Commit ce0aa27ff3 ("sfp: add sfp-bus to bridge between network devices
and sfp cages") added code which finds SFP bus DT node even if the node
is disabled with status = "disabled". Because of this, when phylink is
created, it ends with non-null .sfp_bus member, even though the SFP
module is not probed (because the node is disabled).
We need to ignore disabled SFP bus node.
Fixes: ce0aa27ff3 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 2203cbf2c8 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: David S. Miller <davem@davemloft.net>
With current KPU profile NGIO is being parsed along with CTAG as
a single layer. Because of this MCAM/ntuple rules installed with
ethertype as 0x8842 are not being hit. Adding KPU profile changes
to parse NGIO in separate ltype and CTAG in separate ltype.
Fixes: f9c49be90c ("octeontx2-af: Update the default KPU profile and fixes")
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF forwards its VF messages to AF and corresponding
replies from AF to VF. AF sets proper error code in the
replies after processing message requests. Currently PF
checks the error codes in replies and sends invalid
message to VF. This way VF lacks the information of
error code set by AF for its messages. This patch
changes that such that PF simply forwards AF replies
so that VF can handle error codes.
Fixes: d424b6c024 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal looback is not supported to low rate LPCS interface like
SGMII/QSGMII. Hence don't allow to enable for such interfaces.
Fixes: 3ad3f8f93c ("octeontx2-af: cn10k: MAC internal loopback support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been observed that sometimes link credit restore takes
a lot of time than the current timeout. This patch increases
the default timeout value and return the proper error value
on failure.
Fixes: 1c74b89171 ("octeontx2-af: Wait for TX link idle for credits change")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While freeing SQB pointers to aura, driver first memcpy to
target address and then triggers lmtst operation to free pointer
to the aura. We need to ensure(by adding dmb barrier)that memcpy
is finished before pointers are freed to the aura. This patch also
adds the missing sq context structure entry in debugfs.
Fixes: ef6c8da71e ("octeontx2-pf: cn10K: Reserve LMTST lines per core")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K platforms uses RPM(0..2)_MTI_MAC100(0..3)_COMMAND_CONFIG
register for lmac TX/RX enable whereas CN9xxx platforms use
CGX_CMRX_CONFIG register. This config change was missed when
adding support for CN10K RPM.
Fixes: 91c6945ea1 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few RVU blocks like SSO require more time for reset on some
silicons. Hence retrying the block reset until success.
Fixes: c0fa2cff88 ("octeontx2-af: Handle return value in block reset")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rvu_nix_get_bpid() lbk_bpid_cnt is being read from
wrong register. Due to this backpressure enable is failing
for LBK VF32 onwards. This patch fixes that.
Fixes: fe1939bb23 ("octeontx2-af: Add SDP interface support")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AF modifies all the rules destined for VF to use
the action same as default RSS action. This fixup
was needed because AF only installs default rules with
RSS action. But the action in rules installed by a PF
for its VFs should not be changed by this fixup.
This is because action can be drop or direct to
queue as specified by user(ntuple filters).
This patch fixes that problem.
Fixes: 967db3529e ("octeontx2-af: add support for multicast/promisc packet")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-01-20
This series contains updates to i40e driver only.
Jedrzej increases delay for EMP reset and adds checks to ensure a VF
request to change queues can be met.
Sylwester moves the placement of the Flow Director queue as to not
fragment the queue pile which would cause later re-allocation issues.
Karen prevents VF reset being invoked while another is still occurring
to avoid reading invalid data.
Joe Damato fixes some statistics fields to match the values of the
fields they are based on.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bafbdd527d ("phylib: Add device reset GPIO support") added call
to phy_device_reset(phydev) after the put_device() call in phy_detach().
The comment before the put_device() call says that the phydev might go
away with put_device().
Fix potential use-after-free by calling phy_device_reset() before
put_device().
Fixes: bafbdd527d ("phylib: Add device reset GPIO support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220119162748.32418-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change i40e_update_vsi_stats and struct i40e_vsi to use u64 fields to match
the width of the stats counters in struct i40e_rx_queue_stats.
Update debugfs code to use the correct format specifier for u64.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix for failed to init adminq: -53 while VF is resetting via MAC
address changing procedure.
Added sync module to avoid reading deadbeef value in reinit adminq
during software reset.
