Be more careful about the state of pointers during tear-down.
The "pppoe_dev" field can only be looked at safely while holding socket locks.
This subsequently allows for the flush_lock to be killed.
We depend on the PPPOX_CONNECTED state to tell us that that those fields are
valid, so whoever clears that state (pppox_unbind_sock()) is responsible for
the dev_put() call.
We also have to ensure that we delete_item() on all sockets before they are
cleaned up.
The need for these changes has been exposed by scenarios wherein namespace
bindings of ethernet devices change while there are ongoing PPPoE sessions,
which resulted in oopses due to unusual socket connection termination paths,
exposing these issues.
Signed-off-by: Michal Ostrowski <mostrows@gmail.com>
Reviewed-by: Cyril Gorcunov <gorcunov@gmail.com>
Reported-by: Denys Fedoryschenko <denys@visp.net.lb>
Tested-by: Denys Fedoryschenko <denys@visp.net.lb>
PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch). This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired. The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.
The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses to NVM and PHY/CSR registers on ICHx/PCH-based parts are protected
from concurrent accesses with a mutex that is acquired when the access is
initiated and released when the access has completed. However, the two
types of accesses should not be protected by the same mutex because the
driver may have to access the NVM while already holding the mutex over
several consecutive PHY/CSR accesses which would result in livelock.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike previous ICHx-based parts, the PCH-based parts (82577/82578) require
LPLU (Low Power Link Up, or "reverse auto-negotiation") to be configured in
the PHY rather than the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some conditions (e.g. when AMT is enabled on the system), it is possible
to take an extended period of time to for the driver to acquire the sw/fw/hw
hardware semaphore used to protect against concurrent access of a shared
resource (e.g. PHY registers). This could cause PHY registers to not get
configured properly resulting in link issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performing a dummy read of the PHY Wakeup Control (WUC) register clears the
wakeup enable bit set by an PHY reset. If this bit remains set, link
problems may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a memory leak which occurs while changing the ring size
while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a memory leak that occurs when you resize the rings via
the ethtool -G option while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing ring sizes while the interface was down was causing a double
allocation of the receive and transmit rings. This issue is amplified when
there are multiple rings enabled. To prevent this we need to add an
additional check which will just update the ring counts when the interface
is not up and skip the allocation steps.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify bonding hash transmit policies to use the psource MAC address of
the packet instead of the MAC address configured for the bonding device.
The old sitation conflicts with the documentation.
Signed-off-by: Jasper Spaans <spaans@fox-it.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DM9000B revision ID is 0x1A, not 0x1B as set in the curernt
dm9000.h header.
Fix bug reported by Paolo Zebelloni.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8110SC rev d chip on our board shows a regression which the 8110SB chip
did not have. When inbound traffic is overflowing the receive descriptor queue,
"holes" in the ring buffer may occur which lead to a hangup until the buffer
is filled again. The packets are than completely processed, but the ring
remains porous and no packets are processed until the next overflow. Setting
the interface down and up can fix the problem temporary from userspace.
For some reason we don't know, this behaviour is not occuring if the RxVlan
bit for hardware VLAN untagging is set. There is another "Work around for
AMD plateform" in the current code which checks the VLAN status
word in receive descriptors, but does never come to effect when hardware
VLAN support is enabled. We assume that this is a bug in the chip.
The following patch fixes the problem. Without the patch we could reproduce
the hang within minutes (given other devices also generating lots of
interrupts), without we couldn't reproduce within a few days of long term
testing.
This version contains minor style adjustments and is sent with mutt which
will hopefully not destroy the formatting again.
Signed-off-by: Bernhard Schmidt <bernhard.schmidt@saxnet.de>
Signed-off-by: Simon Wunderlich <simon.wunderlich@saxnet.de>
Acked-by: Francois Romieu <romieu@zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'XFP' driver is really a driver for the QT2022C2 and QT2025C PHYs,
covering both more and less than XFP. Rename its functions and
constants to reflect reality and to reduce namespace pollution when
sfc is a built-in driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only multi-speed PHY driver using this is 10Xpress, and it does
not support non-autoneg operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_fc_resolve() is specific to MDIO and is not used by any other
function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTD partition is named based on the netdev name, which is set to
'eth%d' before registration. Also, the MTD partition will currently
be left registered if netdev registration fails.
Fix both these problems by moving the MTD probe after netdev
registration. Hold the RTNL to serialise this with the netdev
notifier that calls efx_mtd_rename().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These cleanup functions will never be called if the MMIO region could
not be mapped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC and PHY probing are bound up together, as evidenced by the
initialisation of efx_nic::loopback_modes. Remove the current
arbitrary separation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the implementation a lot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes efx_pci_remove_main() more obviously the inverse of
efx_pci_probe_main(), and matches our out-of-tree driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the duplicated logic in efx_enqueue_skb() and
efx_tx_queue_insert() with an inline function, efx_max_tx_len().
Remove the failed attempt at abstracting hardware-specifics and put
all the magic numbers in efx_max_tx_len().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move size and mask definitions into efx.h; calculate page orders in falcon.c.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're at it, use type suffixes of 'd', 'q' and 'o', consistent
with register type names.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena is still based on the Falcon hardware architecture and will
share many of these definitions, so replace falcon_hwdefs.h with
regs.h.
The new definitions have been generated according to a naming
convention which incorporates the type and revision information.
Update the code accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there are now separate blocks of code to set the thresholds for
each NIC type, it is no longer useful to include them in the NIC type
description.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros are not extensible to more than two NIC types without
repetition of register definitions, and they are only used to deal
with a few fields in RX_CFG_REG and global events which moved between
Falcon rev A1 and B0.
Therefore:
- Move RX_CFG_REG initialisation into its own function which tests the
NIC revision just once
- Explicitly test the NIC revision when checking the RX_RECOVERY flag in
global events
- Merge definitions of RX_XOFF_MAC_EN flag, which did not move
- Remove the macro definitions
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena will require entirely different board code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point (ri_tasklet()), RTNL or dev_base_lock are not held,
we must use dev_get_by_index() instead of __dev_get_by_index()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes the following build failure:
CC drivers/net/au1000_eth.o
/drivers/net/au1000_eth.c: In function 'au1000_set_settings':
/drivers/net/au1000_eth.c:623: error: implicit declaration of function 'capable'
/drivers/net/au1000_eth.c:623: error: 'CAP_NET_ADMIN' undeclared (first use in this function)
/drivers/net/au1000_eth.c:623: error: (Each undeclared identifier is reported only once
/drivers/net/au1000_eth.c:623: error: for each function it appears in.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the reporting of myri10ge port type in ethtool,
and update for new boards.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx
state in order for the PHY write which disables gigabit speed to take
effect. Gigabit speed must be disabled in order for the PHY writes to
registers on page 800 (the wakeup control registers) to work as expected
otherwise the system might not wake via WoL.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 27fbc7d 'mdio: Expose pause frame advertising flags to ethtool'
and c634263 'sfc: 10Xpress: Initialise pause advertising flags'
added to our reported advertising flags.
efx_mdio_set_settings() requires that all advertising flags are
also present in the supported flags, so make sure that is true.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old code assumed board config version in the flash to be 1.
When this will get changed by tools, driver just refuses to
attach. This is unnecessary since driver does not have to
parse board config structure directly (maintained by firmware).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear NX_RESETING bit in netxen_tx_timeout_task() so that
the firmware watchdog task can catch need_reset request
from tx timeout.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid resetting subsys ID in i2c block. Also remove duplicate
check for address tranlsation error.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
move virtrng_remove to .devexit.text
move virtballoon_remove to .devexit.text
virtio_blk: Revert serial number support
virtio: let header files include virtio_ids.h
virtio_blk: revert QUEUE_FLAG_VIRT addition
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
niu: VLAN_ETH_HLEN should be used to make sure that the whole MAC header was copied to the head buffer in the Vlan packets case
KS8851: Fix ks8851_set_rx_mode() for IFF_MULTICAST
KS8851: Fix MAC address write order
KS8851: Add soft reset at probe time
net: fix section mismatch in fec.c
net: Fix struct inet_timewait_sock bitfield annotation
tcp: Try to catch MSG_PEEK bug
net: Fix IP_MULTICAST_IF
bluetooth: static lock key fix
bluetooth: scheduling while atomic bug fix
tcp: fix TCP_DEFER_ACCEPT retrans calculation
tcp: reduce SYN-ACK retrans for TCP_DEFER_ACCEPT
tcp: accept socket after TCP_DEFER_ACCEPT period
Revert "tcp: fix tcp_defer_accept to consider the timeout"
AF_UNIX: Fix deadlock on connecting to shutdown socket
ethoc: clear only pending irqs
ethoc: inline regs access
vmxnet3: use dev_dbg, fix build for CONFIG_BLOCK=n
virtio_net: use dev_kfree_skb_any() in free_old_xmit_skbs()
be2net: fix support for PCI hot plug
...
Rusty,
commit 3ca4f5ca73
virtio: add virtio IDs file
moved all device IDs into a single file. While the change itself is
a very good one, it can break userspace applications. For example
if a userspace tool wanted to get the ID of virtio_net it used to
include virtio_net.h. This does no longer work, since virtio_net.h
does not include virtio_ids.h.
This patch moves all "#include <linux/virtio_ids.h>" from the C
files into the header files, making the header files compatible with
the old ones.
In addition, this patch exports virtio_ids.h to userspace.
CC: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In ks8851_set_rx_mode() the case handling IFF_MULTICAST was also setting
the RXCR1_AE bit by accident. This meant that all unicast frames where
being accepted by the device. Remove RXCR1_AE from this case.
Note, RXCR1_AE was also masking a problem with setting the MAC address
properly, so needs to be applied after fixing the MAC write order.
Fixes a bug reported by Doong, Ping of Micrel. This version of the
patch avoids setting RXCR1_ME for all cases.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC address register was being written in the wrong order, so add
a new address macro to convert mac-address byte to register address and
a ks8851_wrreg8() function to write each byte without having to worry
about any difficult byte swapping.
Fixes a bug reported by Doong, Ping of Micrel.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue a full soft reset at probe time.
This was reported by Doong Ping of Micrel, but no explanation of why this
is necessary or what bug it is fixing. Add it as it does not seem to hurt
the current driver and ensures that the device is in a known state when we
start setting it up.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_init is called by both fec_probe and fec_resume, so it
shouldn't be marked as __init.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the private functions alloc_can_skb() and
alloc_can_err_skb() of the at91_can driver public and adapts all
drivers to use these. While making the patch I realized, that
the skb's are *not* setup consistently. It's now done as shown
below:
skb->protocol = htons(ETH_P_CAN);
skb->pkt_type = PACKET_BROADCAST;
skb->ip_summed = CHECKSUM_UNNECESSARY;
*cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
memset(*cf, 0, sizeof(struct can_frame));
The frame is zeroed out to avoid uninitialized data to be passed to
user space. Some drivers or library code did not set "pkt_type" or
"ip_summed". Also, "__constant_htons()" should not be used for
runtime invocations, as pointed out by David Miller.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2400m-sdio requires iwmc3200top for its operation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwmc3200wifi requires iwmc3200top for its operation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change RX large buffer size based on MTU. If pages are larger
than the MTU the page is divided up into multiple chunks and passed to
the hardware. When pages are smaller than MTU each RX buffer can
contain be comprised of up to 2 pages.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the SDIO part of the TX resources were initialized/released
with bus_dev_{start,stop}.
The generic code's TX subsystem is destroyed afterwards, so there is a
window from the bus-TX destruction to the generic-TX destruction where
the generic-TX code might call into bus-TX to do transactions.
The SDIO code cannot really cope with this (whereas in USB, how it is
laid out, it correctly ignores it). In any case, it made no sense for
the SDIO TX code to be in i2400m->bus_dev_start/stop(), so moved to
i2400m->bus_setup/release(), which also takes care of the oops.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In coming commits, the i2400m SDIO driver will not use
i2400m->bus_dev_stop().
Thus changed to check before calling, as an empty stub has more
overhead than a call to check if the function pointer is non-NULL.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Current i2400m USB code had to threads (one for processing RX, one for
TX). When calling i2400m_{tx,rx}_release(), it would crash if the
thread had exited already due to an error.
So changed the code to have the thread fill in/out
i2400mu->{tx,rx}_kthread under a spinlock; then the _release()
function will call kthread_stop() only if {rx,tx}_kthread is still
set.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Currently __i2400m_dev_start was forcing, after uploading firmware and
doing a few checks to WIMAX_ST_UNINITIALIZED.
This can be overriding state changes that the device might have caused
by sending reports; thus it makes more sense to remove it and let the
device update the status on its own by sending reports.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
All the entry points into the TX module should check if the device has
been torn down. Otherwise, when the device resets or shuts down, there
are windows when a call to i2400m_tx*() will oops the system.
For that, make i2400m_tx_release() set i2400m->tx_buf to NULL under
the tx_lock. Then, any entry point [i2400m_tx(), _tx_msg_sent(),
_tx_msg_get()] will check for i2400m->tx_buf to be NULL and exit
gracefully.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m might start sending reports to the driver before it is done
setting up all the infrastructure needed for handling them.
Currently we were just dropping them when the driver wasn't ready and
that is bad in certain situations, as the sync between the driver's
idea of the device's state and the device's state dissapears.
This changes that by implementing a queue for handling
reports. Incoming reports are appended to it and a workstruct is woken
to process the list of queued reports.
When the device is not yet ready to handle them, the workstruct is not
woken, but at soon as the device becomes ready again, the queue is
processed.
As a consequence of this, i2400m_queue_work() is no longer used, and
thus removed.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Upcoming changes will have to add things to this function that expose
more internals, which would mean more forward declarators.
Frankly, it doesn't need to be an inline, so moved to driver.c, where
the declarations will be taken from the header file.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Since the addition of the pre/post reset handlers, it became clear
that we cannot do a I2400M-RT-BUS type reset while holding the
init_mutex, as in the case of USB, it will deadlock when trying to
call i2400m_pre_reset().
Thus, the following changes:
- clarify the fact that calling bus_reset() w/ I2400M_RT_BUS while
holding init_mutex is a no-no.
- i2400m_dev_reset_handle() will do a BUS reset to recover a gone
device after unlocking init_mutex.
- in the USB reset implementation, when cold and warm reset fails,
fallback to QUEUING a usb reset, not executing a USB reset, so it
happens from another context and does not deadlock.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The stop procedure for the device must make sure that any task that is
waiting on a message is properly cancelled.
This was being taken care of only by the __i2400m_dev_reset_handle()
path and the rest was working by chance because the waits have a
timeout.
Fixed by adding a proper cancellation in __i2400m_dev_stop().
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The actual fw->size may not equal to the bcf size indicated in
the bcf header if the extended bcf debug header is added in the tail.
To reflect the actual fw size that will be downloaded to the device,
it is now retrived from from the size field indicated in the bcf header.
All of the headers (if there are extended headers) should indicate same
value for the size field since only one set of firmware chunks is downloaded
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Both secure and non-secure boot must set the JUMP command in the
bootmode header as the last FW chunk, so we change to use the JUMP
command to decide if the FW chunk download is completed.
Since we tend to use one single FW to support both secure and non-secure
boot for most of the time, I2400M_BRH_SIGNED_JUMP is actually found
even for non-secure boot. But in case the FW does come with
I2400M_BRH_JUMP, we check for both of them in i2400m_dnload_bcf().
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
tcpdump and friends were not being able to decode packets sent via
WiMAX; they had a zero ethernet type, even when the stack was properly
sending them to the device with the right type.
It happens that the driver was overwriting the (fake) ethernet header
for creating the hardware header and that was bitting the cloning used
by tcpdump (et al) to look into the packets.
Use pkskb_expand_head() [method copied from the e1000 driver] to fix.
Thanks to Herbert Xu and Andi Kleen for helping to diagnose and
pointing to the right fix.
Cc: Herbert Xu <gondor.apana.org.au>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Missed a debug message that was being constantly printed as a
dev_err(); became annoying. Demote it to a debug message.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The USB stack can callback a driver is about to be reset by an
external entity and right after it, so the driver can save state and
then restore it.
This commit implements said support; it is implemented actually in the
core, bus-generic driver [i2400m_{pre,post}_reset()] and used by the
bus-specific drivers. This way the SDIO driver can also use it once
said support is brought to the SDIO stack.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
After the introduction of i2400m->bus_setup/release, there is no more
race condition where the bootmode buffers are needed before
i2400m_setup() is called.
Before, the SDIO driver would setup RX before calling i2400m_setup()
and thus need those buffers; now RX setup is done in
i2400m->bus_setup(), which is called by i2400m_setup().
Thus, all the bootmode buffer management can now be done completely
inside i2400m_setup()/i2400m_release(), removing complexity from the
bus-specific drivers.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The SDIO subdriver of the i2400m requires certain steps to be done
before we do any acces to the device, even for doing firmware upload.
This lead to a few ugly hacks, which basically involve doing those
steps in probe() before calling i2400m_setup() and undoing them in
disconnect() after claling i2400m_release(); but then, much of those
steps have to be repeated when resetting the device, suspending, etc
(in upcoming pre/post reset support).
Thus, a new pair of optional, bus-specific calls
i2400m->bus_{setup/release} are introduced. These are used to setup
basic infrastructure needed to load firmware onto the device.
This commit also updates the SDIO subdriver to use said calls.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m driver uses two different bits to distinguish how much the
driver is up. i2400m->ready is used to denote that the infrastructure
to communicate with the device is up and running. i2400m->updown is
used to indicate if 'ready' and the device is up and running, ready to
take control and data traffic.
However, all this was pretty dirty and not clear, with many open spots
where race conditions were present.
This commit cleans up the situation by:
- documenting the usage of both bits
- setting them only in specific, well controlled places
(i2400m_dev_start, i2400m_dev_stop)
- ensuring the i2400m workqueue can't get in the middle of the
setting by flushing it when i2400m->ready is set to zero. This
allows the report hook not having to check again for the bit to be
set [rx.c:i2400m_report_hook_work()].
- using i2400m->updown to determine if the device is up and running
instead of the wimax state in i2400m_dev_reset_handle().
- not loosing missed messages sent by the hardware before
i2400m->ready is set. In rx.c, whatever the device sends can be
sent to user space over the message pipes as soon as the wimax
device is registered, so don't wait for i2400m->ready to be set.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Currently the i2400m driver was starting in a weird way: registering a
network device, setting the device up and then registering a WiMAX
device.
This is an historic artifact, and was causing issues, a some early
reports the device sends were getting lost by issue of the wimax_dev
not being registered.
Fix said situation by doing the wimax device registration in
i2400m_setup() after network device registration and before starting
thed device.
As well, removed spurious setting of the state to UNINITIALIZED;
i2400m.dev_start() does that already.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When the i2400m device needs to wake up an idle WiMAX connection, it
schedules a workqueue job to do it.
Currently, only when the network stack called the _stop() method this
work struct was being cancelled. This has to be done every time the
device is stopped.
So add a call in i2400m_dev_stop() to take care of such cleanup, which
is now wrapped in i2400m_net_wake_stop().
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Make sure that i2400m_dev_bootstrap() doesn't overwrite the last known
error code with -ENOENT; when a firmware fails to load, we want to
know the cause and not a generic error code.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Current driver didn't implement the .reset_resume method. The i2400m
normally always reset on a comeback from system standby/hibernation.
This requires previously applied commits to cache the firmware image
file.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In preparation for a reset_resume implementation, have the firmware
image be cached in memory when the system goes to suspend and released
when out.
This is needed in case the device resets during suspend; the driver
can't load firmware until resume is completed or bad deadlocks
happen.
The modus operandi for this was copied from the Orinoco USB driver.
The caching is done with a kobject to avoid race conditions when
releasing it. The fw loader path is altered only to first check for a
cached image before trying to load from disk. A Power Management event
notifier is register to call i2400m_fw_cache() or i2400m_fw_uncache()
which take care of the actual cache management.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In preparation for reset_resume support, in which the same code path
is going to be used, add a diagnostic message to dev_reset_handle()
that can be used to distinguish how the device got there.
This uses the new payload argument added to i2400m_schedule_work() by
the previous commit.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Forthcoming commits use having a payload argument added to
i2400m_schedule_work(), which then becomes nearly identical to
i2400m_queue_work().
This patch thus cleans up both's implementation, making it share
common helpers and adding the payload argument to
i2400m_schedule_work().
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Add support for the WiMAX device in the Intel WiFi/WiMAX Link 6050
Series; this involves:
- adding the device ID to bind to and an endpoint mapping for the
driver to use.
- at probe() time, some things are set depending on the device id:
+ the list of firmware names to try
+ mapping of endpoints
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Different sdio device IDs are designated to support different intel
wimax silicon sku. The new macro SDIO_DEVICE_ID_IWMC3200_WIMAX_2G5(0x1407)
is added to support iwmc3200 2.5GHz sku. The existing
SDIO_DEVICE_ID_IWMC3200_WIMAX(0x1402) is for iwmc3200 general sku.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Devices based on the i2400m emit a "barker" (32 bit unsigned) when
they boot. This barker is used to select, in the firmware file image,
which header should be used to process the rest of the file.
This commit implements said support, completing the series started by
previous commits.
We modify the i2400m_fw_dnload() firmware loading path by adding a
call to i2400m_bcf_hdr_find() [new function], in which the right BCF
header [as listed in i2400m->fw_hdrs by i2400m_fw_check()] is
located. Then this header is fed to i2400m_dnload_init() and
i2400m_dnload_finalize().
The changes to i2400m_dnload_finalize() are smaller than they look;
they add the bcf_hdr argument and use that instead of bcf. Likewise in
i2400m_dnload_init().
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The SBCF firmware format has been extended to support extra headers
after the main payload. These extra headers are used to sign the
firmware code with more than one certificate. This eases up
distributing single code images that work in more than one SKU of the
device.
The changes to support this feature will be spread in a series of
commits. This one just adds the support to parse the extra headers and
store them in i2400m->fw_hdrs. Coming changes to the loader code will
use that to determine which header to upload to the device.
The i2400m_fw_check() function now iterates over all the headers and
for each, calls i2400m_fw_hdr_check(), which does some basic checks on
each header. It then stores the headers for the bootloader code to use.
The i2400m_dev_bootstrap() function has been modified to cleanup
i2400m->fw_hdrs when done.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Make sure the bootloading code checks that the format of the file is
understood (major version match). This also fixes a dumb typo in
extracting the major version field.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m based devices can get in a sort of a deadlock some times;
when they boot, they send a reboot "barker" (a magic number) and then
the driver has to echo that same barker to ack reception
(echo/ack). Then the device does a final ack by sending an ACK barker.
The first time this happens, we don't know ahead of time with barker
the device is going to send, as different device models and SKUs will
send different barker depending on the EEPROM programming.
If the device has sent the barker before the driver has been able to
read it, the driver looses, as it doesn't know which barker it has to
echo/ack back. With older devices, we tried a couple of combinations
and that always worked; but now, with adding support for more, in
which we have an unlimited number of new barkers, that is not an
option.
So we rework said case so that when the device gets stuck, we just
cycle through all the known types until one forces the device to send
an ack. Otherwise, the driver gives up and aborts.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m firmware loader is given a list of firmware files to try to
load by the probe() function (which can be different based on the
device's model / generation).
Current code didn't attempt to load, check and try to boot with each
file, but just to try to load if off disk. This is limiting in some
cases, where we might want to try to load a firmware and if it fails
to load onto the device, just fall back to another one.
This changes the behaviour so all files are tried for being loaded
from disk, checked and uploaded to the device until one suceeds in
bringing the device up.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
This modifies the bootrom initialization code of the i2400m driver so
it can more easily support upcoming hardware.
Currently, the code detects two types of barkers (magic numbers) sent
by the device to indicate the types of firmware it would take (signed
vs non-signed).
This schema is extended so that multiple reboot barkers are
recognized; upcoming hw will expose more types barkers which will have
to match a header in the firmware image before we can load it.
For that, a barker database is introduced; the first time the device
sends a barker, it is matched in the database. That gives the driver
the information needed to decide how to upload the firmware and which
types of firmware to use. The database can be populated from module
parameters.
The execution flow is not altered; a new function
(i2400m_is_boot_barker) is introduced to determine in the RX path if
the device has sent a boot barker. This function is becoming heavier,
so it is put away from the hot reception path [this is why there is
some reorganization in sdio-rx.c:i2400ms_rx and
usb-notifc.c:i2400mu_notification_grok()].
The documentation on the process has also been updated.
All these modifications are heavily based on previous work by Dirk
Brandewie <dirk.brandewie@intel.com>.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m based devices can boot two main types of firmware images:
signed and non-signed. Signed images have signature data included that
must match that of a certificate stored in the device.
Currently the code is making the decission on what type of firmware
load (signed vs non-signed) is going to be loaded based on a hardcoded
decission in __i2400m_ack_verify(), based on the barker the device
sent upon boot.
This is not flexible enough as future hardware will emit more barkers;
thus the bit has to be set in a place where there is better knowledge
of what is going on. This will be done in follow-up commits -- however
this patch paves the way for it.
So the querying of the mode is packed into i2400m_boot_is_signed();
the main changes are just using i2400m_boot_is_signed() to determine
the method to follow and setting i2400m->sboot in
i2400m_is_boot_barker(). The modifications in i2400m_dnload_init() and
i2400m_dnload_finalize() are just reorganizing the order of the if
blocks and thus look larger than they really are.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Add "debug" module options to all the wimax modules (including
drivers) so that the debug levels can be set upon kernel boot or
module load time.
This is needed as currently there was a limitation where the debug
levels could only be set when a device was succesfully
enumerated. This made it difficult to debug issues that made a device
not probe properly.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m driver was missing the definition for the sysfs debug
level, which is declared in debug-levels.h.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In the Intel Wireless Multicomm 3200, the initialization is
orchestrated by a component called Top. This component also monitors
how many times a function is reset (via sdio_disable) to detect
possible issues and will reset the whole multifunction device if any
function triggers a maximum reset level.
During WiMAX's probe, the driver needs to wait for Top to come up
before it can enable the WiMAX function. If it cannot, it will return
-ENODEV and the Top driver will rescan the SDIO bus once done
loading.
Currently, the WiMAX SDIO probe routine was trying a few times before
returning -ENODEV, and this was triggering Top's too-many-resets
detector. This is, in any case, unnecessary because the Top driver will
force the bus rescan when the functions can be probed successfully.
Added then a maxtries argument to i2400ms_enable_func() and set it to
1 when calling from probe. We want to reuse this function instead of
flat calling out sdio_enable_func() to take advantage of hardware
quirk workarounds.
Reported-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In kernel 2.6.31, the firmware requested to ram could be marked
with read only attribute, and we can't write any thing directly
to the memory when setting up the last JUMP brh cmd.
Changed so that the scratch buffer is used.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Because some underlying bus APIs (like USB) don't like data buffers in
the stack or vmalloced areas, the i2400m driver provides a scratch
buffer (i2400m->bm_cmd_buf) for said low-level drivers to copy command
data to before passing it to said API. This is only used during boot
mode.
However, at some the code was copying the buffer even when the command
was already specified in said buffer. This is ok, but it needs to be
more careful. As thus, change so that:
(a) the copy happens only if command buffer is not the scratch buffer
(b) use memmove() in case there is overlapping
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In order to avoid issues during high-load traffic, the interrupt
status register has to be cleared ONLY after the RX size is read.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Newer generations of the i2400m USB WiMAX device use a different
endpoint map; in order to make it easy to support it, we make the
endpoint-to-function mapeable instead of static.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When trying to enable the iwmc3200 WiMAX SDIO function, we loop
waiting for the top controller to be up and running (at which point we
can succesfully enable the function). Between each try we wait for
I2400MS_INIT_SLEEP_INTERVAL ms.
Integration tests have found the current value of 10ms to be too
short; it was upped to 100ms to give more time to the top controller
to be ready.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In the iwmc3200, disabling the WiMAX SDIO function when enable fails
would possibly result in a device reset triggered by the iwmc3200's
top controller since it monitors the bus reset activities from each
SDIO function. In any case, the disable makes no sense; if the enable
fails, it should not be disabled.
Thus we remove the unecessary sdio_disable_func() in
i2400ms_enable_function().
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The default SDIO IOE wait timeout returned from iwmc3200-wimax's CCCR
is not efficient. This inefficiency will actually cause problems on
Moorestown platforms (system hang).
This is a sillicon bug that requires a software patch to by
overwritting func->enable_timeout. The new value I2400MS_IOR_TIMEOUT
is recommended and verified from the system integration results.
Future sillicon releases will have this default value corrected in the
future.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In i2400m-based devices, the driver's bootloader will retry to load
the firmware when things go wrong. The driver currently has a constant
(I2400M_BOOT_RETRIES) which governs the max number of tries.
However, different SKUs of the same hardware may admit or require
different numbers of retries due to it's particulars, so it is made a
BUS specific parameter and different values are assigned for 5x50
devices versus the 3200 ones.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The change to the SDIO boot mode RX chain could try to use the cmd and
ack buffers befor they were allocated. USB does not have the problem
but both were changed for consistency's sake.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Add minimal ethtool support for carrier detection.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Ensure that index `status' remains within ms_to_errno[]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
i2400ms_bus_bm_wait_for_ack() causes a race condition. It happens
because this function clears i2400ms->bm_ack_size before waiting for
an interrupt, which is set by the interrupt service routine i2400ms_rx()
to indicate reception and size of received data; thus, if the interrupt
came right before the clearing/waiting, it is lost.
The fix is clear the bm_ack_size to -EINPROGRESS before we are enabling
the RX interrupt configuration in i2400ms_rx_setup(). Then everytime
when the interrupt service routine i2400ms_rx() is invoked during bootmode,
bm_ack_size is updated with the actual rx_size and it is cleared to
-EINPROGRESS again after the RX data is handled.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
This patch removes an unneeded power management primitive.
Power management is automatically enabled as probe ends.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
This patch fixed the problem of dropped packets due to lost of
interrupt requests. We should only clear what was pending at the
moment we read the irq source reg.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have better cache layouts of struct sock (separate zones
for rx/tx paths), we need this preliminary patch.
Goal is to transfert fields used at lookup time in the first
read-mostly cache line (inside struct sock_common) and move sk_refcnt
to a separate cache line (only written by rx path)
This patch adds inet_ prefix to daddr, rcv_saddr, dport, num, saddr,
sport and id fields. This allows a future patch to define these
fields as macros, like sk_refcnt, without name clashes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xmit handler doesn't need to wake the queue after stopping
it temporarily (some other drivers are doing the same).
