Some Intel controllers (e.g. BXT) might fail to set bus power after a
D3 -> D0 transition due to the present state not yet having propagated.
Retry for up to 2 milliseconds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let devices define their own sdhci_ops so that device-specific variations
can be implemented without adding quirks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Unlike other cases, sdhci_set_power() does not reflect the default
implementation of the ->set_power() callback. Rename it and create
sdhci_set_power() that is the default implementation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Multi-block data transfers can specify the number of blocks either using a
Set Block Count command (CMD23) or by sending a STOP command (CMD12) after
the required number of blocks has transferred. CMD23 is preferred, but some
cards don't support it. CMD12 with R1b response is used for writes, and
R1 response for reads.
Some SDHCI host controllers give a Transfer Complete (TC) interrupt for the
STOP command (CMD12) whether or not a R1b response has been specified. The
quirk SDHCI_QUIRK2_STOP_WITH_TC identifies those host controllers, but the
implementation only considers the case where the TC interrupt arrives at
the same time as the Command Complete (CC) interrupt. However,
occasionally TC arrives before CC. That is harmless, but does generate an
error message "Got data interrupt 0x00000002 even though no data operation
was in progress".
A simpler approach is to force R1b response onto all STOP commands, because
SDHCI will handle TC before CC in the general case, so do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the vendor's requirement, we shouldn't do any setting for
1.8V Signaling Enable, otherwise the interaction/behaviour between
phy and controller will be undefined. Mostly it works fine if we do
that, but we still see failures. Anyway, let's fix it to meet the
vendor's requirement. The error log looks like:
[ 93.405085] mmc1: unexpected status 0x800900 after switch
[ 93.408474] mmc1: switch to bus width 1 failed
[ 93.408482] mmc1: mmc_select_hs200 failed, error -110
[ 93.408492] mmc1: error -110 during resume (card was removed?)
[ 93.408705] PM: resume of devices complete after 213.453 msecs
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes the following sparse warning:
drivers/mmc/host/sdhci-of-arasan.c:253:6: warning:
symbol 'sdhci_arasan_reset' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remvoe the deprecated "supports-highspeed" property.
DWMMC controller will not use this property anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
msize and rx_wmark are properly initialized, we dont't
need to assign them again.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's very prone to make mistake as we might forget
to replace all PAGE_SIZEs with new values if we try
to modify the ring buffer size for whatever reasons.
Let's use a macro to define it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The original log didn't figure out that we could still
finish this transfer by PIO mode even if failing to use
DMA. And it should be kept for debug level instead of
error one.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We could see an obvious race condition by test that
the former write operation by IDMAC aiming to clear
OWN bit reach right after the later configuration of
the same desc, which makes the IDMAC be in SUSPEND
state as the OWN bit was cleared by the asynchronous
write operation of IDMAC. The bug can be very easy
reproduced on RK3288 or similar when we reduce the
running rate of system buses and keep the CPU running
faster. So as two separate masters, IDMAC and cpu
write the same descriptor stored on the same address,
and this should be protected by adding check of OWN
bit before preparing new descriptors.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We intend to add more check for descriptors when
preparing desc. Let's spilt out the separate body
to make the dw_mci_translate_sglist not so lengthy.
After spliting out these two functions, we could
remove dw_mci_translate_sglist and call both of them
when staring idmac.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci controller on xilinx zynq devices will not function unless
the CD bit is provided. http://www.xilinx.com/support/answers/61064.html
In cases where it is impossible to provide the CD bit in hardware,
setting the controller to test mode and then setting inserted to true
will get the controller to function without the CD bit.
When the device has the property xlnx,fails-without-test-cd the driver
changes the controller to test mode and sets test inserted to true to
make the controller function.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to add R1 without CRC support, refactor the bus width routine a
little and extend a quirk check. To support "non-removable;" we need a
workaround which will be hopefully removed when reworking PM soon.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP_CMD_DURING_TFR for Intel BYT and related eMMC host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP_CMD_DURING_TFR for Intel BYT and related eMMC host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now SDHCI supports commands during transfer, enable support for the core
API.