Without this patch it is possible to trigger VF reset procedure
during reinit adminq. This resulted in an incorrect reading of
value from the AQP registers and generated the -53 error.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When XDP was configured on a system with large number of CPUs
and X722 NIC there was a call trace with NULL pointer dereference.
i40e 0000:87:00.0: failed to get tracking for 256 queues for VSI 0 err -12
i40e 0000:87:00.0: setup of MAIN VSI failed
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:i40e_xdp+0xea/0x1b0 [i40e]
Call Trace:
? i40e_reconfig_rss_queues+0x130/0x130 [i40e]
dev_xdp_install+0x61/0xe0
dev_xdp_attach+0x18a/0x4c0
dev_change_xdp_fd+0x1e6/0x220
do_setlink+0x616/0x1030
? ahci_port_stop+0x80/0x80
? ata_qc_issue+0x107/0x1e0
? lock_timer_base+0x61/0x80
? __mod_timer+0x202/0x380
rtnl_setlink+0xe5/0x170
? bpf_lsm_binder_transaction+0x10/0x10
? security_capable+0x36/0x50
rtnetlink_rcv_msg+0x121/0x350
? rtnl_calcit.isra.0+0x100/0x100
netlink_rcv_skb+0x50/0xf0
netlink_unicast+0x1d3/0x2a0
netlink_sendmsg+0x22a/0x440
sock_sendmsg+0x5e/0x60
__sys_sendto+0xf0/0x160
? __sys_getsockname+0x7e/0xc0
? _copy_from_user+0x3c/0x80
? __sys_setsockopt+0xc8/0x1a0
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f83fa7a39e0
This was caused by PF queue pile fragmentation due to
flow director VSI queue being placed right after main VSI.
Because of this main VSI was not able to resize its
queue allocation for XDP resulting in no queues allocated
for main VSI when XDP was turned on.
Fix this by always allocating last queue in PF queue pile
for a flow director VSI.
Fixes: 41c445ff0f ("i40e: main driver core")
Fixes: 74608d17fe ("i40e: add support for XDP_TX action")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Before this patch VF interface vanished when
maximum queue number was exceeded. Driver tried
to add next queues even if there was not enough
space. PF sent incorrect number of queues to
the VF when there were not enough of them.
Add an additional condition introduced to check
available space in 'qp_pile' before proceeding.
This condition makes it impossible to add queues
if they number is greater than the number resulting
from available space.
Also add the search for free space in PF queue
pair piles.
Without this patch VF interfaces are not seen
when available space for queues has been
exceeded and following logs appears permanently
in dmesg:
"Unable to get VF config (-32)".
"VF 62 failed opcode 3, retval: -5"
"Unable to get VF config due to PF error condition, not retrying"
Fixes: 7daa6bf329 ("i40e: driver core headers")
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recently simplified i40e_rebuild causes that FW sometimes
is not ready after NVM update, the ping does not return.
Increase the delay in case of EMP reset.
Old delay of 300 ms was introduced for specific cards for 710 series.
Now it works for all the cards and delay was increased.
Fixes: 1fa51a650e ("i40e: Add delay after EMP reset for firmware to recover")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Bit pattern of the ETHER_CLOCK_SEL register for RMII/MII mode should be fixed.
Also, some control bits should be modified with a specific sequence.
Fixes: b38dd98ff8 ("net: stmmac: Add Toshiba Visconti SoCs glue driver")
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
A problem was encountered with the Bel-Fuse 1GBT-SFP05 SFP module (which
is a 1 Gbps copper module operating in SGMII mode with an internal
BCM54616S PHY device) using the Xilinx AXI Ethernet MAC core, where the
module would work properly on the initial insertion or boot of the
device, but after the device was rebooted, the link would either only
come up at 100 Mbps speeds or go up and down erratically.
I found no meaningful changes in the PHY configuration registers between
the working and non-working boots, but the status registers seemed to
have a lot of error indications set on the SERDES side of the device on
the non-working boot. I suspect the problem is that whatever happens on
the SGMII link when the device is rebooted and the FPGA logic gets
reloaded ends up putting the module's onboard PHY into a bad state.
Since commit 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
the genphy_soft_reset call is not made automatically by the PHY core
unless the callback is explicitly specified in the driver structure. For
most of these Broadcom devices, there is probably a hardware reset that
gets asserted to reset the PHY during boot, however for SFP modules
(where the BCM54616S is commonly found) no such reset line exists, so if
the board keeps the SFP cage powered up across a reboot, it will end up
with no reset occurring during reboots.
