
crash issue.
Signed-off-by: Frank Kao <frank.kao@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-4-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes for 4373. It fixes DMA error while having
UDP bi-directional traffic. Also use a defined F1 MesBusyCtrl value.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-2-chi-hsien.lin@cypress.com
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43legacy did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43legacy will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.net
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43 did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43 will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Reported-and-tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-2-Larry.Finger@lwfinger.net
All macro names for SDIO device IDs are prefixed by vendor name to which
device ID belongs. So for consistency add Broadcom string vendor prefix to
all Cypress macro names as they belong to SDIO Broadcom vendor ID.
Change also Cypress 43012 value from decimal do hexadecimal notation to be
consistent with all other values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-11-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An incorrect value of use_fwsup is set for 4-way handshake offload for
WPA//WPA2-PSK, caused by commit 3b1e0a7bdf ("brcmfmac: add support for
SAE authentication offload"). It results in missing bit
BRCMF_VIF_STATUS_EAP_SUCCESS set in brcmf_is_linkup() and causes the
failure. This patch correct the value for the case.
Also setting bit BRCMF_VIF_STATUS_EAP_SUCCESS for SAE offload case in
brcmf_is_linkup() to fix SAE offload failure.
Fixes: 3b1e0a7bdf ("brcmfmac: add support for SAE authentication offload")
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589277788-119966-1-git-send-email-chi-hsien.lin@cypress.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1785:5-8:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508074351.19193-1-yanaijie@huawei.com
Fix sparse warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2206:5:
warning: symbol 'brcmf_p2p_get_conn_idx' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508013249.95196-1-chenzhou10@huawei.com
When plumbing rxiv for (GTK) keys, current code does not use seq/seq_len
when present nor set iv_initialized for iovar wsec_key. This could
result in missing broadcast traffic after GTK rekey. The fix is setting
iv_initialized and using seq/seq_len for iovar wsec_key.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-4-git-send-email-wright.feng@cypress.com
The driver sends an action frame down and waits for dwell time to be
completed or aborted before sending out the next action frame.
Driver issues "scan abort" to cancel the current time slot, but this
doesn't have any effect because, we are not using scan engine for
sending action frame.
Fix is to use "actframe_abort" to cancels the current action frame.
Signed-off-by: Ryohei Kondo <ryohei.kondo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-3-git-send-email-wright.feng@cypress.com
Host driver parses and sets security params into FW passed by
supplicant. This has to be done after reiniting interface in the
firmware.
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-2-git-send-email-wright.feng@cypress.com
802.1d defines 0,3 for BE and 1,2 for BK. In pcie dongles, 0 & 3 are
mapped to 0 and 1,2 are mapped to 1. This change corrects this mapping,
so that BE & BK are given access precedence accordingly by pcie dongles.
Signed-off-by: Pramod Prakash <pramod.prakash@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-3-git-send-email-chi-hsien.lin@cypress.com
In WLAN, priority among various access categories of traffic is
always set by the AP using WMM parameters and this may not always
follow the standard 802.1d priority.
In this change, priority is adjusted based on the AP WMM params
received as part of the Assoc Response and the same is later used
to map the priority of all incoming traffic.
In a specific scenario where EDCA parameters are configured to be same
for all ACs, use the default FW priority definition to avoid queuing
packets of all ACs to the same priority queue.
