Drivers need to report the number of transmission attempts for each rate
as well as to terminate the rate array with -1. The in-kernel datapath
of hwsim simulates a perfect medium, therefore the driver only needs to
report that the first transmission attempt was sucessfully completed at
the most favorable rate.
Rate control is working again for this driver. Tested mesh mode with
minstrel.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some sdio host controllers do not support real in band interrupt.
Software polling mode as a replacement is not fast enough for
high throughput and new features. Also some in band interrupts
do not support host wake up on embedded platform even when they
are real physical interrupts. Therefore out of band (oob)
interrupt mechanism is implemented for these scenarios.
To provide oob irq number and flags used for irq registration in
brcmfmac, a platform device contains irq resource must be
registered in board specific code.
Here is an example of platform device structure:
struct resource brcmf_sdio_res[] = {
{
.start = GPIO_BRCMF_SDIO_OOB_NUM,
.end = GPIO_BRCMF_SDIO_OOB_NUM,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
}
};
struct platform_device brcmf_sdio_device = {
.name = "brcmf_sdio_pd",
.id = -1,
.num_resources = ARRAY_SIZE(brcmf_sdio_res),
.resource = brcmf_sdio_res,
};
Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For out of band interrupt which is going to be introduced shortly,
the interrupt register function must be called after firmware is
downloaded. This patch moves it from brcmf_sdbrcm_probe to
brcmf_sdbrcm_bus_init.
Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bus state should be the correct flag for bus status. Use it instead
of result from previous function call for backplane clock switch.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_sdbrcm_isr doesn't access to the dongle through SDIO bus.
Stop releasing and claiming host in irq handler to eliminate
any potential risk.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device. The latter needs to be registered
first.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device. The latter needs to be registered
first.
Compile-tested only.
Reported-by: Cesare Leonardi <celeonar@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFCSR is only used in rt2800. For other chipsets, the debug struct
for rfcsr should be zeroed, which isn't be an issue, since the code
can now cope with that.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow a register to be unspecified, therefore not creating its debugfs
file entry.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"oui_type" in structure "ieee_types_vendor_header" is not used separately,
so include it in "oui" array. Now complete oui will be compared fixing
following warnings.
drivers/net/wireless/mwifiex/sta_ioctl.c:1410 mwifiex_set_gen_ie_helper()
error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/sta_ioctl.c:1435 mwifiex_set_gen_ie_helper()
error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1177 mwifiex_update_bss_desc_with_ie()
error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1185 mwifiex_update_bss_desc_with_ie()
error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a cut and paste mistake, sizeof(struct mib_local) was intended
instead of sizeof(struct mib_phy). The call to at76_get_mib() uses
sizeof(struct mib_local) correctly, although I changed that to
sizeof(*m) for style reasons after discussion with some of the wireless
maintainers.
The current code works fine because mib_phy structs are larger than
mib_local structs. But we may as well clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This doesn't make any sense. Init it from the transport instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There are various problems happened on 5GHz band not observed on
2.4 GHz (microcode errors, queue stuck, etc... ) . Also roaming
between 5GHz AP and 2GHz does not work very well. To workaround
the problems add option to disable 5GHz support. This will help
on environments where APs are dual-band, and devices will not try
to associate on band where issues happen.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Also remove a debug print when allocation error occurred.
The kernel will complain anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When bluetooth coex is active and certain condition matched,
driver need to decide should the tx power been reduce or not.
Adding the logic to manage it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Do not assume we have our subsystem including this for us,
at least for older kernels this is not true. Lets just be
explicit about this requirement for the usage of wake_up().
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the GPIO/LED settings to be configured by the
EEPROM if present, and only sets the default values (LED outputs
for link/activity) when an EEPROM is not detected.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only a write is necessary to clear the interrupt status, and we
don't use the value from the preceding read operation. This
patch eliminates the unnecessary read.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines PHY_INT_SRC_CLEAR_ALL to replace the value 0xffff
in order to be more self-documenting.
This patch should make no functional change, it is purely cosmetic.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin says:
--------------------
There are mostly bugfixes here.
I hope to merge some more patches by 3.5, in particular
vlan support fixes are waiting for Eric's ack,
and a version of tracepoint patch might be
ready in time, but let's merge what's ready so it's testable.
This includes a ton of zerocopy fixes by Jason -
good stuff but too intrusive for 3.4 and zerocopy is experimental
anyway.
virtio supported delayed interrupt for a while now
so adding support to the virtio tool made sense
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO pins select which sub bus is connected to the master.
Initially tested with an sn74cbtlv3253 switch device wired into the
MDIO bus.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a somewhat generic framework for MDIO bus
multiplexers. It is modeled on the I2C multiplexer.