Hook up the genphy_soft_reset callback for BCM54616S to ensure that a
PHY reset is performed before the device is initialized. This appears to
fix the issue with erratic operation after a reboot with this SFP
module.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - regressions:
- fix memory leaks in the skb free deferral scheme if upper layer
protocols are used, i.e. in-kernel TCP readers like TLS
Current release - new code bugs:
- nf_tables: fix NULL check typo in _clone() functions
- change the default to y for Vertexcom vendor Kconfig
- a couple of fixes to incorrect uses of ref tracking
- two fixes for constifying netdev->dev_addr
Previous releases - regressions:
- bpf:
- various verifier fixes mainly around register offset handling
when passed to helper functions
- fix mount source displayed for bpffs (none -> bpffs)
- bonding:
- fix extraction of ports for connection hash calculation
- fix bond_xmit_broadcast return value when some devices are down
- phy: marvell: add Marvell specific PHY loopback
- sch_api: don't skip qdisc attach on ingress, prevent ref leak
- htb: restore minimal packet size handling in rate control
- sfp: fix high power modules without diagnostic monitoring
- mscc: ocelot:
- don't let phylink re-enable TX PAUSE on the NPI port
- don't dereference NULL pointers with shared tc filters
- smsc95xx: correct reset handling for LAN9514
- cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
- phy: micrel: use kszphy_suspend/_resume for irq aware devices,
avoid races with the interrupt
Previous releases - always broken:
- xdp: check prog type before updating BPF link
- smc: resolve various races around abnormal connection termination
- sit: allow encapsulated IPv6 traffic to be delivered locally
- axienet: fix init/reset handling, add missing barriers,
read the right status words, stop queues correctly
- add missing dev_put() in sock_timestamping_bind_phc()
Misc:
- ipv4: prevent accidentally passing RTO_ONLINK to
ip_route_output_key_hash() by sanitizing flags
- ipv4: avoid quadratic behavior in netns dismantle
- stmmac: dwmac-oxnas: add support for OX810SE
- fsl: xgmac_mdio: add workaround for erratum A-009885
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XM4Y
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, bpf.
Quite a handful of old regression fixes but most of those are
pre-5.16.
Current release - regressions:
- fix memory leaks in the skb free deferral scheme if upper layer
protocols are used, i.e. in-kernel TCP readers like TLS
Current release - new code bugs:
- nf_tables: fix NULL check typo in _clone() functions
- change the default to y for Vertexcom vendor Kconfig
- a couple of fixes to incorrect uses of ref tracking
- two fixes for constifying netdev->dev_addr
Previous releases - regressions:
- bpf:
- various verifier fixes mainly around register offset handling
when passed to helper functions
- fix mount source displayed for bpffs (none -> bpffs)
- bonding:
- fix extraction of ports for connection hash calculation
- fix bond_xmit_broadcast return value when some devices are down
- phy: marvell: add Marvell specific PHY loopback
- sch_api: don't skip qdisc attach on ingress, prevent ref leak
- htb: restore minimal packet size handling in rate control
- sfp: fix high power modules without diagnostic monitoring
- mscc: ocelot:
- don't let phylink re-enable TX PAUSE on the NPI port
- don't dereference NULL pointers with shared tc filters
- smsc95xx: correct reset handling for LAN9514
- cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
- phy: micrel: use kszphy_suspend/_resume for irq aware devices,
avoid races with the interrupt
Previous releases - always broken:
- xdp: check prog type before updating BPF link
- smc: resolve various races around abnormal connection termination
- sit: allow encapsulated IPv6 traffic to be delivered locally
- axienet: fix init/reset handling, add missing barriers, read the
right status words, stop queues correctly
- add missing dev_put() in sock_timestamping_bind_phc()
Misc:
- ipv4: prevent accidentally passing RTO_ONLINK to
ip_route_output_key_hash() by sanitizing flags
- ipv4: avoid quadratic behavior in netns dismantle
- stmmac: dwmac-oxnas: add support for OX810SE
- fsl: xgmac_mdio: add workaround for erratum A-009885"
* tag 'net-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits)
ipv4: add net_hash_mix() dispersion to fib_info_laddrhash keys
ipv4: avoid quadratic behavior in netns dismantle
net/fsl: xgmac_mdio: Fix incorrect iounmap when removing module
powerpc/fsl/dts: Enable WA for erratum A-009885 on fman3l MDIO buses
dt-bindings: net: Document fsl,erratum-a009885
net/fsl: xgmac_mdio: Add workaround for erratum A-009885
net: mscc: ocelot: fix using match before it is set
net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices
net: cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
nfc: llcp: fix NULL error pointer dereference on sendmsg() after failed bind()
net: axienet: increase default TX ring size to 128
net: axienet: fix for TX busy handling
net: axienet: fix number of TX ring slots for available check
net: axienet: Fix TX ring slot available check
net: axienet: limit minimum TX ring size
net: axienet: add missing memory barriers
net: axienet: reset core on initialization prior to MDIO access
net: axienet: Wait for PhyRstCmplt after core reset
net: axienet: increase reset timeout
bpf, selftests: Add ringbuf memory type confusion test
...
