The bounce buffer, used for misaligned bytes for ADMA access,
resides wholly within the (align_sz)-aligned word, just by construction.
The page addresses are aligned to (align_sz), either for 4 or 8 bytes
alignment, so that the aligned word resides wholly within a single page
and can't cross the page boundary. So, the bounce buffer can't cross
the page boundary too. That's why the warnings are never hit, and can
be safely removed.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since previous patches removed the need for the tuning block patterns
to be exported, let's move them close to the mmc_send_tuning() API.
Those are now intended to be used only by the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API.
This change affects the Exynos variant, since it's the only one which
support the dw_mmc's ->execute_tuning() callback.
It's seems like dw_mmc internal logic expects failed data transfers to
be ended using a stop command. Let the tuning requests also fall into
this category, since there are data transfer involved.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Previously the pm_runtime_put() caused the device to be runtime PM
suspended, but then immediately being resumed when we add the host.
Prevent this unnecessary runtime PM suspend/resume cycle during
->probe() by moving the call to pm_runtime_put() after mmc_add_host().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By configure runtime PM prior we enable the use of it, we close the gap
for strange and unhandled conditions. Moreover it makes us rely on the
driver core, after finalized ->probe(), to request an inactive device
to become runtime PM idle/suspended, which earlier potentially could
happen already at pm_runtime_set_autosuspend_delay().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since sdhci_remove_host() access the device, we need to make sure it's
runtime PM resumed.
To handle clock gating properly in remove, we first have to make sure
the clocks are ungated.
To fix both these issues, by invoking pm_runtime_get_sync() early in
->remove() callback. Later once we disabled runtime PM, we can restore
the usage count.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit ab78029ecc (drivers/pinctrl: grab default handles from device
core), we can rely on device core for setting the default pins.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modify transfer mode for support sdio card,
send cmd and data at the same time for read data transfer,
but send data after cmd for write data transfer.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support sdio card, transfer mode need make a change,
this need to split code and use it in different place,
Add new function to simplify repeat operation.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->cookie is used for handle async request,
we should init it to negative value when new card inserted,
make cookie value invalid.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new function to dump register within a range.
We print 1 register a line before this patch,
this may make debug info too long when we add more register to dump.
The new dump_reg_range() dump to 8 register a line,
and it is easy to use.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By moving the allocation of the slot-gpio data into mmc_alloc_host(),
we can remove the slot-gpio internal calls to mmc_gpio_alloc().
This means mmc_gpio_alloc() has now only one caller left, which
consequence allow us to simplify and remove some of the slot-gpio code.
Additionally, this makes the slot-gpio mutex redundant, so let's remove
it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent when freeing data, let's move the idr_remove() call
from mmc_free_host() into the ->dev_release() callback for the class
device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a step in moving slot-gpio functions/structs closer to the MMC core,
let's add a local header file for slot-gpio.
In this initial step we move mmc_gpio_alloc() into the header file,
to make it available for the MMC core. Following patches will show the
utilization of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We had a mix of using the class device and the parent device while
allocating data through the devm_* managed functions.
Let's be more consistent and always use the parent device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The slot-gpio uses the devm*_ managed functions. Still it provide APIs
to explicitly free requested CD/WP GPIOs, but these API isn't being
used.
Therefore let's simplify slot-gpio by removing these unused APIs. If it
later turns out we need some of them, we can always consider to restore
the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core makes use of the devm_* functions while requesting the
CD/WP GPIOs, let's rely on that.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core makes use of the devm_* functions while requesting the
CD/WP GPIOs, let's rely on that.
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of just printing an error when mmc_of_parse() fails to request
CD/WP GPIO pins, let's propagate all errors, except for -ENOENT.
Earlier only -EPROBE_DEFER was handled correctly.
As a side effect of this change and by relying on host drivers to
handle the errors during ->probe(), we don't need to free any data in
the error path.
This also means we are actually fixing a bug, since we remove the call
to mmc_gpio_free_cd() which wasn't the correct function to invoke to
handle cleanup. Instead that should have been mmc_gpiod_free_cd().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At errors, balance sdhci_pltfm_init() with sdhci_pltfm_free(), to make
sure all data is freed properly.