The multiplexer is needed if there are multiple PHYs with the same
address connected to the same MDIO bus adepter, or if there is
insufficient electrical drive capability for all the connected PHY
devices.
Conceptually it could look something like this:
------------------
| Control Signal |
--------+---------
|
--------------- --------+------
| MDIO MASTER |---| Multiplexer |
--------------- --+-------+----
| |
C C
h h
i i
l l
d d
| |
--------- A B ---------
| | | | | |
| PHY@1 +-------+ +---+ PHY@1 |
| | | | | |
--------- | | ---------
--------- | | ---------
| | | | | |
| PHY@2 +-------+ +---+ PHY@2 |
| | | |
--------- ---------
This framework configures the bus topology from device tree data. The
mechanics of switching the multiplexer is left to device specific
drivers.
The follow-on patch contains a multiplexer driven by GPIO lines.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add of_mdio_find_bus() which allows an mii_bus to be located given its
associated the device tree node.
This is needed by the follow-on patch to add a driver for MDIO bus
multiplexers.
The of_mdiobus_register() function is modified so that the device tree
node is recorded in the mii_bus. Then we can find it again by
iterating over all mdio_bus_class devices.
Because the OF device tree has now become an integral part of the
kernel, this can live in mdio_bus.c (which contains the needed
mdio_bus_class structure) instead of of_mdio.c.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent changes for how we compute the skb truesize it occurs to me
we are probably going to have a lot of calls to skb_end_pointer -
skb->head. Instead of running all over the place doing that it would make
more sense to just make it a separate inline skb_end_offset(skb) that way
we can return the correct value without having gcc having to do all the
optimization to cancel out skb->head - skb->head.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some RNDIS devices include a bogus CDC Union descriptor pointing
to non-existing interfaces. The RNDIS code is already prepared
to handle devices without a CDC Union descriptor by hardwiring
the driver to use interfaces 0 and 1, which is correct for the
devices with the bogus descriptor as well. So we can reuse the
existing workaround.
Cc: Markus Kolb <linux-201011@tower-net.de>
Cc: Iker Salmón San Millán <shaola@esdebian.org>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: 655387@bugs.debian.org
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a bug fix for an "interface fails to load" issue.
The issue occurs when bnx2x driver loads after UNDI driver was previously
loaded over the chip. In such a scenario the UNDI driver is loaded and operates
in the pre-boot kernel, within its own specific host memory address range.
When the pre-boot stage is complete, the real kernel is loaded, in a new and
distinct host memory address range. The transition from pre-boot stage to boot
is asynchronous from UNDI point of view.
A race condition occurs when UNDI driver triggers a DMAE transaction to valid
host addresses in the pre-boot stage, when control is diverted to the real
kernel. This results in access to illegal addresses by our HW as the addresses
which were valid in the preboot stage are no longer considered valid.
Specifically, the 'was_error' bit in the pci glue of our device is set. This
causes all following pci transactions from chip to host to timeout (in
accordance to the pci spec).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PFC stats are only tabulated when PFC is enabled. However in IEEE
mode the ieee_pfc pfc_tc bits were not checked and the calculation
was aborted.
This results in statistics not being reported through ethtool and
possible a false Tx hang occurring when receiving pause frames.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the REQ and GNT bit in the eeprom control register (EECD).
This is required if the eeprom is to be accessed with auto read
EERD register.
After a cold reset this doesn't matter but if PBIST MAC test was
executed before booting, the register was left in a dirty state
(the 2 bits where set), which caused the read operation to time out
and returning 0.
Reference (page 312):
http://download.intel.com/design/network/manuals/316080.pdf
Reported-by: Aleksandar Igic <aleksandar.igic@dektech.com.au>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Like other supported (igp) PHYs, the driver needs to be able to force the
master/slave mode on 82577. Since the code is the same as what already
exists in the code flow for igp PHYs, move it to a new function to be
called for both flows.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb and ixgbe incorrectly call netdev_tx_reset_queue() from
i{gb|xgbe}_clean_tx_ring() this sort of works in most cases except
when the number of real tx queues changes. When the number of real
tx queues changes netdev_tx_reset_queue() only gets called on the
new number of queues so when we reduce the number of queues we risk
triggering the watchdog timer and repeated device resets.
So this is not only a cosmetic issue but causes real bugs. For
example enabling/disabling DCB or FCoE in ixgbe will trigger this.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: John Bishop <johnx.bishop@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updates the link flow control configuration so that we
correctly set the link flow control settings for DCB. Previously we would
have to call the fc_enable call 8 times, once for each packet buffer. If
we move that logic into the fc_enable call itself we can avoid multiple
unnecessary register writes.
This change also corrects an issue in which we were only shifting the water
marks for 82599 parts by 6 instead of 10. This was resulting in us only
using 1/16 of the packet buffer when flow control was enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