Merge more updates from Andrew Morton:
"55 patches.
Subsystems affected by this patch series: percpu, procfs, sysctl,
misc, core-kernel, get_maintainer, lib, checkpatch, binfmt, nilfs2,
hfs, fat, adfs, panic, delayacct, kconfig, kcov, and ubsan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (55 commits)
lib: remove redundant assignment to variable ret
ubsan: remove CONFIG_UBSAN_OBJECT_SIZE
kcov: fix generic Kconfig dependencies if ARCH_WANTS_NO_INSTR
lib/Kconfig.debug: make TEST_KMOD depend on PAGE_SIZE_LESS_THAN_256KB
btrfs: use generic Kconfig option for 256kB page size limit
arch/Kconfig: split PAGE_SIZE_LESS_THAN_256KB from PAGE_SIZE_LESS_THAN_64KB
configs: introduce debug.config for CI-like setup
delayacct: track delays from memory compact
Documentation/accounting/delay-accounting.rst: add thrashing page cache and direct compact
delayacct: cleanup flags in struct task_delay_info and functions use it
delayacct: fix incomplete disable operation when switch enable to disable
delayacct: support swapin delay accounting for swapping without blkio
panic: remove oops_id
panic: use error_report_end tracepoint on warnings
fs/adfs: remove unneeded variable make code cleaner
FAT: use io_schedule_timeout() instead of congestion_wait()
hfsplus: use struct_group_attr() for memcpy() region
nilfs2: remove redundant pointer sbufs
fs/binfmt_elf: use PT_LOAD p_align values for static PIE
const_structs.checkpatch: add frequently used ops structs
...
When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.
Replace kernel.h inclusion with the list of what is really being used.
The rest of the changes are induced by the above and may not be split.
Link: https://lkml.kernel.org/r/20211209123823.20425-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> [brcmfmac]
Acked-by: Kalle Valo <kvalo@kernel.org>
Cc: Arend van Spriel <aspriel@gmail.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-hsien Lin <chi-hsien.lin@infineon.com>
Cc: Wright Feng <wright.feng@infineon.com>
Cc: Chung-hsien Hsu <chung-hsien.hsu@infineon.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported by sparse: In the remove path, the driver would attempt to
unmap its own priv pointer - instead of the io memory that it mapped
in probe.
Fixes: 9f35a7342c ("net/fsl: introduce Freescale 10G MDIO driver")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Once an MDIO read transaction is initiated, we must read back the data
register within 16 MDC cycles after the transaction completes. Outside
of this window, reads may return corrupt data.
Therefore, disable local interrupts in the critical section, to
maximize the probability that we can satisfy this requirement.
Fixes: d55ad2967d ("powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clang static analysis reports this issue
ocelot_flower.c:563:8: warning: 1st function call argument
is an uninitialized value
!is_zero_ether_addr(match.mask->dst)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The variable match is used before it is set. So move the
block.
Fixes: 75944fda1d ("net: mscc: ocelot: offload ingress skbedit and vlan actions to VCAP IS1")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a setup with KSZ9131 and MACB drivers it happens on suspend path, from
time to time, that the PHY interrupt arrives after PHY and MACB were
suspended (PHY via genphy_suspend(), MACB via macb_suspend()). In this
case the phy_read() at the beginning of kszphy_handle_interrupt() will
fail (as MACB driver is suspended at this time) leading to phy_error()
being called and a stack trace being displayed on console. To solve this
.suspend/.resume functions for all KSZ devices implementing
.handle_interrupt were replaced with kszphy_suspend()/kszphy_resume()
which disable/enable interrupt before/after calling
genphy_suspend()/genphy_resume().
The fix has been adapted for all KSZ devices which implements
.handle_interrupt but it has been tested only on KSZ9131.
Fixes: 59ca4e58b9 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both versions of the CPSW driver declare a CPSW_HEADROOM_NA macro that
takes NET_IP_ALIGN into account, but fail to use it appropriately when
storing incoming packets in memory. This results in the IPv4 source and
destination addresses to appear misaligned in memory, which causes
aligment faults that need to be fixed up in software.
So let's switch from CPSW_HEADROOM to CPSW_HEADROOM_NA where needed.
This gets rid of any alignment faults on the RX path on a Beaglebone
White.
Fixes: 9ed4050c0d ("net: ethernet: ti: cpsw: add XDP support")
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With previous changes to make the driver handle the TX ring size more
correctly, the default TX ring size of 64 appears to significantly
bottleneck TX performance to around 600 Mbps on a 1 Gbps link on ZynqMP.
