The interrupt handling of the RS911x is particularly heavy. For each RX
packet, the card does three SDIO transactions, one to read interrupt
status register, one to RX buffer length, one to read the RX packet(s).
This translates to ~330 uS per one cycle of interrupt handler. In case
there is more incoming traffic, this will be more.
The drivers/mmc/core/sdio_irq.c has the following comment, quote "Just
like traditional hard IRQ handlers, we expect SDIO IRQ handlers to be
quick and to the point, so that the holding of the host lock does not
cover too much work that doesn't require that lock to be held."
The RS911x interrupt handler does not fit that. This patch therefore
changes it such that the entire IRQ handler is moved to the RX thread
instead, and the interrupt handler only wakes the RX thread.
This is OK, because the interrupt handler only does things which can
also be done in the RX thread, that is, it checks for firmware loading
error(s), it checks buffer status, it checks whether a packet arrived
and if so, reads out the packet and passes it to network stack.
Moreover, this change permits removal of a code which allocated an
skbuff only to get 4-byte-aligned buffer, read up to 8kiB of data
into the skbuff, queue this skbuff into local private queue, then in
RX thread, this buffer is dequeued, the data in the skbuff as passed
to the RSI driver core, and the skbuff is deallocated. All this is
replaced by directly calling the RSI driver core with local buffer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103180941.443528-1-marex@denx.de
If a reset is performed, but even the reset fails for some reasons (e.g.,
on Surface devices, the fw reset requires another quirks),
cancel_work_sync() hangs in mwifiex_cleanup_pcie().
# firmware went into a bad state
[...]
[ 1608.281690] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
[ 1608.282724] mwifiex_pcie 0000:03:00.0: rx_pending=0, tx_pending=1, cmd_pending=0
[ 1608.292400] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
[ 1608.292405] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
# reset performed after firmware went into a bad state
[ 1609.394320] mwifiex_pcie 0000:03:00.0: WLAN FW already running! Skip FW dnld
[ 1609.394335] mwifiex_pcie 0000:03:00.0: WLAN FW is active
# but even the reset failed
[ 1619.499049] mwifiex_pcie 0000:03:00.0: mwifiex_cmd_timeout_func: Timeout cmd id = 0xfa, act = 0xe000
[ 1619.499094] mwifiex_pcie 0000:03:00.0: num_data_h2c_failure = 0
[ 1619.499103] mwifiex_pcie 0000:03:00.0: num_cmd_h2c_failure = 0
[ 1619.499110] mwifiex_pcie 0000:03:00.0: is_cmd_timedout = 1
[ 1619.499117] mwifiex_pcie 0000:03:00.0: num_tx_timeout = 0
[ 1619.499124] mwifiex_pcie 0000:03:00.0: last_cmd_index = 0
[ 1619.499133] mwifiex_pcie 0000:03:00.0: last_cmd_id: fa 00 07 01 07 01 07 01 07 01
[ 1619.499140] mwifiex_pcie 0000:03:00.0: last_cmd_act: 00 e0 00 00 00 00 00 00 00 00
[ 1619.499147] mwifiex_pcie 0000:03:00.0: last_cmd_resp_index = 3
[ 1619.499155] mwifiex_pcie 0000:03:00.0: last_cmd_resp_id: 07 81 07 81 07 81 07 81 07 81
[ 1619.499162] mwifiex_pcie 0000:03:00.0: last_event_index = 2
[ 1619.499169] mwifiex_pcie 0000:03:00.0: last_event: 58 00 58 00 58 00 58 00 58 00
[ 1619.499177] mwifiex_pcie 0000:03:00.0: data_sent=0 cmd_sent=1
[ 1619.499185] mwifiex_pcie 0000:03:00.0: ps_mode=0 ps_state=0
[ 1619.499215] mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
# mwifiex_pcie_work hang happening
[ 1823.233923] INFO: task kworker/3:1:44 blocked for more than 122 seconds.