Patch on net-next-2.6, multiple netperf sessions tested.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware hang detection and recovery (reset) need to
be disabled for diagnostic tools, which can run
some disruptive tests.
This adds a driver level control to turn off this
feature by diag tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use -EIO or -EINVAL as error codes, these can get passed up
to applications (tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for different windowing scheme for on chip
memory in future chip revisions. This is required by
diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future revisions need different chip reset sequence
and firmware initialization.
Also clean up some never used debug code.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future revisions of the chip have 128 bit memory
transactions. Require drivers to implement rmw
in case of sub-128 bit accesses by driver. This
is mostly used by diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new PCI ids to support next generation of BladeEngine device.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 was using dprintk() for debugging output. This was
defined in <linux/dst.h> and was the only thing that was
used from that header file. This caused compile errors
when CONFIG_BLOCK was not enabled due to bio* and BIO*
uses in the header file, so change this driver to use
dev_dbg() for debugging output.
include/linux/dst.h:520: error: dereferencing pointer to incomplete type
include/linux/dst.h:520: error: 'BIO_POOL_BITS' undeclared (first use in this function)
include/linux/dst.h:521: error: dereferencing pointer to incomplete type
include/linux/dst.h:522: error: dereferencing pointer to incomplete type
include/linux/dst.h:525: error: dereferencing pointer to incomplete type
make[4]: *** [drivers/net/vmxnet3/vmxnet3_drv.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is limited to the maximal BW allocation, so it should be displayed as
the link speed to notify the user.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is really no need to clear the MAC or the FW filtering rules - it was
added for completion, but caused race conditions with load/unload. Removing this
redundant code
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCC commands are not protected with the RTNL lock, so a mutex should be added
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working with DCC, a function can be disabled or enabled (virtual link down
or up). Using the function state introduced some race conditions with the
load/unload flow.
Using a separate flag to indicate that the function is disabled.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of zero was used to disable the fairness mechanism. Though the code
(driver and FW) allowed changing the value at run time, it did not allow to do
that if the mechanism was disabled to begin with.
Fixed the FW to allow turning on and off the mechanism at run time. Fixed the
code to read the value from the chip at the right sequence.
Without this fix, if the initial value was set to zero, traffic could not run on
the interface.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before issuing any cmds to the FW, the driver must first wait
till the fW becomes ready. This is needed for PCI hot plug when
the driver can be probed while the card fw is being initialized.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 uses in_dev* interfaces so it should depend on INET.
Also fix so that the driver builds when CONFIG_PCI_MSI is disabled.
vmxnet3_drv.c:(.text+0x2a88cb): undefined reference to `in_dev_finish_destroy'
drivers/net/vmxnet3/vmxnet3_drv.c:1335: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:1384: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2137: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2138: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bhavesh davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Randy Dunlap <randy.dunlap@oracle.com>
ks8851_mll uses mii interfaces so it needs to select MII.
ks8851_mll.c:(.text+0xf95ac): undefined reference to `generic_mii_ioctl'
ks8851_mll.c:(.text+0xf96a0): undefined reference to `mii_ethtool_gset'
ks8851_mll.c:(.text+0xf96fa): undefined reference to `mii_ethtool_sset'
ks8851_mll.c:(.text+0xf9754): undefined reference to `mii_link_ok'
ks8851_mll.c:(.text+0xf97ae): undefined reference to `mii_nway_restart'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus cannot be accessed at interrupt context, but on an FEC
error, the fec_mpc52xx driver reset function also tries to reset the
PHY. Since the error is detected at IRQ context, and the PHY functions
try to sleep, the kernel ends up panicking.
Resetting the PHY on an FEC error isn't even necessary. This patch
solves the problem by removing the PHY reset entirely.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some OF platform drivers are missing module device tables, so they won't
load automatically on boot. This patch fixes the issue by adding proper
MODULE_DEVICE_TABLE() macros to the drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MT26438 (ConnectX EN 40GigE PCIe 2.0 5GT/s) to the list of supported
devices.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The lock_kernel/unlock_kernel() in cycle_kernel_lock() which is called
in tun_chr_open() is not serializing against anything and safe to
remove.
tun_chr_fasync() is serialized by get/put_tun() and fasync_helper()
has no dependency on BKL. The modification of tun->flags is racy with
and without the BKL so removing it does not make it worse.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mechanism to clear the statistics register is dependent
on the status of GMIIEN bit in MAC control register. If the
GMIIEN bit is set, the stats registers are write to decrement.
If the GMIIEN bit is cleared, the stats registers are plain
read/write registers. The stats register clearing operation
must take into account the current state of GMIIEN as it
can be cleared when the interface is brought down.
With existing implementation logic, querying for interface stats
when the interface is down, can corrupt the statistics counters.
This patch examines the GMIIEN bit status in MAC_CONTROL
register before choosing an appropriate mask for clearing stats
registers.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extracted from Realtek's 8.012.00 r8168 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the driver to accept a MAC address specified in platform_data.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5675f221 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 337e067d overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 23d26497 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fd8235bb overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 59aa3cc4 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sysfs entries to enable register and memory access
for diagnostic tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since register and onboard memory access has separate
window registers, they need not be kept under same lock.
Also, memory is always accessed from process context
(mostly for firmware init and diagnostic tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use common variables crb_win, ocm_win for all revisions of chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access to on chip memory, this is used by
debug and diagnostic tools only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sub 64-bit / unaligned access to oncard memory was only used
by old diagnostic tools, causes some intermittent issues when
memory controller agent is used. The new access method was
added by commit ea6828b8aa
("netxen: improve pci memory access"). Firmware init anyway
uses 8-byte strides.
This also fixes address/offset calculation for NX2031 context
memory (SIU). For NX3031, SIU uses same register offsets
as packet memory (MIU).
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d43c36dc6b ("headers: remove
sched.h from interrupt.h") left some build errors in some configurations
due to drivers having depended on getting header files "accidentally".
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Combined several one-liners from Ingo into one single patch - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bit V_MAC_RX_PL_THRSH(4) was already set a few lines higher.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The negation makes it a bool before the comparison and hence it
will never evaluate to true.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added support of private MAC address per port and provisioning
packet handler for iSCSI traffic only.
The above changes are isolated to the cxgb3 driver, independent of any scsi or iscsi driver changes.
Acked-by: Karen Xie <kxie@chelsio.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Rakesh Ranjan <rakesh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Runtime PM support to the sh_eth driver.
The clock to the ethernet hardware block will be
enabled as long as the network device is up.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the sh_eth driver to allow passing the mac address
using the platform data structure. This to simplify board
setup code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the CAN controller driver to define the number of echo
skb's used for the local loopback (echo), as suggested by Kurt Van
Dijck, with the function:
struct net_device *alloc_candev(int sizeof_priv,
unsigned int echo_skb_max);
The CAN drivers have been adapted accordingly. For the ems_usb driver,
as suggested by Sebastian Haas, the number of echo skb's has been
increased to 10, which improves the transmission performance a lot.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cisco HDLC uses keepalive packets and sequence numbers to determine link
state. In rare cases both ends could transmit keepalive packets at the same
time, causing the received sequence numbers to be treated as incorrect.
Now we accept our current sequence number as well as the previous one.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function bond_create_proc_entry is currently of type int.
Two versions of this function exist:
The one in the ifdef CONFIG_PROC_FS branch always return 0.
The one in the else branch (which is empty) return nothing.
When CONFIG_PROC_FS is undef, this cause the following warning:
drivers/net/bonding/bond_main.c: In function `bond_create_proc_entry':
drivers/net/bonding/bond_main.c:3393: warning: control reaches end of
non-void function
No caller of this function use the returned value.
So change the returned type from int to void and remove the
useless return 0; .
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Reported-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c574_cs:
spin_lock the set_multicast_list function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Belkin F8T012xx1 bluetooth adaptor has the same vendor and product
IDs as the Belkin F5D5050, so we need to teach the pegasus driver to
ignore adaptors belonging to the "Wireless" class 0xE0. For this one
case anyway, seeing as pegasus is a driver for "Wired" adaptors.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size_t for PCI resource remapping instead
of unsigned long. Physical addresses can exceed range of
long data type (e.g with PAE).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethoc.c: In function ‘ethoc_open’:
drivers/net/ethoc.c:667: warning: comparison of distinct pointer types
lacks a cast
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet NIC driver for VMware's vmxnet3
From: Shreyas Bhatewara <sbhatewara@vmware.com>
This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3
Guests running on VMware hypervisors supporting vmxnet3 device will thus have
access to improved network functionalities and performance.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Ronghua Zhang <ronghua@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IXP 2000 network driver was failing to build as it has its own
statistics gathering which was not compatible with the recent network
device operations changes. This patch fixes the driver in the obvious
way and has been compile tested. I have been unable to get the ixp2000
maintainer to comment or test this fix.
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio module now handles reconfiguration of pause advertising
through ethtool, but not initialisation. Add the necessary
initialisation to tenxpress_phy_init().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mdio45_ethtool_gset_npage() and mdio45_ethtool_gset(), check MDIO
pause frame advertising flags and set the corresponding ethtool flags.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if pause autoneg is off we do not set either pause
advertising flag. If autonegotiation of speed and duplex settings is
enabled, there is no way for the link partner to distinguish this from
our refusing to use pause frames.
We should instead set the advertising flags according to the forced
mode so that the link partner can follow our lead. This is consistent
with the behaviour of other drivers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to various cleanups and refactorings this is now straightforward:
convert the gianfar driver to dev_pm_ops, plus add ->restore() callback
that will fully reinitialize MAC internal registers and BDs.
Note that I kept legacy suspend/resume callbacks so that this patch
doesn't depend on PowerPC changes (i.e. dev_pm_ops support for OF
platform drivers).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After hibernation we want to just reinitialize BDs, no need to allocate
anything. So, factor out BDs initialization code from
gfar_alloc_skb_resourses().
Also, teach gfar_init_bds() to reuse already allocated RX SKBs, i.e.
just call gfar_init_rxbdp() if a SKB was already allocated and mapped.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to just reinitialize RX BDs after hibernation, no need to
map the skb->data again. So let's factor gfar_init_rxbdp() out of
gfar_new_rxbdp().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hibernation we want to call gfar_init_mac() without need to
free/allocate_skb_resources sequence, so save the DMA address into a
private struct, and move tbase/rbase initialization to gfar_init_mac().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new functions implemented: gfar_alloc_skb_resources() and
gfar_init_mac(). We'll use gfar_init_mac() for restoring after
hibernation.
The patch just moves the code around, there should be no functional
changes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
startup_gfar() sets the wrap bit for the last rxbd just after
gfar_new_rxbdp() call, which is issued for all rxbds. And
gfar_new_rxbdp() has the following check already:
if (bdp == priv->rx_bd_base + priv->rx_ring_size - 1)
lstatus |= BD_LFLAG(RXBD_WRAP);
So we don't need to set the bit again.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dma_free_coherent() from stop_gfar() and gfar_start() calls,
place it into free_skb_resources(). That makes SKB resources management
more understandable, plus free_skb_resources() will be used as a cleanup
routine for gfar_alloc_skb_resources() that will be implemented soon.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're going to split the startup_gfar() into 3 separate functions,
so let's cleanup the code a little bit so that cosmetic changes
won't distract attention from logical ones.
- Remove needless casts (e.g. (struct sk_buff **)kmalloc());
- Turn 'unsigned long vaddr;' into 'void *vaddr', to avoid casting;
- Add new 'struct device *dev' variable as a shorthand for
'&priv->ofdev->dev' that is used all over the place, also rename
'struct net_device *dev' to 'struct net_device *ndev';
- Turn printk(KERN_ERR ...) to pr_err(...), which is shorter;
- Don't return bogus -1 (i.e. -EPERM) when request_irq() fails;
- Turn '&priv->regs->' to just '®s->'.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/cnic.c: In function 'cnic_init_storm_conn_bufs':
drivers/net/cnic.c:1757: error: implicit declaration of function 'csum_ipv6_magic'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool set settings to pasemi_mac_ethtool.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to the way it interacts with the networking
stack and other parts of mac80211, ieee80211_rx()
must be called with disabled softirqs.
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/39440/focus=40266
Reported-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to free the dynamic allocated memory before ieee80211_free_hw();
once call ieee80211_free_hw(), should not reference to "priv" data
structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If ace_load_firmware() fails, ace_init() cleans up but still returns
0, leading to an oops as seen in <http://bugs.debian.org/521383>.
It should pass the error code up.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add iSCSI support for bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hardware and software structures for bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor ring init. code for subsequent 10G patches. Also add rtnl_lock()
in cnic_uio_open() to prevent race condition with netdev events.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the main CNIC registration, callback, MAC addr. setup functions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to initialize hardware blocks used for iSCSI.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For iSCSI MAC address setup in later patches.
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the SPQ (slow-path queue) operations will be used
by the cnic code in later patches.
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_ring->sbq_buf_len now holds the length of the mapped portion of the
buffer rather than the overall length.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has nothing to do, but this marker prevents the event from
showing up 'not handled'.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove explicit setting of error reporting bits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
We need PHY drivers to initialize in a static kernel before
the MAC drivers that use them. So link them in first.
Based upon a report by Felix Radensky.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is somewhat non-sensical to allow selecting wireless
drivers without showing wireless core code options, and
since the wext refactoring this has made it possible to
generate configurations that will not build. Avoid this
and make wireless drivers select the wireless options.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This came in through the patch titled:
libertas: first stab at cfg80211 support
I only noticed it because it breaks compat-wireless :)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: sujith.manoharan@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the recently added backplane device IDs that support KR
to fail over to KX during link setup. This is accomplished by the new MAC
link setup function ixgbe_setup_mac_link_smartspeed(). Comments were also
updated to better document the reason for the delays chosen for KX, KX4, BX,
BX4 and KR connections.
Signed-off-by: Don Skidmore <don.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add the device ID for the 82599-based Ethernet
Express Module X520-P2 SFI card.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the EMAC V4 implementations support 16K Tx FIFOs. This
patch adds support for this functionality and fixes typos in the
Tx FIFO size error messages.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Victor Gallardo <vgallardo@appliedmicro.com>
Acked-by: Loc Ho <lho@appliedmicro.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was accidentally omitted from one of the previous patches for firmware event
handling. The handler needs to the enable firmware irq mask when it's done
processing or it may not get any more events interrupts.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call set_multi API after reset recovery. This was exposed by tripping
tx_timeout.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wait for NIC fifo and MGMNT fifo to empty before applying reset.
Otherwise broken frames can be processed by management processor and
cause it to hang.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addresses were being added to the filter properly, but were not
being enabled. This adds enable bit to filter write.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcast/multicast should always be routed to the default (zeroeth) rx
ring. Broadcast frames are already routed correctly. This fixes
routing for multicast frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently frames are routed based on their type and MAC address. This
patch adds the port number on which the frame arrived to the routing.
This prevents problems in the case where both interfaces have the same MAC address in
a routing configuration.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix RX queue table size and change from random to default hash values.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
ethoc: limit the number of buffers to 128
ethoc: use system memory as buffer
ethoc: align received packet to make IP header at word boundary
ethoc: fix buffer address mapping
ethoc: fix typo to compute number of tx descriptors
au1000_eth: Duplicate test of RX_OVERLEN bit in update_rx_stats()
netxen: Fix Unlikely(x) > y
pasemi_mac: ethtool get settings fix
add maintainer for network drop monitor kernel service
tg3: Fix phylib locking strategy
rndis_host: support ETHTOOL_GPERMADDR
ipv4: arp_notify address list bug
gigaset: add kerneldoc comments
gigaset: correct debugging output selection
gigaset: improve error recovery
gigaset: fix device ERROR response handling
gigaset: announce if built with debugging
gigaset: handle isoc frame errors more gracefully
gigaset: linearize skb
gigaset: fix reject/hangup handling
...
TI HECC (High End CAN Controller) module is found on many TI devices. It
has 32 hardware mailboxes with full implementation of CAN protocol 2.0B
with bus speeds up to 1Mbps. Specifications of the module are available
on TI web <http://www.ti.com>
Signed-off-by: Anant Gole <anantgole@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private myri10ge_priv structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable old_active is first set to bond->curr_active_slave.
Then, it is unconditionally set to new_active, without being used in between.
The first assignment, having no side effect, is useless.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing module parameters, bond_check_params() erroneously use
'xor_mode' as the name of a module parameter in an error message.
The right name for this parameter is 'xmit_hash_policy'.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
As kindly pointed out by Andrey Yurovsky, CONFIG_LIBERTAS already
selects FW_LOADER.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lbs_is_cmd_allowed() check is added in __lbs_cmd_async() and
lbs_prepare_and_send_command(). The check is removed from other places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And move it to hw code on mac.c where it belongs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The core driver needs to be stopped and then as a last step the
hardware needs to be stopped and its structure free'd. We do this
by moving the core driver cleanup to a new helper ath_clean_core()
and have ath_cleanup() call it. Only as a last step does
ath_cleanup() now free the hw.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used in several places, ensure we do it right in all
callers by using a helper.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs uses the hardware for several debugfs files as such the
hardware must be initialized and available prior to its usage. The
same applies to when we free the hw structs -- free debufs file
entries prior to free'ing the hardware.
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
What this means is we can enable now debug prints without
requiring CONFIG_ATH9K_DEBUG.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has long provided us the association ID. This isn't useful except
for Power-Save polling which now gets enabled. We can now poll for our
pending frames on the AP during power save.
You can review the details of Power-Save on the wireless wiki:
http://wireless.kernel.org/en/developers/Documentation/ieee80211/power-savings
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a regression introduced by patch titled:
"atheros: define shared bssidmask setting"
The register for the BSSID was exchanged for the bssid mask register.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have access to common->curbssid and common->curaid so just
use those. Note that common->curaid is always 0 so this keeps
our current behaviour of always using 0 for now. Once we fix
storing the association ID passed by mac80211 this will
require no changes here.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The trick was to add four bytes whenever this was used. There
are two places where this was missed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo on the second bssid mask register.
This was caused by the patch titled:
"ath5k: use common curbssid, bssidmask and macaddr"
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also sorts all "source" lines in the wireless/Kconfig.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the suspend and resume callbacks of ath5k by converting the
driver to struct dev_pm_ops and allowing the PCI PM core to do the
PCI-specific suspend/resume handling.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set firmware and hardware version in wiphy so that user space can access
it.
(Modification from original in favor of cfg80211 ethtool support. -- JWL)
Cc: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both 1000 & 6000 series NICs contain on-chip OTP memory that
replaces the off-chip EEPROM memory. The nature of OTP means
there is a limited number of times a particular board can go through the
factory flow and be (re)calibrated. As a consequence there will be some boards
that contain EEPROM memory because OTP blocks were full.
In the signature validation routine, iwlwifi needs to make sure
"select bit" and "EEPROM/OTP signature" agree on the type of
NVM to be used to configure the system.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace iwl_poll_direct_bit with iwl_poll_bit when accessing CSR registers.
There is no need to power up the mac to access CSR registers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unify the usage of apm_stop_master and apm_stop
across all hardwares.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwlwifi drivers have LED blinking requirements that
mac80211 cannot fulfill due to the use of just a single
LED instead of different ones for TX, RX, radio etc.
Instead, the single LED blinks according to transfers
and is solid on the rest of the time. As such, having
LED class devices registered that mac80211 triggers are
connected to is pointless as we don't use the triggers
anyway.
Remove all the useless code and add hooks into the
driver itself. At the same time, make the LED code
abstracted so the core code that determines blink rate
etc. can be shared between 3945 and agn in iwlcore.
At the same time, the fact that we removed the use of
the mac80211 LED triggers means we can also remove the
IWLWIFI_LEDS Kconfig symbol since the LED support is
now self-contained.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to have an easier way to debug issues, create
trace events (using the ftrace framework) that will
allow us to follow exactly what the driver is doing
with the device.
The text format isn't all that useful, but the binary
format can also be obtained easily via debugfs and
then analysed on the fly or offline with debugging
tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple MPDUs can be aggregated, transmitted, and finally acknowledged
together using a single BA frame. Block ACK (BA) contains
bitmap size of 64*16 bits so the maximum frame count is 64.
The default value of aggregation frame count suggested by uCode is 31 to
achieve best performance.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver should clear the translate table area after receiving "Alive"
response from uCode. This patch corrects a mistake when doing this.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Guo Chaohong <chaohong.guo@linux.intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to support different type of 1000 series NICs we release to
customers before the production release, iwlwifi driver need to support
all the NICs has EEPROM version greater than 0x15c.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When uCode detects critical temperature it should send "card state
notification" interrupt to driver and then shut itself down to prevent
overheating. There is a race condition where uCode shuts down before it
can deliver the interrupt to driver.
Additional method provided here for driver to enter CT_KILL state based
on temperature reading.
How it works:
Method 1:
If driver receive "card state notification" interrupt from uCode; it
enters "CT_KILL" state immediately
Method 2:
If the last temperature report by Card reach Critical temperature,
driver will send "statistic notification" request to uCode to verify the
temperature reading, if driver can not get reply from uCode within
300ms, driver will enter CT_KILL state automatically.
Method 3:
If the last temperature report by Card did not reach Critical
temperature, but uCode already shut down due to critical temperature.
All the host commands send to uCode will not get process by uCode;
when command queue reach the limit, driver will check the last reported
temperature reading, if it is within pre-defined margin, enter "CT_KILL"
state immediately. In this case, when uCode ready to exit from "CT_KILL" state,
driver need to restart the adapter in order to reset all the queues and
resume normal operation.
One additional issue being address here, when system is in CT_KILL
state, both tx and rx already stopped, but driver still can send host
command to uCode, it will flood the command queue since card was not
responding; adding STATUS_CT_KILL flag to reject enqueue host commands
to uCode if it is in CT_KILL state, when uCode is ready to come out of
CT_KILL, driver will clear the STATUS_CT_KILL bit and allow enqueue the host
commands to uCode to recover from CT_KILL state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The file was accidentally added in commit ef2f8d4577 ("wl1251: add
wl1251 prefix to all 1251 files"). This happened when I rebased the
patches from a private tree.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add timer based auto deep sleep feature in libertas driver which can be
configured using iwconfig command. This is tested on SD8688, SD8686 cards
with firmware versions 10.38.1.p25, 9.70.4.p0 respectively on 32-bit and 64-bit
platforms. Tests have been done for USB/CS cards to make sure that the patch
won't break USB/CS code. We didn't test the if_spi driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor wext to
* split out iwpriv handling
* split out iwspy handling
* split out procfs support
* allow cfg80211 to have wireless extensions compat code
w/o CONFIG_WIRELESS_EXT
After this, drivers need to
- select WIRELESS_EXT - for wext support
- select WEXT_PRIV - for iwpriv support
- select WEXT_SPY - for iwspy support
except cfg80211 -- which gets new hooks in wext-core.c
and can then get wext handlers without CONFIG_WIRELESS_EXT.
Wireless extensions procfs support is auto-selected
based on PROC_FS and anything that requires the wext core
(i.e. WIRELESS_EXT or CFG80211_WEXT).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code should never use private driver data, but
sometimes we need a backpointer so just stuff it on
the common ath struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows for hw support to be enabled for ar9271.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code for Atheros 802.11n hardware is commmon between
different chipsets. This moves this code into a separate
module, the next expected user of this code will be
the ath9k_htc module.
The ath9k/ dir is now selected by ATH9K_HW, an option which
gets selected by either ath9k or ath9k_htc, but remains
invisible for user menuconfig configuration. If either
ath9k or ath9k_htc will be compiled into the kernel
ath9k_hw will also be compiled in.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI and debug code will not be shared between ath9k and
ath9k_htc, so make that code use the common read/write ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commenting unused functions lpphy_restore_dig_flt_state and
lpphy_disable_rx_gain_override, may be we need these functions in future.
This also fixed following compilation warnings :
CC [M] drivers/net/wireless/b43/phy_lp.o
drivers/net/wireless/b43/phy_lp.c:383: warning: ‘lpphy_restore_dig_flt_state’ defined but not used
drivers/net/wireless/b43/phy_lp.c:891: warning: ‘lpphy_disable_rx_gain_override’ defined but not used
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since Johannes' "iwlwifi: improve scan support" iwlwifi
no longer needs any of lib80211's functions or definitions.
This patch updates iwlwifi's Kconfig _selections_ and
removes all left lib80211.h inclusions from the source files.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Get power table offset from the EEPROM instead of using
a hardcoded value of -5 if the EEPROM rev is >= 21.
* Add support in the 4k eeprom code for tx power offset
in case we have a 4k AR9280 implementation.
* Fix tx power accuracy at high powers.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has to be done if the EEPROM supports FCC Midband
capability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce PLL Settle time and eliminate redundant PLL calls. Also reduce
the LoadNF timeout from 10 msec to 250usec as the 10 msec timeout was
hit with AR9285 in some cases.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clearing a local variable is unnecessary.
Get rid of it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Move 0xa274 and 0xa27c to the top of tx_gain table.
* Update initvals to fix random failure of noise floor calibration.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR5416 chipsets, clearing RTC_RESET_EN when setting
the chip to SLEEP mode results in high power consumption.
This patch fixes this issue by not clearing it for AR5416.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current channel is between 2412 and 2472 MHz and if the channel is
changing to 2484 MHz, then the registers 0xa1f4, 0xa1f8 and 0xa1fc need to be
programmed to the "japan_2484" values. Conversely, if the current channel
is 2484 MHz and if the channel is changing to one between 2412 and 2472 MHz, then
the three registers need to be programmed to the "normal" values.
This is needed for compliance with Japanese regulatory requirements.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Prevent divide-by-zero errors in IQ Calibration.
* Do not run temperature compensation if initPDADC or currPDADC is zero.
* Also, introduce a separate function for handling OLC for AR9287.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar9170_op_get_tsf: handle a carry from TSF_L into TSF_H
by reading TSF_H twice.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add heavy clip handling for 2.4GHz only (similar to the vendor driver).
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some coding style issues and moves MAX_RATE_POWER into hw.h
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module firmware information of 1000 series is missing from iwlagn.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using powersave while idle saves a lot of power, but
we've had problems with this on some cards (5150 has
been reported to be problematic). However, on the new
6000 series we're seeing no problems, so for now let
that hardware benefit from idle mode, we can look at
the problems with other hardware one by one and then
enable those once we figure out the problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding support of Chain Noise Calibration for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When instructing the microcode to use just a single
chain when we have power saving enabled, we should
also tell the AP that we are doing SM powersave.
However, using a single chain doesn't actually have
any power saving advantage while idle -- measurements
show that the power consumption is no different when
using one vs. two or three chains.
Therefore, always instruct the microcode to use all
chains.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never have four chains, but let's fix the typo
while we noticed it. You count 0, 1, 2, 3, not
0, 1, 2, 4 :)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Today's implementation allow LED to blink based on the traffic
condition. We introduce an additional LED mode that reflects the RF
state.
The supported LED modes after this are:
IWL_LED_BLINK (current/default) - blink rate based on current Tx/Rx
traffic
IWL_LED_RF_STATE (new) -
LED OFF: No power/RF disabled, the LED is emitting no light
LED ON: Powered/RF enabled, the LED is emitting light
in a stable non-flashing state.
In order to provide the flexibility to support different LED
behavior per user/system preference we add "led_mode" iwlcore module
parameter.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PCI Subsystem ID for 60x0 series based on HW SKU. Adding new SKU
for "ABG" and "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PCI Subsystem ID for 1000 series based on HW SKU. Adding new SKU
for "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for uCode to select the valid antennas for transmit, driver
need to configure the allowed tx antennas through host command.
The TX_ANT_CONFIGURATION_CMD should be used for 5000 series and up
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current rate scale algorithm fluctuates between different MIMO modes fairly
rapidly, causing widely varying performance. These fluctuations occur because in
the rate_scale tables for expected throughput the values are not very different
for different modes.
However, when aggregation is turned on and MAC overhead is reduced, the
expected throughput for different MIMO modes grows and different modes have
vastly different performance. Add expected throughput tables for this case.
We also need to keep track of aggregation status per-station, so we add the
"is_agg" field to struct lq_sta.
Also includes cleanup of comments and variable names in/around the affected
code.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OR-in AMPDU flags rather than assigning them. This lets the TX status for
aggregated packets be processed by rs_tx_status.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cut down on redundant code, reorganize structure, and add/improve comments.
Should contain no functional changes.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcode module parameter's permissions, use pre-defined.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update EEPROM version requirement for 1000 and 6000 series of NIC
for EEPROM version verification.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow user to change protection mechanism for HT between RTS/CTS and
CTS-to-self through sysfs:
Show current protection mechanism for HT
cat /sys/class/net/wlan0/device/rts_ht_protection
Change protection mechanism for HT (only allowed while not-associated)
CTS-to-self:
echo 0 > /sys/class/net/wlan0/device/rts_ht_protection
RTS/CTS:
echo 1 > /sys/class/net/wlan0/device/rts_ht_protection
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chain settings we currently use in iwlwifi are
rather confusing -- and we also go by the wrong
settings entirely under certain circumstances. To
clean it up, create a new variable in the current
HT config -- single_chain_sufficient -- that tells
us whether we need more than one chain. Calculate
that based on the AP and operating mode (no IBSS
HT implemented -- so no need for multiple chains,
for station mode we use the AP's capabilities).
Additionally, since APs always send disabled SM PS
mode, keeping track of their sm_ps mode isn't very
useful -- doubly not so for our _own_ RX config
since that should depend on our, not the AP's, SM
PS mode.
Finally, document that our configuration of the
number of RX chains used is currently wrong when
in powersave (by adding a comment).
All together this removes the two remaining items
in struct iwl_ht_config that were done wrong there.
For the future, the number of RX chains and some
SM PS handshaking needs to be added to mac80211,
which then needs to tell us, and the new variable
current_ht_config.single_chain_sufficient should
also be calculated by mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show version number along with dumping NVM data, the version information
being removed from sysfs, add it back to debugfs to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Halperin pointed out that the naming
here is rather inconsistent with at least 3
different names being used for one thing in
different contexts. Rename the struct to
iwl_ht_config (rather than iwl_ht_info) and
use ht_conf as a variable for it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust led blink rate to compensate on a MAC Clock difference on every
HW. Led blink rate analysis showed an average deviation of 0% on 3945,
5% on 4965 HW and 20% on 5000 series and up.