Increasing this to 128 seems to bring performance up to near line rate and
shouldn't cause excess bufferbloat (this driver doesn't yet support modern
byte-based queue management).
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network driver documentation indicates we should be avoiding returning
NETDEV_TX_BUSY from ndo_start_xmit in normal cases, since it requires
the packets to be requeued. Instead the queue should be stopped after
a packet is added to the TX ring when there may not be enough room for an
additional one. Also, when TX ring entries are completed, we should only
wake the queue if we know there is room for another full maximally
fragmented packet.
Print a warning if there is insufficient space at the start of start_xmit,
since this should no longer happen.
Combined with increasing the default TX ring size (in a subsequent
patch), this appears to recover the TX performance lost by previous changes
to actually manage the TX ring state properly.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for the number of available TX ring slots was off by 1 since a
slot is required for the skb header as well as each fragment. This could
result in overwriting a TX ring slot that was still in use.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for whether a TX ring slot was available was incorrect,
since a slot which had been loaded with transmit data but the device had
not started transmitting would be treated as available, potentially
causing non-transmitted slots to be overwritten. The control field in
the descriptor should be checked, rather than the status field (which may
only be updated when the device completes the entry).
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will not work properly if the TX ring size is set to below
MAX_SKB_FRAGS + 1 since it needs to hold at least one full maximally
fragmented packet in the TX ring. Limit setting the ring size to below
this value.
Fixes: 8b09ca823f ("net: axienet: Make RX/TX ring sizes configurable")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was missing some required memory barriers:
Use dma_rmb to ensure we see all updates to the descriptor after we see
that an entry has been completed.
Use wmb and rmb to avoid stale descriptor status between the TX path and
TX complete IRQ path.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases where the Xilinx Ethernet core was used in 1000Base-X or
SGMII modes, which use the internal PCS/PMA PHY, and the MGT
transceiver clock source for the PCS was not running at the time the
FPGA logic was loaded, the core would come up in a state where the
PCS could not be found on the MDIO bus. To fix this, the Ethernet core
(including the PCS) should be reset after enabling the clocks, prior to
attempting to access the PCS using of_mdio_find_device.
Fixes: 1a02556086 (net: axienet: Properly handle PCS/PMA PHY for 1000BaseX mode)
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting the device, wait for the PhyRstCmplt bit to be set
in the interrupt status register before continuing initialization, to
ensure that the core is actually ready. When using an external PHY, this
also ensures we do not start trying to access the PHY while it is still
in reset. The PHY reset is initiated by the core reset which is
triggered just above, but remains asserted for 5ms after the core is
reset according to the documentation.
The MgtRdy bit could also be waited for, but unfortunately when using
7-series devices, the bit does not appear to work as documented (it
seems to behave as some sort of link state indication and not just an
indication the transceiver is ready) so it can't really be relied on for
this purpose.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous timeout of 1ms was too short to handle some cases where the
core is reset just after the input clocks were started, which will
be introduced in an upcoming patch. Increase the timeout to 50ms. Also
simplify the reset timeout checking to use read_poll_timeout.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically nobody should use blake2s in an HMAC construction; it already
has a keyed variant. But unfortunately for historical reasons, Noise,
used by WireGuard, uses HKDF quite strictly, which means we have to use
this. Because this really shouldn't be used by others, this commit moves
it into wireguard's noise.c locally, so that kernels that aren't using
WireGuard don't get this superfluous code baked in. On m68k systems,
this shaves off ~314 bytes.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
partial support for < MAX_ORDER - 1 granularity for virtio-mem
driver_override for vdpa
sysfs ABI documentation for vdpa
multiqueue config support for mlx5 vdpa
Misc fixes, cleanups.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmHiDHkPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpVT4H/3Veixt3uYPOmuLU2tSx+8X+sFTtik81hyiE
okz5fRJrxxA8SqS76FnmO10FS4hlPOGNk0Z5WVhr0yihwFvPLvpCM/xi2Lmrz9I7
pB0sXOIocEL1xApsxukR9K1Twpb2hfYsflbJYUVlRfhS5G0izKJNZp5I7OPrzd80
vVNNDWKW2iLDlfqsavumI4Kvm4nsFuCHG03jzMtcIa7YTXYV3DORD4ZGFFVUOIQN
t5F74TznwHOeYgJeg7TzjFjfPWmXjLetvx10QX1A1uOvwppWW/QY6My0UafTXNXj
VB3gOwJPf+gxXAXl/4bafq4NzM0xys6cpcPpjvhmU+erY4UuyAU=
=Y1eO
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio,vdpa,qemu_fw_cfg: features, cleanups, and fixes.