This change fixes the following 802.11 certification tests:
* 11n - 5.2.31 ACM Bit Conformance test
* 11n - 5.2.32 AC Parameter Modification test
* 11ac - 5.2.33 TXOP Limit test
Signed-off-by: Saravanan Shanmugham <saravanan.shanmugham@cypress.com>
Signed-off-by: Justin Li <justin.li@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-2-git-send-email-chi-hsien.lin@cypress.com
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJetAhAAAoJEG4XJFUm622bADEH/A1OjAD3H1iZyTmXHP4T7yZe
TKJ+9I6B3BDR1czUTm+kUhrgBDNpdLLtu+b+5QXfpPLrtZ0FF/zjuazgueyqQpZ1
zudj+rG72njHpU0RKtO7wIBrCtckLPV0be+3026hztatJmJ7XQ9FvsanFPPsrrNv
0lh8E8kDUSynOW2me8FW1GBgDkGaBaicAs4FSjwNJC31Wo/VN5m9gEFkGpT1VJWP
l0xeEQ/N2mknQVuTR4CuMT9VJ0SNlJrLZpBVAqkmc170c3pKChl3LTNCnP925ye9
Nfqw2sQKgUPJKRbZR5wZTphGuu4krFv0ldWCvb0oFtZlCLIkiOz6+AA7b33oV2A=
=7ewK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is dead for more than 10 years. Remove it.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/b43/pio.c:768:10-25: WARNING: Comparison
of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113311.41026-1-yanaijie@huawei.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/b43/phy_n.c:5510:19-32: WARNING:
Comparison of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113300.40895-1-yanaijie@huawei.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:1060:6-12:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113357.41422-1-yanaijie@huawei.com
It was observed that P2P Cert. 5.1.19: DEVUT responds to Service
Discovery request failed due to DUT did not send GAS Comeback Response
after receiving request from test bed P2P peer. To fix this issue,
we need to add P2P Action Frame retry delay to enhance P2P connection
under VSDB and noisy environment, since the peer can be in other
channels under VSDB.
Signed-off-by: Justin Li <Justin.Li@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-4-git-send-email-wright.feng@cypress.com
P2P group formation fails since either peer is not able to send go-neg
confirm or dut is not able to send go-neg response. To fix this, retry
limit should be increased and dwell time check should be added.
Signed-off-by: Joseph Chuang <joseph.chuang@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-3-git-send-email-wright.feng@cypress.com
With RSDB feature, firmware is able to support two P2P-AGO or two
P2P-GC at the same time. So we add the second p2p connection type
to map to the second P2P connection bsscfg.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-2-git-send-email-wright.feng@cypress.com
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
In doing this, make brcmf_debugfs_add_entry() return void as no one was
even paying attention to the return value.
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafał Miłecki" <rafal@milecki.pl>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200429101526.GA2094124@kroah.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:2359:6-40:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426094053.23132-1-yanaijie@huawei.com
Miracast Certification clause 6.1.2 may fail if there is no WFD IE in
p2p assoc response. This change allows WFD IE to be added to p2p assoc
response.
Related WFA certification:
6.1.2 P-SnUT operating as a Group Owner accepts a WFD Session with a
Reference Source
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Ryohei Kondo <ryohei.kondo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-6-git-send-email-chi-hsien.lin@cypress.com
P2p spec mentioned that the p2p device address should be the globally
administered address with locally administered bit set. Therefore,
follow this guideline by default.
When the primary interface is set to a locally administered address, the
locally administered bit cannot be set again. Generate a random locally
administered address for this case.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-5-git-send-email-chi-hsien.lin@cypress.com
Send p2p presence response from the p2p interface address instead
of the p2p device address. This is needed for p2p cert 6.1.9 to pass.
Signed-off-by: Madhan Mohan R <MadhanMohan.R@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-4-git-send-email-chi-hsien.lin@cypress.com
The firmware does not respond ARP request and causes ping failure with
following steps:
1. Bring up interface
ifconfig wlan0 up or start wpa_supplicant
2. Set the IP address
ifconfig wlan0 192.168.100.10
3. Bring down interface or
ifconfig wlan0 down or kill wpa_supplicant
4. Bring up interface again and set the same IP address
5. Connect to AP(192.168.100.1) and ping to AP will be failed.
FMAC clears arp_hostip when bringing down the interface, but not set it
back if setting the same IP address. We are able to see the IP address
in interface info(inconfig wlan0) but the ping still cannot work because
the firmware ARP offload does not respond the ARP request.
Because of that, we remove "arp_hostip_clear" from function
"brcmf_netdev_stop"
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-3-git-send-email-chi-hsien.lin@cypress.com
When starting station mode on wlan0 and AP mode on wlan1, the apsta will
be disabled and cause data stall on wlan0(station). The apsta feature
with MCHAN(Multi-Channel Concurrent) or RSDB(Real Simultaneous
Dual-Band) can make STA+AP work on two bands concurrently.
Because of that, we keep apsta enabled if firmware supports MCHAN or
RSDB features
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-2-git-send-email-chi-hsien.lin@cypress.com
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
