When a 50610 or 50610M is paired against particular remote partners,
link is slow to come up. This patch works around the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates the code that requires the SMDSP clock to be
enabled into a single function that (hopefully) makes the dependency
obvious.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the loopback test timeout from 250 usec to 350 usec.
When the 5785 is paired against an AC131 phy, the older timeout is
just a little too close to the expected performance based on timings.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the port mode to MII when the link is down for the 5785.
Setting the port mode to MII instead of GMII saves power.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AC131 does not respect the power down bit (bit 11) of the MII
Control Register (reg 0x0). Instead, software is required to put the
phy into standby power down mode through the shadow register set. This
patch implements support for the AC131 standby power down mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves 5785 performance by allowing the write DMA engine to
request larger DMA burst sizes than it otherwise would.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to check the status of pci_map_single() before
allowing rx buffers to be used. It also converts the pci_map_single()
call in tg3_run_loopback() to use skb_dma_map() instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prevents a PCIe tx glitch by allowing the transmitter to go
to a low power state.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the PHY_ADDR preprocessor definition. The following
patch will identify a new member on the MDIO bus, so we want this
preprocessor definition to be a little more descriptive.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain power saving conditions, 57780 asic rev devices might
disappear from the system. The fix is to disallow the PCIe PLL from
powering down.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5906 has trouble with fragments that are less than 8 bytes in size.
This patch works around the problem by pivoting the 5906's transmit
routine to tg3_start_xmit_dma_bug() and introducing a new SHORT_DMA_BUG
flag that enables code to detect and react to the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a flag for each bug workaround in
tg3_start_xmit_dma_bug(). This is prep work for the following patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change name on vlan_rx_add, kill, register to match other driver API.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_get_by_name_rcu() instead of dev_get_by_name(),
to avoid touching device refcount in hotpath.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add API Add k8695_get_rx_enable_bit() for get Rx interrupt
enable/status bit.
2. add some comment or document about some functions and variables.
3. update driver version to "1.02"
4. add napi_enable() and napi_disable() in open/close file method.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Don't call rtnl_link_unregister if rtnl_link_register fails
- Set .priv_size so we aren't stomping on uninitialized memory
when we use netdev_priv, on bond devices created with
ip link add type bond.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a basic set of rtnl link ops and takes advantage of
the fact that rtnl_link_unregister kills all of the surviving
devices to all us to kill bond_free_all. A module alias
is added so ip link add can pull in the bonding module.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manually inline the code from bond_deinit to bond_uninit. bond_uninit
is the only caller and it is short.
Move the call of bond_release_all from the netdev notifier into
bond_uninit. The call site is effectively the same and performing
the call explicitly allows all the paths for destroying a
bonding device to behave the same way.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop calling dev_get_by_name to see if the bond device already
exists. register_netdevice already does that.
Stop calling bond_deinit if register_netdevice fails as bond_uninit
is guaranteed to be called if bond_init succeeds.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch delegates the work of creating the sysfs groups
to the netdev layer and ultimately to the device layer. This
closes races between uevents.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 23289a37e2
(net: add a list_head parameter to dellink() method),
I forgot to actually use this parameter in veth_dellink.
I remember feeling a bit uncomfortable about veth_close(),
because it does :
netif_carrier_off(dev);
netif_carrier_off(priv->peer);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For USB 3.0 it is necessary that all drivers use the standard
API to reset a configuration. This removes a home-grown
implementation.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Hi David,
please take this for the next merge window.
Regards
Oliver
Signed-off-by: David S. Miller <davem@davemloft.net>
Tentative support for newer Marvell hardware including
the Yukon-2 Optima chip. Do not have hatdware to test this yet,
code is based on vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes related to support of Yukon supreme chip.
Don't have this chip version to test on,
these are reverse engineered from the vendor (GPL) driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Program the receive pause thresholds differently depending on
chip version. This cloned from from the vendor (GPL) driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds infrastructure for the newer chip versions and workarounds.
Extracted from the vendor (GPL) driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new ID that just showed up in latest vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can tell whether GRO is being applied, this heuristic is
effective once more.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When GRO is successfully merging received packets, we should allocate
raw page buffers rather than skbs that will be discarded by GRO.
Otherwise, we should allocate skbs.
GRO also benefits from higher interrupt moderation, so increase the
score for mergeable RX packets.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables are unsigned so the `< 0' test always fails, the
other part of the test catches wrapped values.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the sequence of strcmp calls for interpreting ZSAU parameter
strings by a table of known strings and lookup loop to improve
readability.
Impact: readability improvement, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
On more step towards the holy grail of checkpatch.pl silence.
Impact: cosmetic
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the quest for the holy grail of checkpatch.pl silence.
Impact: cosmetic
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duly uglified as demanded by checkpatch.pl.
Impact: cosmetic
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dum sanctis checkpatch.pl'ae legibus obsequimur.
Impact: cosmetic
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorganize the code of the Gigaset M10x driver to make it more
readable, less redundant, better aligned to the style of other
parts of the driver, and cause fewer checkpatch.pl complaints.
Impact: code reorganization, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CAPI interface incorrectly assumed that CAPI messages would always
start at the beginning of the data buffer: fix by treating DATA_B3
messages as the link layer header to their payload data. This fix
changes the way acknowledgement information is propagated through the
hardware specific modules and thereby impacts the ISDN4Linux variant
of the driver, too.
Also some assumptions about methods not being called from interrupt
context turned out to be unwarranted; fix by using dev_kfree_skb_any()
wherever non-interrupt context isn't guaranteed.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
A missing dot lead to garbage characters being included in the
dial command generated from a CAPI CONNECT_REQ message, which
interestingly enough worked anyway, illustrating the resilience
of the device.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the "ignoring Additional Info" warning message by better
readable ones citing the specific subparameters being ignored.
Make parts of the code more readable by using a local cmsg
pointer variable.
Impact: readability improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found that the current version of drivers/net/usb/dm9601.c can be used to
successfully drive a low-power, low-cost network adapter with USB ID
0a46:9000, based on a DM9000E chipset. As no device with this ID is yet
present in the kernel, I have created a patch that adds support for the device
to the dm9601 driver.
Created and tested against linux-2.6.32-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mailbox command process would only process a maximum of 5 unrelated
firmware events while waiting for it's command completion status.
It should process an unlimited number of events while waiting for a maximum of 5 seconds.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up driver resources without touch the hardware. Add pci
save/restore state.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PCI IDs for the next generation chip to the
PCI_DEVICE_ID table.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