- partial support for < MAX_ORDER - 1 granularity for virtio-mem
- driver_override for vdpa
- sysfs ABI documentation for vdpa
- multiqueue config support for mlx5 vdpa
- and misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (42 commits)
vdpa/mlx5: Fix tracking of current number of VQs
vdpa/mlx5: Fix is_index_valid() to refer to features
vdpa: Protect vdpa reset with cf_mutex
vdpa: Avoid taking cf_mutex lock on get status
vdpa/vdpa_sim_net: Report max device capabilities
vdpa: Use BIT_ULL for bit operations
vdpa/vdpa_sim: Configure max supported virtqueues
vdpa/mlx5: Report max device capabilities
vdpa: Support reporting max device capabilities
vdpa/mlx5: Restore cur_num_vqs in case of failure in change_num_qps()
vdpa: Add support for returning device configuration information
vdpa/mlx5: Support configuring max data virtqueue
vdpa/mlx5: Fix config_attr_mask assignment
vdpa: Allow to configure max data virtqueues
vdpa: Read device configuration only if FEATURES_OK
vdpa: Sync calls set/get config/status with cf_mutex
vdpa/mlx5: Distribute RX virtqueues in RQT object
vdpa: Provide interface to read driver features
vdpa: clean up get_config_size ret value handling
virtio_ring: mark ring unused on error
...
Commit 7cfa9c92d0 ("net: sfp: avoid power switch on address-change
modules") unintetionally changed the semantics for high power modules
without the digital diagnostics monitoring. We repeatedly attempt to
read the power status from the non-existing 0xa2 address in a futile
hope this failure is temporary:
[ 8.856051] sfp sfp-eth3: module NTT 0000000000000000 rev 0000 sn 0000000000000000 dc 160408
[ 8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode
[ 8.873469] sfp sfp-eth3: Failed to read EEPROM: -5
[ 8.983251] sfp sfp-eth3: Failed to read EEPROM: -5
[ 9.103250] sfp sfp-eth3: Failed to read EEPROM: -5
We previosuly assumed such modules were powered up in the correct mode,
continuing without further configuration as long as the required power
class was supported by the host.
Restore this behaviour, while preserving the intent of subsequent
patches to avoid the "Address Change Sequence not supported" warning
if we are not going to be accessing the DDM address.
Fixes: 7cfa9c92d0 ("net: sfp: avoid power switch on address-change modules")
Reported-by: 照山周一郎 <teruyama@springboard-inc.jp>
Tested-by: 照山周一郎 <teruyama@springboard-inc.jp>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the blamed commit, the call to the function
switchdev_bridge_port_offload was passing the wrong argument for
atomic_nb. It was ocelot_netdevice_nb instead of ocelot_swtchdev_nb.
This patch fixes this issue.
Fixes: 4e51bf44a0 ("net: bridge: move the switchdev object replay helpers to "push" mode")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull signal/exit/ptrace updates from Eric Biederman:
"This set of changes deletes some dead code, makes a lot of cleanups
which hopefully make the code easier to follow, and fixes bugs found
along the way.
The end-game which I have not yet reached yet is for fatal signals
that generate coredumps to be short-circuit deliverable from
complete_signal, for force_siginfo_to_task not to require changing
userspace configured signal delivery state, and for the ptrace stops
to always happen in locations where we can guarantee on all
architectures that the all of the registers are saved and available on
the stack.
Removal of profile_task_ext, profile_munmap, and profile_handoff_task
are the big successes for dead code removal this round.
A bunch of small bug fixes are included, as most of the issues
reported were small enough that they would not affect bisection so I
simply added the fixes and did not fold the fixes into the changes
they were fixing.
There was a bug that broke coredumps piped to systemd-coredump. I
dropped the change that caused that bug and replaced it entirely with
something much more restrained. Unfortunately that required some
rebasing.
Some successes after this set of changes: There are few enough calls
to do_exit to audit in a reasonable amount of time. The lifetime of
struct kthread now matches the lifetime of struct task, and the
pointer to struct kthread is no longer stored in set_child_tid. The
flag SIGNAL_GROUP_COREDUMP is removed. The field group_exit_task is
removed. Issues where task->exit_code was examined with
signal->group_exit_code should been examined were fixed.
There are several loosely related changes included because I am
cleaning up and if I don't include them they will probably get lost.