Need to compensate on the led on/off time per HW according to the
deviation to achieve the desired led frequency
The calculation is: (100-averageDeviation)/100 * blinkTime
For code efficiency the calculation will be:
compensation = (100 - averageDeviation) * 64 / 100
NewBlinkTime = (compensation * BlinkTime) / 64
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
is_ht can be bool instead of u8, and there's
no need to use IWL_CHANNEL_WIDTH_* constants
in supported_chan_width when that could just
be named is_40mhz instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separate set_hw_params() function for 6000
series from 5000/1000 series because:
1) 6000 series use different set of sensitivity range table
2) 6000 series has different uCode image size
Also include the new sensitivity parameters needed by sensitivity
algorithm.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different NIC has different requirements for configuration. Currently all
5000 series hardware and later share the same configuration function even
though they do not need the same configurations. Fix this by separating the
needed configuration actions for each hardware model.
.5000 series: L1-ASPM H/W bug work-around
configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
work-around for NIC get stuck after early PCIe power off
.1000 series: write CSR_HW_IF_CONFIG_REG for uCode use
setting digital SVR for 1000 card to 1.32V
.6000 series: configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
write CSR_GP_DRIVER_REG to indicate radio sku
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove few of the parameters not used and no longer valid in EEPROM.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify LED blink index table to include 1Mbps.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the last part to make ath9k hw code core driver agnostic.
I believe ath9k_htc can now use use the hw code unmodified.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac.c is now core driver independent.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code will be shared between ath9k and ath9k_htc.
Just a few more files are left to clean up, mark them as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used just to determine how to program the MAC,
either for 20 MHz operation of 40 MHz so just use conf_is_ht40()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was for supporting 25 MHz spacing for HT40, this is not used
as we use 20 MHz spacing instead for HT40 as per 802.11n. The hardware
is capable of it though so we leave the phymode definition and EEPROM
parsing for it. If some experimenter wants to work on this stuff stuff
you can add an extension enabling bool on ath_common and perhaps some
debugfs knob to enable it. Keep in mind you'll also need to update the
phymode with the AR_PHY_FC_DYN2040_EXT_CH which has been left on the
driver.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k uses this for now, ath9k_htc is expected to re-use this
as well. We lave ath5k as is, but it certainly can also be
converted later.
The ath9k module parameter and debugfs entry is kept.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of it on hw code in ath9k to avoid
using the ath9k ath_softc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also make ath5k and ath9k use it, and share register definitions.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only common ath read/write ops go through the common ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can propagate better errors upon failed hw initialization,
and set up the ath_common structure for attach purposes. This
will become important once we start using the ath_common
for read/write ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In an effort to make hw code driver core agnostic read
and write operations are defined on the ath_common structure.
This patch adds that and makes ath9k use it. This allows
drivers like ath9k_htc to define its own read/write ops and
still rely on the same hw code. This also paves the way for
sharing code between ath9k/ath5k/ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We disable ASPM when enabling bluetooth coexistance. Disabling
ASPM is a bus specific operation. In the future other buses may
support bluetooth coexistance, an example is USB. To this end
move the current routine which disables ASPM into pci.c, and declare
it the PCI bt_coex_prep() helper. Additionally, since ASPM is
a PCI-Express primitive ensure we don't ever try to muck with ASPM
registers on non PCI-express devices.
This also cleans up hw.c to not include bus specific headers or
utilities.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ensures that we can access common on hw related code
independent of the driver core.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse warning:
CHECK drivers/net/wireless/ath/ath5k/attach.c
drivers/net/wireless/ath/ath5k/attach.c:288:42: warning: symbol 'ee' shadows an earlier one
drivers/net/wireless/ath/ath5k/attach.c:109:34: originally declared here
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ah_sta_id was really being used as the macaddr.
ath5k still does not use the association ID now passed
up by mac80211, that can be fixed later.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are common amongst ath9k and ath5k, so put them into the
common structure and make ath9k to use it. ar9170 can use macaddr,
and curbssid. We'll change ath5k and ar9170 separately.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the already provided helper instead of rewriting the code
required in place.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The same code was being implemented on reset for setting the bssidmask,
instead just use the already provided helper.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Historically some macro helpers have been users for this,
AR5K_LOW_ID() and AR5K_HIGH_ID(), use upstream unaligned
helpers instead. This applid to ath5k and ar9170. ath9k
already uses this.
Worth noting is ath5k uses an ah_sta_id but that is already
the MAC address combined with the associaiton ID, ah_sta_id
is really ETH_ALEN in size.
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Nick Kossifidis <mick@madwifi-project.org>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used by both ath5k and ath9k to set the first bssid mask.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_setpower_nolock --> ath9k_hw_setpower()
ath9k_hw_setpower() --> ath9k_setpower()
Also change the param for ath9k_setpower() to pass the ath_softc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_setpower() is a core driver helper with locking
protection. Locking protection should be left to the driver
core, not the hw code. Hardware code no longer contends for
locking when it needs to wake up the chip or put it to sleep.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the TSF is reset power save state is disabled and
then restored. The helpers to disable power save and restore
it use a lock provided by the driver core. Move the callers
of the helpers outside of the hw code.
We reset the TSF when mac80211 tells us and on the beacon.c
helper ath9k_hw_beaconinit() when it is made explicitly required.
Add a helper on beacon.c which will deal with ps awake/restore
if we need to reset the TSF upon ath9k_hw_beaconinit().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also just pass the ath_hw as the parameter.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are only used by btcoex.c on one routine, so stuff them
into that file.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After some necessary cleanups we now move ath9k_hw_btcoex_set_weight()
to where it belongs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The second argument is always the hardware bt coex struct, so
remove it, and rename the function on the path with a ath9k_ prefix.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
btcoex_scheme is already part of a btcoex struct, its implied
this is btcoex related.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bt_stomp_type defines the bt coex weight, it has a one-to-one
mapping. In the future we may want to just use the weight directly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whether or not bluetooth coex has been enabled is a hardware
state and only the hardware helpers will be able to set this.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One for 2-wire and another for 3-wire.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keep on btcoex.c only hardware access helpers, move the
driver core specific code to main.c. To accomplish
this we had to split ath_init_btcoex_info() into two parts,
the driver core part -- ath_init_btcoex_timer() and the hw
specific part -- ath9k_hw_init_btcoex_hw_info(). This
highlights how ath_gen_timer is part of the driver core, not
hw related, so stuff that into ath_btcoex struct.
The ath9k_hw_btcoex_init() code is now put inline on
ath_init_softc() through a switch to it easier to follow,
since we did that we can now call ath_tx_get_qnum() from
the main.c instead of btcoex.c
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a helper for 2-wire and another for 3-wire.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now access it via the ath_hw declare the ath_hw pointer
at the header of some routines and se it. ath9k.h no longer needs to
access btcoex.h and to adjust for this move ath_btcoex_set_weight()
into btcoex.h and instead give main.c a helper for setting initial
values upon drv_start()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is some bluetooth coexistance data which is driver
specific, stuff that into its own structure.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DPRINTF() is used in hw specific related code, as such
ensure we don't rely on the private driver core ath_softc
struct when calling it. Drivers can then implement their
own DPRINTF() as they see fit.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The DMA-API debugging facility complains about b43 mapping memory from
stack for SDIO-based cards.
Indeed, b43 currently allocates the PIO RX/TX header and tail buffers
from stack. The solution here is to use heap-allocated buffers instead.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In Bugzilla No. 14181, a PowerMac G4 crashes on ifdown or
module unload because the rfkill polling has not been stopped.
For the x86 architectures, the attempt to reach a now unmapped
register is not fatal as it is on PPC.
(Includes "b43: Fix locking problem when stopping rfkill polling". -- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A logical of shifts to the left doesn't make sense.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
User-visible messages should use formatted MAC addresses ("00:01:...")
rather than raw ("0001...") so they match other parts of the system.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: ilw@linux.intel.com
CC: linux-wireless@vger.kernel.org
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix IRQ mask sanity check for physically pulled device.
Tested-by: Andrew Price <andy@andrewprice.me.uk>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return type of abs() was recently changed from int to long. With
min()'s type checking we thus need to make sure that values of the same
type are compared.
This fixes:
CC [M] drivers/net/wireless/iwlwifi/iwl-5000.o
drivers/net/wireless/iwlwifi/iwl-5000.c: In function ‘iwl5000_gain_computation’:
drivers/net/wireless/iwlwifi/iwl-5000.c:320: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes following on big endian systems:
CC [M] drivers/net/wireless/iwlwifi/iwl-rx.o
drivers/net/wireless/iwlwifi/iwl-rx.c: In function ‘iwl_rx_reply_rx’:
drivers/net/wireless/iwlwifi/iwl-rx.c:1029: warning: integer overflow in
expression
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the correct EEPROM offset for enhance tx power for 6000 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The address stored in the next link address is a word address but when
reading the OTP blocks, a byte address is used. Also if the blocks are
full and the last link pointer is not zero, then none of the blocks are
valid so return an error.
The algorithm is simply valid blocks have a next address and that
address's contents is zero.
Using the wrong address for the next link address gets arbitrary data,
obviously. In cases seen, the first block is considered valid when it is not.
If the block has in fact been invalidated there may be old data or
there may be no data, bad data, or partial data, there is no way of
telling. Without this patch it is possible that a device with valid OTP data
is unable to work.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't use struct wldev after detach. This fixes an oops on access.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only 128 buffer descriptors are supported in the core. Limit the
number in case we have more memory.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enabled the ethoc to allocate system memory as buffer
when there is no dedicated buffer memory.
Some hardware designs may not have dedicated buffer memory such as
on chip or off chip SRAM. In this case, only one memory resource is
supplied in the platform data instead of two. Then a DMA buffer can
be allocated from system memory and used for the transfer.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet buffer is allocated at 4 bytes boundary, but the IP header
length and version bits is located at byte 14. These bit fields access
as 32 bits word and caused exception on processors that do not support
unaligned access.
The patch adds 2 bytes offset to make the bit fields word aligned.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer address in buffer descriptors is physical address. The
pointer that processor used to access packet is virtual address.
Though the higher bits of pointer address used by the MAC may be
truncated to zero in special case, it is not always true in larger
designs.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should be max() instead of min(). Use 1/4 of available
descriptors for tx, and there should be at least 2 tx
descriptors.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
in update_rx_stats() the RX_OVERLEN bit is set twice, replace it by RX_RUNT.
in au1000_rx() the RX_MISSED_FRAME bit was tested a few lines earlier already
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The closing parenthesis was not on the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all pasemi mac interfaces can have a phy attached.
For example, XAUI has no phy and phydev is NULL for it.
In this case ethtool get settings causes kernel crash.
Fix it by returning -EOPNOTSUPP if there's no PHY attached.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Radensky noted that chip resets were generating stack trace dumps.
This is because the driver is attempting to acquire the mdio bus mutex
while holding the tp->lock spinlock. The fix is to change the code such
that every phy access takes the tp->lock spinlock instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter doesnot need to maintain a copy of net_device_stats.
Use the one already available in net_device. This patch takes care of the same.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data center bridging ops structure can be const
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All usages of structure net_proto_ops should be declared const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive_buf methods of the N_PPP and N_SYNC_PPP line disciplines,
ppp_asynctty_receive() and ppp_sync_receive(), call tty_unthrottle()
which may sleep. Fix the comments claiming otherwise.
Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases there is not desirable to switch back to primary interface when
it's link recovers and rather stay with currently active one. We need to avoid
packetloss as much as we can in some cases. This is solved by introducing
primary_reselect option. Note that enslaved primary slave is set as current
active no matter what.
Patch modified by Jay Vosburgh as follows: fixed bug in action
after change of option setting via sysfs, revised the documentation
update, and bumped the bonding version number.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for a bug which was a result of wrong use of checksum offload flag.
The status of tx-checksumming was not changed from on to off
after a 'ethtool -K <ifname> tx off' operation.
Use the proper checksum offload flag NETIF_F_HW_CSUM instead of
NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM.
Patch is against net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66.
This patch fixes this typo. Patch against net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While updating the statistics to be passed via the get_stats,
tx multicast frames were being accounted instead of rx multicast frames.
This patch fixes the bug. This patch is against the net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of spinlock and private mutex usage for exclusive access to the
HW semaphore register. rtnl_lock already creates exclusive access to
this register in all driver API.
Add rtnl to firmware worker threads that also use the HW semaphore register.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that we are not already polling firmware events before we queue the
firmware event worker, then disable firmware interrupts.
Otherwise we can queue the same event multiple times.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Allow multiple functions with INTA.
- Removed the condition to allow only one vpath with INTA
- Ensure that the alarm bit in titan_mask_all_int register is cleared when
driver exits.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added a function to check if FCS stripping is disabled by the firmware, if
it is not disabled fail driver load.
- By default FCS stripping is disabled by the firmware. With this assumption
driver decrements the indicated packet length by 4 bytes(FCS length).
- This patch ensures that FCS stripping is disabled during driver load time.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removed the wrr_rebalance function
- This feature is not supported by the ASIC, hence removing the related code.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a crash in PAE system due to wrong typecasting.
- On PAE system size_t is unsigned int which is 32bit. Avoid casting
64 bit address to 32 bit
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removed accessing GENDMA_INT register
- This allowed the firmware to perform a generic DMA write to host memory.
This feature is not supported by the ASIC, this patch removes access to
GENDMA_INT register.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update driver_config->vpath_per_dev for each function in probe.
- vpath_per_device specifies number of vpaths supported for each function/device. The
current code was updating vpath_per_device only for physical device, however this has
to be updated for each function also in case of a MF(Multi function) device.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- vxge driver was assuming function-0 is always the privilaged function. Now that
restriction has been removed any function can act as a privilaged function.
- This patch modifies the __vxge_hw_device_is_privilaged routine to not assume
function-0 as the privileged function.
- Recreated the patch by incorporating review comments from Dave Miller to
remove double slash in path names.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some switches that will do write combining when they see two
sequential regions written. In order to avoid any possible write combining
issues it is necessary to add a flush after writing each piece of a rar
register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This update adds additional exception handling to the phy code to handle
situations where it may be called incorrectly. In addition it adds some
bounds checking to the cable length checks to prevent an array overrun in
the event that the hardware returned a different value than expected.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a retry to phy reads in the event of failure. The original
code broke out of the loop on failure and this is a mistake as we should be
trying to do the read twice.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the generic portion of the copper link setup into a
seperate function in e1000_phy.c. This helps to reduce the size of
copper_link_setup_82575 and make it a bit more readable.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb doesn't have any devices that use a microwire interface for NVM. As
such the code related to this can be removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows us to treat the alternate mac address as though it is the
physical address on the adapter. This is accomplished by letting the
alt_mac_address function to only fail on an NVM error. If no errors occur
and the alternate mac address is not present then RAR0 is read as the
default mac address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mailbox timeout routines need to be updated as they were not correctly
handling the case of a mailbox timeout and could cause issues with long
delays when used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the read and write mailbox functions need to acquire the mailbox lock.
Since that is the case we might as well combine both of the procedures into
one function so it is easier to maintain.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the device ID necessary to support the 82576NS SerDes
adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support functions such as vlan tag stripping when SR-IOV is
enabled any given packet must match at least one filter. However in the
case of promiscous mode being enabled on the PF the traffic routed to it
may not match any filters and is just sent to the PF by default. In order
to make certain that this traffic is processed we can set all bits in the
UTA registers to create a pseudo promiscous mode filter that accepts all
packets.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds igb_rar_qsel which sets the mac address and pool bits for a
given mac address in the receive address register table.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of sgmii support isn't correctly locking the
interfaces for reads/writes. This change pulls the read/write
functionality out of 82575.c and moves it to phy.c. In addition it
replaces the implementation in 82575.c with one that uses locking around
the relocated i2c interface calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current approach is just using a ?: type mechanism to set the phy
locking bit. This if fine for now but limits us to only 2. Switch to a
nested if statement for future compatiblity with more than 2 phys.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This update corrects the driver so that it handles duplex for serdes links
correctly instead of just forcing full duplex always.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a temp variable in the stats clearing path that isn't needed since
the results from the stats read can be immediately discared. Since it
isn't needed we might as well just drop it from the function call.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug that got introduced in commit 76998bc7.
During preparation of mcc wrb, req was being wrongly overwritten
and the flash operation was failing.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For usbnet devices with FLAG_WLAN and FLAG_WWAN set the proper device
type so that uevent contains the correct value. This then allows an easy
identification of the actual underlying technology of the Ethernet device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for usbnet based devices like CDC-Ether to indicate that they
are actually mobile broadband devices. In that case use wwan%d as default
interface name.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs,serial_cs:
add cis of National Semicondoctor's lan&modem mulitifunction pcmcia card,
NE2K, tamarack ethernet card,
and some serial card(COMpad2, COMpad4).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BIT for macro definitions wherever possible, remove
unused and redundant macros.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These string query operations were supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert the remaining
implementations.
Also remove calls to these operations to initialise drvinfo->n_stats.
The ethtool core code already does that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This string query operation was supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert tehuti's
implementation.
Also remove the dummy self-test name which was not used since tehuti
does not advertise any self-tests.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There appears to have been a mixup in the max supported jumbo frame size
between 82574 and 82583 which ended up disabling jumbo frames on the 82574
as a result. This patch swaps the two so that this issue is resolved.
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=14261
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds device support for the 82599 based X520 10GbE
Dual Port KX4 Mezzanine card.
Signed-off-by: Don Skidmore<donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add support for the 82599 Dual port Backplane
device (0x10f8). This device has the ability to link in serial (KR) and
parallel (KX4/KX) modes, depending on what the switch capabilities are in
the blade chassis.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (46 commits)
cnic: Fix NETDEV_UP event processing.
uvesafb/connector: Disallow unpliviged users to send netlink packets
pohmelfs/connector: Disallow unpliviged users to configure pohmelfs
dst/connector: Disallow unpliviged users to configure dst
dm/connector: Only process connector packages from privileged processes
connector: Removed the destruct_data callback since it is always kfree_skb()
connector/dm: Fixed a compilation warning
connector: Provide the sender's credentials to the callback
connector: Keep the skb in cn_callback_data
e1000e/igb/ixgbe: Don't report an error if devices don't support AER
net: Fix wrong sizeof
net: splice() from tcp to pipe should take into account O_NONBLOCK
net: Use sk_mark for routing lookup in more places
sky2: irqname based on pci address
skge: use unique IRQ name
IPv4 TCP fails to send window scale option when window scale is zero
net/ipv4/tcp.c: fix min() type mismatch warning
Kconfig: STRIP: Remove stale bits of STRIP help text
NET: mkiss: Fix typo
tg3: Remove prev_vlan_tag from struct tx_ring_info
...
This fixes the problem of not handling the NETDEV_UP event properly
during hot-plug or modprobe of bnx2 after cnic. The handling was
skipped by mistakenly using "else if" to check for the event.
Also update version to 2.0.1.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only error returned by pci_{en,dis}able_pcie_error_reporting() is
-EIO which simply means that Advanced Error Reporting is not supported.
There is no need to report that, so remove the error check from e1000e,
igb and ixgbe.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Which is why I have always preferred sizeof(struct foo) over
sizeof(var).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is based on Michal Schmidt fix for skge.
Most network drivers request their IRQ when the interface is activated.
sky2 does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:
1. modprobe sky2
The card is detected as eth0 and requests IRQ 17. Directory
/proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
Now 8139too requests IRQ 17.
The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
The fix is for sky2 to name the irq based on the pci device, as is done
by some other devices DRM, infiniband, ... ie. sky2@pci:0000:00:00
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most network drivers request their IRQ when the interface is activated.
skge does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:
1. modprobe skge
The card is detected as eth0 and requests IRQ 17. Directory
/proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
Now 8139too requests IRQ 17.
The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
...
And "ls /proc/irq/17" shows two subdirectories, both called eth0.
Fix it by using a unique name for skge's IRQ, based on the PCI address.
The naming from the example then looks like this:
$ grep skge /proc/interrupts
17: 169 IO-APIC-fasteoi skge@pci:0000:00:0a.0, eth0
irqbalance daemon will have to be taught to recognize "skge@" as an
Ethernet interrupt. This will be a one-liner addition in classify.c. I
will send a patch to irqbalance if this change is accepted.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove references to dead web site mosquitonet.Stanford.EDU.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This typo was introduced by 5793f4be23 on
October 14, 2005 ...
Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
prev_vlan_tag field is not used.
Patch saves 512*8 bytes per tx queue ring on 64bit arches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Matthew Carlson <mcarlson@broadcom.com>
The function virtnet_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alex Williamson <alex.williamson@hp.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sgiseeq_remove is defined using __exit, so don't use
__devexit_p but __exit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Wang Chen <wangchen@cn.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The function meth_remove is defined using __exit, so don't use __devexit_p
but __exit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Primary module parameter passed to bonding is pernament. That means if you
release the primary slave and enslave it again, it becomes the primary slave
again. But if you set primary slave via sysfs, the primary slave is only set
once and it's not remembered in bond->params structure. Therefore the setting is
lost after releasing the primary slave. This simple one-liner fixes this.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ccffad25b5 changed parameters for function
ixgbe_update_uc_addr_list_generic but parameter description was not updated.
This patch corrects it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vtp bit in RX completion descriptor could be wrongly set in
some skews of BladEngine. Ignore this bit if vtm is not set.
Resending because the previous patch was against net-next tree.
This patch is against the net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Alan Stern, there is still one issue with the driver:
we disable PCI IRQ on suspend, but other devices on the same IRQ
line might still need the IRQ enabled to suspend properly.
Nowadays, PCI core handles all power management work by itself, with
one condition though: if we use dev_pm_ops. So, rework the driver to
only quiesce 3c59x internal logic on suspend, while PCI core will
manage PCI device power state with IRQs disabled.
Suggested-by: Rafael J. Wysocki <rjw@sisk.pl>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first registration of ks8851 network driver with
MLL(address/data multiplexed) interface.
Signed-off-by : David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If allocation of the second ports fails, make sure that hw->ports
is not 2 otherwise we'll crash trying to access the second port.
This fix is copied from a similar fix in the sky2 driver (ca519274...),
but is untested, as I don't have a skge card.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`while (limit-- >= 0)' reaches -2 after the loop upon timeout.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to rtnl_lock() to before the internal call to
ql_adapter_down()/ql_adapter_up(). This prevents collisions that can
happen when recovering from an asic error.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ql_clear_routing_entries() takes/gives it's own hardware semaphore since
it is called from more than one place. ql_route_initialize() should
make this call and THEN take it's own semaphore before doing it's work.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATR support for UDP on 82599 needs to be redesigned, since the
current model doesn't make much sense. The fallout from having
it in though is it causes all UDP traffic to still compute the
ATR hashes on transmit, which are useless. This removal will
return upwards of 10% of relative computational overhead in
forwarding tests.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When LRO is enabled, the received packet and byte counters represent the
LRO'd packets, not the packets/bytes on the wire. The Intel 82599 NIC has
registers that keep count of the physical packets. Add these counters to
the ethtool stats. The byte counters are 36-bit, but the high 4 bits were
being ignored in the 2.6.31 ixgbe driver: Read those as well to allow
longer time between polling the stats to detect wraps.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of changes have gone in since the last version bump. Bump
it to reflect the changes.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Backplane flow control autonegotiation is currently broken for
ixgbe devices. This patch fixes the flow control issues
with clause 37 autoneg.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 has a different register offset for the Tx DCA control registers.
We disable relaxed ordering of the descriptor writebacks for Tx head
writeback, but didn't disable it properly for 82599. However, this
shouldn't be a visible issue, since ixgbe doesn't use Tx head writeback.
This patch just makes sure we're not doing blind writes to offsets we
don't expect.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides safety against negative optlen at the type
level instead of depending upon (sometimes non-trivial)
checks against this sprinkled all over the the place, in
each and every implementation.
Based upon work done by Arjan van de Ven and feedback
from Linus Torvalds.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
sony-laptop: re-read the rfkill state when resuming from suspend
sony-laptop: check for rfkill hard block at load time
wext: add back wireless/ dir in sysfs for cfg80211 interfaces
wext: Add bound checks for copy_from_user
mac80211: improve/fix mlme messages
cfg80211: always get BSS
iwlwifi: fix 3945 ucode info retrieval after failure
iwlwifi: fix memory leak in command queue handling
iwlwifi: fix debugfs buffer handling
cfg80211: don't set privacy w/o key
cfg80211: wext: don't display BSSID unless associated
net: Add explicit bound checks in net/socket.c
bridge: Fix double-free in br_add_if.
isdn: fix netjet/isdnhdlc build errors
atm: dereference of he_dev->rbps_virt in he_init_group()
ax25: Add missing dev_put in ax25_setsockopt
Revert "sit: stateless autoconf for isatap"
net: fix double skb free in dcbnl
net: fix nlmsg len size for skb when error bit is set.
net: fix vlan_get_size to include vlan_flags size
...
This patch fixes a embarrassing bug which was introduced by:
"[PATCH] ar9170: implement frequency calibration for one-stage/openfw"
The phy_data variable initialization has to done outside the for-loop
scope. This is because the for-loop uses u32 phy_data variable more
like a 4-byte field. But in each run only a single byte is calculated.
Therefore phy_data content needs to stay the same for at least 3 more
iterations, before the complete set can be uploaded.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thrustmaster FunAccess WIFI USB works with rt73usb with little
modification of rt73usb.c.
Tested with version 2.3.0 of driver.
Signed-off-by: Michal Szalata <szalat@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211_hwsim does not start transmitting Beacon frames when hostapd
is started for the first time and restarting hostapd fixes this. The
issue is caused by the config() handler not being able to start
beacon_timer when beacon interval is not yet known and
bss_info_changed() handler not starting the timer. This can be fixed by
making the bss_info_changed() update the timer.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On SDIO the PIO data register seems to be hardwired to LE. So
the MACCTL bit has no effect on the endianness.
So also use block-I/O for the last word of the packet. block-I/O is always LE.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hardware or uCode problem occurs driver captures significant
information from device to enable debugging. The format of this information
is different between 3945 and 4965 and later devices, yet currently the
3945 uses the 4965 and later format. Fix this by adding a new library call
that is initialized to the correct formatting routine based on device.
This moves the iwlagn event and error log handling back to iwl-agn.c to
make it part of iwlagn module.
Also remove the 3945 sysfs file that triggers dump of event log - there is
already a debugfs file that can do it for all drivers.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also free the array of command pointers and meta data of each
command buffer when command queue is freed.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We keep track of where to write into a buffer by keeping a count of how
much has been written so far. When writing to the buffer we thus take the
buffer pointer and adding the count of what has been written so far.
Keeping track of what has been written so far is done by incrementing
this number every time something is written to the buffer with how much has
been written at that time.
Currently this number is incremented incorrectly when using the
"hex_dump_to_buffer" call to add data to the buffer. Fix this by only
adding what has been added to the buffer in that call instead of what has
been added since beginning of buffer.
Issue was discovered and discussed during testing of
https://bugzilla.redhat.com/show_bug.cgi?id=464598 .
When a user views any of these files they will see something like:
[ 179.355202] ------------[ cut here ]------------
[ 179.355209] WARNING: at ../lib/vsprintf.c:989 vsnprintf+0x5ec/0x5f0()
[ 179.355212] Hardware name: VGN-Z540N
[ 179.355213] Modules linked in: i915 drm i2c_algo_bit i2c_core ipv6 acpi_cpufreq cpufreq_userspace cpufreq_powersave cpufreq_ondemand cpufreq_conservative cpufreq_stats freq_table container sbs sbshc arc4 ecb iwlagn iwlcore joydev led_class mac80211 af_packet pcmcia psmouse sony_laptop cfg80211 iTCO_wdt iTCO_vendor_support pcspkr serio_raw rfkill intel_agp video output tpm_infineon tpm tpm_bios button battery yenta_socket rsrc_nonstatic pcmcia_core processor ac evdev ext3 jbd mbcache sr_mod sg cdrom sd_mod ahci libata scsi_mod ehci_hcd uhci_hcd usbcore thermal fan thermal_sys
[ 179.355262] Pid: 5449, comm: cat Not tainted 2.6.31-wl-54419-ge881071 #62
[ 179.355264] Call Trace:
[ 179.355267] [<ffffffff811ad14c>] ? vsnprintf+0x5ec/0x5f0
[ 179.355271] [<ffffffff81041348>] warn_slowpath_common+0x78/0xd0
[ 179.355275] [<ffffffff810413af>] warn_slowpath_null+0xf/0x20
[ 179.355277] [<ffffffff811ad14c>] vsnprintf+0x5ec/0x5f0
[ 179.355280] [<ffffffff811ad23d>] ? scnprintf+0x5d/0x80
[ 179.355283] [<ffffffff811ad23d>] scnprintf+0x5d/0x80
[ 179.355286] [<ffffffff811aed29>] ? hex_dump_to_buffer+0x189/0x340
[ 179.355290] [<ffffffff810e91d7>] ? __kmalloc+0x207/0x260
[ 179.355303] [<ffffffffa02a02f8>] iwl_dbgfs_nvm_read+0xe8/0x220 [iwlcore]
[ 179.355306] [<ffffffff811a9b62>] ? __up_read+0x92/0xb0
[ 179.355310] [<ffffffff810f0988>] vfs_read+0xc8/0x1a0
[ 179.355313] [<ffffffff810f0b50>] sys_read+0x50/0x90
[ 179.355316] [<ffffffff8100bd6b>] system_call_fastpath+0x16/0x1b
[ 179.355319] ---[ end trace 2383d0d5e0752ca0 ]---
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function e1000_enable_tx_pkt_filtering() was removed in
a previous cleanup patch. this removes the no longer used
prototype.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a couple of functions needed to be removed/declared static
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eerd and eewr don't exist on pre PCIe devices
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A large whitespace change to e1000_hw.[ch] in order to update it to kernel coding
style (by running lindent). Updated function header comments into kdoc style.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter was being assigned twice, also clarified variable name and unwrapped
line.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes a bug that occurs when routing packets and simultaneously
changing the mtu. the rx_buffer_len variable is used during the rx cleanup
and if that changes on the fly without stopping traffic bad things happen
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) 82544 does not need last_tx_tso workaround, it interferes with the 82544
workaround too
2) 82544 hang workaround was using the address of the page struct instead of
the physical address as its "workaround decider" not sure how that ever worked
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix closes a race where the adapter can be shutting down while
hard_start_xmit is being called and interrupts are being handled.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000 was using one particular way to detect link, but with the advent
of some of the newer hardware designs using SERDES connections, tests
for link must completely cover all cases.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
there were some hotplug cases that made timers still run after the driver
had been removed, make sure to stop all the timers and not allow racy
reschedules.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we can use netif_tx_disable now because LLTX has been removed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after removal of pcie, need to remove some unnecessary functions
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch is the first in a series of clean up patches for e1000 to drop
unused code, and update the driver to kernel spec, and then, to update the
driver to have all available bug fixes.