There are 3 small changes needed:
First, auto-CMD12 cannot be used with a cap_cmd_during_tfr request because
the host controller cannot expect the command line to be available.
Secondly, a cap_cmd_during_tfr request must not send a stop command, again
because the host controller cannot expect the command line to be available.
Thirdly, when a cap_cmd_during_tfr command completes, use
mmc_command_complete() to notify the upper layers that the command line is
now available for further commands.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clear incorrect SDHCI_CAN_64BIT capability on Broadcom MIPS based SoCs.
The MIPS based SoCs are using ADMA only, but the several SoCs have the
incorrect capability bit about ADMA 64-bit. The "brcm,bcm7425-sdhci" is
compatible string for MIPS based SoC.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A64 SoC features a MMC controller which need only the mod clock, and can
calibrate delay by itself. This patch adds support for the new MMC
controller IP core.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() returns an error value on failure, not NO_IRQ,
so the error handling here could never work.
This changes the code to propagate the error value instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the TRM, the SD/MMC controller on Tegra124 supports 34-bit
addressing, but testing shows that this doesn't work. On a device which
has more than 2 GiB of RAM and LPAE enabled, buffer allocations can use
addresses above the 32-bit boundary.
One way to work around this would be to enable IOMMU physical to virtual
address translations for the SD/MMC controllers, but that's not easy to
implement without breaking existing use-cases. It's also not obvious why
34-bit addressing doesn't work as advertised. In order to fix this for
existing users, add the SDHCI_QUIRK2_BROKEN_64_BIT_DMA quirk for now.
Reported-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
corecfg_clockmultiplier indicates clock multiplier value of
programmable clock generator which should be the same value
of SDHCI_CAPABILITIES_1. The default value of the register,
corecfg_clockmultiplier, is 0x10. But actually it is a mistake
by designer as our intention was to set it to be zero which
means we don't support programmable clock generator. So we have
to make it to be zero on bootloader which seems work fine until
now. But now we find an issue that when deploying genpd support
for it, the remove callback will trigger the genpd to poweroff the
power domain for sdhci-of-arasan which manage the controller, phy
and corecfg_* stuff.
So when we do bind/unbind the driver, we have already reinit
the controller and phy, but without doing that for corecfg_*.
Regarding to only the corecfg_clockmultipler is wrong, let's
fix it by explicitly marking it to be zero when probing. With
this change, we could do bind/unbind successfully.
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Tested-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel Merrifield provides an interface to an external SD card.
Enable it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel Merrifield is known to have an SDIO interface and on Intel Edison board a
WiFi card is wired to it.
Enable the interface here to allow WiFi card enumeration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor intel_mrfld_mmc_probe_slot() to use switch case. The change allows to
add a support for SD and SDIO interfaces without any pain.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hisilicon Hikey have no tuning function in dw_mmc-k3.c,
so we must do the tuning function stub when we init UHS card.
Signed-off-by: Jin Guojun <kid.jin@hisilicon.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following log we found indicate the fact that dw_mmc
didn't treat EBE or SBE as a similar problem as CRC error.
-EIO is quite not informative as it may indicate that the device
is broken rather than that of tuning stuff.
...
[ 89.057226] bcmsdh_sdmmc: Failed to Read byte F1:@0x1001f=ff, Err: -5
[ 89.058811] bcmsdh_sdmmc: Failed to Read byte F1:@0x1001f=ff, Err: -5
[ 89.059415] bcmsdh_sdmmc: Failed to Read byte F1:@0x1000e=ff, Err: -84
[ 89.254248] dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 199
[ 89.273912] dhd_set_suspend: Remove extra suspend setting
[ 89.274478] dhd_enable_packet_filter: enter, value = 0
64 bytes from 112.90.83.112: icmp_seq=24 ttl=53 time=1321 ms
64 bytes from 112.90.83.112: icmp_seq=25 ttl=53 time=319 ms
64 bytes from 112.90.83.112: icmp_seq=26 ttl=53 time=69.8 ms
64 bytes from 112.90.83.112: icmp_seq=27 ttl=53 time=37.5 ms
...
For the host, when failing to sample cmd's response due to
tuning stuff, we still return -EIO as it's quite vague to figure
out whether it related to signal or just the broken devices, especially
for the card type detection when booting kernel as all things go well
but the cmd set used.