The original postings of these changes can be found at:
https://lkml.kernel.org/r/87a6ha4zsd.fsf@email.froward.int.ebiederm.orghttps://lkml.kernel.org/r/87bl1kunjj.fsf@email.froward.int.ebiederm.orghttps://lkml.kernel.org/r/87r19opkx1.fsf_-_@email.froward.int.ebiederm.org
I trimmed back the last set of changes to only the obviously correct
once. Simply because there was less time for review than I had hoped"
* 'signal-for-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (44 commits)
ptrace/m68k: Stop open coding ptrace_report_syscall
ptrace: Remove unused regs argument from ptrace_report_syscall
ptrace: Remove second setting of PT_SEIZED in ptrace_attach
taskstats: Cleanup the use of task->exit_code
exit: Use the correct exit_code in /proc/<pid>/stat
exit: Fix the exit_code for wait_task_zombie
exit: Coredumps reach do_group_exit
exit: Remove profile_handoff_task
exit: Remove profile_task_exit & profile_munmap
signal: clean up kernel-doc comments
signal: Remove the helper signal_group_exit
signal: Rename group_exit_task group_exec_task
coredump: Stop setting signal->group_exit_task
signal: Remove SIGNAL_GROUP_COREDUMP
signal: During coredumps set SIGNAL_GROUP_EXIT in zap_process
signal: Make coredump handling explicit in complete_signal
signal: Have prepare_signal detect coredumps using signal->core_state
signal: Have the oom killer detect coredumps using signal->core_state
exit: Move force_uaccess back into do_exit
exit: Guarantee make_task_dead leaks the tsk when calling do_task_exit
...
Wrong hash sends single stream to multiple output interfaces.
The offset calculation was relative to skb->head, fix it to be relative
to skb->data.
Fixes: a815bde56b ("net, bonding: Refactor bond_xmit_hash for use with
xdp_buff")
Reviewed-by: Jussi Maki <joamaki@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Moshe Tal <moshet@nvidia.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmHhw7oTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXrjSB/979LV4Dn1PMcFYsSdlFEMeHcjzJdw/
kFnLPXMaPJyfg6QPuf83jxzw9uxw8fcePMdVq/FFBtmVV9fJMAv62B8jaGS1p58c
WnAg+7zsTN+xEoJn+tskSSon8BNMWVrl41zP3K4Ged+5j8UEBk62GB8Orz1qkpwL
fTh3/+xAvczJeD4zZb1dAm4WnmcQJ4vhg45p07jX6owvnwQAikMFl45aSW54I5o8
vAxGzFgdsZ2NtExnRNKh3b3DozA8JUE89KckBSZnDtq4rH8Fyy6Wij56Hc6v6Cml
SUohiNbHX7hsNwit/lxL8wuF97IiA0pQSABobEg3rxfTghTUep51LlaN
=/m4A
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed-20220114' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- More patches for Hyper-V isolation VM support (Tianyu Lan)
- Bug fixes and clean-up patches from various people
* tag 'hyperv-next-signed-20220114' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
scsi: storvsc: Fix storvsc_queuecommand() memory leak
x86/hyperv: Properly deal with empty cpumasks in hyperv_flush_tlb_multi()
Drivers: hv: vmbus: Initialize request offers message for Isolation VM
scsi: storvsc: Fix unsigned comparison to zero
swiotlb: Add CONFIG_HAS_IOMEM check around swiotlb_mem_remap()
x86/hyperv: Fix definition of hv_ghcb_pg variable
Drivers: hv: Fix definition of hypercall input & output arg variables
net: netvsc: Add Isolation VM support for netvsc driver
scsi: storvsc: Add Isolation VM support for storvsc driver
hyper-v: Enable swiotlb bounce buffer for Isolation VM
x86/hyper-v: Add hyperv Isolation VM check in the cc_platform_has()
swiotlb: Add swiotlb bounce buffer remap function for HV IVM
In pci_generic.c there is a 'mru_default' in struct mhi_pci_dev_info.
This value shall be used for whole mhi if it's given a value for a specific product.
But in function mhi_net_rx_refill_work(), it's still using hard code value MHI_DEFAULT_MRU.
'mru_default' shall have higher priority than MHI_DEFAULT_MRU.
And after checking, this change could help fix a data connection lost issue.
Fixes: 5c2c853159 ("bus: mhi: pci-generic: configurable network interface MRU")
Signed-off-by: Shujun Wang <wsj20369@163.com>
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing genphy_loopback() is not applicable for Marvell PHY. Besides
configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control
Register), it is also required to configure same bits in Page 2
Register 21 (MAC Specific Control Register 2) according to speed of
the loopback is operating.
Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).
FIXME: Based on trial and error test, it seem 1G need to have delay between
soft reset and loopback enablement.