[ 1823.233932] Tainted: G WC OE 5.10.0-rc1-1-mainline #1
[ 1823.233935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1823.233940] task:kworker/3:1 state:D stack: 0 pid: 44 ppid: 2 flags:0x00004000
[ 1823.233960] Workqueue: events mwifiex_pcie_work [mwifiex_pcie]
[ 1823.233965] Call Trace:
[ 1823.233981] __schedule+0x292/0x820
[ 1823.233990] schedule+0x45/0xe0
[ 1823.233995] schedule_timeout+0x11c/0x160
[ 1823.234003] wait_for_completion+0x9e/0x100
[ 1823.234012] __flush_work.isra.0+0x156/0x210
[ 1823.234018] ? flush_workqueue_prep_pwqs+0x130/0x130
[ 1823.234026] __cancel_work_timer+0x11e/0x1a0
[ 1823.234035] mwifiex_cleanup_pcie+0x28/0xd0 [mwifiex_pcie]
[ 1823.234049] mwifiex_free_adapter+0x24/0xe0 [mwifiex]
[ 1823.234060] _mwifiex_fw_dpc+0x294/0x560 [mwifiex]
[ 1823.234074] mwifiex_reinit_sw+0x15d/0x300 [mwifiex]
[ 1823.234080] mwifiex_pcie_reset_done+0x50/0x80 [mwifiex_pcie]
[ 1823.234087] pci_try_reset_function+0x5c/0x90
[ 1823.234094] process_one_work+0x1d6/0x3a0
[ 1823.234100] worker_thread+0x4d/0x3d0
[ 1823.234107] ? rescuer_thread+0x410/0x410
[ 1823.234112] kthread+0x142/0x160
[ 1823.234117] ? __kthread_bind_mask+0x60/0x60
[ 1823.234124] ret_from_fork+0x22/0x30
[...]
This is a deadlock caused by calling cancel_work_sync() in
mwifiex_cleanup_pcie():
- Device resets are done via mwifiex_pcie_card_reset()
- which schedules card->work to call mwifiex_pcie_card_reset_work()
- which calls pci_try_reset_function().
- This leads to mwifiex_pcie_reset_done() be called on the same workqueue,
which in turn calls
- mwifiex_reinit_sw() and that calls
- _mwifiex_fw_dpc().
The problem is now that _mwifiex_fw_dpc() calls mwifiex_free_adapter()
in case firmware initialization fails. That ends up calling
mwifiex_cleanup_pcie().
Note that all those calls are still running on the workqueue. So when
mwifiex_cleanup_pcie() now calls cancel_work_sync(), it's really waiting
on itself to complete, causing a deadlock.
This commit fixes the deadlock by skipping cancel_work_sync() on a reset
failure path.
After this commit, when reset fails, the following output is
expected to be shown:
kernel: mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
kernel: mwifiex: Failed to bring up adapter: -5
kernel: mwifiex_pcie 0000:03:00.0: reinit failed: -5
To reproduce this issue, for example, try putting the root port of wifi
into D3 (replace "00:1d.3" with your setup).
# put into D3 (root port)
sudo setpci -v -s 00:1d.3 CAP_PM+4.b=0b
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142346.18355-1-kitakar@gmail.com
The functions mwifiex_shutdown_sw() and mwifiex_reinit_sw() can be used
for more general purposes than the PCIe function level reset. Also, these
are even not PCIe-specific.
So, let's update the comments at the top of each function accordingly.
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142110.18144-3-kitakar@gmail.com
ath11k_peer_create() is called without its return value being checked,
meaning errors will be unhandled. Add missing check and, as the mutex is
unconditionally unlocked on leaving this function, simplify the exit
path.
Addresses-Coverity-ID: 1497531 ("Code maintainability issues")
Fixes: 701e48a43e ("ath11k: add packet log support for QCA6390")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004100218.311653-1-alex.dewar90@gmail.com
gcc-10 shows a false-positive warning with CONFIG_KASAN:
drivers/net/wireless/ath/ath9k/dynack.c: In function 'ath_dynack_sample_tx_ts':
include/linux/etherdevice.h:290:14: warning: writing 4 bytes into a region of size 0 [-Wstringop-overflow=]
290 | *(u32 *)dst = *(const u32 *)src;
| ~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
Until gcc is fixed, work around this by using memcpy() in place
of ether_addr_copy(). Hopefully gcc-11 will not have this problem.
Link: https://godbolt.org/z/sab1MK
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=97490
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[kvalo@codeaurora.org: remove ifdef and add a comment]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-8-arnd@kernel.org
WDS has long been superseded by 4-addr AP/client and lacks such
fundamental features like encryption, capability negotiation,
and similar. As such, it was basically always unusable as is.