But for the data phase, if receiving the cmd's response which
carriess data transfer, we should have more confidence that it
is very probably related to the tuning stuff.
Just as the log shown above, we sometimes suffer too much
this kind of pain as the dw_mmc return -EIO for the case, so
mmc-core will not do retune and caller drivers like bcm's wifi
driver, still retry the failure more and more until dw_mmc
finally generate CRC.
Adrian suggested that drivers who care the specific cases should
call mmc_retune_needed rather than doing it in mmc core. It makes
sense but I'm considering that -EILSEQ actually means illegal sequence
, so we use it for CRC cases. Meanwhile, SBE/EBE indicate the illegal
sequence of start bit or end bit for data0~7. So I realize that we should
use -EILSEQ for them both as well CRC cases.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dwmmc host controller may in unknown state when entering kernel boot. One
example is when booting from eMMC, bootloader need initialize MMC host
controller into some state so it can read. In order to make sure MMC host
controller in a clean initial state, this reset support is added.
With this patch, a 'resets' property can be added into dw_mmc device
tree node. The hardware logic is: dwmmc host controller IP receives a reset
signal from a 'reset provider' (eg. power management unit). The 'resets'
property points to this reset signal. So, during dwmmc driver probe,
it can use this signal to reset itself.
Refer to [1] for more information.
[1] Documentation/devicetree/bindings/reset/reset.txt
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If ciu/biu clock are NULL, clk_disable_unprepare should be just
returned. In clk_disable_unprepare(), already checked whether clk is
error or NULL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention to remove it comes from the conflict of
what the mmc-core does with the way dw_mmc treats disable-wp.
We could see that 'disable-wp' is supported by core but
it's deprecated by dw_mmc as we don't expect it to be existed
for each slot subnode but should be in the parent node. Based
on searching for all the upstream dts using dw_mmc, we're
confident that none of them use the deprecated way. Maybe
we should take old dtb in consideration but it was a flag day
since the time we was considering to take it away. The fact is
that there are none of dts using the deprecated way since v3.18
or even earlier. So personally I don't believe the old dtb
would/could bootup current kernel(may not?). Let's remove it now.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Chipsets before Exynos5420 did not support HS400 so if MMC core tries to
configure HS400 timing, this might or might not work. Warn in such
cases because this is DTB misconfiguration.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 1ef5e49e46 ("mmc: sdhci-of-esdhc: add/remove some quirks
according to vendor version") moved sdhci-of-esdhc away from using the
->platform_init() callback.
As it was the only user of it and that it seems reasonable to believe that
it won't be needed again, let's just remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
The commit 52ac7acf41 ("mmc: sdhci-pci: Convert to use managed functions
pcim_* and devm_*") converted ->probe() / ->remove() functions to use device
managed resource API. Here is a follow up to cover sdhci_pci_probe_slot() and
sdhci_pci_remove_slot().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Populating card_busy caused a side-effect on a chip variant we don't
have documentation for (r8a73a4). So, enable it and voltage switching
only on devices known to support those features.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 452e5eef6d ("mmc: tmio: Add UHS-I mode support")
card_busy is only used/tested on SDHI for R-Car Gen2 and later.
Move it to the SDHI driver, so we can then activate it conditionally
depending on the SDHI type.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sunxi-mmc driver does not take into account the processor may be big
endian when writing the DMA descriptors. This causes cards not to be
detected when running a big-endian kernel. Change the descriptors for
IDMA to use __le32 and ensure they are suitably swapped before writing.
Tested successfully on the Cubieboard2.
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_round_rate() may return an error. Check it.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PHY intended to be used with the Arasan SDHCI 5.1 controller has trouble
turning on when the card clock is slow or off. Strangely these problems
appear to show up consistently on some boards while other boards work
fine, but on the boards where it shows up the problem reproduces 100% of
the time and is quite consistent in its behavior.
These problems can be fixed by always making sure that we power on the
PHY (and turn on its DLL) when the card clock is faster than about 50
MHz. Once on, we need to make sure that we never power down the PHY /
turn off its DLL until the clock is faster again.