Call it the e1000 weight loss plan.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove asm/atomic.h inclusion from kref.h -- not needed, linux/types.h
is enough for atomic_t
* remove linux/kref.h inclusion from files which do not need it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
at91_can: Forgotten git 'add' of at91_can.c
TI Davinci EMAC: Fix in vector definition for EMAC_VERSION_2
ax25: Fix ax25_cb refcounting in ax25_ctl_ioctl
virtio_net: Check for room in the vq before adding buffer
virtio_net: avoid (most) NETDEV_TX_BUSY by stopping queue early.
virtio_net: formalize skb_vnet_hdr
virtio_net: don't free buffers in xmit ring
virtio_net: return NETDEV_TX_BUSY instead of queueing an extra skb.
virtio_net: skb_orphan() and nf_reset() in xmit path.
In the emac_poll function when looking for interrupt status masks
correct definition must be chosen based on EMAC_VERSION(the bit
mask has changed from version 1 to version 2).
Signed-off-by: Sriram <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (94 commits)
genetlink: fix netns vs. netlink table locking (2)
3c59x: Get rid of "Trying to free already-free IRQ"
tunnel: eliminate recursion field
ems_pci: fix size of CAN controllers BAR mapping for CPC-PCI v2
net: fix htmldocs sunrpc, clnt.c
Phonet: error on broadcast sending (unimplemented)
Phonet: fix race for port number in concurrent bind()
pktgen: better scheduler friendliness
pktgen: T_TERMINATE flag is unused
ipv4: check optlen for IP_MULTICAST_IF option
ath9k: Initialize txgain and rxgain for newer AR9287 chipsets.
iwlagn: fix panic in iwl{5000,4965}_rx_reply_tx
ath9k: Fix RFKILL bugs
drivers/net/wireless: Use usb_endpoint_dir_out
cfg80211: don't overwrite privacy setting
wl12xx: fix kconfig/link errors
rt2x00: fix the definition of rt2x00crypto_rx_insert_iv
iwlwifi: reduce noise when skb allocation fails
iwlwifi: do not send sync command while holding spinlock
mac80211: fix DTIM setting
...
* 'for-linus' of git://repo.or.cz/cris-mirror:
CRIS: Cleanup linker script using new linker script macros.
ARRAY_SIZE changes
CRIS: convert to asm-generic/hardirq.h
CRISv10: Don't autonegotiate if autonegotiation is off
CRIS: fix defconfig build failure
CRIS: add pgprot_noncached
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (103 commits)
ARM: 5719/1: [AT91] Fix AC97 breakage
ARM: 5721/1: MMCI enable the use of a regulator
ARM: 5720/1: Move MMCI header to amba include dir
ARM: 5718/1: Sane busids for RealView board components
ARM: 5715/1: Make kprobes unregistration SMP safe
ARM: 5711/1: locomo.c: CodingStyle cleanups
ARM: 5710/1: at91: add AC97 support to at91sam9rl and at91sam9rlek board
ARM: 5709/1: at91: add AC97 support to at91sam9g45 series and at91sam9m10g45ek board
ARM: 5621/1: at91/dmaengine: integration of at_hdmac driver in at91sam9g45 series
ARM: 5620/1: at91/dmaengine: integration of at_hdmac driver in at91sam9rl
ARM: Add support for checking access permissions on prefetch aborts
ARM: Separate out access error checking
ARM: Ensure correct might_sleep() check in pagefault path
ARM: Update page fault handling for new OOM techniques
ARM: Provide definitions and helpers for decoding the FSR register
ARM: 5712/1: SA1100: initialise spinlock in DMA code
ARM: s3c: fix check of index into s3c_gpios[]
ARM: spitz: fix touchscreen max presure
ARM: STMP3xxx: deallocation with negative index of descriptors[]
Thumb-2: Correctly handle undefined instructions in the kernel
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Don't turn on carrier for a non-active port
IB/mthca: Fix access to freed memory in catastrophic event handling
mlx4_core: Pass cache line size to device FW
RDMA/nes: Remove duplicate .ndo_set_mac_address field initialization
IB/mad: Fix lock-lock-timer deadlock in RMPP code
Following trace pops up if we try to suspend with 3c59x ethernet NIC
brought down:
root@b1:~# ifconfig eth16 down
root@b1:~# echo mem > /sys/power/state
...
3c59x 0000:00:10.0: suspend
3c59x 0000:00:10.0: PME# disabled
Trying to free already-free IRQ 48
------------[ cut here ]------------
Badness at c00554e4 [verbose debug info unavailable]
NIP: c00554e4 LR: c00554e4 CTR: c019a098
REGS: c7975c60 TRAP: 0700 Not tainted (2.6.31-rc4)
MSR: 00021032 <ME,CE,IR,DR> CR: 28242422 XER: 20000000
TASK = c79cb0c0[1746] 'bash' THREAD: c7974000
...
NIP [c00554e4] __free_irq+0x108/0x1b0
LR [c00554e4] __free_irq+0x108/0x1b0
Call Trace:
[c7975d10] [c00554e4] __free_irq+0x108/0x1b0 (unreliable)
[c7975d30] [c005559c] free_irq+0x10/0x24
[c7975d40] [c01e21ec] vortex_suspend+0x70/0xc4
[c7975d60] [c017e584] pci_legacy_suspend+0x58/0x100
This is because the driver manages interrupts without checking for
netif_running().
Though, there are few other issues with suspend/resume in this driver.
The intention of calling free_irq() in suspend() was to avoid any
possible spurious interrupts (see commit 5b039e681b
"3c59x PM fixes"). But,
- On resume, the driver was requesting IRQ just after pci_set_master(),
but before vortex_up() (which actually resets 3c59x chips).
- Issuing free_irq() on a shared IRQ doesn't guarantee that a buggy
HW won't trigger spurious interrupts in another driver that
requested the same interrupt. So, if we want to protect from
unexpected interrupts, then on suspend we should issue disable_irq(),
not free_irq().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver mapped only 128 bytes of the CAN controller address space when a
CPC-PCI v2 was detected (incl. CPC-104P). This patch will fix it by always
mapping the whole address space (4096 bytes on all boards) of the
corresponding PCI BAR.
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ConnectX can work more efficiently if the CPU cache line size is passed
to it with the INIT_HCA firmware command.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It's unused.
It isn't needed -- read or write flag is already passed and sysctl
shouldn't care about the rest.
It _was_ used in two places at arch/frv for some reason.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Saves us one cycle of alloc-add-free if the queue was full.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (modified)
Now we can tell the theoretical capacity remaining in the output
queue, virtio_net can waste entries by stopping the queue early.
It doesn't work in the case of indirect buffers and kmalloc failure,
but that's rare (we could drop the packet in that case, but other
drivers return TX_BUSY for similar reasons).
For the record, I think this patch reflects poorly on the linux
network API.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dinesh Subhraveti <dineshs@us.ibm.com>
We put the virtio_net_hdr into the skb's cb region; turn this into a
union to clean up the code slightly and allow future expansion.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Dinesh Subhraveti <dineshs@us.ibm.com>
The virtio_net driver is complicated by the two methods of freeing old
xmit buffers (in addition to freeing old ones at the start of the xmit
path).
The original code used a 1/10 second timer attached to xmit_free(),
reset on every xmit. Before we orphaned skbs on xmit, the
transmitting userspace could block with a full socket until the timer
fired, the skb destructor was called, and they were re-woken.
So we added the VIRTIO_F_NOTIFY_ON_EMPTY feature: supporting devices
send an interrupt (even if normally suppressed) on an empty xmit ring
which makes us schedule xmit_tasklet(). This was a benchmark win.
Unfortunately, VIRTIO_F_NOTIFY_ON_EMPTY makes quite a lot of work: a
host which is faster than the guest will fire the interrupt every xmit
packet (slowing the guest down further). Attempting mitigation in the
host adds overhead of userspace timers (possibly with the additional
pain of signals), and risks increasing latency anyway if you get it
wrong.
In practice, this effect was masked by benchmarks which take advantage
of GSO (with its inherent transmit batching), but it's still there.
Now we orphan xmitted skbs, the pressure is off: remove both paths and
no longer request VIRTIO_F_NOTIFY_ON_EMPTY. Note that the current
QEMU will notify us even if we don't negotiate this feature (legal,
but suboptimal); a patch is outstanding to improve that.
Move the skb_orphan/nf_reset to after we've done the send and notified
the other end, for a slight optimization.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mark McLoughlin <markmc@redhat.com>
This effectively reverts 99ffc696d1
"virtio: wean net driver off NETDEV_TX_BUSY".
The complexity of queuing an skb (setting a tasklet to re-xmit) is
questionable, especially once we get rid of the other reason for the
tasklet in the next patch.
If the skb won't fit in the tx queue, just return NETDEV_TX_BUSY.
This is frowned upon, so a followup patch uses a more complex solution.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
The complex transmit free logic was introduced to avoid hangs on
removing the ip_conntrack module and also because drivers aren't
generally supposed to keep stale skbs for unbounded times.
After some debate, it was decided that while doing skb_orphan()
generally is a rat's nest, we can do it in this driver. Following
patches take advantage of this.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Remove open-coded zalloc_cpumask_var() and zalloc_cpumask_var_node().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (142 commits)
USB: Fix sysfs paths in documentation
USB: skeleton: fix coding style issues.
USB: O_NONBLOCK in read path of skeleton
USB: make usb-skeleton honor O_NONBLOCK in write path
USB: skel_read really sucks royally
USB: Add hub descriptor update hook for xHCI
USB: xhci: Support USB hubs.
USB: xhci: Set multi-TT field for LS/FS devices under hubs.
USB: xhci: Set route string for all devices.
USB: xhci: Fix command wait list handling.
USB: xhci: Change how xHCI commands are handled.
USB: xhci: Refactor input device context setup.
USB: xhci: Endpoint representation refactoring.
USB: gadget: ether needs to select CRC32
USB: fix USBTMC get_capabilities success handling
USB: fix missing error check in probing
USB: usbfs: add USBDEVFS_URB_BULK_CONTINUATION flag
USB: support for autosuspend in sierra while online
USB: ehci-dbgp,ehci: Allow dbpg to work with suspend/resume
USB: ehci-dbgp,documentation: Documentation updates for ehci-dbgp
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: don't force VIRTIO_F_NOTIFY_ON_EMPTY
lguest: cleanup for map_switcher()
lguest: use PGDIR_SHIFT for PAE code to allow different PAGE_OFFSET
lguest: use set_pte/set_pmd uniformly for real page table entries
lguest: move panic notifier registration to its expected place.
virtio_blk: add support for cache flush
virtio: add virtio IDs file
virtio: get rid of redundant VIRTIO_ID_9P definition
virtio: make add_buf return capacity remaining
virtio_pci: minor MSI-X cleanups
In some cases firmware can give us bad value of index in transmit
buffers array. This patch add sanity check for such values and return
from processing function instantly when it happens.
https://bugzilla.redhat.com/show_bug.cgi?id=521931
Patch was tested by reporter on iwl5000. I think check can be also
helpful for 4965.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes 2 issues in RFKILL:
* Calling wiphy_rfkill_stop_polling() in ath9k_stop
would mean that the driver cannot report HW status
when the radio is re-enabled. Move this to ath_detach().
* Calling ath_radio_{enable/disable} without checking the current
state results in ath_radio_enable() being called repeatedly
for every invocation of rfkill_poll(). This is not needed
in any case since wiphy_rfkill_set_hw_state() would call
->stop() if the radio has been disabled.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the usb_endpoint_dir_out API function. Note that the use of
USB_TYPE_MASK in the original code is incorrect; it results in a test that
is always false.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
struct usb_endpoint_descriptor *endpoint;
expression E;
@@
- (endpoint->bEndpointAddress & E) == USB_DIR_OUT
+ usb_endpoint_dir_out(endpoint)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"boolean" converts a module dependency (MAC80211=m) to YES,
then the WL12XX driver can be built-in instead of only
modular, which leads to linker errors:
wl1271_main.c:(.text+0x11177d): undefined reference to `ieee80211_frequency_to_channel'
wl1271_main.c:(.text+0x111adc): undefined reference to `ieee80211_stop_queues'
wl1271_main.c:(.text+0x112005): undefined reference to `ieee80211_scan_completed'
(.text+0x1139c8): undefined reference to `ieee80211_scan_completed'
(.text+0x113bb0): undefined reference to `ieee80211_tx_status'
(.text+0x113e53): undefined reference to `ieee80211_stop_queues'
(.text+0x113e8d): undefined reference to `ieee80211_wake_queues'
(.text+0x113f3b): undefined reference to `ieee80211_tx_status'
(.text+0x113f60): undefined reference to `ieee80211_tx_status'
(.text+0x1140f0): undefined reference to `ieee80211_channel_to_frequency'
(.text+0x114153): undefined reference to `ieee80211_rx'
wl1271_main.c:(.devinit.text+0xca08): undefined reference to `ieee80211_alloc_hw'
wl1271_main.c:(.devinit.text+0xccf5): undefined reference to `ieee80211_register_hw'
wl1271_main.c:(.devinit.text+0xcd6b): undefined reference to `ieee80211_free_hw'
wl1271_main.c:(.devexit.text+0x1353): undefined reference to `ieee80211_unregister_hw'
wl1271_main.c:(.devexit.text+0x13c9): undefined reference to `ieee80211_free_hw'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the redundant l2pad parameter from the definition of
rt2x00crypto_rx_insert_iv which is used when only CONFIG_RT2500PCI but
none of the other rt2x00 family drivers is configured.
Signed-off-by: Andrew Price <andy@andrewprice.me.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replenishment of receive buffers is done in the tasklet handling
received frames as well as in a workqueue. When we are in the tasklet
we cannot sleep and thus attempt atomic skb allocations. It is generally
not a big problem if this fails since iwl_rx_allocate is always followed
by a call to iwl_rx_queue_restock which will queue the work to replenish
the buffers at a time when sleeping is allowed.
We thus add the __GFP_NOWARN to the skb allocation in iwl_rx_allocate to
reduce the noise if such an allocation fails while we still have enough
buffers. We do maintain the warning and the error message when we are low
on buffers to communicate to the user that there is a potential problem with
memory availability on system
This addresses issue reported upstream in thread "iwlagn: order 2 page
allocation failures" in
http://thread.gmane.org/gmane.linux.kernel.wireless.general/39187
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 10c994ca70e8e94bbc85a5bf13de5911ee8de4d2 "iwlwifi: fix remove key
error" fixed an error reported by mac80211 during interface down. The fix
involved changing an async command to synchronous. Unfortunately this was
inside a spinlock section in which we cannot sleep.
Modify the sending of the command back to async. This causes the mac80211
error "mac80211-phy0: failed to remove key (0, ff:ff:ff:ff:ff:ff) from
hardware (-16)." to return. This error is not serious since this occurs
during interface down and the keys will be cleared anyway when ucode is
unloaded. Having this error message is thus less serious than a potential
deadlock introduced when sleeping while holding a spinlock. We will have to
find another fix for that error.
This is a revert of the abovementioned commit.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the usbid for TP-Link TL-WN821N v2.
Cc: stable@kernel.org
Reported-by: Fabian Lenz <lenz_fabian@yahoo.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Autosleep needs to be disabled for AR9287 chipsets also.
Since autosleep is not used for any of the currently supported
chipsets, disable it by default and can be enabled if needed
for any of the future chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix bugs in programming registers during PA CAL"
removed a REG_READ of 0x7834. This resulted in incorrect
computation of the subsequent value to be written in RF2G6.
This patch fixes the regression by re-adding the REG_READ.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* This patch fixes a bug in calculating the scaled
power for three chain chipsets.
* Also, a delay is needed after setting DAC low-power mode in
TOP1 RF register (Top Level Register Bits).
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Do an AHB reset before doing RTC reset"
fixed RTC reset issue for AR9280 2.0 chipsets and above.
The fix is valid for all AR9280 chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to account for the number of chains in use,
not just the number of chains present.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9280 requires a full reset during channel change and HW reset.
Currently, a fast channel change is done. This patch fixes
this bug.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NF value may be incorrect when we read it just after the chip
has gone through a full sleep mode. Reading incorrect NF values
affects RX throughput.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting bit 20 and 25 of 0x8344 can cause occasional rx data
corruption, clear them to fix this issue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Waking up the chip after powering it down fails sometimes.
In this case the CPU is locked for 200ms. Reduce this
interval to 10ms to avoid excessive busy looping.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For chips requiring RTC reset, TSF has to be restored
after power on reset.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Disable L1 state ONLY when device is in D3 mode.
* Clear bit 22 of register 0x4004.
* Handle power on/off properly
Not setting the workarounds properly resulted in the
disappearance of the card in certain cases.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default noise floor was never initialized for
AR9287.This patch helps in reporting the correct
RSSI for this version of chipset.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LP (and probably N) PHY has the same radio disabled bit as
the higher-revision A and G PHYs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO works (more or less), so remove the BROKEN dependency and
let people test it.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the following build error when CONFIG_B43_LEDS is not selected:
drivers/net/wireless/b43/main.c: In function 'b43_remove':
drivers/net/wireless/b43/main.c:4990: error: 'struct b43_leds' has no member named 'stop'
drivers/net/wireless/b43/main.c:4991: error: 'struct b43_leds' has no member named 'work'
make[4]: *** [drivers/net/wireless/b43/main.o] Error 1
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't abuse wl->current_dev in the LED work for checking whether we're
going down. Add an explicit variable.
This fixes a crash on rmmod dereferencing the wl->current_dev NULL pointer
in various other places of the driver.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current verison of b43 uses "b43_phyop_switch_analog_generic" for A,
G and LP phys.
According to the spec, this is the wrong behaviour for the LP PHY
(see: http://bcm-v4.sipsolutions.net/802.11/PHY/Anacore )
While no problems on the x86 plattform where seen, this leads to a crash
on the BCM5354 SoC (MIPS 32 LE plattform).
This patch implements the analog switch for LP PHYs according to the
specs. It fixes the crash
signed-off-by: Thomas Ilnseher <illth@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reduces IRQ pressure by about one third on a saturated link
by disabling the PMQ mechanism. We currently don't use that mechanism.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for verbose runtime statistics.
It defaults to off and must be enabled in debugfs, if desired.
The first measurement may be incorrect, because statistics are not cleared
after they got enabled through debugfs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
synchronize_irq is meaningless for SDIO. sdio_release_irq will
sync the IRQ thread for us.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to release the SDIO host before locking the driver mutex.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for Soft-MAC SDIO devices to b43.
The driver still lacks some fixes for SDIO devices, so it's currently
marked as BROKEN.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes most of the b43 suspend/resume code (it's handled by mac80211)
and moves the registration of devices to the attachment phase. This is
required, because we must not register/unregister devices on suspend/resume.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a new usbid for Zcomax XG-705A to the device table.
Cc: stable@kernel.org
Reported-by: Jari Jaakola <jari.jaakola@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a bug in 4965 powersave that appears to
be related to the way it keeps track of its data
during sleep, but we haven't found it yet. Due to
that, using powersave may spontaneously cause the
device to SYSASSERT when transitioning from sleep
to wake. Therefore, disable powersave for 4965,
until (if ever, unfortunately) we can identify
and fix the problem.
Cf. http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1982
which was closed, but now has re-appeared with
IDLE mode, which probably means we never really
fixed it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can not assume antenna "A" is the first valid anttena for
all the NIC. Need to make sure choice the correct antenna based on
h/w configuration for transmit to avoid sending frame on invalid
antenna
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX handling maintains a few lists that keep track of the RX buffers.
Buffers move from one list to the other as they are used, replenished, and
again made available for usage. In one such instance, when a buffer is used
it enters the "rx_used" list. When buffers are replenished an skb is
attached to the buffer and it is moved to the "rx_free" list. The problem
here is that the buffer is first removed from the "rx_used" list _before_ the
skb is allocated. Thus, if the skb allocation fails this buffer remains
removed from the "rx_used" list and is thus lost for future usage.
Fix this by first allocating the skb before trying to attach it to a list.
We add an additional check to not do this unnecessarily.
Reported-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we cleaned up the driver to properly tell mac80211 about HT rates
("iwlwifi: use iwl_hwrate_get_mac80211_idx where appropriate"), we broke
internal rate indexing in 2.4 GHz band.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Tested-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a resume failure where a signal is pending on resume
so the firmware upload fails.
This removes the interruptible sleep, because we don't really need it.
In the worst case (with broken firmware) the sleep loop will take 1 second.
In the common case (working firmware), it will only take a few milliseconds.
So we don't really need to be interruptible.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this was added no defaults were set and it seems
this implies n. Default this to y.
Reported-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force wake the mac80211 queues on init.
Under rare circumstances they may be stopped, if a DMA error or
something else causes a device reset while a queue was stopped.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the hostap driver was converted to use net_device_ops, a mistake was
made in hostap_main.c (commit 5ae4efbcd2).
Originally, the tx_queue_len was set to 0 for every other interface than
HOSTAP_INTERFACE_MASTER, but the new fragment of code sets tx_queue_len to
0 only for HOSTAP_INTERFACE_MASTER. The opposite of the previous
behavior makes the driver to drop all packets in AP mode.
Change the way 0 is assigned to tx_queue_len according to the original
logic.
Signed-off-by: Martin Decky <martin@decky.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Originally, walk_memory_resource() was introduced to traverse all memory
of "System RAM" for detecting memory hotplug/unplug range. For doing so,
flags of IORESOUCE_MEM|IORESOURCE_BUSY was used and this was enough for
memory hotplug.
But for using other purpose, /proc/kcore, this may includes some firmware
area marked as IORESOURCE_BUSY | IORESOUCE_MEM. This patch makes the
check strict to find out busy "System RAM".
Note: PPC64 keeps their own walk_memory_resouce(), which walk through
ppc64's lmb informaton. Because old kclist_add() is called per lmb, this
patch makes no difference in behavior, finally.
And this patch removes CONFIG_MEMORY_HOTPLUG check from this function.
Because pfn_valid() just show "there is memmap or not* and cannot be used
for "there is physical memory or not", this function is useful in generic
to scan physical memory range.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Américo Wang <xiyou.wangcong@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc permitting variable length arrays makes the current construct used for
BUILD_BUG_ON() useless, as that doesn't produce any diagnostic if the
controlling expression isn't really constant. Instead, this patch makes
it so that a bit field gets used here. Consequently, those uses where the
condition isn't really constant now also need fixing.
Note that in the gfp.h, kmemcheck.h, and virtio_config.h cases
MAYBE_BUILD_BUG_ON() really just serves documentation purposes - even if
the expression is compile time constant (__builtin_constant_p() yields
true), the array is still deemed of variable length by gcc, and hence the
whole expression doesn't have the intended effect.
[akpm@linux-foundation.org: make arch/sparc/include/asm/vio.h compile]
[akpm@linux-foundation.org: more nonsensical assertions in tpm.c..]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Mimi Zohar <zohar@us.ibm.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an alternate solution to the EEM 'sentinel' CRC valiation issue.
CDC EEM allows using a 'sentinel' ethernet frame CRC of 0xdeadbeef in
place of a real CRC. The 'sentinel' value is transmitted in big-endian
order whereas the normal CRC is little-endian. This patch handles both
cases appropriately.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Virtio IDs are spread all over the tree which makes assigning new IDs
bothersome. Putting them together should make the process less error-prone.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This API change means that virtio_net can tell how much capacity
remains for buffers. It's necessarily fuzzy, since
VIRTIO_RING_F_INDIRECT_DESC means we can fit any number of descriptors
in one, *if* we can kmalloc.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dinesh Subhraveti <dineshs@us.ibm.com>
The iSCSI ring should be shutdown during uio_close instead of uio_open
for proper operations. This fixes the problem of the ring getting
stuck intermittently.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the driver for the SoC CAN controller in Atmel's
AT91SAM9263.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usbnet framework assumes USB hardware doesn't handle zero length
packets, but SMSC LAN95xx requires these to be sent for correct
operation.
This patch fixes an easily reproducible tx lockup when sending a frame
that results in exactly 512 bytes in a USB transmission (e.g. a UDP
frame with 458 data bytes, due to IP headers and our USB headers). It
adds an extra flag to usbnet for the hardware driver to indicate that
it can handle and requires the zero length packets.
This patch should not affect other usbnet users, please also consider
for -stable.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2b980dbd77
("lsm: Add hooks to the TUN driver") tun_set_iff doesn't
return -EINVAL though neither IFF_TUN nor IFF_TAP is set.
Signed-off-by: Kusanagi Kouichi <slash@ma.neweb.ne.jp>
Reviewed-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was introduced by b93d58 "8139*: convert printk() to pr_<foo>()":
[ 2256252443 ] <6>8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
The "version" string is printed using pr_info(), so it doesn't need to
include a loglevel.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
CC: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SKY2_HW_RAM_BUFFER bit in hw->flags was checked in sky2_mac_init(),
before being set later in sky2_up().
Setting SKY2_HW_RAM_BUFFER in sky2_init() where other hw->flags are set
should avoid this problem recurring.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set wol_ctrl_data to value 0, to remove compiling warning.
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definitions of vnet_ops and ehea_netdev_ops have initializations of a
local function and eth_change_mtu for their respective ndo_change_mtu
fields. This change uses only the local function.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@
if int(ps[0].line)!=int(pr[0].line) or int(ps[0].column)!=int(pr[0].column):
cocci.print_main(fld,p0)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
kaweth_control() never frees the buffer that it allocates for the USB
control message. Test case:
while :; do ifconfig eth2 down ; ifconfig eth2 up ; done
This is a tiny buffer so it is a slow leak. If you want to speed up the
process, you can change the allocation size to e.g. 16384 bytes, and it
will consume several megabytes within a few minutes.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
You can't ping the board or connect to it unless you send
any packet out from board.
Tested-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
After successful firmware init, return instead of
falling to error path (leading to detach) after
resuming to D0 state. This was broken in recent
firmware reset rehaul.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix minor bug in netdev tx timeout handling which could
always lead to firmware reset instead of pci function reset.
netxen_nic_reset_context() requires __NX_RESETTING bit
cleared.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'if (i < NR_INFO)' will only true if we breaks from 'for (i = 0; i < NR_INFO; i++)'
So removing useless 'if (i < NR_INFO)'
This also fixed following compilation warning :
CC [M] drivers/net/pcmcia/pcnet_cs.o
drivers/net/pcmcia/pcnet_cs.c: In function ‘get_hwinfo’:
drivers/net/pcmcia/pcnet_cs.c:321: warning: ‘base’ may be used uninitialized in this function
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a warning seen when doing namespace checking via
"make namespacecheck"
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shorten ixgbe_configure_rx() and lessen indent depth.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to set Tx specific itr values. This only makes sense
when there are separate vectors for Tx and Rx. When the queues are
doubled up RxTx on the vectors, we still only use the rx itr value.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We weren't stoping the sfp_timer after the device was brought down.
This patch properly cleans up.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for one channel CAN/USB interace CPC-USB/ARM7 from
EMS Dr. Thomas Wuensche (http://www.ems-wuensche.com).
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the removal of BUS_ID_SIZE, cpmac was not fully
converted to use MII_BUS_ID_SIZE as it ought to. This
patch fixes the following cpmac build failure:
CC drivers/net/cpmac.o
drivers/net/cpmac.c: In function 'cpmac_start_xmit':
drivers/net/cpmac.c:563: warning: comparison of distinct pointer types lacks a cast
drivers/net/cpmac.c: In function 'cpmac_probe':
drivers/net/cpmac.c:1112: error: 'BUS_ID_SIZE' undeclared (first use in this function)
drivers/net/cpmac.c:1112: error: (Each undeclared identifier is reported only once
drivers/net/cpmac.c:1112: error: for each function it appears in.)
Reported-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network layer now has a destructor we can hook to clean up the slip
devices array. That needs us to initiate unregister events in the right
places which with the current tty layer we can do, and with network
refcounting is safe to do.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
be2net: fix some cmds to use mccq instead of mbox
atl1e: fix 2.6.31-git4 -- ATL1E 0000:03:00.0: DMA-API: device driver frees DMA
pkt_sched: Fix qstats.qlen updating in dump_stats
ipv6: Log the affected address when DAD failure occurs
wl12xx: Fix print_mac() conversion.
af_iucv: fix race when queueing skbs on the backlog queue
af_iucv: do not call iucv_sock_kill() twice
af_iucv: handle non-accepted sockets after resuming from suspend
af_iucv: fix race in __iucv_sock_wait()
iucv: use correct output register in iucv_query_maxconn()
iucv: fix iucv_buffer_cpumask check when calling IUCV functions
iucv: suspend/resume error msg for left over pathes
wl12xx: switch to %pM to print the mac address
b44: the poll handler b44_poll must not enable IRQ unconditionally
ipv6: Ignore route option with ROUTER_PREF_INVALID
bonding: make ab_arp select active slaves as other modes
cfg80211: fix SME connect
rc80211_minstrel: fix contention window calculation
ssb/sdio: fix printk format warnings
p54usb: add Zcomax XG-705A usbid
...
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All cmds issued to BE after the creation of mccq must now use the mcc-q
(and not mbox) to avoid a hw issue that results in mbox poll timeout.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the wrong API when free dma. So when map dma use a flag to
demostrate whether it is 'pci_map_single' or 'pci_map_page'. When free
the dma, check the flags to select the right APIs('pci_unmap_single'
or 'pci_unmap_page').
set the flags type to u16 instead of unsigned long on David's comments.
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (53 commits)
m68knommu: Make PAGE_SIZE available to assembly files.
m68knommu: fix ColdFire definition of CLOCK_TICK_RATE
m68knommu: set multi-function pins for ethernet when enabled
m68knommu: remove special interrupt handling code for ne2k support
m68knommu: relax IO_SPACE_LIMIT setting
m68knommu: remove ColdFire direct interrupt register access
m68knommu: create a speciailized ColdFire 5272 interrupt controller
m68knommu: add support for second interrupt controller of ColdFire 5249
m68knommu: clean up old ColdFire timer irq setup
m68knommu: map ColdFire interrupts to correct masking bits
m68knommu: clean up ColdFire 532x CPU timer setup
m68knommu: simplify ColdFire "timers" clock initialization
m68knommu: support code to mask external interrupts on old ColdFire CPU's
m68knommu: merge old ColdFire interrupt controller masking macros
m68knommu: remove duplicate ColdFire mcf_autovector() code
m68knommu: move ColdFire INTC definitions to new include file
m68knommu: mask off all interrupts in ColdFire intc-simr controller
m68knommu: remove timer device interrupt setup for ColdFire 532x
m68knommu: remove interrupt masking from ColdFire pit timer
m68knommu: remove unecessary interrupt level setting in ColdFire 520x setup
...