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Cc: Christian Daudt <bcm@fixthebug.org>
Cc: Matt Porter <mporter@linaro.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move exynos related definition to header file. And this
also changes some of the registers name to match the standard
naming convention.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
[Alim: updated the commit message]
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even though 1MB is reserved for descriptor table in IDMAC,
the dw_mmc host driver is allowed to receive only maximum
128KB block length in one request. This is caused by setting
improper max_blk_count. It needs to be e adjusted so that
descriptor table is used fully. It is found that the performance
is improved with the increased the max_blk_count.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Static checkers complain about the inconsistent NULL checking here:
drivers/mmc/host/mxs-mmc.c:680 mxs_mmc_probe()
warn: variable dereferenced before check 'ssp->dmach' (see line 660)
The variable can't actually be NULL so we can remove the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Removing a relict from reverse engineering of the Android driver code
in sunxi_mmc_clk_set_rate.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixing the register name in sunxi_mmc_reset_host since the
SDXC_HARDWARE_RESET bit is actually located within REG_GCTRL and not
REG_CMDR as it was pointed out by Allwinner.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1) Adding a comment in order to clarify the choice of the locks within
sunxi_mmc_handle_manual_stop
2) As <lixiang@allwinnertech.com> has pointed out the wait_dma variable
was not accessed within the spin lock block in sunxi_mmc_request and so
(even if it should never happend) it would have theoretically been
possible that some other function would access the variable at the same
time as the function. This has been changed now and the function is
using local variables outside the lock and copys the value over during
the lock phase.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The last descriptor might be the first descriptor as well, so use masking to
add the LD (last descriptor) bit and drop the DIC (disable interrupt on
completion) bit rather then hard assignment as hard assignment will override
the FD (first descriptor) bit if there is only 1 descriptor.
Also set the ER (end of ring) bit and clear buf_addr_ptr2 on the last
descriptor, like the android kernel code does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only function of these 'prepare' and 'complete' is to
disable the 'card detect' irq during suspend.
The commit which added this,
commit a48ce884d5
mmc: omap_hsmmc: Introduce omap_hsmmc_prepare/complete
justified it by the need to avoid the registration of new devices
during suspend.
However mmc_pm_notify will set ->rescan_disable in the 'prepare'
stage and clear it in the 'complete' stage, so no card detection
will actually happen.
Also the interrupt will be disabled before final suspend as part
of common suspend processing.
So this disabling of the interrupt is unnecessary, and interferes
with a transition to using common code for card-detect management.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 0718e59ae2 ("mmc: sdhci: move FSL ESDHC reset handling quirk into
esdhc code") states that Freescale esdhc is the only controller which needs
the interrupt registers restored after a reset. So it moves
SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET quirk handling code into the
esdhc-imx driver only. Unfortunately the same controller is used in
other boards which use the of-esdhc driver instead (like powerpc P2020).
Restore interrupts after reset in the sdhci-of-esdhc driver also.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add manual tuning function in CSR atlas7 SoC. It is mainly used
for the UHS-I SD card working SDR50 SDR104 mode.
The tuning principle can be seen in SD spec part1 v3.01 4.2.4.5
(tuning command).
SD host send the cmd19 and set the delay value(0-127).
and the sdcard return 64 bytes data. If the data is same with
the tuning data. The delay value is valid. Execute this commmand
128 times. And calculate the longest window of the valid values.
The value in the middle of this window is the best value.
Signed-off-by: Minda Chen <Minda.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We're running into cases where our enabling of the SDIO interrupt in
dw_mmc doesn't actually take effect. Specifically, adding patch like
this:
+++ b/drivers/mmc/host/dw_mmc.c
@@ -1076,6 +1076,9 @@ static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
mci_writel(host, INTMASK,
(int_mask | SDMMC_INT_SDIO(slot->id)));
+ int_mask = mci_readl(host, INTMASK);
+ if (!(int_mask & SDMMC_INT_SDIO(slot->id)))
+ dev_err(&mmc->class_dev, "failed to enable sdio irq\n");
} else {
...actually triggers the error message. That's because the
dw_mci_enable_sdio_irq() unsafely does a read-modify-write of the
INTMASK register.
We can't just use the standard host->lock since that lock is not irq
safe and mmc_signal_sdio_irq() (called from interrupt context) calls
dw_mci_enable_sdio_irq(). Add a new irq-safe lock to protect INTMASK.
An alternate solution to this is to punt mmc_signal_sdio_irq() to the
tasklet and then protect INTMASK modifications by the standard host
lock. This seemed like a bit more of a high-latency change.
Reported-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the patch (9623b5b mmc: dw_mmc: Disable low power mode if SDIO
interrupts are used) I added code that disabled the low power mode of
dw_mmc when SDIO interrupts are used. That code worked but always
felt a little hacky because we ended up disabling low power as a side
effect of the first enable_sdio_irq() call. That wouldn't be so bad
except that disabling low power involves a complicated process of
writing to the CMD/CMDARG registers and that extra process makes it
difficult to cleanly the read-modify-write race in
dw_mci_enable_sdio_irq() (see future patch in the series).