We'll add logic for handling this into the sdhci-of-arasan driver. Note
that right now the only user of a PHY in the sdhci-of-arasan driver is
arasan,sdhci-5.1. It's presumed that all arasan,sdhci-5.1 PHY
implementations need this workaround, so the logic is only contingent on
having a PHY to control. If future Arasan controllers don't have this
problem we can add code to decide if we want this flow or not.
Also note that we check for slow clocks by checking for <= 400 kHz
rather than checking for 50 MHz. This keeps things the most consistent
and also means we can power the PHY on at max speed (where the DLL will
lock fastest). Presumably anyone who intends to run with a card clock
of < 50 MHz and > 400 kHz will be running on a device where this problem
is fixed anyway.
I believe this brings some resolution to the problems reported before.
See the commit 6fc09244d7 ("mmc: sdhci-of-arasan: Revert: Always power
the PHY off/on when clock changes").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wait_event_interruptible_timeout() will return early if the blocked
process receives a signal, causing the driver to abort the tuning
procedure and possibly leaving the controller in a bad state. Since the
tuning command is expected to complete quickly (<50ms) and we've set a
timeout, use wait_event_timeout() instead.
Signed-off-by: Christopher Freeman <cfreeman@nvidia.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
i.MX USDHC Reference Manual has a mistake, for the register SYS_CTRL,
the DTOCV(bit 19~16) means the data timeout counter value. When DTOCV
is set to 0xF, it means SDCLK << 29, not SDCLK << 28.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, when call esdhc_set_timeout() to set the data timeout counter value,
IPP_RST_N(bit 23) is wrongly affected. This patch add a mask to avoid this.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
- if (of_get_property(e1,e2,NULL))
+ if (of_property_read_bool(e1,e2))
S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In clk_set_rate() or clk_prepare_enable() error handling case, the
error return code ret is not set, so sdhci_bcm_kona_probe() return
0 in those error cases.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wait_for_completion_timeout_interruptible returns long not unsigned long
so dma_time, which is used exclusively here, is changed to long.
Fixes: 1b66e94e6b ("mmc: moxart: Add MOXA ART SD/MMC driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It turns out that sun4i (A10) and sun5i (A13 & co) do not have sample
clocks, so add a new sun7i-a20-mmc compatible and do not try to use
sample clocks on sun4i / sun5i.
Since sun4i / sun5i do not have sample clocks, they cannot (reliably) do
DDR rates, so only set MMC_CAP_1_8V_DDR when we do have sample clks.
Note this patch leaves the clk_prepare_enable() / clk_disable_unprepare()
calls to the sample clks as-is, without adding checks for them being
NULL. All the clk_foo calls accept a NULL clk and will return success when
called with a NULL clk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a sunxi_mmc_clk_set_phase() helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Create a struct to hold the various model / compatible string dependend
settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When support for the sample clks was added calls to prepare_enable
were added to the probe path, but matching calls to disable_unprepare
were forgotten in the remove path, this fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When there is no Card which is set to "broken-cd", it's displayed a clock
information continuously. Because it's polling for detecting card.
This patch is fixed this problem.
Fixes: 65257a0dee ("mmc: dw_mmc: remove UBSAN warning in dw_mci_setup_bus()")
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is wrong to use uninitialized dma_slave_config and configure only
certain fields as the DMAengine driver might look at non initialized
(random data) fields and tries to interpret it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is wrong to use uninitialized dma_slave_config and configure only
certain fields as the DMAengine driver might look at non initialized
(random data) fields and tries to interpret it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some ST platforms contain interconnect (ICN) clocks which must be handed
correctly in order to obtain full functionality of a given IP. In this
case, if the ICN clocks are not handled properly by the ST SDHCI driver
MMC will break and the following output can be observed:
[ 13.916949] mmc0: Timeout waiting for hardware interrupt.
