[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML Initialization was previously done on dcn21_resource initialization.
This meant that DML soc struct was populated with hardcoded values.
[How]
Move DML initialization to after updating bounding box, to use clock table
values from SMU.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PHY will sometimes be in bad state on hotplugging display from USB-C
dongle.
[How]
Add additional calls to disable and then enable PHY before link training
starts during verify_link_cap.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recent double buffering changes for dcn2 use IX_REG_READ.
However, this macro returns the full register value, with the need to
manually shift and mask it to retrieve field data.
[How]
Create new IX_REG_GET macro that handles shift and mask.
Use this for double buffering reads instead of IX_REG_READ.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting video brightness, screen tearing was observed.
This was due to overwritten values in ICSC registers. In dcn10, this issue had been
fixed by implementing double buffering via alternating ICSC modes.
However, the second register set used in dcn1 doesn't exist in dcn2.
[How]
Create new program_input_csc for dcn20.
Use ICSC_B registers instead of COMA registers as second set.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting colour properties (e.g. brightness), screen tearing was observed.
This was due to overwritten values in OCSC registers. In dcn10, this issue had been fixed by
implementing double buffering by alternating OCSC modes.
[How]
Alternate which OCSC registers are used by switching modes each time.
This double buffers the CSC writes.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously update_bw_bounding_box for RN was commented out
due to incorrect values causing BSOD on Hybrid Graphics.
However, commenting out this function also may cause issues
such as underflow in certain cases such as 2x4K displays.
[How]
Fix dram_speed_mts calculations.
Update from proper index of clock_limits[]
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, pipe resources are assigned to an index that matches the pipe position.
However, if pipe 1 or 2 is disabled, there will be a gap in the arrays which causes a crash when iterating based on pipe_count.
[How]
Fix resource construct to assign resources to minimum available array index.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The earlier change: "check phy dpalt lane count config"
uses link encoder registers not defined properly.
That caused regression with mst-enabled display not
lighting up.
[How]
Add missing reg definitions.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Introduce DC_FP_START()/DC_FP_END() macros to help enable floating
point kernel mode support across various architectures.
v2: move copyright update to commit which adds the changes
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling kzalloc() and related functions requires the
linux/slab.h header to be included:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c: In function 'dcn21_ipp_create':
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c:679:3: error: implicit declaration of function 'kzalloc'; did you mean 'd_alloc'? [-Werror=implicit-function-declaration]
kzalloc(sizeof(struct dcn10_ipp), GFP_KERNEL);
A lot of other headers also miss a direct include in this file,
but this is the only one that causes a problem for now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Value obtained from DV is not allowing 8k60 CTA mode with DSC to
pass, after checking real value being used in hw, find out that
correct value is 3600, which will allow that mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pstate_latency_us never gets updated from the hard coded value
in rn_clk_mgr.c
[how]
update the wm table's values before we do calculations with them
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers.
[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is becoming increasingly hard to figure out which
function is called on the different DCN versions
[How]
1. Make function pointer table init in its own init.c file
2. Remove other scenarios in hwseq.c file that need to
include headers of other DCN versions. (If needed,
it should have been done via the function pointers)
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Too many construct functions which makes searching
difficult, especially on some debuggers.
[How]
Append all construct and destruct functions with dcn
number and object type to make each construct function
name unique
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN21 is stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup Renoir definitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN21 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN2 and DSC are stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup NV defninitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN2 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* dce/dce_dmcu.c: dcn20_*lock_phy()
* dce/dce_dmcu.c: dcn20_funcs
* dce/dce_dmcu.c: dcn20_dmcu_create()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For unknown reason, immediate flip with host VM translation on NV12
surface will underflow on last row of PTE.
[How]
Hack chroma viewport height to make fetch one more row of PTE.
Note that this will cause hubp underflow on all video underlay
cases, but the underflow is not user visible since it is in
blank region.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Support for DMUB only depends on support for DC. It doesn't use floating
point so we don't need to guard it by any specific DCN revision.
[How]
Drop the guards and cleanup the newlines around each one.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC will use DMUB for command submission and flow control during
initialization.
Register offloading as well as submitting some BIOS commands are part
of the DC internal interface but are guarded behind debug options.
It won't be functional in amdgpu_dm yet since we don't pass the
DMUB service to DC for use.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The interface to the DMCUB won't be through DC itself. DC will instead
call into the DMUB interface introduced with a future change.
The CONFIG_DRM_AMD_DC_DMUB defines will still be used for now but will
be dropped at the end of the series.
Since this define was never configurable in the first place this code
wasn't used.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In Hybrid Graphics, dcn2_1_soc struct stays alive through PnP.
This causes an issue on dc init where dcn2_1_soc which has been
updated by update_bw_bounding_box gets put into dml->soc.
As update_bw_bounding_box is currently incorrect for dcn2.1,
this makes dml calculations fail due to incorrect parameters,
leading to a crash on PnP.
[How]
Comment out update_bw_bounding_box call for now.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The enum value for TRANSMITTER_UNIPHY_G is 9. In resource dc_xx_resource
file structure link_enc_regs[], the TRANSMITTER_UNIPHY_G registers are
initialized at index 6. Due to this mismatch, if monitor is attached to
port using TRANSMITTER_UNIPHY_G then the monitor blanks out.
[How]
add function map_transmitter_id_to_phy_instance() and use the function
to map enum transmitter to link regs.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DML is incorrectly initialized with 4 pipes on 3 pipe configs
RequiredDPPCLK is halved on unsplit pipe due to an incorrectly handled 3 pipe
case, causing underflow with 2 planes & pipe split (MPO, 8K + 2nd display)
[HOW]
Set correct number of DPP/OTGs for dml init to generate correct DPP topology
Double RequiredDPPCLK after clock is halved for pipe split
and find_secondary_pipe fails to fix underflow
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously only dummy functions were added in Diags for FPGA.
On silicon, this would lead to a segmentation fault on silicon diags.
[How]
Check if diags silicon and if so, add dummy functions.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN20 and DCN21 have different phy programming sequences.
[How]
Create a separate dcn21_link_encoder for Renoir
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1-add configurable timeout support to aux engine.
2-add timeout support field to dc_caps
3-add reg_key to override extended timeout support
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1-add timeout length and multiplier fields to aux_control1 register
2-update access mechanism from macro constructed name to uint32_t
defined addresses.
3-define registers and field per asic family
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Doing this allows us to split it for diffrent asics. This design will
be helpful for future Asciis.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously SMU was giving us 0s for the clock table. Now they have valid
clock table. We should use theirs. Also, need to send SMU watermark
ranges for selecting optimal watermarks.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The SMU message to enable this feature looks at argument. Previous code
didn't send right argument. This change will allow the feature to be
be enabled.
[How]
Fixed one issue where SMU message to enable the feature was sent without
setting the parameter.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