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/netpoll.c::netpoll_send_skb() calls the poll handler when
it is available. As netconsole can be used from almost any context,
IRQ must not be enabled blindly in the NAPI handler of the driver
which supports netpoll.
Call trace:
netpoll_send_skb()
{
local_irq_save(flags)
-> netpoll_poll()
-> poll_napi()
-> poll_one_napi()
-> napi->poll()
-> b44_poll()
local_irq_restore(flags)
}
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I was implementing primary_passive option (formely named primary_lazy) I've
run into troubles with ab_arp. This is the only mode which is not using
bond_select_active_slave() function to select active slave and instead it
selects it itself. This seems to be not the right behaviour and it would be
better to do it in bond_select_active_slave() for all cases. This patch makes
this happen. Please review.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new usbid for Zcomax XG-705A to the device table.
Cc: stable@kernel.org
Reported-by: Jari Jaakola <jari.jaakola@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Driver Core: devtmpfs - kernel-maintained tmpfs-based /dev
debugfs: Modify default debugfs directory for debugging pktcdvd.
debugfs: Modified default dir of debugfs for debugging UHCI.
debugfs: Change debugfs directory of IWMC3200
debugfs: Change debuhgfs directory of trace-events-sample.h
debugfs: Fix mount directory of debugfs by default in events.txt
hpilo: add poll f_op
hpilo: add interrupt handler
hpilo: staging for interrupt handling
driver core: platform_device_add_data(): use kmemdup()
Driver core: Add support for compatibility classes
uio: add generic driver for PCI 2.3 devices
driver-core: move dma-coherent.c from kernel to driver/base
mem_class: fix bug
mem_class: use minor as index instead of searching the array
driver model: constify attribute groups
UIO: remove 'default n' from Kconfig
Driver core: Add accessor for device platform data
Driver core: move dev_get/set_drvdata to drivers/base/dd.c
Driver core: add new device to bus's list before probing
catas_reset() uses pointer to mlx4_priv, but mlx4_priv is not valid
after call mlx4_restart_one().
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the ColdFire 5272 has full interrupt controller functionality
we can remove all the interrupt masking and acking code from the FEC
ethernet driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Change default debugfs directory that mount for debugging
IWMC3200(Intel Wireless Multicomm 3200 WiFi driver).
As we all know, We need change default directory for consistency of
debugfs by Greg.K.H
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to problems at cam.org, my nico@cam.org email address is no longer
valid. FRom now on, nico@fluxnic.net should be used instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sorry Mike, I sent you off the wrong way. The following is simpler and the
second port is diffrent enough in setup (because of NAPI), that the
following is simpler.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be more accurate about number of transmit list elements required.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs,serial_cs:
add cis of Linksys lan&modem mulitifunction pcmcia card
and some modem card(MT5634ZLX, RS-COM-2P).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes commit e36b9d16c6. The approach
there is to call dev_close()/dev_open() whenever the device type is changed in
order to remap the device IP multicast addresses to HW multicast addresses.
This approach suffers from 2 drawbacks:
*. It assumes tha the device is UP when calling dev_close(), or otherwise
dev_close() has no affect. It is worth to mention that initscripts (Redhat)
and sysconfig (Suse) doesn't act the same in this matter.
*. dev_close() has other side affects, like deleting entries from the routing
table, which might be unnecessary.
The fix here is to directly remap the IP multicast addresses to HW multicast
addresses for a bonding device that changes its type, and nothing else.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using nanosleep() in an userspace application we get a ratelimit warning
NOHZ: local_softirq_pending 08
for 10 times.
The echo of CAN frames is done from process context and softirq context only.
Therefore the usage of netif_rx() was wrong (for years).
This patch replaces netif_rx() with netif_rx_ni() which has to be used from
process/softirq context. It also adds a missing comment that can_send() must
no be used from hardirq context.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
[ARM] Update mach-types
ARM: 5636/1: Move vendor enum to AMBA include
ARM: Fix pfn_valid() for sparse memory
[ARM] orion5x: Add LaCie NAS 2Big Network support
[ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
ARM: 5689/1: Update default config of HP Jornada 700-series machines
ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
ARM: 5688/1: ks8695_serial: disable_irq() lockup
ARM: 5687/1: fix an oops with highmem
ARM: 5684/1: Add nuc960 platform to w90x900
ARM: 5683/1: Add nuc950 platform to w90x900
ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
MMC: MMCI: convert realview MMC to use gpiolib
ARM: 5685/1: Make MMCI driver compile without gpiolib
ARM: implement highpte
ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
...
Fix up trivial conflict in arch/arm/kernel/signal.c.
It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
In the case of fiber and serdes adapters we were seeing issues with ethtool
-t causing kernel panics due to null function pointers. To prevent this we
need to exit out of the phy reset code in the event that we do not have a
valid phy.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our SGMII phy code was incomplete in that it was not actually placing the
phy in SGMII mode and as a result the PHY was not able to establish a link
when connected to a non serdes link partner. This patch updates the code
to combine the SGMII/serdes PCS init and to add the necessary reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the media type detection for CX4 adapters lumps them into a
type of fiber. This causes some strange fallout when firmware verification
is done on the NIC, and certain fiber NIC rules get enforced incorrectly.
This patch introduces a new media type for CX4, and puts both 82598 and
82599 CX4 adapters into this bucket.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for CX4 adapters based on 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet split feature was recently moved out of the adapter-wide flags
feature field and into a per-Rx ring feature field. In the process, packet
split isn't properly disabled in the Rx ring if the adapter has it globally
disabled, followed by a device reset.
This won't impact the driver today, since it's always in packet split mode.
However, this will prevent any pitfalls if someone disables packet split on
the adapter in the future and doesn't disable it in each ring.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all Blackfin boards are using the board resources, we don't need
to keep the arch/board specific crap in the driver header.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bug in 4965 powersave that appears to
be related to the way it keeps track of its data
during sleep, but we haven't found it yet. Due to
that, using powersave may spontaneously cause the
device to SYSASSERT when transitioning from sleep
to wake. Therefore, disable powersave for 4965,
until (if ever, unfortunately) we can identify
and fix the problem.
Cf. http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1982
which was closed, but now has re-appeared with
IDLE mode, which probably means we never really
fixed it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can not assume antenna "A" is the first valid anttena for
all the NIC. Need to make sure choice the correct antenna based on
h/w configuration for transmit to avoid sending frame on invalid
antenna
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX handling maintains a few lists that keep track of the RX buffers.
Buffers move from one list to the other as they are used, replenished, and
again made available for usage. In one such instance, when a buffer is used
it enters the "rx_used" list. When buffers are replenished an skb is
attached to the buffer and it is moved to the "rx_free" list. The problem
here is that the buffer is first removed from the "rx_used" list _before_ the
skb is allocated. Thus, if the skb allocation fails this buffer remains
removed from the "rx_used" list and is thus lost for future usage.
Fix this by first allocating the skb before trying to attach it to a list.
We add an additional check to not do this unnecessarily.
Reported-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we cleaned up the driver to properly tell mac80211 about HT rates
("iwlwifi: use iwl_hwrate_get_mac80211_idx where appropriate"), we broke
internal rate indexing in 2.4 GHz band.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Tested-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a resume failure where a signal is pending on resume
so the firmware upload fails.
This removes the interruptible sleep, because we don't really need it.
In the worst case (with broken firmware) the sleep loop will take 1 second.
In the common case (working firmware), it will only take a few milliseconds.
So we don't really need to be interruptible.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this was added no defaults were set and it seems
this implies n. Default this to y.
Reported-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force wake the mac80211 queues on init.
Under rare circumstances they may be stopped, if a DMA error or
something else causes a device reset while a queue was stopped.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the hostap driver was converted to use net_device_ops, a mistake was
made in hostap_main.c (commit 5ae4efbcd2).
Originally, the tx_queue_len was set to 0 for every other interface than
HOSTAP_INTERFACE_MASTER, but the new fragment of code sets tx_queue_len to
0 only for HOSTAP_INTERFACE_MASTER. The opposite of the previous
behavior makes the driver to drop all packets in AP mode.
Change the way 0 is assigned to tx_queue_len according to the original
logic.
Signed-off-by: Martin Decky <martin@decky.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
o Add QLogic copyright, add linux-driver@qlogic.com to
MAINTAINERS.
o Delete old contact information.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redesign tx timeout handling in line with new firmware
reset design that co-ordinates with other PCI function
drivers.
o For NX3031, first try to reset PCI function's own
context before requesting firmware reset.
o For NX2031, since firmware heartbit is not supported
directly request firmware reset.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release file firmware when no firmware reset is required.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Access on card memory through memory controller (agent)
rather than moving small pci window around. Clean up the
code for moving windows around.
o Restrict memory accesss to 64 bit, currently only firmware
download uses this.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 8 byte strides for firmware download into card
memory since oncard memory controller needs 8 byte
(64 bit) accesses. This avoids unnecessary rmw cycles.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f6eb9b1fc1, "tg3: Add 5717 asic
rev" changed how the rx return ring size operations are done. It
effectively inverts the sense of the previous test, but it failed to
also invert the resulting sizes. This patch corrects that error.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_INET is disabled, netxen has a build failure:
netxen_nic_main.c:(.text+0x118fd1): undefined reference to `netxen_config_indev_addr'
so make that function just an empty stub when CONFIG_INET=n.
(not "inline" since that conflicts with other declarations of it)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.
To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.
# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5
This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.
The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The txq_set_wrr() function in drivers/net/mv643xx_eth.c is
unused, not even referenced under #if 0 or something like that,
which results in a compile-time warning:
drivers/net/mv643xx_eth.c:1070: warning: 'txq_set_wrr' defined but not used
Fix: remove it.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC8360 QE UCC ethernet controllers hang when changing link duplex
under a load (a bit of NFS activity is enough).
PHY: mdio@e0102120:00 - Link is Up - 1000/Full
sh-3.00# ethtool -s eth0 speed 100 duplex half autoneg off
PHY: mdio@e0102120:00 - Link is Down
PHY: mdio@e0102120:00 - Link is Up - 100/Half
NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at c01fcbd0 [verbose debug info unavailable]
NIP: c01fcbd0 LR: c01fcbd0 CTR: c0194e44
...
The cure is to disable the controller before changing speed/duplex
and enable it afterwards.
Though, disabling the controller might take quite a while, so we
better not grab any spinlocks in adjust_link(). Instead, we quiesce
the driver's activity, and only then disable the controller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll need ugeth_disable() and ugeth_enable() calls earlier in the
file, so rearrange some code to avoid forward declarations.
The patch doesn't contain any functional changes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to specs, when auto-negotiation is disabled, Marvell PHYs need
a software reset after changing speed/duplex forcing bits. Otherwise,
the modified bits have no effect.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
And also do a better job of returning proper NET_{RX,XMIT}_ values.
Based on a patch and suggestions by Mark Smith.
This fixes CVE-2009-2903
Reported-by: Mark Smith <lk-netdev@lk-netdev.nosense.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (48 commits)
RDMA/iwcm: Reject the connection when the cm_id is destroyed
RDMA/cxgb3: Clean up properly on FW mismatch failures
RDMA/cxgb3: Don't ignore insert_handle() failures
MAINTAINERS: InfiniBand/RDMA mailing list transition to vger
IB/mad: Allow tuning of QP0 and QP1 sizes
IB/mad: Fix possible lock-lock-timer deadlock
RDMA/nes: Map MTU to IB_MTU_* and correctly report link state
RDMA/nes: Rework the disconn routine for terminate and flushing
RDMA/nes: Use the flush code to fill in cqe error
RDMA/nes: Make poll_cq return correct number of wqes during flush
RDMA/nes: Use flush mechanism to set status for wqe in error
RDMA/nes: Implement Terminate Packet
RDMA/nes: Add CQ error handling
RDMA/nes: Clean out CQ completions when QP is destroyed
RDMA/nes: Change memory allocation for cqp request to GFP_ATOMIC
RDMA/nes: Allocate work item for disconnect event handling
RDMA/nes: Update refcnt during disconnect
IB/mthca: Don't allow userspace open while recovering from catastrophic error
IB/mthca: Distinguish multiple devices in /proc/interrupts
IB/mthca: Annotate CQ locking
...
and convert PXA-based devices to gpio_pwdown where possible.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The macro res_size in drivers/net/dm9000.c is a copy of resource_size in
linux/ioport.h. Remove the function and use resource_size instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the offset of vlan_TCI field in cmd_desc_type0.
Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in checking dest ip has support before
programming destip addresses.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oops, a stupid mistake in the original patch which adds coex 3-wire
support. Bluetooth priority gpio needs to be gpio 7.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This subsystem id will be used later to turn on the btcoex
support.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The preferred module is p54pci which also supports FullMAC
PCI / Cardbus devices. We schedule removal for 2.6.34. Reason
to remove this is no one really is testing prism54 anymore,
and while it works p54pci provides support for the same hardware.
It should be noted I have been told some FullMAC devices may not
have worked with the SoftMAC driver but to date we have yet to
recieve a single bug report regarding this. If there are users
out there please let us know!
Cc: aquilaver@yahoo.com
Cc: linux-kernel@vger.kernel.org
Cc: Dan Williams <dcbw@redhat.com>
Cc: Kai Engert <kengert@redhat.com>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Tim de Waal<tim.dewaal@yahoo.com>
Cc: Roy Marples <uberlord@gentoo.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Christian Lamparter <chunkeey@web.de>
Cc: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some gcc warnings for switch statements.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a sparse warning in the hardware-TKIP code:
drivers/net/wireless/b43/xmit.c:272:18: warning: incorrect type in assignment (different base types)
drivers/net/wireless/b43/xmit.c:272:18: expected unsigned short [unsigned] [short] <noident>
drivers/net/wireless/b43/xmit.c:272:18: got restricted unsigned short [usertype] <noident>
The code should work correctly with and without this patch applied.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when QoS-disable is requested, we would leave QoS enabled
in firmware, but only queue frames on one queue.
Change that and also tell firmware about disabled QoS, so it
completely ignores all the QoS parameters. Also don't upload the parameters,
if QoS is disabled.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calculated values for the ACK timeout and ACK
consume time are different then the values as
used by the Legacy drivers.
After testing from James Ledwith it appeared that
the calculated values caused a high amount of TX
failures, and the values from the Legacy drivers
were the most optimal to prevent TX failure due to
excessive retries.
The symptoms of this problem:
- Rate control module always falls back to 1Mbs
- Low throughput when bitrate was fixed
Possible side-effects (not confirmed but highly likely)
- Problems with DHCP
- Broken connections due to lack of probe response
This should fix at least:
Kernel bugzilla reports: [13362], [13009], [9273]
Fedora bugzilla reports: [443203]
but possible some additional bugs as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function res_size in drivers/net/niu.c is a copy of resource_size in
linux/ioport.h. Remove the function and use resource_size instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCMCIA support works well and is not experimental anymore.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
apply the conformance test limits (CTL) stored in the eeprom upon
the values calculated for the tx power (ar->power_*).
This is based on the implementation in the vendor driver
(hal/hpmain.c, line 3700 ff.) with one difference:
If any ctl mode isn't found in the eeprom, we fall back to the "lower",
legacy modes (5GHT20,11A or 2GHT20,11G,11B). Otus only did 5GHT20->11A.
Currently CTL are applied for the FCC group only.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ar9170 driver needs the defines for conformance test limit groups
and cannot include regd_common.h
Signed-off-by: Joerg Albert <jal2@gmx.de>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the SHM spinlock.
SHM is protected by wl->mutex.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the PIO RX work. It's not needed anymore, because
we can sleep in the threaded interrupt handler.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the DMA/PIO queue locks. Locking is handled by
wl->mutex now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the TX spinlock and defers TX to a workqueue to allow
locking wl->mutex instead and to allow sleeping for register accesses.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a threaded IRQ handler to allow locking the mutex and
sleeping while executing an interrupt.
This removes usage of the irq_lock spinlock, but introduces
a new hardirq_lock, which is _only_ used for the PCI/SSB lowlevel
hard-irq handler. Sleeping busses (SDIO) will use mutex instead.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports some code from the vendor driver, which is
supposed to upload the right calibration values for the
chosen frequency.
In theory, this should give a better range and throughput
for all users with the open, or one-stage firmware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHANNEL_G has to be set for 2GHZ channels since
IS_CHAN_G() checks for this in channelFlags and not in
chanmode. To make things messier, ath9k_hw_process_ini()
checks for CHANNEL_G in chanmode and not in channelFlags.
The supreme, brain-searing fix is to set the
flag in both cases.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BAR frames have to be sent to mac80211 only if the
current channel is HT. Also, move the macro to
enum ath9k_rx_filter.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k ahb requests an IRQ and indicates 'ath9k' claimed it,
ath9k pci requests an IRQ and indicates 'ath' claims it;
since 'ath' is another module sync both ahb and pci to claim
the irq using 'ath9k'.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've cleaned up ath_init_device() and its children enough
to pass meaninful errors back from probe. When this fails
it means our device could not be initialized and a meaninful
error will have been passed.
Do the same for request_irq() and also synchronize the error
messages while at it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The -ENOMEM was never being passed on failure.
While at it use dev_err() as ahb does upon failure.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the initialisation of some PHY registers
from the modal_header[] values in the EEPROM
(see otus/hal/hpmain.c, line 333 ff.)
Signed-off-by: Joerg Albert <jal2@gmx.de>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported by Stephen Rothwell:
drivers/net/r8169.c: In function 'rtl8169_start_xmit':
drivers/net/r8169.c:3421: warning: label 'out' defined but not used
Introduced by commit 61357325f3 ("netdev:
convert bulk of drivers to netdev_tx_t").
Signed-off-by: David S. Miller <davem@davemloft.net>
m68k:
drivers/net/hydra.c:178: warning: format '%08lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HSS usually uses external clocks, so it's not a big deal. Internal clock
is used for direct DTE-DTE connections and when the DCE doesn't provide
it's own clock.
This also depends on the oscillator frequency. Intel seems to have
calculated the clock register settings for 33.33 MHz (66.66 MHz timer
base). Their settings seem quite suboptimal both in terms of average
frequency (60 ppm is unacceptable for G.703 applications, their primary
intended usage(?)) and jitter.
Many (most?) platforms use a 33.333 MHz oscillator, a 10 ppm difference
from Intel's base.
Instead of creating static tables, I've created a procedure to program
the HSS clock register. The register consists of 3 parts (A, B, C).
The average frequency (= bit rate) is:
66.66x MHz / (A + (B + 1) / (C + 1))
The procedure aims at the closest average frequency, possibly at the
cost of increased jitter. Nobody would be able to directly drive an
unbufferred transmitter with a HSS anyway, and the frequency error is
what it really counts.
I've verified the above with an oscilloscope on IXP425. It seems IXP46x
and possibly IXP43x use a bit different clock generation algorithm - it
looks like the avg frequency is:
(on IXP465) 66.66x MHz / (A + B / (C + 1)).
Also they use much greater precomputed A and B - on IXP425 it would
simply result in more jitter, but I don't know how does it work on
IXP46x (perhaps 3 least significant bits aren't used?).
Anyway it looks that they were aiming for exactly +60 ppm or -60 ppm,
while <1 ppm is typically possible (with a synchronized clock, of
course).
The attached patch makes it possible to set almost any bit rate
(my IXP425 533 MHz quits at > 22 Mb/s if a single port is used, and the
minimum is ca. 65 Kb/s).
This is independent of MVIP (multi-E1/T1 on one HSS) mode.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI200SYN has its own PCI subsystem device ID for 3+ years, now it's
time to remove the generic PLX905[02] ID from the driver. Anyone with
old EEPROM data will have to run the upgrade.
Having the generic PLX905[02] (PCI-local bus bridge) ID is harmful
as the driver tries to handle other devices based on these bridges.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code changes to
- In the tx completion processing, there were instances of unmapping a
memory as a page which was originally mapped as single. This patch takes care
of this by using skb_dma_map()/skb_dma_unmap() to map/unmap Tx buffers.
- set gso_max_size to 65535. This was not done till now.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to support flashing of the be2 network adapter using the
request_firmware() & ethtool infrastructure. The trigger to flash the device
will come from ethtool utility. The driver will invoke request_firmware()
to start the flash process. The file containing the flash image is expected
to be available in /lib/firmware/
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a brute force removal of the wierd slave interface done for
DLCI -> SDLA transmit. Before it was using non-standard return values
and freeing skb in caller. This changes it to using normal return
values, and freeing in the callee. Luckly only one driver pair was
doing this. Not tested on real hardware, in fact I wonder if this
driver pair is even being used by any users.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Combine netxen_get_firmware_info(), netxen_check_options()
so that they are updated every time firmware is reset.
o Set dma mask everytime firmware is reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For registers accessed in fast path (interrupt / softirq)
avoid expensive I/O address translation. These registers
are directly mapped in PCI bar 0 and do not require
any window checks.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reprogram local IP addresses after firmware is reset
or after resuming from suspend.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement state machine to detect firmware hung state
and recover. Since firmware will be shared by all PCI
functions that have different class drivers (NIC or
FCOE or iSCSI), explicit hardware based serialization
is required for initializing firmware.
o Used global scratchpad register to maintain device
reference count. Every probed pci function adds to
ref count.
o Implement timer (delayed work) for each pci func
that checks firmware heartbit every 5 sec and detaches
itself if firmware is dead. Last detaching function
reloads firmware. Other functions wait for firmware
init, and re-attach themselves.
Heartbit is not supported by NX2031 firmware.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unwind allocations and release file firmware when
when firmware load fails.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Michael Guntsche <mike@it-loops.com>
--------------------
Commit
38bddf04bc gianfar: gfar_remove needs to call unregister_netdev()
breaks the build of the gianfar driver because "dev" is undefined in
this function. To quickly test rc9 I changed this to priv->ndev but I do
not know if this is the correct one.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mlx4 driver uses the same name for interrupts for every
device in the system. This can make it very confusing trying to work
out exactly which device MSI-X interrupts are for. Change the driver
to add the PCI name of the device to the interrupt name.
Signed-off-by: Arputham Benjamin <abenjamin@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On the error path of mlx4_init_hca(), mlx4_close_hca() is called,
followed by mlx4_free_icms() and mlx4_UNMAP_FA(). But both those
functions are also called from mlx4_close_hca(), which leads to a
double free.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current implementation allocates a single host page for EQ context
memory, which was OK when we only allocated a few EQs. However, since
we now allocate an EQ for each CPU core, this patch removes the
hard-coded limit (which we exceed with 4 KB pages and 128 byte EQ
context entries with 32 CPUs) and uses the same ICM table code as all
other context tables, which ends up simplifying the code quite a bit
while fixing the problem.
This problem was actually hit in practice on a dual-socket Nehalem box
with 16 real hardware threads and sufficiently odd ACPI tables that it
shows on boot
SMP: Allowing 32 CPUs, 16 hotplug CPUs
so num_possible_cpus() ends up 32, and mlx4 ends up creating 33 MSI-X
interrupts and 33 EQs. This mlx4 bug means that mlx4 can't even
initialize at all on this quite mainstream system.
Cc: <stable@kernel.org>
Reported-by: Eli Cohen <eli@mellanox.co.il>
Tested-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The old code used two calls to pci_request_region() to get the two BARs
for the mlx4 device, for no particularly good reason. Clean up the code
a little by converting this to a single call to pci_request_regions().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Massage the err_handler upcall into an event handler upcall, pass
netdev port events to the cxgb3 ULPs and generate RDMA port events
based on LLD port events.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds support for legacy SJA1000 CAN controllers on the ISA
or PC-104 bus. The I/O port or memory address and the IRQ number must
be specified via module parameters:
insmod sja1000_isa.ko port=0x310,0x380 irq=7,11
for ISA devices using I/O ports or:
insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11
for memory mapped ISA devices.
Indirect access via address and data port is supported as well:
insmod sja1000_isa.ko port=0x310,0x380 indirect=1 irq=7,11
Here is a full list of the supported module parameters:
port:I/O port number (array of ulong)
mem:I/O memory address (array of ulong)
indirect:Indirect access via address and data port (array of byte)
irq:IRQ number (array of int)
clk:External oscillator clock frequency (default=16000000 [16 MHz])
(array of int)
cdr:Clock divider register (default=0x48 [CDR_CBP | CDR_CLK_OFF])
(array of byte)
ocr:Output clock register (default=0x18 [OCR_TX0_PUSHPULL])
(array of byte)
Note: for clk, cdr, ocr, the first argument re-defines the default
for all other devices, e.g.:
insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000
is equivalent to
insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11 \
clk=24000000,24000000
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The member "tx_bytes" of "struct net_device_stats" should be
incremented when the interrupt is done and an "arbitration
lost error" is a TX error and the statistics should be updated
accordingly.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the function can_free_echo_skb to the CAN
device interface to allow upcoming drivers to release echo
skb's in case of error.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Stephen Rothwell:
Today's linux-next build (x86_64 allmodconfig gcc-4.4.0)
produced this warning:
drivers/net/wan/dscc4.c: In function 'dscc4_rx_skb':
drivers/net/wan/dscc4.c:670: warning: suggest parentheses around comparison in operand of '|'
which actually points out a bug, I think. It is doing
(x & (y | z)) != y | z
when it probably means
(x & (y | z)) != (y | z)
Introduced by commit 5de3fcab91
("WAN: bit and/or confusion").
Signed-off-by: David S. Miller <davem@davemloft.net>
To unclutter probe() a little bit, put all device initialization code
in one spot and device deinit code in another spot. Also remove unused
rq->buf_index variable/func.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nic firmware can return zero for port MTU, so check for non-zero value
before checking for change in port MTU.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deprecate some old APIa; change arguments to stats dump all API; add new
interrupt assert API
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provision for multiple Rx/Tx queues. Max of 8 WQs and 8 RQs. Max for
completion queue is 8+8=16 and max for interrupt resources is 8+8+2.
Add driver/firmware interface for setting up RSS secret key and indirection
table.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: included MAC drops in rx_dropped netstat. Also track Rx trunctations
stat at the MAC
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some driver -> nic firmware calls weren't guarded with a spinlock, exposing
the call i/f to a race between two threads
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic WQ desc supports a maximum 16K buf size, so split any send fragments
larger than 16K into several descs.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A0 revision ASIC has an erratum on the RQ desc cache on chip where the
cache can become corrupted causing pkt buf writes to wrong locations. The s/w
workaround is to post a dummy RQ desc in the ring every 32 descs, causing a
flush of the cache. A0 parts are not production, but there are enough of
these parts in the wild in test setups to warrant including workaround. A1
revision ASIC parts fix erratum.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nic firmware can place resources (queues, intrs, etc) on multiple BARs, so
allow driver to discover/map resources beyond BAR0.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan devices are currently not multi-queue capable.
We can do that defining rtnl_link_ops method,
get_tx_queues(), called from rtnl_create_link()
This new method gets num_tx_queues/real_num_tx_queues
from lower device.
macvlan_get_tx_queues() is a copy of vlan_get_tx_queues().
Because macvlan_start_xmit() has to update netdev_queue
stats only (and not dev->stats), I chose to change
tx_errors/tx_aborted_errors accounting to tx_dropped,
since netdev_queue structure doesnt define tx_errors /
tx_aborted_errors.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few drivers still access the arguments to MDIO ioctls as an array of
u16. Convert them to use struct mii_ioctl_data.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard MDIO ioctl numbers are well-established and these should
no longer be needed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While perusing vendor driver, I saw that it did not enable the Vaux
power unless device was able to wake from lan for D3cold.
This might help for Rene's power issue.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a perpetual while() loop in unwinding partial
mapped tx skb on dma mapping failure.
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate calls to netxen_napi_add().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alloc 12k skbuffs so that firmware can aggregate more
packets into one buffer. This doesn't raise memory
consumption since 9k skbs use 16k slab cache anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FCoE DDP in 82599 can be used for both FCoE initiator as well as FCoE
target, depending on the indication of the exchange being the responder or
originator in the F_CTL (frame control) field in the encapsulated Fiber
Channel frame header (T10 Spec., FC-FS). For the initiator, OX_ID is used
for FCoE DDP, where for the target RX_ID is used for FCoE DDP.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a simple selection of a FCoE tx queue based on the current cpu id to
distribute transmission of FCoE traffic evenly among multiple FCoE transmit
queues.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for multiple transmit queues to the Fiber Channel
over Ethernet (FCoE) feature found in 82599. Currently, FCoE has multiple
Rx queues available, along with a redirection table, that helps distribute
the I/O load across multiple CPUs based on the FC exchange ID. To make
this the most effective, we need to provide the same layout of transmit
queues to match receive.
Particularly, when Data Center Bridging (DCB) is enabled, the designated
traffic class for FCoE can have dedicated queues for just FCoE traffic,
while not affecting any other type of traffic flow.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates things so that vlan tags are taken into account when
setting the receive large packet maximum length. This allows the VF driver
to correctly receive full sized frames when vlans are enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb_irq_disable/enable calls were causing virtual functions associated
with the igb physical function to have their interrupts disabled. In order
to prevent this from occuring we should only clear/set the bits related to
the physical function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the set_rx_mode netdevice operation so that igb
can better support multiple unicast addresses.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_mii, fec_enet_rx and fec_enet_tx are both only called by
fec_enet_interrupt in interrupt context. So they must not use
spin_lock_irq/spin_unlock_irq.
This fixes:
WARNING: at kernel/lockdep.c:2140 trace_hardirqs_on_caller+0x130/0x194()
...
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_discover_phy is only called by fec_enet_mii (via mip->mii_func). So
&fep->mii_lock is already held and mii_discover_phy must not call
mii_queue which locks &fep->mii_lock, too.