[ 13.922349] sdhci: =========== REGISTER DUMP (mmc0)===========
[ 13.928175] sdhci: Sys addr: 0x00000000 | Version: 0x00001002
[ 13.933999] sdhci: Blk size: 0x00007040 | Blk cnt: 0x00000001
[ 13.939825] sdhci: Argument: 0x00fffff0 | Trn mode: 0x00000013
[ 13.945650] sdhci: Present: 0x1fff0206 | Host ctl: 0x00000011
[ 13.951475] sdhci: Power: 0x0000000f | Blk gap: 0x00000080
[ 13.957300] sdhci: Wake-up: 0x00000000 | Clock: 0x00003f07
[ 13.963126] sdhci: Timeout: 0x00000004 | Int stat: 0x00000000
[ 13.968952] sdhci: Int enab: 0x02ff008b | Sig enab: 0x02ff008b
[ 13.974777] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 13.980602] sdhci: Caps: 0x21ed3281 | Caps_1: 0x00000000
[ 13.986428] sdhci: Cmd: 0x0000063a | Max curr: 0x00000000
[ 13.992252] sdhci: Host ctl2: 0x00000000
[ 13.996166] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x7c048200
[ 14.001990] sdhci: ===========================================
[ 14.009802] mmc0: Got data interrupt 0x02000000 even though no data operation was in progress.
A decent point was raised about minimising the use of a local variable that
we 'could' do without. I've chosen consistency over the possibility of
reducing the local variable count by 1. Thinking that it's more important
for the code to be grouped and authoured in a similar manner/style for
greater maintainability/readability.
Cc: stable@vger.kernel.org
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wzSC
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds"
* tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc: (135 commits)
mmc: rtsx_pci: Remove deprecated create_singlethread_workqueue
mmc: rtsx_pci: Enable MMC_CAP_ERASE to allow erase/discard/trim requests
mmc: rtsx_pci: Use the provided busy timeout from the mmc core
mmc: sdhci-pltfm: Drop define for SDHCI_PLTFM_PMOPS
mmc: sdhci-pltfm: Convert to use the SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pltfm: Make sdhci_pltfm_suspend|resume() static
mmc: sdhci-esdhc-imx: Use common sdhci_suspend|resume_host()
mmc: sdhci-esdhc-imx: Assign system PM ops within #ifdef CONFIG_PM_SLEEP
mmc: sdhci-sirf: Remove non needed #ifdef CONFIG_PM* for dev_pm_ops
mmc: sdhci-s3c: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-pxav3: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-of-esdhc: Simplify code by using SIMPLE_DEV_PM_OPS
mmc: sdhci-acpi: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pci-core: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: Change the max discard sectors and erase response when HW busy detect
phy: rockchip-emmc: Wait even longer for the DLL to lock
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on
mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes
mmc: sdhci-msm: Add support for UHS cards
mmc: sdhci-msm: Add set_uhs_signaling() implementation
...
The workqueue "workq" provides support for sd/mmc async request, which
makes next request do dma_map_sg() while previous request transferring
data.
The workqueue has a single workitem(&host->work) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path. Hence,
the singlethreaded workqueue has been replaced with the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in rtsx_pci_sdmmc_drv_remove() to ensure that
there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The rtsx_pci driver is using a fixed 3s timeout for R1B responses, which
in some cases isn't suffient. For example, erase/discard requests may
require longer timeouts.
Instead of always using a fixed timeout, let's use the per request
calculated busy timeout from the mmc core.
Cc: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Mauro Santos <registo.mailling@gmail.com>
Due to previous changes this define has no longer a purpose. Instead move
the sdhci-pltfm drivers over to use the exported struct sdhci_pltfm_pmops.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the system PM callbacks within #ifdef CONFIG_PM_SLEEP as to avoid
them being build when not used. This also allows us to use the
SET_SYSTEM_SLEEP_PM_OPS macro which simplifies the code.