Fixes: 014068dcb5 ("net: phy: genphy_loopback: add link speed configuration")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A dma_request_chan() call is hidden in emac_configure_dma().
It must be released in the probe if an error occurs, as already done in
the remove function.
Add the corresponding dma_release_channel() call.
Fixes: 47869e82c8 ("sun4i-emac.c: add dma support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang static analysis reports this problem
mtk_eth_soc.c:394:7: warning: Branch condition evaluates
to a garbage value
if (err)
^~~
err is not initialized and only conditionally set.
So intitialize err.
Fixes: 7e53837269 ("net: ethernet: mediatek: Re-add support SGMII")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following command sequence:
tc qdisc del dev swp0 clsact
tc qdisc add dev swp0 ingress_block 1 clsact
tc qdisc add dev swp1 ingress_block 1 clsact
tc filter add block 1 flower action drop
tc qdisc del dev swp0 clsact
produces the following NPD:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000014
pc : vcap_entry_set+0x14/0x70
lr : ocelot_vcap_filter_del+0x198/0x234
Call trace:
vcap_entry_set+0x14/0x70
ocelot_vcap_filter_del+0x198/0x234
ocelot_cls_flower_destroy+0x94/0xe4
felix_cls_flower_del+0x70/0x84
dsa_slave_setup_tc_block_cb+0x13c/0x60c
dsa_slave_setup_tc_block_cb_ig+0x20/0x30
tc_setup_cb_reoffload+0x44/0x120
fl_reoffload+0x280/0x320
tcf_block_playback_offloads+0x6c/0x184
tcf_block_unbind+0x80/0xe0
tcf_block_setup+0x174/0x214
tcf_block_offload_cmd.isra.0+0x100/0x13c
tcf_block_offload_unbind+0x5c/0xa0
__tcf_block_put+0x54/0x174
tcf_block_put_ext+0x5c/0x74
clsact_destroy+0x40/0x60
qdisc_destroy+0x4c/0x150
qdisc_put+0x70/0x90
qdisc_graft+0x3f0/0x4c0
tc_get_qdisc+0x1cc/0x364
rtnetlink_rcv_msg+0x124/0x340
The reason is that the driver isn't prepared to receive two tc filters
with the same cookie. It unconditionally creates a new struct
ocelot_vcap_filter for each tc filter, and it adds all filters with the
same identifier (cookie) to the ocelot_vcap_block.
The problem is here, in ocelot_vcap_filter_del():
/* Gets index of the filter */
index = ocelot_vcap_block_get_filter_index(block, filter);
if (index < 0)
return index;
/* Delete filter */
ocelot_vcap_block_remove_filter(ocelot, block, filter);
/* Move up all the blocks over the deleted filter */
for (i = index; i < block->count; i++) {
struct ocelot_vcap_filter *tmp;
tmp = ocelot_vcap_block_find_filter_by_index(block, i);
vcap_entry_set(ocelot, i, tmp);
}
what will happen is ocelot_vcap_block_get_filter_index() will return the
index (@index) of the first filter found with that cookie. This is _not_
the index of _this_ filter, but the other one with the same cookie,
because ocelot_vcap_filter_equal() gets fooled.
Then later, ocelot_vcap_block_remove_filter() is coded to remove all
filters that are ocelot_vcap_filter_equal() with the passed @filter.
So unexpectedly, both filters get deleted from the list.
Then ocelot_vcap_filter_del() will attempt to move all the other filters
up, again finding them by index (@i). The block count is 2, @index was 0,
so it will attempt to move up filter @i=0 and @i=1. It assigns tmp =
ocelot_vcap_block_find_filter_by_index(block, i), which is now a NULL
pointer because ocelot_vcap_block_remove_filter() has removed more than
one filter.
As far as I can see, this problem has been there since the introduction
of tc offload support, however I cannot test beyond the blamed commit
due to hardware availability. In any case, any fix cannot be backported
that far, due to lots of changes to the code base.
Therefore, let's go for the correct solution, which is to not call
ocelot_vcap_filter_add() and ocelot_vcap_filter_del(), unless the filter
is actually unique and not shared. For the shared filters, we should
just modify the ingress port mask and call ocelot_vcap_filter_replace(),
a function introduced by commit 95706be13b ("net: mscc: ocelot: create
a function that replaces an existing VCAP filter"). This way,
block->rules will only contain filters with unique cookies, by design.
Fixes: 07d985eef0 ("net: dsa: felix: Wire up the ocelot cls_flower methods")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will enable cleanups down the road.
The idea is to disable cbs, then add "flush_queued_cbs" callback
as a parameter, this way drivers can flush any work
queued after callbacks have been disabled.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20211013105226.20225-1-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