This was noticed by lockdep:
=============================================
[ INFO: possible recursive locking detected ]
2.6.31-rc8-00038-g37d0892 #109
---------------------------------------------
swapper/1 is trying to acquire lock:
(&fep->mii_lock){-.....}, at: [<c01569f8>] mii_queue+0x2c/0xcc
but task is already holding lock:
(&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460
other info that might help us debug this:
2 locks held by swapper/1:
#0: (rtnl_mutex){+.+.+.}, at: [<c0183534>] rtnl_lock+0x18/0x20
#1: (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460
stack backtrace:
Backtrace:
[<c00226fc>] (dump_backtrace+0x0/0x108) from [<c01eac14>] (dump_stack+0x18/0x1c)
r6:c781d118 r5:c03e41d8 r4:00000001
[<c01eabfc>] (dump_stack+0x0/0x1c) from [<c005bae4>] (__lock_acquire+0x1a20/0x1a88)
[<c005a0c4>] (__lock_acquire+0x0/0x1a88) from [<c005bbac>] (lock_acquire+0x60/0x74)
[<c005bb4c>] (lock_acquire+0x0/0x74) from [<c01edda8>] (_spin_lock_irqsave+0x54/0x68)
r7:60000093 r6:c01569f8 r5:c785e468 r4:00000000
[<c01edd54>] (_spin_lock_irqsave+0x0/0x68) from [<c01569f8>] (mii_queue+0x2c/0xcc)
r7:c785e468 r6:c0156b24 r5:600a0000 r4:c785e000
[<c01569cc>] (mii_queue+0x0/0xcc) from [<c0156b78>] (mii_discover_phy+0x54/0xa8)
r8:00000002 r7:00000032 r6:c785e000 r5:c785e360 r4:c785e000
[<c0156b24>] (mii_discover_phy+0x0/0xa8) from [<c0156354>] (fec_enet_interrupt+0xa4/0x460)
r5:c785e360 r4:c077a170
[<c01562b0>] (fec_enet_interrupt+0x0/0x460) from [<c0066674>] (handle_IRQ_event+0x48/0x120)
[<c006662c>] (handle_IRQ_event+0x0/0x120) from [<c0068438>] (handle_level_irq+0x94/0x11c)
...
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpq ether driver is modifying the data art of the skb by first
dropping the KISS byte (a command byte for the radio) then prepending the
length + 4 of the remaining AX.25 packet to be transmitted as a little
endian 16-bit number. If the high byte of the length has a different
value than the dropped KISS byte users of clones of the skb may observe
this as corruption. This was observed with by running listen(8) -a which
uses a packet socket which clones transmit packets. The corruption will
then typically be displayed for as a KISS "TX Delay" command for AX.25
packets in the range of 252..508 bytes or any other KISS command for
yet larger packets.
Fixed by using skb_cow to create a private copy should the skb be cloned.
Using skb_cow also allows us to cleanup the old logic to ensure sufficient
headroom in the skb.
While at it, replace a return of 0 from bpq_xmit with the proper constant
NETDEV_TX_OK which is now being used everywhere else in this function.
Affected: all 2.2, 2.4 and 2.6 kernels.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Jann Traschewski <jann@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Request_irq() may fail in different ways, handle accordingly.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change it to a menuconfig to give it some documentation, to
refer users to our wireless wiki for extra resources and
documentation. It seems our wiki is still obscure to some.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.102.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 is a dual port chip that has a shared MDIO bus design. While
it is impossible for one function to interface with the wrong phy, that
function still needs to know which MDIO bus address to use when
interfacing with its own phy. This patch adds code to determine which
MDIO bus address to use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds NVRAM detection routines for the 5717.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5717 asic rev.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RSS is enabled, the status block format changes slightly. The
"rx_jumbo_consumer", "reserved", and "rx_mini_consumer" members get
mapped to the other three rx return ring producer indexes. This patch
introduces a new per-interrupt member which identifies which location
in the status block a particular vector should look for return ring
updates.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multivector RSS is enabled, the first interrupt vector is only used
to report link interrupts and error conditions. This patch changes the
code so that rx and tx ring resources are not allocated for this vector.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code needed to enable RSS.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to tune the coalescing parameters for the other
msix vectors.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to enable and disable the rest of the NAPI
instances.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exposes the additional transmit rings to the kernel and makes
the necessary modifications to transmit, open, and close paths.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes up two spots that need attention now that msix support
has been added.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to assign status block, tx producer ring and rx
return ring resources needed for the other interrupt vectors.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 assigns mailbox locations to interrupt vectors in a rather
non-intuitive way. (Much of the complexity stems from legacy
compatibility issues.) This patch implements the assignment scheme.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds MSI-X support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to support multiple interrupt vectors around the
kernel's interrupt API.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves most of the chip ring setup logic into a separate
function. This will make it easier to verify the multi ring setup
changes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each interrupt vector has its own bit in the host coalescing register to
force that vector's status block to be updated and generate an
interrupt. This patch adds a member to the per-interrupt structure
that records which bit belongs to that vector.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch inlines the code of tg3_cond_int() into the function's only
callsite. This prep work makes the following patch cleaner.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aup->mii_bus->irq allocation may fail, prevent a dereference of NULL.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
B0_CTST is a 24bit register according to the vendor driver (sk98lin).
A 16bit read on B0_CTST will always return 0 for Y2_VAUX_AVAIL (1<<16),
so use a 32bit read when testing Y2_VAUX_AVAIL
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor similar two sections of code that free buffers into one.
Only call tx_init if all buffer allocations succeed.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Observed by Mike McCormack.
The LED bit here is just a software controlled value used to
turn on one of the LED's on some boards. The register value was wrong,
which could have been causing some power control issues.
Get rid of problematic define use the correct mask.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As tun always has an embeedded struct sock,
use sk and sk_receive_queue fields instead of
duplicating them in tun_struct.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can speedup ether addresses compares using compare_ether_addr_64bits()
instead of memcmp(). We make sure all operands are at least 8 bytes long and
16bits aligned (or better, long word aligned if possible)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To speedup ether addresses compares, we can use compare_ether_addr_64bits()
(all operands are guaranteed to be at least 8 bytes long)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 82599 multi speed fiber case when driver is loaded without any
cable and reconnecting the cable with a 1G partner does not bring
up the link in 1Gb mode. When there is no link we first setup the link
at 10G & 1G and then try to re-establish the link at highest speed 10G
and thereby changing autoneg_advertised value to highest speed 10G.
After connecting back the cable to a 1G link partner we never try 1G
as autoneg advertised value is changed to link at 10G only. The
following patch fixes the issue by properly initializing the
autoneg_advertised value just before exiting from link setup routine.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling the Rx and Tx data arbiters prior to configuration changes,
the arbiters were not being shut down properly. This can create a race
in the DCB hardware blocks, and potentially hang the arbiters. Also, the
Tx descriptor arbiter shouldn't be disabled when applying configuration
changes; disabling this arbiter can cause a Tx hang.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link code cleanup: a number of redundant functions and MAC variables are cleaned up,
with some functions being consolidated into a single-purpose code path.
Removed following deprecated link functions and mac variables
* ixgbe_setup_copper_link_speed_82598
* ixgbe_setup_mac_link_speed_multispeed_fiber
* ixgbe_setup_mac_link_speed_82599
* mac.autoneg, mac.autoneg_succeeded, phy.autoneg_wait_to_complete
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling VLAN filters (VFE) when the primary interface is brought up
(per commit 78ed11a) has caused problems for some users who manage
their systems using IPMI over a VLAN. This is because when the driver
enables the VLAN filter, this same filter table is enabled for the
management channel, and the table is initially empty, which means that
the IPMI/VLAN packets are filtered out and not received by the BMC.
This is a problem only on e1000 class adapters, as it is only
on e1000 that the filter table is common to the management and host
streams.
With this change, filtering is only enabled when one or more host VLANs
exist, and is disabled when the last host VLAN is removed. VLAN filtering
is always disabled when the primary interface is in promiscuous mode,
and will be (re)enabled if VLANs exist when the interface exits
promiscuous mode.
Note that this does not completely resolve the issue for those using VLAN
management, because if the host adds a VLAN, then the above problem
occurs when that VLAN is enabled. However, it does mean the there is no
problem for configurations where management is on a VLAN and the host is
not.
A complete solution to this issue would require further driver changes.
The driver would need to discover if (and which) management VLANs are
active before enabling VLAN filtering, so that it could ensure that the
managed VLANs are included in the VLAN filter table. This discovery
requires that the BMC identifies its VLAN in registers accessible
to the driver, and at least on Dell PE2850 systems the BMC does not
identify its VLAN to allow such discovery. Intel is pursuing this issue
with the BMC vendor.
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to check what was the last fw error we got accross resets, we add
this debugfs entry. It displays the complete ASSERT information.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When UMAC stalls or asserts, we want to reset the device. But when we're
associated, the current reset worker will end up calling
cfg80211_connect_result() with the cfg80211 sme layer knowing that we're
reassociating. That ends up with some ugly warnings.
With this patch we're telling the upper layer that we've roamed if
reassociation succeeds, and that we're disconnected if it fails.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LMAC calibration API got broken mostly by having a configuration bitmap
being different than the result one.
This patch tries to address that issue by correctly running calibrations with
the newest firmwares, and keeping a backward compatibility fallback path for
older firmwares, where the configuration and result bitmaps were identical.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also mark some functions static.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver receives "connection terminated" event from device,
it could be caused by 2 reasons: the firmware is roaming or the
connection is lost (AP disappears). For the former, an association
complete event is supposed to come within 3 seconds. For the latter,
the driver won't receive any event except the connection terminated.
So we kick a delayed work (5*HZ) when we receive the connection
terminated event. It will be canceled if it turns out to be a roaming
event later. Otherwise we notify SME and userspace the disconnection.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device sends connection terminated and [re]association success
(or failure) events when roaming occours. The patch uses
cfg80211_roamed instead of cfg80211_connect_result to notify SME
for roaming.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwm_cfg80211_get_station() should be static.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connect is called with the LEGACY_PSK authentication type set, and a
proper sme->key, we need to set the WEP key straight after setting the
profile otherwise the authentication will never start.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfg80211 requests to connect when we have already had an active
profile, invalidate the current profile first before sending a new
profile to UMAC.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since rndis_wlan is now converted to cfg80211, WIRELESS_EXT isn't
required anymore.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- remove double newlines between functions
- remove commented out function (rndis_set_config_parameter_u32())
- coding style fix in rndis_set_config_parameter_str()
- add comment banners between function sections
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As generic hw timer interrupt handler is moved to tasklet,
we no more need to call spin_lock_irqsave().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point handling this in hard irq, move it to
tasklet.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for dcbnl_rtnl_ops.setapp/getapp to set or get the current user
priority bitmap for the given application protocol. Currently, 82599 only
supports setapp/getapp for Fiber Channel over Ethernet (FCoE) protocol.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to the net_device_ops.ndo_fcoe_enable/disable for 82599. This
consequently allows us to dynamically turn FCoE offload feature on or off
upon incoming calls to ndo_fcoe_enable/disable. When this happens, FCoE offload
features are enabled/disabled accordingly, and this is regardless of whether
DCB being turned on or not.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly just simple conversions:
* ray_cs had bogus return of NET_TX_LOCKED but driver
was not using NETIF_F_LLTX
* hostap and ipw2x00 had some code that returned value
from a called function that also had to change to return netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are all drivers that don't touch real hardware.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update all the pcmcia network drivers for netdev_tx_t.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TUN driver lacks any LSM hooks which makes it difficult for LSM modules,
such as SELinux, to enforce access controls on network traffic generated by
TUN users; this is particularly problematic for virtualization apps such as
QEMU and KVM. This patch adds three new LSM hooks designed to control the
creation and attachment of TUN devices, the hooks are:
* security_tun_dev_create()
Provides access control for the creation of new TUN devices
* security_tun_dev_post_create()
Provides the ability to create the necessary socket LSM state for newly
created TUN devices
* security_tun_dev_attach()
Provides access control for attaching to existing, persistent TUN devices
and the ability to update the TUN device's socket LSM state as necessary
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: Eric Paris <eparis@parisplace.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Morris <jmorris@namei.org>
Doing an RTC reset when DMA is active may corrupt memory,
make sure no DMA is active at this moment by doing an
AHB reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old function rt2x00queue_payload_align() handled
both adding and removing L2 padding and some basic
frame alignment. The entire function was being abused
because it had multiple functions and the header length
argument was somtimes used to align the header instead
of the payload.
Additionally there was a bug when inserting L2 padding
that only the payload was aligned but not the header. This
happens when the header wasn't aligned properly by mac80211,
but rt2x00lib only moves the payload.
A secondary problem was that when removing L2 padding during
TXdone or RX the skb wasn't resized to the proper size.
Split the function into seperate functions each handling
its task as it should.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all values of the TX status enumeration were
covered during updating of the TX statistics. This
could lead to wrong bitrate tuning but also wrong
behavior in tools like hostapd.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rev1 2GHz and rev2 5GHz gain tables were incorrectly documented
on the specs originally. Update these gaintables to match the cor-
rected specs.
Signed-off-by: Gábor Stefanik <netroller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also mark the LP-PHY driver "802.11a/g" instead of "802.11g",
as LP-PHY is capable of both 2GHz and 5GHz operation.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-Make use of the b43_phy_set/mask/maskset helpers.
-Fix a few errors in the code.
-Make the code more readable.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Significant literature suggests users use debug flags 0x43fff - this causes
the debug flags to be set that causes information to be printed for every
received frame - including beacons. In the best case it fills up the logs,
at worst it slows driver down and causes failures due to timeouts.
In the RX handler, print debugging only if user requested RX debugging.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 does not have update_chain_flags defined and because if this we always
see the debug message that does not apply to it. Add a check to be specific
about what is actually happening.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some concerns were raised about the automatic adjustment
of sleep intervals to all the same, potentially high,
value, and I can imagine the hardware behaving better
when we don't ask too much of it.
So let's convert to use a succession of sleep levels
when requesting to go to deeper sleeps (which can only
happen with large DTIM intervals), using the succession
values from power level three, which have the benefit of
also having been tested extensively already.
As a result, the automatic sleep level adjustment will
now be mostly equivalent to power level three, except
for the RX/TX timeouts and possibly using smaller sleep
vectors to account for networking latency.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For HT packets, mac80211 expects the rate_idx to be an MCS number, which is the
lower byte of rate_n_flags. However, iwl_hwrate_to_plcp_idx takes the MCS
number and reduces it down to the range 0-8 (6 to 60 Mbps), removing the bits
that signify multiply streams, HT40 Duplicate mode, or unequal modulation.
This version is used for various internal purposes through the driver.
Add the function iwl_hwrate_get_mac80211_idx, an alternate version which takes
the rate and the band and returns the mac80211 index (MCS, for HT packets, and
PLCP rate, for legacy packets).
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor and correct rate selection for outgoing transmitted
packets.
First, note that HT rates in the mac80211 rate table do not provide valid
indices when ieee80211_get_tx_rate is called; the check to see if we could to
abort a transmission early in iwl_tx_skb() would thus occasionally read invalid
memory and occasionally stall transmission (if the erroneous byte was 0xff).
We remove that code; the check wasn't valid anyway.
Second, iwl_tx_cmd_build_rate() also called ieee80211_get_tx_rate to be used
for sending management packets, which do not use the uCode station table. This
patch refactors that function and adds comments to enhance legibility, replaces
the call to ieee80211_get_tx_rate() with a direct lookup, and adds error
handling in case the table entry is invalid.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_supported_band is supposed to only contain legacy rates in the
bitrates table (HT rates go in the ieee80211_sta_ht_cap substruct). Make
iwlwifi driver obey this restriction by removing the 60 Mbps rate. Also, clean
up a few pieces of other code that formerly relied on 60 Mbps being in
sband->bitrates.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If autonegotiation was disabled, we still set the
BMCR_ANENABLE and BMCR_ANRESTART, which resulted in autonegotiation
never being disabled.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reported-by: Julia Lawall <julia@diku.dk>
Single line log messages should be emitted by a single call
where possible.
Converted multiple calls to DBG_PRINT to single call form.
Removed "s2io:" preface from DBG_PRINTs.
The DBG_PRINT macro now emits a log level and is surrounded by
a do {...} while (0)
All s2io log output is now prefaced with KBUILD_MODNAME ": "
via pr_fmt.
The DBG_PRINT macro should probably be converted to use the
dev_<level> form eventually.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missed doing the conversion in earlier patch.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regularize the declaration and uses of
struct config_param *config = &sp->config;
struct mac_info *mac_control = &sp->mac_control;
and use
struct stat_block *stats = mac_control->stats_info;
struct swStat *swstats = &stats->sw_stat;
struct xpakStat *xstats = &stats->xpak_stat;
and convert the longish uses like
nic->mac_control.stats_info->sw_stat.<foo>
to
swstats-><foo>
etc.
This also makes the statistics code marginally smaller
and presumably faster.
Old:
$ size s2io.o
text data bss dec hex filename
114289 516 33360 148165 242c5 s2io.o
New:
$ size s2io.o
text data bss dec hex filename
114097 516 33360 147973 24205 s2io.o
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed trivial typo as well
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Still has a few long lines.
checkpatch was:
total: 263 errors, 53 warnings, 8751 lines checked
is:
total: 4 errors, 35 warnings, 8767 lines checked
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use consistent style. Don't calculate the kmalloc size multiple times
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Repeated variable use and line wrapping is hard to read.
Use temp variables instead of direct references.
struct fifo_info *fifo = &mac_control->fifos[i];
struct ring_info *ring = &mac_control->rings[i];
struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the tests that check whether Frame* bits are not set
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements suspend/resume and WOL support for UCC Ethernet
driver.
We support two wake up events: wake on PHY/link changes and wake
on magic packet.
In some CPUs (like MPC8569) QE shuts down during sleep, so magic packet
detection is unusable, and also on resume we should fully reinitialize
UCC structures.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes currently unused UGETH_MAGIC_PACKET Kconfig symbol
and code, i.e. magic_packet_detection_{enable,disable} functions.
The two functions each contain just two steps that we'll place into
suspend/resume code path under CONFIG_PM.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch factors out MAC initialization into ucc_geth_init_mac()
function that we'll use for suspend/resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 3e73fc9a12 ("ucc_geth: Fix IO
memory (un)mapping code") I fixed ug_regs IO memory leak by properly
freeing the allocated memory. But ethtool_stats() callback doesn't
check for ug_regs being NULL, and that causes following oops if
'ethtool -S' is executed on a closed eth device:
Unable to handle kernel paging request for data at address 0x00000180
Faulting instruction address: 0xc0208228
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0208228] uec_get_ethtool_stats+0x38/0x140
LR [c02559a0] ethtool_get_stats+0xf8/0x23c
Call Trace:
[ef87bcd0] [c025597c] ethtool_get_stats+0xd4/0x23c (unreliable)
[ef87bd00] [c025706c] dev_ethtool+0xfe8/0x11bc
[ef87be00] [c0252b5c] dev_ioctl+0x454/0x6a8
...
---[ end trace 77fff1162a9586b0 ]---
Segmentation fault
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the tx_prod, tx_cons, tx_pending, tx_ring, and
tx_buffers transmit ring device members to a per-interrupt structure.
It also adds a new transmit producer mailbox member (prodmbox) and
converts the code to use it rather than a preprocessor constant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the rx_rcb, rx_rcb_mapping, and rx_rcb_ptr return ring
device members to a per-interrupt structure. It also adds a new return
ring consumer mailbox register member (consmbox) and converts the code
to use it rather than a preprocessor constant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the last_tag, last_tag_irq, and hw_status device
members to a per-interrupt structure. It also adds a new interrupt
mailbox member (int_mbox) and converts the code to use it rather than a
direct preprocessor constant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the napi interrupt handler functions to accept and
use tg3_napi structures.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch migrates the ISR parameter from struct net_device to struct
tg3_napi. Checkpatch complains about the existence of the preexisting
IRQF_SAMPLE_RANDOM flag. I've opted to keep this patch conservative and
let it continue to exist until the flag gets officially purged from the
kernel.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a per-interrupt data structure, moves the napi
member over, and creates a tg3 pointer back to the device structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later patches will be adding MSIX support, which will complicate
interrupt initialization. This patch prepares for the integration by
breaking out the interrupt setup and teardown code into separate
functions and cleaning up the error return paths.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 only uses extended buffer descriptors for the jumbo producer
ring. Extended buffer descriptors are available on all devices that
support a separate jumbo producer ring so make the change universal.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch migrates most of the rx producer ring variables to a new
tg3_rx_prodring_set structure and modifies the code accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later patches are going to complicate the ring initialization routines.
This patch breaks out the setup and teardown of the rx producer rings
into separate functions to make the code more readable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch attempts to document the various rx buffer sizes used by the
driver and how they relate to each other.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves where the jumbo capable and msi support flags are
located. This is prep work for the addition of msix support flags.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch separates the code that sets up the mini producer ring from
the code that sets up the jumbo producer rings. The 5717 asic rev
devices do not have a mini ring, but do have a jumbo frame
implementation similar to the 5704 and previous devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes up the NVRAM detection switch statements to conform
to the kernel coding style.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device firmware uses the MDIO bus during early setup. If the driver
modifies the MDIO bus configuration while it is in use by the firmware,
any number of bad things can happen. This patch delays MDIO setup until
after the firmware posts its magic signature, signifying initialization
is complete.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method of ETHER_LINK pin is board dependence.
This patch adding paramters are:
- no_ether_link : If set to 1, do not use ETHER_LINK
- ether_link_active_low : If set to 1, ETHER_LINK is active low.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On TI's DA850/OMAP-L138 EVM, MAC address is stored in SPI
flash which is accessed using MTD interface.
This patch delays the initialization of DaVinci EMAC driver
by changing module_init to late_initcall. This helps SPI and
MTD drivers to get initialized before EMAC thereby enabling
EMAC driver to read the MAC address while booting and use it.
Tested with NFS on DM644x, DM6467, DA830/OMAP-L137 and
DA850/OMAP-L138 EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Reviewed-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Better small packet receive performance.
- Better handling of Flow control on 5709.
- Fixed iSCSI TMP ABORT TASK problem.
- Added iSCSI TCP timestamp option.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow the 10G iSCSI code to reuse the function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow the 10G iSCSI code to reuse the function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX completions were running in a workqueue queued by the ISR. This
patch moves the processing of TX completions to an existing RSS NAPI
context.
Now each irq vector runs NAPI for one RSS ring and one or more TX
completion rings.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we downshift to MSI/Legacy if we don't get enough vectors for
cpu_count RSS rings plus cpu_count TX completion rings. This patch
allows running MSIX with the vector count that the platform provides.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have three types of RX rings.
1) Default ring - services rx_ring for broadcast/multicast, handles
firmware events, and errors.
2) TX completion ring - handles only outbound completions.
3) RSS ring - handles only inbound completions.
This patch gets rid of the default ring type and moves it's functionality
into the first RSS ring. This makes better use of MSIX vectors since
they are a limited resource on some platforms.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bonding: Have bond_check_dev_link examine netif_running
Some network devices do not call netif_carrier_off when they
are set administratively down. Have the bonding link check function
also inspect the netif_running state. Ignore netif_running if the
bond_check_dev_link function is called with "reporting" set, as in that
case it's inspecting the capabilities of the non-netif_carrier device
driver.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
max_bonds is of type int and cannot be greater than INT_MAX.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding can use compare_ether_addr() in bond_release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propogate the vlan_features of the slave devices to the bonding
master device, using the same logic as for regular features.
Tested by Or Gerlitz <ogerlitz@voltaire.com>, who also removed
the debug logic from the original test patch.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the places in debugfs.c are missing a NULL check on the return value of
get_zeroed_page API call. Added required NULL check at appropriate places.
Signed-off-by: Kiran Divekar <kirandivekar@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that cfg80211 functions are added and wext converted to use wext-compat
functions, remove wext structures and disabled code.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stats worker no longer poll stats from device anymore. It's still
needed to poll device control channel for connect/disconnect events,
so rename stats worker as device poller.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add cfg80211 get_station and convert SIOCGIWRATE and get_wireless_stats
to cfg80211.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add cfg80211 add_key/del_key/set_default_key and convert wext to use theim.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add cfg80211 set_channel and convert wext to use it.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add cfg80211 connect functions for station and ad-hoc modes and
convert wext to use theim.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Random essid must be set to turn on radio when not connected. If device is
in ad-hoc mode, this results 'media connect' indications with the random
essid which should be ignored.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use is_zero_ether_addr() and is_broadcast_ether_addr() instead of
memcmp against ffff_bssid/zero_bssid.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move link up/down work to separate functions and use local array
for allocating memory for info structure instead of kzmalloc.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase scan delay from 1 sec to 6 sec. Spec says that scan by
OID_802_11_BSSID_LIST_SCAN completes in 6 seconds.
Before rfkill patch too short delay was not problem as device was
always active (radio on) and performing background scanning.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Buffer used for bssid list might be too small. Change rndis_query_oid()
to return required buffer length to caller and make rndis_check_bssid_list()
resize buffer when needed.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OID_802_11_BSSID_LIST_SCAN clears device's bssid list, so retrieve
current bssid list from device before issuing new scan.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting WPA keys with OID_802_11_ADD_KEY sometimes trigger
instant media connect indication. These indications are extranous and
should be ignored, as otherwise driver would send reassociation event to
userspace which in this case is not needed.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The A/G-PHY changes are fallout fixes from the enum change,
which in turn allows the LP-PHY code to be much simpler.
The antenna_to_phyctl change is a fix for a potential
existing bug that this patch may otherwise trigger.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The most common LP-PHY device, BCM4312, is now fully functional.
So, no need to say "probably won't work for you" anymore.
It's also not "for debuggers and developers only", as it is
perfectly usable for end-users now (at least for BCM4312).
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5K_SREV is available even if the chip has been put to sleep. Relying
on the chip register allows binding non-standard PCI IDs by
echo VENDOR_ID PRODUCT_ID >/sys/bus/pci/drivers/ath5k/new_id
without having to specify the driver data as well.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The `val' variable in ath5k_eeprom_read_turbo_modes() is used
uninitialized. gcc 4.4.1 with -fno-inline-functions-called-once reports
it:
eeprom.c: In function 'ath5k_eeprom_read_turbo_modes':
eeprom.c:441: warning: 'val' may be used uninitialized in this function
Comparing the code to the Atheros HAL, it's clear that the split between
ath5k_eeprom_read_modes() and ath5k_eeprom_read_turbo_modes() was
incorrect.
The Atheros HAL reads both turbo and non-turbo data from EEPROM in one
function. Some turbo mode parameters are derived from the same EEPROM
values as non-turbo parameters, just from different bits.
Merge ath5k_eeprom_read_turbo_modes() into ath5k_eeprom_read_modes() to
fix the warning. The actual values and offsets have been cross-checked
against Atheros HAL.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As Pavel Roskin noted, the check for mac version as copied from
legacy_hal made no sense. This replaces it with the equivalent
and makes up a suitable #define for the mac version legacy_hal
checked.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After some discussion on IRC about the PHY register write change,
I am not sure anymore if this is the right thing to do.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ICT IRQ table is a set of __le32 values, not u32 values,
so when reading it we need to take into account that it has
to be converted to CPU endianness. This was causing a lot of
trouble on my powerpc box where various things would simply
not work for no apparent reason with 5xxx cards, but worked
with 4965 -- which doesn't use the ICT table.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since patch "rt2x00: bss_info_changed() callback is allowed to sleep" the
variable delayed wasn't used anymore. This means it can be removed
along with the call to schedule_work which depended on that variable.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable"
functions, and use them during LP-PHY baseband init in b43.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-Fix a few nasty typos (b43_phy_* operations instead of b43_radio_*)
in the channel tune routines.
-Fix some typos & spec errors found by MMIO tracing.
-Optimize b43_phy_write & b43_phy_mask/set/maskset to use
only the minimal number of MMIO accesses. (Write is possible
using a single 32-bit MMIO write, while set/mask/maskset can
be done in 3 16-bit MMIOs).
-Set the default channel back to 1, as the bug forcing us to use
channel 7 is now fixed.
With this, the device comes up, scans, associates, transmits,
receives, monitors and injects on all channels - in other words,
it's fully functional. Sensitivity and TX power are still sub-optimal,
due to the lack of calibration (that's next on my list).
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Qdiv roundup routine is essentially a fixed-point
division algorithm, using only integer math.
However, the version in the specs had a major error
that has been recently fixed (a missing quotient++).
Replace Qdiv roundup with a rewritten, simplified version.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change implements rfkill support for RTL8187B and RTL8187L devices,
using new cfg80211 rfkill API.
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3-wire bluetooth coex support for AR9285.
This support can be enabled through btcoex_enable modparam.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need a hw cap bit for btcoex anymore as btcoex scheme type
is enough to do this.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also define macros for wlanactive and btactive (5 & 6) gpios.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure btcoex register configured with appropriate values
after it is initialized with the default values from initvals.h
during reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function currently does initialization + enable the
btcoex support. Split it into two logical functions which
does the above operations separately. Btcoex initialization
is done during attach time and enabling this feature is done
in start(). Also, add code to disable btcoex support in stop().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wlan does not set cipher suites list for cfg80211 which causes
wext-compat-range to report rndis_wlan not supporting WPA. Patch adds
cipher suites list and fixes NetworkManager not being able to connect to
WPA encrypted APs.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When dumping register contents, HW has to be awake.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PA Calibration is not needed for high power solutions.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* First PA driver (PDPADRV1) was not powered down properly.
* Compensation capacitor for dynamic PA was programmed incorrectly.
Also, remove a stray REG_READ.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PA calibration need not be done if the offset is not varying.
The current logic does PA calibration even if the offset is the
same.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initiate the conversion of libipw to the new cfg80211 configuration API.
For now, leave CONFIG_IPW2200_PROMISCUOUS stuff alone. Eventually
migrate it to cfg80211 when the add/del/change_virtual_intf methods
are implemented.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent a read of powInfo[-1] in the first iteration.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RC calibration code has some typos - fix them.
Also, make the default channel 7, as channel 1 is still
broken (only channels 7 and 8, and occasionally 9 work).
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/prism54/islpci_eth.o
drivers/net/wireless/prism54/islpci_eth.c: In function ‘islpci_eth_cleanup_transmit’:
drivers/net/wireless/prism54/islpci_eth.c:53: warning: cast from pointer to integer of different size
drivers/net/wireless/prism54/islpci_eth.c: In function ‘islpci_eth_receive’:
drivers/net/wireless/prism54/islpci_eth.c:453: warning: cast from pointer to integer of different size
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent ath5k hardware is capable of doing CCMP acceleration.
Enable it for the cards that support it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Save a memcpy by just storing updates directly in the skb
control block.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch, a compaq c700 can turn on the wifi led.
The array of compatible devices now includes the hardware
present in this computer, as well as the led pin and
polarity.
Signed-off-by: Marcos Chaparro <nitrousnrg@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The maze of if() statements in configure_filter is confusing.
Reorganizing it as a switch statement makes it more apparent what
is going on and reveals several suspicious settings. This has no
functional changes, though it does remove some redundant flags
that are set earlier.
Also now that we can sleep, protect sc->filter_flags with the
sc lock.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only print the driver version once, and condense all per-PHY
information to a single line.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add beacon control by BSS_CHANGED_BEACON_ENABLED and
bss_conf->enable_beacon from mac80211.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Intel Linux wireless folks can be reached via this address.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If NetworkManager is busy scanning when user
tries to unload the module, the driver can not be unloaded
because HW still scanning.