Within this context it also makes sense to move the declaration of the
struct sdhci_pltfm_pmops, outside the #ifdef CONFIG_PM as the
SET_SYSTEM_SLEEP_PM_OPS deals with this. This further simplifies the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prepare to make the sdhci_pltfm_suspend|resume() static functions, move
sdhci-esdhc-imx over to use the sdhci_suspend|resume_host().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
The system PM callbacks isn't used unless CONFIG_PM_SLEEP is set, thus it
triggers a compiler warning about unused functions. Avoid this by changing
from CONFIG_PM to CONFIG_PM_SLEEP.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b70d0b3b5b29 ("mmc: sdhci-esdhc-imx: add esdhc specific suspend resume callback")
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
The SIMPLE_DEV_PM_OPS macro deals with the CONFIG_PM options when
assigning the PM callbacks, thus it's not needed to control this when
using the macro. By removing the non needed #ifdef, the code becomes a
bit cleaner.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the SET_SYSTEM_SLEEP_PM_OPS and the SET_RUNTIME_PM_OPS macro deals with
the CONFIG_PM options when assigning the callbacks, it becomes redundant
to control this when declaring the struct dev_pm_ops. Instead let's always
declare it as it simplifies the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the SET_SYSTEM_SLEEP_PM_OPS and the SET_RUNTIME_PM_OPS macro deals with
the CONFIG_PM options when assigning the callbacks, it becomes redundant
to control this when declaring the struct dev_pm_ops. Instead let's always
declare it as it simplifies the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's use the SIMPLE_DEV_PM_OPS macro when declaring/assigning the system
PM callbacks, as the code gets simplified.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By using the SET_SYSTEM_SLEEP_PM_OPS when assigning the system PM
callbacks, we can remove some #ifdefs so code becomes a bit cleaner.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert to define the system PM callbacks to be build for CONFIG_PM_SLEEP
and use the SET_SYSTEM_SLEEP_PM_OPS. In this way the code becomes cleaner.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle were:
- Intel-SoC enhancements (Andy Shevchenko)
- Intel CPU symbolic model definition rework (Dave Hansen)
- ... other misc changes"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
x86/sfi: Enable enumeration of SD devices
x86/pci: Use MRFLD abbreviation for Merrifield
x86/platform/intel-mid: Make vertical indentation consistent
x86/platform/intel-mid: Mark regulators explicitly defined
x86/platform/intel-mid: Rename mrfl.c to mrfld.c
x86/platform/intel-mid: Enable spidev on Intel Edison boards
x86/platform/intel-mid: Extend PWRMU to support Penwell
x86/pci, x86/platform/intel_mid_pci: Remove duplicate power off code
x86/platform/intel-mid: Add pinctrl for Intel Merrifield
x86/platform/intel-mid: Enable GPIO expanders on Edison
x86/platform/intel-mid: Add Power Management Unit driver
x86/platform/atom/punit: Enable support for Merrifield
x86/platform/intel_mid_pci: Rework IRQ0 workaround
x86, thermal: Clean up and fix CPU model detection for intel_soc_dts_thermal
x86, mmc: Use Intel family name macros for mmc driver
x86/intel_telemetry: Use Intel family name macros for telemetry driver
x86/acpi/lss: Use Intel family name macros for the acpi_lpss driver
x86/cpufreq: Use Intel family name macros for the intel_pstate cpufreq driver
x86/platform: Use new Intel model number macros
x86/intel_idle: Use Intel family macros for intel_idle
...
This reverts commit 4ac0d5f245e1 ("mmc: sdhci-of-arasan: Always power
the PHY off/on when clock changes"), resolving conflicts with other
patches that have come after. It appears that on some boards / with
some eMMC devices that the patch is causing problems.
Presumably turning the phy off and on again at the wrong time while
initially setting up the card is confusing the card, the host, or the
PHY. We have lots of power cycles while initially setting up the card
because the main sdhci driver often turns off the clock by clearing
SDHCI_CLOCK_CARD_EN and then calls host->ops->set_clock() to set the
clock again. With all of those, we ended up with lots of power cycles.
Presumably the arguments made in the original patch still hold. That
is, whenever the card clock is turned off and on again (or changed) we
really should wait for the DLL to lock again. However, perhaps it's
really not that critical for the lower speeds.
It's possible that the right answer here is:
* Whenever set_clock() is called we should double-check that the DLL is
locked.
* Whenever set_clock() is called and we're actually changing clocks we
should do a power cycle around that.
* When we're doing a power cycle just because the clock changed, we
probably shouldn't do quite as many things (maybe don't need to
recalibarate, etc).