Back in 2016, in commit 8f20542386 ("wireless: deprecate WDS
and disable by default") I disabled it and made the Kconfig option
only available under CONFIG_EXPERT to turn it back on. Since then,
nobody has complained about that, and given the severe limitations
with the code, it's unlikely anyone would have a reason to.
Remove the Kconfig option now, so we can clean up the associated
code in follow-up patches.
Link: https://lore.kernel.org/r/20201109105103.7d1e44c50e21.I2c0a1705fd6491d9ba3400c88415ee2c4832ae98@changeid
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_bt_inquiry’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1451:40: warning: variable ‘bt_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1451:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1451:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_wifi_idle_process’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1519:40: warning: variable ‘bt_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1519:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_pan_hs’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:2990:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_hid_a2dp’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:3277:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-31-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_wifi_idle_process’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:1631:40: warning: variable ‘bt_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:1631:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_sco’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2767:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_hid’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2810:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_a2dp’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2855:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_a2dp_pan_hs’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2929:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_edr’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2976:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_hs’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3028:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3028:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_edr_a2dp’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3066:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_edr_hid’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3121:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_hid_a2dp_pan_edr’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3185:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_hid_a2dp’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3244:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-26-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/intersil/prism54/isl_ioctl.c:22:
inlined from ‘prism54_get_name’ at drivers/net/wireless/intersil/prism54/isl_ioctl.c:283:2:
drivers/net/wireless/intersil/prism54/isl_ioctl.c:68: warning: Function parameter or member 'priv' not described in 'prism54_mib_mode_helper'
drivers/net/wireless/intersil/prism54/isl_ioctl.c:68: warning: Excess function parameter 'mib' description in 'prism54_mib_mode_helper'
drivers/net/wireless/intersil/prism54/isl_ioctl.c:127: warning: Function parameter or member 'priv' not described in 'prism54_mib_init'
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aurelien Alleaume <slts@free.fr>
Cc: Valerio Riedel <hvr@gnu.org>
Cc: "Luis R. Rodriguez" <mcgrof@ruslug.rutgers.edu>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-15-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_usb.c:26: warning: cannot understand function prototype: 'u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL; '
drivers/net/wireless/rsi/rsi_91x_usb.c:88: warning: Function parameter or member 'endpoint' not described in 'rsi_write_multiple'
drivers/net/wireless/rsi/rsi_91x_usb.c:88: warning: Excess function parameter 'addr' description in 'rsi_write_multiple'
drivers/net/wireless/rsi/rsi_91x_usb.c:320: warning: Function parameter or member 'ep_num' not described in 'rsi_rx_urb_submit'
drivers/net/wireless/rsi/rsi_91x_usb.c:320: warning: Function parameter or member 'mem_flags' not described in 'rsi_rx_urb_submit'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-3-lee.jones@linaro.org
halbtc_send_bt_mp_operation() uses in_interrupt() to determine if it is
safe to invoke wait_for_completion().
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
Aside of that in_interrupt() is not correct as it does not catch preempt
disabled regions which neither can sleep.
halbtc_send_bt_mp_operation() is called from:
rtl_watchdog_wq_callback()
rtl_btc_periodical()
halbtc_get()
case BTC_GET_U4_BT_PATCH_VER:
halbtc_get_bt_patch_version()
which is preemtible context.
rtl_c2h_content_parsing()
btc_ops->btc_btinfo_notify()
rtl_btc_btinfo_notify()
exhalbtc_bt_info_notify()
ex_btc8723b1ant_bt_info_notify()
ex_btc8821a1ant_bt_info_notify()
ex_btc8821a2ant_bt_info_notify()
btcoexist->btc_set_bt_reg()
halbtc_set_bt_reg()
rtl_c2h_content_parsing() is in turn called from:
rtl_c2hcmd_wq_callback()
rtl_c2hcmd_launcher()
which is preemptible context and from:
_rtl_pci_rx_interrupt
rtl_c2hcmd_enqueue()
which is obviously not preemptible but limited to C2H_BT_MP commands
which does invoke rtl_c2h_content_parsing().