Change the code to take advantage of the init_card() callback of the
mmc core to do this right at bootup.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In (3fcb027 ARM: MXC: mxcmmc: work around a bug in the SDHC busy line
handling) the optional init_card() callback was added. According to
the original change it was "for now only called from
mmc_sdio_init_card()".
This callback really ought to be called from the SD and MMC init
functions as well. One current user of this callback
(mxcmci_init_card) will not work as expected if you insert an SDIO
card, then eject it and put a normal SD card in. Specifically the
normal SD card will not get to run with 4-bit data.
I'd like to use the init_card() callback to handle a similar quirk on
dw_mmc when using SDIO Interrupts (the "low power" feature of the card
needs to be disabled), so that will add a second user of the function.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host controllers lacking the required internal vmmc regulator may still
follow the spec with regard to the LSB of SDHCI_POWER_CONTROL. Set the
SDHCI_POWER_ON bit when vmmc is enabled to encourage the controller to
to drive CMD, DAT, SDCLK.
This fixes a regression observed on some Qualcomm and Nvidia boards
caused by 5222161 mmc: sdhci: Improve external VDD regulator support.
Fixes: 52221610dd (mmc: sdhci: Improve external VDD regulator support)
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Tested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sleep in atomic context happened on Trats2 board after inserting or
removing SD card because mmc_gpio_get_cd() was called under spin lock.
Fix this by moving card detection earlier, before acquiring spin lock.
The mmc_gpio_get_cd() call does not have to be protected by spin lock
because it does not access any sdhci internal data.
The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After
moving it out side of spin lock it could theoretically race with driver
removal but still there is no actual protection against manual card
eject.
Dmesg after inserting SD card:
[ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511
[ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1
[ 41.677580] INFO: lockdep is turned off.
[ 41.681486] irq event stamp: 61972
[ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c
[ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54
[ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8
[ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114
[ 41.716206] Preemption disabled at:[< (null)>] (null)
[ 41.721500]
[ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883
[ 41.732111] Workqueue: kmmcd mmc_rescan
[ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14)
[ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc)
[ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30)
[ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58)
[ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4)
[ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268)
[ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0)
[ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78)
[ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124)
[ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64)
[ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4)
[ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4)
[ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0)
[ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104)
[ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 42.038276] mmc0: new high speed SDHC card at address 1234
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 94144a465d ("mmc: sdhci: add get_cd() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada
38x SDHCI controller"), the sdhci-pxav3 driver was extended to include
support for the SDHCI controller found in the Armada 38x
processor. This mainly involved adding some MBus window related
configuration.
However, this configuration is currently done too early in ->probe():
it is done before clocks are enabled, while this configuration
involves touching the registers of the controller, which will hang the
SoC if the clock is disabled. It wasn't noticed until now because the
bootloader typically leaves gatable clocks enabled, but in situations
where we have a deferred probe (due to a CD GPIO that cannot be taken,
for example), then the probe will be re-tried later, after a clock
disable has been done in the exit path of the failed probe attempt of
the device. This second probe() will hang the system due to the clock
being disabled.
This can for example be produced on Armada 385 GP, which has a CD GPIO
connected to an I2C PCA9555. If the driver for the PCA9555 is not
compiled into the kernel, then we will have the following sequence of
events:
1. The SDHCI probes
2. It does the MBus configuration (which works, because the clock is
left enabled by the bootloader)
3. It enables the clock
4. It tries to get the CD GPIO, which fails due to the driver being
missing, so -EPROBE_DEFER is returned.
5. Before returning -EPROBE_DEFER, the driver cleans up what was
done, which includes disabling the clock.
6. Later on, the SDHCI probe is tried again.
7. It does the MBus configuration, which hangs because the clock is
no longer enabled.
This commit does the obvious fix of doing the MBus configuration after
the clock has been enabled by the driver.
Fixes: 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-tuning for HS400 mode must be done in HS200
mode. Currently there is no support for that.
That needs to be reflected in the code.
Specifically, if tuning is executed in HS400 mode
then return an error, and do not start the
tuning timer if HS200 tuning is being done prior
to switching to HS400.
Note that periodic re-tuning is not expected
to be needed for HS400 but re-tuning is still
needed after the host controller has lost power.
In the case of suspend/resume that is not necessary
because the card is fully re-initialised. That
just leaves runtime suspend/resume with no support
for HS400 re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The tuning timer is always used if the tuning mode
is 1 and there is a tuning count, irrespective of
whether this is the first call, or any subsequent
call. Consequently the logic to start the timer
can be simplified.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