Unfortunately the interaction between SDHCI and the PHY is extremely
limited because of the limited PHY API. The PHY does have a reference
to the card clock and could theoretically register for notifications,
except that our clock is query only (it uses CLK_GET_RATE_NOCACHE) and
so can't really be notified about updates. I believe we would need a
major redesign of clock handling in SDHCI core to do better than that,
or we would need to make our one fake notifications. :(
Let's hope that we can eventually get more information from Arasan on
how all this should be handled before doing tons more work. Until then,
let's get back to a known working state. Note that the rest of the
patches in the 150 MHz series should still work fine even without this
one.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enabling support for ultra high speed mode cards requires some
voltage switching and interaction with the PMIC via a special
power IRQ. Add support for this.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To allow UHS mode to work properly, we need to implement a Qualcomm
specific set_uhs_signaling() callback function. This function differs
from the sdhci_set_uhs_signaling() in that we need check the clock
rate and enable UHS timing only if the frequency is above 100MHz.
This patch resolves the mmc_select_hs200 timeouts noticed after merging
commit a5c1f3e55c99 ("mmc: mmc: do not use CMD13 to get status after
speed mode switch")
mmc0: mmc_select_hs200 failed, error -110
mmc0: error -110 whilst initialising MMC card
mmc0: Reset 0x1 never completed.
sdhci: =========== REGISTER DUMP (mmc0)===========
sdhci: Sys addr: 0x00000000 | Version: 0x00002e02
sdhci: Blk size: 0x00004000 | Blk cnt: 0x00000000
sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci: Present: 0x01f80000 | Host ctl: 0x00000000
sdhci: Power: 0x00000000 | Blk gap: 0x00000000
sdhci: Wake-up: 0x00000000 | Clock: 0x00000003
sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci: Int enab: 0x00000000 | Sig enab: 0x00000000
sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
sdhci: Caps: 0x322dc8b2 | Caps_1: 0x00008007
sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
sdhci: Host ctl2: 0x00000000
sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x0000000000000000
sdhci: ===========================================
Fixes: a5c1f3e55c99 ("mmc: mmc: do not use CMD13 to get status after...")
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The controller does not clear the "reset bit" when it is reset without
a card in the slot. Because of this, the following error message is seen
while booting with no plugged SD card.
mmc1: Reset 0x1 never completed.
Add the SDHCI_QUIRK_NO_CARD_NO_RESET quirk to avoid this.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support UHS modes for Tegra an external regulator must be present
to adjust the IO voltage accordingly. Even if the regulator is not
present but the host supports the UHS modes and the device supports the
UHS modes, then we will attempt to switch to a high-speed mode. Without
an external regulator, Tegra will fail to switch to the high-speed
mode.
It has been found that with some SD cards, that once it has been switch
to operate at a high-speed mode, all subsequent commands issues to the
card will fail and so it will not be possible to switch back to a non
high-speed mode and so the SD card initialisation will fail.
The SDHCI core does not require that the host have an external regulator
when switching to UHS modes and therefore, the Tegra SDHCI host
controller should only advertise the UHS modes as being supported if the
regulator for the IO voltage is present. Fortunately, Tegra has a vendor
specific register which can be used to control which modes are
advertised via the SDHCI_CAPABILITIES register. Hence, if there is no IO
voltage regulator available for the Tegra SDHCI host, then don't
advertise the UHS modes.
Note that if the regulator is not available, we also don't advertise that
the SDHCI is compatible with v3.0 of the SDHCI specification because
this will read the SDHCI_CAPABILITIES_1 register which will enable other
UHS modes.
This fixes commit 7ad2ed1dfc ("mmc: tegra: enable UHS-I modes") which
enables UHS mode without checking if the board can support them.
Fixes: 7ad2ed1dfc ("mmc: tegra: enable UHS-I modes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The capabilities of the SDHCI host controller are read early during the
SDHCI host initialisation in sdhci_setup_host() and before any
regulators for the host have been requested. This means that if the host
supports some high-speed modes (according to its capabilities register),
but the board cannot because the appropriate voltage regulator is not
available, then the host cannot easily override the capabilities that
are supported.
