cxl devices typically access memory using an MMU in much the same way as
the CPU, and each context includes a state register much like the MSR in
the CPU. Like the CPU, the state register includes a bit to enable
relocation, which we currently always enable.
In some cases, it may be desirable to allow a device to access memory
using real addresses instead of effective addresses, so this adds a new
API, cxl_set_translation_mode, that can be used to disable relocation
on a given kernel context. This can allow for the creation of a special
privileged context that the device can use if it needs relocation
disabled, and can use regular contexts at times when it needs relocation
enabled.
This interface is only available to users of the kernel API for obvious
reasons, and will never be supported in a virtualised environment.
This will be used by the upcoming cxl support in the mlx5 driver.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The cxl_get_phys_dev() API returns a struct device pointer which could
belong to either a struct pci_dev (bare-metal) or platform_device
(powerVM). To avoid potential problems in drivers, remove that API. It
was introduced to allow drivers to read the VPD of the adapter, but
the cxl driver now provides the cxl_pci_read_adapter_vpd() API for
that purpose.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Like on bare-metal, the cxl driver creates a virtual PHB and a pci
device for the AFU. The configuration space of the device is mapped to
the configuration record of the AFU.
Reuse the code defined in afu_cr_read8|16|32() when reading the
configuration space of the AFU device.
Even though the (virtual) AFU device is a pci device, the adapter is
not. So a driver using the cxl kernel API cannot read the VPD of the
adapter through the usual PCI interface. Therefore, we add a call to
the cxl kernel API:
ssize_t cxl_read_adapter_vpd(struct pci_dev *dev, void *buf, size_t count);
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Provide a kernel API and a sysfs entry which allow a user to specify
that when a card is PERSTed, it's image will stay the same, allowing
it to participate in EEH.
cxl_reset is used to reflash the card. In that case, we cannot safely
assert that the image will not change. Therefore, disallow cxl_reset
if the flag is set.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch does two things.
Firstly it presents the Accelerator Function Unit (AFUs) behind the POWER
Service Layer (PSL) as PCI devices on a virtual PCI Host Bridge (vPHB). This
in in addition to the PSL being a PCI device itself.
As part of the Coherent Accelerator Interface Architecture (CAIA) AFUs can
provide an AFU configuration. This AFU configuration recored is architected to
be the same as a PCI config space.
This patch sets discovers the AFU configuration records, provides AFU config
space read/write functions to these configuration records. It then enumerates
the PCI bus. It also hooks in PCI ops where appropriate. It also destroys the
vPHB when the physical card is removed.
Secondly, it add an in kernel API for AFU to use CXL. AFUs must present a
driver that firstly binds as a PCI device. This PCI device can then be using
to do CXL specific operations (that can't sit in the PCI ops) using this API.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the current include file from cxl.h -> cxl-base.h. This current
include file is used only to pass information between the base driver that
needs to be built into the kernel and the cxl module.
This is to make way for a new include/misc/cxl.h which will
contain just the kernel API for other driver to use
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This new header adds callbacks and structs needed by the rest of the kernel to
hook into the cxl infrastructure.
This adds the cxl_ctx_in_use() function for use in the mm code to see if any
cxl contexts are currently in use. This is used by the tlbie() to determine if
it can do local TLB invalidations or not. This also adds get/put calls for the
cxl driver module to refcount the active cxl contexts.
cxl_ctx_get/put/in_use are static inlined here as they are called in tlbie
which we want to be fast (mpe's suggestion).
Empty functions are provided when CONFIG_CXL_BASE is not enabled.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
