Commit 60268b0e82 ("hwmon: (amd_energy) modify the visibility of
the counters") restricted visibility of AMD energy counters to work
around a side-channel attack using energy data to determine which
instructions are executed. The attack is described in 'PLATYPUS:
Software-based Power Side-Channel Attacks on x86'. It relies on quick
and accurate energy readings.
This change made the counters provided by the amd_energy driver
effectively unusable for non-provileged users. However, unprivileged
read access is the whole point of hardware monitoring attributes.
An attempt to remedy the situation by limiting and randomizing access
to chip registers was rejected by AMD. Since the driver is for all
practical purposes unusable, remove it.
Cc: Naveen Krishna Chatradhi <nchatrad@amd.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hardware monitoring sysfs attributes are used and displayed by unrestricted
userspace applications. Standard attributes therefore have to be world
readable, since otherwise those userspace applications would either have
to run as super-user or display an error. None of those makes sense.
Clarify the expected scope of attribute access in the ABI document.
Cc: Naveen Krishna Chatradhi <nchatrad@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add pmbus driver support for Maxim MAX15301 InTune Automatically
Compensated Digital PoL Controller with Driver and PMBus Telemetry
Even though the specification does not specifically mention it,
extensive empirical testing has revealed that auto-detection of
limit-registers will fail in a random fashion unless the delay
parameter is set to above about 80us. The default delay is set
to 100us to include some safety margin.
This patch is tested on a Flex BMR461 converter module.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210419101251.24840-1-erik.rosen@metormote.com
[groeck: Added rationale for delay to driver header]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for these devices:
- YH-5151E - the PDU
- YM-2151E - the PSU
The device datasheet says that the devices support PMBus 1.2, but in my
testing, a lot of the commands aren't supported and if they are, they
sometimes behave strangely or inconsistently. For example, writes to the
PAGE command requires using PEC, otherwise the write won't work and the
page won't switch, even though, the standard says that PEC is optional.
On the other hand, writes to SMBALERT don't require PEC. Because of
this, the driver is mostly reverse engineered with the help of a tool
called pmbus_peek written by David Brownell (and later adopted by my
colleague Jan Kundrát).
The device also has some sort of a timing issue when switching pages,
which is explained further in the code.
Because of this, the driver support is limited. It exposes only the
values that have been tested to work correctly.
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210414080019.3530794-1-kubernat@cesnet.cz
[groeck: Fixed up "missing braces around initializer" from 0-day]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These are "all-in-one" CPU liquid coolers that can be monitored and
controlled through a proprietary USB HID protocol.
While the models have differently sized radiators and come with varying
numbers of fans, they are all indistinguishable at the software level.
The driver exposes fan/pump speeds and coolant temperature through the
standard hwmon sysfs interface.
Fan and pump control, while supported by the devices, are not currently
exposed. The firmware accepts up to 61 trip points per channel
(fan/pump), but the same set of trip temperatures has to be maintained
for both; with pwmX_auto_point_Y_temp attributes, users would need to
maintain this invariant themselves.
Instead, fan and pump control, as well as LED control (which the device
also supports for 9 addressable RGB LEDs on the CPU water block) are
left for existing and already mature user-space tools, which can still
be used alongside the driver, thanks to hidraw. A link to one, which I
also maintain, is provided in the documentation.
The implementation is based on USB traffic analysis. It has been
runtime tested on x86_64, both as a built-in driver and as a module.
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Link: https://lore.kernel.org/r/20210319045544.416138-1-jonas@protocubo.io
[groeck: Removed unnecessary spinlock.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adds support for reading the critical values of the temperature sensors
and the rail sensors (voltage and current) once and caches them. Updates
the naming of the constants following a more clear scheme. Also updates
the documentation and fixes some typos. Updates is_visible and ops_read
functions to be more readable.
The new sensors output of a Corsair HX850i will look like this:
corsairpsu-hid-3-1
Adapter: HID adapter
v_in: 230.00 V
v_out +12v: 12.14 V (crit min = +8.41 V, crit max = +15.59 V)
v_out +5v: 5.03 V (crit min = +3.50 V, crit max = +6.50 V)
v_out +3.3v: 3.30 V (crit min = +2.31 V, crit max = +4.30 V)
psu fan: 0 RPM
vrm temp: +46.2°C (crit = +70.0°C)
case temp: +39.8°C (crit = +70.0°C)
power total: 152.00 W
power +12v: 108.00 W
power +5v: 41.00 W
power +3.3v: 5.00 W
curr +12v: 9.00 A (crit max = +85.00 A)
curr +5v: 8.31 A (crit max = +40.00 A)
curr +3.3v: 1.62 A (crit max = +40.00 A)
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/YFNg6vGk3sQmyqgB@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds a hwmon driver for the AHT10 Temperature and
Humidity sensor. It has a maximum sample rate, as the datasheet
states that the chip may heat up if it is sampled more than once
every two seconds.