Make sure driver sends abort scan host command to uCode if it
is in the middle of scanning during driver unload.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix following error by sending synchronous command and waiting for the command
to complete.
mac80211-phy0: failed to remove key (0, ff:ff:ff:ff:ff:ff) from hardware (-16).
-16 is EBUSY error. The asynchronous command tests for STATUS_EXIT_PENDING
while interface is getting down and it returns -EBUSY error if set.
Changing the host command from asynchronous call to synchronous call
enables command to be run while interface is going down.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6000 series and up, additional enhanced regulatory tx power
limitation information is added to EEPROM image.
In order to setup the tx power limitation per channel correctly. Read
the enhanced tx power information from EEPROM image and update
accordingly.
The information is provided per SISO (a,b,c) chain based, it also has
information for both MIMO2 and MIMO3. For tx power regulatory
limitation, take the highest number from all the chains and update.
Also update tx_power_user_lmt to the highest power supported by any
channels and chains
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add code to set the HT flags (HT, 40 MHz, Short guard interval) in
the ieee80211_rx_status field passed to mac80211. This ensures that mac80211
processes these HT packets correctly.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clear the flags (most importantly, the IEEE80211_TX_RC_MCS flag)
when sending a non-HT packet so that the rate index can be properly treated.
This fixes the reporting of legacy rates in wireless-extensions for packets
sent after an HT packet.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugFs file show current tx power for all the transmit chains
Adding "tx_power" file in /sys/kernal/debug/ieee80211/phy0/iwlagn/debug
to display current tx power for all the active chains in 1/2 dB step.
Show tx power information "Not available" if uCode can not provide the
information or interface is down.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
uCode version changed to v4 for 6000 series
The additional parameter added to v4 is providing current tx power for
each chain in tx statistics portion of "statistics notification"
command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Perform error checking and report failure when setting tx power from
sysfs.
If fail to set the tx power, do not update the local copy, so user will
not see the incorrect tx power in sysfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changing the name from "tx_power_channel_lmt" to "tx_power_device_lmt";
to give idea that scope of limit is for overall device, not any
individual channels
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting tx power in sysfs, check against max channel tx power
limit instead of IWL_TX_POWER_TARGET_POWER_MAX.
Different devices have different max tx power limit; using
IWL_TX_POWER_TARGET_POWER_MAX can excess the limitaion and give wrong
information.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the tx_power_user_lmt to the lowest power level
this value will get overwritten by channel's max power avg
from eeprom
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 1ccb84d87d04df3c76cd4352fe69786d8c7cf016 by Wey-Yi Guy
("iwlwifi: clean up unused NL80211_IFTYPE_MONITOR for Monitor mode")
broke injection of non-broadcast frames to unassociated stations
(causing a SYSASSERT for all such injected frames), due to injected
frames no longer automatically getting a broadcast station ID assigned.
This patch restores the old behavior, fixing the aforementioned
regression.
Also, consistently check for IEEE80211_TX_CTL_INJECTED instead of
iwl_is_monitor_mode in the TX path, as TX_CTL_INJECTED specifically
means that a given packet is coming from a monitor interface, while
iwl_is_monitor_mode only shows whether a monitor interface exists
on the device.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CF8305 is a very old silicon running firmware version 3.0 . This card also
needs some special treatment as it's so old it can't do unaligned register
access. But since that happens only at one place, there were no changes made to
the register access functions, but instead that particular place was fixed.
Also, this card uses only one-stage firmware which is loaded the same way as
helper firmware. The second-stage firmware isn't loaded on this card and doesn't
therefore have to be supplied.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clarify what the heck the function is doing with better variable names
and less indirection and better comments. Also ensure callers use the
proper minimum size, even though all rates arrays should be size
MAX_RATES anyway. Reverts part of Andrey's dynamic alloc patch since we
don't really need it. Also leaves the passed-in rates array alone on
errors.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check whether index is within bounds before testing the element.
(also includes "Libertas: Association request to the driver failed"
The size of the tmp buffer was too small, causing a regression
rates->rates has an arraysize of 1, so a memcpy with
MAX_RATES (14) was already causing reads out of bounds.
In get_common_rates() the memset/memcpy can be moved upwards. -- JWL)
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX chainmasks were set to 1x1 during scanning.
Configure them properly with the values retrieved from
the EEPROM.
Also, this requires scan_start/scan_end callbacks to be
locked with sc->mutex.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This eliminates the dual definition of ieee80211_channel (and possibly
others), further clarifying who defines what and paving the way for
inclusion of cfg80211.h.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add_wep_key() tries to check if key length is not 5 AND not 13
but uses (key_len != 5 || key_len != 13) instead. Fix this.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for FIF_OTHER_BSS was missing. This patch adds support for this
filtering mode which in turn resolves a problem where mesh interfaces would not
receive broadcast traffic.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch "mac80211: fix PS-poll response race" somehow broke
broadcast buffering in a funny way.
During normal operation - stations are awake - the firmware refused
to transmit broadcast frames and reported P54_TX_PSM_CANCELLED.
But everything worked as soon as one station entered PSM.
The reason:
The stack sets IEEE80211_TX_CTL_SEND_AFTER_DTIM for outgoing
broadcast frames as soon as a station is marked as sleeping.
This flag triggers a path which will reroute these frames
into p54's "content after beacon" queue, which is designed
to cope with the demands for psm.
This patch restores the old behavior.
IEEE80211_TX_CTL_CLEAR_PS_FILT will once again be used to signalize
the firmware to ignore the ps canceling for certain frames.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bartlomiej Zolnierkiewicz reported an atomic order-6 allocation failure
for ipw2200 firmware loading in kernel 2.6.30. High order allocation is
likely to fail and should always be avoided.
The patch fixes this problem by replacing the original order-6
pci_alloc_consistent() with an array of order-1 pages from a pci pool.
This utilized the ipw2200 DMA command blocks (up to 64 slots). The
maximum firmware size support remains the same (64*8K).
This patch fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14016
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reconfiguring the port requires us to flush all DMA queues. In
repeated testing we have found that RX flushes would sometimes fail
because the RX DMA engine was not properly isolated from the MACs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Received frames must be re-clocked by the local XGXS to the 156.25 MHz
(DDR) clock of the XGMII. If the remote clock is slightly faster this
can reduce a minimum IPG of 64 bit-times (1 cycle) to 32 bit-times
(half a cycle). If the XMAC detects that a frame has reached the
maximum RX frame length in the same cycle that it receives one of
these reduced IPGs, it may miss the IPG, causing two valid frames to
be treated as a single invalid frame (over-length with bad CRC).
We work around this by increasing the maximum RX frame length so that
peers with matched MTU will not provoke this bug.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At probe time, falcon_reset_hw() performs a hard reset of the PHY
along with Falcon. There is no need to perform a soft reset later,
and any access to standard MDIO registers before the PHY firmware has
booted can interrupt the boot process, making the port unusable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs will report that the link is up even though there is a fault
condition. Therefore, check the fault flag too. We must also read
STAT2 to reset this flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
falcon_reset_xaui() waits for XGXS reset to complete, but the XAUI
serdes reset may take longer. It needs to check both reset active
bits.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must call netif_carrier_off() after the device is registered, not
before, to set the operational state and user-space IFF_RUNNING flag
correctly.
Since we don't want observers to see an intermediate state, open-code
register_netdev() and add efx_update_name() and netif_carrier_off()
into the locked region.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.100.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings the 57780's phy into IEEE compliance by suppressing the
common mode oscillation.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the AC131 fast ethernet transceiver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the BCM50610M phy ID.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the code to use the PHY_IS_FET flag rather than the
ASIC revision to decide whether or not to use FET paths.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom's phys come in two distinctly different register layouts. For
the lack of an official term to distinguish between the two formats, we
can loosely categorize them by their fast ethernet or gigabit ethernet
transceiver description. This patch creates the (driver-internal) Fast
Ethernet Transceiver (FET) namespace and converts the 5906 EPHY
definitions over.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tunes the timeouts the CPMU uses to decide when to switch
from the clocks output by the PHY to internal clock sources.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 57788 and removes support for the 57720
which was never released.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most older tg3 devices only supported a PCIe maximum payload size of
128 bytes. More recent devices bump this limit up to 256 bytes
though. This patch modifies the code so that the MPS limit is only
enforced on those devices that only allow the 128 byte setting.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall discovered that the TG3_FLG2_TSO_CAPABLE flag was being
compared against the wrong flags device member. This patch implements
the fix.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prevents a tx BD corruption bug by preventing the device from
powering down the PLL from L1 if the link speed is 10Mbps or 100Mbps.
The same bits are also used to prevent a system hang during chip reset
resulting from a complicated set of events that ultimately leads to
PCIe block register corruption.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some PCIe link receiver errors by decreasing the internal
electrical idle timeout.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove function e1000_mta_set, as it is no longer called
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were already exporting TSO6 to the vlan, but we weren't exporting the
checksum support for IPV6 which was causing warning messages to be
displayed when doing IPv6 TSO over a vlan.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some ~40 functions that were being called out with 'make
namespacecheck'. This patch changes these functions to be static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ethtool get_settings logic to report 10G & 1G advertised and
supported link modes in all 8259x 10G backplane connection types
except for 82598EB BX network connection type.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface is put in bridged mode, destination mac
addresses are unknown to firmware. So packets take a slow
path (lower priority) in firmware reducing performance.
Firmware can cache limited number of remote unicast mac
addresses for certain interval, if "dynamic mac learning"
mode is enabled.
Driver needs to enable this "mac learning" mode in firmware.
Currently this is done through net device class sysfs entry,
possibly this can also be done upon netlink notifications to
from bridge.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate all MAC/PHY access functions into netxen_nic_hw.c
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement common function for locking/unlocking 8 hardware
semaphores used for serializing access to shared resouces
on a NIC board by different PCI functions.
As by definition, callers of these semaphore API can be
put to sleep till the semaphore is locked.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove code for phy access on unreleased NX2031 based quad-gig board.
NX3031 based production quad-gig boards do not require direct phy
access by driver.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we run out of memory, use keventd to fill the buffer. There's a
report of this happening: "Page allocation failures in guest",
Message-ID: <20090713115158.0a4892b0@mjolnir.ossman.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect
net_device_ops). Do the same for sa1100_ir.
Untested.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect
net_device_ops). Do the same for au1k_ir.
Untested.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETPOLL requires that interrupts remain disabled in its callbacks.
Using *_irq_save()/irq_restore() to replace *_irq_disable()/irq_enable()
functions in NETPOLL's callbacks of smc91x, so that it doesn't enable
interrupts when already disabled, and kgdboe/netconsole would work
properly over smc91x.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes broken pxaficp-ir. The problem was in incorrect
net_device_ops being specified which prevented the driver from
operating. The symptoms were:
- failing ifconfig for IrLAN, resulting in
SIOCSIFFLAGS: Cannot assign requested address
- irattach working for IrCOMM, but the port stayed disabled
Moreover this patch corrects missing sysfs device link.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb(). The use of "A functions set" in the NETPOLL API
callbacks causes the interrupts to get enabled and can lead to kernel
instability.
The solution is to use "B functions set" to prevent the irqs from
getting enabled while in netpoll_send_skb().
A functions set:
local_irq_disable()/local_irq_enable()
spin_lock_irq()/spin_unlock_irq()
spin_trylock_irq()/spin_unlock_irq()
B functions set:
local_irq_save()/local_irq_restore()
spin_lock_irqsave()/spin_unlock_irqrestore()
spin_trylock_irqsave()/spin_unlock_irqrestore()
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andreas Mohr <andi@lisas.de>
Acked-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of fully initializing an unusable second r6040
device, perform the PHY detection earlier and bail out
in r6040_init_one when we could not read the PHY identifier.
Signed-off-by: Mark Kelly <mark@bifferos.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unused pioaddr variable.
Signed-off-by: Mark Kelly <mark@bifferos.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Data in descriptors is
accessed simultaneously by the chip (writing status and size when
a packet is received) and CPU (reading to check if the packet was
received). This isn't a valid usage of PCI DMA API, which requires use
of the coherent (consistent) memory for such purpose. Unfortunately e100
chips working in "simplified" RX mode have to store received data
directly after the descriptor. Fixing the driver to conform to the API
would require using unsupported "flexible" RX mode or receiving data
into a coherent memory and using CPU to copy it to network buffers.
This patch, while not yet making the driver conform to the PCI DMA API,
allows it to work correctly on X86 with swiotlb (while not breaking
other architectures).
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate register definitions in netxen_nic_hdr.h
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement pci driver shutdown functionality, this helps
quiescing all PCI transaction before chipset is reset.
Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all tx skb mapping code into netxen_map_tx_skb().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netxen_need_fw_reset() return 0 [ implies firmware is up
and running], still go through dma mask check, etc.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool -K knob to control LRO in firmware.
LRO path is completely separated from GRO, LRO packets
are still fed with netif_receive_skb().
Also fix ethtool statistics to include LRO packets.
Also use correct message type while configuring interrupt coalescing.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure, once initialized, never changes.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Set the USE_INT_PARAM bit so the rx-frames-irq and tx-frames-irq will take
effect on 5709.
- Increase the default rx-frames to reduce interrupt count.
- Decrease the default rx-frames-irq and tx-frames-irq to catch more events
during NAPI poll.
All these will reduce interrupts without affecting latency.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report this counter to ethtool -S and include it in netstat.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unable to allocate memory for new MTU or new ring size, we need
to close the device to prevent it from crashing.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this check to bnx2_netif_stop() and bnx2_vlan_rx_register() to
prevent bus lockups on some systems when the chip is in low power state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case IRQs are shared, we will not mistakenly start processing
the ring based on old status block indices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8187B always needs MSR_LINK_ENEDCA flag to be set even when it is in
no link mode, otherwise it'll not be able to associate when this flag is
not set after the change "mac80211: fix managed mode BSSID handling".
By accident, setting BSSID of AP before association makes 8187B to
successfuly associate even when ENEDCA flag isn't set, which was the
case before the mac80211 change. But now the BSSID of AP we are trying
to associate is only available after association is successful, and
any attempt to associate without the needed flag doesn't work.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current mwl8k_priv->fw_lock spinlock doesn't actually protect
against multiple commands being submitted at once, as it is not kept
held over the entire firmware command submission. And since waiting
for command completion sleeps, we can't use a spinlock anyway.
To fix mwl8k firmware command serialisation properly, we have the
following requirements:
- Some commands require that the packet transmit path is idle when
the command is issued. (For simplicity, we'll just quiesce the
transmit path for every command.)
- There are certain sequences of commands that need to be issued to
the hardware sequentially, with no other intervening commands.
This leads to an implementation of a "firmware lock" as a mutex that
can be taken recursively, and which is taken by both the low-level
command submission function (mwl8k_post_cmd) as well as any users of
that function that require issuing of an atomic sequence of commands,
and quiesces the transmit path whenever it's taken.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete most of the mwl8k_work_struct fields and options, since most
of them are unused or never changed from their defaults:
- We always use priv->config_wq, so delete the wqueue argument from
mwl8k_queue_work().
- MWL8K_WQ_SPIN and MWL8K_WQ_POST_REQUEST are never used, as all
callers sleep for request completion, so sleep unconditionally.
- MWL8K_WQ_FREE_WORKSTRUCT is never used.
- MWL8K_WQ_TX_WAIT_EMPTY is always set, so assume it unconditionally.
- timeout_ms/txwait_attempts/tx_timeout_ms are never changed from
their defaults, so just hardcode these in the workqueue worker.
- step is never used.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various mwl8k_txq_xmit changes:
- Extract the QoS field before adding the DMA header.
- Only write to tx->status once, and only after all the other
descriptor fields have been set.
- Do all tx state manipulation under the tx spinlock.
- Remove the priv->inconfig check, as all transmit queues will
be frozen during config cycles, so we won't ever be asked to
transmit if a config cycle is running.
- Remove some more dead code.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use MWL8K_TX_QUEUES instead of a hardcoded "4" in a couple of places.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since firmware load commands don't generate 'command done' interrupts
like normal commands do, polling for command done interrupts just
unnecessarily slows down the firmware load process. Removing this bit
of code speeds up loading a typical firmware image from 840 msec to
180 msec.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding and removing the DMA header that the mwl8k hardware requires
on tx and provides on rx can never fail, since we are guaranteed to
have enough headroom on the tx path to expand the packet, and we only
ever shrink the packet on the rx path. (And on both paths we are
guaranteed to be the only user of the skb we are handling.)
This allows removing all of the skb clone handling in the tx and tx
reclaim paths, and eliminates error checks in both the tx and rx
paths, simplifying the code a bit more.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to check for NL80211_IFTYPE_MONITOR in
->add_interface(), as this function is never called for monitor
interfaces. Also, there is no need to advertise this bit in our
wiphy's ->interface_modes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k_configure_filter() passes pointers to total_flags and the
multicast address list to a workqueue function, while there is no
guarantee that those pointers will still be valid by the time the
workqueue function runs.
Solve this by passing total_flags by value, and by passing an
already built multicast address setup command packet to the workqueue
function so that we don't have to look at the multicast address list
itself outside of mwl8k_configure_filter().
Also, since ->configure_filter() can sleep now, wait synchronously
for the worker to finish.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of passing a flag bitmask to mwl8k_cmd_802_11_radio_control,
pass the 'enable' and 'force' arguments as separate parameters, and
introduce wrappers for the common cases of enabling and disabling
without forcing.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Other than ns_avgbrssi (Average beacon rssi) no data of
ath9k_node_stats is being used anywhere. Nuke this structure
and move its only useful member to ar5416Anistate. Also cleanup
this redundant data in ath_softc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the beacon rssi that LPF gives is divided and rounded
up by ATH_RSSI_EP_MULTIPLIER twice. This will leave the incorrect rssi
in ANI. Having correct rssi in ANI fixes the connection stability at
< 30dB rssi range. This patch removes the unncessary computation of average
rssi over already valid average rssi. Also removes the redundant macros to
find average rssi.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This add hardware tkip for b43.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry has started re-checking all current routines against a new
version of the Broadcom MIPS driver. This patch implements the first
round of changes he documented on the specs wiki.
Also remove a few FIXMEs regarding missing initial values for variables
with dynamic initial values where reading the values has been implemented.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thanks to "mac80211: allow configure_filter callback to sleep",
we no longer have to defer the work to the workqueue.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The specs are beginning to support rev3 LP-PHYs - implement one of
the changes needed for rev3 support.
Also, in the new MIPS driver, the "Japan TX filter" was renamed to
"analog TX filter init" - however, calling it "init" is confusing,
so name it "set analog filter", with a comment for easier future
identification.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bss_info_changed() callback function no longer needs
to be atomic. Remove the scheduled work structure and
call into the driver directly.
Additionaly this makes the DRIVER_REQUIRE_SCHEDULED
flag redundant so it can be removed.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The configure_filter() callback function no longer needs
to be atomic. Remove the scheduled work structure and
call into the driver configure_filter() directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes:
CHECK drivers/net/wireless/ipw2x00/ipw2100.c
drivers/net/wireless/ipw2x00/ipw2100.c:7888:22: warning: symbol 'mode' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2100.c:188:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2100.c:7952:18: warning: symbol 'mode' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2100.c:188:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2100.c:8000:18: warning: symbol 'mode' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2100.c:188:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2100.c:8268:27: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2100.c:8268:27: originally declared here
drivers/net/wireless/ipw2x00/ipw2100.c:8268:27: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2100.c:8268:27: originally declared here
drivers/net/wireless/ipw2x00/ipw2100.c:8268:27: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2100.c:8268:27: originally declared here
CC [M] drivers/net/wireless/ipw2x00/ipw2100.o
CHECK drivers/net/wireless/ipw2x00/ipw2200.c
drivers/net/wireless/ipw2x00/ipw2200.c:847:13: warning: symbol 'led' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:92:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:891:13: warning: symbol 'led' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:92:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:935:13: warning: symbol 'led' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:92:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:980:13: warning: symbol 'led' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:92:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:1016:13: warning: symbol 'led' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:92:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:1051:13: warning: symbol 'led' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:92:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:1823:13: warning: symbol 'channel' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:86:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min1' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: warning: symbol '_min2' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:4268:19: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:6228:28: warning: symbol 'channel' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:86:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:6369:20: warning: symbol 'channel' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:86:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:6857:12: warning: symbol 'mode' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:87:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:7964:13: warning: symbol 'channel' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:86:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:8720:12: warning: symbol 'channel' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:86:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:9662:13: warning: symbol 'mode' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:87:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:9720:13: warning: symbol 'mode' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:87:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:9826:13: warning: symbol 'mode' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:87:12: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:10318:21: warning: symbol 'remaining_bytes' shadows an earlier one
drivers/net/wireless/ipw2x00/ipw2200.c:10184:13: originally declared here
drivers/net/wireless/ipw2x00/ipw2200.c:8338:45: warning: cast to restricted __le16
drivers/net/wireless/ipw2x00/ipw2200.c:4414:21: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ipw2x00/ipw2200.c:4414:21: expected restricted __le16 [usertype] size
drivers/net/wireless/ipw2x00/ipw2200.c:4414:21: got unsigned short [unsigned] [usertype] <noident>
drivers/net/wireless/ipw2x00/ipw2200.c:6105:33: warning: incorrect type in initializer (different base types)
drivers/net/wireless/ipw2x00/ipw2200.c:6105:33: expected restricted __le16 [usertype] tx_rates
drivers/net/wireless/ipw2x00/ipw2200.c:6105:33: got unsigned short [unsigned] [usertype] rates_mask
drivers/net/wireless/ipw2x00/ipw2200.c:6124:29: warning: bad assignment (>>=) to restricted __le16
drivers/net/wireless/ipw2x00/ipw2200.c:6130:31: warning: restricted __le16 degrades to integer
drivers/net/wireless/ipw2x00/ipw2200.c:6140:23: warning: restricted __le16 degrades to integer
drivers/net/wireless/ipw2x00/ipw2200.c:6149:54: warning: restricted __le16 degrades to integer
drivers/net/wireless/ipw2x00/ipw2200.c:6151:37: warning: invalid assignment: &=
drivers/net/wireless/ipw2x00/ipw2200.c:6151:37: left side has type restricted __le16
drivers/net/wireless/ipw2x00/ipw2200.c:6151:37: right side has type int
drivers/net/wireless/ipw2x00/ipw2200.c:6154:54: warning: restricted __le16 degrades to integer
drivers/net/wireless/ipw2x00/ipw2200.c:6156:37: warning: invalid assignment: &=
drivers/net/wireless/ipw2x00/ipw2200.c:6156:37: left side has type restricted __le16
drivers/net/wireless/ipw2x00/ipw2200.c:6156:37: right side has type int
drivers/net/wireless/ipw2x00/ipw2200.c:6159:55: warning: restricted __le16 degrades to integer
drivers/net/wireless/ipw2x00/ipw2200.c:6161:37: warning: invalid assignment: &=
drivers/net/wireless/ipw2x00/ipw2200.c:6161:37: left side has type restricted __le16
drivers/net/wireless/ipw2x00/ipw2200.c:6161:37: right side has type int
drivers/net/wireless/ipw2x00/ipw2200.c:6164:29: warning: invalid assignment: |=
drivers/net/wireless/ipw2x00/ipw2200.c:6164:29: left side has type restricted __le16
drivers/net/wireless/ipw2x00/ipw2200.c:6164:29: right side has type unsigned short
drivers/net/wireless/ipw2x00/ipw2200.c:7853:29: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ipw2x00/ipw2200.c:7853:29: expected signed char [signed] [usertype] [explicitly-signed] rt_dbmnoise
drivers/net/wireless/ipw2x00/ipw2200.c:7853:29: got restricted __le16 [usertype] noise
drivers/net/wireless/ipw2x00/ipw2200.c:7967:25: warning: incorrect type in initializer (different base types)
drivers/net/wireless/ipw2x00/ipw2200.c:7967:25: expected signed char [signed] [usertype] [explicitly-signed] noise
drivers/net/wireless/ipw2x00/ipw2200.c:7967:25: got restricted __le16 [usertype] noise
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/wl12xx/wl1271_main.o
drivers/net/wireless/wl12xx/wl1271_main.c: In function ‘wl1271_op_add_interface’:
drivers/net/wireless/wl12xx/wl1271_main.c:611: warning: ‘print_mac’ is deprecated (declared at include/linux/if_ether.h:142)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the shared regulatory structure into the
common structure. We will use this ongoing for common
data.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k_stop(), tx_complete_work was being cancelled twice.
This patch fixes it. Also, locking sc->mutex should be done
at the beginning.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After initial power-up, the embedded cpu is usually halted. However,
if we down the interface and only do a soft reset before bringing
the interface back up, it will still be running and the firmware
loading code will bail out. This change halts the CPU before loading
the firmware, enabling a second call to wl1251_boot() to succeed
without a hard reset.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci can handle different retry rates,
it will always step 1 rate down after a failed
transmission so creating the retry rate list
for mac80211 is quite simple.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the original Ralink driver,
LG_FBK_CFG0_OFDMMCS2FBK should be initialized to 9 rather then 3.
Based on a patch for rt2800pci from Benoit
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the TX descriptor the Packet ID must not be 0,
so add 1 to the ID. The wireless CLI ID is not allowed
to be 0 either, but also must be initialized with the
wcid value rather then keyid.
Based on a patch for rt2800pci from Benoit
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the RX descriptor indicates the frame was L2 padded,
the SKBDESC_L2_PADDED flag should be set to make sure the
L2 padding is removed before it is send to mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new defines for RF chipsets which can be found
by the driver. We don't have to check for these
chips specifically yet, but it is better to have
the defines in now.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed comments about SHARED_KEY_TABLE_BASE and SHARED_KEY_MODE_BASE.
Fixed initialization loop for SHARED_KEY_MODE_ENTRY.
Based on a patch for rt2800pci from Benoit.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill_poll callback function in the drivers check a bit
to see if the RFKILL key has been pressed. However when the
bit is set it means the radio is active and the device can be
used.
The wiphy_rfkill_set_hw_state() function expects the inversed,
so '1' must be send when the radio must be disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call set_tx_power_control with a LPPHY_TXPCTL rather than an
LPPHY_TX_PWR_CTL_CMD_MODE.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the mode the hardware is in, not the mode we used the last time.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ACX_SLV_SOFT_RESET_BIT and ACX_REG_EEPROM_START_BIT are both defined
as "1" in the vendor driver code, but they were defined to be BIT(1)
("2") here.
The SOFT_RESET typo ensures that wl1251_boot_soft_reset() doesn't;
as a result the device hangs when trying to reprogram the PLL
registers while running.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All but two drivers have now stopped using the two
deprecated members radio_enabled and beacon_int,
so it's about time to remove them for good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry has reported success getting scan data with an LP-PHY device,
so it's probably time to release LP-PHY support for testing.
Also disable 802.11a support for now, as 802.11a currently causes
the driver to panic on startup (NULL pointer dereference).
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The spec for initializing the B2062 radio have changed recently,
update the code to match the changes.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I missed the "+16" part of the instruction in the specs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few typos have been discovered in both the specs and the code.
This patch fixes them.
Also use lpphy_op_switch_channel consistently, and make all users
of it print its return value for easier debugging.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel switch routine had a whole instruction missing. Add it.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The spec had some nasty typos, and a large part of the rev0/1 BB
init procedure was also missing. Fix these.
Also make the init-time channel switch debuggable.
(The change from -EINVAL to -EIO is simply to make it possible
to distinguish the PLL charge pump error from a channel-not-found
error.)
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't drop all packets received from an LP-PHY with WARN_ON.
Also update a comment with LP-specific information.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should fix the remaining WARN_ON.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rev2+ never needs to have gain tables adjusted according to the spec.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-Enable rate memory init for LP-PHY (same as G and N-PHY).
-Mark rev.2 LP-PHYs with the B2063 radio as supported.
-Allow using the 5GHz band on LP-PHYs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for loading LP-PHY firmware to b43_try_request_fw.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes kindly pointed out that I completely missed a hunk in
his patch: "[PATCH] cfg80211: allow driver to override PS default".
The driver must explicitly set ps_default to false,
as the setting is pre-filled with the kconfig default.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable AsyncFIFO and AGGWEP for AR9287_12 and later revisions only.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-Move pdiv from lpphy_2062_init to struct b43_phy_lp.
-Add channel table for the B2062 radio.
-Add code for tuning the B2062 radio to channel.
-Add error handling to op_switch_channel, and use it for both radios.
Rev0/1/B2062 will now hopefully show some signs of life, though
it won't work at full performance, as calibration is still missing.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rev.2+/B2063 will now hopefully show some signs of life, though
it won't work at full performance, as calibration is still missing.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse complains about a bad constant expression due to the use of a
dynamic-sized array in get_common_rates(). Allocate and free the array
instead.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unfortunately, PS currently affects RX performance
significantly enough to warrant disabling it by
default, but give the user the choice to enable it
again with iwconfig.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The field called 'len' in struct iwl_rx_packet is in fact not just a length
field but also includes some flags from the flow handler. In several places
throughout the driver, this causes incorrect values to be interpreted as
lengths when the field is improperly masked.
In most situations the improper use is for debugging output, and simply results
in an erroneous message, such as:
[551933.070224] ieee80211 phy0: I iwl_rx_statistics Statistics notification received (480 vs -1367342620).
which should read '(480 vs 484)'.
In at least one case this could case bad things to happen:
void iwl_rx_pm_debug_statistics_notif(struct iwl_priv *priv,
struct iwl_rx_mem_buffer *rxb)
{
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
IWL_DEBUG_RADIO(priv, "Dumping %d bytes of unhandled "
"notification for %s:\n",
le32_to_cpu(pkt->len), get_cmd_string(pkt->hdr.cmd));
iwl_print_hex_dump(priv, IWL_DL_RADIO, pkt->u.raw, le32_to_cpu(pkt->len)
);
}
EXPORT_SYMBOL(iwl_rx_pm_debug_statistics_notif);
Given the rampant misuse of this field without proper masking throughout the
driver (every use but one), this patch renames the field from 'len' to
'len_n_flags' to reduce confusion. It also adds the proper masking when
this field is used as a length value.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding legacy thermal throttling management support to 5150 NIC
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Green-field mode should be configured in the HT station table. This patch uses
both the per-station GF support flag as well as the current BSS HT operation
mode (non-GF stations present flag).
Added the "ht_greenfield_support" field to struct iwl_cfg to replace the
device-specific check in rs_use_green(). That check has been moved to
iwlcore_init_ht_hw_capab().