To allow a SDHCI host controller to determine if it can support UHS high
speed modes via the presence of the MMC regulators, request the
regulators before reading the capabilities of the host controller. This
will allow the SDHCI host to use the 'reset' callback to take the
appropriate action (set flags, configure registers, etc) before the
capabilities register(s) are read.
Please note that some SDHCI hosts, such as the Tegra SDHCI host, has
the ability to mask bits in the capabilities register to prevent
certain capabilities from being advertised.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Everywhere else in the code MRFLD abbreviation is used for Intel Merrifield. Do
the same for sdhci-pci.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The tuning bits like FBCLK_SEL, SMP_CLK_SEL and DLY_CELL which affects
timing may have already been set by ROM if booting from SD3.0 mode like
SDR104. Let's clear it first during driver probe before doing the new
card enumeration to avoid working on the wrong timing.
Note that tuning bits are dynamical settings which may need to be kept
during MMC_PM_KEEP_POWER suspend, so we did not put them into hwinit
function.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_esdhc_imx_hwinit() includes all basic hw intialization.
Calling it after resume to re-initialize hw in case its state
is already lost in low power mode.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move tuning static configuration into basic hwinit function.
Tuning configuration may also be lost in low power mode, so
need restore in hwinit().
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move all hw related static initializations into a separate function
which helps concentrate the hw related initialization code.
And that function could also be called by other places later as a
basic hw state restore.
e.g. suspend/resume where the hw state is possible to lost due to
low power mode.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When enable DDR, the clock factor definition is changed.
e.g. original 200Mhz will become 100Mhz once MIX_CTRL_DDREN bit is set
So we need to update the clock setting then the strobe dll can lock
the correct clock rate.
Additionally we also need disable the clock before locking strobe dll.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Indicating hw auto retuning support for mx6qdl in the fake caps_1
register and enable auto retuning in post_tuning process after
tuning completes.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable HW auto retuning when set SDHCI_CTRL_EXEC_TUNING and clear it
when clear SDHCI_CTRL_TUNED_CLK.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If HW supports SDHCI_TUNING_MODE_3 which is auto retuning, we won't
retune during runtime suspend and resume, instead we use Re-tuning
Request signaled via SDHCI_INT_RETUNE interrupt to do retuning and
hw auto retuning during data transfer to guarantee the signal sample
window correction.
This can avoid a mass of repeatedly retuning during small file system
data access and improve the performance.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The delay cells of some SoCs may have less delay per one cell,
for such SoCs, user could set the start delay cell point to bypass
the first a few meaningless tuning commands.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disable DLL delay line settings explicitly during driver initialization
in case ROM/uBoot had set an invalid delay.
e.g. MX6DL ROM has set the default delay line(DLLCTRL) to 0x1000021,
the uSDHC clock timing will become marginal when works on DDR mode
due to default delay and will possibly see CRC errors in case the board
is not perfectly designed on the eMMC chip layout.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, we config the watermark_level register only in probe.
This will cause the mmc write operation timeout issue after system
resume back in LPSR mode. Because in LPSR mode, after system resume
back, the watermark_level register(0x44) changes to 0x08000880, which
set the write watermark level as 0, and set the read watermark level
as 128. This value is incorrect.
This patch restores the setting of watermark level register after
system resume back.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It will be used for platform specific suspend/resume state save/restore
work for some low power mode like Mega/Fast or LPSR mode.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver has already implemented the private .set_timeout()
callback for common SDHCI code to do correct timeout value setting,
it does not need call sdhci_calc_timeout(), so this quirk actually
is not working. Remove it now.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch to use the more robust common mmc_regulator_set_vqmmc()
function in MMC core which set the target voltage as close as
possible to target voltage.
We did not re-factor the whole sdhci_start_signal_voltage_switch()
cause we want to keep the original signal switch order between host
and card to avoid potential break.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In dw_mmc.c, it's enabled by default.
It doesn't need to set MMC_CAP_ERASE in rockchip anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This flag needs to use the trim/discard/erase commands.
dwmmc controller enables this flag by default.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The capabilities in iproc platform data are magic numbers. So
replace them with the proper capability defines to make it
readable.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the missing define for the suspend/resume
capability (according to SD Host Controller spec).
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