Has been tested a to work on a raspberrypi0w
Signed-off-by: Johannes Cornelis Draaijer (datdenkikniet) <jcdra1@gmail.com>
Link: https://lore.kernel.org/r/20210107194014.GA88780@desktop
[groeck: dropped AHT10_ADDR (unused) and use AHT10_MEAS_SIZE where
appropriate; dropped change log]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This deletes the ABx500 hwmon driver, the only supported
variant being the AB8500.
This driver has been replaced by generic frameworks. By
inspecting the abx500 sysfs files we see that it contains
things such as temp1_max, temp1_max_alarm, temp1_max_hyst,
temp1_max_hyst_alarm, temp1_min, temp1_min_alarm.
It becomes obvious that the abx500.c is a reimplementation
of thermal zones. This is not very strange as the generic
thermal zones were not invented when this driver was merged
so people were rolling their own.
The ab8500.c driver contains conversion tables for handling
a thermistor on ADC channels AUX1 and AUX2.
I managed to replace the functionality of the driver with:
- Activation of the ntc_thermistor.c driver,
CONFIG_SENSORS_NTC_THERMISTOR
- Activation of thermal zones, CONFIG_THERMAL
- In the device tree, connecting the NTC driver to the
processed IIO channels from the AB8500 GPADC ADC forming
two instances of NTC sensors.
- Connecting the two NTC sensors to a "chassis" thermal zone
in the device tree and setting that to hit the CPU frequency
at 50 degrees celsius and do a critical shutdown at 70
degrees celsius, deploying a policy using the sensors.
After talking to the original authors we concluded that the
driver was never properly parameterized in production so
what we now have in the device tree is already puts the
thermistors to better use than what the hwmon driver did.
The two remaining channels for two battery temperatures is
already handled in the charging algorithms but can be
optionally extended to thermal zones as well if we want
these to trigger critical shutdown for the platform.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201221125521.768082-1-linus.walleij@linaro.org
[groeck: Removed documentation and fixed up Makefile, Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit b722d7b9e4da ("hwmon: (pmbus) Driver for Delta power supplies
Q54SJ108A2") provides new documentation for DELTA Q54SJ108A2NC* drivers,
but the title underline was too short.
make htmldocs warns:
Documentation/hwmon/q54sj108a2.rst:4: WARNING: Title underline too short.
Adjust the title underline to the correct length.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20201207152658.32444-1-lukas.bulwahn@gmail.com
[groeck: Adjust subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2992 is a rail-to-rail system monitor that
measures current, voltage, and power of two supplies.
Two ADCs simultaneously measure each supply’s current.
A third ADC monitors the input voltages and four
auxiliary external voltages.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the pmbus driver for the STMicroelectronics pm6764 voltage regulator.
the output voltage use the MFR_READ_VOUT 0xD4
vout value returned is linear11
Signed-off-by: Charles Hsu <hsu.yungteng@gmail.com>
[groeck: Fixed various compile errors; marked pm6764tr_of_match __maybe_unused]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Corsair digital power supplies of the series RMi, HXi and AXi include
a small micro-controller with a lot of sensors attached. The sensors can
be accessed by an USB connector from the outside.
This micro-controller provides the data by a simple proprietary USB HID
protocol. The data consist of temperatures, current and voltage levels,
power usage, uptimes, fan speed and some more. It is also possible to
configure the PSU (fan mode, mono/multi-rail, over current protection).
This driver provides access to the sensors/statistics of the RMi and HXi
series power supplies. It does not support configuring these devices,
because there would be many ways to misconfigure or even damage the PSU.
This patch adds:
- hwmon driver corsair-psu
- hwmon documentation
- updates MAINTAINERS
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/20201027131710.GA253280@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only action currently performed in pmbus_do_remove() is removing the
debugfs hierarchy. We can schedule a devm action at probe time and remove
pmbus_do_remove() entirely from all pmbus drivers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201026105352.20359-1-brgl@bgdev.pl
[groeck: Removed references to pmbus_do_remove from documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
.../Documentation/hwmon/mp2975.rst:25: WARNING: Unexpected indentation.