Aside of that it can be reached from:
halbtc_get()
case BTC_GET_U4_SUPPORTED_FEATURE:
halbtc_get_bt_coex_supported_feature()
case BTC_GET_U4_BT_FORBIDDEN_SLOT_VAL:
halbtc_get_bt_forbidden_slot_val()
case BTC_GET_U4_BT_DEVICE_INFO:
halbtc_get_bt_device_info()
case BTC_GET_U4_SUPPORTED_VERSION:
halbtc_get_bt_coex_supported_version()
case BTC_GET_U4_SUPPORTED_FEATURE:
halbtc_get_bt_coex_supported_feature()
btcoexist->btc_get_bt_afh_map_from_bt()
halbtc_get_bt_afh_map_from_bt()
btcoexist->btc_get_ble_scan_para_from_bt()
halbtc_get_ble_scan_para_from_bt()
btcoexist->btc_get_ble_scan_type_from_bt()
halbtc_get_ble_scan_type_from_bt()
btcoexist->btc_get_ant_det_val_from_bt()
halbtc_get_ant_det_val_from_bt()
btcoexist->btc_get_bt_coex_supported_version()
halbtc_get_bt_coex_supported_version()
btcoexist->btc_get_bt_coex_supported_feature()
halbtc_get_bt_coex_supported_feature()
None of these have a caller. Welcome to the wonderful world of HALs and
onion layers.
Remove in_interrupt() check.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-9-bigeasy@linutronix.de
is_any_client_connect_to_ap() is using in_interrupt() to determine whether
it should acquire the lock prior accessing the list.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
The function is called from:
- halbtc_get()
- halbtc_get()
halbtc_get_wifi_link_status()
- halbtc_display_dbg_msg()
halbtc_display_wifi_status()
halbtc_get_wifi_link_status()
All top level callers are part of the btc_coexist callback inferface and
are never invoked from a context which can hold the lock already.
The contexts which hold the lock are either protecting list add/del
operations or list walks which never call into any of the btc_coexist
interfaces.
In fact the conditional is outright dangerous because if this function
would be invoked from a BH disabled context the check would avoid taking
the lock while on another CPU the list could be manipulated under the lock.
Remove the in_interrupt() check and always acquire the lock.
To simplify the code further use list_empty() instead of walking the list
and counting the entries just to check the count for > 0 at the end.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-8-bigeasy@linutronix.de
issuecommand() is using in_atomic() to decide if it is safe to invoke
schedule() while waiting for the command to be accepted.
Usage of in_atomic() for this is only half correct as it can not detect all
condition where it is not allowed to schedule(). Also Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
Add an may_sleep argument to issuecommand() indicating when it is save to
sleep and change schedule() to cond_resched() because it's pointless to
invoke schedule() if there is no request to reschedule.
Pass the may_sleep condition through the various call chains leading to
issuecommand().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-5-bigeasy@linutronix.de
issuecommand() is using in_atomic() to decide if it is safe to invoke
schedule() while waiting for the command to be accepted.
Usage of in_atomic() for this is only half correct as it can not detect all
condition where it is not allowed to schedule(). Also Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
Chasing the call chains leading up to issuecommand() is straight forward,
but airo_link() and airo_get_stats() would require to pass the context
through a quite large amount of functions.
As this is ancient hardware, avoid the churn and enforce the invocation of
those functions through the JOB machinery.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-4-bigeasy@linutronix.de
The usage of in_irq()/in_interrupt() in drivers is phased out and the
BUG_ON()'s based on those are not covering all contexts in which these
functions cannot be called.
Aside of that BUG_ON() should only be used as last resort, which is clearly
not the case here.
A broad variety of checks in the invoked functions (always enabled or debug
option dependent) cover these conditions already, so the BUG_ON()'s do not
really provide additional value.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-2-bigeasy@linutronix.de
Originally driver checks if firmware has left lps via reading the setting
of REG_TCR register. But this way may fail when firmware is frequently
changing power state. Therefore, firmware provides a safer option for
driver. When firmware leaves lps successfully, it sends a C2H response
to inform driver.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-4-tehuang@realtek.com
Some functions need the support of firmware with special version.
In order to get the feature of current firmware, we store the information
in firmware header and parse after firmware is loaded. The current feature
list in firmware header includes checking leave lps via C2H and
supported lps deep mode.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-3-tehuang@realtek.com