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Short guard interval support is a local per-station parameter not a global
per-NIC parameter. (mac80211 will correctly remove SGI support from station
capabilities if the BSS does not permit it). This patch removes the short GI
support bitfield from the global iwl_ht_info struct and properly uses
per-station HT capabilities during rate selection.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As indicated by note in iwl_ht_conf, some HT parameters are set on association
(e.g., channel width) and some vary over time (HT protection mode) and per
station (e.g., short GI support). The global parameters should be set in
iwl_mac_config and the local/varying parameters in iwl_ht_conf.
This patch moves the channel width configuration from iwl_ht_conf to
iwl_mac_config, and defers further cleanup of the local/global conflation for a
later patch.
This fixes a bug in using HT40 channels in some modes.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a number of issues in iwl_rx_reply_rx and
iwl_pass_packet_to_mac80211. These issues stem from the complexities of
managing two different types of packet commands for different hardware.
- Unify code handling rx_phy_res in SKB or cached to eliminate redundancy and
remove potential NULL pointer accesses
- Replace magic number with proper constant
- Optimize functions by moving early exit conditions before computation
- Comment code and improve some variable names
- Remove redundant computation in iwl_pass_packet_to_mac80211 by passing in the
correct, already-computed arguments.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some members of iwl_ht_info are unused, and one of
them is write-only, so we can remove these three:
max_amsdu_size, ampdu_factor and mpdu_density.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For devices using OTP memory, EEPROM image can start from
any one of the OTP blocks. If shadow RAM is disabled, we need to
traverse link list to find the last valid block, then start the EEPROM
image reading.
If OTP is not full, the valid block is the block _before_ the last block
on the link list; the last block on the link list is the empty block
ready for next OTP refresh/update.
If OTP is full, then the last block is the valid block to be used for
configure the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch cleans up the HT40 extension channels setup for EEPROM
band 6 and 7 to make it more readable.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver's first notification of a new station from mac80211 can be through rate
selection API. This patch fixes a bug where, in this code path, the HT
capabilities of the new station were ignored.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx_chan_width entry is never used, supported_chan_width is used instead.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With EDCA and HCCA we have 16 potential tid values. This is accommodated by
mac80211, but iwlwifi only supports EDCA. With this implementation it is
thus possible for mac80211 to request a tid that will cause iwlwifi to read
outside array bounds. A similar problem exists if traffic is received in an
unsupported category.
We add error checking to catch these situations.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW TX power control init still needs work.
The SW init is complete according to the specs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The V4 dummy transmission has two extra bools in its prototype,
so update all callers with the 2 bools.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the Xilinx Ethernet Lite device. The
soft logic core from Xilinx is typically used on Virtex and Spartan
designs attached to either a PowerPC or a Microblaze processor.
Signed-off-by: Sadanand M <sadanan@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ibm_newemac netdev instance is shutdown with "ifconfig down",
the netdev interface does not go properly down. netif_carrier_ok()
keeps returning TRUE even after "ifconfig down".
The problem can be seen when ibm_newemac instances are slaves of
a bonding interface. The bonding interface code uses netif_carrier_ok()
to determine the link status of its slaves. When ibm_newemac slave is
shutdown with "ifconfig down", the bonding interface won't detect any
link status change because netif_carrier_ok() keeps returning TRUE.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's too stupid to see that we always set flen to something
before we use it in ppp_mp_explode():
drivers/net/ppp_generic.c: In function 'ppp_push':
drivers/net/ppp_generic.c:1314: warning: 'flen' may be used uninitialized in this function
drivers/net/ppp_generic.c:1314: note: 'flen' was declared here
This started warning after commit a53a8b5682
("ppp: fix lost fragments in ppp_mp_explode() (resubmit)")
So just put an explicit unconditional initialization there to
hush it up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build errors due to missing Kconfig select of CRC32:
ks8851.c:(.text+0x7d2ee): undefined reference to `crc32_le'
ks8851.c:(.text+0x7d2f5): undefined reference to `bitrev32'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to I modified the corresponding platform device name,
so I make the patch to rename MAC platform driver
for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recycling turns out to be a bad idea! For most use cases, the
packet can not be reused: TCP packets are cloned. Even for the ideal
case of forwarding, it hurts performance because of CPU ping/pong.
On a multi-core system forwarding of 64 byte packets is worse
much worse: recycling = 24% forwarded vs no recycling = 42% forwarded
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't reference the list element in hardware transmit ring on transmit
completion. The list element is updated by hardware, therefore
it causes a cache miss. Do book keeping in software structure.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate and size transmit ring based on parameters. Saves excess
space and allows configuring larger rings for testing.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for list element error (which should only happen on hardware
errors) should be cleaner and safer. Gets rid of unused ring_size
argument, which makes next patch easier.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch saves elements on transmit ring by only updating the upper
64 bit address when it changes. With many workloads skb's are located
in same region, so it saves space.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the existing macros to show where DMA address is being broken
apart. This is cosmetic only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
yellowfin_init_ring() needs to clean up if dev_alloc_skb() fails and
should pass an error status up to the caller. This also prevents an
buffer underrun if failure occurred in the first iteration.
yellowfin_open() which calls yellowfin_init_ring() should free its
requested irq upon failure.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_mac_addr_set() currently is broken when netif_running() is false.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 111b9dc5 ("e1000e: add aer support") introduces pcie aer
support for e1000e, but it is not reasonable to disable it in
e1000_remove but enable it in e1000_resume. This patch enables aer
support in e1000_probe.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With manageability (Intel AMT) enabled via BIOS, PHY wakeup does not get
configured on newer parts which use PHY wakeup vs. MAC wakeup which causes
WoL to not work. The driver should configure PHY wakeup whether or not
manageability is enabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slow path ulp_init and ulp_exit calls to the bnx2i driver
are sleepable calls and therefore should not be protected using
rcu_read_lock. Fix it by using mutex and refcount during these
calls. cnic_unregister_driver() will now wait for the refcount
to go to zero before completing the call.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slow path ulp_start and ulp_stop calls to the bnx2i driver
are sleepable calls and therefore should not be protected using
rcu_read_lock. Fix it by using mutex and setting a bit during
these calls. cnic_unregister_device() will now wait for the bit
to clear before completing the call.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slow path calls to the cnic driver are sleepable calls so we
cannot use rcu_read_lock(). Use mutex for these slow path calls
instead.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register and unregister with bnx2 during NETDEV_UP and NETDEV_DOWN
events. This simplifies the sequence of events and allows locking
fixes in the next patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the cnic driver tries to grab a symbol from bnx2 when bnx2 is
running init code, symbol_get() will succeed but symbol_put_addr()
will hit BUG() a moment later. module_text_address() fails because
bnx2 is still in init code.
This is fixed by using symbol_put() instead which does the exact
opposite of symbol_get().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new definition to 'pegasus.h' for support Japanese IO DATA
"ETX-US2" USB Ethernet Adapter.
PEGASUS_DEV( $B!H(BIO DATA USB ETX-US2$B!I(B, VENDOR_IODATA, 0x092a,
DEFAULT_GPIO_RESET | PEGASUS_II )
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb(). The use of spin_lock_irq() and spin_unlock_irq()
in the NETPOLL API callbacks causes the interrupts to get enabled and
can lead to kernel instability.
The solution is to use spin_lock_irqsave() and spin_unlock_restore()
to prevent the irqs from getting enabled while in netpoll_send_skb().
Call trace:
netpoll_send_skb()
{
-> local_irq_save(flags)
---> dev->ndo_start_xmit(skb, dev)
---> spin_lock_irq()
---> spin_unlock_irq() *******here would enable the interrupt.
...
-> local_irq_restore(flags)
}
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole restarting flag was introduced by Mike McCormack
and was a temporary duct tape patch around issues with transmits
inflight during restart. The problems it was covering are now
fixed and the code should have been reverted.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test whether VELOCITY_DUPLEX_FULL bit is set in mii_status.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable netdev feature flag bit NETIF_F_FCOE_MTU for 82599 devices and enable
jumbo frame correspondingly when NETIF_F_FCOE_MTU is set.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates netdev->vlan_features for NETIF_F_FCOE_CRC and NETIF_F_FSO, so that
FCoE CRC and GSO offloads will get used for FCoE over ixgbe based vlan
interface.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 driver combines auto speed negotiation with automatic negotiation
of pause parameters; but the ethtool interface expects them to be
split. This patch allows autonegotiation to be used for speed, but
manually disable flow control.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transmit completion can safely run lockless against transmit start.
In the normal case, completion is done from NAPI and only looks
at elements that are at the tail of the ring. When doing shutdown
or reset, the transmiter should be completely block by NAPI disable
and blocking of transmit queue.
Based on earlier work by Mike McCormack.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the places that bounce the device (suspend/resume
and restart). And makes the operations have the same semantics
as normal dev_open/dev_stop.
This also avoids setting the multicast addresses twice when
device is brought up.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The suspend and shutdown code plays with shared state. Use consistent
locking, for extra protection.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid any possible problems with accessing PHY registers on shutdown.
This is a purely theoretical issue and is not related to any of the
outstanding bug reports. Since receiver and transmitter are already
shutdown and phy interrupts for this device are already disabled,
there should already be enough protection. Suggested by Mike McCormack.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reseting the tx chain too soon results in invalid tx queue positions
being delivered in the status queue. This also makes sure there's no
overlap between the cleanup done by sky2_tx_clean() and
sky2_tx_done().
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is pure refactoring.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep sky2->tx_prod consistent since int might be examined by
an softirq poll or restart.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also implement get/set BB mult, get/set TX gain, set RX gain,
disable/restore CRS, run/stop DDFS, RX IQ est and QDIV roundup
in the process.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ath9k_stop() where the HW
was not put into FULL_SLEEP state. Not doing so will
cause issues in suspend-resume and the HW will not respond
to chip resets.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where the device was enabled
before restoring the PCI state.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diversity_control and antenna_switch_swap are already
present in ath9k_ops_config. Remove duplicate occurrences
in ath_hw.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY counters are available in all chipsets supported
by ath9k. Remove the check.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports the AR9002 family of chipsets. This includes
the AR9285 and the miniPCI AR9223 and AR9220 (which themselves
have AR9280+AR5133).
We now refer people to the wiki page as it seems this is not
as popular as we would have hoped.
Reported-by: JD <jd1008@gmail.com>
Cc: Dakota Lee <Dakota.Lee@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This matches ath9k, providing consistency when reading both drivers.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that its shared we can remove ath5k's own implementation.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turns out ath5k and ath9k can share the same helper to
allocates RX skbs. We allocate skbs aligned to the cache line
size. This requirement seems to have come from AR5210; when
this was not done it seems sometimes we'd get bogus data. I'm
also told it may have been a performance enhancement
consideration. In the end I can't be sure we can remove this
on new hardware so just keep this and start sharing it through
ath.ko.
Make ath9k start using this, ath5k is next.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reported that IRQ_MASK conflicts with include/pcmcia/cs.h on
compat-wireless. Remove that and a bunch of other unused defines
from wl1251_reg.h.
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "wl1251: remove wl1251_ops" originally removed file wl1251_ops.c,
but while I rebased the patch the removal got lost. Now remote the file
for real.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "iwlwifi: Traffic type and counter for debugFs" broke iwl3945 in
a case when CONFIG_IWLWIFI_LEDS is disabled:
drivers/net/wireless/iwlwifi/iwl-3945.c:580: error: 'hdr' undeclared (first use in this function)
Fix it by removing the ifdef check for hdr variable.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make it possible to write individual gain table entries.
Allow gain table entries to be written outside gain table init.
Add version-agnostic helpers for writing gain tables.
Use the new TX gain table helpers during table init.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add rx queue pausing to usbnet. This is needed by rndis_wlan so that it can
control rx queue and prevent received packets from being send forward before
rndis_wlan receives and handles 'media connect'-indication. Without this
establishing WPA connections is hard and fail often.
[v2] - removed unneeded use of skb_clone
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the new variables in b43_phy_lp appear to be dead code in
the vendor driver; they will be removed if they remain unused when
LP-PHY implementation is finished.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices created by the libertas driver are currently called eth%d. Which
is wrong, because the device does not at all have anything to do with
Ethernet. And it is also confusing when used on devices with more than
one network device.
Fix this by calling it wlan%d.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were a few warnings when compiling the wl1271 driver on 64 bit
architectures. This was due to size mismatch of integers.
This commit fixes the following warnings:
drivers/net/wireless/wl12xx/wl1271_main.c: In function 'wl1271_irq_work':
drivers/net/wireless/wl12xx/wl1271_main.c:184: warning: large integer implicitly truncated to unsigned type
drivers/net/wireless/wl12xx/wl1271_boot.c: In function 'wl1271_boot_upload_firmware_chunk':
drivers/net/wireless/wl12xx/wl1271_boot.c:103: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'
drivers/net/wireless/wl12xx/wl1271_boot.c:150: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'
drivers/net/wireless/wl12xx/wl1271_boot.c: In function 'wl1271_boot_enable_interrupts':
drivers/net/wireless/wl12xx/wl1271_boot.c:278: warning: large integer implicitly truncated to unsigned type
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I completely missed the "one's complement" instruction from the specs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rev2+ BB init spec has changed behind us, and thus the code is
no longer up to date. Update the code to match the current specs.
Also implement save/restore dig filt state, as required by the
new specification.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement LP-PHY baseband table init for all revisions.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Get rid of calibration timer, instead use a software interrupt
to schedule the calibration tasklet.
a) We don't need a timer for this, there is no need for accuracy
even with round_jiffies i think this is a waste of resources.
Also we don't need to run calibration if we are idle (no
interrupts).
b) When we add ANI support we 'll just extend the poll function
and calibration tasklet and handle all periodic phy calibration
on one place (much cleaner).
c) Having calibration on a tasklet is better since during calibration
we can't transmit or receive (antennas are detached to measure
noise floor), previously calibration could run in parallel with
tx/rx and interfere (packet loss).
v2: kill tasklet on stop_hw, stop/wake queues
v3: use time_is_before_eq_jiffies to compare timestamp with current
time
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* During attach preserve pcicfg bits when enabling pci core
sw retry fix.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Don't put chip to full sleep because there are problems during
wakeup. Instead hold MAC/Baseband on warm reset state via a new
function ath5k_hw_on_hold.
* Minor cleanups
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Tested-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Set correct xpd curve indices for high/low gain curves during
rfbuffer setup on RF5112B with both calibration curves available.
* Don't return zero min power when we have the same pcdac value
twice because it breaks interpolation. Instead return the right
x barrier as we do when we have equal power levels for 2 different
pcdac values.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Read PCI-E infos offset from EEPROM and if it points to
serdes section (0x40), enable serdes programming (further tweaking
of serdes values during attach). This follows Legacy and Sam's
HAL sources.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When beacon is being updated to refresh TIM (AP mode), beacon frames are
de-synchronizing (i.e. two neighbor beacon frames - before and after
update - are being transmitted with a wrong time interval).
That is because xxx_write_beacon should disable beacon generation only
while beacon data are being uploaded to the device, but it should not
disable the beacon clock.
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The v2+ radio init (B2063) is now complete, modulo BCM4325 support.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the the patch:
ath9k: use new FIF_PSPOLL configure filter
I forgot to add the new FIF_PSPOLL to the supported mask.
Without this we mask out the FIF_PSPOLL flag therefore
we'd ignore it from mac80211.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements FIF_PSPOLL filter flag support in rt2x00 drivers,
which has been introduced in mac80211 (see
http://marc.info/?l=linux-wireless&m=124897986330807&w=2).
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch "Implement set_tim callback for all drivers" can cause kernel
oops in rt73usb_write_beacon. The oops is caused by one of the following
race conditions:
* In case of two near calls to set_tim: rt2x00lib_beacondone_iter is
cleaning the beacon skb, whereas rt73usb_write_beacon is still using it.
* In case of two near updates of beacon: first as the result of set_tim
and second as the result of a call from an application (e.g. hostapd).
This patch fixes the race condition by rearranging the update logic and
guarding rt2x00_intf->beacon->skb with a mutex.
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Small changes in signal level was not detected up by the
MOVING_AVERAGE() due to a rounding error, using 'int' type.
rt2x00lib_antenna_diversity_eval:
rssi: -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62
rssi_avg: -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57
The signal level reported back could be significantly (5dBm)
different from the actual value. A level +3dBm is the same as
double the AP output power.
Signed-off-by: Lars Ericsson <Lars_Ericsson@telia.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Antanna quality statistics is not handled correctly, which leads to
software diversity being shutdown completly.
The main problem is that during antenna diversity statistics can
be reset resulting in loosing the signal strength just before
evaluation.
rssi history is not updated correctly leading to incorrect comparison
material for basing antenna switching on.
Signed-off-by: Lars Ericsson <Lars_Ericsson@telia.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware require the ieee80211 header to be aligned to a
4-byte boundary before mapping it to the DMA. Otherwise some
frames (like beacons) will not be send out correctly by the
device.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the IEEE80211_TX_CTL_MORE_FRAMES flag to help determining
if the DMA queue should be kicked. At the moment this is combined
with the ieee80211_has_morefrags() but we might remove that later.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the config() callback function the fields radio_enabled and
the change flag IEEE80211_CONF_CHANGE_RADIO_ENABLED have been
deprecated. This removes the usage of those fields by improving
antenna change detection in the antenna configuration function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Elsewhere, the tqi_type field is compared to constants having a name
beginning with AR5K_TX_QUEUE, rather than AR5K_TX_QUEUE_ID. I have thus
converted AR5K_TX_QUEUE_ID_CAB to AR5K_TX_QUEUE_CAB. This does, however,
change the value, so perhaps something else was wanted.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Depending on required latency requested by pm_qos (via mac80211)
we can automatically adjust the sleep state. Also, mac80211 has
a user-visible dynamic sleep feature where we are supposed to
stay awake after sending/receiving frames to better receive
response frames to our packets, this can be integrated into the
sleep command.
Currently, and this patch doesn't change that yet, we default
to using sleep level 1 if PS is enabled. With a module parameter
to iwlcore, automatic adjustment to changing network latency
requirements can be enabled -- this isn't yet the default due
to requiring more testing.
The goal is to enable automatic adjustment and then go into the
deepest possible sleep state possible depending on the networking
latency requirements.
This patch does, however, enable IEEE80211_HW_SUPPORTS_DYNAMIC_PS
to avoid the double-timer (one in software and one in the device)
when transmitting -- the exact timeout may be ignored but that is
not of big concern.
Note also that we keep the hard-coded power indices around for
thermal throttling -- the specification of that calls for using
the specified power levels. Those can also be selected in debugfs
to allow easier testing of such parameters.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not send CT KILL config command twice and correct critical
temperature informatiom in dmesg
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When compiling without CONFIG_IWLWIFI_DEBUGFS there is a missing
iwl_update_stats symbol. This is fixed by making this function an inline in
the case when CONFIG_IWLWIFI_DEBUGFS is not set due to the hot path in
which it is used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the thermal throttle data structures and code
are really very intermingled with the sleep (power)
control code. They really do belong together in a way
since the thermal throttle code uses powersaving to
achieve its goal, but it's making it hard to work on
the powersave code. Split this up to make that easier.
I've also changed the antenna defines to an enum and
used the same enum for RX and TX.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify the power update function, when driver fail to set the power, it
should not continue move forward and try to change the rx chain
configuration.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For legacy thermal throttling, set the new Thermal Throttling
state and change power index when thermal throttling manager detects
temperature changed. The current implementation sets the state to the
previous Thermal Throttling state, which causes system to enter wrong
power index. The worse case, it will trying to set the
lower power index when device reach critical temperature, it will cuase
issue for both system and the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all the thermal throttling functions to background task to make
sure do not change power and rx chain in interrupt handler.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit "iwlwifi: uCode Alive notification with timeout" introduced a more
reliable mechanism for ucode loading. Unfortunately we hit a problem with
it frequently enough to make a 4965 unusable. The problem can be seen in
debug log below. What this code attempts is to set runtime ucode up to
load, start a timer to wait for the alive response from runtime ucode, and
if it times out it tries again. As can be seen below we receive the alive
response and wake the waiting task _before_ the tasks starts waiting. The
task thus times out as the alive response is not received while it is
waiting for it and it restarts the device. This starts the cycle all over
again.
[29739.000819] ieee80211 phy0: U iwl_mac_start enter
[29739.005751] ieee80211 phy0: U iwl_prepare_card_hw iwl_prepare_card_hw enter
[29739.012798] ieee80211 phy0: U iwl_set_hw_ready hardware ready
[29739.057200] ieee80211 phy0: U iwl4965_load_bsm Begin load bsm
[29739.063366] ieee80211 phy0: U iwl4965_verify_bsm Begin verify bsm
[29739.072485] ieee80211 phy0: U iwl4965_verify_bsm BSM bootstrap uCode image OK
[29739.079671] ieee80211 phy0: U iwl4965_load_bsm BSM write complete, poll 0 iterations
[29739.257019] ieee80211 phy0: I iwl_rx_reply_alive Alive ucode status 0x00000001 revision 0x1 0x9
[29739.260964] ieee80211 phy0: I iwl_rx_reply_alive Initialization Alive received.
[29739.260964] ieee80211 phy0: U __iwl_up iwlagn is coming up
[29739.278571] ieee80211 phy0: U iwl_mac_start Start UP work done.
[29739.284509] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 788
[29739.292432] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 10312
[29739.302004] ieee80211 phy0: U iwl_verify_ucode Initialize uCode is good in inst SRAM
[29739.309746] ieee80211 phy0: U iwl4965_hw_get_temperature Running temperature calibration
[29739.317833] ieee80211 phy0: U iwl4965_hw_get_temperature Calib values R[1-3]: -36 13522 -13496 R4: -2726
[29739.327337] ieee80211 phy0: U iwl4965_hw_get_temperature Calibrated temperature: 310K, 37C
[29739.335598] ieee80211 phy0: U iwl4965_init_alive_start Initialization Alive received.
[29739.343477] ieee80211 phy0: U iwl4965_set_ucode_ptrs Runtime uCode pointers are set.
[29739.351283] ieee80211 phy0: I iwl_rx_reply_alive Alive ucode status 0x00000001 revision 0x1 0x0
[29739.355210] ieee80211 phy0: I iwl_rx_reply_alive Runtime Alive received.
[29739.366731] iwlagn 0000:03:00.0: Runtime uCode already alive? Waiting for alive anyway
[29743.284110] iwlagn 0000:03:00.0: START_ALIVE timeout after 4000ms.
[29743.290337] ieee80211 phy0: U iwl_mac_add_interface enter: type 2
[29744.364089] iwlagn 0000:03:00.0: Runtime timeout after 5000ms
[29744.370882] ieee80211 phy0: U iwl_alive_start Runtime Alive received.
[29744.377347] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 788
[29744.385287] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 10312
[29744.393397] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 94720
[29744.415835] ieee80211 phy0: U iwl_verify_ucode Runtime uCode is good in inst SRAM
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Display sensitivity and chain noise data to help understand the current
environment and RF condition.
The data is feeded by statistics notification and Beacon from uCode;
then used by sensitivity calibration and chain noise calibration to
determine how DSP should react to the environment changes
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Display statistics notification information
The information break down into
uCode_tx_stats
uCode_rx_stats
uCode_general_stats
and can be found in /sys/kernel/debug/ieee80211/phy0/iwlagn/debug
directory
The statistic information display in debugFs is based on the last
statistics notification from uCode; it might not reflect the current
uCode activity. Using "watch" command to monitor the uCode
activity should give up-to-date statistics provided by uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding debugfs function to show current TxFifo/RxFifo read/write
pointer, plus the current tx queue status (wake/stop) for both real and
virtual queue.
This is part of debug feature set to help debugging driver/uCode.
use tx_queue and rx_queue in
/sys/kernel/debug/ieee80211/phy0/iwlagn/debug directory to show the
current read/write pointer for both TxFifo and RxFifo queue
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Break down the traffic type and counter for both Tx and Rx.
Enhance the tx_statistics and rx_statistics debugfs function and move
to /sys/kernel/debug/ieee80211/phy0/iwlagn/debug directory to help
better debugging both driver and uCode related problems.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The traffic buffer will only beallocated and used if either bit 23
(IWL_DX_TX) or bit 24 (IWL_DL_RX) of "debug" is set;
example: "debug=0x800000" - log tx data traffic
"debug=0x1000000" - log rx data traffic
"debug=0x1800000" - log both tx and rx traffic
The traffic log will store the beginning portion (64 bytes) of the
latest 256 of tx and rx packets in the round-robbin buffer for
debugging,
user can examine the log through debugfs file.
How to display the current logged tx/rx traffic and txfifo and rxfifo
read/write point:
"cat traffic_log" in /sys/kernel/debug/ieee80211/phy0/iwlagn/debug
directory
By echo "0" to traffic_log file will empty the traffic log buffer and
reset both tx and rx taffic log index to 0.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename "fat" to "ht40"
The term "fat channel" is deprecated in favor of "HT40"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "iwlwifi: make debug level more user friendly" cleaned up the
debug level handling. In doing so it created a single global debug
level for all devices. Some setups do consits of more that one iwlwifi
device and in these setups there is a requirement that debug levels
should be unique per device.
We now re-introduce the per device debugging while maintaining the
cleanup effort of the previous patch.
The maintain the global debug level and now introduce a per-device debug
level that will be used if it (the per-device debug level) is set. The
per-device debug level can be controlled via the debug_level sysfs file
while the global debug level is controlled by the debug module parameter.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements a basic rfkill support for p54 hardware and
removes a rfkill related WARNING:
fwio.c: In function ‘p54_setup_mac’:
fwio.c:323: warning: ‘radio_enabled’ is deprecated.
by abandoning radio_enable in flavour for IEEE80211_CONF_CHANGE_IDLE.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a coding error which allowed the to upper-layer to
corrupt limited portions of the phy data.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the hardware encryption keys index and array size handling.
Thanks to Gregor Kowski for reporting this issue.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 9cef8737 "mac80211: fix managed mode BSSID handling" broke
association in wl1251, most probably because the driver configured
the bssid filter incorrectly. Workaround this by disabling filter
altogether. This needs to be fixed properly soon.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The logs currently don't show when hw scan has completed, fix that.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano is maintaining wl1271 part.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that wl1271 doesn't use reg.h anymore, it can be renamed to
wl1251_reg.h.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 should use workqueue created by mac80211 to not block the events
workqueue too long.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It should not be hidden inside wl1251_cmd_ps_mode().
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a bug in wl1251_op_config(). It was calling join with previous
channel. Fix it by setting assigning wl->channel before calling join command.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Better to use wl1251_cmd_join() only for sending the command and move
the logic to wl1251_join().
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because join channel tunes to a channel, better to make it more obvious
by adding a parameter for it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because wl->channel was initialised to one, the first join command in
wl1251_op_config() always failed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should wait everytime for the join command to finish, not waiting for
it might create problems.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 was using hardcoded beacon intervals and dtim periods, use the ones
provided by mac80211 instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's more common to have beacon interval before dtim period. Also use
bool instead of u8.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now wl1271 is splitted to separate files, no need to use wl1251_ops anymore.
So remove struct wl1251_chip and wl1251_ops.c.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the wl1251_sdio module, enabling the SDIO interface for
wl1251, as used by the Google G1 phone and others.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This creates a module called wl1251_spi.ko which contains just the
SPI-specific code. The core remains in the module wl1251.ko.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change moves all of the spi specific code from main.c into
spi.c. The module initialization code also moves, but common
code for initializing mac80211 etc. stays in main.c, as this will
eventually form a common library module also used by wl1251_sdio.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The same partition setting code can be used for both SPI and SDIO
modes, if we remove the spi-specific commands and use the more
generic buffer write routines. Do that and move it to io.c
since it deals with register/memory address offsets.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce an ops struct with read, write, and reset functions to
abstract away the details of the wl1251 bus interface. Doing this
will allow SDIO to coexist with SPI by supplying its own I/O
routines.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove a dependency on the bus-specific struct device by using wiphy_dev
when requesting firmware.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to eventually support wl1251 spi and sdio interfaces, move
the register and memory transfer functions to a common file. Also
rename wl1251_spi_mem_{read,write} to indicate its common usage.
We still use spi_read internally until SDIO interface is introduced
so nothing functional should change here.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fixed addresses are not used in wl1251, only in wl1271. So it can
be safely removed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI uses the beacon RSSI for its operation.
Update this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmask can be obtained directly from ath_hw.
Also, use a helper macro for comparing CTLs - this improves readability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Write CCK power-per-rate array always and report
correct TX power to regulatory.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps the antenna configuration mechanism
for 4K chips.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A subsequent patch would use these for configuring
antennae on AR9285.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
regChainOffset is always zero, remove it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add eeprom_def.c, eeprom_4k.c and eeprom_9287.c
This improves maintainability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the wl1271 driver in the Kconfig and in the
Makefile.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver supports the wl1271 chipset from Texas Instruments based on the
WiLink(tm) 6.0 mobile platform. Support for wl1273 should be relatively easy
to add. This chipset is designed for embedded devices, with good powersaving
capabilities. The wl1271 chipset is the successor of wl1251 and supports the
802.11b/g/n standards, but currently this driver supports only b/g.
More information about this chipset can be found here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12762&contentId=29993
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TKIP support was added, we stored the keys separately to avoid
issues when both TKIP and WEP keys are sent to the driver.
We need to consolidate the storage to convert to cfg80211, so do this
first and try iron out the issues.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will need this from the cfg80211 disassociate call.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows the disassociation to be called via cfg80211.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we store the keys for cfg80211, the sequence lengths will also be
stored. So avoid assuming the sequence lengths at this level.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps in the refactorring required to convert the driver to
cfg80211.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a boolean value set based on firmware capabilities, so move the
variable to the capabilities section and reduce the structure size.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update a comment that still says IEEE80211_IF_TYPE instead of NL80211_IFTYPE.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tkip hw support uncovered a bug in b43_write_probe_resp_template : it is
writing at the wrong shm offset, it is in the B43_SHM_SH_TKIPTSCTTAK
zone. Remove b43_write_probe_resp_template, b43_write_probe_resp_plcp
and b43_write_probe_resp_plcp because the probe response offload is
currently not supported by mac80211.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of HostFlags defines in the LP-PHY code.
Fix fallout from the IEEE80211_IF_TYPE to NL80211_IFTYPE change.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add B2063 radio init code and tables for LP-PHY.
Rename structures common between B2062 and B2063 to B206X.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw uses its own LED stuff so let rename its LED
stuff as such.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We used to set pspoll filter on ath9k on AP mode but
we no longer need this mode specific check as mac80211
now does the check for us and informs us when we should
enable pspoll through FIF_PSPOLL.
Cc: Igor Perminov <igor.perminov@inbox.ru>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