.../Documentation/hwmon/mp2975.rst:27: WARNING: Block quote ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst:69: WARNING: Unexpected indentation.
.../Documentation/hwmon/mp2975.rst:70: WARNING: Block quote ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst:72: WARNING: Bullet list ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst: WARNING: document isn't included in any toctree
List blocks should have blank lines before and after them,
in order to be properly parsed.
Fixes: 4beb7a028e9f ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/b02f98d886ab1f5af233f8999c7a15529fc52cdc.1603791716.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull hwmon updates from Guenter Roeck:
"New driver and chip support:
- Moortec MR75203 PVT controller
- MPS Multi-phase mp2975 controller
- ADM1266
- Zen3 CPUs
- Intel MAX 10 BMC
Enhancements:
- Support for rated attributes in hwmon core
- MAX20730:
- Device monitoring via debugfs
- VOUT readin adjustment vie devicetree bindings
- LM75:
- Devicetree support
- Regulator support
- Improved accumulationm logic in amd_energy driver
- Added fan sensor to gsc-hwmon driver
- Support for simplified I2C probing
Various other minor fixes and improvements"
* tag 'hwmon-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (64 commits)
hwmon: (pmbus/max20730) adjust the vout reading given voltage divider
dt-bindings: hwmon: max20730: adding device tree doc for max20730
hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller
hwmon: Add DT bindings schema for PVT controller
dt-bindings: hwmon: Add the +vs supply to the lm75 bindings
dt-bindings: hwmon: Convert lm75 bindings to yaml
docs: hwmon: (ltc2945) update datasheet link
hwmon: (mlxreg-fan) Fix double "Mellanox"
hwmon: (pmbus/max20730) add device monitoring via debugfs
hwmon: (pmbus/max34440) Fix OC fault limits
hwmon: (bt1-pvt) Wait for the completion with timeout
hwmon: (bt1-pvt) Cache current update timeout
hwmon: (bt1-pvt) Test sensor power supply on probe
hwmon: (lm75) Add regulator support
hwmon: Add hwmon driver for Intel MAX 10 BMC
dt-bindings: Add MP2975 voltage regulator device
hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller
hwmon: (tmp513) fix spelling typo in comments
hwmon: (amd_energy) Update driver documentation
hwmon: (amd_energy) Improve the accumulation logic
...
This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC
chip connects to a set of sensor chips to monitor current, voltage,
thermal and power of different components on board. The BMC firmware is
responsible for sensor data sampling and recording in shared registers.
Host driver reads the sensor data from these shared registers and
exposes them to users as hwmon interfaces.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1600669071-26235-3-git-send-email-yilun.xu@intel.com
[groeck: Adjusted subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp295 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a dual-loop, digital, multi-phase controller.
This device:
- Supports two power rail.
- Provides 8 pulse-width modulations (PWMs), and can be configured up
to 8-phase operation for rail 1 and up to 4-phase operation for rail
2.
- Supports two pages 0 and 1 for telemetry and also pages 2 and 3 for
configuration.
- Can configured VOUT readout in direct or VID format and allows
setting of different formats on rails 1 and 2. For VID the following
protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
10-mV DAC, IMVP9 mode with 5-mV DAC.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20200926204957.10268-2-vadimp@nvidia.com
[groeck: Cleaned up a couple of error returns; fixed up API changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some drives, reading the drive temperature resets the drive's
spin-down timer. If the drive temperature is read too often, affected
drives will never spin down. Add this information as usage note to
the driver documentation.
Reported-by: Peter Sulyok <peter@sulyok.net>
Cc: Peter Sulyok <peter@sulyok.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the hardware monitoring controller of the sl28cpld board
management controller. This driver is part of a multi-function device.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the possibility for reading pwm values.
These can not be read if the device is controlled via
fan_target or a fan curve and will return an error in
this case. Since an error is expected, this adds some
rudimentary error handling.
Changes:
- add CTL_GET_FAN_PWM and use it via get_data
- pwm returns -ENODATA if the device returns error 0x12
- fan_target now returns -ENODATA when the driver is
started or a pwm value is set.
- add ccp_get_errno to determine errno from device error.
- get_data now has a parameter to determine whether
to read one or two bytes of data.
- update documentation
- fix missing surname in MAINTAINERS
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
